Instruction manual | ADC AD-310 Clothes Dryer User Manual

PUB.DIM-519
Digital Video Camcorder
English
Instruction Manual
Camescope vidéo numérique
Manuel d’instruction
Videocámara digital
Manual de Instrucciones
Mini
Français
Español
Digital
Video
Cassette
This instruction manual covers the ZR70 MC, ZR65 MC and ZR60. Please note that
illustrations and explanation in this manual are based on the ZR70 MC.
Ce manuel d’instruction traite des modèles ZR70 MC, ZR65 MC et ZR60. Veuillez
noter que les illustrations et les explications contenues dans ce manuel sont basées
sur le ZR70 MC.
Este manual de instrucciones cubre la ZR70 MC, la ZR65 MC, y la ZR60. Tenga en
cuenta que las ilustraciones y las explicaciones de este manual se basan en la
ZR70 MC.
NTSC
Important Usage Instructions
E
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
Introduction
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
COPYRIGHT WARNING:
Unauthorized recording of copyrighted materials may infringe on the rights of
copyright owners and be contrary to copyright laws.
Digital Video Camcorder, ZR70 MC/ZR65 MC/ZR60 systems
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and use in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
Important Warning
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
2
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point, within an
equilateral triangle, is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the product.
IMPORTANT SAFETY INSTRUCTIONS
In these safety instructions the word “product”
refers to the Canon Digital Video Camcorder
ZR70 MC/ZR65 MC/ZR60 A and all its
accessories.
1. Read Instructions — All the safety and
operating instructions should be read
before the product is operated.
2. Retain Instructions — The safety and
operating instructions should be retained
for future reference.
4. Follow Instructions — All operating and
maintenance instructions should be
followed.
5. Cleaning — Unplug this product from the
wall outlet before cleaning. Do not use
liquid or aerosol cleaners. The product
should be cleaned only as recommended in
this manual.
6. Accessories — Do not use accessories not
recommended in this manual as they may
be hazardous.
7. Avoid magnetic or electric fields — Do not
use the camera close to TV transmitters,
portable communication devices or other
sources of electric or magnetic radiation.
They may cause picture interference, or
permanently damage the camera.
8. Water and Moisture — Hazard of electric
shock — Do not use this product near
water or in rainy/moist situations.
9. Placing or Moving — Do not place on an
unstable cart, stand, tripod, bracket or
table. The product may fall, causing serious
injury to a child or adult,
and serious damage to the
product.
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
11. Polarization — The CA-570 Compact Power
Adapter is equipped with a polarized 2prong plug (a plug having one blade wider
than the other).
The 2-prong polarized plug will fit into the
power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug.
If the plug still fails to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the
polarized plug.
E
Introduction
3. Heed Warnings — All warnings on the
product and in the operating instructions
should be adhered to.
10. Power Sources — The CA-570 Compact
Power Adapter should be operated only
from the type of power source indicated on
the marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
company. Regarding other power sources
such as battery power, refer to instructions
in this manual.
12. Power Cord Protection — Power cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them. Pay particular
attention to plugs and the point from
which the cords exit the product.
13. Outdoor Antenna Grounding — If an
outside antenna is connected to the
product, be sure the antenna is grounded
so as to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code,
ANSI / NFPA No. 70—1984, provides
information with respect to proper
grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, connection to grounding
electrodes, and requirements for the
grounding electrode. See figure 1.
3
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
Fig. 1
ANTENNA
LEAD IN
WIRE
E
GROUND
CLAMP
ANTENNA
DISCHARGE
UNIT
(NEC SECTION
810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Introduction
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE
GROUNDING ELECTRODE
SYSTEM
(NEC ART 250. PART H)
14. Lightning — For added protection of this
product during a lightning storm, or when
it is left unattended and unused for long
periods of time, disconnect it from the wall
outlet and disconnect the antenna. This will
prevent damage to the product due to
lightning and power-line surges.
15. Overloading — Do not overload wall outlets
and extension cords as this can result in a
risk of fire or electric shock.
16. Objects and Liquid Entry — Never push
objects of any kind into this product
through openings as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Be careful not to spill liquid of any kind
onto the product.
17. Servicing — Do not attempt to service this
product yourself as opening or removing
covers may expose you to dangerous
voltage or other hazards. Refer all servicing
to qualified service personnel.
18. Damage Requiring Service — Disconnect
this product from the wall outlet and all
power sources including battery, and refer
servicing to qualified service personnel
under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If any liquid has been spilled onto, or
objects have fallen into, the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
even if you follow the operating
instructions. Adjust only those controls
that are covered by the operation
instructions. Improper adjustment of
other controls may result in damage and
will often require extensive work by a
qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
f. When the product exhibits a distinct
change in performance. This indicates a
need for service.
19. Replacement Parts — When replacement
parts are required, be sure the service
technician has used replacement parts that
are specified by Canon or that have the
same characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock or other hazards.
20. Safety Check — Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in safe
operating order.
When replacement of power supply is required, please return it to the
responsible nearest Canon Service Center and please replace it with the same
type number CA-570.
The Adapter can be used with a power supply between 100 and 240 V AC.
For areas where 120 V AC power is not used, you will need a special plug
adapter. Contact your nearest Canon Service Center for further information.
4
Reference Guide
The following manuals are supplied with the camcorder:
E
❍ Digital Video Camcorder ZR70 MC/ZR65 MC/ZR60 Instruction Manual
This manual explains the camcorder operations from basic video recording to the
use of the full range of features.
Introduction
❍ Windows XP Users Only
DV NETWORK SOLUTION DISK Software Instruction Manual
This manual explains how to download/upload images from/to the memory card
using a DV (IEEE1394) cable. You can also perform videoconference and file transfer
over the Internet using the provided software. Available functions depend upon
the camcorder model and networking environment.
❍ ZR70 MC ZR65 MC
DIGITAL VIDEO SOLUTION DISK Software Instruction Manual
This manual explains how to download images from the memory card to a
computer using the supplied USB cable. You can add sample images for Card Mix
and My Camera settings from the supplied DIGITAL VIDEO SOLUTION DISK.
Trademark Acknowledgements
• Canon is a registered trademark of Canon Inc.
• D is a trademark.
•
logo is a trademark.
• Macintosh is a trademark of Apple Computer Inc., registered in the United States
and other countries.
• Windows® is either a registered trademark or trademark of Microsoft Corporation in
the United States and/or other countries.
• Other names and products not mentioned above may be registered trademarks or
trademarks of their respective companies.
5
Table of Contents
E
Introduction
Reference Guide ..............................................................................................................5
Thank You for Choosing a Canon ................................................................................9
Introducing the ZR70 MC/ZR65 MC/ZR60 ..................................................................10
Components Guide ......................................................................................................11
Introduction
Mastering the Basics
Preparations
Using a Household Power Source ..............................................................................15
Attaching and Charging the Battery Pack ................................................................16
Installing the Backup Battery ......................................................................................19
Preparing the Camcorder ............................................................................................20
Loading a Cassette ........................................................................................................22
Using the Wireless Controller......................................................................................24
Setting the Time Zone, Date and Time......................................................................25
Basic Recording
Recording Movies on a Tape ......................................................................................28
Zooming ........................................................................................................................30
Using the LCD Screen....................................................................................................32
Searching and Reviewing when Recording ..............................................................35
Tips for Making Better Videos ....................................................................................36
Basic Playback
Playing Back a Tape ......................................................................................................37
Playing Back on a TV Screen........................................................................................41
Using the Full Range of Features
General
Menus and Settings ......................................................................................................44
Changing the Remote Sensor Mode ..........................................................................49
Customizing the Camcorder ........................................................................................50
ZR70 MC Setting the Light-up Buttons ........................................................................51
Other Camcorder Settings ..........................................................................................52
Recording
Changing the Recording Mode (SP/LP) ......................................................................54
Recording Still Images on a Tape................................................................................55
Using the Recording Programs....................................................................................57
Using Digital Effects......................................................................................................61
Using the Multi-Image Screen ....................................................................................67
Turning Off the Image Stabilizer ................................................................................69
Recording With the Self-Timer....................................................................................70
Audio Recording ..........................................................................................................71
ZR70 MC Using the VL-3 Video Light (Optional) ........................................................73
ZR70 MC Using the DM-50 Microphone (Optional)....................................................74
Manual Adjustments
Adjusting the Focus Manually ....................................................................................75
6
Adjusting the AE Shift ..................................................................................................77
Setting the Shutter Speed............................................................................................78
Setting the White Balance ..........................................................................................80
Playback
Magnifying the Image..................................................................................................82
Displaying the Data Code ............................................................................................83
Photo Search/Date Search............................................................................................85
Returning to a Pre-marked Position ..........................................................................86
E
Editing
ZR70 MC ZR65 MC
Using a Memory Card
Introduction
Recording to a VCR or Digital Video Device ............................................................87
Recording from Analog Video Devices (VCR, TV or Camcorder) ..........................89
Recording from Digital Video Devices (DV Dubbing)..............................................90
Converting Analog Signals into Digital Signals (Analog-Digital Converter) ........92
Replacing Existing Scenes (AV Insert) ........................................................................94
Audio Dubbing..............................................................................................................96
Connecting to a Computer Using a DV (IEEE1394) Cable ......................................99
Inserting and Removing the Memory Card ............................................................100
Selecting the Image Quality/Size ..............................................................................101
Recording Still Images on a Memory Card..............................................................104
Recording Panoramic Images (Stitch Assist Mode) ................................................107
ZR70 MC Recording Motion JPEG Movies on a Memory Card................................109
Playing Back a Memory Card ....................................................................................111
Protecting Images ......................................................................................................114
Erasing Images ............................................................................................................115
Selecting Still Images for Printing (Print Order) ....................................................116
Printing with the Direct Print Function....................................................................118
Combining Images (Card Mix) ..................................................................................122
Copying Still Images....................................................................................................126
Formatting a Memory Card ......................................................................................128
Connecting to a Computer Using a USB Cable ......................................................129
Creating a Start-up Image ........................................................................................130
Memory Card Information ........................................................................................131
Additional Information
Screen Displays ............................................................................................................134
List of Messages ..........................................................................................................138
Maintenance................................................................................................................141
Troubleshooting ..........................................................................................................145
System Diagram ..........................................................................................................148
Optional Accessories ..................................................................................................149
Specifications ..............................................................................................................152
Index ............................................................................................................................154
7
Conventions Used in This Manual
Operating Modes
E
Operating Mode
Position of the
POWER Switch
Position of the
TAPE/CARD Switch
CAMERA
CAMERA
PLAY (VCR)
PLAY (VCR)
TAPE
TAPE
CARD CAMERA
CAMERA
CARD
CARD PLAY (VCR)
PLAY (VCR)
CARD
Introduction
Shaded area : ZR70 MC and ZR65 MC only.
Available functions depend upon the operating mode. It is indicated as follows:
CAMERA
: Function can be used in this mode.
CAMERA
: Function cannot be used in this mode.
Other Symbols and References
❍
: Reference page number.
❍
: Functions to be operated on the body of the camcorder.
❍
: Functions to be operated on the wireless controller.
❍
: Additional topics that complement the basic operating procedures.
❍
: Precautions related to the camcorder operation.
❍ Capital letters are used to refer to buttons on the camcorder or the wireless
controller.
❍ [ ] are used to refer to menu items displayed on the screen.
❍ “Screen” refers to the LCD and the viewfinder screen.
The serial number of this product can be found at the battery attachment unit of
the camcorder. Write down the number and other information here and retain this
book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase:
Model Name: ZR70 MC/ZR65 MC/ZR60
Purchased From:
Serial No.:
Dealer Address:
Dealer Phone No.:
8
Thank You for Choosing a Canon
The Canon ZR70 MC/ZR65 MC/ZR60 provides a full range of options and functions. We
recommend reading this manual thoroughly before you use the camcorder. It will help
you to become more familiar with your camcorder, and learn how to operate it
E
properly.
We suggest that you master the basic operations of the camcorder first, before
moving on to its full range of features.
Checking Supplied Accessories
Two AA Batteries
Lens Cap and Lens
Cap Cord
SS-800 Shoulder Strap
Lithium Button
Battery CR1616
ZR70 MC BP-512
Battery Pack,
CA-570 Compact
Power Adapter (incl.
power cord)
ZR70 MC WA-30.5
Wide Attachment
ZR65 MC
ZR60
Introduction
ZR70 MC ZR65 MC
WL-D79 Wireless Controller,
ZR60 WL-D80 Wireless
Controller
BP-508 Battery Pack
STV-250N Stereo
Video Cable
ZR70 MC ZR65 MC
ZR70 MC ZR65 MC
IFC-300PCU USB Cable SDC-8M SD Memory
Card (containing
sample images)
ZR70 MC ZR65 MC
Hard Case for SD
Memory Card
DV NETWORK
SOLUTION DISK
ZR70 MC ZR65 MC
DIGITAL VIDEO
SOLUTION DISK
9
Introducing the ZR70 MC/ZR65 MC/ZR60
E
22× Optical and
440× Digital Zoom (ZR70 MC)
20× Optical and
400× Digital Zoom (ZR65 MC)
Introduction
18× Optical and
360× Digital Zoom (ZR60)
Image Stabilizer
Stabilizes your recordings even in long
telephoto shots (in Camera mode).
Night Mode
Allows recording even in dark places.
The Night mode adjusts automatically to
the optimum shutter speed.
Super Night Mode and
Low Light Plus Mode (ZR70 MC)
With the ZR70 MC’s Super Night mode
(in Camera mode) and Low Light Plus
mode (in Card Camera mode), you can
keep on shooting without turning the
lights on. The assist lamp (White LED)
lights up to illuminate the subject.
Still Images
Just press the photo button to capture
still images like photographs.
My Camera Settings
You can personalize your camcorder by
customizing the start-up image and
camcorder sounds.
Analog Line-in Recording/
Audio Dubbing/AV Insert Editing
10
Advanced Accessory Shoe
(ZR70 MC)
Simply slide Canon’s DM-50 Directional
Stereo Microphone or VL-3 Video Light
into the accessory shoe; the camcorder
will automatically provide power and
connections.
Digital Effects
Show your creativity by using the special
effects and faders. The multi-image
screen captures moving subjects in 4, 9 or
16 sequences of still images.
Memory Card (ZR70 MC/ZR65 MC)
You can record images on a SD Memory
Card or MultiMediaCard. Images
recorded in Stitch Assist mode can be
merged into one panoramic scene with
the supplied software.
Direct Print (ZR70 MC/ZR65 MC)
You can print still images by connecting
to a Canon Bubble Jet Printer with Direct
Print function.
USB Terminal (ZR70 MC/ZR65 MC)
Allows transfer of memory card data to a
computer with built-in USB port. You can
organize and edit images on your
computer using the supplied software.
IEEE1394 DV Terminal
The DV terminal allows high-quality
transfer with virtually no deterioration in
quality of images. You can edit images
by connecting the camcorder to a PC
with IEEE1394 terminal. Windows XP
Users can use the supplied software to
perform videoconference and file
transfer over the Internet.
Components Guide
ZR70 MC/ZR65 MC/ZR60
E
REC SEARCH + button (p. 35) /
(fast forward) button (p. 37) /
CARD + button* (p. 111)
REC (record) SEARCH – button (p. 35) /
Record review button (p. 35) /
(rewind) button (p. 37) /
CARD – button* (p. 111)
FOCUS button (p. 75) /
(play/pause) button (p. 37)
LCD panel OPEN button (p. 32)
BATT. (battery release)
button (p. 16)
Introduction
AE SHIFT button (p. 77) /
(stop) button (p. 37) /
(index screen) button* (p. 112)
LCD screen
(p. 32)
Serial number
123456789
Battery attachment unit
(p. 16)
MENU button (p. 44)
DC IN terminal (p. 15)
Backup battery cover
(p. 19)
Selector dial (p. 40, 44)
Card access indicator* (p. 104) /
CHARGE indicator (p. 16)
Memory card slot* (p. 100)
(self-timer) button
(p. 70) /
DATA CODE button
(p. 83)
Card MIX button*
(p. 124) /
SLIDE SHOW button*
(p. 112)/
(stitch assist) button*
(p. 107)
DATA DIGITAL
CODE EFFECTS ON/OFF
DIGITAL EFFECTS
button (p. 61)
Digital effects ON/OFF button
(p. 61)
MIX/
SLIDE
SHOW
P
Program selector (p. 57)
P Program AE
Easy recording
* ZR70 MC
and ZR65 MC only.
11
E
Diopter adjustment
lever (p. 20)
Introduction
Viewfinder protect
cover (p. 142)
PHOTO button (p. 55, 104)
ZR70 MC Advanced accessory
ZR65 MC
shoe (p. 73)
ZR60 Accessory
shoe (p. 150)
Zoom lever (p. 30)
Built-in speaker
(p. 39)
Viewfinder (p. 20)
TAPE/CARD switch*
(p. 8)
TAPE
Strap mount (p. 21)
CARD
Start/stop button
(p. 28)
Grip belt (p. 20)
POWER switch (p. 8)
CAMERA
OFF
}
Strap mount (p. 21)
POWER
CAMERA
OFF
PLAY
(VCR)
PLAY(VCR)
Cassette compartment
cover (p. 22)
Cassette compartment
(p. 22)
* ZR70 MC
12
and ZR65 MC only.
E
Introduction
Terminal cover
ZR70 MC : Assist lamp
(White LED)
(p. 59)
Remote sensor (p. 24)
Stereo microphone (p. 71)
Terminal cover
S-video IN/OUT
terminal (p. 41)
S
MIC
DV IN/OUT terminal
(p. 87)
MIC terminal (p. 71)
AV
AV IN/OUT terminal
(p. 41) / (phones)
terminal (p. 39)
USB terminal *
(p. 129)
DV
Bottom view
OPEN/EJECT switch (p. 22)
Tripod socket (p. 36)
* ZR70 MC
and ZR65 MC only.
13
Wireless Controller
E
ZR70 MC ZR65 MC
q
w
e
r
t
Introduction
#1
#2
y
u
i
WL-D79
!4
START
/STOP
PHOTO
W
SELF T. D.EFFECT.
ZOOM
T
MENU
TV SCREEN ON/OFF
SET
INDEX SLIDE SHOW
CARD
ZERO SET
MEMORY REW
12bit
AUDIO OUT
PLAY
FF
STOP
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
o
!0
REC
PAUSE
WIRELESS CONTROLLER WL-D79
!1
!2
!3
!5
!6
!7
!8
!9
#3
* ZR70 MC
14
and ZR65 MC only.
w
e
r
START
/STOP
PHOTO
!5
W
ZOOM
SELF T. D.EFFECT.
T
MENU
TV SCREEN ON/OFF
t
SET
DATA CODE SEARCH SELECT
y
u
@2
@3
i
@4
o
@5
!0
!1
@6
@7
@8
@9
#0
q PHOTO button (p. 55, 104)
w D. EFFECTS (Digital effects) button (p. 61)
e START/STOP button (p. 28)
r SELF T. button (p. 70)
t TV SCREEN button (p. 134)
y DATA CODE button (p. 83)
u SEARCH SELECT button (p. 85)
i ZERO SET MEMORY button (p. 86)
o 12bit AUDIO OUT button (p. 98)
!0 AUDIO DUB. button (p. 97)
!1 REC PAUSE button (p. 89)
!2 REW button (p. 37)
!3 AV INSERT button (p. 95)
!4 Digital effects ON/OFF button (p. 61)
!5 Transmitter
!6 Zoom buttons (p. 30)
!7 Controller buttons (p. 44)
!4
q
@0
@1
DATA CODE SEARCH SELECT
WL-D80
ZR60
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
FF
2
AV INSERT AV DV REMOTE SET
REC
PAUSE
WIRELESS CONTROLLER WL-D80
!9
@0
@1
@2
@3
@4
@5
@6
@7
@9
#0
!3
MENU button (p. 44)
SET button (p. 44)
Search buttons (p. 85)
PLAY
button (p. 37)
FF
button (p. 37)
button (p. 38)
STOP
button (p. 37)
2 button (p. 38)
REMOTE SET button (p. 49)
SLOW
AV
!8
@8
!2
!8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
@9
#0
#1
#2
#3
!6
!7
button (p. 38)
DV button (p. 93)
button (p. 38)
PAUSE
button (p. 38)
INDEX button* (p. 112)
SLIDE SHOW button* (p. 112)
CARD
buttons* (p. 111)
Using a Household Power Source
You can operate the camcorder from a household power source using the supplied
power adapter. The power adapter converts current from a power outlet (100-240 V
AC, 50/60 Hz) to the DC current used by the camcorder.
E
1. Turn the POWER switch to OFF.
2. Connect the power cord to the
power adapter.
q
POWER
CAMERA
OFF
PLAY
(VCR)
3. Plug the power cord into a power
outlet.
r r
4. Connect the power adapter to the
camcorder’s DC IN terminal.
e
Mastering
the Basics
w
5. After use, disconnect the power adapter from the camcorder. Unplug
the power cord from the power outlet and disconnect it from the
adapter.
❍ Turn off the camcorder before connecting or disconnecting the power adapter.
❍ If the adapter is used close to a TV, it may cause picture interference. Move the
adapter away from the TV or the antenna cable.
❍ Do not connect any products that are not expressly recommended to the
camcorder’s DC IN terminal or to the power adapter.
❍ You may hear some noise from the power adapter during use. This is not a
malfunction.
15
Attaching and Charging the Battery Pack
E
Charge the battery pack with the supplied power adapter before you use the
camcorder for the first time and subsequently when the message “CHANGE THE
BATTERY PACK” appears.
1. Turn the POWER switch to OFF.
q
w
2. Move the viewfinder upward.
POWER
Mastering
the Basics
3. Attach the battery pack to the
camcorder.
CAMERA
OFF
PLAY
(VCR)
• Remove the terminal cover of the battery
pack.
• Align the end of the battery pack with the
line on the camcorder, press lightly and slide
it in the direction of the arrow until it clicks.
e
click
4. Connect the power cord to the
adapter.
5. Plug the power cord into a power
outlet.
6. Connect the power adapter to the
camcorder’s DC IN terminal.
7. When charging is complete,
disconnect the power adapter from
the camcorder. Unplug the power
cord from the power outlet and
disconnect it from the adapter.
DC IN terminal
DC IN 8.4V
CARD/
CHARGE
CHARGE indicator
y
r
t
8. Remove the battery pack after use.
Press the BATT. button to remove the battery.
16
❍ The battery pack may be defective when the CHARGE indicator flashes rapidly.
❍ The CHARGE indicator informs you about the charge status.
0-50%:
Flashes once every second
More than 50%: Flashes twice every second
100%:
Glows steadily
❍ Do not disconnect and reconnect the power cord while charging a battery
pack. The battery pack may not be charged correctly even if the CHARGE
indicator glows steady. The battery pack may also not be charged correctly
when a power outage occurs during charging. Remove the battery pack and
attach it back to the camcorder.
Charging, Recording and Playback Time
Below times are approximate and vary according to the charging, recording or
playback conditions.
E
Charging Time
Battery Pack
Charging Time
BP-508 (ZR65 MC/ZR60)
110 min.
BP-512 (ZR70 MC/optional)
120 min.
BP-511 (Optional)
120 min.
BP-522 (Optional)
210 min.
BP-535 (Optional)
310 min.
• Charge the battery pack in temperatures between 41º F and 104º F (5º C and 40º C).
• A lithium ion battery pack can be charged at any charge state. Unlike conventional
battery packs, you do not need to completely use or discharge it before charging.
Battery Pack
Maximum Recording Time
Typical Recording Time*
Using the Viewfinder Using the LCD Using the Viewfinder Using the LCD
BP-508
(ZR65 MC/ZR60)
100 min.
75 min.
55 min.
40 min.
BP-512
(ZR70 MC/optional)
180 min.
140 min.
95 min.
75 min.
BP-511 (Optional)
180 min.
140 min.
95 min.
75 min.
BP-522 (Optional)
370 min.
295 min.
195 min.
155 min.
BP-535 (Optional)
590 min.
470 min.
315 min.
250 min.
Mastering
the Basics
Recording Time
* Approximate times for recording with repeated operations such as start/stop, zooming,
power on/off. Actual time may be shorter.
• We recommend that you prepare battery packs 2 to 3 times longer than you think you
might need.
• To conserve battery charge, turn off the camcorder instead of leaving it in record pause
mode.
