Technical information | Acer 6410 Laptop User Manual

Acer
TravelMate 6460/6410
Service Guide
Service guide files and updates are available
on the ACER/CSD web. For more
information, please refer to http://
csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates of notebook TravelMate 6460/6410 service guide.
Date
September 26, 2006
II
Chapter
Updates
first release
Copyright
Copyright© 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any
form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior
written permission of Acer Incorporated.
III
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose.
Any Acer Incorporated software described in this manual is sold or licensed “as is”. Should the programs prove
defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any
defect in the software.
Acer is a registered trademark of Acer Incorporated.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
IV
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information related to the
current topic.
WARNING
Alerts you to any damage that might result from doing or not
doing specific actions.
CAUTION
Gives precautionary measures to avoid possible hardware
or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the
accomplishment of procedures.
V
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's “global” product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on
card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic
service guide. In such cases, please contact your regional offices or the responsible personnel/channel to
provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on
your regional web or channel. For whatever reason, if a part number change is made, it will not be noted in the
printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the
list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
VI
Chapter 1
System Specification
Specification
Operating System
•
Windows® VistaTM Capable
•
Windows® VistaTM Premium Ready (for selected models)
•
Genuine Windows® XP Professional x 64 Edition
•
Genuine Windows® XP Professional (Service Pack 2)
•
Genuine Windows® XP Home Edition (Service Pack 2)
Platform
•
Intel® Centrino® Duo mobile technology, featuring:
•
Intel® CoreTM 2 Duo processor T7200/T7400/T7600 (4MB L2 cache, 2/2.16/2.33GHz, 667MHz FSB),
or T5500/T5600 (2MB L2 cache, 1.66/1.83GHz, 667MHz FSB), supporting Intel® Extended Memory
64 Technology (Intel® EM64T)
•
Mobile Intel® 945GM/PM Express chipset (for selected model)
•
Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) or Intel® PRO/
Wireless 3945BG network connection (dual-mode 802.11b/g) Wi-Fi CERTIFIEDTM solution, supporting
Acer SignalUpTM wireless technology
System Memory
•
Up to 2GB of DDR2 533/667MHz memory, upgradeable to 4GB using two soDIMM modules (dualchannel support)
Display and Graphics
•
15.4” WSXGA + high-brightness TFT LCD, 1680 x 1050 pixel resolution, 16 ms response time, supporting
simultaneous multi-window viewing via Acer GridVistaTM
•
15.4” WXGA + high-brightness TFT LCD, 1280 x 800 pixel resolution, 16 ms response time, supporting
simultaneous multi-window viewing via Acer GridVistaTM
•
15” SXGA + high-brightness TFT LCD, 1400 x 1050 pixel resolution
•
15” XGA + high-brightness TFT LCD, 1024 x 768 pixel resolution
•
ATI MobilityTM Radeon® X1300 with up to 512MB HyperMemoryTM (128MB of dedicated GDDR2 VRAM,
up to 384MB of shared system memory), supporting ATI PowerPlayTM 5.0, Microsoft® DirectX® 9.0 and
DualViewTM (for selected models)
or
•
Mobile Intel® 945GM Express chipset with integrated 3D graphics, featuring Intel® Graphics Media
Accelerator (GMA) 950, up to 224MB of shared memory supporting Microsoft® DirectX® 9.0 and dual
independent display (for selected models)
•
Up to 2048 x 1536 resolution via non-integrated CRT display
•
MPEG-2/DVD hardware-assisted capability
•
16.7 million colors
•
S-video/TV-out (NTSC/PAL) support (for selected models)
Chapter 1
1
•
DVI-D (true digital video interface) support (for selected models)
Audio
•
Intel® High-Definition audio support
•
Two built-in Acer 3D Sonic (1.5W) stereo speakers
•
Built-in microphone
•
SoundBlaster ProTM and MS Sound compatible
Storage Subsystem
•
60/80/100/120/160GB or higher Serial ATA hard disk driver with Acer DASP (Disk Anti-Shock Protection)
•
Acer Media Bay hot-swappable 80/100/120/160GB Serial ATA second hard disk drive
•
Acer Media Bay hot-swappable optical drive:
•
•
8X DVD Super Multi double layer drive
•
DVD/CD-RW combo drive
5-in-1 card reader, supporting Secure Digital (SD), MultiMediaCard (MMC), Memory Stick® (MS), Memory
Stick PROTM (MS PRO), xD-Picture CardTM (xD) (for selected models)
Communication
•
Acer Video Conference featuring Voice and Video over Internet Protocol (VVoIP) support via Acer
OrbiCamTM and optional Acer Bluetooth® VoIP phone (for selected models)
•
Acer OrbiCamTM integrated 1.3 megapixel CMOS camera (for selected models), featuring:
•
225 degree ergonomic rotation
•
Acer VisageONTM technology
•
Acer PrimaLiteTM technology
•
Modem: 56K ITU V.92 with PTT approval; Wake-on-Ring ready
•
LAN: Gigabit Ethernet; ASF 2.0 support; Wake-on-LAN ready
•
WPAN: Bluetooth® 2.0 + EDR (Enhanced Data Rate)
•
WLAN: integrated Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) or
3945BG network connection (dual-mode 802.11b/g) Wi-Fi CERTIFIEDTM solution, supporting Acer
SignalUpTM wireless technology
Input Devices
•
Security access via TravelMate TPM-based fingerprint reader / TravelMate SmartCard reader (for
selected models)
•
88/89-key Acer FineTouchTM keyboard with five degree curve, inverted “T“ cursor layout, 2.5 mm
(minimum) key travel
•
12 function keys, four cursor keys, two Windows® keys, hotkey controls, embedded numeric keypad,
international language support
•
Dual navigation control, featuring Acer FineTrackTM with two FineTrackTM buttons and touch pad with 4way scroll button
•
Four easy-launch buttons: Empowering Key, email, Internet and user-programmable button
•
Two communication LED switches: WLAN and Bluetooth®
I/O Interface
•
2
Acer ezDock II and ezDock II+ connector
Chapter 1
•
ExpressCardTM/34 slot (for selected models)
•
PC Card slot (Type II)
•
TravelMate fingerprint reader (for selected models)
•
5-in-1 card reader (SD, MMC, MS, MS PRO, xD) (for selected models)
•
Three USB 2.0 ports
•
DVI-D port (for selected models)
•
IEEE 1394 port (for selected models)
•
Fast Infrared (FIR) port (for selected models)
•
External display (VGA) port
•
S-video/TV-out (NTSC/PAL) port (for selected models)
•
Headphones/speaker/line-out jack
•
Serial port
•
Microphone-in jack
•
Line-in jack
•
Ethernet (RJ-45) port
•
Modem (RJ-11) port
•
DC-in jack for AC adapter
Power Subsystem
•
ACPI 2.0 CPU power management standards: Stand-by and Hibernation power-saving modes support
•
71W 4800mAh 8-cell Li-Ion battery pack and 44.4W 4000mAh 6-cell Li-Ion battery pack
•
Acer QuicChargeTM technology:
•
•
80% charge in 1 hour
•
2-hour rapid charge system-off
•
2.5-hour charge-in-use
3-pin 90W AC adapter
Security
•
Acer DASP (Disk Anti-Shock Protection)
•
Acer GraviSense and Acer Anti-Theft HDD protection technologies (for selected models)
•
TravelMate TPM-based fingerprint solution (for selected models)
•
TravelMate SmartCard solution (for selected models)
•
TravelMate TPM (Trusted Platform Module) solution, Acer eDataSecurity Management support (for
selected models)
•
Kensington lock slot
•
BIOS user, HDD and supervisor passwords
Dimensions and Weight
•
360 (W) x 271 (D) x 35.5 (H) mm (14.2 x 10.6 x 1.4 inches)
•
3.12 kg (6.88 lbs.) with 8-cell battery pack and Acer Media Bay 6-cell second battery pack
•
2.85 kg (6.27 lbs.) with 8-cell battery pack and optical drive
•
2.7 kg (5.94 lbs.) with 6-cell battery pack and optical drive
Environment
•
Temperature:
•
Chapter 1
Operating: 5 oC to 35 oC
3
•
•
Non-operating: -20 oC to 65 oC
Humidity (non-condensing):
•
Operating: 20% to 80%
•
Non-operating: 20% to 80%
Warning!For safety reasons, do not use non-compliant parts when you add or change components.
4
Chapter 1
Block Diagram
DVI
CRT
S-VIDEO
( DOCK )
DVI ( MB )
DVI SW
PI5V330
Switch
DVI IC
CH 7307
ATI
VGA CHIP
M52/M54/M56
VRAM
128MB/256MB
Calistoga
945GM/PM
1466 uFCBGA
DMI x4
652 BGA
ICH7-M
SATA_HDD
HDD
SLG8LP462 (64PIN)
Clock Generator
( DOCK )
EXPRESS CARD
CARD READER
DDR2_SODIMM1
PI3L301D
LAN SW
RJ45 ( MB )
RJ45 ( DOCK )
LAN CONTROLLER IC
BCM5787MKMLG
IEEE 1394
(4 Pin)
1394 PORT 2
SATA_HDD
REV
On Docking
(6 Pin)
DOC. NUMBER
On Docking
1394 PORT 1
CARD BUS IC
TYPE II
CARDBUS
Controller
TSB43AB22
1394 CONN
OZ128
On Main Board
SIZE CODE
TITLE
INF_SLB9635TT
TPM 1.2
SOLT
( DOCK )
PARALLEL PORT
SMSC
SIO 1036
SMART CARD
OZ601
INTEL WRIELESS LAN
MINI CARD
ANT ANT ANT
DDR2_SODIMM0
1.8V, DDR2 Interface, 533/667 MHz
( MB )
SOLT
6 IN 1
( MB & DOCK )
SERIAL PORT
FIR
KIONIX KXP84
3-AXIS SENSOR
Touch PAD
&
Stick Point
Main Board
Multi-Bay
3.3V, PCI_Interface,33MHz
EXPRESS CARD
1.8V, DDR2 Interface, 533/667 MHz
PATA_ODD
SATA_RAID
SMSC
KBC1122
BIOS
FLASH ROM
PCI_EXPRESS X1
FSB, 533/667 MHz
(uFCPGA)
Yonah/Merom
PCI Express x16
4GB/Sec
3.3V, AZALIA
AZALIA
AUDIO CODEC
RTL ALC883D
MIC-JACK
HP-JACK
SPDIF OUT
SPEAKER
LINE IN
SATA_RAID
Module 56K
USB 0
CONN A
Switch
PI5V330
SPI FLASH
(HDCP)
USB 3
MDC / Modem
Express Card
RJ11
USB 1
CONN B
CRT ( MB )
BATTERY
USB 2
CONN C
S-VIDEO
USB 5
System Charger &
USB 4
Blue Tooth
LCM
Finger Printer
DC/DC System power
(IMVP-6 VR)
3.3V, LPC_Interface,33MHz
15.4" TFT
XGA/SXGA
USB 6
Camera
PORT REPLICATOR
Docking
5
Chapter 1
USB 7
Outlook Tour
Just for Starters...
Front View
#
#
Item
Item
Description
1
Acer Orbicam
1.3 megapixel web camera for video communication. (for selected
models)
2
Display screen
Also called Liquid-Crystal Display (LCD), displays computer output.
3
Acer FineTouch Keyboard
Serves to enter data into the computer.
4
Acer FineTrack
Touch-sensitive pointing device which functions like a computer
mouse when used together with the click buttons.
5
Microphone
Internal microphone for sound recording.
6
Fingerprint reader
Security identification. (for selected models)
7
Touch pad
Touch-sensitive pointing device which functions like a computer
mouse.
8
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the status of the
computer’s functions and components.
9
3D sonic speakers
Left and right speakers deliver stereo audio output.
10 11 Click buttons
(left, center and right)
12
6
Description
Palmrest
The left and right buttons work like the left and right mouse buttons;
the center button serves as a four-way scroll button.
Comfortable support area for your hands when you use the
computer.
Chapter 1
"Launch keys" on page 10
"Launch keys" on page 10
#
13
Item
Description
FineTrack buttons (left and
right)
Work like the left and right mouse buttons when used together with
the center-keyboard FineTrack.
14
Power button
Turns the computer on and off.
15
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the status of the
16
computer’s
and components.
"Launch keys"
on page functions
10
“Indicators”
on
page 27 used programs.
Easy-launch buttons
Buttons for launching frequently
“FineTrack basics” on page 29
"Easy-launch buttons" on page 28
Closed Front View
# #
#
Icon ItemItem
Icon
##
Item
Icon
Icon
#
Icon
Item Description
Item
Item
#
#
#
5
6#
Description
Indicates the computer’s power status.
Item
Indicates the computer’s battery status.
Description
Bluetooth
communication button/
indicator
Icon
Icon
Description
Item
Battery indicator
Icon
3
4#
Description
Power indicator
2
Description
Description
Description
"LaunchItem
keys" on page 10
Icon
Icon
1
Description
Item
Wireless
Enables/disables the Bluetooth communication. Indicates
the status of Bluetooth communication.
Description
Enables/disables the wireless function. Indicates the status
communication button/
indicator
of wireless LAN communication.
Infrared port
Interfaces with infrared devices (e.g., infrared printer and IRaware computer). (for selected models)
Item
Microphone-in jack Description
Accepts input from external microphones.
7
Line-in jack
Accepts audio line-in devices (e.g., audio CD player, stereo
walkman).
8
Headphones/speaker/
line-out jack
Connects to audio line-out devices (e.g., speakers,
headphones).
Latch
Locks and releases the lid.
9
N/A
# Icon
Chapter 1
Item
Description
7
Left View
#
"Easy-launch buttons" on page 10
Icon # Icon
#1
Item
Item
N/A
Icon
2
#
Icon
Ventilation
Item slots
Item
Icon
Enable the computer to stay cool, even after
Description
prolonged use.
4-pin IEEE 1394 port
Connects to IEEE 1394 devices. (for selected
Two USB 2.0 ports
Connect to USB 2.0 devices (e.g., USB mouse, USB
camera). (3 total)
Description
models)
3
#
Description Description
Item
Description
4
ExpressCard/34 slot
Accepts one ExpressCard module. (for selected
models)
5
5-in-1 card reader
Accepts Memory Stick (MS), Memory Stick Pro (MS
PRO), Multi Media Card (MMC), Secure Digital (SD)
and xD-Picture Card (xD). (for selected models)
# Icon
#
Icon
Item
Item
6
Description
PC Card slot
7
N/A
8
N/A
Description
Accepts one Type II PC Card.
PC Card slot eject
Ejects the PC Card from the slot.
button
Note:
SmartCard
Accepts the TravelMate SmartCard. (for selected
models)
Right View
#
#
8
Icon
Item
#
Description
Item
Item
Description
Description
1
Acer Media Bay optical
drive
Internal optical drive; accepts CDs or DVDs.
2
Optical disk access
indicator
Lights up when the optical drive is active.
3
Optical drive eject button
Ejects the optical disk from the drive.
4
Emergency eject hole
Ejects the optical drive tray when the computer is turned off.
#5
Icon
USB 2.0 Item
port
Description
Connects
to USB 2.0 devices (e.g., USB mouse, USB camera). (3
total)
Chapter 1
#
Icon
Item
Description
Rear View
# Icon Item
#
Icon
Description
Item
Description
Note:
#
##
# 1
Icon
Icon
Icon
Icon
2
#
Icon
2
#4
Note: Description
#
Icon Item
Item
Item
Description
Item
Description Description
Item
S-video port/TV out
port (NTSC/PAL) port
Connects to a television or display device with S-video
input. (for selected models)
Modem (RJ-11) port
Connects to a phone line.
Item
Description
Ethernet (RJ-45) port
Icon
Description
Serial port
Item
Connects to an Ethernet 10/100/1000-based networks.
Connects
to serial devices.
Description
5
Digital Video Interface - Supports digital video connections. (for selected models)
Digital port
6
External display (VGA)
port
Connects to an external display device (e.g., external
monitor, LCD projector).
7
DC-in jack
Connects to an AC adapter.
8
Kensington lock slot
Connects to a Kensington-compatible computers security
lock.
#
Icon
Item
Base
View
Note:
#
Icon Item
Description
Description
Note:
#
#
Item
Item
Description
Description
1
Acer Media Bay release
latch
Locks or unlocks Acer Media Bay device.
2
Battery lock
Locks the battery in position.
3
Battery latch
Releases the battery for removal.
Chapter 1
9
10
4
Battery bay
Houses the computer’s battery pack.
5
Hard disk bay
Houses the computer’s hard disk (secured with screws).
6
Acer DASP
Disk Anti-Shock Protection
7
Memory compartment
Houses the computer’s main memory.
8
ezDock II/II+ connector
Connects to Acer ezDock II/II+.
Chapter 1
"Launch keys" on page 10
Indicators
The computer has eight several easy-to-read status indicators, including five on the front panel. The power, battery
and wireless communication status indicators are visible even when the LCD display is closed.
#
#
#
Item
Description
Item
Description
"Launch keys"
on page 10
Description
Item
"Launch keys" on page 10
#
Icon
Item
Description
"Launch keys"
on page 10
Icon Icon Function
Icon Item
Function
#
#
#
Icon
Item
Icon
Icon
Description
Description
Description
Description Lights up when Num Lock is activated.
Num Lock
Caps Lock
Lights up when Caps Lock is activated.
HDD
Indicates when the hard disk drive is active.
Item
Description
Item Bluetooth
IndicatesDescription
the status of Bluetooth communication
Wireless LAN
Power
Battery
Indicates the status of wireless LAN communication
1. Charging:
Lights when the computer is on.
2. Fully charged:
Lights when the battery is being charged.
Note: The light shows amber when the battery is charging. The light shows green when the system is under
AC mode.
1. Charging:
2. Fully charged:
Chapter 1
11
Easy-launch Buttons
There are several conveniently located easy-launch buttons. They are one user-programmable
button, web
"Acer
Empowering
Technology"
on page Key
1
browser button, mail
button, and
Acer Empowering
. Press
to run the Acer Empowering Technology.
Although the mail and web browser buttons are pre-set to E-mail and Internet programs, they can be redefined by
users. To set the web browser, mail and programmable buttons, run the Acer Launch Manager.
