Technical information | Acer 8200 Laptop User Manual

Acer
TravelMate 8210/8200
Service Guide
Service guide files and updates are available
on the ACER/CSD web. For more
information, please refer to http://
csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates of notebook TravelMate 8210/8200 service guide.
Date
October 12, 2006
II
Chapter
Updates
first release
Copyright
Copyright© 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any
form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior
written permission of Acer Incorporated.
III
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose.
Any Acer Incorporated software described in this manual is sold or licensed “as is”. Should the programs prove
defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any
defect in the software.
Acer is a registered trademark of Acer Incorporated.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
IV
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information related to the
current topic.
WARNING
Alerts you to any damage that might result from doing or not
doing specific actions.
CAUTION
Gives precautionary measures to avoid possible hardware
or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the
accomplishment of procedures.
V
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's “global” product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on
card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic
service guide. In such cases, please contact your regional offices or the responsible personnel/channel to
provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on
your regional web or channel. For whatever reason, if a part number change is made, it will not be noted in the
printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the
list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
VI
Table of Contents
Chapter 1 System Specifications 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operating System . . . . . . . . . . . . . . . . . . . . . . . . . .
Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display and Graphics . . . . . . . . . . . . . . . . . . . . . . .
Storage Subsystem . . . . . . . . . . . . . . . . . . . . . . . .
I/O Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight and Dimensions . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
2
2
2
2
3
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 4
Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Open View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . .
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
7
8
8
9
Using the Keyboard . . . . . . . . . . . . . . . . . . . . 10
Lock keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Embedded Numeric Keypad . . . . . . . . . . . . . . . . .
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
11
11
13
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Easy-launch Buttons . . . . . . . . . . . . . . . . . . . . 15
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . . . . 16
Acer Empowering Technology . . . . . . . . . . . . 17
Acer eDataSecurity Management . . . . . . . . . . . . .
Acer eLock Management . . . . . . . . . . . . . . . . . . .
Acer ePerformance Management . . . . . . . . . . . . .
Acer eRecovery Management . . . . . . . . . . . . . . .
Acer eNet Management . . . . . . . . . . . . . . . . . . . .
Acer ePower Management . . . . . . . . . . . . . . . . . .
Acer ePresentation Management . . . . . . . . . . . . .
TOC
18
20
21
22
22
24
25
VIII
Acer OrbiCam . . . . . . . . . . . . . . . . . . . . . . . . . 26
Launching the Acer OrbiCam . . . . . . . . . . . . . . . .
Changing the Acer OrbiCam settings . . . . . . . . . .
Capturing photos or videos . . . . . . . . . . . . . . . . . .
Using the Acer OrbiCam as webcam . . . . . . . . . .
Enabling the Acer VisageON . . . . . . . . . . . . . . . .
27
27
29
29
29
Acer GraviSense . . . . . . . . . . . . . . . . . . . . . . 32
Using Acer GraviSense . . . . . . . . . . . . . . . . . . . . 32
Protecting the HDD . . . . . . . . . . . . . . . . . . . . . . . . 32
Anti-Theft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the System Utilities . . . . . . . . . . . . . . . . 34
Acer GridVista (dual-display compatible) . . . . . . . 34
Launch Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Hardware Specifications and Configurations . 36
Chapter 2 System Utilities 45
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . 45
Invoking BIOS Setup . . . . . . . . . . . . . . . . . . . . . . 45
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lid Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-Dim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
46
47
47
47
Information Menu . . . . . . . . . . . . . . . . . . . . . . 48
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . 51
Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . 52
Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Chapter 3 Machine Disassembly and Replacement 56
General Information . . . . . . . . . . . . . . . . . . . . 56
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . 56
Disassembly Procedure Flowchart . . . . . . . . . 57
Disassembly Procedure . . . . . . . . . . . . . . . . . 59
IX
TOC
Removing the Battery Pack . . . . . . . . . . . . . . . . .
Removing the HDD Module . . . . . . . . . . . . . . . . .
Removing the Memory and the MiniPCI Card . . .
Disassembling the Main Unit . . . . . . . . . . . . . . . .
Disassembling the LCD Module . . . . . . . . . . . . . .
Disassembling the ODD Module . . . . . . . . . . . . . .
Disassembling the CCD Module . . . . . . . . . . . . . .
Disassembling the HDD Module . . . . . . . . . . . . . .
59
59
60
61
67
69
70
70
Chapter 4 Troubleshooting 71
System Check Procedures . . . . . . . . . . . . . . . 72
External Diskette Drive Check . . . . . . . . . . . . . . .
External CD-ROM Drive Check . . . . . . . . . . . . . .
Keyboard or Auxiliary Input Device Check . . . . . .
Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power System Check . . . . . . . . . . . . . . . . . . . . . .
Check the Power Adaptor . . . . . . . . . . . . . . . . . . .
Check the Battery Pack . . . . . . . . . . . . . . . . . . . .
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . .
72
72
72
72
73
73
73
74
Power-On Self-Test (POST) Error Message . 75
Index of Error Messages . . . . . . . . . . . . . . . . . . . . 75
POST Code . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Index of Symptom-to-FRU Error Message . . . 79
Intermittent Problems . . . . . . . . . . . . . . . . . . . 82
Undetermined Problems . . . . . . . . . . . . . . . . . 83
Chapter 5 Jumper and Connector Locations 84
Top View of Main Board . . . . . . . . . . . . . . . . . 84
Part One of Top View . . . . . . . . . . . . . . . . . . . . . . 85
Part Two of Top View . . . . . . . . . . . . . . . . . . . . . . 85
Part Three of Top View . . . . . . . . . . . . . . . . . . . . . 86
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Part One of Bottom View . . . . . . . . . . . . . . . . . . . 87
Part Two of Bottom View . . . . . . . . . . . . . . . . . . . 88
Part Three of Bottom View . . . . . . . . . . . . . . . . . . 88
Chapter 6 FRU (Field Replaceable Unit) List 89
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . 90
TOC
X
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
XI
TOC
Chapter 1
System Specifications
Features
Operating System
•
Windows VistaTM Capable
•
Windows VistaTM Premium Ready
•
Genuine Windows® XP Professional x64 Edition
•
Genuine Windows® XP Professional (SP2)
•
Genuine Windows® XP Home Edition (SP2)
Platform
Intel® Centrino® Duo mobile technology, featuring:
•
Intel® CoreTM Duo processor T2300/ T2400/ T2500/ T2600 (2MB L2 cache, 1.66/ 1.83/ 2.0/ 2.16GHz, 667
MHz FSB) (for TravelMate 8200 series)
•
Intel® CoreTM 2 Duo processor T5500/ T5600 (2MB L2 cache, 1.66/ 1.83GHz, 667MHz FSB), or T7200/
T7400/ T7600 (4MB L2 cache, 2/ 2.16/ 2.33GHz, 667MHz) (for TravelMate 8210 series)
•
Intel® 945PM (Calistoga) Express Chipset with ICH7M-DH
System Memory
•
512MB/1GB or 2GB of DDR2 533/667MHz memory, upgradeable to 4GB using two soDIMM modules
(dual channel support)
Display and Graphics
•
15.4” WSXGA + TFT LCD, 1680 x 1050 pixel resolution, 16.7 million colors, simultaneous multi-window
viewing via Acer GridVistaTM support
•
ATI MobilityTM Radeon® X1600 with 256MB of GDDR3 VRAM, ATI POWERPLAYTM 5.0, Microsoft®
DirectX® 9.0 and PCI Express® support
•
Dual ViewTM support
•
Simultaneous LCD and CRT display, with LCD panel resolution at 70Hz refresh rate
•
Up to 2048 x 1536 resolution on non-interlaced CRT display
•
MPEG-2/DVD hardware-assisted capability
•
S-video/TV-out (NTSC/PAL) support
•
DVI-D (true digital video interface) support
Storage Subsystem
•
80/100/120/160GB SATA hard disk drive with Acer DASP (Disk Anti-Shock Protection)
•
Acer MediaBay for hot-swappable optical drive modules
•
•
8X DVD-Super Multi double layer
•
1X Blue-Ray drive
5-in-1 card reader, Secure Digital (SD), MultimediaCard (MMC), Memory Stick® (MS), Memory Stick
PROTM, (MS-PRO) and xD-Picture CardTM (xD)
Chapter 1
1
I/O Interface
•
124-pin Acer ezDock port
•
ExpressCardTM /34 slot
•
Four USB 2.0 ports
•
IEEE 1394 port
•
Ethernet (RJ-45) port
•
Modem (RJ-11) port
•
External display (VGA) port
•
S-video/TV-out (NTSC/PAL) port
•
DVI-D port
•
Microphone/line-in jack
•
Headphones/speaker/line-out with S/PDIF support
•
Fast infrared (FIR) port
•
PC Card slot (one Type II)
•
34 mm PCI Express Card slot
•
SmartCard slot
•
5-in-1 card reader (SD/MMC/MS/MS-Pro/xD-Picture CardTM)
•
DC-in jack for AC adaptor
Communication
•
Acer Video Conference featuring Acer Orbicam and optional Acer Bluetooth® VoIP phone
•
Acer Orbicam 1.3 megapixel CMOS camera (LCD panel-mounted) featuring:
•
225-degree ergonomic rotation
•
Acer VisageON technology
•
Acer PrimaLite technology
•
Modem: 56K ITU V.92 modem with PTT approval, Wake-on-Ring ready
•
LAN: Gigabit Ethernet, Intel® AMT (Active Management Technology) support; Wake-on-LAN support
•
WLAN: Integrated Intel® PRO/Wireless 3945 ABG network connection (dual-band tri-mode 802.11a/b/g)
Wi-Fi CERTIFIEDTM solution, Acer SignalUpTM wireless technology support
Power Subsystem
•
ACPI 2.0 CPU power management standard: Standby and Hibernation power-saving modes
•
87W 7800mAh 9-cell Li-Ion battery pack and optional 42W 3800mAh Li-Ion 2nd battery pack
•
Acer QuicChargeTM technology:
•
•
80% charge in 1 hour
•
2-hour rapid charge with system off
•
2.5-hour charge-in-use
Three-pin 90W AC adaptor
Audio
2
•
Intel® high-definition audio support
•
S/PDIF (Sony/Philips Digital Interface) support for digital sound system
•
Audio system with two built-in speakers (1.5W)
•
Built-in microphone
•
Sound Blaster® Pro and MS-Sound compatible
Chapter 1
Weight and Dimensions
•
3 kg (6.6 lbs.)
•
364 (W) x 271 (D) x 26.3/38 (H) mm (14.33 x 10.66 x 1.03/1.49 inches)
Chapter 1
3
Block Diagram
DVI
TVOUT
P25
P25
TFT LCD Panel
15.4"
WSXGA+
P25
P26
P29
Camera Module(1.3M)
USB7
P25
USB6
Bluetooth
CRT
X'TAL
6M
6 in 1 Cardreader
(SMSC 2228) P31
USB4
P29
USB Port x 4
USB0~3
P37
Audio Amplifier
Maxim Max 9750
Speaker
P37
DVI
X'TAL
27M
X'TAL
14.318MHZ
P2
SATA
P18,P19,P20,P21,
P22,P24
VGA
ATI M56P
P23
VRAM X 4(GDDR3)
256MB/500MHZ
ICS954310BGLF
Clock Generator
TVout
LVDS
VGA
HDD
P35
652 BGA
LPC
P14,P15,P16,P17
SMBUS
P35
G-SENSOR
X'TAL
32.768K
BIOS
G sensor
P3,P4
CPU
P38
FIR
P5
(Option)
P38
TPM 1.2
Smart card
P30,P31
O2 711MP1
PCMCIA+1394
+Cardreader
Controller
X'TAL24.576MHZ
P12,P13
DDR II
SODIMM1
DDR II
SODIMM0
Thermal Sensor
Dual Channel DDR2
533/667 Mhz
PCI-Express
PCI Bus interface
OSC
48MHZ
P31
IEEE 1394
Port
P38
Super I/O
NS PC87383
P35
P40
Touch Pad
(Dual-Point)
P39
P39
KBC PC97551
X'TAL
32.768KHZ
ICH7-M Digital Home
DMI X4 interface
P6,P7,P8,P9,P10,P11
CALISTOGA-945PM
1466
FCBGA
533/667 MHZ FSB
Yonah/Merom 479
uFCPGA
ZC1 SYSTEM BLOCK DIAGRAM
PCI-Express
16X Lan
P36
Azalia
USB 2.0
P36
P37
Azalia MDC
Line in
Azalia Audio
Controller
Realtek ALC883
P37
Int MIC
Media-Bay
ODD/2nd HDD/2nd Battery
P35
P37
MIC Jack
Phone Jack
P37
P28
RJ11
Switch
Rev
1A
P28
RJ45
P25,P28
MAX4892
Switch
P37
P25,26
TV out / CRT
Switch
10/100/1G
DVI
Audio
PCI-Express X 2
EV@: Stuff when external VGA used
SH@: Stuff when SATA HDD used
PH@: Stuff when PATA HDD used
EZ4 Docking
Connector
PCIE1~2 , Lan
Ser & Par Port
PS2 , VGA, DVI
SPDIF,SM BUS
P32
USB5
P33
New Card
X'TAL
25M
P27
P45,P46
Primary Battery
Secod Battery
P5
Fan Header
P28
Transformer
P30
BLOCK DIAGRAM
Document Number
PCMCIA Slot
P27
SPI FLASH
82573E
Intel Tekoa
GigaLAN
P29
MiniCard /
WLAN
P30
Size
Chapter 1
4
Just for Starters...
Outlook View
Open View
#
#
Item
Item
Description
Description
1
Display screen
Displays computer output, also called Liquid-Crystal Display (LCD).
2
Microphone
Serves as an internal microphone for sound recording.
