Acer 530 Laptop User Manual

Acer TravelMate 530 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PART NO.: VD.T24V5.001
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate 530 service guide.
Date
II
Chapter
Updates
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
Chapter 1
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Left Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Right Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Lock Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Embedded Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
The Euro Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Launch Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
E-Mail Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Chapter 2
System Utilities
35
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
System Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
System Diagnostic Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Running Diagnostics Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Chpater 3
Machine Disassembly and Replacement
53
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Removing the HDD Module/Memory/FDD Module/Optical Module and the CPU58
Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the Optical Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the FDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Removing the Keyboard, the Memory, the Modem Card,
the LCD Module and the Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Removing the Memory, the Modem Card (Bluetooth Card)
and the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Removing the Switch Board and the LCD module . . . . . . . . . . . . . . . . . . .62
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
VII
Table of Contents
Separate the main unit into the logic upper
and the logic lower assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Disassembling the logic lower assemby . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Disassembling the Logic Upper Assembly . . . . . . . . . . . . . . . . . . . . . . . . .64
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Disassembling the External Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Disassembling the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Disassembling the Floppy Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . .67
Disassembling the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . .67
Chapter 4
Troubleshooting
69
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
External CD-ROM/DVD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . .70
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . .71
Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Display Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Sound Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Index of AFlash BIOS Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Chapter 5
Jumper and Connector Locations
85
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
SW3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
SW2 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Chapter 6
FRU (Field Replaceable Unit) List
Appendix A
Model Definition and Configuration
89
108
TravelMate 530 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Appendix B
Test Compatible Components
111
Microsoft® Windows® XP Home Environment Test . . . . . . . . . . . . . . . . . . . . .112
Microsoft® Windows® XP Pro Environment Test . . . . . . . . . . . . . . . . . . . . . . .115
Microsoft® Windows® 2000 Environment Test . . . . . . . . . . . . . . . . . . . . . . . .118
Appendix C
Index
VIII
Online Support Information
121
123
Chapter 1
System Specifications
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
Mobile Intel® Pentium®4 processor-M at 1.8GHz or higher
T
Built-in 0.13 micron technology; includes 512KB L2 cache; supports Enhanced Intel®
SpeedStepTM technology; 400MHz processor system bus
T
Standard 256MB DDR-266 SDRAM, upgradeable up to 1GB on dual SoDIMM sockets
T
Integrated 24x CD-ROM/8x DVD-ROM or 24/10/8/24x DVD/CD-RW combo drive
T
20/30/40GB or higher-capacity Ultra DMA-100HDD
T
High-capacity, Enhanced-IDE hard disk
T
Li-Ion main battery pack
T
Power management system with ACPI (Advanced Configuration Power Interface) 2.0 supporting
Standby and Hibernation power saving modes
T
Thin-Film Transistor (TFT) liquid-crystal display (LCD) displaying 32-bit high true colour up to
1024X768 eXtended Graphics Array (XGA) resolution for 14.1”/15.0” (specification varies
depending on models)
T
3D capabilities
T
Shared Memory Architechure (Intel DVMT-Dynamic Video Memory Technology)
T
Simultaneous display on LCD and CRT
T
Support S-video(NTSC/PAL) TV-out
T
“Automatic LCD dim” feature that automatically decides the best settings for your display and
conserves pwer
T
Dual view suupport
Display
Multimedia
T
16-bit high-fidelity AC’97 stereo audio
T
Built-in dual speakers
T
Built-in microphone
T
High-speed optical drive
Connectivity
Chapter 1
T
High-speed fax/data modem port
T
Ethernet/Fast Ethernet port
T
USB (Universal Serial Bus) ports
T
IEEE 1394 port
T
Optional Invilink 802.11b wireless LAN
T
Optional Integrated Bluetooth module
1
Keyboard and Pointing Device
T
5 Launch keys, including Internet Browser and email and 3 user-programmable keys
T
4-way scroll button
T
Sleek, smooth and stylish design
T
Full-sized keyboard
T
Ergonomically-centered touchpad pointing device
Expansion
T
Two type II or one type III cardBus PC Card slots
T
Upgradeable memory
T
Two Type II or One Type III PCMCIA Cardbus sockets
T
One RJ-11 jack for 56Kbps fax/modem
T
One RJ-45 jack for LAN
T
One DC-in jack for AC adapter
T
One ECP/EPP compliant 25-pin parallel port
T
One external 15-pin VGA port
T
One speaker/headphone/line-out jack
T
One microphone/line-in jack
T
Three USB 2.0 ports
T
One IEEE 1394 port
T
One S-video (NTSC/PAL) output port
T
One Kensignton lock socket
T
FIR (Fast Infred) port
T
One 100-pin docking connector
I/O Ports
2
Chapter 1
System Block Diagram
Fan Control
Mobile P4
CPU Bypass
& CPUVID
page 3
Clock Generator
Thermal Sensor
ADM1032AR
uFCBGA-479/uFCPGA-478 CPU
page 5
CY28346
page 3,4,5
page 12
page 3
HA#(3..31)
HD#(0..63)
System Bus
400MHz
CRT Conn
page 14
DVOC
TV ENCODER
CH7011
page 14
DDR-SO-DIMM X2
BANK 0, 1, 2, 3 page 10,11
VGA Embeded
732 pin u-FCBGA
page 15
TV-OUT Conn
Memory BUS(DDR)
MONTARA-GML
LCD Conn
2.5V DDR- 200/266
page6,7,8,9
page 15
HUB LINK 1.5
5 IN 1
CARDREADER
USB conn
USB
PCI BUS
3.3V 33 MHz
IDSEL:AD19
(PIRQD#,GNT#3,REQ#3)
IEEE 1394
VT6307L
Mini PCI
socket
page 24
page 20
IDSEL:AD16
(PIRQA#,GNT#0,REQ#0)
LAN
RTL 8100BL
ICH4-M
IDSEL:AD20
(PIRQE/F#,GNT#2,REQ#2)
AC-LINK
page 23
page 15,16,17
ENE CB1420
Primary IDE
HDD
Connector
Secondary IDE
CDROM
Connector
page 19
page 21
IDSEL:AD22/23
(PIRQG/H#,GNT#1/4,REQ#1/4)
RJ45/11 CONN
page 19
Slot 1
page 22
Slot 0
MDC/BT
CONN
AC-LINK CONN
page 23
BGA 421 pin
CardBus Controller
page 26
page 29
page 18
LPC BUS
SPR
CONN
page 22
page 18
Power On/Off
Reset & RTC
SMsC
LPC47N227
page 30
LPC to X-BUS
Super I/O
EC
NS87591L
DC/DC Interface
Suspend
page 31
page 27
page 27
Touch Pad
Int.KBD
page 26
EC I/O Buffer
Power Circuit
DC/DC
page 29
page 28
BIOS
PARALLEL
page 26
page 28
page 25
FDD
page 26
*RJ45/11 CONN
*PS2 x2 CONN
*CRT CONN
*LINE IN JACK
*LINE OUT JACK
*MIC JACK
*DC JACK
*TVOUT CONN
*PRINTER PORT
*COM PORT
*USB CONN x1
FIR
page 25
page
32,33,34,35,36,37
Chapter 1
3
Board Layout
Top View
4
1
USB Connector Port
13
Modem Connector
2
USB Connector Port
14
IEEE 1394 Connector
3
USB Connector Port
15
RJ11 Connector
4
TV-Out Connector
16
Battery Connector
5
Panel Connector
17
MDC Connector
6
RJ45 Connector Port
18
DDR 200Pin Port
7
Panel Backlight On/Off Switch
19
Northbridge
8
LPTCN-27 Port
20
Internal Keyboard Connector
9
Switch Buttom Interface Connector
21
Southbridge
10
SPR Connector
22
Audio Board to Main Board Connector
11
CRT Connector Port
23
Mini PCI Connector
12
DC Jack Port
24
System On/Off Button
Chapter 1
Bottom View
1
HDD Connector
5
PCMCIA Connector 84Pin Port
2
Card Reader Connector
6
CPU FAN Connector
3
FDD Connector
7
CPU Socket
4
DDR 200Pin So-Dimm Connector
8
CD-ROM Port
Chapter 1
5
Outlook View
A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.
Front View
#
Icon
1
1
Item
Description
Display screen
Also called LCD (liquid-crystal display),
displays computer output.
2
Launch keys
Special keys for launching Internet
browser, E-mail program and frequently
used programs. Located at the top of the
keyboard are five buttons. They are
designated as P1, P2, P3, E-mail button
and Web browser button. P1, P2 and P3
launch user-programmable applications; Email and Web browser launch E-mail and
Internet browser applications.
3
Power Switch
Turns on the computer power.
4
Touchpad
Touch-sensitive pointing device which
functions like a computer mouse.
5
Click buttons (left,
center and right)
The left and right buttons function like the
left and right mouse buttons; the center
button serves as a 4-way scroll button.
6
Floppy disk drive (or
Reads/writes data from/to the media.
card reader if installed)
7
Floppy eject button
Ejects floppy disk.
8
Speakers
Outputs sound.
9
Palmrest
Comfortable support area for your hands
when you use the computer.
Outputs sound.
10
6
Keyboard
Inputs data into your computer.
Chapter 1
11
Status indicators
LEDs (light-emitting diode) that turn on and
off to show the status of the computer, its
functions and components.
12
Locking Latch
Slide locking mechanism secures the lid
when the computer is not in use.
Chapter 1
7
Left Panel
#
Icon
Item
Description
1
Optical drive
Houses an optical drive module (CD-ROM,
DVD-ROM or DVD/CD-RW combo drive).
2
Optical drive indicator
Lights up when the optical drive is active.
3
Eject button
Ejects the drive tray.
4
Emergency eject slot
Ejects the drive tray when the computer is
turned off. There is a mechanical eject button on the optical drive. Simply insert the tip
of a pen or paperclip and push to eject the
tray.
8
Chapter 1
Right Panel
#
Chapter 1
Icon
Item
Description
1
Microphone/Line-in
jack
Accepts audio line-in devices (e.g.,
microphone, audio CD player, stereo
walkman).
2
Headphone/Speaker/
Line-out jack
Connects to audio line-out devices (e.g.,
headphones, speakers).
3
PC card eject buttons
Eject the PC Card from the slot.
4
PC card slots
Accepts two Type II or one TypeIII PC
cards.
5
Modem jack
Connects to a phone line.
6
IEEE 1394 port
Connects to an IEEE device.
7
Infrared port
Interfaces with infrared devices (e.g.,
infrared printer, IR-aware computer.)
9
Rear Panel
#
10
Icon
Item
Description
1
Security keylock
Connects to a Kensington-compatible
computer security lock.
2
Power jack
Connects to an AC adapter.
3
External display port
Connects to a display device (e.g., external
monitor, LCD projector).
4
Expansion port
Connects to I/O port replicator or EasyPort
expansion devices.
5
Parallel port
Connects to a parallel device (e.g., parallel
printer).
6
Network jack
Connects to an Ethernet 10/100-based
network.
7
S-video
Connects t a television or display device
with S-video input.
8
USB port
Connects to Universal Serial Bus devices
(e.g., USB mouse, USB camera).
Chapter 1
Bottom Panel
#
1
Icon
Item
Cooling fan
Description
Helps keep the computer cool.
Note: Don’t cover or obstruct the opening
of the fan.
Chapter 1
2
Battery bay
3
Battery release latches Unlatches the battery to remove the battery
pack.
Houses the computer’s battery pack.
4
Hard disk bay
Houses the computer’s hard disk.
5
Memory compartment
Houses the computer’s main memory.
11
Indicators
The computer has seven easy-to-read status icons below the display screen.
The status LCD displays icons that show the status of the computer and its components.
Icon
Function
Description
Power
Lights green when the computer is on and
lights orange when the computer is in
Standby mode.
Media activity
Lights when the hard disk is active.
Battery charge
Lights green when the battery is being
charged.
Lights orange when the battery power is
low and is being charged.
12
Wireless
communication
Lights when the Wireless LAN capabilities
are enabled.
Caps lock
Lights when Caps Lock is activated.
Num lock
Lights when Num Lock is activated.
Scroll lock
Lights when Scroll Lock is activated.
Chapter 1
Lock Keys
The keyboard has three lock keys which you can toggle on and off.
Lock Key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed
are in uppercase.
Num lock
(Fn-F11)
When Num Lock is on, the embedded keypad is in
numeric mode. The keys function as a calculator
(complete with the arithmetic operators +, -, *, and /).
Use this mode when you need to do a lot of numeric
data entry. A better solution would be to connect an
external keypad.
Scroll lock
(Fn-F12)
When Scroll Lock is on, the screen moves one line up
or down when you press w and y respectively.
Scroll Lock does not work with some applications.
Chapter 1
13
Embedded Numeric Keypad
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired Access
Number keys on embedded
keypad
Cursor-control keys on
embedded keypad
Main keyboard keys
14
Num Lock On
Num Lock Off
Type numbers in a normal
manner.
Hold j while using
cursor-control keys.
Hold Fn while using cursorcontrol keys.
Hold Fn while typing letters
on embedded keypad.
Type the letters in a normal
manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Windows logo
key
Icon
Description
Start button. Combinations with this key perform
special functions. Below are a few examples:
+ Tab (Activates next taskbar button)
+ E (Explores My Computer)
+ F (Finds Document)
+ M (Minimizes All)
j + Windows logo key + M (Undoes Minimize All)
+ R (Displays the Run... dialog box)
Application
key
Chapter 1
Opens a context menu (same as a right-click).
