Acer 5210 Laptop User Manual

Acer
Aspire 5110/5100/3100
TravelMate 5510/5210
Extensa 5410/ 5010
Service Guide
Service guide files and updates are
available on the ACER/CSD web.
For more information, please refer to
http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates of Aspire 5110/5100/3100 and TravelMate 5510/
5210 and Extensa 5410/5010 service guide.
Date
April 26, 2007
II
Chapter
Updates
New model name added
Copyright
Copyright© 2006 by Acer Incorporated. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
III
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness
for any particular purpose. Any Acer Incorporated software described in this manual is sold or
licensed “as is”. Should the programs prove defective following their purchase, the buyer (and not
Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing,
repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Incorporated.
AMD is a registered trademark of AMD Corporation.
Turion and Athlon are trademarks of AMD Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective
holders.
IV
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information related
to the current topic.
WARNING
Alerts you to any damage that might result from doing
or not doing specific actions.
CAUTION
Gives precautionary measures to avoid possible
hardware or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the
accomplishment of procedures.
V
Preface
Before using this information and the product it supports, please read the following general
information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's “global” product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. addon card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this
generic service guide. In such cases, please contact your regional offices or the responsible personnel/
channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reason, if a part number change is made, it will not be noted
in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have
a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use
the list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
VI
Table of Contents
Chapter 1 System Specification 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TV-Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Keys and Controls . . . . . . . . . . . . . . . . . . . . . . .
I/O Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
2
2
2
2
3
3
3
4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Outlook Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Base View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock keys and Embedded Numeric Keypad . . . . . . . . .
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
12
13
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Easy-launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . .
Empowering Technology Password . . . . . . . . . . . . . . .
Acer eDataSecurity Management (for selected models)
Acer eLock Management . . . . . . . . . . . . . . . . . . . . . . .
Acer ePerformance Management . . . . . . . . . . . . . . . . .
Acer eRecovery Management . . . . . . . . . . . . . . . . . . .
Acer eSettings Management . . . . . . . . . . . . . . . . . . . . .
Acer ePower Management . . . . . . . . . . . . . . . . . . . . . .
Acer ePresentation Management . . . . . . . . . . . . . . . . .
18
18
18
20
21
22
23
24
26
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Acer GridVista (dual-display compatible) . . . . . . . . . . . 27
Launch Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
VII
Norton AntiVirus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
How do I check for viruses? . . . . . . . . . . . . . . . . . . . . . 29
Hardware Specification and Configuration . . . . . . . . . . . . . . 30
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Invoking BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 2 System Utilities 41
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
DOS Flash SOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Chapter 3 Machine Disassembly and Replacement 53
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . 55
Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . 57
Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . 57
Removing the RAM Module/Mini PCI Card/Thermal Module/CPU
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Removing the ODD Module . . . . . . . . . . . . . . . . . . . . . 60
Removing the LCD Module from the Main Unit . . . . . . 61
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . 62
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . 63
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . 68
Chapter 4 Troubleshooting 71
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . .
External Diskette Drive Check . . . . . . . . . . . . . . . . . . .
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . .
Keyboard or Auxiliary Input Device Check . . . . . . . . . .
Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . .
Check the Power Adaptor . . . . . . . . . . . . . . . . . . . . . . .
Check the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . .
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
72
72
72
73
73
73
74
74
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . 76
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . 76
POST Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . 80
VIII
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Chapter 5 Jumper and Connector Location 86
Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Top Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Bottom Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Top Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Bottom Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Chapter 6 FRU (Field Replacement Unit) List 92
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
IX
Chapter 1
System Specification
Features
NOTE: This product line has both UMA and Discrete SKU. The Discrete SKU has thermal module and the
UMA SKU has no thermal module.
Platform
• AMD TurionTM 64 X2 dual-core TL-50/TL-52/TL-56/TL-60/TL-62 processor or higher with 1MB L2
cache, supporting AMD PowerNow!TM Technology and AMD HyperTransportTM Technology
• Mobile AMD SempronTM 3200+/3400+/3500+ or higher with 512KB L2 cache, supporting AMD
PowerNow!TM Technology and AMD HyperTransportTM Technology, 64bit OS compatible
• ATI Radeon® Xpress 1100 or Xpress 1200 chipset
System Memory
• Up to 2GB of DDR2 533/667MHz memory, upgradeable to 4GB using two soDIMM modules (dualchannel support)
Display
• 15.4” WXGA Acer CrystalBriteTM TFT LCD, 1280 x 800 pixel resolution, 16 ms response time,
supporting simultaneous multi-window viewing on dual displays via Acer GridVistaTM
• 15” XGA colour TFT LCD, 1024 x 768 pixel resolution
Graphics
• ATI Radeon® Xpress 1100 chipset with integrated 3D graphics, up to 256MB of shared system memory
• ATI MobilityTM Radeon® X1300/X1600 with up to 512MB of HyperMemoryTM (64MB of dedicated
GDDR2 VRAM; up to 448MB of shared system memory), supporting ATI PowerPlayTM 5.0, Microsoft®
DirectX® 9.0, PCI Express®, DualViewTM support
• 16.7 million colours
• MPEG-2/DVD hardware-assisted capability
• S-video/TV-out (NTSC/PAL) support (for selected models)
• Acer ArcadeTM, featuring Acer CinemaVisionTM and Acer ClearVisionTM technology
TV-Tuner
• Acer TV-tuner options (for selected models):
• Analog TV-tuner supporting hardware MPEG-2 stream encoding
• Digital and analog hybrid TV-tuner supporting hardware MPEG-2 stream encoding
• Digital and analog hybrid TV-tuner supporting software MPEG-2 stream encoding
• Analog TV-tuner supporting international analog TV standards (NTSC/PAL/SECAM)
Chapter 1
1
• Digital TV-tuner supporting DVB-T (Digital Video Broadcasting Terrestrial) standard (6MHz to 8MHz)
TV-tuner I/O:
• RF jack for digital/analog TV antenna cable input
• AV-in port for composite/S-video/line-in audio/video input
• TV-tuner cables:
• NTSC/PAL cable for digital/analog TV input, NTSC converter to convert port from PAL/SECAM
to NTSC
• Mini DIN cable: RCA jack and S-video port for audio/video input
• Acer DVB-T antenna (UHF/VHF reception) supports Acer SignalUpTM wireless technology
Audio
• High Definition audio support
• S/PDIF (Sony/Philips Digital Interface) support for digital speakers (for selected models)
• Audio system with two built-in speakers
• Sound Blaster ProTM and MS Sound compatible
• Built-in microphone
Storage Subsystem
• 40/60/80/100/120GB or higher ATA/100 hard disk drive
• Optical drive options:
• DVD-Super Multi double-layer drive
• DVD/CD-RW combo drive
• 5-in-1 card reader, supporting Secure Digital (SD), MultiMediaCard (MMC), Memory Stick® (MS),
Memory Stick PROTM (MS PRO), xD-Picture CardTM (xD) (for selected models)
Communication
• Acer Video Conference featuring Voice and Video over Internet Protocol (VVoIP) support via Acer
OrbiCamTM and optional Acer Bluetooth® VoIP phone (for selected models)
• Acer OrbiCamTM integrated 310,000 pixel CMOS camera (for selected model) featuring:
• 225 degree ergonomic rotation
• Acer PrimaLiteTM technology
• Modem: 56K ITU V.92 with PTT approval; Wake-on-Ring ready
• LAN: gigabit or Fast Ethernet; Wake-on-LAN ready
• WPAN: Bluetooth® 2.0 + EDR (Enhanced Data Rate)
• WLAN: Acer InviLinkTM 802.11b/g or 802.11a/b/g Wi-Fi CERTIFIEDTM solution, supporting Acer
SignalUpTM wireless technology
Special Keys and Controls
• 88/89-key keyboard, with inverted “T” cursor layout; 2.5 mm (minimum) key travel, international
language support
• Touch pad with 4-way scroll button
• 12 function keys, four cursor keys, two Windows® keys, hotkey controls, embedded numeric keypad
2
Chapter 1
• Four easy-launch buttons: Empowering Key, email, Internet and user-programmable button
• Six/Seven media keys: TV, volume up, volume down, play/pause, stop, previous, next (for selected
models)
• Two communication switches: WLAN, Bluetooth®
• Acer remote controls (for selected models):
• Acer ArcadeTM (48 keys)
• Windows® Media Center Edition (Uses an external USB CIR receiver)
I/O Interface
• ExpressCardTM /34 slot (for selected models)
• PC Card slot (one Type II)
• 5-in-1 card reader (SD/MMC/MS/MS PRO/xD) (for selected models)
• Four USB 2.0 ports (three for selected models)
• DVI-D port (for selected models)
• IEEE 1394 port (for selected models)
• Consumer infrared (CIR) port (for selected models)
• External display (VGA) port
• AV-in port (for selected models)
• RF-in jack (for selected models)
• S-video/TV-out (NTSC/PAL) port (for selected models)
• Headphones/speaker/line-out jack with S/PDIF support (for selected models)
• Microphone-in jack
• Line-in jack
• Ethernet (RJ-45) port
• Modem (RJ-11) port
• DC-in jack for AC adapter
Power Subsystem
• ACPI 2.0 CPU power management standards: Stand-by and Hibernation power-saving modes support
• 71W 4800mAh (8-cell) Li-ion battery pack
• 44W 4000mAh (6-cell) Li-Ion battery
• 29.6W 2000mAh (4-cell) Li-ion battery
• Acer QuicChargeTM technology: 80% charge in 1 hour; 2-hour rapid charge system-off; 2.5-hour
charge-in-use
NOTE: Only support for SKU with 90W adapter.
• 3-pin 65/90W AC adapter
Dimensions and Weight
Aspire 5110
• 358 (W) x 269 (D) x 29.8/33.8 (H) mm (14.1 x 10.6 x 1.17/1.33 inches)
• 3.0 kg (6.61 lbs.) for 15.4” LCD model with TV module
• 2.92 kg (6.44 lbs.) for 15.4” LCD model without TV module
Chapter 1
3
Aspire 5100/3100 Series
• 358 (W) x 269 (D) x 29.8/33.8 (H) mm (14.1 x 10.6 x 1.17/1.33 inches)
• 2.82 kg (6.22 lbs.) for 15.4” LCD model
• 2.78 kg (6.13 lbs.) for 15” LCD model
Environment
• Temperature:
• Operating: 5 oC to 35 oC
• Non-operating: -20 oC to 65 oC
• Humidity (non-condensing):
• Operating: 20% to 80%
• Non-operating: 20% to 80%
4
Chapter 1
Block Diagram
Mini PCI Socket
Mini card
Realtek
RTL8100CL
RTL8110SCL
RJ45 CONN
Thermal Sensor
ADM1032ARM
CRT & TV-OUT
LCD CONN
1394
Conn.
HT 16x16 800MHZ
H_D#(0..63)
AMD Turion/Sempron CPU
Socket S1 638P
465 BGA
2 x PCIE
549 BGA
DDRII
533/667
Dual Channel
BT Conn
DDRII-SO-DIMM X2
AMP & Audio Jack
USB conn x 2 / New card
USB 2.0
Audio CKT
ALC883
SATA HDD Conn.
MDC Conn.
AC-LINK
SATA
BIOS
Int. KBD
PATA One Channel HDD Conn.
CDROM Conn.
ENE KB910
ATI-SB460
LPC BUS
USB 2.0
A-Link Express
ATI-RS485MC
H_A#(3..31)
1394 Controller
VT6311S
Clock Generator
ICS951462
PCI BUS
RTC CKT.
FIR module
SMsC LPC47N207
5in1 CardReader
Slot
CB714
ENE Controller
Slot 0
CIR/LED
Power On/Off CKT / LID switch / Power OK CKT
DC/DC Interface CKT.
Power Circuit DC/DC
Touch Pad
CONN.
5
Chapter 1
Outlook Tour
Front View
#
Item
#
6
Just for Starters...
Item
Description
Description
1
Display screen
Also called Liquid-Crystal Display (LCD), displays computer output.
2
Keyboard
Serves for entering data into your computer.
3
Touchpad
Touch-sensitive pointing device which functions like a computer
mouse
4
Click buttons
(left, center and right)
The left and right buttons function like the left and right mouse
buttons; the center button serves as a four-way scroll button.
5
Palmrest
Comfortable support area for your hands when you use the
computer.
6
Microphone
Internal microphone for sound recording.
7
TV/media/volume buttons
For use with Acer Arcade and other media playing programs (for
selected models).
8
Easy-launch buttons
Buttons for launching frequently used programs.
9
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the status of the
computer’s functions and components.
10
Power button
Turns the computer on and off.
Chapter 1
#
Icon
Item
"Launch keys" on page 10
Description
"Launch keys" on page
10
Closed Front View
#
#
#
#
Icon
Icon
Item
Item
Icon
1
N/A
#
#2
Icon
Icon
Description
Item
Description
Description
#
Item
"Launch
keys" on page 10
Icon
Item
Speakers
Description
Description
Left and right speakers deliver stereo audio output.
Item
Description
Bluetooth
Enables/disables
Item communication
Descriptionthe Bluetooth communication.
button/indicator
Indicates the status of Bluetooth communication (for selected
models).
3
Wireless communication
button/indicator
Enables/disables the wireless function.
Indicates the status of wireless LAN communication.
4
Power indicator
Indicates the computer’s power status.
5#
Icon
6
7#
Item
Battery indicator Description Indicates the computer’s battery status.
CIR receiver
Icon
8
Item
Microphone-in jack Description
Accepts input from external microphones.
Line-in jack
#
9
Icon
10
N/A
Receives signals from a remote control (for selected
models).
Item
Headphones/speaker/
line-out jack with S/PDIF
support
Latch
Accepts audio line-in devices (e.g., audio CD player, stereo
walkman).
Description
Connects to audio line-out devices (e.g., speakers,
headphones).
Locks and releases the lid.
Note:
Chapter 1
7
#
Icon
#
Item
Item
Description
Description
Left View
"Easy-launch buttons" on page 10
#
"Launch keys" on page 10
Icon
#
Icon
Item
#
1
Icon
Description
Item
Description
Item
Kensington lock slot
Description
Note:
Connects to a Kensington-compatible computers security
lock.
#
Icon
2
Item
N/A
Description
Ventilation slots
3
Enable the computer to stay cool, even after prolonged use.
Three USB 2.0 ports
#
Icon
4
Item
Description
Ethernet (RJ-45) port
Note:
#
Icon
Item
Description
Connect to USB 2.0 devices (e.g., USB mouse, USB
camera).
