Technical information | Acer 5530G Laptop User Manual

Aspire 5530/5530G Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire 5530/5530G Series service guide.
Date
II
Chapter
Updates
Copyright
Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed as is. Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's global product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Touchpad Basics (with fingerprint reader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Special Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Acer GridVista (dual-display compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
System Utilities
27
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
AMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
WinFlash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Removing HDD Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Removing BIOS Passwords: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Machine Disassembly and Replacement
47
Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Removing the SD dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the ExpressCard dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Removing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Removing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Removing the TV tuner Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
VII
Table of Contents
Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Removing the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Removing the Finger Print Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Removing the Upper Right Saddle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Removing the Left Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Removing the Upper Left Saddle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Removing the Touch Pad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Removing the Launch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the Media Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the eKey Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Removing the Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Removing the Right Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Removing the TV Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Removing the Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Removing the USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Removing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Removing the Subwoofer Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Removing the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Removing the RJ-11 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Removing the VGA Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Removing the Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Removing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Removing the LCD Brackets and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . .106
Removing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Removing the MIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Replacing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Replacing the VGA Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Replacing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Replacing the RJ-11 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Replacing Subwoofer Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Replacing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Replacing the Bluetooth Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Replacing the TV Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Replacing the Right Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Replacing the Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Replacing the eKey Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Replacing the Media Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Replacing the Upper Right Saddle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
VIII
Table of Contents
Replacing the Launch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Replacing the Finger Print Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Replacing the Touch Pad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Replacing the Left Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Replacing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Replacing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Replacing the Antenna Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Replacing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Replacing the TV Tuner Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
Replacing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Replacing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
Replacing the Express and SD Card Trays . . . . . . . . . . . . . . . . . . . . . . . . . . .141
Troubleshooting
143
Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
Touchpad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Internal Microphone Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
USB Failure (Rightside) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Modem Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
EasyTouch Button Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
MediaTouch Button Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Fingerprint Reader Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
HDTV Switch Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
POST Codes Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
Chipset POST Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
Jumper and Connector Locations
165
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
FRU (Field Replaceable Unit) List
171
Aspire 5530 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
Discrete SKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
UMA SKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
IX
Table of Contents
Aspire 5530 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174
Model Definition and Configuration
184
Aspire 5530 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
Test Compatible Components
187
Microsoft® Windows® Vista Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
With Fingerprint Reader SKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
Without Fingerprint Reader SKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
Online Support Information
193
Index
195
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
NOTE: Items marked with * denote only selected models.
Operating System
•
Windows® Vista™
Platform
•
AMD Better By Design program, featuring:
•
AMD Turion™ Dual-Core Processor*
•
AMD Athlon™ Dual-Core Processor*
•
AMD M780G Chipset
•
Acer InviLink™ 802.11b/g*
•
Acer InviLink™ Nplify™ 802.11b/g/Draft-N*
System Memory
•
Dual-Channel DDR2 support
•
Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules
Display and graphics
•
15.4" WXGA 1280 x 800
•
ATI Mobility Radeon™ HD 3200/3470/3650 Graphics (for Aspire 5530G only)
TV Tuner
•
Digital TV-tuner supporting DVB-T*
Storage subsystem
•
2.5" hard disk drive
•
Optical drive options:
•
•
Blu-ray Disc™ /DVD-Super Multi double-layerdrive
•
DVD-Super Multi double-layer drive
5-in-1 card reader
Dimensions and Weight
Chapter 1
•
364.6 (W) x 272.3 (D) x 30.8/43.7 (H) mm (14.3 x 10.6 x 1.2/1.7 inches)
•
3.0 kg (6.61 Ibs)
1
Audio
•
Dolby® certified surround sound system with two built-in stereo speakers and one subwoofer
supporting low-frequency effects
•
S/PDIF (Sony/Philips Digital Interface) support for digital speakers
•
True5.1-channel surround sound output
•
High-definition audio support
•
MS-Sound compatible
•
Built-in microphone
Communication
•
•
Acer Video Conference, featuring:
•
Integrated Acer Crystal Eye webcam
•
Optional Acer Xpress VoIP phone
WLAN:
•
Acer InviLink™ 802.11b/g*
•
Acer InviLink™ Nplify™ 802.11b/g/Draft-N*
•
WPAN: Bluetooth® 2.0+EDR
•
LAN: Gigabit Ethernet, Wake-on-LAN ready
•
Modem: 56K ITU V.92
Privacy control
•
Acer Bio-Protection fingerprint solution
•
BIOS user, supervisor, HDD passwords
•
Kensington lock slot
Power subsystem
•
ACPI 3.0
•
71 W 4800 mAh
•
48.8 W 4400 mAh
•
3-pin 65/90 W AC adapter*
•
Energy Star 4.0
Special keys and controls
2
•
88-/89-/93-key keyboard
•
Touchpad pointing device
•
Empowering Key
•
Easy-launch buttons: WLAN, Internet, email, Bluetooth, Acer Arcade™
•
Acer MediaTouch keys: play/pause, stop, previous, next
•
Volume wheel
•
Acer Media Center remote control*
Chapter 1
I/O interface
•
ExpressCard™/54 slot
•
5-in-1 card reader (SD™, MMC, MS, MS PRO, xD)
•
Four USB 2.0 ports
•
HDMI™ port with HDCP support
•
Consumer infrared (CIR) port
•
External display (VGA) port
•
RF-in jack*
•
Headphone/speaker/line-out jack with S/PDIF support
•
Microphone-in jack
•
Line-in jack
•
Ethernet (RJ-45) port
•
Modem (RJ-11) port
•
DC-in jack for AC adapter
•
Acer EasyPort IV connector
Environment
•
•
Temperature:
•
Operating: 5 °C to 35 °C
•
Non-operating: -20 °C to 65 °C
Humidity (non-condensing):
•
Operating: 20% to 80%
•
Non-operating: 20% to 80%
NOTE: Items marked with * denote only selected models.
Chapter 1
3
System Block Diagram
4
Chapter 1
Your Acer Notebook tour
After knowing your computer features, let us show you around your new computer.
Front View
No.
Icon
Item
Description
1
Microphone
2
Acer Crystal Eye
Web camera for video communication.
3
Display screen
Also called Liquid-Crystal Display (LCD),
displays computer output.
4
Power button
Turns the computer on and off.
5
Speakers
Left and right speakers deliver stereo audio
output.
6
Easy-launch
buttons
Buttons for launching frequently used program.
7
Keyboard
For entering data into your computer.
8
Palmrest
Comfortable support area for your hands when
you use the computer.
9
Touchpad
Touch-sensitive pointing device which functions
like a computer mouse.
Chapter 1
Internal microphone for sound recording.
5
No.
Icon
Item
Description
10
Click buttons
(left, center* and
right)
The left and right buttons function like the left
and right mouse buttons. *The center button
serves as Acer Bio-Protection fingerprint
reader supporting Acer FingerNav 4-way
control function (only for certain models).
11
Status indicators
Light-Emitting Diodes (LEDs) that light up to
show the status of the computer's functions
and components.
12
Acer MediaTouch
keys
For use with Acer Arcade and other media
playing programs.
13
Empowering key
Launch Acer Empowering Technology.
14
Status indicators
Light-Emitting Diodes (LEDs) that light up to
show the status of the computer's functions
and components.
Closed Front View
No.
6
Icon
Item
Description
1
5-in-1 card
reader
Accepts Secure Digital (SD), MultiMediaCard
(MMC), Memory Stick (MS), Memory Stick
PRO (MS PRO), xD-Picture Card (xD).
2
CIR receiver
Receives signals from a remote control.
3
Latch
Locks and releases the lid
Chapter 1
Left View
No.
Icon
Item
Description
1
Kensington lock
slot
Connects to a Kensington-compatible
computer security lock.
2
Acer EasyPort IV
connector
Connects to Acer EasyPort IV.
3
Ethernet (RJ-45)
port
Connects to an Ethernet 10/100/1000-based
network.
4
External display
(VGA) port
Connects to a display device
(e.g. external monitor, LCD projector).
HDMI
Connects to a television or display device with
HDMI input.
6
2 USB 2.0 ports
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
7
Line-in jack
Accepts audio line-in devices (e.g. audio CD
player, stereo walkman).
8
Microphone-in
jack
Accepts input from external microphones.
9
Headphones/
speaker/line-out
jack with S/PDIF
support
Connects to audio line-out devices
(e.g. speakers, headphones).
10
Unlimited volume
control wheel
Adjust the volume of the audio-out.
11
ExpressCard/54
slot
Accepts one ExpressCard/54 module.
5
Chapter 1
HDMI
7
Right View
No.
Icon
Item
Description
1
USB 2.0 port
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
2
Optical drive
Internal optical drive; accepts CDs or DVDs.
3
Optical disk access
indicator
Lights up when the optical drive is active.
4
Optical drive eject
button
Ejects the optical disk from the drive.
5
Emergency eject
hole
Ejects the optical drive tray when the computer is
turned off. Note: Insert a paper clip into the
emergency eject hole to eject the optical drive
tray when the computer is off.
6
USB 2.0 port
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
7
RF-in Port
Accepts input signals from digital TV tuner
devices (only for certain models).
8
Modem (RJ-11)
port
Connects to a phone line.
Rear View
No.
8
Icon
Item
Description
1
DC-in jack
Connects to an AC adapter
2
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
Chapter 1
Bottom View
No.
Icon
Item
Description
1
Battery bay
Houses the computer's battery pack.
2
Battery release
latch
Releases the battery for removal.
3
Battery lock
Locks the battery in position.
4
Memory
compartment
Houses the computer's main memory.
5
Sub-woofer
Emits low frequency sound output.
6
Hard disk bay
Houses the computer's hard disk (secured with
screws).
7
Ventilation slots
and cooling fan
Enable the computer to stay cool, even after
prolonged use.
Note: Do not cover or obstruct the opening of the
fan.
Chapter 1
9
Indicators
The computer has several easy-to-read status indicators:
The front panel indicators are visible even when the computer cover is closed.
Icon
Function
Description
Power
Indicates the computer's power status.
Battery
Indicates the computer's battery status.
HDD
Indicates when the hard disk drive is active.
Num Lock
Lights up when Num Lock is activated.
Caps Lock
Lights up when Caps Lock is activated.
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Easy-Launch Buttons
Located beside the keyboard are application buttons. These buttons are called easy-launch buttons. They are:
WLAN, Internet, email, Bluetooth, Arcade and Acer Empowering Technology.
The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To
set the Web browser, mail and programmable buttons, run the Acer Launch Manager.
Icon
10
Function
Description
Empowering Technology
Launch Acer Empowering Technology.
(user-programmable)
Acer Arcade
Launch Acer Arcade utility
Wireless communication
button/indicator
Enables/disables the wireless function. Indicates
the status of wireless LAN communication.
Web browser
Internet browser (user-Programmable)
Mail
Email application (user-Programmable)
Bluetooth communication
button/indicator
Enables/disables the Bluetooth function. Indicates
the status of Bluetooth communication.
Chapter 1
Touchpad Basics (with fingerprint reader)
The following items show you how to use the touchpad with Acer Bio-Protection fingerprint reader:
•
Move your finger across the touchpad (2) to move the cursor.
•
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad is the same as clicking the left button.
•
Use Acer Bio-Protection fingerprint reader (3) supporting Acer FingerNav 4-way control function
(only for certain models) or the 4-way scroll (3) button (only for certain models) to scroll up or down
and move left or right a page. This fingerprint reader or button mimics your cursor pressing on the
right scroll bar of Windows applications.
Function
Execute
Left Button (1)
Right Button (3)
Quickly click twice.
Main touchpad (2)
Tap twice (at the same speed
as double-clicking a mouse
button).
Select
Click once.
Tap once.
Drag
Click and hold, then use
finger on the touchpad to
drag the cursor.
Tap twice (at the same speed
as double-clicking a mouse
button); rest your finger on
the touchpad on the second
tap and drag the cursor.
Access
context menu
Click once.
NOTE: When using the touchpad, keep it - and your fingers - dry and clean. The touchpad is sensitive to finger
movement; hence, the lighter the touch, the better the response. Tapping too hard will not increase the
touchpad’s responsiveness.
Chapter 1
11
Using the Keyboard
The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function
and special keys.
Lock Keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed are in uppercase.
Num Lock
<Fn> + <F11>
When Num Lock is on, the embedded keypad is in numeric mode. The keys
function as a calculator (complete with the arithmetic operators +, -, *, and /). Use
this mode when you need to do a lot of numeric data entry. A better solution
would be to connect an external keypad.
Scroll Lock <Fn> +
<F12>
When Scroll Lock is on, the screen moves one line up or down when you press
the up or down arrow keys respectively. Scroll Lock does not work with some
applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
12
Num Lock on
Num Lock off
Number keys on
embedded keypad
Type numbers in a normal manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using cursorcontrol keys.
Hold <Fn> while using cursorcontrol keys.
Main keyboard keys
Hold <Fn> while typing letters on
embedded keypad.
Type the letters in a normal
manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Description
Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;
it launches the Start menu. It can also be used with other keys to provide a variety of
functions:
<
>:
Open or close the Start menu
<
>
+ <D>: Display the desktop
<
>
+ <E>: Open Windows Explore
<
>
+ <F>: Search for a file or folder
<
>
+ <G>: Cycle through Sidebar gadgets
<
>
+ <L>: Lock your computer (if you are connected to a network domain), or
switch users (if you're not connected to a network domain)
<
>
+ <M>: Minimizes all windows
<
>
+ <R>: Open the Run dialog box
<
>
+ <T>: Cycle through programs on the taskbar
<
>
+ <U>: Open Ease of Access Center
<
>
+ <X>: Open Windows Mobility Center
<
>
+ <BREAK>: Display the System Properties dialog box
<
>
+ <SHIFT+M>: Restore minimized windows to the desktop
<
>
+ <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D
<
>
+ <SPACEBAR>: Bring all gadgets to the front and select Windows Sidebar
<CTRL> + <
>
<CTRL> + <
>
+ <F>: Search for computers (if you are on a network)
+ <TAB>: Use the arrow keys to cycle through programs on the
taskbar by using Windows Flip 3-D
Note: Depending on your edition of Windows Vista, some shortcuts may not function
as described.
Application
key
Chapter 1
This key has the same effect as clicking the right mouse button; it opens the
application's context menu.
13
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hotkey
14
Icon
Function
Description
<Fn> + <F1>
Hotkey help
Displays help on hotkeys.
<Fn> + <F2>
Acer eSettings
Management
Launches Acer eSettings Management in Acer
Empowering Technology.
<Fn> + <F3>
Acer ePower
Management
Launches Acer ePower Management in Acer
Empowering Technology.
<Fn> + <F4>
Sleep
Puts the computer in Sleep mode.
<Fn> + <F5>
Display toggle
Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn> + <F6>
Screen blank
Turns the display screen backlight off to save
power. Press any key to return.
<Fn> + <F7>
Touchpad toggle
Turns the internal touchpad on and off.
<Fn> + <F8>
Speaker toggle
Turns the speakers on and off.
<Fn> + < >
Brightness up
Increases the screen brightness.
<Fn> + < >
Brightness down
Decreases the screen brightness.
<Fn> + <F1>
Hotkey help
Displays help on hotkeys.
<Fn> + <F2>
Acer eSettings
Management
Launches Acer eSettings Management in Acer
Empowering Technology.