3
Palmrest
Serves to support your palms and wrists when you use the computer.
4
Camera
Captures photos and videos.
5
Easy-launch buttons
Buttons for launching frequently used programs.
6
Power button
Turns"Easy-launch
on and turnsbuttons"
off the computer.
on page 24
7
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the status of the
computer's functions and components.
8
Keyboard
Serves to key in the data.
9
Touchpad
Touch-sensitive pointing device which functions like a computer
mouse.
10
Click buttons (left,
center and right)
The left and right buttons function like the left and right mouse buttons;
the center button serves as a four-way scroll button.
Chapter 1
5
#
Item
Description
"Easy-launch buttons" on page 10
Closed
FrontItem
View
# Icon
Description
"Easy-launch buttons" on page 10
"Launch keys" on page 10
#
Item
##
Item
Icon
#
Description
Item
Icon
#
N/A
2
N/A
3#
Description
#
5
#
Item
Icon
Description
Speakers
Left and right speakers deliver stereo audio output.
Latch
Locks and releases the LCD panel.
Icon
Item
Description
"Launch keys" on page 10
Power indicator
Description Lights up when the computer is on.
Item
#
#
Description
Item
Icon
1
4
Description
Item
Description
Battery indicator
Icon
Item
Icon
Item
5-in-1 card reader
"Launch
#
Icon
#
Icon
Description
Accepts
Memory Stick (MS), Memory Stick Pro (MSPro),
MultiMediaCard
keys" on page 10 (MMC), Secure Digital (SD) and
xD-Picture Card (xD). Only one card can operate at any
given time.
Description
Note:
Description
6
Line-in jack
Accepts audio line-in devices (e.g., audio CD player,
stereo walkman).
7
Microphone jack
Accepts inputs from an external microphones.
8
Headphones/speaker/
line-out jack with S/
PDIF support
Connects to audio line-out devices (e.g., speakers,
headphones).
9
Bluetooth
communication button/
indicator
Slide to enable/disable Bluetooth function. Lights to
indicate the status of Bluetooth communications.
(optional)
Wireless
Slide to enable/disable Wireless function. Lights to
Description
indicate
the status of wireless LAN communications.
Description
(optional)
10
##
6
Item
Item
Indicates the computer’s battery status.
Description
Icon
Icon
Item
communications
Item
button/indicator
11
Four-pin IEEE 1394
port
Connects to IEEE 1394 devices.
12
Infrared port
Interfaces with infrared devices (e.g., infrared printer
and IR-aware computer).
Chapter 1
#
Icon
#
Item
Icon
Description
Item
Description
Left View
Note:
#
#
Icon
Icon
1
Item
Description
Item
Kensington lock slot
##
Icon
Icon
Description
Connects to a Kensington-compatible computer security
lock.
DescriptionDescription
Item
Item
2
Two USB 2.0 ports
Connect to USB 2.0 devices (e.g., USB mouse, USB
camera).
3
Modem (RJ-11) port
Connects to a phone line.
Note:
4
N/A
Optical disk drive
Accepts CDs or DVDs, depending on the optical disk
type.
5
N/A
Optical disk access
indicator
Lights up when the optical disk drive is active.
6
N/A
Optical disk drive eject
button
Ejects the optical disk from the drive.
7
N/A
Emergency eject hole
Ejects the optical drive tray when the computer is turned
off.
8
N/A
ExpressCard /34 slot
Accepts a 34 mm PCI Express Card.
PC Card slot
Accepts one Type II PC Card
PC Card slot eject
button
Ejects the PC Card from the slot.
9
10
N/A
#
Icon
Item
#
Icon
Item
Chapter 1
Description
Description
7
#
Icon
Item
Description
Right View
Note:
#
##
1
Icon
IconIcon
#
Icon
Item
#
Icon
Item
3#
Icon
N/A
Description
ItemItem
Description
Description
Note:
Description
Accepts the TravelMate SmartCard.
Icon
SmartCardItem
slot
#
2
Item
Two USB 2.0 ports
Description
Description
ItemVentilation slots
Connect to USB 2.0 devices (e.g., USB mouse, USB
camera).
Note:
Description
Keep the computer cool.
4
Ethernet (RJ-45) port
Connects to an Ethernet 10/100/1000-based network
(for selected model).
5
External display (VGA)
port
Connects to an external display device (e.g., external
monitor, LCD projector).
Rear View
#
#
#
##
#
Icon
Item
Icon
Description
Item
Icon
Description
Item
Description
Icon
Item
IconIconItem
1
Description
Item Description
Description
DVI-D
port
Supports digital video connections.
Icon
Item
Description
Note:
#
2
#
Icon
124-pin port (Replicator Connects to Acer ezDock.
Item connector)
Description
3#
Icon
Connects to a television or display device with S-video
Item S-video port/TV-out
Description
4
N/A
5
port
input.
Battery
Powers the computer.
DC-in jack
Connects to an AC adapter.
Note:
8
Chapter 1
Bottom View
#
# Item
Item
Description
Description
1
Battery lock
Locks the battery in position.
2
Battery bay
Houses the computer’s battery pack.
3
Battery release latch
Releases the battery for removal.
4
Optical drive bay
release latch
Releases the optical drive for removal.
5
Optical drive bay
Houses the computer’s optical drive.
6
Hard disk bay
Houses the computer's hard disk.
7
Acer DASP (disk AntiShock Protection)
Protects the hard disk drive from shocks and bumps.
8
Wireless LAN and
memory compartments
Houses the computer's Wireless LAN and main memory.
9
Ventilation slots and
cooling fan
Keep the computer cool. Do not cover or obstruct the opening of the
fan.
Note
Chapter 1
9
Using the Keyboard
The full-sized keyboard includes an embedded numeric keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock keys
The keyboard has three lock keys, each with its own status indicator.
Lock key
Description
Lock Key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters are typed in
uppercase.
<Fn> + <F11>
Num Lock
<Fn> + <F11>
When Num Lock is on, the embedded keyboard is in numeric
mode.
Scroll Lock
<Fn> + <F12>
When Scroll Lock is on, the screen moves one line up or down
when you press the up or down arrow keys respectively. scroll
Lock does not work with some applications.
<Fn> + <F12>
Embedded Numeric Keypad
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the right part of the keycaps.
Desired access
Num Lock on
Num Lock off
<Shift>
<Fn>
<Fn>
Lock key
Desired access
Description
Num Lock on
Num Lock off
Number keys on
embedded keypad
Type numbers in a normal
manner.
N/A
<Fn> keys
+ <F11>
Cursor-control
on
embedded keypad
Hold <Shift> while using
cursor-control keys.
Hold <Fn> while using cursorcontrol keys.
Main keyboard keys
Hold <Fn> while typing letters
on embedded keypad.
Type the letters in a normal
manner.
<Fn> + <F12>
10
Chapter 1
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Key
Key
Description
Icon
Windows key
Description
This key has the same effect as clicking on the Windows Start button. It
launches the Start menu. It can also be used with other keys to provide
a variety of functions:
+ Tab: Activates the next Taskbar button.
+ E: Opens the My Computer window.
Key
Description
<
> + <Tab>:
<
> + <E>:
<
> + <F1>:
<
> + <F>:
+ F1: Opens Help and Support.
+ F: Opens the Find (All Files dialog box).
<
> + <Tab>:
<
> + <E>:
<
> + <F1>:
<
> + <F>:
+ R: Opens the Run dialog box.
+ M: Minimizes all windows.
Shift +
<
+ <R>:
+ M)
> + <M>:
action.
<Shift> + <
Application key
+ <R>:
+ M: Undoes the minimize all windows (
> + <M>:
<
> + <M>:
This key has the same effect as clicking the right mouse button. It
opens the application’s context menu.
<Shift> + <
> + <M>:
Hotkeys
The computer employs hotkeys or key combinations to access most of the computer's controls like screen
brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before pressing
the other key in the hotkey combination.
<Fn>
Hotkey
Hotkey
Hotkey
Hot+Key
<Fn>
<F1>
<Fn> <Fn>
+ <F1>
<F1>
<Fn>
++<F1>
<Fn> + <F2>
<Fn> ++<F2>
<Fn>
<F2>
<Fn> + <F2>
<Fn>++<F3>
<F3>
<Fn>
<Fn> + <F3>
Icon
Icon
Icon
Function
Description
Function Description
Description
Function
Icon
Function
Hot key help
<Fn>
Description
Displays help on hot keys.
Acer eSetting
Launches
the Acer
eSetting on
in the Acer
"Acer
eManager"
Empowering
Technology.
page 20
"Acer eManager" on
page 20
Acer ePower
Management
"Acer eManager" on
Launches the Acer ePower Management in the
page
20 Technology.
Acer
Empowering
<Fn> +
<F3>
<Fn>
+ <F4>
<Fn> + <F4>
Chapter 1
<Fn> + <F5>
11
<Fn>
+ +<F4>
<Fn>
++<F3>
<F3>
<Fn>
<Fn>
<F4>
page 20
<Fn> + <F3>
"Acer eManager" on
page 20
<Fn>
+++<F4>
<Fn>
+<F5>
<F3>
<Fn>
<F3>
<Fn>
<Fn> + <F4>
<Fn> ++ <F4>
<F5>
<Fn>
<Fn>
Key
<Fn>+Hot
+<F5>
<F4>
<Fn>
+ +<F4>
<Fn>
<Fn>
+<F4>
<F4>
<Fn>
+ <F5>
<Fn>
+ <F5>
Icon
Function
Description
Sleep
Leads the computer to Sleep mode.
Display toggle
Switches the display output between the display
screen, external monitor (if connected) and both.
Screen blank
Turns off the display screen backlight to save
power. Press any key to return.
Touchpad toggle
Turns the internal touchpad on and off.
Speaker toggle
Turns the speakers on and off.
Volume up
Increases the sound volume.
Volume down
Decreases the sound volume.
Brightness up
Increases the screen brightness.
Brightness down
Decreases the screen brightness.
<Fn>++<F6>
<F5>
<Fn>
<Fn>
<F6>
<Fn>
+
<Fn>
+ +<F5>
<F5>
<Fn>
<Fn>+ +<F5>
<F5>
<Fn> + <F6>
<Fn> + <F6>
<Fn>
+<F7>
<F6>
<Fn>
<Fn>
+++<F6>
<Fn>
++
<F6>
<Fn>
<F7>
<Fn>
<F6>
<Fn> + <F6>
<Fn>
<F6>
<Fn>
<F7>
<Fn>
<F7>
<Fn>
<F7>
<Fn>
+ ++<F7>
<Fn>
++++<F7>
<F8>
<Fn>
<Fn>
<F8>
<Fn> + <F7>
<Fn>+++<F8>
<F7>
<Fn>
<F8>
<Fn>
<Fn>
<F8>
<Fn> + <F8>
<Fn>
<Fn>
++<F7>
<< >>
<Fn>
<Fn>
+ +<F8>
<Fn> + <F8>
<Fn>
+<+<<
<K<F8>
<Fn>
++
>
>>
<Fn>
<Fn>
<Fn>
+
>
<Fn>
<Fn>++ <F8>
< >
<Fn> + < >
<Fn>
+
>>>
<Fn>
+<<L>
<Fn>
<Fn>
++<
<
<Fn>+
<Fn>
++<< >>
<Fn>
< >
<Fn>
+< >
<Fn>
<Fn> ++<<J>>
<Fn>++<<
<Fn>
>
>
<Fn>
<Fn>++<< >>
<Fn>
+ <>
<Fn>
+
<Fn>
+<
<
>>
<Fn> + <
>
<Fn>
<Fn>+++<
<<I>>
<Fn>
<Fn>
<Fn>
++<< >>>
<Fn>
<Fn>++<< >
>
<Fn> +
+<
< >>
<Fn>
<Fn>
+< >
>
<Fn>
+<
<Fn> + < >
<Fn> + <
<Fn> + <
12
>
>
Chapter 1
Special keys
You can locate the Euro symbol and the US dollar sign on the upper center or bottom right side of the keyboard.
The Euro Symbol
1. Open a text editor or word processor.
Euro>
2. Either directly press the <Euro>
key on the bottom right<5>
side of the keyboard, or hold <Alt Gr> key then press
Alt Gr>
the Euro symbol on the number <5> key.
Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm Note
for more information.
www.microsoft.com/typography/faq/faq12.htm
The US Dollar Sign
1. Open a text editor or word processor.
2. Either directly press the <$> key on the bottom right side of the keyboard, or hold <Shift> and then press the
US dollar sign on the number <4> key.
<Dollar>
Note: This function varies according
settings.
<Shift> to the language <4>
Note:
Chapter 1
13
#
Item
Description
Indicators
#
Item
Description
The computer provides an array of three
indicatorskeys"
locatedon
above
the keyboard,
in addition to four indicators on
"Launch
page
10
the front cover. These indicators show the status of the computer and its components.
"Launch keys" on page 10
"Launch keys" on page 10
#
Item
Description
"Launch keys" on page 10
The power, battery, Bluetooth and wireless communication status indicators are on even when the LCD panel is
closed.
Icon
Icon
#
#
#
Icon
Item
Icon
Item
Icon
#
Function
Icon
Item
Caps Lock
Item
Num Lock
Item
Description
Media activity
Description
Description
Lights when Caps Lock is activated.
Description
Description
Lights when Num
Lock is activated.
Description
Glitters when the hard disk or optical drive is active.
Power
Lights when the computer is on.
Battery
Lights when the battery is being charged.
Bluetooth
Indicates the status of Bluetooth communication
1. Charging:
2. Fully charged:
Wireless LAN
14
Indicates the status of wireless LAN communication
Chapter 1
Easy-launch Buttons
"Acer
There are four buttons located above the keyboard. These buttons are called easy-launch
buttons. They are one
Empowering Technology" on page 1
user-programmable button, web browser button, mail button, and Acer Empowering Key
. Press
to run the
Acer Empowering Technology. Although the mail and web browser buttons are pre-set to E-mail and Internet
programs, they can be"Launch
redefined
by users.
set46
the web browser, mail and programmable buttons, run the Acer
Manager"
onTo
page
Launch Manager.
