Acer 5940G Laptop User Manual

TravelMate 6492 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate 6492 service guide.
Date
2
Chapter
Updates
Copyright
Copyright © 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed “as is”. Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
3
Conventions
The following conventions are used in this manual:
4
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's “global” product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
5
6
Table of Contents
Chapter 1
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Operating system ..................................................................................................1
Platform and memory ............................................................................................1
Display and graphics .............................................................................................1
Storage subsystem ...............................................................................................1
Dimensions and Weight ........................................................................................1
Power Subsystem .................................................................................................2
Input devices .........................................................................................................2
Audio .....................................................................................................................2
Communication .....................................................................................................2
I/O Ports ................................................................................................................2
Environment ..........................................................................................................3
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Mainboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Top View ...............................................................................................................5
Bottom View ..........................................................................................................6
Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Front View .............................................................................................................8
Closed Front View .................................................................................................9
Left View .............................................................................................................10
Right View ...........................................................................................................11
Rear view ............................................................................................................11
Base view ............................................................................................................12
Indicators ............................................................................................................13
Easy-Launch Buttons ..........................................................................................14
Touchpad Basics ................................................................................................14
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Lock Keys and embedded numeric keypad ........................................................16
Windows Keys ....................................................................................................17
Hot Keys .............................................................................................................17
Special Key .........................................................................................................18
Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Acer eDataSecurity Management .......................................................................19
Acer eLock Management ....................................................................................21
Acer ePerformance Management .......................................................................22
Acer eRecovery Management ............................................................................23
Acer eSettings Management ...............................................................................24
Acer ePower Management .................................................................................25
Acer OrbiCam .....................................................................................................28
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Acer GridVista (dual-display compatible) ............................................................33
Launch Manager .................................................................................................34
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Chapter 2
System Utilities
47
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Navigating the BIOS Utility ..................................................................................47
Information ..........................................................................................................48
Main ....................................................................................................................49
Advanced ............................................................................................................51
Security ...............................................................................................................52
1
Boot .....................................................................................................................57
Exit ......................................................................................................................58
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Chapter 3
Machine Disassembly and Replacement
61
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Before You Begin ................................................................................................61
Disassembly Procedure Flowcharts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Main Unit Disassembly Flowchart .......................................................................62
LCM Module Disassembly Flowchart ..................................................................63
Main Unit Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing the Battery Pack ................................................................................64
Removing the CTO Cover ...................................................................................64
Removing the ODD .............................................................................................65
Removing the HDD .............................................................................................65
Removing the BTCB Screws ..............................................................................65
Removing the Memory Modules .........................................................................66
Removing the Wireless Card ..............................................................................67
Removing the Switch Cover ................................................................................68
Removing the Keyboard .....................................................................................69
Removing the Switch Board ................................................................................70
Removing the Antenna Cables ...........................................................................71
Removing the LCM Module ................................................................................73
Removing the TouchPad ....................................................................................74
Removing the Mainboard ....................................................................................74
Removing the Heatsink and Fan Module ............................................................76
Removing the CPU .............................................................................................77
LCM Module Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Removing the LCM Bezel ...................................................................................78
Removing the LCD Panel ...................................................................................79
LCM Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Replacing the LCD Panel ....................................................................................82
Replacing the LCM Bezel ...................................................................................84
Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Replacing the CPU .............................................................................................85
Replacing the Heatsink and Fan Module ............................................................85
Replacing the Mainboard ....................................................................................86
Replacing the TouchPad .....................................................................................88
Replacing the LCM Module .................................................................................88
Replacing the Antenna Cables ...........................................................................89
Replacing the Switch Board ................................................................................91
Replacing the Keyboard ......................................................................................91
Replacing the Switch Cover ................................................................................93
Replacing the Wireless Card ..............................................................................93
Replacing the Memory Modules .........................................................................94
Replacing the BTCB Screws ...............................................................................95
Replacing the HDD .............................................................................................95
Replacing the ODD .............................................................................................95
Replacing the CTO Cover ...................................................................................96
Replacing the Battery Pack .................................................................................96
Chapter 4
Troubleshooting
97
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
External Diskette Drive Check ............................................................................98
External CD-ROM Drive Check ..........................................................................98
2
Keyboard or Auxiliary Input Device Check ..........................................................98
Memory check .....................................................................................................98
Power System Check ..........................................................................................99
Touchpad Check ...............................................................................................100
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Chapter 5
Jumper and Connector Locations
117
Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Top View ...........................................................................................................117
Bottom View ......................................................................................................118
Connector Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Chapter 6
FRU (Field Replaceable Unit) List
133
TravelMate 6492 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
3G Cover Ass’y .................................................................................................134
Battery Ass’y .....................................................................................................135
BlueTooth Ass’y ................................................................................................136
BTCB Case Set Ass’y .......................................................................................137
BTCB Case Set .................................................................................................138
CPU Ass’y .........................................................................................................139
CTO Cover Set Ass’y ........................................................................................140
Display Ass’y .....................................................................................................141
Display Bezel Ass’y ...........................................................................................143
Display Rear Ass’y ............................................................................................144
HDD Ass’y .........................................................................................................145
Keyboard Ass’y .................................................................................................146
Memory Ass’y ...................................................................................................147
Modem Ass’y ....................................................................................................148
ODD Ass’y ........................................................................................................149
Switch Cover Set Ass’y .....................................................................................150
Touchpad Bracket Set Ass’y .............................................................................151
TPCB CaseSet Ass’y ........................................................................................152
Wireless Ass’y ..................................................................................................154
Parts List ...........................................................................................................155
Appendix A Model Definition and Configuration
166
TravelMate 6492 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
Appendix B Test Compatible Components
175
Test Peripherals for TravelMate 6492 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176
Appendix C Online Support Information
179
3
4
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
Operating system
•
Genuine Windows® VistaTM Capable
•
Genuine Windows® XP Professional (Service Pack 2)
Note: Windows® VistaTM Capable PCs come with Windows® XP installed, and can be upgraded to Windows®
VistaTM. For more information on Windows® VistaTM and how to upgrade, go to: Microsoft.com/windowsvista.
Platform and memory
•
Intel® Core™2 Duo mobile processor supporting Intel® 64 architecture and Intel® Virtualization
technology
•
Mobile Intel® GM965 Chipset (Northbridge), supporting Intel® Active Management Technology (AMT) 2.5
•
Intel® ICH8ME (South Bridge), featuring integrated 10/100/1000 GbE MAC with circuit breaker
•
Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules (dual-channel
support)
Display and graphics
•
14.1" WXGA TFT LCD, 1280 x 800 pixel resolution, supporting simultaneous multi-window viewing via
Acer GridVista™
•
Mobile Intel® GM965 Express Chipset with integrated 3D graphics, featuring Intel® Graphics Media
Accelerator (GMA) X3000 with Intel® Dynamic Video Memory Technology 4.0, supporting Microsoft®
DirectX® 9 and DirectX® 10
•
16.7 million colors
•
MPEG-2/DVD hardware-assisted capability (acceleration)
•
WMV9 (VC-1) and H.264 (AVC) support (acceleration)
•
S-video/TV-out (NTSC/PAL) support
Storage subsystem
•
80/120/160 GB hard disk drive with Acer DASP (Disk Anti-Shock Protection) enhancement
•
Acer MediaBay hot-swappable optical drive
•
•
8X DVD-Super Multi double-layer drive
5-in-1 card reader supporting Secure Digital™ (SD), MultiMediaCard (MMC), Memory Stick® (MS),
Memory Stick PRO™ (MS PRO), xD-Picture Card™ (xD)
Dimensions and Weight
•
339.4 (W) x 245 (D) x 35/39 (H) mm (13.36 x 9.65 x 1.37/1.54 inches)
•
2.56 kg (5.63 lbs.) with 6-cell battery pack and Acer MediaBay 6-cell 2nd battery pack
•
2.48 kg (5.46 lbs.) with 6-cell battery pack and optical drive
Chapter 1
1
Power Subsystem
•
ACPI 3.0 CPU power management standard: supports Standby and Hibernation power-saving modes
•
11.1V 3800 mAh Li-ion primary battery pack (6-cell)
•
3-pin 90 W AC adapter
•
2.5-hour rapid charge system-off
•
3.0-hour charge-in-use
Input devices
•
84-/88-key Acer FineTouch™ keyboard with 5º curve, inverted “T” cursor layout, 2.5 mm (minimum) key
travel
•
Dual navigation control, featuring Acer FineTrack™ with two FineTrack™ buttons and touchpad with 4way scroll button
•
Acer Bio-Protection fingerprint reader supporting Acer FingerNav 4-way control function
•
12 function keys, four cursor keys, two Windows® keys, hotkey controls, embedded numeric keypad,
international language support
•
Easy-launch buttons: Empowering Key, email, Internet, user programmable
•
Front-access communication switches: WLAN and Bluetooth®
Audio
•
Realtek ALC268 Chip
•
Intel® High Definition Audio support
•
Two built-in Acer 3DSonic stereo speakers
•
Built-in microphone
•
MS-Sound compatible
Communication
•
•
Acer Video Conference featuring:
•
Integrated Acer Crystal Eye webcam supporting enhanced Acer PrimaLite™ technology (for
selected models)
•
Optional Acer Bluetooth® VoIP phone
WLAN featuring:
•
•
Intel® Wireless WiFi Link 4965AGN (dual-band quadmode 802.11a/b/g/Draft-N) Wi-Fi CERTIFIED®
network connection, supporting Acer SignalUp™ with InviLink™ Nplify™ wireless technology, or
4965AG (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIED® network connection, supporting Acer
SignalUp™ wireless technology
WPAN featuring:
•
Bluetooth® 2.0+EDR (Enhanced Data Rate)
•
LAN featuring:
•
Modem featuring:
•
•
Gigabit Ethernet, supporting Intel® AMT 2.5, Wake-on-LAN ready
56K ITU V.92 with PTT approval, Wake-on-Ringready
I/O Ports
2
•
CRT port --- Support CRT monitor.
•
3 * USB 2.0 ports
•
MIC-In
Chapter 1
•
Line-In
•
RJ11/RJ45
•
DC Jack
•
1394 port
•
Cardbus
•
5 in 1 card reader
•
1* Serial port
•
EZ II / II+ connector
Environment
•
•
Temperature:
•
operating: 5°C to 35°C
•
Non-operating: -20°C to 65°C
Humidity (non-condensing):
•
operating: 20%~80%
•
Non-operating: 20%~80%
For a complete list of specifications see “Hardware Specifications and Configurations” on page 35.
Chapter 1
3
System Block Diagram
4
Chapter 1
Mainboard Layout
Top View
Chapter 1
Ite
m
Nam
e
Description
Ite
m
Nam
e
1
CN2
S-Video
12
CN3
4
Bluetooth Cable CNTR
2
CN4
LCM Cable CNTR
13
CN3
2
Speaker Cable CNTR
3
CN7
3G Card CNTR
14
Jack
5
Headphone Jack
4
CN8
Hot Keyboard CNTR
15
Jack
3
Line-In Jack
5
CN1
2
Keyboard FFC CNTR
16
Jack
4
MIC Jack
6
CN1
3
Fine Track FFC
CNTR
17
CN2
7
5 in 1 Card Reader
Socket
7
CN1
8
MIC Cable CNTR
18
CN3
3
Speaker CAble CNTR
8
CN2
0
TouchPad FFC CNTR
19
CN2
4
PCMCIA Socket
Description
5
Ite
m
Nam
e
Description
Ite
m
Nam
e
9
CN1
9
SmartCard CAble
CNTR
20
CN2
6
PCMCIA Socket
10
CN2
8
MDC CNTR
21
CN2
2
USB
11
CN2
9
IO Board CNTR
22
D47
IR Receiver
Description
Bottom View
6
Item
Name
Description
Ite
m
Name
Description
1
Jack50
0
DC In Jack
11
U512
South Bridge
2
CN500
Serial Port
12
CN51
5
W/LAN Card CNTR
3
CN501
Fan Cable CNTR
13
CN51
1
ODD CNTR
4
CN508
1394
14
CN51
0
HDD CNTR
Chapter 1
Item
Name
Description
5
Jack50
1
Ethernet jack and RJ11
Jack
6
U507
7
Ite
m
Name
Description
15
CN50
7
Second Battery CNTR
North Bridge
16
CN50
6
RTC Battery CNTR
U505
CPU Socket
17
CN50
5
MDC Cable CNTR
8
CN509
MDC Cable CNTR
18
CN50
4
MainBoard and IO Board
CNTR
9
CN512
DIMM Socket
19
CN50
3
Docking CNTR
10
CN513
DIMM Socket
20
CN50
2
Battery CNTR
Chapter 1
7
Your Acer Notebook tour
After knowing your computer features, let us show you around your new TravelMate 6492 computer.
Front View
#
8
Item
Description
1
Acer Crystal Eye
Web camera for video communication (for selected
models).
2
Display screen
Also called Liquid-Crystal Display (LCD), displays
computer output.
3
Acer Fine Touch
Keyboard
For entering data into your computer.
4
Acer Fine Track
Touch-sensitive pointing device which functions like a
computer mouse when used together with the click
buttons.
5
Acer Bio-Protection
fingerprint reader
The center button serves as Acer Bio-Protection
fingerprint reader supporting Acer FingerNav 4-way
control function. (for selected models).
6
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
7
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the
status of the computer's functions and components.
Chapter 1
8
Click buttons (left, center
and right)
The left and right buttons function like the left and right
mouse buttons; the center button serves as a 4-way
scroll button.
9
Palmrest
Comfortable support area for your hands when you use
the computer.
10
FineTrack buttons (left
and right)
Function like the left and right mouse buttons when
used together with the center-keyboard FineTrack.
11
Power button
Turns the computer on and off.
12
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the
status of the computer's functions and components.
13
## Easy-launch
Item
Description
buttons
Buttons for launching frequently used programs.
Item
Description
14
Microphone
Internal microphone for sound recording.
Closed Front View
"Easy-launch buttons" on page 18
#
Icon
1
#
Icon
Speakers
Description
Description
Left and right speakers deliver stereo
audio output.
2
Power indicator
Indicates the computer’s power status.
3
Battery indicator
Indicates the computer’s battery
status.
4
#
#
Chapter 1
Item
Item
Icon
Icon
Infrared port/CIR
Interfaces with infrared devices (e.g,
receiver
infrared printer and IR-aware
Item
Description
Item
Description
computer)/Receives signals from a
remote control.
5
5-in-1 card reader
Accepts Secure Digital (SD),
MultiMediaCard (MMC), Memory Stick
(MS), Memory Stick PRO (MS PRO),
Note: xD-Picture Card (xD).
6
Line-in jack
Accepts audio line-in devices (e.g.,
audio CD player, stereo walkman).
7
Microphone-in jack
Accepts input from external
microphones.
8
Headphones/
speaker/line-out
jack with S/PDIF
support
Connects to audio line-out devices
(e.g., speakers, headphones).
9
Bluetooth®
communication
button/indicator
Enables/disables the Bluetooth®
function. Indicates the status of
Bluetooth communication.
9
10
Wireless
communication
button/indicator
Enables/disables the wireless
function. Indicates the status of
wireless LAN communication.
11
Latch
Locks and released the lid.
Left View
#
10
Icon
Item
Description
1
S-video/TV-out
(NTSC/PAL) port
Connects to a television or display
device with S-video input.
2
Ventilation slots
Enable the computer to stay cool,
even after prolonged use.
3
4-pin IEEE 1394
port
Connects to IEEE 1394 devices.
4
Modem (RJ-11) port Connects to a phone line.
5
Ethernet (RJ-45)
Connects to an Ethernet 10/100/1000based network (for selected models).
6
USB 2.0 port
Connects to USB 2.0 devices (e.g.,
USB mouse, USB camera).
7
SmartCard slot
Accepts the TravelMate SmartCard
8
PC Card slot
Accepts one Type II PC Card.
9
PC Card slot eject
button
Ejects the PC Card from the slot.
Chapter 1
Right View
#
Item
Description
1
Icon
USB 2.0 port
Connect to USB 2.0 devices (e.g.,
USB mouse, USB camera).
2
Acer MediaBay
optical drive
Internal optical drive; accepts CDs or
DVDs (slot-load or tray-load
depending on model).
3
Optical disk access
indicator
Lights up when the optical drive is
active.
4
Optical drive eject
button
Ejects the optical disk from the drive.
5
Emergency eject
hole
Ejects the optical drive tray when the
computer is turned off.
6
Serial port
Connects to a serial device.
Rear view
#
Chapter 1
Item
Description
1
Icon
USB 2.0 port
Connect to USB 2.0 devices (e.g.,
USB mouse, USB camera).
2
DC-IN jack
Connects to an AC adapter.
3
External display
(VGA) port
Connects to a display device (e.g.,
external monitor, LCD projector).
4
Kensington lock
slot
Connects to a Kensingtoncompatible computer security lock.
11
Base view
#
12
Item
Description
1
Battery bay
Houses the computer’s battery pack.
2
Battery lock
Locks the battery in position.
3
ezDock II/II+ connector
Connects to the Acer ezDock II/II+.
4
Acer MediaBay release
latch
Lock or unlock the Acer MediaBay
device.
5
Hard disk bay
Houses the computer’s hard disk
(secured with screws)
6
Memory compartment
Houses the computer’s main memory.
7
Acer DASP
Disk Anti-Shock Protection.
8
Battery latch
Release the battery pack.
Chapter 1
Indicators
The computer has several easy-to-read status indicators.
The front panel indicators are visible even when the computer cover is closed up.
Icon
Function
Icon
Function
Description
Description
Cap lock
Lights when Cap Lock is activated
Num lock
Lights when Num Lock is activated.
HDD
Indicates when the hard disc or
optical drive is active.
Wireless LAN
Indicates the status of wireless LAN
communication.
Bluetooth
Indicates the status of Bluetooth
communication.
Battery
Lights up when the battery is being
charged.
Power
Lights up when the computer is on.
Note: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Chapter 1
13
Easy-Launch Buttons
Located above the keyboard are four buttons. These buttons are called easy-launch buttons. They are: mail Web
browser, Empowering Key “
“and one user-programmable button.
Press “
“ to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email and
Internet programs, but can be reset by users. To set the Web browser, mail and programmable buttons, run the
Acer Launch Manager.
Launch key
Default application
Acer Empowering Technology (userprogrammable)
P
User-programmable
Web browser
Internet browser (user-programmable)
Mail
Email application (user-programmable)
Touchpad Basics
The following teaches you how to use the touchpad:
14
•
Move your finger across the touchpad (2) to move the cursor.
•
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad
Chapter 1
is the same as clicking the left button.
•
Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your
cursor pressing on the right scroll bar of Windows applications.
Function
Left Button
(1)
Right Button
(4)
Main
touchpad (2)
Execute
Click twice
quickly
Tap twice (at
the same
speed as
doubleclicking the
mouse
button)
Select
Click once
Tap once
Drag
Click and
hold, then use
finger on the
touchpad to
drag the
cursor.
Tap twice (at
the same
speed as
doubleclicking a
mouse
button); rest
your finger on
the touchpad
on the second
tap and drag
the cursor.
Access
context menu
Scroll
Center button (3)
Click once
Click and hold to move
up/down/left/right.
Note: When using the touchpad, keep it - and your infers - dry and clean. The touchpad is sensitive to finger
movements; hence, the lighter the touch, the better the response. Tapping too hard will not increase the
touchpad’s responsiveness.
Chapter 1
15
Using the Keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve
function keys.
Lock Keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock Key
Caps Lock
Description
When Caps Lock is on, all alphabetic characters
typed are in uppercase.
Num lock
When Num Lock is on, the embedded keypad is
<Fn>+<F11> in numeric mode. The keys function as a
calculator (complete with the arithmetic
operators +, -, *, and /). Use this mode when
you need to do a lot of numeric data entry. A
better solution would be to connect an external
keypad.
Scroll lock When Scroll Lock is on, the screen moves one
<Fn>+<F12> line up or down when you press the up or down
arrow keys respectively. Scroll Lock does not
work with some applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are
not printed on the keys.
16
Desired Access
Num Lock On
Num Lock Off
Number keys on
embedded keypad
Type numbers in a
normal manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using
cursor-control keys.
Hold <Fn> while using
cursor-control keys.
Main keyboard keys
Hold <Fn> while typing
letters on embedded
keypad.
Type the letters in a
normal manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Icon
Windows
key
Description
Pressed alone, this key has the same effect as
clicking on the Windows Start button; it launches
the Start menu. It can also be used with other
keys to provide a variety of function:
+ <Tab> Activates next taskbar button.
+ <E> Opens the My Computer window
+ <F1> Opens Help and Support.
+ <F> Opens the Find: All Files dialog box.
+ <R> Opens the Run dialog box.
+ M Minimizes all windows.
<Shift>+
+ <M> Undoes the minimize all
windows action.
This key has the same effect as clicking the right
mouse button; it opens the application’s context
menu.
Applicat
ion key
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hot Key
Function
Description
<Fn>+<F1>
Hot key help
Displays help on hot keys.
<Fn>+<F2>
Acer eSetting
Launches the Acer eSettings in Acer eManager.
<Fn>+<F3>
Acer
Launches the Acer ePowerManagement in Acer
ePowerManagement Empowering Technology. See “Acer
Empowering Technology” on page 19.
<Fn>+<F4>
Sleep
Chapter 1
Icon
Puts the computer in Sleep mode.
17
Hot Key
Icon
Function
Description
<Fn>+<F5>
Display toggle
Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn>+<F6>
Screen blank
Turns the display screen backlight off to save
power. Press any key to return.
<Fn>+<F7>
Touchpad toggle
Turns the internal touchpad on and off.
<Fn>+<F8>
Speaker toggle
Turns the speakers on and off.
<Fn>+<w>
Volume up
Increases the speaker volume.
<Fn>+<y>
Volume down
Decreases the speaker volume.
<Fn>+<-x>
Brightness up
Increases the screen brightness.
<Fn>+<z>
Brightness down
Decreases the screen brightness
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard. To
type:
The Euro symbol
1. Open a text editor or word processor.
2. Either directly press the < > symbol at the bottom-right of the keyboard, or hold <Alt Gr> and then press
the<5> symbol at the upper-center of the keyboard.
Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1. Open a text editor or word processor.
2. Either directly press the < > key at the bottom-right of the keyboard, or hold <Shift> and then press the <4>
key at the upper-center of the keyboard.
Note: This function varies by the operating system version.
18
Chapter 1
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and manage
your new Acer notebook. It features the following handy utilities:
q
q
q
q
q
q
q
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
Acer eLock Management limits access to external storage media.
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry settings.
Acer eRecovery Management backs up/recovers data flexibly, reliably and completely.
Acer eSettings Management accesses system information and adjusts settings easily.
Acer ePower Management extends battery power via versatile usage profiles.
Acer ePresentation Management connects to a projector and adjusts display settings conveniently.
For more information, press the <
> key to launch the Empowering Technology menu, then click on the
appropriate utility and select the Help function.
Acer eDataSecurity Management
Acer eDataSecurity Management is handy file encryption utility that protects your files from being accessed by
unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and easy
data encryption/decryption and also supports on-the-fly file encryption for MSN Messenger and Microsoft Outlook.
Chapter 1
19
There are two passwords that can be used to encrypt/decrypt a file; the supervisor password and the file-specific
password. The supervisor password is a “master” password that can decrypt any file on your system; the filespecific password will be used to encrypt files by default, or you can choose to enter your own file-specific
password when encrypting a file.