15
Hot Keys
The computer uses hotkey or key combinations to access most of the computer’s controls like sreen
brightness, volume output.
To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination.
Hot Key
Icon
Function
Description
Fn-F1
Hot key help
Displays help on hot keys.
Fn-F2
System Property
Displays the System Property.
Fn-F3
Power Options
Display the Power Options Properties used by the
computer (function available if supported by operating
system).
Fn-F4
Sleep
Puts the computer in Sleep mode.
See “Power management” on page 25.
See “Power management” on page 25.
16
Fn-F5
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-F6
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-F7
Touchpad toggle
Turns the internal touchpad on and off.
Fn-F8
Speaker toggle
Turns the speakers on and off.
Fn-w
Volume up
Increases the speaker volume.
Chapter 1
Hot Key
Icon
Function
Description
Fn-y
Volume down
Decreases the speaker volume.
Fn-x
Brightness up
Increases the screen brightness.
Fn-z
Brightness down
Decreases the screen brightness
Chapter 1
17
The Euro Symbol
If your keyboard layout is set to United States-International or United Kingdom or if you have a keyboard with a
European layout, you can type the Euro symbol on your keyboard.
NOTE: For US keyboard users: The keyboard layout is set when you first set up Windows. For the Euro
symbol to work, the keyboard layout has to be set to United States-International.
To verify the keyboard type in Windows 2000, follow the steps below:
1.
Click on Start, Settings, Control Panel.
2.
Double-click on Keyboard.
3.
Click on the Language tab.
4.
Verify that keyboard layout used for En English (United States)” is set to United States-International. If not,
select and click on Properties; then select United States-International and click on OK.
5.
Click on OK.
To verify the keyboard type in Windows XP, follow the steps below:
1.
Click on Start, Control Panel.
2.
Double-click on Regional and Language Options.
3.
Click on the Language tab and click on Details.
4.
Verify that the keyboard layout used for "En English (United States)" is set to United States-International.
If not, select and click on ADD; then select United States-International and click on OK.
5.
Click on OK.
To type the Euro symbol:
1.
Locate the Euro symbol on your keyboard.
2.
Open a text editor or word processor.
3. Hold Alt Gr and press the Euro symbol.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
18
Chapter 1
Launch Keys
Located at the top of keyboard are five buttons. These buttons are called launch keys. They are designated as
P1, P2, P3 Email button and Web browser button.
NOTE: To the left of these five launch keys is the wireless communication button. This wireless
communication button works for model with 802.11b wireless LAN only.
Launch Key
Default application
P1
User-programmable
P2
User-programmable
P3
User-programmable
Email
Email application
Web browser
Internet browser application
Chapter 1
19
E-Mail Detection
Click right button at the Launch Manager icon on the taskbar and click on E-Mail Detection. In this dialog box,
you have the option to enable/disable mail checking, set the time interval for mail checking, etc. If you already
have an email account, you can fill in User Name, Password and POP3 Server in the dialog box. The POP3
Server is the mail server where you get your email.
Aside from the email checking function, there is a mail button that is used to launch the email application. It is
located above the keyboard right below the LCD.
20
Chapter 1
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor
responds as you move your finger on the surface of the touchpad. The central location on the palmrest
provides optimal comfort and support.
NOTE: If you are using an external USB mouse, you can press Fn-F7 to disable the touchpad.
Touchpad Basics
The following teaches you how to use the touchpad:
T
Move your finger across the touchpad to move the cursor.
T
Press the left (1) and right (3) buttons located on the edge of the touchpad to do selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad produces similar results.
T
Use the 4-way scroll (2) button (top/bottom/left/and right) to scroll.
Function
Left Button
Right Button
Scroll Button
Tap
Execute
Click twice
quickly
Tap twice (at the same
speed as double-clicking
the mouse button)
Select
Click once
Tap once
Drag
Click and hold,
then use finger
to drag the
cursor on the
touchpad
Tap twice (at the same
speed as double-clicking
a mouse button) then hold
finger to the touchpad on
the second tap to drag the
cursor
Access context
menu
Chapter 1
Click once
21
Function
Scroll
Left Button
Right Button
Scroll Button
Tap
Click and hold
the button in the
desired
direction (up/
down/left/right)
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movements. Hence, the lighter the touch, the better the response.
Tapping too hard will not increase the touchpad’s responsiveness.
22
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
Intel Mobile Pentium 4-M/Mobile Pentium-4 Celeron
CPU package
/ µ FC-PGA package
CPU core voltage
1.3/1.2
BIOS
Item
Specification
BIOS vendor
Phoenix
BIOS Version
1.00
BIOS ROM type
Flash ROM
BIOS ROM size
512KB
BIOS package
TSOP
Supported protocols
ACPI 1.0b,PC Card 95, SM BIOS 2.3, EPP/IEEE 1284, ECP/IEEE 1284
1.7 & 1.9, PCI 2.2, PnP 1.0a, DMI 2.0, PS/2 keyboard and mouse, USB,
VGA BIOS, CD-ROM bootable,
BIOS password control
Set by setup manual
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
512KB
1st level cache control
Always enabled
2st level cache control
Always enabled
Cache scheme control
Fixed in write-back
System Memory
Item
Specification
Memory controller
Memory size
128/256/512MB
DIMM socket number
2 sockets
Supports memory size per socket
512MB
Supports maximum memory size
1G (by two 512MB SO-DIMM module)
Supports DIMM type
DDR Synchronous DRAM
Supports DIMM Speed
133 MHz
Supports DIMM voltage
2.5V
Supports DIMM package
200-pin soDIMM
Memory module combinations
You can install memory modules in any combinations as long as they
match the above specifications.
Chapter 1
23
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
128MB
128MB
0MB
256MB
256MB
0MB
512MB
512MB
128MB
128MB
256MB
128MB
256MB
384MB
128MB
512MB
640MB
256MB
128MB
384MB
256MB
256MB
512MB
256MB
512MB
768MB
512MB
128MB
640MB
512MB
256MB
768MB
512MB
512MB
1024MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. .
LAN Interface
Item
Specification
Supports LAN protocol
10/100 Mbps
LAN connector type
RJ45
LAN connector location
Rear side
Modem Interface
Item
Specification
Data modem data baud rate (bps)
56K
Supports modem protocol
V.90/192 MDC
Modem connector type
RJ11
Modem connector location
Right side
Floppy Disk Drive Interface
Item
Vendor & model name
Specification
Panasonic JU226A273FC/Mitsumi D353G-2938
Floppy Disk Specifications
Media recognition
2DD (720KB)
2HD (1.2MB, 3-mode)
2HD (1.44MB)
Sectors/track
9
15
18
Tracks
80
80
80
Rotational speed (RPM)
300
360
300
Read/write heads
2
Encoding method
MFM/FM
Power Requirement
Input Voltage (V)
24
+5V +/- 10%
Chapter 1
Hard Disk Drive Interface
Item
Specification
Vendor &
Model Name
IBM 20G
IBM 30G
IBM 40G
Toshiba
20G
(MK2018
)GAP
Toshiba
30G
(MK3021
)GAS
Toshiba
40G
(MK4021
)GAS
Hitachi
20G
DK23EA
-20F
Hitachi
30G
DK23EA
-30F
Hitachi
40G
DK23EA
-40F
Capacity (MB)
20000
30000
40000
20000
30000
40000
20000
30000
40000
Bytes per
sector
512
512
512
512
512
512
512
512
512
Data heads
2
3
4
2
3
4
2
3
4
Disks
1
2
2
1
2
2
1
2
2
Spindle speed
(RPM)
4200
RPM
4200
RPM
4200
RPM
4200
RPM
4200
RPM
4200
RPM
4200
RPM
4200
RPM
4200
RPM
Drive Format
Performance Specifications
Buffer size
2048KB
2048KB
2048KB
2048KB
2048KB
2048KB
2048KB
2048KB
2048KB
Interface
ATA-5
ATA-5
ATA-5
ATA-5
ATA-5
ATA-5
ATA-5
ATA-5
ATA-5
Max. media
transfer rate
(disk-buffer,
Mbytes/s)
216
287
287
235
Data transfer
rate
(host~buffer,
Mbytes/s)
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
100 MB/
Sec.
Ultra
DMA
mode-5
5V(DC)
+/- 5%
5V(DC)
+/- 5%
5V(DC)
+/- 5%
5V(DC)
+/- 5%
5V(DC)
+/- 5%
5V(DC)
+/- 5%
5V(DC)
+/- 5%
5V(DC)
+/- 5%
DC Power Requirements
Voltage
tolerance
5V(DC)
+/- 5%
DVD-ROM Interface
Item
Vendor & model name
Specification
Toshiba SD-C2612
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (KB/sec)
Sustained:
Max 3.6Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Data Buffer Capacity
128 KBytes
Interface
IDE/ATAPI
Applicable disc format
DVD: DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18),DVD-R (read, single
border)
CD: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, CD-I, CDI Bridge (Photo-CD, Video-CD) Multisession CD (Photo-CD, CD-EXTRA, CD-R,
CD-RW), CD-R (read), CD-RW (read)
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
Chapter 1
+5 V +/- 5 % (Operating)
+/- 8 % (Start up)
25
Audio Interface
Item
Specification
Audio Controller
Integrated Software Audio in ICH4-M South Bridge with Realtek ALC201
AC97 Codec(No SPDIF)
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
20 bit stereo Digital to analog converter
18 bit stereo Analog to Ditial converter
Compatibility
Microsoft PC98/PC99, AC97 2.1
Mixed sound source
Line-in, CD, Video, AUX
Voice channel
8/16-bit, mono/stereo
Sampling rate
44.1 KHz
Internal microphone
No
Internal speaker / Quantity
Yes/2
Supports PnP DMA channel
DMA channel 00
Supports PnP IRQ
IRQ3, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11
Video Interface
Item
Specification
Chip vendor
Intel
Chip name
Integrated VGA chip in Montara_GML North Birdge
Chip voltage
Core/3.3V
Supports ZV (Zoomed Video) port
No
Video Resolutions Mode (for both LCD and CRT)
16 bits
(High color)
Resolution
32 bits
(True color)
800x600
Yes
Yes
1024x768
Yes
Yes
1152x864
Yes
Yes
1280x1024
Yes
Yes
1400x1050
(SXGA+panel only)
Yes
Yes
Parallel Port
Item
Parallel port controller
26
Specification
SMSC LPC47N227
Number of parallel port
1
Location
Rear side
Connector type
25-pin D-type connector, in female type
Parallel port function control
Enable/Disable/Auto (BIOS or operating system chooses
configuration) by BIOS Setup
Note: Depending on your operating system, disabling an unused
device may help free system resources for other devices.
Chapter 1
Parallel Port
Item
Specification
Supports ECP/EPP/Bi-directional (PS/2
compatible)
Yes (set by BIOS setup)
Note: When Mode is selected as EPP mode, “3BCh” will not be
available.
Optional ECP DMA channel (in BIOS Setup)
DMA channel 1
Optional parallel port I/O address (in BIOS
Setup)
378h, 278h, 3BCH
Optional parallel port IRQ (in BIOS Setup)
IRQ7, IRQ5
USB Port
Item
Specification
USB Compliancy Level
2.0
OHCI
USB 1.1
Number of USB port
3
Location
Rear side
Serial port function control
Enable/Disable by BIOS Setup
PCMCIA Port
Item
Specification
PCMCIA controller
ENE CB1420 CardBus controller
Supports card type
Type-III/II
Number of slots
One type-III or Two type-II
Access location
Right panel
Supports ZV (Zoomed Video) port
No ZV support
Supports 32 bit CardBus
Yes (IRQ11)
System Board Major Chips
Item
Controller
System core logic
Intel Montara GML+ICH4-m
Super I/O controller
SMC LPC47N227
Audio controller
Integrated Software Audio in Intel ICH4-m South Bridge with Realtek
ALC202 AC97 Codec(No SPDIF)
Video controller
Integrated VGA chip in Intel Montara-GML North Birdge
Hard disk drive controller
ICH4-m
Keyboard controller
NS PC87591L K/B controller
RTC
ICH4-m
Keyboard
Item
Specification
Keyboard controller
NS PC87591L K/B controller
Keyboard vendor & model name
Chicony
Total number of keypads
87/88/89 keys with 101/102 key emulation
Windows logo key
Yes
Internal & external keyboard work simultaneously
Yes
Chapter 1
27
Battery
Item
Specification
Vendor & model name
Panasonic
Battery Type
Li-ion
Pack capacity
63.6Wh
Cell voltage
3.7V/cell
Number of battery cell
8
Package configuration
4 cells in series, 2 series in parallel
Package voltage
14.8V
LCD Inverter Specification
This inverter is designed to light up the CCFL of LCD for TravelMate 530 series notebook. It should be
supported the following LCD panels.
No.
28
Supplier
Model
Type
1
LG
LP150x04
TFT, 15.0” XGA
2
Hitachi
TX38D85
TFT, 15.0” XGA
3
AU
CLAA141XF ∅ 1
TFT, 14.1” XGA
4
CPT
CLAA150PA01
TFT, 15.0” SXGA+
5
IBM
ITSX95C
TFT 15.0” SXGA+
Chapter 1
Electrical Characteristics
No
.