Easy launch button
Easy-launch button
Default application
Default application
Acer Empowering Technology (user-programmable)
"Easy-launch
buttons"
"Easy-launch buttons"
on page
10 on page 10
Mail
E-mail application (user-programmable)
Web browser
Internet browser (user-programmable)
P
User-programmable
"Easy-launch buttons" on page 10
Chapter 1
15
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds
as you move your finger across the surface of the touchpad. The central location on the palmrest provides
optimum comfort and support.
Touchpad Basics
Use the touchpad as follows:
•
•
•
(2)
Move your finger across
the
touchpad
(2)
to
move
the
cursor.
(1)
(4)
Press the left (1) and right (4) buttons located on the edge of the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the
touchpad (2) is the same as clicking the left button.
(3) to scroll up or down and move left or right a page. This button mimics
Use the four-way scroll (3) button
your cursor pressing on the right scroll bar of windows applications.
Function
Left button (1)
Right button (4)
Main touchpad (2)
Execute
Quickly click twice.
Select
Click once
Tap once
Drag
Click and hold.
Then slide your
finger across the
touchpad to drag
the cursor over the
selection.
Tap twice (at the
same speed as
double-clicking a
mouse button); rest
your finger on the
touchpad on the
second tap and
drag the cursor.
Access
context menu
Scroll
Center button (3)
Tap twice (at the
same speed as
double-clicking a
mouse button).
Click once
Click and hold to
move up/down/left/
right.
Note: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to
your finger movements: the lighter the touch, the better the response. Tapping hard will not increase the
touchpad’s responsiveness.
16
Chapter 1
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy to have access to the frequently used functions and
manage the notebook. It features the following handy utilities:
•
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
•
Acer eLock Management limits access to external storage media.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry setting.
•
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eSettings Management accesses system information and adjusts settings easily.
•
Acer eNet Management hooks up to location-based networks intelligently.
•
Acer ePower Management extends battery power via versatile usage profiles.
•
Acer ePresentation Management connects to a projector and adjusts dispaly settings conveniently.
For more information, press the
key to launch the Empowering Technology menu, then click on the appropriate
utility and select the Help function.
Chapter 1
17
Acer eDataSecurity Management
Acer eDataSecurity Management is a handy file encryption utility that protects the files from being accessed by
unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for quick and easy
data encryption and decryption and also supports on-the-fly file encryption for MSN Messenger and Microsoft
Outlook.
There are two passwords that can be used to encrypt and decrypt a file: the supervisor password and the filespecific password. The supervisor password is a “master” password that can decrypt any file on the system. The
file-specific password is assigned when you encrypt each individual file.
Acer eDataSecurity Management setup wizard will prompt for a supervisor password and default file-specific
password. This file-specific password will be used to encrypt files by default, or you can choose to enter your own
file-specific password when encrypting a file.
Note: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt the encrypted files! Be sure to safeguard all related password.
18
Chapter 1
Chapter 1
19
Acer eLock Management
Acer eLock Management is a security utility that allow you to lock up your removable data, optical and floppy
drives to ensure that data can not be stolen while your notebook is unattended.
•
Removable data devices: includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
•
Optical drive devices: includes any kind of CD-ROM or DVD-ROM drives.
•
Floppy disk drives: 3.5-inch disks only.
To activate Acer eLock Management, a password must be set at first. Once set, you may apply locks to any of the
three kinds of devices. The lock(s) will be set without any reboot necessary, and will remain locked after rebooting,
until unlocked.
If you do not set a password, Acer eLock Management will reset back to the initial status with all locks cancelled.
Note: If you lose the password, there is no method to reset it except by reformatting the notebook or
taking the notebook to an Acer Customer Service Center. Be sure to remember or write down the
password.
20
Chapter 1
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of the Acer notebook.
It provides you with the following options to enhance overall system performance:
•
Memory optimization: releases unused memory and checks memory usage.
•
Disk optimization: removes unneeded items and files.
•
Speed optimization: improves the usability and performance of the Windows XP system.
Chapter 1
21
Acer eRecovery Management
Acer eRecovery Management is a powerful utility with the need for recovery disks provided by the manufacturer.
The Acer eRecovery Management utility occupies space in a hidden partition on the system’s HDD. User-created
backups are stored on D:\ drive. Acer eRecovery Management provides:
•
Password protection
•
Recovery of applications and drives
•
Image or data backup:
•
•
Backup to HDD (set recovery point)
•
Backup to CD or DVD
Image or data recovery tools:
•
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent user-defined recovery point)
•
Recovery from CD or DVD
Note: If the computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To ensure the
best results when recovering the system using a CD or Acer eRecovery Management, detach all peripherals
(except external Acer ODD, if equipped), including the Acer ezDock.
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a variety of
locations. To access this utility, either click on the “Acer eNet Management” icon on the notebook, or start the
program from the Start menu. You also have the option to set Acer eNet Management to start automatically when
you boot up the PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the freedom
to manually adjust the settings to match your needs, simply by right clicking on the icon in the task bar.
22
Chapter 1
Acer eNet Management can save network settings for a location to a profile, and automatically apply the
appropriate profile when you move from one location to another. The settings stored include network connection
settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings. The security and safety
concerns mean that Acer eNet Management does not store username and password information.
Chapter 1
23
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface, or double click the Acer ePower Management icon in the
task tray.
AC Mode
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other settings, or
click on buttons to turn the following functions on or off: Wireless LAN, Bluetooth, CardBus, Memory Card, Audio,
and Wired LAN.
DC Mode
To suit your usage, there are four pre-defined profiles: Entertainment, Presentation, Word Processing, and
Maximum Battery. Or, you can define up to three of your own profiles.
Battery Status
For real-time battery life estimates based on current usage, refer to the panel on the lower left side of the window.
You can also click Advanced settings to:
24
•
Set alarms.
•
Reload factory defaults.
•
Select what actions will be taken when the cover is closed, and set passwords for accessing to the system
after Hibernation or Stand-by.
•
View information about Acer ePower Management.
Chapter 1
Acer ePresentation Management
Acer ePresentation Management lets you select from two of the most common projector resolution: XGA and
SVGA.
Chapter 1
25
Acer OrbiCam
The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The
camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the
back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that you can
transmit the best video quality over an instant messenger service.
Getting to Know Your Acer OrbiCam
1
#
23
Item
#
#
Item
Item
1
Lens
2
Power indicator
3
Rubber grip (selected models only)
Rotating the Acer Orbicam
The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the illustrations
below:
For your convenience, the camera snaps 45 degrees to match the position of your face in front in back of the LCD
panel.
Note: Do not rotate the camera clockwise to prevent it from the damage.
26
Chapter 1
Launching the Acer OrbiCam
To launch the Acer OrbiCam, double click on the Acer OrbiCam icon on the screen or Click Start > All programs
> Acer > Acer OrbiCam. The Acer OrbiCam capture windows window will appear as below:
Changing the Acer OrbiCam settings
Resolution
To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window,
then select the desired resolution. Setting the camera resolution to 640 x 480 or larger does not change the
capture window size.
Chapter 1
27
Options
Click Options to display Options
the Window, Preview,Window,
and Folder
tabs. UseFolder
the options to change the capture window
Preview
size, preview settings, and the folder for captured photos or videos.
Camera Settings
•
Basic settings: Click the Camera Settings icon on the bottom right corner of the capture display, then
select Camera Settings from the pop-up menu. You can adjust the Video, Audio, and Zoom/Face tracking
options from this window.
Camera Settings
Video, Audio
Video, Audio
•
Camera Settings
Zoom/Face tracking
Zoom/Face tracking
Capture settings: From the Camera Settings window, click the Driver Settings button. The Properties
Driver Settings
window will appear.
Driver Settings
Properties
Properties
Device Settings
Device Settings
28
Advanced Settings
Advanced Settings
Chapter 1
•
Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness,
etc.
•
Advanced Settings allows you to achieve gain control, implement image mirror, select image
enhancements and anti-flicker settings, and turn on/off the camera indicator.
•
Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature on
or off.
Capturing photos or videos
To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a Picture
or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player automatically
launches to display or play a preview of the photo/video clip.
Note: By default, all photos and videos are saved in the My Pictures and My Videos folder.
Using the Acer OrbiCam as webcam
The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application. To
use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can now
broadcast from your location to an IM partner anywhere in the world.
Enabling the Acer VisageON
The Acer VisageON technology comes with two features: Face tracking and Video effects (selected models only).
The Face Tracking feature tracks your head movement and automatically centers your face in the capture window.
The video effects feature allows you to select and apply an effect to your video transmissions.
Note: The face tracking feature is not capable of centering your face beyond the capture window frame.
Minimal head movements are tracked more efficiently.
To enable the Acer VisageON:
1. Right click on this icon, then select VisageON from the pop-up menu.
VisageON
VisageON
The VisageON window appears as below:
Chapter 1
29
2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings
and options in the right section.
Using the face tracking feature
To use the face tracking feature:
1. Click the left icon down arrow button, then select Single User or MultipleSingle
UsersUser
from theMultiple
pop-up menu. For
Users
multiple users, the face tracking feature automatically centers all the users’ face in the capture window,
otherwise the utility centers the face of the user closest to the camera.
2. Click the right icon to zoom in/out or reset the current view.
VisageON
3. Click VisageON to display
a menu that allows to change the configuration of the camera, face tracking and
VisageON
VisageON
video effects settings.
Using
video
effects
Using video
effects
(selected
Using
video
effects models only)
Using video effects
The Video SettingsVideo
section
allows you to select an avatar or accessory video effect from the list. To select an
Settings
Video
Settings
Video Settings
effect:
1. Click the encircled icon to display the available video effects. The Video Effect Selection
window appears as
Video
Video
below:
Video
Effect
EffectSelection
Selection
Effect Selection
30
Chapter 1
2. Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window.
Note: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow screen
instructions in the VisageON to continue.
Note: You may use video effects when using the camera for IM chat/video sessions or call conferences.
Chapter 1
31
Acer GraviSense
Acer GraviSense is an innovative utility designed to further protect your data by automatically moving the read/
write heads of the Acer notebook’s hard disk away from the storage disk (this is known as “parking” the heads) in
the event that sudden shock is detected. Acer GraviSense can also be set to activate an alarm in case the
notebook is moved by an unauthorized person.
Using Acer GraviSense
Start > (All) Programs > Acer GraviSense.
You can launch Acer GraviSense in a number of ways:
•
Start>>All
(All)
Programs>>Acer
Acer GraviSense
GraviSense.
From the Start menu, go to Start
programs
•
When Acer GraviSense is running, an icon
will display in the task tray. Move the cursor on the icon to
identify Acer GraviSense. Left click or right click on the icon to open a context menu.
Protecting the HDD
Right click on the tray icon to activate this feature and select HDD protection.
This function will park the HDD heads in the event that any sudden vibration or movement which exceeds the level
tolerated by the HDD is detected.
Anti-Theft
Right click on the tray icon to activate this feature and select Anti-Theft.
When enabled, this feature will sound an alarm if the notebook is moved. This feature is password-protected to
prevent unauthorized access.
Your password needs to be between four and eight characters, and should consist of letters and numbers. Once
you’ve set the password, the Anti-theft feature will be activated.
If you enter a password that is invalid for any reason, you will be prompted to try again.
32
Chapter 1
When this function is activated, Acer GraviSense will show a full screen image and a password window.
When Anti-Theft is activated, it will disable the following keys functions:
•
Alt + Tab
•
Ctrl +Shift + Esc
•
Ctrl + Alt + Del
•
Windows keys
•
Task bar
Besides, the settings below will be changed to “do nothing” (the personal settings will be recovered once the AntiTheft function is disable):
•
Power button
•
Sleep button
•
Close the lid
If the system detects any movement when this function is activated, the system will emit a beep as a warning and
prompt you to enter the password.
Note: Please remember the password for it can not be changed.
Note: You need to disable the Task Manager before setting the Anti-Theft function.
Chapter 1
33
Note:
Using the System Utilities
Note: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
Note: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure
thatControl
the second
monitor
is connected, then select
Start
Panel
Display
Note:
Start, Control Panel, Display and
click on Settings. Select the secondary monitor (2) icon in the display box and
Settings
(2)
then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new
Extend
my
windows
desktop
onto this monitor
settings and click OK to complete the process.
Apply
OK
Settings
Apply
Start Control Panel Display
(2)
Extend my windows desktop onto this monitor
OK
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on
the same screen. To access
please go to Start > All
Programs
and click on Acer GridVista. You may
Startthis
Allfunction,
Programs
Acer
GridVista
Startsettings
All Programs
choose any one of the four display
indicated below: Acer GridVista
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer GridVista is
simple to set up:
1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
34
Chapter 1
Note: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
Note:
recommended value.
