Addlogix iDP-3410 Printer User Manual

CITIZEN
User's Manual
Model : iDP-3410
Dot Matrix Printer
Rev.1.00 Newly issued on 20.Oct.1998
Japan CBM Corporation
Information Systems Div.
iDP-3410 User’s Manual
Declaration of Conformity
Manufacturer’s Name :
Manufacturer’s Address
Declare the Product
Product Name
Model Number(s)
: Japan CBM Corporation
: CBM Bldg., 5-68-10, Nakano, Nakano-ku
Tokyo, 164-0001, Japan
Dot Matrix Printer
iDP-3410
(iDP-3410R/P, iDP-3410S/C, iDP-3410T/I)
(S.NO.98X0001 - )
Conform to the following Standards
LVD
EMC
: EN60950
: EN55022
: EN61000-3-2
: EN61000-3-3 : 1995
: EN50082-1
: IEC801-2
: IEC801-3
: IEC801-4
: 1992+A1+A2+A3+A4
: 1994 Class A
: 1995
: 1992
: 1991 4KV CD, 8KV AD
: 1984 3V/m, 26MHz-1000MHz AM1KHz 80%
: 1988±0.5KV Signal Line±1KV AC mains
Supplementary Information
“The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and
the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC”
Place
Date
Tokyo, Japan
Signature
September.1998
Full Name : Mikio Moriya
Position : General Manager
R & D Department
Europe Contact :
Norco Declaration AB
Box 7146 S-250 07 Helsingborg Sweden
Warning
This is a Class A products. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
This declaration is applied only for 230V model.
iDP-3410 User’s Manual
IMPORTANT SAFETY INSTRUCTIONS
•Read all of these instructions and save them for future reference.
•Follow all warnings and instructions marked on the product.
•Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
•Do not use this product near water.
•Do not place this product on an unstable cart, stand or table. The product may fall, causing serious
damage to the product.
•Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable
operation of the product and to protect it from overheating, do not block or cover these openings. The
openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface.
This product should never be placed near or over a radiator or heater. This product should not be placed
in an built-in installation unless proper ventilation is provided.
•This product should be operated from the type of power source indicated on the marking label. If you re
not sure of the type of power available, consult your dealer or local power company.
•Do not allow anything to rest on the power cord. Do not place this product where the cord will be walked
on.
•If an extension cord is used with this product, make sure that the total of the ampere ratings of the
products plugged into the extension cord does not exceed the extension cord ampere rating. Also, make
sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
•Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of
any kind on the product.
•Except as explained elsewhere in this manual, do not attempt to service this product by yourself. Opening
and removing the covers that are marked “Do Not Remove” may expose you to dangerous voltage
points or other risks. Refer all servicing on those compartments to service personnel.
•Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions are followed. Adjust only
those controls that are covered be the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to
restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for service.
•Please keep the poly bag which this equipment is packed in away from children or throw it away to
prevent children from putting it on. Putting it on may cause suffocation.
WICHTIGE SICHERHEITSANWEISUNGEN
•Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf.
•Befolgen Sie alle auf dem Drucker vermerkten Hinweise und Anweisungen. Vor dem Reinigen
iDP-3410 User’s Manual
grundsätzlich Stecker aus der Steckdose ziehen. Keine Flüssigkeiten oder Aerosolreiniger benutzen.
Nut mit einem feuchten Tuch abwischen.
•Der Drucker darf nicht in der Nähe von Wasser aufgestellt werden.
•Drucker nicht auf einem unstabilen Wagen, Stand oder Tisch aufstellen. Der Drucker könnte
herunterfallen und dabel beschädigt werden.
•Schlitze und Öffnungen im Gehäuse, in der Rückwand und im Boden dienen der Belüftung. Sie dürfen
keinesfalls zugedeckt oder blockiert werden, da sich der Drucker sonst überhitzt. Drucker nicht auf ein
Bett, Sofa, Teppich oder dergleichen stellen. Drucker nicht in der Nähe eines Heizkörpers aufstellen.
Drucker darf nicht eingebaut werden, falls nicht für ausreichende Belüftung gesorgt ist.
•Drucker nur mit der auf dem Typschild angegebenen Spannung betreiben. Wenn Sie sich nicht sicher
sind, fragen Sie ihren Händler oder ihr zuständiges Elektrizitätswerk.
•Nichts auf das Stromanschlußkabel stellen. Kabel muß so verlegt werden, daß man nicht darauftreten
kann.
•Ein etwaiges Verlängerungskabel muß der Stromstärke aller daran angeschlossenen Geräte entsprechen.
•Keine Gegenstände in die Gehäuseschlitze schieben.
•Drucker darf nur da gewartet werden, wo im Handbuch angegeben, Öffnen und. Abnehmen von
Abdeckungen, die mit “Do not remove” gekennzeichenet sind, könnte gefährliche spannungführende
Stellen oder sonstige Gefahrenpunkte freilegen. Die Wartung solcher Stellen darf grundsätzlich nur von
besonders ausgebildetem Fachpersonal vorgenommen werden.
