Instruction manual | Acu-Rite 972 Marine Radio User Manual

00972 INST0518-06
Instruction Manual
Wireless Weather Station
& Atomic Clock
MODEL # 00972
Wireless Sensor
Main Unit
THERMO HYGRO
with low
temperature
adaptor
Thank You! We appreciate you for purchasing the new generation radio-controlled
wireless weather station and atomic clock. This instrument is designed and engineered
with state-of-the-art technology and components. It will provide these accurate and
reliable measurements: date, time, and indoor/outdoor temperatures and humidity levels.
1 CHECK PACKAGE CONTENTS
(1) Main Unit – 7.25” x 2.75” x 1.5”*
(1) Wireless Sensor – dimensions: 2.5" x 3.5" x 1"*
(1) 10’* wired low temperature adaptor
(2) 1” (2.5cm) screws with plastic anchors
(1) Instruction manual
* dimensions approximate
2 READ
Please read this entire manual carefully before you set up the instrument and begin to
use it. In this way you can become familiar with the features of the weather station &
clock to get the most benefit from it.
1
3 INSTALL BATTERIES
Main Unit: Always install batteries into the main unit first. On the back of the unit,
remove the battery compartment cover. Insert 2 AA alkaline (or lithium – See NOTES
below) batteries. Replace the cover.
Main Unit
BACK
1
Wireless Sensor: After batteries have been put into the main unit, remove the 4 screws
to remove the back cover of the wireless sensor. Insert 2 AA alkaline (or lithium)
batteries. Press the “TX” button and replace the back cover and the 4 screws on the
sensor. Put the sensor aside for now, and continue to learn about the main unit. Later, in
part 5 of this manual you’ll learn more about the wireless sensor.
2
NOTE: When replacing the batteries for the wireless sensor, remove the batteries from
the sensor and clear the sensor’s channel on the main unit by pressing and holding the
CHANNEL button when the corresponding channel is displayed. Reinstall the batteries
into the wireless sensor and press and release the TX button to synchronize the units.
Operating Range of Batteries
LITHIUM
BATTERIES
ALKALINE
BATTERIES
-22ºF (-30ºC)
-4ºF (-20ºC)
(70ºC)
158ºF
(70ºC)
158ºF
AA
Remove Battery
Compartment Cover
AA
Severe cold (below -4º F/-20º C) can cause alkaline
batteries to freeze and function improperly. Use lithium
batteries in extremely low temperature conditions to
ensure continued operation.
Low Battery Indicator:
When the battery level is low for the main unit or the wireless sensor, the
low battery level icons will illuminate.
Wireless Sensor
BACK
4 CHOOSE WHERE TO PLACE THE MAIN UNIT and WIRELESS SENSOR
Main Unit: Choose wall mount or table-top placement.
• Choose a location for each unit that is at least 10 feet away from other electronic
devices that may interfere with the wireless signal.
• Wall mounting: Use the mounting slot on the back of the unit to hang it from one of the
supplied screws.
• Table-top placement: Fold out the integrated table-top stands to place the main unit
on a table-top surface.
Wireless Sensor: When placing the sensor, consider these things:
• Although the sensor is designed for outdoor use, placement in a protected area will
prolong its life.
• Mounting: Use the mounting slot on the back of the unit to hang it from one of the
supplied screws.
• The sensor must be within 100 feet (30 meters) of the main unit.
• The sensor is resistant to weather and to water. It is NOT WATERPROOF.
• Prolonged exposure to cold weather may cause damage to the LCD panel.
• Wireless sensor can be placed outdoors to observe outdoor temperatures and
humidity.
AA
TX C/F MODE 1 2 3
2
AA
AA
AA
1
REMOVE 4 SCREWS
TO OPEN BATTERY
COMPARTMENT
Placement
RF WIRELESS
2
3
MAIN UNIT FUNCTION BUTTONS
Using the included LOW TEMPERATURE ADAPTOR
The wireless sensor will operate normally down to -4 ºF. Below -4 ºF, the electronics
may operate erratically or become non-functional until the temperature raises again.
In case temperatures fall below -4ºF, bring the wireless sensor indoors and use the
included low temperature adaptor by running the wire out through a soft seal opening
such as a window or door. When routing the wire for the low temperature adaptor,
make certain that the wire will not be severed or damaged.