Note:
Launch Manager
Launch Manager allows you"Easy-launch
to set the four buttons"
easy-launch
above the keyboard. You can access the
onbuttons
page located
24
Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
"Easy-launch buttons" on page 24
Start All Programs
Launch Manager
Start All Programs
Launch Manager
Chapter 1
35
Hardware Specifications and Configurations
Item
T7600
T7200
T5600
T5500
CPU speed (GHz)
2.33
2.16
2
1.83
1.66
Bus speed (MHz)
667
667
667
667
667
Bus/Core Ratio
14
13
12
11
10
L2 cache size (MB)
4
4
4
2
2
L2 cache speed (GHz)
2.33
2.16
2
1.83
1.66
Package type (pin)
479/478
479/478
479/478
479/478
479/478
Manufacturing technology (nm)
65
65
65
65
65
Thermal design power
34W
34W
34W
34W
34W
Thermal specification ( C)
100
100
100
100
100
Core voltage (V)
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
o
Item
T2700
T2600
T2500
T2400
T2300
CPU speed (GHz)
2.33
2.16
2
1.83
1.66
Bus speed (MHz)
667
667
667
667
667
Bus/Core Ratio
13
13
12
11
10
L2 cache size (MB)
2
2
2
2
2
L2 cache speed (GHz)
2.33
2.16
2
1.83
1.66
Package type (pin)
478
478
479/478
478
478
Manufacturing technology (nm)
65
65
65
65
65
Thermal design power
31W
31W
31W
31W
31W
Thermal specification ( C)
100
100
100
100
100
Core voltage (V)
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
o
Item
Specification
Package
Micro-FCBGA 1466-pin
Power
1.05V (core), 1.5V, VCCSM (DDR2 = 1.8V), 2.5V, 3.3V
Feature
• Processor host bus support
• Integrated SDRAM controller up to 4GB (2 SODIMM support)
Integrated SDRAM clock buffer to support 2 SODIMM
• External Graphics interface for PCI Express Architecture support
• DMI x 2 and DMI x 4 for connection between GMCH and ICH7M
Item
36
T7400
Specification
Package
BGA 652-pin
Power
1.05V (core), 1.5V, 3.3V, 5V, CMOS I/O
Chapter 1
Item
Feature
Specification
•
•
•
•
•
•
•
•
•
•
Upstream accelerated Hub architecture interface for access to GMCH
PCI interface (six PCI Request/Grant pairs)
Bus master IDE controller (support Ultra 33/66/100)
Serial ATA (SATA) controller
USB 1.1 and USB 2.0 host controller
AC’97 2.3 interface
Low Pin Count (LPC) interface
IRQ controller
Enhanced DMA controller, interrupt controller, timers, RTC
Power management
Seagate
Model
ST9120821AS
ST9120824AS
ST98823AS
Formatted Gbytes (512 bytes/sector)
120
100
80
Physical read/write head
4
4
3
Discs
2
2
2
Spindle Speed (RPM)
5400
Internal transfer rate (Mbytes/sec.
max.)
57.6
I/O data transfer rate (Mbytes/sec.
max.)
150
ATA data transfer mode supported
SATA 1.0, SATA II
PIO modes 0-4
Multiword DMA modes 0-2
Ultra DMA modes 0-6
Bytes per sector
1024
Average latency
5.56
Average seek, read (msec. typical)
12.5
Average seek, write (msec. typical)
14.5
Cache buffer
8 Mbytes
Startup current (typical, peak)
+5V: 1.1A
Ambient temperature
5 to 55oC (operating), -40 to 70oC (nonoperating)
Temperature gradient (oC per hour
max.)
20oC (operating), 30oC (nonoperating)
Relative humidity
5% to 90% (operating), 5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max.
Drive acoustics, sound power (bels)
idle
2.4 (typical), 2.6 (max)
Shock, operating (Gs max. at 0.5
msec.)
250
Shock, nonoperating (Gs max. at 2
msec.)
800
Vibration, operating
1.0 G (0 to peak, 5-500 Hz)
Vibration, nonoperating
5 Gs (0 to peak, 5-500 Hz)
Nonrecoverable read errors
1 per 1014 bits read, max.
Drive Specification
Chapter 1
37
Seagate
Seek power (typical)
2.20 watts
Read/write power (typical)
Read: 1.90 watts; Write: 2.30 watts
Idle mode, lower power (typical)
0.80 watts
Standby mode
0.28 watts
Sleep mode
0.28 watts
Voltage tolerance
+5.0V +/- 5%
Item
Description
Chip
ICS954310BGLF or pin compatible device
Package
64-pin TSSOP
Power
3.3V
Feature
• Spread spectrum function support, for reducing EMI
• SM bus interface support
Clock synthesizer
• 133/166 MHz for CPU and GMCH
• 100 MHz clock buffer for GMCH, ICH7M, PCI-E device, SATA and
Docking station
• 96MHz GMCH
• 48MHz for USB clock inside ICH7M
• 33MHz PCI clock for PC device, SIO, LPC
• 14.31818MHz for ICH7M and audio
Item
Feature
Description
•
•
•
•
•
14.31818MHz crystal for clock chip
32.768KHz for RTC inside ICH7M and HS97551
24.576MHz/48MHz O2MICRO OZ711MP1
27MHz crystal for ATI VGA M56P
25MHz crystal for GigaLAN 82573E (Tekoa)
Item
Description
Chipset
Intel 945PM (Calistoga)
Feature
•
•
•
•
®
DDR2 533/667 MHz SDRAM memory interface design
No DDR RAM on board
Two DDR SODIMM slots
Maximum memory up to 2GB for 32bit OS, 4GB for 64bit OS (with two
1GB/2GB SODIMM)
Item
38
Description
Chip
Andigilog aSC7511
Package
Eight-pin SSOP
Interface
I2C bus, address: 98h
Chapter 1
Item
Description
Vendor
Phoenix
Version
v2.002e
ROM type
SST 39VF080, one MB CMOS Boot block Flash Memory
Package
40-pin TSOP
Block size
64KB per block
Supply current
• Active current: 15 mA (typical)
• Standby current: 4 uA (typical)
Item
Description
Chip
ATI M56P with VRAM 128MB/256MB
Package
BGA 708-pin
Feature
•
•
•
•
•
•
•
•
•
PCI-E interface support
3D graphics texturing enhancements
Integrated transform and lighting
Integrated two channels of 24bit LVDS transmitter to support up to
SXGA LCD
Integrated TV decoder to support S-video with both PAL and NTSC
through EZ-4
128MB/256MB DDR3 memory
DVD-ready motion compensation for MPEG-2
Full ACPI compliant
ZV port support
Item
Chip
Description
O2 Micro OZ711MP1
PCMCIA
Feature
• PCI single chip solution, PCI 2.2 compliant
• OHCI v1.1
• IEEE 1394.A four-pin
IEEE 1394
Feature
• PC card 95 support with one Type II PCI Card bus
• Reserved PCI-Express one wide type ME
Memory card reader
Feature
• Five-in-one Card Reader
Item
Description
Controller
NS PC87383
Package
TQFP 64-pin
Chapter 1
39
Item
Description
Feature
Parallel interface support:
• An Enhanced Parallel Port (EPP) compatible with EPP 1.9, version
EPP1.7 of the Xircom specification support
• An extended capabilities port that is IEEE 1284 compliant including
level two
UART serial port interface:
• MIDI baud rate support
• Infrared support on UART2 (IrDA 1.1 support)
PnP support:
• Flexible IRQs, DMAs and base addresses
• IRQs that can be multiplexed to the ten supported IRQs
Power consumption
5V / 25 ~ 55 mA
Item
Description
Chip
Realtek ALC833D Azadia Codec and Amplifier Maxim MAX9755
Feature
• HD Audio
• SNR > 85, high-performance DACs with 95dB SNR (A-Weighting),
ADCs with 85dB SNR (A-Weighting)
• Internal Microphone
• Two speakers, at least 1.5W / 30cc for each
• 2* digital microphone array
• VoIP function support
• Universal jack function support
Item
Intel® Tekoa GigaLAN (82573E)
Feature
•
•
•
•
Connector type
RJ-45
Item
40
Description
Chip
PCI-E GbE LAN
WOL support from S5
LDCM support
Intel® AMT and Wake-on-LAN support
Specification
Model name
HLDS GSA-4082N 8X SUPER
MULTI
PANASONIC UJ-840B SUPER
MULTI
Support disc format
DVD-ROM, DVD-R, DVD-RAM,
DVD-RW, DVD+R, DVD+RW;
CD-ROM, CD-ROM XA, CD-I,
Video CD, CD-Extra, CD-Text,
Photo CD, CD-DA, CD-R, CDRW
DVD-Video, DVD-ROM, DVD-R,
DVD-RW, DVD+R, DVD+R DL,
DVD+RW, CD-DA, CD-ROM,
CD-R, CD-RW, CD-ROMXA,
Photo CD (multisession), Video
CD, CD-Extra (CD+), CD-Text,
Hybrid SACD
Chapter 1
Item
Specification
Transfer rate
DVD-ROM 16.62Mbytes/sec.
(12X) max.
CD-ROM 4800 kB/sec. (32X)
max.
DVD-ROM 10.55 Mbytes/sec.
(8X) max.
CD-ROM 3600 kB/sec. (24X)
max.
Interface
IDE (ATAPI)
IDE (ATAPI)
Operating voltage
+5.0V +/- 5%
+5.0V +/- 5%
Item
Feature
Description
• Mini-card: manufacturing option
• 802.11a/b/g (Intel® Golan / 3rd party)
• 802.11 pre-n (3rd party)
• Built-in two antennas
• Wi-Fi CERTIFIEDTM solution, WPA2, WMM
• CCX V3 and above
Item
Description
Controller
ICH7M
Data modem data baud
rate (bps)
56K
Modem/bluetooth
protocol supported
• V.90/V.92 AC-Link modem with PTT approval
• Wake-on-Ring ready
Connector type
RJ-11
Item
Description
Module
WNC BU5 Bluetooth miniUSB module
Controller
ICH7M
Feature
•
•
•
•
•
•
Bluetooth 1.1 qualified embedded USB module
Class two specification RF output power (max. + four dBm)
Full piconet and scatternet operation
Full Bluetooth data rate (723 KB/s)
USB 1.1 compliant interface
LED indicator built-in
Item
Description
Chip
PC97551
Package
LQFP 176-pin
Feature
•
•
•
•
•
•
•
Chapter 1
Host interface, base on Intel®’s LPC interface specification revision 1.0
PC01 REV 0.3 and ACPI 1.0b compliant
16bit risc core, with two MB address space, up to 20 MHz
Software and hardware controlled clock throttling
Share BIOS flash memory (internal and/or external)
84 GPIO ports with variety of wake-up events
JTAG-base debugger interface
41
Item
Description
Controller
PC97551
Model name
Travelmate series: New Acer Ergo Keyboard with buttons embedded
Feature
•
•
•
•
•
•
•
•
•
•
•
88/89-key Acer FineTouchTM keyboard with five-degree curve
Inverted T cursor layout
2.5 mm (minimum) key travel, spill proof support
Built-in touchpad with four-way integrated scroll button
12 function keys
Four cursor keys
Two Windows® keys
Hotkey controls
Embedded numeric keypad
International language support
Four easy-launch buttons: web browser, mail, empowering key and
user-programmable
• Two front-access recovery type LED switch: WLAN, Bluetooth®
Item
Controller
System core logic
• North bridge: Intel 945PM (Calistoga)
• South bridge: ICH7M
Super I/O
NS PC87383
PCMCIA & IEEE 1394
& Card Reader
O2 711MP1
Audio
Realtek ALC883
Video
ATI M56P
Keyboard
PC97551
LAN
Intel® Tekoa GigaLAN 82573E
®
Item
Feature
Description
•
•
•
•
•
•
•
•
120 pins for signals and four pins for power
Power supplied from Acer ezDock
Max. six USB ports support
Two 1394 ports support
One new card socket and one PCMCIA card socket
GigaLAN and modem support
analog VGA, TV out and DVI-D support
One parallel, one serial port and two PS2 port for legacy devices
support
Item
42
Specification
Vendor & model name
Panasonic pack 7800MAH / Sanyo pack 2600MAH
Battery Type
Li-Ion
Pack capacity
87 W
Number of battery cell
nine cell
six cell (optional: 42 W 3800MAH Li-Ion 2nd battery pack)
Chapter 1
Item
Battery life
Specification
• 80% charge in one hour
• two hour rapid charge system-off
• 2.5 hour charge-in-use
Legacy Mode
ACPI Mode
Off
• Mech. Off (G3): All devices in the system are turned off completely.
• Soft Off: (G2/S5): All devices in the system are turned off completely
by OS shutdown.
On
• Working (G0/S0): Individual devices such as the CPU and hard disk
may be power-managed in this state.
• S3 Sleeping State: CPU set power down, VGA suspend, PCMCIA
suspend, Audio power down, HDD power down, CD-ROM power
down, Super I/O low power mode.
• S4 Sleeping State: It is also called hibernation state. The system
saves all system setting and data onto disk before the whole system
is powered off.
Event
S3
S4
S5
Power Button
Yes
Yes
Yes
LAN (onboard)
Yes
Yes
Yes
This event only runs for onboard LAN.
In S4 and S5, this feature is supported
only with AC in.
RTC
Yes
Yes
Yes
In S4 and S5, this feature is supported
only with AC in.
Lid Open
No
No
No
Embedded Software
Modem
Yes
No
No
USB Input Device
No
No
No
Any Key from Internal
Keyboard
Yes
No
No
PS/2 Input Device
No
No
No
Battery Critically Low
Yes
No
No
Item
Remark
This feature is supported only with AC
in.
This event should wake the system to
Full On then notify the OS of the
critically low batter.
Specification
Model name
Samsung LTN154P1L02
CMO N154Z1-L01
QDI QD 15AL02-01
Display area
331.38 (H) X
207.1125 (V) mm
(15.4” diagonal)
331.128 (H) X
206.955 (V) mm
(15.4” diagonal)
331.2 (H) X 207.0 (V)
mm (15.4” diagonal)
Driver element
a-Si TFT active
matrix
a-Si TFT active
matrix
-
Display colors
262,144
262,144
262,144
Number of pixel
1680 X RGB (3)
X1050 pixels
1680 X RGB (3)
X1050 pixels
1680 X RGB (3)
X1050 pixels
Pixel arrangement
RGB vertical stripe
RGB vertical stripe
RGB vertical stripe
Chapter 1
43
Item
Specification
Pixel pitch
0.19725 (H) X
0.19725 (V) mm
0.1971 (H) X 0.1971
(V) mm
0.1971 (H) X 0.1971
(V) mm
Display mode
Normally white
Normally white
Normally white
Surface treatment
Haze (25), Hardcoating (3H)
Antiglare and Hard
Coat (3H min.)