Connects to an Ethernet 10/100-based or 10/100/1000based networks.
5
Infrared port
Interfaces with infrared devices (e.g., infrared printer and IRaware computer) (optional).
6
5-in-1 card reader
Accepts Memory Stick (MS), Memory Stick Pro (MS PRO),
MultiMediaCard (MMC), Secure Digital (SD) and xD-Picture
Card (xD) (optional).
#
Icon
Item
7
#
4-pin IEEE 1394 port
Item
Icon
8
9
Description
PC Card slot
#
10
Icon
Item
Accepts one Type II PC Card.
ExpressCard/34 slot
N/A
Connects to IEEE 1394 devices (optional).
Description
Description
Accepts one ExpressCard/34 module (optional).
PC Card slot eject button Note:
Ejects the PC Card from the slot.
Right View
#
Icon
#
#
Item
Item
Description
Description
Description
1
Optical disk drive
Internal optical drive; accepts CDs or DVDs.
2
Optical disk access
indicator
Lights up when the optical disk drive is active.
3
Optical disk drive eject
button
Ejects the drive tray from the drive.
4
Emergency eject hole
Ejects the drive tray when the computer is turned off.
#
8
Item
Icon
Item
Description
Chapter 1
Note:
Rear View
#
#
##
#
#
1
#
Icon
Icon
Icon
Icon
Item
#
Icon
Item
Item
Icon
Icon
Item
Icon
Item
Description
Description
Item
Item
Item
Description
Aspire 5110 / 5100 / 3100 Series
Description
Description
Description
Description
Modem (RJ-11) port
Connects to a phone line.
Description
2
Two USB 2.0 ports
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
3
RF-in jack
Accepts input signals from analog/digital TV-tuner devices (for
selected models).
4
AV-in port
5
#
Icon
6
7
Note:
Accepts input signals from audio/video (AV) devices (for
selected models).
Power jack
Item
Connects to an AC adapter.
Description
S-video port/TV out port
(NTSC/PAL) port
#
8
#
Icon
Icon
9
10
N/A
External display (VGA) port Connects to an external display device (e.g., external monitor,
Description
LCD projector).
Item
DVI-D port
Supports digital video connections (for selected models).
Description
Note:
Item
USB 2.0 port
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
Ventilation slots
Enable the computer to stay cool, even after prolonged use.
#
Icon
Item
#
Icon
Item
#
Icon
Item
Description
Description
Description
Chapter 1
#
Connects to a television or display device with S-video input
(for selected models).
9
Item
Description
Base View
#
10
Item
#
Item
Description
Description
1
Hard disk bay
Houses the computer’s hard disk (secured with screws).
2
Memory compartment
Houses the computer’s main memory.
3
Ventilation slots and
cooling fan
Helps keep the computer cool.
NOTE:Note
Do not cover or obstruct the opening of the fan.
4
Battery lock
Locks the battery in position.
5
Battery bay
Houses the computer’s battery pack.
Chapter 1
Using the Keyboard
The full-sized keyboard includes an embedded numeric keypad, separate cursor, lock, Windows,
function and special keys.
Lock keys and Embedded Numeric Keypad
The keyboard has three lock keys which you can toggle on and off.
Lock Key
Lock key
Caps Lock
Description
Description
When Caps Lock is on, all alphabetic characters are typed in uppercase.
When Num Lock is on, the right hand side numeric keypad is in numeric mode. The
Num Lock
function as a calculator (complete with the arithmetic operators +, -, *, and /).
<F11>
<Fn> + <F11> <Fn> +keys
When Num Lock is off, the keys assume cursor and other shortcut functions.
Scroll Lock
<Fn> + <F12>
When Scroll Lock is on, the screen moves one line up or down when you press the
up or down arrow keys respectively. scroll Lock does not work with some
applications.
<Fn> + <F12>
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small
characters located on the upper right corner of the keycaps. To simplify the keyboard legend,
cursor-control key symbols are not printed on the keys.
Desired access
Desired access
Num Lock on
Num Lock on
Num Lock off
Num Lock off
Number keys on embedded
keypad
Type numbers in a normal
manner.
N/A
Cursor-control keys on embedded
keypad
Hold <Shift>
while using cursor<Shift>
control keys.
Hold
<Fn><Fn> while using cursorcontrol keys.
Main keyboard keys
<Fn>
Hold <Fn>
while typing letters on
embedded keypad.
Type the letters in a normal
manner.
Chapter 1
11
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Key
Key
Windows key
Description
Icon
Description
Press alone. This key has the same effect as clicking on the Windows
Description
Start
button. It launches the Start menu. It can also be used with other
keys to provide a variety of functions:
Key
+ <Tab>: Activates the next Taskbar button.
<
+ <E>: Opens the My Computer window.
> + <Tab>:
<
+><F1>:
+ <E>:Opens Help and Support.
<
+ <F1>:
+><F>:
Opens the Find (All Files dialog box).
<
+ <R>: Opens the Run dialog box.
> + <F>:
+ <R>:
<
> + <Tab>:
<
> + <E>:
+ <M>: Minimizes all windows.
> + <M>:
<Shift>
<Shift>++ <
Application key
<
<
> + <F1>:
+ +<M>:
>
<M>:Undoes the minimize all windows action.
This key has the same effect as clicking the right mouse button. It
opens the application’s context menu.
<
> + <F>:
+ <R>:
Hotkeys
<
> + <M>:
The computer employs hotkeys or key combinations to access most of the computer's controls like
screen brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the
<Fn> <Shift> + <
> + <M>:
<Fn> key before pressing the other key in the hotkey combination.
Hotkey
Icon
Function
Hotkey
Icon
Function
Description
Function
Description
Function
Description
<Fn> + <F1>
Hotkey
Icon
Hotkey
Icon
<Fn>Key
+ <F1>
Hot
<Fn>
+ <F1>
<Fn>
+ +<F1>
<Fn>
<F1>
Icon
Description
Function
Description
Hot key help
Displays help on hotkeys.
<Fn> + <F2>
<Fn> + <F2>
<Fn>
+ <F2>
<Fn>
+ <F2>
Launches the
Acer eManager"
eSettings in Acer
"Acer
on
pageEmpowering
20
Technology.
page 20
"Acer eManager" on
<Fn> + <F2>
<Fn> + <F3>
<Fn>
+ <F3>
<Fn>
+ <F3>
<Fn> + <F3>
<Fn>
+<F3>
<F4>
<Fn>
<F4>
<Fn>
++ <F4>
<Fn>
+
"Acer eManager" on
Acer eSettings
Acer ePower
Management
Sleep
<Fn>
"Acerin eManager"
Launches the Acer ePower Management
Acer
Empowering
Technology.
page 20
page 20
Leads the computer to Sleep mode.
<Fn> + <F4>
<Fn>
<Fn> ++ <F5>
<F5>
<Fn> <Fn>
+ <F4>
+ <F5>
12
Chapter 1
<Fn> + <F6>
on
<Fn> + <F5>
<Fn>
<Fn>++<F4>
<F5>
<Fn> + <F4>
<Fn>
<Fn>++<F5>
<F4>
<Fn> + <F4>
<Fn><Fn>
+ <F5>
+ <F5>
<Fn>
+<F6>
<F5>
<Fn>
Hot+
Key
<Fn>
+<F5>
<F6>
<Fn>
+
<Fn>
++<F5>
<Fn>
<F5>
Icon
Function
Description
Display toggle
Switches the display output between the display
screen, external monitor (if connected) and both.
<F6>
<Fn>
+++<F7>
<Fn>
<F6>
<Fn>
+
<F6>
<Fn>
++<F6>
<Fn>
<F7>
<Fn>
<F6>
Screen blank
Turns off the display screen backlight to save
power. Press any key to return.
<Fn> + <F6>
<Fn> + <F7>
Touchpad toggle
Turns the internal touchpad on and off.
Speaker toggle
Turns the speakers on and off.
Volume up
Increases the sound volume.
Volume down
Decreases the sound volume.
Brightness up
Increases the screen brightness.
Brightness down
Decreases the screen brightness.
<Fn> + <F6>
<Fn>
+<F8>
<F7>
<Fn>
+
<F7>
<Fn>
+++
<F7>
<Fn>
+ <F7>
<Fn>
<Fn>
<Fn>
+<F7>
<F8>
<Fn> + <F8>
<Fn>
<F8>
<Fn>
<F8>
<Fn>+++
<F8>
<Fn>
+ <F7>
<Fn>
++<< >>
<Fn>
<Fn> + <F8>
<Fn> + <F8>
<Fn>
<>< >>
<Fn>
K
<Fn>
+++
<+
<Fn>
< >
<Fn>
+ <F8>
<Fn>
<Fn>
++<< >>
<Fn>
+<
<
>
<Fn>
++<L
> >
<Fn>
<>
<Fn>
+
<Fn> + < >
<Fn> + < >
<Fn><Fn>
+ < <> >
<Fn>
<Fn>+++<+J
>
<Fn>
<<> >
<Fn> + <
>
< >
<Fn><Fn>
+<
<+ >
<Fn>
+
<Fn> + <
>
<Fn>
I<
> >
<Fn>
+ <+
<Fn>
<Fn>
<Fn>
+ <++<<> >>
<Fn> + <
<Fn>
<Fn> +
+<
<
>
>
>
<Fn>
+ < >keys
Special
<Fn>You
+ can
< locate
> the Euro symbol and the US dollar sign on the upper-center and/or bottom-right side
<Fn>of+the<keyboard.
>
<Fn> + <
>
The Euro Symbol
1. Open a text editor or word processor.
2. Either directly press the <Euro> key on the bottom-right side of the keyboard, orAlt
hold
Gr><Alt Gr> key then
press the number <5> key on the upper-center
side of the keyboard.
<5>
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
Note
The US Dollar Sign
www.microsoft.com/typography/faq/faq12.htm
1. Open a text editor or word processor.
2. Either directly press the <$> key on the bottom-right side of the keyboard, or hold <Shift> and then press
the US dollar sign on the number <4> key.
NOTE: This function varies according to the language settings.
<Shift>
<4>
Chapter 1
13
Note:
#
Item
#
Description
Item
Description
Indicators
The computer has several easy-to-read status indicators. The front panel indicators are visible
Item
Description
even when the computer cover is closed up.
#
"Launch keys" on page 10
"Launch keys" on page 10
"Launch keys" on page 10
#
Item
Description
"Launch keys" on page 10
Icon
#
#
#
Item
Icon
Item
Icon
#
14
Icon
Icon
Item
Icon
HDD
Description
Description
Function Indicates
Description
when the hard disk drive is active.
Description
Caps Lock
Item
Lights up when Description
Caps Lock is activated.
Item Num Lock
Description
Lights up when Num Lock is activated.
Power
Lights when the computer is on.
Battery
Lights when the battery is being charged.
Bluetooth
Indicates the status of Bluetooth communication
Wireless LAN
Indicates the status of wireless LAN communication
Chapter 1
1. Charging:
2. Fully charged:
Easy-launch Buttons
There are several conveniently located easy-launch buttons. They are one user-programmable
button, web browser button, mail button, and Acer Empowering Key . Press
to run the Acer
"Acer are pre-set to E-mail and
Empowering Technology. Although the mail and web browser buttons
Empowering
Technology"
on page 1 by users. To set the web browser, mail and programmable
Internet programs,
they
can be redefined
buttons, run the Acer Launch Manager.
"Launch Manager" on page 37
"Easy-launch
buttons"
"Easy-launch buttons"
on page
10 on page 10
Easy-launch
button button
Easy-launch
Default application
Default application
Acer Empowering Technology (user-programmable)
Mail
E-mail application (user-programmable)
Web browser
Internet browser (user-programmable)
P
User-programmable
"Easy-launch buttons" on page 10
Chapter 1
15
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the
cursor responds as you move your finger across the surface of the touchpad. The central location
on the palmrest provides optimum comfort and support.
Touchpad Basics
Use the touchpad as follows:
(2)
(4) (2) to move the cursor.
• Move your finger across(1)
the touchpad
• Press the left (1) and right (4) buttons located on the edge of the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on
the touchpad (2) is the same as clicking the left button.
(3)
• Use the four-way scroll (3) button to scroll up or down and move left or right a page. This button mimics
your cursor pressing on the right scroll bar of windows applications.
Function
Left button (1)
Right button (4)
Main touchpad (2)
Execute
Quickly click
twice.
Tap twice (at the
same speed as
double-clicking a
mouse button).
Select
Click once
Tap once
Drag
Click and hold.
Then slide your
finger across the
touchpad to
drag the cursor
over the
selection.
Tap twice (at the
same speed as
double-clicking a
mouse button); rest
your finger on the
touchpad on the
second tap and
drag the cursor.
Access context
menu
Scroll
Center button (3)
Click once
Click and hold to
move up/down/
left/right.
NOTE: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to
your finger movements: the lighter the touch, the better the response. Tapping hard will not increase
16
Chapter 1
the touchpad’s responsiveness.
NOTE: By default, vertical and horizontal scrolling is enabled on your touchpad. It can be disabled under
Mouse settings in Windows Control Panel.
Chapter 1
17
Acer Empowering Technology
Acer’s innovative Empowering Technology toolbar makes it easy to have access to the frequently
Acer
eDataSecurity
Management
used functions and
manage
the notebook.
Displayed by default in the upper-right corner of the
screen, it features the following handy utilities:
Acer eLock
Managementprotects data with passwords and advanced encryption algorithms
• Acer eDataSecurity
Management
ePerformance Management
(for selectedAcer
models).
• Acer eLock Management limits access to external storage media.
Acer eRecovery Management
• Acer ePerformance Management improves system performance by optimizing disk space, memory
and registry setting.
Acer eSettings Management
• Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
• Acer eSettings
accesses system information and adjusts settings easily.
AcerManagement
ePower Management
• Acer ePower Management extends battery power via versatile usage profiles.
Acer ePresentation Management
• Acer ePresentation Management connects to a projector and adjusts dispaly settings conveniently.
For more information, right click on the Empowering Technology toolbar, then select the Help or
Tutorial function.
Empowering Technology Password
"Password Setup"
Before using Acer eLock Management and Acer eRecovery Management, You must initialize the
Empowering Technology password. Right click on the Empowering Technology toolbar and select
Password Setup to do so. If you do not initialize the Empowering Technology password, you will
be prompted to do so when running Acer eLock Management or Acer eRecovery Management for
the first time.
