Acoustic Research AW828 Speaker System User Manual

Introduction
Wireless
Indoor/Outdoor Speaker
With Planter
Setting up the Speaker System
AR’s Wireless Speaker System eliminates the hardest part of adding speakers to your home—
running and hiding hundreds of feet of speaker wire. The AR Wireless Speaker System’s RF
signal travels with ease through walls, floors, ceilings and other obstacles, delivering highquality sound virtually anywhere inside the house or out. With drift- and static-free reception
along with outstanding range—up to 150 feet*—the possibilities for enjoying your AR Wireless
Speaker System are nearly unlimited. The AR Wireless Speaker System is compatible with
most audio sources, such as A/V receivers/amps, stereos, computers, TVs, DVD players, and
portable devices (CD players, cassette players, MP3s etc.). And the removable planter included
with this speaker lets you put your favorite plant right where you hear your favorite music,
with special channels the keep the water from the planter away from the speaker.
This manual covers various connection options and detailed operating instructions for making
the AR Wireless Speaker System a valued part of your lifestyle. If, after having reviewed the
instructions, you have any questions, please call toll-free 1-800-732-6866 or visit
www.araccessories.com.
*Range may vary according to environment.
Tour of the Speaker System
Speaker/Removable Planter
Model AW828
Installation and Operation Manual
Planter
Removable planter holds potted plants or other
decorative items, either in a separate pot or in the
planter itself. Remove it during speaker setup and see
the planter instructions on the other side of this sheet
Battery Compartment Cover remove to install 6 AA
batteries.
Front Panel
Powering the Transmitter
Connect the small, round plug from the
transmitter AC power adapter to the
transmitter’s DC INPUT jack. Plug the other end
of the transmitter AC power adapter into any
standard 120V AC wall outlet.
Note: There is no transmitter ON/OFF switch. The transmitter is designed to be left plugged
in and powered at all times. If you will not be using the AW828 for an extended period of time,
unplug the transmitter AC power adapter.
Connecting to an Audio Source
Connecting to an MP3 player, CD player, or computer
Plug the transmitter’s built-in AUDIO INPUT cable into
headphone output of your MP3 player or CD player (or
audio output jack on your computer).
Warning: This product is designed to work with
line level outputs or headphone outputs only. DO
NOT connect it directly to speaker outputs as it will
Battery
compartment
cover
permanently damage the transmitter.
ON/OFF/TUNE button turns the speaker on and off (push and hold), and tunes the
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user
serviceable parts inside. Refer servicing to qualified service personnel.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
8. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
9. Unplug this apparatus during lightning storms or when unused for long periods of time.
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Care and Maintenance
• Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol or other solvents
as they may damage the surface.
• Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock.
• If the speaker are used outside on a deck or patio, make sure you take them indoors in the event of a rainstorm to
prevent possible damage.
• Do not operate or store the system in extreme temperatures (below 32ºF/0ºC and above 122ºF/50ºC).
•To avoid electrical shock, use this product with caution near water sources if powered with the AC adapter. Never
submerge in water.
speaker to the transmitter if you are having problems linking (push).
POWER indicator turns red when the speaker is first turned on; it turns blue when the
speaker is tuned to the transmitter.
– VOLUME + adjusts the speaker’s volume.
Back Panel
Audio
source
Model No.:______________________________________________________________________________________________
Purchase Date:__________________________________________________________________________________________
Transmitter
(back panel)
Connecting to an A/V Receiver
1. Plug the transmitter’s built-in AUDIO INPUT cable
into a mini-jack to RCA adapter (not included).
2. Connect the stereo plugs on the mini-jack to RCA
adapter to the corresponding left and right audio
outputs of your A/V receiver, amp, or other audio
source.
A/V Receiver
Transmitter
(back panel)
Audio Output
Mini-jack to RCA
adapter (not included)
Back panel door keeps the back panel safe from the
elements when not in use; pull up on the tab on the right
side of the door to access the back panel.