Antiglare, Hardness
3H
Item
Model name
Specification
LiteOn PA-1900-04QB
ROHS Delta 90W ADP90SB BBAHF
Rated voltage
for 100Vac or 240Vac input
AC voltage
for 100Vac or 240Vac input
AC voltage
Input voltage range
from 90Vac to 264Vac
from 90Vac to 265Vac
Rated frequency
for 50Hz or 60Hz
for 50Hz or 60Hz
Frequency range
from 47Hz to 63Hz
from 47Hz to 63Hz
Steady AC current
less than 1.5A rms at
100Vac input and maximum
load
less than 1.5A rms at
100Vac input and maximum
load
Rated voltage
19V
19V
Voltage range
18.05V to 20V
from 18.2V to 19.8V
Rated power
90 W
90 W
Output ripple and noise
less than 300mVp-p
less than 300mVp-p
Turn on delay time
within two seconds at 115
Vac input voltage
within two seconds at 115
Vac input voltage
Pin Number
three pin
three pin
Input feature
Output feature
Item
44
Description
Dimensions
364 (W) x 271 (D) x 26.3/38 (H) mm (14.33 x 10.66 x 1.03/1.49 inches)
Weight
3 kg (6.6 lbs.) for 15.4 LCD model
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built in the BIOS (Basic Input / Output System) of
computer. Generally speaking, the computer is already properly configured and optimized, and you do not need to
run this utility.
However, if you encounter configuration problems, you may need to run Setup. Otherwise, you can also refer to
Chapter 4 Troubleshooting when problem arises.
Invoking BIOS Setup
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted on
the left-bottom side of the screen).
There are six prime items in the BIOS Setup Utility. They are Information, Main, Advanced, Security, Boot and Exit.
In the coming pages, we will explain the BIOS Setup Utility by item.
Part
Description
Information
Display the system informations.
Main
Allows the user to specify standard IBM PC AT system
parameters.
Advanced
Provides advanced setting of the system.
Security
Provides security setting of the system.
Boot
Allows the user to specify the boot options.
Exit
Allows the user to save CMOS setting and exit Setup.
Note: During setup, all Fn function keys and power saving function are disabled.
Chapter 2
45
Buttons
Hotkeys
•
Fn + F1 (Help Menu): This hotkey will cause a help message on the screen that describes the definitions
and functions of the unit’s hotkeys.
•
Fn + F2 (Launch Acer eSetting): This hotkey will launch the Acer eSetting utility.
•
Fn + F3 (Launch Acer ePower Management): This hotkey will launch the Acer ePower management
utility.
•
Fn + F4 (Sleep Button): It is assigned as the Sleep Button in ACPI mode. Users can set the definition of
Sleep Button in Windows Power Options.
•
Fn + F5 (Display Toggle): It’s used to switch the display device at run-time. The detail behavior is defined
in Acer Display Mode Specification v0.02.
•
Fn + F6 (Display Blank): This hotkey will make the LCD backlight turned off. This provides both a quick
security features and some power savings. The LCD backlight will be turned on again when any of the
following events occurs:
•
Any key pressed (not include USB keyboard)
•
Pointing device moved (not include USB mouse)
•
Fn + F7 (Touchpad On/Off): This hotkey will cause the internal touchpad to be disabled/enabled.
•
Fn + F8 (Speaker On/Off): It’s assigned to turn on and turn off the audio output.
•
Fn + F11 (Number Lock): The NumLock feature is a standard AT keyboard feature. In Acer system, the
NumLock is off by default and for the internal keyboard as numeric keypad lock when the NumLock is on.
If an external keyboard or keypad is linked, the NumLock will have the following limits:
•
NumLock is on when the system boots with external keyboard or numeric keypad. The external
keyboard or keypad NumLock status is on and internal keyboard overlay numeric keys are disabled.
•
NumLock key can be typed on or off via the internal keyboard (Fn + F11) or the external keyboard or
keypad, but NumLock affects the external keyboard or keypad only.
•
The NumLock shift state (NumLock is off) is NOT used for the cursor movement by the internal
keyboard numeric keys.
•
The state of the NumLock is not changed by the linkage and removal of the external keyboard or
keypad. This is to support the linkage of an external numeric keypad. It permits the users for full
alphabet typing with the internal keyboard, and the external keypad for numeric typing.
•
Fn + F12 (Scroll Lock): The Scroll Lock is a standard AT keyboard feature.
•
Fn + K (Volume Up): It is assigned to increase the volume.
•
Fn + L (Volume Down): This hotkey is used to decrease the volume.
•
Fn + J (Brightness Up): It is assigned to increase the brightness of the LCD backlight.
•
Fn + I (Brightness down): It is used to decrease the brightness of the LCD backlight.
•
Fn + <Page Up> (Home): This is a standard AT keyboard feature. When it is pressed, the cursor on the
screen will skip to the beginning of the line.
•
Fn + <Page Down> (End): It is a standard AT keyboard feature. When it is pressed, the cursor on the
screen will skip to the end of the line.
Launch Buttons
•
46
: Launch Acer eManager
•
P: Launch Application (programmable)
•
WWW: Web Browser
•
Email: Launch Email
•
Wireless: Wireless enabled/disabled
•
Bluetooth: Bluetooth enabled/disabled
Chapter 2
Power Button
The Power button should act as the ACPI defined Power button and users can determine its policy through the OS
setting like Windows Power Options.
The override feature should be supported to allow the unconditional shutdown by pressing the Power button for
more than four seconds.
Lid Switch
The function of Lid switch is defined as below:
•
The LCD backlight should be turned off when the Lid switch is pressed. The LCD backlight will be lighted
when the Lid switch is released again. This function is irrelevant to OS and should be always true when
the system is powered on.
•
When the system is running under ACPI mode, the function of the Lid switch should follow the OS setting.
Auto-Dim
The system supports an automatic dimming of the LCD brightness when the AC power source is not available
(running on battery power). However, the users still can manually adjust the LCD brightness by their need. The
current user setting of brightness (along with current power source) will be saved across power down and be
restored at the next boot or resume.
Chapter 2
47
Information Menu
PhoenixBIOS Setup Utility
. Info.
Main
CPU Type:
:
CPU Speed
:
Advanced
Security
Intel(R) Pentium (R) M CPU
2000 MHz
Boot
000
Exit
@ 2.00GHz
HDD Model Name:
ST98823AS
HDD Serial Number: 3PK016YX
ATAPI Device:
HL-DT-ST DVDRAM GSA-4082N
System BIOS Version: v2.002e
VGA BIOS Version: ATi 009.012.001.000
KBC Version:
V.1A17
Serial Number:
LXT123ZC1000420076EF00
Asset Tag Number:
Product Name:
Manufacturer Name:
TravelMate 8200
Acer
UUID:
004CEEEDBC630010AC3AFFFFFFFFFFFF
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
•
HDD Model Name: This item will show the Model name of HDD installed on Primary IDE master. The hard
disk model name is automatically detected by the system. If there is no hard disk present or unknown
type, “None” should be shown on this field.
•
HDD Serial Number: This item will show the Serial number of HDD installed on Primary IDE master. If no
hard disk or other devices are installed on Primary IDE master, it will display a blank line.
•
UUID: It shows only when an internal LAN device is available.
Note: Other items are unit dependent.
48
Chapter 2
Main Menu
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
System Time:
[14:13:43]
System Date:
[11/25/2005]
System Memory:
640 KB
Extended Memory:
1022 MB
Video Memory
256 MB
Quiet Boot:
[Enabled]
Power On Display:
[Both]
Network Boot
[Enabled]
F12 Boot Menu:
[Disabled]
D2D Recovery:
Processor Power Management:
[Enabled]
[Enabled]
<Tab>, <Shift-Tab>, or
<Enter> selects field.
F1 Help
↑↓
←→
Esc Exit
•
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
System Time and System Date: The hours are displayed with 24-hour format. The changes in these two
items take effect immediately.
•
System Memory: This item reports the memory size of system base memory. The size is fixed to 640KB.
•
Extended Memory: It reports the memory size of the extended memory in the system. The extended
memory size is equal to total memory size (one MB).
•
Video Memory: It indicates the video memory size.
•
Quiet Boot:
•
•
Enabled: Customer Logo is displayed, and Summary Screen is disabled.
•
Disabled: Customer Logo is displayed, and Summary Screen is enabled.
Power on Display:
•
Auto: During power on process, the system will detect if any display device is connected on external
video port. If any external display device is connected, the power on display will be only in CRT (or
projector) mode. Otherwise, it will be in LCD mode.
•
Both: Both the integrated LCD and the external video port (for an external CRT or projector) will be
enabled simultaneously.
•
Network Boot: It permits the users to boot from network.
•
F12 Boot Menu:
•
Enabled: When it is enabled, the users can modify device boot priority by pressing <F12> during
POST.
•
Disabled: When it is not enabled, device boot priority will not be adjustable during POST. The boot
Chapter 2
49
device change is only for one-time change. In other words, when the system is rebooted, the boot
device sequence will be the same as the one defined in the BIOS setup (Boot option).
50
•
D2D Recovery: It allows the users to enable or disable the disk-to-disk recovery.
•
Processor Power Management: To save power in working state, the OS leads the CPU to low-power
states (C1, C2 and C3) when the OS is idle. In the low-power state, the CPU does not run any
instructions, and wakes up when an interruption, such as the OS scheduler’s timer interruption, occurs.
Chapter 2
Advanced Menu
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Serial port A:
[Auto]
Infrared Port:
[Auto]
Parallel port:
Mode:
[Auto]
[ECP]
Security
Boot
Exit
Item Specific Help
Configure serial port A
using options:
[Disable]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when
controlled by OS
F1
Help
Esc Exit
•
•
•
•
↑ ↓
← →
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub - Menu
F10 Save and Exit
Serial Port A:
•
Disabled: No configuration
•
Enabled: User configuration
•
Auto: BIOS or OS chooses configuration.
Infrared Port:
•
Disabled: No configuration
•
Enabled: User configuration
•
BIOS or OS chooses configuration.
Parallel Port:
•
Disabled: No configuration
•
Enabled: User configuration
•
Auto BIOS or OS chooses configuration.
Mode: It permits to set the mode for the parallel port. There are four modes: output only, bi-directional,
EPP and ECP.
Chapter 2
51
Security Menu
Info.
Main
PhoenixBIOS Setup Utility
Security
Advanced
Clear
User Password Is:
Clear
HDD Password Is:
HDD Master ID:
Clear
19893803
Set Supervisor Password
Set User Passord
Set HDD Password
[Enter]
[Enter]
[Enter]
Password on boot:
[Disabled]
Esc Exit
↑ ↓
←→
Exit
Item Specific Help
Supervisor Password Is:
F1 Help
Boot
Supervisor Password
controls access to the
setup utility.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The system supports three levels of password protection. The password support consists of a Supervisor
Password, User Password, and Hard Disk Password. All the passwords are stored in a non-volatile storage device
(EEPROM).
•
52
All the passwords will obey the following rules:
•
All the passwords can be set or cleared in BIOS Setup Security screen.
•
The password entry consists of eight alphanumeric characters. At least one character must be
assigned.
•
The valid keys are listed in the table below:
Symbol Character
Symbol Name
A-Z
letters A to Z (not case sensitive)
0-9
numerical characters
-
dash
=
equal sign
[
left bracket
]
right bracket
.
period
,
comma
;
semi-colon
Chapter 2
Symbol Character
•
•
•
•
Symbol Name
/
slash
\
back slash
•
The users can not change or remove password during resuming from S4.
•
The max. number of times to retry the password is limited to three.
Supervisor Password:
•
Supervisor Password controls the access of the whole BIOS Setup Utility. If the Supervisor Password
is set, the system will pop up the password dialog box to ask for the password when the users press
<F2> for entering BIOS Setup Utility.
•
If the Supervisor Password is set and Password on boot is enabled, the system will pop up the
password dialog box to ask for the password when the system is powered on or resumes for S4 state.
•
If the users fail three times consecutively in password verification, the system will be hung up and the
users need to manually power off the system.
User Password:
•
If the User Password is set, the system will pop up the password dialog box to ask for the password
when the users press <F2> for entering BIOS Setup Utility.
•
If the Supervisor Password is not set at first, the User Password can not be set. If the Supervisor
Password is cleared, the User Password will be cleared, too.
•
If the User Password is set and Password on boot is enabled, the system will pop up the password
dialog box to ask for the password when the system is powered on or resumes for S4 state.
•
If the users fail three times consecutively in password verification, the system will be hung up and the
users need to manually power off the system.
Set Supervisor Password / User Password:
•
Highlight the item and press “Enter”, a dialog box will be shown to ask the users to enter new
password and confirm new password.
•
If the users want to reset password, a current password will be required to be tapped in at first. If the
current password is correct, the users are permitted to enter new password and confirm new
password for verification. If the verification is OK, the password setting will be complete after the users
press “Enter”.
•
If the password entered does not match the current password, a dialog box will be shown to ask to reenter the password.
Password on Boot: It allows the user to specify whether or not a password is required to boot.
Chapter 2
53
Boot Menu
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
1: USB KEY:
2: USB FDC:
3: USB HDD: FUJITSU MHT2040AH-(USB 2.
