User`s guide | Acer 7200 Personal Computer User Manual

VT7200-ug-e.book Page i Wednesday, July 18, 2001 1:28 PM
Veriton 7200
User’s guide
VT7200-ug-e.book Page ii Wednesday, July 18, 2001 1:28 PM
Copyright © 2001 Acer Incorporated
All Rights Reserved.
Veriton 7200
User’s guide
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revision or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date, and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your computer. All correspondence concerning your unit should include the serial
number, model number, and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopy, recording, or otherwise,
without the prior written permission of Acer Incorporated.
Model Number : _________________________________
Serial Number: ___________________________________
Purchase Date: ___________________________________
Place of Purchase: ________________________________
Acer and the Acer Logo are registered trademarks of Acer Inc. Other company’s product
names or trademarks are used herein for identification purposes only and belong to their
respective companies.
VT7200-ug-e.book Page iii Wednesday, July 18, 2001 1:28 PM
iii
Notices
FCC notice
This device has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses,
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the
device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the device and receiver
•
Connect the device into an outlet on a circuit different from that
to which the receiver is connected
•
Consult the dealer or an experienced radio/television technician
for help
Notice: Shielded cables
All connections to other computing devices must be made using
shielded cables to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.)
certified to comply with the Class B limits may be attached to this
equipment. Operation with noncertified peripherals is likely to result
in interference to radio and TV reception.
Caution! Changes or modifications not expressly approved by
the manufacturer could void the user’s authority, which is granted
by the Federal Communications Commission, to operate this
computer.
VT7200-ug-e.book Page iv Wednesday, July 18, 2001 1:28 PM
iv
Use conditions
This part complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Remarque à l’intention des utilisateurs canadiens
Cet appareil numérique de la classe B respected toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
Important safety instructions
Read these instructions carefully. Save these instructions for future
reference.
1.
Follow all warnings and instructions marked on the product.
2.
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
3.
Do not use this product near water.
4.
Do not place this product on an unstable cart, stand, or table. The
product may fall, causing serious damage to the product.
5.
Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the
product and to protect it from overheating, these openings must
not be blocked or covered. The openings should never be blocked
by placing the product on a bed, sofa, rug, or other similar surface.
This product should never be placed near or over a radiator or
heat register, or in a built-in installation unless proper ventilation
is provided.
6.
This product should be operated from the type of power indicated
on the marking label. If you are not sure of the type of power
available, consult your dealer or local power company.
7.
Do not allow anything to rest on the power cord. Do not locate
this product where persons will walk on the cord.
VT7200-ug-e.book Page v Wednesday, July 18, 2001 1:28 PM
v
8.
If an extension cord is used with this product, make sure that the
total ampere rating of the equipment plugged into the extension
cord does not exceed the extension cord ampere rating. Also,
make sure that the total rating of all products plugged into the
wall outlet does not exceed the fuse rating.
9.
Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out
parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.
10. Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage points or
other risks. Refer all servicing to qualified service personnel.
11. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a.
When the power cord or plug is damaged or frayed
b.
If liquid has been spilled into the product
c.
If the product has been exposed to rain or water
d.
If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to normal condition.
e.
If the product has been dropped or the cabinet has been
damaged
f.
If the product exhibits a distinct change in performance,
indicating a need for service.
12. Replace the battery with the same type as the product's battery we
recommend. Use of another battery may present a risk of fire or
explosion. Refer battery replacement to a qualified serviceman.
13. Warning! Batteries may explode if not handled properly. Do not
disassemble or dispose of them in fire. Keep them away from
children and dispose of used batteries promptly.
14. Use only the proper type of power supply cord set (provided in
your accessories box) for this unit. It should be a detachable type:
UL listed/CSA certified, type SVT, rated 7A 125V minimum, VDE
approved or its equivalent. Maximum length is 15 feet (4.6
meters).
VT7200-ug-e.book Page vi Wednesday, July 18, 2001 1:28 PM
vi
Laser compliance statement
The CD or DVD drive in this computer is a laser product. The CD or
DVD drive’s classification label (shown below) is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID
EXPOSURE TO BEAM.
APPAREIL A LASER DE CLASSE 1 PRODUIT
LASERATTENTION: RADIATION DU FAISCEAU LASER INVISIBLE EN CAS
D’OUVERTURE. EVITTER TOUTE EXPOSITION AUX RAYONS.
LASER KLASSE 1
VORSICHT: UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG
GEÖFFNET, NICHT DEM STRAHLL AUSSETZEN
PRODUCTO LÁSER DE LA CLASE I
ADVERTENCIA: RADIACIÓN LÁSER INVISIBLE AL SER ABIERTO. EVITE
EXPONERSE A LOS RAYOS.
ADVARSEL: LASERSTRÅLING VEDÅBNING SE IKKE IND I STRÅLEN
VARO! LAVATTAESSA OLET ALTTINA LASERSÅTEILYLLE.
VARNING: LASERSTRÅLNING NÅR DENNA DEL ÅR ÖPPNAD ÅLÅ
TUIJOTA SÅTEESEENSTIRRA EJ IN I STRÅLEN
VARNING: LASERSTRÅLNING NAR DENNA DEL ÅR ÖPPNADSTIRRA EJ
IN I STRÅLEN
ADVARSEL: LASERSTRÅLING NAR DEKSEL ÅPNESSTIRR IKKE INN I
STRÅLEN
Lithium battery statement
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning
må kun ske med batteri af samme fabrikat og type. Léver det brugte
batteri tilbage til leverandøren.
VT7200-ug-e.book Page vii Wednesday, July 18, 2001 1:28 PM
vii
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme
batteritype eller en tilsvarende type anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til fabrikantens instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte. Anvãnd samma batterityp
eller en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera anvãnt batteri enligt fabrikantens instruktion.
VAROITUS
Päristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty
paristo valmistajan ohjeiden mukaisesti.
VORSICHT!
Explosionsgefahr bei unsachgemäßen Austausch der Batterie Ersatz
nur durch denselben oder einem vom Hersteller empfohlenem
ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des
Herstellers.
Year 2000 compliance statement
The Veriton 7200 computer carries the "Hardware NSTL Tested Year
2000 Compliant" logo, which certifies that this model has been tested
by NSTL using the YMark2000 test, and has been found to meet NSTL's
standards for Year 2000 hardware compliance.