1
Parameter
Input
Symbol
NV_PWR
Min.
9
Typ.
14.8
Max.
21
Unit
V
voltage
Comment
7.5V (continuous) can
work
*Note 1
2
Input
Iin
--
0.33
--
A
IL
3.0
--
6.8
mA
current
3
Lamp
current
4
Lamp
DAC=0V
* Note 2
IL
2.7
--
6.3
mA
DAC=1V
* Note 3
current
4
Frequency
F
45
55
65
KHz
5
Output
power
Pout
--
--
4.5
W
6
Efficiency
η
80%
--
--
--
7
Starting
voltage
Vs
1600
--
---
V
8
Starting
time
Tvs
1
--
1.5
Sec
9
Dispoff#
At 0’C
2.8
3.3
3.6
V
Backlight on/off signal
0
0.5
0.8
V
Low level
3.3
V
*Note 2
150
158
Hz
PWM signal frequency
3.0
3.3
3.6
V
PWM signal amplitude
30
--
100
%
10
Limited
lamp
maximum
current
DACBRIG
0
11
PWM
signal
*Note 4
INV_PW
M
142
Ton
Duty = ------------------Period
12
Lamp
current
over-shoot
13
Current
Waveform
factor
I zero-PK
--
--
1.27
10
%
1.56
Multiple
Unbalance
Rate
I−p
2
Ip
or
I rms
14
Line transient (10.8V to
21V/100us) and turn on
transient
-10%
0
+10%
Mulitple
--
--
0
A
I rms
*10
Ip −I−p
Irms
15
Chapter 1
Turn off
current
(Hight
side)
IHL
PWM=30%
29
Electrical Characteristics
No
.
Parameter
Symbol
Min.
Typ.
Max.
Unit
Comment
15
Turn off
voltage
(Low side)
Voff
--
--
150VpP
V
PWM=30%
16
Voltage
Rise time
(Low side)
Trise
--
--
300us
us
PWM=30%
17
Voltage fall
time (Low
side)
Tfall
--
--
300us
us
PWM=30%
NOTE: Please pay attention to the fellowing:
*1. The inverter can work in 7.5V input voltage (continuous), but 7.5V electronic characteristic will not be care.
(Note: the display must be normal and can not glitter or become dark.)
*2. Limited lamp maximum current by DAC_BRIC signal:
When DAC_BRIG voltage is 0V and INV_PWM enables (100%), lamp has max. current.
When DAC_BRIG voltage is 3.3V and INV_PWM enables (100%), lamp has min. current.
When add 1V DAC, the 100% Lamp current will decrease 0.5mA.
DAC_BRIG signal comes from system chipset with internal resistance of 3K Ω
*3. Inverter operating frequency should be within specification (45~65kHz) at max. and min. brightness load.
*4. INV_PWM enable implies INV_PWM signal is High level (On duty cycle is 100%). It is a square wave of
150Hz to adjust backlight brightness that is a function of PWM duty cycle. Backlight brightness is maximum
value under INV_PWM at 100% and brightness is minimum under INV_PWM at 30%.
*5.The system interface signals belong to 3.3V.
*6. Please make sure open lamp output voltage should be within starting voltage specification.
*7. Inverter should pass human body safety test.
*8. Inverter should be no smoking by any component open/short test.
*9. Transformer voltage stress should not be over 85% under any condition.
(turn on overshoot transient and line transient.)
*10. Audio noise should be less than 36dB at 10cm distance.
.
Electrical specification
No
.
1
Symbol
V oper*
Min.
--
Typ.
650
Max.
--
Unit
Vrms
Comment
Lamp operating voltage
(650+/-50)
Il
6.2
6.5
6.8
mArms
DAC_BRIG: 0V,
PWM:100%
Il
3.07
3.3
3.6
mArms
DAC_BRIG: 0V,
PWM:30%
Il
5.7
6.0
6.3
mArms
DAC_BRIG: 0V,
PWM:100%
Il
2.7
3.0
3.3
mArms
F
45
55
65
kHz
η
80%
--
--
--
DAC_BRIG: 0V,
PWM:30%
30
Chapter 1
Thermal
All components on inverter board should follow below rules:
1. Component using conditions (component stress) must be within component specification including voltage
rating, current rating, temperature etc.
2. Component temperature shold follow below:
∆T <=30 Celsius degrees, at 25, 35 Celsius degrees.
T
Component temperature should be less than 70 Celsius degrees inside system at 35 Celsius degrees.
AC Adapter
T
Item
Vendor & model name
Specification
ADAPTER ASTEC SA80-3115-0583 and Liteon PA-1750-02CA
Input Requirements
Maximum input current (A,
@90Vac, full load)
1.2 Arms
0.6 Arms
@ 90V
@ 265V
Nominal frequency (Hz)
47 - 63
Frequency variation range (Hz)
47 - 63
Nominal voltages (Vrms)
90 - 265
Inrush current
The maximum inrush current will be less than 50A and 100A when the adapter
is connected to 115Vac(60Hz) and 230Vac(50Hz) respectively.
Efficiency
It should provide an efficiency of 84% minimum, when measured at maximum
load under 115V(60Hz).
Output Ratings (CV mode)
DC output voltage
19.0V including the effects of line voltage variation, load current, ripple and
noise
Noise + Ripple
300mvp-pmax (20MHz bandwidth) for resistor load
Output current
0 A (min.)
3.5A (max.)
Output Ratings (CC mode)
DC output voltage
19.0
Constant output
3.68A
Dynamic Output Characteristics
Start-up time
3 sec. (@115Vac)
Hold up time
6 ms min. (@120 Vac input, full load)
Over Voltage Protection (OVP)
27 V
Short circuit protection
Output can be shorted without damage, and auto recovery
Electrostatic discharge (ESD)
15kV (at air discharge)
8kV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
4242 Vdc for 1 second
Leakage current
250uA max at 250Vrms
Regulatory Requirements
1. FCC class B requirements(USA)
2. VDE class B requirements(German)
3. VCCI classII requirements(Japan)
System Power Management
ACPI mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned off
completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be power
managed in this state.
Chapter 1
31
ACPI mode
Power Management
Standby (S1)
CPU in Stop Clock state
VGA Standby, turn off back-light
PCMCIA Standby
Audio Power Down
Hard Disk Spin Down motor
Super I/O Power down
Suspend to RAM (S3)
CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4)
Also called Hibernate state. System saves all system states and
data onto the disk prior to power off the whole system.
Environmental Requirements
Item
Specification
Temperature
Operating
+5~+35°C
Non-operating
-20~+50°C
Non-operating
-20~+50°C (storage package)
Humidity
Operating
10% to 90% RH, non-condensing
Non-operating
10% to 90% RH, non-condensing (unpacked)
Non-operating
10% to 90% RH, non-condensing (storage package)
Vibration
Operating (unpacked)
5~500Hz: 1.0G
Non-operating (unpacked)
50~500Hz: 2.16G
Mechanical Specification
Item
32
Specification
Dimensions
322mm (W) x 272mm (D) x 35.5/38.0 mm(H) for 14.1 LCD model
327mm (W) x 272mm (D) x 38.0/39.3mm (H) for 15.0 inch model
Weight
6.5lb (including HDD, CD-ROM, FDD) for 14.1 inch model
7.0lb (including HDD, CD-ROM, FDD) for 15.0 inch model
I/O Ports
1 parallel port (25 pins) EPP/ECP capability, 1 CRT port (15 pins) supports DDC
2B, 1 TV-out connector, 1 microphone-in port, 1 headphone-out with SPDIF port,
1 AC adapter jack (2 pins), 1 type III or 2 type II PCMCIA card bus slots, 3 USB
2.0 ports (4 pins), 1 RJ-11/RJ-45 port
Drive Bays
One
Material
Plastic PC+ABS (Bayer OM105Q)
Indicators
Power, Media activity, Battery charge, Wireless communication, Caps lock, Num
lock and Scroll lock indicators
Switch
Power switch
Lid switch
Internet switch
Wireless Bluetooth Modem ON/OFF switch
E-mail switch
Chapter 1
Memory Address Map
Memory Address
00100000h-000F0000h
Size
Function
64KB
System BIOS
000CD000h-000C0000h
VGA BIOS
000C0000h-000A0000h
128 KB
Video memory (VRAM)
000A0000h-00000000h
640KB
Conventional memory
I/O Address Map
I/O Address
Function
000-00F
DMA controller-1
020-021
Interrupt controller-1
040-043
Timer 1
060, 064
Keyboard controller 38859 chip select
061
System speaker out
040B
DMA controller-1
061
System speaker
070-071
Real-time clock and NMI mask
080-08F
DMA page register
0A0-0A1
Interrupt controller-2
0C0-0DF
DMA controller-2
0F0-0FF
Numeric data processor
170-177
2nd EIDE device (CD-ROM) select
1F0-1F7
1st EIDE device (hard drive) select
220-22F
Audio
240-24F
Audio (optional)
278-27F
Parallel port 3
378,37A
Paraller port 1
3B0-3BB
3C0-3DF
Video Controller
3F0h-3F7
Standard Floppy Disk Controller
3F0-3F7
Floppy disk controller
480-48F, 4D6
DMA controller-1
4D0-4D1
CF8-CFF
PCI configuration register
IRQ Assignment Map
Interrupt Channel
IRQ00
Function(Hardware)
System timer
IRQ01
Keyboard
IRQ02
Programmable Interrup Controller
IRQ03
FIR
IRQ04
Communications Port (COM1)
IRQ05
Free
IRQ06
Standard Floppy Disk Controller
IRQ07
Free
IRQ08
Real Time Clock
IRQ09
ACPI Compliment System
IRQ10
SMBUS Controller
IRQ11
Free
Chapter 1
33
IRQ Assignment Map
Interrupt Channel
Function(Hardware)
IRQ12
PS2 Mouse
IRQ13
Numeric Data Processor
IRQ14
Primary IDE Controller (hard disk)
IRQ15
Secondary IDE Controller (CD-ROM drive)
IRQ16
USB Host Controller/”VIA 1394/ Montara-GML VGA Controller
IRQ17
AC97 Modem/AC97 Audio/USB Host Controller
IRQ18
Free
IRQ19
RealTek Lan/USB Host Controller
IRQ20
Carbus Controller 0
IRQ21
Carbus Controller 1
IRQ22
Wireless Lan 802.11
DMA Channel Assignment
DMA Channel
34
Function (Hardware)
00
ECP Printer Port
01
Standard Floppy Disk Controller
02
Fir
03
Direct Memory Controller
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup; press <C> to boot from CD-ROM; press <F12> to change boot device.
Chapter 2
35
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press por q.
T
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
This menu provides you the information of the system.
36
Chapter 2
Info.
Parameter
Description
Floppy Disk Drive
Shows floppy drive type informaiton.
Serial Number
This field displays the serial number of this unit.
UUID Number
UUID=32bytes
Chapter 2
37
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
NOTE: The screen above is for reference only. Actual values may differ.
38
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Date
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory
Shows the VGA memory size. The default value
is set to 16MB
Option:1/4/8/16/32MB
Quiet Boot
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Internal Hard Disk
Shows the hard disk types and capacity. If there
is no hard disk present or unknown type, “None”
should be shown on this field, otherwise the
capacity must be shown.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Auto or Both
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
LCD Auto Dim
Determines if the system will automatically dim
the LCD brightness in order to save power when
AC is not present.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
39
System Devices
The System Devices screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
40
Description
Options
Internal Touchpad
Determines whether or not to disable the internal
pointing device as the PS/2 mouse is connected.
Both or Auto
Infrared Port (FIR)
Enables, disables or auto detects the infrared port.
Enabled/Disabled/Auto
Parallel Port
Enables, disables or auto detects the parallel port.
Enabled/Disabled/Auto
Mode
Sets the operation mode of the parallel port.
ECP, EPP, Normal or Bi-directional
Base I/O address
Sets the I/O address of the parallel port. This
parameter is enabled only if Mode is set to ECP or
Bi-directional.
378h/278h
Interrupt
Sets the interrupt request of the parallel port.
IRQ7 or IRQ5
DMA Channel
Sets a DMA channel for the printer to operate in
ECP mode. This parameter is enabled only if Mode
is set to ECP.
DMA3 or DMA1
Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
User Password is
Shows the setting of the uer password.
Clear or Set
Supervisor Password is
Shows the setting of the administrator
password
Clear or Set
Set User Password
Press Enter to set the user password. When
set, this password protects the BIOS Setup
Utility from unauthorized access.
Set Supervisor Password
Press Enter to set the administrator password.
When set, this password protects the BIOS
Setup Utility from unauthorized access.
Password on boot
Allows the user to specify whether or not a
password is required to boot.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
Chapter 2
41
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
4.
Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
3.
Removing a Password
Follow these steps:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
42
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
Chapter 2
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2
43
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
44
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
Parameter
Exit Saving Changes
Description
Exit System Setup and save your changes to CMOS.
Exit Discarding Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
45
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
New features or options
T
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the Phlash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The Phlash utility has auto-execution function.
System Diagnostic Diskette
This diagnostic diskette is for the Acer TravelMate 530 series notebook machine. You can find the utility in
Service CD kit. It provides the following functions:
1.
BIOS Re-flash
2.
Serial port, parallel port and FDD test
3.
CMOS RTC and FDD Test
4.
Thermal Test
5.
Config Test
6.
1394ID Check
7.