Note: The password used encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt your encrypted file! Be sure to safeguard all related passwords!
20
Chapter 1
Acer eLock Management
Acer eLock Management is a security utility that allows you to lock up your removable data, optical and floppy
drives to ensure that data can’t be stolen while your notebook is unattended.
q
q
q
Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
Optical drive devices - includes any kind of CD-ROM or DVD-ROM drives.
Floppy disk drives - 3.5-inch disks only.
To activate Acer eLock Management, a password must be set first. Once set, you may apply lock to any of the
three kinds of devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked after
rebooting, until unlocked.
If you do not set a password, Acer eLock Management will reset back to the initial status with all locks removed.
Note: If you lose your password, there is no method to reset it except by reformatting your notebook or taking
your notebook to an Acer Customer Service Center. Be sure to remember or write down your password.
Chapter 1
21
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer notebook.
It provides you with the following options to enhance overall system performance:
q
q
q
22
Memory optimization - releases unused memory and check usage.
Disk optimization - removes unneeded items and files.
Speed optimization - improves the usability and performance of your Windows XP system.
Chapter 1
Acer eRecovery Management
Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by the
manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on your system’s
HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides you with:
q
Password protection.
q
Recovery of applications and drivers.
q
Image/data backup:
•
Back up to HDD (set recovery point).
•
Back up to CD/DVD.
Image/data recovery tools:
•
Recover from a hidden partition (factory defaults).
•
Recover from the HDD (most recent user-defined recovery point).
•
Recover from CD/DVD.
q
Chapter 1
23
Note: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To ensure the
best results when recovering your system using a CD or Acer eRecovery Management, detach all peripherals
(except the external Acer ODD, if your computer has one), including your Acer ezDock.
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications and to monitor the system health
status. Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so
your computer runs faster, smoother and better.
Acer eSettings Management also:
q
Provides a simple graphical user interface for navigating through the program effortlessly.
q
Displays general system status and advanced monitoring for power users.
q
Logs when a hardware component has been removed or replaced.
q
Permits you to migrate personal settings.
q
Keeps a history log of all alerts that were previously issued.
24
Chapter 1
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface, or double-click the Acer ePower Management icon in
the task tray.
Acer Mode
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other settings, or
click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, Memory Card, Audio, and
Wired LAN.
DC Mode
To suit your usage, there are four pre-defined profiles - Entertainment, Presentation, Word Processing, and
Maximum Battery. Or, you can define up to three of your own profiles.
Create new power scheme
1. Assign a name for the new scheme.
2. Choose existing scheme to use as a template.
3. Select whether used for mains (AC) or battery mode.
4. Choose which power options best fit your needs, then click OK.
5. The new profile will appear on the main screen.
Battery status
For real-time battery life estimates based on current usage, refer to the panel on the lower left-hand side of the
window.
Chapter 1
25
You can also click “Advanced Settings” to:
q
Set alarms.
q
Re-load factory defaults.
q
Select what actions will be taken when the cover is closed, and set passwords for accessing the system
after Hibernation or Standby.
q
View information about Acer ePower Management.
26
Chapter 1
Acer ePresentation Management
Acer ePresentation Management lets you select from two of the most common projector resolutions: XGA and
SVGA.
Chapter 1
27
Acer OrbiCam
The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The
camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the
back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that you can
transmit the best video quality over an instant Messenger service.
Getting to know your Acer OrbiCam
1
#
23
Item
No.
#
1
Item
Item
Lens
2
Power indicator
3
Rubber grip (selected models only)
Rotating the Acer Orbicam
The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the illustrations
below:
For your convenience, the camera snaps 45 degrees to match the position of your face in front or at the back of
the LCD panel.
Note: Do not rotate the camera clockwise to prevent damage to the device.
Launching the Acer OrbiCam
To launch the Acer OrbiCam, double click on the Acer OrbiCam icon on the screen.
OR
Click Start > All programs > Acer > Acer OrbiCam. The Acer OrbiCam capture windows window appears.
28
Chapter 1
Changing the Acer OrbiCam settings
Resolution
To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window,
then select the desired resolution.
Options
Click Options to display Options
the Window, Preview,Window,
and Folder
tabs. UseFolder
the options to change the capture window
Preview
size, preview settings, and the folder for captured photos or videos.
Camera Settings
•
Basic settings: Click the Camera Settings icon on the bottom right corner of the capture display, then
select Camera Settings from the pop-up menu. You can adjust the Video, Audio, and Zoom/Face tracking
options from this window.
Chapter 1
29
Video, Audio
Video, Audio
•
Camera Settings
Camera Settings
Zoom/Face
tracking
Zoom/Face tracking
Capture settings: From the Camera Settings window, click the Driver Settings button. The Properties
Driver Settings
window willProperties
appear.
Driver Settings
Properties
Device Settings
Device Settings
•
Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness, etc.
•
Advanced Settings
Advanced Advanced
Settings
allows
you to achieve gain control, implement image mirror, select image
Settings
enhancements and anti-flicker settings, and turn on/off the camera indicator.
•
Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature on or off.
Zoom/Face Track Settings
Zoom/Face Track Settings
Capturing photos or videos
To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a Picture
or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player automatically
launches to display or play a preview of the photo/video clip.
Note: By default, all photos and videos are saved in the My Pictures and My Videos folder.
Using the Acer OrbiCam as webcam
The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application. To
use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can now
broadcast from your location to an IM partner anywhere in the world.
Enabling the Acer VisageON
The Acer VisageON technology comes with two features: Face tracking and Video effects (selected models only).
The Face Tracking feature tracks your head movement and automatically centers your face in the capture window.
The video effects feature allows you to select and apply an effect to your video transmissions.
Note: The face tracking feature is not capable of centering your face beyond the capture window frame.
Minimal head movements are tracked more efficiently.
To enable the Acer VisageON:
1. Right click on this icon, then select VisageON from the pop-up menu.
30
Chapter 1
VisageON
VisageON
VisageON
The VisageON window appears as below:
2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings
and options in the right section.
Using the face tracking feature
To use the face tracking feature:
Single User
Multiple
Users
Single
Userfrom
1. Click the left icon down arrow button, then select Single User or Multiple
Users
the pop-up menu. For
Single
User
Multiple
Users
Users
multiple users, the face
tracking feature automatically centers all the users’ face in the capture window,
otherwise the utility centers the face of the user closest to the camera.
2. Click the right icon to zoom in/out or reset the current view.
VisageON
3. Click VisageON to display a menu that allows to change the configuration of the camera, face tracking and
video effects settings.
Chapter 1
31
VisageON
VisageON
video
effects
Using video effectsUsing
(selected
models
only)
Using video effects
The Video Settings section
allows
you to select an avatar or accessory video effect from the list. To select an
Video
Settings
Video Settings
effect:
1. Click the encircled icon to display the available video effects. The Video Effect Selection
Video window appears as
Video
Effect Selection
below:
Effect Selection
2. Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window.
Note: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow screen
instructions in the VisageON to continue.
Note: You may use video effects when using the camera for IM chat/video sessions or call conferences.
32
Chapter 1
Note:
Using the System Utilities
Note: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
Note: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure
thatControl
the second
monitor
is connected, then select
Start
Panel
Display
Start, Control Panel, DisplayNote:
and click on Settings. Select the secondary monitor (2) icon in the display box and
Settings
(2)
then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new
Extend
my
windows
desktop
onto this monitor
settings and click OK to complete the process.
Apply
OK
Settings
Apply
Start Control Panel Display
(2)
Extend my windows desktop onto this monitor
OK
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on
the same screen. To access
function,
please go to Start>AllAcer
Programs
and click on Acer GridVista. You may
StartthisAll
Programs
GridVista
Startsettings
All Programs
choose any one of the four display
indicated below: Acer GridVista
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display compatible,
allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is simple to set up:
1.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
Chapter 1
33
Note: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.Note:
Note:
Launch Manager
Launch Manager allows you"Easy-launch
to set the four buttons"
easy-launch
above the keyboard. You can access the
onbuttons
page located
24
Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
Start24
All Programs
"Easy-launch buttons" on page
Launch Manager
Start All Programs
Launch Manager
34
Chapter 1
Hardware Specifications and Configurations
Core System
Item
Description
Specifications
1
CPU
Mobile Intel Core 2 Duo Mobile Processor
Package: Micro-FCPBA 478-pin
Features:
Chapter 1
•
Dual core processor for mobile with enhanced performance
•
Support Intel Architecture with Intel Wide Dynamic Execution
•
Support L1 Cache to Cache (C2C) transfer
•
On-die, primary 32-KB instruction cache and 32-KB write-back data
cache in each core
•
On-die, up to 4-MB second level shared cache with Advanced Transfer
Cache Architecture
•
Streaming SIMD Extensions (SSE2), Streaming SIMD Extensions (SSE3)
and Core New Instruction (CNI)
•
533, 667, and 800 MHz Source-Synchronous Frond Side Bus (FSB)
•
Advanced power management features including Enhanced Intel
Speedstep Technology and Dynamic FSB frequency switching
•
Digital Thermal Sensor (DTS)
•
Micro-FCPGA and Micro-FCBGA packaging technology
•
Execute Disable Bit support for enhanced security
•
Intel 64 Technology (Intel 64T)
•
Support Enhanced Intel Virtualization Technology
•
Intel Dynamic Acceleration Technology and Enhanced Multi Threaded
Thermal Management (EMTTM)
•
Supports PSI2 functionality
35
Core System
Item
Description
Specifications
2
North
Bridge
Intel 965GM (North Bridge)
Package: FCBGA 1299 balls
Features:
36
•
Source synchronous double-pumped (2x) address
•
Source synchronous quad-pumped (4x) data
•
Support for Dynamic FSB Frequency Switching
•
12-deep in-order queue to pipeline FSB commands
•
AGTL+ bus driver with integrated AGTL termination resistors
•
Supports Dual Channel DDR2 SDRAM
•
One-SO-DIMM connector (or memory module) per channel
•
Maximum memory supported: 4GB
•
Intel Flex Memory Technology support
•
64-bit wide per channel
•
Support for DDR2 at 667 MHz and 533 MHz
•
256-Mb, 512-Mb, 1-Gb, and 2-Gb memory technologies supported
•
Support for x8 and x16 devices
•
Support for DDR2 On-Die Termination (ODT)
•
No support for ECC
•
Integrated Intel ActiveManagement Technology (Intel AMT)
•
Intel AMT 2.5 with both wired and wireless LAN support
•
Internal Graphics (GM965 only)
•
Mobile Intel Graphic Media Accelerator X3000 (Mobile Intel GMA
X3000)
•
Support TV-out, LVDS, CRT and SVDO
•
Dynamic Video Memory Technology (DVMT 4.0)
•
Intel Smart 2D Display Technology (Intel S2DDT)
•
High performance MPEG-2 decoding
•
WMV9 (VC-1) and H.264 (AVC) support
•
Hardware acceleration for VLD/iDCT
•
Microsoft DirectX 9 and DirectX 10 support
•
Integrated 300-MHz RAMDAC for analog CRT
•
25-112 MHz single/dual channel LVDS
Chapter 1
Core System
Item
Description
Specifications
3
South
Bridge
Intel ICH8ME (South Bridge)
Package: mBGA 676 balls
Features:
4
System
clock
•
PCI Express Base Specification, Rev 1.1 support
•
ACPI Power Management Logic Support
•
Enhanced DMA controller, interrupt controller, and timer function
•
Integrated Serial ATA host controllers with independent DMA operation
on three ports and AHCI support
•
Integrated IDE controller supports Ultra ATA100/66/33
•
USB host interface with support for ten USB ports; five UHCI host
controllers; two EHCI high-speed USB 2.0 host controllers
•
Integrated 10/100/1000 GbE MAC with circuit breaker
•
System Management Bus (SMBus) Specification, ver 2.0 with additional
support for I2C devices
•
Supports Intel High Definition Audio (Intel HD Audio)
•
Support Intel Matrix Storage Technology
•
Support Intel AMT
•
Low Pin Count (LPC) interface
•
Firmware Hub (FWH) interface support
•
Serial Peripheral Interface (SPI) support
•
6 PCIe ports
System clock chip: ICS ICS9LPRS365 or pin compatible device
Package: 64 pin TSSOP
Crystal and Oscillator:
•
Clock Synthesizer: 166/200Mhz for CPU, GMCH
•
100MHz clock buffer for SRC and PCI-E device, SATA
•
33Mhz PCI clock for PC device,SIO,LPC
•
48MHZ — USB controller base clock ICH8
•
96MHZ — GM965 dot clock
32.768Khz — ICH internal RTC and KBC base clock
Power: 3.3V, 1.25V
Features:
•
•
5
Thermal IC
Support spread spectrum function, for reducing EMI. Support SM bus
interface
Analog Device ADM1032ARM
Package: MSOP 8-pin
Features:
•
Thermal sensor control
Interface: I2C bus, address: (9Ch)
Chapter 1
37
Core System
Item
Description
Specifications
6
System
memory
Package: DDR2 SDRAM in 84-ball FBGA
Supply voltage: 1.8V±0.1V
Speed: 667MHz / 533MHz (CL=4 or 5)
Refresh:
•
Auto & self refresh capability
•
7.8µs(max),Average periodic refresh interval
Features:
7
BIOS ROM
•
Data is read or written on both clock edges
•
Address and control signals are fully synchronous to positive clock edge
WX25X80VSSIG
ROM type: Organized as 8M×1
Package: 8 PIN SOIC (8.1mm×5.38mm)
Block-Erase: uniform 64 KByte blocks
Supply current:
•
Active current =5 mA (Typical)
•
Standby current=1 uA (Typical)
Superior reliability:
•
Endurance: 100,000 cycles (Typical)
•
Greater than 20 years data retention
DISPLAY SUBSYSTEM
The 965GM contains a dual-channel 24-bit LVDS interface. Notice that for designs implementing only a single
LVDS channel, the LOWER channel of the interface should be used.
•
Integrated dual 24-bit LVDS interface.
•
595 Mbps/channel with 85 MHz pixel clock rate.
•
FPDI-2 compliant; compatible with receivers from National Semiconductor, Texas Instruments, and THine.
•
OpenLDI compliant excluding DC balancing.
•
Programmable internal spread spectrum controller for the LVDS signals.
•
LVDS eye pattern to improve testability of LVDS module
LCD Power On Sequence
LCD timing must follow up below specification to meet the minimum requirements.
•
ENAVDD(LCDVCC)´ SHFCLK(DATA)--´BLON (power on sequence)
•
BLON´SHFCLK(DATA)--´ENAVDD(LCDVCC) (power off sequence)
Note A: This timing depends on LCD specification
AUDIO SUBSYSTEM
Audio Codec
Audio chip: Realtek ALC268
Package: 48-pin LQFP 'Green' package
Features:
38
•
All ADCs support 44.1K/48K/96K/192kHz sample rate
•
All ADCs support 44.1K/48K/96kHz sample rate
Chapter 1
•
Support external PCBEEP input and built-in digital BEEP generator
•
Power support: Digital:3.3V; Analog:3.3V~5.0V
Speaker Amplifier
Amplifier: GMT G1432
Package: Thin QFN 24-pin (4.8mm×4.8mm×1mm)
Features:
•
2W into 4O(1% THD+N)
•
2.6W into 4O(10% THD+N)
•
Power supply ripple rejection 65dB PSRR
•
Supply current in Mute mode (Typ:7mA)
•
Low-Power Shutdown Mode: Typ 2 µA
•
Mute and shutdown function
Audio Port
Internal:
•
Two speakers
•
Microphone
External:
•
Microphone Jack
•
Line-In Jack
•
H-P Jack
PCMCIA SUBSYSTEM
PCMCIA controller for Socket
Part name: O2_OZ601TN
Package: 128pin LQFP
Compliant: PCI local bus specification Rev.2.3
Features:
•
Supports SPKROUT CAUDIO and RIOUT#
•
Supports standardized zoomed register model
•
Support serialized IRQ interrupt and PCI interrupts
•
Support PCI PME# from D3 cold
Power: 3.3V operation with I/O 5V tolerance
PC card power controller chip for CB714
Part name: Ti TPS2210A
Package: TSSOP 24-pin
Features:
•
1A output current for VCCOUT
•
100mA output current for VPPOUT
Power: Vcc=5V, 3.3V
I/O SUBSYSTEM
Keyboard
Dimension: 310 x 115 x 5.5 mm
Weight: 120 Gram (max)
Chapter 1
39
Type: 84/88 key full size ergo keyboard
KEY number: TBD
Lift: TBD
Pointing Device
TravelMate 6492 uses touch pad as the pointing device. The touch pad module is connected to TP-Board through
the FFC connector. The touchpad support 6 buttons (Left/Right button and 4-way button Function.
Touch pad: Synaptics TM61PUF1R544
Physical size: 40x67 mm
Weight: TBD
Active area: 38 x65 mm
Mini Card 802.11 a/g Module
Form factor: 59.6mm* 44.6mm* 3.3mm with 124 pins connector
Voltage Supply: 3.3Volts
Features:
•
Support wireless data encryption with 64/128/152-bit WEP standard for security
•
Allows auto fallback data rate for optimized reliability, throughput and transmission range
•
Support Ad-hoc mode (peer-peer) and Infrastructure mode (client-sever) communication
•
Dual diversity antenna connectors supported for the multi-path environment
I/O Port
I/O Support on the System
40
•
CRT port --- Support CRT monitor.
•
3 * USB 2.0 ports
•
MIC-In
•
Line-In
•
RJ11/RJ45
•
DC Jack
•
1394 port
•
Cardbus
•
5 in 1 card reader
•
1* Serial port
•
EZ II / II+ connector
Chapter 1
SYSTEM POWER PLANES
Power Plane
Active
State
Control
signal
Device
VCCRTC
Always
-
SB460, PC97551
VL
Always
-
15V
Always
-
MOS Gate
5VPCU
Always
-
TPS51120
3VPCU
Always
-
NS PC97551, TPS51120
1.8V_S5
S0-S5
S5_ON
G913C, SB460
3V_S5
S0-S5
S5_ON
AO6402, RTL8100CL, MODEM
5V_S5
S0-S5
SUSON
USB
3VSUS
S0-S3
SUSON
SB460, MINI-PCI,AO6402
+2.5V
S0-S1
MAINON
G913-C, Athlon64
+1.8V
S0-S1
MAINON
AO6402, RS485, SB460, Athlon64
+1.5V
S0-S1
MAINON
G966, MINIPCI
+3V
S0-S1
MAINON
CLK Gen., AO6402, Athlon64, SB485, DDR2 SO-DIMM, LCD,
PCMCIA, MINI-PCI, CODEC, PC97551
+5V
S0-S1
MAINON
SB460, CRT, LCD, PCMCIA, MINI-PCI, AUDIO, HDD, ODD,
FAN, TP,
CPU_VCCA
S0-S1
MAINON
Athlon64 CPU, RS485
VCC_CORE
S0-S1
VRON
Athlon64 CPU
+VTT
S0-S1
VRON
Athlon64 CPU, TPS51116
1. VL/5VPCU/3VPCU: These power planes will always be turned on unless the AC adapter and battery pack is
removed from the system. 5VPCU is the power source of +5V and 5V_S5 and 3VPCU is the power source of
+3V, 3VSUS and 3V_S5.
2. VCCRTC: This power plane will always be turned on even when the AC adapter and battery pack is removed
form the system. This battery backed up power is used by the RTC module inside the SB460.
3. 1.8V_S5/3V_S5/5V_S5: These power plane are used by SB460 Suspend/Resume power plane.
4. 3VSUS: These power planes will be stay on even when the system in the Suspend state
5. +1.5V/+1.8V/+3V/+5V: These power plane will be switch off when the system goes into the suspend mode.
6. 3V_S5/+5V_S5: This power plane will be stay on in S0 - S4 state and is used by devices that support D3 cold
wake up.
Input Characteristics
Functions
Description
Input voltage
90V AC ~ 264V AC
Input frequency range
47 ~ 63 Hz
Maximum input AC current
3.42A
Inrush current
50A@115VAC100A@230VAC
Efficiency
85% min. @110VAC / 65W load85% min. @240VAC / 65W load
Output characteristics
Output Voltage
Load range (Min)
Load range (max)
Regulation
Ripple & Noise
+19v
0A
3.42A
+-5%
400mVp-p
Indicator: power LED (green)
Chapter 1
41
Keyboard controller
Part name: iTE IT8152
Package: QFP 128-pin
Features:
•
8032 Embedded Controller
•
LPC Bus Interface
•
PS/2 interface for touchpad
•
Flash Interface
•
SM Bus Controller
•
System Wake Up Control / Ec Wake Up Control
•
Interrupt Controller
•
ACPI PowerManagement Channel
•
PWM With Smart Auto Fan Control
Supply current: Standby With Sleep Mode Current: 100uA
Speaker
Model: YYD2112G
Impedance: 4 Ohm ± 15% on 2100Hz
Rated input: 2 W
Lowest resonance frequency: 850Hz ± 20%
Output sound pressure level: 78db ± 3 dB at 1.0W
Dimension: TBD
Weight: TBD
SYSTEM LED Indicator
System LED Indicator
The following information provide the LED icon for TravelMate 6492 system.
•
Battery LED
•
Power/Suspend LED
•
Wireless LED
•
Bluetooth LED
POWER SPECIFICATION
System Power States
ZR3 supports 6 different power states in the system. The SB460 automatically controls the signals required to
transition the system between the various power states and also informs the PC97551 to control the power planes
as required.
The following table describes the different power states switching matrix:
Current State
Initial
Next State
Initial
ON
Suspend
Hibernate
Soft Off
(2)
(3)
(4)
(5)
(1)
ON(S0)
42
Standby
Standby(S1)
(6)
Suspend(S3)
(7)
Chapter 1
Hibernate(S4)
(8)
Soft Off(S5)
(9)
Mechanical off is a condition where all power except the RTC battery has been removed from the system.
1. Initial to On state: When the AC adapter or Battery pack has been plugged into the system, the PC97551 will
be reset and initial all output pins then the system goes into Initial state and waiting for power on event. If the
power button is pressed then the system will go into the ON state.
2. ON to Standby state: The system will go into the Standby state when 963L receives the POS command.
3. ON to Suspend state: The system will go into Suspend state when SB460 receives the S2R command.
4. ON to Hibernate state: The system will go into Hibernate state when SB460 receives the S2D command.
5. ON to Soft Off state: The system will go into Soft Off state when SB460 receives the Soft off command.
6. Standby to ON state: The system will go into ON state when the system receives any wake up events, for
example, power button, Lid switch.