For more details, check the Acer Year 2000 Resource Center at http://
global.acer.com/service/pcy2000.html
VT7200-ug-e.book Page viii Wednesday, July 18, 2001 1:28 PM
viii
Notices
iii
1 First things first
1
Package contents
Taking care of your computer
Important tips
Cleaning and servicing
Asking for technical assistance
Accessing the online guide
3
4
4
4
5
6
2 System tour
7
Features
Performance
Multimedia
Connectivity
Front panel
Rear panel
Keyboard
Mouse
Disk drives
Floppy drive
CD-ROM/DVD-ROM/CD-RW drive
Hard disk
9
9
9
9
10
12
14
17
18
18
19
20
3 Setting up your computer
21
Arranging a comfortable work area
Adjusting your chair
Positioning your Veriton PC
Positioning your monitor
Positioning your keyboard
Positioning your mouse
Connecting peripherals
USB Keyboard
USB Mouse
Monitor
Power cable
Turning on your computer
Turning off your computer
Connecting options
Printer
Serial mouse
23
23
23
24
24
24
25
25
26
27
28
29
31
32
32
33
Contents
VT7200-ug-e.book Page ix Wednesday, July 18, 2001 1:28 PM
VT7200-ug-e.book Page x Wednesday, July 18, 2001 1:28 PM
x
Network
USB devices
Multimedia devices
34
35
37
4 Upgrading your computer
41
Installation precautions
ESD precautions
Preinstallation instructions
Post-installation instructions
Opening your computer
To remove the side panel
To reinstall the side panel
Internal components
Replacing the hard disk
Installing an expansion card
System boards
Mainboard layout
Audio board
Installing additional memory
To install a DIMM
To reconfigure your computer
43
43
43
44
45
45
46
48
49
51
53
53
56
57
58
58
5 Software
Acrobat Reader
LDCM
Norton AntiVirus
NTI CD-Maker 2000 (for models with CD-RW)
PowerDVD (for models with DVD)
VariSpeed (Windows Me only)
BIOS utility
Reinstalling programs
59
62
63
64
65
66
67
68
69
6 Q&A
71
Index
77
VT7200-ug-e.book Page 1 Wednesday, July 18, 2001 1:28 PM
1 First things first
VT7200-ug-e.book Page 2 Wednesday, July 18, 2001 1:28 PM
This chapter describes the contents of your
computer package and also provides
important tips on how to take care of your
computer.
VT7200-ug-e.book Page 3 Wednesday, July 18, 2001 1:28 PM
3
Package contents
Before you unpack your computer, make sure that you have enough
space to set up your computer.
Carefully unpack the carton and remove the contents. If any of the
following items are missing or damaged, contact your dealer
immediately:
•
Veriton 7200
•
Items contained in the accessory box
•
USB keyboard
•
USB mouse
•
User’s guide and installation poster
•
Other user documentation and third-party software
VT7200-ug-e.book Page 4 Wednesday, July 18, 2001 1:28 PM
4
1 First things first
Taking care of your computer
Please read the important instructions listed in this section. Following
these instructions will help you maximize the durability of your
computer.
Important tips
•
Do not expose the computer to direct sunlight. Do not place it
near sources of heat, such as a radiator.
•
Do not subject the computer to magnetic fields.
•
Do not expose the computer to rain or moisture.
•
Do not spill water on the computer.
•
Do not subject the computer to heavy shock or vibration.
•
Do not expose the computer to dust and dirt.
•
Never place the system on uneven surfaces.
•
Do not step on the power cord or place heavy objects on top of it.
Carefully route the power cord and any cables away from personal
traffic.
•
When unplugging the power cord, do not pull on the cord itself
but pull on the plug.
•
The total ampere rating of the equipment plugged in should not
exceed the ampere rating of the cord if you are using an extension
cord. Also, the total current rating of all equipment plugged into
a single wall outlet should not exceed the fuse rating.
•
Check the documentation that came with your software programs
to see if you can select other combinations of resolution and color.
These adjustments could make viewing the screen more
comfortable.
Cleaning and servicing
To clean your computer and keyboard
1.
Turn off the computer and unplug the power cord.
2.
Use a soft cloth moistened with water and gently wipe the exterior
of the computer and the keyboard. Do not use liquid or aerosol
cleaners.
VT7200-ug-e.book Page 5 Wednesday, July 18, 2001 1:28 PM
5
To clean your mouse
1.
Open the circular cover underneath the mouse.
2.
Take out the rubber ball and wipe it with a soft, damp cloth.
3.
Put the ball back and close the cover.
To clean your monitor
Make sure that you keep your screen clean. For cleaning instructions,
refer to the documentation that came with your monitor.
When to contact a service technician
•
If you dropped and damaged the computer.
•
If liquid has been spilled into the computer.
•
If the computer is not operating normally.
Asking for technical assistance
For technical assistance, contact your local dealer or distributor. You
may also access the Acer Web site (www.acer.com) for information on
how and where to contact the service centers available in your area.
VT7200-ug-e.book Page 6 Wednesday, July 18, 2001 1:28 PM
6
1 First things first
Accessing the online guide
You may also refer to the Veriton 7200 online guide for information
about your computer. To access the online guide, simply double-click
on the Veriton 7200 Online icon on your Windows desktop.
VT7200-ug-e.book Page 7 Wednesday, July 18, 2001 1:28 PM
2 System tour
VT7200-ug-e.book Page 8 Wednesday, July 18, 2001 1:28 PM
This chapter discusses the features and
components of your computer.
VT7200-ug-e.book Page 9 Wednesday, July 18, 2001 1:28 PM
9
Features
Here are just a few of your computer’s many features:
Performance
•
Intel Pentium® 4 processor with Intel NetBurst™ microarchitecture
•
System memory expandable to a maximum of 3 GB
•
Power management function
•
3.5-inch floppy drive
•
DVD-ROM, CD-ROM or CD-RW drive
•
High-capacity, Enhanced-IDE hard disk
Multimedia
•
128-bit graphics accelerator installed in the AGP Pro card slot
•
3-D quality audio system via onboard audio controller
•
Audio-in/Line-in, Audio-out/Line-out, Headphone-out, Mic-in, and
Game/MIDI interfaces
Note: The system has two microphone-in ports (front and rear).
However, you can not use both of them at the same time. The
default setting for your system enables the microphone-in port in
front and disables the one at the back.