Chapter 1
Special Key
You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your
keyboard.
The Euro symbol
1.
Open a text editor or word processor.
2. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard.
NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1.
Open a text editor or word processor.
2. Hold <Shift> and then press the <4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
Chapter 1
15
Using the System Utilities
Acer Bio-Protection (only for certain models) Acer Bio-Protection Fingerprint Solution is a multi-purpose
fingerprint software package integrated with the Microsoft Windows operating system. Utilizing the uniqueness
of one's fingerprint features, Acer Bio-Protection Fingerprint Solution has incorporated protection against
unauthorized access to your computer with centralized password management with Password Bank, easy
music player launching with Acer MusicLaunch, secure Internet favorites via Acer MyLaunch, and fast
application/website launching and login with Acer FingerLaunch, while Acer ProfileLaunch can launch up to
three applications/websites from a single finger swipe.
Acer Bio-Protection Fingerprint Solution also allows you to navigate through web browsers and documents
using Acer FingerNav. With Acer Bio-Protection Fingerprint Solution, you can now enjoy an extra layer of
protection for your personal computer, as well as the convenience of accessing your daily tasks with a simple
swipe of your finger!
For more information refer to the Acer Bio-Protection help files.
Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then
select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the
display box and then click the check box Extend my windows desktop onto this monitor. Finally, click
Apply to confirm the new settings and click OK to complete the process.
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start´ All Programs and click on Acer GridVista.
You may choose any one of the four display settings indicated below:
16
Chapter 1
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is simple to set up:
1.
2.
3.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
Drag and drop each window into the appropriate grid.
Enjoy the convenience of a well-organized desktop.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Chapter 1
17
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
Griffin - Turionx2 / Athlonx2 for MS/Griffin - Athlonx2 / Sempron for
Value
Core logic
NB/SB AMD M780M/SB700
CPU package
Sig2 uPGA638
CPU core voltage
1.2V~0.8V
CPU Fan True Value Table
DTS (degree C°)
Fan Speed (rpm)
Acoustic Level (dBA)
55
2800
31
65
3200
34
75
3600
37
90
4000
40
100
4000
40
•
CPU DTS Throttling 50% point = 100C; /recover 85C
BIOS
Item
Specification
BIOS vendor
Phoenix
BIOS Version
V0.19T1
BIOS ROM type
Flash
BIOS ROM size
2MB
BIOS package
ACPI 2.0 compliance with Intel Speed Step Support C1, C2, C3,
C4, C6 and S3, S4 for mobile CPU
Supported protocols
•
Support ISIPP
•
Support Acer UI
•
Support multi-boot
•
Suspend to RAM (S3)/Disk (S4)
•
Various hot-keys for system control
•
Support SMBUS 2.0, PCI2.3
•
Support PXE
•
Support Y2K solution
•
Support Win Flash Wake on LAN from S3
•
Wake on LAN form S4 in AC mode
•
System information
•
Support ASF 2.0
•
Support iTPM (GM / PM Sku)
Cache
Item
Specification
Cache controller
CPU
Cache size
1MB for Turionx2/Athlonx2, 512KB for Simpron
System Memory
Item
Memory controller
18
Specification
Built-in
Chapter 1
Item
Specification
Memory size
0MB (no on-board memory)
DIMM socket number
2 sockets
Supports memory size per socket
2 GB
Supports maximum memory size
4G for 64bit OS (with two 2GB SODIMM)
Supports DIMM type
DDR 2 Synchronous DRAM 667/800 MHz
Memory module combinations
You can install memory modules in any combinations as long as
they match the above specifications.
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
512MB
512MB
0MB
1024MB
1024MB
0MB
2048MB
2048MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
512MB
2048MB
2560MB
1024MB
0MB
1024MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
1024MB
2048MB
3072MB
2048MB
0MB
2048MB
2048MB
512MB
2560MB
2048MB
1024MB
3072MB
2048MB
2048MB
4096MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
LAN Interface
Item
Specification
LAN Chipset
Broadcom BCM5764MKMLG
Supports LAN protocol
IEEE 802.3, 802.3u, 802.3ab, 802.3p
LAN connector type
RJ-45
LAN connector location
RJ-45 (right-rear side on the system)
Features
Gigabit Ethernet
Bluetooth Interface
Item
Chipset
Specification
BCM2045
Data throughput
3Mbps
Protocol
IEEE 802.15
Interface
USB
Connector type
mini-USB
Chapter 1
19
Wireless Module 802.11b/g
Item
Specification
Chipset
BCM4312
Data throughput
54Mbps
Protocol
802.11b/g
Interface
pci-E
Hard Disk Drive Interface
Item
Specification
Vendor &
Model
Name
Segate
ST9250827AS
Segate
ST9160310AS
Toshiba
MK1246GSX
Toshiba
MK1652GSX
Hitachi
5K320-320
5K320-250
Capacity
(MB)
250
160
120
160
320, 250
Bytes per
sector
512
512
512
512
512
Data heads
4
2
2
2
4, 4 or 3
Disks
2
1
1
1
2, 2
Spindle
speed
(RPM)
5400
5400
5400
5400
5400
Drive Format
Performance Specifications
Buffer size
8 MB
8 MB
8 MB
8 MB
8 MB
Interface
SATA
SATA
SATA
SATA
SATA
Internal
transfer
rate (Mbits/
sec, max)
778
352
370 ~ 730
typical
400 ~ 794
typical
674 ~ 775
I/O data
transfer
rate
(Mbytes/
sec max)
300
150
300
300
1.5 / 3.0
5V ±5%
5V ±5%
5V ±5%
5V ±5%
DC Power Requirements
Voltage
tolerance
20
5V ±5%
Chapter 1
Super-Multi Combo Module
Item
Specification
Manufacturer and Model
Sony DL 8X AD-7560S
Toshiba DL 8X TS-L633A
Type
Drawer type
Interface
SATA
Data Transfer Modes
•
PIO Mode4
•
DMA Multiword Mode2
•
ULTRA DMA Mode2
Buffer Memory Size
2 MB
Maximum Write Speed
•
CD-R Max. 24X (3,600 KB/sec)
•
DVD+RW Max 8X (10,800 KB/sec)
•
CD 3,600 KB/sec
•
DVD 10,800 KB/sec
Maximum Read Speed
Format Compatibility
CD
•
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
•
CD-ROM (Yellow Book Mode1 & 2) - Standard Data
•
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
•
CD-I (Green Book, Mode2 Form1 & 2, Ready, Bridge)
•
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
•
Video-CD (White Book) - MPEG1 Video
•
CD-R (Orange Book Part ‡U)
•
CD-RW & HSRW (Orange Book Part IV Volume1 & Volume2)
•
Super Audio CD (SACD) Hybrid type
•
US & US+ RW
DVD
•
DVD-ROM (Book 1.02), DVD-Dual
•
DVD-Video (Book 1.1)
•
DVD-R (Book 1.0, 3.9G)
•
DVD-R (Book 2.0, 4.7G) - General & Authoring
•
DVD+R (Version 1.0)
•
DVD+RW
•
DVD-RW (Non CPRM & CPRM)
•
DVD±R Dual
•
DVD-RAM
Power Supply
DC +5V / 1.3A
Voltage Allowance
DC +5V
(5% (Operating), DC +5V(8% (Start Up))
Chapter 1
21
Combo Drive Module
Item
Specification
Manufacturer and Model
Sony NEC Optiarc BC-5500S-AR
Type
Drawer loading
Interface
SATA
Data Transfer Modes
•
PIO mode
•
DMA
•
Ultra DMA33
Buffer Memory Size
4.5 MB
Maximum Write Speed
11 Mbytes/sec
Maximum Read Speed
9 Mbytes/sec
Formats Supported
Read
•
BD-Video (12cm, Single and Dual Layer), BD-ROM (12cm, Single
and Dual Layer)
•
DVD-Video (8cm/12cm, Single and Dual Layer), DVD-ROM (8cm/
12cm, Single and Dual Layer), Multi-Boarder, Multi-Session
CD Write
•
CD-R Media (48x/40x/32x/24x/16x/8x) Mitsubishi (Verbatim), TaiyoYuden, Mitsui, Ricoh, Fuji film, Sony, Hitachi Maxell, Memorex,
RITEK, CMC, P.V.C, JVC, SKC, ACER, Prime Disc, TDK
•
CD-RW Media (10x/4x) Ricoh, Mitsubishi (Verbatim), ACER,
OPTROM, Memorex, P.V.C, RITEK, CMC, LEADDATA, GigaStorage,
Prodisc, Fornex, Samsung, Philips
DVD Write
•
DVD+R Media (16x/8x/4x/2.4x) Taiyo-Yuden, Mitsubishi (Verbatim),
Ricoh, TDK
•
DVD+R Double Layer Media (8x/2.4x) Mitsubishi (Verbatim)
•
DVD+RW Media (8x/4x/2.4x) Mitsubishi (Verbatim), Ricoh, TDK
•
DVD-R Media (16x/8x/4x/2x) Mitsubishi (Verbatim), TDK, TaiyoYuden, PVC, Fuji Film, Ritek
•
DVD-R DL Media (8x/4x) Mitsubishi (Verbatim)
•
DVD-RW Media (6x/4x/2x/1x) JVC, PVC, Mitsubishi (Verbatim), TDK
•
DVD-RAM Ver2.2 Media (5x/3x/2x) Panasonic, Hitachi Maxell
Power Supply
+5V (DC)
Voltage Allowance
+5V (DC) ±5%
Audio Interface
Item
22
Specification
Audio Controller
Realtek ALC888S
Audio onboard or optional
Onboard
Mono or Stereo
Stereo
Resolution
DAC support 16/20/24bit, ADC support 16/20bit
Compatibility
Microsoft WLP3.02, Vista WaveRT, Dolby Home Theater
Sampling rate
DAC support 192Kbit, ADC support 96Kbit sample rate
Internal microphone
Analog Microphone*1
Internal speaker / Quantity
2W Internal speakers*2, Subwoofer*1
Chapter 1
Video Memory
Item
Specification
Chipset
RS780MN for UMA, M82ME-XT/M86ME for Discrete
Memory size
Up to 512MB for Discrete SKU
USB Interface
Item
Specification
Chipset
AMD SB700
USB Compliancy Level
Support USB 1.1 and 2.0
OHCI
5 OHCI and 2 EHCI controller
Number of USB port
Chipset support 12 port(4 external port on the system)
Location
2 ports on the right side, 2 ports on the left side
Serial port function control
N/A
System Board Major Chips
Item
Controller
Core logic
AMD RS780MN+SB700
VGA
AMD RS780MN for UMA, M82ME-XT/M86ME for Discrete
LAN
Broadcom BCM5764MKMLG
USB 2.0
SB700 embedded
Super I/O controller
N/A
MODEM
Foxconn T60M955
Bluetooth
Broadcom 2045
Wireless 802.11 b+g
Foxconn XB63 and 4312
PCMCIA/ 5 in 1 Card Reader
JMicron JMB385
Audio Codec
Realtek ALC888S
Keyboard
Item
Specification
Keyboard controller
LPC interface
Total number of keypads
88-/89-/93-key
Windows logo key
Yes
Internal & external keyboard work
simultaneously
Plug USB keyboard to the USB port directly: Yes
Battery 6 Cell
Item
Vendor & model name
Specification
Sanyo &
AS07B31
Sony &
AS07B41
Panasonic &
AS07B51
Simplo &
AS07B71
Battery Type
Li-ion
Li-ion
Li-ion
Li-ion
Pack capacity
4500mAh
4500mAh
4500mAh
4500mAh
Number of battery cell
6cell
6cell
6cell
6cell
Package configuration
3S2P
3S2P
3S2P
3S2P
Normal voltage
10.8V
11.1V
11.1V
11.1V
Charge voltage
12.6V
12.6V
12.6V
12.6V
Chapter 1
23
Battery 8 Cell
Item
Specification
Vendor & model name
Sanyo &
AS07B32
Sony &
AS07B42
Panasonic &
AS07B52
Simplo &
AS07B72
Battery Type
Li-ion
Li-ion
Li-ion
Li-ion
Pack capacity
4800mAh
4800mAh
4800mAh
4800mAh
Number of battery cell
8cell
8cell
8cell
8cell
Package configuration
4S2P
4S2P
4S2P
4S2P
Normal voltage
14.8V
14.8V
14.8V
14.8V
Charge voltage
16.8V
16.8V
16.8V
16.8V
LCD 15.4”
Item
Specification
Vendor/model name
Chimei N154I3-L03, Samsung LTN154AT01A01, AUO B154EW08 V1(HW 3A), LG.Philips
LP154WX4
Screen Diagonal (mm)
391
Active Area (mm)
331.2 X 207.0
Display resolution (pixels)
1280x (RGB) x 800
Pixel Pitch
0.2588 (H) x 0.2588 (V)
Pixel Arrangement
RGB vertical stripe
Display Mode
Typical White Luminance (cd/m
also called Brightness
24
Normally white
2)
220 cd/m2 (Typ.5 point)
Luminance Uniformity
1.25 max. (5 points)
Contrast Ratio
300 Min
400 typical
Response Time (Optical Rise
Time/Fall Time) msec
Rising: 6
Falling: 2
Nominal Input Voltage VDD
+3.3 typ.
Typical Power Consumption (watt)
6.0 max.(without inverter)
Weight (without inverter)
500 typ.
525 max.
Physical Size (mm)
344.0 typ. x 222.0 typ. x 6.1 max.
Electrical Interface
1 channel LVDS
Support Color
262K colors (RGB 6-bit)
Viewing Angle (degree)
Horizontal: Right/Left
Vertical: Upper/Lower
40/40
15/30
Temperature Range (°C)
Operating
Storage (shipping)
0 to +50
-20 to +60
Chapter 1
LCD Camera
Item
Specification
Vendor
Bison Electronics
Suyin
Model Name
BN30V4O7-010
CN0314-SN30-OV03-1
Type
Fixed
Fixed
Dimension (L x W x H mm)
W 9 * L 65 * H 5.3 mm
65* 9.0 * 5.30+/-0.20 mm
Sensor
Up to SXGA(1280x1024) size
CMOS sensor
OV7725 CMOS Sensor 350K
Pixel
Optical Size
1/4 inch
F/2.0
Pixel Resolution
640(H) X 480(V) VGA
640 x 480
Pixel Size
6.0µm X 6.0µm
6.0µm x 6.0µm
LCD Inverter
Item
Vendor & model name
Specification
YEC YNV-C02G
Brightness conditions
N/A
Input voltage (V)
9~20(V)
Input current (mA)
0.08~0.6
Output voltage (V, rms)
Typical 680Vrms
Output current (mA, rms)
2.0~6.8
Output voltage frequency (k Hz)
45~70
AC Adapter
Item
Specification
Input rating
100~240Vac, 50~60Hz
Maximum input AC current
1.7A
Inrush current
No damage
Efficiency
Meet EPA Energy Star level-4 requirement
System Power Management
ACPI mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned
off completely.
Working (G0/S0)
Individual devices such as the CPU and hard disc may be
power managed in this state.
Suspend to RAM (S3)
CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4)
Also called Hibernation Mode. System saves all system
states and data onto the disc prior to power off the whole
system.
Chapter 1
25
26
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility
There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.