"Launch Manager" on page 45
"Easy-launch
buttons"
"Easy-launch buttons"
on page
10 on page 10
Easy-launch button
Default application
Easy-launch button
Default application
Acer Empowering Technology (user-programmable)
Mail
E-mail application (user-programmable)
Web browser
Internet browser (user-programmable)
P
User-programmable
"Easy-launch buttons" on page 10
12
Chapter 1
FineTrack and FineTrack buttons
The built-in FineTrack is a pointing device that senses movement on its surface. This means the cursor responds
as you use your finger to move the FineTrack. Its central location on the keyboard provides optimum comfort and
support.
FineTrack Basics
The following items show you how to use the FineTrack and FineTrack buttons:
•
Using your finger, apply light, steady force on the FineTrack (1) to move the cursor.
•
Press the FineTrack left (2) and the right (3) buttons located below the keyboard to perform selection and
execution functions. These two FineTrack buttons are similar to the left and right buttons on a mouse.
Chapter 1
13
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds
as you move your finger across the surface of the touchpad. The central location on the palmrest provides
optimum comfort and support.
Touchpad Basics
The following items will show you how to use the touchpad.
•
Move your finger across the touchpad (2) to move the cursor.
•
Press the left (1) and right (4) buttons to perform selection and execution functions. These two buttons are
similar to the left and right buttons on a mouse. Tapping on the touchpad is the same as clicking the left
button.
•
Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics the
cursor pressing on the right scroll bar of Windows applications.
Function
Left button (1)
Right button
(4)
Main touchpad (2)
Execute
Quickly click twice.
Tap twice (at the same
speed as double-clicking
a mouse button).
Select
Click once
Tap once.
Drag
Click and hold, then use
finger on the touchpad to
drag the cursor.
Tap twice (at the same
speed as double-clicking
a mouse button); rest
your finger on the
touchpad on the second
tap and drag the cursor.
Access
context
menu
Scroll
Center
button (3)
Click once.
Click and hold
to move up/
down/left/
right.
Note: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to
your finger movement; hence, the lighter the touch, the better the response. Tapping hard will not increase the
touchpad’s responsiveness.
Note: By default, vertical and horizontal scrolling is enabled on your touch pad. It can be disabled under
Mouse settings in Windows Control Panel.
14
Chapter 1
Using Acer FineTouch Keyboard
The full-sized keyboard includes an embedded numeric keypad, separate cursor, lock, Windows, function and
special keys.
Lock Keys and Embedded Numeric Keypad
The keyboard has three lock keys which you can toggle on and off.
Lock
Key
Lock
key
Caps Lock
Description
Description
When Caps Lock is on, all alphabetic characters are typed in uppercase.
Num Lock
<Fn> + <F11>
When Num Lock is on, the right hand side numeric keypad is in numeric
mode. The keys function as a calculator (complete with the arithmetic
operators +, -, *, and /). When Num Lock is off, the keys assume cursor
<Fn> + <F11> and other shortcut functions.
Scroll Lock
<Fn> + <F12>
When Scroll Lock is on, the screen moves one line up or down when you
press the up or down arrow keys respectively. scroll Lock does not work
with some applications.
The embedded
numeric
keypad functions like a desktop numeric keypad. It is indicated by small characters
<Fn>
+ <F12>
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are
not printed on the keys.
Desired access
Num Lock on
Num Lock off
Number keys on
embedded keypad
Type numbers in a normal manner.
N/A
Cursor-control keys on
embedded keypad
Hold <Shift> while using cursorcontrol keys.
Hold <Fn> while using cursorcontrol keys.
Desired
Num
onletters on
Main keyboard
keys access Hold <Fn>
whileLock
typing
embedded keypad.
<Shift>
Num
Lock
Type the
letters
in aoff
normal manner.
<Fn>
<Fn>
Chapter 1
15
Windows keys
Key
Description
The keyboard has two keys that perform Windows-specific functions.
Key
Key
Description
Icon
Description
Windows key
Press alone. This key has the same effect as clicking on the Windows Start
button. It <launches
the Start menu. It can also be used with other keys to
> + <Tab>:
provide a variety of functions:
<
> + <E>:
+ <Tab>: Activates the next Taskbar button.
<
> + <F1>:
+ <E>: Opens the My Computer window.
<
> + <F>:
+ <F1>: Opens Help and Support.
+ <R>:
+ <F>: Opens the Find (All Files dialog box).
<
> + <M>:
<
> + <Tab>:
<
> + <E>:
+ <R>:
Opens
dialog box.
<Shift>
+ <the Run
> + <M>:
+ <M>: Minimizes all windows.
<Shift> +
Application key
<
> + <F1>:
+ <M>: Undoes the minimize all windows action.
This key has the same effect as clicking the right mouse button. It opens
the application’s context menu.
<
> + <F>:
+ <R>:
Hotkeys
<
> + <M>:
The computer employs hotkeys or key combinations to access
<Fn> most of the computer's controls like screen
brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before pressing
the other key in the hotkey combination.
<Shift> + <
Hotkey
Icon
Function
Hotkey
Icon
Function
Description
Function
Description
Function
Description
<Fn> + <F1>
Hotkey
Icon
Hotkey
Icon
<Fn>
<F1>
Hot+Key
<F1>
<Fn> <Fn>
+ <F1>
<Fn>
++<F1>
Icon
> + <M>:
Description
Function
Hot key help
Description
Displays help on hotkeys.
<Fn> + <F2>
<Fn> + <F2>
<Fn> ++<F2>
<Fn>
<F2>
"Acer eManager" on
<Fn>
Launches the
AcereManager"
eSettings in on
Acer Empowering
"Acer
page 20
Technology.
Acer eSettings
<Fn> + <F2>
<Fn>+++<F3>
<F3>
<Fn>
<F3>
<Fn>
<Fn> + <F3>
+++<F4>
<Fn>
<F4>
<Fn>
<F4>
<Fn> <Fn>
+
<F3>
page 20
page 20
"Acer eManager" on
Acer ePower
Management
"Acer ineManager"
Launches the Acer ePower Management
Acer
Empowering
pageTechnology.
20
Sleep
Leads the computer to Sleep mode.
<Fn> + <F4>
<Fn>
<Fn> ++ <F5>
<F5>
<Fn> <Fn>
+ <F4>
+ <F5>
16
Chapter 1
<Fn> + <F6>
<Fn> + <F6>
on
<Fn> + <F5>
<Fn>
<Fn> ++ <F4>
<F5>
<Fn> + <F4>
<Fn>
<Fn>+ +<F5>
<F4>
<Fn> + <F4>
<Fn>
+ <F5>
<Fn> + <F5>
<Fn>
<F5>
<Fn>
++<F6>
Hot
Key
<Fn>
+<F5>
<F6>
<Fn>
+
<Fn>
<Fn>++<F5>
<F5>
Icon
Function
Description
Display toggle
Switches the display output between the display
screen, external monitor (if connected) and both.
<Fn>
+<F7>
<F6>
<Fn>
<Fn>
<F6>
<Fn>
+++<F6>
<Fn>
++
<F6>
<Fn>
<F7>
<Fn>
<F6>
Screen blank
Turns off the display screen backlight to save power.
Press any key to return.
<Fn> + <F6>
<Fn> + <F7>
Touchpad
toggle
Turns the internal touchpad on and off.
Speaker toggle
Turns the speakers on and off.
Volume up
Increases the sound volume.
Volume down
Decreases the sound volume.
Brightness up
Increases the screen brightness.
Brightness
down
Decreases the screen brightness.
<Fn> + <F6>
<Fn>
<F7>
<Fn>
<F7>
<Fn>
<F7>
<Fn>
+ +<F7>
<Fn>
++++<F7>
<F8>
<Fn>
<Fn>
<F8>
<Fn> + <F8>
<Fn>
++
<Fn>
<F8>
<Fn>
<F8>
<Fn>
++++<F8>
<F7>
<Fn>
<< >>
<Fn>
<Fn> + <F8>
<Fn> + <F8>
<Fn>
+ ++<<K>
<Fn>
< >>
<Fn>
<Fn>
+<
>
<Fn>
+++<F8>
<Fn>
<Fn>
<< >>
<Fn>
+
>>
<Fn>
+<<L>
<Fn>
<Fn>
++<
<
<Fn> + < >
<Fn> + < >
<Fn>
+ << >>
<Fn>
<Fn> ++<J>
<Fn>++<<
<Fn>
<Fn> + <
>
>
>
<Fn>
+ <>
<Fn>
+
<Fn>
+<
<
>>
<Fn> + <
>
<Fn>
< >
<Fn>+++<
<I>
<Fn>
<Fn>
<Fn>
++<< >>>
<Fn> + <
>
<Fn> +
+<
< >>
<Fn>
Special
<Fn>
+ < keys
>
You can locate the Euro symbol and the US dollar sign on the upper-center and/or bottom-right side of the
<Fn>
+< >
keyboard.
<Fn> + <
<Fn> + <
>
>
The Euro Symbol
1. Open a text editor or word processor.
2. Either press Euro key on the bottom-right edge of the keyboard, or hold <Alt Gr> key then press the number
<5> key on the upper-center edge of the keyboard.
Alt Gr>
Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
<5>
typography/faq/faq12.htm for more information.
The US Dollar Sign
Note
1. Open a text editor or word processor. www.microsoft.com/typography/faq/faq12.htm
2. Either press Dollar key on the bottom-right edge of the keyboard, or hold <Shift> and then press the <4> key
on the upper-center edge of the keyboard.
Note: This function varies according to the language settings.
Chapter 1
<Shift>
<4>
17
Acer OrbiCam
The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on top of the LCD panel. The
camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the
back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so you transmit
the best video conference quality over an instant messenger service.
#
#
Item
Item
#
Item
1
Lens
2
Power indicator
Rotating the Acer OrbiCam
The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the illustrations
below:
Note: Do NOT rotate the camera
Note: clockwise to prevent damage to the device.
For your convenience, the camera snaps 45 degrees to match the position of your face in front or at the back of
the LCD panel.
Note:
18
Chapter 1
Launching the Acer OrbiCam
To launch the Acer OrbiCam, double-click on the Acer OrbiCam icon on the desktop, or click Start > All Programs
> Acer > Acer OrbiCam. The Acer OrbiCam capture window will appear as below.
Changing the Acer OrbiCam Settings
Resolution
To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window,
then select the desired resolution.
Note: Setting the camera resolution to 640 x 480 or larger does not change the capture window size.
Chapter 1
19
Options
Click Options to display the Window, Preview, and Folder tabs. Use the options to change the capture window
size, preview settings, and the folder for captured photos or videos.
20
Chapter 1
Camera Settings
Basic Settings
Click the Camera Settings icon on the bottom right corner of the capture display, then select Camera Settings
from the pop-up menu. You can adjust the Video, Audio, and Zoom/Face tracking options from this window.
Chapter 1
21
Capture Settings
From the Camera Settings window, click the Driver Settings button. The Properties window will appear.
Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness, etc.
Advanced Settings allows you to achieve gain control, implement image mirror, select image enhancements and
anti-flicker settings, and turn on/off the camera indicator.
Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature on or off.
Capturing Photos/Videos
To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a Picture
or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player automatically
launches to display or play a preview of the photo/video clip.
Note: By default, all photos and videos are saved in the My Pictures and My Videos folder.
22
Chapter 1
Using the Acer OrbiCam as Webcam
The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application. To
use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can now
broadcast from your location to an IM partner anywhere in the world.
Enabling the Acer VisageON
(for 1.3 megapixel camera models only)
The Acer VisageON technology comes with two features: Face tracking. The face tracking feature tracks your
head movement and automatically centers your face in the capture window.
Note: The face tracking feature is not capable of centering your face beyond the capture window frame.
Minimal head movements are tracked more efficiently.
Please follow the steps below to enable the Acer VisageON.
1. Right click on this icon, then select VisageON from the pop-up menu.
The VisageON window will appear as below:
2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings
and options in the right section.
Using the Face Tracking Feature
To use the face tracking feature:
1. Click the left icon down arrow button, then select Single User or Multiple Users from the pop-up menu. For
multiple users, the face tracking feature automatically centers all the users’ face in the capture window,
otherwise the utility centers the face of the user closest to the camera.
2. Click the right icon to zoom in/out or reset the current view.
Chapter 1
23
3. Click VisageON to display a menu that allows to change the configuration of the camera, face tracking and
video effects settings.
24
Chapter 1
Acer Empowering Technology
Acer’s innovative Empowering Technology toolbar makes it easy to have access to the frequently used functions
and manage the notebook. Displayed by default in the upper-right corner of the screen, it features the following
handy utilities:
•
Acer eNet Management hooks up to location-based networks intelligently.
•
Acer ePower Management extends battery power via versatile usage profiles.
•
Acer ePresentation Management connects to a projector and adjusts dispaly settings conveniently.
•
Acer TPM-based eDataSecurity Management protects data with passwords and advanced encryption
algorithms in TPM.
•
Acer eLock Management limits access to external storage media and removable data devices.
•
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eSettings Management accesses system information and adjusts settings easily.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry setting.
For more information, right click on the Empowering Technology toolbar, then select the Help or Tutorial function.
Empowering Technology Password
Before using Acer eLock Management and Acer eRecovery Management, You must initialize the Empowering
Technology password. Right click on the Empowering Technology toolbar and select Password Setup to do so. If
you do not initialize the Empowering Technology password, you will be prompted to do so when running Acer
eLock Management or Acer eRecovery Management for the first time.
Note: If you lose your password, there is no method to reset it except by reformatting your notebook or taking
your notebook to an Acer Customer Service Center. Be sure to remember or write down your password.
Chapter 1
25
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a variety of
locations. To access this utility, either click on the Acer eNet Management icon on your notebook, or start the
program from the Start menu. You also have the option to set Acer eNet Management to start automatically when
you boot up your PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the freedom
to manually adjust the settings to meet your needs.
Acer eNet Management can save network settings for a location to a profile, and automatically switch to the
appropriate profile when you move from one location to another. Settings stored include network connection
settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings.
Security and safety concerns mean that Acer eNet Management does not store username and password
information.
26
Chapter 1
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface.
AC Mode (Adapter Mode)
The default setting is Maximum Performance. You can adjust CPU speed, LCD brightness and other settings, or
click on buttons to turn the following functions on/off: wireless LAN, Bluetooth, CardBus, fireware (1394), wired
LAN and optical device if supported.
DC Mode (Battery Mode)
There are four pre-defined profiles: Entertainment, Presentation, Word Processing, and Battery Life. You can also
define up to three of your own.
To Create a New Power Profile
1. Change power settings as desired.
2. Click Save as... to save to a new power profile.
3. Name the newly created profile.
4. Select whether this profile is for Adapter or Battery mode, then click OK.
5. The new profile will appear in the profile list.
Battery Status
For real-time battery life estimates based on current usage, refer to the panel on the upper half side of the window.
Chapter 1
27
For additional options, click Settings to:
28
•
Set alarms.
•
Reload factory defaults.
•
Select what actions to be taken when the cover is closed or the power button is pressed.
•
Set passwords for accessing the system after Hibernation or Stand-by.
•
View information about Acer ePower Management.
Chapter 1
Chapter 1
29
Acer ePresentation Management
Acer ePresentation Management lets you project your computer’s display to an external device or projector using
the hotkey: <Fn> + <F5>. If auto-detection hardware is implemented in the system and the external display
supports it, your system display will be automatically switched out when an external display is connected to the
system. For projectors and external devices that are not auto-detected, launch Acer ePresentation Management to
choose an appropriate display setting.
Note: If the restored resolution is not correct after disconnecting a projector, or you need to use an external
resolution that is not supported by Acer ePresentation Management, adjust your display settings using Display
Properties or the utility provided by the graphics vendor.
30
Chapter 1
Acer TPM-Based eDataSecurity Management
Acer TPM-based eDataSecurity Management is a handy file encryption utility that protects the files from being
accessed by unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for
quick and easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messenger and
Microsoft Outlook.
The Acer eDataSecurity Management setup wizard will prompt you for a supervisor password and default
encryption. This encryption will be used to encrypt files by default, or you can choose to enter your own file-specific
password when encrypting a file.
Acer eDataSecurity Management can be integrated with TPM on computers equipped with the TPM hardware. On
computers equipped with the TPM hardware, there will be additional Acer eDataSecurity Management system
setup and administration procedures which allow the user to utilize TPM for the PSD and the File/Folder
encryption functions. If the Use TPM option is selected during Acer eDataSecurity Management’s initial system
setup or system administration, the PSD and the File/Folder encryption functions will be protected by TPM.
Note: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt your encrypted file! Be sure to safeguard all related passwords!
Chapter 1
31
32
Chapter 1
Acer eRecovery Management
Acer eRecovery Management is a powerful utility with the need for recovery disks provided by the manufacturer.
The Acer eRecovery Management utility occupies space in a hidden partition on the system’s HDD. Be default,
user-created backups are stored on D:\ drive. Acer eRecovery Management provides:
•
Password protection
•
Recovery of applications and drives
•
Image or data backup:
•
•
Backup to HDD (set recovery point)
•
Backup to CD or DVD
Image/data recovery tools:
•
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent user-defined recovery point)
•
Recovery from CD or DVD
Note: If the computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To ensure the
best results when recovering the system using a CD or Acer eRecovery Management, detach all peripherals
(except external Acer ODD, if equipped), including the Acer ezDock.
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specification, change BIOS passwords or other
Windows settings, and to monitor the system health status.
Acer eSettings Management also:
Chapter 1
33
34
•
Provides a simple graphical user interface for navigation.
•
Displays general system status and advanced monitoring for power users on Acer computer.
Chapter 1
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of the Acer notebook.
It provides an express optimization method to release unused memory and disk space quickly. The user can also
enable advanced options for full control over the following options:
•
Disk optimization: removes unneeded items and files.
•
Speed optimization: improves the usability and performance of the Windows XP system.
•
Memory optimization: releases unused memory and check usage.
Chapter 1
35
Using the System Utilities
Note: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
Start Control Panel Display
To enable the dual monitor feature of the notebook, first ensure
Settings
(2)that the second monitor is connected, then select
Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and
windows
desktop
onto
this
then click the check boxExtend
Extend mymy
windows
desktop onto
this monitor.