Connectivity
•
PS/2 mouse and keyboard interfaces
•
Two serial and one parallel interfaces
•
Universal Serial Bus (USB) ports (two on the front and two on the
rear panel)
•
High-speed fax/data PCI modem (optional)
•
10Base-T/100Base-TX network support with remote wake-up
function
VT7200-ug-e.book Page 10 Wednesday, July 18, 2001 1:28 PM
10
2 System tour
Front panel
Your computer’s front panel consists of the following:
Label
Icon
Component
1
CD-ROM/DVD-ROM/CD-RW tray
2
Stop/Eject button
3
Skip/Forward button
4
Hard disk activity light-emitting diode (LED)
5
LAN activity LED
6
Power LED
7
Power switch
8
CD-ROM/DVD-ROM/CD-RW LED
9
Volume control tuner
VT7200-ug-e.book Page 11 Wednesday, July 18, 2001 1:28 PM
11
Label
Icon
Component
10
CD-ROM/DVD-ROM/CD-RW Headphone/
Earphone port
11
5.25-inch drive bays
12
3.5-inch floppy drive
13
Floppy drive LED
14
Floppy drive eject button
15
Speaker-out/Line-out port
16
Microphone-in port (front)see note
17
USB ports
Note: The system has two microphone-in ports (front and rear).
However, you can not use both of them at the same time. The default
setting for your system enables the microphone-in port in front and disables
the one at the back.
VT7200-ug-e.book Page 12 Wednesday, July 18, 2001 1:28 PM
12
2 System tour
Rear panel
Your computer’s rear panel consists of the following:
Label
Icon
Color
Component
1
Power switch
2
Voltage selector switch
3
Power cord socket
4
White
Network port
5
Burgundy
Parallel/Printer port
6
Gold
Game/MIDI port
7
CRT/LCD monitor port
8
Power supply
9
Green
PS/2 mouse port
VT7200-ug-e.book Page 13 Wednesday, July 18, 2001 1:28 PM
13
Label
Icon
Color
Component
10
Purple
PS/2 keyboard port
11
Black
USB ports
12
Teal or
Turquoise
Serial port
13
Lime
Audio-out/Line-out jack
14
Light
blue
Audio-in/Line-in jack
15
Microphone-in port (rear)
16
Expansion slots
For information on how to connect the peripherals, see “Connecting
peripherals” on page 25 and “Connecting options” on page 32.
VT7200-ug-e.book Page 14 Wednesday, July 18, 2001 1:28 PM
14
2 System tour
Keyboard
The keyboard has full-sized keys that include separate cursor keys, two
Windows keys, and twelve function keys.
Item
Component
Description
1
Function keys
Performs specific functions, depending
on the application that uses them.
2
Caps lock
When activated, all alphabetic
characters typed appear in uppercase
(same function as pressing Shift +
<letter>).
VT7200-ug-e.book Page 15 Wednesday, July 18, 2001 1:28 PM
15
Item
Component
Description
3
Windows logo key
Start button. Combinations with this
key perform special functions, such as:
•
Windows + Tab: Activate the next
Taskbar button
•
Windows + E: Explore My
Computer
•
Windows + F: Find Document
•
Windows + M: Minimize All
•
Shift + Windows + M: Undo
Minimize All
•
Windows + R: Display Run dialog
box
4
Application key
Opens the applications context menu
(same function as clicking the right
button of the mouse).
5
Cursor keys
Also called arrow keys, let you move the
cursor around the screen. They serve the
same function as the arrow keys on the
numeric pad when the Num lock is
toggled off.
6
Palm rest (detachable)
Provides a comfortable place to rest your
hands while typing.
7
Num lock
When activated, the keypad is set to
numeric mode, i.e., the keys function as
a calculator (complete with arithmetic
operators such as +, -, * and /).
8
Scroll lock
When activated, the screen moves one
line up or down when you press the up
arrow or down arrow respectively. Take
note that Scroll Lock may not work with
some applications.
9
Volume control/Mute
Controls the speaker volume. Turn it
clockwise or counterclockwise to adjust
the volume. Press it to toggle between
mute and sound.
VT7200-ug-e.book Page 16 Wednesday, July 18, 2001 1:28 PM
16
2 System tour
Item
Component
Description
10
Multimedia keys
Allow you to do the following:
11
12
Internet/Suspend keys
Programmable keys
•
Play/Pause button
: press to
start playing the audio track or
video file. Press again to pause.
•
Stop button
: press to stop
playing the audio track or video
file.
•
Forward button
: press to skip
forward to the next track or video
file and start playing.
•
Backward button
: press to skip
backward to the previous track or
video file and start playing.
Consist of three buttons:
•
Email button
: launches the
email application that came
bundled with your system.
•
Web browser button
:
launches the browser application
that came bundled with your
system.
•
Suspend/Resume button
:
puts the system to sleep when
pressed. To wake up the system,
press it again.
Help you directly access a URL (Web site)
or launch any program, file, or
application in your system. The fifth key
is set to launch the media player.
To configure the settings of each key,
right-click on the Magic Keyboard icon
located on the Windows taskbar.
VT7200-ug-e.book Page 17 Wednesday, July 18, 2001 1:28 PM
17
Mouse
Your mouse has one ratchet wheel and two buttons: a left button and
a right button. Quickly pressing and releasing the buttons is called
clicking. Sometimes, you will need to do a double-click (clicking the
same button twice quickly) or a right-click (clicking the right button
quickly).
The ratchet wheel in between the two buttons is added to provide
easier scrolling capability. By simply moving the wheel with your index
finger, you can quickly move through multiple pages, lines, or
windows. The wheel may also function as a third button allowing you
to quickly click or double-click an icon or a selected item.
For information on how to clean your mouse, see “To clean your
mouse” on page 5.
Note: If you are left-handed, refer to your Windows manual for
instructions on how to set up your mouse for left-handed use.
VT7200-ug-e.book Page 18 Wednesday, July 18, 2001 1:28 PM
18
2 System tour
Disk drives
Your computer comes with the following disk drives:
Floppy drive
Your computer’s 3.5-inch floppy drive can handle 720-KB and 1.44-MB
capacity diskettes.
The floppy diskettes are compact, lightweight, and easy to carry
around. Here are some tips on how to take care of your diskettes:
•
Always make backup copies of the diskettes that contain
important data or program files.
•
Keep diskettes away from magnetic fields and sources of heat.
•
Avoid removing a diskette from a drive when the floppy drive
activity light is on.
•
Write-protect your diskettes to prevent accidental erasure. To do
this, slide the write-protect tab to the write-protect position.
Write-protected
•
Not
write-protected
When you put a label on a 3.5-inch diskette, make sure that the
label is properly attached (flat on the surface) and within the
labeling area (area with a slight surface depression) on the
diskette. An improperly attached label may cause a diskette to get
stuck in a drive when you are inserting or removing it.
VT7200-ug-e.book Page 19 Wednesday, July 18, 2001 1:28 PM
19
CD-ROM/DVD-ROM/CD-RW drive
Your computer may come with a CD-ROM, DVD-ROM or a CD-RW
drive. This drive is located on the front panel of your computer. The
CD-ROM drive allows you to play different types of compact discs (CDs).