4: IDE 0:
ST98823ASIDE S
5: IDE 1:
6: IDE 2:
HL-DT-ST DVDRAM GSA-4082N
7: USB CDROM:
8: PCI LAN:
IBA GE Slot 0300 v1230
F1 Help
Esc Exit
↑ ↓
←→
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<f> and <r> specifies
the device fixed or
removable.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
<1- 4 > Loads default
boot sequence.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
This menu allows the users to decide the order of bootable devices to load the operating system. It identifies all the
bootable devices in the system and attempts to boot them in the order specified. Bootable devices include the
diskette drive in module bay, the hard disk and the CD-ROM/DVD drive in module bay and onboard LAN device.
54
Chapter 2
Exit Menu
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
•
Exit Saving Changes: It allows the users to save changes to CMOS and reboot the system.
•
Exit Discarding Changes: The users can exit the Setup not to save changes.
•
Load Setup Defaults: It allows the users to load default values in CMOS Setup.
•
Discard Changes: The users can discard previous changes in CMOS Setup.
•
Save Changes: The users can save current changes in CMOS Setup.
Chapter 2
55
Chapter 3
Machine Disassembly and Replacement
General Information
This chapter contains step-by-step procedures on how to disassemble the notebook for maintenance and
troubleshooting.
To disassemble the computer, you need the tools below:
•
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Plastic flat head screw driver
•
Hexagonal driver
•
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components. When you
remove the stripe cover, please be careful not to scrape the cover.
Before You Begin
Before proceeding with the disassembly procedure, you have to make sure that:
1. The system and all peripherals are powered off.
2. The AC adaptor and all power and signal cables from the system are unplugged.
3. The battery pack is removed.
Note: There are several types of screws used to secure the main unit. The screws vary in length. Please refer
to the screws table after the flowchart. Group the same type of screws together during service disassembling.
Please also remember the screw location for each screw type. If you fasten the screws on the wrong location,
the long screws may cause irrecoverable damage to the main board.
Chapter 3
56
Disassembly Procedure Flowchart
The flowchart gives you a graphic representation on the entire disassembly and reassembly and instructs you how
to remove the components.
Item
57
Description
a
SCREW M2.0*2.5-I (NI) (NYLOK)
b
SCREW M2.5*6-I (BNI) (NYLOK)
c
SCREW M2.0*3.0-I-NI-NYLOK
d
SCREW M2.0*6.0-I-NI-NYLOK
e
SCREW M2.5*2-I (NI, NYLOK)
Chapter 3
Item
Description
f
SCREW 2.5*3-I (NI, NYLOK)
g
SCREW 2.5*6-I (BNI) TAP
h
SCREW M2.5*4-I (BNI)
i
SCREW M2.5*4.0-I (NYLOK) EU
j
NUT IO EA1
Chapter 3
58
Disassembly Procedure
Removing the Battery Pack
1. Unlock the battery pack.
2. Slide the battery latch, hold it then remove the battery.
Removing the HDD Module
1. Release the two screws fastening the HDD module cover.
2. Detach the HDD module cover.
3. Release the screw fastening the HDD module.
4. Pull the HDD module backwards carefully then remove it.
59
Chapter 3
Removing the Memory and the MiniPCI Card
1. Release the five screws fastening the heatsink cover.
2. Detach the heatsink cover.
3. Pop up the memory card.
4. Then remove it from the slot.
5. Disconnect carefully the main wireless antenna and the auxiliary wireless antenna.
6. Release the two screws fastening the miniPCI card then remove the miniPCI card.
7. Disconnect carefully the bluetooth module.
8. Slide the latch then remove the ODD module from the main unit.
Chapter 3
60
Disassembling the Main Unit
1. To remove the middle cover, you have to remove the two screws on the rear side.
2. Open the notebook as shown. Detach the middle cover carefully because the cable of LED board and main
board is under the middle cover.
3. Disconnect the middle cover side cable then remove the middle cover.
4. Release the connector then disconnect the main board side cable as shown.
5. Remove the two screws fastening the keyboard.
6. Detach the keyboard carefully then turn it over as shown.
7. Disconnect the keyboard then remove the keyboard.
8. Disconnect the LCD cable.
9. Pull out the wireless antenna set from the main unit carefully.
61
Chapter 3
10. Disconnect the microphone line and take it out from the main unit carefully.
11. To detach the LCD module, you have to remove the four screws fastening the LCD hinges and the main unit.
12. There is a metal ring fastened on the right hinge. Do not mismatch when reassembling.
13. Then detach the LCD module.
14. Disconnect the touchpad cable.
Chapter 3
62
15. To separate the upper case from the main unit, you have to remove seven screws fastening the upper and
lower case assembly.
16. Then remove the 18 screws on the bottom side of the main unit holding the upper and lower cases. One of
these 18 screws secures the fan (marked in red).
17. Finally, remove the two hexagonal screws on the rear side of the main unit.
18. Now detach the upper case from the main unit.
19. Release the connector and disconnect the Smart Card reader cable.
20. Disconnect the USB board cable.
21. Disconnect the speaker set cable.
22. Disconnect the other USB board cable on the bottom side of the main unit.
23. Disconnect the fan cable.
63
Chapter 3
24. Remove the two screws fastening the fan.
25. Then detach the fan.
26. Remove the two screws fastening the modem board.
27. Detach the modem board from the main board carefully then disconnect it.
28. Remove the screw fastening the main board.
29. Separate the main board from the lower case carefully.
30. Disconnect the RTC battery on the main board then detach it.
31. Release the five screws fastening the heatsink then detach the heatsink.
32. Release the screw fastening the CPU by rotating the screw counter clockwise then detach the CPU.
33. Remove the screw fastening the charge board then detach it from the main board.
Chapter 3
64
34. Remove the three screws fastening the Smart Card reader then detach the Smart Card reader from the lower
case.
35. Pull the latch backwards softly and detach the USB board from its position.
36. Then disconnect carefully the four-pin USB cable, 10-pin USB cable and modem cable.
37. Detach the bluetooth module from the upper case.
65
Chapter 3
38. Disconnect the click-button cable then remove it.
39. Disconnect the cable linking the click buttons and touchpad then remove it.
40. Remove the three screws fastening the click-button bracket then detach the click-button bracket.
41. Remove the four screws fastening the touchpad bracket then detach the touchpad bracket.
42. Then detach the touchpad.
43. Finally, remove the three screws securing the LED board then detach the LED board from the middle cover.
Chapter 3
66
Disassembling the LCD Module
1. Detach the six LCD screw rubber cushions and remove the six screws fastening the LCD bezel.
2. Then carefully detach the LCD bezel.
3. Detach inverter board then disconnect the LCD backlight cable and the inverter cable.
4. Remove the four screws securing the LCD bracket.
5. Disconnect the CCD module.
6. Detach the LCD.
67
Chapter 3
7. Remove the two screws fastening the LCD right bracket and detach the bracket.
8. Remove the two screws fastening the LCD left bracket and detach the bracket.
9. Carefully detach the tapes then disconnect the LCD cable.
10. Remove the two screws fastening the antenna set.
11. Then carefully detach the antenna set from the LCD panel.
12. Remove the two screws fastening the LCD panel latch.
13. Take out the left LCD panel latch lock with tweezers.
14. Take out the right LCD panel latch lock with tweezers.
15. Then remove the latch.
Chapter 3
68
16. Remove the screw fastening the CCD module.
17. Detach the CCD module carefully from the LCD panel.
Disassembling the ODD Module
1. Remove the four screws fastening the ODD holder and detach the ODD holder.
2. Insert a screwdriver or a clip into the emergency eject hole to eject the optical disk drive as shown
3. Then detach the ODD bezel.
69
Chapter 3
Disassembling the CCD Module
1. Detach the CCD module holder.
2. Separate the cases of the CCD module.
3. Remove the two screws fastening the CCD board and detach the CCD board.
Disassembling the HDD Module
1. Remove the two screws securing the HDD bracket and detach the HDD bracket.
Chapter 3
70
Chapter 4
Troubleshooting
Please use the following procedures as a guide for computer problems.
Note: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options may occur errors or invalid responses.
1. Obtain the detailed fail symptoms as many as possible.
2. Verify the symptoms by attempting to recreate, running the diagnostic tests or repeating the same operation.
Chapter 4
71
System Check Procedures
External Diskette Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or diskette. A writable,
diagnostic diskette is required.
Note: Make sure that the diskette does not have more than one label attached. Multiple labels may cause
damage to the drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if FDD test is passed as the programs run the FDD test.
3. Follow the instructions in the message window.
If errors occur with the internal diskette driver, reconnect the diskette connector on the system board. If the errors
still remain:
1. Reconnect the external diskette drive.
2. Replace the external diskette driver.
3. Replace the main board.
External CD-ROM Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or CD-ROM.
Note: Make sure that the CD-ROM does not have any label attached. The label may cause damage to the
drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if CD-ROM test is passed when the programs run the CD-ROM test.
3. Follow the instructions in the message window.
If errors occur, reconnect the connector on the system board. If the errors still remain:
1. Reconnect the external CD-ROM drive.
2. Replace the external CD-ROM drive.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is under test. If the internal keyboard does not work or an
unexpected error appears, make sure that the flexible cable extending from the internal keyboard is correctly
connected on the system board. If the keyboard is correctly connected, run the Keyboard test.
If errors occur, do the following procedures in sequence to correct the problems. Do not replace a non-defective
FRU.
1. Reconnect the keyboard cable.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer.
T
Numeric keypad
T
External keyboard
If any of these devices do not function, reconnect the cable and repeat the anterior procedures.
Memory Check
Follow the procedures below to correct the memory errors.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. Go to the diagnostic memory in the test items.
72
Chapter 4
3. Press F2 in the test items.
4. Follow the instructions in the message window.
Note: Make sure that the DIMM is correctly inserted into the connector. A wrong connection will cause errors.
Power System Check
To verify the symptoms, power on the computer by using the following power sources separately.
1. Remove the battery pack.
2. Connect the power adaptor and check the power supply.
3. Disconnect the power adaptor and install the battery pack, then check the power supply.
If you think there is a power supply problem, please go to “Check the Power Adaptor” and “Check the Battery
Pack” in this chapter.
Check the Power Adaptor
Unplug the power adaptor cable from the computer and measure the output voltage at the plug of the power
adaptor cable. See the illustration and follow the procedures below.
pin 1: +19V to +20.5V
pin 2: 0V, ground
1. If the voltage is not correct, replace the power adaptor.
2. If the voltage is within the range:
(1) Replace the system board.
(2) If the problem is still not resolved, see “Undetermined Problems”.
(3) If the voltage is not correct, go to the next step.
Note: An audible noise from the power adaptor does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adaptor for continuity and correct
installation.
4. If the operational charge does not work, see “Check the Battery Pack”.
Check the Battery Pack
Follow the procedures below to check the battery pack.
From software, this helps to identify the problem is on recharging or discharging.
1. Check the Power Management in Control Panel.
2. Then confirm that the parameters shown in the screen for Current Power Source and Total Battery Power
Remaining are correct.
3. Repeat the step 1 and step 2 for both battery and adaptor.
From hardware, this helps to identify whether you should replace the battery pack or not.
1. Power off the system.
2. Remove the battery pack and measure the voltage between terminals one (+) and seven (-). There are seven
terminals totally. See the illustration below.
Chapter 4
73
3. If the voltage is still less than 7.5V after recharging, replace the battery.
If the battery status indicator does not light up, remove the battery pack. After the battery pack returns to room
temperature, reinstall it to the system.
If the charge indicator does not light up, replace the battery pack. If the charge indicator still does not light up,
replace the AC/DC charger board.
Touchpad Check
If the touchpad does not work, follow the procedures one at a time to correct the problem. Do not replace a nondefective FRU.
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement will
occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem.
74
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes.
Note: Perform the FRU replacement or actions in the sequence shown in Error Message List, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
The error messages are listed in the coming pages to indicate the BIOS signals on the screen and the error
symptoms classified by functions. If the symptom is not included on the list, please refer to “Undetermined
Problems”.
Note: Most of the error messages occur during POST. Some of them show information about a hardware
device, for example, the size of memory installed. Others may indicate problems with a device, such as the
way it has been configured.
Note: If the system fails after you make changes in the BIOS Setup Utility menus, please reset the computer.
Enter Setup and install Setup defaults to correct the errors.
Index of Error Messages
Error Code
006
Error Message
Equipment Configuration Error Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
The causes will be shown before “Equipment Configuration Error”.
010
Memory Error at xxxx:xxxx:xxxxh (R: xxxxh, W: xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
No error code
Battery critical low: In this situation BIOS will issue four short beeps
then shut down system, no message will be shown.
No error code
Thermal critical high: In this situation BIOS will shut down the system,
no message will be shown.
Error Message
FRU/Action in Sequence
Failure Fixed Disk
Reconnect hard disk drive connector.
Run “Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see ”Keyboard or Auxiliary Input Device Check”.
Keyboard error
see ”Keyboard or Auxiliary Input Device Check”.
Keyboard Controller Failed
see ”Keyboard or Auxiliary Input Device Check”.
Keyboard locked - Unlock key
switch
Unlock external keyboard
Monitor type does not match
CMOS - Run Setup
Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset:
nnnn
BIOS ROM
System board
Chapter 4
75
Error Message
76
FRU/Action in Sequence
System RAM Failed at offset:
nnnn
DIMM
System board
Extended RAM Failed at offset:
nnnn
DIMM
System board
System battery is dead Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to
reconfigure system time, then reboot system.
System CMOS checksum bad Default configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Previous boot incomplete Default configuration used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST
differed from CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type
in BIOS Setup Utility.
See “External Diskette Drive Check”.
Incorrect Drive A type - run
Setup
Check the drive is defined with the proper diskette type
in BIOS Setup Utility.
System cache error - Cache
disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration
Data
BIOS ROM
System board
Chapter 4
Error Message
FRU/Action in Sequence
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are
properly identified.
Diskette drive
Hard disk drive
System board
No beep, power-on indicator
turns off and LCD is blank.
Power source (battery pack and power adapter). See
“Power System Check”.