7. Suspend to ON state: The system will go into ON state when the power button is pressed.
8. Hibernate to ON state: The system will go into ON state when the power button is pressed.
9. Soft Off to ON state: The system will go into ON state when the power button is pressed.
Power Control Pin Description
The following table is NS PC97551 power control pin description:
State
Output Pin
S5_ON
3VAUXEN
SUSON
MAINON
VRON
Initial
0
0
0
0
0
ON(S0)
1
1
1
1
1
Standby(S1)
1
1
1
1
1
Suspend(S3)
1
1
1
0
0
Hibernate(S4)
1
1
0
0
0
Soft Off(S5)
1
0
0
0
0
Battery and Charger
Current Amplifier: MAX8724
Charge PWM Control: IMD2AT108
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Min Input Range
VA
18
19
20
V
Input Low Voltage
M/A-, D/C-, BL/C-, REFON
0.8
V
Input high Voltage
M/A-, D/C-, BL/C-, REFON
2.5
5.5
V
Charge Voltage
CV-SET =0V
15.93
16.09
16.25
V
Charge Voltage
CV-SET =5V
16.95
17.11
17.27
V
Charge Current
CC-SET =0.5V (for Li -ion)
0.1
0.25
0.4
A
Charge Current
CC-SET =5V (for Li-ion)
3.73
3.93
4.13
A
Charge PWM Frequency
Efficiency
VA=19V Output 12V/1.7A
200
KHz
91
%
3-13.1. DC to DC Converter
TI TPS51120 PWM chip: 5V & 3.3V &15V
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
5V
Current 0-3A
4.8
5.0
5.2
V
3.3V
Current 0-3A
3.14
3.35
3.76
V
Chapter 1
43
TI TPS51120 PWM chip: 5V & 3.3V &15V
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
15V
Current 0-100mA
11.4
12
12.6
V
Output Current
5V
0
3
A
Output Current
3.3V
0
3
A
Output Current
15V
0
100
mA
Input Voltages
19V
8
20
V
Semtech G913-C PWM chip:2.5V
PARAMETER
CONDITIONS
MIN
Output Current
2.5V
Input HighVoltages
TYP
MAX
UNITS
0
7
A
1.8
25
V
Intersil MAX8774 PWM chip: CPU VCORE (0.8V ~ 1.55V for different frequency of CPU)
PARAMETER
CONDITIONS
MIN
VCC-CORE
Current 0-30A
0.8
TYP
MAX
UNITS
1.55
V
TI TPS51117 LDO chip: 1.2V
PARAMETER
CONDITIONS
MIN
MAX
UNITS
Output Current
1.25V
0
1.5
A
1.6
5.5
V
Input HighVoltages
TYP
Semtech G966 LDO chip: +1.2V_HT, 1.5V
MAX
UNITS
Output Current
PARAMETER
CONDITIONS
0
MIN
TYP
2
A
Input HighVoltages
1.6
5.5
V
TI TPS51116 LDO chip: 1.8V
PARAMETER
CONDITIONS
MIN
MAX
UNITS
Output Current
2.5V
0
1.5
A
2.2
5.5
V
Input HighVoltages
TYP
DC-AC inverter
ZR3 provides backlight adjustable DC-AC inverter. Dimension T.B.D mm
For 14" LCD TFT panel (LVDS Interface)
Parameter
Min
Typical
Max
Unit
Lamp voltage
1400
1600
1900
Vrms
Lamp frequency
50
55
60
KHz
Lamp current
5.6
6
6.4
mArms
AC adapter
Part name: TBD
Input characteristics: 90Watt
44
Chapter 1
Battery
Main battery:
Specification
LiIon
Parts name
3UR18650Y-2-QC-ZR1
Dimension (CELL)
202(L)x 67(W)x23.7(H)
Normal capacity
38000mA
Normal voltage
11.1V
Charge voltage
12.60V±0.09V
RTC battery:
Part name: J11EAGLE
Capacity: 14mAH
Voltage: 3.0V
Chapter 1
45
46
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output
System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you
encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting
when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted on
the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change boot
device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without entering
BIOS SETUP Utility.
Phoenix TrustedCore Setup Utility
Information Main Advanced Security Boot
Exit
CPU Type:
Genuine Intel ® CPU
CPU Speed:
XXXXGHz
Help Item
Menu Level
IDE0 Model Name:
Intel Raid0
IDE0 Serial Number:
TSST CorpCD
IDE1 Model Name:
MK3018GAP-(PM)
IDE1 Serial Number:
Y2554027T
ATAPI Model Name
Slimtype DVD-ROM LSD-081-(S
System BIOS Version
V1.0
VGA BIOS Version
ATI M9+XC V0.1
Serial Number
XXXXXXXXXX
Asset Tag Number
X
XXXXXXXXXX
Product Name
TravelMate XXXX
Manufacturer Name
Acer Inc.
UUID:
XXXXXXXXXX
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
Chapter 2
47
q
To choose a menu, use the cursor left/right keys (zx).
q
To choose a parameter, use the cursor up/down keys (wy).
q
To change the value of a parameter, press p or q.
q
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
q
Press ^ while you are in any of the menu options to go to the Exit menu.
q
In any menu, you can load default settings by pressing t. You can also press u to save any changes made
and exit the BIOS Setup Utility.
Note: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific
Help part of the screen. Read this carefully when making changes to parameter values. Please note that
system information is subject to different models.
Information
Note: The following system information is subject change between models and is for reference only.
Phoenix TrustedCore Setup Utility
Information
CPU Type:
Genuine Intel ® CPU
CPU Speed:
XXXXGHz
Help Item
Menu Level
IDE0 Model Name:
Intel Raid0
IDE0 Serial Number:
TSST CorpCD
IDE1 Model Name:
MK3018GAP-(PM)
IDE1 Serial Number:
Y2554027T
ATAPI Model Name
Slimtype DVD-ROM LSD-081-(S
System BIOS Version
V1.0
VGA BIOS Version
ATI M9+XC V0.1
Serial Number
XXXXXXXXXX
Asset Tag Number
X
XXXXXXXXXX
Product Name
TravelMate XXXX
Manufacturer Name
Acer Inc.
UUID:
XXXXXXXXXX
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
48
F5: Previous Values
F7: Optimized Defaults
Parameter
Description
CPU Type
This field shows the CPU type for the system
CPU Speed
This field shows the CPU speed for the system
IDE0 Model Name
This field shows the model name of HDD installed on primary IDE master
IDE0 Serial Number
This field displays the serial number of HDD installed on primary IDE master
Chapter 2
Parameter
Description
IDE1 Model Name
This field displays the model name of devices installed on secondary IDE
master. The hard disk drive or optical drive model name is automatically
detected by the system
IDE1 Serial Number
This field shows the serial number of devices installed on secondary IDE master
ATAPI Model Name
This field displays the ATAPI model name
System BIOS ver
Displays system BIOS version
VGA BIOS Ver
This field displays the VGA firmware version of the system
Serial Number
This field displays the serial number of this unit
Asset Tag Number
This field displays the asset tag number of the system
Product Name
This field shows product name of the system
Manufacturer Name
This field displays the manufacturer of this system
UUID Number
This will be visible only when an internal LAN device is present
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
Note: The screen below is for reference only. Actual values may differ.
Phoenix - Award WorkstationBIOS CMOS Setup Utility
Main
System Time
[09 : 00: 00]
System Date
[01 : 01: 2007]
Help Item
Menu Level
System Memory
640KB
Extended Memory
XXX
Video Memory
[8M]
Quiet Boot
[Enabled]
Network Boot
[Enabled]
F12 Boot Menu
[Disabled]
D2D Recovery
[Enabled]
X
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
Chapter 2
F5: Previous Values
F7: Optimized Defaults
49
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are
displayed with 24-hour format
Format: HH:MM:SS
(hour:minute:second)
System Date
Sets the system date
Format MM/DD/YYYY
(month/day/year)
System Memory
This field reports the memory size of the
system. Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system
(Extended Memory size=Total memory
size-1MB)
Video Memory
Shows the VGA memory size
Quiet Boot
Determines if Customer Logo will be
displayed or not; shows Summary Screen
is disabled or enabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled
Disabled: Customer Logo is not displayed,
and Summary Screen is enabled
Option: Enabled or Disabled
Network Boot
Enables or disables the system boot from
LAN (remote server)
Option: Enabled or Disabled
F12 Boot Menu
Enables or disables Boot Menu during
POST. Enabled: During quite boot, the
OEM POST screen displays Press
<F12>Change Boot Device
Disabled: During quite boot, the OEM
POST screen does not display Press
<F12>Change Boot Device
Option: Disabled or Enabled
Note: This Boot device change is applies to
next boot only.
D2D Recovery
Enables or disables D2D Recovery
function. The function allows the user to
create a hidden partition on hard disc drive
to store operation system and restore the
system to factory defaults
Option: Enabled or Disabled
Note: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
50
Chapter 2
Advanced
The Advanced screen displays advanced settings in BIOS.
Phoenix - Award WorkstationBIOS CMOS Setup Utility
Advanced
Serial Port
[Auto]
Infrared Port (FIR)
Help Item
[Auto]
Parallel Port
[Auto]
Mode
[ECP]
Menu Level
X
XASF Configuration
Minimum Watchdog Timeout
[ ]
BIOS Boot Timeout
[ ]
OS Boot Timeout
[ ]
Power-on wait Time
[ ]
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Serial port
Displays the setting of the serial port
Auto or Disabled
Infrared port
Displays the setting of the infrared port
Auto or Disabled
Parallel port
Displays the setting of the parallel port
Auto or Disabled
Mode
Displays the mode of the parallel port if
enabled
ECP/SPP/EPP
ASF Configuration
Access the ASF Submenu for the
following features:
Enter a figure in minutes
q
q
q
q
Minimum Watchdog Timeout
BIOS Boot Timeout
OS Boot Timeout
Power-on wait Time
Chapter 2
q
q
q
q
Minimum Watchdog Timeout —
BIOS Boot Timeout —
OS Boot Timeout —
Power-on wait Time —
51
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
Phoenix - Award WorkstationBIOS CMOS Setup Utility
Security
Supervisor Password Is
[Clear]
User Password Is
[Clear]
HDD Password Is
[Clear]
Set Supervisor Password
[Enter]
Help Item
Menu Level
Set User Password
[Enter]
Set HDD Password
[Enter]
Password on Boot
[Disabled]
X
Current TPM State
Change TPM State
[No Change]
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
52
F5: Previous Values
F7: Optimized Defaults
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Supervisor Password Is
Shows the setting for the Supervisor
password
Clear or Set
User Password Is
Shows the setting for the user password
Clear or Set
Clear or Set
HDD Password Is
Shows the setting for the HDD password
Set Supervisor Password
Press Enter to set the supervisor
password. When set, this password
protects the BIOS Setup Utility from
unauthorized access. The user can not
either enter the Setup menu nor change
the value of parameters
Set User Password
Press Enter to set the user password.
When user password is set, this
password protects the BIOS Setup Utility
from unauthorized access. The user can
enter Setup menu only and does not
have right to change the value of
parameters
Set HDD Password
Press Enter to set the HDD password.
When HDD password is set, this
password protects the Primary HDD
Password on Boot
Defines whether a password is required
or not while the events defined in this
group happen. The following sub-options
are all requires the Supervisor password
for changes and should be grayed out if
the user password was used to enter
setup
Disabled or Enabled
Current TPM State
Change TPM State
Note: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your dealer to
reset it.
Password Conventions
All the passwords must obey the following rules:
q
All the passwords can be set/cleared in BIOS Setup Security screen.
q
The password entry consists up to 8 alphanumeric characters. At least 1 character must be assigned in
this field.
The valid keys are listed in the table below:
Symbol Character
Symbol Name
A—Z
Alphabet A through Z (Not Case
Sensitive)
0—9
Numeric Characters
-
Dash
Chapter 2
53
Symbol Character
Symbol Name
=
Equals Sign
[
Left Bracket
]
Right Bracket
.
Period
,
Comma
;
Semi-colon
/
Slash
\
Back-slash
q
q
q
The maximum cycles to retry password is limited to 3.
User cannot change/remove password during resuming from S4.
Finger print: support 10 fingers - Upack/Authentec modules.
Setting a Password
Perform the following steps to set the supervisor, user, or HDD password.
Note: The following example uses the Supervisor Password screens. The User and HDD Password screens
are identical.
1. Use the µ and ¶ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set
Supervisor Password box appears:
2. Type a password in the Enter New Password field. The password length can not exceeds 8 alphanumeric
characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the Confirm New Password field.
IMPORTANT:Be careful when typing the password as the characters do not appear on the screen.
3. Press Enter. After setting the password, the computer sets the Supervisor Password Is parameter to Set.
4. If desired, you can opt to enable the Password on Boot parameter.
5. When you are done, save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1. Use the µ and ¶ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set
Password box appears:
54
Chapter 2
2. Type the current password in the Enter Current Password field and press Enter.
3. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. The
computer then sets the Supervisor Password parameter to Clear.
4. When you have changed the settings, save the changes and exit the BIOS Setup Utility.
Changing a Password
1. Use the µ and ¶ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set
Password box appears:
2. Type the current password in the Enter Current Password field and press Enter.
3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field.
4. Press Enter. After setting the password, the computer sets the Supervisor Password Is parameter to Set.
5. If desired, you can enable the Password on Boot parameter.
6. When you are done, save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses Enter.
If the current password entered does not match the actual current password, the screen will show you the Setup
Warning.
Chapter 2
55
If the new password and confirm new password strings do not match, the screen will display the following
message.
56
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Phoenix - Award WorkstationBIOS CMOS Setup Utility
Boot
Boot Priority Order:
Help Item
1: IDE0: WDC WD200EB - (PM)
2: IDE1: WDC WD200EB - (PM)
Menu Level
X
3: CD/DVD
4: Network Boot
5: USB HDD
6: USB FDD
7: USB Key
8: USB CD/DVD ROM
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
Use µ or ¶ to select a device, then press <F6> to move it up the List, or <F5> to move it down the list. Press
<Esc> to escape the menu
Chapter 2
57
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
Phoenix - Award WorkstationBIOS CMOS Setup Utility
Exit
Exit Saving Changes
Help Item
Exit Discarding Changes
Load Setup Defaults
Menu Level
X
Discard Changes
Save Changes
KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
The table below describes the parameters in this screen.
58
Parameter
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding
Changes
Exit utility without saving setup data to CMOS.
Load Setup Defaults
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
q
New versions of system programs
q
New features or options
q
Restore a BIOS when it becomes corrupted.
Use the Flash utility to update the system BIOS flash ROM.
Note: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Flash utility.
Note: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
Note: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not completely
loaded.
Fellow the steps below to run the Flash.
1. Prepare a bootable diskette.
2. Copy the flash utilities to the bootable diskette.
3. Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
59
60
Chapter 2
Chapter 3
Machine Disassembly and Replacement
General Information
This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance
and troubleshooting.
To disassemble the computer, you need the following tools:
q
Wrist grounding strap and conductive mat for preventing electrostatic discharge
q
Small Philips screw driver
q
Philips screwdriver
q
Plastic flat head screw driver
q
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components. When you
remove the stripe cover, please be careful not to scrape the cover.
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
Chapter 3
61
Disassembly Procedure Flowcharts
The following flowcharts give you a graphic representation on the entire disassembly sequence and instructs you
on the components that need to be removed during servicing. For example, if you want to remove the system
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Main Unit Disassembly Flowchart
62
Chapter 3
LCM Module Disassembly Flowchart
Chapter 3
63
Main Unit Disassembly Procedure
Removing the Battery Pack
1. Turn the computer over. Release the battery
locks as shown.
2. Push and hold release latch.
3. Remove the battery.
Removing the CTO Cover
1. Locate and loosen the seven screws as shown.
Note: It is not necessary to remove the screws
from the CTO Cover.
64
2. Lift the CTO cover using the indented top edge
as shown.
3. Lift to 45° angle and remove from chassis.
Chapter 3
Removing the ODD
1. Push and hold the ODD latch as shown.
2. Remove ODD.
Removing the HDD
1. Locate the plastic tab on the HDD.
2. Place one hand on the computer for stability and
grasp the HDD removal tag.
3. Pull upward as shown to remove the HDD from the chassis.
Removing the BTCB Screws
Locate and remove the twenty (20) BTCB screws as indicated.
Chapter 3
65
Removing the Memory Modules
1. Push the two release levers on the upper module 2. Pull upper memory module away from the
outward as shown.
socket.
Note: The memory module lifts upward during
release.
Note: Use two hand to remove the module by
gripping the top edge as shown.
3. Push the two release levers on the lower module 4. Pull the lower memory module away from the
outward as shown.
socket.
66
Chapter 3
Removing the Wireless Card
Note: Fine tweezers are required for this procedure.
1. Locate the three antenna wires (colored white,
gray, and black) on the right-hand side of the
HDD bay.
2. Using fine tweezers, grip the white wire and pull
upward until it is released from the board.
Repeat for the gray and black wires.
3. Locate the two screws securing the Wireless
Card.
4. Locate and remove the two screws securing the
Wireless Card.
Note: The Wireless Card lifts up automatically
once the screws are removed.
5. Grip card and pull away from socket as shown.
Chapter 3
67
Removing the Switch Cover
CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is
recommended that only fingers are used to remove the Switch Cover.
1. Locate and remove the four securing screws as
shown.
2. Turn the computer over. Open the LCM module
fully to expose the Switch Cover.
Note: Two of the screws are located within the
battery cradle.
3. Grip the Switch Cover as shown and pull upward to remove.
4. Using two hands, remove the Switch Cover from the chassis.
68
Chapter 3
Removing the Keyboard
1. Locate and remove the two screws as shown.
2. Using both hands, lift the top edge of the
keyboard as shown.
3. Turn the keyboard over, as shown, to expose the cables.
4. Using fine tweezers, release the first cable lock as shown and remove the cable from the socket.
5. Using fine tweezers, release the second cable lock as shown and remove the cable from the socket.
Chapter 3
69
6. Remove keyboard from chassis.
Removing the Switch Board
1. Locate and remove the screw as shown.
2. Using fine tweezers, release the cable lock as shown and remove the cable from the socket.
3. Remove the Switch Board from the chassis.
70
Chapter 3
Removing the Antenna Cables
1. Turn the computer over. Remove the Antenna Cables from the three securing pins as shown.
2. Turn the computer over. Locate the socket as indicated.
3. Using fine tweezers, disconnect the cable as shown.
Chapter 3
71
4. Pull the black MIC cable through the mainboard.
5. Pull the white and gray cables through the
mainboard.
Note: This cable is not attached to the LCM
Module. Move the cable out of the work area to
avoid damage.
6. Remove the two gray cables and the white cable from the securing pins as shown.
72
Chapter 3
Removing the LCM Module
CAUTION: Ensure all cables are removed from securing pins before proceeding to avoid damage.
1. Locate and remove the four screws as shown.
2. Locate and remove the two screws from the rear
of the computer as shown.
Note: The earth wire is disconnected when the
screws are removed.
3. Disconnect the cable from the connector as shown.
4. Using two hands, lift the LCM Module clear and remove from the chassis as shown.
Chapter 3
73
Removing the TouchPad
1. Locate the TouchPad cable as shown.
2. Using tweezers, release the locking latch and disconnect the cable as shown.
3. Using both hands, remove the casing and TouchPad as shown.
Removing the Mainboard
1. Locate the two screws (red markers) and two connectors (yellow markers) as shown.
74
Chapter 3
2. Remove the screws and disconnect the connectors using tweezers as shown.
3. Open the VGA Port cover as shown.
CAUTION: If the VGA Port cover is left closed,
damage to the mainboard may result.
4. Grip the mainboard from the rear and lift up.
Note: If any resistance is met while removing the
mainboard, ease the computer case outward to
clear the obstruction.
5. Lift the mainboard clear of the chassis.
Chapter 3
75
Removing the Heatsink and Fan Module
1. Locate and remove the two screws from the
mainboard.
2. Turn the mainboard over. Locate the connector
and two screws as shown.
3. Remove the two screws and the Heatsink securing bracket as shown.
4. Hold the Fan unit with one hand and remove the Heatsink as shown.
5. Disconnect the Fan cable as shown.
76
6. Remove the Fan Module by lifting straight up.
Chapter 3
Removing the CPU
1. Using a screw driver, unscrew the CPU counter
clockwise.
Chapter 3
2. Remove the CPU from the bracket as shown.
77
LCM Module Disassembly Procedure
Removing the LCM Bezel
CAUTION: When using tools, be careful not to scratch the computer casing.
1. Locate and remove the four mylar (small red markers) and two rubber (large red markers) screw covers
as shown. Remove the six bezel securing screws.
Note: Do not discard the screw covers — they are reusable.
2. Loosen the bezel by lifting all the edges upward as shown.
3. Push in the cover locks to allow the bezel to pass 4. Remove the bezel from the LCM Module.
freely over them.
78
Chapter 3
Removing the LCD Panel
1. Locate and remove the six screws as shown.
2. Locate the three panel connectors as shown. Disconnect the cables as shown.
3. Hold down the WebCam Module and remove the LCD panel by lifting the hinge as shown.
Chapter 3
79
4. Locate and remove the Inverter Board screw as
shown.
5. Grip the Inverter Board and lift upward to remove.
6. Grip the WebCam Module and lift upward to remove.
7. Turn the LCD panel over to expose the rear. Grip the LCM cable and lift upward to detach the adhesive
pads.
8. Hold the printed circuit board with one hand and disconnect the cable by pulling away from the
connector.
80
Chapter 3
9. Locate and remove the four screws (two on each side) securing the LCD brackets to the LCD panel.
10. Remove the LCD brackets by pulling away from the LCD Panel as shown.
Chapter 3
81
LCM Module Reassembly Procedure
Replacing the LCD Panel
1. Align the LCD brackets with the four screw holes (two on each side) on the LCD Panel as shown.
2. Secure the LCD brackets to the LCD panel.
3. Turn the panel over. Insert the cable into the cable connector on the LCD Panel as shown.
4. Align the LCD Panel cable as shown and press down to engage the adhesive pads.
82
Chapter 3
5. Place the WebCam Module in the mounting as shown.
6. Place the Inverter Board in the mounting and secure with the screw provided.
7. Place the LCD Panel in the mounting and secure the three panel connectors as shown.
Chapter 3
83
8. Secure the LCD Panel with the six screws provided.
Replacing the LCM Bezel
1. Locate the bezel correctly and press down the edges until there are no gaps between the bezel and the
LCM Module,
2. Secure the six screws provided and replace the mylar (small red markers) and rubber screw caps (large
red markers).
84
Chapter 3
Main Module Reassembly Procedure
Replacing the CPU
1. Insert the CPU into the CPU bracket as shown.
2. Using a screw driver, tighten the screw clockwise
as shown to secure the CPU in place.
Replacing the Heatsink and Fan Module
1. Place the Fan Module in the mounting as shown. 2. Connect the Fan Module cable as shown.
3. Hold the Fan Module in place and place the Heatsink as shown.
4. Align the Heatsink Securing Bracket correctly and fix in place using the two screws provided.
Chapter 3
85
5. Turn the Mainboard over and secure the two screws as shown.
Replacing the Mainboard
CAUTION: Ensure that the VGA Port Cover is open before beginning. Failure to do so may result in damage
to the Mainboard.
1. Ensure that the Mainboard is face up (the Fan Module and CPU are not visible). Place the Mainboard in
the chassis and press down to install.
Note: If any resistance is met while installing the mainboard, ease the computer case outward to clear
the obstruction.
2. Close the VGA Port and connect the two speaker cables to the Mainboard as shown.
86
Chapter 3
3. Secure the Mainboard to the chassis using the two screws provided (red markers).
Chapter 3
87
Replacing the TouchPad
1. Using both hands, replace the TouchPad as shown.
Note: Ensure that the TouchPad cable is accessible once the TouchPad is in place.
2. Using tweezers, grip the TouchPad cable and insert it into the connector on the Motherboard as shown.
Secure the locking latch to hold the cable in place.
Replacing the LCM Module
1. Align the four screw holes on the LCM Module hinges with the corresponding screw holes on the
chassis. Lower the LCM Module into position as shown. Ensure that the LCM cables are inserted
through the aperture before proceeding (yellow marker).
2. Connect the LCM Module cable to the connector on the chassis as shown.
88
Chapter 3
3. Secure the two screws at the rear of the computer as shown and the four screws to hold the LCM in
place on the chassis.
Note: Ensure that the earth wire is reconnected during this step.