Note:
NOTE: If you lose your password, there is no method to reset it except by reformatting your notebook or
taking your notebook to an Acer Customer Service Center. Be sure to remember or write down your
password.
Acer eDataSecurity Management (for selected models)
Acer eDataSecurity Management is a handy file encryption utility that protects the files from being
accessed by unauthorized persons. It is conveniently integrated with Windows Explorer as a shell
extension for quick and easy data encryption/decryption and also supports on-the-fly file encryption
for MSN Messenger and Microsoft Outlook.
The Acer eDataSecurity Management setup wizard will prompt you for a supervisor password and
default encryption. This encryption will be used to encrypt files by default, or you can choose to
enter your own file-specific password when encrypting a file.
NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose
the password, the supervisor password is the only other key capable of decrypting the file. If you lose
both passwords, there will be no way to decrypt your encrypted file! Be sure to safeguard all related
passwords!
18
Chapter 1
Be sure to safeguard all related
passwords!
Chapter 1
19
Acer eLock Management
Acer eLock Management is a security utility that allow you to lock up your removable data, optical
and floppy drives to ensure that data can not be stolen while your notebook is unattended.
• Removable data devices: includes USB disk drives, USB pen drives, USB flash drives, USB MP3
drives, USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can
be mounted as a file system when plugged into the system.
• Optical drive devices: includes any kind of CD-ROM or DVD-ROM drives.
• Floppy disk drives: 3.5-inch disks only.
• Interfaces: includes
Note: serial port, parallel port, infrared (IR), and Bluetooth.
To activate Acer eLock Management, a password must be set at first. Once set, you may apply
locks to any of the three kinds of devices. Lock(s) will be set without any reboot necessary, and will
remain locked after rebooting, until unlocked.
NOTE: If you lose the password, there is no method to reset it except by reformatting the notebook or taking
the notebook to an Acer Customer Service Center. Be sure to remember or write down the password.
20
Chapter 1
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of the
Acer notebook. It provides an express optimization method to release unused memory and disk
space quickly. The user can also enable advanced options for full control over the following options:
• Disk optimization: removes unneeded items and files.
• Speed optimization: improves the usability and performance of the Windows XP system.
• Memory optimization: releases unused memory and check usage.
Chapter 1
21
Acer eRecovery Management
Acer eRecovery Management is a powerful utility with the need for recovery disks provided by the
manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on the
system’s HDD. Be default, user-created backups are stored on D:\ drive. Acer eRecovery
Management provides:
• Password protection
• Recovery of applications and drives
• Image or data backup:
• Backup to HDD (set recovery point)
• Backup to CD or DVD
• Image/data recovery tools:
• Recovery from a hidden partition (factory defaults)
• Recovery from the HDD (most recent user-defined recovery point)
• Recovery from CD or DVD
"Acer
page
NOTE: If the computer did not come with a Recovery
CDeRecovery
or System Management"
CD, please useon
Acer
eRecovery
74
AcerSystem
User's to
Guide
Management’s
“System backup
optical disk” feature to burn a backup image to CD or DVD. To
ensure the best results when recovering the system using a CD or Acer eRecovery Management,
detach all peripherals (except external Acer ODD, if equipped), including the Acer ezDock.
Note:
22
Chapter 1
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specification, change BIOS
passwords or other Windows settings, and to monitor the system health status.
Acer eSettings Management also:
• Provides a simple graphical user interface for navigation.
• Displays general system status and advanced monitoring for power users on Acer computer.
Chapter 1
23
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer
ePower Management from the Empowering Technology interface.
AC Mode (Adapter Mode)
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and
other settings, or click on buttons to turn the following functions on/off: wireless LAN, Bluetooth,
CardBus, fireware (1394), wired LAN and optical device if supported.
DC Mode (Battery Mode)
There are four pre-defined profiles: Entertainment, Presentation, Word Processing, and Battery
Life. You can also define up to three of your own.
To Create a New Power Profile
1. Change power settings as desired.
2. Click Save as... to save to a new power profile.
3. Name the newly created profile.
4. Select whether this profile is for Adapter or Battery mode, then click OK.
5. The new profile will appear in the profile list.
Battery Status
For real-time battery life estimates based on current usage, refer to the panel on the upper half side
of the window.
For additional options, click Settings to:
• Set alarms.
24
"Settings"
Chapter 1
• Reload factory defaults.
• Select what actions to be taken when the cover is closed or the power button is pressed.
• Set passwords for accessing the system after Hibernation or Stand-by.
• View information about Acer ePower Management.
Chapter 1
25
Acer ePresentation Management
Acer ePresentation Management lets you project your computer’s display to an external device or
projector using the hotkey: <Fn> + <F5>. If auto-detection hardware is implemented in the system
and the external display supports it, your system display will be automatically switched out when an
external display is connected to the system. For projectors and external devices that are not autodetected, launch Acer ePresentation Management to choose an appropriate display setting.
NOTE: If the restored resolution is not correct after disconnecting a projector, or you need to use an external
resolution that is not supported by Acer ePresentation Management, adjust your display settings using
Note: or the utility provided by the graphics vendor.
Display Properties
26
Chapter 1
Using the Note:
System Utilities
NOTE: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models.
To enable the dual monitor feature of the notebook,
first ensure
the second
monitor is
Start
Controlthat
Panel
Display
connected, then select Note:
Start, Control Panel, Display and click on Settings. Select the secondary
Settings
(2)
monitor (2) icon in the display box and then click the check box Extend my windows desktop onto
Extend
my
windows
desktop
onto
this monitor. Finally, click Apply to confirm the new settings
andthis
clickmonitor
OK to complete the process.
Apply
OK
Settings
Apply
Start Control Panel Display
(2)
Extend my windows desktop onto this monitor
OK
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view
multiple windows on the same screen. To access this function, please go to Start > All Programs
Start All Programs
Acer GridVista
and click on Acer GridVista.
may choose any one
the four display settings indicated below:
Start You
All Programs
AcerofGridVista
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
Acer GridVista is simple to set up:
1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
Chapter 1
27
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.Note:
Note:
Launch Manager
"Easy-launch
buttons"
on page 24buttons located above the keyboard. You
Launch Manager allows
you to set the
four easy-launch
can access the Launch Manager
by
clicking
on
Start >on
Allpage
Programs
"Easy-launch buttons"
24 > Launch Manager to start the
application.
Start All Programs
Launch Manager
Start All Programs
Launch Manager
28
Chapter 1
Norton AntiVirus
Norton AntiVirus is an anti-virus software that finds and repairs infected files, and protects against
viruses to keep you computer data safe and secure.
How do I check for viruses?
A Full System Scan scans Norton
all files on AntiVirus
your computer. To perform a system scan:
Start
1. Start Norton Antivirus: Double click on the Norton AntiVirus Icon onPrograms
the desktop or click on the Start menu
in
the
Windows
task
bar,
highlight
Programs,
and
select
Norton
Antivirus.
Norton AntiVirus
2. In the Norton Antivirus main window, click Scans.
Scanspanel, click Run FullRun
Full
System
3. In the Scans
System
Scan.
Scans
Scan
4. When the scan is complete, a scan summary appears. Click Finished.
Finished
You can schedule customized virus scans that tun unattended on specific dates and times or at
periodic intervals. If you are using the computer when the scheduled scan begins, it runs in the
background so that you do not have to stop working.
For more information, please refer to the Norton AntiVirus Help menu.
Chapter 1
29
Hardware Specification and Configuration
Processor
Item
Specification
Type
AMD TurionTM 64 X2 dual-core TL-50/
TL-52/TL-56/TL-60/TL-62 processor or
higher
AMD SempronTM 3200+/3400+/3500+
or higher
Package
939 pin lidded micro PGA
754 pin lidded micro PGA
Feature
• Compatible with Existing 32-bit code
base
• Integrated memory controller: 128-bit
DDR SDRAM at 100/133/166/200MHz
• Dual-core architecture: discrete L1
and L2 cache structures for each core
• Compatible with Existing 32-bit code
base
• Integrated memory controller: 64-bit
DDR SDRAM at 100/133/166/200MHz
• HyperTransportTM Technology to I/O
devices: one 16-bit link supporting
speed up to 800MHz (1600 MT/s) or
3.2 GB/s in each direction
• HyperTransportTM Technology to I/O
devices: one 16-bit link supporting
speed up to 1GHz (2000 MT/s) or
4 GB/s in each direction
On-die second
(L2) cache
1024KB
512KB
System Board Major Chips
Item
Specification
Core logic
ATi RS485MC + ATi SB460
Super I/O controller
SMSC SIO1036
Audio controller
Codec ALC883
Video controller
Integrated VGA solution for ATi RS485MC
HDD controller
ATi SB460
Keyboard controller and battery
management unit
ENE KB910
Card bus PCMCIA controller
ENE CB714 (used ENE 1410 when without Card reader function)
LAN controller
RTL8110SBL
IEEE 1394
VIA VT6311S
Hard Disk Drive
Seagate
Model
ST9120821A
ST9120824A
ST9100824
ST9100825A
ST98823A
ST980829A
ST96812A
ST960812A
ST9402112A
80
60
40
3
ST96812A: 3
ST960812A: 2
2
Formatted Gbytes (512 bytes/sector)
120
100
Physical read/write head
4
4
Discs
30
Chapter 1
Hard Disk Drive
Seagate
2
2
2
ST96812A: 2
ST960812A: 1
1
Spindle Speed (RPM):
4200 (ST9120824A, ST9100825A, ST980829A, ST960812A, ST9402112A)
5400 (ST9120821A, ST9100824A, ST98823A, ST96812A)
I/O data transfer rate (Mbytes/sec. max.): 100
ATA data transfer mode supported: PIO modes 0-4; Multiword DMA modes 0-2; Ultra DMA modes 0-5
Voltage tolerance: +5.0V +/- 5%
WD
Model
WD400UE-22HCT0
WD600UE-22HCT0
WD800UE-22HCT0
Formatted Gbytes (512 bytes/sector)
40
60
80
3
4
2
2
5400
5400
Physical read/write head
2
Discs
1
Spindle Speed (RPM):
4200
I/O data transfer rate (Mbytes/sec. max.):
100 ultra DMA mode-5
100 ultra DMA mode-5
100 ultra DMA mode-5
ATA/ATAPI-6; ATA-6
ATA/ATAPI-6; ATA-6
512
512
ATA data transfer mode supported:
ATA/ATAPI-6; ATA-6
Bytes per sector:
512
Max. media transfer rate (disk-buffer, Mbytes/sec.)
372
350
350
+5.0V +/- 5%
+5.0V +/- 5%
Voltage tolerance
+5.0V +/- 5%
BIOS
Item
Description
BIOS vendor
Phoenix
System BIOS version
Phoenix BIOS V0.17A
Chapter 1
31
BIOS
Item
Feature
Description
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Acer UI support
Multi-boot support
1MB flash RIOM for system BIOS
Suspend to RAM (S3) / Disk (S4)
Various hot keys for system control
Support boot option: HDD/Removable device (media bay device)/all USB
ports
Support protocols: SMBIOS 2.3, PCI2.2, WFM2.0
ACPI 2.0/3.0 compliance with Intel Speedstep support C1, C2, C3, C4, S3
and S4 for mobile CPU
DMI utility for BIOS serial number configurable/asset tag
Y2K solution support
BIOS virus protection
WinFlash support
Wake on LAN from S3
Wake on LAN from AC mode
D to D support
System Memory
Item
Description
Chip
ATi SB460
Feature
• 256/512/1024MB + two 1.8V JEDEC standard 200-pin DDRII SODIMM
memory module connectors
• Adjustable 128MB UMA VGA memory share from system memory
VGA
Item
Description
Chip
ATi RS485MC
Features
•
•
•
•
•
VGA memory up to 128MB
Display core frequency of 200MHz
3D graphics engine
Analog display support
Dedicated 2FP (local flat panel) interface: single or dual channel LVDS panel
support up to SWXGA + panel, resolution with frequency range from 25MHz
to 115MHz per channel
• Discrete: 64/128MB with hyper memory technology up to 512MB (64MB +
448MB or 128MB + 384MB) in OS
• UMA: shared 256MB in OS
PCMCIA
Item
32
Description
PCMCIA controller
ENE CB714
Features
• PC Card 95 supported with one Type II
• PCI card bus
Chapter 1
ENE CB714 Card Bus Host Adapter
Item
Feature
Description
•
•
•
•
3.3V operation with I/O 5V tolerance
LFBGA 169-ball package
Pinout compatible with ENE CB1410
PCI interface
1.
2.
3.
4.
Compliant with PCI Local Bus Specification Revision 2.3
Compliant with PCI Bus PW Management Interface Specification Revision 1.1
Compliant with PCI Mobile Design Guide Version 1.1
Compliant with Advanced Configuration and Power Interface Specification Revision
1.0
• CardBus Interface
1. Compliant with PC Card Standard 8.0
2. Standardized Zoomed Video Register Model support
3. SPKOUT CAUDIO and RIOUT#
• Secure Digital Interface
1.
2.
3.
4.
5.
6.
7.
Compliant with SD Host Controller Standard Specification Version 1.0
SD Suspend/Resume Functionality support
DMA mode to minimize CPU overhead support
High speed with the SD clock frequency up to 50MHz support
Contain two 512-byte buffer to maximize the transfer speed
Traffic LED light support
Over current protection support
• Memory Stick Interface
1.
2.
3.
4.
5.
Compliant with Memory Stick PRO Format Specification Version 1.0
4-bit parallel data transfer mode support
Memory stick clock frequency up to 40MHz
DMA mode to minimize CPU to overhead
Traffic LED light support
• SmartMedia/xD-Picture Interface
1. Compliant with SmartMedia Standard 2003
2.
3.
4.
5.
Compliant with xD - PictureCardTM Card Specification Version 1.0
Hardware ECC (1-bit correction and 2-bit detection) Generation
DMA mode to minimize CPU overhead
Traffic LED light support
• Interrupt Configuration
1. Parallel PCI Interrupts support
2. Parallel IRQ and Parallel PCI interrupts
3. Serialized IRQ and PCI interrupts
• Power Management Control Logic
1.
2.
3.
4.
CLKRUN# protocol support
SUSPEND# support
PCI PME# from D3, D2, D1 and D0 support
PCI PME# from D3 cold support
• Zoomed Video port
• Parallel 4-wire power switch interface
Chapter 1
33
Audio
Item
Description
Audio controller
Realtek ALC833 Azadia Codec
Feature
• HD Audio
• SNR > 85
• Codec specification requires:
1.