Ensure every connector is connected correctly.
Reconnect the DIMM.
LED board
System board
No beep, power-on indicator
turns on and LCD is blank.
Power source (battery pack and power adapter). See
“Power System Check”.
Reconnect the LCD connector.
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator
turns on and LCD is blank. But
you can see POST on an
external CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator
turns on and a blinking cursor
shown on LCD during POST.
Ensure every connector is connected tightly and
correctly.
System board
No beep during POST but
system runs correctly.
Speaker
System board
Chapter 4
77
POST Code
Code
For Boot Block in Flash ROM
E0h
Initialize the chipset.
E1h
Initialize the bridge.
E2h
Initialize the CPU.
E3h
Initialize the system timer.
E4h
Initialize system I/O.
E5h
Check force recovery boot.
E6h
Checksum BIOS ROM.
E7h
Go to BIOS.
E8h
Set Huge Segment.
E9h
Initialize Multi Processor.
EAh
Initialize OEM special code.
EBh
Initialize PIC and DMA.
ECh
Initialize Memory type.
EDh
Initialize Memory size.
EEh
Shadow Boot Block.
EFh
System memory test.
F0h
Initialize interrupt vectors.
F1h
Initialize Run Time Clock.
F2h
Initialize video.
F3h
Initialize System Management Mode.
F4h
F5h
78
Beeps
1
Output one beep before boot.
Boot to Mini DOS.
F6h
Clear Huge Segment.
F7h
Boot to Full DOS.
Chapter 4
Index of Symptom-to-FRU Error Message
Symptom/Error
Action in Sequence
LCD backlight doesn't work.
LCD is too dark.
LCD brightness cannot be adjusted.
LCD contrast cannot be adjusted.
Enter BIOS Utility to execute “Load Setup Default
Settings”, then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key do
not work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or vertical
lines displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Symptom/Error
Indicator incorrectly
remains off or on, but
system runs correctly.
Symptom/Error
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Action in Sequence
Power shuts down during
operation.
Power source (battery pack and power adapter). See “Power
System Check”.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power
on.
Power source (battery pack and power adapter). See “Power
System Check”.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t
power-off.
Power source (battery pack and power adapter). See Power
System Check”.
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged.
See “Check the Battery Pack”.
Battery pack
System board
Chapter 4
79
Symptom/Error
Action in Sequence
System cannot detect the
PC Card (PCMCIA).
PCMCIA slot assembly
System board
PCMCIA slot pin is
damaged.
PCMCIA slot assembly
Symptom / Error
Memory count (size)
appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings,
then reboot system.
DIMM
System board
Symptom/Error
Action in Sequence
In Windows, multimedia
programs, no sound
comes from the computer.
Audio driver
Speaker
System board
Internal speakers make
noise or emit no sound.
Speaker
System board
Symptom/Error
80
Action in Sequence
The system will not enter
hibernation.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system does not
enter hibernation mode
and four short beeps
every minute.
Press Fn + F4 and see if the computer enters hibernation
mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system does not
enter standby mode after
closing the LCD.
LCD cover switch
System board
The system does not
resume from hibernation
mode.
Hard disk connection board
Hard disk drive
System board
The system does not
resume from standby
mode after opening the
LCD.
LCD cover switch
System board
Battery fuel gauge in
Windows does not go
higher than 90%.
Remove battery pack and let it cool for two hours.
Refresh battery (continue to use battery until power off, then
charge battery).
Battery pack
System board
System hangs
intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Chapter 4
Symptom/Error
Action in Sequence
System configuration
does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”,
then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not
work correctly.
Press Fn + F5, LCD/CRT/Both display switching
System board
USB does not work
correctly.
System board
Print problems
Ensure the “Parallel Port” in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port
device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS
Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Symptom/Error
Action in Sequence
Keyboard (one or more
keys) does not work.
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Symptom/Error
Internal modem does not
work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
Note: If you can not correct the problems according to the anterior tables, see “Undetermined Problems”.
Chapter 4
81
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware
defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a recurring problem exists.
When analyzing an intermittent problems, follow the procedures below:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
82
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which devices fail, which devices are incorrectly installed, whether a
short circuit happens, or whether the system is inoperative.
Note: Verify if all devices attached are supported by the computer.
Note: Verify if the power supply used at the time of failure is operating correctly. You can refer to “Power
System Check”.
Follow the procedures below to isolate the failing FRU. Do not isolate non-defective FRU.
1. Power off the computer.
2. Visually check the devices. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery Pack
•
Hard disk drive
•
DIMM
•
CD-ROM / Diskette drive module
•
PC cards
4. Power on the computer.
5. Determine if the problem has been resolved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failed FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU.
•
System board
•
LCD assembly
Chapter 4
83
Chapter 5
Jumper and Connector Locations
Top View of Main Board
Chapter 5
84
Part One of Top View
Part Two of Top View
85
Chapter 5
Part Three of Top View
Item
Description
Item
Description
CN20
SVIDEO
CN32
RTC battery connector (two
pin)
CN21
Docking
CN33
HDD connector (22 pin
SATA)
CN22
DVI-D
CN37
Connector SMD FFC 30 pin
CN23
CRT connector
CN38
Bluetooth module connector
(five pin)
CN24
mini card connector
U37
V-RAM
CN25
RJ45 W/ LED
U40
V-RAM
CN26
Battery connector (seven
pin)
U41
VGA chip
CN28
Fan connector
U43
CPU
CN29
Media connector (M/B side)
U44
North bridge
CN30
DDR2 (9.2MM)
U48
South bridge
CN31
DDR2 (5.2MM)
U57
BIOS
Chapter 5
86
Bottom View
Part One of Bottom View
87
Chapter 5
Part Two of Bottom View
Part Three of Bottom View
Item
Description
Item
Description
CN02
Mic connector (two pin)
CN15
Speaker connector (four pin)
CN03
Main board to button board
FFC connector (16 pin)
CN16
1394 (four pin)
CN04
LCD connector (40 pin)
CN17
SPDIF (line out)
CN05
daughter board cable to
main board (10 pin)
CN18
Audio jack/line in
CN06
Keyboard FFC connector
(25 pin)
CN19
Audio jack/mic
CN07
Touchpad FFC connector
(four pin)
U06
V-RAM
CN08
USB
U10
V-RAM
CN09
USB
U28
IR module
CN10
Smart card FFC connector
SW02
Slider switch
CN12
PCMCIA card header
SW03
Slider switch
CN14
Five-in-one card reader
Chapter 5
88
Chapter 6
FRU (Field Replaceable Unit) List
This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Travelmate 8210/ 8200 series.
Refer to this chapter whenever ordering the parts to repair or for RMA (Return Merchandise Authorization).
Please note that when ordering FRU parts, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed
service guide. For Acer authorized service providers, your Acer office may have a different part number code from
those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional
Acer office to order FRU parts for service.
Note: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
89
Exploded Diagram
90
Chapter 6
Parts
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
ADAPTER
N/A
ADAPTER 90W 3 PIN LITEON PA1900-04QB ROHS
ZC1 ADAPTER LITEON S/P
AP.09003.009
ADAPTER 90W 3 PIN DELTA ADP90SB BBAHF ROHS
ZC1 ADAPTER DELTA S/P
AP.09001.005
BATTERY SANYO LI-ION COMO 9
CELL 2.6
ZC1 BATTERY SANYO 9
CELL S/P
BT.00903.005
BATTERY PANASONIC LI-ION
COMO 9 CELL 2.6
ZC1 BATTERY PANASONIC 9
CELL S/P
BT.00905.001
PRISMATIC COMO 2ND 6 CELL
1.9 P SANYO PACK 3800MAH
ZC1 2ND BATTERY SANYO 6
CELL S/P
BT.00603.015
MODEM BOARD 56K (MDC)
T60M893.T00 S/P
ZF1 MODEM 56K (MDC)
T60M893.T00 S/P
54.T72V7.001
BLUETOOTH MODULE
FOXCONN T60H928.01 W/
ANTENNA
ZC1 FOX BULETOOTH
(T60H928.01) S/P
54.TAXV7.001
MINI PCI WIRELESS BOARD
802.11 A/B/G MOW2 INTEL
MM872659
ZC1 W/L 3945ABG MOW2 S/P
KI.GLN01.002
MINI PCI WIRELESS BOARD
802.11 A/B/G MOW1 INTEL
MM872612
ZC1 W/L 3945ABG MOW1 S/P
KI.GLN01.001
MINI PCI WIRELESS BOARD
802.11 A/B/G ROW INTEL
MM874511
ZC1 W/L 3945ABG ROW S/P
KI.GLN01.003
TOUCHPAD BOARD
ZC1 TOUCHPAD BOARD
ASSY S/P
55.TAXV7.001
POWER BOARD
ZC1 POWER BOARD ASSY
S/P
55.TAXV7.002
BUTTON BOARD
ZC1 BUTTON BOARD ASSY
S/P
55.TAXV7.003
USB BOARD
ZC1 USB BOARD ASSY S/P
55.TAXV7.004
LCD INVERTER BOARD W/ TYPE
ZF1 INV (8-20V, V=700,
REV=A1A) S.P.
19.TAXV7.001
OPTICAL DEVICE CONNECTOR
BOARD
ZC1 CD ROM BOARD ASSY
S/P
55.TAXV7.005
BOARD
Chapter 6
91
CABLE
N/A
92
POWER CORD US 3 PIN ROHS
ZB1 PWR CORD US S/P
TBD
POWER CORD EU 3 PIN ROHS
ZB1 PWR CORD (CEE) S/P
TBD
POWER CORD UK 3 PIN ROHS
TBD
TBD
POWER CORD ITALIAN 3 PIN
ROHS
TBD
TBD
POWER CORD DANISH 3 PIN
ROHS
TBD
TBD
POWER CORD SWISS 3 PIN
ROHS
TBD
TBD
POWER CORD PRC 3 PIN ROHS
TBD
TBD
POWER CORD US-110V (BSMI)
ROHS
TBD
TBD
POWER CORD AU W/ LABEL 3
PIN ROHS
TBD
TBD
POWER CORD AF 3 PIN ROHS
TBD
TBD
POWER CORD AF-S INDIA ROHS
TBD
TBD
POWER CORD KOREA 2 PIN
ROHS
TBD
TBD
POWER CORD JAPAN ROHS
TBD
TBD
POWER CORD ISRAEL 3 PIN
ROHS
TBD
TBD
POWER CORD US 3 PIN
ET2S POWER CORD S/P US
27.A03V7.001
POWER CORD EU
ZC1 POWER CORD EU S/P
TBD
POWER CORD UK
ET2S POWER CORD SPARE
PART UK
TBD
POWER CORD CONTINENTAL
EI2 POWER CORD 3P
CONTINENTAL S.P.
TBD
POWER CORD ISRAEL
ZL6A POWER CORD S/P ISR
S.P.
TBD
POWER CORD ITALIAN
EI2 POWER CORD 3P ITALY
S.P.
TBD
POWER CORD SWISS
ZE1 POWER CORD 3P
SWISS S.P.
TBD
POWER CORD US-110V (BSMI)
ZL3E POWER CORD S/P
TWN
TBD
POWER CORD AF 3 PIN
ZI5 POWER CORD S/P AF
27.T48V7.001
POWER CORD DANISH 3 PIN
ET2S POWER CORD S/P
DANISH
27.A03V7.006
POWER CORD AUSTRALIA W/
LABEL
ZL6A POWER CORD S/P AU
S.P.
TBD
POWER CORD SOUTH AFRICA-S
(INDIA)
ZL6A POWER CORD S/P
INDIA S.P.
TBD
POWER CORD US-110V
ZL3E POWER CORD S/P
THAI
TBD
POWER CORD JAPAN
TBD
TBD
POWER CORD PRC 3 PIN
ET2S POWER CORD S/P
PRC
27.A03V7.003
MODEM CABLE
ZC1 CABLE MDC (2/2P,
REV1A) S/P
50.TAXV7.001
FFC CABLE TOUCHPAD BOARD
TO MAIN BOARD LF
ZC1 CABLE MB TP/B
(122.5MM, 4/4, 2A) S/P
50.TAXV7.002
Chapter 6
N/A
N/A
FFC CABLE BUTTON BOARD TO
MAINBOARD LF
ZC1 CABLE BUTTON BOARD
(60MM, 16/16, 2A) S/P
50.TAXV7.003
FFC CABLE - TP/B TO TP LF
ZC1 CABLE TP/B TO TP
(76MM, 12/12, 2A) S/P
50.TAXV7.004
USB CABLE - 10/10P
ZC1 CABLE USB (10/10P,
REV1A) S/P
50.TAXV7.005
USB CABLE - 4/4P
TBD
50.TAXV7.006
LCD CABLE 15.4 IN. WXGA
ZC1 CABLE 15" SXGA + ID5
(40/40P R1A) S/P
50.TAXV7.007
DCIN CABLE
ZC1 CABLE DCIN (5/5P,
REV1A) S/P
TBD
MIDDLE COVER
ZC1 KB COVER ASSY S/P
42.TAXV7.001
UPPER CASE W/ TP
ZC1 TOP ASSY S/P
60.TAXV7.001
LOWER CASE W/ SPEAKER
ZC1 BASE CASE ASSY S/P
60.TAXV7.002
THERMAL DOOR
ZC1 THERMAL DOOR ASSY
S/P
42.TAXV7.002
TP BOARD SUPPORT BRACKET
ZC1 TP BD SUPPORT
BRACKET S/P
33.TAXV7.001
DUMMY-NEW CARD
ZC1 DUMMY-NEW-CARD S/P
42.TAXV7.003
OPTICAL DEVICE HOLDER
ZC1 ODD-HOLDER S/P
42.TAXV7.006
SUPER MULTI G BASE BEZEL
ZC1 SUPER MULTI BEZEL
ASSY S/P
42.TAXV7.007
HDD BRACKET
ZC1 HDD BRACKET S/P
33.TAXV7.002
CASE / COVER / BRACKET ASSEMBLY
N/A
Chapter 6
93
HDD DOOR
ZC1 HDD DOOR ASSY S/P
42.TAXV7.004
LCD PANEL CARBON 15.4 IN. W/
LOGO ANTENNA CCD MODULE
ZC1 15.4 LCD COVER Carbon
ASSY S/P
60.TAXV7.004
LCD BEZEL W/ RUBBER PAD 15.4
IN.