( top of main unit )
Wireless Sensor is
protected indoors in
extreme temperatures
5 PREVIEW THE DISPLAYS
Trend Indicators
Calendar Sets Itself
Clock Sets Itself
Function Buttons
Wireless Sensor is
weather-resistant and
can be placed outdoors
EXTREMELY LOW
TEMPERATURES
NORMAL
TEMPERATURES
INDOOR
Atomic Clock Signal
low-temp adaptor
is used outside to
observe temperature
OUTDOOR
LOW-TEMP.
ADAPTOR
EXTREMELY LOW
TEMPERATURES
-4 ºF
OR LOWER
WIRELESS
SENSOR
LOW-TEMP.
SENSOR
NOTE: The wired TEMPERATURE ADAPTOR only observes temperature, not humidity.
If the adaptor is placed outdoors, and the wireless sensor is indoors- the wireless
sensor will only transmit the indoor humidity reading & the outdoor temp. reading.
4
Indoor Temperature Outdoor Temperature
and Humidity
and Humidity
Moon Phase
Low Battery
Indicator
Wireless Sensor Display
Press the “MODE” button inside the back of the wireless sensor to display temperature
and/or humidity in one of three ways:
1)Temperature continuously,
2)Humidity continuously, or
3)Temperature for 5 seconds, then humidity for 5 seconds
NOTE: The sensor’s display setting does not affect the main unit’s display.
Channel
(sensor #)
1
86.5
F
Display Mode 1
(Temperature)
press
“mode”
button
1
25
Display Mode 2
(Humidity)
5
press
“mode”
button
86.5
1
25
1
F
(Alternate icon)
Display Mode 3
(alternating temp. & Humidity)
7 MAIN UNIT FEATURES
MAIN UNIT
Operation buttons are located on the front and back of the main unit
6 UNDERSTAND WHAT THE BUTTONS DO.
BUTTON NAME
PRESS & RELEASE
PRESS & HOLD
FOR 3 SECONDS
CH (CHANNEL)
choose channel 1,2,
or 3
clears the current
channel
MEMORY
(min/max)
read maximum &
minimum values for
temperatures,
humidity (both
indoor & outdoor)
N/A
ALARM
view alarm time for
5 seconds
set alarm time
SET
starts radio
controlled time
synchronization
to set clock &
calander manually
+
turn alarm on/off
OR
raise a setting by
one unit
fast advance
setting mode
- C/F
zone
select ºC or ºF
OR
lower a setting by
one unit
fast reverse in time
setting mode &
current time zone
setting
-or-
N/A
WIRELESS SENSOR
activate
backlight for
low-light
viewing
BUTTON NAME
PRESS & RELEASE
TX
sends wireless
signal to main unit
C/F
select ºC or ºF
display mode
for wireless sensor
Mode
choose display
mode for wireless
sensor
CH (1,2or 3)
choose channel 1, 2,
or 3
6
Manually Setting the Time and Date:
1) Press and hold the “SET” button, and the year display will flash on the screen. Using
the “+” and “– ” buttons set the year. When the correct year is entered, press and
release the “SET” button to confirm the setting.
2) Once you have confirmed the year, follow the same procedure to set the month, date,
hour, minute, 12 or 24-hour time preference, and DST (Daylight Saving Time).
NOTE: You cannot change any settings manually if the clock is attempting to synchronize. Allow the clock to finish the cycle, and then manual changes can be made if the
clock has not automatically acquired the signal and set itself to the correct time.
Time Zone:
Note: Default setting is Pacific Time. If you live outside of the Pacific Time Zone, you will
need to set your Time Zone using the following procedure:
1) Press and hold the “– / C/F” button on the front of the clock for three seconds. The
area of the clock where the seconds are usually displayed will be replaced with the letter
for the time zone it is currently set in.
2) If set to the default setting, you will see a flashing letter “P” on the screen after
pressing and holding the “– / C/F” button. Press and release the “– / C/F” button until
the letter shown corresponds to your time zone:
P = Pacific
silence the alarm
for 5 minutes
SNOOZE / LIGHT
Radio-controlled Clock : The unit starts synchronizing the clock after the 1st channel
of the wireless sensor begins to send its information to the main unit. (This is called
registration.) The built-in antenna receives the official time signal from the US
Government's National Institute of Standards and Technology. A microchip translates
the time signal and adjusts the time display for the correct time, and date.