Finally,
clickmonitor
Apply to confirm the new
settings and click OK to complete the process.
Apply
OK
Note: This feature is only available on certain models.
Note:
Settings
Apply
Start Control Panel Display
(2)
Extend my windows desktop onto this monitor
OK
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on
the same screen. To access this function, please go to Start > All Programs and click on Acer GridVista. You
All Programs
Acer GridVista
may choose any one of the fourStart
display
settings indicated below:
Start All Programs
Acer GridVista
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer GridVista is
simple to set up:
1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
36
Chapter 1
Note: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Note:
Note:
Launch Manager
Launch Manager allows you"Easy-launch
to set the four buttons"
easy-launch
above the keyboard. You can access the
onbuttons
page located
24
Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
Start All Programs
Launch Manager
"Easy-launch buttons" on page 24
Chapter 1
37
Norton AntiVirus
Norton AntiVirus is an anti-virus software that finds and repairs infected files, and protects against viruses to keep
you computer data safe and secure.
How do I check for viruses?
A Full System Scan scans all files on your computer. To perform a system scan:
Norton AntiVirus
1. Start Norton Antivirus: Double click on the Norton AntiVirus Icon on the desktop or click on the Start menu in
Start
Programs
the Windows task bar, highlight Programs, and select Norton Antivirus.
Norton AntiVirus
2. In the Norton Antivirus main window, click Scans.
Scans
Scans
Run Full System Scan
3. In the Scans panel, click Run Full System Scan.
4. When the scan is complete, a scan summary appears. Click Finished.
Finished
You can schedule customized virus scans that tun unattended on specific dates and times or at periodic intervals.
If you are using the computer when the scheduled scan begins, it runs in the background so that you do not have
to stop working.
For more information, please refer to the Norton AntiVirus Help menu.
38
Chapter 1
Hardware Specification and Configuration
Processor
Item
Specification
Type
Intel Core 2 Duo processor T7200/T7400/T7600 (4MB L2 cache, 2/2.16/
2.33GHz, 667MHz FSB), or T5500/T5600 (2MB L2 cache, 1.66/1.83GHz,
667MHz FSB), supporting Intel® Extended Memory 64 Technology (Intel®
EM64T)
Feature
• Dual core processor for mobile with enhanced performance
®
TM
• Intel® 64 architecture
• Intel Architecture with Dynamic Execution support
• On-die, primary 32KB instruction cache and 32KB write-back data cache per
core
• On-die, up to 4MB second level shared cache with Advanced Transfer Cache
Architecture
• Data Prefetch Logic
• Streaming SIMD Extensions 2 (SSE2), Streaming SIMD Extensions 3
(SSE3) and Supplemental Streaming SIMD Extensions 3 (SSSE3)
• 667MHz, Source-Synchronous FSB for Standard Voltage processors
• Advanced Power Management features including Enhanced Intel
SpeedStep® Technology
• Intel® Enhanced Deeper Sleep state and Dynamic Cache Sizing
• Digital Thermal Sensor
• Micro-FCPGA and Micro-FCBGA packaging technologies
• Intel® Visualization Technology
• Execute Disable Bit support for enhanced security
North Bridge
Item
Specification
Chipset
Intel 945GM/PM
Feature
• 667/533MHz Front Side Bus: Intel® CoreTM Duo and Intel® CoreTM Solo
processors with up to 25% faster data transfer rate compared to the previous
generation bus speed
• Two SODIMMs up to 4GB max. system memory
• Memory Type: DDR2 667/553MHz
• Memory Channels: dual/single channel
• ECC Parity: No for both
• Integrated Graphics: Intel GMA 950 for 945GM only
• PCI Express x16 Interface: delivers greater than 3.5 times the bandwidth
over the traditional AGP interface and supports the latest high performance
graphics cards.
• Integrated TV out for 945GM only
• LVDS: up to UXGA (1600 x 1200) for 945GM only
• Dual Display Options: concurrent/simultaneous
®
• Intel® High Definition (HD) Audio 24 bits 192KHz, AC’97 2.3 audio, integrated
audio support enables premium sound and delivers advanced features such
as multiple audio streams and jack re-tasking.
• Integrated high speed USB 2.0: supports for eight USB 2.0 peripherals
• North Hub Package: 1466 FCBGA 37.5 mm x 37.5 mm
• South Hub Package: 652 FCBGA 31 mm x 31 mm
Chapter 1
39
South Bridge
Item
Specification
Chipset
ICH7M
Feature
•
•
•
•
•
•
•
Direction Media Interface 10GB/s each direction, full duplex
Four PCI Express root ports, PCI Express 1.0a support
PCI 2.3 specification at 33MHz
Bus master IDE controller (Ultra 100/66/33 support)
Integrated Serial ATA controller
USB 2.0 host controllers
Compliant with AC’97 2.3 interface
• Intel® Matrix Storage Technology: configures the ICH7 SATA controller as a
RAID controller supporting RAID 0/1
• AC’97 2.3 Codec support
• Low pin count (LPC) interface
• Enhanced DMA controller, two cascaded 8237 DMA controllers, LPC DMA
support
• ACPI 3.0 Power management
System Memory
Item
Feature
Specification
•
•
•
•
•
Built-in 945GM/PM
DDRII 533/667MHz SDRAM memory interface design
0MB DDR RAM on board
Two SODIMMS slots
Maximum memory up to 4GB (with two 2GB SODIMMs)
BIOS
Item
Description
Vendor
Phoenix
Version
0.94.06
ROM type
Flash ROM
Feature
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
40
Acer UI support
Multi-boot support
Suspend to RAM (S3) / Disk (S4)
Various hot keys for system control
Support boot option: HDD / Removable device (media bay device) / all USB
ports
Support protocols: SMBIOS 2.4, PCI 2.2, WFM 2.0
ACPI 2.0 compliance with Speedstep, C1, C2, C3, C4 and S3, S4 support for
mobile CPU
DMI utility for BIOS serial number configurable/asset tag
PXE support
BIOS virus protection
WinFlash support
Wake on LAN from S3
Wake on LAN from S4 and S5 in AC mode
TPM 1.2 BIOS support
D to D recovery support
Chapter 1
Keyboard
Item
Description
Chip
KBC1122
Features
• 88/89 keys
• Windows logo key: yes
• Internal and external keyboard work simultaneously: plug USB keyboard to
the USB port directly support
Modem
Item
Description
Features
•
•
•
•
56K, V.90/V.92, WWDAA
Wake-on-Ring support
Apply CISPR22
MDC 1.5 card
Connector type
RJ-11
Audio Codec & Amplifier
Item
Description
Controller
Realtek ALC883D
Feature
• HD audio
• SNR > 85, high-performance DACs with 95dB SNR (A-weighting), ADCs with
85dB SNR (A-weighting)
• Internal microphone
• Two speakers, at least 1.5W/30cc for each
Wireless LAN
Item
Description
Controller
ICH7M
Card type
Mini-PCI
Features
•
•
•
•
•
802.11a/b/g or 802.11b/g
Built-in two antennae
WiFi, WPA2, WMM
CCX V4 and above
Placed on the top of LCD or on the sides of LCD latches
LAN Interface
Item
Description
LAN controller
BCM5787MKMLG
Feature
•
•
•
•
PCI-E GbE LAN
WOL from S5 (AC mode) support
LDCM support
ASF2.0 support
IEEE 1394
Item
Controller
Chapter 1
Description
TSB43AB22
41
Item
Feature
Description
• PCI single chip solution with PCI 2.2 compliant
• OHCI V1.1
• 4-pin IEEE 1394
PCMCIA Express Card & Express Card
Item
Description
Chip
OZ601 + OZ27 C10
Feature
• One type II PC card
• PCI-Express narrow type card
VRAM
Item
Description
Chip
ATI M54P
Feature
• GDDR2 VRAM speed >/= 350MHz
• Discrete 64MB/128MB with Hyper Memory technology, up to 512 MB in OS
• UMA: DVMT3.0, up to maximum DVMT (default 64MB)
Hard Disk Drive
SEAGATE
Model
ST9160821AS
ST9120821AS
ST9100824AS
ST98823AS
ST96812AS
Formatted Gbytes (512 bytes/sector): 160 / 120 / 100 / 80 / 60
Physical read/write head: 4 / 4 / 4 / 3 / 2
Discs: 2 / 2 / 2 / 1 / 1
Spindle Speed (RPM): 5400 / 5400 / 5400 / 5400 / 5400
I/O data transfer rate (Mbytes/sec. max.): 150 / 150 / 150 / 150 / 150
Internal transfer rate (Mbytes/sec. max.): 57.6 / 57.6 / 57.6 / 57.6 / 57.6
ATA data transfer mode supported:
SATA 1.0, SATA II, PIO modes 0-4, Multiword DMA modes 0-2, Ultra DMA modes 0-6
Cache buffer: 8MB
Bytes per sector: 1024 / 1024 / 1024 / 1024 / 1024
Voltage tolerance: +5.0V +/- 5%
TOSHIBA
Model
MK1234GSX
MK1032GSX
MK8032GSX
Formatted Gbytes (512 bytes/sector): 120 / 100 / 80
Physical read/write head: 4 / 4 / 4
Discs: 2 / 2 / 2
Spindle Speed (RPM): 5400 / 5400 /5400
Internal transfer rate (Mbits/sec. max.): 244.7~474.4 / 236.1~456.0 / 214~422
I/O data transfer rate (Mbytes/sec. max.): 150 / 150 / 150
ATA data transfer mode supported: ATA7, SATA 1.0a, SATA II 1.2, Multi word DMA, Ultra DMA modes,
Advanced PIO mode settings and commands
42
Chapter 1
TOSHIBA
Cache buffer (MB): 8 / 16 / 8
Bytes per sector: 512 / 512 / 512
Voltage tolerance: +5.0V +/- 5%
HGST
Model
HTS541616J9SA00
HTS541010G9SA00
HTS541080G9SA00
HTS541060G9SA00
Formatted Gbytes: 160 / 100 / 80 / 60
Physical read/write head: 4 / 4 / 4 / 3
Discs: 2 / 2 / 2 / 2
Spindle Speed (RPM): 5400 / 5400 / 5400 / 5400
Internal transfer rate: N/A
I/O data transfer rate: 150 (MB/sec.) / 493 (Mbps) / 493 (Mbps) / 493 (Mbps)
ATA data transfer mode supported: N/A
Cache buffer (MB): 8 /
Bytes per sector: 512 / 512 / 512 / 512
Voltage tolerance: +5.0V +/- 5%
WD
Model
WD1200BEVS
WD1000BEVS
WD800BEVS
WD600BEVS
Formatted Gbytes: 120 / 100 / 80 / 60
Interface: SATA 150MB/s
RoHS compliant: Yes / Yes / Yes / Yes
Spindle Speed (RPM): 5400 / 5400 / 5400 / 5400
Average read seek:12.0 ms (average)
Track-to-track seek: 2.0 ms (average)
Average latency: 5.5 ms
Cache buffer (MB): 8 / 8 / 8 / 8
Bytes per sector: 512 / 512 / 512 / 512
Voltage tolerance: +5.0V +/- 5%
Chapter 1
43
Optical Disk Drive: Combo 24X
Item
Description
Model
PHILIPS SCB5265
PANASONIC UJDA-770
Buffer memory
2MB
2MB
Interface
IDE/ATAPI interface (compliant to
ATA/ATAPI-5)
ATAPI interface (PIO mode, DMA
mode, Ultra DMA mode)
Applicable disc format
• DVD (read): DVD 5, 9, 10, 18,
DVD-ROM, DVD-Video, DVD-R
4.7GB, DVD-R 3.95GB, DVD-RW,
DVD+R, DVD+RW, Multi-Border
DVD-R/DVD-RW, Multi-Session
DVD+R, DVD+RW, DVD-RAM
• CD (read): CD-DA, CD-ROM
Mode-1, CD-ROM/XA Mode-2
Form-1 and Mode-2 Form-2, CD-i
ready, Video-CD (MPEG-1),
Karaoke CD, Super Video CD,
Photo-CD, Enhanced CD, CD
Plus, CD Extra, i-tax CD, CD-Text,
CD-R, CD-RW
• CD (write): CD-DA, CD-ROM
Mode-1, CD-ROM/XA Mode-2
Form-1 and Mode-2 Form-2, CD-i,
Video-CD, CD-Text
• DVD: DVD-ROM, DVD-Video,
DVD-RAM (2.6GB/4.7GB), DVDR, DVD-RW (Ver. 1.1, Multi-Border
support), DVD+RW, DVD+R
• CD: CD-DA, CD-ROM, CD-R, CDRW, CD-ROM XA, Photo (MultiSession), Video CD, CD-Extra
(CD+), CD-text
Power requirement
max. 1300mA
max. 1800mA
Input voltage
+5V +/- 5% (Operating)
5V +/- 0.25V (operating)
Optical Disk Drive: DVD Super Multi 8X
Item
44
Description
Model
TSST TS-L632D
PANASONIC UJ850
UAA
8X Super Multi (DL)
PHILIPS SDVD-8821
Buffer memory
2MB
2MB
2MB
Interface
IDE/ATAPI interface
(compliant to ATA/
ATAPI-5)
ATAPI interface (PIO
mode, DMA mode,
Ultra DMA mode)
IDE/ATAPI interface
(compliant to ATA/
ATAPI-5)
Chapter 1
Item
Description
Applicable disc format
Media Compatibility
• DVD: 5/9/10/18 G
DVD-Single / Dual
(read only), 4.7GB
DVD+R (read &
write), 4.7GB DVD-R
(read & write), 4.7GB
DVD+RW (read &
write), 4.7GB DVDRW (read & write),
DVD+R dual (read &
write), DVD-R dual
(read & write), DVDRAM (read & write),
80mm DVD
• CD: 650MB CD-ROM
(read only), 80 mm
CD, 800/700/650 CDR (read & write), 700/
650MB CD-RW (read
& write), 700/650MB
High Speed CD-RW
(read & write), 700/
650MB Ultra & Ultra+
speed CD-RW (read
& write)
Format Compatibility
• DVD: DVD-ROM,
DVD-Dual, DVDVideo, 3.9G DVD-R,
4.7G DVD-R, DVD+R,
DVD+RW, DVD-RW,
DVD+R dual, DVD-R
dual, DVD-RAM
• CD: CD-DA, CDROM, CD-ROM XA
photo CD, CD-ROM
Multi-Session, CD-I,
CD Plus, CD Extra,
Video-CD, CD-R, CDRW & HSRW Super
Audio CD, US &
US+RW
• DVD: DVD-Video,
DVD-ROM, DVD-R
(3.9GB, 4.7GB), DVDR DL, DVD-RW (Ver.
1.1), DVD-RAM,
DVD+R, DVD+R DL,
DVD+RW, DVD-R
3.9GB (read only),
DVD-RAM 2.6GB
(read only)
• CD: CD-DA, CDROM, CD-ROM XA,
Photo CD (MultiSession), Video CD,
CD-Extra, CD-Text
• DVD (read): DVDROM (DVD-5/9/10/
18), DVD-Video,
DVD-Audio, SACD
(Hybrid), DVD-R,
DVD-R DL, DVD-R
3.95GB, DVD-R
Authoring, DVD-R
Multi-Border, DVDRW, DVD+R, DVD+R
DL, DVD+R MultiSession, DVD+RW,
DVD-RAM V1.0,
DVD-RAM V2.1
• DVD (write): DVD
Data & Video
• CD (read): CD-DA,
CD-ROM Mode-1,
CD-ROM/XA Mode-2
Form-1and Mode-2
Form-2, CD-i, CD-i
Bridge, Enhanced
CD, CD Plus, CDExtra, i-trax CD, CDText, Video-CD
(MPEG1), Karaoke
CD, CD-R, CD-RW
• CD (write): CD-DA,
CD-ROM Mode-1,
CD-ROM/XA Mode-2
Form-1 and Mode-2
Form-2, CD-i, VideoCD, CD-Text
Power requirement
max. 1600mA
max. 1800 mA
max. 2100mA
Input voltage
+5V +/- 5% (Operating)
+5V +/- 0.25V
5V +/- 5% (Operating)
Chapter 1
45
LCD 15.4”
Item
Specification
Vendor & Model name
QDI QD15AL02-01
QDI QD15TL07-01
Screen Diagonal
15.4” WSXGA
15.4” WXGA
Active area
331.2 (W) x 207.0 (H)
331.2 (W) x 207.0 (H)
Display resolution
1680 x 3 (RGB) x 1050
1280 x 3 (RGB) x 800
Display mode
normally white
normally white
Surface treatment
QD15AL02-01 non-glare +
Hardness 3H
QD15TL07-01 non-glare +
Hardness 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
0.1971 (H) x 0.1971 (V)
0.2588 (H) x 0.2588 (V)
200 (typical)
185 (typical)
Contrast ratio
400 (typical)
400 (typical)
Respond time (msec.)
Rise: 6
Decay: 10
Rise: 6
Decay: 10
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Power consumption (watt)
4.38 (typical)
4.38 (typical)
Weight
585g
585g
Physical size (mm)
344.5 (W) x 222.5 (V) x 6.5 (T)
344.0 (H) x 222.0 (V) x 6.35 (T)
Electrical interface
2 channels LVDS
1 channel LVDS
Color support
262,144 colors
262,144 colors
Pixel pitch (mm)
Typical white luminance (cd/m
also called brightness
2)
Item
Specification
Vendor & Model name
CMO
N154I2-L01
Screen Diagonal
15.4” WXGA
15.4” WSXGA
Active area
335.0 (W) x 210.7 (H)
331.2 (W) x 207.0 (H)
Display resolution
1280 x 3 (RGB) x 800
1680 x 3 (RGB) x 1050
Display mode
normally white
normally white
Surface treatment
non-glare + Hard Coating 3H
non-glare + Hard Coating 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
0.2588 (H) x 0.2588 (V)
0.1971 (H) x 0.1971 (V)
Typical white luminance (cd/m )
also called brightness
200 (typical)
185 (typical)
Contrast ratio
400 (typical)
350 (typical)
Respond time (msec.)