Playback Time
Battery Pack
Playback Time
Using the LCD
BP-508 (ZR65 MC/ZR60)
70 min.
BP-512 (ZR70 MC/optional)
125 min.
BP-511 (Optional)
125 min.
BP-522 (Optional)
250 min.
BP-535 (Optional)
400 min.
17
How much power is left?
The battery symbols indicate the charge status of the battery
E
pack.
When the battery pack is empty, “CHANGE THE BATTERY PACK”
appears for 4 seconds and
starts flashing.
The battery charge indicators are not constant – they vary
according to the condition under which battery pack and
camcorder are used.
Mastering
the Basics
Battery Pack Handling Precautions
DANGER!
Treat the battery pack with care.
• Keep it away from fire (or it might explode.)
• Do not expose the battery pack to temperature higher than 140º F (60º C). Do
not leave it near a heater or inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop or knock it.
• Do not get it wet.
❍ Charged battery packs continue to discharge naturally. Therefore, charge them on
the day of use, or the day before, to ensure a full charge.
❍ Attach the terminal cover whenever a battery pack is not in use. Contact to metallic
objects may cause a short circuit and damage the battery pack.
❍ Dirty terminals may cause a poor contact between the battery pack and the
camcorder. Wipe the terminals with a soft cloth.
❍ Since storing a charged battery pack for a long time (about 1 year) can shorten its
lifecycle or affect performance, we recommend to discharge the battery pack fully
and to store it in a dry place at temperatures no higher than 86˚ F (30˚ C). If you do
not use the battery pack for long periods, charge and discharge it fully at least once
a year. If you have more than 1 battery pack, perform these precautions at the
same time for all battery packs.
❍ Although the battery pack’s operating temperature range is from 32˚ F to 104˚ F
(0˚ C to 40˚ C), the optimal range is from 50˚ F to 86˚ F (10˚ C to 30˚ C). At cold
temperatures, performance will temporarily decline. Warm it in your pocket before
use.
❍ Replace the battery pack if the usable time after full charge diminishes substantially
at normal temperatures.
18
Installing the Backup Battery
The backup battery allows the camcorder to retain date, time and other camcorder
settings while the power source is disconnected. Power the camcorder from a
household power source or with a battery pack when replacing the backup battery.
1. Open the backup battery cover.
2. Insert the lithium battery with the
+ side facing outward.
q
w
E
e
3. Close the cover.
Mastering
the Basics
WARNING!
• The battery used in this device may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble, heat above 212° F (100° C) or
incinerate the battery.
• Replace the battery with a CR1616 made by Panasonic, Hitachi Maxell, Sony,
Toshiba, Varta or Renata. Use of other batteries may present a risk of fire or
explosion.
❍ Do not pick up the battery using tweezers or other metal tools as this will
cause a short circuit.
❍ Wipe the battery with a clean dry cloth to ensure proper contact.
❍ Keep the battery out of reach of children. If it is swallowed, seek medical
assistance immediately. The battery case may break and the battery fluids may
damage stomach and intestines.
❍ Do not disassemble, heat or immerse the battery in water to avoid the risk of
explosion.
The backup battery has a life span of about a year. j flashes to inform you that
it needs to be replaced.
19
Preparing the Camcorder
E
Adjusting the Viewfinder (Diopter Adjustment)
1. Turn on the camcorder and keep the
LCD panel closed to adjust the
viewfinder.
2. Adjust the diopter adjustment lever.
Mastering
the Basics
Do not leave the viewfinder exposed to direct sunlight as it may melt (due to
concentration of light by the lens). Adjust the angle of the viewfinder to prevent
sunlight from entering.
Attaching the Lens Cap
1. Attach the cord to the lens cap.
2. Pass the grip belt through the loop
on the cord.
Press the buttons on the lens cap when
attaching/removing it. Hook the lens cap on
the grip belt while you are recording, and
place it over the lens when you have finished.
Fastening the Grip Belt
Hold the camcorder with your right
hand and adjust the belt with your left.
Adjust the grip belt so that you can reach the
zoom lever and photo button with your index
finger, and the start/stop button with your
thumb.
20
Attaching the Shoulder Strap
For extra security and portability, attach the shoulder strap before using the
camcorder.
Pass the ends through the strap mount
and adjust the length of the strap.
Mounting the Wide Attachment
Mastering
the Basics
ZR70 MC
The WA-30.5 Wide Attachment gives you a wide perspective for indoor shots or
panoramic views (0.6×). The wide attachment is for use at maximum wide-angle.
E
Screw the wide attachment fully into
the lens filter thread.
❍ If you zoom to telephoto, the picture will not be in focus.
❍ Do not look directly at the sun or other strong light sources through the wide
attachment. It could damage your eyesight.
❍ When recording in wide angle with the wide attachment, the outer periphery
of the image may become curved.
❍ Filters cannot be used with the wide attachment.
❍ If dust accumulates on the wide attachment or on the camcorder lens, clean
both lenses gently with a blower brush.
❍ The wide attachment may obstruct the remote sensor (the range of the
wireless controller narrows), or may cause a shadow to appear on the picture
when recording with a video light or the assist lamp (White LED).
❍ Do not touch the lens to avoid smudges and fingerprints.
❍ Do not store the wide attachment in a humid place as it may mold.
21
Loading a Cassette
E
Use only videocassettes marked with the D logo.
Loading and Unloading
1. Slide and hold the OPEN/EJECT
switch and open the cassette
compartment cover.
Tape
protection tab
The cassette compartment opens
automatically.
w
q
3. Press the P mark on the cassette
compartment until it clicks.
e
SH
PU
• Load the cassette with the window facing
the grip belt and the REC/SAVE tab facing
upward.
• Unload the cassette by pulling it straight
out.
OPEN/EJECT
Mastering
the Basics
2. Load/unload the cassette.
Wait for the cassette compartment to retract
automatically.
4. Close the cassette compartment
cover.
click
r
❍ Do not interfere with the cassette compartment while it is opening or closing
automatically or attempt to close the cover until the cassette compartment has
fully retracted.
❍ Be careful not to get your fingers caught in the cassette compartment cover.
❍ If the camcorder is connected to a power source, cassettes can be
loaded/unloaded even if the POWER switch is set to OFF.
❍ v flashes if no cassette is inserted when turning on the power (in CAMERA
and PLAY (VCR) mode).
❍ With some types of tapes, the remaining tape display may not be accurate.
22
Protecting Tapes from Accidental Erasure
To protect your recordings from accidental
erasure, slide the tab on the cassette to the
E
left. (This switch position is usually labeled
SAVE or ERASE OFF.)
If you load a protected cassette in CAMERA
REC
SAVE
REC
SAVE
mode, the message “THE TAPE IS SET FOR
ERASURE PREVENTION” appears for approx. 4
seconds and v starts flashing. If you wish to record on that cassette, slide the tab
back to the right.
Cassette Handling Precautions
Mastering
the Basics
❍ Rewind tapes after use. If the tape becomes slack and damaged, it may cause
picture and sound distortion.
❍ Return cassettes in the case and store them upright.
❍ Do not leave the cassette in the camcorder after use.
❍ Do not use cassettes with spliced tapes or nonstandard cassettes as they may
damage the camcorder.
❍ Do not insert anything into the small holes of the cassette, or cover them with
cellophane tape.
❍ Handle cassettes with care. Do not drop or subject them to severe impact as this
may damage the cassettes.
❍ Rewind tapes from time to time if they are stored for a long time.
❍ With cassettes equipped with a memory function, metal plated terminals may
become dirty with use and the cassette’s memory function may not work properly.
Clean the terminals with a cotton swab after about 10 times of loading/unloading.
23
Using the Wireless Controller
E
You can operate the camcorder with the
supplied wireless controller from a distance of
up to 16 feet (5 m). Point it at the camcorder’s
remote sensor when you press the buttons.
Mastering
the Basics
Following functions cannot be operated
without the wireless controller:
• Some special playback modes (
• Photo/date search (
85)
• Zero set memory (
86)
• Analog line-in (
89)
• DV dubbing (
90)
• AV Insert (
94)
• Audio dubbing (
96)
38)
❍ The wireless controller may not work properly in bright places, such as
outdoors under direct sunlight, or when used too close to the camcorder.
❍ The operable range of the wireless controller may shorten when the
camcorder’s remote sensor is exposed to strong light.
❍ When the batteries run out, replace both at the same time.
Inserting Batteries
The wireless controller operates with two AA batteries.
ZR70 MC ZR65 MC
q
WL-D79
ZR60
q
WL-D80
w
w
e
e
1. Open the battery cover.
2. Insert the batteries following the + and – markings.
3. Close the battery cover.
24
Setting the Time Zone, Date and Time
Set the time zone, date and time when you first start using your camcorder. Install the
backup battery before you begin (
19).
E
Setting the Time Zone/Daylight Saving Time
CAMERA
(
44)
SYSTEM
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
T.ZONE/DST•••N.Y.
1. Press the MENU button to open the menu.
MENU
Mastering
the Basics
2. Turn the selector dial to select [SYSTEM] and press
the selector dial.
3. Turn the selector dial to select [T.ZONE/DST] and
press the selector dial.
• The time zone setting appears.
• The default setting is New York. Select your time zone and daylight saving time (DST)
setting if necessary.
4. Turn the selector dial to select the setting option that represents your
time zone.
To adjust for daylight saving time, select the time zone with the U next to the area.
5. Press the MENU button to close the menu.
MENU
25
16
1
E
19
18
24
20
4
2
3
17
6
7
10
9
15
8
5
21
23
14
12
22
11
13
14 15 16 17 18 19 20 21 22 23 24
No. Time zone
2
3
4
5
6
7
8
9
10 11 12 13
No. Time zone
LONDON
PARIS
CAIRO
MOSCOW
DUBAI
KARACHI
DACCA
BANGKOK
H. KONG (Hong Kong)
TOKYO
SYDNEY
SOLOMON
Mastering
the Basics
1
WELLGTN (Wellington)
SAMOA
HONOLU. (Honolulu)
ANCHOR. (Anchorage)
L.A. (Los Angeles)
DENVER
CHICAGO
N.Y. (New York)
CARACAS
RIO (Rio de Janeiro)
FERNAN. (Fernando de Noronha)
AZORES
❍ Once you have set time zone, date and time, you do not need to reset the
clock each time you travel to another time zone. Just set the time zone to the
one of your destination, and the camcorder automatically adjusts the clock.
❍ Days per month and leap years will be automatically adjusted.
Setting the Date and Time
CAMERA
(
44)
SYSTEM
PLAY (VCR)
CARD CAMERA
D/TIME SET•••JAN. 1,2003
12:00 PM
1. Press the MENU button to open the menu.
26
CARD PLAY (VCR)
MENU
2. Turn the selector dial to select [SYSTEM] and press
the selector dial.
3. Turn the selector dial to select [D/TIME SET] and
press the selector dial.
E
The year display starts to flash.
4. Turn the selector dial to select the year, and press the selector dial.
• The next part of the display starts flashing.
• Set the month, day, hours and minutes in the same way.
5. Press the MENU button to close the menu and to
start the clock.
MENU
Time zone, date and time appear for 4 seconds each time you
turn the power on.
Displaying Date and Time during Recording
Mastering
the Basics
❍ To change a part of the date or time, press the selector dial at step 4, and
move to the part you wish to change.
❍ The date can be set to any year between 2003 and 2030.
You can display time zone, date and time in the lower left corner of the screen (the
time zone disappears after 4 seconds). The 4-second display will no longer appear
when you turn the power on. The date and time display will not be superimposed on
your recordings.
CAMERA
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
CARD PLAY (VCR)
D/T DISPLAY••OFF
1. Press the MENU button to open the menu.
MENU
2. Turn the selector dial to select [DISPLAY SET UP] and
press the selector dial.
3. Turn the selector dial to select [D/T DISPLAY] and
press the selector dial.
4. Turn the selector dial to select [ON].
5. Press the MENU button to close the menu.
MENU
27
Recording Movies on a Tape
E
You can use the LCD screen or the viewfinder when recording.
Before You Begin Recording
Make a test recording first to check if the camcorder operates correctly. Before you
make important recordings, clean the video heads (
142).
Preparations
Connect a power source. Load a cassette.
Recording
1. Remove the lens cap.
ZR70 MC/ZR65 MC
Mastering
the Basics
2. Set the camcorder to CAMERA mode.
If you have not set the time zone, date and
time, “SET THE TIME ZONE, DATE AND TIME”
appears. See Setting the Time Zone, Date and
Time (
25).
q
TAPE
CARD
w
CAMERA
OFF
PLAY
(VCR)
3. Open the LCD panel (
32).
rt
To use the viewfinder, keep the LCD panel
closed or rotate it so that the screen faces in
the same direction of the lens (
33).
CAMERA
OFF
PLAY
(VCR)
4. Press the start/stop button to begin
recording.
Wait until the tape counter came to a
complete stop before you begin recording.
5. Press the start/stop button again to
pause recording.
Restart recording by pressing the start/stop button.
28
e
When You Have Finished Recording
1. Turn the POWER switch to OFF.
2. Close the LCD panel.
3. Replace the lens cap.
E
4. Unload the cassette.
5. Disconnect the power source.
When recording outdoors or through a window, do not leave LCD screen,
viewfinder or lens exposed to direct sunlight as it may cause damage.
Mastering
the Basics
❍ Turn the power off if you do not intend to use the camcorder for a longer
time.
❍ The camcorder will shut off after 5 minutes when left in record pause mode to
protect tape and video heads. To continue recording, turn the POWER switch
to OFF and then back to CAMERA.
❍ For when to use the [ (Easy Recording) or Q (program AE) mode, see Using
the Recording Programs (
57).
❍ When you do not remove the cassette, you can record the next scene without
producing any noise or blank sections between the recordings even if you turn
the camcorder off.
❍ About the built-in microphone: When recording near loud sounds (such as
fireworks, drums or concerts), sound may become distorted or may be
recorded not in the actual sound level.
❍ For extra recording time, see Changing the Recording Mode (
54).
29
Zooming
E
The camcorder’s zoom lens allows you to choose the best picture angle for your
recordings. The camcorder automatically switches between optical zooming and
digital zooming. Image resolution is slightly lower with the digital zoom.
T
Zoom in
W
Zoom out
Optical Zoom
Mastering
the Basics
ZR70 MC
22× optical zoom
ZR65 MC
20× optical zoom
ZR60
18× optical zoom
Move the zoom lever toward W to zoom out (wideangle). Move it toward T to zoom in (telephoto).
• Press the zoom lever slightly for a slow zoom. Press harder for a
faster zoom.
• You can also use the T and W buttons on the wireless controller.
However, you cannot control the zoom speed.
Digital Zoom
ZR70 MC
88×/440× digital zoom
CAMERA
(
44)
ZR65 MC
80×/400× digital zoom
PLAY (VCR)
CAMERA SET UP
ZR60
72×/360× digital zoom
CARD CAMERA
D.ZOOM••••••••88×
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [CAMERA SET UP] and
press the selector dial.
3. Select [D.ZOOM] and press the selector dial.
4. Select a setting option.
30
CARD PLAY (VCR)
MENU
5. Press the MENU button to close the menu.
MENU
E
❍ Keep at least 3.28 ft. (1m) to the subject. At wide-angle, you can focus on a
subject as close as 0.39 in. (1cm).
❍ A zoom indicator appears for 4 seconds. It extends in light blue when the
digital zoom is set to 88×/80×/72×, and extends further in dark blue when set
to 440×/400×/360×.
❍ Digital zoom cannot be used in the Night mode and Super Night (ZR70 MC)
mode.
❍ Digital zoom cannot be used when the multi-image screen is selected.
❍ ZR70 MC ZR65 MC Because the image stabilizer cannot be used in CARD
CAMERA mode, we recommend mounting the camcorder on a tripod at large
magnifications.
Mastering
the Basics
31
Using the LCD Screen
E
1. Push the OPEN button at the LCD
panel and open the LCD panel.
The LCD screen switches on and the
viewfinder switches off.
2. Rotate the LCD panel and choose the
angle of the screen.
You can rotate the LCD panel so that the
screen faces in the same direction as the lens
(
33), or push it flat against the camcorder with the screen facing outward.
Mastering
the Basics
3. Close the LCD panel after use.
• Close the LCD panel firmly until it clicks.
• The LCD screen switches off and the
viewfinder switches on.
❍ Make sure to open the LCD panel at 90 degrees before rotating it.
❍ Rotate the LCD panel in the vertical position before closing the LCD panel.
❍ When recording outdoors or through a window, do not leave the LCD screen,
viewfinder or lens exposed to direct sunlight as it may cause damage.
❍ Do not hold the camcorder by the LCD panel or the viewfinder.
❍ About the LCD Screen: The LCD screen is produced with extremely highprecision manufacturing techniques, with more than 99.99% of the pixels
operating to specification. Less than 0.01% of the pixels may occasionally
misfire or appear as black or green dots. This has no effect on the recorded
image and does not constitute a malfunction.
❍ Bright light or reflected light may cause a vertical light bar to appear on the
screen. This is not a malfunction.
❍ Bright light may make it difficult to use the LCD screen. In such case, use the
viewfinder instead.
32
Adjusting the Brightness of the LCD Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
(
44)
DISPLAY SET UP
BRIGHTNESS•• –
+
1. Press the MENU button to open the menu.
MENU
2. Turn the selector dial to select [DISPLAY SET UP] and
press the selector dial.
3. Turn the selector dial to select [BRIGHTNESS] and
press the selector dial.
Turn the selector dial up to make the screen brighter and down to make it darker.
5. Press the MENU button to close the menu.
MENU
Mastering
the Basics
4. Turn the selector dial and adjust the level.
Changing the brightness of the LCD screen does not affect that of the viewfinder
or the recordings.
Allowing the Subject to Monitor the LCD Screen
You can rotate the LCD panel so that the
screen faces in the same direction as the lens.
The viewfinder switches on allowing you to
use the viewfinder while the subject can
monitor the screen.
When you rotate the screen so that the screen faces in the same direction as the lens,
the image appears mirror reversed (LCD MIRROR ON). However, you can choose to
display the image as it is being recorded (LCD MIRROR OFF).
33
CAMERA
E
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
CARD PLAY (VCR)
LCD MIRROR••ON
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] and press the selector
dial.
3. Turn the selector dial to select [LCD MIRROR] and press the selector dial.
4. Turn the selector dial to select [OFF].
5. Press the MENU button to close the menu.
Mastering
the Basics
When [LCD MIRROR] is set to [ON], most screen displays appear mirror reversed.
34
Searching and Reviewing when Recording
REC (record) SEARCH – button/
v Record review button
REC SEARCH + button
E
Record Review
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
Mastering
the Basics
In record pause mode, this function allows you to review the last few seconds of your
recording to check if it has been recorded properly.
Press and release the c (record review) button.
The camcorder rewinds the tape, plays back the last few seconds,
and returns to record pause mode.
Record Search
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
In record pause mode, this function allows you to play back the tape (forward or
reverse) to locate the point where you wish to begin recording.
Press and hold the REC SEARCH + button (forward) or –
button (reverse).
• Release the button at the point you wish to begin recording.
• The camcorder returns to record pause mode.
❍ Noise may appear on the screen when you play back the tape in reverse.
❍ There will be no sound during Record Review and Record Search.
35
Tips for Making Better Videos
Holding the Camcorder
E
For maximum stability, grip the camcorder in your right hand and keep your right
elbow pressed against your body. If necessary, support the camcorder with your left
hand. Be careful that your fingers do not touch the microphone or lens.
High-angle Recording
Low-angle Recording
Mastering
the Basics
For More Stability
Lean against a wall
Put the camcorder on a table
Lie on your elbow
Use a tripod
Lighting
When recording outdoors, we recommend
recording with the sun at your back.
36
❍ When using a tripod, do not leave the viewfinder exposed to direct sunlight as
it may melt (due to concentration of the light by the lens).
❍ Do not use tripods with fastening screws longer than 0.2 inch (5.5 mm) as it
may damage the camcorder.
Playing Back a Tape
When you use the LCD screen for playback, the camcorder plays back the sound via
built-in speaker. The built-in speaker is monaural. Use headphones for stereo sound or
when using the viewfinder for playback.
E
Preparations
Connect a power source. Load a cassette.
Playback
1. Set the camcorder to PLAY (VCR)
mode.
ZR70 MC/
ZR65 MC
TAPE
CARD
CAMERA
OFF
PLAY
(VCR)
2. Open the LCD panel.
You can also close the LCD panel with the
screen facing outward.
r
e
Mastering
the Basics
q
t
3. Press the ` button to rewind the
tape.
To fast forward the tape, press the 1
button. To stop playback, press the 3 button.
4. Press the e/a button to begin
playback.
w
5. Press the 3 button to stop playback.
❍ If the playback picture is distorted, clean the video heads using a Canon Head
Cleaning Cassette or a commercially available digital video head-cleaning
cassette.
❍ To use the viewfinder, close the LCD panel. The built-in speaker does not
sound. Use headphones when using the viewfinder (
39).
❍ For displaying the date and time during playback, see Displaying the Data Code
(
83).
37
Special Playback Modes
Special playback modes (except of playback pause and fast/rewind playback) can only
E
be operated with the wireless controller.
` (rewind) button
1 (fast forward) button
REW
PLAY
FF
STOP
PAUSE
SLOW
2
3 (stop) button
e/a (play/pause) button
e/a (Playback Pause)
Mastering
the Basics
To pause playback, press the e/a button. Press the e/a button to resume playback.
The camcorder goes into stop mode after 5 minutes in playback pause mode.
1 (Fast Forward Playback) / ` (Rewind Playback)
Plays back the tape at 9.5 times normal speed (forward or reverse). Press and hold the
button during normal playback or fast forward.
+/ae (Frame Advance) / –/4a (Frame Reverse)
Plays back frame-by-frame. Press the button repeatedly during playback pause. Press
and hold it to play back continuous frame advance/frame reverse.
SLOW I (Slow Forward)/(Slow Reverse)
Plays back at about 1/3 normal speed. For slow forward playback, press the SLOW M
button. For slow reverse playback, press the –/4a button followed by the SLOW M
button. Press the e (play) button to return to normal playback.
–/4a (Reverse Playback)
Plays back in reverse at normal speed. Press the button during normal playback. Press
the e (play) button return to normal playback. The camcorder goes into stop mode
after 5 minutes in reverse playback pause.
× 2 (Forward× 2 Playback)/(Reverse 2× Playback)
Plays back at 2 times normal speed. Press the button during normal or reverse
playback. Press the e (play) button return to normal playback.
❍ There is no sound during special playback.
❍ The picture may become distorted during some special playback modes.
38
Playing Back with the Built-in Speaker/Headphones
Built-in speaker
H (phones) terminal
E
AV
Selector dial
MENU button
When using the built-in speaker, make sure that “H” is not displayed on the
screen. When using the headphones, make sure that “H” is displayed. Change
the setting as necessary following the procedure below.
Switching the AV/Headphones Terminal
(
44)
VCR SET UP
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
AV/PHONES•••AV
1. Press the MENU button to open the menu.
Mastering
the Basics
CAMERA
MENU
2. Turn the selector dial to select [VCR SET UP] and
press the selector dial.
3. Turn the selector dial to select [AV/PHONES] and
press the selector dial.
4. Turn the selector dial to select [AV] or [PHONES H].
5. Press the MENU button to close the menu.
MENU
❍ The built-in speaker does not sound when “H” is displayed.
❍ Do not connect headphones unless “H” is displayed as it produces noise.
❍ The built-in speaker is monaural. Use headphones for stereo sound.
❍ The built-in speaker turns off when the camcorder is set to a mode other than
the PLAY (VCR) mode or when you use the headphones.
39
Adjusting the Volume
CAMERA*
E
PLAY (VCR)
CARD CAMERA*
CARD PLAY (VCR)
*Headphone volume only.
Turn the selector dial up to increase the volume, and
down to lower the volume.
• A volume bar appears for 4 seconds.
• You can turn off the volume completely by turning the selector
dial down until OFF appears. Turn the selector dial up to increase the volume again.
Mastering
the Basics
❍ Sound may become distorted when the volume is turned up too high.
❍ The headphone volume can be adjusted in all operating modes.
❍ The camcorder retains the setting even if you turn it off (separately for
headphones and built-in speaker).
40
Playing Back on a TV Screen
You can connect the camcorder to a TV or VCR to play back your recordings on a TV
screen.
