Acer 7315 Personal Computer User Manual

Aspire 7715Z/7315 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire 7715Z/7315 service guides.
Date
II
Chapter
Updates
Copyright
Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
TouchPad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
System Utilities
21
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
HM70-MV Intel BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
BIOS Flash Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
WinFlash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Remove HDD/BIOS Password Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Machine Disassembly and Replacement
43
Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Removing the SD Dummy Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Removing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
VII
Table of Contents
Removing the Left Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Removing the Right Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Removing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Removing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Removing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Removing the CPU Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Removing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Removing the LCD Brackets and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Removing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Replacing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Replacing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Replacing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Replacing the CPU Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Replacing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Replacing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Replacing the Right Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Replacing the Left Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Replacing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Replacing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Replacing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Replacing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Replacing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Replacing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Replacing the SD Dummy Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Troubleshooting
123
Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
TouchPad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
VIII
Table of Contents
Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Post Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Sec: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Memory: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
BDS & Specific action: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
Each PEIM entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
Each Driver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
Each SmmDriver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . .144
Jumper and Connector Locations
145
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
LS-4852P ODD Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
LS-4853P Battery Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
LS-4854P Lid Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
Clear CMOS Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
FRU (Field Replaceable Unit) List
151
Aspire 7715Z/7315 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
Rear Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Aspire 7715Z/7315 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Screw List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
Model Definition and Configuration
164
Aspire 7315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
Aspire 7715Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
Test Compatible Components
181
Microsoft® Windows® 7 Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
Online Support Information
185
Index
187
IX
Table of Contents
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many features:
NOTE: Items denoted with an (*) are only available for selected models.
Operating System
•
Genuine Windows® 7™
Platform
•
Intel® Pentium® mobile processor*
•
Intel® Celeron® mobile processor*
•
Mobile Intel® GL40 Express Chipset
System Memory
•
Dual-channel support
•
Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules*
•
Up to 2 GB of DDR3 1066 MHz memory, upgradeable to 4 GB using two soDIMM modules*
Display
•
17" HD+ 1600 x 900
•
16:9 aspect ratio
Graphics
•
Mobile Intel® GL40 Express Chipset
Storage subsystem
•
2.5" hard disk drive
•
DVD-Super Multi double-layer drive
•
Multi-in-1 card reader
•
Two built-in stereo speakers
•
High-definition audio support
•
MS-Sound compatible
Audio
Dimensions and Weight
•
Chapter 1
410.5 (W) x 268 (D) x 26.8/39.6 (H) mm (16 x 10.45 x 1.04/1.54 inches)
1
•
3.30 kg (7.29 lbs.) with one HDD and 6-cell battery pack
Communication
•
Integrated Acer Crystal Eye webcam*
•
WLAN:
•
•
Acer InviLink™ 802.11b/g/Draft-N*
•
Acer InviLink™ 802.11b/g*
LAN: Fast Ethernet; Wake-on-LAN ready
Privacy control
•
BIOS user, supervisor, HDD passwords
•
Kensington lock slot
Power subsystem
•
ACPI 3.0
•
48.8 W 4400 mAh
•
3-pin 65 W AC adapter
•
ENERGY STAR®*
Special keys and controls
•
99-/100-/103-key keyboard
•
Touchpad pointing device
I/O interface
•
USB 2.0 port
•
External display (VGA) port
•
Headphones/speaker/line-out jack
•
Microphone-in jack
•
Ethernet (RJ-45) port
•
DC-in jack for AC adapter
Environment
•
•
2
Temperature:
•
Operating: 5 °C to 35 °C
•
Non-operating: -20 °C to 65 °C
Humidity (non-condensing):
•
Operating: 20% to 80%
•
Non-operating: 20% to 80%
Chapter 1
System Block Diagram
Chapter 1
3
Your Acer Notebook tour
Front View
No.
4
Icon
Item
Description
1
Acer Crystal Eye
webcam
Web camera for video communication
(for selected models).
2
Display screen
Also called Liquid-Crystal Display (LCD),
displays computer output.
3
Touchpad toggle
Turns the internal touchpad on and off.
Power button
Turns the computer on and off.
Wireless LAN
communication
button/indicator
Enables/disables the wireless LAN function.
Indicates the status of wireless LAN
communication.
4
Speakers
Left and right speakers deliver stereo audio
output.
5
Keyboard
For entering data into your computer.
6
TouchPad
Touch-sensitive pointing device which functions
like a computer mouse.
Chapter 1
No.
Icon
Item
Description
7
Click buttons (left
and right)
The left and right buttons function like the left
and right mouse buttons.
8
Palmrest
Comfortable support area for your hands when
you use the computer.
9
HDD
Indicates when the hard disk drive is active.
Num Lock
Lights up when Num Lock is activated.
Caps Lock
Lights up when Caps Lock is activated.
Closed Front View
No.
1
2
Icon
Item
Description
Power
Indicates the computer's power status.
Battery1
Indicates the computer's battery status.
1. Charging: The light shows amber when the
battery is charging.
2. Fully charged: The light shows green when
in AC mode.
5-in-1 card
reader
Accepts Secure Digital (SD), MultiMediaCard
(MMC), Memory Stick (MS), Memory Stick
PRO (MS PRO), xDPicture Card (xD).
NOTE: Push to remove/install the card.
Only one card can operate at any
given time.
1
NOTE: 1 The front panel indicators are visible even when the computer cover is closed
Chapter 1
5
Rear View
No.
1
Item
Ventilation slots
Description
Enable the computer to stay cool, even after prolonged use.
Left View
No.
6
Icon
Item
Description
1
DC-in jack
Connects to an AC adapter
2
Ethernet (RJ-45)
port
Connects to an Ethernet 10/100-based
network.
3
External display
(VGA) port
Connects to a display device
(e.g. external monitor, LCD projector).
4
USB 2.0 ports
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
5
Microphone-in
jack
Accepts input from external microphones.
Headphones/
speaker/line-out
jack
Connects to audio line-out devices
(e.g. speakers, headphones).
Chapter 1
Right View
No.
Item
Description
1
Optical drive
Internal optical drive; accepts CDs or DVDs.
2
Optical disk access
indicator
Lights up when the optical drive is active.
3
Optical drive eject button
Ejects the optical disk from the drive.
4
Emergency eject hole
Ejects the optical drive tray when the computer is turned
off.
Note: Insert a paper clip into the emergency eject hole to
eject the optical drive tray when the computer is off.
5
Kensington lock slot
Connects to a Kensington-compatible computer security
lock.
Note: Wrap the computer security lock cable around an
immovable object such as a table or handle of a locked
drawer. Insert the lock into the notch and turn the key to
secure the lock. Some keyless models are also available.
Bottom View
No.
Icon
Item
Description
1
Battery bay
Houses the computer's battery pack.
2
Battery release
latch
Releases the battery for removal.
Chapter 1
7
No.
Icon
Item
Description
3
Battery lock
Locks the battery in position.
4
Hard disk baySecondary
Houses the computer's hard disk (secured
with screws) (for certain models only).
5
Hard disk bayMain
Houses the computer's hard disk (secured
with screws).
6
Memory
compartment
Houses the computer's main memory.
7
Ventilation slots
and cooling fan
Enable the computer to stay cool, even after
prolonged use.
Note: Do not cover or obstruct the fan opening.
Indicators
The computer has several easy-to-read status indicators. The front panel indicators are visible even when the
computer cover is closed.
Icon
8
Function
Description
Power
Indicates the computer's power status.
Battery
Indicates the computer's battery status.
NOTE: 1. Charging: The light shows amber when
the battery is charging. 2. Fully charged: The light
shows green when in AC mode.
HDD
Indicates when the hard disk drive is active.
Num Lock
Lights up when Num Lock is activated.
Caps Lock
Lights up when Caps Lock is activated.
Chapter 1
TouchPad Basics
The following items show you how to use the TouchPad:
•
Move your finger across the TouchPad (1) to move the cursor.
•
Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the TouchPad is the same as clicking the left button.
Function
Left Button (2)
Right Button (3)
Main TouchPad (1)
Execute
Quickly click twice.
Tap twice (at the same speed
as double-clicking a mouse
button).
Select
Click once.
Tap once.
Drag
Click and hold, then use
finger on the TouchPad to
drag the cursor.
Tap twice (at the same speed
as double-clicking a mouse
button); rest your finger on
the TouchPad on the second
tap and drag the cursor.
Access
context menu
Click once.
NOTE: When using the TouchPad, keep it - and your fingers - dry and clean. The TouchPad is sensitive to
finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not
increase the TouchPad’s responsiveness.
Chapter 1
9
Using the Keyboard
The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function
and special keys.
Lock Keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed are in uppercase.
Num Lock
When Num Lock is on, the embedded keypad is in numeric mode. The keys
function as a calculator (complete with the arithmetic operators +, -, *, and /). Use
this mode when you need to do a lot of numeric data entry. A better solution
would be to connect an external keypad.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
10
Num Lock on
Num Lock off
Number keys on
embedded keypad
Type numbers in a normal manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using cursorcontrol keys.
Hold <Fn> while using cursorcontrol keys.
Main keyboard keys
Hold <Fn> while typing letters on
embedded keypad.
Type the letters in a normal
manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Description
Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;
it launches the Start menu. It can also be used with other keys to provide a variety of
functions:
<
>:
<
>
+ <D>: Display the desktop
<
>
+ <E>: Open Windows Explore
<
>
+ <F>: Search for a file or folder
<
>
+ <G>: Cycle through Sidebar gadgets
<
>
+ <L>: Lock your computer (if you are connected to a network domain), or
switch users (if you're not connected to a network domain)
<
>
+ <M>: Minimizes all windows
<
>
+ <R>: Open the Run dialog box
<
>
+ <T>: Cycle through programs on the taskbar
<
>
+ <U>: Open Ease of Access Center
<
>
+ <X>: Open Windows Mobility Center
<
>
+ <BREAK>: Display the System Properties dialog box
<
>
+ <SHIFT+M>: Restore minimized windows to the desktop
<
>
+ <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D
<
>
+ <SPACEBAR>: Bring all gadgets to the front and select Windows Sidebar
Open or close the Start menu
<CTRL> + <
>
<CTRL> + <
>
+ <F>: Search for computers (if you are on a network)
+ <TAB>: Use the arrow keys to cycle through programs on the
taskbar by using Windows Flip 3-D
Note: Depending on your edition of Windows 7, some shortcuts may not function as
described.
Application
key
Chapter 1
This key has the same effect as clicking the right mouse button; it opens the
application's context menu.
11
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hotkey
12
Icon
Function
Description
<Fn> + <F4>
<Fn> + <F4>
Sleep
Puts the computer in Sleep mode.
<Fn> + <F5>
<Fn> + <F5>
Display toggle
Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn> + <F6>
Screen blank
Turns the display screen backlight off to save
power. Press any key to return.
<Fn> + <F8>
Speaker toggle
Turns the speakers on and off.
<Fn> ++ <
<<Fn>
>
<Fn>
> +< >
Volume up
Increases the sound volume.
<Fn> +
+<
<<Fn>
>
<Fn>
> +< >
Volume down
Decreases the sound volume.
<Fn> + <<Fn>
> +< >
Brightness up
Increases the screen brightness.
<Fn> + <<Fn>
> +< >
Brightness down
Decreases the screen brightness.
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
CPU
•
Intel® Pentium® mobile processor*
•
Intel® Celeron® mobile processor*
Type
Intel Mobile Memron uPGA
Core Logic
Mobile Intel® GL40 Express Chipset
CPU Package
Micro uPGA-478 Package
Power
65 Watts
On-die Cache
4MB L2 cache
Front Side Bus
667/800/1066MHz
Processor Specifications
CPU
Speed
Item
Cores
Bus
Speed
Mfg
Tech
Cache
Size
Package
Core
Voltage
Acer P/N
T1600
1.66 GHz
2
667 MHz
65 nm
1 MB
PGA
1.075V1.175V
KC.16001.CMT
T1700
1.83 GHz
2
667 MHz
65 nm
1 MB
PGA
1.075V1.175V
KC.17001.CMT
CM575
2.0 GHz
2
667 MHz
65 nm
1 MB
PGA
0.951.30V
KC.N0001.575
CM585
2.16 GHz
2
667 MHz
65 nm
1 MB
PGA
0.951.30V
KC.N0001.585
CM900
2.2 GHz
2
800 MHz
N/A
1 MB
PGA
N/A
KC.N0001.900
PMDT4300
2.16 GHz
2
667 MHz
N/A
1 MB
PGA
N/A
KC.34001.DT
P
PMDT4400
2.0 GHz
2
800 MHz
N/A
1 MB
PGA
N/A
KC.42001.DT
P
CPU Fan True Value Table
Fan On Temp (°C)
Fan Speed (rpm)
SPL Spec (dBA)
45
3000
28
50
3300
31
55
3700
34
65
4100
37
75
4500
40
80
4500
40
•
Throttling 50%: On=99°C, Off=96°C
•
OS Shutdown: 105°C
•
H/W Shutdown: 110°C
Northbridge
Item
Specification
Chipset
Intel Cantiga GM45/GL40
Package
uFCBGA-1329
Chapter 1
13
Southbridge
Item
Specification
Chipset
ICH9-M
Package
BGA-676
BIOS
Item
Specification
BIOS vendor
Insyde BIOS
BIOS Version
V0.06-T02
BIOS ROM type
Flash
Features
•
Flash ROM 1MB
•
Supports ISIPP
•
Supports Acer UI
•
Supports multi-boot
•
Suspend to RAM (S3)/Disk (S4)
•
Various hot-keys for system control
•
Supports SMBUS 2.0, PCI2.3
•
ACPI 2.0 compliance with Intel Speed Step support C1, C2,
C3, C4 and S3, S4 for mobile CPU
•
DMI utility for BIOS serial number configurable/asset tag
•
Supports PXE
•
Supports Y2K solution
•
Supports Win Flash Wake on LAN from S3
•
Wake on LAN form S4 in AC mode
•
System information
System Memory
Item
14
Specification
Memory controller
ICH9-M
Memory size
4GB maximum
DIMM socket number
2
Supports memory size per socket
2GB
Supports maximum memory size
4GB (total)
Supports DIMM type
200-pin +1.8V DDRII
Supports DIMM Speed
667/800 MHz
Supports DIMM voltage
1.8V
Chapter 1
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
512MB
512MB
0MB
1024MB
1024MB
0MB
2048MB
2048MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
512MB
2048MB
2560MB
1024MB
0MB
1024MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
1024MB
2048MB
3072MB
2048MB
0MB
2048MB
2048MB
512MB
2560MB
2048MB
1024MB
3072MB
2048MB
2048MB
4096MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
LAN Interface
Item
Specification
LAN Chipset
Atheros AR8132L
LAN connector type
RJ-45
LAN connector location
Right side
Feature
Support for 10/100
Wireless Module 802.11b/g/Draft-N
Item
Manufacturer
Chapter 1
Specification
•
Foxconn FOX_ATH_XB63 Foxconn Atheros XB63
minicard b/g
•
Foxconn Wireless LAN Broadcom 4312 minicard b/g
15
Hard Disk Drive Interface
Item
Specification
Vendor & Model
Name
Seagate
ST9500325AS
ST9250315AS
Seagate
ST9320320AS
ST9160310AS
Toshiba
MK3255GSX
MK2555GSX
MK1655GSX
Western Digital
WD5000BEVT
WD3200BEVT
WD2500BEVT
WD1600BEVT
Capacity (MB)
500, 250
320, 160
320, 250, 160
500, 320, 250,
160
Bytes per sector
512
512
512
512
Data heads
4, 2
4, 2
4, 2, 2
4, 4, 3, 2
Disks
2, 1
2 or 1, 1
2, 1, 1
2, 2, 2, 1
Spindle speed
(RPM)
5400
5400
5400
5400
8 MB
8 MB
8 MB
Drive Format
Performance Specifications
Buffer size
8 MB
Interface
SATA
SATA
SATA
SATA
Internal transfer
rate (Mbits/sec,
max)
352
395~952
(typical)
850 Mbits/s
maximum
I/O data transfer
rate
(Mbytes/sec
max)
150
300
300 maximum
5V ±5%
5V ±5%
5V ±5%
DC Power Requirements
Voltage
tolerance
16
5V ±5%
Chapter 1
Super-Multi Drive Module
Item
Specification
Vendor & model
name
HLDS GT20N
Sony AD7580S
Performance
Specification
With CD Diskette
With DVD Diskette
With CD Diskette
With DVD Diskette
Transfer rate (MB/
sec)
Sustained:
3,600 KB/s (24x)
max.
Sustained:
11.08 Mbytes/s
(8x) max.
Sustained:
1,571 (typical)
Sustained:
10,993 (typical)
Buffer Memory
2 MB
Interface
SATA
Applicable disc
formats
DVD-ROM:
4.7GB (Single Layer)
8.5GB (Dual Layer)
DVD-R:
3.95GB (Ver. 1.0: read only)
4.7GB (Ver. 2.0 for Authoring: read only)
4.7GB (Ver. 2.1 for General: read & write)
(DL) 8.5GB (Ver. 3.0)
DVD-RW:
4.7GB (Ver. 1.2/ Rev 1.0, 2.0, 3.0)
DVD-RAM: 1.46GB/side, 4.7GB/side
(Ver. 2.2)
DVD+R: 4.7GB (Ver. 1.3)
(DL) 8.5GB (Ver. 1.1)
DVD+RW:
4.7GB (Vol.1 Ver.1.3)
CD-ROM Mode-1 data disc
CD-ROM Mode-2 data disc
CD-ROM XA, CD-I, Photo-CD MultiSession, Video CD
CD-Audio Disc
Mixed mode CD-ROM disc (data and
audio)
CD-Extra
CD-Text
CD-R (Conforming to “Orange Book Part
2”: read & write)
CD-RW (Conforming to “Orange Book
Part 3”: read & write)
Loading mechanism
DVD Read:
DVD-ROM (DVD-5, DVD-9, DVD-10, DVD18), DVD-Video, DVD-Audio, SACD (Hybrid),
UDF DVD, DVD-R, DVD-R DL, DVD-R 3.95
GB, DVD-R Authoring, DVD-R Multi-Border,
DVD-RW, DVD+R, DVD+R DL, DVD+R
Multi-Session, DVD+RW, DVD-RAM V1.0,
DVDRAM
V2.0 & 2.1 &2.2.