Rise: 5
Decay: 11
Rise:4
Decay: 12
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Pixel pitch (mm)
2
46
CMO
N154Z1-L01
Power consumption (watt)
4.2 (typical)
4.2 (typical)
Weight
540g
580g
Physical size (mm)
344.0 (W) x 222.0 (H) x 6.2 (D)
344.0 (W) x 222.0 (H) x 6.2 (D)
Electrical interface
30-pin LVDS interface
LVDS
Color support
262,144 colors
262,144 colors
Chapter 1
LCD 15.4”
Item
Specification
Vendor & Model name
CMO N154C2-L03
AUO B154PW02 V03
Screen Diagonal
15.4” WXGA
15.4” WXGA
Active area
331.56 (H) x 207.225 (V)
331.2 (W) x 207.0 (H)
Display resolution
1440 x 3 (RGB) x 900
1440 x 3 (RGB) x 900
Display mode
normally white
normally white
Surface treatment
anti-glare + hard coating 3H
anti-glare + Hardness 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
0.23025 x 0.23025
0.23025 x 0.23025
Typical white luminance (cd/m )
also called brightness
175 (typical)
250 (typical)
Contrast ratio
400 (typical)
400 (typical)
Respond time (msec.)
Rise: 3
Decay: 7
Rise: 4
Decay: 12
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Pixel pitch (mm)
2
Power consumption (watt)
4.2 (typical)
4.2 (typical)
Weight
530g
535g max.
Physical size (mm)
344.0 (W) x 222.0 (H) x 6.2 (D)
344.0 (W) x 222.0 (H) x 6.1 (D)
Electrical interface
30-pin LVDS interface
2-channel LVDS
Color support
262,144 colors
Item
262,144 colors
Specification
Vendor & Model name
AUO B154EW02-V0
LPL
LP154W01-TLE1
LP154W01-TLE3
Screen Diagonal
15.4” WXGA
15.4” WXGA
Active area
331.2 (W) x 207.0 (H)
331.2 (W) x 207.0 (H)
Display resolution
1280 x 3 (RGB) x 800
1280 x 3 (RGB) x 800
Display mode
normally white
normally white
Surface treatment
anti-glare + hardness 3H
non-glare + Hard Coating 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
Pixel pitch (mm)
0.2588 x 0.2588
0.25875 (H) x 0.25875 (V)
Typical white luminance (cd/m2)
also called brightness
200
200 (typical)
Contrast ratio
400 (typical)
400 (typical)
Respond time (msec.)
Rise: 4
Decay: 12
Rise: 6
Decay: 10
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Power consumption (watt)
4.2 (typical)
4.2 (typical)
Weight
500g
560g
Physical size (mm)
344.0 (W) x 222.0 (H) x 6.1 (D)
344.0 (W) x 222.0 (H) x 6.5 (D)
Electrical interface
1-channel LVDS
LVDS
Color support
262,144 colors
262,144 colors
Chapter 1
47
LCD 15.4”
Item
Specification
Vendor & Model name
SAMSUNG 154P4-L01-0
SAMSUNG 154XA-L01-0
Screen Diagonal
15.4” WXGA
15.4” WXGA
Active area
331.38 (H) x 207.1125 (H)
331.2 (W) x 207.0 (H)
Display resolution
1680 x 3 (RGB) x 1050
1280 x 3 (RGB) x 800
Display mode
normally white
normally white
Surface treatment
anti-glare + hard coating 3H
anti-glare + hard Coating 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
0.19725 (H) x 0.19725 (V)
0.25875 (H) x 0.25875 (V)
Typical white luminance (cd/m )
also called brightness
200
200 (typical)
Contrast ratio
300 (typical)
300 (minimum)
Respond time (msec.)
Rise + Decay: 16
Rise + Decay: 16
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Pixel pitch (mm)
2
Power consumption (watt)
4.2 (typical)
4.2 (typical)
Weight
570g
560g
Physical size (mm)
344.0 (W) x 222.0 (H) x 6.1 (D)
344.0 (W) x 222.0 (H) x 6.1 (D)
Electrical interface
1-channel LVDS
LVDS
Color support
262,144 colors
262,144 colors
LCD 15”
Item
48
Specification
Vendor & Model name
QDI QD150XL06-03-01
LPL LP150X08-TLA2
Screen Diagonal
15” XGA
15” XGA
Active area
304.13 (W) x 228.1 (H)
304.128 (W) x 228.096 (H)
Display resolution
1024 x 3 (RGB) x 768
1024 x 3 (RGB) x 768
Display mode
normally white
normally white
Surface treatment
glare + Hardness 3H
non-glare + Hard Coating 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
Pixel pitch (mm)
0.297 (H) x 0.297 (V)
0.297 (H) x 0.297 (V)
Typical white luminance (cd/m2)
also called brightness
160 (typical)
170 (typical)
Contrast ratio
300 (typical)
250 (typical)
Respond time (msec.)
Rise: 8 Decay: 17
Rise: 10 Decay: 20
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Power consumption (watt)
3.96 (typical)
4.76 (typical)
Weight
570g
530g
Physical size (mm)
317.3 (W) x 242.0 (H) x 5.9 (D)
317.3 (W) x 241.5 (H) x 5.9 (D)
Electrical interface
1 channel LVDS
LVDS
Color support
262,144 colors
262,144 colors
Chapter 1
LCD 15”
Item
Specification
Vendor & Model name
CMO N150X3-L9
AUO B150XG02 V4
Screen Diagonal
15” XGA
15” XGA
Active area
304.1 (W) x 228.1 (H)
304.1 (W) x 228.1 (H)
Display resolution
1024 x 3 (RGB) x 768
1024 x 3 (RGB) x 768
Display mode
normally white
normally white
Surface treatment
non-glare + Hard Coating 3H
non-glare + Hardness 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
0.297 (H) x 0.297 (V)
0.297 (H) x 0.297 (V)
Typical white luminance (cd/m )
also called brightness
200 (typical)
170 (typical)
Contrast ratio
250 (typical)
300 (typical)
Respond time (msec.)
Rise: 5 Decay: 11
Rise: 16 Decay: 9
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Power consumption (watt)
3.96 (typical)
3.9 (typical)
Weight
550g
585g
Physical size (mm)
317.3 (W) x 242 (H) x 5.7 (D)
317.3 (W) x 242 (H) x 5.7 (D)
Electrical interface
LVDS
1 channel LVDS
Color support
262,144 colors
Pixel pitch (mm)
2
Item
262,144 colors
Specification
Vendor & Model name
AUO B150PG03 V0
SAMSUNG LTN150XB-L03-V
Screen Diagonal
15” SXGA
15” XGA
Active area
304.5 (W) x 228.375 (H)
304.128 (H) x 228.096 (V)
Display resolution
1400 x 3 (RGB) x 1050
1024 x 3 (RGB) x 768
Display mode
normally white
normally white
Surface treatment
non-glare + Hardness 3H
Haze 25, Hard coating 3H
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
Pixel pitch (mm)
0.2175 (H) x 0.2175 (V)
0.297 (H) x 0.297 (V)
Typical white luminance (cd/m2)
also called brightness
200 (typical)
160 (typical)
Contrast ratio
300 (typical)
200 (minimum)
Respond time (msec.)
Rise: 16 Decay: 9
Rise: 10 Decay: 30
Normal input voltage of power
supply
+3.3V (typical)
+3.3V (typical)
Power consumption (watt)
5.9W
4.26W
Weight
575g
585g
Physical size (mm)
317.3 (W) x 242.0 (H) x 6.5 (D)
317.8 (W) x 242.6 (H) x 6.5 (D)
Electrical interface
2-channel LVDS
3.3V LVDS
Color support
262,144 colors
262,144 colors
Chapter 1
49
Battery
Item
Specification
Model
SONY LIP8216IVPC PACK 4800 mAh 8
CELL
SONY LIP6219IVPC PACK 4000mAh 6
CELL
Rating
Specification
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Nominal capacity: 4800 mAh
Nominal voltage: 14.8V
Rated charge voltage: 16.8V
Discharge cutoff voltage: 12.0V
Rated charge current: 3.84A
Discharge loading: 10W ~ 78W
Max. discharge current: 6.5A
Inrush current 30A (0.4mS)
• Discharge cell temperature: -20oC ~
70oC
• Discharge cell temperature: -20oC ~
70oC
• Initial charge temperature: 0oC ~ 50oC
• Initial charge temperature: 0oC ~ 50oC
• Charge continuous temperature: 0
60oC
Charge
specification
Environment
oC
~
• Charge continuous temperature: 0oC ~
60oC
• Charge voltage: 16.8A
• Charge current: 3.84A
• Charge voltage: 12.6V
• Charge current: 3.2A
• Charge initial temperature: 0oC ~ 50oC
• Charge method: CC-CV mode
• Charge initial temperature: 0oC ~ 50oC
• Charge mode: CC-CV mode
• Charge suspension: < 0oC or 60oC >;
Charging current = 0; Bad battery;
Communication lost
• Charge suspension: < 0oC or 60oC >;
Charging current = 0; Bad battery;
Communication lost
• Charging time: 150 min. (25oC ~ 40oC);
180 mins. (5oC)
• Charging time: 150 mins. (25oC ~ 40oC);
180 mins. (5oC)
• Storage temperature range: max. 1
month (-20oC ~ 60oC); max. 3 months
(-20oC ~ 45oC); max. 6 months (-20oC ~
30oC)
• Humidity: 10% ~ 90% RH
• Storage temperature range: max. 1
month (-20oC ~ 60oC); max. 3 months
(-20oC ~ 45oC); max. 6 months (-20oC ~
30oC)
• Humidity: 10% ~ 90% RH
Item
Specification
Model
SANYO 4UR18650F-2-INV-6 4800mAh 8
CELL
SANYO 3UR18650Y-2-INV-10 4000mAh
6 CELL
Nominal
specification
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
50
Nominal capacity: 4000 mAh
Nominal voltage: 11.1V
Rated charge voltage: 12.6V
Discharge cutoff voltage 9.0V
Rated charge current 3.2A
Discharge loading: 10W ~ 67W
Max. discharge current: 6.0A
Inrush current: 30A (0.4mS)
Nominal capacity: 4600mAh
Typical capacity: 4800mAh
Nominal voltage: 14.8V
End voltage: 12.0V
Charging voltage: 3840mA (typical);
4080mA (max.)
Charging voltage: 16.80+/-0.12V (CCCV charge mode)
Charging time (standard): 3.0 hours at
25oC
Max. discharging loading: 92W
Max. internal resistance: 185 mOmega
Max. weight: 420g
•
•
•
•
•
Nominal capacity: 3800mAh
Typical capacity: 4000mAh
Nominal voltage: 11.1V
End voltage: 9.0V
Charging current: 3200mA (typical);
3400mA (max.)
Charging voltage: 12.6+/-0.09V (CC-CV
charge mode)
Charging time (standard): 3.0 hours at
25oC
Max. discharging loading: 67W
Max. internal resistance: 178 mOmega
Max. weight: 330g
Chapter 1
Item
Specification
Environment
• Storage temperature range: max. 1
month (-20oC ~ 60oC); max. 3 months
(-20oC ~ 45oC); max. 12 months (-20oC
~ 25oC)
• Storage temperature range: max. 1
month (-20oC ~ 60oC); max. 3 months
(-20oC ~ 45oC); max. 12 months (-20oC
~ 25oC)
AC Adaptor
Item
Specification
Feature
• Normal AC adaptor, 90 ~ 264V AC, 47 ~ 63Hz
• 3-pin 90W with 19V DC output
• Normal DC jack (diameter 1.7 mm)
System Fan True Value Table
Test Condition: 35W@ambient 25ʚ
CPU Temperature
Chapter 1
Fan Speed
Acoustic
DTS_0
DTS_1
(RPM)
(dBA)
85
85
4000
43
86
86
3800
40
88
88
3500
38
92
92
3100
34
94
94
2700
31
51
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output
System). Your computer is already properly configured and optimized, and you do not need to run this utility.
However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted on
the bottom of screen). The setup screen displays BIOS as follows:
Function
Item
Information
Display the system informations
Main
Allows the user to specify standard IBM PC AT system
parameters
Advanced
Provides advanced settings of the system
Security
Provides security settings of the system
Boot
Allows the user to specify the boot options
Exit
Allows the user to save CMOS setting and exit Setup
During setup, all Fn function keys and power saving functions are disabled. There are five menu options: Main,
Advanced, Security, Boot and Exit. Follow these instructions below
•
To choose a menu, use the cursor left/right keys (zx).
•
To choose a parameter, use the cursor up/down keys (wy).
•
To change the value of a parameter, press p or q.
•
Press ^ while you are in any of the menu options to go to the Exit menu.
•
In any menu, you can load default settings by pressing t. You can also press u to save any changes
made and exit the BIOS Setup Utility.
Note: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific
Help part of the screen. Read this carefully when making changes to parameter values.
Chapter 2
52
Information
Parameter
53
Description
CPU Type
This item will show the CPU information of the system.
CPU Speed
This item will show the CPU clock speed.
IDE1 Model Name
This item will show the Model name of HDD installed on Primary IDE master.
The hard disk model name is automatically detected by the system. If there is no
hard disk present or unknown type, “None” should be shown on this field
IDE1 Serial Number
This item will show the Serial number of HDD installed on Primary IDE master. If
no Hard disk or other devices are installed on Primary IDE master, then it will
display a blank line
System BIOS Version
This field reports the BIOS version of system
VGA BIOS Version
This field reports the VGA version of the system
KBC Version
This field reports the keyboard controller version of the system
Serial Number
This item will show the Serial number of system.
Asset Tag Number
This item will show the Asset Tag number of the system.
Product Name
This field will show product name.
Manufacturer Name
This field will show manufacturer name.
UUID
This will be visible only when there is an internal LAN device present.
Chapter 2
Main
Parameter
Description
System Time / System
Date
The hours are displayed with 24 hours format. The values set in these two fields
take effect immediately.
System Memory
This field reports the memory size of system base memory. The size is fixed to
640KB.
Extended Memory
This field reports the memory size of the extended memory in the system.
Extended Memory size = Total memory size - 1 MB
Video Memory
VGA Memory size = 128MB
Quiet Boot
Customer Logo display will be shown during POST when it is selected.
Power on display
Auto: During power on process, the system will detect if any display device is
connected on external video port. If any external display device is connected,
the power on display will be in CRT (or projector) only mode. Otherwise it will be
in LCD only mode.
Both: Simultaneously enable both the integrated LCD screen and the system’s
external video port (for an external CRT or projector).
Network boot
When this is selected, Boot from LAN feature is enabled. When this is not
selected, Boot from LAN feature is then disabled.
F12 Boot Menu
When this is selected, users can modify device boot priority by pressing F12 key
during POST. When this is not selected, device boot priority will not be
adjustable during POST.
D2D Recovery
Allow user to enable/disable the Disk-to-Disk recovery
Chapter 2
54
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
Parameter
55
Description
Option
Serial Port
Configure serial port A using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayed when controlled by OS
Disabled
Enabled
Auto
Infrared Port
Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayed when controlled by OS
Disabled
Enabled
Auto
Parallel Port
Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayed when controlled by OS
Disabled
Enabled
Auto
Mode
Set the mode for the parallel port
Output only
Bi-directional
EPP
ECP
Chapter 2
Security
The system supports three levels of password protection. The password support consists of a Supervisor
Password, User Password, and Hard Disk Password. All the passwords are stored in a non-volatile storage device
(EEPROM).
All the passwords obeys the following rules:
•
Password Policy
•
All the passwords can be set or cleared in BIOS Setup Security screen.
•
The password entry consists of eight alphanumeric characters. At least one character must be
assigned.
•
The valid keys are listed in the table below:
Symbol Character
Chapter 2
Symbol Name
A-Z
letters A to Z (not case sensitive)
0-9
numerical characters
-
dash
=
equal sign
[
left bracket
]
right bracket
.
period
,
comma
;
semi-colon
56
Symbol Character
•
•
•
57
Symbol Name
/
slash
\
back slash
•
The users can not change or remove password during resuming from S4.
•
The max. number of times to retry the password is limited to three.
Supervisor Password:
•
Supervisor Password controls the access of the whole BIOS Setup Utility. If the Supervisor Password
is set, the system will pop up the password dialog box to ask for the password when the users press
<F2> for entering BIOS Setup Utility.
•
If the Supervisor Password is set and Password on boot is enabled, the system will pop up the
password dialog box to ask for the password when the system is powered on or resumes for S4 state.
•
If the users fail three times consecutively in password verification, the system will be hung up and the
users need to manually power off the system.
User Password:
•
If the User Password is set, the system will pop up the password dialog box to ask for the password
when the users press <F2> for entering BIOS Setup Utility.
•
If the Supervisor Password is not set at first, the User Password can not be set. If the Supervisor
Password is cleared, the User Password will be cleared, too.
•
If the User Password is set and Password on boot is enabled, the system will pop up the password
dialog box to ask for the password when the system is powered on or resumes for S4 state.
•
If the users fail three times consecutively in password verification, the system will be hung up and the
users need to manually power off the system.
Set Supervisor Password / User Password:
•
Highlight the item and press “Enter”, a dialog box will be shown to ask the users to enter new
password and confirm new password.
•
If the users want to reset password, a current password will be required to be tapped in at first. If the
current password is correct, the users are permitted to enter new password and confirm new
password for verification. If the verification is OK, the password setting will be complete after the users
press “Enter”.
•
If the password entered does not match the current password, a dialog box will be shown to ask to reenter the password.
•
Set HDD Password: When shown as “Locked”, the hard drive password currently can not be changed or
disabled. To change or disable it, turn off the system and enter Setup immediately after turning it back on.
Press “Enter” to input change, or disable hard drive password.
•
Password on Boot: It allows the user to specify whether or not a password is required to boot.
Chapter 2
Boot
This menu allows the users to decide the order of bootable devices to load the operating system. It identifies all the
bootable devices in the system and attempts to boot them in the order specified. Bootable devices include the
diskette drive in module bay, the hard disk and the CD-ROM/DVD drive in module bay and onboard LAN device.
Parameter
Boot priority order
Chapter 2
Description
Keys used to view or configure devices: Up and Down arrows select a device.
<+> and <-> move the device up or down. <f> and <r> specifies the device fixed
or removable. <x> exclude or include the device to boot. <Shift +1> enables or
disables a device. <1-4> Loads default boot sequence.