Follow these instructions:
•
To choose a menu, use the left and right arrow keys.
•
To choose an item, use the up and down arrow keys.
•
To change the value of a parameter, press F5 or F6.
•
A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
•
Press Esc while you are in any of the menu options to go to the Exit menu.
In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
•
Chapter 2
27
Information
The Information screen displays a summary of your computer hardware information.
Information
Main
PhoenixBIOS Setup Utility
Advanced Security
Power Boot
AMD
Exit
CPU Type:
CPU Speed:
AMD Turion (tm) X2 Ultra Dual-Core Mobile ZM-84
2300 MHz
HDD Model Name:
HDD Serial Number:
ATAPI Model Name:
Hitachi HTS542525K9SA00 -(PM)
071110BB0F00WDGS1K4C
Slimtype DVD A DS8A2S
-(PS)
System BIOS Version:
VGA BIOS Version:
V1.01
V010.080.000.000.027965
Serial Number:
Asset Tag Number:
Product Name:
Manufacturer Name:
UUID:
33643636336236356663001B38E109DB
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter Select( Submenu
F9 Setup Default
F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter
28
Description
CPU Type
This field shows the CPU type and speed of the system.
CPU Speed
This field shows the speed of the CPU.
HDD Model Name
This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number
This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name
This field shows the model name of the Optical device installed in the system.
System BIOS Version
Displays system BIOS version (MP models display BIOS ver. 1.01).
VGA BIOS Version
This field displays the VGA firmware version of the system.
Serial Number
This field displays the serial number of this unit.
Asset Tag Number
This field displays the asset tag number of the system.
Product Name
This field shows product name of the system.
Manufacturer Name
This field displays the manufacturer of this system.
UUID Number
Universally Unique Identifier (UUID) is an identifier standard used in software
construction, standardized by the Open Software Foundation (OSF) as part of
the Distributed Computing Environment (DCE).
Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.
Information
Main
PhoenixBIOS Setup Utility
Advanced Security
Power Boot
System Time
System Date
[13:04:04]
[04/30/2008]
System Memory
Extended Memory
Video Memory
633 KB
4094 MB
256 MB
Quiet Boot
Network Boot
F12 Boot Menu
[Enabled]
[Enabled]
[Enabled]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter SelectXSubmenu
AMD
Exit
Item Specific Help
<Tab>, <Shift-Tab>, or
<Enter> selects field.
F9 Setup Default
F10 Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed with 24hour format.
Format: HH:MM:SS
(hour:minute:second)
System Date
Sets the system date.
Format MM/DD/YYYY
(month/day/year)
System Memory
This field reports the memory size of the system.
Memory size is fixed to 633 KB.
N/A
Extended Memory
This field reports the Extended Memory size.
Memory size is fixed to 4094 MB.
N/A
Video Memory
Shows the video memory size.
VGA Memory size =256 MB
N/A
Quiet Boot
Displays the logo screen while booting.
Option: Enabled or
Disabled
Network Boot
Enables, disables the system boot from LAN (remote
server).
Option: Enabled or
Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Enabled or
Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
29
Advanced
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.
Information
Main
PhoenixBIOS Setup Utility
Advanced
Security
Power Boot
XAdvanced Chipset Control
XASF Configuration
PS/2 Mouse
IDE Controller
SB Power Saving Feature:
On chip SATA
SATA Class ID
SATA IDE Combined mode
PATA Channel Config
ACHI ROM POST delay
[Auto Detec]
[Disabled]
[Enabled]
[Enabled]
[IDE-ACHI C]
[Disabled]
[SATA as pr]
[Disabled]
USB Host Controller:
Legacy USB Support:
Option ROM Placement
[Enabled]
[Enabled]
[Disabled]
Large Disk Access Mode:
Installed O/S:
Reset Configuration Data
Processor Assisted Virtualization:
[DOS]
[Other]
[No]
[Enabled]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter SelectXSubmenu
AMD
Exit
Item Specific Help
Select options for
Advanced Chipset
features.
F9 Setup Default
F10 Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
30
Description
Submenu Items
Advanced
Chipset Control
Enter the Advanced Chipset Control menu.
•
•
Advanced NB Options
Advanced SB Options
ASF
Configuration
Enter the ASF Configuration menu.
•
•
•
•
•
ASF OS Device Availability
Minimum Watchdog Timeout
BIOS Boot Timeout
OS Boot Timeout
Power-on wait time
PS/2 Mouse
Enable or Disable PS/2 Mouse port IRQ12.
Option: Auto Detect, Enabled, or
Disabled
IDE Controller
Configure the Integrated Local Bus IDE
Controller.
Option: Disabled, Both, or Primary
SB Power
Saving Feature
Enable SB Power Saving Feature.
Option: Enabled or Disabled
Chapter 2
Parameter
Description
Submenu Items
On chip SATA
Enable On chip SATA.
Option: Enabled or Disabled
SATA Class ID
Select the SATA Class ID.
Option: IDE-ACHI Class,
HyperFlash Class, IDE-HyperFlash
Class, IDE Native Mode, Raid Class,
ACHI Class, or IDE Legacy Mode
SATA IDE
Combined mode
Set SATA IDE Combined mode.
Option: Disabled or Enabled
PATA Channel
Config
Set the SATA channel as Primary or
Secondary channel.
Option: SATA as primary or SATA
as secondary
ACHI ROM
POST delay
Select SATA option ROM POST delay.
Option: Disabled, 7, 6, 5, 4, 3, 2, or
1 second(s) delay
USB Host
Controller
Enable or disable USB hardware.
Option: Enabled or Disabled
Legacy USB
Support
Enable support for Legacy Universal Serial
Bus.
Option: Enabled or Disabled
Option ROM
Placement
Determines which peripheral devices can
be booted.
NOTE: Changes to this setting can cause
the system to halt during boot.
Option: Disabled, Temporary, or
E000 Extend
Large Disk
Access Mode
Set the Large Disk Access mode. Different
O/S require different drive geometry
representations. Select Other for UNIX,
Novell NetWare, or other O/S.
Option: DOS or Other
Installed O/S
Set the most commonly used O/S on the
system.
Option: Other, Win2000, WinMe,
Win98, or Win95
Reset
Configuration
Data
Clear Extended System Configuration Data
(ESCD) area.
Option: No or Yes
Processor
Assisted
Virtualization
Enable the hardware visualization support.
Option: Enabled or Disabled.
Chapter 2
31
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Information
Main
PhoenixBIOS Setup Utility
Advanced Security Power Boot
Supervisor Password Is
User Password Is
HDD 0 Password Is
Clear
Clear
HDD Password Frozen
Set Supervisor Password
Set User Password
[Enter]
[Enter]
Power on Boot
[Disabled]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter SelectXSubmenu
AMD
Exit
Item Specific Help
Supervisor Password
controls acces to the
setup utility. It can
be used to boot up when
Password on boot is
enabled.
F9 Setup Default
F10 Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Supervisor Password Is
Shows the setting of the Supervisor password
Clear or Set
User Password Is
Shows the setting of the user password.
Clear or Set
HDD 0 Password Is
Shows the setting of the hard disk password.
Frozen
Set Supervisor Password
Press Enter to set the supervisor password. When
set, this password protects the BIOS Setup Utility
from unauthorized access. The user can not either
enter the Setup menu nor change the value of
parameters.
Set User Password
Press Enter to set the user password. When user
password is set, this password protects the BIOS
Setup Utility from unauthorized access. The user can
enter Setup menu only and does not have right to
change the value of parameters.
Password on Boot
Defines whether a password is required or not while
the events defined in this group happened. The
following sub-options are all requires the Supervisor
password for changes and should be grayed out if the
user password was used to enter setup.
Disabled or
Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
32
Chapter 2
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
33
Changing a Password
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears.
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses Enter.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
34
Chapter 2
Power
The Power screen allows the user to configure CPU and power management options.
Information
Main
PhoenixBIOS Setup Utility
Advanced Security
Power Boot
Enable ACPI (debug only):
High Precision Event Timer
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
[Yes[
[Yes]
F5/F6 Change Item
Enter SelectXSubmenu
AMD
Exit
Item Specific Help
En/Disable ACPI BIOS
(Advance Configuration
and Power Interface)
Debug only, remove this
option for production.
F9 Setup Default
F10 Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
Description
Option
Enable ACPI (debug only)
Enable or disable ACPI BIOS.
Yes or No
High Precision Event Timer
Enable or disable HPET.
Yes or No
Chapter 2
35
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Information
Main
PhoenixBIOS Setup Utility
Advanced
Security
Power Boot
Boot priority order:
1. IDE0 : Hitachi HTS542525K9SA00- (S
2. IDE1 : Slimtype DVD A DS8A2S- (S2
3. PCI LAN: MBA v11.0.3 Slot 0600
4. USB HDD :
5. USB FDD :
6. USB KEY :
7. USB CD/DVD ROM :
F1 Help
ESC Exit
36
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter Select XSubmenu
AMD
Exit
Item Specific Help
Use < ↑ > or < ↓ > to
select a device, then
press <F6> to move it
up the List, or <F5>
to move it down the
list. Press <Esc> to
escape the menu.
F9 Setup Default
F10 Save and Exit
Chapter 2
AMD
The AMD screen allows the user to configure memory, thermal management options, and device wakeup
behavior.
Information
Main
PhoenixBIOS Setup Utility
Advanced
Security
Power Boot
XCBS Options
XPBS Options
F1 Help
ESC Exit
Parameter
CBS Options
PBS Options
Chapter 2
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter Select XSubmenu
Description
Manage common platform BIOS settings.
AMD
Exit
Item Specific Help
These options are
common to all
platforms.
F9 Setup Default
F10 Save and Exit
Submenu Items
•
•
•
Power Management
Thermal Control
DDR2 Memory & Memory Controller
•
•
•
•
•
•
•
•
•
Primary Display
Parallel ATA
On chip SATA
USB Host Controller
USB3 Controller
Legacy USB Support
OSC Support
System Time Lag Workaround
Thermal Fan Control
37
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
Information
Main
PhoenixBIOS Setup Utility
Advanced Security
Power Boot
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter SelectXSubmenu
AMD
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
F9 Setup Default
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
38
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding
Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
•
New versions of system programs
•
New features or options
•
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the flash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
39
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1.
Press F2 during boot to enter the Setup Menu.
2.
Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move
USB HDD to position 1.
3.
Execute the JALB028.BAT batch file from C:\JALB0_JALC0\BIOS\JALB028A to update BIOS.
The flash process begins as shown.
4. In flash BIOS, the message Please do not remove AC Power Source displays.
NOTE: If the AC power is not connected, the following message displays.
Plug in the AC power to continue.
5.
40
Flash is complete when the message Flash programming complete displays.
Chapter 2
WinFlash Utility
Perform the following steps to use the WinFlash Utility:
1.
Double click the WinFlash executable.
The Destination Directory screen displays.
2.
Click Start. A warning screen displays.
3.
Click OK to begin the update. A progress screen displays.
4.
When the process is complete, close all programs and applications and reboot the system.
Chapter 2
41
Removing HDD Passwords
This section provide you with removing HDD/BIOS password method:
Remove HDD Password:
If you key in the wrong HDD password three time, HDD password error code displays on the screen.
To reset the HDD password, perform the following steps:
1.
From a DOS prompt, key in Unlock6.exe 10068 00 and press <Enter>.
The Unlock6 program runs.
42
2.
Select option 2, Upper case ASCII Code, and press <Enter>.
3.
Make a note of one of the displayed passwords, for example XUSVE29, as shown.
4.
Power off the system by holding down the power button for >4 seconds.
5.
Reboot the system and key in the chosen password to unlock the HDD.
Chapter 2
Remove BIOS Password:
•
If you key in wrong Supervisor Password for three time, “System Disabled” would display on the
screen. See the image below.
•
If you need to solve BIOS password locked problem, you can run BIOS_PW.EXE
1. Key in “bios_pw 14452 0”
2. Choose one upper-case string
•
Chapter 2
Reboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password.
43
44
Chapter 2
Removing BIOS Passwords:
To clear the password, perform the following steps:
1.
From a DOS prompt, Execute clnpwd.exe
2.
Press 1 or 2 to clean the desired password shown on the screen.
The onscreen message determines whether the function is successful or not.
Chapter 2
45
46
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
•
Wrist grounding strap and conductive mat for preventing electrostatic discharge
•
Flat screwdriver
•
Philips screwdriver
•
Plastic flat screwdriver
•
Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3
47
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.
4. Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
•
•
•
External module disassembly
Main unit disassembly
LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List
Screw
48
Quantity
M2.5*8 (NL)
15
M2.5*5 (NL)
22
M2.5*3 (NL)
2
M2*3 (NL)
36
M2.5*4 (NL)
2
M2*6 (NL)
4
M2*4-NI (NL)
5
M3*3 (NL)
4
M2*6.5
4
M2.5*5.0
2
M2.5*6.5
4
Part Number
Chapter 3
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you
on the components that need to be removed during servicing. For example, if you want to remove the main
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Screw List
Step
Screw
Quantity
Color
Memory Cover
M2.5*8 (NL)
4
Black
HDD Cover
M2*6 (NL)
2
Black
WLAN Cover
M2.5*8 (NL)
4
Black
WLAN Module
M2*3 (NL)
2
Black
WLAN Bracket
M2*3 (NL)
1
Black
TV Tuner Module
M2*3
2
Black
HDD Carrier
M3*3 (NL)
4
Silver
ODD Module
M2.5*5(NL)
1
Black
ODD Bracket
M2*3 (NL)
3
Black
Chapter 3
Part No.
49
Removing the Battery Pack
1. Turn computer over.
2. Slide the battery lock/unlock latch to the unlock position.
3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main
unit (2).
2
1
50
Chapter 3
Removing the SD dummy card
1. Push the SD dummy card in to eject it.
2. Grasp the card and pull it out from the slot.
Chapter 3
51
Removing the ExpressCard dummy card
1. Push the ExpressCard dummy card in to eject it.
2. Grasp the card and pull it out from the slot.
52
Chapter 3
Removing the Lower Covers
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the SD dummy card” on page 51.
3. See “Removing the ExpressCard dummy card” on page 52.
4. Remove the two screws from the memory and WLAN bays and loosen the two captive HDD bay screws.
Memory
Cover
HDD
Cover
WLAN
Cover
Step
Size
Quantity
Memory Cover
M2.5*8 (NL)
1
HDD Cover
M2.5*8 (NL)
2
WLAN Cover
M2.5*8 (NL)
1
Screw Type
5. Carefully open the memory cover.
Chapter 3
53
6. Remove the HDD cover as shown.
7. Remove the WLAN cover as shown.
54
Chapter 3
Removing the DIMM Modules
1. Remove the Battery Pack. See “Removing the Battery Pack” on page 50.
2. Remove the Memory Module cover See “Removing the Lower Covers” on page 53.
3. Push out the release latches on both sides of the DIMM socket to release the DIMM module.
4. Remove the DIMM module.
5. Repeat steps for the second DIMM module if present.
Chapter 3
55
Removing the WLAN Module
1. See “Removing the Battery Pack” on page 50.
2. Remove the WLAN cover. See “Removing the Lower Covers” on page 53.
3. Disconnect the antenna cables from the WLAN board.
4. Move the antenna cables away and remove the two screws on the WLAN board to release the WLAN board.
Step
WLAN Module
56
Size
M2*3 (NL)
Quantity
Screw Type
2
Chapter 3
5. Detach the WLAN board from the WLAN socket.
NOTE: When re-attaching the antenna to the WLAN board, make sure the cables are arranged under the
WLAN bracket.