2.
3.
4.
5.
6.
7.
8.
HD Audio interface
10 DAC (7.1ch + 2CH); 2 ADC
DAC SNR >/= 95dB, ADC SNR >/= 85dB
2 pins with DTS logo codec
S/PDIF out support
All DACs support 44.1K/48/K/96K/192K sample rate
All ADCs support 44.1K/48K/96/192K sample rate
At least 2 GPIOs for customized applications
• One internal array analog microphone
• Two speakers, at least 1W/9cc for each
LAN
Item
Description
LAN controller
Realtek RTL8100CL
Feature
•
•
•
•
Connector type
RJ-45
10/100Mbps operation
10/100Mbps
WOL from S5 support
File deployment support
Wireless LAN
Item
Description
Card type
Mini-PCI
Features
•
•
•
•
802.11b/g
Built-in two antenna
Wi-Fi, WPA2, WMM CCX V3 and above support
To be placed on the top of LCD on the sides of LCD latches
Modem
Item
Description
Controller
ATi SB460
Features
•
•
•
•
Connector type
RJ-11
56K, V.90/V.92, WWDAA
Wake-on-Ring support
CISPR22 application
MDC 1.5 card
Keyboard
Item
Model name
34
Description
New Acer Ergo Keyboard
Chapter 1
Keyboard
Item
Description
Features
•
•
•
•
•
•
•
•
Touch pad with 4-way integrated scroll button
Windows keys and application keys support
Standard pitch, 2.5 mm travel length
Hotkey controls
Embedded numeric keypad
Multi-language support
Spill-proof
Four easy-launch buttons: Internet browser, E-mail with LED, Acer
Empowering, one user-programmable button
Battery
Item
Specification
Vendor & model name
Panasonic/Sanyo/Sony
Features
•
•
•
•
Li-Ion
8-cell of 18650 Li-Ion battery pack (2200mAh cell)
6-cell of 18650 Li-Ion battery pack (2000mAh cell)
4-cell of 18650 Li-Ion battery pack (2000mAh cell)
TV Tuner (for selected models)
Item
Features
Description
• Mini PCI type
• 3 TV tuner modules at least:
1. Analog with HW MPEG2
2. Analog + Digital with HW MPEG2 (Hybrid)
3. Analog + Digital without HW MPEG2 (Hybrid)
LCD 15.4” WXGA
Item
Specification
Vendor & Model
name
QDI
QD15AL02-01
QD15AL02-02
QDI
QD15TL07-01
QD15TL07-02
LPL
LP154W01-TLE1
LP154W01-TLD1
CMO
N154I2-L01
N154I2-L02
Screen Diagonal
15.4” WXGA
15.4” WXGA
15.4” WXGA
15.4” WXGA
Active area
331.2 (W) x 207.0
(H)
331.2 (W) x 207.0
(H)
331.2 (W) x 207.0
(H)
335.0 (W) x 210.7
(H)
Display resolution
1680 x 3 (RGB) x
1050
1280 x 3 (RGB) x
800
1280 x 3 (RGB) x
800
1280 x 3 (RGB) x
800
Display mode
normally white
normally white
normally white
normally white
Surface treatment
• QD15AL02-01
non-glare +
Hardness 3H
• QD15AL02-02
glare + Hard
Coating 3H
• QD15TL07-01
non-glare +
Hardness 3H
• QD15AL07-02
glare + Hard
Coating 3H
• LP154W01TLE1 non-glare
+ Hard Coating
3H
• LP154W01TLD1 glare +
Hard Coating 2H
• N154I2-L01
non-glare +
Hard Coating 3H
• N154I2-L02
glare + Hard
Coating 3H
Pixel
arrangement
RGB vertical
stripe
RGB vertical
stripe
RGB vertical
stripe
RGB vertical
stripe
Chapter 1
35
LCD 15.4” WXGA
Item
Specification
Pixel pitch (mm)
0.1971 (H) x
0.1971 (V)
0.2588 (H) x
0.2588 (V)
0.25875 (H) x
0.25875 (V)
0.2588 (H) x
0.2588 (V)
Typical white
luminance (cd/
m2) also called
brightness
200 (typical)
185 (typical)
200 (typical)
200 (typical)
Contrast ratio
400 (typical)
400 (typical)
400 (typical)
400 (typical)
Respond time
(msec.)
Rise: 6
Decay: 10
Rise: 6
Decay: 10
Rise:6
Decay: 10
Rise: 5
Decay: 11
Normal input
voltage of power
supply
+3.3V (typical)
+3.3V (typical)
+3.3V (typical)
+3.3V (typical)
Power
consumption
(watt)
4.38 (typical)
4.38 (typical)
4.2 (typical)
4.2 (typical)
Weight
585g
585g
560g
540g
Physical size
(mm)
344.5 (W) x 222.5
(V) x 6.5 (T)
344.0 (H) x 222.0
(V) x 6.35 (T)
344.0 (W) x 222.0
(H) x 6.5 (D)
344.0 (W) x 222.0
(H) x 6.2 (D)
Electrical
interface
2 channels LVDS
1 channel LVDS
LVDS
30-pin LVDS
interface
Color support
262,144 colors
262,144 colors
262,144 colors
262,144 colors
Vendor & Model
name
QDI
QD150XL06-0301
LPL
LP150X08-TLA2
CMO
N150X3-L9
AUO
B150XG02 V4
Screen Diagonal
15” XGA
15” XGA
15” XGA
15” XGA
Active area
304.13 (W) x
228.1 (H)
304.128 (W) x
228.096 (H)
304.1 (W) x 228.1
(H)
304.1 (W) x 228.1
(H)
Display resolution
1024 x 3 (RGB) x
768
1024 x 3 (RGB) x
768
1024 x 3 (RGB) x
768
1024 x 3 (RGB) x
768
LCD 15” XGA
Item
36
Specification
Display mode
normally white
normally white
normally white
normally white
Surface treatment
glare + Hardness
3H
non-glare + Hard
Coating 3H
non-glare + Hard
Coating 3H
non-glare +
Hardness 3H
Pixel
arrangement
RGB vertical
stripe
RGB vertical
stripe
RGB vertical
stripe
RGB vertical
stripe
Pixel pitch (mm)
0.297 (H) x 0.297
(V)
0.297 (H) x 0.297
(V)
0.297 (H) x 0.297
(V)
0.297 (H) x 0.297
(V)
Typical white
luminance (cd/
m2) also called
brightness
160 (typical)
170 (typical)
200 (typical)
170 (typical)
Contrast ratio
300 (typical)
250 (typical)
250 (typical)
300 (typical)
Respond time
(msec.)
Rise: 8
Decay: 17
Rise: 10
Decay: 20
Rise: 5
Decay: 11
Rise: 16
Decay: 9
Chapter 1
LCD 15” XGA
Item
Specification
Normal input
voltage of power
supply
+3.3V (typical)
+3.9V (typical)
+3.3V (typical)
+3.3V (typical)
Power
consumption
(watt)
3.96 (typical)
4.76 (typical)
3.96 (typical)
3.9 (typical)
Weight
570g
530g
550g
585g
Physical size
(mm)
317.3 (W) x 242.0
(H) x 5.9 (D)
317.3 (W) x 241.5
(H) x 5.9 (D)
317.3 (W) x 242
(H) x 5.7 (D)
317.3 (W) x 242
(H) x 5.7 (D)
Electrical
interface
1 channel LVDS
LVDS
LVDS
1 channel LVDS
Color support
262,144 colors
262,144 colors
262,144 colors
262,144 colors
AC Adaptor
Item
Specification
Vendor & Model name
LiteOn PA-1900-04AW
Delta 90W ADP-90SB BBAA
Rated voltage
for 100Vac or 240Vac input AC
voltage
for 100Vac or 240Vac input AC
voltage
Input voltage range
from 90Vac to 264Vac
from 90Vac to 265Vac
Rated frequency
for 50Hz or 60Hz
for 50Hz or 60Hz
Frequency range
from 47Hz to 63Hz
from 47Hz to 63Hz
Steady AC current
less than 1.5A rms at 100Vac
input and maximum load
less than 1.5A rms at 100Vac
input and maximum load
Rated voltage
19V
19V
Voltage range
18.05V to 20V
from 18.2V to 19.8V
Rated power
90 W
90 W
Input feature
Output feature
Output ripple and noise
less than 300mVp-p
less than 300mVp-p
Turn on delay time
within two seconds at 115 Vac
input voltage
within two seconds at 115 Vac
input voltage
Temperature
Operating: 0 to 40oC
Non-operating: -31 to 60oC
Operating: 0 to 40oC
Non-operating: -31 to 60oC
24X Combo Drive Interface
Item
Vendor & model name
Specification
PHILIPS SCB5265
LITEON SSC-2485K
HLDS GCC-4244N
Sustained:
DVD: Max 10.56Mbytes/
sec.
CD: 3600Kbytes/sec.
Sustained:
DVD: Max. 10.15Mbytes/
sec.
CD: 3500Kbytes/sec.
Sustained:
DVD: Max. 11.08Mbytes/
sec.
CD: 3600Kbytes/sec.
Performance Specification
Transfer rate (KB/sec.)
Chapter 1
37
Item
Specification
Access Time (Typical)
DVD: Random Access:
125 ms
DVD: Full Stroke: 165ms
CD: Random
Access:105ms
CD: Full Stroke:160ms
DVD: Random Access:
100 ms
DVD: Full Stroke: 190ms
CD: Random
Access:95ms
CD: Full Stroke:180ms
DVD: 120 ms (average)
CD: 110 ms (average)
Buffer Memory
2MB
2MB
2MB
Interface
Compliant to ATA/ATAPI- ATA/ATAPI-6, MMC-3
5
and SFF8090 Ver5,
Revision 1.2.
Applicable disc format
• DVD (read): DVD 5, 9,
10, 18, DVD-ROM,
DVD-Video, DVD-R
3.95G, DVD-R 4.7G,
DVD-RW, DVD+R,
DVD+RW, Multi-Border
DVD-R/DVD-RW, MultiSession DVD+R,
DVD+RW, DVD-RAM
• CD (read): CD-DA, CD
ROM Mode-1, CDROM/XA Mode-2 Form1 and Mode-2 Form-2,
CD-I, Video-CD
(MPEG-1), CD-Text
• CD (write): CD-DA, CDROM Mode-1, CDROM/XA Mode-2 Form1 and Mode-2, CD-i,
Video-CD, CD-Text
CD: CD-DA, CD-ROM
• DVD (read): DVD-ROM
Mode-1, CD-ROM XA
single layer 4.7GB/dual
Mode-2 Form-1 and
layer 8.5GB, DVD-R
Form-2, CD-I Ready,
3.95GB/4.7GB, DVDVideo-CD(MPEG-1),
RW 4.7GB, DVD-RAM
Karaoke-CD, PhotoCD
2.6GB/4.7GB
(Multi-Session), Enhance • CD (read): CD-ROM
CD, CD extra, I-Trax CD
Mode-1, CD-ROM XA,
and UDF
CD-Audio, Mixed Mode
CD-ROM (Audio and
Data Combined), PhotoCD (Single and Multisession), CD-I, Video
CD, CD-Plus/CD-Extra,
CD-Text, CD-R disc,
CD-RW disc
• CD (write): CD-ROM
Mode-1, CD-ROM XA,
CD-Audio, Mixed Mode
(Audio and Data
Combined), CD-I, Video
CD, CD-Plus/CD-Extra,
CD-Text
Loading mechanism
Manual load
Manual load
Manual load
Power Requirement
Max. 1300mA
Max. 1200mA
Max. 1800mA
Input Voltage
5 V +/- 5% (Operating)
5 V +/- 5% (Operating)
5 V +/- 5% (Operating)
N/A
8X Super Multi Interface
Item
Vendor and model
name
Specification
Liteon SSM 8515S
Pioneer DVR-K16RS
Philip SDVD-8821
Sustained:
• DVD: 10.00Mbytes/
sec.
• CD: 3500kbytes/sec.
Sustained:
• DVD: 10.80Mbytes/
sec.
• CD: 3600kbytes/sec.
Sustained:
• DVD: 10.90Mbytes/
sec.
• CD: 3650kbytes/sec.
Performance Specification
Transfer rate read (KB/
sec.)
38
Chapter 1
Item
Specification
Access time / Seek
time
• DVD: random access
130ms
• DVD: full stroke
250ms
• CD: random access
110ms
• CD: full stroke 220ms
• Access time: DVD
160 msec; CD 150
msec.
• Random seek time:
DVD 150 msec; CD
140 msec.
• Full stroke seek time:
DVD 300 msec; CD
290 msec.
• Random access: DVD
130ms; CD 130ms
• Full stroke: DVD
200ms; CD 240ms
Buffer memory
2MB
2MB
2MB
Interface
compliant to ATA/
ATAPI-6, MMC-4 and
SFF8090 Ver5
compliant to SFF8020,
SFF8090
compliant to ATA/ATA5
Applicable disc format
CD-DA, CD-ROM
Mode-1, CD-ROM/XA
Mode-2 Form-1 and
Mode-2 Form-2, CD-I,
Video-CD (MPEG-1),
CD-Text, PhotoCD,
Enhance CD, CD
extra, I-Trax CD and
UDF DVD-ROM, DVDVideo, DVD-Audio,
DVD-R single/multi
border, DVD+R single/
multi session, DVDRW, DVD+RW, DVDRAM
KODAK Photo CD
single and multisession, CD Extra (CD
PLUS), Video CD, CD
text data (read/write),
CD-R (read/write),
DVD-ROM, DVD-R
(read/write), DVD-R DL
(read/write), DVD-RW
(read/write), DVD+RW
(read/write), DVD+R
(read/write), DVD+R
DL (read/write),
DVD+RW (read/write),
DVD+RW high speed
(read/write), DVD-RAM
(read/write)
• DVD read: DVD-5,
DVD-9, DVD-10,
DVD-18, DVD-Video,
DVD-Audio, SACD
(Hybrid), DVD-R,
DVD-R DL, DVD-R
3.95GB, DVD-R
Authoring, DVD-R
multi-border, DVDRW, DVD+R, DVD+R
DL, DVD+R Multisession, DVD+RW,
DVD-RAM V1.0,
DVD-RAM V2.1; CD
read: CD-DA, CDROM Mode-1, CDROM/XA Mode-2
Form-1 and Mode-2
Form-2, CD-i, CD-i
Bridge, Video-CD
(MPEG-1), Karaoke
CD, Photo-CD,
Enhanced CD, CD
Plus, CD Extra, i-trax
CD, CD-Text, CD-R,
CD-RW
• DVD write: DVD Data,
DVD-video; CD write:
CD-DA, CD-ROM
Mode-1, CD-ROM/XA
Mode-2 Form-1 and
Mode-2 Form-2, CD-i,
Video-CD, CD-text
Loading mechanism
Load: manual load/DC
brushless motor
system
N/A
N/A
Power requirement
Max. 1500mA
Max. 1800mA
Max. 1300mA
Input voltage
+5V +/- 5% (operating)
+5V +/- 5% (operating)
+5V +/- 8% (start-up)
+5V +/- 5% (operating)
Chapter 1
39
Item
Specification
Vendor and model name
HLDS GMA-4082N
Performance Specification
Transfer rate read (KB/sec.)