58
Exit
Parameter
59
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS
Exit Discarding
Changes
Exit utility without saving Setup data to CMOS
Load Setup Default
Load default values for all SETUP items
Discard Changes
Load previous values from CMOS for all SETUP items
Save Changes
Save Setup Data to CMOS
Chapter 2
Chapter 3
Machine Disassembly and Replacement
General Information
This chapter contains step-by-step procedures on how to disassemble the Aspire 6460/6410 for maintenance and
troubleshooting.
To disassemble the notebook, you need the tools below:
•
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Flat headed screw driver
•
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components. When you
remove the stripe cover, please be careful not to scrape the cover.
Before You Begin
Before proceeding with the disassembly procedure, you have to make sure that:
•
The system and all peripherals are powered off.
•
The AC adaptor and all power and signal cables from the system are unplugged.
•
The battery pack is removed.
Note: There are several types of screws used to secure the main unit. The screws vary in length. Please refer
to the screws table after the flowchart. Group the same type of screws together during service disassembling.
Please also remember the screw location for each screw type. If you fasten the screws on the wrong location,
the long screws may cause irrecoverable damage to the main board.
Chapter 3
60
Disassembly Procedure Flowchart
The flowchart gives you a graphic representation on the entire disassembly and reassembly and instructs you how
to remove the components.
#
61
Description
Acer Part No.
al
SCREW-I20040M-BK-PATCH
86.TCXVN.001
b
SCREW-I25025M (4.5Dx0.8T) -BK-PATCH
86.TCXVN.002
c
SCREW-I250100M (4.5DX0.8T) -BK-PATCH
86.TCXVN.003
d
SCREW-I20050M (4.5Dx0.5T) -BK-PATCH
86.TCXVN.004
e
SCREW-I25040M (4.5Dx0.8T) -BK-PATCH
86.TCXVN.005
f
SCREW-I-M2.0-3.0-M-4.0Dx0.3T-BK-PATCH
86.TCXVN.006
g
SCREW, I, M2.5, 3.0mm, M, 4.5mm, 0.8mm, BNI, PAT
86.TCXVN.007
h
SCREW, I, M2.5, 5mm, M, 0.45mm, 0.8mm, BNI, PATC
86.D03VN.004
i
SCREW-WI30030M (5.0Dx1.5T) -NI-HARDEN
86.AAMVN.001
j
SCREW-I25060M (4.5Dx0.8T) -BK-PATCH
86.AAMVN.002
Chapter 3
Disassembly Procedure
Removing Battery Pack
1. Unlock the battery lock to the end as the arrow indicates.
2. Slide the battery latch to the end as the arrow indicates and hold it. The battery pack will pop up then remove
the battery pack.
Removing HDD Module
1. Release the two screws fastening the HDD module cover then detach the HDD module cover.
2. Pull the HDD module backwards as the arrow indicates then detach the HDD module.
Chapter 3
62
Removing RAM Modules and Mini PCI Card
1. Release the two screws holding the RAM modules and mini PCI card cover then remove the cover.
2. Disconnect the wireless LAN antennae. Release the two screws holding the mini PCI card then detach the mini
PCI card as the arrow indicates.
3. Press the RAM module locks at the same time as the arrows indicate. The RAM module will pop up then
detach the RAM module. Repeat this step to detach another RAM module.
63
Chapter 3
Removing Optical Disk Drive and PCMCIA
1. Push the optical disk drive latch forwards to bring out the optical disk drive.
2. Remove the optical disk drive.
3. Push the PCMCIA eject button to bring out the PCMCIA. Then detach the PCMCIA. When you do the
assembly, at first you have to push the eject button to the end then insert the PCMCIA into the slot.
Chapter 3
64
Removing Keyboard
1. Release the four screws holding the middle cover, two on the rear side and the other two on the bottom side.
2. Then detach the middle cover.
3. Release the two screws fastening the keyboard plate.
4. Detach the keyboard plate slightly then have it reversed as shown.
5. Slightly release the keyboard plate FFC latch with the nail then disconnect that FFC.
6. Slightly release the point device FFC latch then disconnect that FFC. Keep in mind that these two latches are
fragile.
7. Then remove the keyboard plate.
65
Chapter 3
Removing Power Board and Modem Board
1. Release the two screws fastening the power board then detach it from the main unit.
2. Release the two screws holding the modem board. Disconnect the modem board cable then detach the
modem board from the main unit.
Chapter 3
66
Removing LCD module from Main Unit
1. Disconnect the LCD module cable and slightly pull out the wireless LAN antennae.
2. Then disconnect the RJ-11 port cable.
3. Hold the top edge of LCD module and release the four screws holding the LCD module on the main unit.
4. Remove the LCD module from the main unit.
5. When you do the assemble, remember to have the ground wire locked on the LCD left hinge.
67
Chapter 3
Separating Upper Case and Lower Case
1. Carefully release the touch pad board FFC lock then disconnect the touch pad board FFC.
2. Slightly disconnect the microphone cable connector.
3. Release the 16 screws securing the upper case and the lower case on the bottom side.
4. Then detach the upper case from the main unit.
Chapter 3
68
Removing Main Board
1. Disconnect the right and the left speaker cables.
2. Release the DC-in board FFC latch then disconnect the DC-in board FFC.
3. Release the two screws fastening the main board.
4. Detach the main board from edge of the lower case carefully for not causing irreversible damage. Then remove
the main board from the lower case as the arrow indicates.
5. Release the screw holding the DC-in board then detach the DC-in board from the lower case.
69
Chapter 3
Removing Thermal Module
1. Disconnect the CPU fan cable.
2. Release the three screws fastening the thermal module.
3. Remove the thermal module holder then detach the thermal module.
Detaching CPU
1. Release the CPU socket lock by turning a flat headed screw driver counter clockwise.
2. Keep in mind that CPU pins are fragile so please carefully detach the CPU from the socket with tips of fingers.
Chapter 3
70
Removing Touch Pad Board
1. Release the FFC latches then disconnect the following FFCs in sequence as shown: 1) click button board to
touch pad board FFC; 2) stick point board to main board FFC; 3) click button board to stick point board FFC; 4)
the other end of click button board to stick point board FFC.
2. Release the eight screws holding the touch pad board bracket then remove the touch pad board bracket.
3. Remove the touch pad board.
4. Remove the stick point board.
5. Release the two screws holding the click button board then remove the click button board.
71
Chapter 3
Removing LCD Bezel
Note: Please do not press the LCD panel through the whole procedure when you disassemble the LCD
module.
1. Detach the mylars and the rubber cushions covered on the screws then release the four screws securing the
LCD bezel.
2. Carefully detach the LCD bezel from the LCD module as shown till the LCD bezel is total removed.
Chapter 3
72
Removing Inverter Board
1. Release the screw holding the inverter board.
1. Carefully disconnect the backlight cable.
2. Carefully disconnect the LCD cable then remove the inverter board.
Detaching LCD Panel
1. Release the six screws securing the LCD panel.
2. Then detach the LCD panel from the LCD cover.
73
Chapter 3
Removing LCD Brackets
1. Release the four screws securing the left and the right LCD brackets.
2. Then remove the left and the right LCD brackets.
Removing LCD Cable
1. Slight tear off the tape holding the LCD cable connector then disconnect the LCD cable connector.
Chapter 3
74
Chapter 4
Troubleshooting
Please use the following procedures as a guide for computer problems.
Note: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options may occur errors or invalid responses.
1. Obtain the detailed fail symptoms as many as possible.
2. Verify the symptoms by attempting to recreate, running the diagnostic tests or repeating the same operation.
Chapter 4
75
System Check Procedures
External Diskette Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or diskette. A writable,
diagnostic diskette is required.
Note: Make sure that the diskette does not have more than one label attached. Multiple labels may cause
damage to the drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if FDD test is passed as the programs run the FDD test.
3. Follow the instructions in the message window.
If errors occur with the internal diskette driver, reconnect the diskette connector on the system board. If the errors
still remain:
1. Reconnect the external diskette drive.
2. Replace the external diskette driver.
3. Replace the main board.
External CD-ROM Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or CD-ROM.
Note: Make sure that the CD-ROM does not have any label attached. The label may cause damage to the
drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if CD-ROM test is passed when the programs run the CD-ROM test.
3. Follow the instructions in the message window.
If errors occur, reconnect the connector on the system board. If the errors still remain:
1. Reconnect the external CD-ROM drive.
2. Replace the external CD-ROM drive.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is under test. If the internal keyboard does not work or an
unexpected error appears, make sure that the flexible cable extending from the internal keyboard is correctly
connected on the system board. If the keyboard is correctly connected, run the Keyboard test.
If errors occur, do the following procedures in sequence to correct the problems. Do not replace a non-defective
FRU.
1. Reconnect the keyboard cable.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer.
•
Numeric keypad
•
External keyboard
If any of these devices do not function, reconnect the cable and repeat the anterior procedures.
Memory Check
Follow the procedures below to correct the memory errors.
1. Boot from the diagnostic diskette and start the diagnostic programs.
76
Chapter 4
2. Go to the diagnostic memory in the test items.
3. Press F2 in the test items.
4. Follow the instructions in the message window.
Note: Make sure that the DIMM is correctly inserted into the connector. A wrong connection will cause errors.
Power System Check
To verify the symptoms, power on the computer by using the following power sources separately.
1. Remove the battery pack.
2. Connect the power adaptor and check the power supply.
3. Disconnect the power adaptor and install the battery pack, then check the power supply.
If you think there is a power supply problem, please go to Check the Power Adaptor and Check the Battery
Pack in this chapter.
Check the Power Adaptor
Unplug the power adaptor cable from the computer and measure the output voltage at the plug of the power
adaptor cable. See the illustration and follow the procedures below.
pin 1: +19V to +20.5V
pin 2: 0V, ground
1. If the voltage is not correct, replace the power adaptor.
2. If the voltage is within the range:
(1) Replace the system board.
(2) If the problem is still not resolved, see Undetermined Problems.
(3) If the voltage is not correct, go to the next step.
Note: An audible noise from the power adaptor does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adaptor for continuity and correct
installation.
4. If the operational charge does not work, see Check the Battery Pack.
Check the Battery Pack
Follow the procedures below to check the battery pack.
From software, this helps to identify the problem is on recharging or discharging.
1. Check the Power Management in Control Panel.
2. Then confirm that the parameters shown in the screen for Current Power Source and Total Battery Power
Remaining are correct.
3. Repeat the step 1 and step 2 for both battery and adaptor.
From hardware, this helps to identify whether you should replace the battery pack or not.
1. Power off the system.
2. Remove the battery pack and measure the voltage between terminals one (+) and seven (-). There are seven
terminals totally. See the illustration below.
3. If the voltage is still less than 7.5V after recharging, replace the battery.
If the battery status indicator does not light up, remove the battery pack. After the battery pack returns to room
temperature, reinstall it to the system.
Chapter 4
77
If the charge indicator does not light up, replace the battery pack. If the charge indicator still does not light up,
replace the AC / DC charger board.
Touchpad Check
If the touchpad does not work, follow the procedures one at a time to correct the problem. Do not replace a nondefective FRU.
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement will
occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem.
78
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes.
Note: Perform the FRU replacement or actions in the sequence shown in Error Message List, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
The error messages are listed in the coming pages to indicate the BIOS signals on the screen and the error
symptoms classified by functions. If the symptom is not included on the list, please refer to Undetermined
Problems.
Note: Most of the error messages occur during POST. Some of them show information about a hardware
device, for example, the size of memory installed. Others may indicate problems with a device, such as the
way it has been configured.
Note: If the system fails after you make changes in the BIOS Setup Utility menus, please reset the computer.
Enter Setup and install Setup defaults to correct the errors.
Index of Error Messages
Error Code List
Error Code
Error Message
006
Equipment Configuration Error Causes:
• CPU BIOS Update Code Mismatch
• IDE Primary Channel Master Drive Error
The causes will be shown before Equipment Configuration Error.
010
Memory Error at xxxx:xxxx:xxxxh (R: xxxxh, W: xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
No error code
Battery critical low: In this situation BIOS will issue four short beeps then
shut down system, no message will be shown.
No error code
Thermal critical high: In this situation BIOS will shut down the system, no
message will be shown.
Error Message List
Error Message
FRU/Action in Sequence
Failure Fixed Disk
Reconnect hard disk drive connector.
Run Load Default Settings in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see Keyboard or Auxiliary Input Device Check.
Keyboard error
see Keyboard or Auxiliary Input Device Check.
Keyboard Controller Failed
see Keyboard or Auxiliary Input Device Check.
Keyboard locked - Unlock key
switch
Unlock external keyboard
Monitor type does not match
CMOS - Run Setup
Run Load Default Settings in BIOS Setup Utility.
Chapter 4
79
Error Message
80
FRU/Action in Sequence
Shadow RAM Failed at offset:
nnnn
BIOS ROM
System board
System RAM Failed at offset:
nnnn
DIMM
System board
Extended RAM Failed at offset:
nnnn
DIMM
System board
System battery is dead Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to
reconfigure system time, then reboot system.
System CMOS checksum bad Default configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Previous boot incomplete Default configuration used
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST
differed from CMOS
Run Load Default Settings in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in
BIOS Setup Utility.
See External Diskette Drive Check.
Incorrect Drive A type - run
Setup
Check the drive is defined with the proper diskette type in
BIOS Setup Utility.
System cache error - Cache
disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Chapter 4
Error Message
FRU/Action in Sequence
Invalid System Configuration
Data
BIOS ROM
System board
I/O device IRQ conflict
Run Load Default Settings in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly
identified.
Diskette drive
Hard disk drive
System board
No beep, power-on indicator
turns off and LCD is blank.
Power source (battery pack and power adapter). See
Power System Check.
Ensure every connector is connected correctly.
Reconnect the DIMM.
LED board
System board
No beep, power-on indicator
turns on and LCD is blank.
Power source (battery pack and power adapter). See
Power System Check.
Reconnect the LCD connector.
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator
turns on and LCD is blank. But
you can see POST on an
external CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator
turns on and a blinking cursor
shown on LCD during POST.
Ensure every connector is connected tightly and correctly.
System board
No beep during POST but
system runs correctly.
Speaker
System board
Chapter 4
81
Phoenix BIOS Beep Codes
Beep Code
82
Post Code
Description
What to Check (Recommended)
1-1-1-3
02h
Verify Real Mode.
• Check the processor.
• Check the main board.
1-1-2-1
04h
Get CPU type.
• Check the processor.
• Check the main board.
1-1-2-3
06h
Initialize system hardware.
• Check the main board.
1-1-3-1
08h
Initialize cache to initial
POST values.
• Check the main board.
1-1-3-2
09h
Set in POST flag.
• Check the main board.
1-1-3-3
0Ah
Initialize CPU registers.
• Check the processor.
• Check the main board.
1-1-4-1
0Ch
Initialize cache to initial
POST values.
• Check the secondary cache.
• Check the processor.
• Check the main board.
1-1-4-3
0Eh
Initialize I/O.
• Make sure all the cards are securely
inserted into the system.
• Make sure that there are no physical
problems with the main board or
internal connections.
• Disable all shadowing of expansion
adapter ROMs and see if that fixes the
problem.
• Remove all unnecessary expansion
cards (basically, everything but the
video card) and see if the problem
goes away. If it does, the problem is
probably one of the expansion cards
you removed. If not, your problem lies
elsewhere. Try to isolate the problem
by inserting one expansion card at a
time back into the system and seeing
which on e triggers the problem.
1-2-1-1
10h
Initialize Power
Management.
• Check the main board.
1-2-1-2
11h
Load alternate registers
with initial POST values.
• Check the main board.
1-2-1-3
12h
Jump to UserPatch0.
• Check the main board.
1-2-2-1
14h
Initialize keyboard
controller.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
1-2-2-3
16h
BIOS ROM checksum.
• Check the main board.
1-2-3-1
18h
8254 timer initialization.
• Check the main board.
1-2-3-3
1Ah
8237 DMA controller
initialization
• Treat as an expansion card problem.
• Check the main board.
1-2-4-1
1Ch
Reset Programmable
Interrupt Controller
• Treat as an expansion card problem.
• Check the main board.
1-3-1-1
20h
Test DRAM refresh.
• Check the system memory.
• Check the main board.
Chapter 4
Beep Code
Post Code
Description
What to Check (Recommended)
1-3-1-3
22h
Test 8742 keyboard
controller.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
1-3-2-1
24h
Set ES segment register to
4GB.
• Check the main board.
1-3-3-1
28h
Autosize DRAM.
• Check the system memory.
• Check the main board.
1-3-3-3
2Ah
Clear 512K base RAM.
• Check the system memory.
• Check the main board.
1-3-4-1
2Ch
RAM failure on address
line xxxx.
• Check the system memory.
• Check the main board.
1-3-4-3
2Eh
RAM failure on data bits
xxxx of low byte of memory
bus.
• Check the system memory.
• Check the main board.
1-4-1-3
32h
Test CPU bus-clock
frequency.
• Check the processor.
• Check the main board.
1-4-2-1
34h
COMS RAM read/write
failure.
• Check the main board.
1-4-2-4
37h
Reinitialize the chipset.
• Check the main board.
1-4-3-1
38h
Shadow system BIOS
ROM.
• Check the expansion cards.
• Check the system memory.
• Check the main board.
1-4-3-2
39h
Reinitialize the cache.
• Check the secondary cache.
• Check the processor.
• Check the main board.
1-4-3-3
3Ah
Autosize cache.
• Check the secondary cache.
• Check the processor.
• Check main board.
1-4-4-1
3Ch
Configure advanced
chipset registers.
• Check the main board.
1-4-4-2
3Dh
Load alternate registers
with CMOS values.
• Check the main board.
2-1-1-1
40h
Set Initial CPU speed.
• Check the main board.
2-1-1-3
42h
Initialize interrupt vector.
• Treat as an expansion card problem.
• Check the main board.
2-1-2-1
44h
Initialize BIOS interrupt.
• Treat as an expansion card problem.
• Check the main board.
2-1-2-3
46h
Check ROM copyright
notice.
• Check the main board.
2-1-2-4
47h
Initialize manager for PCI
Options ROMs.
•
•
•
•
2-1-3-1
48h
Check video configuration
against CMOS.
• Check the video card.
• Make sure the system memory is
working properly.