Chapter 3
57
Removing the TV tuner Module
1. See “Removing the Lower Covers” on page 53.
1. Remove the securing screw, located on the WLAN bracket, and remove the bracket.
NOTE: Move the antenna cables out of the way to allow for easier access.
Step
WLAN Bracket
Size
M2*3 (NL)
Quantity
Screw Type
1
2. Remove the adhesive strip to release the cable.
NOTE: Do not throw away the adhesive strip it is necessary to secure the cable on the new module.
58
Chapter 3
3. Disconnect the cable from the TV tuner module.
4. Remove the two securing screws.
Step
TV Tuner Module
Size
M2*3 (NL)
Quantity
Screw Type
2
5. Remove the tv tuner module.
Chapter 3
59
Removing the Hard Disk Drive Module
1. See “Removing the Battery Pack” on page 50.
2. Remove the HDD cover, See “Removing the Lower Covers” on page 53.
3. Use the mylar tab to slide and lift up the hard disk drive module to remove.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
60
Chapter 3
4. Remove the four screws securing the hard disk to the carrier.
Step
HDD Carrier
Size
M3*3 (NL)
Quantity
Screw Type
4
5. Remove the HDD from the carrier.
Chapter 3
61
Removing the Optical Drive Module
1. Remove the Battery Pack. See “Removing the Battery Pack” on page 50.
2. Remove the Memory cover. See “Removing the Lower Covers” on page 53.
3. Remove the screw securing the ODD module.
Step
ODD Module
Size
M2.5*5(NL)
Quantity
Screw Type
1
4. Grasp the front panel of the ODD and pull to remove from the main unit.
62
Chapter 3
5. Remove the three screws securing the ODD bracket and remove the ODD bracket from the optical disk drive
module.
Step
ODD Bracket
Size
M2*3 (NL)
Quantity
Screw Type
3
6. Insert a pin in the eject hole of the ODD to eject the ODD tray.
7. Press down on the locking catch to release the ODD cover and remove.
Chapter 3
63
Main Unit Disassembly Process
Main Unit Disassembly Flowchart
Screw List
Step
Quantity
Switch Cover
M2*3 (NL)
2
LCD Module
M2.5*8(NL)
4
M2.5*5 (NL)
2
M2.5*8 (NL)
9
M2.5*5 (NL)
5
Upper Cover
64
Screw
Color
Part No.
Chapter 3
Step
Screw
Quantity
Finger Print Reader
M2*3 (NL)
1
Upper Right Saddle
M2*3 (NL)
2
Left Speaker Module
M2.5*4 (NL)
2
Upper left Saddle
M2.5*4 (NL)
2
Touch Pad Bracket
M2*3 (NL)
2
eKey Board
M2*3 (NL)
1
Switch Board
M2.5*4 (NL)
1
Right Speaker Module
M2.5*4 (NL)
2
TV Board
M2.5*4 (NL)
2
USB Board
M2.5*4 (NL)
2
Modem Module
M2*3 (NL)
1
Subwoofer
M2*3 (NL)
2
Mainboard
M2.5*5 (NL)
2
Thermal Module
M2*6.5
4
M2*L3
4
M2*4-NI (NL)
2
VGA Module
Chapter 3
Color
Part No.
65
Removing the Switch Cover
CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is
recommended that only fingers are used to remove the Switch Cover.
1. See “Removing the Battery Pack” on page 50.
2. Locate and remove the three securing screws as shown.
Step
Switch Cover
Size
M2*3(NL)
Quantity
Screw Type
3
3. Turn the computer over and open the LCD module fully to expose the Switch Cover.
4. Lift the Switch Cover as shown, leftside first.
5. Lift the Switch Cover clear of the chassis.
66
Chapter 3
Removing the Keyboard
1. See “Removing the Battery Pack” on page 50..
2. Push down on the two latches securing the keyboard to the upper case.
3. Turn the keyboard over and pull back the securing latch to release the FFC.
Chapter 3
67
Removing the Antenna
WARNING:Do not attempt to pull the antenna cables under the WLAN bracket to prevent stripping of the
cable.
1. See “Removing the WLAN Module” on page 56.
2. Remove the securing screw, located on the WLAN bracket, and remove the bracket.
NOTE: Move the antenna cables out of the way to allow for easier access.
3. Remove the Antenna Cables from the securing guides as shown.
68
Chapter 3
4. Using one hand, pull the cables completely through the battery housing.
NOTE: Do not remove the adhesive tape.
5. Push the cables through the chassis, then turn over the computer and pull them completely through.
Chapter 3
69
Removing the LCD Module
1. Remove the Antenna. Remove the Antenna. See “Removing the Antenna” on page 68.
2. Remove the two securing screws from the bottom of the chassis.
Step
LCD Module
Size
M2.5*8(NL)
Quantity
Screw Type
2
3. Turn the computer over. Disconnect the LCD, MIC and back light cables from the top panel.
MIC cable
LCD cable
Back light cable
70
Chapter 3
4. Remove the four securing screws (two on each side) connecting the LCD module.
Step
Size
Quantity
LCD Hinges
(Red call out)
M2.5*6 (NL)
2
LCD Hinges
(Blue call out)
M2.5*10 (NL)
2
Screw Type
5. Carefully remove the LCD module from the chassis.
Chapter 3
71
Removing the Upper Cover
1. Remove the LCD Module. See “Removing the LCD Module” on page 70.
2. Turn the computer over. Remove the nine screws on the bottom panel.
Step
Upper Cover
Size
M2.5*10 (NL)
Quantity
Screw Type
9
3. Turn the computer over. Remove the five screws on the top panel.
Step
Upper Cover
72
Size
M2.5*4 (NL)
Quantity
Screw Type
5
Chapter 3
4. Disconnect the seven cables from the mainboard as shown.
A
B
C
G
D
F
E
Disconnect A as shown.
Release the securing latches and disconnect B as
shown.
Release the securing latches and disconnect C as
shown.
Release the securing latches and disconnect D as
shown.
Chapter 3
73
Release the securing latches and disconnect E as
shown.
Release the securing latches and disconnect F as
shown.
Release the securing latches and disconnect G as shown.
5. Remove the upper cover by lifting upward from the chassis, rear edge first.
74
Chapter 3
6. Turn the upper cover over. The upper cover appears as follows.
Chapter 3
75
Removing the Finger Print Reader
1. See “Removing the Upper Cover” on page 72.
2. Remove the securing screw from the Finger Print Reader board, and ensure the FFC is free of the upper cover.
Step
Finger Print
Reader
Size
M2*3 (NL)
Quantity
Screw Type
1
3. Remove the board bracket from the Upper Cover.
4. Using your fingers, gently lift the Finger Print Reader board from the Upper Cover.
76
Chapter 3
Removing the Upper Right Saddle
1. See “Removing the Upper Cover” on page 72.
2. Remove the two securing screws from the upper saddle.
Step
Upper Right
Saddle
Size
M2*3 (NL)
Quantity
Screw Type
2
3. Grasp the upper saddle and lift up to remove.
Chapter 3
77
Removing the Left Speaker Module
1. See “Removing the Upper Cover” on page 72.
2. Remove the two securing screws from the left speaker.
Step
Left Speaker
Module
Size
M2.5*4 (NL)
Quantity
Screw Type
2
3. Grasp both ends of the mylar cover and carefully pull back to expose the speaker cable.
4. While holding the cover with one hand, pull back the speaker cable to remove it from the housing well.
78
Chapter 3
5. Remove the left speaker module as shown.
Removing the Upper Left Saddle
1. See “Removing the Upper Cover” on page 72.
2. Pull back the mylar cover to expose the top securing screw.
3. Remove the bottom securing screw.
4. While holding the cover back, remove the top securing screw.
Chapter 3
79
Step
Left Speaker
Module
Size
M2.5*4 (NL)
Quantity
Screw Type
2
5. Firmly lift and rotate the saddle counter-clockwise to remove, paying attention to the securing clip.
Removing the Touch Pad Bracket
1. See “Removing the Upper Cover” on page 72.
2. Disconnect the Touch Pad FFC from the Touch Pad board.
3. Move the Finger Print Reader FFC cable out of the way to prevent damage, and pull back the securing foil on
the bracket.
80
Chapter 3
4. Remove the two securing screws from the Touch Pad bracket.
Step
Touch Pad Bracket
Size
M2*3 (NL)
Quantity
Screw Type
2
5. Remove the Touch Pad bracket.
IMPORTANT:The Touch Pad cannot be removed individually. To replace the Touch Pad, replace the entire
Upper Cover.
Chapter 3
81
Removing the Launch Board
1. See “Removing the Upper Left Saddle” on page 79.
2. Grasp the Launch Board and lift up to remove from the Upper Cover.
Removing the Media Board
1. See “Removing the Upper Left Saddle” on page 79.
2. Pull the FFC out of the chassis.
3. Insert the FFC flush with the connector and press the locking lever down to secure.
4. Use a pry to lift the Media board out of the Upper Cover.
82
Chapter 3
IMPORTANT:Do not press on components to prevent damage.
Removing the eKey Board
1. See “Removing the Upper Right Saddle” on page 77.
2. Turn the Upper Cover over and remove the FFC.
3. Remove the single screw
Step
eKey Board
Chapter 3
Size
M2*3 (NL)
Quantity
Screw Type
1
83
4. Pry the eKey board off the Upper Cover.
5. Grasp the board and gently pull the FFC through the Upper Cover.
84
Chapter 3
Removing the Switch Board
1. See “Removing the Upper Cover” on page 72.
2. Remove the single securing screw.
Step
Switch Board
Size
M2.5*4 (NL)
Quantity
Screw Type
1
3. Lift the switch board and FFC up and away from the upper cover.
Chapter 3
85
Removing the Right Speaker Module
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 72.
2. Remove the two securing screws from the speaker module.
Step
Speaker
Size
M2.5*4 (NL)
Quantity
Screw Type
2
3. Disconnect the speaker cable from the mainboard.
4. Pull the cable completely through the housing, and remove the speaker module.
86
Chapter 3
Removing the TV Board
1. See “Removing the Upper Cover” on page 72.
2. Disconnect the antenna and cable from the board.
3. Remove the two securing screws from the TV board.
Step
TV Board
Size
M2.5*4 (NL)
Quantity
Screw Type
2
4. Remove the TV board from the lower base.
Chapter 3
87
Removing the Bluetooth Module
1. See “Removing the Upper Cover” on page 72.
2. Grasp the Bluetooth module and lift to remove.
3. Lift the Bluetooth module away from the base and disconnect the bluetooth cable.
88
Chapter 3
Removing the USB Board
1. See “Removing the Upper Cover” on page 72.
2. See “Removing the Bluetooth Module” on page 88.
3. Remove cable from the USB board.
4. Remove the two securing screws from the USB board and lift clear of the chassis.
Step
USB board
Chapter 3
Size
M2.5*4 (NL)
Quantity
Screw Type
2
89
Removing the Modem Module
1. See “Removing the Upper Cover” on page 72.
2. Remove securing screw from the modem module.
Step
Modem Module
Size
M2*3 (NL)
Quantity
Screw Type
1
3. Lift the module and disconnect the modem cable as shown in the following images.
90
Chapter 3
Removing the Subwoofer Module
1. See “Removing the Upper Cover” on page 72.
2. Disconnect the subwoofer cable as shown.
3.
Remove the two securing screws from the subwoofer module and lift the subwoofer clear of the chassis.
Step
Subwoofer
Chapter 3
Size
M2*3 (NL)
Quantity
Screw Type
2
91
Removing the Main Board
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Keyboard” on page 67.
3. See “Removing the LCD Module” on page 70.
4. See “Removing the Upper Cover” on page 72.
5. Disconnect the three cables from the bottom right of the mainboard as shown.
6. Disconnect the two cables from the top right of the mainboard as shown.
92
Chapter 3
7. Remove the two securing screws from the Mainboard.
Step
Mainboard
Size
M2.5*5 (NL)
Quantity
Screw Type
2
8. Remove the main board, rightside first, as shown.
9. Lift the power jack clear of power port on the Lower Cover.
Chapter 3
93
Removing the RJ-11 Port
1. See “Removing the Upper Cover” on page 72.
2. See “Removing the Right Speaker Module” on page 86.
3. See “Removing the Main Board” on page 92.
4. Remove the RJ-11 cable from its housing.
5. Using the tweezers to grasp the end of the cable to detach from the base.
6. Insert the tweezers in the RJ-11 port and push up to detach and lift the port from the base.
94
Chapter 3
Removing the Thermal Module
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the LCD Module” on page 70.
3. See “Removing the Upper Cover” on page 72.
4. See “Removing the Main Board” on page 92.
5. Remove the eight securing screws from the Thermal Modules.
Step
Size
Quantity
CPU Thermal
Module
(red callout)
M2*6.5
4
VGA Thermal
Module
(blue callout)
M2*L3
4
Screw Type
6. Disconnect the fan module cable from mainboard.
Chapter 3
95
7. Lift the Thermal Module clear of the Mainboard.
96
Chapter 3
Removing the CPU
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Upper Cover” on page 72.
3. See “Removing the Main Board” on page 92.
4. See “Removing the Thermal Module” on page 95.
5. Using a flat screwdriver, turn the CPU socket latch counter-clockwise 180° to release the CPU.
6. Lift the CPU clear of the Mainboard.
Chapter 3
97
Removing the VGA Module
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Upper Cover” on page 72.
3. See “Removing the Main Board” on page 92.
4. Remove the two securing screws from the VGA Module.
Step
VGA Module
Size
M2*4-NI (NL)
Quantity
Screw Type
2
5. The VGA module lifts automatically from the mainboard. Remove the VGA Module as shown.
98
Chapter 3
LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Screw List
Step
Screw
LCD Bezel
M2.5*5 (NL)
4
Black
Inverter Board
M2.5*5 (NL)
1
Black
Camera Module
M2*3 (NL)
2
Black
Camera Board
M2*3 (NL)
1
Black
LCD Panel
M2.5*5 (NL)
2
Black
LCD Brackets
M2*3 (NL)
8
Black
Chapter 3
Quantity
Color
Part No.
99
Removing the LCD Bezel
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the LCD Module” on page 70.
3. Remove the two upper and two lower bezel screw caps. Remove the four securing screws from the LCD
module.
Step
LCD Bezel
4.
100
Size
M2.5*5 (NL)
Quantity
Screw Type
4
Lift up the bezel, topside first, and remove it from the LCD Module.
Chapter 3
Removing the Inverter Board
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the LCD Module” on page 70.
3. See “Removing the LCD Bezel” on page 100.
4. Remove the securing tapes from the left and right sides of the Inverter board as shown.
5.
Remove the two securing screws from the Inverter board and lift the board clear of the LCD Module.
Step
Inverter Board
Chapter 3
Size
M2.5*6 (NL)
Quantity
Screw Type
2
101
6. Disconnect the left and right Inverter board cables as shown.
102
Chapter 3
Removing the Camera Module
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Lower Covers” on page 53.