A. Wenn das Stromanschlußkabel oder der Stecker beschädigt oder durch-gescheuert ist.
B. Wenn Flüssigkeit auf dem Drucker verschüttet wurde.
C. Wenn der Drucker im Regen gestanden hat oder Wasser darauf verschüttet wurde.
D. Wenn der Drucker trotz genauer Befolgung der Betriebsvorschriften nicht richtig arbeitet. Nur die
in der Bedienungsanleitung angegebenen Einstellungen vornehmen. Ein Verstellen anderer
Bedienungselemente könnte den Drucker beschädigen und macht umständliche Arbeiten eines
qualifizierten Technikers erforderlich, um den Drucker Wieder auf den normalen Betrieb
einzustellen.
E. Wenn der Drucker heruntergefallen ist oder das Gehäuse beschädigt wurde.
F. Wenn der Drucker in seiner Leistung nachläßt.
•Bitte halten Sie den Kunststoffbeutel, in den die Ware verpackt ist, von Kindern entfernt, oder werfen Sie
ihn weg, damit er nicht in die Hande von Kindern gerät. Das Überstülpen des Beutels kann zum
Ersticken führen.
Lärmemission kleiner 70dBA
iDP-3410 User’s Manual
IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A computing device
pursuant to Subpart J of Part 15 off FCC Rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference, in which case the user at his own expense will be required to take
whatever measures may be necessary to correct the interference.
CAUTION: Use shielded cable for this equipment.
Sicherheitshinweis
Die Steckdose zum Anschluß dieses Druckers muß nahe dem Grät angebracht und leicht zugänglich sein.
For Uses in Canada
This digital apparatus does not exceed the class A limits for radio noise emissions from digital, apparatus,
as set out in the radio interference regulations of the Canadian department of communications.
Pour L’utilisateurs Canadiens
Cet appareil numérique ne dépasse pas les limites de carégorie a pour les émissions de bruit radio émanant
d’appareils numériques, tel que prévu dans les réglements sur l’interférence radio du départment Canadien
des communications.
<CAUTIONS>
1. Prior to using the equipment, be sure to read this User's Manual thoroughly. Please keep it handy for reference
whenever it may be needed.
2. The information contained herein may be changed without prior notice.
3. Reproduction of part or all of this User's Manual without permission is strictly prohibited.
4. Never service, disassemble, or repair parts that are not mentioned in this User's Manual.
5. Note that we will not be responsible for damages attributable to a user's incorrect operation/ handling or an
improper operating environment.
6. Operate the equipment only as described in this User's Manual; otherwise accidents or problems may result.
7. Data are basically temporary; they cannot be stored or saved permanently or for a long time. Please note that we
will not be responsible for damages or losses of profit resulting from losses of the data attributable to accidents,
repairs, tests, and so on.
8. If you have any questions or notice any clerical errors or omissions regarding the information in this manual,
please contact our office.
9. Please note that, notwithstanding Item 8 above, we will not be responsible for any effects resulting from
operation of the equipment.
iDP-3410 User’s Manual
iDP-3410 User’s Manual
SAFETY PRECAUTIONS ----- BE SURE TO OBSERVE
In order to prevent hazards to an operator or other persons and damage to property, be sure to observe the following
precautions.
_ The following describes the degrees of hazard and damages that can occur if the given instructions are
neglected or the equipment is incorrectly operated.
WARNING
Negligence of this precaution may result in death or serious injury.
CAUTION
Negligence of this precaution may result in injury or damage to property.
This is an illustration mark used to alert your attention.
This is an illustration mark used to indicate such information as an instruction or the like.
iDP-3410 User’s Manual
WARNING !
_ Never handle the equipment in the following manners, as it may break, become out of order, or overheat
causing smoke and resulting in fire or electric shock.
If the equipment is used in an abnormal condition, such as when broken, then problems, smoke
emission, abnormal odor/noise, and fire can result. If an abnormal condition exists, be sure to turn off
the power, disconnect the power plug from a plug socket, and contact our dealer. Never repair the
equipment on your own - it is very dangerous.
• Do not allow the equipment to receive a strong impact or shock, such as kicking, stomping, hitting,
dropping, and the like.
• Install the equipment in a well-ventilated place. Do not use it in such a manner that its ventilation port
will be blocked.
• Do not install the equipment in a place like a laboratory where chemical reactions are expected, or in a
place where salt or gases are contained in the air.
• Do not connect/disconnect a power cord or a data cable, while holding the cable. Do not pull, install,
use, or carry the equipment in such a manner that force will be applied to the cables.
• Do not drop or insert any foreign substances, such as clips or pins, into the equipment.
• Do not spill any liquid or spray any chemical-containing liquid over the equipment. If any liquid is
spilled on it, turn off the power, disconnect the power cable and power cord from the plug socket, and
so on, and contact our dealer.
• Do not disassemble or remodel the equipment. Negligence of this may cause fire or electric shock.
• Should you drop or break this AC adapter by any chance, unplug it immediately and contact our office.
Using it in that condition may result in fire or electric shock.
• Should water enter inside the equipment by any chance, unplug it and contact our office. Using it in
that condition may result in fire or electric shock.
• Use the equipment only with the specified commercial power supply. Negligence of this may result in
fire, electric shock, or problems.
• Do not damage, break, process, bend/pull by force, twist, or bundle an AC adapter cord. Also, do not
put a heavy substance on it or heat it. The AC adapter could be broken, resulting in fire, electric shock,
or trouble. If the AC adapter cord is damaged, contact our office.