Replacing the Antenna Cables
1. Place the three cables from the LCM Module in the wiring conduit and secure in place using the cable
pins on the chassis.
2. Push the black MIC cable from the left hand side of the computer, the white cable and the gray cable
through the Mainboard so that they are accessible from underneath the computer.
Chapter 3
89
3. Using tweezers, secure the remaining gray cable with the connector to the port on the Mainboard.
4. Turn the computer over. Place the three cables from the LCM Module in the wiring conduit and secure in
place using the cable pins on the chassis.
90
Chapter 3
Replacing the Switch Board
1. Place the Switch Board in the mounting as shown.
2. Insert the cable into the port and secure the locking latch using fine tweezers.
3. Secure the Switch Board in place using the screw provided.
Replacing the Keyboard
1. Using fine tweezers, insert the thicker cable into the socket and secure the locking latch as shown.
Chapter 3
91
2. Using fine tweezers, insert the remaining cable into the socket and secure the locking latch as shown.
3. Turn the keyboard over and place the front edge first into the mounting.
4. Push the Keyboard into place toward the TouchPad and secure using the two screws provided.
92
Chapter 3
Replacing the Switch Cover
1. Place the Switch Cover as shown and press down until no gaps are visible between the cover and the
chassis.
2. Close the LCM Module and turn the computer over. Locate and replace the four screws as shown.
Note: Two of the screws are located within the battery cradle.
Replacing the Wireless Card
1. Ensure the card is positioned label upwards as
shown and push into the connector.
2. Secure the card in position using the two screws
provided.
Note: The card remains at an angle until the
screws are inserted.
Chapter 3
93
3. Reconnect the three Antenna Cables as shown, pushing down firmly to connect the cables.
Cable Color
Connector Number
Black
1
White
2
Gray
3
Replacing the Memory Modules
1. Using two hands, push the lower module into the socket until it clicks into place.
2. Using two hands, push the upper module into the socket and press downward until it clicks into place.
94
Chapter 3
Replacing the BTCB Screws
1. Locate and secure the twenty (20) BTCB screws as shown.
Replacing the HDD
1. Place the HDD in the mounting, rear edge first as 2. Push down firmly into the mounting to secure the
shown.
HDD.
Replacing the ODD
1. Brace the computer with one hand and insert the 2. Push the ODD until it is fully inserted i.e. the ODD
ODD into the bay as shown.
is flush with the chassis casing.
Chapter 3
95
Replacing the CTO Cover
1. Place the CTO Cover rear edge first on to the
chassis as shown.
2. Push down fully until no gaps are visible between
the CTO Cover and the chassis.
3. Secure the CTO Cover using the seven screws provided.
Replacing the Battery Pack
1. Place the battery in the cradle as shown.
2. Push the battery toward the computer until it
clicks in to place.
3. Engage the battery locks as shown.
96
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
Note: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1. Obtain the failing symptoms in as much detail as possible.
2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the
same operation.
3. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does
not go on or stay on.)
“Power System Check” on page 99.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error
Message” on page 101
“Undetermined Problems” on page 115
POST detects an error and displayed
messages on screen.
“Error Message List” on page 102
Other symptoms (i.e. LCD display problems “Power-On Self-Test (POST) Error
or others).
Message” on page 101
Symptoms cannot be re-created
(intermittent problems).
Chapter 4
Use the customer-reported symptoms and
go to “Power-On Self-Test (POST) Error
Message” on page 101
“Intermittent Problems” on page 114
“Undetermined Problems” on page 115
97
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
Note: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if FDD Test is passed as the program runs to FDD Test.
3. Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1. Reconnect the external diskette drive/DVD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does not
have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3. Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1. Reconnect the external diskette drive/CD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a nondefective FRU:
1. Reconnect the keyboard cables.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer:
q
Numeric keypad
q
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
98
Chapter 4
1. Boot from the diagnostics diskette and start the diagnostic program (please refer to main board.
2. Go to the diagnostic memory in the test items.
3. Press F2 in the test items.
4. Follow the instructions in the message window.
Note: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1. Remove the battery pack.
2. Connect the power adapter and check that power is supplied.
3. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by the
battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
q
“Check the Power Adapter” on page 99
q
“Check the Battery Pack” on page 99
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
1. If the voltage is not correct, replace the power adapter.
2. If the voltage is within the range, do the following:
q
Replace the System board.
q
If the problem is not corrected, see “Undetermined Problems” on page 115.
q
If the voltage is not correct, go to the next step.
Note: An audible noise from the power adapter does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adapter for correct continuity and
installation.
4. If the operational charge does not work, see “Check the Battery Pack” on page 99.
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1. Check out the Power Management in control Panel
2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery
Power Remaining are correct.
3. Repeat the steps 1 and 2, for both battery and adapter.
4. This helps you identify first the problem is on recharging or discharging.
From Hardware:
1. Power off the computer.
Chapter 4
99
2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% of
the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature. Reinstall the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light up,
replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a nondefective FRU:
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement can
occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem.
No service actions are necessary if the pointer movement stops in a short period of time.
100
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is listed
first.
Note: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 115.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified by
function.
Note: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it
has been configured.
Note: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
101
Index of Error Messages
Error Code List
Error Codes
Error Messages
006
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment
Configuration Error”)
010
Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
<No error code>
Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut
down system, no message will show.
<No error code>
Thermal critical High
In this situation BIOS will shut down system, not show
message.
Error Message List
102
Error Messages
FRU/Action in Sequence
Failure Fixed Disk
Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see “Keyboard or Auxiliary Input Device Check” on page 98.
Keyboard error
see “Keyboard or Auxiliary Input Device Check” on page 98.
Keyboard Controller Failed
see “Keyboard or Auxiliary Input Device Check” on page 98.
Keyboard locked - Unlock key switch
Unlock external keyboard
Monitor type does not match CMOS - Run
Setup
Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn
BIOS ROM
System board
System RAM Failed at offset: nnnn
DIMM
System board
Extended RAM Failed at offset: nnnn
DIMM
System board
System battery is dead - Replace and run
Setup
Replace RTC battery and Run BIOS Setup Utility to
reconfigure system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
Chapter 4
Error Message List
Error Messages
FRU/Action in Sequence
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Previous boot incomplete - Default
configuration used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in
BIOS Setup Utility
See “External Diskette Drive Check” on page 98.
Incorrect Drive A type - run SETUP
Check the drive is defined with the proper diskette type in
BIOS Setup Utility
System cache error - Cache disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly
identified.
Diskette drive
Hard disk drive
System board
Chapter 4
103
Error Message List
104
No beep Error Messages
FRU/Action in Sequence
No beep, power-on indicator turns off and
LCD is blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 99..
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and
LCD is blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 99..
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and
LCD is blank. But you can see POST on an
external CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during
POST.
Ensure every connector is connected tightly and correctly.
System board
No beep during POST but system runs
correctly.
Speaker
System board
Chapter 4
Phoenix BIOS Beep Codes
Code
Beeps
POST Routine Description
02h
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm
boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
BIOS ROM checksum
17h
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
Test DRAM refresh
22h
1-3-1-3
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte
of memory bus
2Fh
30h
Enable cache before system BIOS
shadow
1-4-1-1
RAM failure on data bits xxxx of high byte
of memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
Chapter 4
105
Code
Beeps
3Ch
Advanced configuration of chipset
registers
3Dh
Load alternate registers with CMOS
values
42h
Initialize interrupt vectors
45h
POST device initialization
46h
2-1-2-3
48h
Check ROM copyright notice
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
58h
106
POST Routine Description
Set key click if enabled
2-2-3-1
Test for unexpected interrupts
59h
Initialize POST display service
5Ah
Display prompt “Press F2 to enter
SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM)
area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and
IRQs
81h
Late POST device initialization
Chapter 4
Code
Beeps
POST Routine Description
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable
Devices (optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives
(optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor
boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two
short beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI
drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
POST done- prepare to boot operating
system
B4h
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
Chapter 4
107
Code
Beeps
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
D2h
Unknown interrupt
Code
Beeps
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
F4h
108
POST Routine Description
Initialize System Management Mode
1
Output one beep before boot
Chapter 4
Code
Beeps
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
109
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
Action in Sequence
LCD backlight doesn't work
LCD is too dark
LCD brightness cannot be adjusted
LCD contrast cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”,
then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key doesn't
work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Action in Sequence
Indicator incorrectly remains off or on, but
system runs correctly
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
110
Symptom / Error
Action in Sequence
Power shuts down during operation
Power source (battery pack and power adapter). See “Power
System Check” on page 99.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 99.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” on page 99.
Hold and press the power switch for more than 4 seconds.
System board
Chapter 4
Power-Related Symptoms
Symptom / Error
Action in Sequence
Battery can’t be charged
See “Check the Battery Pack” on page 99.
Battery pack
System board
PCMCIA-Related Symptoms
Symptom / Error
Action in Sequence
System cannot detect the PC Card
(PCMCIA)
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Action in Sequence
Memory count (size) appears different from
actual size.
Enter BIOS Setup Utility to execute “Load Default Settings,
then reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
In Windows, multimedia programs, no
sound comes from the computer.
Audio driver
Speaker
System board
Internal speakers make noise or emit no
sound.
Speaker
System board
Power Management-Related Symptoms
Symptom / Error
Action in Sequence
The system will not enter hibernation
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode
and four short beeps every minute.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode
after closing the LCD
LCD cover switch
System board
The system doesn't resume from
hibernation mode.
Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby
mode after opening the LCD.
LCD cover switch
System board
Chapter 4
111
Power Management-Related Symptoms
Symptom / Error
Action in Sequence
Battery fuel gauge in Windows doesn’t go
higher than 90%.
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then
charge battery).
Battery pack
System board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”,
then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
System board
USB does not work correctly
System board
Print problems.
Ensure the “Parallel Port” in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems.
Ensure the “Serial Port” in the Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Action in Sequence
Keyboard (one or more keys) does not
work.
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error
Action in Sequence
Internal modem does not work correctly.
Modem phone port
modem combo board
System board
Note: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
112
Chapter 4
Problems” on page 115.
Chapter 4
113
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware
defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
114
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
Note: Verify that all attached devices are supported by the computer.
Note: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 99.):
1. Power-off the computer.
2. Visually check them for damage. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
q
Non-Acer devices
q
Printer, mouse, and other external devices
q
Battery pack
q
Hard disk drive
q
DIMM
q
CD-ROM/Diskette drive Module
q
PC Cards
4. Power-on the computer.
5. Determine if the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
Chapter 4
q
System board
q
LCD assembly
115
116
Chapter 4
Chapter 5
Jumper and Connector Locations
Connector Locations
Top View
Item
Name
Description
Item
Name
Description
1
CN2
S-Video
12
CN34
Bluetooth Cable CNTR
2
CN4
LCM Cable CNTR
13
CN32
Speaker Cable CNTR
3
CN7
3G Card CNTR
14
Jack5
Headphone Jack
4
CN8
Hot Keyboard CNTR
15
Jack3
Line-In Jack
5
CN12
Keyboard FFC CNTR
16
Jack4
MIC Jack
6
CN13
Fine Track FFC CNTR
17
CN27
5 in 1 Card Reader Socket
7
CN18
MIC Cable CNTR
18
CN33
Speaker CAble CNTR
8
CN20
TouchPad FFC CNTR
19
CN24
PCMCIA Socket
9
CN19
SmartCard CAble CNTR
20
CN26
PCMCIA Socket
10
CN28
MDC CNTR
21
CN22
USB
Chapter 5
117
Item
Name
Description
Item
Name
Description
11
CN29
IO Board CNTR
22
D47
IR Receiver
Bottom View
118
Item
Name
Description
Item
Name
Description
1
Jack500
DC In Jack
11
U512
South Bridge
2
CN500
Serial Port
12
CN515
W/LAN Card CNTR
3
CN501
Fan Cable CNTR
13
CN511
ODD CNTR
4
CN508
1394
14
CN510
HDD CNTR
5
Jack501
Ethernet jack and RJ11 Jack
15
CN507
Second Battery CNTR
6
U507
North Bridge
16
CN506
RTC Battery CNTR
7
U505
CPU Socket
17
CN505
MDC Cable CNTR
8
CN509
MDC Cable CNTR
18
CN504
MainBoard and IO Board CNTR
9
CN512
DIMM Socket
19
CN503
Docking CNTR
10
CN513
DIMM Socket
20
CN502
Battery CNTR
Chapter 5
Connector Pin Definitions
CN4 LCD I/F Connector (40-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
+V5S
-
21
LVDS_TXDL2+
O
2
INV_PWM_3
O
22
GND
-
3
+V5S
-
23
LVDS_TXDL2-
O
4
GND
O
24
LVDS_TXDL1+
O
5
BKLTEN
O
25
GND
-
6
LVDS_TXCU+
O
26
LVDS_TXDL1-
O
7
GND
-
27
LVDS_TXDL0+
O
8
LVDS_TXCU-
O
28
GND
-
9
LVDS_TXDU2+
O
29
LVDS_TXDL0-
O
10
GND
-
30
LCM_DDCPDATA
O
11
LVDS_TXDU2-
O
31
GND
-
12
LVDS_TXDU1+
O
32
NC
-
13
GND
-
33
LCM_DDCPCLK
O
14
LVDS_TXDU1-
O
34
+V3S_DSC
-
15
LVDS_TXDU0+
O
35
GND
-
16
GND
-
36
+V3S
O
17
LVDS_TXDU0-
O
37
USB_PN6
O
18
LVDS_TXCL+
O
38
+V3S_LCM
O
19
GND
-
39
USB_PP6
O
20
LVDS_TXCL-
O
40
+V3S_LCM
O
CN20 Touch PAD I/F Connector (12-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
+5S
-
7
GND
-
2
+5S
-
8
GND
-
3
IM_CLOCK
O
9
USB_P5+
I/O
4
IM_DATA
O
10
USB_P5-
I/O
5
IM_CLOCK1
O
11
NC
-
6
IM_DATA1
O
12
+V3S
-
CN12 Keyboard I/F Connector (25-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
SCAN_IN(0)
O
14
SCAN_IN(4)
O
2
SCAN_IN(1)
O
15
SCAN_OUT(9)
O
3
SCAN_IN(2)
O
16
SCAN_IN(5)
O
4
SCAN_OUT(0)
O
17
SCAN_IN(6)
O
5
SCAN_OUT(1)
O
18
SCAN_OUT(10)
O
6
SCAN_OUT(2)
O
19
SCAN_OUT(11)
O
7
SCAN_IN(3)
O
20
SCAN_IN(7)
O
8
SCAN_OUT(3)
O
21
SCAN_OUT(12)
O
9
SCAN_OUT(4)
O
22
SCAN_OUT(12)
O
10
SCAN_OUT(5)
O
23
XSCAN_OUT(14)
O
Chapter 5
119
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
11
SCAN_OUT(6)
O
24
SCAN_OUT(15)
O
12
SCAN_OUT(7)
O
13
SCAN_OUT(8)
O
-
CN27 Cardreader Connector-TD (43-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
SD_D2
I/O
23
SD_WP_SM_WPI#
I/O
2
GND
-
24
GND
-
3
SD_D3
I/O
25
GND
-
4
+V3S
-
26
XD_CD#
I/O
5
SD_MS_CLK
I/O
27
XD_R_B#
I/O
6
SD_CMD
I/O
28
XD_RE#
I/O
7
MS_D3_XD_D0
I/O
29
XD_CE#
I/O
8
GND
-
30
XD_CLE
I/O
9
MS_CD#
I/O
31
XD_ALE
I/O
10
MS_D2_XD_D1
I/O
32
XD_WE#
I/O
11
+V3S
-
33
XD_WPO#
I/O
12
MS_D0_XD_D2
I/O
34
GND
-
13
MS_D1_XD_D7
I/O
35
MS_D3_XD_D0
I/O
14
SD_MS_CLK
I/O
36
MS_D2_XD_D1
I/O
15
MS_S_XD_D3
I/O
37
MS_D0_XD_D2
I/O
16
GND
-
38
MS_BS_XD_D3
I/O
17
GND
-
39
XD_D4
I/O
18
SD_D0
I/O
40
XD_D5
I/O
19
SD_D1
I/O
41
XD_D6
I/O
20
SD_CD#
I/O
42
MS_D1_XD_D7
I/O
21
GND
-
43
+V3S
-
22
GND
-
JACK501 RJ45&RJ11 Connector (14-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
MDMTIP
O
8
RD-
I
2
MDMRNG
O
9
D+
I/O
3
TD+
O
10
D-
I/O
4
TD-
O
A1
+V3M_LAN
-
5
RD+
I
A2
LAN_MB_LINKLED#
I
6
C+
I/O
B1
+V3M_LAN
-
7
C-
I/O
B2
LAN_MB_ACTLED#
I
CN7 CRT I/F Connector (15-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
RED
O
9
+V5S_SYNC
-
2
GREEN
O
10
GND
-
3
BLUE
O
11
NC
-
4
NC
-
12
U_CRT_DDCDATA
I/O
120
Chapter 5
CN7 CRT I/F Connector (15-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
5
CRTDECT#
I
13
HSYNC
O
6
GND
-
14
VSYNC
O
7
GND
-
15
U_CRT_DDCCLK
O
8
GND
-
CN501 Fan Connector (3-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
FAN1_PWM_3
-
3
FAN_TACH1
O
2
GND
-
-
-
-
CN504 Board to Board Connector (30-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
BUF_PLT_RST#
O
21
+V3S
-
2
WXMIT_OFF#
-
22
GND
-
3
UIM_VPP
I/O
23
USB_P8-
I/O
4
UIM_RST
I/O
24
USB_P8+
I/O
5
UIM_CLK
I/O
25
GND
-
6
UIM_DATA
I/O
26
WWAN_LED#
-
7
UIM_PWR-
I/O
27
+V3S
-
8
GND
-
28
+V3S
-
9
GND
-
29
GND
-
10
+V3S
-
30
GND
-
11
+V3S
-
31
SDTR#_3
I/O
12
+V5A_USB2
-
32
STXD_3
I/O
13
+V5A_USB2
-
33
SRTS#_3
I/O
14
+V5A_USB2
-
34
SRI#_3
I/O
15
+V5A_USB2
-
35
SCTS#_3
I/O
16
GND
-
36
SRXD_3
I/O
17
GND
-
37
SDSR#_3
I/O
18
USB_P0-
I/O
38
SDCD#_3
I/O
19
USB_P0+
I/O
39
DOCK_DETECT#_3S
I
20
GND
I/O
40
+V3S
-
CN513 Memory Connector 0 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
M_VREF
-
2
GND
-
3
GND
-
4
MA_DATA4
I/O
5
MA_DATA1
I/O
6
MA_DATA5
I/O
7
MA_DATA0
I/O
8
GND
-
9
GND
-
10
MB_DM0
I/O
11
MB_DQS#0
I/O
12
GND
-
13
MB_DQS0
I/O
14
MA_DATA7
I/O
15
GND
-
16
MA_DATA6
I/O
17
MA_DATA2
I/O
18
GND
-
Chapter 5
121
CN513 Memory Connector 0 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
19
MA_DATA3
I/O
20
MA_DATA9
I/O
21
GND
-
22
MA_DATA13
I/O
23
MA_DATA12
I/O
24
GND
-
25
MA_DATA8
I/O
26
MB_DM1
I/O
27
GND
-
28
GND
-
29
MB_DQS#1
I/O
30
M_CLKOUT0
I
31
MB_DQS1
I/O
32
M_CLKOUT0#
I
33
GND
-
34
GND
-
35
MA_DATA10
I/O
36
MA_DATA15
I/O
37
MA_DATA11
I/O
38
MA_DATA14
I/O
39
GND
-
40
GND
-
41
GND
-
42
GND
-
43
MA_DATA17
I/O
44
MA_DATA20
I/O
45
MA_DATA21
I/O
46
MA_DATA19
I/O
47
GND
-
48
GND
-
49
MA_DQS#2
I/O
50
N.C.
-
51
MA_DQS2
I/O
52
MA_DM2
I/O
53
GND
-
54
GND
-
55
MA_DATA23
I/O
56
MA_DATA22
I/O
57
MA_DATA22
I/O
58
MA_DATA16
I/O
59
GND
-
60
GND
-
61
MA_DATA29
I/O
62
MA_DATA24
I/O
63
MA_DATA28
I/O
64
MA_DATA25
I/O
65
GND
-
66
GND
-
67
MA_DM3
I/O
68
MA_DQS#3
I/O
69
N.C.
-
70
MA_DATA3
I/O
71
GND
-
72
GND
-
73
MA_DATA31
I/O
74
MA_DATA26
I/O
75
MA_DATA30
I/O
76
MA_DATA27
I/O
77
GND
I/O
78
GND
-
79
M_CKE0
I
80
M_CKE1
I
81
+1.8VSUS
-
82
+1.8VSUS
-
83
MA_CS#2
I
84
MA_A15
I
85
MA_BS#2
I
86
MA_A14
I
87
+1.8VSUS
-
88
+1.8VSUS
-
89
MA_A12
I
90
MA_A11
I
91
MA_A9
I
92
MA_A7
I
93
MA_A8
I
94
MA_A6
I
95
+1.8VSUS
-
96
+1.8VSUS
-
97
MA_A5
I
98
MA_A4
I
99
MA_A3
I
100
MA_A2
I
101
MA_A1
I
102
MA_A0
I
122
Chapter 5
CN513 Memory Connector 0 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
103
+1.8VSUS
-
104
+1.8VSUS
-
105
MA_A10
I
106
MA_BS#1
I
107
MA_BS#0
I
108
MA_RAS#
I
109
MA_WE#
I
110
MA_CS#0
I
111
+1.8VSUS
-
112
+1.8VSUS
-
113
MA_CAS#
-
114
M_ODT0
I
115
MA_CS#0
I
116
MA_A13
I
117
+1.8VSUS
-
118
+1.8VSUS
-
119
M_ODT1
I
120
N.C.
-
121
GND
-
122
GND
-
123
MA_DATA32
I/O
124
MA_DATA33
I/O
125
MA_DATA36
I/O
126
MA_DATA38
I/O
127
GND
-
128
GND
-
129
MA_DQS#4
I/O
130
MA_DM4
I/O
131
MA_DQS4
I/O
132
GND
-
133
GND
-
134
MA_DATA34
I/O
135
MA_DATA37
I/O
136
MA_DATA39
I/O
137
MA_DATA35
I/O
138
GND
-
139
GND
-
140
MA_DATA44
I/O
141
MA_DATA40
I/O
142
MA_DATA45
I/O
143
MA_DATA41
-
144
GND
-
145
GND
-
146
MA_DATA19
I/O
147
MA_DM5
I/O
148
MA_DQS5
I/O
149
GND
-
150
GND
-
151
MA_DATA42
I/O
152
MA_DATA43
I/O
153
MA_DATA46
I/O
154
MA_DATA47
I/O
155
GND
-
156
GND
-
157
MA_DATA49
I/O
158
MA_DATA53
I/O
159
MA_DATA52
I/O
160
MA_DATA48
I/O
161
GND
-
162
GND
-
163
N.C.