E
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting (
39).
❍ When you use the TV as a monitor during recording, keep the TV volume
turned down as long as the camcorder’s audio terminals are connected. An
unpleasant high-pitched squeal, called feedback, may be produced if sound
from the TV speakers is picked up by the microphone.
❍ For high picture quality, we recommend using a TV with an S (S1) terminal.
❍ TVs with S1-terminal or Video ID-1 system: Recordings made in the 16:9 mode
(
52) will be automatically played back in wide screen mode.
TVs with S (S1)-Video Input Terminal
Mastering
the Basics
Refer also to the TV or VCR instruction manual.
S
DV
INPUT
Signal flow
S-150 S-video Cable (optional)
S(S1)-VIDEO
VIDEO
AUDIO
L
AV
Signal flow
STV-250N Stereo Video Cable (supplied)
R
1. Turn off all devices before starting the connections.
2. Connect the S-150 S-video Cable (optional) to the S-video terminals.
41
3. Connect the STV-250N Stereo Video Cable to the camcorder’s AV
terminal and the audio terminals of the TV/VCR.
E
Connect the white plug to the white AUDIO terminal L (left), and the red plug to the
red AUDIO terminal R (right). Do not connect the yellow plug.
4. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
TVs with Audio/Video Terminals
Refer also to the TV or VCR instruction manual.
Mastering
the Basics
VIDEO
AUDIO
L
AV
Signal flow
R
STV-250N Stereo Video Cable (supplied)
1. Turn off all devices before starting the connections.
2. Connect the STV-250N Stereo Video Cable to the camcorder’s AV
terminal and the audio/video terminals on the TV/VCR.
Connect the white plug to the white audio terminal L (left), the red plug to the red
audio terminal R (right) and the yellow plug to the yellow video terminal VIDEO.
3. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
42
Selecting the Audio Output Channel
You can select the output channels when playing back a tape with audio recorded on
two channels.
CAMERA
(
44)
E
PLAY (VCR)
AUDIO SET UP
CARD CAMERA
CARD PLAY (VCR)
OUTPUT CH•••L/R
1. Press the MENU button to open the menu.
MENU
2. Turn the selector dial to select [AUDIO SET UP] and
press the selector dial.
Mastering
the Basics
3. Turn the selector dial to select [OUTPUT CH] and
press the selector dial.
4. Turn the selector dial to select a setting option.
• L/R: Stereo: L+R channels, Bilingual: Main+Sub.
• L/L: Stereo: L channel, Bilingual: Main.
• R/R:Stereo: R channel, Bilingual: Sub.
5. Press the MENU button to close the menu.
MENU
The setting resets to the L/R setting when you turn the camcorder off.
43
Menus and Settings
E
Many of the camcorder’s advanced functions are selected from menus that appear on
the screen.
Selecting Menus and Settings
1. Set the camcorder to the correct operating mode.
CAMERA
OFF
PLAY
(VCR)
ZR70 MC/ZR65 MC:
TAPE
CARD
Using the Full Range
of Features
2. Press the MENU button to open the menu.
MENU
3. Turn the selector dial to select a submenu and press
the selector dial.
4. Turn the selector dial to select a menu item and
press the selector dial.
5. Turn the selector dial to select a setting option.
6. Press the MENU button to close the menu.
When setting the white balance or shutter speed, press the
selector dial first before pressing the MENU button.
MENU
❍ Pressing the MENU button at any time closes the menu.
❍ Selecting [[ RETURN] takes you back one level.
❍ Items that are not available appear in purple.
❍ You may find it more convenient to use the wireless controller to operate the
menu. Press the MENU button on the wireless controller to open or close the
menu. Use the arrow keys in place of the selector dial and press the SET button
in place of pressing the selector dial.
44
Menu and Default Settings
Default settings are shown in boldface.
CAMERA Menu (CAM. MENU)
PLAY (VCR)
CAMERA
Submenu
\ CARD MIX *2
Menu Item
MIX TYPE
ANIMAT. TYPE
CARD CAMERA
Setting Options
CARD CHROMA, CARD LUMI.,
CAM. CHROMA, C. ANIMATION
CORNER, STRAIGHT, RANDOM
MIX LEVEL
IMAGE S. i
16:9
WHITE BAL.
ON, OFF
AUTO, SET W, INDOOR T, OUTDOOR U
52
80
REC MODE
SP, LP
54
AV/PHONES
AV, PHONES H
39
WIND SCREEN
ON, OFF
71
AUDIO MODE
16bit, 12bit
71
LCD MIRROR
ON, OFF
34
TV SCREEN
ON, OFF
134
D/T DISPLAY
ON, OFF
27
DEMO MODE
ON, OFF
53
SYSTEM
ON, PUSH ON, OFF
51
WL. REMOTE
GREEN, ORANGE, BLUE, YELLOW,
TURQUOISE, PURPLE
A1, A2, OFF B
49
BEEP
ON, OFF
52
T.ZONE/DST
See list of time zones
BRIGHTNESS
33
BUTTONLIGHT *1
LIGHT COLOR
*1
D/TIME SET
MY CAMERA
51
25
26
S-UP IMAGE *3
SHTR SOUND
Using the Full Range
of Features
DISPLAY SET UP
123
AUTO, 1/60, 1/100, 1/250, 1/500, 1/1000,
78
1/2000
ZR70 MC
ZR65 MC
ZR60
30
OFF, 88×, 440× OFF, 80×, 400× OFF, 72×, 360×
ON, OFF
69
D. ZOOM
AUDIO SET UP
122
122
CAMERA SET UP SHUTTER
VCR SET UP
E
CARD CAMERA
*2
S-UP SOUND
ON, OFF
50
PATTERN1, PATTERN2, PATTERN3
50
PATTERN1, PATTERN2, PATTERN3
50
S/STOP SOUND
PATTERN1, PATTERN2, PATTERN3
50
SELF-T SOUND
PATTERN1, PATTERN2, PATTERN3
50
*1 ZR70 MC , *2 ZR70 MC and ZR65 MC , *3
ZR60
45
PLAY (VCR) Menu (VCR MENU)
CAMERA
E
Submenu
VCR SET UP
AUDIO SET UP
CARD CAMERA
PLAY (VCR)
CARD CAMERA
Menu Item
REC MODE
SP, LP
Setting Options
54
AV/PHONES
AV, PHONES H
39
AV \ DV OUT
ON, OFF
93
OUTPUT CH
L/R, L/L, R/R
43
AUDIO DUB.
AUDIO IN, MIC. IN
97
WIND SCREEN
ON, OFF
71
AUDIO MODE
16bit, 12bit
71
12bit AUDIO
STEREO1, STEREO2, MIX/FIXED, MIX/VARI.
98
SI QUALITY
SUPER FINE, FINE, NORMAL
101
MOVIE SIZE *1
320 × 240, 160 × 120
102
FILE NOS.
RESET, CONTINUOUS
103
COPY
CANCEL, EXECUTE
126
MIX BALANCE
Using the Full Range
of Features
CARD SET UP *2
CARD
OPERATIONS *2
DISPLAY SET UP
SYSTEM
\
98
BRIGHTNESS
33
DISPLAYS
ON, OFF <PLAYBK>
134
6SEC. DATE
ON, OFF
84
DATA CODE
DATE/TIME, CAMERA DATA, CAM. & D/T
84
D/TIME SEL.
DATE, TIME, DATE & TIME
84
BUTTONLIGHT *1
ON, PUSH ON, OFF
51
LIGHT COLOR *1
51
WL. REMOTE
GREEN, ORANGE, BLUE, YELLOW,
TURQUOISE, PURPLE
A1, A2, OFF B
49
BEEP
ON, OFF
52
T.ZONE/DST
See list of time zones
25
S-UP IMAGE*3
ON, OFF
50
SHTR SOUND *2
PATTERN1, PATTERN2, PATTERN3
50
D/TIME SET
MY CAMERA
46
26
S-UP SOUND
PATTERN1, PATTERN2, PATTERN3
50
S/STOP SOUND
PATTERN1, PATTERN2, PATTERN3
50
SELF-T SOUND
PATTERN1, PATTERN2, PATTERN3
50
*1 ZR70 MC , *2 ZR70 MC and ZR65 MC , *3
ZR60
ZR70 MC ZR65 MC
CARD CAMERA Menu (C. CAM. MENU)
CAMERA
PLAY (VCR)
Submenu
Menu Item
CAMERA SET UP SHUTTER
CARD SET UP
VCR SET UP
AUDIO SET UP
*1
DISPLAY SET UP
CARD PLAY (VCR)
Setting Options
AUTO, 1/60, 1/100, 1/250
AUTO, SET W, INDOOR T, OUTDOOR U
80
SI QUALITY
SUPER FINE, FINE, NORMAL
101
SI SIZE
1024 × 768, 640 × 480
101
MOVIE SIZE *1
320 × 240, 160 × 120
102
FILE NOS.
RESET, CONTINUOUS
103
AV/PHONES
AV, PHONES H
39
WIND SCREEN
ON, OFF
71
BRIGHTNESS
33
ON, OFF
34
TV SCREEN
ON, OFF
134
D/T DISPLAY
ON, OFF
27
ON, OFF
53
ON, PUSH ON, OFF
51
51
WL. REMOTE
GREEN, ORANGE, BLUE, YELLOW,
TURQUOISE, PURPLE
A1, A2, OFF B
49
BEEP
ON, OFF
52
T.ZONE/DST
See list of time zones
25
BUTTONLIGHT
*1
D/TIME SET
Using the Full Range
of Features
LCD MIRROR
LIGHT COLOR *1
MY CAMERA
E
78
WHITE BAL.
DEMO MODE
SYSTEM
CARD CAMERA
26
SHTR SOUND
PATTERN1, PATTERN2, PATTERN3
50
S-UP SOUND
PATTERN1, PATTERN2, PATTERN3
50
S/STOP SOUND
PATTERN1, PATTERN2, PATTERN3
50
SELF-T. SOUND
PATTERN1, PATTERN2, PATTERN3
50
*1 ZR70 MC
47
ZR70 MC ZR65 MC
CARD PLAY (VCR) Menu (C.PLAY MENU)
CAMERA
E
Submenu
CARD
OPERATIONS
(Single Image
Display)
CARD PLAY (VCR)
Menu Item
COPY \
Setting Options
CANCEL, EXECUTE
127
PRINT ORDERS
ALL ERASE
YES, NO
117
IMAGE ERASE
CANCEL, SINGLE, ALL
115
FORMAT
CANCEL, EXECUTE
128
CARD
OPERATIONS
(Index Screen)
\
VCR SET UP
REC MODE
SP, LP
54
AV/PHONES
AV, PHONES H
39
DISPLAY SET UP
\
PROTECT
Using the Full Range
of Features
SYSTEM
MY CAMERA
\
PRINT
*1 ZR70 MC
114
PRINT ORDER
116
BRIGHTNESS
DISPLAYS
48
CARD CAMERA
PLAY (VCR)
33
ON, OFF
134
D/TIME SEL.
DATE, TIME, DATE & TIME
84
BUTTONLIGHT *1
ON, PUSH ON, OFF
51
LIGHT COLOR *1
51
WL. REMOTE
GREEN, ORANGE, BLUE, YELLOW,
TURQUOISE, PURPLE
A1, A2, OFF A
BEEP
ON, OFF
52
T.ZONE/DST
See list of time zones
25
49
D/TIME SET
26
CREATE START-UP IMAGE
130
SEL. S-UP IMG
NO IMAGE, CANON LOGO, MY IMAGE
50
SHTR SOUND
PATTERN1, PATTERN2, PATTERN3
50
S-UP SOUND
PATTERN1, PATTERN2, PATTERN3
50
S/STOP SOUND
PATTERN1, PATTERN2, PATTERN3
50
SELF-T SOUND
PATTERN1, PATTERN2, PATTERN3
Appears when connecting a printer with direct print function.
50
118
Changing the Remote Sensor Mode
Two remote sensor modes and an off setting are available to prevent interference
from other Canon wireless controllers being used nearby.
E
Turning the Remote Sensor Off
CAMERA
(
44)
PLAY (VCR)
SYSTEM
CARD CAMERA
WL.REMOTE•••
CARD PLAY (VCR)
1
Open the menu and select [SYSTEM]. Select [WL.
REMOTE], set it to [OFF B] and close the menu.
[B] appears.
Changing the Remote Sensor Mode
CAMERA
44)
SYSTEM
CARD CAMERA
WL.REMOTE•••
CARD PLAY (VCR)
1
Using the Full Range
of Features
(
PLAY (VCR)
1. On the camcorder, open the menu and select
[SYSTEM]. Select [WL. REMOTE], set it to [A 2] and
close the menu.
The selected mode appears for 4 seconds.
2. On the wireless controller, press and hold the
REMOTE SET button. Set the mode to the same of
the camcorder. Press the ZOOM T button for mode 2.
Keep the button pressed for over 2 seconds.
If you have set the camcorder to mode 1, press the ZOOM W
button for mode 1.
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
REC
PAUSE
WIRELESS CONTROLLER WL-D79
START
/STOP
PHOTO
SELF T. D.EFFECT.
TV SCREEN ON/OFF
W
ZOOM
T
MENU
SET
❍ The wireless controller returns to mode 1 when you replace the batteries.
Change the mode if necessary.
❍ Make sure that camcorder and wireless controller are set to the same mode.
Display the camcorder’s mode by pressing any button on the wireless controller
(except of the REMOTE SET button) and set the wireless controller’s mode to
the same mode. Change the batteries if the wireless controller still does not
work.
49
Customizing the Camcorder
E
You can personalize your camcorder by customizing the start-up image and the sound
it makes for start-up, shutter*, start/stop and self-timer (collectively called the My
Camera settings).
* ZR70 MC and ZR65 MC only. With the ZR70 MC and ZR65 MC, you can also create
your own start-up image. See Creating a Start-up Image (
130).
Changing the My Camera Settings
CAMERA
(
44)
MY CAMERA
PLAY (VCR)
CARD CAMERA
S–UP IMAGE•••ON
CARD PLAY (VCR)
(ZR60)
SHTR SOUND•••PATTERN1
S–UP SOUND•••PATTERN1
Using the Full Range
of Features
S/STOP SOUND•PATTERN1
SELF–T SOUND•PATTERN1
1. Open the menu and select [MY CAMERA].
2. Select the menu item you wish to change.
•
ZR70 MC ZR65 MC When selecting a start-up image (only in CARD PLAY (VCR) mode):
[NO IMAGE], [CANON LOGO] and [MY IMAGE] appears.
• ZR60 When selecting a start-up image: [OFF] and [ON] appears.
• When selecting a sound: [PATTERN1], [PATTERN2] and [PATTERN3] appear.
3. Select a setting option and close the menu.
50
ZR70 MC
Setting the Light-up Buttons
The buttons above the LCD panel light up
E
when the camcorder’s power is on, or when
you press a button. This is helpful if, for
example, you wish to play back a tape in dark
places.
You can select the color of the light-up
buttons from green, orange, blue, yellow,
turquoise and purple.
MENU button
Selector dial
Selecting the Light-up Setting
CAMERA
(
44)
PLAY (VCR)
SYSTEM
CARD CAMERA
CARD PLAY (VCR)
BUTTONLIGHT•ON
• ON: The buttons light up while the camcorder is turned on. The color changes when you
press a button and turns back when you release the button.
• PUSH ON: The buttons light up when you press a button and turn off when you release
the button.
• OFF: Buttons do not light up.
Using the Full Range
of Features
Open the menu and select [SYSTEM]. Select [BUTTONLIGHT], set it to
[PUSH ON] or [OFF] and close the menu.
Selecting the Color of the Buttons
CAMERA
(
44)
SYSTEM
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
LIGHT COLOR•TURQUOISE
Open the menu and select [SYSTEM]. Select [LIGHT COLOR], set it to the
desired color and close the menu.
You cannot change the color of the buttons when [BUTTONLIGHT] is set to [OFF].
51
Other Camcorder Settings
E
Beep
You will hear a beep upon camcorder operations such as power on/off, start/stop, selftimer countdown, automatic shut-off, and unusual conditions of the camcorder. The
beep will not be recorded.
If you turn off the beep, all camcorder sounds including the ones of the My Camera
settings will be turned off.
CAMERA
(
44)
PLAY (VCR)
SYSTEM
CARD CAMERA
CARD PLAY (VCR)
BEEP•••••••••ON
To turn the beep off, open the menu and select [SYSTEM]. Select [BEEP],
set it to [OFF] and close the menu.
Recording in 16:9 (Wide Screen TV Recording)
Using the Full Range
of Features
You can record in the 16:9 format for playback on wide screen TVs.
CAMERA
(
44)
PLAY (VCR)
CAMERA SET UP
CARD CAMERA
CARD PLAY (VCR)
16:9••••••••OFF
To switch 16:9 on, open the menu and select [CAMERA SET UP]. Select
[16:9], set it to [ON] and close the menu.
”16:9” appears.
❍ The 16:9 mode cannot be selected in the Easy Recording mode.
❍ The multi-image screen cannot be used when the 16:9 format is selected.
❍ If you play back a 16:9 recording on a normal TV, the image appears vertically
“squashed” (compressed).
❍ If you connect the camcorder to a TV with an S1 terminal or Video ID-1
system, recordings made in the 16:9 mode will be automatically played back in
wide screen mode.
52
Demonstration Mode
The demonstration mode displays the camcorder’s main features. It starts
automatically when you leave the camcorder turned on without loading a cassette
(ZR70 MC/ZR65 MC: and without inserting a memory card) for more than 5 minutes.
You can also start the demonstration mode through the menu.
CAMERA
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
E
CARD PLAY (VCR)
DEMO MODE•••ON
With no cassette (ZR70 MC/ZR65 MC: and memory card) inserted, open the
menu and select [DISPLAY SET UP]. Select [DEMO MODE], set it to [OFF]
and close the menu.
To cancel the demo mode, press any button, turn off the camcorder, load a cassette
(ZR70 MC/ZR65 MC: or insert a memory card).
Using the Full Range
of Features
53
Changing the Recording Mode (SP/LP)
E
You can choose from SP (standard play) and LP (long play). LP extends the tape usage
by 1.5 times.
❍ Tapes recorded in LP mode cannot be used for audio dubbing (
96) or AV
insert (
94).
❍ Depending on the nature and usage condition of the tape, picture and sound
recorded in LP mode may be distorted. We recommend using the SP mode for
important recordings.
❍ We recommend recording in SP mode if you plan to transfer the images to a
computer.
❍ If you record in both SP and LP modes on the same tape, the playback picture
may become distorted and the time code may not be written correctly.
❍ If you play back a tape that has been recorded in LP mode with another digital
device on this camcorder, or vice versa, picture and sound may become
distorted.
Using the Full Range
of Features
CAMERA
54
(
44)
VCR SET UP
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
REC MODE••••SP
To change to LP mode, open the menu and select [VCR SET UP]. Select
[REC MODE], set it to [LP] and close the menu.
Recording Still Images on the Tape
You can record still images on the tape. Starting your recording with a still image
allows you to easily locate the beginning of the recording with the Photo Search
function (
85).
E
PHOTO button
PHOTO button
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
In Record Pause Mode
1. Press the PHOTO button halfway.
Using the Full Range
of Features
O
OT
PH
• Autofocus: F flashes in white and turns green when focus is
adjusted.
• Manual focus: F flashes in green. Adjust the focus with the
selector dial.
• Exposure is locked.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
2. Press the PHOTO button fully.
OT
PH
O
• F disappears.
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound.
• The camcorder returns to record pause mode.
During Recording
1. Press the PHOTO button fully.
O
PH
TO
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound
• The camcorder returns to record pause mode.
55
Using the Full Range
of Features
E
56
❍ When you turn the POWER switch to OFF while the camcorder is recording the
still image, it will not turn off until recording is complete.
❍ Record still images under sufficient lighting condition (in which you can identify
the subject on the screen).
❍ If a subject is unsuitable for autofocus, F continues to flash. Keep the PHOTO
button pressed halfway and adjust the focus with the selector dial.
Using the Recording Programs
The camcorder is equipped with the Easy Recording program and several program AE
modes. The availability of functions differs depending on the selected mode.
E
Availability of Functions in Each Mode:
Position of the
Program Selector
[
Recording Program
[
Digital Zoom
h
White Balance
*1
h
A
h
A
h
h
AE Shift
Image Stabilizer*2
Digital Effects
*1
×
h
Shutter Speed
Focus
Q
ON
h
×
16:9
×
Card Mix*3
×
×
h*4
h
h
×
Using the Full Range
of Features
A: Auto setting h: Available ×: Not available
*1 ZR70 MC only.
*2 The image stabilizer cannot be used in CARD CAMERA mode.
*3 ZR70 MC and ZR65 MC only.
*4 Available effects depend upon the program AE mode.
Easy Recording Program
The camcorder adjusts focus, exposure and other settings
automatically, allowing you to just point and shoot.
[
Program AE Modes
Auto
The camcorder adjusts focus, exposure and other settings
automatically. However, you have the option of adjusting the
settings manually.
57
Sports
Use this mode to record sports scenes (such as tennis or golf),
E
moving objects (such as roller coasters) or when recording from a
moving car.
❍ This mode is set at a high shutter speed and should therefore be used in sufficient
light.
❍ This mode is mainly intended for frame-by-frame or slow playback. The picture may
not appear smooth when played back in normal speed.
Portrait
Use this mode to give accent to your subject by blurring the
background or foreground.
❍ The blur effect increases the more you zoom to telephoto.
❍ This mode is set at a higher shutter speed. The picture may not
appear smooth when played back.
Using the Full Range
of Features
Spotlight
Use this mode to record spotlit scenes such as shows, recitals or
fireworks.
Sand & Snow
Use this mode in bright places such as a sunny beach or ski resort. It
prevents the subject from being underexposed.
❍ The subject may become overexposed in dark surroundings. Check
the image on the screen.
❍ This mode is set at a higher shutter speed. The picture may not appear smooth when
played back.
Low Light
Use this mode to record in dimly lit places. The shutter is fixed at a
slow shutter speed.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ The camcorder may have difficulty to focus automatically.
58
Night
Use this mode to record in dark places. The shutter speed is
adjusted automatically. It is useful when recording in places with
changing light conditions (such as in amusement parks).
E
❍ ZR70 MC ZR65 MC Night mode cannot be used in CARD CAMERA
mode.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus
manually.
ZR70 MC
Super Night (CAMERA mode)
In CAMERA mode, use this mode to record in very dark places. The
shutter speed is adjusted automatically. The White LED lights up
automatically illuminating the subject in the center of the screen,
allowing you to record brightly in color.
Using the Full Range
of Features
Low Light Plus (CARD CAMERA mode)
In CARD CAMERA mode, use this mode to record in dark places.
The shutter is fixed at a slow shutter speed. The White LED lights up
illuminating the subject in the center of the screen, allowing you to
record brightly in color.
❍ The range of the White LED is limited. Check the image on the screen when
recording.
❍ Use this mode for recordings at close range (up to 6.6 ft (2m)).
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus
manually.
59
Selecting the Program AE Mode
CAMERA
E
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Slide the program selector to Q (program AE).
2. Press the selector dial.
A list of the program AE modes appears.
3. Select a mode and press the selector dial.
Using the Full Range
of Features
The symbol of the mode appears on the upper left corner of the
screen.
(Auto) disappears after 4 seconds.
60
❍ Do not change the mode during recording as the brightness of the image may
change abruptly.
❍ The setting resets to the Auto mode when you switch the program selector to
[.
❍ Bright light in a dark scene may cause a vertical light bar to appear. This is not
a malfunction.
Using Digital Effects
You can use the digital effects during recording and playback.
Faders (
62): Begin or end scenes with a fade to or from black.
Effects (
65): Add flavor to your recordings.
Multi-image screen (
E
67)
Availability of Digital Effects by Operating Modes:
CAMERA
PLAY (VCR)
ZR70 MC/ZR65 MC: ZR70 MC/ZR65 MC:
CARD CAMERA CARD PLAY (VCR)
Movies
Still Images
Faders
h
i
h
i
i
Effects
h
h
h
h*1
i
Multi-image
screen
h*2
h*2
h
i
i
h: Available i: Not available
*1: Black and White only
*2: Cannot be used in Night and Super Night (ZR70 MC) mode.