Sustained:
• DVD: 11.08Mbytes/sec.
• CD: 3600kbytes/sec.
Access time / Seek time
• DVD: random access 160ms
• DVD: full stroke 260ms
• CD: random access 140ms
Buffer memory
2MB
Interface
compliant to ATA/ATAPI-6, MMC-4 and SFF8090 Ver5
Applicable disc format
CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2
Form-2, CD-I, Video-CD (MPEG-1), CD-Text, PhotoCD, Enhance
CD, CD extra, I-Trax CD and UDF DVD-ROM, DVD-Video, DVDAudio, DVD-R single/multi border, DVD+R single/multi session,
DVD-RW, DVD+RW, DVD-RAM
Loading mechanism
Load: manual load/DC brushless motor system
Power requirement
Max. 1500mA
Input voltage
+5V +/- 5% (operating)
Fan True Value Table
Fan
40
dBA
RPM
on
off
Fan off
24
0
0
-
Speed 1
29
2400
40
35
Speed 2
32
2800
54
48
Speed 3
35
3100
71
53
Speed 4
38
3500
73
65
Speed 5
40
3800
74
68
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built in the BIOS (Basic Input / Output
System) of computer. Generally speaking, the computer is already properly configured and
optimized, and you do not need to run this utility.
However, if you encounter configuration problems, you may need to run Setup. Otherwise, you can
also refer to Chapter 4 Troubleshooting when problem arises.
Invoking BIOS Setup
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is
prompted on the left-bottom side of the screen).
There are six prime items in the BIOS Setup Utility. They are Information, Main, Advanced,
Security, Boot and Exit. In the coming pages, we will explain the BIOS Setup Utility by item.
Part
Description
Information
Display the system informations.
Main
Allows the user to specify standard IBM PC AT system
parameters.
Security
Provides security setting of the system.
Boot
Allows the user to specify the boot options.
Exit
Allows the user to save CMOS setting and exit Setup.
NOTE: During setup, all Fn function keys and power saving function are disabled.
Chapter 2
41
Information
PhoenixBIOS Setup Utility
. Info.
Main
CPU Type:
:
CPU Speed
:
Advanced
Security
Boot
Exit
AMD Turion (tm) 64 X2 Mobile Technology
1600 MHz
HDD Model Name:
ST9120821AS-(PM)
HDD Serial Number: 5PL08H08
ATAPI Model Name: MATSHITADVD-RAMUJ-8-(SM)
ATAPI Serial Number:
System BIOS Version: V0.17A
VGA BIOS Version: ATi 009.012.001.005
EC BIOS Version:
V0.17A
Serial Number:
HCW5021012617000C01601
Asset Tag Number:
Product Name:
Manufacturer Name:
Aspire 5110
Acer
UUID:
37363032313033353761000FB0F34EC7
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
• CPU type: This item will show the CPU information of the system.
• CPU speed: This item will show the COU clock speed.
• HDD model name: The hard disk model name is automatically detected by the system. If there is no
hard disk present or unknown type, “None” should be shown on this field.
• HDD serial number: If no hard disk or other devices are installed on primary IDE master, it will display a
blank line.
• System BIOS version: This field reports BIOS version of the system.
• VGA BIOS version: This field reports VGA BIOS version of the system.
• Serial Number: This item is the serial number of the system.
• Asset Tag Number: This item is the asset tag number of the system.
• UUID: It shows only when an internal LAN device is available.
42
Chapter 2
Main
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
System Time:
[14:13:43]
System Date:
[05/12/2006]
System Memory:
633 KB
Extended Memory:
1046528 KB
Video Memory
128 MB
Quiet Boot:
[Enabled]
Power on Display:
[Auto]
Network Boot
[Enabled]
F12 Boot Menu:
[Disabled]
D2D Recovery:
[Enabled]
F1 Help
↑↓
Esc Exit
←→
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
• System Time and System Date: The hours are displayed with 24-hour format. The changes in these
two items take effect immediately.
• System Memory: This item reports the memory size of system base memory. The size is fixed to
640KB.
• Extended Memory: It reports the memory size of the extended memory in the system. The extended
memory size is equal to total memory size (one MB).
• Video Memory: It indicates the video memory size.
• Quiet Boot:
• Enabled: Customer Logo is displayed, and Summary Screen is disabled.
• Disabled: Customer Logo is displayed, and Summary Screen is enabled.
• Power on Display:
• Auto: During power on process, the system will detect if any display device is connected on
external video port. If any external display device is connected, the power on display will be only
in CRT (or projector) mode. Otherwise, it will be in LCD mode.
• Both: Both the integrated LCD and the external video port (for an external CRT or projector) will
be enabled simultaneously.
• Network Boot: It permits the users to boot from network.
Chapter 2
43
• F12 Boot Menu:
• Enabled: When it is enabled, the users can modify device boot priority by pressing <F12> during
POST.
• Disabled: When it is not enabled, device boot priority will not be adjustable during POST.
The boot device change is only for one-time change. In other words, when the system is
rebooted, the boot device sequence will be the same as the one defined in the BIOS setup
(Boot option).
• D2D Recovery: It allows the users to enable or disable the disk-to-disk recovery.
44
Chapter 2
Advanced
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Enable ACPI (debug only):
[Yes]
[Enabled]
Infrared Port (FIR)
Advanced Chipset Control
Boot
Exit
Item Specific Help
En/Disable ACPI BIOS
(Advanced Configuration and
Power Interface) Debug only,
remove this option for
production.
F1
Help
↑ ↓
← →
Esc Exit
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub - Menu
F10 Save and Exit
• Enable ACPI (debug only): Enable/Disable ACPI (Advanced Configuration and Power Interface) debug
only, remove this option for production.
• Infrared Port:
• Disabled: No configuration
• Enabled: User configuration
• BIOS or OS chooses configuration
Chapter 2
45
Security
Info.
Main
PhoenixBIOS Setup Utility
Security
Advanced
Supervisor Password Is:
Clear
User Password Is:
Clear
HDD Password Is:
Clear
Boot
Exit
Item Specific Help
Supervisor Password
controls accesses of the
setup utility. It can be used
Set Supervisor Password
Set User Passord
Set HDD Password
[Enter]
[Enter]
Password on Boot:
[Disabled]
[Enter]
to boot up when Password on
boot is enabled.
F1 Help
↑ ↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The system supports three levels of password protection. The password support consists of a
Supervisor Password, User Password, and Hard Disk Password. All the passwords are stored in a
non-volatile storage device (EEPROM).
• Password Policy:
All the passwords will obey the following rules:
• All the passwords can be set or cleared in BIOS Setup Security screen.
• The password entry consists of eight alphanumeric characters. At least one character must be
assigned.
• The valid keys are listed in the table below:
46
Symbol Character
Symbol Name
A-Z
letters A to Z (not case sensitive)
0-9
numerical characters
-
dash
=
equal sign
[
left bracket
Chapter 2
Symbol Character
Symbol Name
]
right bracket
.
period
,
comma
;
semi-colon
/
slash
\
back slash
• The users can not change or remove password during resuming from S4.
• The max. number of times to retry the password is limited to three.
• Supervisor Password:
Supervisor Password controls the access of the whole BIOS Setup Utility. If the Supervisor
Password is set, the system will pop up the password dialog box to ask for the password when
the users press <F2> for entering BIOS Setup Utility.
If the Supervisor Password is set and Password on boot is enabled, the system will pop up the
password dialog box to ask for the password when the system is powered on or resumes for
S4 state.
If the users fail three times consecutively in password verification, the system will be hung up
and the users need to manually power off the system.
• User Password:
If the User Password is set, the system will pop up the password dialog box to ask for the
password when the users press <F2> for entering BIOS Setup Utility.
If the Supervisor Password is not set at first, the User Password can not be set. If the
Supervisor Password is cleared, the User Password will be cleared, too.
If the User Password is set and Password on boot is enabled, the system will pop up the
password dialog box to ask for the password when the system is powered on or resumes for
S4 state.
If the users fail three times consecutively in password verification, the system will be hung up
and the users need to manually power off the system.
• Set Supervisor Password / User Password:
• Highlight the item and press “Enter”, a dialog box will be shown to ask the users to enter new
password and confirm new password.
• If the users want to reset password, a current password will be required to be tapped in at first. If
the current password is correct, the users are permitted to enter new password and confirm new
password for verification. If the verification is OK, the password setting will be complete after the
users press “Enter”.
• If the password entered does not match the current password, a dialog box will be shown to ask
to re-enter the password.
• Set HDD Password: When shown as “Locked”, the hard drive password currently can not be changed
or disabled. To change or disable it, turn off the system and enter Setup immediately after turning it
back on. Press “Enter” to input change, or disable hard drive password.
• Password on Boot: It allows the user to specify whether or not a password is required to boot.
Chapter 2
47
Boot
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
Boot priority order:
1: SATA: ST9120821AS-(S1)
2: IDE 1:
3: IDE 0: MATSHITADVD-RAM UJ-845S-(PM)
4: PCI BEV: Realtek Boot Agent
5: USB HDD:
6: USB CDROM:
7: USB FDD:
8: USB KEY:
Keys used to view or
configure devices:
Up and Down arrows
select a device, then press
<F6> to move it up the list, or
<F5> to move it down the list.
Press <Esc> to exit the menu.
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
This menu allows the users to decide the order of bootable devices to load the operating system. It
identifies all the bootable devices in the system and attempts to boot them in the order specified.
Bootable devices include the diskette drive in module bay, the hard disk and the CD-ROM/DVD
drive in module bay and onboard LAN device.
48
Chapter 2
Exit
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
• Exit Saving Changes: It allows the users to save changes to CMOS and reboot the system.
• Exit Discarding Changes: The users can exit the Setup not to save changes.
• Load Setup Defaults: It allows the users to load default values in CMOS Setup.
• Discard Changes: The users can discard previous changes in CMOS Setup.
• Save Changes: The users can save current changes in CMOS Setup.
Chapter 2
49
DOS Flash SOP
50
1.
Press <F2> to enter Setup Menu, select Boot page to change boot device priority order. Use USB as an
example.
2.
Execute the BIOS.BAT or FLASH.BAT batch file to update BIOS.
Chapter 2
3.
In flash BIOS, the caution message Please do not remove AC power source will show. If AC power
source is plugged, the caution message AC adapter does not exist.
Chapter 2
51
4.
52
Flash status will show as following picture. When you finish BIOS update, the system will shut down or reboot automatically.
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook for
maintenance and troubleshooting. Here, we take an Aspire 5110 as sample for disassembly.
To disassemble the computer, you need the tools below:
• Wrist ground strap and conductive mat for preventing electrostatic discharge
• Small Philips screw driver
• Flat head screw driver
• Hexagonal driver
• Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
Chapter 3
53
General Information
Before You Begin
Before proceeding with the disassembly procedure, you have to make sure that:
1.
The system and all peripherals are powered off.
2.
The AC adaptor and all power and signal cables from the system are unplugged.
3. The battery pack is removed.
NOTE: There are several types of screws used to secure the main unit. The screws vary in length. Please
refer to the screws table after the flowchart. Group the same type of screws together during service
disassembling. Please also remember the screw location for each screw type. If you fasten the screws
on the wrong location, the long screws may cause irrecoverable damage to the main board.
54
Chapter 3
Disassembly Procedure Flowchart
The flowchart gives you a graphic representation on the entire disassembly and reassembly and
instructs you how to remove the components.
Screws List
No.
Description
Part No.
a
SCREW M2.5*3(NL)
86.ADWV5.001
b
SCREW M2.5*6(NL)
86.ADWV5.002
c
SCREW M2.5*10(NL)
86.ADWV5.003
d
SCREW M2.5*15(NL)
86.ADWV5.004
e
SCREW M2*2.2
86.ADWV5.005
f
SCREW M2*3-B (NL)
86.ADWV5.006
g
SCREW M2*3-S (NL)
86.ADWV5.007
h
SCREW M2*4
86.ADWV5.008
i
SCREW M3*4 (NL)
86.ADWV5.009
Chapter 3
55
Screws List
56
No.
Description
j
SCREW D-SUB 4#X40*1/5-NI (NL)
Part No.
86.ADWV5.010
Chapter 3
Disassembly Procedure
Removing the Battery Pack
1.
Slide the battery lock to the end as the arrow indicates.
2.
The battery pack will pop up then remove it.
Removing the HDD Module
1.
Release the two screws fastening the HDD module cover.
2.
Detach the HDD module cover.
3.
Pull the HDD module then lift the HDD module as the arrow indicates then detach the HDD
module.
Chapter 3
57
Removing the RAM Module/Mini PCI Card/Thermal Module/CPU
58
1.
Release the four screws holding the thermal module cover.
2.
Remove the thermal module cover.
3.
Pull the RAM module locks at the same time as the arrows indicate.
4.
The RAM module will pop up then detach it. Repeat the anterior step to remove another RAM
module.
5.
Pull the Mini PCI card locks at the same time as the arrows indicate.
6.
The Mini PCI card will pop up then detach it.
7.
Disconnect the auxiliary antenna cable (gray) and the main antenna cable (black).
Chapter 3
8.
Release the two screws securing the system fan.
9.
Disconnect the system fan cable carefully the remove the system fan.
10. Release the four screws securing the CPU heatsink.
11. Remove the CPU heatsink as the arrow indicates.
12. Counter clockwise release the screw securing the CPU using a flat head screw driver.
13. Carefully detach the CPU.
Chapter 3
59
Removing the ODD Module
If you just want to replace the ODD module, you do not have to remove the anterior components.