-
164
M_CLKOUT1
I
165
GND
-
166
M_CLKOUT1#
I
167
MA_DQS#6
I/O
168
GND
-
169
MA_DQS6
I/O
170
MA_DM6
I/O
171
GND
-
172
GND
-
173
MA_DATA50
I/O
174
MA_DATA55
I/O
175
MA_DATA51
I/O
176
MA_DATA54
I/O
177
GND
-
178
GND
-
179
MA_DATA60
I/O
180
MA_DATA57
I/O
181
MA_DATA56
I/O
182
MA_DATA61
I/O
183
GND
-
184
GND
-
185
MA_DM7
I/O
186
MA_DQS#7
I/O
Chapter 5
123
CN513 Memory Connector 0 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
187
GND
-
188
MA_DQS7
I/O
189
MA_DATA58
I/O
190
GND
-
191
MA_DATA63
I/O
192
MA_DATA59
I/O
193
GND
-
194
MA_DATA62
I/O
195
PDAT_SMB
I/O
196
GND
-
197
PCLK_SMB
I/O
198
GND
-
199
+3V
-
200
GND
-
CN512 Memory Connector 1 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
MVREF_DM1
-
2
GND
-
3
GND
-
4
MB_DATA4
I/O
5
MB_DATA1
I/O
6
MB_DATA5
I/O
7
MB_DATA0
I/O
8
GND
-
9
GND
-
10
MB_DM0
I/O
11
MB_DQS#0
I/O
12
GND
-
13
MB_DQS0
I/O
14
MB_DATA7
I/O
15
GND
-
16
MB_DATA6
I/O
17
MB_DATA2
I/O
18
GND
-
19
MB_DATA3
I/O
20
MB_DATA9
I/O
21
GND
-
22
MB_DATA13
I/O
23
MB_DATA12
I/O
24
GND
-
25
MB_DATA8
I/O
26
MB_DM1
I/O
27
GND
-
28
GND
-
29
MB_DQS#1
I/O
30
M_CLKOUT0
I
31
MB_DQS1
I/O
32
M_CLKOUT0#
I
33
GND
-
34
GND
-
35
MB_DATA10
I/O
36
MB_DATA15
I/O
37
MB_DATA11
I/O
38
MB_DATA14
I/O
39
GND
-
40
GND
-
41
GND
-
42
GND
-
43
MB_DATA17
I/O
44
MB_DATA20
I/O
45
MB_DATA21
I/O
46
MB_DATA19
I/O
47
GND
-
48
GND
-
49
MB_DQS#2
I/O
50
N.C.
-
51
MB_DQS2
I/O
52
MB_DM2
I/O
53
GND
-
54
GND
-
55
MB_DATA23
I/O
56
MB_DATA22
I/O
57
MB_DATA22
I/O
58
MB_DATA16
I/O
59
GND
-
60
GND
-
61
MB_DATA29
I/O
62
MB_DATA24
I/O
63
MB_DATA28
I/O
64
MB_DATA25
I/O
65
GND
-
66
GND
-
124
Chapter 5
CN512 Memory Connector 1 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
67
MB_DM3
I/O
68
MB_DQS#3
I/O
69
N.C.
-
70
MB_DQS3
I/O
71
GND
-
72
GND
-
73
MB_DATA31
I/O
74
MB_DATA26
I/O
75
MB_DATA30
I/O
76
MB_DATA27
I/O
77
GND
I/O
78
GND
-
79
M_CKE0
I
80
M_CKE1
I
81
+1.8VSUS
-
82
+1.8VSUS
-
83
MB_CS#2
I
84
MB_A15
I
85
MB_BS#2
I
86
MB_A14
I
87
+1.8VSUS
-
88
+1.8VSUS
-
89
MB_A12
I
90
MB_A11
I
91
MB_A9
I
92
MB_A7
I
93
MB_A8
I
94
MB_A6
I
95
+1.8VSUS
-
96
+1.8VSUS
-
97
MB_A5
I
98
MB_A4
I
99
MB_A3
I
100
MB_A2
I
101
MB_A1
I
102
MB_A0
I
103
+1.8VSUS
-
104
+1.8VSUS
-
105
MB_A10
I
106
MB_BS#1
I
107
MB_BS#0
I
108
MB_RAS#
I
109
MB_WE#
I
110
MB_CS#0
I
111
+1.8VSUS
-
112
+1.8VSUS
-
113
MB_CAS#
-
114
M_ODT0
I
115
MB_CS#0
I
116
MB_A13
I
117
+1.8VSUS
-
118
+1.8VSUS
-
119
M_ODT1
I
120
N.C.
-
121
GND
-
122
GND
-
123
MB_DATA32
I/O
124
MB_DATA33
I/O
125
MB_DATA36
I/O
126
MB_DATA38
I/O
127
GND
-
128
GND
-
129
MB_DQS#4
I/O
130
MB_DM4
I/O
131
MB_DQS4
I/O
132
GND
-
133
GND
-
134
MB_DATA34
I/O
135
MB_DATA37
I/O
136
MB_DATA39
I/O
137
MB_DATA35
I/O
138
GND
-
139
GND
-
140
MB_DATA44
I/O
141
MB_DATA40
I/O
142
MB_DATA45
I/O
143
MB_DATA41
-
144
GND
-
145
GND
-
146
MB_DQS5#
I/O
147
MB_DM5
I/O
148
MB_DQS5
I/O
149
GND
-
150
GND
-
Chapter 5
125
CN512 Memory Connector 1 (200-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
151
MB_DATA42
I/O
152
MB_DATA43
I/O
153
MB_DATA46
I/O
154
MB_DATA47
I/O
155
GND
-
156
GND
-
157
MB_DATA49
I/O
158
MB_DATA53
I/O
159
MB_DATA52
I/O
160
MB_DATA48
I/O
161
GND
-
162
GND
-
163
N.C.
-
164
M_CLKOUT1
I
165
GND
-
166
M_CLKOUT1#
I
167
MB_DQS#6
I/O
168
GND
-
169
MB_DQS6
I/O
170
MB_DM6
I/O
171
GND
-
172
GND
-
173
MB_DATA50
I/O
174
MB_DATA55
I/O
175
MB_DATA51
I/O
176
MB_DATA54
I/O
177
GND
-
178
GND
-
179
MB_DATA60
I/O
180
MB_DATA57
I/O
181
MB_DATA56
I/O
182
MB_DATA61
I/O
183
GND
-
184
GND
-
185
MB_DM7
I/O
186
MB_DQS#7
I/O
187
GND
-
188
MB_DQS7
I/O
189
MB_DATA58
I/O
190
GND
-
191
MB_DATA63
I/O
192
MB_DATA59
I/O
193
GND
-
194
MB_DATA62
I/O
195
PDAT_SMB
I/O
196
GND
-
197
PCLK_SMB
I/O
198
GND
-
199
+3V
-
200
GND
-
CN2 S-Video (7-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
GND
-
2
GND
-
3
LUMA
-
4
CHROMA
O
5
NC
-
6
NC
-
7
NC
O
8
9
-
-
CN511 Multi-Bay Connector (50-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
N.C.
-
2
+V5S_ODD
-
3
+V5S_ODD
-
4
+V5S_ODD
-
5
BAY_ID1
I
6
BAY_ID0
I/O
7
PIDE_3S_CS#(1)
I/O
8
PIDE_3S_A(2)
I/O
9
PDIAG#
I/O
10
NC
I/O
11
PIDE_3S_DACK#
I/O
12
GND
I/O
13
PIDE_3S_IOR#
I/O
14
PIDE_3S_DREQ
I/O
126
Chapter 5
CN511 Multi-Bay Connector (50-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
15
PIDE_3S_D(15)
I/O
16
PIDE_3S_D(14)
I/O
17
PIDE_3S_D(13)
I/O
18
PIDE_3S_D(12)
I/O
19
PIDE_3S_D(11)
I/O
20
PIDE_3S_D(10)
I/O
21
PIDE_3S_D(9)
I/O
22
PIDE_3S_D(8)
I
23
GND
-
24
SATA_SB_C_TXN1
O
25
SATA_SB_C_TXP1
O
26
GND
-
27
+V3S
-
28
+V3S
O
29
BAY_INS#
I
30
GND
-
31
CD_LED#
I
32
PIDE_3S_CS#(0)
O
33
PIDE_3S_A(0)
O
34
PIDE_3S_A(1)
O
35
PIDE_3S_IRQ_R
O
36
PIDE_3S_IORDY
O
37
PIDE_3S_LOW#
I
38
GND
-
39
PIDE_3S_D(0)
I/O
40
PIDE_3S_D(1)
-
41
PIDE_3S_D(2)
I/O
42
PIDE_3S_D(3)
-
43
PIDE_3S_D(4)
I/O
44
PIDE_3S_D(5)
-
45
PIDE_3S_D(6)
I/O
46
PIDE_3S_D(7)
-
47
+V5S
-
48
GND
-
49
SATA_SB_C_RXN1
I
50
SATA_SB_C_RXP1
-
CN22 USB Connector (4-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
+V5A_USB1
-
2
USBP1-
I/O
3
USBP1+
I/O
4
GND
-
CN506 RTC Battery Holder (2-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
+V_RTC
-
2
GND
-
CN510 HDD I/F Connector (22-PIN,SATA)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
GND
-
2
SATA_SB_C_TXP0
O
3
SATA_SB_C_TXN0
O
4
GND
-
5
SATA_SB_C_RXP0
I
6
SATA_SB_C_RXN0
I
7
GND
-
8
NC
-
9
NC
-
10
NC
-
11
GND
-
12
GND
-
13
GND
-
14
+V5S
-
15
+V5S
-
16
+V5S
-
17
GND
-
18
N.C.
-
19
GND
-
20
NC
-
21
NC
-
22
NC
-
CN19 PC Card Connector (68-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
GND
-
2
A_CAD0
I/O
Chapter 5
127
CN19 PC Card Connector (68-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
3
A_CAD1
I/O
4
A_CAD3
I/O
5
A_CAD5
I/O
6
A_CAD7
I/O
7
A_CC/BE0#
I/O
8
A_CAD9
I/O
9
A_CAD11
I/O
10
A_CAD12
I/O
11
A_CAD14
I/O
12
A_CC/BE1#
I/O
13
A_CPAR
I/O
14
A_CPERR#
O
15
A_CGNT#
I
16
A_CINT#
O
17
VCCCB
-
18
AVPP
-
19
A_CCLK1
I
20
A_CIRDY#
O
21
A_CC/BE2#
I/O
22
A_CAD18
I/O
23
A_CAD20
I/O
24
A_CAD21
I/O
25
A_CAD22
I/O
26
A_CAD23
I/O
27
A_CAD24
I/O
28
A_CAD25
I/O
29
A_CAD26
I/O
30
A_CAD27
I/O
31
A_CAD29
I/O
32
A_CRSVD/D2
I/O
33
A_CCLKRUN#
O
34
GND
-
35
GND
-
36
A_CCD1#
I/O
37
A_CAD2
I/O
38
A_CAD4
I/O
39
A_CAD6
I/O
40
A_RSVD/D14
I/O
41
A_CAD8
I/O
42
A_CAD10
I/O
43
A_CVS1#
I/O
44
A_CAD13
I/O
45
A_CAD15
I/O
46
A_CAD16
I/O
47
A_CRSVD/A18
I/O
48
A_CBLOCK#
I/O
49
A_CSTOP#
O
50
A_CDEVSEL#
I/O
51
VCCCB
-
52
AVPP
-
53
A_CTRDY#
I/O
54
A_CFRAME#
I/O
55
A_CAD17
I/O
56
A_CAD19
I/O
57
A_CVS2#
I/O
58
A_CRST#
I
59
A_CSERR#
O
60
A_CREQ#
O
61
A_CC/BE3#
I/O
62
A_CAUDIO
O
63
A_CSTSCHG
I/O
64
A_CAD28
I/O -
65
A_CAD30
I/O
66
A_CAD31
I/O -
67
A_CCD2#
I/O
68
GND
-
CN28 MDC Connector (12-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
GND
-
2
MDC.(3V)
-
3
MC97_3S_SDOUT
O
4
N.C.
-
5
GND
-
6
MDC(3V)
-
7
MC97_3S_SYNC
O
8
GND
-
9
HAD_3S_SDIN1
I
10
GND
-
11
MC97_3S_RST#
O
12
MC97_3S_BITCLK
O
128
Chapter 5
CN18 Internal Microphone Connector (2-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
MIC_INT
I
2
AUDGND
-
CN32/33 Internal Speaker Connector (4-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
SPK_OUT_L-
O
2
SPK_OUT_L+
O
CN24 MINI-PCI connector (124-PIN) (1/2)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
N.C.
-
2
N.C.
-
3
N.C.
-
4
N.C.
-
5
N.C.s
-
6
N.C.
-
7
N.C.
-
8
N.C.
-
9
N.C.
-
10
N.C.
-
11
WIRELESS_LED
O
12
N.C.
-
13
RF_EN
I
14
N.C.
-
15
N.C.
-
16
N.C.
-
17
INTE#
I
18
+5V
-
19
+3V
-
20
INTF#
O
21
N.C.
-
22
N.C.
-
23
GND
-
24
3VSUS
-
25
PCLK_MINI
I
26
PCIRST#
O
27
GND
-
28
+3V
-
29
REQ2#
I
30
GNT2#
O
31
+3V
-
32
GND
-
33
AD31
I/O
34
M_PME#
O
35
AD29
I/O
36
N.C.
-
37
GND
-
38
AD30
I/O
39
AD27
I/O
40
+3V
-
41
AD25
I/O
42
AD28
I/O
43
N.C.
O
44
AD26
I/O
45
CBE3#
I/O
46
AD24
I/O
47
AD23
I/O
48
IDSEL_MP
I/O
49
GND
-
50
GND
-
51
AD21
I/O
52
AD22
I/O
53
AD19
I/O
54
AD20
I/O
55
GND
-
56
PAR
I/O
57
AD17
I/O
58
AD18
I/O
59
CBE2#
I/O
60
AD16
I/O
61
IRDY#
I/O
62
GND
-
63
+3V
-
64
FRAME#
I/O
65
CLKRUN#
I/O
66
TRDY#
I/O
67
SERR#
I
68
STOP#
I/O
69
GND
-
70
+3V
-
Chapter 5
129
CN24 MINI-PCI connector (124-PIN) (1/2)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
71
PERR#
I/O
72
DEVSEL#
I/O
73
CBE1#
I/O
74
GND
-
75
AD14
I/O
76
AD15
I/O
77
GND
-
78
AD13
I/O
79
AD12
I/O
80
AD11
I/O
81
AD10
I/O
82
GND
-
83
GND
-
84
AD9
I/O
85
AD8
I/O
86
CBE0#
I/O
87
AD7
I/O
88
+3V
-
89
+3V
-
90
AD6
I/O
91
AD5
I/O
92
AD4
I/O
93
N.C.
-
94
AD2
I/O
95
AD3
I/O
96
AD0
I/O
97
+5V
-
98
N.C.
-
99
AD1
I/O
100
SERIRQ
I
101
GND
-
102
GND
-
103
N.C.
-
104
N.C.
-
105
N.C.
-
106
N.C.
-
107
N.C.
-
108
N.C.
-
109
N.C.
-
110
N.C.
-
111
N.C.
-
112
N.C.
-
113
GND
-
114
GND
-
115
N.C.
-
116
N.C.
-
117
N.C.
-
118
GND
-
119
GND
-
120
GND
-
121
N.C.
-
122
N.C.
-
123
+5V
-
124
3VSUS
-
JACK4 LineIn Connector (6-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
ANDGND
-
2
LINEIN_L
O
3
LINEIN_R
O
4
LINEIN_JD
O
5
ANDGND
-
6
LINEIN_L
O-
JACK3 External MIC Connector (6-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
ANDGND
-
2
MIC1_L
I
3
MIC1_R
I
4
MIC1_JD
O
5
ANDGND
-
6
MIC1_L
-
CN27 Cardreader Connector-North Star (43-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
1
SD-D2
I/O
23
SD-WP_SM_WPI#
I/O
2
GND
-
24
GND
-
130
Chapter 5
CN27 Cardreader Connector-North Star (43-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
I/O
3
SD-D3
I/O
25
GND
-
4
VCC
-
26
XD-CD#
I/O
5
SD-MS-CLK
I/O
27
XD-R_B#
I/O
6
SD-CMD
I/O
28
XD_RE#
I/O
7
MS-D3_XD_D0
I/O
29
XD_CE#
I/O
8
GND
-
30
XD_CLE
I/O
9
MS-CD#
I/O
31
XD_ALE
I/O
10
MS-D2_XD_D1
I/O
32
XD_WE#
I/O
11
VCC
-
33
XD_WP0#
I/O
12
MS-D0_XD_D2
I/O
34
XGND
-
13
MS-D1_XD_D7
I/O
35
MS_D3_XD_D0
I/O
14
SD-MS_CLK
I/O
36
MS_D2_XD_D1
I/O
15
MS-BS_XD_D3
I/O
37
MS_D0_XD_D2
I/O
16
GND
-
38
MS_BS_XD_D3
I/O
17
GND
-
39
XD_D4
I/O
18
SD-D0
I/O
40
XD_D5
I/O
19
SD-D1
I/O
41
XD_D6
I/O
20
SD-CD#
I/O
42
MS_D1_XD_D7
I/O
21
GND
-
43
VCC
-
22
GND
-
44
CN502 Battery Connector (7-PIN)
PIN No.
Signal name
I/O
PIN No.
Signal name
1
+VPACK
-
2
+VACK
3
BATTERY1_IN
I
4
BAT1_DATA
O
5
BAT1_CLK
O
6
GND
-
7
GND
-
-
-
-
Chapter 5
I/O
131
132
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of the TravelMate 6492.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on
your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the
printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the
local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
Note: To scrap or to return the defective parts, you should follow the local government ordinance or regulations
on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.