• Check the main board.
Chapter 4
Treat as an expansion card problem.
Check the serial port(s).
Check the parallel port(s).
Check the main board.
83
Beep Code
84
Post Code
Description
What to Check (Recommended)
2-1-3-2
49h
Initialize PCI bus and
devices.
•
•
•
•
Treat as an expansion card problem.
Check the serial port(s).
Check the parallel port(s).
Check the main board.
2-1-3-3
4Ah
Initialize all video adapters
in system.
• Check the video card.
• Make sure the system memory is
working properly.
2-1-4-1
4Ch
Shadow video BIOS ROM.
• Check the expansion cards.
• Check the system memory.
• Check the main board.
2-1-4-3
4Eh
Display copyright notice.
• Check the video card.
• Check the main board.
2-2-1-1
50h
Display CPU type and
speed.
• Check the video card.
2-2-1-3
52h
Test keyboard.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
2-2-2-1
54h
Set key click if enabled.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
2-2-2-3
56h
Enable keyboard.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
2-2-3-1
58h
Test for unexpected
interrupts.
• Treat as an expansion card problem.
• Check the main board.
2-2-3-3
5Ah
Display prompt “Press F2
to enter SETUP”.
• Check the video card.
• Check the main board.
2-2-4-1
5Ch
Test RAM between 512
and 640K.
• Check the system memory.
• Check the main board.
2-3-1-1
60h
Test expanded memory.
• Check the system memory.
• Check the main board.
2-3-1-3
62h
Test extended memory
address lines.
• Check the system memory.
• Check the main board.
2-3-2-1
64h
Jump to UserPatch1.
• Check the main board.
2-3-2-3
66h
Configure advanced cache
registers.
• Check the secondary cache.
• Check the processor.
• Check the main board.
2-3-3-1
68h
Enable external and CPU
caches.
• Check the secondary cache.
• Check the processor.
• Check the main board.
2-3-3-2
69h
Initialize SMI handler.
• Check the main board.
2-3-3-3
6Ah
Display external cache
size.
• Check the video card.
• Check the main board.
2-3-4-1
6Ch
Display shadow message.
• Check the video card.
• Check the main board.
2-3-4-3
6Eh
Display non-disposable
segments.
• Check the video card.
• Check the main board.
Chapter 4
Beep Code
Post Code
Description
What to Check (Recommended)
2-4-1-1
70h
Display error messages.
• Check the video card.
• Check the main board.
2-4-1-3
72h
Check for configuration
errors.
• Check the main board.
2-4-2-1
74h
Test real-time clock.
• Check the main board.
2-4-2-3
76h
Check for keyboard errors.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
2-4-4-1
7Ch
Set up hardware interrupts
vectors.
• Treat as an expansion card problem.
• Check the main board.
2-4-4-3
7Eh
Test coprocessor if
present.
• Check the processor.
• Check the main board.
3-1-1-1
80h
Disable onboard I/O ports.
•
•
•
•
Treat as an expansion card problem.
Check the serial port(s).
Check the parallel port(s).
Check the main board.
3-1-1-3
82h
Detect and install external
RS232 ports.
•
•
•
•
Treat as an expansion card problem.
Check the serial port(s).
Check the parallel port(s).
Check the main board.
3-1-2-1
84h
Detect and install external
parallel ports.
•
•
•
•
Treat as an expansion card problem.
Check the serial port(s).
Check the parallel port(s).
Check the main board.
3-1-2-3
86h
Reinitialize onboard I/O
ports.
•
•
•
•
Treat as an expansion card problem.
Check the serial port(s).
Check the parallel port(s).
Check the main board.
3-1-3-1
88h
Initialize BIOS data area.
• Check the main board.
3-1-3-3
8Ah
Initialize extended BIOS
data area.
• Check the main board.
3-1-4-1
8Ch
Initialize floppy controller.
• Check the HDD.
• Check the floppy disk drive(s).
• Check the main board.
3-2-1-1
90h
Initialize hard disk
controller.
• Check the HDD.
• Check the floppy disk drive(s).
• Check the main board.
3-2-1-2
91h
Initialize local bus hard
disk controller.
• Check the HDD.
• Check the floppy disk drive(s).
• Check the main board.
3-2-1-3
92h
Jump to UserPatch2.
• Check the main board.
3-2-2-1
94h
Disable A20 address line.
• Check the keyboard.
• Check keyboard controller.
• Check the main board.
3-2-2-3
96h
Clear huge ES segment
register.
• Check the main board.
3-2-3-1
98h
Search for option ROMs.
• Check the main board.
Chapter 4
85
Beep Code
86
Post Code
Description
What to Check (Recommended)
3-2-3-3
9Ah
Shadow for option ROMs.
• Check the expansion cards.
• Check the system memory.
• Check the main board.
3-2-4-1
9Ch
Set up Power
Management.
• Check the main board.
3-2-4-3
9Eh
Enable hardware
interrupts.
• Treat as an expansion card problem.
• Check the main board.
3-3-1-1
A0h
Set time of day.
• Check the main board.
3-3-1-3
A2h
Check key lock.
• Unlock the key lock if it is locked.
• Investigate possible problem with the
key lock switch. If it is either unlocked
already or not present on the system
case.
• Check the main board.
3-3-3-1
A8h
Erase F2 prompt.
• Check the video card.
• Check the main board.
3-3-3-3
AAh
Scan for F2 key stroke.
• Check the main board.
3-3-4-1
ACh
Enter SETUP.
• Check the main board.
3-3-4-3
AEh
Clear in-POST flag.
• Check the main board.
3-4-1-1
B0h
Check for errors.
• Check the main board.
3-4-1-3
B2h
POST done - prepare to
boot operating system.
• Check the main board.
3-4-2-1
B4h
One beep.
• Check the main board.
3-4-2-3
B6h
Check password
(optional).
• Check the main board.
3-4-3-1
B8h
Clear global descriptor
table.
• Check the main board.
3-4-4-1
BCh
Clear parity checkers.
• Check the main board.
3-4-4-3
BEh
Clear screen (optional).
• Check the video card.
• Check the main board.
3-4-4-4
BFh
Check virus and backup
reminders.
• Check the main board.
4-1-1-1
C0H
Try to boot with INT 19.
• Check the HDD.
• Check the floppy disk drive(s).
• Check the main board.
4-2-1-1
D0H
Interrupt handler error.
• Treat as an expansion card problem.
• Check the main board.
4-2-1-3
D2h
Unknown interrupt.
• Treat as an expansion card problem.
• Check the main board.
4-2-2-1
D4h
Pending interrupt error.
• Treat as an expansion card problem.
• Check the main board.
4-2-2-3
D6h
Initialize option ROM error.
• Check the main board.
4-2-3-1
D8h
Shutdown error.
• Check the main board.
4-2-3-3
DAh
Extended Block Move.
• Check the main board.
4-2-4-1
DCh
Shutdown error.
• Check the main board.
Chapter 4
Beep Code
Post Code
Description
What to Check (Recommended)
4-2-4-3
DEh
Keyboard controller failure.
• Check the keyboard.
• Check the keyboard controller.
• Check the main board.
4-3-1-3
E2h
Initialize the chipset.
• Check the main board.
4-3-1-4
E3h
Initialized refresh counter.
• Check the main board.
4-3-2-1
E4h
Check for Forced Flash.
• Check the main board.
4-3-2-2
E5h
Check HW status of ROM.
• Check the main board.
4-3-2-3
E6h
BIOS ROM is OK.
• Check the main board.
4-3-2-4
E7h
Do a complete RAM test.
• Check the system memory.
• Check the main board.
4-3-3-1
E8h
Do OEM initialization.
• Check the main board.
4-3-3-2
E9h
Initialize interrupt
controller.
• Treat as an expansion card problem.
• Check the main board.
4-3-3-3
EAh
Read in bootstrap code.
• Check the HDD.
• Check the floppy disk drive.
• Check the main board.
4-3-3-4
EBh
Initialize all vectors.
• Treat as an expansion card problem.
• Check the main board.
4-3-4-1
ECh
Boot the Flash program.
• Check the main board.
4-3-4-2
EDh
Initialize the boot device.
• Check the HDD.
• Check the floppy disk drive(s).
• Check the main board.
4-3-4-3
EEh
Boot code was read OK.
• Check the HDD.
• Check the floppy disk drive(s).
• Check the main board.
Chapter 4
87
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom/Error
Action in Sequence
LCD backlight doesn't work.
LCD is too dark.
LCD brightness cannot be
adjusted.
LCD contrast cannot be
adjusted.
Enter BIOS Utility to execute Load Setup Default
Settings, then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key do not
work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or
vertical lines displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom/Error
Indicator incorrectly remains off
or on, but system runs correctly.
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom/Error
88
Action in Sequence
Power shuts down during
operation.
Power source (battery pack and power adapter). See
Power System Check.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power on.
Power source (battery pack and power adapter). See
Power System Check.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Power source (battery pack and power adapter). See
Power System Check.
Hold and press the power switch for more than 4 seconds.
System board
Chapter 4
Symptom/Error
Battery can’t be charged.
Chapter 4
Action in Sequence
See Check the Battery Pack.
Battery pack
System board
89
PCMCIA-Related Symptoms
Symptom/Error
Action in Sequence
System cannot detect the PC
Card (PCMCIA).
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears
different from actual size.
Action in Sequence
Enter BIOS Setup Utility to execute Load Default
Settings, then reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom/Error
Action in Sequence
In Windows, multimedia
programs, no sound comes from
the computer.
Audio driver
Speaker
System board
Internal speakers make noise or
emit no sound.
Speaker
System board
Power Management-Related Symptoms
Symptom/Error
90
Action in Sequence
The system will not enter
hibernation.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system does not enter
hibernation mode and four short
beeps every minute.
Press Fn + F4 and see if the computer enters
hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system does not enter
standby mode after closing the
LCD.
LCD cover switch
System board
The system does not resume
from hibernation mode.
Hard disk connection board
Hard disk drive
System board
The system does not resume
from standby mode after
opening the LCD.
LCD cover switch
System board
Battery fuel gauge in Windows
does not go higher than 90%.
Remove battery pack and let it cool for two hours.
Refresh battery (continue to use battery until power off,
then charge battery).
Battery pack
System board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Chapter 4
Peripheral-Related Symptoms
Symptom/Error
Action in Sequence
System configuration does not
match the installed devices.
Enter BIOS Setup Utility to execute Load Default
Settings, then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work
correctly.
Press Fn + F5, LCD/CRT/Both display switching
System board
USB does not work correctly.
System board
Print problems
Ensure the Parallel Port in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device
problems.
Ensure the Serial Port in the Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom/Error
Action in Sequence
Keyboard (one or more keys)
does not work.
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom/Error
Internal modem does not work
correctly.
Action in Sequence
Modem phone port
Modem combo board
System board
Note: If you can not correct the problems according to the anterior tables, see Undetermined Problems.
Chapter 4
91
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware
defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a recurring problem exists.
When analyzing an intermittent problems, follow the procedures below:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
92
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which devices fail, which devices are incorrectly installed, whether a
short circuit happens, or whether the system is inoperative.
Note: Verify if all devices attached are supported by the computer.
Note: Verify if the power supply used at the time of failure is operating correctly. You can refer to Power
System Check.
Follow the procedures below to isolate the failing FRU. Do not isolate non-defective FRU.
1. Power off the computer.
2. Visually check the devices. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery Pack
•
Hard disk drive
•
DIMM
•
CD-ROM / Diskette drive module
•
PC cards
4. Power on the computer.
5. Determine if the problem has been resolved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failed FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU.
•
System board
•
LCD assembly
Chapter 4
93
Chapter 5
Jumper and Connector Location
Top view
#
Name
Description
#
Name
1
CN3
LCD cable connector
2
CN4
Modem board connector
3
CN1
RJ11 connector
4
CN5
Launch board connector
5
CN6
Keyboard connector
6
CN7
Acer FineTrack connector
Chapter 5
Description
94
#
95
Name
Description
#
Name
Description
7
CN8
Smart card connector
8
CN9
Touchpad connector
9
CN722
Microphone connector
10
CN10
5-in-1 card reader connector
Chapter 5
Bottom view
#
Name
1
JACK701
3
Description
#
Name
Description
Ethernet jack
2
CN700
Serial port
CN704
Docking connector
4
CN701
Digital video interface-digital
port
5
CN702
External VGA port
6
JACK700
DC-in jack
7
CN703
Fan cable connector
8
CN6001
Modem jack
9
CN6002
S-video port
10
CN712
CPU socket
11
U715
Graphic controller
12
U717
North bridge
13
CN716
New card socket
14
CN718
Chapter 5
PCMCIA socket
96
#
Name
Description
#
Name
Description
15
D719
IR receiver
16
JACK704
Microphone jack
17
JACK703
Line-in jack
18
JACK702
Headphones/speaker/lineout jack
19
CN717
HDD connector
20
CN714
Battery connector
21
CN715
RTC battery connector
22
CN509
ODD connector
23
CN706
PCI-E socket
24
U708
South bridge
25
CN710
DIMM socket
26
CN711
DIMM socket
Note: CN6002 (S-video port) and CN6001 (Modem jack) locate on IO board which is the apposite direction
from the bottom view.
97
Chapter 5
Chapter 5
Jumper and Connector Location
Top view
#
Name
Description
#
Name
1
CN3
LCD cable connector
2
CN4
Modem board connector
3
CN1
RJ11 connector
4
CN5
Launch board connector
5
CN6
Keyboard connector
6
CN7
Acer FineTrack connector
Chapter 5
Description
94
#
95
Name
Description
#
Name
Description
7
CN8
Smart card connector
8
CN9
Touchpad connector
9
CN722
Microphone connector
10
CN10
5-in-1 card reader connector
Chapter 5
Bottom view
#
Name
1
JACK701
3
Description
#
Name
Description
Ethernet jack
2
CN700
Serial port
CN704
Docking connector
4
CN701
Digital video interface-digital
port
5
CN702
External VGA port
6
JACK700
DC-in jack
7
CN703
Fan cable connector
8
CN6001
Modem jack
9
CN6002
S-video port
10
CN712
CPU socket
11
U715
Graphic controller
12
U717
North bridge
13
CN716
New card socket
14
CN718
Chapter 5
PCMCIA socket
96
#
Name
Description
#
Name
Description
15
D719
IR receiver
16
JACK704
Microphone jack
17
JACK703
Line-in jack
18
JACK702
Headphones/speaker/lineout jack
19
CN717
HDD connector
20
CN714
Battery connector
21
CN715
RTC battery connector
22
CN509
ODD connector
23
CN706
PCI-E socket
24
U708
South bridge
25
CN710
DIMM socket
26
CN711
DIMM socket
Note: CN6002 (S-video port) and CN6001 (Modem jack) locate on IO board which is the apposite direction
from the bottom view.
97
Chapter 5
Chapter 6
FRU (Field Replaceable Unit)
This chapter offers the FRU (Field Replaceable Unit) listing in global configuration of TravelMate 6460/6410.
Please refer to this chapter whenever you order the parts to repair or for RMA (Return Merchandise Authorization).
Please note that when ordering FRU part, you should check the most-up-to-date information available on your
regional web or channel. For whatever reasons, a part number is changed, it will NOT be noted on the printed
service guide. For Acer authorized service providers, your Acer office may have a different part number code from
those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional
Acer office to order FRU parts for service.