Using the Full Range
of Features
❍ Turn off the digital effect when you do not use it.
Press the DIGITAL EFFECTS button to open the menu. Select [D.EFFECTS |]
and press the ON/OFF button.
❍ The camcorder retains the setting even if you turn it off or change the program
AE mode.
❍ The digital effect turns off if you switch the program selector to [.
❍ Digital effects can be selected but not activated on a blank blue screen
(appears in PLAY (VCR) mode).
❍ Digital effects activated during playback do not change the recording.
❍ Digital effects cannot be used during DV dubbing and photo/date search.
❍ Digital effects can also be set with the wireless controller.
61
Faders
Fade Trigger (FADE-T)
E
The image gradually fades in.
The image gradually fades out.
Wipe (WIPE)
The image begins as a vertical
line in the center and
expands sideways until
it fills the whole screen.
The image is wiped off from the
sides of the screen.
Using the Full Range
of Features
Corner Wipe (CORNER)
The image appears from the
corners until it fills the
whole screen.
The image is wiped off from the
corners.
Jump (JUMP)
A small image appears from
the left, jumps into the
center and enlarges
until it fills the whole
screen.
The image shrinks, jumps from
the center to the left and
disappears.
Flip (FLIP)
The image flips into the screen.
The image flips out of the screen.
62
Puzzle (PUZZLE)
The image appears in 16 pieces.
The pieces move
around until the
puzzle is solved.
E
The image is divided into 16
pieces. The pieces move around
and disappear.
Zigzag (ZIGZAG)
The image appears in zigzag
from the top of the
screen.
Black stripes appear in zigzag
from the bottom of the screen
until they cover the whole image.
The screen turns yellow, forms
a beam that becomes
thinner and the image
appears.
A yellow beam appears in the
center of the screen and expands
until it covers the whole image.
Using the Full Range
of Features
Beam (BEAM)
Tide (TIDE)
The image appears from
both sides like tides.
The image disappears from both
sides like tides.
63
Selecting a Fader
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
1. In CAMERA mode, set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
DIGITAL
EFFECTS
3. Select [FADER].
4. Select the fader option.
5. Press the DIGITAL EFFECTS button.
The name of the selected fader flashes.
Using the Full Range
of Features
CAMERA mode:
6. Fade in: In record pause mode, press the ON/OFF
button and begin recording by pressing the
start/stop button.
Fade out: During recording, press the ON/OFF button
and pause recording by pressing the start/stop button.
ON/OFF
The fader can be activated/deactivated by pressing the ON/OFF button.
PLAY (VCR) mode:
6. Fade in: In playback pause mode, press the ON/OFF
button and begin playback by pressing the e/a
button.
Fade out: During playback, press the ON/OFF button
and pause playback by pressing the e/a button.
ON/OFF
The fader can be activated/deactivated by pressing the ON/OFF button.
ZR70 MC ZR65 MC Faders cannot be selected when Card Mix is activated.
64
Effects
Art (ART)
The image becomes like a paint (solarization).
E
Black and White (BLK & WHT)
The image becomes black and white.
Sepia (SEPIA)
The image becomes monochrome with a brownish tint.
Mosaic (MOSAIC)
The image is blurred through enlarging the size of some pixels.
Ball (BALL)
The image becomes like a ball.
The image becomes a cube and rotates.
Using the Full Range
of Features
Cube (CUBE)
Wave (WAVE)
Both ends of the image sway in waves.
Color Masking (COLOR M.)
The image becomes a rhombus surrounded by a masking frame that
changes the colors.
Mirror (MIRROR)
Creates a symmetrical image as if there would be a mirror in the
center of the screen.
ZR70 MC ZR65 MC Only Black and White can be used in CARD CAMERA mode.
65
Selecting an Effect
PLAY (VCR)
CAMERA
CARD CAMERA
CARD PLAY (VCR)
E
1. Press the DIGITAL EFFECTS button.
[D.EFFECTS OFF], [FADER], [EFFECT] and [MULTI-S] appear.
DIGITAL
EFFECTS
2. Select [EFFECT].
3. Select the effect.
4. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
The name of the selected effect flashes.
Using the Full Range
of Features
5. Press the ON/OFF button.
• The name of the selected effect stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
ZR70 MC ZR65 MC
ON/OFF
Selecting an Effect in CARD CAMERA Mode
CAMERA
PLAY (VCR)
CARD CAMERA
1. Press the DIGITAL EFFECTS button.
“BLK&WHT” flashes.
CARD PLAY (VCR)
DIGITAL
EFFECTS
2. Press the ON/OFF button.
• “BLK&WHT” stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
66
ON/OFF
Using the Multi-Image Screen
The multi-image screen captures moving subjects in 4, 9 or 16 sequences of still images
with the Image Capture feature and displays them at one time. Sound will be
recorded normally. This feature can be used in CAMERA and PLAY (VCR) mode.
E
You can choose the transition speed at which to capture the subject from manual, fast
(every 4 frames), moderate (every 6 frames*) or slow (every 8 frames*).
* In Low Light mode: moderate (every 8 frames), slow (every 12 frames).
Selecting the Multi-Image Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
Using the Full Range
of Features
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
3. Select [MULTI-S].
[S.SPEED] and [S.SPLIT] appears.
4. Select [S.SPEED].
[MANUAL], [FAST], [MOD.] and [SLOW] appear.
5. Select the transition speed.
6. Select [MULTI-S] again.
[S.SPEED] and [S.SPLIT] appears.
7. Select [S.SPLIT].
[4], [9], [16] settings appear.
8. Select the number of sequences.
9. Press the DIGITAL EFFECTS button.
[MULTI-S] flashes.
DIGITAL
EFFECTS
67
Capturing
10.Press the ON/OFF button.
E
• MANUAL: Images will be captured each time you press the ON/OFF button. The blue
frame indicating the next sequence disappears after the last image. To cancel the last
captured image, press and hold the ON/OFF button. To cancel the multi-image screen,
press and release the ON/OFF button.
• FAST, MODERATE, SLOW: The set number of images will be captured at the set speed.
To cancel the multi-image screen, press the ON/OFF button.
11.Press the start/stop button begin recording.
Using the Full Range
of Features
The multi-image screen is recorded on the tape.
68
❍ The multi-image screen cannot be operated in Night and Super Night (ZR70
MC) mode.
❍ You can operate the multi-image screen only in the following playback modes:
- When [S.SPEED] is set to [MANUAL]: Playback pause, slow forward/reverse
playback
- When [S.SPEED] is set to [FAST], [MOD.] or [SLOW]: Playback pause
❍ The multi-image screen can be operated in record or record pause mode.
❍ ZR70 MC ZR65 MC The multi-image screen cannot be selected when Card Mix is
activated.
❍ In PLAY (VCR) mode: Pressing any tape operation button (such as play or
pause), or performing date/photo search cancels the multi-image screen.
Turning Off the Image Stabilizer
The image stabilizer allows you to obtain steady recordings even at telephoto. There is
no need to turn off the image stabilizer during normal recording. However, the
camcorder tries to compensate for horizontal movements and you may therefore
E
decide to turn it off during panning. The image stabilizer cannot be turned off when
the program selector is set to [.
CAMERA
(
44)
PLAY (VCR)
CAMERA SET UP
CARD CAMERA
IMAGE S.
CARD PLAY (VCR)
••ON
Open the menu and select [CAMERA SET UP]. Select [IMAGE S. i], set it
to [OFF] and close the menu.
i disappears.
Using the Full Range
of Features
❍ We recommend turning off the image stabilizer when you mount the
camcorder on a tripod.
❍ The image stabilizer is designed to compensate a normal degree of camcorder
shake.
❍ ZR70 MC ZR65 MC The image stabilizer cannot be used in CARD CAMERA
mode.
❍ The image stabilizer might not be as effective in Low Light, Night and Super
Night (ZR70 MC) mode.
69
Recording With the Self-Timer
E
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
PHOTO
button
(self-timer)
button
Start/stop button
SELF T. button
PHOTO button
Start/stop button
1. Press the
Using the Full Range
of Features
“
(self-timer) button.
DATA
CODE
” appears.
When recording movies
2. Press the start/stop button.
The camcorder starts recording after a 10-second countdown (2
seconds when using the wireless controller). The count down
appears on the screen.
CAMERA
OFF
PLAY
(VCR)
3. Press the start/stop button to stop recording.
The camcorder returns to record pause mode
When recording still images
2. Press the PHOTO button.
OT
PH
• The camcorder adjusts the focus 2 seconds before recording
begins. F flashes in white and turns green when focus and
exposure are adjusted.
• The camcorder records the still image for approx. 6 seconds
and returns to record pause mode (ZR70 MC/ZR65 MC: In CARD CAMERA mode, it
displays the still image when recording is complete).
O
❍ To cancel the self-timer, press the
(self-timer) button, start/stop button
(when recording movies) or PHOTO button (when recording still images).
❍ The self-timer will be canceled when you turn off the camcorder.
70
Audio Recording
Changing the Audio Mode
You can record sound in two audio modes—16-bit and 12-bit. The 12-bit mode records
E
sound on two channels (stereo 1), leaving 2 channels free (stereo 2) for adding new
sound later. Select the 16-bit mode for higher sound quality.
CAMERA
(
44)
CARD CAMERA
PLAY (VCR)
AUDIO SET UP
CARD PLAY (VCR)
AUDIO MODE••12bit
Open the menu and select [AUDIO SET UP]. Select [AUDIO MODE], set it to
[16bit] and close the menu.
“16 bit” appears for approximately 4 seconds.
For adding new sound, see Audio Dubbing (
96).
Recording with an External Microphone
Using the Full Range
of Features
You can use an external microphone for
recording. Almost all stereo microphones with
a plug diameter of 0.14 inch (3.5 mm) can be
connected to the MIC terminal. Use a
microphone with a built-in power supply
(condenser microphone).
MIC
❍ The audio level differs from that of the built-in microphone.
❍ Be careful with long microphones as they may appear in the picture.
❍ ZR70 MC See also Using the DM-50 Microphone (
74).
Wind Screen
You can reduce the wind noise when recording in windy places.
CAMERA
(
44)
PLAY (VCR)
AUDIO SET UP
CARD CAMERA
CARD PLAY (VCR)
WIND SCREEN•OFF
Open the menu and select [AUDIO SET UP]. Select [WIND SCREEN], set it
to [ON] and close the menu.
“WS ON” appears when you turn the wind screen on.
71
Using the Full Range
of Features
E
72
❍ Low sound may be reduced together with the wind noise. We recommend
turning off the wind screen for normal recordings.
❍ The wind screen function cannot be turned on/off during recording.
❍ The wind screen function can also be used for audio dubbing (when [AUDIO
DUB.] is set to [MIC. IN] in the [AUDIO SET UP] submenu).
❍ The wind screen function cannot be used when an external microphone is
connected to the MIC terminal (ZR70 MC: or when the DM-50 Microphone is
attached to the advanced accessory shoe).
ZR70 MC
Using the VL-3 Video Light (Optional)
This video light enables you to record brightly in color even in dark places. This VL-3
Video Light attaches to the camcorder’s
advanced accessory shoe for cable-free
operation and is powered by the camcorder’s power supply.
E
Refer also to the VL-3 Video Light instruction manual.
❍ Always turn off the camcorder before attaching/removing the video light.
❍ Do not touch or place flammable material or plastic close to the lamp or the
surrounding parts during or immediately after use; they become very hot.
❍ Do not look directly at the lamp while the video light is on.
❍ Do not carry the camcorder by the video light.
1. Slide the video light into the
accessory shoe until it clicks.
q
LOCK
2. Tighten the fastening screw.
Be careful that the video light does not come
off when tightening the screw.
3. Set the camcorder to CAMERA or
CARD CAMERA mode.
•
(Connection) appears.
• ON: The video light stays on.
• AUTO: The video light turns on and off
automatically.
e
w
CAMERA
OFF
PLAY
(VCR)
CK
LO
LOCK
Using the Full Range
of Features
4. Turn the video light’s power switch
to AUTO or ON.
r
AU
OF
LO
TO O N
F
CK
73
ZR70 MC
E
Using the DM-50 Microphone (Optional)
The high sensitive Directional Stereo Microphone DM-50 attaches to the
advanced accessory shoe for cable-free operation and is powered by the camcorder’s
power supply. Use it for recording or dubbing audio.
Refer also to the DM-50 Microphone instruction manual.
❍ Always turn the camcorder off before attaching/removing the microphone.
❍ Do not connect any microphone to the MIC terminal when the DM-50
Microphone is connected.
❍ Do not carry the camcorder by the microphone.
1. Slide the microphone into the
accessory shoe until it clicks.
2. Tighten the fastening screw.
Be careful that the microphone does not
come off when tightening the screw.
Using the Full Range
of Features
3. Set the camcorder to CAMERA or
CARD CAMERA mode.
(Connection) appears.
q
e
4. Set the microphone’s directivity
switch.
• SHOTGUN: For recording clear sound from
the front (monaural).
• STEREO 1: For recording sound from the
front and surrounding area.
• STEREO 2: For recording surrounding
sound in a wider range than in
STEREO 1.
CAMERA
OFF
PLAY
(VCR)
r
w
74
Adjusting the Focus Manually
Some subjects may not be suitable for autofocus. In such case, focus manually.
E
Autofocus may not work well on the following subjects:
Reflective surfaces
Subjects with
low contrast
(e.g. White Wall)
Fast Moving Subjects
Horizontal Stripes
Through dirty or
wet windows
Different Distances
Dark Subjects
Night Scenes
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
Using the Full Range
of Features
1. Set the program selector to Q.
2. Adjust the zoom.
When you operate the zoom after adjusting the focus, the
subject may not stay in focus. Adjust the zoom before the focus.
3. Press the FOCUS button.
“MF” appears in light blue.
FOCUS
4. Turn the selector dial to adjust the focus.
• Turn the selector dial up or down until the image appears
focused.
• If “AE ±0” appears in light blue, focus cannot be adjusted.
Press the FOCUS button again to display “MF” in light blue.
75
5. Press the FOCUS button to return to autofocus.
FOCUS
E
The setting resets to autofocus when you switch the program selector to [.
Infinity Focus
Use this function when you wish to focus on faraway subjects such as mountains or
fireworks.
Press the focus button more than 3 seconds in step 3.
Using the Full Range
of Features
“MF ∞” appears. When you operate the zoom or turn the selector dial when “MF ∞” is
displayed in light blue, “∞” disappears and the camcorder changes to manual focus.
76
Adjusting the AE Shift
You can adjust the AE (auto exposure) function to lighten or darken the image. This
allows you to compensate for backlit or overexposed scenes. Available Levels: –2 to +2,
in 0.25 intervals (excluding –1.75 and +1.75).
CAMERA
PLAY (VCR)
E
CARD PLAY (VCR)
CARD CAMERA
1. Set the program selector to Q.
2. Set the program AE mode to
Auto,
Sports,
Light or
Low Light Plus (ZR70 MC) mode.
Portrait,
Low
3. Press the AE SHIFT button.
“AE ±0” appears in light blue.
AE SHIFT
• Turn the selector dial up to lighten the image and down to
darken the image.
• If “MF” is displayed in light blue, AE shift cannot be adjusted.
Press the AE SHIFT button again to display “AE ±0” in light blue.
❍ The camcorder retains the setting even if you turn it off or change the program
AE mode.
❍ The camcorder resets to the auto setting when you switch the program
selector to [.
Using the Full Range
of Features
4. Turn the selector dial to adjust the AE shift level.
77
Setting the Shutter Speed
E
In the
Auto mode, you can adjust the shutter speed manually to make stable shots
of fast moving subjects.
CAMERA
(
44)
PLAY (VCR)
CAMERA SET UP
CARD CAMERA
CARD PLAY (VCR)
SHUTTER•••••AUTO
1. Set the program selector to Q.
2. Set the program AE mode to the
(AUTO) mode.
3. Open the menu and select [CAMERA SET UP].
4. Select [SHUTTER].
5. Select the shutter speed and press the selector dial.
Using the Full Range
of Features
CAMERA Mode
78
AUTO
1/60
1/100
1/250
1/500
1/1000
1/2000
ZR70 MC , ZR65 MC
CARD CAMERA Mode
AUTO
1/60
1/100
1/250
6. Close the menu.
❍ Do not point the camcorder directly at the sun when the shutter speed is set to
1/1000 or higher.
❍ The image may flicker when recording with high shutter speeds.
❍ The setting resets to the auto setting when you switch the program selector to
[, or change the program AE mode.
❍ ZR70 MC ZR65 MC If the shutter speed is set to 1/500 or higher in CAMERA
mode and you switch to CARD CAMERA mode, it automatically changes to
1/250.
❍ Recording under fluorescent lights: When the camcorder is set to [ (Easy
Recording) or when the program AE mode is set to Auto, Night or Super Night
(ZR70 MC) mode, it automatically detects the flicker of fluorescent lighting and
adjusts the shutter speed accordingly. However, if the brightness of the screen
starts to flicker, select Auto mode and set the shutter speed to 1/100.
❍ Guidelines for Recording with High Shutter Speeds:
- Outdoor sports such as golf or tennis: 1/2000
E
- Moving objects such as cars or roller coasters: 1/1000,
1/500 or 1/250
- Indoor sports such as basketball: 1/100
Using the Full Range
of Features
79
Setting the White Balance
E
The camcorder’s auto white balance system adjusts the colors to appear natural for
different lighting conditions. However, you can use the preset modes to reproduce
colors more accurately, or set a custom white balance to obtain the optimal setting.
Zoom lever
White sheet or paper
Program selector
Using the Full Range
of Features
Selector dial
80
❍ When the program selector is set to [, white balance is preset to [AUTO].
Indoor, outdoor and custom white balance cannot be selected.
❍ The camcorder retains the setting even if you turn it off.
❍ When you have set the custom white balance:
- Reset the white balance when the lighting condition changes.
- Turn off the digital zoom.
❍ Setting the white balance manually may provide better results in the following
cases.
- Changing lighting conditions
- Close-ups
- Subjects in a single color (sky, sea or forest)
- Under mercury lamps or certain types of fluorescent lights
❍ Use the T Indoor or U Outdoor mode in the following cases:
T Indoor:
- Changing lighting condition
- Under video light
- Under sodium lamps
U Outdoor Mode
- For night scenes or fireworks
- Sunrise or sunset
* Use the auto setting for normal outdoor scenes.
CAMERA
(
44)
PLAY (VCR)
CAMERA SET UP
CARD CAMERA
CARD PLAY (VCR)
WHITE BAL.••AUTO
E
For T (Indoor) or U (Outdoor) Setting:
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SET UP].
3. Select [WHITE BAL.].
4. Select T (indoor) or U (outdoor).
T or U appears.
5. Close the menu.
For Custom White Balance:
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SET UP].
3. Select [WHITE BAL].
• W flashes and stops flashing when settings is complete.
• Depending on the light source, W may keep flashing. The result will still be better
than with the auto setting.
5. Close the menu.
Using the Full Range
of Features
4. Point the camcorder at a white object (such as a sheet of paper), zoom
in until it fills the whole screen and select [SET W].
81
Magnifying the Image
E
The playback image can be magnified by 2 times.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Move the zoom lever toward T.
• The image is magnified by 2 times.
• A frame appears indicating the position of the enlarged part.
2. Move the image.
• Turn the selector dial to move the image to the right and left,
or up and down. Pressing the selector dial switches between
the directions.
• To cancel the magnification, move the zoom lever toward W.
Using the Full Range
of Features
ZR70 MC Movies played back from a memory card cannot be magnified.
82
Displaying the Data Code
Once date and time are set, the camcorder maintains a data code containing
recording date and time and other camera data such as shutter speed and exposure
(f-stop). (ZR70 MC/ZR65 MC: Only date and time appear when playing back a memory
E
card).
DATA CODE button
Controller buttons
MENU button
DATA CODE
button
MENU button
Selector dial
Using the Full Range
of Features
❍ The data code display turns off when you turn the camcorder off.
❍ The data code may not be displayed if a recording made with this camcorder is
played back on a different digital camcorder.
❍ The data code cannot be displayed in frame advance/reverse playback. Camera
data may not appear in some special playback modes.
❍ When the TV screen displays are hidden (
134), the displays still appear on
the LCD screen. If you turn on the data code, displays other than the data
code will disappear from the LCD screen.
Available Data Code Combinations (in PLAY (VCR) mode):
DATA CODE
(tape only)
Date/Time
Camera data
D/TIME SEL.
Date
Time
Date & Time
Date/Time &
Camera data
JAN. 1,2003
F1.8
1/250
F1.8
1/250
JAN. 1,2003
12:00:00 PM
F1.8
1/250
F1.8
1/250
12:00:00 PM
12:00 PM
JAN. 1,2003
F1.8
1/250
F1.8
1/250
12:00 PM
JAN. 1,2003
83
Selecting the Date/Time Display Combination
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
(
44)
DISPLAY SET UP
D/TIME SEL.•DATE & TIME
Open the menu and select [DISPLAY SET UP]. Select [D/TIME SEL.], set it to
[DATE] or [TIME] and close the menu.
Selecting the Data Code Display Combination
CAMERA
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
CARD PLAY (VCR)
DATA CODE•••DATE/TIME
Open the menu and select [DISPLAY SET UP]. Select [DATA CODE], set it to
[DATE/TIME], [CAMERA DATA] or [CAM. & D/T] and close the menu.
Using the Full Range
of Features
Displaying the Data Code
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
Press the DATA CODE button.
Only date and time appear in CARD PLAY (VCR) mode.
Six-Second Auto Date
Date and time appear for 6 seconds when you begin playback, or to indicate that date
or time zone has changed.
CAMERA
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
CARD PLAY (VCR)
6SEC.DATE•••OFF
Open the menu and select [DISPLAY SET UP]. Select [6SEC.DATE], set it to
[ON] and close the menu.
84
Photo Search/Date Search
You can search for a still image recorded
SEARCH SELECT button
anywhere on the tape with the photo search
function, or locate the change of the
E
Search buttons
date/time zone with the date search function.
STOP 3 button
CAMERA
PLAY (VCR)
CARD CAMERA
1. Press the SEARCH SELECT button to choose between
photo search and date search.
“PHOTO SEARCH” or “DATE SEARCH” appears.
2. Press the + or - button to begin searching.
INDEX SLIDE SHOW
CARD
DATA CODE SEARCH SELECT
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
INDEX SLIDE SHOW
FF
CARD
DATA CODE SEARCH SELECT
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
FF
• Press the 3 (stop) button stop searching.
Using the Full Range
of Features
• Press the + button to search forward and the - button to
search backward.
• Press more than once to search for further still images or date
changes (up to 10 times).
• Press the + or - button to change the search direction.
CARD PLAY (VCR)
❍ Photo search: A still image recorded very close to the point you start the search
may not be detected.
❍ Date search: A recording of longer than a minute per date/area is required.
❍ Date search: Playback may start slightly before or after the date change.
❍ Date search may not function if the data code is not correctly displayed.
85
Returning to a Pre-marked Position
E
If you wish to return to a particular scene
later, mark the point with the zero set
memory and the tape will stop at that point
when you rewind/fast forward the tape.
CAMERA
PLAY (VCR)
REW ` button
ZERO SET
MEMORY
button
CARD CAMERA
1. Press the ZERO SET MEMORY button at the point
you wish to return to later.
• “0:00:00 ” appears.
• To cancel, press the ZERO SET MEMORY button again.
PLAY e button
FF 1 button
STOP 3 button
CARD PLAY (VCR)
INDEX SLIDE SHOW
CARD
DATA CODE SEARCH SELECT
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
FF
Using the Full Range
of Features
2. When you have finished playback, fast forward or
rewind the tape.
86
• “RTN 1” or “` RTN” appears.
• The tape stops automatically at “0:00:00”.
• The tape counter changes to time code.
❍ Time code and tape counter display may not match accurately.
❍ The zero set memory may not function correctly when blank sections exist on
the tape.
❍ If you remove the tape, the zero set memory is canceled and the counter
display shows the time code.
Recording to a VCR or Digital Video Device
You can copy your recordings by connecting the camcorder to a VCR or a digital video
device. If you connect a digital video device, you can copy recordings with virtually no
generation loss in image and sound quality.
E
When connecting a VCR:
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting (
39).
❍ The quality of the edited tape will be slightly lower than that of the original.
When connecting a digital video device:
❍ You can connect only one device to the camcorder with the DV cable.