Please skip the anterior steps of disassembly. After you remove the battery pack and the thermal
module cover, follow the steps below.
60
1.
Release the screw securing the ODD module.
2.
Push the ODD module using a screwdriver as shown.
3.
Remove the ODD module from the main unit.
Chapter 3
Removing the LCD Module from the Main Unit
If you just want to replace or check the LCD module, you can skip all the main unit disassembly
procedures. After removing the battery pack, please follow the steps below.
1.
Open the notebook as shown.
2.
Remove the middle cover from the edge of the middle cover.
3.
Carefully detach the middle cover.
4.
Carefully disconnect the LCD cable.
5.
Slightly pull out the wireless antenna cables.
Chapter 3
61
6.
Release the two screws holding the LCD module on the bottom side of the main unit.
7.
Release the four screws securing the LCD hinges on the main unit.
8.
Then detach the LCD module from the main unit.
Removing the Keyboard
If you just want to replace the keyboard, skip the LCD module disassembly. After you remove the
middle cover, follow the steps below.
62
1.
Release the two screws securing the keyboard plate.
2.
Carefully detach the keyboard plate from the edge of the keyboard plate and place the
keyboard plate as shown.
3.
Release the keyboard FFC lock carefully because it is fragile. Then remove the keyboard plate.
Chapter 3
Disassembling the Main Unit
Separating the Upper Case and the Lower Case
1.
Carefully release the media board FFC lock because it is fragile. Then disconnect the media
board FFC.
2.
Release the 12 screws securing the upper case and the lower case on the bottom side.
3.
Release the four hexagonal screws securing the external VGA port and the DVI-D port.
4.
Release the two screws securing the upper case and the lower case on the upper side.
5.
Then detach the upper case from the main unit.
Chapter 3
63
Removing the Power Board and the Modem Board
64
1.
Detach the power board slightly.
1.
Release the two screws securing the modem board.
2.
Detach the modem board then disconnect the modem board cable.
Chapter 3
Removing the Main Board
1.
Disconnect the speakers cable and the microphone cable.
2.
Release the screw securing the main board.
3.
Slightly pull the edge of the lower case from the left side and at the same time push the main
board on the bottom side to pop up the main board.
4.
Repeat Step 3 from the rear side.
5.
Then detach the main board. If your system is equipped with Bluetooth module, please place
the main board on the lower case as shown. Do not abruptly remove the main board from the
lower case.
Chapter 3
65
Removing the Bluetooth Module
66
1.
Place the main board as shown.
2.
Tear off the tinsel.
3.
Disconnect the Bluetooth module cable and remove the main board.
4.
Remove the Bluetooth module.
Chapter 3
Removing the Speakers
1.
Release the two screws securing the speakers.
2.
Then detach the speakers.
Removing the Touch Pad Board
1.
Slightly unlock the touch pad FFC lock by nail and disconnect the touch pad FFC.
2.
Release the screw holding the touch pad board bracket then remove the touch pad board
bracket.
3.
Detach the touch pad board.
Chapter 3
67
Removing the VGA Heatsink
1.
Release the two screws securing the VGA heatsink.
2.
Then detach the VGA heatsink.
Disassembling the LCD Module
68
1.
Remove the four screw cushions on the LCD bezel then release the four screws holding the
LCD bezel.
2.
Carefully detach the LCD bezel from the LCD module.
3.
Tear off the tapes holding the LVDS cable and the LCD cable then release the two screws
securing the inverter board.
Chapter 3
4.
Carefully disconnect the LVDS cable.
5.
Carefully disconnect the LCD cable then remove the inverter board.
6.
Release the two screws securing the LCD panel.
7.
Then detach the LCD panel.
8.
Release the eight screws holding the left and right LCD brackets and remove the LCD
brackets.
Chapter 3
69
9.
Tear off the tape holding the LCD cable.
10. Carefully pull and disconnect the LCD cable.
70
Chapter 3
Chapter 4
Troubleshooting
Please use the following procedures as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options may occur errors or invalid responses.
1.
Obtain the detailed fail symptoms as many as possible.
2.
Verify the symptoms by attempting to recreate, running the diagnostic tests or repeating the
same operation.
Chapter 4
71
System Check Procedures
External Diskette Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or diskette. A
writable, diagnostic diskette is required.
NOTE: Make sure that the diskette does not have more than one label attached. Multiple labels may cause
damage to the drive or make the drive fail.
1.
Boot from the diagnostic diskette and start the diagnostic programs.
2.
See if FDD test is passed as the programs run the FDD test.
3.
Follow the instructions in the message window.
If errors occur with the internal diskette driver, reconnect the diskette connector on the system
board. If the errors still remain:
1.
Reconnect the external diskette drive.
2.
Replace the external diskette driver.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or CD-ROM.
NOTE: Make sure that the CD-ROM does not have any label attached. The label may cause damage to the
drive or make the drive fail.
1.
Boot from the diagnostic diskette and start the diagnostic programs.
2.
See if CD-ROM test is passed when the programs run the CD-ROM test.
3.
Follow the instructions in the message window.
If errors occur, reconnect the connector on the system board. If the errors still remain:
1.
Reconnect the external CD-ROM drive.
2.
Replace the external CD-ROM drive.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is under test. If the internal keyboard does
not work or an unexpected error appears, make sure that the flexible cable extending from the
internal keyboard is correctly connected on the system board. If the keyboard is correctly
connected, run the Keyboard test.
If errors occur, do the following procedures in sequence to correct the problems. Do not replace a
non-defective FRU.
1.
Reconnect the keyboard cable.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer.
72
Chapter 4
• Numeric keypad
• External keyboard
If any of these devices do not function, reconnect the cable and repeat the anterior procedures.
Memory Check
Follow the procedures below to correct the memory errors.
1.
Boot from the diagnostic diskette and start the diagnostic programs.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is correctly inserted into the connector. A wrong connection will cause
errors.
Power System Check
To verify the symptoms, power on the computer by using the following power sources separately.
1.
Remove the battery pack.
2.
Connect the power adaptor and check the power supply.
3.
Disconnect the power adaptor and install the battery pack, then check the power supply.
If you think there is a power supply problem, please go to “Check the Power Adaptor” and “Check
the Battery Pack” in this chapter.
Check the Power Adaptor
Unplug the power adaptor cable from the computer and measure the output voltage at the plug of
the power adaptor cable. See the illustration and follow the procedures below.
pin 1: +19V to +20.5V
pin 2: 0V, ground
1.
If the voltage is not correct, replace the power adaptor.
2.
If the voltage is within the range:
(1) Replace the system board.
(2) If the problem is still not resolved, see “Undetermined Problems”.
(3) If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adaptor does not always indicate a defect.
3.
If the power-on indicator does not light up, check the power cord of the power adaptor for
continuity and correct installation.
4.
If the operational charge does not work, see “Check the Battery Pack”.
Chapter 4
73
Check the Battery Pack
Follow the procedures below to check the battery pack.
From software, this helps to identify the problem is on recharging or discharging.
1.
Check the Power Management in Control Panel.
2.
Then confirm that the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the step 1 and step 2 for both battery and adaptor.
From hardware, this helps to identify whether you should replace the battery pack or not.
1.
Power off the system.
2.
Remove the battery pack and measure the voltage between terminals one (+) and seven (-).
There are seven terminals totally. See the illustration below.
3.
If the voltage is still less than 7.5V after recharging, replace the battery.
If the battery status indicator does not light up, remove the battery pack. After the battery pack
returns to room temperature, reinstall it to the system.
If the charge indicator does not light up, replace the battery pack. If the charge indicator still does
not light up, replace the AC/DC charger board.
Touchpad Check
If the touchpad does not work, follow the procedures one at a time to correct the problem. Do not
replace a non-defective FRU.
74
1.
Reconnect the touchpad cables.
2.
Replace the touchpad.
Chapter 4
3.
Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer
movement will occur when a slight, steady pressure is applied to the touchpad pointer. This
symptom is not a hardware problem.
Chapter 4
75
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes.
NOTE: Perform the FRU replacement or actions in the sequence shown in Error Message List, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
The error messages are listed in the coming pages to indicate the BIOS signals on the screen and
the error symptoms classified by functions. If the symptom is not included on the list, please refer to
Undetermined Problems.
NOTE: Most of the error messages occur during POST. Some of them show information about a hardware
device, for example, the size of memory installed. Others may indicate problems with a device, such
as the way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, please reset the computer.
Enter Setup and install Setup defaults to correct the errors.
Index of Error Messages
Error Code List
Error Code
006
Error Message
Equipment Configuration Error Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
The causes will be shown before Equipment Configuration Error.
010
Memory Error at xxxx:xxxx:xxxxh (R: xxxxh, W: xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
No error code
Battery critical low: In this situation BIOS will issue four short beeps
then shut down system, no message will be shown.
No error code
Thermal critical high: In this situation BIOS will shut down the system,
no message will be shown.
Error Message List
Error Message
Failure Fixed Disk
76
FRU/Action in Sequence
Reconnect hard disk drive connector.
Run Load Default Settings in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see Keyboard or Auxiliary Input Device Check.
Keyboard error
see Keyboard or Auxiliary Input Device Check.
Keyboard Controller Failed
see Keyboard or Auxiliary Input Device Check.
Keyboard locked - Unlock key
switch
Unlock external keyboard
Chapter 4
Error Message List
Error Message
FRU/Action in Sequence
Monitor type does not match
CMOS - Run Setup
Run Load Default Settings in BIOS Setup Utility.
Shadow RAM Failed at offset:
nnnn
BIOS ROM
System board
System RAM Failed at offset:
nnnn
DIMM
System board
Extended RAM Failed at offset:
nnnn
DIMM
System board
System battery is dead Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to
reconfigure system time, then reboot system.
System CMOS checksum bad Default configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Previous boot incomplete Default configuration used
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST
differed from CMOS
Run Load Default Settings in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type
in BIOS Setup Utility.
See External Diskette Drive Check.
Incorrect Drive A type - run
Setup
Check the drive is defined with the proper diskette type
in BIOS Setup Utility.
System cache error - Cache
disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Chapter 4
77
Error Message List
Error Message
78
FRU/Action in Sequence
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration
Data
BIOS ROM
System board
I/O device IRQ conflict
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are
properly identified.
Diskette drive
Hard disk drive
System board
No beep, power-on indicator
turns off and LCD is blank.
Power source (battery pack and power adapter). See
Power System Check.
Ensure every connector is connected correctly.
Reconnect the DIMM.
LED board
System board
No beep, power-on indicator
turns on and LCD is blank.
Power source (battery pack and power adapter). See
Power System Check.
Reconnect the LCD connector.
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator
turns on and LCD is blank. But
you can see POST on an
external CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator
turns on and a blinking cursor
shown on LCD during POST.
Ensure every connector is connected tightly and
correctly.
System board
No beep during POST but
system runs correctly.
Speaker
System board
Chapter 4
POST Code
Code
Beeps
For Boot Block in Flash ROM
E0h
Initialize the chipset.
E1h
Initialize the bridge.
E2h
Initialize the CPU.
E3h
Initialize the system timer.
E4h
Initialize system I/O.
E5h
Check force recovery boot.
E6h
Checksum BIOS ROM.
E7h
Go to BIOS.
E8h
Set Huge Segment.
E9h
Initialize Multi Processor.
EAh
Initialize OEM special code.
EBh
Initialize PIC and DMA.
ECh
Initialize Memory type.
EDh
Initialize Memory size.
EEh
Shadow Boot Block.
EFh
System memory test.
F0h
Initialize interrupt vectors.
F1h
Initialize Run Time Clock.
F2h
Initialize video.
F3h
F4h
Initialize System Management Mode.
1
Output one beep before boot.
F5h
Boot to Mini DOS.
F6h
Clear Huge Segment.
F7h
Boot to Full DOS.
Chapter 4
79
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom/Error
Action in Sequence
LCD backlight doesn't work.
LCD is too dark.
LCD brightness cannot be adjusted.
LCD contrast cannot be adjusted.
Enter BIOS Utility to execute Load Setup Default
Settings, then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key do
not work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or vertical
lines displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom/Error
Indicator incorrectly
remains off or on, but
system runs correctly.
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom/Error
80
Action in Sequence
Power shuts down during
operation.
Power source (battery pack and power adapter). See Power
System Check.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power
on.
Power source (battery pack and power adapter). See Power
System Check.
Battery pack
Power adapter
Hard drive & battery connection board
System board
Chapter 4
Power-Related Symptoms
Symptom/Error
Action in Sequence
The system doesn’t
power-off.
Power source (battery pack and power adapter). See Power
System Check.
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged.
See Check the Battery Pack.
Battery pack
System board
PCMCIA-Related Symptoms
Symptom/Error
Action in Sequence
System cannot detect the
PC Card (PCMCIA).
PCMCIA slot assembly
System board
PCMCIA slot pin is
damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size)
appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute Load Default Settings,
then reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom/Error
Action in Sequence
In Windows, multimedia
programs, no sound
comes from the computer.
Audio driver
Speaker
System board
Internal speakers make
noise or emit no sound.
Speaker
System board
Power Management-Related Symptoms
Symptom/Error
Action in Sequence
The system will not enter
hibernation.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system does not
enter hibernation mode
and four short beeps
every minute.
Press Fn + F4 and see if the computer enters hibernation
mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
Chapter 4
81
Power Management-Related Symptoms
Symptom/Error
Action in Sequence
The system does not
enter standby mode after
closing the LCD.
LCD cover switch
System board
The system does not
resume from hibernation
mode.
Hard disk connection board
Hard disk drive
System board
The system does not
resume from standby
mode after opening the
LCD.
LCD cover switch
System board
Battery fuel gauge in
Windows does not go
higher than 90%.
Remove battery pack and let it cool for two hours.
Refresh battery (continue to use battery until power off, then
charge battery).
Battery pack
System board
System hangs
intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom/Error
Action in Sequence
System configuration
does not match the
installed devices.
Enter BIOS Setup Utility to execute Load Default Settings,
then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not
work correctly.
Press Fn + F5, LCD/CRT/Both display switching
System board
USB does not work
correctly.
System board
Print problems
Ensure the Parallel Port in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port
device problems.
Ensure the Serial Port in the Devices Configuration” of BIOS
Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom/Error
Keyboard (one or more
keys) does not work.