For a complete parts list see
Chapter 6
133
TravelMate 6492 Exploded Diagrams
3G Cover Ass’y
Item
Part Name
1
Part Number
Description
6051B0157901
COVER, 3G, PC+ABS
2
3G CARD AL
6053B0230901
SHIELD, 3G COVER, AL+MESH+FR83
3
COVER
SCREW
6052B0012301
SCREW, 1, M2.5, 4mm, M, 4.5mm, 0.8mm, BNI, PATCH, CRING
134
Chapter 6
Battery Ass’y
Item
Part Name
Part Number
Description
1
LABEL
6060B0221401
LABEL, BLANK, REEL, 60mm, 20mm
2
BATTY PACK
6027B0023901
BATTERY PACK, LI - ION, 10.8V, 4100mAH, 3S2P
3
BATTY PACK
6027B0026801
BATTERY PACK, LI - ION, 10.8V, 4700mAH, 2P3S
4
BATTY PACK
BT.00903.004
BATTERY PACK, LI - ION, 11.1V, 7200mAH, 3P3S
Chapter 6
135
BlueTooth Ass’y
Item
Part Name
Part Number
Description
1
LABEL
6060B0238501
LABEL, BLANK, REEL, 40mm, 20mm
2
MODULE
54.AAMVN.004
MODULE, BLUETOOTH, USB 2.0
3
CABLE
6017B0077901
CABLE, ROUND, 8POS, 80mm, 1, BLUETOOTH, 32 AWG
136
Chapter 6
BTCB Case Set Ass’y
Item
Part Name
Part Number
Description
1
BTM CABINET
6051B0157801
CASE, BOTTOM, PC+ABS
2
BTM ODD LATCH
6051B0157501
LATCH, ODD, LOCK, NYLON
3
BTM BATT-LOCK LATCH
6051B0157601
LATCH, BATTERY, RIGHT, NYLON
4
BTM BATTERY KNOB
LOCK
6051B0097401
KNOB, BATTERY, LOCK, PC+ABS
5
BTM BATTERY LATCH
6051B0157301
LATCH, BATTERY, LEFT, NYLON
6
BTM ODD KNOB LOCK
6051B0157401
KNOB, BATTERY, LOCK, PC+ABS
7
BTM BACK BUMPER
6054B0118501
FOOT, BOTTOM, BACK, SILICONE
8
BTM FRONT BUMPER
6054B0195801
FOOT, BOTTOM, FRONT, SILICONE
9
COVERLATCH
6051B0168601
COVER, BATTERY, LATCH, PC+ABS
10
BOTTOM DSUB DOOR
6051B0187001
DOOR, BOTTOM, D-SUB, PC+ABS, RUBBER
11
DOCKING HOOK PLATE
6053B0230501
PLATE, BOTTOM, HOOK, SECC
12
DOCK HOOK
INSULATOR
6054B0149501
INSULATOR, BOTTOM, PP
13
BTM SHIELD L
6053B0231201
SHIELD, BOTTOM, LEFT, SPTE
14
BTM SHIELD R
6053B0231301
SHIELD, BOTTOM, RIGHT, SPTE
15
BTM GASKET BATT
6054B0219101
GASKET, NI/CU PNW FR, 280mm, 17.4mm,
0.13mm
16
BTM GASKET BOSS
6054B0200301
GASKET, NI/CU PNW FR, 50mm, 7mm, 0.13mm
17
BTM GASKET
6054B0219001
GASKET, NI/CU PNW FR, 55mm, 6mm, 0.13mm
18
BTM NET SPKR
6053B0245801
NET, SPEAKER, BOTTOM, MESH 14080+FR83
19
ODD SPRING
6053B0230601
SPRING, CONICAL, 4.5mm, 0.35mm, 19.5mm,
R, SUS 304
20
BATT SPRING
6053B0230701
SPRING, CONICAL, 4.7mm, 0.35mm, 14mm, R,
SUS 304
Chapter 6
137
BTCB Case Set
Item
Part Name
Part Number
Description
1
MN SPEAKER SET
23.TLK0N.002
SPEAKER SET, 40 HM, 2W, 23.5mm,
101X77X20-68X
6052B0078001
SCREW, 1, M2.5, 6.0mm, M, 4.5mm, 0.8mm,
BNI, PATCH
6060A0086501
LABEL, BLANK-050-25X11
1510B0303301
ASSEMBLY, CASE, BOTTOM, OFFLINE
2
3
4
138
BTCB CASE SET
Chapter 6
CPU Ass’y
Item
Part Name
Part Number
Description
1
CPU
KC.71001.DTP
CPU, 1.8GHz, 800MHz, 2M, MICRO FCPGA,
478P, TRAY
2
CPU
KC.73001.DTP
CPU, 2.0GHz, 800MHz, 4M, MICRO FCPGA,
478P, TRAY
3
CPU
KC.75001.DTP
CPU, 2.2GHz, 800MHz, 2M, MICRO FCPGA,
478P, TRAY
4
CPU
KC.77001.DTP
CPU, 2.4GHz, 800MHz, 2M, MICRO FCPGA,
478P, TRAY
Chapter 6
139
CTO Cover Set Ass’y
Item
Part Name
Part Number
Description
1
BTM CTO COVER
6051B0157701
COVER, CTO, PC+ABS
2
BTM FRONT
BUMPER
6054B0195801
FOOT, BOTTOM, FRONT, SILICONE
3
HDD DASP
RUBBER
6054B0149701
BUMPER, HDD, COVER, NBR
4
CTO COVER
SHIELD
6053B0231001
SHIELD, CTO, COVER, AL+MESH+FR83
5
COVER SCREW
6052B0012301
SCREW, 1, M2.5, 4mm, M, 4.5mm, 0.8mm, BNI,
PATCH, C-RING
6
CTO GASKET
THERMAL
6054B0220201
GASKET NI/CU PNW FOF 30mm, 10mm, 1.5mm
7
CTO GASKET HDD
6054B0220301
GASKET NI/CU PNW FOF 20mm, 10mm, 4mm
140
Chapter 6
Display Ass’y
Item
Part Name
Part Number
Description
1
DISPLAY BEZEL
ASSEMBLY
1510B0298501
ASSEMBLY, BEZEL, DISPLAY, OFFLINE
2
SCREW 125040M
6052A00346XX
SCREW - 125040M (4.5DX0.8T) - XX - PATCH
3
SCREW 125020M
86.D03VN.002
SCREW - 125050M (4.5D*0.8T) - BK - PATCH
4
INSULATOR DISPLAY
6054B0185301
INSULATOR, DISPLAY, FR700
5
DISP RUBBER CORNER
47.TLK0N.002
BUMPER, DISPLAY, CORNER, SILICONE
6
SCREW 120030M
605200078405
SCREW - 120030M (4.5D*0.8T) - NIH - PATCH
7
DISP-WC HINGE/W
BRACKET - R
33.TLK0N.003
HINGE-W BRACKET, DISPLAY, RIGHT, 5.5~6.5
KGF-CM
8
CHICONY - CNF6122
6047B0002501
CAMERA, MODULE, LENS, 0.3M
9
DISPLAY REAR
ASSEMBLY
1510B0298401
ASSEMBLY, CASE, REAR, DISPLAY, OFFLINE
10
INSULATOR INVERTER
47.TLK0N.001
INSULATOR, INVERTER, FORMEX, GK-5BK
11
DISPLAY INVERTER
19.TCX0N.001
INVERTER, 5VDC, AC690V, 55KHz, 130X12.5
12
MYLAR DISPLAY
6054B0191201
INSULATOR, DISPLAY, PC FR-700
6060B0221401
LABEL, BLANK, REEL, 60mm, 20mm
13
14
DISP-WC HINGE/W
BRACKET - L
33.TLK0N.002
HINGE-W BRACKET, DISPLAY, LEFT, 5.5~6.5
KGF-CM
15
LCM 14.1”
6024B0017801
LCM, 14.1, TFT, WXGA, LVDS, 415g
16
LCM 14.1”
LK.14105.019
LCM, 14.1, TFT, WXGA, LVDS, 400g
Chapter 6
141
Item
Part Name
Part Number
Description
17
LCM 14.1”
LK.14106.011
LCM, 14.1, TFT, WXGA, LVDS, 390g
18
LCM 14.1”
LK.14105.018
LCM, 14.1, TFT, WXGA, LVDS, 400g
19
LCM CABLE
6017B0108901
CABLE, FLAT, 40POS, 231.16mm, 1, LCM
20
LCM CABLE
6017B0108801
CABLE, FLAT, 40POS, 231.16mm, 1, LCM
142
Chapter 6
Display Bezel Ass’y
Item
Part Name
Part Number
Description
1
DISP BEZEL
6051B0154501
CASE, DISPLAY, BEZEL, PC+ABS, PRINT
2
DISP CCD
BEZEL_NAMEPLATE -30
6053B0215001
NAME PLATE, CCD (0.3), AL
3
DISP RUBBER TOPMIDDLE
47.TLK0N.004
BUMPER, DISPLAY, TOP-MIDDLE, SILICONE
4
DISP CCD LENS
6051B0154401
LENS, CCD, PC
5
DISP BEZEL SHIELD
6053B0273301
SHIELD, DISPLAY BEZEL, AL FOIL
6
MAGNET 63DX35T
6053B0245001
MAGNET, DISPLAY, ROUND, 6.3mm, 3.5mm, NI
7
DISP WC BEZEL_LOGO
6053B0132001
NAME PLATE, ACER, 24.4mm, 7.1mm, 0.6mm, AL
8
DISP - WC RUBBER
47.TLK0N.003
BUMPER, DISPLAY, SILICONE
Chapter 6
143
Display Rear Ass’y
Item
Part Name
Part Number
Description
1
DISPLAY REAR_MG_AL
6053B0214701
CASE, DISPLAY, REAR, MG_AL, COATING
2
DISP ANTENNA COVER
6051B0154101
COVER, DISPLAY, ANTENNA, PC+ABS, COAT,
PRINT
3
DISP LATCH SPRING
6053B0214501
SPRING, TENSION, DISPLAY, SUS304
4
ANTENNA WLAN L
6036B0014401
ANTENNA, DUAL, 2.4/5.2G, 550/550mm, 1.37mm
5
DISP LATCH
6051B0154201
LATCH, DISPLAY, NYLON
6
CCD MYLAR
6054B0245101
INSULATOR, CCD, LUMIRROR X30
7
DISP KNOB
6051B0158301
KNOB, DISPLAY, PC+ABS
8
MIC SET R
23.TLK0N.003
MIC. SET, -44dB, 7.2X3, OMNI, 680mm
9
ANTENNA MIMO R
6036B0016901
ANTENNA, DUAL, 2.4/5.2G, 550mm, 1.37mm
10
SCREW 120030M
86.TLK0N.004
SCREW - 120030M (4.5*0.8T) - BNI - PATCH
11
MYLAR MICROPHONE
6054B0211601
INSULATOR, MIC, PC (FR-83)
12
DISP WC REAR-LOGO
6053B0132501
NAMEPLATE, ACER, 44.2mm, 11.2mm, 0.9mm,
AL
144
Chapter 6
HDD Ass’y
Item
Part Name
Part Number
Description
1
LABEL
6060B0221401
LABEL, BLANK, REEL, 60mm, 20mm
2
INSULATOR
6054B0218901
INSULATOR, HDD, LUMIRROR S10 - AL
3
FRAME
6051B0168501
FRAME, HDD, PC+SILICONE
4
CONNECTOR
20.TLK0N.001
CONNECTOR, HDD, SATA, FL, BLK, 1X22, 90D,
DIP, T
5
HDD, 60G
6022B0036501
HDD, SATA, 60GB, 5.4KRPM, 22P, 11ms, 5.5ms,
SATA
6
HDD, 80G
KH.08007.021
HDD, SATA, 80GB, 5.4KRPM, 22P, 11ms, 5.5ms,
SATA
7
HDD, 120G
KH.12007.010
HDD, SATA, 120GB, 5.4KRPM, 22P, 11ms, 5.5ms,
SATA
8
HDD, 160G
KH.16007.011
HDD, SATA, 160GB, 5.4KRPM, 22P, 12ms, 5.5ms,
SATA
Chapter 6
145
Keyboard Ass’y
Item
Part Name
Part Number
Description
1
LABEL
6060B0221401
LABEL, BLANK, REEL, 60mm, 20mm
2
KEYB ACER MN
6037B0015201
KEYBOARD/W ST, 88, 24P, BLACK, US-INTL,
310X115.52, 5.5mm
146
Chapter 6
Memory Ass’y
Item
Part Name
Part Number
Description
1
LABEL
6060B0221401
LABEL, BLANK, REEL, 60MM, 20MM
2
MEMORY
MODULE
6021B0060901
MEMORY MODULE, 512MB, PC2 - 4200, DDR2, 200P, 6
3
MEMORY
MODULE
6021B0064701
MEMORY MODULE, 1GB, PC2 - 4200, DDR2, 200P, 128
4
MEMORY
MODULE
KN.5120G.019
MEMORY MODULE, 512MB, PC2 - 5300, DDR2, 200P, 6
5
MEMORY
MODULE
KN.1GB0G.006
MEMORY MODULE, 1GB, PC2 - 5300, DDR2, 200P, 128
Chapter 6
147
Modem Ass’y
Item
Part Name
Part Number
Description
1
LABEL
6060B0238501
LABEL, BLANK, REEL, 40mm, 20mm
2
MODEM
FX.22500.004
MODEM, MDC, 56K, AZALIA
148
Chapter 6
ODD Ass’y
Item
Part Name
1
Part Number
Description
1310A2129601
ASSEMBLY, BOARD, MULTI-ODD
2
ODD HOLDERMODULE
42.TCXVN.006
HOLDER, ODD, PC+ABS
3
SCREW 120050M
86.TCXVN.004
SCREW - 120050M (4.5DX0.5T) - BK - PATCH
4
SCREW
86.TCXVN.006
SCREW - 1 - M2. 0-3. 0-M-4. 0DX0. 3T - BK - PATCH
5
LABEL
6060B0021401
LABEL, BLANK, REEL, 60MM, 20MM
6
1510B0224401
ASSEMBLY, BEZEL, ODD, OFFLINE
7
1510B0224501
ASSEMBLY, BEZEL, ODD, OFFLINE
8
DVD
KO.0240D.005
DVD, COMBO, 8X, 24X, 24X, 24X, M2,
128X12.7X126.1MM, SLM
9
DVD
KU.0080D.027
DVD, SUPER MULTI, 5X, 8X, 6X, 8X, 8X, 8X, 24X, 16
Chapter 6
149
Switch Cover Set Ass’y
Item
Part Name
Part Number
Description
1
SWICTH COVER
6051B0154901
COVER, TOP CASE, PC+ABS
2
SWITCH COVER
PLATE
6054-B01863-0
NAME PLATE, FUNCTION KEY, PC, TOP CASE
3
FUNCTION BUTTON
6051B0155401
BUTTON, TOP CASE, FUNCTION, PC, COAT
4
POWER BUTTON
6051B0155201
BUTTON, TOP CASE, POWER, PC, COAT
5
CAPS LOCK LENS
6054B0185701
INSULATOR, SWITCH COVER, CAPS LOCK, PC
150
Chapter 6
Touchpad Bracket Set Ass’y
Item
Part Name
Part Number
Description
1
THPAD BRACKET
6053B0225701
BRACKET, TOP, TOUCH PAD, SECC
2
THPAD MYLAR
6054B0185601
INSULATOR, TOP, TOUCH PAD, LUMIRROR X30
3
TOP GASKET
AUDIO
6054B0220501
GASKET, NI/CU PNW FR, 28mm, 9.5mm, 0.13mm
Chapter 6
151
TPCB CaseSet Ass’y
Item
Part Name
Part Number
Description
1
TOP CABINET
605180155001
CASE, TOP, PC +ABS, COAT
2
IR LENS
605180155101
LENS, TOP, IR, PC
3
CHARGER LENS
605180155301
LENS, TOP, CHARGE, PC
4
3G LENS
605180155501
LENS, TOP, 3G, PC
5
R STICK POINT BUTTON
605180155601
BUTTON, TOP, FINGERPRINT R,
PC+ABS, COAT+PRINT
6
BT & WL LENS
605180155701
LENS, TOP, BT, WIRELESS, PC
7
BT & WL KNOB
605180155801
KNOB, BT, WIRELESS, PC, BLACK
8
CARD READER DOOR
605180155901
DOOR, TOP, CARDREADER,
PC+ABS+RUBBER
9
PICK BUTTON
605180156001
BUTTON, PICK BUTTON, TOUCH PAD,
PC+ABS, COAT
152
Chapter 6
Item
Part Name
Part Number
Description
10
4 WAY BUTTON
605180156101
BUTTON, 4 WAY, TOUCH PAD, PC+ABS,
COAT
11
THPAD FRAME
605180156201
FRAME, TOUCH PAD, PC+ ABS, COAT
12
3G FRONT BEZEL
605180156301
LENS, TOP, 3G, PC
13
FRONT BEZEL
605180156401
BEZEL, TOP CASE, FRONT, PC+ABS,
PRINT/BLACK
14
L STICK POINT BUTTON
605180159201
BUTTON, TOP, FINGER PRINT L,
PC+ABS, COAT+PRINT
15
MYLAR
605180181001
INSULATOR, LATCH HOLE, PP
16
TOP NO FGPT R STICK POINT
BUTTON
605180181601
BUTTON, TOP, NO FGPT R, PC+ABS,
COAT+PRINT
17
TOP NO FGPT L STICK POINT
BUTTON
605180181701
BUTTON, TOP, NO FGPT L, PC+ABS,
COAT+PRINT
18
TOP THPAD FRAME STANDARD
605180181801
FRAME, TOUCH PAD, NO FGPT,
PC+ABS, COAT
19
R BRACKET
605380215401
BRACKET, TOP,RIGHT, AL
20
L BRACKET
605380215501
BRACKET, TOP, LEFT, AL
21
SMART CARD BRACKET
605380225601
BRACKET, SMART CARD, SPCC
22
TOP SMART CARD DUMMY
605380225601
DUMMY, SMART CARD, PC+ABS
23
TOP SHIELD FOIL PALMREST R
605380244101
SHIELD, TOP PALMREST, RIGHT, AL
FOIL
24
TOP ODD BRACKET
605380244201
BRACKET, TOP, ODD, AL5052
25
TOP SHIELD FOIL L
605380244301
SHIELD, TOP, LEFT, AL FOIL
26
TOP SHIELD FOIL M
605380244401
SHIELD, TOP, MIDDLE, AL FOIL
27
TOP SHIELD FOIL R
605380244501
SHIELD, TOP, RIGHT, AL FOIL
28
TOP SHIELD FOIL PALMREST L
605380244601
SHIELD, TOP, PALMREST, LEFT, AL FOIL
29
TOP SHIELD METAL PALMREST
L
605380245101
SHIELD, TOP, METAL, LEFT, SPTE
30
TOP SHIELD METAL PALMREST
R
605380245201
SHIELD, TOP, METAL, RIGHT, SPTE
31
GASKET_15X5X0.5
605380107001
GASKET, NI/CU PNW FOF, 15.0mm,
5.0mm, 0.5mm
32
W: 5mm x H: 4mm x L: 15mm
605380107301
GASKET, NI/CU PNW FOF, 15.0mm,
5.0mm, 4.0mm
33
MN_TOP_RUBBER_HINGE
605380193401
BUMPER, TOP, HINGE, SILICONE
Chapter 6
153
Wireless Ass’y
Item
Part Name
Part Number
1
LABEL
6060B0238501
LABEL, BLANK, REEL, 40MM, 20MM
2
SCREW
86.TLK0N.003
SCREW, 1, M2.5, 3.5MM, M, 4.5MM, 0.8MM, BK,
PATCH
3
MODULE
KI.KDN01.001
MODULE, WIRELESS LAN, MINI PCI 802.11A/G/N
4
MODULE
KI.KDN01.002
MODULE, WIRELESS LAN, MINI PCI 802.11A/G/N
5
MODULE
KI.KDN01.003
MODULE, WIRELESS LAN, MINI PCI 802.11A/G/N
6
MODULE
KI.KDN01.006
MODULE, WIRELESS LAN, MINI PCI 802.11A/G/N
7
MODULE
KI.KDN01.007
MODULE, WIRELESS LAN, MINI PCI 802.11A/G
8
MODULE
KI.KDN01.008
MODULE, WIRELESS LAN, MINI PCI-802.11A/G
9
MODULE
KI.GLN01.001
MODULE, WIRELESS LAN, PCI EXP 802.11A/G
10
MODULE
KI.GLN01.003
MODULE, WIRELESS LAN, PCI EXP 802.11B/G
11
MODULE
KI.GLN01.005
MODULE, WIRELESS LAN, PCI EXP 802.11B/G
12
MODULE
KI.GLN01.002
MODULE, WIRELESS LAN, PCI EXP 802.11A/G
154
Description
Chapter 6
Parts List
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
ADAPTER
ADAPTER 65W 3PINS LITEON PA-165002IR YELLOW 1.7X5.5X11 LF
ADAPTOR,3PIN,65W,19VDC,3.42A,2
40VAC
AP.06503.014
ADAPTER
ADAPTER 65W 3PINS LISHIN
SLS0335A19A54LF YELLOW,
1.7X5.5X11
ADAPTOR,3PIN,65W,19VDC,3.42A,2
40VAC
AP.06506.003
ADAPTER
ADAPTER 65W 3PINS DELTA SADP65KB DFA YELLOW 1.7X5.5X11 LF
ADAPTOR,3PIN,65W,19VDC,3.42A,1
00V~240V
AP.06501.013
ADAPTER
ADAPTER 65W 3PINS LITEON PA-165002AC 1.7X5.5X11 LF
ADAPTOR,3PIN,65W,19VDC,3.42A,1
00-240VAC
AP.06503.016
BATTERY
BATTERY LI-ION 6CELL SANYO 3S2P
3800MAH
BATTERY PACK,LIION,11.1V,3800mAH,2P3S
BT.00603.026
BATTERY
BATTERY LI-ION 6CELL SANYO
TM2007-A 3S2P 4000MAH
BATTERY PACK,LIION,11.1V,4000mAH,3S2P
BT.00603.039
BATTERY
BATTERY LI-ION 6CELL SONY TM2007A 3S2P 4000MAH
BATTERY PACK,LIION,11.1V,4000mAH,2P3S
BT.00604.017
BATTERY
BATTERY LI-MN 6CELL SIMPLO 3S2P
4000MAH
BATTERY PACK,LIION,10.8V,4000mAH,3S2P
BT.00607.003
BATTERY
BATTERY LI-ION 6CELL SANYO
TM2007-A 3S2P 4800MAH
BATTERY PACK,LIION,11.1V,4800mAH,3S2P
BT.00603.040
BATTERY
BATTERY LI-ION 6CELL SONY 3S2P
4800MAH
BATTERY PACK,LIION,11.1V,4000mAH,3S2P
BT.00604.005
BATTERY
BATTERY LI-ION 6CELL SIMPLO
TM2007-A 3S2P 4800MAH
BATTERY PACK,LIION,10.8V,4800mAH,3S2P
BT.00607.009
BATTERY
BATTERY LI-ION 9CELL 2.4 SANYO
7200MAH
BATTERY PACK,LIION,11.1V,7200mAH,3P3S
BT.00903.004
BATTERY
BATTERY LI-ION 9CELL SONY TM2007A 3S3P 7200MAH
BATTERY PACK,LIION,11.1V,4800mAH,3S2P
BT.00904.003
BATTERY
BATTERY LI-ION 9CELL SIMPLO
TM2007-B 3S3P 7200MAH
BATTERY PACK,LIION,10.8V,7200mAH,3P3S
BT.00907.003
BOARD
BLUETOOTH BOARD FOXCONN
T60H928.01
MODULE,BLUE TOOTH,USB2.0
54.AAMVN.00
4
BOARD
MODEM BOARD 1.5 FOXCONN
T60M951.04 (AGERE 3.3V)
MODEM,MDC,56K,AZALIA
FX.22500.004
BOARD
MODEM BOARD 1.5 FOXCONN
T60M951.10 (AGERE 3.3V) FOR
AUSTRALIA ONLY
MODEM,MDC,56K,AZALIA
FX.22500.014
BOARD
WIRELESS LAN BOARD 802.11ABG
INTEL 3945ABG MOW1
MODULE,WIRELESS LAN,PCI EXP
802.11A/G
KI.GLN01.001
BOARD
WIRELESS LAN BOARD 802.11ABG
INTEL 3945ABG MOW2
MODULE,WIRELESS LAN,PCI EXP
802.11A/G
KI.GLN01.002
BOARD
WIRELESS LAN BOARD 802.11ABG
INTEL 3945ABG ROW
MODULE,WIRELESS LAN,PCI EXP
802.11B/G
KI.GLN01.003
BOARD
WIRELESS LAN BOARD 802.11ABG
INTEL 3945ABG JP
MODULE,WIRELESS LAN,PCI EXP
802.11A/G
KI.GLN01.004
BOARD
WIRELESS LAN BOARD 802.11BG
INTEL 3945BG
MODULE,WIRELESS LAN,PCI EXP
802.11B/G
KI.GLN01.005
BOARD
WIRELESS LAN BOARD 802.11AGN
INTEL 4965AGN MOW1 MINI PCI
MODULE,WIRELESS LAN,MINI PCI
802.11A/G/N
KI.KDN01.001
Chapter 6
155
156
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
BOARD
WIRELESS LAN BOARD 802.11AGN
INTEL 4965AGN MOW2 MINI PCI
MODULE,WIRELESS LAN,MINI PCI
802.11A/G/N
KI.KDN01.002
BOARD
WIRELESS LAN BOARD 802.11AGN
INTEL 4965AGN ROW MINI PCI
MODULE,WIRELESS LAN,MINI PCI
802.11A/G/N
KI.KDN01.003
BOARD
WIRELESS LAN BOARD 802.11AG
INTEL 4965AG MOW1 MINI PCI
MODULE,WIRELESS LAN,MINI PCI
802.11A/G/N
KI.KDN01.006
BOARD
WIRELESS LAN BOARD 802.11ABG
INTEL 4965AG MOW2 MINI PCI
MODULE,WIRELESS LAN,MINI PCI
802.11A/G
KI.KDN01.007
BOARD
WIRELESS LAN BOARD 802.11AG
INTEL 4965AG ROW MINI PCI
MODULE,WIRELESS LAN,MINI PCI802.11A/G
KI.KDN01.008
BOARD
TOUCHPAD SYNAPTICS
TM61PUF1R544
TOUCH PAD,NO
BUTTON,12P,67X40,BLK
56.TLK0N.001
BOARD
HOTKEY BOARD
FRU,I/O BOARD
ASSEMBLY,HOTKEY BOARD
55.TLK0N.001
BOARD
TOUCHPAD BUTTON BOARD
FRU,I/O BOARD ASSEMBLY,TOUCH
PAD BUTTON BOARD
55.TLK0N.004
BOARD
STICK POINT BOARD W/O FINGER
PRINTER
FRU,I/O BOARD ASSEMBLY,STICK
POINT/B W/O FINGER PRINT CHIP
55.TLL0N.001
BOARD
I/O BOARD
FRU,I/O BOARD ASSEMBLY,W/O 3G
CN
55.TLK0N.002
BOARD
ROBSON BOARD
FRU,I/O BOARD
ASSEMBLY,ROBSON BOARD
55.TLK0N.003
CABLE
POWER CORD 3PIN USA
CORD-ROUND-3POS-1828mm-EPOWER-USA
27.AAMVN.00
1
CABLE
POWER CORD 3PIN EUR
CORD-ROUND-3POS-1850mm-EPOWER-EUR
27.AAMVN.00
2
CABLE
POWER CORD 3PIN SOUTH AFRICA
CORD,ROUND,3POS,1800mm,E,SO
UTH AFRICA
27.AAMVN.00
8
CABLE
POWER CORD 3PIN DENMARK
CORD,ROUND,3POS,1800mm,E,DA
NISH
27.AAMVN.01
0
CABLE
POWER CORD ISRAEL
CORD,ROUND,3POS,1800mm,E,ISR 27.AAMVN.01
AEL
1
CABLE
POWER CORD 3PIN ITALIAN
CORD,ROUND,3POS,1800mm,E,ITL
27.AAMVN.00
9
CABLE
POWER CORD 3PIN UK
CORD-ROUND-3POS-1828mm-EPOWER-UK
27.AAMVN.00
4
CABLE
POWER CORD 3PIN SWISS
CORD,ROUND,3POS,1830mm,E,PO
WER, SWITZERLAND
27.AAMVN.00
6
CABLE
POWER CORD AUSTRALIA W/LABEL
CORD-ROUND-3POS-1850mm-EPOWER-AUL
27.AAMVN.00
3
CABLE
POWER CORD 3PIN CHINA
CORD,ROUND,3POS,1800mm,E,PO
WER,PRC
27.AAMVN.00
5
CABLE
POWER CORD SOUTH AFRICA (AIL)
CORD,ROUND,3POS,1830mm,E,PO
WER,S. AFRICAN
27.AAMVN.00
7
CABLE
MODEM CABLE W/ 3 CONNECTORS
CABLE,ROUND,2POS,166mm,I,RJ11 50.TLK0N.001
CABLE
CABLE FROM TOUCHPAD BUTTON
BOARD TO TOUCHPAD
FFC,12P,1L,1.575X0.256X0.004,PET,
S
CABLE
CABLE FROM TOUCHPAD BUTTON
BOARD TO STICK POINT BOARD
FFC,8P,1L,2.756X0.177X0.004,PET,S 50.TLK0N.004
CABLE
CABLE FROM STICK POINT BOARD TO
MAINBOARD
FFC,12P,1L,3.465X0.256X0.004,PET,
S
50.TLK0N.003
50.TLK0N.005
Chapter 6
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
CABLE
HOTKEY BOARD CABLE
FFC,14P,1L,5.787X0.295X0.004,PET,
S
50.TLK0N.002
CABLE
BLUETOOTH CABLE
CABLE,ROUND,8POS,80mm,I,BLUE
TOOTH
50.TLK0N.008
CASE/COVER/
BRACKET
ASSEMBLY
TOUCHPAD BRACKET
SET,BRACKET,TOUCHPAD
33.TLK0N.001
CASE/COVER/
BRACKET
ASSEMBLY
LOWER CASE
FRU,BOTTOM CASE ASSEMBLY
60.TLK0N.001
CASE/COVER/
BRACKET
ASSEMBLY
UPPER CASE W/O FINGER PRINTER
HOLE
FRU,TOP CASE ASSEMBLY
60.TLL0N.001
CASE/COVER/
BRACKET
ASSEMBLY
MIDDLE COVER
SET,COVER,SWITCH
42.TLK0N.001
CASE/COVER/
BRACKET
ASSEMBLY
UNILOAD COVER
SET,COVER,CTO
42.TLK0N.002
CASE/COVER/
BRACKET
ASSEMBLY
3G COVER
SET,COVER,3G
42.TLK0N.003
CASE/COVER/
BRACKET
ASSEMBLY
PCMCIA DUMMY CARD
DUMMY,CARDBUS,PC+ABS
42.TLK0N.004
CASE/COVER/
BRACKET
ASSEMBLY
MINI DUMMY CARD
DUMMY,EXPRESS CARD,PC+ABS
42.TLK0N.005
CASE/COVER/
BRACKET
ASSEMBLY
SMART CARD READER WITH CABLE
E.SET,FFC+CONN,10P,57.55MM
60.TLK0N.003
CASE/COVER/
BRACKET
ASSEMBLY
CONNECTOR 2ND HDD
E.SET,FPC+CONN,50P/
20P,38.06MM
22.D03VN.00
1
CASE/COVER/
BRACKET
ASSEMBLY
BRACKET 2ND HDD
BRACKET,HDD,BOTTOM,SECC
33.D03VN.00
2
CASE/COVER/
BRACKET
ASSEMBLY
UPPER CASE 2ND HDD
CASE,HDD,BOTTOM,PC+ABS
60.D03VN.00
3
CASE/COVER/
BRACKET
ASSEMBLY
LOWER CASE 2ND HDD
CASE,HDD,TOP,PC+ABS
60.D03VN.00
4
SCREW
SCREW
SCREW,I,M2.5,5mm,M,0.45mm,0.8m
m,BNI,PATC
86.D03VN.00
4
SCREW
SCREW
SCREW-WI30030M(5.0Dx1.5T)-NIHARDEN
86.AAMVN.00
1
FAN
FAN
FAN.SET,VERTICAL,5V,0.33A,3600R
PM,94.9X80.2X18.9, 30mm,Y
23.TLK0N.001
Chapter 6
157
158
DESCRIPTON
ACER PART
NO.