CD Read:
CD-DA, CD-ROM Mode-1, CD-ROM/XA
Mode-2 Form-1 and Mode-2 Form-2, CD-i,
CD-i
Bridge, Video-CD (MPEG-1), Karaoke CD,
Photo-CD, Enhanced CD, CD Plus, CD
Extra, itrax
CD, CD-Text, UDF CD, CD-R, and CD-RW
DVD Write:
DVD Data & Video
CD Read:
CD-DA, CD-ROM Mode-1, CD-ROM/XA
Mode-2 Form-1 and Mode-2 Form-2, CD-i,
VideoCD, CD-Text
Drawer (Solenoid Open)
Tact SW (Open)
Emergency Release (draw open hole)
Power Requirement
Input Voltage
DC 5 V +/- 5%
Audio Interface
Item
Specification
Chipset
Realtek ALC272X-GR
Features
High Definition Audio Codec with Dolby Digital Live
Chapter 1
17
Power and Keyboard Controller
Item
Specification
Controller
ENE KB926
Total number of keypads
99-/100-/103-key keyboard
Windows logo key
Yes
Hotkeys
See “Hot Keys” on page 12.
Battery
Specification
Item
18
6 Cell
Vendor & model name
SANYO/SONY/PANASONIC/SAMSUNG/SIMPLO AS2009A
Battery Type
Li-ion
Pack capacity
4400 mAh
Normal Voltage
2.2 Ah
Package configuration
3S2P
Chapter 1
LCD 17”
Item
Specification
Vendor/model name
CMO N173O6-L02
Screen Diagonal (mm)
439.4
Display Area (mm)
382.08 x 214.92
Display resolution (pixels)
1600 x 900
Pixel Pitch
0.2388
Display Mode
Normal
Typical White Luminance (cd/m2)
(also called Brightness)
220
Contrast Ratio
600:1
Response Time (Optical Rise
Time/Fall Time) msec
8
Typical Power Consumption
(watt)
7
Weight
580 max.
Physical Size (mm)
398.1 x 232.8 x 5.5
Electrical Interface
LVDS
Support Color
262K
Viewing Angle (up/down/right/
left)
20/45/45/45
Temperature Range (°C)
Operating
Storage (shipping)
0 to +50
-20 to +60
Card Reader
Item
Specification
Part Name
RealTek RT5159
Package
5-in-1 card reader
General Features
•
PCI-E interface
•
Push-push type
•
Dummy card
Chapter 1
19
20
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility
There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.
Follow these instructions:
•
To choose a menu, use the left and right arrow keys.
•
To choose an item, use the up and down arrow keys.
•
To change the value of a parameter, press F5 or F6.
•
A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
•
Press Esc while you are in any of the menu options to go to the Exit menu.
•
In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
Chapter 2
21
HM70-MV Intel BIOS
Information
The Information screen displays a summary of your computer hardware information.
Information
Main
InsydeH20 Setup Utility
Security
Power
Boot
Exit
Advanced
CPU Type
CPU Speed
Intel(R) Pentium(R) Dual
2.16GHz
HDD Model Name:
HDD Serial Number:
HDD Model Name:
HDD Serial Name:
ATAPI Model Name:
WDC WD5000BEVT-22ZAT0
WD-WXNY08SP8652
None
System BIOS Version:
VGA BIOS Version:
Serial Number:
Asset Tag Number:
Product Name:
Manufacturer Name:
UUID:
V0.09-T1
Intel V1704
F1 Help
ESC Exit
CPU
Rev. 3.5
T3400
@ 2.16GHz
MATSHITADVD-RAM UJ880AS
Aspire 7715Z/7315
Acer
63623032-6261-3964-6338-00235A495964
Select Item
Select Menu
F5/F6
Enter
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ according to model.
The table below describes the parameters in this screen.
Parameter
22
Description
CPU Type
This field shows the CPU type and speed of the system.
CPU Speed
This field shows the speed of the CPU.
HDD Model Name
This field shows the model name of HDD installed on primary IDE
master.
HDD Serial Number
This field displays the serial number of HDD installed on primary IDE
master.
ATAPI Model Name
This field shows the model name of the Optical device installed in
the system.
System BIOS Version
Displays system BIOS version.
VGA BIOS Version
This field displays the VGA firmware version of the system.
Serial Number
This field displays the serial number of this unit.
Asset Tag Number
This field displays the asset tag number of the system.
Product Name
This field shows product name of the system.
Manufacturer Name
This field displays the manufacturer of this system.
UUID
Universally Unique Identifier (UUID) is an identifier standard used in
software construction, standardized by the Open Software
Foundation (OSF) as part of the Distributed Computing Environment
(DCE).
Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.
Information
Main
InsydeH20 Setup Utility
Security
Boot
Power
Exit
Advanced
Rev. 3.5
Item Specific Help
System Time:
System Date:
[19:10:59]
[01/09/2009]
Total Memory:
Video Memory:
4095 MB
512 MB
Quick Boot
Network Boot
F12 Boot Menu
D2D Recovery
SATA Mode
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[AHCI]
F1 Help
ESC Exit
Select Item
Select Menu
F5/F6
Enter
This is the help for the
hour field. Valid range
is from 0 to 23.
INCREASE/REDUCE: F 5 / F 6
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed with 24hour format.
Format: HH:MM:SS
(hour:minute:second)
System Date
Sets the system date.
Format MM/DD/YYYY
(month/day/year)
Total Memory
Displays the total memory available.
N/A
Video Memory
Displays the available memory for Video.
N/A
Quick Boot
Allows startup to skip certain tests while booting,
decreasing the time needed to boot the system.
Option: Enabled or
Disabled
Network Boot
Enables, disables the system boot from LAN (remote
server).
Option: Enabled or
Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Enabled or Enabled
D2D Recovery
Enables, disables D2D Recovery function. The function
allows the user to create a hidden partition on hard disc
drive to store operation system and restore the system
to factory defaults.
Option: Enabled or
Disabled
SATA Mode
Control the mode in which the SATA controller should
operate.
Option: AHCI or IDE
Chapter 2
23
Advanced
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.
Information
Main
InsydeH20 Setup Utility
Security
Boot
Power
Exit
Advanced
Rev. 3.5
Item Specific Help
XBoot Configuration
XPeripheral Configuration
XIDE Configuration
XThermal Configuration
XVideo Configuration
XUSB Configuration
XChipset Configuration
XACPI Table/Features Control
Express Card
[Disabled]
XPCI Express Configuration
XASF Configuration
F1 Help
ESC Exit
Select Item
Select Menu
F5/F6
Enter
Configures Boot
Settings.
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
24
Description
Submenu Items
Boot Configuration
Enter the Boot Configuration menu.
•
Numlock
Peripheral
Configuration
Enter the Peripheral Configuration menu.
•
•
•
•
Serial Port A
Infrared Port
Azalia
Lan
IDE Configuration
Enter the IDE Configuration menu.
•
•
•
•
•
IDE Controller
HDC Configure as
AHCI Option ROM Support
SATA Port 0, 1, 4, 5 HotPlug
Channel 1 to 4 Master and Slave
Chapter 2
Parameter
Description
Submenu Items
Video
Configuration
Enter the Video Configuration menu.
•
•
•
•
•
•
•
•
•
•
Render Standby
IGD—Device2, Function1
IGD—Pre-allocat Memory
IGD—DVMT Size
Clock Chip Initialize
Enabled CK SSC
IGD—Boot Type
IGD—LCD Panel Type
IGD—TV
IGD—PAVP Mode
USB Configuration
Enter the USB Configuration menu.
•
•
•
•
•
USB Legacy
EHCI 1, 2
UHCI 1 ~ 5
Per-Port Control
USB Port 0~7
Chipset
Configuration
Enter the Chipset Configuration menu.
•
•
•
•
•
•
Port 80h Cycles
DMI Link ASPM Control
Automatic ASPM
PCI Latency Timer
VT-d
iTPM
ACPI Table/
Features Control
Enter the ACPI Table/Features Control
menu.
•
•
•
•
•
FACP—C2 Latency Value
FACP—C3 Latency Value
FACP—RTC S4 Wakeup
APIC—IO APIC Mode
HPET—HPET Support
• Base Address select
Express Card
•
N/A
PCI EXpress Root
Port 1 ~ 6
•
PCI Express Root Port 1
• VC1 Enable
• ASPM
Automatic ASPM
• URR
• FER
• NFER
• CER
• CTO
• SEFE
• SENFE
• SECE
• PME Interrupt
• PMI SCI
• Hot Plug SCI
•
ASF Configuration
Chapter 2
•
•
•
•
Mini WatchDog Timeout
BIOS Boot Timeout
OS Boot Timeout
Power-on wait time
25
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Information
Main
Advanced
InsydeH20 Setup Utility
Security
Power
Boot
Exit
Rev. 3.5
Item Specific Help
Supervisor Password Is:
User Password Is:
HDD Password Is:
Clear
Clear
Clear
Set Supervisor Password
Set User Password
Set SATA Port0 HDD Password
Password on Boot
[Disabled]
F1 Help
ESC Exit
Select Item
Select Menu
F5/F6
Enter
C h a n g e Va l u e s
Select
SubMenu
Install or Change the
password and the length
of password must be less
than eight words.
F9
F10
Setup Default
Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Supervisor Password Is
Shows the setting of the Supervisor password
Clear or Set
User Password Is
Shows the setting of the user password.
Clear or Set
HDD Password Is
Shows the setting of the hard disk password.
Clear or Set
Set Supervisor Password
Press Enter to set the supervisor password. When set,
this password protects the BIOS Setup Utility from
unauthorized access. The user can not either enter the
Setup menu nor change the value of parameters.
N/A
Set User Password
Press Enter to set the user password. When user
password is set, this password protects the BIOS Setup
Utility from unauthorized access. The user can enter
Setup menu only and does not have right to change the
value of parameters.
N/A
Set SATA Port0 HDD
Password
Enter HDD Password.
N/A
Password on Boot
Defines whether a password is required or not while the
events defined in this group happened. The following
sub-options are all requires the Supervisor password
for changes and should be grayed out if the user
password was used to enter setup.
Disabled or
Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
26
Chapter 2
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Supervisor Password box appears:
Set Supervisor Password
Enter New Password
Confirm New Password
2.
[
[
]
]
Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric
characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears:
Set Supervisor Password
Enter Current Password
Enter New Password
Confirm New Password
[
[
[
]
]
]
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
27
Changing a Password
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears.
Set Supervisor Password
Enter Current Password
Enter New Password
Confirm New Password
[
[
[
]
]
]
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
Setup Notice
Changes have been saved.
[Continue]
The password setting is complete after the user presses Enter.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
Setup Warning
Invalid Password.
[Continue]
If the new password and confirm new password strings do not match, the screen will display the following
message.
Setup Warning
Passwords do not match.
Re-enter password.
[Continue]
28
Chapter 2
Power
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.
Information
Main
InsydeH20 Setup Utility
Security
Boot
Power
Exit
Advanced
Rev. 3.5
Item Specific Help
XAdvanced CPU Control
XPlatform Power Management
XBreak Event
ACPI S3:
Wake on PME
Wake on Modem Ring
Quickly S4 Resume
Auto wake on S5
F1 Help
ESC Exit
These items control
various CPU parameters.
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
Select Item
Select Menu
F5/F6
Enter
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
Description
Submenu Items
Advanced CPU
Control
Enter the Advanced CPU Control menu.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
P-States (IST)
Boot performance mode
Thermal Mode
CMP Support
Use XD capability
VT Support
SMRR Support
C-States
Enhanced C-States
C-State Pop Up Mode
C-State Pop Down Mode
C4 Exit Timing Mode
Deep C4
Hard C4E
Enable C6
Platform Power
Management
Enter the Platform Power Management
menu.
•
PCI Clock Run
Chapter 2
29
Parameter
30
Description
Submenu Items
Break Event
Enter the Break Event menu.
•
•
•
•
•
•
Storage Break Event
PCIE Break Event
PCI Break Event
EHCI Break Event
UHCI Break Event
HDA Break Event
ACPI S3
Enable or Disable ACPI S1/S3 Sleep State.
N/A
Wake on PME
Disable or Enable wake up when the
system power is off and a PCI Power
Management Enable wake up event occurs.
N/A
Wake on Modem
Ring
Disable or Enable wake up when the
system power is off and a modem attached
to the serial port is ringing.
N/A
Quickly S4
Resume
Disable or Enable optional quick boot from
S4 Resume.
N/A
Auto wake on S5
Disable or Enable auto wake up by date
and time or at a fixed time everyday.
N/A
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Select Boot Devices to select specific devices to support boot.
Information
Main
Advanced
InsydeH20 Setup Utility
Security
Power
Boot
Exit
Rev. 3.5
Item Specific Help
Boot priority order:
1.
2.
3.
3.
4.
5.
6.
F1 Help
ESC Exit
Chapter 2
Use < > or < > to select
a device, then press
<F5> to move it down the
list, or <F6> to move
it up the list. Press
<Esc> to escape the menu
IDE0 : WDC WD5000BEVT-22ZAT0
IDE2 :
IDE1 : MATSHITADVD-RAM UJ880AS
USB FDD :
Network Boot : Atheros Boot Agent
USB HDD :
USB CDROM :
Select Item
Select Menu
F5/F6
Enter
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
31
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
Information
Main
Advanced
InsydeH20 Setup Utility
Security
Power
Boot
Exit
Rev. 3.5
Item Specific Help
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
ESC Exit
Select Item
Select Menu
Exit System Setup and
save your changes to
CMOS.
F5/F6
Enter
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
The table below describes the parameters in this screen.
Parameter
32
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding
Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
BIOS Flash Utilities
The BIOS flash memory update is required for the following conditions:
•
New versions of system programs
•
New features or options
•
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the flash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
33
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1.
Press F2 during boot to enter the Setup Menu.
2.
Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move
USB HDD to position 1.
Information
Main
Advanced
InsydeH20 Setup Utility
Security
Power
Boot
Exit
Rev. 3.5
Item Specific Help
Boot priority order:
1.
2.
3.
3.
4.
5.
6.
F1 Help
ESC Exit
3.
Use < > or < > to select
a device, then press
<F5> to move it down the
list, or <F6> to move
it up the list. Press
<Esc> to escape the menu
IDE0 : WDC WD5000BEVT-22ZAT0
IDE2 :
IDE1 : MATSHITADVD-RAM UJ880AS
USB FDD :
Network Boot : Atheros Boot Agent
USB HDD :
USB CDROM :
Select Item
Select Menu
F5/F6
Enter
C h a n g e Va l u e s
Select
SubMenu
F9
F10
Setup Default
Save and Exit
Execute the FLASH.BAT batch file to update BIOS.
The flash process begins as shown.
34
Chapter 2
4. In flash BIOS, the message Please do not remove AC Power Source displays.
NOTE: If the AC power is not connected, the following message displays.
Plug in the AC power to continue.
5.
Flash is complete when the message Flash programming complete displays.
Chapter 2
35
WinFlash Utility
Perform the following steps to use the WinFlash Utility:
36
1.
Double-click the WinFlash executable.
2.
Click OK to begin the update. A progress screen displays.
Chapter 2
Remove HDD/BIOS Password Utilities
This section provides you with details about removing HDD/BIOS password:
Remove HDD Password:
If you key in the wrong HDD password three times, an error is generated.
To reset the HDD password, perform the following steps:
1.
After the error is displayed, select the Enter Unlock Password option on the screen.
2.
An Encode key is generated for unlocking utilities. Note down this key.
3.
Execute the UnlockHD.EXE file to create the unlock code in DOS Mode using the format UnlockHD
[Encode code] with the code noted in the previous step, as follows:
UnlockHD 76943488
4.
The command generates a password which can be used for unlocking the HDD.
Password : 46548274
5.
Key in the password from the previous step to unlock the HDD as shown.
Chapter 2
37
Removing BIOS Passwords:
To clear the User or Supervisor passwords, open the RAM door and use a metal instrument to short the J1
jumper.
Cleaning BIOS Passwords
To clean the User or Supervisor passwords, perform the following steps:
1.
From a DOS prompt, execute clnpwd.exe
2.
Press 1 or 2 to clean the desired password shown on the screen.
The onscreen message determines whether the function is successful or not.
38
Chapter 2
Using Boot Sequence Selector
The Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot
Sequence Selector, perform the following steps:
1.
Enter into DOS.
2.
Execute BS.exe to display the usage screen.
3.
Select the desired boot sequence by entering the corresponding sequence. For example, enter BS2 to
change the boot sequence to HDD | CD ROM | LAN | Floppy.
Chapter 2
39
Using DMITools
The DMI (Desktop Management Interface) Tool copies BIOS information to EEPROM to be used in the DMI
pool for hardware management.
When the BIOS displays Verifying DMI pool data it is checking that the table correlates with the hardware
before sending to the operating system (Windows, etc.).
To update the DMI Pool, perform the following steps:
1.
Boot into DOS.
2.
Execute dmitools. The following messages report to screen to confirm completion:
•
dmitools /r ==> Read dmi string from bios
•
dmitools /wm xxxx ==> Write manufacturer name to eeprom (max. 16 characters)
•
dmitools /wp xxxx ==> Write product name to eeprom (max. 16 characters)
•
dmitools /ws xxxx ==> Write serial number to eeprom (max. 22 characters)
•
dmitools /wu xxxx ==> Write uuid to eeprom
•
dmitools /wa xxxx ==> Write asset tag to eeprom (max. 32 characters)
The following examples show the commands and the corresponding output information.