Touchpad Test
8.
VGA R.G.B. Mode Test
9.
FAN Test
10. Keyboard Test
11. 32bit Systemcard Test
12. Audio Test
13. Battery Charge Test
To use the diagnostic programs, and system utilities, first create a bootable diskette. Then copy the files under
the following directory: Model1/field/files/Diagnostic Utility on this service CD. After you copy all files under the
Diagnostic Utility folder, then boot the system from the diagnostic diskette you create. Important! 1.) Please
insert this service CD as you use the diagnostic diskette. 2.) Please insert a music CD when you go through
Audio Test. Play the music CD during the test to see if the speaker emits sounds or not.
NOTE: This program contains a readme.txt file. This readme.txt file will introduce each test utility and its
functions.
IMPORTANT: 1The diagnostics program we use for TravelMate 530 series is not exactly the same as PQA
(Product Quality Assurance), the diagnostic program we used to employ in other model. The system
diagnostic utilities is provided by Acer Headquarters. You can utilize it as a basic diagnostic tool. To
1
46
New added description. Please pay attention to it.
Chapter 2
get this program, find it in the TravelMate 530 series service CD kit. To better fit local service
requirements, your regional office MAY have other diagnostic program. Please contact your regional
offices or the responsible personnel/channel to provide you with further technical details.
NOTE: For ASSY Function Test Procedure, please prepare the following items for system components test:
SIO/PIO loopback, diskette, mouse (PS/2), CD-Disk (Test Program), battery pack, SYS_card (Card
Bus)X2, AC-adapter, keyboard, external speaker and feather.
Chapter 2
47
Running Diagnostics Program
1.
BIOS Re-flash
Insert CD-Disk and floppy disk then boot from floppy disk drive to BIOS re-flash.
2.
Serial Port, Parallel Port and FDD Test
Insert SIO/PIO loopback to serial/parallel port. Place the diskette in the floppy diskette drive. Then run the test
utility.
3.
CMOS RTC and FDD Test
Insert the diskette to the floppy disk drive for test.
48
Chapter 2
.
4.
Thermal Test
5.
Config Test
6.
1394 ID Check
.
.
If you need to confirm whether the 1394GUID serial number has been input or not, you can run this utility.
Press^then Y key to next test.
Chapter 2
49
7.
Touchpad Test
After you run the utility, please point and move your finger on the touchpad. Then see if the movement of the
cursor can reach to left top (X=0, Y=0). Press the right and left button then continue next test.
8.
VGA R.G.B. Mode Test
Inspects red, green and blue color of display quality. Press any key to continue next test.
50
Chapter 2
9.
FAN Test
Check if the fan has turned on or not. You can confirm the function by a feather.
10. Keyboard Test
Press all keys according to this order--from left to right and from up to down to test each key’s function. If pass
then press b + Break to continue the next test.
11. 32bit Systemcard Test
Insert two pieces of Syscard (Card bus) into PCMCIA slots for test.
Chapter 2
51
12. Audio Test
Test the left channel first. After you hear a sound presseto test the right channel.
13. Battery Charge Test
Plug in AC adapter to the system for test.
52
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Small Philips screw driver
T
Philips screw driver
T
Flat head screwdriver
T
Large flat head screw driver
T
Tweezers
Nut driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
T
Chapter 3
53
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3. Remove the battery pack.
NOTE: TravelMate 530 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.
54
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
Mx2
Mx1
Heatsink
cover
Mx1
Middle Cover
Ox2
Memory
HDD Module
Ox2
Nx2
Fan
Nx1
Keyboard
Mx2
Optical
Module
Rx2
Sx2
FDD
Module
Px4
Dx2
Heatsink
HDD
Shielding
Mx2
Nx2
Ox2
CPU
LCD
Module
Optical
Brackets
Kx2
Mini PCI
EMI
Shielding
Optical
Drive
HDD
Carrier
Kx2
Hx4
Switch
Board
HDD
Connector
FDD
Bracket
Ox6 Jx2 Mx4
Nx2 Ix2 Kx2
Nx2
HDD
Optical
Drive Door
FDD Drive
LCD Bezel
Logic
Lower
Kx1
Logic
Upper
FDD FPC
LCD
Inverter
Kx2
Bx4
Touchpad
Bracket
Mx4
Dx4
Wireless
Card Power
Cable
Main
Board
LCD
Panel
FDD Door
Lx7
Lx1
Audio
Board
LCD w/
Brackets
Lx2
Speakers
Lx4
Touchpad
Cover
Wireless Card
Antenna Line
Touchpad
Hinge
Saddles
Lx4
Fx3
LCD Latch
Mx2
Ax2
LCD
Hinges
Fx4
Cx6
LCD
Brackets
LCD
Wireset
PCMCIA
Slot
Kx3
Optical
Drive
Brackets
Lx2
Phone
Jack
Board
Screw List
Item
Description
A
CPU FRAME NUT
B
Screw, #4-40UNF
C
Screw, M2.0X2.5NL
D
Screw, M2.0X3
E
Screw, M2.0X3NL
F
Screw, M2.0X5
G
Screw, M2.0X7
H
Screw, M2.0X0.4P+3FP-ZK(NL)
I
Screw, M2.5X12
J
Screw, M2.5X18
Chapter 3
55
Item
56
Description
K
Screw, M2.5X3NL
L
Screw, M2.5X4
M
Screw, M2.5X5
N
Screw, M2.5X7NL
O
Screw, M2.5X9NL
P
Screw, M3.0X3
Q
Screw, TPB-1.7 3.5P-ZK(NL)
R
Thermal screw with spring
S
Thermal screw with white spring
Chapter 3
Removing the Battery Pack
1.
Press the battery lock and slide the battery latch.
2.
Then remove the battery.
Chapter 3
57
Removing the HDD Module/Memory/FDD Module/Optical Module and
the CPU
Removing the HDD Module
1.
Remove the two screws that secure the HDD module.
2.
Then take the HDD module away.
Removing the Memory
1.
Remove the screw as shown here.
2.
Remove the DIMM door.
3.
Removing the Optical Module
58
1.
Remove the screw that secures the optical module.
2.
Push the optical module outwards.
3.
Then take out the optical module.
Chapter 3
Removing the FDD Module
1.
Remove the two screws that secures the FDD module.
2.
Disconnect FDD FPC.
3.
Then remove the FDD module.
Removing the CPU
1.
Replace the screw that secure the heatsink cover.
2.
Remove the heatsink cover.
3.
Remove the two screws that fasten the fan.
4.
Disconnect the fan cable then remove the fan..
5.
Remove the four screws as the picture shows.
6.
Then remove the heatsink..
7.
Unlock the CPU lock with the flat head screwdriver.
8.
Then remove the CPU
Chapter 3
59
60
Chapter 3
Removing the Keyboard, the Memory, the Modem Card, the LCD Module
and the Switch Board
Removing the Keyboard
1.
Remove the two screws on the bottom panel.
2.
Use a tool to pull the keyboard locks outwards as shown here.
3.
Disconnect the keyboard FPC, then detach the keyboard off the main unit.
Removing the Memory, the Modem Card (Bluetooth Card) and the Wireless LAN Card
1.
Pop up the memory then remove the memory.
2.
Unscrew the two screws that fasten the MDC door then remove the MDC door.
3.
Disconnect the modem card connector and modem card cable, then remove the modem card.
4.
Disconnect the LCD power cable.
5.
Remove the two screws holding the mini PCI EMI shielding.
6.
For bluetooth sku, you need to disconnect the bluetooth line, cable and the connector then remove the
bluetooth card.
7.
Then, disconnect the right antenna line.
8.
Pop up the wireless LAN card with fingures the remove the wireless LAN card.
Chapter 3
61
Removing the Switch Board and the LCD module
62
1.
Unscrew the two screws that secure the middle cover, one on each side.
2.
Use a tool to prize out the middle cover.
3.
Remove the two screws holding the switch board.
4.
Unscrew the two screws that fasten the LCD hinge, one on each side.
5.
Remove the two screws as shown here, one on each side.
6.
Take the two screws off the bottom panel as shown here, one on each side.
7.
Disconnect the LCD power cable.
8.
Then detach the LCD module off the main unit.
Chapter 3
Disassembling the Main Unit
Separate the main unit into the logic upper and the logic lower assembly
1.
Disconnect the audio board FFC.
2.
To detach logic upper assembly, first remove the five screws as shown here.
3.
Remove the two screws as shown here.
4.
Remove the eight screws holding the lower case.
5.
Detach the logic upper assembly form the logic lower assembly..
Disassembling the logic lower assemby
1.
To detach the main board off the lower case, first unscrew one screw holding the CPU support bracket.
2.
Then remove another screw as shown here.
3.
Remove the four hex head cap screws holding the main board.
4.
Unscrew the two screws as shown here.
5.
Detach the main board off the lower case.
6.
Disconnect the modem cable then remove the cable off the main board.
Chapter 3
63
Disassembling the Logic Upper Assembly
7.
Remove the two screws that fasten the left antenna, then remove another two screws on the other side
holding the right antenna line.
8.
Unscrew the six screws that secure the touchpad bracket then remove the touchpad bracket.
9.
Tear off the mylar that fasten the touchpad FFC then disconnect the FFC.
10. Disconnect the right and the left speaker cable.
11. Remove the two screws that secure the two speakers, one on each side.
12. Disconnect the audio board FFC.
13. Remove the screw that holds the audio-touchpad board then take the audio-touchpad board (with FFC)
off the lower case.
14. Disconnect the audio FFC from the audio-touchpad board.
15. Disconnect the phone jack FFC.
16. Disconnect the touchpad FFC off the audio-touchpad board.
64
Chapter 3
17. Remove the two screws that hold the hinge saddle.
18. Unscrew the two screws that fasten the other hinge saddle.
19. Remove the two screws holding the phone jack board assembly.
20. Then detach the phone jack cover off the phone jack board.
21. Take the EMI shielding off the lower case.
22. Release the touchpad cover locks as shown here.
23. Remove the touchpad cover then take the touchpad off the lower case.
Chapter 3
65
Disassembling the LCD Module
1.
Remove the two screwpad then unscrew the two screws on the LCD bezel. One on each side.
2.
Disattach the LCD bezel from the upper side of the LCD module carefully..
3.
Unscrew the screw that holds the LCD inverter.
4.
Disconnect the LCD wire set and LCD power cable from the LCD inverter.
5.
Remove the eight screws that secure the LCD to LCD panel; four on each side.
6.
Remove the LCD from the LCD panel.
7.
Remove the six screws holding the right and the left LCD brackets. Four on each side.
8.
Tear off the mylar that fastens the LCD wire set..
9.
Disconnect the LCD wire set.
10. Unscrew the two screws that secure the right and left hinges. Then remove the two hinges.
11. Unscrew the three screws then remove the LCD latch.
66
Chapter 3
Disassembling the External Modules
Disassembling the HDD Module
1.
Remove the four (two on each side) screws on HDD carrier.
2.
Remove the HDD EMI shielding and take out the HDD from the carrier.
3.
Disconnect the hard disk drive connector.
Disassembling the Floppy Disk Drive Module
1.
Remove the four screws (two on each side) that secure the FDD to the FDD bracket. Then remove the
FDD from the FDD bracket.
2.
Disconnect FDD FFC.
3.
Use a tool (a tip of a pen or an uncurved paper clipper) to release the FDD door lock on one side, then the
other. And you can remove the FDD door.
Disassembling the Optical Drive Module
1.
Unscrew the two screws holding the optical bracket.
2.
Then remove the optical bracket.
Chapter 3
67
68
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model (TravelMate 530 series). Non-Acer products,
prototype cards, or modified options can give false errors and invalid system responses.
1.
Obtain the failed symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You
can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
4.
After you perform visual inspection you can also verify the following:
ask the user if a password is registered and, if it is, ask him or her to enter the password.
verify with the customer that Wndows XP is installed on the hard disk. Operating systems that
were not preinstalled by Acer can cause malfunction.
make sure all optional equipment is removed from the computer.
make sure the floppy disk is empty.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 71.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 75
“Undetermined Problems” on page 82
POST detects an error and displayed messages
on screen.
“Error Message List” on page 76
The diagnostic test detected an error and
displayed a FRU code.
“System Diagnostic Diskette” on page 46
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 75
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 75
“Intermittent Problems” on page 81
“Undetermined Problems” on page 82
Chapter 4
69
System Check Procedures
External Diskette Drive Check
Do the following steps to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic
diskette is required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device. See “System Diagnostic Diskette” on page 46 for details.
1.
The FDD heads can become dirty over time, affecting their performance. Use an FDD cleaning kit to clean
the heads. If the FDD still does not function properly after cleaning, go to next step.
2.
Boot from diagnostic program (see“System Diagnostic Diskette” on page 46)
3.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the main board.
If the error still remains:
1.
Reconnect the external diskette drive module.
2.
Replace the external diskette drive module.
3.
Replace the main board.
External CD-ROM/DVD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM/DVD-ROM. Make sure that the CDROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to
fail.
Do the following to select the test device:
1.
Insert an audio CD into the CD/DVD drive. If the CD/DVD drive can read the data from the audio CD. The
drive does not have problem, then go to next step. If the CD/DVD LED on the front panel does not emit
light as it read the data from the audio CD, then go to next step. However, if the CD/DVD drive can not
read data from the audio CD, you may need to clean the CD/DVD drive with a CD/DVD drive cleaning
disk.