CATEGORY
PARTNAME
HEATSINK
CPU HEATSINK
THERMAL MODULE,CPU
60.TLK0N.004
CASE/COVER/
BRACKET
ASSEMBLY
CPU HEATSINK FINGER
FINGER,CPU,SUS 301
33.TLK0N.004
CPU/
PROCESSOR
CPU INTEL CORE2DUAL T7100 PGA
1.8G 2M 800
CPU,1.8G,800MHZ,2M,MICRO
FCPGA,478P,TRAY
KC.71001.DT
P
CPU/
PROCESSOR
CPU INTEL CORE2DUAL T7300 PGA
2.0G 4M FSB800
CPU,2.0G,800MHZ,4M,MICRO
FCBGA,478P,TAP
KC.73001.DT
P
CPU/
PROCESSOR
CPU INTEL CORE2DUAL T7500 PGA
2.2G 4M FSB800
CPU,2.2GHZ,800MHZ,4M,MICRO
FCBGA,478P,TAP
KC.75001.DT
P
CPU/
PROCESSOR
CPU INTEL CORE2DUAL T7700 PGA
2.4G 4M FSB800
CPU,2.4G,800MHZ,4M,MICRO
FCPGA,478P,TRAY
KC.77001.DT
P
COMBO
MODULE
CDRW/DVD COMBO MODULE 24X
BOARD
ODD BOARD
FRU,I/O BOARD ASSEMBLY,ODD
MULTI INTERFACE
55.TLK0N.006
CASE/COVER/
BRACKET
ASSEMBLY
OPTICAL RAIL HOLDER
HOLDER,ODD,PC+ABS
42.TCXVN.00
6
CASE/COVER/
BRACKET
ASSEMBLY
COMBO BEZEL GBASE
SET,BEZEL,ODD
42.TCXVN.00
5
COMBO
MODULE
CDRW/DVD COMBO DRIVE 24X HLDS
GCC-T10N LF W/O BEZEL
DVD,COMBO,8X,24X,24X,24X,M2,12 KO.0240D.00
8X12.7X126.1mm,SLIM
5
COMBO
MODULE
CDRW/DVD COMBO DRIVE 24X SONY
CRX880A LF W/O BEZEL
DVD,COMBO,8X,24X,24X,24X,GRE
EN,M2,128X12.7X126.1mm
DVD RW DRIVE
DVD-RW SUPER MULTI MODULE 8X
BOARD
ODD BOARD
FRU,I/O BOARD ASSEMBLY,ODD
MULTI INTERFACE
55.TLK0N.006
CASE/COVER/
BRACKET
ASSEMBLY
OPTICAL RAIL HOLDER
HOLDER,ODD,PC+ABS
42.TCXVN.00
6
CASE/COVER/
BRACKET
ASSEMBLY
SUPER MULTI BEZEL GBASE
SET,BEZEL,ODD
42.TCXVN.00
7
DVD RW DRIVE
KU.0080D.02
DVD-RW DRIVE 8X SUPER MULTI
DVD,SUPER
GBASE HLDS GSA-T20N LF W/O BEZEL MULTI,5X,8X,6X,8X,8X,8X,24X,16X,2 7
4X,M2, 128X12.7X126.1mm,SLIM
DVD RW DRIVE
DVD-RW DRIVE 8X SUPER MULTI
GBASE PHILIPS DS-8A1P LF W/O
BEZEL
KU.00809.010
DVD,SUPER
MULTI,5X,8X,6X,8X,8X,8X,24X,24X,2
4X,M2, 128X12.7X126.1mm,SLIM
DVD RW DRIVE
DVD-RW DRIVE 8X SUPER MULTI
GBASE TOSHIBA TS-L632D LF W/O
BEZEL F/W:AC01
DVD,SUPER
KU.00801.018
MULTI,5X,8X,6X,8X,8X,8X,24X,24X,2
4X,
GREEN,128X12.7X126.1mm,SLIM
HDD/HARD DISK
DRIVER
HDD 80GB 5400RPM SATA HGST
HTS541680J9SA00 SURUGA-B LF F/W:
C70P
6M.TLK0N.00
1
KO.0240E.00
5
6M.TLK0N.00
2
KH.08007.021
HDD,SATA,80GB,5.4KRPM,22P,11ms
,5.5ms,SATA1.0 ,2.5X 0.37,M3
Chapter 6
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
HDD/HARD DISK
DRIVER
HDD 80GB 5400RPM SATA SEAGATE
ST980811AS(9S1132-190) VENUS LF F/
W:3.ALD
HDD,SATA,80GB,5.4KRPM,22P,12.5
ms,5.6ms,SATA 2.0, 2.5X0.37
KH.08001.030
HDD/HARD DISK
DRIVER
HDD 80GB 5400RPM SATA TOSHIBA
MK8037GSX GEMINI BS LF F/W:DL230J
HDD,SATA,80GB,5.4KRPM,22P,12m
s,5.6ms,SATA 2.0,2.5X0.37,M3
KH.08004.010
HDD/HARD DISK
DRIVER
HDD 80GB 5400RPM SATA WD
WD800BEVS-22RST0 ML80 LF F/
W:04.01G04
HDD,SATA,80GB,5.4KRPM,22P,12m
s,5.5ms,SATA1.0,2.5X0.37,M3
KH.08008.033
HDD/HARD DISK
DRIVER
HDD 120GB 5400RPM SATA HGST
HTS541612J9SA00 SURUGA-B LF F/
W:C70P
HDD,SATA,120GB,5.4KRPM,22P,11m KH.12007.010
s,5.5ms,SATA1.0, 2.5X0.37,M3
HDD/HARD DISK
DRIVER
HDD 120GB SATA 5400RPM SEAGATE
ST9120822AS VENUS LF F/W:3.ALD
HDD,SATA,120GB,5.4KRPM,22P,12.
5ms,5.6ms,SATA 2.0, 2.5X0.37
KH.12001.031
HDD/HARD DISK
DRIVER
HDD 120GB 5400RPM SATA TOSHIBA
MK1237GSX GEMINI BS LF F/W:DL130J
HDD,SATA,120GB,5.4KRPM,22P,12
ms,5.6ms,SATA 2.0, 2.5X0.37,M3
KH.12004.006
HDD/HARD DISK
DRIVER
HDD 120GB 5400RPM SATA WD
WD1200BEVS-22RST0 ML80 LF
HDD,SATA,120GB,5.4KRPM,22P,12
ms,5.5ms,SATA1.0, 2.5X0.37,M3
KH.12008.018
HDD/HARD DISK
DRIVER
HDD 160GB 5400RPM SATA HITACHI
HTS541616J9SA00 SURUGA-B LF F/
W:C70P
HDD,SATA,160GB,5.4KRPM,22P,12
ms,5.5ms,SATA1.0, 2.5X0.37,M3
KH.16007.011
HDD/HARD DISK
DRIVER
HDD 160GB 5400RPM SATA SEAGATE
ST9160821AS VENUS LF FW: 3.ALD
HDD,SATA,160GB,5.4KRPM,22P,12.
5ms,5.5ms,SATA II,2.5X0.37,M3
KH.16001.026
HDD/HARD DISK
DRIVER
HDD 160GB 5400RPM SATA TOSHIBA
HDD,SATA,160GB,5.4KRPM,22P,12
MK1637GSX GEMINI BS LF F/W: DL030J ms,5.6ms,SATA 2.0, 2.5X0.37,M3
KH.16004.001
HDD/HARD DISK
DRIVER
HDD 160GB 5400RPM SATA WD
WD1600BEVS-22RST0 ML80 LF
HDD,SATA,160GB,5.4KRPM,22P,12
ms,5.5ms,SATA1.0, 2.5X0.37,M3
KH.16008.019
CASE/COVER/
BRACKET
ASSEMBLY
HDD CONNECTOR
CONNECTOR,HDD,SATA,FL,BLK,1X
22,90D,SMD,TR
20.TLK0N.001
CASE/COVER/
BRACKET
ASSEMBLY
HDD HOLDER
BRACKET,HDD,SECC
42.TLK0N.006
CASE/COVER/
BRACKET
ASSEMBLY
HDD INSULATOR
INSULATOR,HDD,LUMIRROR
S10+AL
42.AAMVN.00
5
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK US INTERNATIONAL
KEYBOARD/W
KB.INT00.070
ST,88,24P,BLACK,INTL,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK US INTERNATIONAL HEBREW
KEYBOARD/W
ST,88,24P,BLACK,ISR,310X115.52,5.
5mm
KB.INT00.071
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK UK
KEYBOARD/W
ST,89,24P,BLACK,UK,310X115.52,5.
5mm
KB.INT00.072
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK TURKISH
KEYBOARD/W
ST,89,24P,BLACK,TUR,310X115.52,5
.5mm
KB.INT00.073
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK THAILAND
KEYBOARD/W
ST,88,24P,BLACK,THAI,310X115.52,
5.5mm
KB.INT00.074
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK SWISS/G
KEYBOARD/W
ST,89,24P,BLACK,SWISS,310X115.5
2, 5.5mm
KB.INT00.075
Chapter 6
159
160
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK SWEDISH
KEYBOARD/W
ST,89,24P,BLACK,SWE/
FIN,310X115.52, 5.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK SPANISH
KB.INT00.077
KEYBOARD/W
ST,89,24P,BLACK,ESP,310X115.52,5.
5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK SLOVENIAN
KEYBOARD/W
ST,89,24P,BLACK,SLOV,310X115.52,
5.5mm
KB.INT00.078
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK SLOVAK
KEYBOARD/W
ST,89,24P,BLACK,SLVK,310X115.52,
5.5mm
KB.INT00.079
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK SLO/CRO
KEYBOARD/W
ST,89,24P,BLACK,CRO,310X115.52,
5.5mm
KB.INT00.080
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK RUSSIAN
KB.INT00.081
KEYBOARD/W
ST,88,24P,BLACK,RUS,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK PORTUGUESE
KB.INT00.082
KEYBOARD/W
ST,89,24P,BLACK,POR,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK POLISH
KEYBOARD/W
ST,89,24P,BLACK,POL,310X115.52,5
.5mm
KB.INT00.083
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK NORWEGIAN
KEYBOARD/W
ST,89,24P,BLACK,NOR,310X115.52,
5.5mm
KB.INT00.084
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK KOREAN
KB.INT00.086
KEYBOARD/W
ST,88,24P,BLACK,KOR,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK ITALIAN
KEYBOARD/W
ST,89,24P,BLACK,ITA,310X115.52,5.
5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK HUNGARIAN
KB.INT00.091
KEYBOARD/W
ST,89,24P,BLACK,HUN,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK GREEK
KB.INT00.092
KEYBOARD/W
ST,88,24P,BLACK,GRE,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK GERMAN
KB.INT00.093
KEYBOARD/W
ST,89,24P,BLACK,GER,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK FRENCH
KEYBOARD/W
ST,89,24P,BLACK,FRA,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK DUTCH
KB.INT00.096
KEYBOARD/W
ST,89,24P,BLACK,NL,310X115.52,5.5
mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK DANISH
KB.INT00.097
KEYBOARD/W
ST,89,24P,BLACK,DEN,310X115.52,5
.5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK CZECH
KEYBOARD/W
ST,89,24P,BLACK,CZE,310X115.52,5
.5mm
KB.INT00.076
KB.INT00.088
KB.INT00.094
KB.INT00.098
Chapter 6
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK TRADITIONAL CHINESE
KEYBOARD/W
ST,88,24P,BLACK,TWN,310X115.52,
5.5mm
KB.INT00.099
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK CANADIAN FRENCH
KEYBOARD/W
ST,89,24P,BLACK,CANFR,310X115.52, 5.5mm
KB.INT00.101
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK BRAZILIAN PORTUGUESE
KEYBOARD/W
ST,89,24P,BLACK,BRA,310X115.52,5
.5mm
KB.INT00.102
KEYBOARD
KEYBOARD 14_15KB-EV2T 89KS
BLACK BELGIUM
KB.INT00.103
KEYBOARD/W
ST,89,24P,BLACK,BEL,310X115.52,5.
5mm
KEYBOARD
KEYBOARD 14_15KB-EV2T 88KS
BLACK ARABIC/ENGLISH
KEYBOARD/W
ST,88,24P,BLACK,ARA,310X115.52,5
.5mm
LCD
LCD MODULE 14.1" WXGA NON-GLARE
W/ANTENNA FOR AU/LG
BOARD
INVERTER BOARD NEC/TOKIN 7312S3
INVERTER,5VDC,AC690V,55KHz,13
0X12.5
19.TCX0N.00
1
CASE/COVER/
BRACKET
ASSEMBLY
INVERTER INSULATOR
INSULATOR,INVERTER,FORMEX
GK-5BK
47.TLK0N.001
CABLE
LCD CABLE FOR AU/LG
CABLE,FLAT,40POS,219mm,I,LCM
50.TLN0N.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL FOR NON-CAMERA
FRU,LCD TOP CASE ASSEMBLY
60.TLN0N.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ ANTENNA &
MICROPHONE
FRU,LCD BOTTOM CASE
ASSEMBLY
60.TLK0N.005
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET LEFT
HINGE-W
BRACKET,DISPLAY,LEFT,6.5~7.5KG
33.TLK0N.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET RIGHT
HINGE-W
BRACKET,DISPLAY,RIGHT,6.5~7.5K
G
33.TLK0N.003
MICROPHONE
MICROPHONE
MIC.SET,-44DB,7.2X3,OMNI,680mm
23.TLK0N.003
LCD
LCD 14.1" WXGA AU B141EW04-V3
NON-GLARE 200NIT 16MS LF
LCM,14.1,TFT,WXGA,LVDS,400g
LK.14105.019
LCD
LCD MODULE 14.1" WXGA NON-GLARE
W/ANTENNA FOR SAMSUNG/CMO
BOARD
INVERTER BOARD NEC/TOKIN 7312S3
INVERTER,5VDC,AC690V,55KHz,13
0X12.5
19.TCX0N.00
1
CASE/COVER/
BRACKET
ASSEMBLY
INVERTER INSULATOR
INSULATOR,INVERTER,FORMEX
GK-5BK
47.TLK0N.001
CABLE
LCD CABLE FOR SAMSUNG/CMO
CABLE,FLAT,40POS,219mm,I,LCM
50.TLN0N.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL FOR NON-CAMERA
FRU,LCD TOP CASE ASSEMBLY
60.TLN0N.001
Chapter 6
KB.INT00.104
6M.TLN0N.00
1
6M.TLN0N.00
2
161
162
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ ANTENNA &
MICROPHONE
FRU,LCD BOTTOM CASE
ASSEMBLY
60.TLK0N.005
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET LEFT
HINGE-W
BRACKET,DISPLAY,LEFT,6.5~7.5KG
33.TLK0N.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET RIGHT
HINGE-W
BRACKET,DISPLAY,RIGHT,6.5~7.5K
G
33.TLK0N.003
MICROPHONE
MICROPHONE
MIC.SET,-44DB,7.2X3,OMNI,680mm
23.TLK0N.003
LCD
LCD 14.1WXGA SAMSUNG LTN141W3L01-0 NON-GLARE 16MS 200NITS LF
LCM,14.1,TFT,WXGA,LVDS,390g
LK.14106.010
LCD
LCD MODULE 14.1" WXGA GLARE W/
ANTENNA FOR AU/LG
BOARD
INVERTER BOARD NEC/TOKIN 7312S3
INVERTER,5VDC,AC690V,55KHz,13
0X12.5
19.TCX0N.00
1
CASE/COVER/
BRACKET
ASSEMBLY
INVERTER INSULATOR
INSULATOR,INVERTER,FORMEX
GK-5BK
47.TLK0N.001
CABLE
LCD CABLE FOR AU/LG
CABLE,FLAT,40POS,219mm,I,LCM
50.TLN0N.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL FOR NON-CAMERA
FRU,LCD TOP CASE ASSEMBLY
60.TLN0N.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ ANTENNA &
MICROPHONE
FRU,LCD BOTTOM CASE
ASSEMBLY
60.TLK0N.005
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET LEFT
HINGE-W
BRACKET,DISPLAY,LEFT,6.5~7.5KG
33.TLK0N.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET RIGHT
HINGE-W
BRACKET,DISPLAY,RIGHT,6.5~7.5K
G
33.TLK0N.003
MICROPHONE
MICROPHONE
MIC.SET,-44DB,7.2X3,OMNI,680mm
23.TLK0N.003
LCD
LCD 14.1" WXGA AU B141EW04-V4
GLARE 200NIT 16MS LF
LCM,14.1,TFT,WXGA,LVDS,400g
LK.14105.018
LCD
LCD MODULE 14.1" WXGA GLARE W/
ANTENNA FOR SAMSUNG/CMO
BOARD
INVERTER BOARD NEC/TOKIN 7312S3
INVERTER,5VDC,AC690V,55KHz,13
0X12.5
19.TCX0N.00
1
CASE/COVER/
BRACKET
ASSEMBLY
INVERTER INSULATOR
INSULATOR,INVERTER,FORMEX
GK-5BK
47.TLK0N.001
CABLE
LCD CABLE FOR SAMSUNG/CMO
CABLE,FLAT,40POS,219mm,I,LCM
50.TLN0N.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL FOR NON-CAMERA
FRU,LCD TOP CASE ASSEMBLY
60.TLN0N.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ ANTENNA &
MICROPHONE
FRU,LCD BOTTOM CASE
ASSEMBLY
60.TLK0N.005
6M.TLN0N.00
3
6M.TLN0N.00
4
Chapter 6
ACER PART
NO.
CATEGORY
PARTNAME
DESCRIPTON
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET LEFT
HINGE-W
BRACKET,DISPLAY,LEFT,6.5~7.5KG
33.TLK0N.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET RIGHT
HINGE-W
BRACKET,DISPLAY,RIGHT,6.5~7.5K
G
33.TLK0N.003
MICROPHONE
MICROPHONE
MIC.SET,-44DB,7.2X3,OMNI,680mm
23.TLK0N.003
LCD
LCD 14.1WXGA SAMSUNG LTN141W3L01-G GLARE 16MS 200NITS LF
LCM,14.1,TFT,WXGA,LVDS,390g
LK.14106.011
MAINBOARD
MAINBOARD MICHIGAN INTEL GM965
ICH8DH LF
FRU,MAIN BOARD ASSEMBLY
MB.TLN0B.00
1
MEMORY
SODIMM 512MB DDRII667 HYNIX
HYMP564S64CP6-Y5 LF
MEMORY MODULE,512MB,PC25300,DDR2, 200P,64MX64,0.45ns,5
KN.5120G.019
MEMORY
SODIMM 512MB DDRII667 NANYA
NT512T64UH8B0FN-3C LF
MEMORY MODULE,512MB,PC25300,DDR2, 200P,64MX64, 0.45ns,5
KN.51203.032
MEMORY
SODIMM 512MB DDRII667 SAMSUNG
M470T6554EZ3-CE6 LF
MEMORY MODULE,512MB,PC25300,DDR2, 200P,64MX64,
0.45ns,5,UB
KN.5120B.023
MEMORY
SODIMM 1GB DDRII667 HYNIX
HYMP512S64CP8-Y5 LF
MEMORY MODULE,1GB,PC25300,DDR2, 200P,128MX64, 0.45ns,5
KN.1GB0G.00
6
MEMORY
SODIMM 1GB DDRII667 NANYA
NT1GT64U8HB0BN-3C LF
MEMORY MODULE,1GB,PC2KN.1GB03.01
5300,DDR2, 200P,128MX64, 0.45ns,5 4
MEMORY
SODIMM 1GB DDRII667 NANYA
NT1GT64U8 HA0BN-3C LF
MEMORY MODULE,1GB,PC2KN.1GB03.00
5300,DDR2, 200P,128MX64, 0.45ns,5 9
MEMORY
SODIMM 1GB DDRII667 SAMSUNG
M470T2953EZ3-CE6 LF
MEMORY MODULE,1GB,PC25300,DDR2, 200P,128MX64,
0.45ns,5,UB
KN.1GB0B.01
1
MEMORY
SODIMM 1GB DDRII667 PROMOS
V916765G24QBFW-F5 LF
MEMORY MODULE,1GB,PC25300,DDR2,
200P,128MX64,0.45ns,5,UB
KN.1GB0M.00
1
MISCELLANEOU
S
LCD CUSHION RIGHT
BUMPER,DISPLAY,RIGHT,SILICONE
47.TLK0N.002
MISCELLANEOU
S
LCD CUSHION LEFT
BUMPER,DISPLAY,SILICONE
47.TLK0N.003
MISCELLANEOU
S
LCD CUSHION MIDDLE
BUMPER,DISPLAY,TOPMIDDLE,SILICONE
47.TLK0N.004
SPEAKER
SPEAKER SET
SPEAKER.SET,4OHM,2W,23.5mm,1
01X77X20-68X
23.TLK0N.002
SCREW
SCREW-I25050M (4.5D*0.8T)-BK-PATCH SCREW-I25050M(4.5D*0.8T)-BKPATCH
86.D03VN.00
2
SCREW
SCREW-I25060M-BNI-PATCH
SCREW-I25060M-BNI-PATCH
86.TLK0N.002
SCREW
SCREW BK PATC
SCREW,I,M2.5,3.5mm,M,4.5mm,0.8
mm,BK,PATC
86.TLK0N.003
SCREW
SCREW
SCREW-I25025M(4.5Dx0.8T)-BKPATCH
86.TCXVN.00
2
SCREW
SCREW
SCREW-I25040M(4.5Dx0.8T)-BKPATCH
86.TCXVN.00
5
Chapter 6
163
164
CATEGORY
PARTNAME
DESCRIPTON
ACER PART
NO.