3. See “Removing the WLAN Module” on page 56.
4. See “Removing the Keyboard” on page 67.
5. See “Removing the LCD Module” on page 70.
6. See “Removing the LCD Bezel” on page 100.
7. Disconnect the Camera Module cable as shown.
8. Remove the two securing screws from the Camera Module bracket.
Step
Camera Module
bracket
Chapter 3
Size
M2*3 (NL)
Quantity
Screw Type
2
103
9. Lift the Camera Module clear of the LCD Module.
10. Remove the securing screw from the camera board.
Step
Camera Board
Size
M2*3 (NL)
Quantity
Screw Type
1
11. Remove the camera board from the bracket.
104
Chapter 3
Removing the LCD Panel
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Lower Covers” on page 53.
3. See “Removing the WLAN Module” on page 56.
4. See “Removing the Keyboard” on page 67.
5. See “Removing the LCD Module” on page 70.
6. See “Removing the LCD Bezel” on page 100.
7. Remove the two securing screws from the LCD Module.
Step
LCD Panel
Size
M2.5*6 (NL)
Quantity
Screw Type
2
8. Lift the LCD Panel clear of the LCD Module.
Chapter 3
105
Removing the LCD Brackets and FPC Cable
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Lower Covers” on page 53.
3. See “Removing the WLAN Module” on page 56.
4. See “Removing the Keyboard” on page 67.
5. See “Removing the LCD Panel” on page 105.
6. Turn the LCD panel over to expose the rear. Disconnect the cable from the LCD Panel using the tab provided.
7. Grip the FPC cable and lift upward to detach the adhesive pads.
8. Remove the eight securing screws (four on each side) from the LCD Panel brackets.
Step
LCD Brackets
Size
M2*3 NL
Quantity
Screw Type
8
9. Remove the LCD brackets by pulling away from the LCD Panel.
106
Chapter 3
Removing the Antennas
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Lower Covers” on page 53.
3. See “Removing the WLAN Module” on page 56.
4. See “Removing the LCD Panel” on page 105.
5. Remove the strips holding the antenna cables in place. Ensure the cables are free from obstructions.
6. Remove the tabs securing the left and right antennas to the LCD module.
7. Remove the antenna cables and assembly from the LCD module.
Chapter 3
107
Removing the MIC Module
1. See “Removing the Battery Pack” on page 50.
2. See “Removing the Lower Covers” on page 53.
3. See “Removing the WLAN Module” on page 56.
4. See “Removing the LCD Panel” on page 105.
5. Remove the strips holding the MIC Module cable in place. Ensure the cable is free from obstructions.
6. Remove the MIC cable and Module from the LCD module.
108
Chapter 3
LCD Module Reassembly Procedure
Replacing the LCD Panel
1. Align the LCD brackets with the eight screw holes (four on each side) on the LCD Panel as shown.
2. Secure the LCD brackets to the LCD panel.
3. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown.
Chapter 3
109
4. Replace the MIC cable under the mylar tab strips, and replace the MIC as shown. Secure the cable by
pressing down on the strips.
5. Replace the antenna cables and assembly.
6. Replace the tabs securing the left and right antennas to the LCD module.
7. Replace the strips holding the antenna cables in place. Ensure the cables are free from obstructions.
110
Chapter 3
8. Secure the cable by pressing down on the securing 9. Replace the two securing screws on the LCD
strip.
Module.
10. Replace the camera board in the bracket.
11. Replace the securing screw on the camera board.
12. Replace the Camera Module in the bottom cover.
13. Replace the two securing screws on the Camera
Module bracket.
Chapter 3
111
14. Connect the Camera Module cable as shown.
15. Connect the left and right Inverter board cables as
shown.
16. Connect the left and right Inverter board cables as shown.
17. Replace the inverter board and secure with the two provided screws.
112
Chapter 3
18. Replace the securing tapes from the left and right sides of the Inverter board as shown.
NOTE: Tuck the cables securely to prevent damage to the cables or module.
Replacing the LCD Bezel
1.
Align the edge of the bezel with the bottom cover and replace the LCD Module.
2. Replace the two upper and two lower bezel screw caps. Remove the four securing screws from the LCD
module.
Chapter 3
113
Main Module Reassembly Procedure
Replacing the VGA Module
1. Insert the VGA Module as shown.
2. Replace the two securing screws on the VGA
Module.
Replacing the CPU
1. Carefully turn the mainboard upside down (CPU
2. Using a flat-tipped screw driver, lock the CPU in
side up), and insert the CPU into the CPU bracket
the socket as shown.
as shown.
114
Chapter 3
Replacing the Thermal Module
1. Align and place the Thermal Module in the
mounting as shown.
2. Connect the fan module cable to the mainboard.
3. Replace the eight securing screws from the Thermal Module.
Replacing the RJ-11 Port
1. Insert the RJ-11 port into the base as shown.
Chapter 3
2. Using the tweezers, grasp the end of the cable and
press down to attach it to the base.
115
3. Replace the RJ-11 cable in its housing.
116
Chapter 3
Replacing the Mainboard
1. Replace the power jack in the Lower Cover.
2. Gently lower the mainboard, leftside first, on the
lower base. Ensure the screw sockets are aligned.
3. Ensure that the Mainboard is face up (the Heatsink and CPU are not visible). Place the Mainboard in the
chassis, rear edge first, and press down to install. Replace the two securing screws as shown.
NOTE: Make sure the I/O ports are positioned correctly through the lower cover, and the screw sockets are
visible through the mainboard.
4. Connect the two cables on the top right of the
mainboard as shown.
Chapter 3
5. Connect the three cables from the bottom right of
the mainboard as shown.
117
Replacing Subwoofer Module
6. Locate the Subwoofer on the lower cover, and replace the two securing screws.
7. Connect the subwoofer cable as shown.
Replacing the Modem Module
1. Connect the modem cable and locate it over the screw socket.
2. Insert module in mainboard.
118
Chapter 3
3. Replace the securing screw on the modem module.
Replacing the USB Board
1. Angle the right side of the USB board into the lower base. Align the screw sockets and replace the two
securing screws.
2. Replace the cable on the USB board.
Chapter 3
119
Replacing the Bluetooth Board
1. While holding the Bluetooth module, connect the
cable as shown.
2. Position the module over the aligning pins and
insert in place.
Replacing the TV Board
1. Angle the TV board into the lower base and lower into position.
2. Replace the two securing screws on the TV board.
3. Connect the antenna and single cable to the board.
120
Chapter 3
Replacing the Right Speaker Module
1. Replace the speaker module and insert the cable completely through the housing as shown.
2. Connect the speaker cable to the mainboard.
Chapter 3
121
3. Replace the two securing screws on the speaker module.
Replacing the Switch Board
1. Position the Switch Board over the screw socket.
2. Replace the single securing screw.
Replacing the eKey Board
1. Insert the FFC through the Upper Cover.
122
Chapter 3
2. Insert the eKey board at an angle and press down to situate.
3. Replace the single screw
4. Turn the Upper Cover over and press the FFC down to secure in place.
Chapter 3
123
Replacing the Media Board
1. Insert the Media Board into the lower cover. If necessary, use a pry to press the board in place.
IMPORTANT:Do not press on components to prevent damage.
2. Insert the FFC flush with the connector and press the locking lever down to secure.
3. Insert the FFC through the chassis.
124
Chapter 3
Replacing the Upper Right Saddle
1. Insert the left edge into position and pivot the upper saddle in place.
2. Replace the two securing screws on the upper saddle.
Chapter 3
125
Replacing the Launch Board
1. Insert the left edge of the Launch Board into place 2. Insert the saddle in place, taking care to locate it
and pivot the board down in place.
over the alignment pins.
3. Replace the two securing screws.
4. Replace the mylar cover to secure the saddle.
Replacing the Finger Print Reader
1. Replace the Finger Print Reader board in the upper cover.
126
Chapter 3
2. Replace the bracket as shown.
Chapter 3
3. Replace the single securing screw.
127
Replacing the Touch Pad Bracket
IMPORTANT:The Touch Pad cannot be removed individually. To replace the Touch Pad, replace the entire
Upper Cover.
1. Replace the Touch Pad bracket.
2. Replace the two securing screws from the Touch
Pad bracket.
3. Replace the Finger Print reader FFC and secure
with the adhesive strips.
4. Replace the Touch Pad FFC as shown.
128
Chapter 3
Replacing the Left Speaker Module
1. Align and replace the Speaker Module in the upper 2. Grasp both ends of the mylar cover to expose the
case.
housing.
3. Replace the speaker cable as shown.
4. While holding the mylar cover back with one hand, 6. Replace the two securing screws on the left
speaker.
replace the speaker cable in its housing.
5. Replace the mylar cover to secure the cable.
Replacing the Upper Cover
1. Starting with the rear, align the upper cover with the lower cover, taking care to not force in place.
Chapter 3
129
2. Connect the seven cables on the mainboard as shown.
A
B
C
G
D
F
E
130
Chapter 3
3. Replace the five screws on the top panel.
4. Turn the computer over. Replace the nine screws on the bottom panel.
Replacing the LCD Module
1. Carefully align the LCD module over the hinge sockets and lower the module into the chassis.
Chapter 3
131
2. Replace the four securing screws (two on each side) securing the LCD module.
3. Connect the LCD, MIC and back light cables.
LCD cable
MIC cable
Back light cable
132
Chapter 3
4. Turn the computer over and replace the two securing screws on the bottom of the chassis.
Replacing the Antenna Cables
Ensure that the three Antenna cables pass through the Mainboard and are accessible from the underside of
lower cover.
1. Insert the Antenna Cables through the Upper
Cover. Make sure they are accessible from the
underside.
2. Pull the cables through.
3. Secure the cables in place as shown.
4. Place the cabling in the wiring conduit as shown.
Chapter 3
133
Replacing the Keyboard
1. Align the FFC with the connector and press the
latch down to secure.
2. Turn the keyboard over and press down to secure.
Replacing the Switch Cover
1. Insert the left side of the switch cover and angle
down in place.
2. Starting from the left, press down on the Switch
Cover to secure.
3. Turn the computer over and replace the three securing screws.
134
Chapter 3
Replacing the TV Tuner Module
4. Replace the tv tuner module.
5. Replace the two securing screws.
6. Connect the cable to the TV tuner module.
Chapter 3
135
7. Replace the adhesive strip to secure the cable.
8. Replace bracket and secure with provided screw.
136
Chapter 3
Replacing the WLAN Module
1. Insert the WLAN board into the WLAN socket.
2. Replace the two screws to secure the module.
3. Connect the two antenna cables to the module.
Replacing the Hard Disk Drive Module
1. Place the HDD in the HDD carrier.
Chapter 3
2. Replace the four screws to secure the carrier.
137
3. Insert the HDD, interface side first, until HDD firmly slides in place.
Replacing the DIMM Modules
NOTE: To replace DIMM Module 2, first remove DIMM Module 1. In this procedure, only DIMM Module 1 is
shown.
1. Insert the DIMM Module flush with the connector and press down to lock in place.
138
Chapter 3
Replacing the ODD Module
1. With the ODD tray in the eject position, replace the 2. Press the cover into the tray, bottom edge first, to
ODD cover on the new ODD Module.
secure.
3. Turn the ODD over and replace the three securing 4. Slide Module in chassis and press until Module is
screws.
flush with chassis.
5. Replace the single screw to secure the Module.
Chapter 3
139
Replacing the Lower Covers
1. Replace the Memory Cover.
2. Replace the single screw to secure in place.
3. Replace the WLAN Cover.
4. Replace the screw to secure in place.
5. Replace HDD Cover.
6. Replace the two screws to secure in place.
140
Chapter 3
Replacing the Express and SD Card Trays
1. Insert the Express Card and push into the slot until 2. Insert the SD Card and push into the slot until flush
flush with the chassis cover.
with the chassis cover.
Chapter 3
141
142
Chapter 3
Chapter 4
Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power On Issue
Page 144
No Display Issue
Page 145
LCD Failure
Page 147
Internal Keyboard Failure
Page 147
Touchpad Failure
Page 148
Internal Speaker Failure
Page 148
Internal Microphone Failure
Page 150
ODD Failure
Page 152
Rightside USB Failure
Page 155
Modem Failure
Page 155
WLAN Failure
Page 156
Acer EasyLaunch Button Failure
Page 156
Acer MediaTouch Failure
Page 157
Fingerprint Reader Failure
Page 157
Thermal Unit Failure
Page 158
HDTV Switch Failure
Page 158
Other Functions Failure
Page 159
Intermittent Failures
Page 160
Undermined Failures
Page 160
4.
If the Issue is still not resolved, see “Online Support Information” on page 193.
Chapter 4
143
Power On Issue
If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Computer Shutsdown Intermittently
If the system powers off at intervals, perform the following actions one at a time to correct the problem.
144
1.
Check the power cable is properly connected to the computer and the electrical outlet.
2.
Remove any extension cables between the computer and the outlet.
3.
Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly
into a known good electrical outlet.
4.
Disconnect the power and open the casing to check the Thermal Unit (see “Thermal Unit Failure” on page
158) and fan airways are free of obstructions.
5.
Disable the power management settings in the BIOS to ensure they are not the cause of the problem (see
“Power” on page 35).
6.
Remove all external and non-essential hardware connected to the computer that are not necessary to
boot the computer to the failure point.
7.
Remove any recently installed software.
8.
If the Issue is still not resolved, see “Online Support Information” on page 193.
Chapter 4
No Display Issue
If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
No POST or Video
If the POST or video doesn’t display, perform the following actions one at a time to correct the problem.
1.
Make sure that the internal display is selected. On this notebook model, switching between the internal
display and the external display is done by pressing Fn+F5. Reference Product pages for specific model
procedures.
2.
Make sure the computer has power by checking at least one of the following occurs:
•
Fans start up
•
Status LEDs light up
If there is no power, see “Power On Issue” on page 144.
3.
Drain any stored power by removing the power cable and battery and holding down the power button for
10 seconds. Reconnect the power and reboot the computer.
4.
Connect an external monitor to the computer and switch between the internal display and the external
display is by pressing Fn+F5 (on this model).
If the POST or video appears on the external display, see “LCD Failure” on page 147.
5.
Disconnect power and all external devices including port replicators or docking stations. Remove any
memory cards and CD/DVD discs. Restart the computer.
If the computer boots correctly, add the devices one by one until the failure point is discovered.
6.
Reseat the memory modules.
7.
Remove the drives (see “Disassembly Process” on page 48).
8.
If the Issue is still not resolved, see “Online Support Information” on page 193.
Chapter 4
145
Abnormal Video Display
If video displays abnormally, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and
should be replaced. See “Disassembly Process” on page 48.
3.
If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD
is faulty and should be replaced. See “Disassembly Process” on page 48.
4.
Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings.
NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness.
If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See
“Disassembly Process” on page 48.
5.
Check the display resolution is correctly configured:
a.
Minimize or close all Windows.
b.
If display size is only abnormal in an application, check the view settings and control/mouse wheel
zoom feature in the application.
c.
If desktop display resolution is not normal, right-click on the desktop and select
Personalize´ Display Settings.
d.
Click and drag the Resolution slider to the desired resolution.
e.
Click Apply and check the display. Readjust if necessary.
6.
Roll back the video driver to the previous version if updated.