The DVD-ROM drive allows you to play not only old CD-ROMs, CD-I
discs, and video CDs, but new digital video discs (DVDs) as well. The
CD-RW drive allows you to record or burn CD-RW (recordable and
rewritable) discs. DVD or DVD-ROM is a new type of disc media that
holds a minimum of 4.7-GB (gigabytes), enough for a full-length
movie. It is believed that it will eventually replace CD-ROMs, as well as
VHS video cassettes and laser discs.
CDs and DVDs, like diskettes, are also compact, lightweight, and easy
to carry around. However, they are more delicate than diskettes and
must be handled with extra care.
To insert a CD or DVD into your computer’s CD-ROM or DVD drive:
1.
Gently push the eject button located on the front panel.
VT7200-ug-e.book Page 20 Wednesday, July 18, 2001 1:28 PM
20
2 System tour
2.
When the disc tray slides open, insert the CD or DVD. Make sure
that the label or title side of the disc is facing upward. When
holding a disc, hold it by the edges to avoid leaving smudges or
fingerprints.
3.
Push the eject button again to close the tray.
To take care of your CDs and DVDs
•
Keep your disc in its case when not in use to avoid scratches or
other damage. Any kind of dirt or damage can affect the data on
the disc, impair the disc lens reader on the CD or DVD drive, or
stop the computer from successfully reading the disc.
•
When handling discs, always hold them by the edges to avoid
smudges or fingerprints.
•
When cleaning discs, use a clean, dust-free cloth and wipe in a
straight line from the center to the edge. Do not wipe in a circular
motion.
•
Clean your CD or DVD drive periodically. You may refer to the
Cleaning kit for instructions. Cleaning kits can be purchased in any
computer or electronics shop.
Hard disk
Your computer is preinstalled with a high-capacity Enhanced-IDE (EIDE) hard disk. If you want to replace your hard disk or upgrade it,
contact your dealer or a qualified service technician for support.
VT7200-ug-e.book Page 21 Wednesday, July 18, 2001 1:28 PM
3 Setting up your
computer
VT7200-ug-e.book Page 22 Wednesday, July 18, 2001 1:28 PM
This chapter contains step-by-step
instructions on how to set up your computer
and connect additional peripherals.
VT7200-ug-e.book Page 23 Wednesday, July 18, 2001 1:28 PM
23
Arranging a comfortable work area
Working safely begins with the arrangement of your work space and
the proper use of equipment. For this reason, it is very important to
take time and think about how you are going to arrange your work
area.
Here are some points to consider:
Adjusting your chair
Having the right kind of chair does not necessarily mean that you’ll be
properly supported. It is necessary to adjust your chair to fit your body.
Proper body posture will make you more comfortable and productive.
•
Avoid tilting your chair. If you have a chair that tilts, lock the tilt
knobs so that your chair will not tilt forward or backward while
you are using your computer.
•
Adjust your chair height in such a way that you can sit on it with
your thighs parallel to the floor and your feet resting flat on the
floor.
•
Rest your body on the chair back. Your torso works harder to
maintain balance if you do not rest your body on the chair back.
Positioning your Veriton PC
Take note of the following when selecting a location for your
computer:
•
Do not put your computer near any equipment that might cause
electromagnetic or radio frequency interference such as radio
transmitters, televisions, copy machines, or heating and airconditioning equipment.
•
Avoid dusty areas and extremes of temperature and humidity.
•
You may place your computer beside your desk or under your
table, as long as it does not block the space that you need for
working and moving.
VT7200-ug-e.book Page 24 Wednesday, July 18, 2001 1:28 PM
24
3 Setting up your computer
Positioning your monitor
Place your monitor at a comfortable viewing distance, usually 50 to 60
centimeters away. Adjust the display in such a way that the top of the
screen is at or slightly below eye level.
Positioning your keyboard
The location of the keyboard is a very important factor to your
posture. Placing it too far away will make your body lean forward
forcing you to sit in an unnatural position. Placing it too high will add
tension to your shoulder muscles.
•
The keyboard should be placed just above your lap. Adjust the
keyboard height by flipping the folding stands located under the
keyboard.
•
Keep your lower arms parallel to the floor as you type. Your upper
arms and shoulders should be relaxed. Then try typing with a light
touch. If you feel any shoulder or neck strain, stop for a while and
check your posture.
•
Position your keyboard in front of your monitor. Putting your
keyboard beside your monitor will make you turn your head while
you type which could add tension to your neck muscles that may
later result in neck strain.
Positioning your mouse
•
The mouse should be placed on the same surface as your keyboard
so that you can reach it with ease.
•
Adjust its position to allow enough space for movement without
making you stretch or lean over.
•
Use your arm to move the mouse. Do not rest your wrist on the
table when moving the mouse.
VT7200-ug-e.book Page 25 Wednesday, July 18, 2001 1:28 PM
25
Connecting peripherals
Setting up your computer is easy. For the most part, you only have
four things to connect: the USB keyboard, the USB mouse, the
monitor, and the power cable.
USB Keyboard
Plug the keyboard cable into the USB port
on the front or rear panel of your computer.
(black port) located
Note: If you are using a PS/2 keyboard, plug the keyboard cable
into the PS/2 keyboard port
panel of your computer.
(purple port) located on the rear
VT7200-ug-e.book Page 26 Wednesday, July 18, 2001 1:28 PM
26
3 Setting up your computer
USB Mouse
Plug the mouse cable into the USB port
the front or rear panel of your computer.
(black port) located on
VT7200-ug-e.book Page 27 Wednesday, July 18, 2001 1:28 PM
27
Note: If you are using a PS/2 mouse, plug the mouse cable into
the PS/2 mouse port
your computer.
(green port) located on the rear panel of
Monitor
To connect a monitor, simply plug the monitor cable into the monitor
port located on the rear panel of your computer.
Note: Refer to the monitor manual for additonal instructions and
information.
VT7200-ug-e.book Page 28 Wednesday, July 18, 2001 1:28 PM
28
3 Setting up your computer
Power cable
Caution: Before you proceed, check the voltage range in your
area. Make sure that it matches your computer’s voltage setting
(refer to page 12 for the location of the voltage selector switch on
the rear panel of your computer). If they don’t match, change
your computer’s voltage setting according to your area’s voltage
range.
Plug the power cable into the power cable socket located on the rear
panel of your computer. Then plug the other end of the power cable
into a power outlet.
VT7200-ug-e.book Page 29 Wednesday, July 18, 2001 1:28 PM
29
Turning on your computer
After connecting the necessary peripherals and plugging in the power
cable, you are now ready to turn the computer on and get to work.
To turn on your computer:
1.