Read DMI Information from Memory
Input:
dmitools /r
Output:
Manufacturer (Type1, Offset04h): Acer
Product Name (Type1, Offset05h): TravelMate xxxxx
Serial Number (Type1, Offset07h): 01234567890123456789
UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
Asset Tag (Type3, Offset04h): Acet Asstag
Write Product Name to EEPROM
Input:
dmitools /wp Acer
Write Serial Number to EEPROM
Input:
dmitools /ws 01234567890123456789
4 ). Write UUID to EEPROM ( Create UUID from Intel WFM20.pdf )
Input:
dmitools /wu
5). Write Asset Tag to EEPROM
Input:
dmitools /wa Acet Asstag
NOTE: When using any of the Write options, restart the system to make the new DMI data effective.
40
Chapter 2
Using the LAN MAC EEPROM Utility
You can use the MAC.BAT utility to write the MAC.CFG file to the EEPROM under DOS mode.
1.
2.
Use a text editor (for example: Notepad) to open the MAC.CFG file. You can see the MAC.CFG contents
as below:
WriteData = ‘001122334455'
MAC value
StartAddr=7A
MAC address
WriteLeng=6
MAC value length
KeepByte=0
don’t care
In DOS mode, run the MAC.BAT file to write MAC values to eeprom.
Chapter 2
41
42
Chapter 2
Chapter 3
Machine Disassembly and Replacement
IMPORTANT: The outside housing and color may vary from the mass produced model.
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
•
Wrist grounding strap and conductive mat for preventing electrostatic discharge
•
Flat screwdriver
•
Philips screwdriver
•
Plastic flat screwdriver
•
Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3
43
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.
4. Remove the battery pack.
Disassembly Process
IMPORTANT: The LCD Module cannot be disassembled outside of factory conditions. If any part of the LCD
Module is faulty, such as the camera, antenna or LCD panel, the whole module must be replaced.
The disassembly process is divided into the following stages:
•
External module disassembly
Main unit disassembly
•
LCD module disassembly
•
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the mainboard, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List
Screw
44
Quantity
Part Number
SCREW M2.48D 4.0L K 5.5D 0.8T ZKNL
1
86.N2802.001
SCREW M2.48D 6.0L K 5.5D 0.8T ZKNL
6
86.N2802.002
SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL
30
86.N2802.003
SCREW M1.98D 3.0L K 4.6D 0.8T ZKNL
4
86.N2802.004
SCREW M M 3.0D 3.0L K 4.9D NI +
4
86.N2802.005
SCREW M M 2.5D 3.2L K 6D NI +
17
86.N2802.006
Chapter 3
External Module Disassembly Process
IMPORTANT: The outside housing and color may vary from the mass produced model.
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation of the external module disassembly sequence and
instructs you on the components that need to be removed during servicing. For example, if you want to remove
the keyboard, you must first remove the switch board.
Turn off system
and peripherals
power
Disconnect power
and signal cables
from system
Remove
Battery
Remove
Dummy Card
Remove
Lower Covers
Remove
ODD
Remove
DIMMs
Remove
WLAN
Remove
HDD
Screw List
Step
Screw
Quantity
Part No.
Lower Covers
M2.5*8
3
86.N2802.003
ODD Module
M2.5*8
1
86.N2802.003
WLAN Module
M2*3
2
86.N2802.006
HDD Carrier
M3*3
4
86.N2802.005
Chapter 3
45
Removing the Battery Pack
1. Turn computer over. Slide the battery lock in the direction shown.
2. Slide and hold the battery release latch to the release position (1), then lift out the battery pack from the main
unit (2).
2
1
46
Chapter 3
Removing the SD Dummy Card
1. Push the SD dummy card all the way in to eject it.
2. Pull it out from the slot.
Chapter 3
47
Removing the Lower Covers
1. See “Removing the Battery Pack” on page 46.
2. Remove the three screws securing the Memory and HDD Covers.
HDD
Cover
Memory
Cover
Step
Lower Covers
Size
M2.5*8
Quantity
Screw Type
3
3. Remove the HDD cover as shown.
4. Carefully open the Memory Cover.
48
Chapter 3
Removing the Optical Drive Module
1. See “Removing the Battery Pack” on page 46.
2. Remove the screw securing the ODD module.
Step
ODD Module
Size
M2.5*8
Quantity
Screw Type
1
3. Insert a suitable tool into the access slot in the battery bay as shown. Gently lever the ODD module out of the
chassis.
4. Pull the optical drive module out from the chassis.
Chapter 3
49
5. Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive
module.
Step
ODD Bracket
Size
M2*3
Quantity
Screw Type
2
6. Remove the ODD bezel by rotating the top edge downward and pulling it clear of the module.
50
Chapter 3
Removing the DIMM Modules
1. See “Removing the Lower Covers” on page 48.
2. Push out the release latches on both sides of the DIMM socket to release the DIMM module.
3. Remove the DIMM module.
4. Repeat steps for the second DIMM module if present.
Chapter 3
51
Removing the WLAN Module
1. See “Removing the Lower Covers” on page 48.
2. Remove the adhesive tape securing the Antenna cables in place.
3. Disconnect the antenna cables from the WLAN Board.
NOTE: Cable placement is Black to the MAIN terminal (upper) and White to the AUX terminal (lower).
52
Chapter 3
4. Move the antenna away and remove the two screws to release the WLAN Board.
Step
WLAN Module
Size
M2*3
Quantity
Screw Type
2
5. Detach the WLAN Board from the WLAN socket.
NOTE: When reattaching the antennas, ensure the cables are tucked into the chassis to prevent damage.
Chapter 3
53
Removing the Hard Disk Drive Module
1. See “Removing the Lower Covers” on page 48.
2. Using the pull-tab, slide the HDD Module in the direction of the arrow to disconnect the interface.
3. Lift the HDD Module clear of the HDD bay.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
54
Chapter 3
4. Remove the four screws (two each side) securing the hard disk to the carrier.
Step
HDD Carrier
Size
M3*3
Quantity
Screw Type
4
5. Remove the HDD from the carrier.
Chapter 3
55
Main Unit Disassembly Process
Main Unit Disassembly Flowchart
Remove External
Modules before
proceeding
Remove
Switch Cover
Remove
Keyboard
Remove
LCD Module
Remove
Upper Cover
Upper
Cover
Remove
Power Board
Remove
Left Speaker
Module
Lower
Cover
Remove
Right Speaker
Module
Remove
TouchPad
Bracket
Remove
Mainboard
Remove
RTC Battery
Remove
Thermal Module
Remove
CPU Fan
Remove
CPU
Screw List
Step
56
Screw
Quantity
Part No.
LCD Module
M2.5*8
2
86.N2802.003
LCD Module
M2.5*8
4
86.N2802.003
Upper Cover
M2.5*8
11
86.N2802.003
Upper Cover
M2.5*8
9
86.N2802.003
Power Board
M2*3
2
86.N2802.006
Left Speaker Module
M2*3
1
86.N2802.006
Right Speaker Module
M2*3
1
86.N2802.006
TouchPad Bracket
M2*3
2
86.N2802.006
Mainboard
M2.5*4
1
86.N2802.001
Thermal Module
M1.98*3.0
4
86.N2802.004
CPU Fan
M2*3
3
86.N2802.006
Chapter 3
Removing the Switch Cover
CAUTION: Using metal tools to remove the Switch Cover may cause damage to the outer casing. The use of
plastic tools or fingers is recommended to remove the Switch Cover.
1. See “Removing the Battery Pack” on page 46.
2. Turn the computer over. Press down the / and * keys on the right side of the Keyboard to expose the cutout.
Insert a suitable plastic tool (or finger) and pry the Switch Cover upward, away from the Upper Cover.
3. Work along the Switch Cover toward the left hinge, gently prying up the cover as shown.
4. Lift the Switch Cover clear of the computer.
Chapter 3
57
Removing the Keyboard
1. See “Removing the Switch Cover” on page 57.
2. Pry up the centre of the Keyboard and rotate it upward away from the Upper Cover.
3. Turn the keyboard over on to the TouchPad area to expose the FFC connector.
4. Open the locking latch and disconnect the FFC from the mainboard.
5. Lift the keyboard clear of the Upper Cover.
58
Chapter 3
Removing the LCD Module
1. See “Removing the Keyboard” on page 58.
2. Turn the computer over. Remove the two securing screws from the bottom of the chassis.
Step
LCD Module
Size
M2.5*8
Quantity
Screw Type
2
3. Remove the Antenna Cables from the cable channel as shown. Ensure that the cables are free from all cable
clips.
Chapter 3
59
4. Stand the computer on the LCD Panel and pull the Antenna cables completely through the chassis.
5. Disconnect the LCD cable from the Mainboard and remove the cable from the cable channel.
6. Remove the white Antenna cable from the cable channel. Ensure that the cable is completely free of the
retaining clips all the way to the hinge well.
60
Chapter 3
7. Remove the adhesive tape securing the Antenna cable to the Upper Cover.
8. Remove the black Antenna cable from the cable channel as shown. Ensure that the cable is completely free of
the retaining clips all the way to the hinge well.
9. Open the LCD Panel to the full extent to expose the Hinge Covers.
10. Press the left side Hinge Cover inward, as shown, and lift to remove the cover from the chassis.
11. Repeat the process for the right side Hinge Cover.
Chapter 3
61
12. Remove the four securing screws (two each side) from the LCD module.
Step
LCD Module
Size
M2.5*8
Quantity
Screw Type
4
13. Remove the left and right screw covers from on top of the hinges
14. Lift the LCD Module clear of the Upper Cover.
62
Chapter 3
Removing the Upper Cover
1. See “Removing the LCD Module” on page 59.
2. Turn the computer over. Remove the eleven screws on the bottom panel.
Step
Upper Cover
Size
M2.5*8
Quantity
Screw Type
11
3. Turn the computer over. Remove the three screw caps at the rear of the Upper Cover as shown.
Chapter 3
63
4. Disconnect the following four cables from the Mainboard.
A
B
C
D
64
Chapter 3
5. Disconnect A as shown.
6. Disconnect C as shown.
7. Release the locking latch on B and remove the FFC cable as shown.
8. Release the locking latch on D and remove the FFC cable as shown.
NOTE: Avoid pulling on cables directly to prevent damage to the connectors.
NOTE: Use the pull-tabs on FFCs whenever available to prevent damage.
Chapter 3
65
9. Remove the nine screws on the top panel.
Step
Upper Cover
Size
M2.5*8
Quantity
Screw Type
9
10. Starting at the rear left side of the cover, pry apart the Upper and Lower Covers as shown. Work along the back
edge of the casing to the right as shown, then lift the Upper Cover clear of the Lower Cover.
66
Chapter 3
Removing the Power Board
1. See “Removing the Upper Cover” on page 63.
2. Locate the Power Board on the Upper Cover as shown.
3. Remove the two screws securing the Power Board to the Upper Cover.
Step
Power Board
Size
M2*3
Quantity
Screw Type
2
4. Lift the Power Board clear of the Upper Cover as shown.
Chapter 3
67
Removing the Left Speaker Module
1. See “Removing the Upper Cover” on page 63.
2. Locate the Left Speaker Module on the Upper Cover as shown.
3. Remove the adhesive tape from the Speaker cable.
4. Remove the Speaker cable from the cable channel. Ensure that the cable is free from all cable clips.
68
Chapter 3
5. Remove the single securing screw from the Left Speaker Module.
Step
Left Speaker
Module
Size
M2*3
Quantity
Screw Type
1
6. Lift the Speaker clear of the Upper Cover, left side first as shown.
Chapter 3
69
Removing the Right Speaker Module
1. See “Removing the Upper Cover” on page 63.
2. Locate the Right Speaker Module on the Upper Cover as shown.
3. Turn the Upper Cover over and remove the Right Speaker Module cable from the cable channel. Ensure that
the cable is free from all cable clips.
4. Turn the Upper Cover over and pass the cable through the cover as shown.
70
Chapter 3
5. Remove the single securing screw from the Right Speaker Module.
Step
Right Speaker
Module
Size
M2*3
Quantity
Screw Type
1
6. Lift the Speaker clear of the Upper Cover, right side first as shown.
Chapter 3
71
Removing the TouchPad Bracket
IMPORTANT: The TouchPad Board cannot be removed individually. To replace the TouchPad Board, replace the
entire Upper Cover.
1. See “Removing the Upper Cover” on page 63.
2. Lift the FFC to detach the adhesive securing the cable to the Upper Cover.
3. Release the FFC locking latch and disconnect the TouchPad FFC from the cover.
72
Chapter 3
4. Remove the two screws from TouchPad bracket.
Step
TouchPad Bracket
Size
M2*3
Quantity
Screw Type
2
5. Lift the rear edge of the TouchPad bracket first to clear the securing clips and remove it as shown.
Chapter 3
73
Removing the Mainboard
1. See “Removing the Upper Cover” on page 63.
2. Remove the single securing screw from the Mainboard.
Step
Mainboard
Size
M2.5*4
Quantity
Screw Type
1
3. Lift the mainboard from the chassis, right edge first, and place it on a clean, dust-free surface.
74
Chapter 3
Removing the RTC Battery
IMPORTANT:Follow local regulations for disposal of all batteries.
The RTC Battery is soldered to the Mainboard. To replace the battery, solder the new battery to the
connections shown.
Chapter 3
75
Removing the Thermal Module
1. See “Removing the Lower Covers” on page 48.
2. Turn the Mainboard over to access the Thermal Module.
3. Remove the four securing screws (in reverse numerical order from screw 4 to screw 1) from the Thermal
Module.
Step
Thermal Module
76
Size
4
2
1
3
Quantity
Screw Type
4
Chapter 3
4. Using both hands, lift the Thermal Module clear of the Mainboard.
Chapter 3
77
Removing the CPU Fan
1. See “Removing the Thermal Module” on page 76.
2. Disconnect the Fan cable from the Mainboard as shown.
3. Remove the three securing screws from the Fan Module.
Step
CPU Fan
78
Size
M2*3
Quantity
Screw Type
3
Chapter 3
4. Lift the CPU Fan clear of the Mainboard as shown.
Chapter 3
79
Removing the CPU
IMPORTANT: The pins on the underside of the CPU are very delicate. If they are damaged, the CPU may
malfunction. Place the CPU on a clean, dry surface when it is not installed.
1. See “Removing the Thermal Module” on page 76.
2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° counter-clockwise as shown.
3. Lift the CPU clear of the socket as shown.
80
Chapter 3
LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Remove LCD
Panel from Main
Unit before
proceeding
Remove
LCD Bezel
Remove
LCD Brackets
Remove
LCD Panel
Remove
Camera Module
Remove
LCD FPC Cable
Remove
Antennas
Screw List
Step
Screw
Quantity
Part No.
LCD Bezel
M2.5*6
4
86.N2802.002
LCD Panel
M2.5*6
2
86.N2802.002
LCD Brackets
M2*3
6
86.N2802.006
Chapter 3
81
Removing the LCD Bezel
1. See “Removing the LCD Module” on page 59.
2. Remove the two upper and two lower bezel screw caps and screws.
Step
LCD Bezel
3.
82
Size
M2.5*6
Quantity
Screw Type
4
Starting from the bottom edge of the bezel, pry the bezel upwards and away from the panel. Work along the
right side toward the top of the bezel, prying the covers apart. Continue along the top edge and down the left
side to remove the bezel.
NOTE: If necessary, use a pry to lift up the outside edges of the bezel.
Chapter 3
Removing the Camera Module
1. See “Removing the LCD Bezel” on page 82.
2. Locate the Camera Module at the top of the LCD Module and disconnect the camera cable.
3. Remove the Camera from the module.
Chapter 3
83
Removing the LCD Panel
1. See “Removing the Camera Module” on page 83.
2. Remove the two securing screws from the LCD Panel.
Step
LCD Panel
Size
M2.5*6
Quantity
Screw Type
2
3. Remove the adhesive strip holding the cables in place.
4. Remove the Camera cable cluster from the LCD Module as shown.
84
Chapter 3
5. Lift the LCD Panel clear of the module.
Chapter 3
85
Removing the LCD Brackets and FPC Cable
1. See “Removing the LCD Panel” on page 84.
2. Remove the six securing screws (three on each side) from the LCD Panel brackets.
Step
LCD Brackets
Size
M2*3
Quantity
Screw Type
6
3. Remove the LCD brackets by pulling away from the LCD Panel.
86
Chapter 3
4. Turn the LCD panel over to expose the rear. Lift the adhesive protector and disconnect the cable from the LCD
Panel.
5. Lift the cable as shown to disengage the adhesive strip securing it in place.
6. Lift the FPC cable to disengage the remaining adhesive and remove the cable from the panel.
Chapter 3
87
Removing the Antennas
1. See “Removing the LCD Panel” on page 84.
2. Remove the adhesive strips holding the left antenna cable in place. Ensure the cable is free from obstructions.
3. Remove the cable from the cable channel. Ensure that the cable is free from all cable clips and adhesive strips.
4. Remove the adhesive tape securing the left Antenna to the LCD Module.
88
Chapter 3
5. Lift the left Antenna clear of the cover.
6. Remove the adhesive strips holding the right antenna cable in place. Ensure the cable is free from
obstructions.
7. Remove the cable from the cable channel. Ensure that the cable is free from all cable clips and adhesive strips.
Chapter 3
89
8. Remove the adhesive tape securing the right Antenna to the LCD Module.
9. Lift the right Antenna clear of the cover.
90
Chapter 3
LCD Module Reassembly Procedure
Replacing the Antennas
1. Replace the right Antenna as shown. Ensure that the locating pins on the Antenna are correctly seated.
Locating Pin
Locating Pin
2. Replace the adhesive strip to secure the Antenna
in place.
3. Run the cable down the side of the LCD Module
using all available clips and adhesive.