❍ Blank sections may be recorded as anomalous picture.
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
Example: Recording to a VCR
CAMERA
CARD CAMERA
PLAY (VCR)
CARD CAMERA
1. Connect the camcorder to the VCR.
See Playing Back on a TV Screen (
41).
2. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
3. Connected device: Load a blank cassette and set the device to record
pause mode.
Editing
4. Locate the scene you wish to copy and pause playback shortly before
the scene.
5. Play back the tape.
6. Connected device: Begin recording when the scene you wish to copy
appears. Stop recording when copying is complete.
7. Stop playback.
87
Connecting a Digital Video Device
Refer also to the instruction manual of the digital video device.
E
Side with an arrow
Signal flow
Editing
Commercially available DV cable
88
Recording from Analog Video Devices (VCR, TV or Camcorder)
You can record videos or TV programs from a VCR or analog camcorder on the tape in
the camcorder.
E
❍ Anomalous signals sent from the connected device may be recorded as
anomalous picture (although it may not appear so on the screen), or it may not
be recorded at all.
❍ You cannot record from tapes with copyright protective signals.
❍ Headphones cannot be used during analog line-in recording. If the
AV/headphones terminal set to [PHONES H], it will automatically switch to [AV].
CAMERA
CARD CAMERA
PLAY (VCR)
CARD CAMERA
1. Connect the camcorder to the analog video device.
See Playing Back on a TV Screen (
41).
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button on the wireless
controller.
In record pause mode and during recording, you can check the
picture on the screen.
AV INSERT AV DV REMOTE SET
REC
PAUSE
WIRELESS CONTROLLER WL-D79
5. Connected device: Play back the tape.
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
FF
SLOW
2
Editing
6. Press the PAUSE a button on the wireless controller
when the scene you wish to record appears.
AV INSERT AV DV REMOTE SET
7. Press the STOP 3 button on the wireless controller to
stop recording.
• Press the PAUSE a button on the wireless controller to pause
recording.
• Press the PAUSE a button again to restart recording.
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
FF
2
AV INSERT AV DV REMOTE SET
8. Connected device: Stop playback.
89
Recording from Digital Video Devices (DV Dubbing)
E
You can record from other digital video devices equipped with a DV terminal with
virtually no loss in picture and sound quality.
❍ When recording from digital video devices, make sure that “AV \ DV” is not
displayed on the screen. If “AV \ DV” is displayed, change the setting
(
93).
❍ Anomalous signals sent from the connected device may be recorded as
anomalous picture (although it may not appear so on the screen), or it may not
be recorded at all.
❍ Copyright protected signals cannot be recorded.
❍ Blank sections may be recorded as anomalous picture.
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
❍ You can connect only one device with the DV cable.
❍ You can use the camcorder for playback and recording without reconnecting
the DV cable.
CAMERA
CARD CAMERA
PLAY (VCR)
CARD CAMERA
1. Connect the camcorder to the digital video device.
Editing
See Connecting a Digital Video Device (
88).
2. Set the camcorder to PLAY (VCR) mode and load a
blank cassette.
AV INSERT AV DV REMOTE SET
REC
PAUSE
WIRELESS CONTROLLER WL-D79
“DV IN” appears.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button on the wireless controller.
In record pause mode and during recording, you can check the picture on the screen
5. Connected Device: Play back the tape.
6. Press the PAUSE a button on the wireless controller
when the scene you wish to record appears.
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
FF
SLOW
2
AV INSERT AV DV REMOTE SET
7. Press the STOP 3 button on the wireless controller to
stop recording.
• Press the PAUSE a button on the wireless controller to pause
recording.
• Press the PAUSE a button again to restart recording.
8. Connected Device: Stop playback.
90
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
FF
2
AV INSERT AV DV REMOTE SET
Copyright Signal
Certain software tapes are copyright protected. If you attempt to play back such tape,
“COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears and you will not be able
to view the contents of the tape. If you attempt to record from such tape via the DV
terminal, “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears and you will not
E
be able to record the contents of the tape.
Editing
91
Converting Analog Signals into Digital
Signals (Analog-Digital Converter)
E
By connecting the camcorder to a VCR or 8mm video camcorder, you can convert
analog video/audio signals to digital signals and output the digital signals via the DV
terminal. The DV terminal serves as output terminal only.
❍ Headphones cannot be used during analog-digital conversion.
❍ Unload the tape from the camcorder.
❍ Turn off all devices before starting the connections.
❍ Depending on the signal sent from the connected device, the conversion from
analog to digital signals might not work properly (e.g., signals that include
copyright protective signals or anomalous signals such as ghost signals, etc.)
We recommend powering the camcorder from a household power source.
Connecting the Devices
This illustration shows how to connect using a S-video cable. You can also connect the
yellow plug of the stereo video cable to the VIDEO terminal. Refer also to the
instruction manual of the connected device.
OUTPUT
S
Signal flow
S(S1)-VIDEO
Editing
S-150 S-video Cable (optional)
VIDEO
L
AV
Signal flow
STV-250N Stereo Video
Cable (supplied)
DV
Signal flow
Commercially available DV cable
92
AUDIO
R
Turning On the Analog-Digital Converter
CAMERA
CARD CAMERA
PLAY (VCR)
CARD CAMERA
Press the AV \ DV button on the wireless controller.
E
OR
(
44)
VCR SET UP
AV
DV OUT••OFF
Open the menu and select [VCR SET UP]. Select [AV \ DV OUT], set it to
[ON] and close the menu.
❍ For normal use, set [AV \ DV OUT] to [OFF] (so that “AV \ DV” does not
appear on the screen). If it is set to [ON], digital signals cannot be input via the
camcorder’s DV terminal.
❍ Depending on the software and the specifications of your computer, you may
not be able to transfer converted signals via the DV terminal.
Editing
93
Replacing Existing Scenes (AV Insert)
E
You can insert and replace images/audio on the tape of the camcorder with
images/audio from other video devices connected via AV terminal or DV terminal.
Scene to be inserted
Playback tape
Insert start
Insert end
Tape in the
camcorder
before inserting
Tape in the
camcorder after
inserting
Editing
Inserted scene
94
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting (
39).
❍ You cannot insert from a TV program when the synchronized signals are
distorted.
Camcorder:
❍ Use only tapes recorded in SP mode.
❍ AV insert will stop if the camcorder detects a blank section or a section not
recorded in SP mode on the tape.
Connected device:
❍ Use only tapes without blank sections.
❍ AV insert may not work correctly if the tape has a blank section or changes in
the recording mode.
❍ AV insert cannot be performed when the quality of the recording is poor, or
during special playback such as fast forward, rewind, playback pause, slow
playback etc.
Example: AV Insert from a VCR
CAMERA
CARD CAMERA
PLAY (VCR)
CARD CAMERA
E
1. Connect the camcorder to the VCR.
See Playing Back on a TV Screen (
41).
2. VCR: Load a recorded cassette. Locate the scene you wish to insert and
pause playback shortly before the scene.
3. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
Make sure the tape-protect switch is set to allow recording.
4. Locate the scene you wish to replace and pause playback shortly before
the scene.
You can use the playback buttons on the camcorder or the special playback buttons on
the wireless controller.
5. Press the AV INSERT button on the wireless
controller.
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
“AV INSERT” and “2a” appear.
REC
PAUSE
6. VCR: Play back the tape.
7. Press the PAUSE a button on the wireless controller
when the scene you wish to insert appears.
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
FF
SLOW
2
AV INSERT AV DV REMOTE SET
Press the PAUSE a button on the wireless controller to pause
inserting.
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
Editing
8. Press the STOP 3 button on the wireless controller
to stop inserting.
FF
2
AV INSERT AV DV REMOTE SET
9. VCR: Stop playback.
Set the zero set memory at the end of the scene you wish to replace. The
camcorder will automatically stop AV insert at that point.
95
Audio Dubbing
E
You can add sound from audio devices (AUDIO IN) or with the built-in or an external
microphone (MIC. IN).
❍ Use only tapes recorded in SP mode 12-bit audio sound with this camcorder.
Audio dubbing will stop if the tape has a blank section or a section recorded in
LP mode, 16-bit or 12-bit 4-channel sound. In above case, create a copy in SP
mode 12-bit audio sound using the analog line-in function.
❍ Do not connect/disconnect any cable to/from the camcorder while dubbing.
❍ You cannot use the DV terminal for audio dubbing.
❍ If you add sound to a tape not recorded with this camcorder, sound quality
may decrease.
❍ Sound quality may decrease when you add sound to the same scene for more
than 3 times.
Editing
Connecting an Audio Device
AV
Signal flow
STV-250N Stereo Video Cable
(supplied)
L
R
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting (
39).
❍ You can monitor the picture on the LCD screen or a TV connected via the
S-video terminal, and check the sound with the built-in speaker.
96
Using a Microphone
E
MIC
❍ When using the built-in microphone: do not connect any cables to the
microphone terminal or the accessory shoe.
❍ When using an external microphone: Connect it to the microphone terminal.
❍ ZR70 MC When using the DM-50 Microphone: Do not connect any cables to
the microphone terminal.
❍ When you connect a TV via the S-video terminal, you can check the picture on
the TV screen and the sound with headphones connected to the camcorder.
When you connect a TV via the AV terminal, you can check the picture on the
TV screen but you cannot check the sound with headphones.
Dubbing
CAMERA
(
44)
PLAY (VCR)
AUDIO SET UP
CARD CAMERA
CARD CAMERA
AUDIO DUB.••AUDIO IN
2. Open the menu and select [AUDIO SET UP]. Select
[AUDIO DUB.], set it to [AUDIO IN] or [MIC. IN] and
close the menu.
Editing
1. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
3. Locate the scene you wish audio dubbing to start.
4. Press the PAUSE a button on the wireless controller.
5. Press the AUDIO DUB. button on the wireless
controller.
• “AUDIO DUB.” and “
” appear.
• ZR70 MC If the optional DM-50 microphone is attached,
(Connection) appears.
6. Press the PAUSE a button on the wireless controller
to begin dubbing.
• Audio device: Begin playback.
• Microphone: Direct your voice to the microphone.
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
REC
PAUSE
ZERO SET
MEMORY REW
PLAY
12bit
AUDIO OUT
STOP
AUDIO DUB. PAUSE
SLOW
FF
2
AV INSERT AV DV REMOTE SET
97
7. Press the STOP 3 button on the wireless controller
to stop dubbing.
PLAY
STOP
AUDIO DUB. PAUSE
Audio device: Stop playback.
E
ZERO SET
MEMORY REW
12bit
AUDIO OUT
SLOW
FF
2
AV INSERT AV DV REMOTE SET
Set the zero set memory at the end of the scene you wish to dub audio. The
camcorder will automatically stop audio dubbing at that point.
Playing Back the Added Sound
You can select to play back Stereo 1 (original sound), Stereo 2 (added sound), or adjust
the balance of both sounds.
MENU button
12bit AUDIO
OUT button
Selector dial
CAMERA
Editing
(
44)
PLAY (VCR)
AUDIO SET UP
CARD CAMERA
CARD CAMERA
12bit AUDIO•STEREO1
1. Open the menu and select [AUDIO SET UP]. Select [12bit AUDIO OUT],
select a setting and close the menu.
• STEREO 1: Plays back the original sound.
• STEREO 2: Plays back the added sound.
• MIX/FIXED: Plays back stereo 1 and stereo 2 in the same level.
• MIX/VARI.: Plays back stereo 1 and stereo 2. The mix balance can be adjusted.
2. If you have selected [MIX/VARI.], adjust the mix level: Open the menu
and select [AUDIO SET UP]. Select [MIX BALANCE], adjust the balance
with the selector dial and close the menu.
Turn the selector dial down to increase the volume of Stereo 1 and up to increase the
volume of Stereo 2.
❍ The camcorder resets to [STEREO 1] when you turn the camcorder off.
However, the mix balance is memorized by the camcorder.
❍ You can also press the 12bit AUDIO OUT button on the wireless controller to
select the audio output. However, the mix balance can only be adjusted in the
menu.
98
Connecting to a Computer Using a DV (IEEE1394) Cable
You can transfer recordings to a computer equipped with a DV (IEEE1394) terminal or
IEEE1394 capture board (optional software required).
E
DV
IEEE1394 (DV)
terminal
DV IN/OUT
terminal
Commercially available DV cable
❍ Do not disconnect the DV cable, or turn off the camcorder or computer while
data is being transferred to the computer.
❍ Operation may not work correctly depending on the software and the
specifications/settings of your computer.
DV NETWORK SOLUTION DISK (Windows XP Users)
Editing
❍ We recommend powering the camcorder from a household power source
while it is connected to the computer.
❍ Refer also to the instruction manual of the computer.
❍ Optional software required. Refer also to the instruction manual of the
software.
❍ ZR70 MC ZR65 MC For transferring recordings from a memory card to the
computer using a USB cable, see p. 129.
Windows XP users can use the software on the supplied DV NETWORK SOLUTION
DISK to perform videoconference and file transfer over the Internet, or upload files
from the computer to the memory card and use the camcorder as card reader/writer.
The available functions depend upon the camcorder model and the networking
environment. For details, refer to the DV NETWORK SOLUTION DISK Software
Instruction Manual.
ZR70 MC ZR65 MC
❍ Do not disconnect the DV cable, remove the memory card or turn off the
camcorder or computer while data is being transferred to the computer (while
the camcorder’s card access indicator is flashing). Doing so may damage the
memory card’s data.
❍ The image files on your memory card and the image files saved on the hard
disk drive of your computer are your valuable, original data files. If you wish to
use image files on your computer, be sure to make copies of them first,
retaining the original.
99
Inserting and Removing the Memory Card
E
The chapter Using a Memory Card (
100-133) refers to functions of the ZR70 MC
and ZR65 MC only.
You can use
SD Memory Cards or a
Terminals
commercially available MultiMediaCards with
this camcorder. The SD Memory Card has a
protect switch for prevent accidental erasure.
❍ This camcorder is compatible with SD Memory Cards or MultiMediaCards only.
Do not use any other types of memory cards.
❍ Turn off the camcorder before inserting or removing the memory card.
Otherwise it may result in data damage.
❍ Do not touch the memory card terminals.
❍ If you use memory cards other than the supplied one, make sure to format
them with the camcorder (
128).
❍ For instructions on how to connect the camcorder to the computer, see
Connecting to a Computer using a USB Cable (
129).
Inserting the Card
1. Turn off the camcorder.
2. Open the cover.
3. Insert the memory card all the way
into the memory card slot.
4. Close the cover.
ZR70 MC ZR65 MC
Using a Memory Card
Do not close the cover forcefully without
having the card correctly inserted.
Removing the Card
Do not forcefully remove the memory card without first pushing it in.
1. Turn off the camcorder.
Make sure that the card access indicator is not
flashing.
2. Open the cover.
3. Push the memory card to release it.
Remove the memory card.
4. Close the cover.
100
Card access
indicator
Selecting the Image Quality/Size
Changing the Still Image Quality
E
You can choose between Superfine, Fine and Normal.
CAMERA
(
44)
PLAY (VCR)
CARD SET UP
CARD CAMERA
CARD PLAY (VCR)
SI QUALITY••FINE
Open the menu and select [CARD SET UP]. Select [SI QUALITY], set it to
[SUPER FINE] or [NORMAL] and close the menu.
Changing the Still Image Size
You can choose between 1024 × 768 pixels and 640 × 480 pixels.
CAMERA
(
44)
PLAY (VCR)
CARD SET UP
CARD CAMERA
CARD PLAY (VCR)
SI SIZE•••••1024×768
Open the menu and select [CARD SET UP]. Select [SI SIZE], set it to [640 ×
480] and close the menu.
❍ Still images recorded in 1024 × 768 pixels may not be displayed correctly in a
camcorder not supporting this size.
❍ Still images are compressed and recorded in the JPEG (Joint Photographic
Experts Group) format.
❍ Depending on subject and recording condition, changing the image quality
may not show a significant difference.
❍ Estimated Capacity of a 8 MB Memory Card and File Size per Image:
640 × 480
No. of Images
File Size
per Image
Superfine
14 images
440 KB
35 images
175 KB
Fine
20 images
300 KB
52 images
120 KB
Normal
39 images
160 KB
86 images
65 KB
Image Quality
These figures are approximate. They vary according to the recording condition
and the subject. Sample images already recorded on the supplied SD Memory
Card are to be included in the total number.
❍ Remaining Image Capacity:
flashing in red: No card
in green: 6 or more images
in yellow: 1 to 5 images
in red: No more images
ZR65 MC
No. of Images
File Size
per Image
ZR70 MC
1024 × 768
Using a Memory Card
Image Size
101
❍ The indication may not decrease even though a recording has been made, or
may decrease by 2 images at once.
❍ All indicators are displayed in green when a memory card is played back.
❍ ZR70 MC The remaining image capacity indicates the number of still images,
even when movies are recorded.
E
ZR70 MC
Changing the Movie Size
You can choose between 320 × 240 pixels and 160 × 120 pixels.
CAMERA
(
44)
PLAY (VCR)
CARD SET UP
CARD CAMERA
CARD PLAY (VCR)
MOVIE SIZE••320×240
Open the menu and select [CARD SET UP]. Select [MOVIE SIZE], set it to
[160 × 120] and close the menu.
❍ Movies are recorded in the Motion JPEG format.
❍ Maximum continuous recording time:
Image Size
Max. Continuous
Recording Time
Total File Size
File Size per Second
320 × 240
10 sec.
2.7 MB
270 KB/sec.
160 × 120
30 sec.
2.7 MB
90 KB/sec.
File Numbers
ZR65 MC
ZR70 MC
Using a Memory Card
Images are automatically assigned file numbers from 0101 to 9900 and stored in
folders containing up to 100 images. Folders are assigned numbers from 101 to 998.
(The sample images on the supplied memory card are saved in the [100canon] folder.)
You can choose to use consecutive file numbers (CONTINUOUS) or to reset the file
number each time a different memory card is inserted (RESET). We recommend setting
the file numbers to CONTINUOUS.
CONTINUOUS
The camcorder memorizes the file number of the last image and assigns the
consecutive file number to the next image, even when a new memory card is inserted.
(If a higher file number already exists on the memory card, the consecutive number
will be assigned.) There will be no duplication of file numbers. This is useful for
organizing images on a computer.
RESET
The file number will be reset each time a new memory card is inserted, starting with
101-0101. If the memory card already contains image files, the consecutive file number
will be assigned.
102
When you record 3 images on the supplied memory card.
101
CONTINUOUS
101-0101
E
RESET
101-0102
101-0103
When you replace the memory
card and record an image.
101
CAMERA
(
44)
101-0104
PLAY (VCR)
CARD SET UP
101
CARD CAMERA
101-0101
CARD PLAY (VCR)
FILE NOS.•••CONTINUOUS
To change the setting, open the menu and select [CARD SET UP]. Select
[FILE NOS.], set it to [RESET] and close the menu.
ZR70 MC ZR65 MC
Using a Memory Card
103
Recording Still Images on a Memory Card
E
You can record still images with the
camcorder, from a tape in the camcorder
(
105), or from devices connected via the
DV terminal or AV terminal (
Card access
indicator
PHOTO button
106).
❍ Do not turn off the camcorder, disconnect the power source or remove the
memory card while the card access display (<<< or >>>) in the upper right
corner of the screen or the card access indicator is flashing. Doing so could
result in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch is
set to allow recording.
Make sure to insert a memory card with enough remaining capacity.
Recording with the Camcorder
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the camcorder to CARD CAMERA mode.
The remaining image capacity and other information appear.
ZR70 MC ZR65 MC
• F flashes in white and turns green when focus is adjusted.
• Exposure is locked.
• When you press the PHOTO button on the wireless controller,
recording starts immediately.
O
OT
PH
Using a Memory Card
2. Press the PHOTO button halfway.
3. Press the PHOTO button fully.
PH
• You hear a shutter sound, and the screen appears as if a
shutter has been released.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
OT
O
To use the self-timer (
70), press the
press the PHOTO button fully.
104
(self-timer) button before step 2 and
Recording from a Tape in the Camcorder
You can record images from a tape in the camcorder as still images on a memory card.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
1. Set the camcorder to PLAY (VCR) mode.
2. Play back the tape.
3. Press the PHOTO button halfway when the scene you wish to record
appears.
• The camcorder pauses playback. The remaining image capacity and other information
appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
4. Press the PHOTO button fully.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
• You can also record a still image by pressing the PHOTO button fully when the tape is
in playback pause mode.
❍ A still image recorded from an image in 16:9 format will be vertically
compressed.
❍ The data code of the still image will reflect the date and time it has been
recorded on the memory card.
❍ There will be no shutter sound in PLAY (VCR) mode.
❍ The image size of a still image recorded from a tape in the camcorder will be
640 x 480.
ZR70 MC ZR65 MC
Using a Memory Card
105
Recording from Other Video Devices
You can record images from devices connected via the S-video terminal or AV terminal
E
(analog line-in function), or via the DV terminal as still images on a memory card.
When recording via the AV terminal, make sure that “AV \ DV” is displayed on
the screen. When recording via the DV terminal, make sure that “AV \ DV” is
not displayed. Change the setting as necessary (
93).
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Connect the camcorder to the video device.
• S-video/AV terminal: See Playing Back on a TV Screen (
41).
• DV terminal: See Connecting a Digital Video Device (
88).
2. Set the camcorder to PLAY (VCR) mode.
If a cassette is loaded, make sure the tape is stopped.
3. Connected device: Load a recorded cassette and play back the tape.
4. Press the PHOTO button halfway when the scene you wish to record
appears.
• The still image, remaining image capacity and other information appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
5. Press the PHOTO button fully.
ZR65 MC
ZR70 MC
Using a Memory Card
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
106
❍ A still image recorded from an image in 16:9 format will be vertically
compressed.
❍ The data code of the still image will reflect the date and time it has been
recorded on the memory card.
❍ There will be no shutter sound in PLAY (VCR) mode.
❍ The image size of a still image recorded from other video devices will be
640 × 480.
Recording Panoramic Images (Stitch Assist Mode)
You can shoot a series of overlapping images and merge them into one large
panoramic scene using the supplied software (PhotoStitch) on a computer.
E
When Recording in Stitch Assist Mode:
PhotoStitch detects the overlapping portion of adjoining images and merges them. Try
to include a distinctive item (landmark, etc.) in the overlapping portion.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the camcorder to CARD CAMERA mode.
2. Press the
button.
MIX/
SLIDE
SHOW
3. Select the direction with the CARD +/– button.
CARD + button: clockwise. CARD – button: anticlockwise.
4. Select the program AE mode and zoom on the subject.
Adjust focus and AE shift manually as necessary. Once the sequence has started, you
cannot change the program AE mode, AE shift, zoom or focus.
O
• Minor discrepancies in the overlapped area can be corrected with the software.
• You can retake an image by pressing the CARD – button to return to the previous
image.
• A maximum of 26 images can be recorded.
7. Press the
ZR65 MC
OT
PH
6. Record the second image so that it overlaps a portion of the first image.
ZR70 MC
Direction and number of recorded images appear.
Using a Memory Card
5. Press the PHOTO button to record the first image.
button after the last image.
For details on how to merge these images, refer to the DIGITAL
VIDEO SOLUTION DISK Software Instruction Manual.
MIX/
SLIDE
SHOW
107
ZR65 MC
ZR70 MC
Using a Memory Card
E
108
❍ Compose each image so that it overlaps 30 to 50% of the adjoining image. Try
to keep the vertical misalignment within 10%.
❍ Do not include moving subject in the overlapping portion.
❍ Do not try to stitch images that include both distant and close subjects. They
may appear warped or doubled up.
ZR70 MC
Recording Motion JPEG Movies on a Memory Card
You can record Motion JPEG movies with the camcorder, from a tape in the camcorder
(
110), or from devices connected via the AV terminal (analog line-in) or the DV
terminal (
110).
E
❍ Do not turn off the camcorder, disconnect the power source or remove the
memory card while the card access display (<<< or >>>) in the upper right
corner of the screen or the card access indicator is flashing. Doing so could
result in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch is
set to allow recording.
❍ Do not load/unload a cassette during recording.
❍ Make sure to insert a memory card with enough remaining capacity.
❍ The sound of a movie recorded on a memory card will be monaural.
Recording with the Camcorder
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the camcorder to CARD CAMERA mode.