SCREW
SCREW
SCREW,I,M2.5,3.0mm,M,4.5mm,0.8
mm,BNI,PAT
86.TCXVN.00
7
SCREW
SCREW
SCREW-I20050M(4.5Dx0.5T)-BKPATCH
86.TCXVN.00
4
SCREW
SCREW
SCREW-I-M2.0-3.0-M-4.0Dx0.3T-BKPATCH
86.TCXVN.00
6
SCREW
SCREW BNI PATC
SCREW,I,M2.0,3.0mm,M,4.5mm,.8m
m,BNI,PATC
86.TLK0N.004
SCREW
SCREW
SCREW,I,M1.6X0.35,3.5mm,MACHIN 86.TLK0N.005
E,2.6mm,0.
SCREW
SCREW-I30035M (D4.5X0.4T)-HARDENN1
SCREW-I30035M(D4.5X0.4T)HARDEN-N1
86.TLK0N.006
Chapter 6
Chapter 6
165
Appendix A
Model Definition and Configuration
TravelMate 6492 Series
Model
RO
Country Acer Part no Description
CPU
TM6492 WW
302G12
N
WW
S2.TLK06.001
TM6492-302G12N XPPTWW1
UMACF 2*1G/120/BT/6L/
5R_N_FP_0.3D_AL_EN11_Media
review
C2DT7300 N120GB5.4KS NSM8X
TM6492 WW
302G12
N
WW
S2.TLK0Z.001
TM6492-302G12N VB32TWW1
UMACF 2*1G/120/BT/9L/
5R_N_FP_0.3D_AL_EN11_Media
review
C2DT7300 N120GB5.4KS NSM8X
TM6492 TWN
102G16
N
GCTWN
LX.TLK0Z.006
TM6492-102G16N VB32TRTW1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_TC11
C2DT7100 N160GB5.4KS NSM8X
TM6492 TWN
102G16
N
GCTWN
LX.TLK0Z.007
TM6492-102G16N VB32TTW1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_TC11
C2DT7100 N160GB5.4KS NSM8X
TM6492 TWN
302G16
N
GCTWN
LX.TLK0Z.009
TM6492-302G16N VB32TRTW1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_TC11
C2DT7300 N160GB5.4KS NSM8X
TM6492 TWN
302G16
N
GCTWN
LX.TLK0Z.008
TM6492-302G16N VB32TTW1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_TC11
C2DT7300 N160GB5.4KS NSM8X
TM6492 EMEA Belgium
101G16
N
LX.TLK0Z.021
TM6492-101G16N VB32TRBE1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_NL13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Czech
101G16
N
LX.TLK0Z.020
TM6492-101G16N VB32TRCZ1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_SK11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Denmark
101G16
N
LX.TLK0Z.017
TM6492-101G16N VB32TRDK1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_NO13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Germany
101G16
N
LX.TLK0Z.018
TM6492-101G16N VB32TRDE1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_DE13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Switzerla
nd
101G16
N
LX.TLK0Z.039
TM6492-101G16N VB32TRCH1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_IT42
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Spain
101G16
N
LX.TLK0Z.029
TM6492-101G16N VB32TRES1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_ES22
C2DT7100 N160GB5.4KS NSM8X
Appendix A
HDD 1 (GB)
ODD
166
Model
RO
Country Acer Part no Description
CPU
HDD 1 (GB)
ODD
TM6492 EMEA France
101G16
N
LX.TLK0Z.012
TM6492-101G16N VB32TRFR1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_FR23
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.044
TM6492-101G16N VB32TREU1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_CS21
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.025
TM6492-101G16N VB32TREU4
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_FI12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.026
TM6492-101G16N VB32TREU3
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.014
TM6492-101G16N VB32TREU2
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_HU21
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.027
TM6492-101G16N VB32TREU5
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_PL11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Greece
101G16
N
LX.TLK0Z.041
TM6492-101G16N VB32TRGR1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_EL32
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Hungary
101G16
N
LX.TLK0Z.028
TM6492-101G16N VB32TRHU1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_HU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA UK
101G16
N
LX.TLK0Z.040
TM6492-101G16N VB32TRGB1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_EN14
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Italy
101G16
N
LX.TLK0Z.032
TM6492-101G16N VB32TRIT1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_IT12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Luxembo
urg
101G16
N
LX.TLK0Z.022
TM6492-101G16N VB32TRLU1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_IT42
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Holland
101G16
N
LX.TLK0Z.042
TM6492-101G16N VB32TRNL1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_NL12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Norway
101G16
N
LX.TLK0Z.023
TM6492-101G16N VB32TRNO1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_NO12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.013
TM6492-101G16N VB32TRME2
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_AR12
C2DT7100 N160GB5.4KS NSM8X
167
Appendix A
Model
RO
Country Acer Part no Description
CPU
HDD 1 (GB)
ODD
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.036
TM6492-101G16N VB32TRME6
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_EN14
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.038
TM6492-101G16N VB32TRME4
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.011
TM6492-101G16N VB32TRME2
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_AR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.037
TM6492-101G16N VB32TRME3
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_FR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Turkey
101G16
N
LX.TLK0Z.033
TM6492-101G16N VB32TRTR1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_TR11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Portugal
101G16
N
LX.TLK0Z.043
TM6492-101G16N VB32TRPT1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_PT12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Sweden/
Finland
101G16
N
LX.TLK0Z.019
TM6492-101G16N VB32TRSE1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_FI12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA South
Africa
101G16
N
LX.TLK0Z.015
TM6492-101G16N VB32TRZA1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_FR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA South
Africa
101G16
N
LX.TLK0Z.016
TM6492-101G16N VB32TRZA2
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_EN15
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Denmark
101G16
N
LX.TLK0Z.065
TM6492-101G16N VB32TRDK1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_NO13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Germany
101G16
N
LX.TLK0Z.071
TM6492-101G16N VB32TRDE1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_DE13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Belgium
101G16
N
LX.TLK0Z.047
TM6492-101G16N VB32TRBE1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_NL13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Czech
101G16
N
LX.TLK0Z.048
TM6492-101G16N VB32TRCZ1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_SK11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.049
TM6492-101G16N VB32TREU1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_CS21
C2DT7100 N160GB5.4KS NSM8X
Appendix A
168
Model
RO
Country Acer Part no Description
CPU
HDD 1 (GB)
ODD
TM6492 EMEA Spain
101G16
N
LX.TLK0Z.057
TM6492-101G16N VB32TRES1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_ES22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Switzerla
nd
101G16
N
LX.TLK0Z.066
TM6492-101G16N VB32TRCH1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_IT42
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA UK
101G16
N
LX.TLK0Z.064
TM6492-101G16N VB32TRGB1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN14
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.055
TM6492-101G16N VB32TREU5
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_PL11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Hungary
101G16
N
LX.TLK0Z.073
TM6492-101G16N VB32TRHU1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_HU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Greece
101G16
N
LX.TLK0Z.058
TM6492-101G16N VB32TRGR1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EL32
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.072
TM6492-101G16N VB32TREU4
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_FI12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.053
TM6492-101G16N VB32TREU3
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
101G16
N
LX.TLK0Z.054
TM6492-101G16N VB32TREU2
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_HU21
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA France
101G16
N
LX.TLK0Z.046
TM6492-101G16N VB32TRFR1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_FR23
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Luxembo
urg
101G16
N
LX.TLK0Z.051
TM6492-101G16N VB32TRLU1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_IT42
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Italy
101G16
N
LX.TLK0Z.075
TM6492-101G16N VB32TRIT1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_IT12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.061
TM6492-101G16N VB32TRME2
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_AR12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.074
TM6492-101G16N VB32TRME2
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_AR22
C2DT7100 N160GB5.4KS NSM8X
169
Appendix A
Model
RO
Country Acer Part no Description
CPU
HDD 1 (GB)
ODD
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.069
TM6492-101G16N VB32TRME3
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_FR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.063
TM6492-101G16N VB32TRME4
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
N
LX.TLK0Z.062
TM6492-101G16N VB32TRME6
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN14
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Turkey
101G16
N
LX.TLK0Z.060
TM6492-101G16N VB32TRTR1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_TR11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Portugal
101G16
N
LX.TLK0Z.056
TM6492-101G16N VB32TRPT1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_PT12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Norway
101G16
N
LX.TLK0Z.068
TM6492-101G16N VB32TRNO1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_NO12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Holland
101G16
N
LX.TLK0Z.050
TM6492-101G16N VB32TRNL1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_NL12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Sweden/
Finland
101G16
N
LX.TLK0Z.070
TM6492-101G16N VB32TRSE1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_FI12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA South
Africa
101G16
N
LX.TLK0Z.045
TM6492-101G16N VB32TRZA1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_FR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA South
Africa
101G16
N
LX.TLK0Z.067
TM6492-101G16N VB32TRZA2
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN15
C2DT7100 N160GB5.4KS NSM8X
TM6492 China
302G16
N
China
LX.TLK0Z.076
TM6492-302G16N VB32TRCN1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_SC11
C2DT7300 N160GB5.4KS NSM8X
TM6492 China
302G16
N
Hong
Kong
LX.TLK0Z.077
TM6492-302G16N VB32TRHK2
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_ZH21
C2DT7300 N160GB5.4KS NSM8X
TM6492 EMEA Sweden/
Finland
102G16
N
LX.TLK0Z.078
TM6492-102G16N VB32TRSE1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_FI12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Sweden/
Finland
102G16
N
LX.TLK06.005
TM6492-102G16N XPPTSE1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_FI12
C2DT7100 N160GB5.4KS NSM8X
Appendix A
170
Model
Country Acer Part no Description
CPU
TM6492 AAP
101G16
RO
Thailand
LX.TLK06.004
TM6492-101G16 XPPTTH1 UMACF
2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_TH21
C2DT7100 N160GB5.4KS NSM8X
HDD 1 (GB)
ODD
TM6492 AAP
101G16
Thailand
LX.TLK0Z.002
TM6492-101G16 VB32TRTH1
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_TH21
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Eastern
Europe
100512
N
LX.TLK0C.001 TM6492-100512N LINPUSTEU5
UMACF 1*512/120/BT/6L/
5R_N_FP_0.3D_AL_EN41
C2DT7100 N120GB5.4KS NSM8X
TM6492 EMEA Germany
101G16
N
LX.TLK06.006
TM6492-101G16N XPPTDE1
UMACF 2*512/160/BT/9L/
5R_N_FP_0.3D_AL_DE13
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Switzerla
nd
101G16
N
LX.TLK06.007
TM6492-101G16N XPPTCH1
UMACF 1*1G/160/BT/6L/
5R_N_FP_0.3D_AL_IT42
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Israel
101G16
LX.TLK0Z.086
TM6492-101G16 VB32TRIL1
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_HE31
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
301G16
N
LX.TLK0Z.081
TM6492-301G16N VB32TRSG1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7300 N160GB5.4KS NSM8X
TM6492 EMEA South
Africa
101G16
LX.TLK0Z.084
TM6492-101G16 VB32TRZA2
UMACF 2*512/160/BT/6L/
5R_abg_FP_0.3D_AL_EN15
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA South
Africa
101G16
LX.TLK0Z.079
TM6492-101G16 VB32TRZA1
UMACF 2*512/160/BT/6L/
5R_abg_FP_0.3D_AL_FR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
101G16
N
LX.TLK0Z.087
TM6492-101G16N VB32TRSG1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Russia
101G16
LX.TLK0Z.089
TM6492-101G16 VB32TRRU1
UMACF 2*512/160/BT/6L/
5R_abg_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Norway
102G16
N
LX.TLK0Z.090
TM6492-102G16N VB32TRNO1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_NO12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Norway
102G16
N
LX.TLK06.009
TM6492-102G16N XPPTNO1
UMACF 2*1G/160/BT/6L/
5R_N_FP_0.3D_AL_NO12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA France
301G16
N
LX.TLK06.008
TM6492-301G16N XPPTFR1
UMACF 1*1G/160/BT/6L/
5R_N_FP_0.3D_AL_FR23
C2DT7300 N160GB5.4KS NSM8X
TM6492 AAP
301G16
N
LX.TLK0Z.003
TM6492-301G16N VB32TRVN1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7300 N160GB5.4KS NSM8X
171
Singapor
e
Singapor
e
Vietnam
Appendix A
Model
Country Acer Part no Description
CPU
TM6492 AAP
301G16
N
RO
Indonesia LX.TLK0Z.010
TM6492-301G16N VB32TRID1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7300 N160GB5.4KS NSM8X
HDD 1 (GB)
ODD
TM6492 AAP
101G16
N
Indonesia LX.TLK0Z.005
TM6492-101G16N VB32TRID1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
101G12
N
Indonesia LX.TLK0Z.004
TM6492-101G12N VB32TRID1
UMACF 2*512/120/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7100 N120GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
LX.TLK0Z.085
TM6492-101G16 VB32TRME4
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
LX.TLK0Z.082
TM6492-101G16 VB32TRME2
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_AR12
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
LX.TLK0Z.088
TM6492-101G16 VB32TRME6
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_EN14
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
LX.TLK0Z.083
TM6492-101G16 VB32TRME2
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_AR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 EMEA Middle
East
101G16
LX.TLK0Z.080
TM6492-101G16 VB32TRME3
UMACF 2*512/160/BT/6L/
5R_bg_FP_0.3D_AL_FR22
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
101G16
N
Singapor
e
LX.TLK06.014
TM6492-101G16N XPPTSG1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
301G16
N
Singapor
e
LX.TLK06.015
TM6492-301G16N XPPTSG1
UMACF 2*512/160/BT/6L/
5R_N_FP_0.3D_AL_EN12
C2DT7300 N160GB5.4KS NSM8X
TM6492 EMEA Russia
101G16
LX.TLK0Z.024
TM6492-101G16 VB32TRRU1
UMACF 2*512/160/BT/9L/
5R_abg_FP_0.3D_AL_RU11
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
101G16
Thailand
LX.TLK06.017
TM6492-101G16 XPPTTH1 UMACF
1*1G/160/BT/6L/
5R_bg_FP_0.3D_AL_TH21
C2DT7100 N160GB5.4KS NSM8X
TM6492 AAP
101G08
Thailand
LX.TLK06.016
TM6492-101G08 XPPTTH1 UMACF
1*1G/80/BT/6L/
5R_bg_FP_0.3D_AL_TH21
C2DT7100 N80GB5.4KS
TM6492 EMEA Denmark
101G16
LX.TLK06.018
TM6492-101G16 XPPTDK1 UMACF
1*1G/160/BT/9L/
5R_abg_FP_0.3D_AL_NO13
C2DT7100 N160GB5.4KS NSM8X
TM6492 PA
102G16
N
Canada
LX.TLK06.013
TM6492-102G16N XPPTCA1
UMACF 2*1G/160/BT/9L/
5R_N_VP_FP_0.3D_AL_FR11
C2DT7100 N160GB5.4KS NSM8X
TM6492 PA
102G16
N
Canada
LX.TLK06.012
TM6492-102G16N XPPTCA1
UMACF 2*1G/160/6L/
5R_N_FP_0.3D_AL_FR11
C2DT7100 N160GB5.4KS NSM8X
Appendix A
NSM8X
172
Model
Country Acer Part no Description
CPU
TM6492 PA
102G16
N
USA
LX.TLK06.011
TM6492-102G16N XPPTUS1
UMACF 2*1G/160/BT/9L/
5R_N_VP_FP_0.3D_AL_EN32
C2DT7100 N160GB5.4KS NSM8X
TM6492 PA
102G12
N
USA
LX.TLK06.001
TM6492-102G12N XPPTUS1
UMACF 2*1G/120/6L/
5R_N_FP_0.3D_AL_EN32
C2DT7100 N120GB5.4KS NSM8X
TM6492 PA
102G12
N
USA
LX.TLK06.002
TM6492-102G12N XPPTUS1
UMACF 2*1G/120/6L/
5R_N_FP_0.3D_AL_EN33
C2DT7100 N120GB5.4KS NSM8X
TM6492 PA
102G12
N
Canada
LX.TLK06.003
TM6492-102G12N XPPTCA1
UMACF 2*1G/120/6L/
5R_N_FP_0.3D_AL_FR11
C2DT7100 N120GB5.4KS NSM8X
TM6492 PA
102G16
N
USA
LX.TLK06.010
TM6492-102G16N XPPTUS1
UMACF 2*1G/160/6L/
5R_N_FP_0.3D_AL_EN32
C2DT7100 N160GB5.4KS NSM8X
173
RO
HDD 1 (GB)
ODD
Appendix A
Appendix A
174
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions
are tested under Windows® XP Home, Windows® XP Pro environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the TravelMate 6492 Series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
175
Test Peripherals for TravelMate 6492
Category
Item
Model/Description
Basic PC Card
LAN Card
Xircom Ethernet Adapter 10/100 PC Card
Advanced PC Card
USB2.0 Card
ATEN PU-212 USB 2.0 PC Card [32 bit]
1394 Card
FireLink IEEE 1394 CardBus Card(2
Ports) [32 bit]
SCSI Card
ADAPTEC SlimSCSI 1480B SCSI Card
[32 bit]
Wireless Lan Card
D-link DWL-AG660 [32 bit]
3COM [32 bit]
3G data card
Sony Ericsson GC89 EDGE/WLAN
Bluetooth Card
Billionton Bluetooth PCMCIA Adapter [16
bit]
Phone Card
Nokia D211 GSM Phone Card [16 bit]
CF
Toshiba 5G
Hitachi MicroDrive 2G
I/O - Display
External monitor
BenQ FP791 Monitor
Benq H200 LCD TV
SAMPO PDP TV PM-42PS6
Projector
Acer (PD322)
Acer (PD113P)
TV / LCD-TV
Benq H200 LCD TV
HDMI
Sony KLV S3210 LCD TV
I/O - Parallel
Legacy (Parallel) Printer /
Scanner
CANON i865 Printer
I/O - Serial
Mouse
Logitech MouseMan Serial-MousePort
SAMPO PDP TV PM-42PS6
176
Appendix B
Category
Item
Model/Description
I/O - USB
Keyboard / Mouse
Logitech® MX™900 Bluetooth® Optical
Mouse
Microsoft Wireless Optical Mouse Blue
Moon WIN PS2/USB W/Tilt Wheel - K8000060
BENQ Wireless Optical Mouse Blue
Printer / Scanner
CANON i865 Printer
HP PSC1350 All in one Printer
EPSON PERFECTION 4870 PHOTO
Scanner
COMPAQ Scanner Flatbed S200 US
Speaker/Joystick
JS iFun USB Speaker (JS1200UA)
SANWA JY-PFFUW
Camera / DV
Nikon D50 Digital Camera
Logitec QuickCam Pro 4000 (1.3M pixels)
Storage Drive
IOGEAR 1394/USB 2.0 External HDD
BuffaloHD-160IU2(160GB)
Flash Drive
iPod shuffle M9725PA/A(1GB)
SanDisk ImageMate 8 in1 Card Reader
Floppy Drive
TEAC USB FDD FD05-PUB
Mitsumi FDD D353GUE
Hub
D-link 4 Port USB 2.0 HUB
ODD
I/O DATA DVR-UEH8 External x8 DVD
super multi drive
TEAC DVD ROM Slim COMBO Drive
TV Tuner
CTS portable TV BOX
PDA
Acer n50 Premum
Others
Microsoft Fingerprint Reader
I/O - Access Point
Access Point
DWL 7100AP Premier AG
I/O - Bluetooth
USB
TRENDNET Bluetooth VoIP Phone
Logitech® MX™900 Bluetooth® Optical
Mouse
PDA
Dopod 699 by IR, USB, Bluetooth
HP iPAQ Pocket PC by Bluetooth and
USB
I/O - IR
Appendix B
Printer
BT-PA04AU EPX Bluetooth USB Printer
Adapter (option: parallel)
Mobile phone
Nokia 6230i
Headset
Motorola (HT820)
Phone Card
Acer bluetooth VOIP Phone Card
PDA
Acer n50 Premum
Mobile phone
Dopod 699
Printer
HP LaserJet 6P Printer by IR
177
Category
Item
Model/Description
I/O - Card Reader
MMC
MMC CARD 64MB
RS-MMC+Adapter 128MB
MS
MSX-256 Memory Stick
MS Pro
Memory Stick PRO MSX-1GS
MS CARD 128MB
Memory Stick PRO MSX-2GS
MS Duo
Memory Stick Duo 128MB
SD
SD CARD 512MB(SDSDJ-512)
SanDisk Ultra II 2.0GB
SM
SM CARD 128MB
XD
xD CARD 128MB
xD CARD 256MB
I/O - 1394
Smart Card
Provide by Acer
Camera / DV
Sony DV Cam DCR-TRV320
Printer / Scanner
EPSON PERFECTION 4870 PHOTO
Scanner
CANON i865 Printer
Storage Device
ADTEC LHD-HA160FU2 IEEE1394 &
USB 2.0/1.1 HDD unit
IOGEAR 1394/USB 2.0 External HDD
ODD
I/O DATA DVR-UEH8 External x8 DVD
super multi drive
Sony DVD+-RW DUL-530A by USB /
1394
178
I/O - S-Video in
ODD
Joybee 610 DVD player
I/O - Audio
SPDIF/Audio Jack
CREATIVE INSPIRE Digital 5600
Speaker
Others - Software/Game
Software
MSN 8.0 or later
Software
Yahoo Messenger 8.1 or later
Software
Skype 2.5 or later
Software
Microsoft Office2007
PC Game
Command & Conquer2
PC Game
3 Hyper
PC Game
NBA live 2005
PC Game
Tiger Woods PGA TOUR 06
PC Game
Prince of Persia: Warrior Within
PC Game
Total War
PC Game
Need for Speed- Under Ground II (DX9)
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office.
Acer Branch Offices and Regional Business Units may access our website. However some information sources
will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and Server
models including:
q
Service guides for all models
q
User's manuals
q
Training materials
q
Bios updates
q
Software utilities
q
Spare parts lists
q
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our technical
material.
Also contained on this website are:
q
Detailed information on Acer's International Traveler's Warranty (ITW)
q
Returned material authorization procedures
q
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
179
180
Appendix C