4. Run the cable along the cable channel as shown, using all available cable clips.
Chapter 3
91
5. Replace the left Antenna as shown. Ensure that the locating pins on the Antenna are correctly seated.
Locating Pin
6. Replace the adhesive strip to secure the Antenna
in place.
Locating Pin
7. Run the cable down the side of the LCD Module
using all available clips and adhesive.
8. Run the cable along the cable channel as shown, using all available cable clips and adhesive.
92
Chapter 3
9. The Antennas and cables appear as shown when correctly installed.
Chapter 3
93
Replacing the LCD Panel
1. Connect the LCD cable to the panel connector as
shown.
2. Press down the adhesive strip to secure the cable
in place.
3. Run the cable along the back of the panel and
press down as indicated to secure the cable in
place.
4. Run the cable across the back of the panel as
shown and press down as indicated to secure the
cable in place.
IMPORTANT: Ensure that the LCD cable runs between the green callouts to avoid trapping when the panel is
replaced in the LCD Module.
94
Chapter 3
5. Align the LCD brackets with the screw holes on the panel. Replace the six screws (three on each side) in the
brackets as shown.
6. Place the LCD Panel in the LCD Module, top edge first, and secure the LCD cable with adhesive tape.
IMPORTANT: Ensure that the LCD power cable passes through the hinge well and is not trapped under the
panel.
Chapter 3
95
7. Replace the Camera cable cluster in the LCD
Module.
8. Secure the LCD module with the two securing
screws.
Replacing the Camera Module
1. Place the camera in the LCD Module.
96
2. Connect the cable to the camera module.
Chapter 3
Replacing the LCD Bezel
1. Replace the bezel and press down until there are no gaps between the bezel and the LCD Module.
IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped by the bezel.
Chapter 3
97
2. Replace the four screws and screw caps provided.
98
Chapter 3
Main Module Reassembly Procedure
Replacing the CPU
IMPORTANT: The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU
socket.
1. Place the CPU into the CPU socket as shown, taking note of the Pin1 locator.
Socket
Pin1 Locator
CPU
Pin1 Locator
2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° clockwise to secure the CPU in place.
Chapter 3
99
Replacing the CPU Fan
1. Align the screw holes on the CPU Fan and
Mainboard and replace the Fan.
2. Replace the three screws to secure the Fan to the
Mainboard.
3. Connect the Fan power cable to the Mainboard connector.
Replacing the Thermal Module
IMPORTANT: Apply a suitable thermal grease and ensure all heat pads are in place before replacing the Thermal
Module.
The following thermal grease types are approved for use:
•
•
•
Silmore GP50
Honeywell
Jet Motor 7762
The following thermal pads are approved for use:
•
Eapus XR-PE
1. Remove all traces of thermal grease from the CPU using a lint-free cloth or cotton swab and Isopropyl
Alcohol, Acetone, or other approved cleaning agent.
2. Apply a small amount of thermal grease to the centre of the CPU—there is no need to spread the grease
manually, the force used during the installation of the Thermal Module is sufficient.
100
Chapter 3
3. Align the screw holes on the Thermal Module and
Mainboard then replace the module. Keep the
module as level as possible to spread the thermal
grease evenly.
4. Replace the four securing screws (in numerical
order from screw 1 to screw 4) to secure the
Thermal Module in place.
4
2
1
3
Replacing the Mainboard
1. Ensure that the Mainboard is face up (the CPU is not visible). Place the Mainboard in the chassis, left edge
first (1), then rotate it downward into position (2).
(2)
(1)
NOTE: Ensure the I/O ports are positioned correctly through the casing.
2. Replace the single securing screw in the mainboard.
Chapter 3
101
Replacing the TouchPad Bracket
1. Replace the TouchPad bracket top edge first to
engage the securing clips.
2. Press the bracket down to engage the securing
clips.
3. Replace the two screws to secure the TouchPad Bracket to the Upper Cover.
4. Replace the TouchPad FFC and close the locking latch on the connector.
102
Chapter 3
5. Replace the FFC and press down as indicated to secure it to the Upper Cover.
Chapter 3
103
Replacing the Right Speaker Module
1.
Place the module left side first on the Upper Cover 2. Replace the single screw to secure the module in
as shown. Ensure that the left side of the module is
place.
seated correctly in the securing clip.
3. Pass the cable through the Upper Cover as shown. 4. Turn the Upper Cover over and run the cable along
the cable channel using all available cable clips.
5. The cable runs as shown when correctly installed.
104
Chapter 3
Replacing the Left Speaker Module
1.
Place the module right side first on the Upper
Cover as shown. Ensure that the right side of the
module is seated correctly in the securing clip.
2. Replace the single screw to secure the module in
place.
3. Run the cable along the cable channel using all available cable clips.
4. Secure the cable in place with adhesive tape.
Chapter 3
5. The cable runs as shown when correctly installed.
105
Replacing the Power Board
1.
Slide the Power Board in to the Upper Cover front edge first to engage the securing clip.
2. Press the board down to locate the securing pin.
3. Replace the two screws to secure the board to the
Upper Cover.
Replacing the Upper Cover
1.
106
Place the Upper Cover on the Lower Cover as shown.
Chapter 3
2. Press down around the edges to secure it in place.
3. Replace the nine screws in the Upper Cover as shown.
Chapter 3
107
4. Replace the three screw caps as shown.
5. Connect the following cables to the Mainboard.
A
B
C
D
108
Chapter 3
6. Connect A as shown.
7. Connect C as shown.
8. Connect B and close the locking latch to secure the cable in place.
9. Connect D and close the locking latch to secure the cable in place.
Chapter 3
109
10. Turn the computer over and replace the eleven screws as shown.
Replacing the LCD Module
1. Align the screw holes on the LCD Module and
Upper Cover and replace the LCD Module.
2. The left and right screw covers are shaped
differently. Ensure that the correct cover is used.
Left Screw
Cover
Right Screw
Cover
3. Replace the left screw cover as shown. Ensure that the securing tab on the rear of the cover is seated
correctly in the Upper Cover.
110
Chapter 3
4. Replace the right screw cover as shown. Ensure that the securing tab on the rear of the cover is seated
correctly in the Upper Cover.
5. Replace the four screws securing the LCD Module to the Upper Cover.
6. Ensure that the Hinge Covers are replaced
7. Align the left Hinge Cover as shown and press
correctly. Identify the rear edge of the covers by the
down to replace the cover.
two securing clips.
Rear Securing
Clips
8. Repeat the process for the right side Hinge Cover.
Chapter 3
111
9. Run the black Antenna cable along the cable
channel as shown using all available retaining
clips.
10. Replace the adhesive strip to secure the cable in
place.
11. Run the white Antenna cable along the cable channel as shown using all available retaining clips.
12. Run the LCD cable along the cable channel using
all available cable clips.
112
13. Connect the LCD cable to the Mainboard as
shown.
Chapter 3
14. Stand the computer on the LCD Panel and pass the Antenna cables through the chassis.
15. The Upper Cover appears as shown when the Antenna and LCD cables are correctly installed.
16. Turn the computer over. Run the Antenna cables along the cable channel as shown, using all available
cable clips.
Chapter 3
113
17. Replace the two screws securing the LCD Module to the Lower Cover.
114
Chapter 3
Replacing the Keyboard
1. Connect the Keyboard FFC to the Mainboard and close the locking latch to secure the cable in place.
2. Turn the Keyboard over and insert it front edge first 3. Press down as indicated to secure the Keyboard in
into the chassis.
place.
NOTE: Ensure that the six locating tabs are
correctly seated.
Chapter 3
115
Replacing the Switch Cover
1. Place the Switch Cover left side first on to the Upper Cover.
2. Press down as indicated to snap the Switch Cover into place.
Replacing the Hard Disk Drive Module
1. Place the HDD in the HDD carrier.
116
2. Replace the four screws (two each side) to secure
the carrier.
Chapter 3
3. Insert the HDD, as indicated and lower it into
place.
Chapter 3
4. Slide the HDD in the direction of the arrow to
connect the interface.
117
Replacing the WLAN Module
1. Insert the WLAN Module into the WLAN socket.
2. Replace the two screws to secure the module.
3. Connect the two Antenna cables to the module.
NOTE: The black cable connects to the upper
terminal (MAIN) and the white cable to the
lower terminal (MAIN).
4. After connecting the cables to the terminals,
secure the cables in place with adhesive tape to
avoid trapping.
Replacing the DIMM Modules
1. Insert the DIMM Module in place.
2. Press down to lock the DIMM module in place.
3. Repeat steps for the second DIMM module if present.
118
Chapter 3
Replacing the ODD Module
1. Press the bezel into the tray, bottom edge first, to
secure it to the ODD Module.
2. Secure the ODD bracket with the two screws.
3. Push the ODD Module into the ODD bay until it is
flush with the casing.
4. Replace the single screw to secure the Module.
Replacing the Lower Covers
1. Replace the Memory Cover as shown.
2. Replace the HDD Cover as shown.
IMPORTANT: Press down around the perimeter of the covers to ensure that the all the securing tabs are
correctly located in the casing.
Chapter 3
119
3. Replace the three screws to secure the covers in place.
Memory
Cover
HDD
Cover
Replacing the SD Dummy Card
1. Insert the SD Dummy Card into the slot as shown.
120
2. Push until the card clicks into place and is flush with
the casing.
Chapter 3
Replacing the Battery
1. Slide and hold the battery release latch to the
release position (1), insert the battery pack and
press down (2).
2. Slide the battery lock in the direction shown to
secure the battery in place.
2
1
Chapter 3
121
122
Chapter 3
Chapter 4
Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power On Issue
Page 124
No Display Issue
Page 125
LCD Failure
Page 127
Internal Keyboard Failure
Page 127
TouchPad Failure
Page 128
Internal Speaker Failure
Page 128
ODD Failure
Page 131
WLAN Failure
Page 134
Thermal Unit Failure
Page 134
Other Functions Failure
Page 135
Intermittent Failures
Page 136
Undermined Failures
Page 136
4.
If the Issue is still not resolved, see “Online Support Information” on page 185.
Chapter 4
123
Power On Issue
If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Computer Shutsdown Intermittently
If the system powers off at intervals, perform the following actions one at a time to correct the problem.
124
1.
Check the power cable is properly connected to the computer and the electrical outlet.
2.
Remove any extension cables between the computer and the outlet.
3.
Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly
into a known good electrical outlet.
4.
Disconnect the power and open the casing to check the Thermal Unit (see “Thermal Unit Failure” on page
134) and fan airways are free of obstructions.
5.
Remove all external and non-essential hardware connected to the computer that are not necessary to
boot the computer to the failure point.
6.
Remove any recently installed software.
7.
If the Issue is still not resolved, see “Online Support Information” on page 185.
Chapter 4
No Display Issue
If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
No POST or Video
If the POST or video doesn’t display, perform the following actions one at a time to correct the problem.
1.
Make sure that the internal display is selected. On this notebook model, switching between the internal
display and the external display is done by pressing Fn+F5. Reference Product pages for specific model
procedures.
2.
Make sure the computer has power by checking at least one of the following occurs:
•
Fans start up
•
Status LEDs light up
If there is no power, see “Power On Issue” on page 124.
3.
Drain any stored power by removing the power cable and battery and holding down the power button for
10 seconds. Reconnect the power and reboot the computer.
4.
Connect an external monitor to the computer and switch between the internal display and the external
display is by pressing Fn+F5 (on this model).
If the POST or video appears on the external display, see “LCD Failure” on page 127.
5.
Disconnect power and all external devices including port replicators or docking stations. Remove any
memory cards and CD/DVD discs. Restart the computer.
If the computer boots correctly, add the devices one by one until the failure point is discovered.
6.
Reseat the memory modules.
7.
Remove the drives (see “Disassembly Process” on page 44).
8.
If the Issue is still not resolved, see “Online Support Information” on page 185.
Chapter 4
125
Abnormal Video Display
If video displays abnormally, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and
should be replaced. See “Disassembly Process” on page 44.
3.
If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD
is faulty and should be replaced. See “Disassembly Process” on page 44.
4.
Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings.
NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness.
If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See
“Disassembly Process” on page 44.
5.
Check the display resolution is correctly configured:
a.
Minimize or close all Windows.
b.
If display size is only abnormal in an application, check the view settings and control/mouse wheel
zoom feature in the application.
c.
If desktop display resolution is not normal, right-click on the desktop and select
Personalize´ Display Settings.
d.
Click and drag the Resolution slider to the desired resolution.
e.
Click Apply and check the display. Readjust if necessary.
6.
Roll back the video driver to the previous version if updated.
7.
Remove and reinstall the video driver.
8.
Check the Device Manager to determine that:
9.
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
If the Issue is still not resolved, see “Online Support Information” on page 185.
10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts.
11. If the Issue is still not resolved, see “Online Support Information” on page 185.
Random Loss of BIOS Settings
If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a
time to correct the problem.
1.
If the computer is more than one year old, replace the CMOS battery.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power
and data cables between devices.
If the BIOS settings are still lost, replace the cables.
126
4.
If HDD information is missing from the BIOS, the drive may be defective and should be replaced.
5.
Replace the Motherboard.
6.
If the Issue is still not resolved, see “Online Support Information” on page 185.
Chapter 4
LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
Built-In Keyboard Failure
If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
Chapter 4
127
TouchPad Failure
If the TouchPad doesn’t work, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Internal Speaker Failure
If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
128
Chapter 4
Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check
the Device Manager to determine that:
•
The device is properly installed.
•
There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
3.
Roll back the audio driver to the previous version, if updated recently.
4.
Remove and reinstall the audio driver.
5.
Ensure that all volume controls are set mid range:
a.
Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.
b.
Click Mixer to verify that other audio applications are set to 50 and not muted.
6.
Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected
as the default audio device (green check mark).
NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices
(clear by default).
7.
Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure
the speakers.
8.
Remove and recently installed hardware or software.
9.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
10. Reinstall the Operating System.
11. If the Issue is still not resolved, see “Online Support Information” on page 185.
Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to
correct the problem.
1.
Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´
Sound and select the Recording tab.
2.
Right-click on the Recording tab and select Show Disabled Devices (clear by default).
3.
The microphone appears on the Recording tab.
4.
Right-click on the microphone and select Enable.
5.
Select the microphone then click Properties. Select the Levels tab.
6.
Increase the volume to the maximum setting and click OK.
7.
Test the microphone hardware:
8.
a.
Select the microphone and click Configure.
b.
Select Set up microphone.
c.
Select the microphone type from the list and click Next.
d.
Follow the onscreen prompts to complete the test.
If the Issue is still not resolved, see “Online Support Information” on page 185.
Chapter 4
129
HDD Not Operating Correctly
If the HDD does not operate correctly, perform the following actions one at a time to correct the problem.
1.
Disconnect all external devices.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
Run the Windows Vista Startup Repair Utility:
a.
insert the Windows Vista Operating System DVD in the ODD and restart the computer.
b.
When prompted, press any key to start to the operating system DVD.
c.
The Install Windows screen displays. Click Next.
d.
Select Repair your computer.
e.
The System Recovery Options screen displays. Click Next.
f.
Select the appropriate operating system, and click Next.
NOTE: Click Load Drivers if controller drives are required.
g.
Select Startup Repair.
h.
Startup Repair attempts to locate and resolve issues with the computer.
i.
When complete, click Finish.
If an issue is discovered, follow the onscreen information to resolve the problem.
4.
Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support.
5.
Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that
CD/DVD drive is set as the first boot device on the Boot menu.
6.
Ensure all cables and jumpers on the HDD and ODD are set correctly.
7.
Remove any recently added hardware and associated software.
8.
Run the Windows Disk Defragmenter. For more information see Windows Help and Support.
9.
Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see
Windows Help and Support.
10. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
11. Replace the HDD. See “Disassembly Process” on page 44.
130
Chapter 4
ODD Failure
If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
ODD Not Operating Correctly
If the ODD exhibits any of the following symptoms it may be faulty:
•
Audio CDs do not play when loaded
•
DVDs do not play when loaded
•
Blank discs do not burn correctly
•
DVD or CD play breaks up or jumps
•
Optical drive not found or not active:
•
Not shown in My Computer or the BIOS setup
•
LED does not flash when the computer starts up
•
The tray does not eject
•
Access failure screen displays
•
The ODD is noisy
Perform the following general solutions one at a time to correct the problem.
1.
Reboot the computer and retry the operation.
2.
Try an alternate disc.
3.
Navigate to Start´ Computer. Check that the ODD device is displayed in the Devices with Removable
Storage panel.
4.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
Chapter 4
131
a.
Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device
and click Enable.
b.
Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and
click Enable.
c.
Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If
a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
d.
Check that there are no yellow exclamation marks against the items in DVD/CD-ROM drives. If a
device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
e.
If the exclamation marker is not removed from the item in the lists, try removing any recently installed
software and retrying the operation.
Discs Do Not Play
If discs do not play when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Check that the disc is correctly seated in the drive tray and that the label on the disc is visible.
2.
Check that the media is clean and scratch free.
3.
Try an alternate disc in the drive.
4.
Ensure that AutoPlay is enabled:
5.
a.
Navigate to Start´ Control Panel´ Hardware and Sound´ AutoPlay.
b.
Select Use AutoPlay for all media and devices.
c.
In the Audio CD and DVD Movie fields, select the desired player from the drop down menu.
Check that the Regional Code is correct for the selected media:
IMPORTANT:Region can only be changed a limited number of times. After Changes remaining reaches zero,
the region cannot be changed even Windows is reinstalled or the drive is moved to another computer.
a.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b.
Double-click DVD/CD-ROM drives.
c.
Right-click DVD drive and click Properties, then click the DVD Region tab.
d.
Select the region suitable for the media inserted in the drive.
Discs Do Not Burn Properly
If discs can not be burned, perform the following actions one at a time to correct the problem.
1.
2.
Ensure that the default drive is record enabled:
a.