Powering the Speaker
DC IN jack receives the small round end of the included Back panel door
There are two options to power your wireless speaker: using the included AC power adapter or
using 6 AA batteries (not included).
12V 600mA AC power adapter.
L/Mono/R switch determines if the speaker plays sound in mono as a stand-alone speaker,
AC Power Adapters
or plays the left or right track in a stereo pair with an additional AR wireless speaker
1. Insert the small, round plug from the speaker AC
power adapter into the DC IN jack on the back of the
speaker.
Transmitter
Front Panel
2. Plug the other end of the speaker AC power adapter
into any standard 120V AC wall outlet.
POWER indicator lights blue when audio is
present and the transmitter is broadcasting
Note: Be sure to use the speaker AC power adapter
transmission frequency for your environment
DC INPUT jack receives the small round end
of the included 12V 100mA AC power adapter
ANALOG INPUT cable (built in) connects to your sound source using one of the
connection options shown here
Note: These power units
should be plugged in so
that they stay vertical or
lie flat.
Dealer/Address/Phone:___________________________________________________________________________________
Speaker AC/DC 12V
600mA adapter
AC power
adapter
120V AC
wall outlet
Installing Batteries in the Speaker
CHANNEL 1 2 3 lets you find the best
Included
Accessories
Back of the speaker
rated 12V DC 600 mA.
Back Panel
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the
serial and model numbers in case you need them. These numbers are located on the product.
AC Power
Adapter
120V AC
wall outlet
Note: Be sure to use the AC power adapter
rated 12V DC 200 mA (it has the smaller
diameter plug).
Speaker
Important Information
Transmitter
(back panel)
Transmitter AC/DC 12V
100mA adapter
1. Remove the battery compartment cover on the top of the speaker.
2. Insert six (6) AA batteries (not included) into the speaker following the polarity (”+” and “-”)
as diagrammed inside the battery compartment.
3. Replace the battery compartment cover on the top of the speaker.
Note: Keep the door covering the speaker back panel closed when using batteries.
DO NOT mix batteries with different chemistry types (for example, a zinc battery with an alkaline
battery). DO NOT mix new and used batteries. DO NOT leave batteries installed in the product
when not in use for long periods. Always remove old, weak or worn-out batteries promptly and recycle
or dispose of them in accordance with local and national regulations.
Warning: This product is water-resistant, not waterproof. Avoid
prolonged exposure to wet environments, such as rain, mist, dew, etc. In
other words, you can take it out, just don’t leave it out. If you plan to use
the speaker in a humid or wet environment, we recommend powering it with
batteries instead of with the power adapter.
Pairing the Speaker System
Adjusting the Transmitter
1. Turn on your audio source (for example, A/V receiver, MP3
player, stereo, etc.) and play music at a normal listening
volume.
2. Set the channel select switch on the back of the transmitter
to one of the transmitter’s three broadcast frequencies: 1,
2 or 3. If you experience poor reception or interference, try
choosing a different frequency by moving the channel select
switch to another position.
To set up the planter:
Issue:
Cause and solution:
1. Remove the planter from the top of the speaker and take
it to your workbench (or wherever you usually do your
potting). Do not pot the plant while the planter is still on the
speaker!
No sound/
distortion/
static
• Make sure the speaker’s batteries are fresh and inserted with correct polarity (+, –).
Replace if necessary.
Planter
2. Pot the plant as you normally would, either directly in the
planter or in a separate flowerpot (make sure the pot fits in
the planter!).
Channel
select
switch
When the transmitter is receiving an audio signal and is
ready, the POWER indicator on the transmitter’s front panel
turns solid blue.
Note
If the POWER indicator on the transmitter does not turn blue, please check the following:
- Confirm the transmitter AC power adapter is securely connected.
- Confirm the cable from the transmitter is securely connected to the audio source output
(MP3 player, A/V receiver, etc.).
- Confirm the audio source is playing audio and is turned up.