82
Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board
Chapter 4
Keyboard/Touchpad-Related Symptoms
Symptom/Error
Touchpad does not work.
Action in Sequence
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom/Error
Internal modem does not
work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
NOTE: If you can not correct the problems according to the anterior tables, see Undetermined Problems.
Chapter 4
83
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do
with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU
replacement should be considered only when a recurring problem exists.
When analyzing an intermittent problems, follow the procedures below:
84
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which devices fail, which devices are incorrectly
installed, whether a short circuit happens, or whether the system is inoperative.
NOTE: Verify if all devices attached are supported by the computer.
NOTE: Verify if the power supply used at the time of failure is operating correctly. You can refer to “Power
System Check”.
Follow the procedures below to isolate the failing FRU. Do not isolate non-defective FRU.
1.
Power off the computer.
2.
Visually check the devices. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
• Non-Acer devices
• Printer, mouse, and other external devices
• Battery Pack
• Hard disk drive
• DIMM
• CD-ROM / Diskette drive module
• PC cards
4.
Power on the computer.
5.
Determine if the problem has been resolved.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the
failed FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective
FRU.
• System board
• LCD assembly
Chapter 4
85
Chapter 5
Jumper and Connector Location
Main Board
Top Side
Chapter 5
86
87
#
Item
#
Item
1
JP1
LCD PANEL CONNECTOR
Description
2
JP2
LED BOARD CONNECTOR
Description
3
JP3
MDC CONNECTOR
4
JP5
MEDIA BOARD CONNECTOR
5
JP6
TOUCH PAD BOARD
CONNECTOR
6
JP7
INTERNAL KEYBOARD
CONNECTOR
7
JP9
PCMCIA SOCKET
8
JP12
INTERNAL SPEAKER
CONNECTOR
9
JP13
INTERNAL MIC CONNECTOR
10
U12
LAN CHIP
11
U14
1349 CHIP
12
U17
BIOS FLASH ROM
13
U18
SOUTH BRIDGE CHIP
14
U25
SUPER I/O
15
U27
EC/KBC CHIP
16
U30
CARD BUS CONTROLLER
17
U33
AUDIO CODEC
Chapter 5
Bottom Side
#
Item
Description
#
Item
Description
1
JP14
USB CONNECTOR
2
JP15
CRT CONNECTOR
3
JP16
TV-OUT CONNECTOR
4
JP17
MINI CARD CONNECTOR
5
JP18
DDRII SODIMM SLOT
6
JP19
DDRII SODIMM SLOT
7
JP20
FAN CONNECTOR
8
JP21
USB CONNECTOR
9
JP22
RJ45 CONNECTOR
10
JP23
CPU SOCKET
11
JP24
ODD CONNECTOR
12
JP25
5-in-1 CONNECTOR
13
JP27
HDD (PATA) CONNECTOR
14
JP28
MINI PCI SLOT
15
JP30
NEW CARD SOCKET
16
JP31
BLUETOOTH CONNECTOR
17
JP32
SPDIF OUT JACK
18
JP33
LINE-IN JACK
Chapter 5
88
#
89
Item
Description
#
Item
Description
19
JP34
MIC JACK
20
PJP1
DC JACK
21
PJP2
BATTERY PACK CONNECTOR
22
U39
NORTH BRIDGE
Chapter 5
Switch Board
Top Side
Item
Description
SW1
POWER BUTTON
SW2
E-MAIL BUTTON
SW3
INTERNAL BUTTON
SW4
USER BUTTON
SW5
EMPOWER BUTTON
D1
POWER LED
D2
MEDIA LED
D3
CAPS LED
D4
NUMLK LED
D5
EMAIL LED
Chapter 5
90
Bottom Side
Item
91
Description
JP2
USB CONNECTOR
JP3
USB CONNECTOR
JP7
LED BOARD
CONNECTOR
Chapter 5
Clear CMOS
You can short JOPEN1 jump on the main board to erase CMOS data. Please refer to the images
below for the location of JOPEN1 jump.
Chapter 5
92
Chapter 6
FRU (Field Replacement Unit) List
This chapter offers the FRU (Field Replacement Unit) list in global configuration of Aspire 5110/
5100/3100 series. Refer to this chapter whenever you order the parts to repair or for RMA (Return
Merchandise Authorization).
Please note that when ordering FRU parts, you should check the most up-to-date information
available on your regional web or channel. For whatever reasons a part number is changed, it will
NOT be noted on the printed service guide. For Acer authorized service providers, your Acer office
may have a different part number code from those given in the FRU list of this printed service
guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for
service.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose them properly, or follow the rules set by your regional Acer office on
how to return it.
Chapter 6
93
Parts
Category
Partname
Acer Part Number
ADAPTER
N/A
ADAPTER 65W 3PIN LITEON PA-1650-02LR
AP.06503.012
ADAPTER 65W 3PIN DELTA SADP-65KB DBFF
AP.06501.009
ADAPTER 90W 3PIN LITEON PA-1900-04LR
AP.09003.006
ADAPTER 90W 3PIN DELTA ADP-90SB BBAC
AP.09001.009
ADAPTER 90W 3PIN LI SHIN SLS0202C19A20LF
AP.09006.004
BATTERY LI-ION 4 CELLS 2000MAH SONY
BT.00404.008
BATTERY
BATTERY LI-ION 4 CELLS 2000MAH SANYO
BT.00403.008
BATTERY LI-ION 4 CELLS 2000MAH PANASONIC
BT.00405.006
BATTERY LI-ION 6 CELLS 4000MAH SANYO
BT.00603.017
BATTERY LI-ION 6 CELLS 4000MAH PANASONIC
BT.00605.004
BATTERY LI-ION 6 CELLS 4000MAH SONY
BT.00604.008
BATTERY LI-ION 8 CELLS 4800MAH SONY
BT.00804.012
BATTERY LI-ION 8 CELLS 4800MAH SANYO
BT.00803.015
MODEM BOARD FOXCONN T60M845.02 SV92A1Z (AC97/
Azalia)
54.ABHV5.001
BLUETOOTH MODULE FOXCONN T60H928.01 (Broadcom
BCM2045)
54.ABHV5.002
MINI PCI WIRELESS BOARD FOXCONN (ATHEROS)
802.11b/g T60N874.03 (AR2414/AR5413 solution)
54.ABHV5.003
MINI PCI WIRELESS BOARD FOXCONN (BROADCOM)
802.11b/g T60H906.00 (BCM4318 solution)
54.ABHV5.004
MINI WLAN (NAVARRO DISCRETE) FOXCONN
(ATHEROS) 802.11 a/b/g T60H921.10 (AR5424 solution)
54.ABHV5.005
MINI WLAN (NAVARRO DISCRETE) FOXCONN
(BROADCOM) 802.11b/g T60H938.03 (4311)
54.ABHV5.006
BOARD
N/A
N/A
94
N/A
TV TUNER M103 SW Analog(DVB-T)-Hybird
55.A61V5.007
N/A
TV TUNER M104 H/W Analog
55.A61V5.004
N/A
TV TUNER M115 DTV H/W Analog-Hybird
55.A61V5.005
N/A
MEDIA BOARD
55.ADWV5.001
Chapter 5
Category
N/A
N/A
Partname
Acer Part Number
SWITCH BOARD-W/TV AS
55.ADWV5.003
SWITCH BOARD-W/O TV TM/AS
55.ABHV5.001
INVERTER BOARD - 15 IN.
19.ABHV5.001
INVERTER BOARD - 15.4 IN.
19.ABHV5.002
TP FPC- T/P TO MB
50.ABHV5.001
RJ-11 CABLE
50.ABHV5.002
BLUETOOTH CABLE
50.ABHV5.003
CABLE
N/A
N/A
TV TUNER CABLE (TV/T-MB CABLE)
50.ABHV5.004
N/A
CABLE - 3.5 PHONE JACK TO PAL TV
50.A61V5.013
N/A
7 PIN MINI-DIN S-VIDEO TO 4 CABLE
50.A61V5.011
N/A
PAL TO NTSC CONNECTOR
20.A61V5.001
N/A
PAL-NTSC DVB-T ANT
50.A61V5.014
N/A
LCD WIRESET-15.4 IN.
50.ABHV5.008
N/A
LCD WIRESET-15 IN.
50.ABHV5.007
N/A
LCD WIRESET-15.4 IN.
50.ABHV5.008
N/A
POWER CORD US 3 PIN
27.TAVV5.001
N/A
POWER CORD EU 3 PIN
27.TAVV5.002
N/A
POWER CORD AUS 3 PIN
27.TAVV5.003
N/A
POWER CORD UK 3 PIN
27.TAVV5.004
N/A
POWER CORD CHINA 3 PIN
27.TAVV5.005
N/A
POWER CORD SWISS 3 PIN
27.TAVV5.006
N/A
POWER CORD ITALIAN 3 PIN
27.TAVV5.007
N/A
POWER CORD DENMARK 3 PIN
27.TAVV5.008
N/A
POWER CORD JP 3 PIN
27.TAVV5.009
N/A
POWER CORD SOUTH AFRICA 3 PIN
27.TAVV5.010
N/A
POWER CORD KOERA 3 PIN
27.TAVV5.011
POWER CORD
N/A
POWER CORD ISRAEL 3 PIN
27.TAVV5.012
N/A
POWER CORD INDIA 3 PIN
27.TAVV5.013
N/A
POWER CORD TWN 3 PIN
27.TAVV5.014
CASE/COVER/BRACKET ASSEMBLY
MIDDLE COVER AS
Chapter 5
42.ABHV5.001
95
Category
Acer Part Number
UPPER CASE AS W/O TV & MEDIA B
60.ABHV5.001
N/A
UPPER CASE AS W/O TV W/MEDIA B
60.ADWV5.001
N/A
UPPER CASE AS W/TV & MEDIA B
TBD
LOWER CASE W/SPEAKER MIC W/OTV W/DVI &FIR&1394
60.ADWV5.002
LOWER CASE W/SPEAKER MIC W/O TV & DVI & 1394
&FIR
60.ABHV5.002
THERMAL DOOR
42.ABHV5.002
T/P BRACKET
33.ABHV5.001
OPTICAL BRACKET
33.ABHV5.002
OPTICAL BEZEL GBASE - SUPER MULTI
42.ABHV5.003
OPTICAL BEZEL GBASE - DVD/CDRW
42.ABHV5.005
HDD DOOR AS
42.ABHV5.004
HDD BRACKET
33.ABHV5.003
LCD COVER 15 IN. WITH LOGO W/ANTENNA
60.ABHV5.003
LCD BEZEL W/LOGO- 15 IN.
60.ABHV5.004
LCD BRACKET SET ( R&L ) - 15IN
6K.ABHV5.001
N/A
N/A
N/A
96
Partname
Chapter 5
Category
Partname
Acer Part Number
N/A
LCD COVER 15.4 IN. WITH LOGO W/ANTENNA
60.ABHV5.005
N/A
LCD BEZEL - 15.4 TEXTURE
60.ABHV5.006
N/A
LCD BRACKET SET ( R&L ) - 15.4
6K.ABHV5.002
COMMUNICATION MODULE
N/A
WIRELESS ANTENNA 15 IN.
50.ABHV5.005
N/A
WIRELESS ANTENNA 15.4 IN.