ZC1 15.4 LCD BEZEL ASSY
S/P
60.TAXV7.005
LCD BRACKET W/HINGE 15.4 IN.
-L
ZC1 HINGE-L S/P
33.TAXV7.004
LCD BRACKET W/HINGE 15.4 IN.
-R
ZC1 HINGE-R S/P
33.TAXV7.005
N/A
PCMCIA SLOT
ZF1 PCMCIA SLOT ASSY S.P
22.T72V7.001
N/A
2ND HDD BASE ASSY
ZC1 2ND HDD BASE ASSY S/
P
60.TAXV7.003
N/A
2ND HDD BRACKET
ZL1 2ND BRACKET ASSY S/P
33.TAXV7.003
N/A
2ND HDD COVER ZC1
(EBZC1027, REV3A) LF
ZC1 2ND HDD COVER S/P
42.TAXV7.005
WIRELESS LAN ANTENNA
ZC1 ANTENNA
(81.ED415.009) S/P
50.TAXV7.011
CPU INTEL YONAH CORE DUO
FSB-667 2.16G 2M L8VN
ZC1 Intel CPU YONAH 2.16G
S/P
KC.26001.DTP
CPU INTEL YONAH CORE DUO
FSB-667 2.0G 2M L8VP
ZC1 Intel CPU YONAH 2.0G
S/P
KC.25001.DTP
CPU INTEL YONAH CORE DUO
FSB-667 1.83G 2M L8VQ
ZC1 Intel CPU YONAH 1.83G
S/P
KC.24001.DTP
CPU INTEL YONAH CORE DUO
FSB-667 1.66G 2M L8VR
ZC1 Intel CPU YONAH 1.66G
S/P
KC.23001.DTP
COMMUNICATION MODULE
N/A
CPU
DVD RW DRIVE
94
Chapter 6
DVD SUPER MULTI HLDS GSA4082N
ZC1 SUPER MULTI HLDS
GSA-4082N ASSY S/P
6M.TAXV7.001
DVD SUPER MULTI DRIVE HLDS
GSA-4082N DL G BASE
ZF1A SUPER MULTI (HLDS
GSA-4082N) S/P
KU.0080D.017
DVD SUPER MULTI PAN UJ-850
ZC1 DVD SUPERMUTI PAN
UJ850 ASSY S/P
6M.TAXV7.002
DVD SUPER MULTI UJ-850BAA-A
FW1.5
ZC1 DVD SUPERMUTI PAN
UJ850 S/P
KU.00807.025
HDD 80GB 2.5 IN. SEGATE
MERCURY2 ST98823AS FW:3.06
LF
ZC1 HDD Seagate 80G S/P
KH.08001.023
HDD 100GB 2.5 IN. SEGATE
MERCURY2 ST9100824AS
FW:3.06 LF
ZC1 HDD Seagate 100G S/P
KH.10001.008
HDD 120GB 2.5 IN. SEGATE
MERCURY2 ST9120821AS
FW:3.06 LF
ZC1 HDD Seagate 120G S/P
KH.12001.025
TM8200 KEYBOARD DARFON US
INTERNATIONAL
ZC1 K/B MODULE (UI) S/P
KB.TAX07.001
TM8200 KEYBOARD DARFON
CHINESE
ZC1 K/B MODULE (TAIWAN)
S/P
KB.TAX07.002
TM8200 KEYBOARD DARFON
SPANISH
ZC1 K/B MODULE (SPANISH)
S/P
KB.TAX07.003
TM8200 KEYBOARD DARFON
THAI
ZC1 K/B MODULE (THAI) S/P
KB.TAX07.004
TM8200 KEYBOARD DARFON
BRAZILIAN PROTUGESE
ZC1 K/B MODULE (BRAZIL)
S/P
KB.TAX07.005
TM8200 KEYBOARD DARFON
KOREA
ZC1 K/B MODULE (KOREAN)
S/P
KB.TAX07.006
TM8200 KEYBOARD DARFON UK
ZC1 K/B MODULE (UK) S/P
KB.TAX07.007
HDD
KEYBOARD
Chapter 6
95
96
TM8200 KEYBOARD DARFON
GERMAN
ZC1 K/B MODULE (GERMAN)
S/P
KB.TAX07.008
TM8200 KEYBOARD DARFON
ITALIAN
ZC1 K/B MODULE (ITALIAN)
S/P
KB.TAX07.009
TM8200 KEYBOARD DARFON
FRENCH
ZC1 K/B MODULE (FRENCH)
S/P
KB.TAX07.010
TM8200 KEYBOARD DARFON
SWISS/G
ZC1 K/B MODULE (SWISS) S/
P
KB.TAX07.011
TM8200 KEYBOARD DARFON
PORTUGUESE
ZC1 K/B MODULE
(PORTUGUESE) S/P
KB.TAX07.012
TM8200 KEYBOARD DARFON
ARABIC
ZC1 K/B MODULE (ARAB-EN)
S/P
KB.TAX07.013
TM8200 KEYBOARD DARFON
BELGIUM
ZC1 K/B MODULE (BELGIUM)
S/P
KB.TAX07.014
TM8200 KEYBOARD DARFON
SWEDEN
ZC1 K/B MODULE
(SWEDISH) S/P
KB.TAX07.015
TM8200 KEYBOARD DARFON
CZECH
ZC1 K/B MODULE (CZECH)
S/P
KB.TAX07.016
TM8200 KEYBOARD DARFON
HUNGAIAN
ZC1 K/B MODULE
(HUNGARIAN) S/P
KB.TAX07.017
TM8200 KEYBOARD DARFON
NORWAY
ZC1 K/B MODULE
(NORWEGIAN) S/P
KB.TAX07.018
TM8200 KEYBOARD DARFON
DANISH
ZC1 K/B MODULE (DANISH)
S/P
KB.TAX07.019
TM8200 KEYBOARD DARFON
TURKISH
ZC1 K/B MODULE (TURKISH)
S/P
KB.TAX07.020
TM8200 KEYBOARD DARFON
CANADIAN FRENCH
ZC1 K/B MODULE (FRA-CAN)
S/P
KB.TAX07.021
TM8200 KEYBOARD DARFON
JAPANESE
ZC1 K/B MODULE (JA) S/P
KB.TAX07.022
TM8200 KEYBOARD DARFON
GREEK
ZC1 K/B MODULE (GREEK)
S/P
KB.TAX07.023
TM8200 KEYBOARD DARFON
HEBREW
ZC1 K/B MODULE (HEBREW)
S/P
KB.TAX07.024
TM8200 KEYBOARD DARFON
RUSSIAN
ZC1 K/B MODULE (RUSSIAN)
S/P
KB.TAX07.025
TM8200 KEYBOARD DARFON
SLOVENIA (SLO)
ZC1 K/B MODULE (SLOVAK)
S/P
KB.TAX07.026
TM8200 KEYBOARD DARFON
CROATIA (CR)
ZC1 K/B MODULE
(CROATIAN) S/P
KB.TAX07.027
TM8200 K/B MODULE FARSI
ZC1 K/B MODULE (FARSI) S/
P
TBD
TM8200 K/B MODULE
BULGARIAN
ZC1 K/B MODULE
(BULGARIAN) S/P
TBD
TM8200 K/B MODULE POLAND
ZC1 K/B MODULE (POLAND)
S/P
TBD
TM8200 K/B MODULE CHINA
ZC1 K/B MODULE (CHINA) S/
P
TBD
TM8200 K/B MODULE DUTCH
ZC1 K/B MODULE (DUTCH)
S/P
TBD
TM8200 K/B MODULE LA
ZC1 K/B MODULE (LA) S/P
TBD
TM8200 K/B MODULE ICELAND
ZC1 K/B MODULE (ICELAND)
S/P
TBD
TM8200 K/B MODULE US
ZC1 K/B MODULE (US) S/P
TBD
Chapter 6
LCD
LCD MODULE 15.4 IN. CARBON
ASSY W/ ANTENNA CCD
ZC1 LCD QDI (15.4WSXGA+)
CARBON S/P
6M.TAXV7.003
LCD MODULE 15.4 IN. COATING
ASSY W/ ANTENNA CCD
ZC1 LCD QDI (15.4WSXGA+)
Pre. S/P
6M.TAXV7.004
LCD 15.4 IN. WSXGA+ QDI
QD15AL02-01 NON GLARE LF
ZC1 15.4 (WSXGA+)
QD15AL02 S/P
LK.15409.014
LCD 15.4 IN.WSXGA+ CMO
N154Z1-L01 NON GLARE LF
ZC1 LCD15.4 WSXGA +
(N154Z1-L01) S/P
LK.1540D.009
LCD 15.4 IN. WSXGA+ SAMSUNG
LTN154P1-L02-V NON GLARE LF
ZC1 LCD15.4 WSXGA +
LTN154P1-L02-V S/P
LK.15406.008
HYNIX SO-DIMM DDRII 533
512MB HYMP564S64P6-C4
ZC1 HYNIX DDRII 533 512MB
RAM S/P
KN.5120G.005
INFINEON SO-DIMM DDRII 533
512MB HYS64T64020HDL-3.7-A
LF (0.11U)
ZC1 INFINEON DDRII 533
512MB RAM S/P
KN.51202.021
NANYA SO-DIMM DDRII533
512MB NT512T64UH8A1FN-37B
LF
ZC1 NANYA DDRII533 512MB
RAM S/P
KN.51203.023
SAMSUNG SO-DIMM DDRII533
512MB M470T6554CZ3-CD500 LF
ZC1 SAMSUNG DDRII533
512MB RAM S/P
KN.5120B.015
NANYA SO-DIMM DDRII667
512MB NT512T64UH8A1FN-3C LF
ZC1 NANYA DDRII667 512MB
RAM S/P
KN.51203.025
NANYA SO-DIMM DDRII533 1GB
NT1GT64UH8A0BN-37B LF
ZC1 NANYA DDRII533 1GB
RAM S/P
KN.1GB03.006
INFINEON SO-DIMM DDRII533
1GB HYS64T128021HDL-3.7-A LF
(0.11u)
SO-DIMM DDRII533 1GB
HYS64T128021HDL-3.7-A LF
(0.11u)
KN.1GB02.023
NANYA SO-DIMM DDRII667 1GB
NT1GT64U8HA0BN-3C LF
SO-DIMM DDRII667 1GB
NT1GT64U8HA0BN-3C LF
KN.1GB03.009
ELPIDA SO-DIMM DDRII533
512MB GU33512AGEPN612C
SO-DIMM DDRII533 512MB
GU33512AGEPN612C
KN.51209.005
MAINBOARD 945PM M56P256MB
SATA W/READER, NEW CARD W/
O CPU MEMORY
ZC1 M/B ASSY S/P
MB.TAX06.001
THERMAL MODULE
ZC1 THERMAL MODULE
ASSY S/P
60.TAXV7.007
SPEAKER
ZC1 SPEAKER
PB2510KN04S-9LB S/P
23.TAXV7.001
SMART CARD READER
ZC1 SMART CARD S/P
60.TAXV7.008
MEMORY
MAIN BOARD
HEATSINK
SPEAKER
N/A
READER
Chapter 6
97
MISCELLANEOUS
N/A
LCD-RUBBER-PAD1ZC1(GAZC1002,REV3A)LF
ZC1 LCD-RUBBER-PAD1 S/P
47.TAXV7.001
LCD-RUBBER-LZC1(GAZC1003,REV3A)LF
ZC1 LCD-RUBBER-L S/P
47.TAXV7.002
LCD-RUBBER-RZC1(GAZC1004,REV3A)LF
ZC1 LCD-RUBBER-R S/P
47.TAXV7.003
CARD-READER-RUBBERZC1(EBZC1040,REV3A)LF
ZC1 CARD READER
RUBBER S/P
47.TAXV7.004
RUBBER FOOT
ZC1 RUBBER FOOT S/P
47.TAXV7.005
SCREW M2.0*2.5-I (NI) (NYLOK)
ET2S SCREW MM2.0X3.0
SPARE PART
86.A03V7.012
SCREW M2.5*6-I (BNI) (NYLOK)
ZG1S I2.5*3M-BNIH(M2.5L3)
S/P
86.T25V7.012
SCREW M2.0*3.0-I-NI-NYLOK
ZI1S SCREW M2.0X5-I-NINYLOK S/P
86.T23V7.006
SCREW M2.0*6.0-I-NI-NYLOK
DT1 SCREW MM25060IL69
SPARE PART
86.A08V7.004
SCREW M2.5*2-I (NI, NYLOK)
ZI1S SCREW M2.5X2-I-NINYLOK S/P
86.T23V7.018
SCREW M2.5*3-I (NI, NYLOK)
ET2S SCREW MM2.5X3.0
SPARE PART
86.A03V7.010
SCREW M2.5*6-I (BNI) TAP
ZC1 SCREW M2.5*6I(BNI)TAP S/P
86.TAXV7.001
SCREW M2.5*4-I (BNI)
ZI1S SCREW M2.5X4-I-BNI S/
P
86.T23V7.019
SCREW M2.5*4.0-I (NYLOK) EU
ZI1S SCREW M2.5X4-INYLOK S/P
86.T23V7.009
SCREWS
N/A
98
Chapter 6
Download PDF

advertising