Navigate to Start´ Computer and right-click the writable ODD icon. Click Properties.
b.
Select the Recording tab. In the Desktop disc recording panel, select the writable ODD from the
drop down list.
c.
Click OK.
Ensure that the software used for burning discs is the factory default. If using different software, refer to
the software's user manual.
Playback is Choppy
If playback is choppy or jumps, perform the following actions one at a time to correct the problem.
1.
2.
Check that system resources are not running low:
a.
Try closing some applications.
b.
Reboot and try the operation again.
Check that the ODD controller transfer mode is set to DMA:
a.
132
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
Chapter 4
b.
Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0.
c.
Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is
checked and click OK.
d.
Repeat for the other ATA Devices shown if applicable.
Drive Not Detected
If Windows cannot detect the drive, perform the following actions one at a time to correct the problem.
1.
Restart the computer and press F2 to enter the BIOS Utility.
2.
Check that the drive is detected in the ATAPI Model Name field on the Information page.
NOTE: Check that the entry is identical to one of the ODDs specified in “Hardware Specifications and
Configurations” on page 13.
3.
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 44.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
4.
Reseat the drive ensuring and all cables are connected correctly.
5.
Replace the ODD. See “Disassembly Process” on page 44.
Drive Read Failure
If discs cannot be read when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Remove and clean the failed disc.
2.
Retry reading the CD or DVD.
d.
Test the drive using other discs.
e.
Play a DVD movie
f.
Listen to a music CD
If the ODD works properly with alternate discs, the original disc is probably defective and should be
replaced.
3.
4.
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 44.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
Replace the ODD. See “Disassembly Process” on page 44.
Chapter 4
133
Wireless Function Failure
If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
Thermal Unit Failure
If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
134
Chapter 4
External Mouse Failure
If an external Mouse fails, perform the following actions one at a time to correct the problem.
1.
Try an alternative mouse.
2.
If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.
3.
If the mouse uses a USB connection, try an alternate USB port.
4.
Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.
5.
Restart the computer.
6.
Remove any recently added hardware and associated software.
7.
Remove any recently added software and reboot.
8.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
9.
Run the Event Viewer to check the events log for errors. For more information see Windows Help and
Support.
10. Roll back the mouse driver to the previous version if updated recently.
11. Remove and reinstall the mouse driver.
12. Check the Device Manager to determine that:
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
13. If the Issue is still not resolved, see “Online Support Information” on page 185.
Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or
Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective
FRUs:
1.
Check Drive whether is OK.
2.
Check Test Fixture is ok.
3.
Swap M/B to Try.
Chapter 4
135
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On
Issue” on page 124.):
136
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery pack
•
Hard disk drive
•
DIMM
•
CD-ROM/Diskette drive Module
•
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
•
System board
•
LCD assembly
Chapter 4
Post Codes
These tables describe the POST codes and descriptions during the POST.
Sec:
NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc)
Code
Description
0xC2
MTRR setup
0xC3
Enable cache
0xC4
Establish cache tags
0xC5
Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0.
0xCF
Cache Init Finished
Memory:
DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC)
Code
Description
0xA0
First memory check point
0x01
Enable MCHBAR
0x02
Check for DRAM initialization interrupt and reset fail
0x03
Verify all DIMMs are DDR or DDR2 and unbuffered
0x04
Detect an improper warm reset and handle
0x05
Detect if ECC SO-DIMMs are present in the system
0x06
Verify all DIMMs are single or double sided and not asymmetric
0x07
Verify all DIMMs are x8 or x16 width
0x08
Find a common CAS latency between the DIMMS and the MCH
0x09
Determine the memory frequency and CAS latency to program
0x10
Determine the smallest common TRAS for all DIMMs
0x11
Determine the smallest common TRP for all DIMMs
0x12
Determine the smallest common TRCD for all DIMMs
0x13
Determine the smallest refresh period for all DIMMs
0x14
Verify burst length of 8 is supported by all DIMMs
0x15
Determine the smallest tWR supported by all DIMMs
0x16
Determine DIMM size parameters
0x17
Program the correct system memory frequency
0x18
Determine and set the mode of operation for the memory channels
0x19
Program clock crossing registers
0x20
Disable Fast Dispatch
0x21
Program the DRAM Row Attributes and DRAM Row Boundary registers
0x22
Program the DRAM Bank Architecture register
0x23
Program the DRAM Timing & and DRAM Control registers
0x24
Program ODT
0x25
Perform steps required before memory init
0x26
Program the receive enable reference timing control register
Program the DLL Timing Control Registers, RCOMP settings
Chapter 4
137
Code
Description
0x27
Enable DRAM Channel I/O Buffers
0x28
Enable all clocks on populated rows
0x29
Perform JEDEC memory initialization for all memory rows
0x30
Perform steps required after memory init
0x31
Program DRAM throttling and throttling event registers
0x32
Setup DRAM control register for normal operation and enable
0x33
Enable RCOMP
0x34
Clear DRAM initialization bit in the SB
0x35
Initialization Sequence Completed, program graphic clocks
0xAF
Disable access to the XMM registers
BDS & Specific action:
Code
138
Description
0x00
Report the legacy boot is happening
0x12
Wake up the Aps
0x13
Initialize SMM Private Data and relocate BSP SMBASE
0x21
PC init begin at the stage1
0x27
Report every memory range do the hardware ECC init
0x28
Report status code of every memory range
0x50
Get the root bridge handle
0x51
Notify pci bus driver starts to program the resource
0x58
Reset the host controller
0x5A
IdeBus begin initialization
0x70
Simple Text Output Protocol Functions(VGA class reset)
0x71
Report that VGA Class driver is being disabled
0x72
Report that VGA Class driver is being enabled
0x78
Terminal Console In reset and Console Out reset
0x79
Report that the remote terminal is being disabled
0x7A
Report that the remote terminal is being enabled
0x90
Keyboard reset
0x91
USB Keyboard disable
0x92
Keyboard detection
0x93
Report that the usb keyboard is being enabled
0x94
Clear the keyboard buffer
0x95
Init Keyboard
0x98
Mouse reset
0x99
Mouse disable
0x9A
Detect PS2 mouse
0x9B
Report that the mouse is being enabled
0xB8
Peripheral removable media reset (ex: IsaFloppy, USB device)
0xB9
Peripheral removable media disable
0xBB
Peripheral removable media enable
0xE4
Report Status Code here for DXE_ENTRY_POINT once it is available
Chapter 4
Code
Description
0xF8
Report that ExitBootServices () has been called
0xF9
Runtime driver set virtual address map
Chapter 4
139
Each PEIM entry point used in 80_PORT
Code
Description
0x00
0x01
PEI_EVENT_LOG
0x02
PEI_OEM_SERVICE
0x03
PEI_SIO_INIT
0x04
PEI_MONO_STATUS_CODE
0x05
PEI_CPU_IO_PCI_CFG
0x06
PEI_CPU_IO
0x07
PEI_PCI_CFG
0x08
PEI_CPU_PEIM
0x09
PEI_PLATFORM_STAGE1
0x0A
PEI_VARIABLE
0x0B
PEI_SB_INIT
0x0C
PEI_CAPSULE
0x0D
PEI_PLATFORM_STAGE2
0x0E
PEI_SB_SMBUS_ARP_DISABLED
0x0F
PEI_HOST_TO_SYSTEM
0x10
PEI_MEMORY_INIT
0x11
PEI_S3_RESUME
0x12
PEI_CLOCK_GEN
0x13
PEI_OP_PRESENCE
0x14
PEI_TPM_TCG
0x15
PEI_FIND_FV
0x16
PEI_H2O_DEBUG_IO
0x17
PEI_H2O_DEBUG_COMM
0x18
PEI_SMM_CONTROL
0x19~0x1F
PEI_RESERVED
0x20~0x2E
PEI_OEM_DEFINED
0x2F
PEI_DXE_IPL
Each Driver entry point used in 80_PORT
Code
140
Description
0x30
RESERVED
0x31
DXE_CRC32_SECTION_EXTRACT
0x32
SCRIPT_SAVE
0x33
ACPI_S3_SAVE
0x34
SMART_TIMER
0x35
JPEG_DECODER
0x36
PCX_DECODER
0x37
HT_CPU / MP_CPU
0x38
LEGACY_METRONOME
0x39
FTWLITE
0x3A
RUN_RIME
Chapter 4
Code
Description
0x3B
MONOTONIC_COUNTER
0x3C
WATCH_DOG_TIMER
0x3D
SECURITY_STUB
0x3E
DXE_CPU_IO
0x3F
CF9_RESET
0x40
PC_RTC
0x41
STATUS_CODE
0x42
VARIABLE
0x43
EMU_VARIABLE
0x44
DXE_CHIPSET_INIT
0x45
DXE_ALERT_FORMAT
0x46
PCI_HOST_BRIDGE
0x47
PCI_EXPRESS
0x48
DXE_SB_INIT
0x49
IDE_CONTROLLER
0x4A
SATA_CONTROLLER
0x4B
SB_SM_BUS
0x4C
ISA_ACPI_DRIVER
0x4D
ISA_BUS
0x4E
ISA_SERIAL
0x4F
IDE_BUS
0x50
PCI_BUS
0x51
BOOT_PRIORITY
0x52
FVB_SERVICE
0x53
ACPI_PLATFORM
0x54
PCI_HOT_PLUG
0x55
DXE_PLATFORM
0x56
PLATFORM_IDE
0x57
SMBIOS
0x58
MEMORY_SUB_CLASS
0x59
MISC_SUB_CLASS
0x5A
CON_PLATFORM
0x5B
SAVE_MEMORY_CONFIG
0x5C
ACPI_SUPPORT
0x5D
CON_SPLITTER_UGA_VGA / CON_SPLITTER
0x5E
VGA_CLASS
0x5F
DATA_HUB
0x60
DISK_IO
0x61
MEMORY_TEST
0x62
CRISIS_RECOVERY
0x63
LEGACY_8259
0x64
LEGACY_REGION
0x65
LEGACY_INTERRUPT
Chapter 4
141
Code
142
Description
0x66
BIOS_KEYBOARD
0x67
BIOS_VEDIO
0x68
MONITER_KEY
0x69
LEGACY_BIOS
0x6A
LEGACY_BIOS_PLATFORM
0x6B
PCI_PLATFORM
0x6C
ISA_FLOOPY
0x6D
PS2_MOUSE
0x6E
USB_BOT
0x6F
USB_CBI0
0x70
USB_CBI1
0x71
USB_KB
0x72
USB_MASS_STORAGE
0x73
BUS_PCI_UHCI
0x74
USB_MOUSE
0x75
USB_BUS
0x76
SETUP_UTILITY
0x77
FW_BLOCK_SERVICE
0x78
USB_LEGACY_PLATFORM
0x79
GRAPHICS_CONSOLE
0x7A
TERMINAL
0x7B
DATA_HUB_STD_ERR
0x7C
FAT
0x7D
PARTITION
0x7E
ENGLISH
0x7F
FRENCH
0x80
HII_DATABASE
0x81
SETUP_BROWSER
0x82
OEM_SETUP_BROWSER
0x83
OEM_BADGING_SUPPORT
0x84
LEGACY_MOUSE
0x85
BIOS_SNP16
0x86
BUS_PCI_UNDI
0x87
SETUP_MOUSE
0x88
OEM_SETTING
0x89
MONITOR_KEY
0x8A
PLATFORM_BDS
0x8B
FAULT_TOLERANT_WRITE
0x8C
UPDATE_DISPATCHER
0x8D
CHINESE
0x8E
TPM_S3_Resume
0x8F
USB_EHCI
0x90
SNP_32_64
Chapter 4
Code
Description
0x91
DXE_0x91 PXE_BC
0x92
PXE_DHCP4
0x93
EBC
0x94~0x9F
RESERVED
0xA0
DXE_H2O_DEBUG_IO
0xA1
DXE_H2O_DEBUG_IO
0xA2
DXE_TPM_TCG
0xA3
DXE_TPM_PHYSICAL_PRESENCE
0xA4
DXE_OEM_SERVICE
0xA5
DXE_EVENT_LOG
0xA6
DXE_ SECURITY_HDD_PASSWORD_SERVICE
0xA7
DXE_LAN_ASF_INIT
0xA8
DXE_BUS_PCI_SERIAL
0xA9
DXE_LAN_IDER_CONTROLLER
0xAA
DXE_LAN_AMT
0xAB
DXE_ SECURITY_SYSTEM_PASSWORD_SERVICE
0xAC
DXE_ SECURITY_ PASSWORD_CONSOLE
0xAD
DXE_ DATA_HUB_RECORD_POLICY
0xAE
DXE_TPM_DRIVER
0xAF
RESERVED
0xB0
JAPANESE
0xB1
DXE_UNICODE_COLLACTION
Chapter 4
143
Each SmmDriver entry point used in 80_PORT
Code
Description
0xC0
SMM_ACCESS
0xC2
SMM_CONTROL
0xC1
SMM_BASE
0xC3
SMMAP
0xC4
SMMCORE
0xC5
SMM_DISPATCH
0xC6
SMM_START
0xC7
SMM_RUNTIME
0xC8
SB_SMM_DISPATCH
0xC9
SMM_THUNK
0xCA
SMM_ACPI_SW_CHILD
0xCB
SMM_SB_S3_SAVE
0xCC
SMM_PLATFORM
0xCD
SMM_GMCH_MBI
0xCE
SMM_FW_BLOCK_SERVICE
0xCF
SMM_VARIABLE
0xD0
SMM_IHISI
0xD1
SMM_INT15_MICROCODE
0xD2
SMM_PNP
0xD3
SMM_USB_LEGACY
0xD4
SMM_INT13_HDD
0xD5
SMM_INIT_PPM
0xD6
SMM_OHCI1394
0xD7
SMM_ SECURITY_HDD_PASSWORD_SERVICE
0xD8
SMM_OEM_SERVICE
0xD9
SMM_PPM
0xDA
SMM_DIGITAL_THERMAL_SENSOR
* If the BIOS detects error 2C, 2E, or 30 (base 512K RAM error), it displays an additional word-bitmap (xxxx)
indicating the address line or bits that failed. For example, 2C 0002 means address line 1 (bit one set) has
failed. 2E 1020 means data bits 12 and 5 (bits 12 and 5 set) have failed in the lower 16 bits. Note that error 30
cannot occur on 386SX systems because they have a 16 rather than 32-bit bus. The BIOS also sends the
bitmap to the port-80 LED display. It first displays the check point code, followed by a delay, the high-order
byte, another delay, and then the low-order byte of the error. It repeats this sequence continuously.
144
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
Item
Chapter 5
Description
JLVDS1
LCD Connector
JP14
Power/B Connector
JSPK1
Speaker(Left) Connector
JSPK2
Speaker(Right) Connector
JKB2
Internal Keyboard Connector
JTP1
Touch Pad Connector
U11
South Bridge
SW4
Touch pad (Left) Button
SW3
Touch pad (Right) Button
145
Bottom View
146
ITEM
DESCRIPTION
PJP1
AC-IN Connector
JRJ45
RJ45 Connector
JCRT1
CRT Connector
JP12
Fan Connector
JUSB1
USB Connector
JUSB2
USB Connector
JMIC1
MIC-In Jack
JHP1
Head-Phone Jack
JSATA2
HDD Connector
U23
North Bridge
JCPU1
CPU Socket
JREAD1
Card Reader Socket
PJP3
Battery Board Connector
JDIMM2
Memory DIMM2 Connector
JDIMM1
Memory DIMM1 Connector
PJP2
ODD Board Connector
JMINI2
Wireless Card Connector
Chapter 5
Power Board
ITEM
DESCRIPTION
SW1
TP Lock Button
SW2
ON/OFF Button
SW3
Wireless Button
LED1
ON/OFF LED
LED3
Media LED
LED4
Num LED
LED5
Wireless LED
LED6
Caps LED
LED7
TP Lock LED
LS-4852P ODD Board
Chapter 5
ITEM
DESCRIPTION
JP1
M/B Connector
JP2
HDD Connector
JP3
ODD Board Connector
147
LS-4853P Battery Board
ITEM
DESCRIPTION
PIP1
M/B Connector
PIP2
Battery Connector
LS-4854P Lid Board
148
ITEM
DESCRIPTION
U1
Lid Switch
Chapter 5
Clearing Password Check and BIOS Recovery
This section provides you with the standard operating procedures of clearing password and BIOS recovery for
eMachine HM70-MV. The machine provides one Hardware Open Gap on main board for clearing password
check, and one Hotkey for enabling BIOS Recovery.
Clearing Password Check
Steps for Clearing BIOS Password Check
If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is
necessary to bypass the password check, users need to short the HW Gap to clear the password by the
following steps:
1.
Power Off the system, and remove HDD, AC and Battery from the machine.
2.
Disconnect the RTC Battery cable and locate the J1 jumper.
3.
Use an electric conductivity tool to short the two points of the HW Gap.
4.
Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the system till
BIOS POST finish. Then remove the tool from the HW Gap.
5.
Restart system. Press F2 key to enter BIOS Setup menu.
6.
If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and try
again.
NOTE: These steps are only for clearing BIOS Password (Supervisor Password and User Password).
Clear CMOS Jumper
Chapter 5
Item
Description
J1
Clear CMOS Jumper
149
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:
BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous
BIOS flashing process failed.
BIOS Recovery Hotkey:
The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot
Block.
Steps for BIOS Recovery from USB Storage:
Before doing this, prepare the Crisis USB key. The Crisis USB key could be made by executing the Crisis Disk
program in another system with Windows XP OS.
Follow the steps below:
1.
Format the USB storage disk using the Fast Format option.
2.
Save ROM file (file name: JAL90x64.fd) to the root directory of USB storage. Make sure that there is no
other BIOS file saved in the same directory.
3.
Plug USB storage into USB port.
4.
Press Fn + ESC button then plug in AC power.
The Power button flashes once.
5.