• Do not connect/disconnect the AC adapter with wet hands. It may result in electric shock or other
problems.
• Do not overload a single electrical outlet, using a table tap or a current tap socket. It may result in fire
or electric shock.
_ An equipment packing bag must be discarded or kept away from children. A child can suffocate if the
bag is placed over the head.
iDP-3410 User’s Manual
PRECAUTIONS FOR INSTALLATION
• Do not use or store the equipment in a place exposed to fire, moisture, or direct sunlight, or in a place
near a heater or a thermal device where the prescribed operating temperature and humidity are not met,
or in a place exposed to much oil, iron powder, or dust. The equipment may become out of order, emit
smoke, or catch fire.
• Do not install the equipment in a place like a laboratory where chemical reactions are expected, or in a
place where salt or gases are contained in the air. There is a danger of fire or electric shock.
• Do not put any object on the printer. It may cause trouble.
• Do not use the equipment near a radio or TV receiver. Do not share the power from a plug socket a
radio or TV receiver is connected to. It may cause a reception problem.
• Use the equipment only at the specified voltage and frequency. Otherwise, it may emit smoke and catch
fire or cause other problems.
• Confirm that a plug socket used for connection has sufficient capacity.
• Do not overload a single electrical outlet in connecting the power cable. It may result in the cable
catching fire or a power outage. Also, do not stamp or put any object on the cable.
• Never connect a grounding cable to a gas pipe. There is a danger of explosion. When connecting or
disconnecting the grounding cable, be sure to disconnect the power plug from the plug socket.
• When connecting/disconnecting the cables, be sure to turn off the power first, including the connected
side, and then connect/disconnect them, holding a plug and a connector. Do not pull or carry the
equipment with a load applied to the cable.
• Connect a connector cable securely. If a reverse-polarity connection is made, internal elements may be
broken or a mating device may be adversely affected.
• Use a shielding wire or twisted pair wire for a signal line, in order to minimize noise effect. Avoid
connecting to a device that is likely to generate noise.
• When a drawer kick connector is provided, do not connect any device other than the prescribed solenoid
specifications. Negligence of this could cause trouble.
• Use the equipment in an environment where there is a plug socket near the main body and you can
easily disconnect the power plug from it, to shut off the power.
• When the equipment will not be used for a long period of time, unplug it.
• When transporting the equipment, remove the rolled paper from it.
• Install the equipment on a flat, stable desk in a well-ventilated place free from vibrations. (Do not block
the ventilation port.)
iDP-3410 User’s Manual
PRECAUTIONS FOR HANDLING
Do not handle the equipment in the following manners, because problems may result.
• Do not use a power supply other than the specified AC adapter.
• Do not print when there is no recording paper or ink ribbon set in the equipment. The print head may be
damaged
• Be careful not to drop foreign substances, such as clips, pins, and screws, into the main body.
• Do not spill any liquid or spray any chemical-containing liquid over the equipment.
• Do not stamp on, drop, hit, or give a strong shock to the equipment.
• Never use a pointed object, such as a pen, to operate the operation panel.
• Do not use Scotch tape to fasten paper together for continuous use.
• Never pull the set paper forcibly. When opening/closing the printer cover, take care that the paper will
not be caught.
To Prevent Injury and Spreading of Damage
• Do not touch the printing part of the print head.
• When turning on the power, do not touch the moving parts, such as a cutter and gear inside the main
body, or electric parts.
• Be careful to avoid bodily injure or damaging other objects with an edge of sheet metal.
• Should any error occur while operating the equipment, stop it immediately and disconnect the power
plug from the plug socket.
• Should a problem occur, leave solving it to our serviceman. Do not disassemble the equipment on your
own.
• When opening/closing the cover, and so on, be careful not to catch your hand or finger on the
equipment.
iDP-3410 User’s Manual
DAILY MAINTENANCE
• Prior to starting maintenance work, be sure to turn off the main body.
• Use a dry soft cloth to wipe off stains and dust from the surfaces of the main body case. For severe
soiling, dip the cloth in water and wring it, for wiping off the soil. Never use organic solvents, such as
alcohol, thinner, trichlene, benzene, ketone, or chemical dusters.
• If the equipment is contaminated with paper powder, use a soft brush to clean it.