Turn on all peripherals connected to your computer such as the
monitor, printer, fax, speakers, etc.
2.
On the rear panel of your computer, set the voltage selector switch
to the voltage range applicable to your area (a) then turn on the
power switch (b).
VT7200-ug-e.book Page 30 Wednesday, July 18, 2001 1:28 PM
30
3.
3 Setting up your computer
On the front panel of your computer, press the power button.
Important: Make sure that the power cable is properly plugged
into an electrical outlet. If you are using a power strip or an AVR
(Auto-Voltage Regulator), make sure that it is plugged in and
turned on.
VT7200-ug-e.book Page 31 Wednesday, July 18, 2001 1:28 PM
31
Turning off your computer
To turn off your computer, click on the Start button, highlight Shut
Down, select Shut down; then click on OK. You can then turn off all
peripherals connected to your computer.
If you cannot shut down your computer normally, press the power
button for at least four seconds. Quickly pressing the button may put
the computer in Suspend mode only.
VT7200-ug-e.book Page 32 Wednesday, July 18, 2001 1:28 PM
32
3 Setting up your computer
Connecting options
Printer
To connect a printer, plug the printer cable into the parallel port
(burgundy port) located on the rear panel of your computer.
VT7200-ug-e.book Page 33 Wednesday, July 18, 2001 1:28 PM
33
Serial mouse
To connect a serial mouse, plug the serial mouse cable into the serial
port
(teal or turquiose port) located on the rear panel of your
computer.
VT7200-ug-e.book Page 34 Wednesday, July 18, 2001 1:28 PM
34
3 Setting up your computer
Network
You can connect your computer to a Local Area Network (LAN) using a
network cable. To do so, simply plug the network cable into the
network port
on the rear panel of your computer.
Note: Consult your operating system manual for information on
how to configure your network setup.
VT7200-ug-e.book Page 35 Wednesday, July 18, 2001 1:28 PM
35
USB devices
Universal Serial Bus (USB) is a new serial bus design that is capable of
cascading low-/medium-speed peripherals (less than 12 Mbps) such as a
keyboard, mouse, joystick, scanner, printer and modem. With USB,
complex cable connections can be eliminated.
Your computer comes with four USB ports: two each on both the front
and rear panels. These ports allow you to connect additional serial
devices to your computer without using up its system resources.
To connect a USB device, simply plug the device cable into any of the
USB ports
(black port).
VT7200-ug-e.book Page 36 Wednesday, July 18, 2001 1:28 PM
36
3 Setting up your computer
Note: Most USB devices have a built-in USB port which allows you
to connect or daisy-chain more USB devices.
VT7200-ug-e.book Page 37 Wednesday, July 18, 2001 1:28 PM
37
Multimedia devices
You can connect multimedia devices such as microphone, headphone
or earphone, external speakers, audio line-in device and a joystick (for
games). These devices will allow you to take advantage of your
computer’s multimedia features.
Plug the devices in as follows:
•
microphone: connects to the Mic-in jack
(pink jack) located
on the front and rear panel of your computer.
Note: The system has two microphone-in ports (front and rear).
However, you can not use both of them at the same time. The
default setting for your system enables the microphone-in port in
front and disables the one at the back.
•
earphones, headphones: connect to the Headphone-out jack
(lime jack) located on the front panel of your computer
Note: To adjust the volume of the headphones, click on the
Volume icon located on the taskbar at the bottom of your screen.
When the volume control pops up, drag the Volume control lever
to the desired level. You can also use the Volume control button
on the keyboard.
VT7200-ug-e.book Page 38 Wednesday, July 18, 2001 1:28 PM
38
•
3 Setting up your computer
external USB speakers: connect to the Audio-out/Line-out jack
(lime jack) and USB port
(black port) located on the rear
panel of your computer.
VT7200-ug-e.book Page 39 Wednesday, July 18, 2001 1:28 PM
39
•
audio line-in device: connects to the Audio-in/Line-in jack
(light blue jack) located on the rear panel of your computer
•
joystick: connects to the Game/MIDI port
the rear panel of your computer
(gold port) located on
Note: For information on how to configure multimedia devices,
consult the documentation that came with each device.
VT7200-ug-e.book Page 40 Wednesday, July 18, 2001 1:28 PM
40
3 Setting up your computer
VT7200-ug-e.book Page 41 Wednesday, July 18, 2001 1:28 PM
4 Upgrading your
computer
VT7200-ug-e.book Page 42 Wednesday, July 18, 2001 1:28 PM
This chapter contains instructions on how to
upgrade your computer and basic
information about your system boards that
you will find helpful when performing the
upgrade process.
VT7200-ug-e.book Page 43 Wednesday, July 18, 2001 1:28 PM
43
Installation precautions
Before you install any computer component, we recommend that you
read the following sections. These sections contain important ESD
precautions along with preinstallation and post-installation
instructions.
ESD precautions
Electrostatic discharge (ESD) can damage your processor, disk drives,
expansion boards, and other components. Always observe the
following precautions before you install a computer component:
1.
Do not remove a component from its protective packaging until
you are ready to install it.
2.
Wear a wrist grounding strap and attach it to a metal part of the
computer before handling components. If a wrist strap is not
available, maintain contact with the computer throughout any
procedure requiring ESD protection.
Preinstallation instructions
Always observe the following before you install any component:
1.
Turn off your computer and all the peripherals connected to it
before opening it. Then unplug all cables from the power outlets.
2.
Open your computer according to the instructions on page 45.
3.
Follow the ESD precautions described above before handling a
computer component.
4.
Remove any expansion boards or peripherals that block access to
the DIMM sockets or component connector.
5.
See the following sections for specific instructions on the
component you wish to install.
Warning! Not turning off the computer properly before
you start installing the components may cause serious
damage.
Do not attempt the procedures described in the following
sections unless you are a qualified service technician.
VT7200-ug-e.book Page 44 Wednesday, July 18, 2001 1:28 PM
44
4 Upgrading your computer
Post-installation instructions
Observe the following after installing a computer component:
1.
See to it that the components are installed according to the stepby-step instructions in their respective sections.
2.
Replace any expansion boards or peripherals that you removed
earlier.
3.
Replace the computer cover.
4.
Connect the necessary cables and turn on your computer.
VT7200-ug-e.book Page 45 Wednesday, July 18, 2001 1:28 PM
45
Opening your computer
Caution: Before you proceed, make sure that you have turned
off your computer and all peripherals connected to it. Read the
“Preinstallation instructions” on page 43.
You need to open your computer before you can install additional
components. See the following section for instructions.
To remove the side panel
1.
Turn off your computer and unplug all cables.
2.