Press Power button to initiate system CRISIS mode.
When CRISIS is complete, the system auto restarts with a workable BIOS.
6.
150
Update the latest version BIOS for this machine by regular BIOS flashing process.
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 7715Z/7315. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6
151
Aspire 7715Z/7315 Exploded Diagrams
Main Assembly
1
2
4
3
5
6
7
8
No.
Description
1
Middle Cover
2
Up Cap (L)
3
Upper Cover
4
Up Cap (R)
5
Mainboard
Acer P/N
6
7
8
152
Lower Cover
Chapter 6
Base Assembly
1
2
3
4
5
No.
Description
1
CPU Fan
2
Thermal Module
Acer P/N
3
4
5
Chapter 6
Mainboard
153
Rear Assembly
3
4
1
2
5
No.
1
Description
Acer P/N
HDD Cover
2
3
RAM Cover
4
5
154
Chapter 6
Aspire 7715Z/7315 FRU List
CATEGORY
DESCRIPTION
AcerPN
ADAPTER
Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP65JH DB A, LV5 LED LF
AP.06501.026
Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA1650-22AC LV5 LED LF
AP.06503.024
Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HPA0652R3B 1LF, LV5 LED LF
AP.0650A.012
Battery SANYO AS-2009A Li-Ion 3S2P SANYO 6 cell
4400mAh Main COMMON 2.2Ah(A)
BT.00603.076
Battery SONY AS-2009A Li-Ion 3S2P SONY 6 cell
4400mAh Main COMMON 2.2Ah(G6F)
BT.00604.030
Battery PANASONIC AS-2009A Li-Ion 3S2P
PANASONIC 6 cell 4400mAh Main COMMON
2.2Ah(CG )
BT.00605.036
Battery SAMSUNG AS-2009A Li-Ion 3S2P SAMSUNG
6 cell 4400mAh Main COMMON 2.2Ah(F)
BT.00606.002
Battery SIMPLO AS-2009A Li-Ion 3S2P PANASONIC
6 cell 4400mAh Main COMMON Panasonic 2.2Ah (
CG )
BT.00607.066
Battery SIMPLO AS-2009A Li-Ion 3S2P LGC 6 cell
4400mAh Main COMMON LGC 2.2Ah(S3 )
BT.00607.067
Battery SIMPLO AS-2009A Li-Ion 3S2P SAMSUNG 6
cell 4400mAh Main COMMON SDI 2.2Ah(F)
BT.00607.068
POWER BOARD
55.N3702.001
ODD BOARD
55.N3702.002
BATTERY BOARD
55.N3702.003
Foxconn FOX_ATH_XB63 Foxconn Atheros XB63
minicard b/g
NI.23600.007
Foxconn Wireless LAN Broadcom 4312 minicard b/g
NI.23600.029
Foxconn Wireless LAN Broadcom 4312H BG (HM)
NI.23600.053
Foxconn Wirelss LAN Atheros HB95 1x1 BG (HM)
NI.23600.047
BATTERY
BOARD
Chapter 6
Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM)
NI.23600.046
Liteon Wireless LAN Reltek RTL8191SE (WN6605LH)
(1x1)
NI.23600.056
Foxconn Wireless LAN Broadcomm 43225 BGN (HM)
NI.23600.058
155
CATEGORY
DESCRIPTION
AcerPN
CABLE
TP FFC
50.N3702.001
POWER CORD US 3 PIN
27.TAVV5.001
POWER CORD EU 3 PIN
27.TAVV5.002
POWER CORD AUS 3 PIN
27.TAVV5.003
POWER CORD UK 3 PIN
27.TAVV5.004
POWER CORD CHINA 3 PIN
27.TAVV5.005
POWER CORD SWISS 3 PIN
27.TAVV5.006
POWER CORD ITALIAN 3 PIN
27.TAVV5.007
POWER CORD DENMARK 3 PIN
27.TAVV5.008
POWER CORD JP 3 PIN
27.TAVV5.009
POWER CORD SOUTH AFRICA 3 PIN
27.TAVV5.010
POWER CORD KOERA 3 PIN
27.TAVV5.011
POWER CORD ISRAEL 3 PIN
27.TAVV5.012
POWER CORD INDIA 3 PIN
27.TAVV5.013
POWER CORD TWN 3 PIN
27.TAVV5.014
POWER CORD ARGENTINA 3 PIN
27.APV02.001
CASE/COVER/BRACKET ASSEMBLY
156
UPPER CASE ASSY
60.N3702.001
UPPER CASE ASSY, INCL.TP & TP MYLAR ASPIRE
60.PL602.001
LOWER CASE
60.N3702.002
LOWER CASE WASHER
47.N3702.001
TP BRACKET
33.N3702.001
MIDDLE COVER - ASPIRE
60.PL602.002
HINGE CAP ASSY
42.N3702.001
Chapter 6
CATEGORY
DESCRIPTION
AcerPN
RAM DOOR ASSY
42.N3702.002
HDD DOOR ASSY
42.N3702.003
2ND HDD DOOR ASSY
42.N3702.004
MINI CARD BRK
33.PGY02.001
33.N6602.001
CPU Intel CeleronM T1600 1.66G 1M 667 Dual Core,
MV
KC.16001.CMT
CPU Intel CeleronM T1700 PGA 1.83G 1M 667 Dual
Core, MV
KC.17001.CMT
CPU Intel Pentium Dual-Core T3400 PGA 2.16G 1M
667 MV
KC.34001.DTP
CPU Intel Pentium Dual-Core T4200 PGA 2.0G 1M
800 35W R-0 no VT
KC.42001.DTP
CPU Intel Celeron 575 PGA 2.0G 1M 667 MV
KC.N0001.575
CPU/PROCESSOR
CPU Intel Celeron 585 PGA 2.16G 1M 667 MV
KC.N0001.585
CPU Intel Celeron 900 PGA 2.2G 1M 800 35W
KC.N0001.900
HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS
Crockett SATA LF F/W:0303
KH.16001.034
HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX
Libra SATA LF F/W: FG011J
KH.16004.006
HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300
Falcon-B SATA LF F/W:C40C
KH.16007.019
HDD WD 2.5" 5400rpm 160GB WD1600BEVT22ZCTO ML160 SATA LF F/W:11.01A11
KH.16008.022
HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS
Wyatt SATA LF F/W:0001SDM1
KH.25001.016
HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX
Libra SATA LF F/W:FG001J
KH.25004.003
HDD HGST 2.5" 5400rpm 250GB HTS545025B9A300
Panther B SATA LF F/W:C60F
KH.25007.015
HDD WD 2.5" 5400rpm 250GB WD2500BEVT22ZCT0 ML160 SATA LF F/W:11.01A11
KH.25008.021
HDD SEAGATE 2.5" 5400rpm 320GB ST9320320AS
Crockett SATA LF F/W:0303
KH.32001.008
HDD/HARD DISK DRIVE
Chapter 6
157
CATEGORY
DESCRIPTION
AcerPN
HDD TOSHIBA 2.5" 5400rpm 320GB MK3255GSX
Libra SATA LF F/W:FG011J
KH.32004.002
HDD HGST 2.5" 5400rpm 320GB HTS545032B9A300
Panther B SATA LF F/W: C60F
KH.32007.007
HDD WD 2.5" 5400rpm 320GB WD3200BEVT22ZCT0 ML160 SATA LF F/W:11.01A11
KH.32008.013
HDD SEAGATE 2.5" 5400rpm 500GB ST9500325AS
Wyatt SATA LF F/W:0001SDM1
KH.50001.011
HDD WD 2.5" 5400rpm 500GB WD5000BEVT22ZAT0 ML250 SATA LF F/W:01.01A01
KH.50008.013
HDD HGST 2.5" 5400rpm 500GB HTS545050B9A300
Panther B SATA LF F/W:C60F
KH.50007.009
HDD BRACKET ASSY
33.N3702.002
DVD SUPER MULTI DRIVE MODULE
6M.N3702.001
DVD SUPER MULTI DRIVE MODULE - Win 7
6M.PL802.001
ODD PANASONIC Super-Multi DRIVE 12.7mm Tray
DL 8X UJ880A LF W/O bezel SATA
KU.00807.064
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X
GT20N LF W/O bezel SATA
KU.0080D.040
ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X
AD-7580S LF W/O bezel SATA
KU.0080E.017
ODD PLDS Super-Multi DRIVE 12.7mm Tray DL 8X
DS-8A3S LF W/O bezel SATA
KU.0080F.004
ODD BRACKET
33.N3702.003
ODD BEZEL-SUPER MULTI
42.N3702.005
DVD DRIVE
158
Chapter 6
CATEGORY
DESCRIPTION
AcerPN
KEYBOARD
Chapter 6
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black Greek
KB.I1700.423
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black Arabic
KB.I1700.414
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black Russian
KB.I1700.430
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black Thailand
KB.I1700.435
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black UK
KB.I1700.437
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black German
KB.I1700.422
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Swiss/G
KB.I1700.434
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Belgium
KB.I1700.415
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Danish
KB.I1700.419
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Italian
KB.I1700.425
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black French
KB.I1700.421
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Hungarian
KB.I1700.424
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Norwegian
KB.I1700.428
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Portuguese
KB.I1700.429
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Spanish
KB.I1700.432
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Turkish
KB.I1700.436
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Sweden
KB.I1700.433
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black SLO/CRO
KB.I1700.431
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Nordic
KB.I1700.427
159
CATEGORY
DESCRIPTION
AcerPN
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black US International
KB.I1700.438
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black Chinese
KB.I1700.418
Keyboard EM-7T HM50/70 Internal 17 Standard 99KS
Black US International w/ Hebrew
KB.I1700.439
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black FR/Arabic
KB.I1700.420
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black US w/ Canadian French
KB.I1700.440
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black Brazilian Portuguese
KB.I1700.416
Keyboard EM-7T HM50/70 Internal 17 Standard
100KS Black CZ/SK
KB.I1700.417
Keyboard EM-7T HM50/70 Internal 17 Standard
103KS Black Japanese
KB.I1700.426
ASSY LED MODULE 17.3 IN. WXGA GLARE W/
ANTENNA*2 CCD 0.3M - ASPIRE
6M.PL602.001
ASSY LED MODULE 17.3 IN. WXGA GLARE W/
ANTENNA*3 CCD 0.3M - ASPIRE
6M.PL602.002
ASSY LED MODULE 17.3 IN. WXGA GLARE W/
ANTENNA*2, W/O CCD - ASPIRE
6M.PL802.002
ASSY LED MODULE 17.3 IN. WXGA GLARE W/
ANTENNA*3, W/O CCD - ASPIRE
6M.PL802.003
LED LCD AUO 17.3" WXGA+ Glare B173RW01-V0 LF
220nit 8ms 600:1
LK.17305.001
LED LCD SAMSUNG 17.3" WXGA+ Glare
LTN173KT01-A01 LF 220nit 8ms 600:1
LK.17306.001
LED LCD LPL 17.3" WXGA+ Glare LP173WD1-TLA1
LF 220nit 8ms 600:1
LK.17308.001
LED LCD CMO 17.3" WXGA+ Glare N173O6-L02 LF
220nit 8ms 600:1
LK.1730D.001
LCD COVER - ASPIRE
60.PL602.003
ANTENNA MAIN
50.N3702.002
LCD
160
Chapter 6
CATEGORY
DESCRIPTION
AcerPN
ANTENNA AUX
50.N3702.004
LCD BEZEL FOR W/CCD FUNCTION - ASPIRE
60.PL602.004
LCD BEZEL FOR W/O CCD FUNCTION - ASPIRE
60.PL502.001
LED CABLE FOR W/CCD F
60.N3702.006
LCD BRACKET R&L FOR LED F
33.N3702.004
CAMERA 0.3
57.N2802.001
MB ASSY-GM45(B3)-INTEL
MB.N5302.001
MB ASSY-GM45(A1)-INTEL
TBD
MB ASSY-GL40-(B3)-INTEL
TBD
Mainboard AS7715Z Intel GL40 ICH9M V1.0 LF
MB.PL402.001
Mainboard G525 Intel GL40 ICH9M V1.0 LF DDR3
MB.N8302.001
Memory NANYA SO-DIMM DDRII 667 1GB
NT1GT64UH8D0FN-3C LF 64*16 0.07um
KN.1GB03.026
Memory MICRON SO-DIMM DDRII 667 1GB
MT8HTF12864HDY-667G1 LF 64*16 0.065um
KN.1GB04.010
Memory ELPIDA SO-DIMM DDRII 667 1GB
EBE11UE6ACUA-6E-E LF 64*16 0.065um
KN.1GB09.008
Memory SAMSUNG SO-DIMM DDRII 667 1GB
M470T2864EH3-CE6 LF 64*16 0.055um
KN.1GB0B.027
Memory HYNIX SO-DIMM DDRII 667 1GB
HYMP112S64CP6-Y5 LF
KN.1GB0G.012
Memory HYNIX SO-DIMM DDRII 667 1GB
HMP112S6EFR6C-Y5 LF 64*16 0.055um
KN.1GB0G.022
Memory NANYA SO-DIMM DDRII 667 2GB
NT2GT64U8HD0BN-3C LF 128*8 0.07um
KN.2GB03.011
Memory MICRON SO-DIMM DDRII 667 2GB
MT16HTF25664HY-667G1 LF 128*8 0.065um
KN.2GB04.010
MAINBOARD
MEMORY
Chapter 6
161
CATEGORY
DESCRIPTION
AcerPN
Memory ELPIDA SO-DIMM DDRII 667 2GB
EBE21UE8ACUA-6E-E LF 128*8 0.07um
KN.2GB09.001
Memory SAMSUNG SO-DIMM DDRII 667 2GB
M470T5663EH3-CE6 LF 128*8 0.055um
KN.2GB0B.011
Memory HYNIX SO-DIMM DDRII 667 2GB
HYMP125S64CP8-Y5 LF
KN.2GB0G.004
Memory HYNIX SO-DIMM DDRII 667 2GB
HMP125S6EFR8C-Y5 LF 128*8 0.055um
KN.2GB0G.012
THERMAL MODULE-INTEL
60.N3702.007
FAN
23.N3702.001
SPEAKER R
23.N3702.002
SPEAKER L
23.N3702.003
NAME PLATE-AS7715
40.PL502.001
NAME PLATE-AS7315
40.PL802.001
HEATSINK
SPEAKER
MISCELLANEOUS
162
Chapter 6
Screw List
CATEGORY
DESCRIPTION
Acer PN
SCREW
Chapter 6
SCREW M2.48D 4.0L K 5.5D 0.8T ZKNL
86.N3702.001
SCREW M2.48D 6.0L K 5.5D 0.8T ZKNL
86.N3702.002
SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL
86.N3702.003
SCREW M1.98D 3.0L K 4.6D 0.8T ZKNL
86.N3702.004
SCREW M M 2D 5L K 4.6D NI NL+
86.N3702.005
SCREW M M 3.0D 3.0L K 4.9D NI+
86.N3702.006
SCREW ASSY CPU THERMAL
86.N3702.007
163
Appendix A
Model Definition and Configuration
Appendix A
164
Aspire 7315
Model
Acer Part No
RO
Country
AS7315903G50Mi
S2.PL602.001
WW
WW
AS7315-903G50Mi W7HP64AWW1 UMACks
2G+1G/500_L/6L2.2/5R/CB_bg_0.3D_HG_ES62
AS7315313G25Mn
LX.PNL02.001
EMEA
UK
AS7315-313G25Mn W7HP64ATGB1 MC UMACks_3
2G+1G/250/6L2.2/5R/CB_bgn_0.3D_HG_EN11
AS7315902G25Mn
S2.PNL02.001
WW
WW
AS7315-902G25Mn W7HP64AWW1 MC UMACks_3
1*2G/250/6L2.2/5R/CB_bgn_0.3D_HG_ES62
AS7315302G25Mn
S2.PL80C.001
WW
WW
AS7315-302G25Mn LINPUSAWW1 UMAks 1*2G/
250/6L2.2/5R/CB_bgn_HG_EN11
AS7315902G25Mn
S2.PNM0C.001
WW
WW
AS7315-902G25Mn LINPUSAWW1 UMAks_3 2*1G/
250/6L2.2/5R/CB_bgn_HG_EN11
Model
Acer Part No
CPU
Description
LCD
VGA
Chip
VRAM
1
Memory 1
Memory 2
AS7315903G50Mi
S2.PL602.001
CM900
NLED17.3
WXGA+G
UMA
N
SO2GBII6
SO1GBII6
AS7315313G25Mn
LX.PNL02.001
CMT3100
NLED17.3
WXGA+G
UMA
N
SO2GBIII
10
SO1GBIII1
0
AS7315902G25Mn
S2.PNL02.001
CM900
NLED17.3
WXGA+G
UMA
N
SO2GBIII
10
N
AS7315302G25Mn
S2.PL80C.001
CMT3000
NLED17.3
WXGA+G
UMA
N
SO2GBII6
N
AS7315902G25Mn
S2.PNM0C.001
CM900
NLED17.3
WXGA+G
UMA
N
SO1GBIII
10
SO1GBIII1
0
Model
Acer Part No
Memory
3
Memory
4
HDD
1(GB)
HDD
2(GB)
ODD
Media
Processor
AS7315903G50Mi
S2.PL602.001
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7315313G25Mn
LX.PNL02.001
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7315902G25Mn
S2.PNL02.001
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7315302G25Mn
S2.PL80C.001
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7315902G25Mn
S2.PNM0C.001
N
N
N250GB
5.4KS
N
NSM8XS
N
Model
Acer Part No
Extra
SW1
Card Reader
Wireless LAN1
Bluetooth
VOIP
Phone
AS7315903G50Mi
S2.PL602.001
NIS
5 in 1-Build in
3rd WiFi BG
N
N
AS7315313G25Mn
LX.PNL02.001
McAfee
5 in 1-Build in
3rd WiFi 1x2
BGN
N
N
AS7315902G25Mn
S2.PNL02.001
McAfee
5 in 1-Build in
3rd WiFi 1x2
BGN
N
N
165
Appendix A
Model
Acer Part No
Extra
SW1
Card Reader
Wireless LAN1
Bluetooth
VOIP
Phone
AS7315302G25Mn
S2.PL80C.001
N
5 in 1-Build in
3rd WiFi 1x2
BGN
N
N
AS7315902G25Mn
S2.PNM0C.001
N
5 in 1-Build in
3rd WiFi 1x2
BGN
N
N
Appendix A
166
Aspire 7715Z
Model
Acer Part No
RO
Country
Description
AS7715Z433G25Mi
S2.PL40C.001
WW
WW
AS7715Z-433G25Mi LINPUSAWW1
UMACks 2G+1G/250/6L2.2/5R/
CB_bg_0.3D_HG_EN11
AS7715Z443G25Mn
LX.PNJ02.016
EMEA
UK
AS7715Z-443G25Mn W7HP64ATGB1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_EN11
AS7715Z444G32Mn
LX.PNJ02.045
EMEA
UK
AS7715Z-444G32Mn W7HP64ATGB1 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_EN11
AS7715Z444G32Mn
LX.PNJ02.057
EMEA
France
AS7715Z-444G32Mn W7HP64ATFR1 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_FR21
AS7715Z443G32Mn
LX.PNJ02.061
EMEA
Holland
AS7715Z-443G32Mn W7HP64ATNL1 MC
UMACks_3 2G+1G/320/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z442G32Mn
LX.PNJ0C.007
EMEA
Poland
AS7715Z-442G32Mn LINPUSAPL1
UMACks_3 1*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_EN41
AS7715Z444G50Mn
LX.PNJ02.070
EMEA
Holland
AS7715Z-444G50Mn W7HP64ATNL1 MC
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z443G32Mn
LX.PNJ02.062
EMEA
Belgium
AS7715Z-443G32Mn W7HP64ATBE1 MC
UMACks_3 2G+1G/320/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z444G64Mn
LX.PNJ02.065
EMEA
Belgium
AS7715Z-444G64Mn W7HP64ATBE1 MC
UMACks_3 2*2G/640/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z444G50Mn
LX.PNJ02.069
EMEA
Belgium
AS7715Z-444G50Mn W7HP64ATBE1 MC
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z444G50Mn
LX.PNJ02.068
EMEA
Luxembourg
AS7715Z-444G50Mn W7HP64ATLU3 MC
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z444G25Mn
LX.PNJ02.067
EMEA
Eastern
Europe
AS7715Z-444G25Mn W7HP64ATEU4 MC
UMACks_3 2*2G/250/6L2.2/5R/
CB_bgn_0.3D_HG_SV21
AS7715Z444G25Mn
LX.PNJ02.066
EMEA
Latvia
AS7715Z-444G25Mn W7HP64ATLV1 MC
UMACks_3 2*2G/250/6L2.2/5R/
CB_bgn_0.3D_HG_LT11
AS7715Z444G32Mn
LX.PNJ02.059
EMEA
Switzerland
AS7715Z-444G32Mn W7HP64ATCH1 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z444G64Mn
LX.PNJ02.064
EMEA
Holland
AS7715Z-444G64Mn W7HP64ATNL1 MC
UMACks_3 2*2G/640/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z444G64Mn
LX.PNJ02.063
EMEA
Luxembourg
AS7715Z-444G64Mn W7HP64ATLU3 MC
UMACks_3 2*2G/640/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z443G32Mn
LX.PNJ02.060
EMEA
Luxembourg
AS7715Z-443G32Mn W7HP64ATLU3 MC
UMACks_3 2G+1G/320/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
167
Appendix A
Model
Acer Part No
RO
Country
AS7715Z442G32Mn
LX.PNJ02.058
EMEA
Switzerland
AS7715Z-442G32Mn W7HP64ATCH1 MC
UMACks_3 1*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z434G50Mn
LX.PNJ02.050
EMEA
Norway
AS7715Z-434G50Mn W7HP64ATNO3 MC
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_ENS1
AS7715Z434G32Mn
LX.PNJ02.049
EMEA
Norway
AS7715Z-434G32Mn W7HP64ATNO3 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_ENS1
AS7715Z444G64Mn
LX.PNJ02.054
EMEA
Switzerland
AS7715Z-444G64Mn W7HP64ATCH1 MC
UMACks_3 2*2G/640/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z444G32Mn
LX.PNJ02.041
EMEA
Denmark
AS7715Z-444G32Mn W7HP64ATDK2 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_ENS1