3. Once you’ve finished potting the plant, take it back to the
speaker. Line up the planter’s drainage holes with the slots
on the top of the speaker. Make sure the planter sits on top
of the speaker so that there is no gap between the two.
Transmitter
Speaker
• Omni-directional 900MHz broadcast
• Effective transmitting range:
up to 150 ft. (45m)*
• Phase-locked loop circuitry (PLL)
• 3 selectable broadcast frequencies
•
•
•
•
•
•
•
• Stereo audio input
1. Press and hold the ON/OFF/TUNE button on the front
of the speaker until the POWER indicator turns red.
This indicator light stays red while the speaker is
tuning to the transmitter. The indicator light turns
blue when the speaker is tuned to the transmitter—you
should hear sound coming from the speaker now.
Note: If the speaker is not tuned or if the transmitter is not connected properly, the
indicator light will stay red. If this occurs, please see the troubleshooting section of this
manual.
A fixed-level, or line-level, audio output is considered ideal since it provides an audio signal
unchanged by adjustments to the audio source volume control.
b) Stereo operation: You need an additional AW828 speaker for the stereo option. Set the
L/M/R switch to “L” on the speaker located to the left from the listener, and set the other
speaker to the “R” position.
Notes:
The speaker automatically retunes if it loses the transmitter’s signal. You can also press the ON/
OFF/TUNE button on the front of the speaker to retune the speaker at any time.
The transmitter turns off automatically if there is no audio signal present for a prolonged period.
Interference in the form of static and/or distortion can sometimes be heard. If this occurs,
confirm the transmitter/speaker adjustments and indicators. If the problem persists, refer to the
Troubleshooting section of this manual.
Turning the Speaker Off
1. Press and hold the ON/OFF/TUNE button on the front of the speaker to turn the speaker off.
2. Confirm that the speaker is off by verifying that the indicator light on the speaker’s front
panel is no longer illuminated.
Using the Removable Planter
The removable planter for the AW828 can hold potted plants, either in a separate flowerpot or
in the planter itself. The planter and speaker have special drainage channels that keep water
away from the speaker and let it drain safely out of the bottom of the AW828, so you can keep
your plant watered just as you would with any other planter.
Specifications
use the speaker on a flat, non-carpeted surface.
About Fixed-Level Audio Outputs
a) Monaural operation: The monaural mode (mono) is recommended when using a single
AW828 by itself. For monaural operation, set the L/Mono/R switch to “Mono.”
• Change the location of the transmitter. Place it as high and away from obstructions as
possible. Avoid placing the transmitter directly on top of or behind a TV.
Important: To maintain proper drainage from the planter,
Tuning the Speaker
3. Set up the speaker for mono or stereo operation using the switch on the back of the AW828
speaker.
• Change the position of the channel select switch (1, 2 or 3) to change the operating
frequency. Then press the speaker’s ON/OFF/TUNE button to make the speaker retune.
• Move the transmitter and speaker closer together. Sending the signal through certain
materials, such as glass, tile, and metal, can decrease the effective transmitting
distance of the system.
More Helpful Information
2. Press the – VOLUME + buttons to adjust the volume on the speaker as desired.
• Check that the speaker’s indicator light is blue.
Hint: Fixed-level audio outputs from stereo receivers/amps will typically be designated as
Tape (or Record) outputs or DVR/DVD-R audio output connections.
Fixed-level outputs from TVs are usually marked as ‘Constant,’ ‘Fixed,’ or ‘Select.’ If they are not
marked as such, they are probably variable outputs (see “About Variable-Level Audio Outputs” on
the next page). Outputs from DVD players are almost always fixed.
Hint: When connecting to the audio outputs of a DVD player, remember that the DVD player
must be showing a TV channel for sound to be produced.
About Variable-Level Audio Outputs:
A variable-level output, such as a headphone jack or certain RCA-type outputs, provides an
audio signal that changes with the volume level set on the audio source. As the volume of the
audio source is adjusted up and down, so is the audio signal strength sent to the transmitter.