Place your computer on a flat, steady surface.
3.
Remove the four screws from the rear panel using a screwdriver.
Set the screws aside.
VT7200-ug-e.book Page 46 Wednesday, July 18, 2001 1:28 PM
46
4.
4 Upgrading your computer
Hold one side panel with both hands. Slide it back about an inch
and then gently pull it outward to detach it. Do the same to the
other side.
To reinstall the side panel
1.
Align the side panel's hinges to the housing frame and then push
it in to slide it back into place. Do the same to the other side.
VT7200-ug-e.book Page 47 Wednesday, July 18, 2001 1:28 PM
47
2.
Secure the side panels with four screws.
VT7200-ug-e.book Page 48 Wednesday, July 18, 2001 1:28 PM
48
4 Upgrading your computer
Internal components
The figure below shows what your computer looks like once you
remove the cover:
No.
Component
1
5.25-inch drive bays (three bays)
2
3.5-inch drive bays (two bays)
3
Daughterboard
4
Mainboard
5
Hard disk
6
Expansion slots
7
Power supply
VT7200-ug-e.book Page 49 Wednesday, July 18, 2001 1:28 PM
49
Replacing the hard disk
Follow these steps to replace your computer’s hard disk:
1.
Remove the side panel (see page 45).
2.
Remove the four screws that hold the hard disk to the disk frame.
Set the screws aside.
3.
(a) Detach the power and hard disk cables from the hard disk.
(b) Detach the hard disk from the drive frame.
VT7200-ug-e.book Page 50 Wednesday, July 18, 2001 1:28 PM
50
4 Upgrading your computer
4.
(a) Insert the new hard disk into the frame.
(b) Connect the power and hard disk cables to the new hard disk.
5.
Secure it with four screws.
Note: Make sure that the other ends of the disk cables are
securely connected to their corresponding connectors on the
mainboard.
6.
Reinstall the side panel (see page 46).
VT7200-ug-e.book Page 51 Wednesday, July 18, 2001 1:28 PM
51
Installing an expansion card
Note: Observe the “Installation precautions” on page 43 when
installing or removing a computer component.
To install an expansion card:
1.
Remove the side panel (see page 45).
2.
Locate an empty PCI slot on the mainboard.
3.
Remove the screw that holds the bracket to the computer. Save
the screw.
4.
Pull out the bracket on the housing opposite the selected empty
slot.
5.
Remove the expansion card from its protective packaging.
6.
Align the card with the empty bracket and then insert it into the
slot. Make sure that the card is properly seated.
VT7200-ug-e.book Page 52 Wednesday, July 18, 2001 1:28 PM
52
4 Upgrading your computer
7.
Secure the card to your computer with a screw.
8.
Reinstall the side panel (see page 46).
When you turn on the computer, BIOS (Basic Input/Output System)
automatically detects and assigns resources to the newly-installed
devices.
VT7200-ug-e.book Page 53 Wednesday, July 18, 2001 1:28 PM
53
System boards
Mainboard layout
The mainboard becomes accessible once you open your computer. It
should look like the figure shown below:
VT7200-ug-e.book Page 54 Wednesday, July 18, 2001 1:28 PM
54
4 Upgrading your computer
Label
Component
AGP
AGP slot
BT1
Battery
CN2
PS/2 mouse (upper) and keyboard (lower) ports
CN3
Power connector
CN4
Network (upper) and USB (lower) ports
CN5
Serial port (lower right and left) and parallel port
(upper)
CN6
Memory stick connector
CN7
IDE 2 connector
CN8
IDE 1 connector
CN9
MIDI/game (upper), line-out (left), line-in (middle),
and rear mic-in (right) ports
CN10
Power connector (12 V power)
CN14
CD-in connector
CN15
FDD Connector
CN16
Intrusion connector
CN17
HDD LED connector
CN19
Power button
CN20
Front USB connector
CN21
Power/Suspend LED connector
CN23
EXT PCI slot
CNM1
SmartCard (COM 2) connector1
CNSW1
IDE cold-swap connector
CNX1
Audio FPIO connector
DIMM 1-3
DIMM sockets 1-3
VT7200-ug-e.book Page 55 Wednesday, July 18, 2001 1:28 PM
55
Label
Component
FN1
3-pin CPU fan connector
FN2
3-pin system fan connector
FN3
3-pin system fan connector
JP1
LAN active LED connector
JP3
Model select
JP14
1-2 Clear CMOS
2-3 Normal2
PCI1 to 3
PCI slots 1 to 3
U5
CPU socket
U12
Intel 845 chipset
U16
SMSC chipset
U21
Intel ICH2 chipset
U29
BIOS chipset
1
2
Share connection with serial port 2 (COM 2)
Default value
VT7200-ug-e.book Page 56 Wednesday, July 18, 2001 1:28 PM
56
4 Upgrading your computer
Audio board
The audio board that came with your computer should look like the
figure that follows.
Label
Description
JP1
Audio connector - connects to the AUDIO2
connector of the mainboard
CN1
USB connector - connects to the USB2 connector of
the mainboard
CN2 and CN3
USB ports
JK1
Microphone-in port (front)see note
JK2
Audio-out port
Note: The system has two microphone-in ports (front and rear).
However, you can not use both of them at the same time. The
default setting for your system enables the microphone-in port in
front and disables the one at the back.
VT7200-ug-e.book Page 57 Wednesday, July 18, 2001 1:28 PM
57
Installing additional memory
The three 168-pin sockets on the mainboard support Synchronous
Dynamic Random Access Memory (SDRAM)-type DIMMs. You may
install 32-MB, 64-MB, 128-MB, 256-MB, 512-MB or 1-GB single and
double density DIMMs for a maximum memory capacity of 3 GB.
The SDRAM DIMMs should work under 3.3 volts; 5-volt memory devices
are not supported. PC-100 (100MHz) and PC-133 (133 MHz) SDRAM are
supported. Contact your dealer for qualified DIMM vendors.
Caution: Do not install and use both PC-100 and PC-133 SDRAM
together. Such a combination might cause your computer to
malfunction.
Each of the DIMM sockets is independent from each other. This
independence allows you to install DIMMs with different capacities to
form different configurations.
To remove a DIMM
Note: Observe the “Installation precautions” on page 43 when
installing or removing a computer component. Also, make sure
that you have removed the computer cover (see page 45).
1.
Press the holding clips on both sides of the DIMM socket outward
to release the DIMM (a).
2.
Gently pull the DIMM out of the socket (b).
VT7200-ug-e.book Page 58 Wednesday, July 18, 2001 1:28 PM
58
4 Upgrading your computer
To install a DIMM
Note: Observe the “Installation precautions” on page 43 when
installing or removing a computer component. Also, make sure
that you have removed the computer cover (see page 45).