7.
Remove and reinstall the video driver.
8.
Check the Device Manager to determine that:
9.
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
If the Issue is still not resolved, see “Online Support Information” on page 193.
10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts.
11. If the Issue is still not resolved, see “Online Support Information” on page 193.
Random Loss of BIOS Settings
If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a
time to correct the problem.
1.
If the computer is more than one year old, replace the CMOS battery.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power
and data cables between devices.
If the BIOS settings are still lost, replace the cables.
146
4.
If HDD information is missing from the BIOS, the drive may be defective and should be replaced.
5.
Replace the Motherboard.
6.
If the Issue is still not resolved, see “Online Support Information” on page 193.
Chapter 4
LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
Built-In Keyboard Failure
If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
Chapter 4
147
Touchpad Failure
If the Touchpad doesn’t work, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Internal Speaker Failure
If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
148
Chapter 4
Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check
the Device Manager to determine that:
•
The device is properly installed.
•
There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
3.
Roll back the audio driver to the previous version, if updated recently.
4.
Remove and reinstall the audio driver.
5.
Ensure that all volume controls are set mid range:
a.
Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.
b.
Click Mixer to verify that other audio applications are set to 50 and not muted.
6.
Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected
as the default audio device (green check mark).
NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices
(clear by default).
7.
Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure
the speakers.
8.
Remove and recently installed hardware or software.
9.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
10. Reinstall the Operating System.
11. If the Issue is still not resolved, see “Online Support Information” on page 193.
Chapter 4
149
Internal Microphone Failure
If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to
correct the problem.
1.
Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´
Sound and select the Recording tab.
2.
Right-click on the Recording tab and select Show Disabled Devices (clear by default).
3.
The microphone appears on the Recording tab.
4.
Right-click on the microphone and select Enable.
5.
Select the microphone then click Properties. Select the Levels tab.
6.
Increase the volume to the maximum setting and click OK.
7.
Test the microphone hardware:
8.
150
a.
Select the microphone and click Configure.
b.
Select Set up microphone.
c.
Select the microphone type from the list and click Next.
d.
Follow the onscreen prompts to complete the test.
If the Issue is still not resolved, see “Online Support Information” on page 193.
Chapter 4
HDD Not Operating Correctly
If the HDD does not operate correctly, perform the following actions one at a time to correct the problem.
1.
Disconnect all external devices.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
Run the Windows Vista Startup Repair Utility:
a.
insert the Windows Vista Operating System DVD in the ODD and restart the computer.
b.
When prompted, press any key to start to the operating system DVD.
c.
The Install Windows screen displays. Click Next.
d.
Select Repair your computer.
e.
The System Recovery Options screen displays. Click Next.
f.
Select the appropriate operating system, and click Next.
NOTE: Click Load Drivers if controller drives are required.
g.
Select Startup Repair.
h.
Startup Repair attempts to locate and resolve issues with the computer.
i.
When complete, click Finish.
If an issue is discovered, follow the onscreen information to resolve the problem.
4.
Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support.
5.
Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that
CD/DVD drive is set as the first boot device on the Boot menu.
6.
Ensure all cables and jumpers on the HDD and ODD are set correctly.
7.
Remove any recently added hardware and associated software.
8.
Run the Windows Disk Defragmenter. For more information see Windows Help and Support.
9.
Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see
Windows Help and Support.
10. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
11. Replace the HDD. See “Disassembly Process” on page 48.
Chapter 4
151
ODD Failure
If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
ODD Not Operating Correctly
If the ODD exhibits any of the following symptoms it may be faulty:
•
Audio CDs do not play when loaded
•
DVDs do not play when loaded
•
Blank discs do not burn correctly
•
DVD or CD play breaks up or jumps
•
Optical drive not found or not active:
•
Not shown in My Computer or the BIOS setup
•
LED does not flash when the computer starts up
•
The tray does not eject
•
Access failure screen displays
•
The ODD is noisy
Perform the following general solutions one at a time to correct the problem.
152
1.
Reboot the computer and retry the operation.
2.
Try an alternate disc.
3.
Navigate to Start´ Computer. Check that the ODD device is displayed in the Devices with Removable
Storage panel.
4.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
a.
Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device
and click Enable.
b.
Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and
click Enable.
Chapter 4
c.
Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If
a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
d.
Check that there are no yellow exclamation marks against the items in DVD/CD-ROM drives. If a
device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
e.
If the exclamation marker is not removed from the item in the lists, try removing any recently installed
software and retrying the operation.
Discs Do Not Play
If discs do not play when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Check that the disc is correctly seated in the drive tray and that the label on the disc is visible.
2.
Check that the media is clean and scratch free.
3.
Try an alternate disc in the drive.
4.
Ensure that AutoPlay is enabled:
5.
a.
Navigate to Start´ Control Panel´ Hardware and Sound´ AutoPlay.
b.
Select Use AutoPlay for all media and devices.
c.
In the Audio CD and DVD Movie fields, select the desired player from the drop down menu.
Check that the Regional Code is correct for the selected media:
IMPORTANT:Region can only be changed a limited number of times. After Changes remaining reaches zero,
the region cannot be changed even Windows is reinstalled or the drive is moved to another computer.
a.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b.
Double-click DVD/CD-ROM drives.
c.
Right-click DVD drive and click Properties, then click the DVD Region tab.
d.
Select the region suitable for the media inserted in the drive.
Discs Do Not Burn Properly
If discs can not be burned, perform the following actions one at a time to correct the problem.
1.
2.
Ensure that the default drive is record enabled:
a.
Navigate to Start´ Computer and right-click the writable ODD icon. Click Properties.
b.
Select the Recording tab. In the Desktop disc recording panel, select the writable ODD from the
drop down list.
c.
Click OK.
Ensure that the software used for burning discs is the factory default. If using different software, refer to
the software's user manual.
Playback is Choppy
If playback is choppy or jumps, perform the following actions one at a time to correct the problem.
1.
2.
Check that system resources are not running low:
a.
Try closing some applications.
b.
Reboot and try the operation again.
Check that the ODD controller transfer mode is set to DMA:
a.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b.
Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0.
c.
Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is
checked and click OK.
Chapter 4
153
d.
Repeat for the other ATA Devices shown if applicable.
Drive Not Detected
If Windows cannot detect the drive, perform the following actions one at a time to correct the problem.
1.
Restart the computer and press F2 to enter the BIOS Utility.
2.
Check that the drive is detected in the ATAPI Model Name field on the Information page.
NOTE: Check that the entry is identical to one of the ODDs specified in “Hardware Specifications and
Configurations” on page 18.
3.
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 48.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
4.
Reseat the drive ensuring and all cables are connected correctly.
5.
Replace the ODD. See “Disassembly Process” on page 48.
Drive Read Failure
If discs cannot be read when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Remove and clean the failed disc.
2.
Retry reading the CD or DVD.
d.
Test the drive using other discs.
e.
Play a DVD movie
f.
Listen to a music CD
If the ODD works properly with alternate discs, the original disc is probably defective and should be
replaced.
3.
4.
154
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 48.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
Replace the ODD. See “Disassembly Process” on page 48.
Chapter 4
USB Failure (Rightside)
If the rightside USB port fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Modem Function Failure
If the internal Modem fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
Chapter 4
155
Wireless Function Failure
If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
EasyTouch Button Failure
If the Acer EasyTouch buttons fail, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
156
Chapter 4
MediaTouch Button Failure
If the Acer MediaTouch buttons fail, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Fingerprint Reader Failure
If the Fingerprint Reader fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Chapter 4
157
Thermal Unit Failure
If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
HDTV Switch Failure
If the HDTV Switch fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
158
Chapter 4
External Mouse Failure
If an external Mouse fails, perform the following actions one at a time to correct the problem.
1.
Try an alternative mouse.
2.
If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.
3.
If the mouse uses a USB connection, try an alternate USB port.
4.
Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.
5.
Restart the computer.
6.
Remove any recently added hardware and associated software.
7.
Remove any recently added software and reboot.
8.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
9.
Run the Event Viewer to check the events log for errors. For more information see Windows Help and
Support.
10. Roll back the mouse driver to the previous version if updated recently.
11. Remove and reinstall the mouse driver.
12. Check the Device Manager to determine that:
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
13. If the Issue is still not resolved, see “Online Support Information” on page 193.
Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or
Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective
FRUs:
1.
Check Drive whether is OK.
2.
Check Test Fixture is ok.
3.
Swap M/B to Try.
Chapter 4
159
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On
Issue” on page 144.):
160
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery pack
•
Hard disk drive
•
DIMM
•
CD-ROM/Diskette drive Module
•
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
•
System board
•
LCD assembly
Chapter 4
POST Codes Tables
These tables describe the POST codes, functions, phases, and components for the POST.
Chipset POST Codes
The following table details the chipset POST codes and functions used in the POST.
Code
Beeps
POST Routine Description
02h
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
16h
Initialize keyboard controller
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254
1Ah
8237
1Ch
timer initialization
DMA controller initialization
Reset Programmable Interrupt Controller
20h
1-3-1-1
Test DRAM refresh
22h
1-3-1-3
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 512 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx*
2Eh
1-3-4-3
RAM failure on data bits xxxx* of low byte of memory bus
2Fh
30h
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx* of high byte of memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
Chapter 4
161
Code
Beeps
POST Routine Description
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
POST device initialization
46h
2-1-2-3
Check ROM copyright notice
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
58h
2-2-3-1
Test for unexpected interrupts
59h
Initialize POST display service
5Ah
Display prompt Press F2 to enter SETUP
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to UserPatch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports.
162
Chapter 4
Code
Beeps
POST Routine Description
87h
Configure Motherboard Configurable Devices (optional)
88h
Initialize BIOS Data Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short beeps on checksum failure
99h
Check for SMART Drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
POST done - prepare to boot operating system
B4h
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
Chapter 4
163
Code
Beeps
POST Routine Description
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
D2h
Unknown interrupt
Code
Beeps
For Boot Block in Flash ROM
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
F4h
Initialize System Management Mode
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
* If the BIOS detects error 2C, 2E, or 30 (base 512K RAM error), it displays an additional word-bitmap (xxxx)
indicating the address line or bits that failed. For example, 2C 0002 means address line 1 (bit one set) has
failed. 2E 1020 means data bits 12 and 5 (bits 12 and 5 set) have failed in the lower 16 bits. Note that error 30
cannot occur on 386SX systems because they have a 16 rather than 32-bit bus. The BIOS also sends the
bitmap to the port-80 LED display. It first displays the check point code, followed by a delay, the high-order
byte, another delay, and then the low-order byte of the error. It repeats this sequence continuously.
164
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
Item
Description
Item
Description
JLVDS1
LCD Connector
JP13
FP/B Connector
JP23
Acer backlight Connector
JP27
Sub-Woofer Connector
JP16
Power/B Connector
JP9
USB/B Connector
JP8
TV/B Connector
JP10
Bluetooth Connector
JP21
Fun/B Connector
JMDC1
MDC Connector
JP14
Media/B Connector
JEXP1
Express Card Socket
JP19
Speaker (Left) Connector
JP17
BTN/B Connector
JP20
Speaker (Right) Connector
SW1
Touch pad (right) Button
JP15
Internal Keyboard Connector
SW2
Touch pad (left) Button
JP7
Touch Pad Connector
U10
South Bridge
Chapter 5
165
Bottom View
Item
166
Description
Item
Description
PJP1
AC-IN Connector
JSATA2
HDD Connector
JDOCK1
Dock Connector
JMINI2
TV-Tuner Card Connector
JRJ45
RJ45 Connector
JMINI1
Wireless Card Connector
JMXM1
MXM Board Connector
JSATA1
ODD Connector
JCRT1
CRT Connector
JDIMM2
Memory DIMM2 Connector
JHDMI1
HDMI Connector
JDIMM1
Memory DIMM1 Connector
JUSB1
USB Connector
PJP2
Battery Connector
JUSB2
USB Connector
JCPU1
CPU Socket
JLINE1
Line-In Jack
U25
North Bridge
JMIC1
MIC-In Jack
U37
Volume control wheel
JHP1
Head-Phone Connector
IR1
IR receiver
JREAD1
Card Reader Socket
Chapter 5
Clearing Password Check and BIOS Recovery
This section provide you the standard operating procedures of clearing password and BIOS recovery for
Aspire 5530. Aspire 5530 provide one Hardware Open Gap on main board for clearing password check, and
one Hotkey for enabling BIOS Recovery.
Clearing Password Check
Hardware Open Gap Description
Item
J1
Description
Clear CMOS Jumper
Steps for Clearing BIOS Password Check
If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is
necessary to bypass the password check, users need to short the HW Gap to clear the password by the
following steps:
•
Power Off a system, and remove HDD, AC and Battery from the machine.
•
Open the back cover of the machine, and find out the HW Gap on M/B as picture.
•
Use an electric conductivity tool to short the two points of the HW Gap.
•
Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the
system till BIOS POST finish. Then remove the tool from the HW Gap.
•
Restart system. Press F2 key to enter BIOS Setup menu.
If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and
try again.
NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).
•
Chapter 2
167
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:
BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous
BIOS flashing process failed.
BIOS Recovery Hotkey:
The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot
Block.
Steps for BIOS Recovery by Crisis Disk:
Before doing this, one Crisis Diskette should be prepared ready in hand. The Crisis Diskette could be made by
executing the Crisis Disk program in another system with Windows XP OS.
Follow the steps below:
1. Power Off failed system.
2. Attach a USB floppy drive to the failed system.
3. Copy jalb028.wph to tool's folder and rename it as BIOS.wph.
4. Execute wincris.exe to start the Crisis Disk Build.
5. Select Removable and click Start.
6. Select Format Disk and click Start.
168
Chapter 5
A progress screen displays.
7. The following message displays when the Crisis Diskette is created successfully.
8. Click OK to complete the process.
9. Insert the Crisis Disk in to the USB floppy drive attached to the BIOS flash failed system.
10. In the power-off state, press and hold Fn+Esc then press the Power button.
The system powers on and the Crisis BIOS Recovery process begins.
BIOS Boot Block begins restoring the BIOS code from the Crisis floppy disk to BIOS ROM on the failed
systems.
When the Crisis flash process is finished, the system restarts with a workable BIOS.
Update to the latest version BIOS for the system using the regular BIOS flashing process.