Note: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
98
Parts and Exploded Diagram
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
ADAPTER
N/A
ADAPTER 90W DELTA
ADP-90SB BBDEF BLUE
1.7X5.5X11 LF
"ADAPTOR,3PIN,90W,19
VDC,4.74A,240VAC"
AP.09001.009
N/A
ADAPTER 90W LITE-ON
PA-1900-04 RI YELLOW
1.7X5.5X11 LF
"ADAPTOR,3PIN,90W,19
VDC,4.74A,240VAC"
AP.09003.010
N/A
"ADAPTER 90W LSE
SLS0202C19A20LF,
BLACK, 1.7X5.5X11 LF"
"ADAPTOR,3PIN,90W,19
VDC,4.74A,240VAC"
AP.09006.004
N/A
ADAPTER 90W LITE-ON
PA-1900-24 AR BLUE
1.7X5.5X11 LF
"ADAPTOR,3PIN,90W,19
VDC,4.74A,240VAC"
AP.09003.011
N/A
"BATTERY SANYO LI-ION
3S2P 6CELL 2.0AHR
(4,000MAH Y CELL)"
"BATTERY PACK,LIION,11.1V,4000mAH,2P3
S"
BT.00603.024
N/A
"BATTERY SONY LI-ION
3S2P 6CELL 2.0AHR
(4,000MAH G4E CELL)"
"BATTERY PACK,LIION,11.1V,4000mAH,3S2
P"
BT.00604.011
N/A
"BATTERY SANYO LI-ION
4S2P 8CELL 2.4AHR
(4,800MAH CELL)"
"BATTERY PACK,LIION,14.8V,4800mAH,2P4
S"
BT.00803.020
"BATTERY SONY LI-ION
4S2P 86CELL 2.4AHR
(4,800MAH CELL)"
"BATTERY PACK,LIION,14.8V,4800mAH,2P4
S"
BT.00804.017
N/A
BATTERY SANYO LI-ION
3S2P 6CELL 2ND
"BATTERY PACK,LIION,11.1V,3800mAH,2P3
S"
BT.00603.026
N/A
RTC BATTERY 3V
"BATTERY
SET,LI,3V,90mAH,CELL,2
1X20.5,30m"
23.TCXV1.004
CPU INTEL MEROM
CORE 2 DUO T5500
FSB667 2M 1.66G SL9SH
"CPU,1.66GHZ,DUAL
CORE,667MHZ,2M,UFCP
GA,478P,TAP"
KC.55001.DTP
N/A
CPU INTEL MEROM
CORE 2 DUO T5600
FSB667 2M 1.83G SL9SG
"CPU,1.83GHZ,DUAL
CORE,667MHZ,2M,UFCP
GA,478P,TAP"
KC.56001.DTP
N/A
CPU INTEL MEROM
CORE 2 DUO T7200
FSB667 4M 2.0G SL9SF
"CPU,2.0GHZ,DUAL
CORE,667MHZ,4M,UFCP
GA,478P,TAP"
KC.72001.DTP
BATTERY
CPU
99
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
CPU INTEL MEROM
CORE 2 DUO T7200
FSB667 4M 2.16G SL9SE
"CPU,2.16GHZ,DUAL
CORE,667MHZ,4M,UFCP
GA,478P,TAP"
KC.74001.DTP
N/A
CPU INTEL MEROM
CORE 2 DUO T7200
FSB667 4M 2.33G SL9SD
"CPU,2.33GHZ,DUAL
CORE,667MHZ,4MB,UFC
PGA,478P,TAP"
KC.76001.DTP
MINI WIRELESS BOARD
802.11 A/B/G MOW1
INTEL MM872612
"MODULE,WIRELESS
LAN,PCI EXP 802.11A/G"
KI.GLN01.001
N/A
MINI WIRELESS BOARD
802.11 A/B/G MOW2
INTEL MM872659
"MODULE,WIRELESS
LAN,PCI EXP 802.11A/G"
KI.GLN01.002
N/A
MINI WIRELESS BOARD
802.11 A/B/G ROW INTEL
MM874511
"MODULE,WIRELESS
LAN,PCI EXP 802.11B/G"
KI.GLN01.003
N/A
MINI WIRELESS BOARD
802.11 A/B/G JP INTEL
MM874740
"MODULE,WIRELESS
LAN,PCI EXP 802.11A/G"
KI.GLN01.004
N/A
MINI WIRELESS LAN
BOARD 802.11BG INTEL
WM3945AGBG
"MODULE,WIRELESS
LAN,PCI EXP 802.11B/G"
KI.GLN01.005
BLUETOOTH BOARD
FOXCONN T60H928.01
"MODULE,BLUE
TOOTH,USB2.0"
54.AAMVN.004
MODEM BOARD
FOXCONN T60M955.00
"MODEM,MDC,56K,AZALI
A"
54.TCXVN.001
TOUCHPAD SYNAPTICS
TM51PDF1R226
"TOUCH PAD,NO
BUTTON,12P,79.7X47.7,B
LK"
56.TCXVN.001
TOUCHPAD BOTTON
BOARD
"FRU,I/O BOARD
ASSEMBLY,TOUCH PAD
BUTTON BOARD"
55.TCXVN.003
STICK POINT BOARD
WITH FINGER PRINTER
(TravelMate 6460 only)
"FRU,I/O BOARD
ASSEMBLY,STICK
POINT/B WITH FINGER
PRINTER CHIP"
55.TEDVN.001
STICK POINT BOARD W/
O FINGER PRINTER
"FRU,I/O BOARD
ASSEMBLY,STICK POINT
BOARD W/O FINGER
PRINTER CHIP"
55.TCXVN.001
BOARD
N/A
Chapter 6
100
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
I/O BOARD WITH SVIDEO
"FRU,I/O BOARD
ASSEMBLY"
55.TEDVN.002
I/O BOARD W/O S-VIDEO
(TravelMate 6410 only)
"FRU,I/O BOARD
ASSEMBLY,W/O S-VIDEO
CONNECTOR"
55.TCXVN.002
LAUNCH BOARD
"FRU,I/O BOARD
ASSEMBLY,HOTKEY
BOARD"
55.TCXVN.004
OPTICAL BOARD
"FRU,I/O BOARD
ASSEMBLY,ODD MULTI
INTERFACE"
55.TCXVN.005
INVERTER BOARD NEC/
TOKIN 7312S2
"INVERTER,5VDC,AC690
V,65KHz,130X12.5"
19.TCXVN.001
N/A
TOUCHPAD CABLE
"FFC,12P,1L,1.772X0.256
X0.006,PET,S"
50.TCXVN.001
N/A
BUTTON BOARD CABLE
8 PINS TO STICK POINT
BOARD
"FFC,8P,1L,3.27X0.177X0
.006,PET,S"
50.TCXVN.002
N/A
BUTTON BOARD CABLE
8 PINS TO MAINBOARD
"FFC,8P,1L,7.95X0.177X0
.006,PET,S"
50.TCXVN.003
N/A
STICK POINT BOARD
CABLE 12PINS TO MB
"FFC,12P,1L,2.847X0.256
X0.006,PET,S"
50.TCXVN.004
N/A
I/O BOARD CABLE
"FFC,14P,1L,2.638X0.295
X0.006,PET,S"
50.TCXVN.005
BLUETOOTH CABLE
"CABLE,ROUND,8POS,14
0mm,I,BLUETOOTH,32
AW"
50.TCXVN.006
MODEM CABLE WITH
RJ11 CONNECTOR
"CABLE,ROUND,4POS,17
5mm,I,RJ11"
50.TCXVN.007
"LCD CABLE 15"" XGA"
"CABLE,FIBER,40POS,33
9.898mm,I,LCM"
50.TCXVN.011
N/A
"LCD CABLE 15"" SXGA+"
"CABLE,FLAT,40POS,314
mm,I,LCM"
50.TCXVN.012
N/A
"LCD CABLE 15.4""
WXGA"
"CABLE,FIBER,40POS,29
3.23mm,I,LCM"
50.TCXVN.021
N/A
"LCD CABLE 15.4""
WXGA W/CCD"
"CABLE,FIBER,40POS,35
3.091mm,I,LCM"
50.TCXVN.022
N/A
"LCD CABLE 15.4""
WSXGA+"
"CABLE,FLAT,40POS,304
mm,I,LCM"
50.TCXVN.031
N/A
"LCD CABLE 15.4""
WSXGA+ W/CCD"
"CABLE,FIBER,40POS,35
3.091mm,I,LCM"
50.TCXVN.032
POWER CORD 3PIN USA
CORD-ROUND-3POS1828mm-E-POWER-USA
27.AAMVN.001
N/A
CABLE
POWER CORD
N/A
101
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
POWER CORD 3PIN EUR
CORD-ROUND-3POS1850mm-E-POWER-EUR
27.AAMVN.002
N/A
POWER CORD
AUSTRALIA W/LABEL
CORD-ROUND-3POS1850mm-E-POWER-AUL
27.AAMVN.003
N/A
POWER CORD 3PIN UK
CORD-ROUND-3POS1828mm-E-POWER-UK
27.AAMVN.004
N/A
POWER CORD 3PIN
CHINA
"CORD,ROUND,3POS,18
00mm,E,POWER,PRC"
27.AAMVN.005
N/A
POWER CORD 3PIN
SWISS
"CORD,ROUND,3POS,18
30mm,E,POWER,SWITZE
RLAND"
27.AAMVN.006
N/A
POWER CORD SOUTH
AFRICA (AIL)
"CORD,ROUND,3POS,18
30mm,E,POWER,S.AFRI
CAN"
27.AAMVN.007
N/A
POWER CORD 3PIN
SOUTH AFRICA
"CORD,ROUND,3POS,18
00mm,E,SOUTH AFRICA"
27.AAMVN.008
N/A
POWER CORD 3PIN
ITALIAN
"CORD,ROUND,3POS,18
00mm,E,ITL"
27.AAMVN.009
N/A
POWER CORD 3PIN
DENMARK
"CORD,ROUND,3POS,18
00mm,E,DANISH"
27.AAMVN.010
N/A
POWER CORD ISRAEL
"CORD,ROUND,3POS,18
00mm,E,ISRAEL"
27.AAMVN.011
TOUCHPAD BRACKET
"BRACKET,TOP,TOUCH
PAD,SECC"
33.TCXVN.011
DIMM COVER
"SET,COVER,MEMORY"
42.TCXVN.001
HDD COVER
"SET,COVER,HDD"
42.TCXVN.002
N/A
PCMCIA DUMMY CARD
"DUMMY,PCMCIA
CARD,PC+ABS"
42.TCXVN.003
N/A
MINI DUMMY CARD
"DUMMY,EXPRESS
CARD,PC+ABS"
42.TCXVN.004
N/A
LOWER CASE
(TravelMate 6410 only)
"FRU,BOTTOM CASE
ASSEMBLY"
60.TCXVN.001
N/A
UPPER CASE
(TravelMate 6410 only)
"FRU,TOP CASE
ASSEMBLY"
60.TCXVN.002
N/A
MIDDLE COVER
(TravelMate 6410 only)
"SET,COVER,SWITCH"
60.TCXVN.003
CASE/COVER/BRACKET ASSEMBLY
Chapter 6
102
PHOTO
DESCRIPTON
ACER PART NO.
LOWER CASE
(TravelMate 6460 only)
"FRU,BOTTOM CASE
ASSEMBLY"
60.TEDVN.001
UPPER CASE W/O
FINGER PRINTER
(TravelMate 6460 only)
"FRU,TOP CASE
ASSEMBLY"
60.TEDVN.002
UPPER CASE WITH
FINGER PRINTER
(TravelMate 6460 only)
"FRU,TOP CASE
ASSEMBLY"
60.TEDVN.012
MIDDLE COVER
(TravelMate 6460 only)
"SET,COVER,SWITCH"
60.TEDVN.003
N/A
CONNECTOR 2ND HDD
"E.SET,FPC+CONN,50P/
20P,38.06MM"
22.D03VN.001
N/A
BRACKET 2ND HDD
"BRACKET,HDD,BOTTOM
,SECC"
33.D03VN.002
N/A
UPPER CASE 2ND HDD
"CASE,HDD,BOTTOM,PC
+ABS"
60.D03VN.003
N/A
LOWER CASE 2ND HDD
"CASE,HDD,TOP,PC+AB
S"
60.D03VN.004
N/A
COMBO BEZEL GBASE
"SET,BEZEL,ODD"
42.TCXVN.005
N/A
SUPER MULTI BEZEL
GBASE
"SET,BEZEL,ODD"
42.TCXVN.007
OPTICAL RAIL HOLDER
"HOLDER,ODD,PC+ABS"
42.TCXVN.006
HDD HOLDER
"FRAME,HDD,AL"
42.TCXVN.008
CPU HEATSINK FINGER
"FINGER,CPU,SUS301"
33.TCXVN.001
VGA HEATSINK FINGER
"FINGER,VGA,SUS301"
33.TCXVN.002
N/A
103
PARTNAME
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
NORTH BRIDGE
THERMAL BRACKET
LOWER
"BRACKET,THERMAL,BO
TTOM,SECC"
33.TCXVN.008
N/A
NORTH BRIDGE
THERMAL BRACKET
UPPER
"BRACKET,THERMAL,TO
P,SECC"
33.TCXVN.009
N/A
I/O PORT BRACKET
"BRACKET,PCB,DSUB,SUS 301"
33.TXCVN.010
N/A
"LCD COVER 15"""
"FRU,LCD TOP CASE
ASSEMBLY"
60.TCXVN.004
N/A
"LCD BEZEL 15"" W/
LOGO"
"FRU,LCD BOTTOM
CASE ASSEMBLY"
60.TCXVN.005
N/A
"LCD BRACKET 15"" L"
"HINGE-W
BRACKET,DISPLAY,LEFT,
7.9~8.9KGF-"
33.TCXVN.003
N/A
"LCD BRACKET 15"" R"
"HINGE-W
BRACKET,DISPLAY,RIGH
T,7.9~8.9KGF"
33.TCXVN.004
N/A
"LCD BEZEL 15.4"" W/
LOGO"
"FRU,LCD TOP CASE
ASSEMBLY"
60.TCXVN.006
N/A
"LCD COVER 15.4"" W/
LOGO"
"FRU,LCD BOTTOM
CASE ASSEMBLY"
60.TCXVN.007
N/A
"LCD BRACKET 15.4"" L"
"HINGE-W
BRACKET,DISPLAY,LEFT,
8.1~9.1KGF-"
33.TCXVN.005
N/A
"LCD BRACKET 15.4"" R"
"HINGE-W
BRACKET,DISPLAY,RIGH
T,8.1~9.1KGF"
33.TCXVN.006
N/A
CAMERA LATCH
"HINGE-W
BRACKET,CCD,0.6~0.7K
GF-CM"
33.TCXVN.007
N/A
"LCD BEZEL 15.4"" CCD
W/LOGO"
"FRU,LCD TOP CASE
ASSEMBLY"
60.TCXVN.008
N/A
"LCD COVER 15.4"" CCD
W/LOGO"
"FRU,LCD BOTTOM
CASE ASSEMBLY"
60.TCXVN.009
N/A
CCD BEZEL
"SET,BEZEL,CCD"
60.TCXVN.010
N/A
CCD COVER
"CASE,CCD,REAR,PC+A
BS,COAT"
60.TCXVN.011
N/A
CCD BEZEL W/LOGO
0.3M
"SET,BEZEL,CCD"
60.TXCVN.012
N/A
CDRW/DVD COMBO
MODULE 24X
CDRW/DVD COMBO
MODULE 24X
6M.TCXVN.001
N/A
DVD/CDRW COMBO 24X
DRIVE PANASONIC
UJDA-770 G-BASE LF
"DVD,COMBO,8X,24X,24
X,24X,AMBER,M2,128X12
.7X126.1mm,SLIM"
KO.02406.013
N/A
"DVD/CDRW COMBO 24X
DRIVE PHILIPS SCB5265
,GB,LF FW#TX13"
"DVD,COMBO,8X,24X,24
X,24X,M2,128X12.7X126.
1mm,SLIM"
KO.02408.011
COMBO DRIVE
DVD RW DRIVE
Chapter 6
104
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
DVD-RW DRIVE 8X
SUPER MULTI GBASE W/
BEZEL
DVD-RW DRIVE 8X
SUPER MULTI GBASE W/
BEZEL
6M.TCXVN.002
N/A
DVD-RW DRIVE 8X
SUPER MULTI TOSHIBA
TS-L632D W/O BEZEL
"DVD,SUPER
MULTI,5X,8X,6X,8X,8X,8X
,24X,24X,24X,GREEN,12
8X12.7X126.1mm,SLIM"
KU.00801.014
N/A
DVD-RW DRIVE 8X
SUPER MULTI
PANASONIC UJ-850 LF
W/O BEZEL
"DVD,SUPER
MULTI,5X,8X,6X,8X,8X,8X
,24X,16X,24X,AMBER,M2,
128X12.7X126.1mm,SLIM
"
KU.00807.047
N/A
DVD-RW DRIVE 8X
SUPER MULTI PHI SDVD8821 LF W/O BEZEL
"DVD,SUPER
MULTI,5X,8X,6X,8X,8X,8X
,24X,24X,24X,M2,128X12.
7X126.1mm,SLIM"
KU.00809.005
FAN
"FAN.SET,VERTICAL,5V,0
.2A,3650RPM,"
23.TCXVN.003
N/A
HDD 60G SEAGATE 5.4K
SATA 8M ST96812AS (189) MERCURY 2 LF
FW:3.06
"HDD,SATA,60GB,5.4KRP
M,22P,12.5ms,5.5ms,SAT
A II,2.5X0.37,M3"
KH.06001.009
N/A
"HDD 60G HGST 5.4K
SATA 1.5G NCQ
MORAGA+HTS541060G9
SA00,C60D"
"HDD,SATA,60GB,5.4KRP
M,22P,12ms,5.5ms,SATA1
.0,2.5X0.37,M3"
KH.06007.012
N/A
HDD 60G WD 5.4K SATA
8M WD600BEVS-22LAT0
ML60 LF FW:T0
"HDD,SATA,60GB,5.4KRP
M,22P,12ms,5.5ms,SATA1
.0,2.5X0.37,M3"
KH.06008.005
HDD 80G SEAGATE 5.4K
SATA ST98823AS
MERCURY 2 FW:3.06 LF
"HDD,SATA,80GB,5.4KRP
M,22P,12.5ms,5.5ms,SAT
A II,2.5X0.37,M3"
KH.08001.023
N/A
HDD 80G SEAGATE 5.4K
SATA 8M ST98823AS (189) MERCURY 2 LF
FW:3.06
"HDD,SATA,80GB,5.4KRP
M,22P,12.5ms,5.5ms,SAT
A II,2.5X0.37,M3"
KH.08001.027
N/A
HDD 80GB TOSHIBA 5.4K
SATA MK8032GSX
ARIES-B FREE-FALL LF
FW:AS111J
"HDD,SATA,80GB,5.4KRP
M,22P,12ms,5.6ms,SATA1
.0,2.5X0.37,M3"
KH.08004.007
N/A
"HDD 80G HGST 5.4K
SATA 1.5G NCQ
MORAGA+HTS541080G9
SA00,C60D"
"HDD,SATA,80GB,5.4KRP
M,22P,12ms,5.5ms,SATA1
.0,2.5X0.37,M3"
KH.08007.015
N/A
HDD 80G WD 5.4K SATA
8M WD800BEVS-22LAT0
ML60 LF FW:T0
"HDD,SATA,80GB,5.4KRP
M,22P,12ms,5.5ms,SATA1
.0,2.5X0.37,M3"
KH.08008.031
FAN
N/A
HDD/HARD DISK DRIVE
105
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
HDD 100G SEAGATE
5.4K SATA ST9100824AS
MERCURY 2 FW:3.06 LF
"HDD,SATA,100GB,5.4KR
PM,22P,12.5ms,5.6ms,SA
TA1.0,2.5X0.37,M3"
KH.10001.008
N/A
HDD 100G SEAGATE
5.4K SATA 8M
ST9100824AS (-189)
MERCURY 2 FW:3.06 LF
"HDD,SATA,100GB,5.4KR
PM,22P,12.5ms,5.5ms,SA
TA II,2.5X0.37,M3"
KH.10001.009
N/A
HDD 100G TOSHIBA 5.4K
SATA MK1032GSX
ARIES-B FREE-FALL LF
FW:AS021J
"HDD,SATA,100GB,5.4KR
PM,22P,12ms,5.6ms,SATA
1.0,2.5X0.37,M3"
KH.10004.004
N/A
HDD 100G HGST SATA
1.5G
NCQMORAGA+HTS5410
10G9SA00 FW:S60D
"HDD,SATA,100GB,5.4KR
PM,22P,12ms,5.5ms,SATA
1.0,2.5X0.37,M3"
KH.10007.005
N/A
HDD 100G WD 5.4K SATA
8M WD1000BEVS22LAT0 ML60 LF FW:T0
"HDD,SATA,100GB,5.4KR
PM,22P,12ms,5.5ms,SATA
1.0,2.5X0.37,M3"
KH.10008.002
N/A
HDD 120G SEAGATE
5.4K SATA ST9120821AS
LF MERCURY 2 FW:3.06
"HDD,SATA,120GB,5.4KR
PM,22P,12.5ms,5.6ms,SA
TA1.0,2.5X0.37,M3"
KH.12001.025
N/A
HDD 120G SEAGATE
5.4K SATA 8M
ST9120821AS (-189)
MERCURY 2 LF FW:3.06
"HDD,SATA,120GB,5.4KR
PM,22P,12.5ms,5.5ms,SA
TA II,2.5X0.37,M3"
KH.12001.026
N/A
HDD 120G TOSHIBA 5.4K
SATA1.5G W/NCQ
MK1234GSX ARIES-B
FREE-FALL LF
FW:AH001J
"HDD,SATA,120GB,5.4KR
PM,22P,12ms,5.6ms,SATA
1.0,2.5X0.37,M3"
KH.12004.004
N/A
HDD 120G WD 5.4K
SATA WD1200BEVS22LAT0 ML60 LF FW:T0
"HDD,SATA,120GB,5.4KR
PM,22P,12ms,5.5ms,SATA
1.0,2.5X0.37,M3"
KH.12008.016
N/A
HDD 160G SEAGATE
5.4K ST9160821AS
VENUS SATA LF
FW:3.ALA
"HDD,SATA,160GB,5.4KR
PM,22P,12.5ms,5.5ms,SA
TA II,2.5X0.37,M3"
KH.16001.021
N/A
HDD 160G HGST 5.4K
SATA HTS541616J9SA00
SURUGA-B LF F/W: C70P
"HDD,SATA,160GB,5.4KR
PM,22P,12ms,5.5ms,SATA
1.0,2.5X0.37,M3"
KH.16007.011
CPU HEATSINK
"THERMAL
MODULE,CPU"
34.TCXVN.001
VGA HEATSINK
"THERMAL
MODULE,VGA False 1
PRD"
34.TCXVN.002
HEATSINK
KEYBOARD
Chapter 6
106
PHOTO
107
PARTNAME
DESCRIPTON
ACER PART NO.