1.
Open the clips on the socket.
2.
Align the DIMM with the socket (a).
3.
Press the DIMM into the socket until the clips lock onto the DIMM
(b).
Note: The DIMM sockets are slotted to ensure proper installation.
If you insert a DIMM but it does not fit easily into the socket, you
may have inserted it incorrectly. Turn the DIMM and try to insert it
again.
To reconfigure your computer
Your computer automatically detects the amount of memory installed.
Run the BIOS utility to view the new value for total system memory
and make a note of it. For more information on BIOS, refer to the
Veriton 7200 online guide (see “Accessing the online guide” on page
6).
VT7200-ug-e.book Page 59 Wednesday, July 18, 2001 1:28 PM
5 Software
VT7200-ug-e.book Page 60 Wednesday, July 18, 2001 1:28 PM
This chapter describes the applications that
came with your computer.
VT7200-ug-e.book Page 61 Wednesday, July 18, 2001 1:28 PM
61
Your computer comes with the following applications:
•
Acrobat® Reader™
•
LDCM
•
Norton AntiVirus
•
NTI CD-Maker 2000
•
PowerDVD
•
VariSpeed
•
BIOS utility
All of the applications that came with your computer are very easy to
use. However, if you need more help and information, you may refer
to the online help documentation provided in each software
application.
VT7200-ug-e.book Page 62 Wednesday, July 18, 2001 1:28 PM
62
5 Software
Acrobat Reader
Acrobat Reader is a software that lets you view, navigate, browse and
print Adobe Portable Document Format (PDF) files on all major
computer platforms. Acrobat Reader can open your document across a
broad range of hardware and software, and it will look exactly as you
intended - with layout, fonts, links and images intact.
To run Acrobat Reader, double-click the Acrobat Reader icon on your
Windows's desktop.
For more information about Acrobat Reader, you may refer to its Help
menu.
VT7200-ug-e.book Page 63 Wednesday, July 18, 2001 1:28 PM
63
LDCM
LANDesk Client Manager (LDCM) allows desktop management via the
Web, standard network, or dial-up connections. It is compatible with
the leading management specifications, such as Wired for
Management 2.0, Desktop Management Interface (DMI) v2.0, and
others.
LDCM may not have been preloaded on your computer. As such, you
will need to install it. To do so,
1.
Make sure that your computer is turned on.
2.
Insert the Programs CD that came with your computer into the CD
or DVD drive.
3.
Follow all onscreen instructions until you finish the installation.
Caution: Make sure that the CD is properly inserted into the CD
or DVD drive. Improper insertion may damage both the CD and
the CD or DVD drive. For instructions on how to insert a CD into
your computer's CD or DVD drive, see page 19.
Note: LDCM currently supports Windows Me and Windows 2000.
To run LDCM:
1.
Double-click the LDCM icon on your Windows desktop.
2.
Follow all onscreen instructions.
For more information on how to use the LDCM, refer to the LDCM Help
menu.
VT7200-ug-e.book Page 64 Wednesday, July 18, 2001 1:28 PM
64
5 Software
Norton AntiVirus
Norton AntiVirus is an anti-virus software which finds and repairs
infected files, protects against viruses to keep your computer data safe
and secure. It also scans incoming email attachments for viruses. It
provides useful virus detection and repair facilities.
To install Norton AntiVirus:
1.
Double-click the Norton AntiVirus icon on your Windows desktop.
2.
Follow all onscreen instructions until you finish installation.
Note: After you finish installing the Norton AntiVirus software,
the system will automatically delete the Norton AntiVirus installer
icon from your Windows desktop.
For more information about Norton AntiVirus, you may refer to the
Norton AntiVirus Help menu.
VT7200-ug-e.book Page 65 Wednesday, July 18, 2001 1:28 PM
65
NTI CD-Maker 2000 (for models with
CD-RW)
The NTI CD-Maker 2000 is a CD-Recording software which allows you
to create and copy audio, data and videos to CD-RW discs.
To run NTI CD-Maker 2000:
1.
Double-click the NTI CD-Maker 2000 icon on your Windows
desktop.
2.
Follow all onscreen instructions.
For more information on how to use the NTI CD-Maker 2000, refer to
the NTl CD-Maker 2000 Help menu.
VT7200-ug-e.book Page 66 Wednesday, July 18, 2001 1:28 PM
66
5 Software
PowerDVD (for models with DVD)
PowerDVD is a high-quality, pure software DVD player which brings
high-quality movies and karaoke to your multimedia PC. You can play
back high resolution DVD titles or MPEG-2 files with MPEG-2 video and
Dolby Digital (AC-3) audio. PowerDVD provides a complete set of
commands for navigation and advanced features such as multi-angle
switching, multi-language and multi-subtitle selection, and parental
control. It also has the i-Power Internet Enabling feature, which links
to online DVD resources via the Power DVD Desktop Portal Page.
To run PowerDVD:
1.
Double-click the PowerDVD icon on your Windows desktop.
2.
Follow all onscreen instructions.
For more information about PowerDVD, refer to the PowerDVD Help
menu.
VT7200-ug-e.book Page 67 Wednesday, July 18, 2001 1:28 PM
67
VariSpeed (Windows Me only)
VariSpeed is a utility program which allows you to control the CD-ROM
speed to reduce its noise level.
To set the speed of the CD-ROM drive, double-click on the VariSpeed
icon on the taskbar and choose the Set Speed tab. The Set Speed
screen will appear. Drag the lever to the desired level.
Note: This utility is available for AOpen CD-ROM drives only.
VT7200-ug-e.book Page 68 Wednesday, July 18, 2001 1:28 PM
68
5 Software
BIOS utility
The BIOS utility is a hardware configuration program built into your
computer's Basic Input/Output System (BIOS). Since most computers
are already properly configured and optimized, there is no need to run
this utility. However, if you encounter configuration problems and get
the "Run Setup" message, you will need to run this utility.
Note: Before you run BIOS, make sure that you have saved all
open files. The computer reboots immediately after you exit
Setup.
To run the BIOS utility, press the key combination Ctrl+Alt+Esc. For
information about BIOS and how to configure your computer, refer to
the Veriton 7200 online guide (see “Accessing the online guide”on
page 6).
VT7200-ug-e.book Page 69 Wednesday, July 18, 2001 1:28 PM
69
Reinstalling programs
If you uninstall one of the preinstalled programs and want to reinstall
it, do the following:
1.
Make sure that the system is turned on.
2.
Insert the Programs CD into the CD or DVD drive.
3.
Select the application that you want to reinstall.