Chapter 2
169
170
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 5530. Refer to this chapter
whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6
171
Aspire 5530 Exploded Diagrams
Discrete SKU
Item
172
Description
1
Heat Pad
2
Strip Cover
3
F/P Board Bracket
4
F/P Board Module
5
Upper Case with F/P Reader
6
Mainboard
7
Thermal Unit with Fan Module
8
HDMI Module
9
Lower Case
10
Thermal Module
11
CPU
12
Heat Pad
Part Number
Chapter 6
UMA SKU
Item
Chapter 6
Description
1
Heat Pad
2
Strip Cover
3
F/P Board Bracket
4
F/P Board Module
5
Upper Case with F/P Reader
6
Mainboard
7
Fan Module
8
HDMI Module
9
Lower Case
10
Thermal Module
11
CPU
12
Heat Pad
Part Number
173
Aspire 5530 FRU List
Category
Description
Part Number
Adapter
ADAPTER 65W 3PIN DELTA SADP-65KB DFA
ADAPTER 65W 3PIN DELTA SADP65KB BFJA
ADAPTER 65W 3PIN LITE-ON PA-1650-02AC
ADAPTER 65W 3PIN HIPRO AC-OK065B13
ADAPTER 90W 3PIN DELTA ADP-90SB BBEA
ADAPTER 90W 3PIN DELTA ADP90SB BBEN
ADAPTER 90W 3PIN LITE-ON PA-1900-24AR
ADAPTER 90W 3PIN HIPRO AC-OL093B13P
Battery
BATTERY 6CELL 2.2AH SANYO SA SA 3S2P 4.4AH
BATTERY 6CELL 2.2AH SONY SY SY 3S2P 4.4AH
BATTERY 6CELL 2.2AH SIMPLO SP PA 3S2P 4.4AH
BATTERY 6CELL 2.2AH PANASONIC PA PA 3S2P 4.4AH
BATTERY 8CELL 2.4AH SANYO SA SA 4S2P 4.8AH
BATTERY 8CELL 2.4AH PANASONIC PA PA 4S2P 4.8AH
BATTERY 8CELL 2.4AH SIMPLO SP PA 4S2P 4.8AH
BATTERY 8CELL 2.4AH SONY SY SY 4S2P 4.8AH
Board
MODEM CARD
MODEM CARD-AUS
BLUE TOOTH
TV TUNER
WLAN CARD FOXCONN T60H976.00 (FW-06) 54M XB63
WLAN CARD FOXCONN T77H030.00 54MBPS BCM4312
VGA BOARD-M86ME
174
Chapter 6
Category
Description
Part Number
USB BOARD
TV BOARD W/RF
TV BOARD W/O RF
MEDIA BOARD
FINGER PRINT BOARD
POWER BOARD
FUNCTION BOARD
BUTTON BOARD
HDMI BOARD-UMA
Cable
RJ11 CABLE
BLUE TOOTH CABLE
USB CABLE
Chapter 6
175
Category
Description
Part Number
TV BOARD CABLE
MEDIA BOARD FFC
ANTENNA-R
ANTENNA-L
T/P FFC
POWER CORD US 3 PIN
27.TAVV5.001
POWER CORD EU 3 PIN
27.TAVV5.002
POWER CORD AUS 3 PIN
27.TAVV5.003
POWER CORD UK 3 PIN
27.TAVV5.004
POWER CORD CHINA 3 PIN
27.TAVV5.005
POWER CORD SWISS 3 PIN
27.TAVV5.006
POWER CORD ITALIAN 3 PIN
27.TAVV5.007
POWER CORD DENMARK 3 PIN
27.TAVV5.008
POWER CORD JP 3 PIN
27.TAVV5.009
POWER CORD SOUTH AFRICA 3 PIN
27.TAVV5.010
POWER CORD KOERA 3 PIN
27.TAVV5.011
POWER CORD ISRAEL 3 PIN
27.TAVV5.012
POWER CORD INDIA 3 PIN
27.TAVV5.013
POWER CORD TWN 3 PIN
27.TAVV5.014
POWER CORD ARGENTINA 3 PIN
176
Chapter 6
Category
Description
Part Number
Assembly
STRIP COVER
UPPER CASE ASSY W/FP
UPPER CASE ASSY W/O FP
T/P BRACKET
LOWER CASE ASSY W/TV
LOWER CASE ASSY W/OTV
UPPER SADDLE-R
UPPER SADDLE-L
MINI PCI BRACKET-L
FINGER PRINT BOARD BRACKET
EXPRESS DUMMY CARD
SD DUMMY CARD
Chapter 6
177
Category
Description
Part Number
RAM DOOR
HDD DDOR
MINI PCI DOOR
CPU
ODD
DVD SUPER MULTI DRIVE PIONEER DVR-TD08RS 0FA
DVD SUPER MULTI DRIVE TSST TS-L633A 0FA
DVD SUPER MULTI DRIVE PANASONIC UJ-870S 0FA
DVD SUPER MULTI DRIVE HLDS GSA-T50N 0FA
DVD SUPER MULTI DRIVE SONY AD-7560S 0FA
DVD SUPER MULTI DRIVE PLDS DS-8A2S 0FA
ODD BEZEL-SUPER MULTI
ODD BRACKET
BLUE RAY DRIVE SONY BC-5500S AR 0FA
ODD BEZEL-BR
ODD BRACKET
178
Chapter 6
Category
Description
Part Number
HDD
HDD SATA 120G 5400RPM HGST HTS542512K9SA00 0FA
HDD SATA 120G 5400RPM TOSHIBA MK1246GSX 0FA
HDD SATA 120G 5400RPM SEAGATE ST9120817AS 0FA
HDD SATA 120G 5400RPM WD WD1200BEVS-22UST0 0FA
HDD SATA 160G 5400RPM HGST HTS542516K9SA00 0FA
HDD SATA 160G 5400RPM HGST HTS543216L9A300 0FA
HDD SATA 160G 5400RPM TOSHIBA MK1646GSX 0FA
HDD SATA 160G 5400RPM TOSHIBA MK1652GSX 0FA
HDD SATA 160G 5400RPM SEAGATE ST9160827AS 0FA
HDD SATA 160G 5400RPM SEAGATE ST9160310AS 0FA
HDD SATA 160G 5400RPM WD WD1600BEVS-22ZCT0
HDD SATA 250G 5400RPM HGST HTS542525K9SA00 0FA
HDD SATA 250G 5400RPM TOSHIBA MK2546GSX 0FA
HDD SATA 250G 5400RPM SEAGATE ST9250827AS 0FA
HDD SATA 250G 5400RPM WD WD2500BEVS-22UST0 0FA
HDD SATA 320G 5400RPM WD WD3200BEVT-22ZCT0 0FA
HDD SATA 320G 5400RPM HGST HTS543232L9A300 0FA
HDD SATA 320G 5400RPM SEAGATE ST9320320AS 0FA
HDD CARRIER
Chapter 6
179
Category
Description
Part Number
Keyboard
KEYBOARD INTE(UI) BLACK AS
KEYBOARD ARE BLACK AS
KEYBOARD BE BLACK AS
KEYBOARD BZ BLACK AS
KEYBOARD CF BLACK AS
KEYBOARD CH BLACK AS
KEYBOARD CZ BLACK AS
KEYBOARD DM BLACK AS
KEYBOARD NL BLACK AS
KEYBOARD FR BLACK AS
KEYBOARD GR BLACK AS
KEYBOARD GK BLACK AS
KEYBOARD HG BLACK AS
KEYBOARD IT BLACK AS
KEYBOARD KO BLACK AS
KEYBOARD NW BLACK AS
KEYBOARD PO BLACK AS
KEYBOARD RU BLACK AS
KEYBOARD SA/CR BLACK AS
KEYBOARD SV BLACK AS
KEYBOARD SP BLACK AS
KEYBOARD SD/FN BLACK AS
KEYBOARD SW BLACK AS
KEYBOARD TI BLACK AS
KEYBOARD TR BLACK AS
KEYBOARD UK BLACK AS
KEYBOARD HB BLACK AS
KEYBOARD JP BLACK AS
KEYBOARD ND BLACK AS
KEYBOARD AR/FR BLACK AS
KEYBOARD CB BLACK AS
LCD Display
LCD PANEL G 15.4" WXGA AUO B154EW08 V1 3A
LCD PANEL G 15.4" WXGA CMO N154I3-L03
LCD PANEL G 15.4" WXGA LG LP154WX4-TLB4
LCD PANEL G 15.4" WXGA SEC LTN154AT01-A01
INVERTER
LCD CABLE
180
Chapter 6
Category
Description
Part Number
LCD COVER
LCD BEZEL
LCD BRACKET-R
LCD BRACKET-L
CAMERA MODULE-0.3M
CAMERA BRACKET
SCREW PAD
Mainboard
MB ASSY-UMA
MB ASSY-DIS
THERMAL PAD-L
THERMAL PAD-S
Chapter 6
181
Category
Description
Part Number
Memory
RAM 512MB DDRII 667 NANYA NT512T64UH8B0FN-3C
RAM 512MB DDRII 667 SAMSUNG M470T6464QZ3-CE6
RAM 512MB DDRII 667 SAMSUNG M470T6554EZ3-CE6
RAM 512MB DDRII 667 HYNIX HYMP164S64CP6-Y5
RAM 1G DDRII 667 NANYA NT1GT64U8HB0BN-3C
RAM 1G DDRII 667 HYNIX HYMP112S64CP6-Y5
RAM 1G DDRII 667 SAMSUNG M470T2864QZ3-CE6
RAM 1G DDRII 667 SAMSUNG M470T2864DZ3-CE6
RAM 2G DDRII 667 MICRON MT16HTF25664HY-667E1
RAM 2G DDRII 667 HYNIX HYMP125S64CP8-Y5
RAM 2G DDRII 667 SAMSUNG M470T5663QZ3-CE6
Heatsink
CPU THERMAL MODULE-DIS
CPU THERMAL MODULE-UMA
Speaker
SPEAKER-R
SPEAKER-L
SUB WOOFER
MIC SET
Misc
VGA MYLAR
NAME PLATE-AS5530
NAME PLATE-AS5230
182
Chapter 6
Category
Description
Part Number
RUBBER FOOT-L
RUBBER FOOT-S
Accessories
DVB-T ANTENNA
SMB-PAL CONNECTOR
PAL-F CONNECTOR
Screw List
Category
Description
SCREW
SCREW M2.5X4(NL)
SCREW
SCREW M2.5X6(NL)
SCREW
SCREW M2.5X10(NL)
SCREW
SCREW M 2D 2.5L K 4.05D NI NL
SCREW
SCREW M2D 3.0L K 8.0D(Ni)
SCREW
SCREW M2X3(NL)
SCREW
SCREW M2X5(Ni-NL)
SCREW
SCREW M3.0D 3.0L K 4.9D(Ni)
SCREW
SCREW CPU_THERMAL_SCREW_ASSY
SCREW
SCREW M2.0D 3L K 5D(Ni)
SCREW
SCREW F 4# 5L K 4.5D ZK NL +CR3+
Chapter 6
Part Number
183
Appendix A
Model Definition and Configuration
Aspire 5530 Series
RO
AS553
0G702
G2 5Mi
PA
USA
AS553
0G702
G2 5Mi
PA
Canada
LX.AR
V0X.0
02
AS553
0G702
G2 5Mi
PA
ACLAPortuguese
LX.AR
V0X.0
03
AS553
0G702
G2 5Mi
PA
ACLASpanish
LX.AR
V0X.0
04
AS553
0G702
G2 5Mi
PA
ACLASpanish
LX.AR
V0X.0
05
AS553
0G823
G3 2Bi
PA
ACLASpanish
LX.AR
V0X.0
09
Model
RO
Country
Acer
Part
no
Appendix A
Country
Acer
Part
no
LX.AR
V0X.0
01
Model
DIMM
1
DIM
M2
N15.4
WXGA
G8
SO1
GBII6
SO1
GBII
6
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
N
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
SO1
GBII
6
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
N
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
SO1
GBII
6
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
N
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
SO1
GBII
6
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
N
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
SO1
GBII
6
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
N
AES16
10
ATUZ
M82
N15.4
WXGA
G8
SO2
GBII6
SO1
GBII
6
N320
GB5.4
KS
NBD
C
B2XS
3rd WiFi
BG
BT 2.0
AES16
10
CPU
LCD
DIMM
1
DIM
M2
HDD 1
(GB)
ODD
Wireless
LAN
Bluetooth
Finger
Print
Description
CPU
LCD
AS5530G702G
25Mi
VHP32ATUS1
MC
82MEXTHM2
56CO 2*1G/
250/6L/5R/
CB_bg_FP_0.
3D_HG_EN32
AS5530G702G
25Mi
VHP32ATCA2
MC
82MEXTHM2
56CO 2*1G/
250/6L/5R/
CB_bg_FP_0.
3D_HG_FR31
AS5530G702G
25Mi EM
VHP32ATXC1
MC
82MEXTHM2
56CO 2*1G/
250/6L/5R/
CB_bg_FP_0.
3D_HG_XC22
AS5530G702G
25Mi EM
VHP32ATEA1
MC
82MEXTHM2
56CO 2*1G/
250/6L/5R/
CB_bg_FP_0.
3D_HG_ES22
AS5530G702G
25Mi EM
VHP32ATEA3
MC
82MEXTHM2
56CO 2*1G/
250/6L/5R/
CB_bg_FP_0.
3D_HG_ES22
AS5530G823G
32Bi EM
VHP32ATEA1
MC
82MEXTHM2
56CO 2G+1G/
320/BT/8L/5R/
CB_bg_FP_0.
3D_HG_ES22
Description
ATRM
70
HDD 1
(GB)
ODD
Wireless
LAN
Bluetooth
Finger
Print
184
RO
AS553
0G823
G3 2Bi
PA
ACLASpanish
AS553
0G823
G3 2Bi
PA
USA
LX.AR
V0X.0
06
AS553
0G823
G3 2Bi
PA
ACLAPortuguese
LX.AR
V0X.0
07
AS553
0G823
G3 2Bi
PA
Canada
LX.AR
V0X.0
08
AS553
0G701
G2 5Mi
TW
N
GCTWN
LX.AR
V0X.0
11
AS553
0G702
G2 5Mi
AA
P
Japan
LX.AR
V0X.0
12
AS553
0G702
G2 5Mi
AA
P
Thailand
LX.AR
V0X.0
13
AS553
0G701
G2 5Mi
TW
N
GCTWN
LX.AR
V0X.0
14
185
Country
Acer
Part
no
LX.AR
V0X.0
10
Model
DIMM
1
DIM
M2
N15.4
WXGA
G8
SO2
GBII6
SO1
GBII
6
N320
GB5.4
KS
NBD
C
B2XS
3rd WiFi
BG
BT 2.0
AES16
10
ATUZ
M82
N15.4
WXGA
G8
SO2
GBII6
SO1
GBII
6
N320
GB5.4
KS
NBD
C
B2XS
3rd WiFi
BG
BT 2.0
AES16
10
ATUZ
M82
N15.4
WXGA
G8
SO2
GBII6
SO1
GBII
6
N320
GB5.4
KS
NBD
C
B2XS
3rd WiFi
BG
BT 2.0
AES16
10
ATUZ
M82
N15.4
WXGA
G8
SO2
GBII6
SO1
GBII
6
N320
GB5.4
KS
NBD
C
B2XS
3rd WiFi
BG
BT 2.0
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
N
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
BT 2.0
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
SO1
GBII
6
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
BT 2.0
AES16
10
ATRM
70
N15.4
WXGA
G8
SO2
GBII6
N
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
BT 2.0
AES16
10
ATRM
70
N15.4
WXGA
G8
SO1
GBII6
N
N250
GB5.4
KS
NSM8
XS
3rd WiFi
BG
BT 2.0
AES16
10
Description
CPU
LCD
AS5530G823G
32Bi EM
VHP32ATEA3
MC
82MEXTHM2
56CO 2G+1G/
320/BT/8L/5R/
CB_bg_FP_0.
3D_HG_ES22
AS5530G823G
32Bi
VHP32ATUS1
MC
82MEXTHM2
56CO 2G+1G/
320/BT/8L/5R/
CB_bg_FP_0.