iDP-3410 User’s Manual
CONTENTS
1. OUTLINE........................................................................................................................................................ 16
1.1
Features................................................................................................................................................................ 16
1.2
Unpacking............................................................................................................................................................ 16
2. BASIC SPECIFICATIONS ............................................................................................................................. 17
2.1
Model Classifications .......................................................................................................................................... 17
2.2
Basic Specifications............................................................................................................................................. 18
2.3
Paper Specifications ............................................................................................................................................ 19
2.3.1
Recommended Paper................................................................................................................................ 19
2.3.2
Printing Position....................................................................................................................................... 19
2.3.3 Cutter Layout...................................................................................................................................................... 19
3. OUTER APPEARANCE AND COMPONENT PARTS................................................................................... 20
4. OPERATION .................................................................................................................................................. 21
4.1
Connecting AC Adapter ...................................................................................................................................... 21
4.2
Connecting Interface Cable ................................................................................................................................. 22
4.3
Connecting Drawer Kick-Out Connector............................................................................................................ 22
4.4
Setting the Cassette Ribbon................................................................................................................................. 23
4.5
Inserting the Paper............................................................................................................................................... 24
4.6
How to Remove Remaining Paper Roll .............................................................................................................. 26
4.7
Removing Paper Jam........................................................................................................................................... 26
4.8
Operation Panel and Display of Error ................................................................................................................. 27
4.9
Operation Flow at Power-on ............................................................................................................................... 28
5. DIP SWITCH SETTING ................................................................................................................................. 29
5.1
Location of DIP Switch ....................................................................................................................................... 29
5.2
DIP Switches Setting........................................................................................................................................... 30
6. PRESET JUMPER SETTING.......................................................................................................................... 32
6.1
Location of Preset Jumper ................................................................................................................................... 32
6.2
Preset Jumper Table ............................................................................................................................................ 32
7. MODE SETTING METHOD .......................................................................................................................... 33
8. INPUT BUFFER BACKUP FUNCTION ........................................................................................................ 34
8.1
Buffer Size........................................................................................................................................................... 34
8.2
Input Buffer Backup ............................................................................................................................................ 34
8.3
Clearing the Input Buffer..................................................................................................................................... 34
9. PARALLEL INTERFACE .............................................................................................................................. 35
9.1
Specifications ...................................................................................................................................................... 35
9.2
Connector's Pin Configuration ............................................................................................................................ 35
9.3
Input and Output Signals ..................................................................................................................................... 36
9.3.1
Input and Output Signals.......................................................................................................................... 36
9.3.2
Electrical Characteristics.......................................................................................................................... 37
9.3.3
Timing Chart ............................................................................................................................................ 38
9.3.4
Data Receiving Control............................................................................................................................ 38
10. SERIAL INTERFACE................................................................................................................................... 39
10.1 Specifications ...................................................................................................................................................... 39
10.2 Connector's Pin Configuration ............................................................................................................................ 40
iDP-3410 User’s Manual
10.3
Input and Output Signals ..................................................................................................................................... 41
10.3.1 Input and Output Signals.......................................................................................................................... 41
10.3.2 Data Configuration................................................................................................................................... 43
10.3.3 Error Detection......................................................................................................................................... 44
10.3.4 Data Receiving Control............................................................................................................................ 44
10.3.5 Buffering .................................................................................................................................................. 44
10.3.6 Electrical Characteristics.......................................................................................................................... 45
11. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR........................................................... 46
11.1 Specifications of Drawer Kick-Out Connector ................................................................................................... 46
11.2 Connector's Pin Configuration ............................................................................................................................ 46
11.3 Drive Circuit........................................................................................................................................................ 46
11.4 Specifications of Power Supply Connector......................................................................................................... 47
12. MAINTENANCE AND SERVICE ................................................................................................................ 48
13 PRINT CONTROL FUNCTIONS .................................................................................................................. 49
13.1 CBM Mode.......................................................................................................................................................... 49
13.1.1 Command List.......................................................................................................................................... 49
13.1.2 Description of Items ................................................................................................................................ 50
13.2 STAR Mode........................................................................................................................................................ 68
13.2.1 Command List.......................................................................................................................................... 68
13.3 ESC/POS Mode ................................................................................................................................................... 99
13.3.1 Command List.......................................................................................................................................... 99
14. CHARACTER CODES TABLE................................................................................................................... 121
14.1 CBM (Domestic) ............................................................................................................................................... 121
14.2 CBM (International) .......................................................................................................................................... 122
14.3 STAR (Domestic).............................................................................................................................................. 123
14.4 STAR (International)......................................................................................................................................... 124
14.5 Code Page 437................................................................................................................................................... 125
14.6 Katakana ............................................................................................................................................................ 126
14.7 Code Page 850................................................................................................................................................... 127
14.8 Code Page 860................................................................................................................................................... 128
14.9 Code Page 863................................................................................................................................................... 129
14.10 Code Page 865................................................................................................................................................... 130
14.11 Code Page 852................................................................................................................................................... 131
14.12 Code Page 866................................................................................................................................................... 132
14.13 Code Page 857................................................................................................................................................... 133
14.14 Windows Code .................................................................................................................................................. 134
14.15 International Character Codes Table ................................................................................................................. 135
APPENDIX 1.
APPENDIX 2.
BLOCK DIAGRAM .............................................................................................................. 136
OUTLINE DRAWING ........................................................................................................... 137
iDP-3410 User’s Manual
<<< German >>>
4. BETRIEB...................................................................................................................................................... 145
4.1
Anschluß des Netzteils ...................................................................................................................................... 145
4.2
Anschluß des Schnittstellenkabels..................................................................................................................... 146
4.3
Anschluß des Ausschubmechanismussteckers der Geldschublade ................................................................... 146
4.4
Einsetzen der Farbbandkassette......................................................................................................................... 147
4.5
Einlegen der Papierrolle .................................................................................................................................... 148
4.6
Entfernen des restlichen Druckpapiers.............................................................................................................. 150
4.7
Beseitigung von Papierstaus.............................................................................................................................. 150
4.8
Bedienfeld und Fehleranzeigelämpchen............................................................................................................ 151
4.9
Betriebsfluß beim Einschalten........................................................................................................................... 152
5. DIP SCHALTER-EINSTELLUNG................................................................................................................ 153
5.1
Lage der DIP-Schalter ....................................................................................................................................... 153
5.2
DIP-Schalter-Einstellungen............................................................................................................................... 154
6. EINSTELLUNG DER VORWAHL-JUMPERSTECKER.............................................................................. 156
6.1
Lage der Vorwahl-Jumperstecker...................................................................................................................... 156
6.2
Vorwahl-Jumperstecker-Tabelle........................................................................................................................ 156
7. METHODE FÜR MODUSEINSTELLUNG.................................................................................................. 157
12. WARTUNG UND DIENST.......................................................................................................................... 158
Note:
Citizen, Citizen logo are registered trademark of Citizen Watch Co., Ltd.