2.
Make sure that the appropriate driver has been installed on the computer for the CD/DVD drive.
3.
Boot from the diagnostics diskette and start the diagnostics program (refer to “System Diagnostic
Diskette” on page 46.)
4.
See if CD-ROM Test is passed when the program runs to CD-ROM/DVD-ROM Test.
5.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the main board. If the error still remains:
70
1.
Reconnect the CD-ROM/DVD-ROM module.
2.
Replace the CD-ROM/DVD-ROM module.
3.
Replace the main board.
Chapter 4
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the main board.
If the keyboard cable connection is correct, run the Keyboard Test. See “System Diagnostic Diskette” on page
46 for more details.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Embedded Numeric Keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory Check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
Currently, we do not provide memory test program. However, if you need to check memory but have no testing
program or diagonositc utility at hand, please go to http://www.passmark.com to download the shareware
“BurnIn Test V.3.0”. You may test the memory with this program under Window XP environment.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
Chapter 4
T
“Check the Power Adapter” on page 72
T
“Check the Battery Pack” on page 73
71
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: 19V
Pin 2: 0V, Ground
1.
If the voltage is not correct, replace the power adapter.
2.
If the voltage is within the range, do the following:
T
Replace the main board.
T
If the problem is not corrected, see “Undetermined Problems” on page 82.
T
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
72
3.
If the DC-IN indicator does not light up, check the power cord of the power adapter for correct continuity
and installation.
4.
If the operational charge does not work, see “Check the Power Adapter” on page 72.
Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Options in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
4.
If the voltage is within the normal range, run the diagnostic program.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not emit, replace the battery pack. If the charge indicator still does not light up,
replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
After rebooting, run Touch pad/PS2 Mode Driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the PS/2 mouse does not work, then check if the main board to switch board FPC is connected well.
4.
If the main board to switch board FPC is connected well, then check if the touch pad FPC connects to the
main board properly.
5.
If there is still an error after you have connected the touch pad FPC to the main board properly, then
replace the touch pad or touch pad FPC. The touch pad or touch pad FPC may be damaged.
6.
Replace switch board.
7.
If the touch pad still does not work, then replace the FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Display Check
1.
Connect an external display to the computer’s external monitor port, the boot the computer. The computer
can automatically detect the external display. Press Fn+ p to switch to the external display.
2.
If the external display works fine, the internal LCD may be damaged. Then perform the following steps:
Make sure the DDRRAM module is seated properly. Then run the diplay test again. If the problem
still exists, go to next step.
Replace the inverter board, then run the display test program again. If the problem still occurs, go
on next step.
Replace the LCD module with a new one then run the display test again. If the probelm still
happens, continue next step.
Replace LCD/FL cable with a new one then execute the display diagnostic again. If the problem
Chapter 4
73
still occurs, continue next step.
Replace the CPU with another of the same specifications. If the problems still occurs, go to next
step.
The main board may be damaged. Replace main board.
3.
If the external monitor has the same problem as the internal monitor, the main board may be damaged.
Please insert the diagnostic disk and run the display test program and go through the sub-steps under
step 2.
Sound Check
To determine if the computer’s built-in speakers are functioning properly, perform the following steps. Before
you start the steps below, adjust the speaker volume to an appropriate level.
74
1.
Try different audio sources. For example, employ audio CD and ditital music file to determine whether the
fault is in the speaker system or not. If not all sources have sound problem, the problem is in the source
devices. If all have the same problem, continue next step.
2.
Connect a set of earphone or external speakers. If these devices work fine, go to next step. If not, then the
main board may be defective or damaged. Replace the main board.
3.
Follow the disassembling steps in Chapter 3. Esure the speaker cable is firmly connected to the main
board. If the speaker is still a malfunction, go on next step.
4.
If the speakers do not sound properly, the speakers may be defective or damaged. Replace the speakers.
If the problem still occurs, then replace the main board.
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 82.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
75
Index of Error Messages
Error Message List
Error Messages
0200 Failure Fixed Disk
FRU/Action in Sequence
Hard disk error detected.
Check to see if fixed disk is attached properly.
Enter the BIOS Setup Utility and verify the hard disk is detected.
0211 Keyboard error
see “Keyboard or Auxiliary Input Device Check” on page 71.
0212 Keyboard Controller Failed
see “Keyboard or Auxiliary Input Device Check” on page 71.
May require replacing the keyboard controller.
0213Keyboard locked - Unlock key switch
Unlock the system to proceed.
0220 Monitor type does not match CMOS - Run
SETUP
Display device mismatch.
0230 System RAM Failed at offset: nnnn
Enter the BIOS Setup Utility and verify the parameters (try loading
the default settings); then save and restart the computer.
Shadow RAM test failed
Main board
0231 Shadow RAM Failed at offset: nnnn
System RAM test failed
Main board
0232 Extended RAM Failed at address line: nnnn Extended RAM test failed
Main board
0250 System battery is dead - Replace and run
SETUP
CMOS clock battery needs to be replaced. Replace the battery and
run BIOS Setup Utility to reconfigure system time, then reboot
system.
0251 System CMOS checksum bad - Default
configuration used
CMOS has been corrupted or modified incorrectly.
Run BIOS Setup Utility and verify the parameters; then save and
restart the computer.
Check the system battery.
0260 System timer error
System timer test fiailed, and the main board needs to be repaired.
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Main board
0270 Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Main board
0280 Previous boot incomplete - Default
configuration used
Previous boot-up was not copleted successfully.
Enter the BIOS Setup Utility and verify the parameters (try loading
the default settings); then save and restart the computer.
RTC battery
Main board
0281 Memory size found by POST differed from
EISA CMOS
Run “Load Setup Defaults” in BIOS Setup Utility.
02B0 Diskette drive A error
Drive A: or B: is present but fails the BIOS POST diskette tests.
Main board
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
Check if the diskette drive is attached correctly.
See “External Diskette Drive Check” on page 70.
02B2 Incorrect Drive A type - run SETUP
Type of floppy drive A: not correctly identified in Setup.
Main board
02D0 System cache error - Cache disabled
RAM cache failed and BIOS disabled the cache.
On older boards, check the cache jummpers. You may have to
replace the cache.
Main board
76
Chapter 4
Error Message List
Error Messages
02F0 CPU ID
FRU/Action in Sequence
CPU socket number for Multi-Processor error.
Main board
02F4 EISA CMOS not writeable
System unable to write to EISA CMOS.
Main board
02F5 DMA Test Failed
System unable to write to DMA (Direct Memory Access) registers.
Main board
02F6 Software NMI Failed
System unable to generate software NMI (Non-Maskable Interrupt).
Main board
02F7 Fail-Safe Timer NMI Failed
Fail-Safe Timer takes too long.
Invalid System Configuration Data
Error with NVRAM (CMOS) data.
Main board
Enter the BIOS Setup Utility and verify the parameters (try loading
the default settings); then save and restart your computer.
Main board
Operating system not found
Operating system cannot be found on the boot device.
Enter the BIOS Setup Utility and verify the parameters (try loading
the default settings); then save and restart the computer.
Recover hard disk.
Reinstall the operating system.
Parity Check 1 nnnn
Parity error found on system bus. BIOS attempts to locate the
address and display it on the screen. If it cannot locate the address,
it displays.
Parity Check 2 nnnn
Parity error found on I/O bus. BIOS attempts to locate the address
and display it on the screen. If it cannot locate the address, it
displays .
Chapter 4
77
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
LCD is too dark
Enter BIOS Utility to execute “Load Setup Defaults” on Exit screen,
then reboot system.
LCD brightness cannot be adjusted
Reconnect the LCD connectors.
LCD contrast cannot be adjusted
Keyboard (if contrast and brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Unreadable LCD screen
Reconnect the LCD connector
Missing pels in characters
LCD cable
Abnormal screen
LCD inverter
Wrong color displayed
LCD
Main board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter
LCD cable
LCD
Main board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
Main board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 71.
Battery pack
Power adapter
Hard drive & battery connection board
Main board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 71“.
Battery pack
Power adapter
Hard drive & battery connection board
Main board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” on page 71.
Hold and press the power switch for more than 4 seconds.
Main board
Battery can’t be charged
See “Check the Power Adapter” on page 72.
Battery pack
Main board
78
Chapter 4
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
See “System Diagnostic Diskette” on page 46. Please run Sycard 32
Bit test.
PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.
Action in Sequence
See “Sound Check” on page 74
Audio driver
Speaker
Main board
Internal speakers make noise or emit no sound.
See “Sound Check” on page 74
Speaker
Main board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation
Action in Sequence
Keyboard (if control is from the keyboard)
Hard disk drive
Main board
The system doesn't enter hibernation mode and
four short beeps every minute.
Press Fn+F4 and see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
Main board
The system doesn’t enter standby mode after
closing the LCD
LCD cover switch
The system doesn't resume from hibernation
mode.
Hard disk connection board
Main board
Hard disk drive
Main board
The system doesn't resume from standby mode
after opening the LCD.
LCD cover switch
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Remove battery pack and let it cool for 2 hours.
Main board
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
Main board
System hangs intermittently.
Reconnect hard disk drives.
Hard disk drive connector
Main board
Chapter 4
79
Peripheral-Related Symptoms
Symptom / Error
System configuration does not match the
installed devices.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Setup defaults”, then
reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly.
See “System Diagnostic Diskette” on page 46
See if there is an error beep. If there is an erro beep, then change
main board.
Power off. Then check if RAM CPU BIOS are well-connected.
Press Fn+F5 three times slowly
LCD FPC
LCD inverter
LCD
USB does not work correctly
USB device cable is firmly connected into the USB ports. Test one
USB port each time.
USB socket is firmly secured to the main board.
Main board
Print problems.
Ensure the “Parallel Port” in the “System Devices” of BIOS Setup
Utility is set to Enabled.
Onboard Devices Configuration
Run parallel port test
Printer driver
Printer cable
Printer
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
Main board
Touchpad does not work.
Reconnect touch pad cable. Modem port is secured to the main
board
Touch pad FPC
Audio/Touch pad board
Main board
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Ensure the telephone cable is firmly plugged into the telephone wall
socket and the modem port of the computer.
Modem phone port is secured to the main board.
modem combo board
Main board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 82.
80
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the diagnostic test for several times to isolate the problem.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
If an error is detected by the main battery test, see “Check the Power Adapter” on page 72
If an error is detected by the display test, see “Index of Symptom-to-FRU Error Message” on page
78 .
If an error is detected by the floppy disk drive test, see “External Diskette Drive Check” on page 70.
If an error is detected by the keyboard test, see “Keyboard or Auxiliary Input Device Check” on
page 71.
Chapter 4
81
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 71):
82
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
CD-ROM/Diskette drive Module
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
Main board
T
LCD assembly
Chapter 4
Index of AFlash BIOS Error Message
Error Message
Action in Sequence
Hardware Error
See “System Diagnostic Diskette” on page 46
VPD Checksum Error
Reboot the system and then restest with this diskette.
BIOS Update Program Error
Turn off the power and restart the system.
System Error
Make sure this AFlash BIOS diskette for this model.
Without AC adapter
make sure to connect AC adapter
Battery Low
make sure to install a highly charged battery, and reboot
system.
Chapter 4
83
84
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
1
USB Connector Port
12
DC Jack Port
2
USB Connector Port
13
Modem Connector
3
USB Connector Port
14
IEEE 1394 Connector
4
TV-Out Connector
15
RJ11 Connector
5
Panel Connector
16
Battery Connector
6
RJ45 Connector Port
17
MDC Connector
7
Panel Backlight On/Off Switch
18
DDR 200Pin Port
8
LPTCN-27 Port
20
Internal Keyboard Connector
9
Switch Buttom Interface Connector
22
Audio Board to Main Board Connector
10
SPR Connector
23
Mini PCI Connector
11
CRT Connector Port
24
System On/Off Button
Chapter 5
85
SW3 Settings
SW3
PANEL BACKLIGTH ON/OFF BUTTON
Setting
ON: PANLE BACKLIGHT ON
OFF: PANEL BACKLIGHT OFF
SW2 Settings
SW2
POWER BUTTON
Setting
ON:SYSTEM ON
OFF: SYSTEM OFF
86
Chapter 5
Bottom View
1
HDD Connector
2
Card Reader Connector
6
CPU FAN Connector
3
FDD Connector
7
CPU Socket
4
DDR 200Pin So-Dimm Connector
8
CD-ROM Port
Chapter 5
5
PCMCIA Connector 84Pin Port
87
88
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 530
series products. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise
Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
89
Exploded Diagram
THE SYSTEM
90
Chapter 6
LOGIC UPPER ASSY
TravelMate 270
Chapter 6
91
LCD 14.1”
TravelMate270
92
Chapter 6
LCD 15”
TravelMate 270
Chapter 6
93
DVD ASSY
TravelMate 270
NOTE: The exploded diagrams for CD-ROM, DVD-ROM and DVD-RW combo module are very similar.
Therefor, we put only DVD ASSY exploded diagram for your reference. Please also refer to the FRU list
below for more information on different models and part numbers. This diagram only explains the
relevant location of each part. The parts on the exploded diagrams may be a slightly different from its
actual looks.
94
Chapter 6
FDD ASSY
TravelMate 270
HDD (W/O HDD) ASSY
TravelMate 270
Chapter 6
95
Picture
No.