KEYBOARD DARFON
TM6410/TM6460 US
INTERNATIONAL
"KEYBOARD/W
ST,88,24P,BLACK,USINTL,310X115.52, 5.5mm"
KB.TCX07.001
N/A
KEYBOARD DARFON
TM6410/TM6460
CHINESE
"KEYBOARD/W
ST,88,24P,BLACK,PRC,31
0X115.52,5.5mm"
KB.TCX07.002
N/A
KEYBOARD DARFON
TM6410/TM6460
SPANISH
"KEYBOARD/W
ST,89,24P,BLACK,SPN,31
0X115.52,5.5mm"
KB.TCX07.003
N/A
KEYBOARD DARFON
TM6410/TM6460
THAILAND
"KEYBOARD/W
ST,88,24P,BLACK,THAI,3
10X115.52,5.5mm"
KB.TCX07.004
N/A
KEYBOARD DARFON
TM6410/TM6460
BRAZILIAN
PORTUGUESE
"KEYBOARD/W
ST,89,24P,BLACK,BRZ,31
0X115.52,5.5mm"
KB.TCX07.005
N/A
KEYBOARD DARFON
TM6410/TM6460
KORAEN
"KEYBOARD/W
ST,88,24P,BLACK,KOR,31
0X115.52,5.5mm"
KB.TCX07.006
N/A
KEYBOARD DARFON
TM6410/TM6460 UK
"KEYBOARD/W
ST,89,24P,BLACK,UK,310
X115.52,5.5mm"
KB.TCX07.007
N/A
KEYBOARD DARFON
TM6410/TM6460
GERMAN
"KEYBOARD/W
ST,89,24P,BLACK,GER,31
0X115.52,5.5mm"
KB.TCX07.008
N/A
KEYBOARD DARFON
TM6410/TM6460 ITALIAN
"KEYBOARD/W
ST,89,24P,BLACK,ITA,310
X115.52,5.5mm"
KB.TCX07.009
N/A
KEYBOARD DARFON
TM6410/TM6460
FRENCH
"KEYBOARD/W
ST,89,24P,BLACK,FRE,31
0X115.52,5.5mm"
KB.TCX07.010
N/A
KEYBOARD DARFON
TM6410/TM6460 SWISS/
G
"KEYBOARD/W
ST,89,24P,BLACK,SWI,31
0X115.52,5.5mm"
KB.TCX07.011
N/A
KEYBOARD DARFON
TM6410/TM6460
PORTUGUESE
"KEYBOARD/W
ST,89,24P,BLACK,POU,31
0X115.52,5.5mm"
KB.TCX07.012
N/A
KEYBOARD DARFON
TM6410/TM6460 ARABIC
"KEYBOARD/W
ST,88,24P,BLACK,ARA,31
0X115.52,5.5mm"
KB.TCX07.013
N/A
KEYBOARD DARFON
TM6410/TM6460
BELGIUM
"KEYBOARD/W
ST,89,24P,BLACK,BEL,31
0X115.52,5.5mm"
KB.TCX07.014
N/A
KEYBOARD DARFON
TM6410/TM6460
SWEDISH
"KEYBOARD/W
ST,89,24P,BLACK,SWE,3
10X115.52,5.5mm"
KB.TCX07.015
N/A
KEYBOARD DARFON
TM6410/TM6460 CZECH
"KEYBOARD/W
ST,89,24P,BLACK,CZE,31
0X115.52,5.5mm"
KB.TCX07.016
N/A
KEYBOARD DARFON
TM6410/TM6460
HUNGARIAN
"KEYBOARD/W
ST,89,24P,BLACK,HUN,31
0X115.52,5.5mm"
KB.TCX07.017
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
KEYBOARD DARFON
TM6410/TM6460
NORWEGIAN
"KEYBOARD/W
ST,89,24P,BLACK,NOR,31
0X115.52,5.5mm"
KB.TCX07.018
N/A
KEYBOARD DARFON
TM6410/TM6460 DANISH
"KEYBOARD/W
ST,89,24P,BLACK,DEN,31
0X115.52,5.5mm"
KB.TCX07.019
N/A
KEYBOARD DARFON
TM6410/TM6460
TURKISH
"KEYBOARD/W
ST,89,24P,BLACK,TUR,31
0X115.52,5.5mm"
KB.TCX07.020
N/A
KEYBOARD DARFON
TM6410/TM6460
CANADIAN FRENCH
"KEYBOARD/W
ST,89,24P,BLACK,FR.CA
NADIAN,310X115.52,5.5m
m"
KB.TCX07.021
N/A
KEYBOARD DARFON
TM6410/TM6460
JAPANESE
TBD
KB.TCX07.022
N/A
KEYBOARD DARFON
TM6410/TM6460 GREEK
"KEYBOARD/W
ST,88,24P,BLACK,GRK,31
0X115.52,5.5mm"
KB.TCX07.023
N/A
KEYBOARD DARFON
TM6410/TM6460
RUSSIAN
"KEYBOARD/W
ST,88,24P,BLACK,RUS,31
0X115.52,5.5mm"
KB.TCX07.024
N/A
KEYBOARD DARFON
TM6410/TM6460
SLOVENIAN
"KEYBOARD/W
ST,89,24P,BLACK,SLOVE
NIA,310X115.52,5.5mm"
KB.TCX07.025
N/A
KEYBOARD DARFON
TM6410/TM6460 SLO/
CRO
"KEYBOARD/W
ST,89,24P,BLACK,CROAT
IAN,310X115.52,5.5mm"
KB.TCX07.026
N/A
TBD
"KEYBOARD/W
ST,88,24P,BLACK,HEBRE
W,310X115.52,5.5mm"
TBD
WIRELESS ANTENNA
LEFT/RIGHT
"ANTENNA,DUAL,2.4/
5.2G,770mm,1.37mm"
25.TCXVN.001
N/A
"LCD MODULE 15"" XGA
W/ ANTENNA"
"LCD MODULE 15"" XGA
W/ ANTENNA"
6M.TCXV1.011
N/A
"LCD MODULE 15""
SXGA+ W/ ANTENNA"
"LCD MODULE 15""
SXGA+ W/ ANTENNA"
6M.TCXVN.012
N/A
LCD 15 IN . SXGA+ AU
B150PG03 200 NITS
SPWG-B
"LCM,15,TFT,SXGA+,LVD
S,575g"
LK.15005.008
N/A
LCD 15 IN. XGA AUO
B150XG02. V4 LEADFREE
"LCM,15,TFT,XGA,LVDS,5
85g"
LK.15005.010
N/A
LCD MODULE 15.4IN.
WXGA NON-GLARE W/
ANTENNA
LCD MODULE 15.4IN.
WXGA NON-GLARE W/
ANTENNA
6M.TCXVN.021
COMMUNICATION MODULE
LCD
Chapter 6
108
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
LCD MODULE 15.4IN.
WXGA NON-GLARE W/
ANTENNA &CCD 1.3M
LCD MODULE 15.4IN.
WXGA NON-GLARE W/
ANTENNA &CCD 1.3M
6M.TCXVN.022
N/A
LCD MODULE 15.4IN.
WXGA NON-GLARE W/
ANTENNA &CCD 0.3M
LCD MODULE 15.4IN.
WXGA NON-GLARE W/
ANTENNA &CCD 0.3M
6M.TCXVN.023
N/A
"LCD 15.4 WXGA AUO
B154EW02-V0 NONGLARE 200NITS, 16MS
(LF)"
"LCM,15.4,TFT,WXGA,LV
DS,500g"
LK.15405.013
N/A
"15.4"" WXGA LPL
LP154W01-TLE1NO NGLARE 16MS, 200NITS"
"LCM,15.4,TFT,WXGA,LV
DS,560g"
LK.15408.019
N/A
LCD MODULE 15.4IN.
WSXGA+ NON-GLARE
W/ANTENNA
LCD MODULE 15.4IN.
WSXGA+ NON-GLARE
W/ANTENNA
6M.TCXVN.031
N/A
LCD MODULE 15.4IN.
WSXGA+ NON-GLARE
W/ANTENNA &CCD 1.3M
LCD MODULE 15.4IN.
WSXGA+ NON-GLARE
W/ANTENNA &CCD 1.3M
6M.TCXVN.032
N/A
LCD 15.4 IN. WSXGA+
QDI QD15AL02-01 NON
GLARE LF
"LCM,15.4,TFT,WSXGA+,
LVDS,585g"
LK.15409.014
N/A
LCD MODULE 15.4IN.
WXGA+ NON-GLARE W/
ANTENNA
LCD MODULE 15.4IN.
WXGA+ NON-GLARE W/
ANTENNA
6M.TCXVN.041
N/A
LCD MODULE 15.4IN.
WXGA+ NON-GLARE W/
ANTENNA & CCD 1.3M
LCD MODULE 15.4IN.
WXGA+ NON-GLARE W/
ANTENNA & CCD 1.3M
6M.TCXVN.042
N/A
"LCD 15.4"" WXGA+ CMO
N154C2-L03 NON-GLARE
10MS 200NITS"
"LCM,15.4,TFT,WXGA+,L
VDS,530g"
LK.1540D.013
CCD CAMERA 1.3M
LOGITECH SHAGGY2
"DIGITAL CAMERA,1.3M"
56.AAMVN.003
MAINBOARD TM6410
INTEL 945GM LF UMA
(TravelMate 6410)
"FRU,MAIN BOARD
ASSEMBLY"
MB.TCX0B.001
"MAINBOARD TM6460
INTEL 945PM M52P128M
LF W/CARD READER,
SMART CARD, DVI, & TVOUT"
(TravelMate 6460)
"FRU,MAIN BOARD
ASSEMBLY"
MB.TED0B.001
N/A
SO-DIMM DDRII533
256MB NANYA
NT256T64UH4A1FN-37B
LF
"MEMORY
MODULE,256MB,PC24200,SODIMM,200P,32M
X64,"
KN.25603.029
N/A
SO-DIMM DDRII533
256MB SAMSUNG
M470T3354CZ3-CD5 LF
"MEMORY
MODULE,256MB,PC24200,200P,32MX64,"
KN.2560B.017
CAMERA
N/A
MAINBOARD
N/A
MEMORY
109
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
SO-DIMM DDRII533 256M
HYNIX HYMP532S64BP6C4
"MEMORY
MODULE,256MB,PC24200,SODIMM,200P,32M
X64,"
KN.2560G.012
N/A
SO-DIMM DDRII533
512MB NANYA
NT512T64UH8A1FN-37B
LF
"MEMORY
MODULE,512MB,PC24200,SODIMM,200P,64M
X64,"
KN.51203.023
N/A
SO-DIMM DDRII533
512MB SAMSUNG
M470T6554CZ3-CD500
LF
"MEMORY
MODULE,512MB,PC24200,200P,64MX64,"
KN.5120B.015
N/A
SO-DIMM DDRII533512M
HYNIX HYMP564S64BP6C4
"MEMORY
MODULE,512MB,PC24200,SODIMM,200P,64M
X64,"
KN.5120G.013
N/A
SO-DIMM DDRII533 1GB
INFINEON
HYS64T128021HDL-3.7-B
"MEMORY
MODULE,1GB,PC24200,SODIMM,200P,128M
X64,"
KN.1GB02.030
N/A
SO-DIMM DDRII533 1GB
MANYA
NT1GT64UH8A0BN-37B
LF
"MEMORY
MODULE,1024MB,PC24200,DDR2,200P,128MX6
4,"
KN.1GB03.006
N/A
SO-DIMM DDRII533 1GB
SAMSUNG
M470T2953CZ3-CD5 LF
"MEMORY
MODULE,1GB,PC24200,DDR2,200P,128MX6
4,"
KN.1GB0B.004
N/A
SO-DIMM DDRII667
256MB NANYA
NT256T64UH4A1FN-3C
LF
"MEMORY
MODULE,256MB,PC25300,DDR2,200P,32MX64
,"
KN.25603.027
N/A
SO-DIMM DDRII667
256MB SAMSUNG
M470T3354CZ3-CE6 LF
"MEMORY
MODULE,256MB,PC25300,DDR2,200P,32MX64
,"
KN.2560B.018
N/A
SO-DIMM DDRII667
256MB HYNIX
HYMP532S64BP6-Y5 LF
(.09UM)
"MEMORY
MODULE,256MB,PC25300,DDR2,200P,32MX64
,"
KN.2560G.013
N/A
SO-DIMM DDRII667
512MB INFINEON
HYS64T64020HDL-3S-B
(.09U/G)
"MEMORY
MODULE,512MB,PC25300,DDR2,200P,64MX64
,"
KN.51202.035
N/A
SO-DIMM DDRII667
512MB NANYA
NT512T64UH8A1FN-3C
LF
"MEMORY
MODULE,512MB,PC25300,DDR2,200P,64MX64
,"
KN.51203.025
N/A
SO-DIMM DDRII667
512MB SAMSUNG
M470T6554CZ3-CE6 LF
"MEMORY
MODULE,512MB,PC25300,DDR2,200P,64MX64
,"
KN.5120B.018
Chapter 6
110
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
SO-DIMM DDRII667
512MB HYNIX
HYMP564S64BP6-Y5 LF
(.09UM)
"MEMORY
MODULE,512MB,PC25300,DDR2,200P,64MX64
,"
KN.5120G.014
N/A
SO-DIMM DDRII667 1GB
NANYA
NT1GT64U8HA0BN-3C
LF
"MEMORY
MODULE,1GB,PC25300,DDR2,200P,128MX6
4,"
KN.1GB03.009
N/A
SO-DIMM DDRII667 1GB
SAMSUNG
M470T2953CZ3-CE6
"MEMORY
MODULE,1GB,PC25300,DDR2,200P,128MX6
4,"
KN.1GB0B.005
N/A
LCD CUSHION LEFT
"BUMPER,DISPLAY,LEFT,
SILICONE"
47.TCXV1.001
N/A
LCD CUSHION RIGHT
"BUMPER,DISPLAY,RIGH
T,SILICONE"
47.TCXV1.002
N/A
BUMPER DOCK
"BUMPER,BOTTOM,DOC
K,SILICONE"
47.TCXV1.003
N/A
BUMPER CARDREADER
"BUMPER,TOP,CARDRE
ADER,SILICONE"
47.TCXV1.004
N/A
KNOB WLAN & BT
"KNOB,TOP,WIFI,PC+AB
S,COAT"
47.TCXVN.005
MICROPHONE
"BUZZER,9X5.5 False 1
PRD"
23.TCXVN.001
SPEAKER SET
"SPEAKER.SET,4OHM,1.
5W,9.5mm,25X12X4.6mm,
55/110mm"
23.TCXVN.002
SPEAKER SET
"SPEAKER.SET,8OHM,2
W,24mm,62X13X1394X12X14mm,55/110mm"
6039B0009801
N/A
SCREW
"SCREW,I,M2.5,5mm,M,0.
45mm,0.8mm,BNI,PATC"
86.D03VN.004
N/A
SCREW
SCREWWI30030M(5.0Dx1.5T)-NIHARDEN
86.AAMVN.001
N/A
SCREW
SCREWI25060M(4.5Dx0.8T)-BKPATCH
86.AAMVN.002
N/A
SCREW
SCREW-I20040M-BKPATCH
86.TCXVN.001
N/A
SCREW
SCREWI25025M(4.5Dx0.8T)-BKPATCH
86.TCXVN.002
MISCELLANEOUS
MICROPHONE
N/A
SPEAKER
N/A
SCREW
111
Chapter 6
PHOTO
PARTNAME
DESCRIPTON
ACER PART NO.
N/A
SCREW
SCREWI250100M(4.5DX0.8T)-BKPATCH
86.TCXVN.003
N/A
SCREW
SCREWI20050M(4.5Dx0.5T)-BKPATCH
86.TCXVN.004
N/A
SCREW
SCREWI25040M(4.5Dx0.8T)-BKPATCH
86.TCXVN.005
N/A
SCREW
SCREW-I-M2.0-3.0-M4.0Dx0.3T-BK-PATCH
86.TCXVN.006
N/A
SCREW
"SCREW,I,M2.5,3.0mm,M,
4.5mm,0.8mm,BNI,PAT"
86.TCXVN.007
Chapter 6
112
Download PDF

advertising