AS7715Z444G50Mn
LX.PNJ02.052
EMEA
France
AS7715Z-444G50Mn W7HP64ATFR1 MC
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_FR21
AS7715Z444G32Mn
LX.PNJ0C.008
EMEA
Poland
AS7715Z-444G32Mn LINPUSAPL1
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_EN41
AS7715Z442G25Mn
LX.PNJ02.056
EMEA
Switzerland
AS7715Z-442G25Mn W7HP64ATCH1 MC
UMACks_3 1*2G/250/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z444G50Mn
LX.PNJ0C.005
EMEA
Eastern
Europe
AS7715Z-444G50Mn LINPUSAEU7
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_ENQ1
AS7715Z444G50Mn
LX.PNJ02.053
EMEA
Switzerland
AS7715Z-444G50Mn W7HP64ATCH1 MC
UMACks_3 2*2G/500_L/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z443G32Mn
LX.PNJ0C.004
EMEA
Eastern
Europe
AS7715Z-443G32Mn LINPUSAEU5
UMACks_3 2G+1G/320/6L2.2/5R/
CB_bgn_0.3D_HG_ENF1
AS7715Z444G32Mn
LX.PNJ02.044
EMEA
Norway
AS7715Z-444G32Mn W7HP64ATNO3 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_ENS1
AS7715Z444G32Mn
LX.PNJ02.043
EMEA
Finland
AS7715Z-444G32Mn W7HP64ATFI2 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_FI12
AS7715Z444G32Mn
LX.PNJ02.042
EMEA
Sweden
AS7715Z-444G32Mn W7HP64ATSE1 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_FI12
AS7715Z443G25Mn
LX.PNJ02.040
EMEA
Ukraine
AS7715Z-443G25Mn W7HP64RUATUK1
MC UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_RU61
AS7715Z443G25Mi
LX.PNJ02.039
EMEA
Russia
AS7715Z-443G25Mi W7HP64RUATRU1
MC UMACks_3 2G+1G/250/6L2.2/5R/
CB_bg_0.3D_HG_RU11
AS7715Z443G25Mn
LX.PNJ02.038
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME4 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_RU61
Appendix A
Description
168
Model
Acer Part No
RO
Country
AS7715Z443G25Mn
LX.PNJ02.037
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME2 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES61
AS7715Z443G25Mn
LX.PNJ02.036
EMEA
South Africa
AS7715Z-443G25Mn EM
W7HP64EMATZA2 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES61
AS7715Z443G25Mn
LX.PNJ02.035
EMEA
Turkey
AS7715Z-443G25Mn EM
W7HP64EMATTR1 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_TR31
AS7715Z443G25Mn
LX.PNJ02.034
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME2 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_AR21
AS7715Z443G25Mn
LX.PNJ02.033
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME9 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES81
AS7715Z443G25Mn
LX.PNJ02.032
EMEA
Algeria
AS7715Z-443G25Mn EM
W7HP64EMATDZ1 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES81
AS7715Z443G25Mn
LX.PNJ02.031
EMEA
South Africa
AS7715Z-443G25Mn EM
W7HP64EMATZA1 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES81
AS7715Z443G25Mn
LX.PNJ02.030
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME4 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES61
AS7715Z443G25Mn
LX.PNJ02.029
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME2 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_AR11
AS7715Z443G25Mn
LX.PNJ02.028
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME3 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES81
AS7715Z443G25Mn
LX.PNJ02.027
EMEA
Middle East
AS7715Z-443G25Mn EM
W7HP64EMATME6 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES61
AS7715Z443G25Mn
LX.PNJ02.026
EMEA
South Africa
AS7715Z-443G25Mn EM
W7HP64EMATZA4 MC UMACks_3
2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES61
AS7715Z443G25Mn
LX.PNJ02.025
EMEA
Germany
AS7715Z-443G25Mn W7HP64ATDE1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_DE11
AS7715Z443G25Mn
LX.PNJ02.024
EMEA
Poland
AS7715Z-443G25Mn W7HP64ATPL1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_PL11
169
Description
Appendix A
Model
Acer Part No
RO
AS7715Z443G25Mn
LX.PNJ02.023
EMEA
Luxembourg
AS7715Z-443G25Mn W7HP64ATLU3 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z443G25Mn
LX.PNJ02.022
EMEA
Holland
AS7715Z-443G25Mn W7HP64ATNL1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z443G25Mn
LX.PNJ02.021
EMEA
Belgium
AS7715Z-443G25Mn W7HP64ATBE1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_NL11
AS7715Z443G25Mn
LX.PNJ02.020
EMEA
Switzerland
AS7715Z-443G25Mn W7HP64ATCH1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_IT41
AS7715Z443G25Mn
LX.PNJ02.019
EMEA
Denmark
AS7715Z-443G25Mn W7HP64ATDK2 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ENS1
AS7715Z443G25Mn
LX.PNJ02.018
EMEA
Eastern
Europe
AS7715Z-443G25Mn W7HP64ATEU5 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_RO11
AS7715Z443G25Mn
LX.PNJ02.017
EMEA
Eastern
Europe
AS7715Z-443G25Mn W7HP64ATEU5 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_PL71
AS7715Z443G25Mn
LX.PNJ02.015
EMEA
Latvia
AS7715Z-443G25Mn W7HP64ATLV1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_RU22
AS7715Z443G25Mn
LX.PNJ02.014
EMEA
Czech
AS7715Z-443G25Mn W7HP64ATCZ2 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_SK11
AS7715Z443G25Mn
LX.PNJ02.013
EMEA
Hungary
AS7715Z-443G25Mn W7HP64ATHU1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_HU11
AS7715Z443G25Mn
LX.PNJ02.012
EMEA
Israel
AS7715Z-443G25Mn W7HP64ATIL1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_HE11
AS7715Z443G25Mn
LX.PNJ02.011
EMEA
Cyprus
AS7715Z-443G25Mn W7HP64ATCY1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES61
AS7715Z443G25Mn
LX.PNJ02.010
EMEA
Portugal
AS7715Z-443G25Mn W7HP64ATPT1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_PT11
AS7715Z443G25Mn
LX.PNJ02.009
EMEA
Eastern
Europe
AS7715Z-443G25Mn W7HP64ATEU7 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ENQ1
AS7715Z443G25Mn
LX.PNJ02.008
EMEA
Eastern
Europe
AS7715Z-443G25Mn W7HP64ATEU4 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_SV21
AS7715Z443G25Mn
LX.PNJ02.006
EMEA
Spain
AS7715Z-443G25Mn W7HP64ATES1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_ES51
AS7715Z443G25Mn
LX.PNJ02.007
EMEA
Italy
AS7715Z-443G25Mn W7HP64ATIT1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_IT11
Appendix A
Country
Description
170
Model
Acer Part No
RO
AS7715Z443G25Mn
LX.PNJ02.005
EMEA
Serbia/
Macedonia
AS7715Z-443G25Mn W7HP64ATCS1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_SL11
AS7715Z443G25Mn
LX.PNJ02.004
EMEA
Greece
AS7715Z-443G25Mn W7HP64ATGR1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_EL31
AS7715Z443G25Mn
LX.PNJ02.003
EMEA
Austria
AS7715Z-443G25Mn W7HP64ATAT1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_DE61
AS7715Z443G25Mn
LX.PNJ02.002
EMEA
France
AS7715Z-443G25Mn W7HP64ATFR1 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_FR21
AS7715Z443G25Mn
LX.PNJ02.001
EMEA
Eastern
Europe
AS7715Z-443G25Mn W7HP64ATEU7 MC
UMACks_3 2G+1G/250/6L2.2/5R/
CB_bgn_0.3D_HG_SL11
AS7715Z434G32Mn
S2.PNJ02.001
WW
WW
AS7715Z-434G32Mn W7HP64AWW1 MC
UMACks_3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_HG_ES62
AS7715Z432G32Mi
S2.PL50C.001
WW
WW
AS7715Z-432G32Mi LINPUSAWW1
UMAks 1*2G/320/6L2.2/5R/
CB_bg_HG_EN11
AS7715Z432G16Mn
S2.PNK0C.001
WW
WW
AS7715Z-432G16Mn LINPUSAWW1
UMAks_3 2*1G/160/6L2.2/5R/
CB_bgn_HG_EN11
Model
Acer Part No
CPU
LCD
AS7715Z433G25Mi
S2.PL40C.001
PMDT4
300
NLED17.3
WXGA+G
UMA
N
SO2GBII6
SO1GBII6
AS7715Z443G25Mn
LX.PNJ02.016
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z444G32Mn
LX.PNJ02.045
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G32Mn
LX.PNJ02.057
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z443G32Mn
LX.PNJ02.061
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z442G32Mn
LX.PNJ0C.007
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
N
AS7715Z444G50Mn
LX.PNJ02.070
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z443G32Mn
LX.PNJ02.062
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z444G64Mn
LX.PNJ02.065
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G50Mn
LX.PNJ02.069
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G50Mn
LX.PNJ02.068
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G25Mn
LX.PNJ02.067
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
171
Country
Description
VGA
Chip
VRAM
1
Memory 1
Memory 2
Appendix A
VGA
Chip
Model
Acer Part No
CPU
LCD
AS7715Z444G25Mn
LX.PNJ02.066
PMDT4
400
NLED17.3
WXGA+G
UMA
AS7715Z444G32Mn
LX.PNJ02.059
PMDT4
400
NLED17.3
WXGA+G
AS7715Z444G64Mn
LX.PNJ02.064
PMDT4
400
AS7715Z444G64Mn
LX.PNJ02.063
AS7715Z443G32Mn
VRAM
1
Memory 1
Memory 2
N
SO2GBIII10
SO2GBIII10
UMA
N
SO2GBIII10
SO2GBIII10
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
LX.PNJ02.060
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z442G32Mn
LX.PNJ02.058
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
N
AS7715Z434G50Mn
LX.PNJ02.050
PMDT4
300
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z434G32Mn
LX.PNJ02.049
PMDT4
300
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G64Mn
LX.PNJ02.054
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G32Mn
LX.PNJ02.041
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G50Mn
LX.PNJ02.052
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G32Mn
LX.PNJ0C.008
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z442G25Mn
LX.PNJ02.056
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
N
AS7715Z444G50Mn
LX.PNJ0C.005
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G50Mn
LX.PNJ02.053
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z443G32Mn
LX.PNJ0C.004
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z444G32Mn
LX.PNJ02.044
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G32Mn
LX.PNJ02.043
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z444G32Mn
LX.PNJ02.042
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z443G25Mn
LX.PNJ02.040
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mi
LX.PNJ02.039
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.038
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.037
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.036
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
Appendix A
172
VGA
Chip
Model
Acer Part No
CPU
LCD
AS7715Z443G25Mn
LX.PNJ02.035
PMDT4
400
NLED17.3
WXGA+G
UMA
AS7715Z443G25Mn
LX.PNJ02.034
PMDT4
400
NLED17.3
WXGA+G
AS7715Z443G25Mn
LX.PNJ02.033
PMDT4
400
AS7715Z443G25Mn
LX.PNJ02.032
AS7715Z443G25Mn
VRAM
1
Memory 1
Memory 2
N
SO2GBIII10
SO1GBIII10
UMA
N
SO2GBIII10
SO1GBIII10
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
LX.PNJ02.031
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.030
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.029
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.028
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.027
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.026
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.025
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.024
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.023
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.022
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.021
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.020
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.019
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.018
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.017
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.015
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.014
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.013
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.012
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.011
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
173
Appendix A
VGA
Chip
Model
Acer Part No
CPU
LCD
AS7715Z443G25Mn
LX.PNJ02.010
PMDT4
400
NLED17.3
WXGA+G
UMA
AS7715Z443G25Mn
LX.PNJ02.009
PMDT4
400
NLED17.3
WXGA+G
AS7715Z443G25Mn
LX.PNJ02.008
PMDT4
400
AS7715Z443G25Mn
LX.PNJ02.006
AS7715Z443G25Mn
VRAM
1
Memory 1
Memory 2
N
SO2GBIII10
SO1GBIII10
UMA
N
SO2GBIII10
SO1GBIII10
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
LX.PNJ02.007
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.005
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.004
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.003
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.002
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z443G25Mn
LX.PNJ02.001
PMDT4
400
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO1GBIII10
AS7715Z434G32Mn
S2.PNJ02.001
PMDT4
300
NLED17.3
WXGA+G
UMA
N
SO2GBIII10
SO2GBIII10
AS7715Z432G32Mi
S2.PL50C.001
PMDT4
300
NLED17.3
WXGA+G
UMA
N
SO2GBII6
N
AS7715Z432G16Mn
S2.PNK0C.001
PMDT4
300
NLED17.3
WXGA+G
UMA
N
SO1GBIII10
SO1GBIII10
Model
Acer Part No
AS7715Z433G25Mi
Memory
3
Memory
4
S2.PL40C.001
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.016
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.045
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.057
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z443G32Mn
LX.PNJ02.061
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z442G32Mn
LX.PNJ0C.007
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G50Mn
LX.PNJ02.070
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z443G32Mn
LX.PNJ02.062
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G64Mn
LX.PNJ02.065
N
N
N640GB
5.4KS
N
NSM8XS
N
Appendix A
HDD
1(GB)
HDD
2(GB)
ODD
Media
Processor
174
Memory
3
Memory
4
LX.PNJ02.069
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z444G50Mn
LX.PNJ02.068
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z444G25Mn
LX.PNJ02.067
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z444G25Mn
LX.PNJ02.066
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.059
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G64Mn
LX.PNJ02.064
N
N
N640GB
5.4KS
N
NSM8XS
N
AS7715Z444G64Mn
LX.PNJ02.063
N
N
N640GB
5.4KS
N
NSM8XS
N
AS7715Z443G32Mn
LX.PNJ02.060
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z442G32Mn
LX.PNJ02.058
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z434G50Mn
LX.PNJ02.050
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z434G32Mn
LX.PNJ02.049
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G64Mn
LX.PNJ02.054
N
N
N640GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.041
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G50Mn
LX.PNJ02.052
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ0C.008
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z442G25Mn
LX.PNJ02.056
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z444G50Mn
LX.PNJ0C.005
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z444G50Mn
LX.PNJ02.053
N
N
N500GB
5.4KS
N
NSM8XS
N
AS7715Z443G32Mn
LX.PNJ0C.004
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.044
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.043
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z444G32Mn
LX.PNJ02.042
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.040
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mi
LX.PNJ02.039
N
N
N250GB
5.4KS
N
NSM8XS
N
Model
Acer Part No
AS7715Z444G50Mn
175
HDD
1(GB)
HDD
2(GB)
ODD
Media
Processor
Appendix A
Memory
3
Memory
4
LX.PNJ02.038
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.037
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.036
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.035
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.034
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.033
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.032
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.031
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.030
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.029
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.028
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.027
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.026
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.025
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.024
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.023