ESC/POS and EPSON are a trademark and registered trademark of SEIKO EPSON Corporation.
STAR is a registered trademark of Star Micronics Corporation.
Windows
is
a
registered
trademark
of
Microsoft
Corporation.
iDP-3410 User’s Manual
1. OUTLINE
This is a small-size dot impact printer developed for various data communication terminals, POS terminals,
kitchen-use printers, bank card, terminals, and so on.
Its abundant built-in features allow you to widely use this printer for different applications. Prior to using it,
read and understand this manual thoroughly.
1.1
(1)
(2)
(3)
(4)
(5)
(6)
1.2
Features
Small size, light weight, and low price
High-speed print (Bi-directional)
Red and black print
Very easy paper loading by the auto loading function
Paper end detecting function
Power supply through an AC adapter
Unpacking
(1) When unpacking the printer, confirm that the following parts are provided.
•Printer body
----- 1 unit
•Cassette ribbon
----- 1 piece
•Sample paper roll
----- 1 roll
•AC adapter
----- 1 piece
•User's manual
----- 1 copy
CAUTION : • Install the printer on a flat and stable desk.
• Do not install the printer near a heater or in a place exposed to direct sunlight.
• Do not use the printer in a high-temperature, high-humidity, and contaminated
environment.
• Do not allow dew condensation on the printer. If dew is condensed on it, leave the
power turned off until dew condensation is gone.
2. BASIC SPECIFICATIONS
2.1
Model Classification
The printer model is classified by the following designation method.
iDP 3410 - R F 120
Model Name
AC adapter
120: For 120 V AC
230: For 230 V AC
iDP-3410 User’s Manual
Character Set
F: International
Interface
CBM Mode
R: Serial(RS-232C D-Sub)
P: Parallel(CENTRONICS-based)
STAR Mode
S: Serial(RS-232C mini DIN)
C: Parallel(CENTRONICS-based)
ESC/POS Mode
T: Serial(RS-232C D-Sub)
I: Parallel(CENTRONICS-based)
hExclusive AC Adapter Types and Power Cords
•34AD-U (120 V 2-core cord)
•34AD-E
(230
V
2-core
cord)
iDP-3410 User’s Manual
2.2 Basic Specifications
Model
iDP-3410-*F120
Item
Printer mechanism
Print method
Print width
Print head
Print speed
Print columns
Character size
Character types
Line spacing
Paper
Ink ribbon
Interface
Command system
Print function
Input buffer
Buffer backup
Drawer
Auto loading
Paper end detection
Supply voltage
iDP-3410-*F230
DP-410 Series (CITIZEN)
Serial dot impact method (Bi-directional print)
64 mm
9 pins
Approx. 3 lines/sec. (At single-color continuous print)
40 columns or 42 columns (Selectable with the DIP switch)
1.31 mm (W)×3.1 mm (H)
Alphanumeric, International characters, Code page 850, 860, 863, 865, 852, 866,
857; Windows code
4.23 mm(1/6 inch) or 2.82(1/9 inch);
Minimum paper feed pitch 1.41 mm(1/18 inch)
Ordinary paper and non-carbon paper 76+/-0.5 mm (W)×φ83 mm (O.D.);
Single-sheet paper: 45 to 55 kg/1,000 sheets/1,091×788 mm
Copying paper: Non-carbon paper, 1 original + 1 copy, Total thickness 0.2 mm or
less
Special purpose ribbon cartridge, Red/black or single color(black)
Serial (RS-232C), Parallel (CENTRONICS compliant)
CBM mode, STAR mode, ESC/POS mode
The user can select the mode with the DIP switches and preset jumpers.
Provided by operating the on-line, self-test, hex dump print function power
switches and FEED switch
6 KB or 256 bytes (Selectable with the DIP switch)
Within 24 hours (After 10 minutes or more of printer operation)
2-drawer or 1-drawer switch
Equipped (Automatically feeds the paper by several lines when it is inserted.)
Equipped (Stops printing when the paper runs out.)
