Instruction manual | Acu-Rite 954 Postal Equipment User Manual

Instruction Manual
Digital Pocket Scale
model 00954
CONTENTS
Package Contents................... 2
Customer Support................... 2
Features & Benefits.................. 3
Setup..................................... 4
Install or Replace Battery......... 4
Using the Scale....................... 5
Troubleshooting...................... 7
Care & Maintenance............... 7
Specifications.......................... 7
Questions? Contact Customer Support at
(877) 221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Package Contents
1. Scale
2. Cover
3. Instruction Manual
Customer Support
AcuRite customer support is committed to providing you with best-inclass service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(877) 221-1252
info@chaney-inst.com
24/7 support at www.AcuRite.com
► Installation
Videos
► Register
your Product
► Instruction
Manuals
► Support
User Forum
► Replacement
Parts
► Submit
2
Feedback & Ideas
Features & Benefits
TOP
1 2 3 4 5
TOP
1. ON/OFF Button
2.Display
3. ZERO/TARE Button
4. Weighing Area
5. UNIT Button
Toggle measurement
units between grams (g),
ounces (oz), pennyweight
(dwt), troy ounces (oz t),
and piece count.
BACK
7
BACK
6
6. Battery Compartment
Cover
7. Battery Compartment
DISPLAY
DISPLAY
8
9
10
11
8. Piece Count Indicator
9. Tare Indicator
10.Current Weight
11. Weight Units
12 Ounces (OZ)
12.Weight Units
Grams (g)
13.Minus Indicator
Weight of item(s) removed
from scale.
14.Zero Indicator
15.Weight Units
Pennyweight (d)
(1dwt=1.56g=0.054oz)
13
14
15
3
16
16.Weight Units
Troy Ounce (t)
(1oz t=31.1g=1.097oz)
SETUP
Install or Replace Battery
1. R
emove the battery compartment cover.
2. Insert 2 AAA alkaline batteries into the battery compartment, as shown.
Follow the polarity (+/-) diagram in the battery compartment.
3. R
eplace the battery cover.
2
1
Install Battery
2 AAA alkaline
batteries
Remove
Battery Cover
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.
4
OPERATION
Using the Scale
Remove the cover from the top
of the scale by lifting it from
one side. Cover may be used
to weigh items on the scale
(optional).
Measure Weight
1.Place the scale on a flat, stable surface.
2.Press the "ON/OFF" button to power the scale ON.
3.Wait for the display to show "0.00".
4.Press the "UNIT" button to select your preferred measurement units.
Measurement units include: GRAMS, OUNCES, PENNYWEIGHT, TROY
OUNCES, and PIECE COUNT.
5.Place item(s) to be weighed on the center of the scale.
6.Weight will be shown on the display. Press the "UNIT" Button to convert
the measurement units between grams (g), ounces (OZ), dwt (d), oz t (t)
and piece counting mode (See below).
Piece Counting Mode
When Piece Counting Mode is selected, "PCS" will show on the display. To use
Piece Counting Mode you must first calibrate the scale to an item. Next, you
can place any amount of that same item on the scale and the scale will display
the quantity (pieces) of that item.
Calibrate the Scale to an Item
1.Place the scale on a flat, stable surface.
2.Press the "ON/OFF" button to power the scale ON.
3.Press the "UNIT" button to select Piece Counting Mode ("PCS" is shown
on the display).
4.Press and HOLD the "UNIT" button for 3 seconds to select 25, 50 or 100
pieces. When a quantity has been chosen, place that same number of
items on the weighing platform.
5.The quantity selected will flash on the display. The display stops flashing
when the scale has determined the weight of the items.
6.Weight will be shown on the display.
Determine the Quantity (Pieces) of an Item
1.Press the "ON/OFF" button to power the scale ON (if applicable).
2. Place any quantity of the item the scale has been calibrated to in the
steps above on the scale.
Continued on page 6.
5
3.Weight will be shown on the display.
4.Press the "UNIT" button until "PCS" is indicated on the display.
5.Quantity of items placed on the scale will be shown on the display.
Please Note: To determine the quantity of a different item than the item the
scale has been calibrated to, repeat the steps in "Calibrate the Scale to an
Item" (page 5).
Zero & Tare Functions
To measure items as they are added, use the Zero and Tare Functions. If the
weight of the items being measured is below 4% of the scale’s capacity (less
than 8 g/0.282192 oz), the Zero function is used. If the weight of the items
exceeds 4% of the scale’s capacity, the Tare function is used.
1.Place item(s) on the center of the scale.
2. Weight will be shown on the display.
3.Without removing the item(s), press "Z/T" button to reset display to
"0:00".
4.Depending on the weight of the item(s), you will see the Zero indicator
"O" or the Tare indicator "TARE" on the display.
5.With the first item(s) still in place, add the next item to the scale. The
display will now show the weight of that item.
6.Press "Z/T" button to view the combined weight of the two items.
7.Press "Z/T" button again to reset the display to "0:00".
8.Repeat these steps (5-7) until all items have been added.
Minus Function
If you add multiple items to the scale at one time to get a total weight, you can
measure the weight of a single item or ingredient by using the Minus Function:
1.Add item(s) to the scale.
2.Total weight will be shown on the display.
3.Press "Z/T" button to reset the display to "0:00".
4.Remove an item.
5.Value shown on the display with the with the Minus Function indicator (–)
indicates the weight of the removed item.
6.Press "Z/T" button to view the total weight of any remaining items on the
scale.
7.Repeat these steps (4-6) as needed.
Momentary Backlight
The display's momentary backlight will turn on when the scale is powered on.
Backlight turns off after 30 seconds of inactivity. Backlight turns on again while
scale is in use.
6
Warning Messages
Replace battery (see page 4).
Maximum capacity has been exceeded. Remove
items to prevent damage.
Power the Unit ON/OFF
The scale will automatically power off when the display shows "0:00" or the
same weight for 2 minutes. Press "ON/OFF" to manually power the scale ON
or OFF.
Storage
The scale should be stored in a cool dry place.
Troubleshooting
Problem
Display screen
not working
Possible Solution
•C
heck that the batteries are installed correctly.
Batteries may need to be replaced.
If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
(877) 221-1252 for assistance.
Care & Maintenance
Store in a dry location at room temperature. Clean with a soft, damp cloth.
DO NOT immerse in water or use caustic cleaners or abrasives. All parts
should be wiped clean immediately after direct contact with foods. Use the
scale on a hard, flat surface. DO NOT strike, shake or drop the scale. Scale is
not designed for commercial use.
Specifications
MAX WEIGHT CAPACITY
200 g / 7 oz / 128 dwt / 6 ozt
POWER
2 x AAA alkaline batteries
7
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
It’s more than accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
Printed in China
00954 INST 010314
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark
of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and
copyrights are the property of their respective owners. AcuRite uses patented
technology. Visit www.AcuRite.com/patents for details.
Download PDF

advertising