This can affect the quality of sound generated by the speaker, and may require an adjustment
of the volume level of the audio source to produce a signal strong enough for the transmitter.
Hint: On most bookshelf-type or compact stereo systems, inserting a headphone plug into
the headphone jack results in automatic cutoff of the regular, or hard-wired speakers.
Hint: Most TVs, regardless of age or price, have variable outputs. If you are unsure which
of your TV audio outputs is fixed, refer to the TV instruction manual. Some TVs have
outputs that can switch between variable and fixed. When given a choice, fixed is always
recommended.
Troubleshooting
The following troubleshooting guide takes you through some of the more common problems
associated with the installation and/or operation of a wireless system. If the problem persists,
please call toll-free at 1-800-732-6866 or visit www.araccessories.com.
Issue:
Cause and solution:
No sound
• Check that the transmitter AC power adapter is fully inserted into the wall outlet and the
power cord from the AC adapter is firmly connected to the transmitter power input jack.
• Confirm that the speaker is turned on and tuned to the transmitter—
the indicator light on the front of the speaker should be blue.
• If you’re using the power adapters, confirm that both (for the speaker and for the
transmitter) are fully inserted into their wall outlets and the adapter power cords are
firmly connected to the power input jacks on the transmitter or speaker.
or
• Make sure the speaker’s batteries are fresh and inserted with correct polarity (+, –).
Replace if necessary.
• Check that the audio source component (stereo, MP3 player, etc.) is turned on and
transmitting sound as it normally should.
• Make sure the volume on your audio source is turned up.
• Check that the speaker volume is turned up.
• If you are using a Tape 2 Monitor output from your receiver/amp as the audio output,
check that you have pressed the Tape Monitor/Tape 2 button on the front of the receiver.
This will turn on the Tape 2 outputs, which may not have been active.
*Maximum range; results may vary according to
environment.
Push-button, auto-lock tuning
5” full-range speaker driver
5 Watt RMS internal amplifier
Omni-directional sound
Frequency response: 20Hz - 20kHz
Left/Mono/Right switch
Operates using supplied AC adapter or six (6) AA
batteries (not included)
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Regulations state that unauthorized changes or modifications to this equipment may void the user’s authority to
operate it.
Industry Canada Regulatory Information
Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause undesired operation. The user is cautioned
that this device should be used only as specified within this manual to meet RF exposure requirements. Use of this device
in a manner inconsistent with this manual could lead to excessive RF exposure conditions.
This Class B digital apparatus complies with Canadian ICES-003.
12 Month Limited Warranty
Audiovox Electronics Corporation (the “Company”) warrants to the original retail purchaser of this product that
should this product or any part thereof, under normal use and conditions, be proven defective in material or
workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced
(at the Company’s option) without charge for parts and repair labor. To obtain repair or replacement within
the terms of this Warranty, the product along with any accessories included in the original packaging is to be
delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation
prepaid, to the Company at the address shown below. Do not return this product to the Retailer.
This Warranty is not transferable and does not cover product purchased, serviced or used outside the United
States or Canada. The warranty does not extend to the elimination of externally generated static or noise, to
costs incurred for the installation, removal or reinstallation of the product.
The warranty does not apply to any product or part thereof which, in the opinion of the company, has suffered or
been damaged through alteration, improper installation, mishandling, misuse, neglect, accident or exposure to
moisture. This warranty does not apply to damage caused by an AC adapter not provided with the product, or by
leaving non-rechargeable batteries in the product while plugged into an AC outlet.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED TO DURATION OF THIS WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER,
INCLUDING ANY IMPLIED WARRANTY, MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM THE DATE
OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES WHATSOEVER. No person or representative is authorized to assume for the Company
any liability other than expressed herein in connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you.
This Warranty gives you specific legal rights and you may also have other rights which vary from state/province
to state/province.
U.S.A.:Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, Unit #3 Door 16, Mississauga Ontario L5T
3A5
Trademark(s) ® Registered
www.araccessories.com
MADE IN CHINA
AW828 US IB 00