120 V AC +/- 10 %,
230 V AC +/- 10 %,
50/60 Hz
50/60 Hz
AC adapter
34AD-U
34AD-E
Output: 26 V DC, 1.15 A
Power consumption
Not printing: Approx. 8 W Printing: Approx. 30 W
Weight
Main body: 1.25 kg AC adapter: 0.95 kg
Outer dimensions
144 (W) × 233 (D) × 121 (H) mm
Operating temperature and 0∼40 °C, 35∼85 % RH (No dew condensation)
humidity
Storage temperature and -20∼60°C, 10∼90 % RH (No dew condensation)
humidity
Reliability
Print head: 80,000,000 characters
Mechanism: MCBF 2,500,000 lines
EMI standard
EN55022 Class-A
FCCA
CE Marking
Safety Standard *1
TUV GS
*1.The AC adapter alone has acquired the Electric Appliances Control Act, UL Standard, C-UL
Standard, and TUV
GS Standard.
iDP-3410 User’s Manual
2.3 Paper Specification
2.3.1 Recommended Paper
•Type
: Normal paper and non-carbon paper
•Paper width
: 76 +/- 0.5 mm
•Paper thickness
: Single-sheet paper --- 45∼55 kg / 1,000 sheets / 1,091 x 788 mm; Copying paper
--Non-carbon paper, 1 original + 1 copy,
Total thickness 0.2 mm or less
•Roll diameter
: φ83 mm or less
•Core
: φ12 mm (Inner Diameter), φ18 mm (Outer Diameter)
Printing Position
2.3.3
Cutter Layout
Cutting Position
Approx. 20 mm
2.3.2
iDP-3410 User’s Manual
3. OUTER APPEARANCE AND COMPONENT PARTS
4. OPERATION
4.1
Connecting AC Adapter
iDP-3410 User’s Manual
(1)Turn off the Power switch.
(2) Connect the cable connector of the AC adapter to the power connector located on the back of
the printer.
(3) In order to prevent disconnection of the cable connector, put it through a wire saddle, as shown in the
figure below.
(4) Connect the AC power cord plug to a plug socket.
CAUTION : • Use only the specified AC adapter.
• Use a different AC power supply from one used for any noise-generating device.
• Do not use the accessory AC adapter for another device or application besides this
equipment.
• When disconnecting the AC adapter, be sure to hold the AC adapter itself or the
plug. Do not pull its cord.
• Pulling an AC adapter cord will damage it and may result in fire, electric shock, or
snapping of the wire.
• If lightning is occurring in the area, disconnect the AC adapter from the plug socket
and do not use the equipment. A lightning strike could result in fire or electric
shock.
• Do not put the AC adapter cord near any thermal device. The coating of the power
cord can melt, resulting in fire or electric shock.
• When the printer is not used for a long period of time, be sure to disconnect the AC
adapter from the plug socket, for safety.
iDP-3410 User’s Manual
4.2
Connecting Interface Cable
(1) Turn off the power. (Mating side included)
(2) Check the top and bottom of the cable terminals, and connect to the interface connector.
(3) Fix the cable terminals.
•Serial Interface: Tighten screws, to fix.
•Parallel Interface: Turn a stopper, to fix.
(4)Connect the cable to a computer.
4.3
Connecting Drawer Kick-Out Connector
(1) Turn off the power.
(2) Check the top and bottom of the drawer kick-out cable connector, and connect it to the drawer kick-out
connector located on the back of the printer.
(3) Screw the grounding cable of the drawer to the grounding terminal of the printer.
CAUTION : Connect only the prescribed drawer (Solenoid) to the drawer kick-out
connector.
iDP-3410 User’s Manual
4.4
Setting the Cassette Ribbon
(1) Open the printer cover.
(2) If the ribbon is slackened, turn the knob in the arrow-indicated direction to give the tension to it before
setting.
(3) While putting the ribbon in between the head cover and platen, push the locking claws into the holder of
the printer.
(4) Turn the knob of the cassette ribbon in the arrow-indicated direction to eliminate slackness of the ribbon.
(5) To remove the cassette ribbon, lift it while tilting the locking claws on both sides toward the inside.
iDP-3410 User’s Manual
4.5
Inserting the Paper
(1) Put your hands in the concave parts on both sides of the printer cover, and open it until it comes to a stop.
(2) Cut the end of the paper roll at close to a right angle.
CAUTION : • Be sure to use the specified paper roll.
• Use of unspecified paper may adversely affect print quality, printer service life, and
so on.
• The printer cover is not detachable. Do not apply an excessive force beyond its
stopping position.
• Do not insert a frayed or bent end of paper into the printer.
(3) Check the winding direction of the paper roll.
(4) Opening the paper holder, support the center of the paper roll correctly.
(5) Turn on the printer.
(6) Insert the end of the paper roll straight into the paper inlet slot (Indicated by an arrow on the case).
(7) The paper is automatically fed in and comes out of the paper outlet slot of the printer.
(8) Close the printer cover and cut the surplus paper with a tear bar.
iDP-3410 User’s Manual
CAUTION : • If the paper is slack, rewind it, to remove the slack.
• If the paper is set slantwise, operate the paper-free lever, to correct the paper
position.
• While printing, do not hold the paper. This can cause a paper jam.
iDP-3410 User’s Manual
4.6
How to Remove Remaining Paper Roll
(1) Open the printer cover.
(2) Pushing the paper-free lever in the arrow direction, pull out the paper roll.
CAUTION : When pulling out the paper (Forward/Reverse direction), be sure to operate the paperfree lever.
4.7
Removing Paper Jam
(1) Open the printer cover.
(2) Cut off the paper near the paper inlet slot.