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.022
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.021
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.020
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.019
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.018
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.017
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.015
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.014
N
N
N250GB
5.4KS
N
NSM8XS
N
Model
Acer Part No
AS7715Z443G25Mn
Appendix A
HDD
1(GB)
HDD
2(GB)
ODD
Media
Processor
176
Memory
3
Memory
4
LX.PNJ02.013
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.012
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.011
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.010
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.009
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.008
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.006
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.007
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.005
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.004
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.003
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.002
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z443G25Mn
LX.PNJ02.001
N
N
N250GB
5.4KS
N
NSM8XS
N
AS7715Z434G32Mn
S2.PNJ02.001
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z432G32Mi
S2.PL50C.001
N
N
N320GB
5.4KS
N
NSM8XS
N
AS7715Z432G16Mn
S2.PNK0C.001
N
N
N160GB
5.4KS
N
NSM8XS
N
Model
Acer Part No
AS7715Z433G25Mi
S2.PL40C.001
N
5 in 1-Build in
3rd WiFi BG
N
N
AS7715Z443G25Mn
LX.PNJ02.016
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ02.045
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ02.057
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G32Mn
LX.PNJ02.061
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z442G32Mn
LX.PNJ0C.007
N
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
Model
Acer Part No
AS7715Z443G25Mn
177
Extra
SW1
Card Reader
HDD
1(GB)
HDD
2(GB)
Wireless LAN1
ODD
Bluetooth
Media
Processor
VOIP
Phone
Appendix A
Model
Acer Part No
Extra
SW1
Card Reader
Wireless LAN1
AS7715Z444G50Mn
LX.PNJ02.070
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G32Mn
LX.PNJ02.062
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G64Mn
LX.PNJ02.065
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G50Mn
LX.PNJ02.069
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G50Mn
LX.PNJ02.068
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G25Mn
LX.PNJ02.067
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G25Mn
LX.PNJ02.066
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ02.059
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G64Mn
LX.PNJ02.064
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G64Mn
LX.PNJ02.063
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G32Mn
LX.PNJ02.060
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z442G32Mn
LX.PNJ02.058
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z434G50Mn
LX.PNJ02.050
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z434G32Mn
LX.PNJ02.049
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G64Mn
LX.PNJ02.054
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ02.041
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G50Mn
LX.PNJ02.052
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ0C.008
N
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z442G25Mn
LX.PNJ02.056
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G50Mn
LX.PNJ0C.005
N
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G50Mn
LX.PNJ02.053
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G32Mn
LX.PNJ0C.004
N
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ02.044
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z444G32Mn
LX.PNJ02.043
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
Appendix A
Bluetooth
VOIP
Phone
178
Model
Acer Part No
Extra
SW1
Card Reader
Wireless LAN1
AS7715Z444G32Mn
LX.PNJ02.042
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.040
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mi
LX.PNJ02.039
McAfee
5 in 1-Build in
3rd WiFi BG
N
N
AS7715Z443G25Mn
LX.PNJ02.038
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.037
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.036
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.035
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.034
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.033
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.032
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.031
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.030
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.029
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.028
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.027
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.026
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.025
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.024
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.023
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.022
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.021
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.020
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.019
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.018
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
179
Bluetooth
VOIP
Phone
Appendix A
Model
Acer Part No
Extra
SW1
Card Reader
Wireless LAN1
AS7715Z443G25Mn
LX.PNJ02.017
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.015
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.014
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.013
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.012
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.011
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.010
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.009
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.008
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.006
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.007
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.005
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.004
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.003
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.002
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z443G25Mn
LX.PNJ02.001
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z434G32Mn
S2.PNJ02.001
McAfee
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
AS7715Z432G32Mi
S2.PL50C.001
N
5 in 1-Build in
3rd WiFi BG
N
N
AS7715Z432G16Mn
S2.PNK0C.001
N
5 in 1-Build in
3rd WiFi 1x2 BGN
N
N
Appendix A
Bluetooth
VOIP
Phone
180
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® 7 environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Aspire 7715Z/7315
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
181
Microsoft® Windows® 7 Environment Test
Vendor
Description
Acer P/N
Adapter
DELTA
Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A,
LV5 LED LF
AP.06501.026
LITE-ON
Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650-22AC
LV5 LED LF
AP.06503.024
HIPRO
Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP-A0652R3B 1LF,
LV5 LED LF
AP.0650A.012
Realtek Audio Codec ALC272X
LZ.21000.045
SANYO
Battery SANYO AS-2009A Li-Ion 3S2P SANYO 6 cell 4400mAh
Main COMMON 2.2Ah(A)
BT.00603.076
SONY
Battery SONY AS-2009A Li-Ion 3S2P SONY 6 cell 4400mAh
Main COMMON 2.2Ah(G6F)
BT.00604.030
PANASONIC
Battery PANASONIC AS-2009A Li-Ion 3S2P PANASONIC 6 cell
4400mAh Main COMMON 2.2Ah(CG )
BT.00605.036
SAMSUNG
Battery SAMSUNG AS-2009A Li-Ion 3S2P SAMSUNG 6 cell
4400mAh Main COMMON 2.2Ah(F)
BT.00606.002
SIMPLO
Battery SIMPLO AS-2009A Li-Ion 3S2P PANASONIC 6 cell
4400mAh Main COMMON Panasonic 2.2Ah ( CG )
BT.00607.066
SIMPLO
Battery SIMPLO AS-2009A Li-Ion 3S2P LGC 6 cell 4400mAh
Main COMMON LGC 2.2Ah(S3 )
BT.00607.067
SIMPLO
Battery SIMPLO AS-2009A Li-Ion 3S2P SAMSUNG 6 cell
4400mAh Main COMMON SDI 2.2Ah(F)
BT.00607.068
Suyin
Suyin 0.3M DV Camellia_2G
AM.21400.045
Chicony
Chicony 0.3M DV Calla_2G
AM.21400.046
5 in 1-Build in MS, MS Pro, SD, SC, XD
CR.21500.013
INTEL
CPU Intel CeleronM T1600 1.66G 1M 667 Dual Core, MV
KC.16001.CMT
INTEL
CPU Intel CeleronM T1700 PGA 1.83G 1M 667 Dual Core, MV
KC.17001.CMT
INTEL
CPU Intel Celeron 585 PGA 2.16G 1M 667 MV
KC.N0001.585
INTEL
CPU Intel Celeron 575 PGA 2.0G 1M 667 MV
KC.N0001.575
INTEL
CPU Intel Celeron 900 PGA 2.2G 1M 800 35W
KC.N0001.900
INTEL
CPU Intel Pentium Dual-Core T3400 PGA 2.16G 1M 667 MV
KC.34001.DTP
INTEL
CPU Intel Pentium Dual-Core T4200 PGA 2.0G 1M 800 35W R-0
no VT
KC.42001.DTP
SEAGATE
HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS Crockett
SATA LF F/W:0303
KH.16001.034
TOSHIBA
HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX Libra SATA
LF F/W: FG011J
KH.16004.006
HGST
HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300 Falcon-B
SATA LF F/W:C40C
KH.16007.019
Audio Codec
Realtek
Battery
Camera
Card Reader
N/A
CPU/Processor
HDD
182
Appendix B
Vendor
Description
Acer P/N
WD
HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160
SATA LF F/W:11.01A11
KH.16008.022
SEAGATE
HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS Wyatt SATA
LF F/W:0001SDM1
KH.25001.016
TOSHIBA
HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX Libra SATA
LF F/W:FG001J
KH.25004.003
HGST
HDD HGST 2.5" 5400rpm 250GB HTS545025B9A300 Panther B
SATA LF F/W:C60F
KH.25007.015
WD
HDD WD 2.5" 5400rpm 250GB WD2500BEVT-22ZCT0 ML160
SATA LF F/W:11.01A11
KH.25008.021
SEAGATE
HDD SEAGATE 2.5" 5400rpm 320GB ST9320320AS Crockett
SATA LF F/W:0303
KH.32001.008
TOSHIBA
HDD TOSHIBA 2.5" 5400rpm 320GB MK3255GSX Libra SATA
LF F/W:FG011J
KH.32004.002
HGST
HDD HGST 2.5" 5400rpm 320GB HTS545032B9A300 Panther B
SATA LF F/W: C60F
KH.32007.007
WD
HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160
SATA LF F/W:11.01A11
KH.32008.013
SEAGATE
HDD SEAGATE 2.5" 5400rpm 500GB ST9500325AS Wyatt SATA
LF F/W:0001SDM1
KH.50001.011
HGST
HDD HGST 2.5" 5400rpm 500GB HTS545050B9A300 Panther B
SATA LF F/W:C60F
KH.50007.009
WD
HDD WD 2.5" 5400rpm 500GB WD5000BEVT-22ZAT0 ML250
SATA LF F/W:01.01A01
KH.50008.013
Keyboard eMACHINES EM-7T HM50/70 Internal 17 Standard
Black
KB.I170E.001
Keyboard
LAN
Atheros
Atheros AR8114 AR8114
NI.22400.040
Atheros
Atheros AR8132L
NI.22400.042
AUO
LED LCD AUO 17.3" WXGA+ Glare B173RW01-V0 LF 220nit
8ms 600:1
LK.17305.001
SAMSUNG
LED LCD SAMSUNG 17.3" WXGA+ Glare LTN173KT01-A01 LF
220nit 8ms 600:1
LK.17306.001
LPL
LED LCD LPL 17.3" WXGA+ Glare LP173WD1-TLA1 LF 220nit
8ms 600:1
LK.17308.001
CMO
LED LCD CMO 17.3" WXGA+ Glare N173O6-L02 LF 220nit 8ms
600:1
LK.1730D.001
NANYA
Memory NANYA SO-DIMM DDRII 667 1GB NT1GT64UH8D0FN3C LF 64*16 0.07um
KN.1GB03.026
MICRON
Memory MICRON SO-DIMM DDRII 667 1GB
MT8HTF12864HDY-667G1 LF 64*16 0.065um
KN.1GB04.010
ELPIDA
Memory ELPIDA SO-DIMM DDRII 667 1GB EBE11UE6ACUA6E-E LF 64*16 0.065um
KN.1GB09.008
SAMSUNG
Memory SAMSUNG SO-DIMM DDRII 667 1GB M470T2864EH3CE6 LF 64*16 0.055um
KN.1GB0B.027
LCD
Memory
Appendix B
183
Vendor
Description
Acer P/N
HYNIX
Memory HYNIX SO-DIMM DDRII 667 1GB HMP112S6EFR6C-Y5
LF 64*16 0.055um
KN.1GB0G.022
NANYA
Memory NANYA SO-DIMM DDRII 667 2GB NT2GT64U8HD0BN3C LF 128*8 0.07um
KN.2GB03.011
MICRON
Memory MICRON SO-DIMM DDRII 667 2GB MT16HTF25664HY667G1 LF 128*8 0.065um
KN.2GB04.010
ELPIDA
Memory ELPIDA SO-DIMM DDRII 667 2GB EBE21UE8ACUA6E-E LF 128*8 0.07um
KN.2GB09.001
SAMSUNG
Memory SAMSUNG SO-DIMM DDRII 667 2GB M470T5663EH3CE6 LF 128*8 0.055um
KN.2GB0B.011
HYNIX
Memory HYNIX SO-DIMM DDRII 667 2GB HMP125S6EFR8CY5 LF 128*8 0.055um
KN.2GB0G.012
HYNIX
Memory HYNIX SO-DIMM DDRII 667 1GB HYMP112S64CP6-Y5
LF
KN.1GB0G.012
HYNIX
Memory HYNIX SO-DIMM DDRII 667 2GB HYMP125S64CP8-Y5
LF
KN.2GB0G.004
Northbridge Chipset
INTEL
NB Chipset Intel CS GL40NB A1
KI.G4501.009
PANASONIC
ODD PANASONIC Super-Multi DRIVE 12.7mm Tray DL 8X
UJ880A LF W/O bezel SATA
KU.00807.064
HLDS
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X GT20N LF
W/O bezel SATA
KU.0080D.040
SONY
ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X AD-7580S
LF W/O bezel SATA
KU.0080E.017
PLDS
ODD PLDS Super-Multi DRIVE 12.7mm Tray DL 8X DS-8A3S LF
W/O bezel SATA
KU.0080F.004
ODD
Southbridge Chipset
INTEL
SB Chipset Intel CS ICH9M
KI.80101.030
Norton
Norton 360
SR.23900.005
Norton
Antivirus application NIS
SR.23900.002
UMA (Intel)
KI.23200.038
PIFA
LZ.23500.006
Foxconn
Foxconn FOX_ATH_XB63 Foxconn Atheros XB63 minicard b/g
NI.23600.007
Foxconn
Foxconn Wireless LAN Broadcom 4312 minicard b/g
NI.23600.029
Software
VGA Chip
N/A
Antenna
WNC
WLAN
184
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
•
Service guides for all models
•
User's manuals
•
Bios updates
•
Software utilities
•
Spare parts lists
•
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
•
Detailed information on Acer's International Traveler's Warranty (ITW)
•
Returned material authorization procedures
•
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
185
186
Appendix C
Index
A
Replacing
AFLASH Utility
33
100
D
Antennas
DIMM Modules
Removing 88
Replacing 91
Removing 51
Replacing 118
Display 3
B
display
Battery
hotkeys
121
Replacing
E
Battery Pack
Removing
46
EasyTouch Failure
BIOS
ROM type 14
vendor 14
Version 14
Flowchart
Features 1
Flash Utility
33
FPC Cable
Removing
86
FRU (Field Replaceable Unit) List
151
H
Hard Disk Drive
Board Layout
Removing 54
Replacing 116
145
brightness
hotkeys
45
F
21–33
Advanced 24
Boot 31
Exit 32
Navigating 21
Onboard Device Configuration 27
Power 29
Save and Exit 32
Security 26
System Security 32
134
External Module Disassembly
BIOS Utility
Top View
12
HDTV Switch Failure
12
135
Hibernation mode
C
12
Hot Keys 10
hotkey
Camera Module
Removing 83
Replacing 96
I
caps lock
Indicators 8
5, 8
Common Problems 124
Intermittent Problems 136
on indicator
129
Internal Speaker Failure 128
Internal Microphone Failure
computer
on indicator
5, 8
CPU
Removing 80
Replacing 99
CPU Fan
Removing
78
J
Jumper and Connector Locations
145
K
Keyboard
187
Removing 58
Replacing 115
num lock
on indicator 5,
Keyboard Failure 127
8
O
L
ODD Failure
LCD Bezel
131
Online Support Information
Removing 82
Replacing 97
185
Optical Disk Drive
Replacing
LCD Brackets
119
Optical Drive Module
Removing 86
Replacing 94
Removing
49
P
LCD Cable
94
LCD Failure 127
Replacing
Panel
Bottom
LCD Module
PC Card
Removing 59
Replacing 110
Power On Failure
91
124
R
LCD Panel
Removing 84
Replacing 94
Replacing
104, 105
Right Speaker Module
Left Speaker Module
Removing 70
Replacing 104
Removing 68
Replacing 105
RTC Battery
Lower Covers
Removing 48
Replacing 119
Removing
75
S
M
SD Dummy Card
Main Unit Disassembly
Flowchart
Removing 47
Replacing 120
56
104, 105
Removing 68, 70
Mainboard
Speakers
Removing 74
Replacing 101
Switch Cover
media access
on indicator
Removing 57
Replacing 116
5, 8
Memory
System
Removing 51
Replacing 118
124
Model Definition 164
Memory Check
Block Diagram
No Display Issue
125
3
T
Test Compatible Components
Thermal Module
N
188
8
Removing 67
Replacing 106
81
LCD Module Reassembly Procedure
7
Power Board
LCD Module Disassembly
Flowchart
4
Removing 76
Replacing 100
181
Thermal Unit Failure
134
TouchPad
Removing
72
TouchPad Bracket
Removing 72
Replacing 102
TouchPad Failure
128
Troubleshooting
Built-in KB Failure 127
EasyTouch Buttons 134
HDTV Switch 135
Internal Microphone 129
Internal Speakers 128
LCD Failure 127
No Display 125
ODD 131
Other Failures 135
Power On 124
Thermal Unit 134
TouchPad 128
WLAN 134
U
Undetermined Problems
136
Upper Cover
Removing 63
Replacing 106
utility
BIOS
21–33
W
Windows 2000 Environment Test 182
Wireless Function Failure
134
WLAN Module
Removing 52
Replacing 118
189
190