3D_HG_EN32
AS5530G823G
32Bi EM
VHP32ATXC1
MC
82MEXTHM2
56CO 2G+1G/
320/BT/8L/5R/
CB_bg_FP_0.
3D_HG_XC22
AS5530G823G
32Bi
VHP32ATCA2
MC
82MEXTHM2
56CO 2G+1G/
320/BT/8L/5R/
CB_bg_FP_0.
3D_HG_FR31
AS5530G701G
25Mi
VHP32ATTW 1
MC
82MEXTHM2
56CO 1*1G/
250/BT/8L/5R/
CB_bg_FP_0.
3D_HG_TC11
AS5530G702G
25Mi
VHP32AJP1
MC
82MEXTHM2
56CO 2*1G/
250/BT/6L/5R/
CB_bg_FP_0.
3D_HG_JA11
AS5530G702G
25Mi EM
VHP32ATTH1
MC
82MEXTHM2
56CO 1*2G/
250/BT/8L/5R/
CB_bg_FP_0.
3D_HG_TH22
AS5530G701G
25Mi
VHP32ATTW 1
MC
82MEXTHM2
56CO 1*1G/
250/BT/6L/5R/
CB_bg_FP_0.
3D_HG_TC11
ATUZ
M82
HDD 1
(GB)
ODD
Wireless
LAN
Bluetooth
Finger
Print
Appendix A
Appendix A
186
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home, Windows® XP Pro environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Aspire 5530 series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
187
Microsoft® Windows® Vista Environment Test
With Fingerprint Reader SKU
Vendor
Type
Description
Adapter Test
DELTA
90W
Adapter DELTA 90W 1.7x5.5x11 ADP-90SB BBEA LF level 4
DELTA
90W-DE
Adapter DELTA 90W 1.7x5.5x11 ADP-90SB BBEN (for OBL
Spec.) LV4 LF
Audio Codec Test
Realtek
ALC888S
Battery Test
SANYO
6CELL2.2
Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell
4400mAh Main COMMON Normal Type
SANYO
8CELL2.4
Battery SANYO AS-2007B Li-Ion 4S2P SANYO 8 cell
4800mAh Main COMMON
BT 2.0
Foxconn Bluetooth FOX_BRM_2.0 F/W 300
0.3M DV
Suyin 0.3M DV Camellia_2
5 in 1-Build in
5 in 1-Build in MS, MS Pro, SD, SC, XD
JMB385
JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/MSHG (1/4/8-bit) & xD (PCI Express)
AMD
AAQL60
CPU AMD Athlon64X2 QL60 PGA 1.9G 1M 638 35W Griffin
B1
AMD
ATRM70
CPU AMD TurionX2 RM70 PGA 2.0G 1M 638 35W Griffin B1
AMD
ATUZM80
CPU AMD TurionX2 ZM80 PGA 2.1G 2M 638 35W Griffin B1
AMD
ATUZM82
CPU AMD TurionX2 ZM82 PGA 2.2G 2M 638 35W Griffin B1
AMD
ATUZM84
CPU AMD TurionX2 ZM84 PGA 2.3G 2M 638 35W Griffin B1
AMD
ATUZM86
CPU AMD TurionX2 ZM86 PGA 2.4G 2M 638 35W Griffin B1
Bluetooth Test
Foxconn
Camera Test
Suyin
Card Reader Test
For all
Card Bus 1 Test
JMicron
CPU Test
Fingerprint Reader Test
Authentec
AES1610
Authentec AES1610
TOSHIBA
N120GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo BS
SATA I LF F/W:LB213J
SEAGATE
N160GB5.4KS
HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS
Crockett SATA LF F/W:0303
TOSHIBA
N160GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 160GB MK1652GSX Virgo - BS
SATA LF F/W:LV010J
SEAGATE
N250GB5.4KS
HDD SEAGATE 2.5" 5400rpm 250GB ST9250827AS Corsair
SATA LF F/W:3.AAA
HGST
N250GB5.4KS
HDD HGST 2.5" 5400rpm 250GB HTS543225L9A300
Falcon-B SATA LF F/W:C40C
HGST
N320GB5.4KS
HDD HGST 2.5" 5400rpm 320GB HTS543232L9A300
Falcon-B SATA LF F/W:C40C
HDD Test
188
Appendix B
Vendor
Type
Description
Keyboard Test
None
14_15KB-FV3 Black
Keyboard 14_15KB-FV3 Black McKinley/Eiger Standard
(Aspire Black)
BCM5764
Broadcom BCM5764
N15.4WXGAG8
LCD LPL 15.4" WXGA Glare LP154WX4-TLB4 LF 220nit 8ms
NANYA
SO1GBII6
SO-DIMM DDRII 667 1GB NT1GT64U8HB0BN-3C (0.09U)
NANYA
SO1GBII6
Memory NANYA SO-DIMM DDRII 667 1GB
NT1GT64UH8D0FN-3C LF 64*16 0.07um
NANYA
SO2GBII6
Memory NANYA SO-DIMM DDRII 667 2GB
NT2GT64U8HD0BN-3C LF 128*8 0.07um
MICRON
SO2GBII6
Memory MICRON SO-DIMM DDRII 667 2GB
MT16HTF25664HY-667E1 LF
NANYA
SO512MBII6
Memory NANYA SO-DIMM DDRII 667 512MB
NT512T64UH8B0FN-3C LF 32*16 0.09um
Fox+Con MC4Z 1.5_3.3V
Foxconn Conexant -Unizion 1.5_3.3v T60M955.02
LAN Test
Broadcom
LCD Test
LPL
Memory Test
Modem Test
Foxconn
Northbridge Chipset Test
AMD
AMDRS780MN
AMD RS780MN w/ HDCP EEPROM
SONY
NBDCB2XS
ODD SONY BD COMBO 12.7mm Tray DL 2X BC-5500S LF
W/O bezel SATA
TOSHIBA
NSM8XS
ODD TOSHIBA Super-Multi DRIVE 12.7mm Tray DL 8X TSL633A LF W/O bezel SATA
ODD Test
Remote Controller Test
Fomosa21
RC804V-B
Fomosa21 Remote Controller RC804V-B EU
Southbridge Chipset Test
AMD
AMDSB700
AMD SB700
McAfee
Antivirus application McAfee
86MEHM
AMD 86MEHM w/ HDCP w/o Macrovision
BT VoIP Xpress
Wistron Acer Xpress Card Phone Kit Rev 2.0
256M-GD3
256M GDDR2
PIFA
WiFi Antenna
3rd WiFi BG
Foxconn Atheros XB63 minicard b/g
Software Test
None
VGA Chip Test
AMD
VoIP Phone Test
Wistron
VRAM Test
ODM
WiFi Antenna Test
WNC
WLAN Test
Foxconn
Appendix B
189
Without Fingerprint Reader SKU
Vendor
Type
Description
Adapter Test
DELTA
90W-DE
Adapter DELTA 90W 1.7x5.5x11 ADP-90SB BBEN (for OBL
Spec.) LV4 LF
LITE-ON
90W
Adapter LITE-ON 90W 19V 1.7x5.5x11 Blue PA-1900-24AR LED
LF level 4
Audio Codec Test
Realtek
ALC888S
Battery Test
SANYO
6CELL2.2
Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell 4400mAh
Main COMMON Normal Type
SANYO
8CELL2.4
Battery SANYO AS-2007B Li-Ion 4S2P SANYO 8 cell 4800mAh
Main COMMON
Bluetooth Test
Foxconn
BT 2.0
Foxconn Bluetooth FOX_BRM_2.0 F/W 300
0.3M DV
Bison 0.3M DV Lotus_2
Camera Test
Bison
Card Reader Test
For all
5 in 1-Build in
5 in 1-Build in MS, MS Pro, SD, SC, XD
Card Bus 1 Test
JMicron
JMB385
JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/MS-HG (1/
4/8-bit) & xD (PCI Express)
AMD
AAQL60
CPU AMD Athlon64X2 QL60 PGA 1.9G 1M 638 35W Griffin B1
AMD
ATRM70
CPU AMD TurionX2 RM70 PGA 2.0G 1M 638 35W Griffin B1
AMD
ATUZM80
CPU AMD TurionX2 ZM80 PGA 2.1G 2M 638 35W Griffin B1
AMD
ATUZM82
CPU AMD TurionX2 ZM82 PGA 2.2G 2M 638 35W Griffin B1
AMD
ATUZM84
CPU AMD TurionX2 ZM84 PGA 2.3G 2M 638 35W Griffin B1
AMD
ATUZM86
CPU AMD TurionX2 ZM86 PGA 2.4G 2M 638 35W Griffin B1
SEAGATE
N120GB5.4KS
HDD SEAGATE 2.5" 5400rpm 120GB ST9120817AS Corsair
SATA LF F/W:3.AAA
WD
N120GB5.4KS
HDD WD 2.5" 5400rpm 120GB WD1200BEVS-22UST0 ML125
SATA LF F/W:01.01A01
SEAGATE
N160GB5.4KS
HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS Corsair
SATA LF F/W:3.AAA
TOSHIBA
N160GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 160GB MK1652GSX Virgo - BS
SATA LF F/W:LV010J
SEAGATE
N250GB5.4KS
HDD SEAGATE 2.5" 5400rpm 250GB ST9250827AS Corsair
SATA LF F/W:3.AAA
HGST
N250GB5.4KS
HDD HGST 2.5" 5400rpm 250GB HTS543225L9A300 Falcon-B
SATA LF F/W:C40C
WD
N320GB5.4KS
HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160
SATA LF F/W:11.01A11
CPU Test
HDD Test
Keyboard Test
190
Appendix B
Vendor
None
Type
Description
14_15KB-FV3 Black
Keyboard 14_15KB-FV3 Black McKinley/Eiger Standard (Aspire
Black)
BCM5764
Broadcom BCM5764
N15.4WXGAG8
LCD SAMSUNG 15.4" WXGA Glare LTN154AT01-A LF 220nit
8ms NON-bracket
NANYA
SO1GBII6
SO-DIMM DDRII 667 1GB NT1GT64U8HB0BN-3C (0.09U)
NANYA
SO1GBII6
Memory NANYA SO-DIMM DDRII 667 1GB NT1GT64UH8D0FN3C LF 64*16 0.07um
NANYA
SO2GBII6
Memory NANYA SO-DIMM DDRII 667 2GB NT2GT64U8HD0BN3C LF 128*8 0.07um
SAMSUNG
SO2GBII6
Memory SAMSUNG SO-DIMM DDRII 667 2GB M470T5663QZ3CE6 LF
HYNIX
SO512MBII6
Memory HYNIX SO-DIMM DDRII 667 512MB HYMP164S64CP6Y5 LF 64*16 0.065um
Fox+Con MC4Z
1.5_3.3V Aus
Foxconn Conexant -Unizion 1.5_3.3v AUS T60M955.0x
LAN Test
Broadcom
LCD Test
SAMSUNG
Memory Test
Modem Test
Foxconn
Northbridge Chipset Test
AMD
AMDRS780MN
AMD RS780MN w/ HDCP EEPROM
SONY
NBDCB2XS
ODD SONY BD COMBO 12.7mm Tray DL 2X BC-5500S LF W/O
bezel SATA
TOSHIBA
NSM8XS
ODD TOSHIBA Super-Multi DRIVE 12.7mm Tray DL 8X TSL633A LF W/O bezel SATA
ODD Test
Remote Controller Test
Fomosa21
RC804V-B
Fomosa21 Remote Controller RC804V-B EU
Southbridge Chipset Test
AMD
AMDSB700
AMD SB700
McAfee
Antivirus application McAfee
Software Test
None
VGA Chip Test
AMD
82MEXTHM
AMD 82MEXTHM w/ HDCP w/o Macrovision
VoIP Phone Test
Wistron
BT VoIP Xpress
Wistron Acer Xpress Card Phone Kit Rev 2.0
256M-GD2
256M GDDR2
VRAM Test
ODM
WiFi Antenna Test
WNC
PIFA
WiFi Antenna
3rd WiFi BG
Foxconn Atheros XB63 minicard b/g
WLAN Test
Foxconn
Appendix B
191
192
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
•
Service guides for all models
•
User's manuals
•
Training materials
•
Bios updates
•
Software utilities
•
Spare parts lists
•
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
•
Detailed information on Acer's International Traveler's Warranty (ITW)
•
Returned material authorization procedures
•
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
193
194
Appendix C
Index
A
55
DIMM Module
AFLASH Utility
Antennas
Display 4
39
display
107
hotkeys
B
14
E
Battery Pack
50
EasyTouch Failure
BIOS
83
eKey Board 83
Euro 15
Ekey Board
package 18
ROM size 18
ROM type 18
vendor 18
Version 18
External Module Disassembly
F
45
BIOS Supports protocol
18
Features 1
27–39
Advanced 30
Boot 36
Exit 38
Navigating 27
BIOS Utility
Fingerprint Reader Failure
39
FPC Cable 106
FRU (Field Replaceable Unit) List
171
H
Hard Disk Drive Module
60
HDD Passwords
Bluetooth module 88
Removing
Board Layout
42
HDTV Switch Failure
165
158
Hibernation mode
brightness
hotkeys
157
Flash Utility
Onboard Device Configuration 33
Power 35
Save and Exit 38
Security 32
System Security 38
Top View
49
Flowchart
BIOS Passwords
Removing
156
14
Hot Keys 12
hotkey
14
C
I
Cache
controller
size 18
Indicators 10
18
Camera Module
Intermittent Problems 160
103
150
Internal Speaker Failure 148
inverter board 101
Internal Microphone Failure
caps lock
on indicator
10
Common Problems
computer
on indicator
CPU
D
144
J
10
Jumper and Connector Locations
97
Top View
165
165
K
195
Keyboard
R
67
Keyboard Failure 147
Right Speaker Module
L
S
82
LCD Bezel 100
LCD Brackets 106
LCD Failure 147
Launch Board
speakers
hotkey
14
System
Block Diagram
LCD Module Disassembly
Test Compatible Components
Thermal Unit Failure
Top
M
Mainboard
hotkey
92
Built-in KB Failure 147
EasyTouch Buttons 156
Fingerprint Reader 157
HDTV Switch 158
Internal Microphone 150
Internal Speakers 148
LCD Failure 147
MediTouch Buttons 157
Modem 155
No Display 145
ODD 152
Other Failures 159
Power On 144
Thermal Unit 158
Touchpad 148
USB 155
WLAN 156
157
144
Model Definition 184
Modem Failure 155
Modem Module 90
Memory Check
N
No Display Issue
145
Notebook Manager
14
num lock
10
O
TV tuner
ODD Failure
58
U
152
Online Support Information
optical drive module
193
160
USB Failure (Rightside) 155
Undetermined Problems
62
P
utility
Panel
BIOS
5
Bottom
left 5
PC Card
148
Troubleshooting
10
MediaTouch Button Failure
on indicator
14
Touchpad Failure
media access
hotkey
80
touchpad
64
on indicator
158
165
Touch Pad Bracket
Main Unit Disassembly
Flowchart
4
T
99
LCD Panel 105
lower cover 53
Flowchart
27–39
V
9
VGA Module
10
Power On Failure
196
86
144
W
98
187
Windows 2000 Environment Test 188
Wireless Function Failure
WLAN Board
156
56
197
198
Download PDF

advertising