Partname And Description
Part Number
Adapter
NS
ADAPTER-DELTA 75W (3 pin)
AP.T2303.001
ADAPTER-ASTEC 70W (3 pin)
AP.80304.002
BATTERY LI-ION 8 CELLS 2150MAH
PANASONIC CGR18650C
BT.18605.001
BATTERY LI-ION 8 CELLS 2150MAH
SAMSUNG ICR18650-22
BT.18606.001
251-Logic
Upper
AUDIO/TOUCHPAD BOARD
55.T24V5.001
252-The
system
SWITCH BOARD
55.T24V5.002
252-Logic
Upper
PHONE JACK BOARD
55.T18V5.003
NS
MODEM BOARD AMBIT U98M005.05MDC
SCOPI01
54.T24V5.001
NS
MODEM / BLUETOOTH COMBO BOARD
AMBIT T60M665.00
54.T24V5.002
NS
WIRELESS LAN BOARD (802.11b) AMBIT T60H
656.02 PRISM
54.T24V5.003
NS
WIRELESS LAN BOARD (802.11a+b) AMBIT
T60H677.01
54.T24V5.004
Battery
NS
Boards
Cables
96
Chapter 6
Picture
No.
Partname And Description
Part Number
016-Logic
Upper
AUDIO FFC CABLE 38 PIN
50.T24V5.001
003-Logic
Upper
TOUCHPAD FFC CABLE
50.T18V5.002
004-Logic
Upper
PHONE JACK FFC CABLE
50.T18V5.003
NS
MODEM CABLE
50.T24V5.002
NS
POWER CORD US (3Pin)
27.T18V5.001
POWER CORD EC (3Pin)
27.T18V5.002
POWER CORD Aus (3Pin)
27.T18V5.003
POWER CORD UK (3Pin)
27.T18V5.004
POWER CORD SWISS (3Pin)
27.T18V5.005
POWER CORD CHINA (3Pin)
27.T18V5.006
POWER CORD ITALLIAN (3Pin)
27.T18V5.007
POWER CORD DEMARK (3Pin)
27.T18V5.008
002-Logic
Upper
ANTENNA LINE-L
50.T18V5.005
001-Logic
Upper
ANTENNA LINE-R
50.T18V5.006
NS
MODEM CABLE
50.T24V5.004
Communication Module
Case/Cover/Bracket Assembly
Chapter 6
97
Picture
NS
98
No.
Partname And Description
Part Number
312-The
System
MIDDLE COVER W/NAME PLATE
42.T24V5.001
322-The
System
MIDDLE COVER SCREW PAD
47.T18V5.003
314-The
System
DIMM COVER
42.T18V5.002
313-The
System
HEATSINK COVER
42.T18V5.003
311-The
System
LOWER CASE
60.T24V5.002
253-The
System
UPPER CASE W/O SPEAKER
60.T24V5.003
101-Logic
Upper
EMI BRACKET W/ MYLARS, THERMAL PAD
60.T24V5.004
310-The
System
MINI PCI EMI SHIELDING
31.T18V5.001
Chapter 6
Picture
Chapter 6
No.
Partname And Description
Part Number
003-DVD
ASSY
OPTICAL DRIVE BRACKET
33.T24V5.001
104-Logic
Upper
TOUCHPAD BRACKET
33.T18V5.002
NS
TOUCHPAD COVER
42.T18V5.004
NS
CPU SUPPORT BRACKET
33.T18V5.003
102-Logic
Upper
HINGE SADDLE-R
34.T18V5.001
103-Logic
Upper
HINGE SADDLE-L
34.T18V5.002
105-Logic
Upper
PHONE JACK COVER
42.T18V5.005
BATTERY LATCH/KNOB KIT W/ SPRING &
LATCH COVER
6K.T18V5.001
MODEM DOOR
42.T24V5.002
99
Picture
No.
Partname And Description
Part Number
CPU
NS
INTEL PENTIUM 4-M (NORTHWOOD) 1.8GHZ/
512K/400FSB/1.3V/478PIN/ C-1 STEPPING
01.P4MNW.1G8
INTEL PENTIUM 4-M (NORTHWOOD) 1.9GHZ/
512K/400FSB/1.3V/478PIN/ C-1 STEPPING
01.P4MNW.1G9
INTEL PENTIUM 4-M (NORTHWOOD) 2.0GHZ/
512K/400FSB/1.3V/478PIN/ C-1 STEPPING
01.P4MNW.2G0
INTEL PENTIUM 4-M (NORTHWOOD) 2.2GHZ/
512K/400FSB/1.3V/478PIN/ C-1 STEPPING
01.NORTH.22B
INTEL PENTIUM 4-M (NORTHWOOD) 2.2GHZ/
512K/400FSB/1.3V/478PIN/ C-1 STEPPING
01.P4MNW.2G4
FDD MODULE PANASONIC JU-226A273FC
REV. 2
6M.T18V5.010
FDD MODULE, MITSUMI (D353G-4513)
6M.T24V5.003
FDD/Floppy Disk Drive
FDD ASSY
011-FDD
ASSY
FDD DRIVE PANASONIC JU-226A273FC REV.2 KF.22602.001
002-FDD
ASSY
FDD BEZEL FOR PANASONIC
42.T18V5.016
FDD BEZEL FOR MITSUMI
42.T18V5.017
001-FDD
ASSY
FDD BRACKET FOR PANASONIC
33.T18V5.004
FDD BRACKET FOR MITSUMI
33.T18V5.005
FDD FPC CABLE FOR PANASONIC
50.T18V5.007
FDD FPC CABLE FOR MITSUMI
50.T18V5.008
010-FDD
ASSY
100
FDD DRIVE MITSUMI (D353G-4513)
KF.35306.001
Chapter 6
Picture
No.
Partname And Description
Part Number
HDD/ Hard Disk Drive
NS
HDD 20GB/2.5 IN./4200RPM/HGST CASCADE
IC25N020ATCS04-0 07N8325
KH.02007.001
HDD 30GB/2.5 IN./4200RPM/HGST CASCADE
IC25N030ATCS04-0 07N8326
KH.03007.001
HDD 40GB/2.5 IN./4200RPM/HGST CASCADE
IC25N040ATCS04-0 07N8327
KH.04007.001
HDD 20GB/2.5 IN./4200RPM/TOSHIBA TITAN
MK2018GAP
KH.25204.001
HDD 30GB/2.5 IN./ 4200RPM/TOSHIBA TITAN
MK3018GAP
KH.25304.001
HDD 40GB/2.5 IN./4200RPM/TOSHIBA TITAN
MK4018GAP
KH.25404.001
HDD 20GB/2.5 IN./4200RPM/HITACHI
EUCALYPTUS DK23EA
KH.32005.002
HDD 30GB/2.5 IN./4200RPM/HITACHI
EUCALYPTUS DK23EA/30
KH.33005.002
HDD 40GB/2.5 IN./4200RPM/Hitachi Eucalyptus
DK23EA/-40
KH.34005.002
003-HDD
(W/O HDD)
ASSY
HDD CARRIER
42.T18V5.018
010-HDD
(W/O HDD)
ASSY
HDD CONNECTOR
22.T18V5.002
002-HDD
(W/O HDD)
ASSY
HDD BRACKET COVER
33.T18V5.016
NS
KEYBOARD DARFON ARABIC NSK-A650A
84KEYS
KB.T1802.010
KEYBOARD DARFON BELGIUM NSK-A651A
85KEYS
KB.T1802.012
KEYBOARD DARFON CHINESE NSK-A6502
84KEYS
KB.T1802.005
KEYBOARD DARFON CZECH NSK-A650C
85KEYS
KB.T1802.014
KEYBOARD DARFON DANISH NSK-A650D
85KEYS
KB.T1802.017
KEYBOARD DARFON FRENCH NSK-A650F
85KEYS
KB.T1802.006
Keyboard
Chapter 6
101
Picture
No.
Partname And Description
Part Number
KEYBOARD DARFON GERMAN NSK-A650G
85KEYS
KB.T1802.003
KEYBOARD DARFON HUNGAIAN NSK-A650Q
85KEYS
KB.T1802.015
KEYBOARD DARFON ITALIAN NSK-A650E
85KEYS
KB.T1802.004
KEYBOARD DARFON NORWAY NSK-A650N
85KEYS
KB.T1802.016
KEYBOARD DARFON PORTUGUESE NSKA6506 85KEYS
KB.T1802.009
KEYBOARD DARFON SPANISH NSK-A650S
85KEYS
KB.T1802.008
KEYBOARD DARFON SWEDEN NSK-A650W
85KEYS
KB.T1802.013
KEYBOARD DARFON SWISS/G NSK-A6500
85KEYS
KB.T1802.007
KEYBOARD DARFON THAI NSK-A6503
84KEYS
KB.T1802.011
KEYBOARD DARFON TURKISH NSK-A650T
85KEYS
KB.T1802.018
KEYBOARD DARFON UK NSK-A650U
85KEYS
KB.T1802.002
KEYBOARD DARFON US INTERNATIONAL
NSK-A651D 84KEYS
KB.T1802.001
LCD MODULE 14.1" TFT XGA AU UB141XN04
V.2 5AXXX
6M.T24V5.011
LCD MODULE 14.1" TFT XGA CPT
CLAA141XF01 REV.2
6M.T24V5.012
LCD MODULE 15" TFT XGA AU B150XG01
V0.2
6M.T24V5.013
LCD MODULE 15" TFT XGA LG LP150X05
6M.T24V5.014
LCD MODULE 15" TFT XGA HITACHI
TX38D85VC1CAB REV.A
6M.T24V5.015
LCD 14.1" TFT XGA AU UB141XN04 V.2
5AXXX
LK.14105.002
LCD MODULE 14.1" TFT XGA CPT
CLAA141XF01 REV.2
LK.14109.002
LCD
LCD 14.1”
and LCD 15”
001-LCD
14.1” and
LCD 15”
003-LCD
14.1” and
LCD 15”
102
LCD 15" TFT XGA AU B150XG01 V0.2
LK.15005.001
LCD 15" TFT XGA LG LP150X05
LK.15008.003
LCD 15" TFT XGA HITACHI TX38D85VC1CAB
REV.A
LK.15004.003
LCD INVERTER T51I056.01
19.T24V5.001
Chapter 6
Picture
No.
104-LCD
14.1” and
LCD 15
Partname And Description
Part Number
LCD BRACKET 14.1" LEFT
33.T18V5.006
LCD BRACKET 15" LEFT W/HINGE FOR AU
XGA
6K.T24V5.002
LCD BRACKET 15" LEFT W/HINGE FOR LG
XGA
6K.T24V5.004
LCD BRACKET 15" LEFT W/HINGE FOR
HITACHI XGA
6K.T24V5.006
LCD BRACKET 14.1" RIGHT
33.T18V5.007
LCD BRACKET 15" LEFT W/HINGE FOR AU
XGA
6K.T24V5.001
LCD BRACKET 15" LEFT W/HINGE FOR LG
XGA
6K.T24V5.003
LCD BRACKET 15" LEFT W/HINGE FOR
HITACHI XGA
6K.T24V5.005
102-LCD
14.1” and
LCD 15”
LCD PANEL WITH LOGO-14”
60.T18V5.004
LCD PANEL WITH LOGO-15”
60.T24V5.005
NS
LCD KNOB LATCH KIT W/ SPRING
6K.T18V5.002
101-LCD
14.1” and
LCD 15”
LCD BEZEL 14.1”
60.T18V5.005
LCD BEZEL WITH RUBBER-15.0”
60.T18V5.007
002-LCD
14.1” and
LCD 15”
LCD COAXIAL CABLE 14.1" FOR AU
50.T18V5.009
NS
LCD COAXIAL CABLE 14.1" FOR CPT
50.T18V5.010
LCD COAXIAL CABLE 15" FOR AU XGA
50.T18V5.011
LCD COAXIAL CABLE 15" FOR LG XGA
50.T18V5.012
103-LCD
14.1” and
LCD 15”
LCD COAXIAL CABLE 15" FOR HITACHI XGA
50.T18V5.013
108-14.1”
LCD
LCD RUBBER for 14.1” LCD
47.T18V5.001
107-14.1”
LCD
LCD SCREW PAD
47.T18V5.002
Main Board
Chapter 6
103
Picture
No.