(3) Push the paper-free lever in the arrow direction. The paper feed roller is disengaged, to free the paper,
allowing you to eliminate the jammed paper.
(4) Eliminate completely the paper remaining in the paper route.
CAUTION : • When pulling out the paper (Forward/Reverse direction), be sure to operate the
paper-free lever.
iDP-3410 User’s Manual
4.8
Operation Panel and Display of Error
(1) POWER lamp(Green)
Illuminated when the power is turned on.
(2) ERROR lamp(Red)
Illuminated when the printer is out of paper or has a printer mechanical error or communication error.
<Details of Errors>
•Paper end -----
If the paper runs out, the paper sensor located in the paper course near the print head
detects a paper end, turning on the ERROR LED, thus stopping the printer. If the
paper is inserted into the paper course, it is loaded.
•Printer mechanism error ----If the printer mechanism is abnormally loaded due to a paper jam,
etc., the ERROR LED is illuminated, to stop the printer.
(3) FEED switch
The paper is fed by one line by pressing this switch for a short time, and it is fed continuously by holding
down the switch.
(4) FEED switch and Power switch
Self-print is performed by turning on the Power switch while pressing the FEED switch.
Power-on
iDP-3410 User’s Manual
4.9
Operation Flow at Power-on
Feed SW ?
Buffer data
No
1 Sec. Passed
Yes
"Clear Data in Buffer"
Yes(FEED SW) and Enlarged
Red Print
No
1 Sec. Passed
No
Yes
Off
Off
FEED SW ?
(CONTINUE)
On
Prints" =HexadecimalDump =
Dump Mode
On
Input Buffer Clear
Test Print
Buffer Data
No
Yes
Prints "Power Down(Data in
Buffer)" in Red, Followed by
Buffer Contents.
Waits for Data Input
FEED SW ?
(AGAIN)
Yes
iDP-3410 User’s Manual
5. DIP SWITCH SETTING
5.1
Location of DIP Switch
(1) Turn off the power.
(2) Remove a cassette ribbon. The DIP switches are located as shown in the figure below.
(Only DS1 provided for the parallel interface)
iDP-3410 User’s Manual
5.2
DIP Switches Setting
1) DIP Switch 1
No.
Function
DS1-1
Auto cutter
International characters
DS1-2
″
DS1-3
″
DS1-4
DS1-5
Paper used
DS1-6
CR mode
DS1-7
Number of columns
DS1-8
Buffer size
DS1-9
Operation mode
″
DS1-10
*1, *3 : Depends on the type.
*2
: Depends on the destination.
International Character Selection
No.
DS1-2
DS1-3
Country
ON
Yes
OFF
No
See the Table below
2P
1P
See the Table below
42
40
6K bytes
256 bytes
See the table below
DS1-4
U.S.A.
ON
ON
ON
France
Germany
U.K.
Denmark
Sweden
Italy
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
Japan
OFF
OFF
OFF
Upon Shipment from Factory
OFF
ON *2
ON *2
ON *2
OFF
OFF
ON
ON
OFF *3
OFF *3
Character Code Selection
ESC/POS
CBM mode
mode
CBM
Code 437 (International)
Code 850
Code 850
″
″
″
″
″
″
″
″
″
″
CBM
Katakana
(Domestic)
See the International Character Codes Table and Character Codes Table.
CR mode(DS1-6)
Mode
OFF
CBM
CR+LF
STAR
CR+LF
ESC/POS
CR+LF
ON
CR
Ignored
CR
Operation Mode DS1-9 DS1-10
CBM
OFF
OFF
ESC/POS
ON
OFF
STAR
OFF
ON
STAR
ON
ON
Star mode
Star
(International)
Code 850
″
″
″
″
″
Star
(Domestic)
iDP-3410 User’s Manual
2) DIP Switch 2
No.
Function
DS2-1
Bit length
DS2-2
Parity
DS2-3
Odd/Even
DS2-4
Communication mode
DS2-5
Baud rate
″
DS2-6
″
DS2-7
DS2-8
Unused
ON
8 bits
No
Odd
DTR/DSR
OFF
7 bits
Yes
Even
XON/XOFF
See the table below
−
−
Factory Setting
ON
ON
ON
ON
ON
ON
OFF
OFF
Baud rate
Baud rate(bps)
150
300
600
1200
2400
4800
9600
19200
DS2-5
OFF
OFF
OFF
OFF
ON
ON
ON
ON
DS2-6
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DS2-7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
hThe DIP switch 2 is used only for the serial interface.
(Note) Setting of the paper used simply changes the drive pulse width to the printing head; it does not
mean that 2 ply paper is not available for the 1 ply setting. The same applies to when 1 ply paper
is used for the 2 ply setting.
iDP-3410 User’s Manual
6. PRESET JUMPER SETTING
6.1
Location of Preset Jumper
(1) Turn off the power.
(2) Remove a cassette ribbon.
(3) Remove the top cover. The preset jumper is located as shown in the figure below.