M = Mountain
C = Central
E = Eastern
Once your zone is displayed, there is nothing more you need to do. After about 3
seconds, the seconds will once again be displayed on your clock.
The antenna icon ( ) will flash on and off during synchronization. If the icon disappears, this indicates that the radio signal is not available. If you are unable to obtain a
signal after a long period of time, try placing the base unit away from sources of
interference such as computers, televisions, cordless phone bases, and other electronic
items.
TX C/F MODE
123
AA
AA
Note: The synchronization process can take 24-72 hours.
Celsius/Fahrenheit:
Press and release the “–” (minus) button. A beep sounds, and the display will change to
either Fahrenheit or Celsius.
3 buttons & slide
switch Inside BACK
of remote sensor
case
7
Moon Phase:
The moon phase will automatically display based on the calender date. The moon phase
display will scroll from left to right, and pause for about 5 seconds to display the current
moon phase. NOTE: the moon phase will not be correct unless the date and year are
programmed correctly.
OTHER ADJUSTMENTS
Trend Indicators:
Arrow icons in the upper display will indicate the following trends:
Rising
Steady
8 MULTIPLE WIRELESS SENSORS
The main unit supports up to three wireless sensors. Each additional wireless sensor
must be designated a different channel number. Assigning different channel numbers
differentiate each sensors temperature and hygrometer readings for the main units’
display.
Additional wireless sensors are sold separately. Call 1-800-556-2548 to order.
WIRELESS SENSOR MODEL # 01022
Falling
The arrow icons will indicate rising, steady or falling if the temperature or humidity
change is more than 1 unit (degree/percent) within an hour.
SETTING THE ALARM:
1) Hold “ALARM” for 3 seconds.
2) The hour number(s) flash. Press “+” or “-” to enter the desired hour. Press
“ALARM” to confirm the hour setting.
3) The minute number(s) flash. Press “+” or “-” to enter the desired minute.
Press “ALARM” to confirm the minute setting.
To view the alarm time, press the “ALARM” button during the normal operating mode.
Alarm time will display for five seconds. Then, the current time is displayed.
To Turn the Alarm On and Off: Press the “+” button during the normal operating
mode. The bell (alarm) icon will show if the alarm is set and activated.
To Turn off the Alarm for One Day: To turn the alarm off for one day, press the
“ALARM” button when the alarm sounds
Snooze/Light:
When the alarm sounds, press the “SNOOZE/LIGHT” button to trigger the snooze
feature. The alarm is silenced for five minutes. Then, it will sound an alarm again.
The “SNOOOZE/LIGHT” button also activates the built-in backlight for 5 seconds.
1) Open each sensor by removing the 4 screws and the cover.
2) Install batteries, see section 3.
3) Use the interior slide switch to select a channel – 1, 2, or 3.
4) Choose Celsius or Fahrenheit with the C/F button, for the sensor display.
5) With the “MODE” button choose what you want the sensor display to show:
Temperature only,
Humidity only, or
Temperature and humidity, alternating.
6) Press the “TX” button to send a signal to the base station.
7) Replace the cover and the 4 screws.
8) Mount the sensor. See section 4 for placement of the wireless sensor unit.
9 PRODUCT SPECIFICATIONS
MEASUREMENT RANGE:
Indoor main unit
:
Outdoor/Indoor humidity :
Wireless sensor
:
with low-temp adaptor :
Barometer
Channel
:
Transmission
:
Resolution
:
mb for
Clock
:
Batteries
:
for
MODEL#00592W
0º C to + 50º C (+32º F to +122º F)
20% - 99% RH
-20º C to +70º C (-4º F to +158º F)
-30º C to +70º C (-22ºF to +158º F)
:
900 to 1050 mb/hPa
maximum of three wireless sensors
up to 30M (100 ft.) open area, RF434 MHz
0.1º for temperature, 1% for humidity, 1 hPa
pressure
WWVB radio-controlled, quartz back-up
AA x 2 alkaline for main unit; AA x 2 alkaline
wireless sensor
MIN / MAX MEMORY:
Press the “MEMORY” button to view the maximum values (Inside/Outside Temperature and Humidity) for 5 seconds. Press the “MEMORY” button again to view the
minimum memory.
The memory will automatically refresh every 24 hours.
8
9
Download PDF

advertising