2. Press the start/stop button to begin recording.
You can record up to 10 seconds in 320 × 240 and up to 30
seconds in 160 × 120.
CAMERA
OFF
PLAY
(VCR)
3. Press the start/stop button to stop recording.
The camcorder starts writing the movie on the memory card.
70) and
ZR70 MC
(self-timer) button before step 2 (
ZR65 MC
Using a Memory Card
To use the self-timer, press the
press the start/stop button.
109
Recording from a Tape in the Camcorder
You can record movies from a tape in the camcorder on a memory card.
E
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the camcorder to PLAY (VCR) mode.
2. Play back the tape.
3. Press the start/stop button when the scene you wish to record appears.
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.
4. Press the start/stop to stop recording.
❍ A movie recorded from an image in 16:9 format will be vertically compressed.
❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
Recording from Other Video Devices
You can record movies from devices connected via the S-video terminal or AV terminal
(analog line-in function), or via the DV terminal on a memory card.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Connect the camcorder to the video device.
• S-video/AV terminal: See Playing Back on a TV Screen (
41).
• DV terminal: See Connecting a Digital Video Device (
88).
2. Set the camcorder to PLAY (VCR) mode.
If a cassette is loaded, make sure the tape is stopped.
3. Connected device: Load a recorded cassette and play back the tape.
ZR65 MC
ZR70 MC
Using a Memory Card
4. Press the start/stop button when the scene you wish to record appears.
110
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.
5. Press the start/stop button to stop recording.
❍ A movie recorded from an image in 16:9 format will be vertically compressed.
❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
Playing Back a Memory Card
You can play back memory card images on the LCD screen, viewfinder screen, or on a
connected TV screen (see Playing Back on a TV Screen (
You can display a single image (single image display
screen
112), or one after another (slide show
41) ).
E
111), 6 at one time (index
112). Use the Card Jump function
to quickly locate an image without displaying them one by one (
113).
❍ Images not recorded with this camcorder, uploaded from a computer (except
the sample images
132), edited on a computer and images whose file
names have been changed may not be played back correctly.
❍ Still images not recorded with this camcorder may not be printed correctly on a
Bubble Jet Printer with direct print function.
❍ Do not turn off the camcorder, disconnect the power source or remove the
memory card while the card access display (<<<) in the upper right corner of
the screen or the card access indicator is flashing. Doing so could result in data
damage.
❍ Make sure to insert a memory card that contains images.
❍ Only date and time will be displayed when pressing the DATA CODE button.
❍ You can enlarge still images by 2 times during playback (
82).
Single Image Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the camcorder to CARD PLAY (VCR) mode.
3. ZR70 MC To play back a movie, press the e/a button.
The last scene appears as a still image when playback is
complete.
ZR65 MC
Press the CARD + button to display the next image and the
CARD – button to display the previous image.
ZR70 MC
2. Press the CARD+/– button to move between images.
Using a Memory Card
• The last recorded image appears.
• ZR70 MC Movies are displayed with the first scene as a still image indicated by
“e/a”.
FOCUS
111
Index Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
1. In single image display, press the
button.
(index screen)
AE SHIFT
• Up to 6 images appear.
• ZR70 MC Movies are displayed with the first scene as a still
image indicated by “
”.
2. Press the CARD +/– button to change the image
selection.
3. Move the
mark to the image you wish to view.
• Turn the selector dial up to move to the next image and down
to move to the previous image.
• Turning the selector dial up on the last image displays the next
index screen. Turning the selector dial down on the first image
displays the previous index screen.
4. Press the
(index screen) button.
The index screen is canceled and the selected image appears in
single image display.
AE SHIFT
Slide Show
ZR65 MC
ZR70 MC
Using a Memory Card
CAMERA
112
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. In single image display, press the SLIDE SHOW
button.
Images are played back one after another.
2. Press the SLIDE SHOW button to stop the slide show.
MIX/
SLIDE
SHOW
Card Jump Function
You can locate still images/movies without displaying them one by one. The number in
the upper right of the screen indicates the image number of the current image by the
total number of images.
CAMERA
PLAY (VCR)
CARD CAMERA
E
CARD PLAY (VCR)
In single image display, press and hold the CARD + or
CARD – button.
• Press the CARD + button to jump forward and the CARD – button
to jump backward.
• When you release the button, the still image/movie of the
displayed image number appears.
ZR70 MC ZR65 MC
Using a Memory Card
113
Protecting Images
E
You can protect important images from accidental erasure during single image display
or index screen display.
If a memory card is formatted, all images, even protected ones, will be erased
permanently.
❍ The sample images recorded on the supplied SD Memory Card are already
protected.
❍ ZR70 MC Movies can only be protected when the first or last scene is displayed
as a still image. They cannot be protected during playback pause.
❍ Make sure to insert a memory card that contains images.
Protecting during Single Image Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Select the image you wish to protect.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [PROTECT
].
•“
” appears and now the image cannot be erased.
• To cancel the protection, press the selector dial.
4. Select [b RETURN] to close the menu.
Protecting during Index Screen Display
ZR70 MC ZR65 MC
Using a Memory Card
CAMERA
(
44)
PLAY (VCR)
CARD OPERATIONS
CARD CAMERA
CARD PLAY (VCR)
PROTECT
1. In single image display, press the
(index screen) button.
Up to 6 images appear.
2. Open the menu and select [CARD OPERATIONS].
3. Select [\ PROTECT
].
4. Select the image you wish to protect and press the selector dial.
•“
” appears on the image.
• Repeat this step to protect more images.
• To cancel the protection, press the selector dial.
5. Press the MENU button.
To cancel the protection, press the selector dial in step 4. “
the image can now be erased.
114
” disappears and
Erasing Images
You can erase images singly or all at once.
E
Be careful when erasing images. Erased images cannot be recovered.
❍ Protected images cannot be erased.
❍ ZR70 MC Movies can only be erased when the first or last scene is displayed as
a still image. They cannot be erased in playback pause mode.
❍ Make sure to insert a memory card that contains images.
Erasing a Single Image
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Select the image you wish to erase.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [IMAGE ERASE].
• “ERASE THIS IMAGE?”, [NO] and [YES] appears.
• If an image is protected, [YES] appears in purple.
4. Select [YES].
The image is erased and the previous image appears.
5. Select [b RETURN] to close the menu.
Erasing a Single Image/All Images
CAMERA
CARD OPERATIONS
CARD PLAY (VCR)
IMAGE ERASE
2. Select [IMAGE ERASE].
3. Select [SINGLE] or [ALL].
• When erasing a single image: “ERASE THIS IMAGE?” [NO] and
[YES] appears. If an image is protected, [YES] appears in purple.
• When erasing all images: “ERASE ALL IMAGES? [EXCEPT FOR
and [YES] appears.
ZR65 MC
1. Open the menu and select [CARD OPERATIONS].
ZR70 MC
44)
CARD CAMERA
Using a Memory Card
(
PLAY (VCR)
IMAGES]”, [NO]
4. Select [YES] and close the menu.
• When erasing a single image: The image is erased and the previous image appears. To
erase another image, select the image with the CARD +/– button and select [YES].
• When erasing all images: All images with exception of the protected images are erased.
115
Selecting Still Images for Printing (Print Order)
E
You can select still images for printing and set the number of copies. These print order
settings are compatible with the Digital Print Order Format (DPOF) standards.
❍ Make sure to insert a memory card that contains images.
❍ A maximum of 200 still images can be selected.
❍ ZR70 MC Movies cannot be printed.
Selecting in Single Image Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Select the still image you wish to print.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [
PRINT ORDER].
4. Select the number of copies.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
5. Select [b RETURN] to close the menu.
Selecting in Index Screen Display
CAMERA
(
44)
PLAY (VCR)
CARD OPERATIONS
ZR70 MC ZR65 MC
Using a Memory Card
1. In single image display, press the
116
CARD CAMERA
CARD PLAY (VCR)
PRINT ORDER
(index screen) button.
Up to 6 images appear.
2. Open the menu and select [CARD OPERATIONS].
3. Select [\
PRINT ORDER].
4. Select the still image you wish to print and press the selector dial.
5. Set the number of copies with the selector dial and close the menu.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
• Repeat steps 4 and 5 to continue the print order setting.
Erasing All Print Orders
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
(
CARD OPERATIONS
44)
PRINT ORDERS ALL ERASE
1. In single image display, open the menu and select [CARD OPERATIONS].
2. Select [
PRINT ORDERS ALL ERASE].
“ERASE ALL
PRINT ORDERS?”, [NO] and [YES] appears.
3. Select [YES].
All “
” disappear.
4. Select [b RETURN] to close the menu.
ZR70 MC ZR65 MC
Using a Memory Card
117
Printing with the Direct Print Function
E
You can print still images by connecting the camcorder to a Canon Bubble Jet Printer
with Direct Print function. The Direct Print function can also be used with the print
order settings (
116).
❍ Observe the following precautions during printing, otherwise printing may not
be performed correctly.
- Do not turn off the camcorder or the printer.
- Do not change the position of the TAPE/CARD switch.
- Do not detach the cable.
- Do not remove the memory card.
❍ Canon Bubble Jet Printers with Direct Print function (as of January 2003):
S830D, S820D, S530D.
❍ We recommend powering the camcorder from a household power source.
❍ Refer also to the instruction manual of the respective printer.
Connecting the Printer to the Camcorder
POWER
CAMERA
TAPE
CARD
ZR70 MC ZR65 MC
Using a Memory Card
OFF
PLAY
(VCR)
Canon Bubble Jet Printer with direct
print function
1. Turn off the camcorder and insert a memory card that contains images.
2. Connect a power source to the printer and turn on the printer.
3. Set the camcorder to CARD PLAY (VCR) mode.
Wait until the card access indicator stops flashing.
4. Connect the camcorder to the printer using the cable.
Print SET appears when the printer is properly connected to the camcorder. (Does not
appear with movies, or still images that cannot be played back with the camcorder.)
118
Printing
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
1. In single image display, select the still image you
wish to print and press the selector dial.
The print setting menu appears.
2. Set the number of copies and the print style.
• Selecting the Number of Copies.
• Setting the Print Style.
3. Select [Print] and press the selector dial.
Printing starts. The print setting menu disappears when printing
is complete.
If an error message appears, see Printing Errors (
Messages (
140).
121) and Direct Print Related
Selecting the Number of Copies
A maximum of 9 copies can be selected for one still image.
1. In the print setting menu, turn the selector dial so
that
appears next to [Copies] and press the
selector dial.
Paper Size
Card #1*, Card #2*, Card #3*, LTR, A4
For details on paper type, refer to the Bubble Jet Printer User
Guide.
Borders
Borderless
Prints right to the edges of the page
Bordered
Prints with a border
ZR70 MC ZR65 MC
Setting the Print Style
Using a Memory Card
2. Turn the selector dial to select the number of copies and press the
selector dial.
* Recommended paper size
119
Selecting the paper size:
E
1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
2. Make sure that
dial.
is selected and press the selector
3. Turn the selector dial to select the paper size and press the selector dial.
4. Press the MENU button.
You return to the print setting menu.
Selecting the Borders:
1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
ZR65 MC
ZR70 MC
Using a Memory Card
2. Select
120
and press the selector dial.
3. Select a setting option and press the selector dial.
4. Press the MENU button.
You return to the print setting menu.
❍ Bordered: The image area remains relatively unchanged from the recorded
image when it is printed.
❍ Borderless: The center portion of the recorded image is printed at an enlarged
size. The image’s top, bottom and sides may be cropped slightly.
Printing with Print Order Settings
You can print still images you have selected with the Print Order function. If you wish
to print more than 1 copy, set the number of copies in the print order (
CAMERA
(
44)
PLAY (VCR)
CARD CAMERA
116).
E
CARD PLAY (VCR)
PRINT
1. Connect the printer to the camcorder (
118).
2. Press the MENU button.
3. Select [\
PRINT].
• The print setting menu appears.
• “Set print order” appears, when you connect a printer with direct print function and
select \ PRINT without having set the print order.
• The total number of prints set in the print order is displayed on the upper left of the
screen.
4. Set the print style.
Setting the Print Style (
119).
5. In the print setting menu, select [OK] and press the selector dial.
Printing starts. The print setting menu disappears when printing is complete.
ZR70 MC ZR65 MC
Using a Memory Card
❍ Cancel Printing
Press the selector dial while “Now Printing” is displayed. A confirmation dialog
appears. Select [OK] and press the selector dial. Printing stops even if it is
incomplete and the paper is fed through.
❍ Restarting Printing (with
print order only)
Open the CARD PLAY (VCR) menu and select [\
PRINT]. Select [Restart] in
the print setting menu and press the selector dial. The remaining images will
be printed.
Printing cannot be restarted in the following cases:
- When you change the print order settings.
- When you delete a still image with print order settings.
❍ Printing Errors
If an error occurs during the printing process, an error message appears
(
140). With most errors, printing resumes automatically after you correct
the error. If the error persists, press the selector dial to cancel printing.
❍ Follow below procedure when disconnecting the interface cable:
1. Disconnect the cable from the camcorder and printer.
2. Turn off the camcorder.
121
Combining Images (Card Mix)
E
You can produce effects not possible with just a tape with the Card Mix function.
Choose one of the sample images provided on the supplied SD Memory Card (such as
picture frames, backgrounds and animations) and combine it with the live video
recording.
❍ Card Mix cannot be used in the Night and Super Night (ZR70 MC) mode.
❍ ZR70 MC Movies recorded on a memory card cannot be combined with
camcorder recordings.
❍ Make sure to load a cassette and to insert a memory card that contains card
mix images.
❍ Additional sample images are provided on the supplied DIGITAL VIDEO
SOLUTION DISK. For instructions on how to upload them to the memory card,
refer to Adding Still Images from Your Computer to the Memory Card in the
DIGITAL VIDEO SOLUTION DISK Software Instruction Manual.
❍ Reselect the card mix image when you have turned off the camcorder or
changed the position of the program selector.
Card Mix Effects
You can select from the following 4 types of Card Mix effects:
Card Chroma Key (CARD CHROMA)
Combines frames with your recordings. The live video recording will appear in place of
the blue area of the card mix image. If you create your own frame, make sure that the
area the live recording should appear is blue.
Mix level adjustment: blue area of the still image.
ZR70 MC ZR65 MC
Using a Memory Card
Live video recording
122
Card mix image
Card Luminance Key (CARD LUMI.)
Combines illustrations or title with your recordings. The live video recording will
appear in place of the light area of the card mix image. You can create your own title
or illustration by drawing on a white paper and recording it to the memory card.
Mix level adjustment: light area of the still image.
Live video recording
E
Card mix image
Camera Chroma Key (CAM. CHROMA)
Combines backgrounds with your recordings. Record your subject in front of a blue
curtain, and the subject not blue will be superimposed on the card mix image.
Mix level adjustment: blue area of the live video recording.
Live video recording
Card mix image
Card Animation (C. ANIMATION)
Card mix image
ZR70 MC ZR65 MC
Live video recording
Using a Memory Card
Combines animations with your recordings. You can choose from 3 types of card
animation effects.
Corner: Animation appears on the upper left and the lower right corner of the screen.
Straight: Animation appears on the top and bottom of the screen and moves to the
right and left.
Random: Animation moves randomly in the display.
Mix level adjustment: blue area of the card animation image.
123
Selecting the Card Mix Effect
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
(
44)
CARD MIX
MIX TYPE•••CARD CHROMA
MIX LEVEL••–
+
1. Set the program selector to Q.
2. Open the menu and select [\ CARD MIX].
The card mix menu appears.
3. Select the image you wish to combine with the
CARD +/– button.
4. Select [MIX TYPE].
[CARD CHROMA], [CARD LUMI.], [CAM. CHROMA] and [C. ANIMATION] appears.
5. Select the mix type matching the image you have selected (
132).
• The screen shows the combined image.
• When you have selected [C. ANIMATION], select [ANIMAT. TYPE] and select between
[CORNER], [STRAIGHT] and [RANDOM].
6. To adjust the mix level, select [MIX LEVEL] and adjust it with the
selector dial.
7. Close the menu.
MENU
ZR65 MC
ZR70 MC
Using a Memory Card
“CARD MIX” flashes.
124
Activating the Card Mix Effect
1. Press the CARD MIX button.
• “CARD MIX” stops flashing.
• The combined image appears.
• You can activate and deactivate the card mix effect by pressing
the CARD MIX button.
MIX/
SLIDE
SHOW
Recording with the Card Mix Effect
Movie:
1. Press the start/stop button to begin recording.
E
The combined image is recorded on the tape.
CAMERA
OFF
PLAY
(VCR)
2. Press the start/stop button to end recording.
Still Image:
1. Press the PHOTO button halfway.
F flashes in white and turns green when focus is adjusted.
PH
O
OT
2. Press the PHOTO button fully.
PH
O
OT
• The camcorder records the still image on the tape for approx. 6
seconds. During this time, the camcorder displays the still
image and keeps recording the sound.
• The camcorder returns to record pause mode.
ZR70 MC ZR65 MC
Using a Memory Card
125
Copying Still Images
E
You can copy still images from tape to memory card, or from memory card to tape.
❍ All still images from the selected still image onward will be copied.
❍ The image size of a still image copied from tape to memory card will be 640 ×
480.
❍ The data code of the still image reflects the date and time it has been copied.
Copying Still Images from Tape to Memory Card
Insert a memory card with enough remaining capacity, and load a recorded cassette.
CAMERA
(
44)
CARD CAMERA
PLAY (VCR)
CARD OPERATIONS
COPY[
CARD PLAY (VCR)
]
1. Locate the still image you wish to copy on the tape
and stop the tape shortly before the still image.
• You can also use the photo search function to easily locate the
still image.
• To copy all still images from the tape, rewind the tape to the beginning.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [b \
] ].
[CANCEL] and [EXECUTE] appears.
ZR70 MC ZR65 MC
Using a Memory Card
4. Select [EXECUTE].
126
• “NOW COPYING” appears.
• The still image being copied is shown on the screen.
• Copying stops when the tape reaches the end or the memory card is full (“CARD
FULL” appears).
5. Press the 3 (stop) button to end copying.
AE SHIFT
Copying Still Images from Memory Card to Tape
Load a cassette with enough free space, and insert a recorded memory card. Make
sure that the protect tab on the cassette is set to allow recording.
CAMERA
(
44)
PLAY (VCR)
CARD OPERATIONS
CARD CAMERA
COPY[
E
CARD PLAY (VCR)
]
1. Select the first still image you wish to copy with the
CARD +/– buttons.
To copy all still images from the memory card, select the first still
image.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [
\ b] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• It takes about 6 seconds per still image to be copied to the tape.
• Copying stops when all still images are copied or the tape is full.
5. Press the 3 (stop) button to end copying.
AE SHIFT
ZR70 MC ZR65 MC
Using a Memory Card
127
Formatting a Memory Card
E
Format new memory cards, or when you get the message “CARD ERROR”. You can
also format a memory card to erase all images recorded on it.
The camcorder formats memory cards in the Design rule for Camera File system (DCF)
standard.
❍ Formatting a memory card erases all data, including protected images.
❍ Images erased by formatting cannot be recovered.
❍ If you use a memory card other than the supplied one, format it with the
camcorder.
❍ Makes sure to insert the memory card you wish to format into the camcorder.
CAMERA
(
44)
PLAY (VCR)
CARD OPERATIONS
CARD CAMERA
FORMAT
1. Open the menu and select [CARD OPERATIONS].
2. Select [FORMAT].
[CANCEL] and [EXECUTE] appears.
3. Select [EXECUTE].
[FORMAT THIS CARD?], [NO] and [YES] appears.
4. Select [YES] and close the menu.
ZR70 MC ZR65 MC
Using a Memory Card
• Formatting starts.
• Selecting [NO] brings you back to step 3.
128
CARD PLAY (VCR)
Connecting to a Computer Using a USB Cable
You can download images from the memory card to a computer using the supplied
USB cable. With the supplied software, you can easily download, browse and archive
images, and arrange still images for printout.
E
For instructions on how to connect the camcorder to the computer, and
install and operate the software, refer to the DIGITAL VIDEO SOLUTION
DISK Software Instruction Manual.
• Refer also to the computer instruction manual.
• “PC CONNECT
” appears to indicate that the camcorder is
connected to the computer via USB cable.
PC CONNECT
ZR70 MC
ZR65 MC
❍ We recommend powering the camcorder from a household power source
while it is connected to the computer.
❍ ZR70 MC The light-up buttons turn off during USB connection.
❍ For transferring recordings from to a computer using a DV cable, see p. 99.
❍ Still images/movies recorded on a tape cannot be transferred to a computer via
USB interface.
Using a Memory Card
❍ Do not disconnect the USB cable, remove the memory card, change the
position of the POWER switch or turn off the camcorder and computer while
data is being transferred to the computer (while the camcorder’s card access
indicator is flashing). Doing so may damage the memory card’s data.
❍ Operation may not work correctly depending on the software and the
specifications/settings of your computer.
❍ The image file on your memory card and the image files saved on the hard disk
drive of your computer are valuable, original data files. If you wish to use
image files on your computer, make copies of them first, and use the copied
file, retaining the original.
129
Creating a Start-up Image
E
You can create a start-up image using a still image on the memory card or a sample
start-up image provided on the DIGITAL VIDEO SOLUTION DISK and save it as [MY
IMAGE].
❍ Make sure to insert a memory card with enough remaining capacity.
❍ Before you create a start-up image, you need to record a still image on the
memory card.
❍ Retain the original data of the still image you have set as the start-up image on
your computer or removable disk.
Preparations
Record a still image on the memory card.
OR
Upload a still image from your computer to the memory card using the
software in the DIGITAL VIDEO SOLUTION DISK.
For instruction on how to upload a still image to the memory card, refer to Adding Still
Images from Your Computer to the Memory Card in the DIGITAL VIDEO SOLUTION DISK
Software Instruction Manual.
Setting the Still Image as Start-up Image
CAMERA
(
44)
PLAY (VCR)
MY CAMERA
CARD CAMERA
CARD PLAY (VCR)
CREATE START–UP IMAGE
1. Open the menu.
ZR70 MC ZR65 MC
Using a Memory Card
2. Select [MY CAMERA].
130
3. Select [CREATE START-UP IMAGE].
[SET THIS AS START-UP IMAGE?], [YES] and [NO] appears.
4. Select a still image with the CARD +/– buttons and select [YES].
[OVERWRITE MY IMAGE?], [YES] and [NO] appears.
5. Select [YES].
The still image will be saved, and the image that was saved to [MY IMAGE] is erased.
Memory Card Information
Images recorded on a memory card with this camcorder can be transferred to a
computer using the following products for SD Memory Cards or MultiMediaCards:
PC Card Adapter:
E
An adapter to insert a memory card into the card slot on the
computer.
USB Reader/Writer: Connects to the USB port of a computer for direct access to the
memory card.
FD Adapter:
An adapter to insert a memory card into the floppy disk drive on
the computer.
Memory Cards that are confirmed to operate with this camcorder
(as of January 2003):
SD Memory Card: Panasonic: 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB
SanDisk: 16 MB, 32 MB, 64 MB
MultiMediaCard: SanDisk: 16 MB, 32 MB, 64 MB
However, we cannot guarantee that all of these memory cards work properly.
Memory Card Handling Precautions
ZR70 MC
ZR65 MC
Using a Memory Card
❍ Format new memory cards with the camcorder. Memory cards formatted with
other devices such as a computer may not operate correctly.
❍ We recommend saving backups of memory card images on your computer’s hard
drive or other external memory device. Image data may be corrupted or lost due to
memory card defects or exposure to static electricity. Canon Inc. makes no
warranties for corrupted or lost data.
❍ Do not turn off the camcorder, disconnect the power source or remove the memory
card while the card access indicator is flashing.
❍ Do not use memory cards in places subject to strong magnetic fields.
❍ Do not leave memory cards in places subject to high humidity and high
temperature.
❍ Do not disassemble memory cards.
❍ Do not bend, drop, or subject memory cards to shocks and do not expose them to
water.
❍ Moving a memory card rapidly between hot and cold temperatures may cause
condensation to form on its external and internal surfaces. If condensation forms
on the card, put it aside until the droplets have evaporated completely.
❍ Do not touch or expose the terminals to dust or dirt.
❍ Store and carry memory cards in the supplied case to protect the terminals.
❍ Check the direction before inserting the memory card. Forcing a memory card
backwards into the slot may damage the memory card or the camcorder.