Partname And Description
Part Number
251-The
System
MAINBOARD W/O CPU, MEMORY, MODEM
CABLE
MB.T2402.001
NS
PCMCIA SLOT
21.T18V5.001
NS
MEMORY SO-DIMM DDR266/128MB/ NANYA
NT128D64S88A2GM-7K
KN.12803.002
MEMORY SO-DIMM DDR266/128MB/
INFIENON HYS64D16020GDL-7-A
KN.12802.002
MEMORY SO-DIMM DDR266/128MB APACER
UNB CL2.5
77.10921.580
MEMORY SO-DIMM DDR266/256MB/0.175U
NANYA/NT256D64S88AMGM-7K
KN.25603.006
MEMORY SO-DIMM DDR266/256MB/0.14U /
INFINEON HYS64D32020 GDL-7-B
KN.25602.001
MEMORY SO-DIMM DDR266/256MB/
MITSUBISHI MH32D64AKS-75G-JE
KN.25608.001
MEMORY SO-DIMM DDR266/256MB/ MICRON
MT8VDDT3264HDG-265B1
KN.25604.002
MEMORY SO-DIMM DDR266/256MB/ APACER
UNB CL2.5
77.11021.580
MEMORY SO-DIMM DDR266/512MB/
MITSUBISHI MH64D64AKQH-75
KN.51208.001
DVD-ROM MODULE 8X TOSHIBA SD-C2612
6M.T18V5.005
DVD-ROM MODULE 8X MKE SR-8177
6M.T24V5.001
Memory
Optical Drive
DVD ASSY
101-DVD
ASSY
104
DVD-ROM MODULE 8X LITEON LSD-081
6M.T18V5.007
DVD-RW COMBO MODULE 24X KME
UJDA740
6M.T18V5.102
DVD-RW COMBO MODULE 24X QSI SBW-241
6M.T18V5.104
DVD-RW COMBO MODULE 24X TEAC DW224E
6M.T24V5.002
DVD-ROM MODULE 8X TOSHIBA SD-C2612
KV.08X01.001
DVD-ROM MODULE 8X MKE SR-8177
KV.08X02.001
DVD-ROM MODULE 8X LITEON LSD-081
KV.08X04.001
DVD-RW COMBO MODULE 24X KME
UJDA740
KO.24X03.001
DVD-RW COMBO MODULE 24X QSI SBW-241
KO.24X07.001
DVD-RW COMBO MODULE 24X TEAC DW224E
KO.24X02.001
Chapter 6
Picture
No.
NS
NS
Partname And Description
Part Number
DVD-ROM BEZEL FOR TOSHIBA
42.T18V5.010
DVD-ROM BEZEL FOR MKE
42.T24V5.003
DVD-ROM BEZEL FOR LITEON
42.T18V5.013
DVD-RW COMBO BEZEL FOR KME
42.T18V5.015
DVD-RW COMBO BEZEL FOR QSI
42.T18V5.019
DVD-RW COMBO BEZEL FOR TEAC
42.T24V5.004
OPTICAL LOCK
22.T18V5.001
5-IN-1 MEMORY CARD READER
6M.T24V5.021
Others
Chapter 6
5-IN-1 MEMORY CARD READER BOARD
55.T24V5.003
MEMORY CARD READER FPC CABLE
50.T24V5.003
CARD READER CASE LOWER
42.T24V5.005
CARD READER CASE UPPER
42.T24V5.006
CARD READER BRACKET
33.T24V5.002
007-Logic
Upper
SPEAKER-R
23.T18V5.002
008-Logic
Upper
SPEAKER-L
23.T18V5.003
107-Logic
Upper
TOUCHPAD SYNAPTICS TM41P357
56.T18V5.001
NS
FAN
31.T18V5.002
105
Picture
No.
Partname And Description
Part Number
315-The
System
CPU HEATSINK
23.T18V5.001
NS
MIDDLE COVER NAME PLATE
40.T18V5.001
Screws
106
CPU FRAME NUT
86.T18V5.001
SCREW, #4-40UNF
86.T18V5.002
SCREW, M2.0*2.5 NL
86.T18V5.003
SCREW, M2.0*3
86.T18V5.004
SCREW, M2.0*3 NL
86.T18V5.005
SCREW, M2.0*5
86.T18V5.006
SCREW, M2.0*7
86.T18V5.007
SCREW, M2.5*12
86.T18V5.009
SCREW, M2.5*18
86.T18V5.010
SCREW, M2.5*3 N
86.T18V5.011
SCREW, M2.5*4
86.T18V5.012
SCREW, M2.5*5
86.T18V5.013
SCREW, M2.5*7 NL
86.T18V5.014
SCREW, M2.5*9 NL
86.T18V5.015
SCREW, M3.0*3
86.T18V5.016
SCREW, TPB-1.7 3.5P-ZK(NL)
86.T18V5.017
SCREW, M2.0*3 (FDD)
86.T18V5.020
SCREW, M1.7*2.5
86.T18V5.021
THERMAL SCREW WITH SPRING
86.T18V5.018
THERMAL SCREW WITH WHITE SPRING
86.T18V5.019
Chapter 6
Chapter 6
107
Appendix A
Model Definition and Configuration
TravelMate 530 Series
Model
Number
CPU
LCD
TM531XV
Pentium 4
1.8Ghz
14.1 XGA
1x256M
30G
8x DVD
TM531XC
Pentium 4
1.8Ghz
14.1 XGA
1x256M
30G
24x CDRW
+DVD
TM533XV
Pentium 4
2.0Ghz
14.1 XGA
1x256M
30G
8x DVD
TM533XVi
Pentium 4
2.0Ghz
14.1 XGA
1x256M
30G
8x DVD
TM533XC
Pentium 4
2.0Ghz
14.1 XGA
1x256M
30G
24x CDRW
+DVD
TM533XCi
Pentium 4
2.0Ghz
14.1 XGA
1x256M
30G
24x CDRW
+DVD
TM533LV
Pentium 4
2.0Ghz
15.0 XGA
1x256M
40G
8x DVD
TM533LC
Pentium 4
2.0Ghz
15.0 XGA
2x256M
30G
24x CDRW
+DVD
TM533LCi
Pentium 4
2.0Ghz
15.0 XGA
2x256M
30G
24x CDRW
+DVD
TM535LC
Pentium 4
2.4Ghz
15.0 XGA
2x256M
40G
24x CDRW
+DVD
TM535LCi
Pentium 4
2.4Ghz
15.0 XGA
2x256M
40G
24x CDRW
+DVD
Model
Number
FDD
TM531XV
N
TM531XC
TM533XV
Card Reader
Memory
HDD (GB)
Wireless LAN
(Mini PCI)
ODD
Bluetooth
(MDC)
Bluetooth
(int. USB)
5 in 1
N
N
N
N
5 in 1
N
N
N
int. FDD
N
N
N
N
TM533XVi
int. FDD
N
802.11b
N
N
TM533XC
int. FDD
N
N
N
N
Note: GC area
does not have
int. FDD.
Note: GC area
has 5 in 1 card
reader,
TM533XCi
int. FDD
N
802.11b
N
N
TM533LV
N
5 in 1
N
N
N
TM533LC
int. FDD
N
N
N
N
TM533LCi
int. FDD
N
802.11b
N
N
TM535LC
int. FDD
N
N
N
N
TM535LCi
int. FDD
N
802.11b
N
N
Appendix A
108
Main Features
109
T
Mobile Intel® Pentium®4 processor-M at 1.8GHz or higher
T
Built-in 0.13 micron technology; includes 512KB L2 cache; supports Enhanced Intel®
SpeedStepTM technology; 400MHz processor system bus
T
Standard 256MB DDR-266 SDRAM, upgradeable up to 1GB on dual SoDIMM sockets
T
Integrated 24x CD-ROM/8x DVD-ROM or 24/10/8/24x DVD/CD-RW combo drive
T
20/30/40GB or higher-capacity Ultra DMA-100HDD
T
High-capacity, Enhanced-IDE hard disk
T
Li-Ion main battery pack
T
Power management system with ACPI (Advanced Configuration Power Interface) 2.0 supporting
Standby and Hibernation power saving modes
T
Thin-Film Transistor (TFT) liquid-crystal display (LCD) displaying 32-bit high true colour up to
1024X768 eXtended Graphics Array (XGA) resolution for 14.1”/15.0” (specification varies
depending on models)
T
3D capabilities
T
Shared Memory Architechure (Intel DVMT-Dynamic Video Memory Technology)
T
Simultaneous display on LCD and CRT
T
Support S-video(NTSC/PAL) TV-out
T
“Automatic LCD dim” feature that automatically decides the best settings for your display and
conserves pwer
T
Dual display capability
T
16-bit high-fidelity AC’97 stereo audio
T
Built-in dual speakers
T
Built-in microphone
T
High-speed optical drive
T
High-speed fax/data modem port
T
Ethernet/Fast Ethernet port
T
USB (Universal Serial Bus) ports
T
IEEE 1394 port
T
Optional Invilink 802.11b wireless LAN
T
Optional Integrated Bluetooth module
T
5 Launch keys, including Internet Browser and email and 3 user-programmable keys
T
4-way scroll button
T
Sleek, smooth and stylish design
T
Full-sized keyboard
T
Ergonomically-centered touchpad pointing device
T
Two type II or one type III cardBus PC Card slots
T
Upgradeable memory
Appendix A
Appendix A
110
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home, Windows® XP Professional and Windows® 2000
environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the TravelMate 530 series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
111
Microsoft® Windows® XP Home Environment Test
Category
PCMCIA
PS2
USB
112
Vendor
Type
Device
Xircom
Xircom 32bit CardBus Ethernet 10/100
LAN
BUFFALD
Card Bus 10/100M LPCS-CLX-CB
LAN
Adaptec
Adaptec SlimSCSI 16 bit (APA-1460A)
SCSI
DATAFAB
PCMCIA to Memory Stick
Memory Stick
Zonet
FAX Modem PC Card 56Kbps
Modem
DATAFAB
PCMCIA to Compact Flash
Compact Flash
USB 2.0 Hi-Speed CardBus Adapter
USB 2.0
fotocom
my 1394 CardBus Adapter
IEEE 1394
NOKIA
NOKIA Card Phone 2.0 (m/n:RPM-1)
Card Phone2.0
SMC
Wireless PC Card m/n: SMC2632W V.2
Wireless LAN
Lucent
Lucent Technologies m/n:PC-24E-FC
Wireless LAN
Logitech
M-S35
Mouse
Microsoft
Wheel Mouse Serial and PS/2
Compatible (m/n:WM1)
Mouse
Microsoft
Natural Keyboard Pro (m/n:RT9431
V:5FTWTA)
Keyboard
Compaq
Korean 166516-AD6
Keyboard
Acer
6311-HW
keyboard
CREATIVE
Web CAM (m/n:PD1030)
Camera
3Com
PC Digital Camera
Camera
Logitech
Quick Cam for Macintosh OS9 (m/n:VUT16)
Camera
DIAMOND
56K Modem
Modem
BEST DATA
56K V.90 Modem
Modem
A-mego
USB to Card Reader
Card Reader
PENPOWER
Hand Writer (T-20275U)
Hand Writer
Microsoft
Trackball Optical 1.0 PS2/USB
Compatible
Mouse
HP
f2100a
Mouse
Macally
LoptJr.
Mouse
Microsoft
Side Winder Plug&Play Game Pad
Game Pad
Microsoft
Natual Keyboard Pro (m/n: RT9431
V:5FTWTA)
Keyboard
Chicony
m/n: KU-8933
Keyboard
PCI
Bluetooth m/n:GW-BH02U
Bluetooth
3Com
USB Network ethernet adapter
LAN
billionton
10/100 FastEthernet (P/N:USBKR2100B)
LAN
Galileo
Slim HDD combo (1394+USB 2.0)
HDD
Vi Power
Smart HANDY Disk (USB 2.0)
HDD
Logitech
WingMan RUMBLEPAD (m/n:G-UA3)
Rumble Pad
Sony
MPF82E
FDD
Mitsumi
D353FUE
FDD
Appendix B
Category
LAN
Vendor
Type
Device
Y-E Data
YD-8u10
FDD
HP
DeskJet 640C (LPT+USB)
Printer
HP
ScanJet 5200C
Scanner
Philips
USB Digital Speaker System DSS350/
17T
Speaker
Genius
Wireless Optical/Receiver (USB+PS/2)
Wireless Mouse
Logitech
Cordless Optical Mouse (m/n:M-RM67A) Wireless Mouse
BELKIN
4 Port HUB (m/n:F5U001) USB 2.0
HUB
TEAC
4 Port HUB (m/n:US-4S-20S) USB 2.0
HUB
D-Link
10/100 Fast Ethernet Switch DES1008D
HUB
HP
Procurve Switch 2424M
HUB
Accton
ES3508/tx
HUB
PCI
FX-08EA
HUB
Acer
SP0008
HUB
3Com
3C16735B
HUB
Buffalo
LSW10/100-8N
HUB
EPSON
LQ-2080c
Printer
HP
HP LaserJet 5000 Series PCL 6
Printer
HP
DeskJet 640C (LPT+USB)
Printer
SCSI
SONY
CD-ROM m/n:CDU415
CD-ROM
IEEE 1394
unknow
unknow
HDD
Galileo
Slim HDD combo (1394+USB)
HDD
RICOH
DVD+RW MP5120A
DVD+RW
NEC
Multisync LCD 1530
Monitor
View Sonic
Graphics Series GS790
Monitor
Toshiba
17” LCD
Monitor
Video
S-Video
SHARP
29J-S200T
TV
Mic.
Labtec
unknow
Mic.