50.ABHV5.006
N/A
CPU AMD TURION 64 256K+256K 1.6G TMDTL50HAX4CT
KC.TTL02.500
N/A
CPU AMD TURION 64 512K+512K 1.6G TMDTL52HAX5CT
KC.TTL02.520
N/A
CPU AMD TURION 64 512K+512K 1.8G TMDTL56HAX5CT
KC.TTL02.560
N/A
CPU AMD TURION 64 512K+512K 2.0G TMDTL60HAX5CT
KC.TTL02.600
N/A
CPU AMD SEMPRON 512K 1.6G SMS3200HAX4CM
KC.S3202.25F
N/A
CPU AMD SEMPRON 256K 1.8G SMS3400HAX3CM
KC.S3402.25F
N/A
CPU AMD SEMPRON 512K 1.8G SMS3500HAX4CM
KC.S3502.25F
DVD/CDRW 24X COMBO MODULE
6M.ABHV5.001
N/A
"DVD/CDRW COMBO 24X DRIVE LITEON SSC2485K.GBASE,LF,EMI*2"
KO.02409.022
N/A
"DVD/CDRW COMBO 24X DRIVE PHILIPS SCB5265
,GB,LF FW#TX13"
KO.02408.011
N/A
DVD SUPER MULTI MODULE
6M.ABHV5.002
N/A
"DVD SUPER MULTI PIONEER DVR-K16RS,BASE"
KU.00805.029
N/A
"DVD SUPER MULTI PANASONIC UJ-850B,GBASE,LF"
KU.00807.025
N/A
"DVD SUPER MULTI HLDS GMA-4082N, GBASE, LF"
KU.0080D.021
N/A
"DVD SUPER MULTI PHILIPS SDVD8821,GBASE,LF"
KU.00809.005
CPU/PROCESSOR
COMBO DRIVE
HDD/HARD DISK DRIVE
HDD PATA 40G 4200RPM SEAGATE N2.2 ST9402112A
(RohS)
KH.04001.019
N/A
HDD PATA 40G 4200RPM HGST HAKONE A
HTS421240H9AT00 (ROHS)
KH.04007.013
N/A
HDD PATA 40G 5400RPM WD ML40 WD400UE-22HCT0
(ROHS)
KH.04008.025
N/A
HDD PATA 60G 5400RPM SEAGATE MERRCURY2
ST96812A (RohS)
KH.06001.007
N/A
HDD PATA 60G 5400RPM TOSHIBA TAURUS MK6034GAX
(Rohs)
KH.06004.007
Chapter 5
97
Category
Partname
Acer Part Number
N/A
HDD PATA 60G 5400RPM HGST MORAGA+
HTS541060G9AT02 (RohS)
KH.06007.011
N/A
HDD PATA 80 5400RPM SEAGATE Merrcury 2 ST98823A
(RohS)
KH.08001.022
N/A
HDD PATA 80G 5400RPM TOSHIBA Ares-B
KH.08004.006
N/A
HDD PATA 80G 5400RPM HGST MORAGA+
HTS541080G9AT00 (RohS) F/W: A60A
KH.08007.013
N/A
HDD PATA 80G 5400RPM WD ML40 WD800-22HCT0(Rohs)
KH.08008.027
N/A
HDD PATA 100G 5400RPM SEAGATE Mercury 2
ST9100824A (RohS)
KH.10001.007
N/A
HDD PATA 100G 5400RPM TOSHIBA Ares-B MK1032GAX
(RohS)
KH.10004.002
N/A
HDD PATA 100G 5400RPM HGST Moraga+
HTS541010G9AT00 (RohS) FW:A60A
KH.10007.004
N/A
HDD PATA 100G 5400RPM WD ML60
KH.12001.024
N/A
HDD PATA 120G 5400RPM SEAGATE Merrcury 2
ST9120821A(RohS)
KH.12004.002
N/A
HDD PATA 120G 5400RPM TOSHIBA Taurus
MK1234GAX(Rohs)
KH.1200B.001
N/A
HDD SATA 80G 5400RPM SEAGATE Mercury 2 ST98823AS
KH.08001.023
N/A
HDD SATA 80G 5400RPM TOSHIBA Aries-B MK8032GSX
KH.08004.005
N/A
HDD SATA 80G 5400RPM HGST Moraga+B
HTS541080G9SA00
KH.08007.015
N/A
HDD SATA 100G 5400RPM SEAGATE Mercury 2
ST9100824AS FW:3.06
KH.10001.008
N/A
HDD SATA 100G 5400RPM TOSHIBA Aries-B MK1032GSX
F/W: AS021G
KH.10004.003
N/A
HDD SATA 100G 5400RPM HGST Moraga+B
HTS541010G9SA00 FW:S60D
KH.10007.005
N/A
HDD SATA 100G 5400RPM SAMSUNG M60S HM100JI
KH.1000B.003
N/A
HDD SATA 120G 5400RPM SEAGATE Mercury 2
ST9120821AS
KH.12001.025
N/A
HDD SATA 120G 5400RPM TOSHIBA Taurus
MK1234GSX(Rohs)
KH.12004.003
N/A
HDD SATA 120G 5400RPM SAMSUNG M60S HM120JI
KH.1200B.002
KEYBOARD CHINESE W/MEDIA B AS
TBD
N/A
KEYBOARD THAILAND W/MEDIA B AS
TBD
N/A
KEYBOARD HEBREW W/MEDIA B AS
TBD
N/A
KEYBOARD ARABIAN W/MEDIA B AS
TBD
N/A
KEYBOARD US INTERNATIONAL W/MEDIA B AS
TBD
N/A
KEYBOARD RUSSIA W/MEDIA B AS
TBD
N/A
KEYBOARD GREEK W/MEDIA B AS
TBD
N/A
KEYBOARD CZECH REPUBLIC W/MEDIA B AS
TBD
N/A
KEYBOARD UK W/MEDIA B AS
TBD
KEYBOARD
98
Chapter 5
Category
Partname
Acer Part Number
N/A
KEYBOARD SWEDEN W/MEDIA B AS
TBD
N/A
KEYBOARD FRENCH W/MEDIA B AS
TBD
N/A
KEYBOARD PORTUGUESE W/MEDIA B AS
TBD
N/A
KEYBOARD HOLLAND W/MEDIA B AS
TBD
N/A
KEYBOARD CROATIA W/MEDIA B AS
TBD
N/A
KEYBOARD SLOVENIA W/MEDIA B AS
TBD
N/A
KEYBOARD SLOVAK W/MEDIA B AS
TBD
N/A
KEYBOARD BRAZIL PORTUGES W/MEDIA B AS
TBD
N/A
KEYBOARD SWISS/G W/MEDIA B AS
TBD
N/A
KEYBOARD DENMARK W/MEDIA B AS
TBD
N/A
KEYBOARD ITALIAN W/MEDIA B AS
TBD
N/A
KEYBOARD BELGIUM W/MEDIA B AS
TBD
N/A
KEYBOARD GERMAN W/MEDIA B AS
TBD
N/A
KEYBOARD CANADA FRANCH W/MEDIA B AS
TBD
N/A
KEYBOARD NORWAY W/MEDIA B AS
TBD
N/A
KEYBOARD HUNGARY W/MEDIA B AS
TBD
N/A
KEYBOARD SPANISH W/MEDIA B AS
TBD
N/A
KEYBOARD LATIN W/MEDIA B AS
TBD
N/A
KEYBOARD ICELANDIC W/MEDIA B AS
TBD
N/A
KEYBOARD TURKEY W/MEDIA B AS
TBD
N/A
KEYBOARD JAPAN W/MEDIA B-AS
TBD
N/A
KEYBOARD CHINESE W/O MEDIA B AS
KB.ASP07.001
N/A
KEYBOARD THAILAND W/O MEDIA B AS
KB.ASP07.003
N/A
KEYBOARD HEBREW W/O MEDIA B AS
KB.ASP07.023
N/A
KEYBOARD ARABIAN W/O MEDIA B AS
KB.ASP07.018
N/A
KEYBOARD US INTERNATIONAL W/O MEDIA B AS
KB.ASP07.002
N/A
KEYBOARD RUSSIA W/O MEDIA B AS
KB.ASP07.014
N/A
KEYBOARD GREEK W/O MEDIA B AS
KB.ASP07.021
N/A
KEYBOARD CZECH REPUBLIC W/O MEDIA B AS
KB.ASP07.012
N/A
KEYBOARD UK W/O MEDIA B AS
KB.ASP07.005
N/A
KEYBOARD SWEDEN W/O MEDIA B AS
KB.ASP07.015
N/A
KEYBOARD FRENCH W/O MEDIA B AS
KB.ASP07.007
N/A
KEYBOARD PORTUGUESE W/O MEDIA B AS
KB.ASP07.011
N/A
KEYBOARD HOLLAND WO /MEDIA B AS
TBD
N/A
KEYBOARD CROATIA W/O MEDIA B AS
KB.ASP07.140
N/A
KEYBOARD SLOVENIA W/O MEDIA B AS
KB.ASP07.139
N/A
KEYBOARD SLOVAK W/O MEDIA B AS
TBD
N/A
KEYBOARD BRAZIL PORTUGES W/O MEDIA B AS
KB.ASP07.019
N/A
KEYBOARD SWISS/G W/O MEDIA B AS
KB.ASP07.008
N/A
KEYBOARD DENMARK W/O MEDIA B AS
KB.ASP07.017
N/A
KEYBOARD ITALIAN W/O MEDIA B AS
KB.ASP07.006
N/A
KEYBOARD BELGIUM W/O MEDIA B AS
KB.ASP07.009
N/A
KEYBOARD GERMAN W/O MEDIA B AS
KB.ASP07.004
Chapter 5
99
Category
Partname
Acer Part Number
N/A
KEYBOARD CANADA FRANCH W/O MEDIA B AS
KB.ASP07.020
N/A
KEYBOARD NORWAY W/O MEDIA B AS
KB.ASP07.016
N/A
KEYBOARD HUNGARY W/O MEDIA B AS
KB.ASP07.013
N/A
KEYBOARD SPANISH W/O MEDIA B AS
KB.ASP07.010
N/A
KEYBOARD LATIN W/O MEDIA B AS
TBD
N/A
KEYBOARD ICELANDIC W/O MEDIA B AS
TBD
N/A
KEYBOARD TURKEY W/O MEDIA B AS
KB.ASP07.022
N/A
KEYBOARD JAPAN W/O MEDIA B-AS
TBD
ASSY LCD MODULE 15 IN. XGA W/ANTENNA
6M.ABHV5.003
LCD 15 IN. XGA AUO B150XG02. V4 LEAD-FREE
LK.15005.010
N/A
LCD 15 IN. XGA SAMSUNG LTN150XB-L03-V
LK.15006.008
N/A
LCD 15 IN. XGA LPL LP150X08-TLA2 LF
LK.15008.019
N/A
LCD 15 IN. XGA QDI QD150XL06-03-01
LK.15009.008
N/A
LCD 15 IN. XGA CMO N150X3-L09 Rev. C1
LK.1500D.013
N/A
ASSY LCD MODULE 15.4 IN. WXGA GLARE W/ANTENNA
6M.ABHV5.004
N/A
ASSY LCD MODULE 15.4 IN. WXGA NON-CLARE W/
ANTENNA
TBD
N/A
LCD 15.4 WXGA QDI QD15TL07-01 NON-GLARE LF
LK.15409.008
N/A
"LCD 15.4 IN. WXGA QDI QD15TL07-02,GLARE LF 16MS"
LK.15409.009
N/A
"LCD 15.4 WXGA SAMSUNG LTN154XA-L01-0 100 25MS
L6-G5 NON-GLARE,16MS 200 nits"
LK.15406.016
N/A
"LCD 15.4 IN. WXGA SAMSUNG LTN154XA-L01-G
GLARE,200NITS,16MS "
LK.15406.017
N/A
LCD 15.4 IN. WXGA LPL LP154W01-TLD1 GLARE 16MS
LK.15408.018
N/A
LCD 15.4 WXGA LPL LP154W01-TLE1 TLA1 NON-GLARE
16MS 200nits V - Cut LF
LK.15408.019
N/A
LCD 15.4 IN. WXGA LPL LP154W01-TLB6 GLARE 16MS
TBD
N/A
LCD 15.4 WXGA CMO N154I2-L01 16MS NON-GLARE LF
LK.1540D.011
N/A
LCD 15.4 WXGA CMO N154I2-L02 GLARE 16MS
LK.1540D.012
N/A
LCD 15.4 IN. WXGA AUO B154EW02 V.0 16MS NONGLARE LF
LK.15405.013
N/A
LCD 15.4 IN. WXGA AUO B154EW02 V.1 GLARE 16MS
LK.15405.014
N/A
LCD RUBBER
47.ABHV5.001
N/A
LATCH RUBBER
47.ABHV5.002
N/A
LCD SCREW MYLAR
47.ABHV5.003
LCD
MISCELLANEOUS
100
Chapter 5
Category
Partname
Acer Part Number
N/A
RUBBER FOOT - LARGE
47.ABHV5.004
N/A
RUBBER FOOT - SMALL
47.ABHV5.005
N/A
NAME PLATE - AS3100
40.ABJV5.001
N/A
NAME PLATE - AS5100
40.ABHV5.001
N/A
NAME PLATE - AS5110
40.ADWV5.001
MAINBOARD M52P64MB DISCRETE PATA 10/100 W/CARD
READER W/O MEDIA
MB.ABJ02.001
N/A
MAINBOARD M52P128MB SATA GLAN W/CARD READER
W/O TV
MB.ADW02.002
N/A
MAINBOARD M56P128MB SATA GLAN W/CARD READER
W/O TV
MB.ADW02.001
N/A
MAINBOARD UMA PATA 10/100 W/CARD READER W/O
TV/FIR/1394
MB.ABE02.001
MAINBOARD
PCMCIA SLOT/PC CARD SLOT
N/A
PCMCIA SOCKET
20.ABHV5.001
MEMORY 256MB DDR II 533 NANYA NT256T64UH4A1FN37B
KN.25603.029
N/A
MEMORY 256MB DDR II 533 MICRON MT4HTF3264HY53EB4
KN.25604.030
N/A
MEMORY 256MB DDR II 533 SAMSUNG M470T3354CZ3CD5
KN.2560B.017
N/A
MEMORY 256MB DDR II 533 HYNIX HYMP532S64BP6-C4
KN.2560G.012
N/A
MEMORY 512MB DDR II 533 NANYA NT512T64UH8A1FN37B
KN.51203.023
N/A
MEMORY 512MB DDR II 533 SAMSUNG M470T6554CZ3CD5
KN.5120B.015
N/A
MEMORY 512MB DDR II 533 HYNIX HYMP564S64BP6-C4
KN.5120G.013
N/A
MEMORY 1G DDR II 533 INFINEON HYS64T128021HDL3.7-B (.09u)
KN.1GB02.030
N/A
MEMORY 1G DDR II 533 NANYA NT1GT64U8HA0BN-37B
KN.1GB03.006
FAN ASSY - DISCRETE
23.ADWV5.001
FAN ASSY - UMA
23.ABHV5.001
MEMORY
FAN
N/A
HEATSINK
Chapter 5
101
Category
Partname
Acer Part Number
CPU THERMAL MODULE-DIS
60.ABHV5.009
VGA HEATSINK-DISCRETE
34.ADWV5.001
POINTING DEVICE
TOUCHPAD W/SPONGE
56.ADWV5.001
SPEAKER SET (R&L)
23.ADWV5.002
MIC
23.ADWV5.003
N/A
REMOTE CONTROLLER - FORMASA MP-RC802
RT.8020A.001
N/A
MCE REMOTE CONTROLLER-SMK
LC.MCE05.001
N/A
MCE REMOTE CONTROLLER RECEIVER-SMK
LC.MCE05.002
N/A
MCE IR BLASTER-SMK
LC.MCE05.003
N/A
SCREW M2.5*3(NL)
86.ADWV5.001
N/A
SCREW M2.5*6(NL)
86.ADWV5.002
N/A
SCREW M2.5*10(NL)
86.ADWV5.003
N/A
SCREW M2.5*15(NL)
86.ADWV5.004
N/A
SCREW M2*2.2
86.ADWV5.005
N/A
SCREW M2*3-B (NL)
86.ADWV5.006
N/A
SCREW M2*3-S (NL)
86.ADWV5.007
N/A
SCREW M2*4
86.ADWV5.008
N/A
SCREW M3*4 (NL)
86.ADWV5.009
N/A
SCREW D-SUB 4#X40*1/5-NI (NL)
86.ADWV5.010
SPEAKER
N/A
ACCESSORY
SCREW
102
Chapter 5
Exploded Diagram
No.
Description
Acer Part Number
001
MIDDLE COVER AS
42.ABHV5.001
002
LOWER CASE W/SPEAKER MIC W/OTV W/DVI &FIR&1394
60.ADWV5.002
004
HDD DOOR AS
42.ABHV5.004
251
MAINBOARD M52P64MB DISCRETE PATA 10/100 W/CARD
READER W/O MEDIA
MB.ABJ02.001
252
SWITCH BOARD-W/TV AS
55.ADWV5.003
253
UPPER CASE AS W/O TV & MEDIA B
60.ABHV5.001
301
THERMAL DOOR
42.ABHV5.002
304
CPU THERMAL MODULE-DIS
60.ABHV5.009
305
FAN ASSY - DISCRETE
23.ADWV5.001
308
SCREW M2*3-S (NL)
86.ADWV5.007
309
SCREW M2.5*10(NL)
86.ADWV5.003
310
SCREW M2.5*15(NL)
86.ADWV5.004
Chapter 5
103