❍ Do not remove the label from the memory card, or affix other labels on the
memory card. If you wish to add labels, affix them to the case.
131
Sample Images
27 sample images are pre-recorded on the supplied SD Memory Card: 8 card chroma
E
key images, 5 card luminance key images, 2 camera chroma key images and 12 card
animation images.
Card Chroma Key
Card Luminance Key
Camera Chroma Key
ZR65 MC
ZR70 MC
Using a Memory Card
Card Animation
132
The sample images recorded on the supplied SD Memory Card are intended only
for the personal use with this camcorder. Do not use these sample images for
other purposes.
If you have mistakenly erased the Card Mix sample images on the supplied SD
Memory Card, they can be downloaded from the homepage
http://www.canondv.com.
For details on how to add the downloaded images to the memory card, refer to
Adding Still Images from Your Computer to the Memory Card in the DIGITAL
VIDEO SOLUTION DISK Software Instruction Manual.
If you cannot use the USB cable to connect the camcorder to a computer, you will
need a PC Card Adapter to upload the images to a memory card.
E
PhotoEssentials – Royalty Free Stock Photography
The PhotoEssentials suite of royalty-free images on CD-ROM features premium quality assignment
photography and is ideally suited for use in advertising, brochures, reports, multimedia, websites,
books, packaging and more.
For more information, please visit their website www.photoessentials.com
ZR70 MC ZR65 MC
Using a Memory Card
133
Screen Displays
E
LCD Screen Displays
You can hide the displays on the LCD screen to have a clear screen for playback.
CAMERA
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
CARD PLAY (VCR)
DISPLAYS••••ON
Open the menu and select [DISPLAY SET UP]. Select [DISPLAYS], set it to
[OFF <PLAYBK>] and close the menu.
• The LCD screen will become completely blank (also the TV screen if connected).
• Warning messages still appear, and the data code appears if turned on.
• Tape operation displays appear for 2 seconds.
• ZR70 MC ZR65 MC Displays cannot be hidden on the index screen.
TV Screen Displays
When you connect a TV for recording/playback, you can hide the displays on the TV
screen. For connecting instructions, see Playing Back on a TV Screen (
41).
CAMERA
PLAY (VCR)
CARD CAMERA
Press the TV SCREEN button on the wireless controller.
CARD PLAY (VCR)
SELF T. D.EFFECT.
MENU
• When the POWER switch is set to CAMERA: The displays
disappear from the TV screen and appear when you press the
button again.
• When the POWER switch is set to PLAY (VCR): The displays appear on the connected TV
screen and disappear when you press the button again. The setting resets to the OFF
setting when you turn the camcorder off.
When the TV screen displays are hidden, the displays still appear on the LCD screen. If
you turn on the data code, displays other than the data code will disappear from the LCD
screen.
TV SCREEN ON/OFF
INDEX SLIDE SHOW
SET
CARD
Additional
Information
DATA CODE SEARCH SELECT
You can also change the setting in the menu during recording:
CAMERA
(
44)
PLAY (VCR)
DISPLAY SET UP
CARD CAMERA
CARD PLAY (VCR)
TV SCREEN•••ON
Open the menu and select [DISPLAY SET UP]. Select [TV SCREEN], set it to
[OFF] and close the menu.
134
Screen Displays during Basic Recording/Playback
indicates flashing.
SP PAUSE
0:00:00
5min
CAMERA mode (battery pack attached):
• Remote sensor mode and audio mode disappear after 4
E
1
seconds.
12bit
PLAY (VCR) mode:
• Remote sensor mode and volume bar disappear after 4
seconds.
STEREO1
SP STOP
0:00:00:00
5min
1
–
REC
PAUSE
STOP
EJECT
/
2
/
1
/
FF
REW
/
/
/
/
RTN
: Fast forward playback/
/ RTN
: Zero set memory (forward
rewind playback ( 38)
and
reverse) ( 86)
2 : ×2 playback
/ : AV insert editing ( 94)
(forward and reverse) ( 38)
1 : ×1 playback
/ : Audio dubbing ( 96)
(forward and reverse) ( 38)
: Slow playback
(forward and reverse) ( 38)
: Frame advance playback/
frame reverse playback ( 38)
: Playback pause
(forward and reverse) ( 38)
: Date search/photo search ( 85)
STEREO1
PAUSE
1:23:45:00
END
1
16bit
Time code ( 86)
Remaining tape
Remaining battery charge (
Remote sensor mode (
Audio mode (
71)
49)
18)
Additional
Information
: Backup
battery ( 19)
: Condensation
warning ( 143)
+
135
Screen Displays during Advanced Recording/Playback
CAMERA Mode
E
* ZR70 MC
Image stabilizer (
Zoom (
Recording reminder/
Self-timer countdown (
Photo recording timer (
69)
30)
AE shift ( 77)
Program AE ( 57)
Manual focus ( 75)
Shutter speed ( 78)
White balance ( 80)
Card mix ( 122)
Digital effects ( 61)
Date and time ( 83)
70)/
55)
Recording mode
( 54)
W
Self-timer ( 70)
Headphones ( 39)
Wind screen ( 71)
Audio mode ( 71)
SP
T
AE 0
MF
1/100
1sec
–
CARD MIX
FADE–T
12:00 PM
JAN.1,2003
+
WSON
12bit
16:9
PHOTO
16:9 mode ( 52)
Photo mode ( 55)
Accessory attached to
the Advanced Accessory
shoe* ( 73)
AF/AE locked in
Photo mode ( 55)
PLAY (VCR) Mode
12bit audio out (
98)
MIX/VARI.
Photo search/
Date search ( 85)
1
1
1
Photo search/
Date search ( 85)/
AV insert ( 94)/
Audio dubbing ( 96)
Additional
Information
Data code (
136
83)
PHOTO SEARCH
F1.8
1/1000
12:00 PM
JAN.1,2003
–
10
10
12bit
Volume level of built-in
speaker or headphones
( 40)
DV IN
Audio mode (
+
DV input (
90)
71)
ZR70 MC ZR65 MC
CARD CAMERA Mode
* ZR70 MC
Stitch assist (
Zoom (
Recording on a memory
card ( 104)
107)
Still image quality (
30)
Program AE (
W
Print order (
101)
Remaining card capacity
( 101)
57)
AE shift ( 77)
Manual focus
( 75)
Shutter speed
( 78)
White balance
( 80)
Date and time ( 83)
AF/AE locked in
Photo mode ( 104)
ZR70 MC ZR65 MC
E
T
AE 0
MF
1/100
1 2
12:00 PM
JAN.1,2003
S.FINE
50
1024
320
Still image size
( 101)
Movie size* ( 102)
Self-timer (
CLOSE
Stitch assist (
70)
107)
Accessory attached to
the Advanced Accessory
shoe* ( 73)
CARD PLAY (VCR) Mode
116)
Protect mark (
114)
Folder numberFile number ( 102)
Slide show (
112)
Accessing
a memory card (
SLIDE SHOW
101–0143
43/50
640 480
Current still image/
Total still images
111)
12:00 PM
JAN.1,2003
Data code (
83)
Additional
Information
137
List of Messages
Additional
Information
E
138
Message
SET THE TIME ZONE,
DATE AND TIME
Explanation
You have not set the time zone, date and time. This message
appears each time you turn the power on until you set the
time zone, date and time.
CHANGE THE
Battery pack is exhausted. Replace or charge the battery
BATTERY PACK
pack.
Cassette is protected. Replace the cassette or change the
THE TAPE IS SET FOR
ERASURE PREVENTION position of the protect switch.
REMOVE THE
Camcorder stopped operating to protect the tape. Unload
CASSETTE
and reload the cassette.
CHECK THE DV INPUT DV cable is not connected, or the connected digital device is
turned off.
CONDENSATION HAS Condensation has been detected in the camcorder.
BEEN DETECTED
Tape reached the end. Rewind the tape or replace the
TAPE END
cassette.
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a
[REC MODE]
tape recorded in a mode other than the SP mode.
CHECK THE CASSETTE You attempted to perform audio dubbing on a tape
recorded in 16-bit or 12-bit 4-channel sound.
[AUDIO MODE]
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a
tape with a blank section.
[BLANK]
COPYRIGHT PROTECTED You attempted to play back a copyright protected tape.
PLAYBACK IS RESTRICTED
You attempted to dub a copyright protected tape. May also
COPYRIGHT
PROTECTED DUBBING appear when an anomalous signal is received during analog
line-in recording, or during analog-digital conversion of a
RESTRICTED
copyright protected tape.
25
16
23
22
90
143
22
54
96
94
91
91
ZR70 MC ZR65 MC
Memory Card Related Messages
Message
NO CARD
THE TAPE IS SET FOR
ERASURE PREVENTION
NO IMAGES
CARD ERROR
Explanation
Memory card not is inserted into the camcorder.
SD Memory Card is set for erasure prevention. Replace the
card or change the position of the protect switch.
No images are recorded on the memory card.
A memory card error occurred. The camcorder cannot record
or play back the image.
The error may be temporary. If the message disappears after
4 seconds and flashes red, turn the camcorder off, remove
the card and reinsert the card. If
changes to green, you
can continue recording/playback.
No remaining capacity on the memory card. Replace with
CARD FULL
another card or erase images.
File or folder number has reached the maximum value.
NAMING ERROR
Image is recorded in a not compatible JPEG format or
UNIDENTIFIABLE
another format not compatible with the camcorder, or the
IMAGE
image file is corrupted.
PRINT ORDER ERROR You attempted to set more than 200 still images in the print
order.
THIS IMAGE CANNOT Some analog images cannot be recorded on the memory
card depending on the signal.
BE RECORDED
100
100
E
111
100
115
102
111
116
106
Additional
Information
139
ZR70 MC ZR65 MC
E
Direct Print Related Messages
Message
No Paper
Paper Jam
No Ink
Communication Error
Could not print X
images
Cannot Print!
Set print order
Printer in use
Printer warming up
No printhead
Printer cover open
Media type error
Paper lever error
Low ink level
Waste tank full
Additional
Information
Printer error
140
Explanation
Paper cassette is not correctly inserted or is out of paper.
The paper jammed during printing.
The ink cartridge is not inserted or is out of ink.
The printer is experiencing a data transmission error.
You attempted to use the print order settings to print X images
that were made with another camcorder, have a different format
or were edited on a computer.
You attempted to print an image that was made with another
camcorder, has a different format, or was edited on a computer.
You attempted to print an image from the Card Play menu
[\ PRINT] without having set the print order.
The printer is printing from a computer or a memory card inserted
into the printer. It automatically starts printing from the
camcorder when current prints are complete.
Printer is warming up. The printer automatically starts printing
when it is ready.
No print head is installed in the printer.
Printer cover is open. Close the printer cover securely.
Wrong paper. Cancel printing and set the paper you chose in the
print settings menu.
Paper lever error occurred. Adjust the paper selection lever to the
proper position.
The ink tank needs to be replaced soon. Prepare a new ink tank. If
you select [Continue] in the error screen, you can restart printing.
Waste tank is full. You can restart printing by pressing the
RESUME/CANCEL button on the Bubble Jet Printer. Request
replacement of the waste tank at the shop where you purchased
the printer or the nearest Canon customer support center listed in
the Bubble Jet Quick Start Guide.
Turn off the printer and turn it back on. If the error persists,
consult the nearest Canon customer support center listed in the
Bubble Jet Quick Start Guide.
Maintenance
Camcorder Handling Precautions
❍ Do not carry the camcorder by the LCD panel or viewfinder.
E
❍ Do not leave the camcorder in places subject to high temperatures, such as a sunheated car, and high humidity.
❍ Do not use the camcorder in places subject to magnetic or electric fields such as
near the TV transmitters or portable communication devices.
❍ Do not point the lens or viewfinder at strong light sources. Do not leave the
camcorder pointed at a bright subject.
❍ Do not use the camcorder in dusty or sandy places. Dust or sand getting inside the
cassette or camcorder may cause damage. Dust and sand can also damage the lens.
Attach the lens cap after use.
❍ The camcorder is not waterproof. Water, mud or salt getting inside the cassette or
camcorder may cause damage.
❍ Be careful of heat generated by lighting equipment.
❍ Do not disassemble the camcorder. If the camcorder does not function properly,
consult qualified service personnel.
❍ Handle the camcorder with care. Do not subject the camcorder to shocks or
vibration as this may cause damage.
❍ Avoid sudden changes in temperature. Moving the camcorder rapidly between hot
and cold temperatures may cause condensation to form on its internal surfaces.
(
143)
Storage
❍ If you do not intend to use the camcorder for a long time, store it in a place free of
dust, in low humidity, and at temperatures not higher than 86˚F (30˚C).
❍ After storage, check the functions of your camcorder to make sure that the
camcorder is still working properly.
Cleaning
❍ Use a soft, dry cloth to clean the camcorder body and lens. Never use chemically
treated cloth or volatile solvents such as paint thinner.
Additional
Information
Camcorder Body and Lens
LCD Screen
❍ Clean the LCD screen using a commercially available cleaning cloth for glasses.
❍ Condensation may form on the surface of the screen when the temperature
changes suddenly. Wipe it with a soft dry cloth.
141
❍ At cold temperatures, the screen may be darker than usual. This is not a
malfunction. The screen returns to normal when the camcorder warms up.
E
Viewfinder
❍ Rotate the viewfinder upward. Remove the protect cover
and clean the glass with a cotton swab. Reattach the
protect cover when finished.
❍ Be careful not to scratch the glass when cleaning.
Video Heads
Additional
Information
❍ When the playback picture becomes distorted, the video heads need to be cleaned.
❍ To maintain the best picture quality, we recommend cleaning the video heads
frequently with the Canon DVM-CL Digital Video Head Cleaning Cassette or a
commercially available dry cleaning cassette.
❍ Do not use wet type cleaning cassettes as this may damage the camcorder.
142
Condensation
Moving the camcorder rapidly between hot and cold temperature may cause
condensation (water droplets) to form on its internal surfaces. Stop using the
camcorder if condensation is detected. Continued use may damage the camcorder.
E
Condensation may form in the following cases:
When the camcorder is moved from an
When the camcorder is moved from a
air-conditioned room to a warm, humid
cold place to a warm room
place
When the camcorder is left in a humid
room
When a cold room is heated rapidly
How to avoid condensation:
❍ Unload the cassette, place the camcorder in an airtight plastic bag and let it adjust
to temperature changes slowly before removing it from the bag.
When condensation is detected:
Resuming use:
Additional
Information
❍ The camcorder stops operating and the warning message “CONDENSATION HAS
BEEN DETECTED” appears for approx. 4 seconds and h starts flashing.
❍ If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and
v starts flashing. Remove the cassette immediately and leave the cassette
compartment open. Leaving the cassette in the camcorder may damage the tape.
❍ A cassette cannot be loaded when condensation is detected.
❍ It takes about 1 hour until the water droplets evaporate. After the condensation
warning stops flashing, wait for 1 more hour before resuming use.
143
Using the Camcorder Abroad
Power Sources
E
You can use the compact power adapter to operate the camcorder and to charge
battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz.
Consult the Canon Service Center for information on plug adapters for overseas use.
Playback on a TV Screen
You can only play back your recordings on TVs with NTSC system. The NTSC system is
Additional
Information
used in the following countries/areas:
American Samoa, Antigua, Aruba, Bahamas, Barbados, Bermuda, Bolivia, Canada,
Chile, Columbia, Costa Rica, Cuba, Ecuador, El Salvador, Guam, Guatemala, Greenland,
Haiti, Honduras, Jamaica, Japan, Korea, Mexico, Micronesia, Myanmar, Nicaragua,
Panama, Peru, Philippines, Puerto Rico, Saint Kitts and Nevis, Saint Lucia, Saint Vincent
and the Grenadines, Surinam, Taiwan, Trinidad and Tobago, USA, Venezuela, Virgin
Islands.
144
Troubleshooting
If you have a problem with your camcorder, refer to this checklist. Consult your dealer
or a Canon Service Center if the problem persists.
E
Power Source
Problem
Camcorder will not turn
on.
The camcorder switches
off by itself.
Cassette compartment
will not open.
Cassette compartment
stopped during loading/
unloading.
LCD/viewfinder switches
on and off.
Cause
Battery pack is exhausted.
Battery pack is not correctly
attached.
Battery pack is exhausted.
Power save function has
been activated.
Battery pack is exhausted.
Solution
Replace or charge the
battery pack.
Attach the battery pack
correctly.
Replace or charge the
battery pack.
Turn on the camcorder.
Replace or charge the
battery pack.
Cassette compartment cover Open the cassette
is not fully open.
compartment cover fully.
Replace or charge the
Battery pack is exhausted.
battery pack.
Consult a Canon Service
The camcorder
Center.
malfunctions.
Replace or charge the
Battery pack is exhausted.
battery pack.
16
16
16
28
16
22
16
–
16
Recording/Playback
Buttons will not work.
k flashes on the
screen.
h flashes on the screen.
“Remove the cassette”
appears on the screen.
The wireless controller
will not work.
Camcorder is not turned on.
Cassette is not loaded.
Battery pack is exhausted.
28
22
16
143
22
Change the remote sensor
modes.
49
Replace the batteries.
24
Additional
Information
Condensation is detected.
Camcorder stopped
operating to protect the
tape.
Camcorder and wireless
controller are not set to the
same remote sensor mode.
Batteries of the wireless
controller are exhausted.
Turn on the camcorder.
Load a cassette.
Replace or charge the
battery pack.
See reference page.
Unload and reload the
cassette.
145
Recording
E
Problem
Image will not appear
on the screen.
“Set the time zone, date
and time” appears on
the screen.
Pressing the start/stop
button will not start
recording.
Camcorder will not
focus.
A vertical light bar
appears on the screen.
Sound is distorted or
recorded in a lower
volume than the actual
volume.
Viewfinder picture is
blurred.
Cause
Camcorder is not set to
CAMERA mode.
Time zone, date and time
are not set, or the backup
battery is exhausted.
Solution
28
Set the camcorder to
CAMERA mode.
25
Set the time zone, date and
time, or replace the backup
battery and reset the date
and time.
28
Camcorder is turned off.
Turn on the power.
22
Cassette is not loaded.
Load a cassette.
22
Rewind the tape or replace
Tape reached the end (
the cassette.
flashes on the screen).
23
Replace the tape or change
Cassette is protected (v
the position of the protect
flashes on the screen).
switch.
28
Set the camcorder to
Camcorder is set to a mode
other than the CAMERA mode. CAMERA mode.
75
Autofocus does not work on Focus manually.
that subject.
20
Adjust the viewfinder with
Viewfinder is not adjusted.
the diopter adjustment lever.
141
Clean the lens.
Lens is dirty.
–
Bright light in a dark scene
may cause a vertical light
–––
bar (smear) to appear. This is
not a malfunction.
–
When recording near loud
sound (such as fireworks,
drums or concerts), sound
–––
may become distorted or
may not be recorded in the
actual sound level. This is
not a malfunction.
20
Adjust the viewfinder with
Viewfinder is not adjusted.
the diopter adjustment lever.
Playback
Additional
Information
Pressing the playback
button does not start
playback.
146
Camcorder is turned off, or is
not set to PLAY (VCR) mode.
Cassette is not loaded.
Tape reached the end (
flashes on the screen).
Image will not appear
[AV/PHONES] is set to
on the TV screen.
[PHONESH] in the menu.
[AV / DV OUT] is set to
[ON].
Tape is running, but
TV/VIDEO selector on the TV
image will not appear
is not set to VIDEO.
on the TV screen.
Video heads are dirty.
You attempted to play back
or dub copyright protected
tape.
No sound from the built- Speaker volume is turned
in speaker.
off.
Set the camcorder to PLAY
(VCR) mode.
Load a cassette.
Rewind the tape.
37
Set [AV/PHONES] to [AV] in
the menu.
Set [AV / DV OUT] to [OFF].
39
Set the selector to VIDEO.
42
Clean the video heads.
Stop playback/dubbing.
142
91
Adjust the volume with the
selector dial.
40
22
37
93
ZR70 MC ZR65 MC
Memory Card Operation
Problem
Memory card cannot be
inserted.
Memory card cannot be
recorded.
Cause
Solution
Memory card was not facing Turn the memory card over
and reinsert it.
the correct direction.
Replace the memory card or
Memory card is full.
erase images.
Format the memory card.
Memory card is not
formatted.
Memory card is not inserted. Insert a memory card.
Set [FILE NUMBERS] to
File number reached
[RESET] and insert a new
maximum value.
memory card.
SD Memory Card is
Change the position of the
protected.
protect switch.
Memory card cannot be Camcorder is not set to
Set the camcorder to CARD
played back.
PLAY (VCR) mode.
CARD PLAY (VCR) mode.
Memory card is not inserted. Insert a memory card.
Image cannot be erased. Image is protected.
Cancel the protection.
Change the position of the
SD memory card is
protect switch.
protected.
flashes red.
Turn off the camcorder.
Card error occurred.
Remove and reinsert the
memory card. Format the
memory card if flashing
persists.
100
E
115
128
100
102
100
111
100
114
100
128
Additional
Information
147
System Diagram
(Availability differs from area to area)
E
WS-20 Wrist Strap
ZR70 MC
SS-800 Shoulder Strap
WA-30.5 Wide
Attachment
ZR70 MC ZR65 MC
WD-30.5 Wideconverter
WL-D79 Wireless
Controller
ZR60 WL-D80
Wireless Controller
BP-500 Series
Battery Pack
CG-570
Battery Charger
CB-570
Car Battery Cable
MiniDV
Video
Cassette
TL-30.5 Teleconverter
CA-570 Compact
Power Adapter
FS-30.5U
Filter Set
BP-500 Series
Battery Pack
ZR70 MC VL-3 Video Light
S-150 S-video Cable
TV
STV-250N
Stereo Video Cable
VCR
ZR70 MC DM-50 Directional
Stereo Microphone
Commercially available
DV Cable
Digital Device
ZR70 MC ZR65 MC
PC Card Adapter
BP-900 Series
Battery Pack*
VL-10Li
Battery
Video Light
Stereo Microphone
(commercially
available)
SD Memory Card
USB Reader/Writer
FD Adapter
MultiMediaCard
Computer
Additional
Information
IFC-300PCU
USB Cable
Bubble Jet Printer
with direct print
function
SC-1000 Soft
Carrying Case
SC-A50 Soft
Carrying Case
* Charging with the CA-920 Compact Power Adapter or CH-910 Dual Battery
Charger/Holder (both optional)
148
Optional Accessories
Call or visit your local retailer/dealer for genuine Canon video accessories. You can also
obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040,
Canon U.S.A. Information Center.
BP-500 Series Battery Packs
BP-512
BP-522
E
BP-535
When you need extra battery packs, select from
the following: BP-511, BP-512, BP-522 or BP-535.
CG-570 Battery Charger
The battery charger can be used with the
supplied CA-570 Compact Power Adapter or the
optional CB-570 Car Battery Cable to charge BP500 series battery packs.
Battery Pack
Charging Time
BP-508 (ZR65 MC/ZR60)
55 min.
BP-512 (ZR70 MC/Optional)
95 min.
BP-511 (Optional)
95 min.
BP-522 (Optional)
140 min.
BP-535 (Optional)
205 min.
CB-570 Car Battery Cable
Use the car battery cable with the CG-570
Battery Charger to charge battery packs on the
move. The car battery cable plugs into your
car’s cigarette lighter and runs off a 12-24 V DC
negative ground battery.
TL-30.5 Tele-converter
Additional
Information
This tele-converter lens increases the focal
length of the camcorder lens by a factor of 1.9.
• The image stabilizer is not as effective when
the tele-converter is attached.
• The image quality may be degraded at the telephoto side.
• The minimum focusing distance with the Tele-converter is 13.1 ft (4 m); 1.6 in. (4 cm)
on maximum wide angle.
149
WD-30.5 Wide-converter
This lens decreases focal length by a factor of
0.7, giving you a wide perspective for indoor
E
shots or panoramic views.
FS-30.5U Filter Set
Neutral density and MC protector filters help
you to control difficult lighting conditions.
VL-10Li Battery Video Light
This compact yet powerful video light can be
used for both indoor and outdoor shooting.
The video light is powered by BP-900 series
battery packs.
• Approximate usage time: BP-915: 60 min., BP-930: 120 min., BP-945: 170 min.