Headphone
KOKA
CD-1200
Headphone
Philips
USB Digital Speaker System DSS350/
17T
D-Link
D-Link DWL-1000AP
D-Link
Ethernet Link Activity/100M
802.11b
Lucent
m/n:WP-II E
802.11b
SMC
SMC7004VWBR
802.11b
LPT
CRT
Access Pont
Appendix B
802.11b
113
Category
Memory Card
114
Vendor
Panasonic
Type
VW-MMCB 8MB MultiMediaCard
Device
MMC
JVC
CU-MMC08U 8MB MultiMediaCard
MMC
Panasonic
32MB SD card
SD
Apacer
128MB SmartMedia card
SmartMedia
Apacer
128MB CompactFlash card
Compact Flash
Apacer
128MB Memory Stick card
Memory Stick
Blue Tooth
PCI
Blue tooth m/n:GW-BH02U
USB
Modem Port
Panasonic
Advanced Hybrid System KX-TA308
MODEM
Appendix B
Microsoft® Windows® XP Pro Environment Test
Category
PCMCIA
PS2
USB
Appendix B
Vendor
Type
Device
Xircom
Xircom 32bit CardBus Ethernet 10/100
LAN
BUFFALD
Card Bus 10/100M LPCS-CLX-CB
LAN
Adaptec
Adaptec SlimSCSI 16 bit (APA-1460A)
SCSI
DATAFAB
PCMCIA to Memory Stick
Memory Stick
Zonet
FAX Modem PC Card 56Kbps
Modem
DATAFAB
PCMCIA to Compact Flash
Compact Flash
USB 2.0 Hi-Speed CardBus Adapter
USB 2.0
fotocom
my 1394 CardBus Adapter
IEEE 1394
NOKIA
NOKIA Card Phone 2.0 (m/n:RPM-1)
Card Phone2.0
SMC
Wireless PC Card m/n: SMC2632W
V.2
Wireless LAN
Lucent
Lucent Technologies m/n:PC-24E-FC
Wireless LAN
Logitech
M-S35
Mouse
Microsoft
Wheel Mouse Serial and PS/2
Compatible (m/n:WM1)
Mouse
Microsoft
Natural Keyboard Pro (m/n:RT9431
V:5FTWTA)
Keyboard
Compaq
Korean 166516-AD6
Keyboard
Acer
6311-HW
keyboard
CREATIVE
Web CAM (m/n:PD1030)
Camera
3Com
PC Digital Camera
Camera
Logitech
Quick Cam for Macintosh OS9 (m/n:VUT16)
Camera
DIAMOND
56K Modem
Modem
BEST DATA
56K V.90 Modem
Modem
A-mego
USB to Card Reader
Card Reader
PENPOWER
Hand Writer (T-20275U)
Hand Writer
Microsoft
Trackball Optical 1.0 PS2/USB
Compatible
Mouse
HP
f2100a
Mouse
Macally
LoptJr.
Mouse
Microsoft
Side Winder Plug&Play Game Pad
Game Pad
Microsoft
Natual Keyboard Pro (m/n: RT9431
V:5FTWTA)
Keyboard
Chicony
m/n: KU-8933
Keyboard
PCI
Bluetooth m/n:GW-BH02U
Bluetooth
3Com
USB Network ethernet adapter
LAN
billionton
10/100 FastEthernet (P/N:USBKR2100B)
LAN
Galileo
Slim HDD combo (1394+USB 2.0)
HDD
Vi Power
Smart HANDY Disk (USB 2.0)
HDD
Logitech
WingMan RUMBLEPAD (m/n:G-UA3)
Rumble Pad
Sony
MPF82E
FDD
Mitsumi
D353FUE
FDD
115
Category
Type
Device
Y-E Data
YD-8u10
FDD
HP
DeskJet 640C (LPT+USB)
Printer
HP
ScanJet 5200C
Scanner
Philips
USB Digital Speaker System DSS350/
17T
Speaker
Genius
Wireless Optical/Receiver (USB+PS/
2)
Wireless Mouse
Logitech
Cordless Optical Mouse (m/n:MRM67A)
Wireless Mouse
BELKIN
4 Port HUB (m/n:F5U001) USB 2.0
HUB
TEAC
4 Port HUB (m/n:US-4S-20S) USB 2.0
HUB
D-Link
10/100 Fast Ethernet Switch DES1008D
HUB
HP
Procurve Switch 2424M
HUB
Accton
ES3508/tx
HUB
PCI
FX-08EA
HUB
Acer
SP0008
HUB
3Com
3C16735B
HUB
Buffalo
LSW10/100-8N
HUB
EPSON
LQ-2080c
Printer
HP
HP LaserJet 5000 Series PCL 6
Printer
HP
DeskJet 640C (LPT+USB)
Printer
SCSI
SONY
CD-ROM m/n:CDU415
CD-ROM
IEEE 1394
unknow
unknow
HDD
Galileo
Slim HDD combo (1394+USB)
HDD
RICOH
DVD+RW MP5120A
DVD+RW
NEC
Multisync LCD 1530
Monitor
View Sonic
Graphics Series GS790
Monitor
Toshiba
17” LCD
Monitor
Video
S-Video
SHARP
29J-S200T
TV
Mic.
Labtec
unknow
Mic.
Headphone
KOKA
CD-1200
Headphone
Philips
USB Digital Speaker System DSS350/
17T
LAN
LPT
CRT
116
Vendor
Appendix B
Category
Access Pont
Memory Card
Vendor
Type
Device
D-Link
D-Link DWL-1000AP
802.11b
D-Link
Ethernet Link Activity/100M
802.11b
Lucent
m/n:WP-II E
802.11b
SMC
SMC7004VWBR
802.11b
Panasonic
VW-MMCB 8MB MultiMediaCard
MMC
JVC
CU-MMC08U 8MB MultiMediaCard
MMC
Panasonic
32MB SD card
SD
Apacer
128MB SmartMedia card
SmartMedia
Apacer
128MB CompactFlash card
Compact Flash
Apacer
128MB Memory Stick card
Memory Stick
Blue Tooth
PCI
Blue tooth m/n:GW-BH02U
USB
Modem Port
Panasonic
Advanced Hybrid System KX-TA308
MODEM
Appendix B
117
Microsoft® Windows® 2000 Environment Test
Category
PCMCIA
PS2
USB
118
Vendor
Type
Device
Xircom
Xircom 32bit CardBus Ethernet 10/100
LAN
BUFFALD
Card Bus 10/100M LPCS-CLX-CB
LAN
Adaptec
Adaptec SlimSCSI 16 bit (APA-1460A)
SCSI
DATAFAB
PCMCIA to Memory Stick
Memory Stick
Zonet
FAX Modem PC Card 56Kbps
Modem
DATAFAB
PCMCIA to Compact Flash
Compact Flash
USB 2.0 Hi-Speed CardBus Adapter
USB 2.0
fotocom
my 1394 CardBus Adapter
IEEE 1394
NOKIA
NOKIA Card Phone 2.0 (m/n:RPM-1)
Card Phone2.0
SMC
Wireless PC Card m/n: SMC2632W
V.2
Wireless LAN
Lucent
Lucent Technologies m/n:PC-24E-FC
Wireless LAN
Logitech
M-S35
Mouse
Microsoft
Wheel Mouse Serial and PS/2
Compatible (m/n:WM1)
Mouse
Microsoft
Natural Keyboard Pro (m/n:RT9431
V:5FTWTA)
Keyboard
Compaq
Korean 166516-AD6
Keyboard
Acer
6311-HW
keyboard
CREATIVE
Web CAM (m/n:PD1030)
Camera
3Com
PC Digital Camera
Camera
Logitech
Quick Cam for Macintosh OS9 (m/n:VUT16)
Camera
DIAMOND
56K Modem
Modem
BEST DATA
56K V.90 Modem
Modem
A-mego
USB to Card Reader
Card Reader
PENPOWER
Hand Writer (T-20275U)
Hand Writer
Microsoft
Trackball Optical 1.0 PS2/USB
Compatible
Mouse
HP
f2100a
Mouse
Macally
LoptJr.
Mouse
Microsoft
Side Winder Plug&Play Game Pad
Game Pad
Microsoft
Natual Keyboard Pro (m/n: RT9431
V:5FTWTA)
Keyboard
Chicony
m/n: KU-8933
Keyboard
PCI
Bluetooth m/n:GW-BH02U
Bluetooth
3Com
USB Network ethernet adapter
LAN
billionton
10/100 FastEthernet (P/N:USBKR2100B)
LAN
Galileo
Slim HDD combo (1394+USB 2.0)
HDD
Vi Power
Smart HANDY Disk (USB 2.0)
HDD
Logitech
WingMan RUMBLEPAD (m/n:G-UA3)
Rumble Pad
Sony
MPF82E
FDD
Mitsumi
D353FUE
FDD
Appendix B
Category
Vendor
Type
Device
Y-E Data
YD-8u10
FDD
HP
DeskJet 640C (LPT+USB)
Printer
HP
ScanJet 5200C
Scanner
Philips
USB Digital Speaker System DSS350/
17T
Speaker
Genius
Wireless Optical/Receiver (USB+PS/
2)
Wireless Mouse
Logitech
Cordless Optical Mouse (m/n:MRM67A)
Wireless Mouse
BELKIN
4 Port HUB (m/n:F5U001) USB 2.0
HUB
TEAC
4 Port HUB (m/n:US-4S-20S) USB 2.0
HUB
D-Link
10/100 Fast Ethernet Switch DES1008D
HUB
HP
Procurve Switch 2424M
HUB
Accton
ES3508/tx
HUB
PCI
FX-08EA
HUB
Acer
SP0008
HUB
3Com
3C16735B
HUB
Buffalo
LSW10/100-8N
HUB
EPSON
LQ-2080c
Printer
HP
HP LaserJet 5000 Series PCL 6
Printer
HP
DeskJet 640C (LPT+USB)
Printer
SCSI
SONY
CD-ROM m/n:CDU415
CD-ROM
IEEE 1394
unknow
unknow
HDD
Galileo
Slim HDD combo (1394+USB)
HDD
RICOH
DVD+RW MP5120A
DVD+RW
NEC
Multisync LCD 1530
Monitor
View Sonic
Graphics Series GS790
Monitor
Toshiba
17” LCD
Monitor
Video
S-Video
SHARP
29J-S200T
TV
Mic.
Labtec
unknow
Mic.
Headphone
KOKA
CD-1200
Headphone
Philips
USB Digital Speaker System DSS350/
17T
LAN
LPT
CRT
Appendix B
119
Category
Access Pont
Memory Card
120
Vendor
Type
Device
D-Link
D-Link DWL-1000AP
802.11b
D-Link
Ethernet Link Activity/100M
802.11b
Lucent
m/n:WP-II E
802.11b
SMC
SMC7004VWBR
802.11b
Panasonic
VW-MMCB 8MB MultiMediaCard
MMC
JVC
CU-MMC08U 8MB MultiMediaCard
MMC
Panasonic
32MB SD card
SD
Apacer
128MB SmartMedia card
SmartMedia
Apacer
128MB CompactFlash card
Compact Flash
Apacer
128MB Memory Stick card
Memory Stick
Blue Tooth
PCI
Blue tooth m/n:GW-BH02U
USB
Modem Port
Panasonic
Advanced Hybrid System KX-TA308
MODEM
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides for all models
T
User's manuals
T
Training materials
T
Bios updates
T
Software utilities
T
Spare parts lists
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveler's Warranty (ITW)
T
Returned material authorization procedures
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
121
122
Appendix C
Index
A
D
AC Adapter 31
DIMM 23
ACPI 1.0a 23
Combinations 24
external 58
package 23
removing 58
Speed 23
voltage 23
AFLASH Utility 46
Audio 26, 27
B
Disassembly
Battery 28
Battery Pack 55
CD-ROM/DVD-ROM Module 63
Floppy Disk Drive 66
Machine 53
Procedure Flowchart 55
Battery Pack 57
battery pack
charging indicator 12
BIOS 23
package 23
password control 23
ROM size 23
ROM type 23
vendor 23
Version 23
Display 3
DVD-ROM Interface 25
E
Error Symptom-to-Spare Part Index 75
BIOS Setup Utility 35
BIOS Supports protocol 23
BIOS Utility 35
External CD-ROM Drive Check 70
F
Basic System Settings 40
Navigating 36
Onboard Device Configuration 42
Startup Configuration 41
System Information 36
System Security 45
Features 1
features 109
Flash Utility 46
Floppy Disk
removing the 66
Board Layout 4
Floppy Disk Drive Interface 24
Bottom View 5
Top View 4
FRU (Field Replaceable Unit) List 89
H
C
Hard disk 25, 27
Cache
HDD 25, 27
controller 23
size 23
caps lock
Hot Keys 13
I
on indicator 12
Indicators 12
CardBus 27
Intermittent Problems 81
computer
on indicator 12
J
Core logic 27
Jumper and Connector Locations 85
CPU
core voltage 23
package 23
type 23
Index
Top View 85
K
123
Keyboard 27
System Check Procedures 70
Keyboard or Auxiliary Input Device Check 71
System Diagnostic Diskette 46
System Memory 23
L
System Specifications
L2 cache 23
Features 109
LAN/Modem Combo 24
System Utilities 35
System Utility Diskette 46
M
Machine Disassembly 53
T
Temperature 32
media access
Test Compatible Components 111
on indicator 12
Memory Check 71
Touchpad Check 73
Model Definition 108
Troubleshooting 69
Modem 24
Modem Combo Card
U
Undetermined Problems 82
external 61
USB 27
N
utility
num lock
on indicator 12
BIOS 35
V
O
Video 26
Online Support Information 121
Resolutions 26
Video controller 27
P
Panel 6
Bottom 11
left 6
Rear 9
right 9
W
Windows 2000 Environment Test 112
Parallel Port 26
PC Card 12, 27
PCMCIA 27
Pentium III 23
Power System Check
Battery Pack 73
Power Adapter 72, 73
Processor 23
R
RMA 89
RTC 27
S
Second Level Cache 23
Super I/O 27
System
Block Diagram 3
Layout 4
124
Index