4.
Follow all onscreen instructions until you finish the installation.
VT7200-ug-e.book Page 70 Wednesday, July 18, 2001 1:28 PM
70
5 Software
VT7200-ug-e.book Page 71 Wednesday, July 18, 2001 1:28 PM
6 Q&A
VT7200-ug-e.book Page 72 Wednesday, July 18, 2001 1:28 PM
This chapter tells you what to do in case
your computer is not working properly.
However, if a more serious problem arises,
contact your dealer or the technical support
center (www.acersupport.com) for
assistance.
VT7200-ug-e.book Page 73 Wednesday, July 18, 2001 1:28 PM
73
The following questions are possible situations that may arise during
the use of your computer and each is followed by easy answers and
solutions to the situation.
Q: I pressed the power switch but the system did not boot up.
A: Check the LED located above the power switch.
If the LED is not lit, no power is being applied to the system. Do any of
the following:
•
Check if the voltage selector switch located on the rear panel of
the computer is set to the correct voltage.
•
Check if the main power switch located on the rear panel of the
computer is turned ON (1). See “Turning on your computer” on
page 29 for the location of the main power switch on your
computer.
•
Check if you plugged the power cable properly into an electrical
outlet.
•
If you are using a power strip or AVR, make sure that it is plugged
in and turned on.
If the LED is lit, check the following:
•
Is a nonbootable (nonsystem) diskette in the floppy drive? If yes,
remove or replace it with a system diskette and press Ctrl + Alt +
Del to restart your computer.
•
The operating system files may be damaged or missing. Insert the
startup disk you created during Windows setup into the floppy
drive and press Ctrl + Alt + Del to restart your computer. This will
automatically diagnose your system and make necessary fixes.
However, if the diagnostic utility still reports a problem, then you
may have to insert the Recovery CD that came with your system to
restore it to its original factory default settings.
Caution: Using the Recovery CD will erase all files previously
saved in your computer so make sure to back up your important
files before starting the recovery process. For more information
about recovering your system, refer to the Veriton 7200 online
guide.
VT7200-ug-e.book Page 74 Wednesday, July 18, 2001 1:28 PM
74
6Q&A
Q: Nothing appears on the screen.
A: Your computer’s power management function automatically blanks
the screen to save power. Just press any key to turn the display back
on.
If pressing a key does not work, you can restart your computer. If
restarting your computer does not work, contact your dealer or the
technical support center for assistance.
Q: The printer does not work.
A: Do the following:
•
Make sure that the printer is connected to a power outlet and that
it is turned on.
•
Make sure that the printer cable is connected securely to the
system’s parallel port and the corresponding port on the printer.
See “Printer” on page 32 for information on how to connect the
printer to your computer.
•
For additional information concerning the printer, refer to the
printer’s documentation.
Q: No sound comes out from the computer.
A: Check the following:
•
The volume may be muted. Look for the Volume icon on the
taskbar. If it is crossed-out, click on the icon and deselect the
Mute option. You can also press the volume control/mute knob
on your USB keyboard to toggle from mute to sound on.
•
If headphones, earphones, or external speakers are connected to
the line-out jack of your computer, the internal or built-in speakers
are automatically turned off.
VT7200-ug-e.book Page 75 Wednesday, July 18, 2001 1:28 PM
75
Q: System cannot read diskette, hard disk, CD or DVD information.
A: Check the following:
•
Make sure that you are using the correct type of disc or diskettes.
See “Disk drives” on page 18.
•
Check if the diskette is formatted correctly. If not, format it again.
Caution: If you reformat a diskette, you will lose all data on it.
•
Make sure the diskette, CD or DVD is inserted into the drive
correctly.
•
Check if the CD or DVD is clean and not scratched.
•
Check your drive by using a good (i.e., undamaged) diskette or a
good disc. If your floppy drive, CD or DVD drive can not read the
information on the good diskette, CD or DVD there may be a
problem with the drive. Contact your dealer or technical support
center for assistance.
Q: System cannot write diskette, hard disk or disc.
A: Check the following:
•
Make sure the diskette or hard disk is not write-protected. See
“Disk drives” on page 18.
•
Make sure that you are using the correct type of diskette. See
“Disk drives” on page 18.
•
Check if the diskette is formatted correctly. If not, format it again.
Caution: If you reformat a diskette, you will lose all data on it.
VT7200-ug-e.book Page 76 Wednesday, July 18, 2001 1:28 PM
76
6Q&A
VT7200-ug-e.book Page 77 Wednesday, July 18, 2001 1:28 PM
77
Index
caps lock 14
cursor keys 15
function key 14
internet/suspend keys 16
multimedia keys 16
num lock 15
palm rest 15
programmable keys 16
scroll lock 15
volume control/mute 15
Windows logo key 15
A
accessing the online guide
applications 61
6
B
BIOS utility
68
C
computer maintenance 4
cleaning 4
servicing 4
connecting options
multimedia devices 37
audio line-in device 39
earphones/headphones 37
external speakers 37
joystick 37
microphone 37
network 32, 34
printer 32
serial mouse 33
M
mouse 17
buttons 17
clicking 17
double-click 17
ratchet wheel 17
Q
Q&A
D
disk drives 18
CD-ROM/DVD-ROM/CD-RW drive
inserting CDs/DVDs 19
taking care CDs/DVDs 20
floppy drive 18
not write-protect 18
write-protect 18
hard disk 20
F
features 9
connectivity 9
multimedia 9
performance 9
front panel 10
I
internal components
48
K
keyboard 14
application key
15
73
blank screen 74
no audio 74
no sound 74
printer not working 74
system cannot read disk 75
system cannot write to disk 75
system did not boot up 73
R
rear panel 12
remove the side panel
45
S
safety instructions iv
setting up computer 23, 25
area 23
chair 23
connecting peripherals
external monitor 27
power cable 28
USB keyboard 25
USB mouse 26
keyboard 24
monitor 24
mouse 24
software 61
Acrobat Reader 62
LDCM 63
VT7200-ug-e.book Page 78 Wednesday, July 18, 2001 1:28 PM
78
Norton AntiVirus 64
NTI CD-Maker 2000 65
PowerDVD 66
reinstalling programs 69
VariSpeed 67
system boards 53
audio board 56
mainboard 53
T
turning off computer 31
software shutdown 31
suspend mode 31
turning on computer 29
power button 29
Index
U
upgrade
add memory 57
install DIMM 58
reconfigure computer 58
computer 53, 57
installation precautions 43
ESD 43
post-installation 44
preinstallation 43
open computer
reinstall side panel 46
remove side panel 45
replace components 53, 57
USB devices 35
Download PDF

advertising