• BP-900 series battery packs are charged with the CA-920 Compact Power Adapter
(optional).
ZR70 MC
VL-3 Video Light
This video light enables you to record brightly
in color even in dark places. It attaches to the
camcorder’s advanced accessory shoe for cablefree operation.
Additional
Information
ZR70 MC DM-50 Directional Stereo
Microphone
This highly sensitive, super-directional
microphone attaches to the camcorder’s
advanced accessory shoe. It can be used as
directional microphone (monaural) or stereo
microphone.
WS-20 Wrist Strap
Use this for extra additional protection for
active shooting.
150
SC-1000 Soft Carrying Case
A handy camcorder bag with padded
compartments and plenty of space for
E
accessories.
SC-A50 Soft Carrying Case
This lightweight bag keeps the camcorder
within easy reach without weighing you down
or getting in the way.
O
RY CA
SO
N GENU
NO
VI
INE DE
This mark identifies genuine Canon video accessories. When you
use Canon video equipment, we recommend Canon-brand
accessories or products bearing the same mark.
ACCES
Provided Accessories:
WL-D79 Wireless Controller (ZR70 MC/ZR65 MC)
WL-D80 Wireless Controller (ZR60)
SS-800 Shoulder Strap
Lens Cap
CA-570 Compact Power Adapter
BP-512 Battery Pack (ZR70 MC)
BP-508 Battery Pack (ZR65 MC/ZR60)
STV-250N Stereo Video Cable
IFC-300PCU USB Cable (ZR70 MC/ZR65 MC)
WA-30.5 Wide Attachment
D83-0622-000
D83-0652-000
D81-1430-000
D52-0220-000
8468A002AA
6760A002AA
D85-1360-000
3067A002AA (D82-0590-201)
6906A001AA
D55-0170-000
Optional Accessories:
3055A002AA (D85-1112-201)
3174A002AA (D85-1122-201)
6741A002AA
3083A002AA (D81-1200-201)
D81-1302-201
6739A002AA
6740A002AA
6738A002AA
3176A002AA (D84-0120-201)
3175A002AA (D86-0121-201)
3140A002AA (D86-0081-201)
3141A002AA (D86-0090-201)
3118A002AA (D81-0190-202)
3134A002AA (D36-0032-201)
Additional
Information
BP-511 Battery Pack
BP-522 Battery Pack
BP-535 Battery Pack
SC-1000 Soft Carrying Case
SC-A50 Soft Carrying Case
WD-30.5 Wide-converter
TL-30.5 Tele-converter
F-30.5U Filter Set
DM-50 Directional Stereo Microphone
VL-3 Video Light
VL-10Li Battery Video Light
JR 7.2V 10WF Halogen Bulb
WS-20 Wrist Strap
DVM-CL DV Cleaning Cassette
151
Specifications
E
ZR70 MC/ZR65 MC/ZR60
Power supply (rated):
Power consumption
(AF turned on):
Television system:
Video recording system:
Audio recording system:
Image sensor:
Additional
Information
Tape format:
Tape speed:
Maximum recording time
(80 min. cassette):
Fast forward/rewind time:
Lens:
152
7.4 V DC
2.9 W (Using viewfinder), 3.8 W (Using LCD screen)
EIA standard (525 lines, 60 fields) NTSC color signal
2 rotary heads, helical scanning DV system (Consumer digital VCR
SD system); Digital component recording
PCM digital sound: 16 bit (48 kHz/2 ch); 12 bit (32 kHz/4 ch)
1/6“ CCD (charge coupled device), approx. 680,000 pixels
(Effective pixels: tape: approx. 340,000 pixels, card*1: approx.
447,000 pixels)
Videocassettes bearing the “MiniDV” mark.
SP: 0.74 ips (18.81 mm/s), LP: 0.49 ips (12.56 mm/s)
SP: 80 min., LP: 120 min.
Approx. 2 min. 20 sec. (with a 60 min. cassette)
ZR70 MC: F1.6-3.6, 22x power zoom, f=2.8-61.6 mm;
ZR65 MC: F1.6-3.2, 20x power zoom, f=2.8-56 mm;
ZR60 MC: F1.6-2.9, 18x power zoom, f=2.8-50.4 mm
Focusing system:
TTL autofocus, manual focusing possible
Minimum focusing distance: 3.3 ft. (1 m), 0.39 in. (1 cm) on maximum wide angle
Maximum shutter speed:
1/2,000 sec. (1/250 sec. when using a memory card)
Minimum illumination:
1.6 lx (using the Night mode in CAMERA mode)
Recommended illumination: More than 100 lx
Filter diameter:
30.5 mm
Viewfinder:
0.33 in., TFT color LCD, approx. 113,000 pixels
LCD screen:
2.5 in., TFT color, approx. 112,000 pixels
Microphone:
Stereo electret condenser microphone
Recording media*1:
SD Memory Card, MultiMediaCard
Number of recording pixels*1: Still image: 1024 x 768, 640 x 480 pixels
Movie*2: 320 x 240 pixels (approx. 10 sec.), 160 x 120 pixels
(approx. 30 sec.), 15 frames/sec.
The figures in brackets represent the maximum length of one
movie clip.
Estimated SD Memory Card 1024 x 768: Superfine: 14 images/Fine: 20 images/Normal 39
images;
SDC-8M capacities*1:
640 x 480: Superfine: 35 images/Fine 52 images/Normal 86 images
The actual number varies according to the images. Sample images recorded on the supplied SD
Memory Card are to be included in the total number.
Design rule for Camera File system (DCF), Exif 2.2 compliant,
File format*1:
Digital Print Order Format (DPOF) compliant (still images only)
This camcorder supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing the
communication between camcorders and printers. By connecting to an Exif Print-compliant printer,
the camcorder’s image data at the time of shooting is used and optimized, yielding extremely high
quality prints.
Still image: JPEG (Compression mode: Superfine, Fine, Normal),
Image format*1:
Movie: Motion JPEG
*1 ZR70 MC/ZR65 MC only
*2 ZR70 MC only
USB terminal*1:
DV terminal input/output:
AV terminal input/output:
S-video terminal
input/output:
MIC terminal input:
Headphone terminal:
Operating temperatures:
Dimensions:
Weight:
mini-B
Special 4-pin connector (IEEE 1394 compliant)
ø3.5 mm minijack
Audio input: -10 dBV/40 kohms or more
Audio output: -10 dBV (47 kohm load)/3 kohms or less
Video:
1 Vp-p/75 ohms unbalanced
1 Vp-p/75 ohms (Y signal), 0.286 Vp-p/75 ohms (C signal)
E
ø3.5 mm stereo mini-jack
–57 dBV (with 600 ohm mic)/5 kohms or more
ø3.5 mm stereo minijack
32 – 104˚F (0 – 40˚C)
4.1 × 2.3 × 5.8 in. (103 × 58 × 147 mm)
ZR70 MC: 1.2 lb. (525 g), ZR65 MC/ZR60: 1.2 lb. (520 g)
*1 ZR70 MC/ZR65 MC only
CA-570 Compact Power Adapter
Power supply:
Power consumption:
Rated output:
Operating temperature:
Dimensions:
Weight:
100 – 240 V AC, 50/60 Hz
17 W
8.4 V DC, 1.5 A
32 – 104˚F (0 – 40˚C)
2.1 × 3.5 × 1.1 in. (52 × 90 × 29 mm)
4.8 oz. (135 g)
BP-512/BP-508 Battery Pack
Battery type:
Rated voltage:
Operating temperature:
Battery capacity:
Dimensions:
Weight:
Rechargeable Lithium Ion Battery
7.4 V DC
32 – 104˚F (0 – 40˚C)
BP-512: 1100 mAh, BP-508: 800 mAh
1.5 × 0.83 × 2.2 in. (38 × 21 × 55 mm)
BP-512: 2.5 oz. (70g), BP-508: 2.3 oz. (65g)
SDC-8M SD Memory Card
8 MB
SD Memory Card standard
32 – 104˚F (0 – 40˚C)
1.3 × 0.94 × 0.08 in. (32 × 24 × 2.1 mm)
0.07 oz. (2 g)
Weight and dimensions are approximate. Errors and omissions excepted. Subject to
change without notice.
Additional
Information
Capacity:
Interface:
Operating temperature:
Dimensions:
Weight:
153
Index
E
12bit audio . . . . . . . . . . . . . . . . . . 98
16:9 wide screen . . . . . . . . . . . . . . 52
6-second auto date . . . . . . . . . . . . 84
Digital zoom . . . . . . . . . . . . . . . . . 30
Direct print function *2 . . . . . . . . 118
DV dubbing. . . . . . . . . . . . . . . . . . 90
DV terminal . . . . . . . . . . . . . . . 88, 99
A
Abroad, using the camcorder . . . 144
Accessories. . . . . . . . . . . . . . . . 9, 149
Accessory shoe . . . . . . . . . . . . . . 150
Advanced accessory shoe *1 . . . . . 73
Analog line-in . . . . . . . . . . . . . . . . 89
Analog-digital converter. . . . . . . . 92
Assist lamp *1 . . . . . . . . . . . . . . . . 59
Audio dubbing . . . . . . . . . . . . . . . 96
Audio mode . . . . . . . . . . . . . . . . . 71
Auto . . . . . . . . . . . . . . . . . . . . . . . 57
Autofocus . . . . . . . . . . . . . . . . . . . 75
AV insert . . . . . . . . . . . . . . . . . . . . 94
AV/DV . . . . . . . . . . . . . . . . . . . . . 92
AV/headphones terminal . . . . 39, 41
E
Easy recording. . . . . . . . . . . . . . . . 57
Effects . . . . . . . . . . . . . . . . . . . . . . 65
Erasing still images *2 . . . . . . . . . 115
Exposure . . . . . . . . . . . . . . . . . . . . 77
F
Faders . . . . . . . . . . . . . . . . . . . . . . 62
Fast forward . . . . . . . . . . . . . . . . . 37
File numbers *2 . . . . . . . . . . . . . . 103
Focusing . . . . . . . . . . . . . . . . . . . . 75
Formatting *2 . . . . . . . . . . . . . . . 128
G
Grip belt . . . . . . . . . . . . . . . . . . . . 20
B
Backup battery . . . . . . . . . . . . . . . 19
Battery charger . . . . . . . . . . . . . . 149
Battery pack . . . . . . . . . . . . . . . . . 16
Beep . . . . . . . . . . . . . . . . . . . . . . . 52
Brightness . . . . . . . . . . . . . . . . . . . 33
Additional
Information
C
Card animation *2 . . . . . . . . . . . . 123
Card mix *2 . . . . . . . . . . . . . . . . . 122
Computer . . . . . . . . . . . . . . . 99, 129
Condensation . . . . . . . . . . . . . . . 143
Connections - TV . . . . . . . . . . . . . . 41
Connections - VCR. . . . . . . . . . . . . 41
Copyright signals. . . . . . . . . . . . . . 91
Copying still images*2 . . . . . . . . . 126
I
Image quality *2 . . . . . . . . . . . . . 101
Image stabilizer. . . . . . . . . . . . . . . 69
Index screen *2 . . . . . . . . . . . . . . 112
L
LCD mirror mode . . . . .
LCD screen. . . . . . . . . . .
Lens cap . . . . . . . . . . . .
Light-up buttons *1 . . . .
Low light mode. . . . . . .
Low light plus mode *1 .
LP mode . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
33
32
20
51
58
59
54
D
Data code . . . .
Date and time .
Date search . . .
Demo mode . .
Digital effects .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
*1 ZR70 MC , *2 ZR70 MC ZR65 MC
154
H
Headphones . . . . . . . . . . . . . . . . . 39
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
83
25
85
53
61
M
Magnifying the image . . . . . . . . . 82
Maintenance . . . . . . . . . . . . . . . . 141
Manual focus . . . . . . . . . . . . . . . . 75
Memory card *2 . . . . . . . . . . . . . 101
Menus . . . . . . . . . . . . . . . . . . . . . . 44
Microphone. . . . . . . . . . . . . . . . . . 71
MIC terminal . . . . . . . . . . . . . . . . . 71
Movie size *1 . . . . . . . . . . . . . . . . 102
MultiMediaCard *2 . . . . . . . . . . . 101
Multi-image screen . . . . . . . . . . . . 67
My Camera settings . . . . . . . . . . . 50
N
Night mode . . . . . . . . . . . . . . . . . . 59
O
Output channel. . . . . . . . . . . . . . . 43
Search select . . . . . . . . . . . . . . . . . 85
Self-timer . . . . . . . . . . . . . . . . . . . 70
Shutter sound *2 . . . . . . . . . . . . . 105
Shutter speed . . . . . . . . . . . . . . . . 78
Slide show *2 . . . . . . . . . . . . . . . . 112
SP mode . . . . . . . . . . . . . . . . . . . . 54
Speaker . . . . . . . . . . . . . . . . . . . . . 39
Sports mode . . . . . . . . . . . . . . . . . 58
Spotlight mode . . . . . . . . . . . . . . . 58
Still image quality *2 . . . . . . . . . . 101
Still image size *2 . . . . . . . . . . . . 101
Stitch Assist mode *2 . . . . . . . . . . 107
Super Night mode *1 . . . . . . . . . . 59
S-video/S1-video . . . . . . . . . . . . . . 41
E
P
Photo search . . . . . . . . . . . . . . . . . 85
Playback - Memory card *2 . . . . . 111
Playback - Tape . . . . . . . . . . . . . . . 37
Playback pause . . . . . . . . . . . . . . . 38
Portrait mode . . . . . . . . . . . . . . . . 58
Power adapter . . . . . . . . . . . . . . . 15
Print order *2 . . . . . . . . . . . . . . . 116
Protect *2 . . . . . . . . . . . . . . . . . . 114
R
U
USB terminal *2 . . . . . . . . . . . . . . 129
V
Video. . . . . . . . . . . . . . . . . . . . . . . 41
Video heads. . . . . . . . . . . . . . . . . 142
Video ID-1 system . . . . . . . . . . . . . 41
Video light. . . . . . . . . . . . . . . 73, 150
Videocassettes . . . . . . . . . . . . . . . . 22
Viewfinder . . . . . . . . . . . . . . . . . . 20
W
White balance . . . . . . . . . . . . . . . . 80
Wide screen. . . . . . . . . . . . . . . . . . 52
Wireless controller . . . . . . . . . . . . 24
S
S1 video terminal . . . . . . . . . . . . . 41
Sample images *2 . . . . . . . . . . . . 132
Sand & Snow mode. . . . . . . . . . . . 58
Screen displays . . . . . . . . . . . . . . 134
SD Memory Card *2 . . . . . . . . . . . 101
*1 ZR70 MC , *2 ZR70 MC ZR65 MC
Z
Additional
Information
Recording to a VCR . . . . . . . . . . . . 87
Record pause mode . . . . . . . . . . . 29
Record review . . . . . . . . . . . . . . . . 35
Record search . . . . . . . . . . . . . . . . 35
Recording Movies (tape) . . . . . . . . 28
Recording Movies
(memory card) *1 . . . . . . . . . . . 109
Recording Still Images (tape) . . . . 55
Recording Still Images
(memory card) *2 . . . . . . . . . . . 104
Recording programs . . . . . . . . . . . 57
Remote sensor. . . . . . . . . . . . . . . . 24
Rewind . . . . . . . . . . . . . . . . . . . . . 37
T
Tape protection. . . . . . . . . . . . . . . 23
Telephoto . . . . . . . . . . . . . . . . . . . 30
Time code . . . . . . . . . . . . . . . . . . . 86
Time zone . . . . . . . . . . . . . . . . . . . 25
Tripod . . . . . . . . . . . . . . . . . . . . . . 36
Troubleshooting . . . . . . . . . . . . . 145
TV Screen. . . . . . . . . . . . . . . . 41, 134
Zero set memory . . . . . . . . . . . . . . 86
Zooming . . . . . . . . . . . . . . . . . . . . 30
155
U.S.A.
E
CANON® ZR70 MC/ZR65 MC/ZR60 DIGITAL VIDEO CAMCORDER LIMITED
WARRANTY
The limited warranty set forth below is given by Canon U.S.A., Inc. (“CUSA”) with respect to each Canon ZR70 MC/
ZR65 MC/ZR60 Digital Video Camcorder (“DV Camcorder”) purchased and used in the United States.
Each Canon DV Camcorder, when delivered to you in new condition in its original container, is warranted against defective
material or workmanship as follows: for a period of one (1) year from the date of original purchase (three (3) months in the
case of the video head part), defective parts or DV Camcorders returned to a CUSA factory service center (“CUSA Center”)
or an authorized DV Camcorder service facility (“Service Facility”), and proven to be defective upon inspection, will be
repaired or exchanged for new or comparable rebuilt parts or DV Camcorders. The warranty period for repaired or
replacement parts or DV Camcorders shall begin upon shipment of the same, but shall in no event exceed the original
warranty period of the defective part or DV Camcorder.
Non-Canon brand peripheral equipment and software which may be distributed with Canon DV Camcorders are
sold “AS IS”, without warranty of any kind by CUSA, including any implied warranty regarding merchantability
or fitness for a particular purpose. The sole warranty with respect to such non-Canon brand items is given by
the manufacturer or producer thereof.
CUSA shall have no responsibility under this limited warranty for use of Canon DV Camcorders in conjunction with
incompatible peripheral equipment and incompatible software.
In order to obtain warranty service, contact the authorized Canon retail dealer from whom you purchased the DV
Camcorder or call the CANON INFORMATION CENTER AT 1-800-828-4040 (which is open from 9:00 a.m. to 5:00 p.m.
(E.S.T.), Monday through Friday, excluding holidays). Have your unit serial number and your date of purchase available
when you make the call to expedite service. In either case you will be directed to ship the DV Camcorder, postage prepaid,
to the CUSA Center or Service Facility nearest to you. You must include a copy of the proof of purchase (bill of sale) and a
complete explanation of the problem. DV Camcorders covered by this limited warranty will be repaired and returned to you
without charge by the CUSA Center or the Service Facility. Repairs not under warranty will be at such cost as the CUSA
Center or Service Facility may from time to time generally establish.
This limited warranty covers all defects encountered in normal use of the DV Camcorder, and does not apply in the
following cases:
(a) Loss of or damage to the DV Camcorder due to abuse, mishandling, improper packaging by you, alteration, accident,
leaking batteries, exterior nicks, scratches or dents, electrical current fluctuations, failure to follow operating
instructions, maintenance and environmental instructions prescribed in CUSA’s instruction manual, or service performed
by other than a CUSA Center or Service Facility.
(b) Use of parts or supplies (other than those sold by CUSA) which cause damage to the DV Camcorder or cause
abnormally frequent service calls or service problems.
(c) If any DV Camcorder has had its serial number or dating altered or removed.
Additional
Information
This limited warranty does not apply to accessories or consumables for the DV Camcorder, which are sold “AS IS”, without
warranty of any kind by CUSA.
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, APPLIES TO THE DV CAMCORDER AFTER THE APPLICABLE PERIOD OF EXPRESS
WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED
ABOVE, GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THE DV CAMCORDER SHALL BIND
CUSA. (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU) CUSA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS,
EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OF DATA, OR ANY OTHER
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE
DV CAMCORDER, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CUSA HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CUSA
BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE DV CAMCORDER SOLD BY CUSA AND CAUSING
THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS,
DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF
USE, MISUSE OR INABILITY TO USE THE DV CAMCORDER NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CUSA.
(SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.) THIS LIMITED WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL PURCHASER OF ANY DV CAMCORDER, OR THE PERSON FOR WHOM IT
WAS PURCHASED AS A GIFT, AND STATES YOUR EXCLUSIVE REMEDY.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Canon U.S.A., Inc.
One Canon Plaza
Lake Success, New York 11042
156
CANADA
CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY
The limited warranty set forth below is given by Canon Canada Inc. (“Canon Canada”) with respect to Canon digital video equipment purchased
in Canada. This limited warranty is only effective upon presentation of a bill of sale or other proof of purchase for this Canon digital video
equipment to a Canon Service Facility when repairs are required.
Canon consumer video digital equipment is warranted under normal, non-commercial, personal use, against defective materials or workmanship
as follows:
Parts: Defective parts will be exchanged for new parts or, at Canon Canada’s option, comparable rebuilt parts for a period of one year from the
date of original purchase, except Video Heads which will be exchanged for a period of 3 months from the date of purchase.
Labour: For a period of one year from the date of original purchase, labour will be provided free of charge by our Canon Service Facilities in
Canada.
This limited warranty covers all defects except where:
(a) The loss or damage to the product results from:
i)
accident, natural disaster, mishandling, abuse, neglect, unauthorized product modification or failure to follow instructions contained in
the instruction manual;
ii) the use of accessories, attachments, products, supplies, parts or devices with this Canon product that do not conform to Canon
specifications or that cause abnormally frequent service problems;
iii) repairs or services performed by any party other than a Canon Service Facility;
iv) defective batteries or any exposure to water, sand or dirt;
v) shipping (claim must be presented to the shipper);
(b) Any serial number on the video equipment is altered or removed.
(c) The digital video equipment is used for commercial, professional or industrial purposes.
This limited warranty does not cover the cabinet (exterior finish) of the digital video equipment, video cassette tapes, head cleanings, nor does it
apply to digital video equipment purchased outside Canada.
E
TO OBTAIN WARRANTY SERVICE
Ship your Canon digital video equipment in its original carton, box or equivalent, properly packed, fully insured with shipping charges prepaid,
together with a copy of your bill of sale or other proof of purchase and a description of the problem to any of the Canon Service Facilities in
Canada.
LIMITATIONS
Except as otherwise required by applicable legislation, this warranty is in lieu of all other warranties, conditions, guarantees or representations,
express or implied, statutory or otherwise, relative to this Canon product, including implied warranties or conditions of merchantability or fitness
for a particular purpose.
Canon Canada assumes no liability for special, consequential or incidental damages or loss that may arise, whether on account of negligence or
otherwise, from the use, misuse or inability to use this Canon product (including loss of profit, revenue, video tapes or enjoyment) or from failure
to conform to any express or implied warranties, conditions, guarantees or representations. Any recovery under this limited warranty shall not
exceed the purchase price of the product. Canon Canada does not assume or authorize any other person to assume for Canon Canada any other
liability with respect to this Canon product.
This warranty does not extend to any person other than the original purchaser of this Canon product or the person for whom it was purchased as
a gift and states your exclusive remedy.
NOTICE TO CONSUMER
If you plan to take important videos or if the product has not been used for some time, please check all functions with the instruction book
before using it.
Additional
Information
157
CANON INC.
U.S.A.
CANON U.S.A., INC. NEW JERSEY OFFICE
100 Jamesburg Road, Jamesburg, NJ 08831 USA
CANON U.S.A., INC. CHICAGO OFFICE
100 Park Blvd., Itasca, IL 60143 USA
CANON U.S.A., INC. LOS ANGELES OFFICE
15955 Alton Parkway, Irvine, CA 92618 USA
CANON U.S.A., INC. HONOLULU OFFICE
210 Ward Avenue, Suite 200, Honolulu, HI 96814 USA
● If you have any questions, call the Canon U.S.A. Information
Center toll-free at 1-800-828-4040 (U.S.A. only).
CANADA
CANON CANADA INC. NATIONAL HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7
CANON CANADA INC. CALGARY
2828, 16th Street, N.E. Calgary, Alberta T2E 7K7
CANON CANADA INC. MONTREAL
5990 Côte de Liesse, Quebec H4T 1V7
● If you have any questions, call the Canon Canada Information
Center toll-free at 1-800-828-4040. (Canada only)
● Si vous avez des questions, veuillez téléphoner sans frais au
Canada 1-800-828-4040. (Canada seulement)
MEXICO
CENTRO Y
SURAMÉRICA
ASIA
CANON MEXICANA, S. DE R.L. DE C.V.
Periferico Sur No. 4124 Col. Ex-Rancho de Anzaldo C.P. 01900
México, D.F., México
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, FL 33126 USA
CANON HONGKONG COMPANY LTD.
9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong
Printed on 100% reused paper.
Document réalisé avec du papier recyclé à 100%.
El papel aqui utilizado es 100% reciclado.
PUB.DIM-519
0000A/AB0.0
© CANON INC. 2003
DY8-9120-360-000
PRINTED IN JAPAN
IMPRIME AU JAPON
IMPRESO EN JAPÓN
Download PDF

advertising