Serial Interface
6.2
Parallel Interface
Preset Jumper Table
Serial Interface
Mode
Location
SCA
SCB
SCC
SCD
SCE
SCF
SCG
SCH
* = Open
1-C * = 1-C or open
2-C * = 2-C or open
CBM
STAR
ESC/POS
1-C *
1-C *
1-C
1-C
1-C *
1-C *
1-C *
1-C
2-C
1-C *
2-C
2-C
2-C
2-C
2-C
2-C *
2-C
2-C
*
*
1-C *
1-C *
1-C *
2-C *
CBM
STAR
ESC/POS
1-C *
1-C
1-C *
1-C
1-C
1-C
1-C *
1-C
2-C *
2-C
2-C
2-C *
Parallel
Mode
Location
SCA
SCB
SCC
SCD
* = Open
1-C * = 1-C or open
2-C * = 2-C or open
7. MODE SETTING METHOD
This printer has the CBM, STAR, and ESC/POS mode. Any desired mode can be selected and set according
to your need.
(1) Setting method
• See 5. DIP SWITCH SETTING.
• Seeing the settings of the DIP switch 1-9 and 1-10 and those of the preset jumper, set each mode.
iDP-3410 User’s Manual
8. INPUT BUFFER BACKUP FUNCTION
8.1
Buffer Size
With the DIP switch, you can set either 6K bytes or 256 bytes.
DIP switch 1-8
ON → 6K bytes
OFF → 256 bytes
8.2
Input Buffer Backup
Even if the power is turned off or fails during the printing process, the data in the input buffer will be saved.
If the power is turned on again, the printer will print a power failure mark, "==POWER DOWN==," in red
and reprints the data from the beginning of the line where it left off.
8.3
Clearing the Input Buffer
When you want to clear the data in the input buffer, turn on the power, holding down the LF switch. A buzzer
will sound to inform you that the input buffer has been cleared. Hold down the LF switch until the buzzer
sounds.
If the printer prints the data erroneously at power-on, clear the input buffer as described above, and
then, re-input the data.
iDP-3410 User’s Manual
9. PARALLEL INTERFACE
9.1
9.2
Specifications
•Data input system
•Control signals
•Applicable connectors
: 8-bit parallel system (DATA1 to DATA8)
: ACK, BUSY, STB, FAULT, SELECT, RESET, COMPULSION
: Printer side --- 57LE-40360 (Equivalent to anphenol),
Cable side
--- 57-30360 (Ditto)
Connector's Pin Configuration
Mode
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CBM
STB
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
ACK
BUSY
PE(HI-LEVEL)
SELECT
GND
GND
GND
FRAME GND
Vcc
STAR
←
←
←
←
←
←
←
←
←
←
←
←
←
←
NC
NC
←
←
Mode
ESC/POS No.
←
19
←
20
←
21
←
22
←
23
←
24
←
25
←
26
←
27
←
28
←
29
←
30
←
31
←
32
←
33
←
34
←
35
NC
36
CBM
STAR
ESC/POS
TWISTED PAIR GND
↑
↑
↑
↑
↑
↑
↑
↑
↑
↑
↑
RESET
FAULT
NC
COMPULSION
NC
Vcc
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
GND
←
←
Vcc
NC
iDP-3410 User’s Manual
9.3
Input and Output Signals
9.3.1 Input and Output Signals
(1) Input signals to the printer
• DATA
: An 8-bit parallel signal. (Positive logic)
• STB
: A strobe signal to read the 8-bit data. (Negative logic)
• RESET
: A signal to reset the printer from the outside.(Negative logic)
(2) Output signals from the printer
• ACK
: An 8-bit data request signal. A pulse signal output at the end of the BUSY signal.
(Negative logic)
• BUSY
: A signal to indicate the BUSY status of the printer. Input new data when at "LOW".
(Positive logic)
• FAULT
: A signal turned to "LOW" when the printer has an alarm. At this time, all the control
circuits in the printer stop. (Negative logic)
• SELECT
: A signal to show whether the printer is selected(on-line) or deselected.(Positive
logic)
• COMPULSION
: A signal to show the status of the drawer switch.(Positive logic)
• PE:
A signal to show that the paper has run out. Normal at the "LOW" level, but turned to
the "HIGH" level when the paper has run out.
(3) Power related signal
• GND
: Common ground on the circuits
• Vcc
: A +5V signal. Connected via a 3.3kΩ resistor.
iDP-3410 User’s Manual
9.3.2 Electrical Characteristics
(1) Input signal level
All the input signals are at the TTL level.
"HIGH" level : 2.0 V at minimum
"LOW" level : 0.8 V at maximum
(2) Output signal level
All the output signals are at the TTL level.
"HIGH" level : 2.4 V at minimum
"LOW" level : 0.4 V at maximum
(3) Input and output conditions
All the input signals are pulled up at 3.3 kΩ.
[Printer Side]
[Host Side]
All the output signals are pulled up at 3.3kΩ.
[Printer Side]
[Host Side]
iDP-3410 User’s Manual
9.3.3 Timing Chart
(1) Data input and printing timing
T1, T2, T3
T4
T5
T6
:
:
:
:
0.5 µs MIN
270 ns MAX
2.3 µs TYP
500 ms MIN (At power-on)
9.3.4 Data Receiving Control
When the BUSY signal is at "LOW," the printer can receive the data from the host, but when at "HIGH," it
cannot.
10. SERIAL INTERFACE
10.1 Specifications
(1) Synchronous system: Asynchronous
(2) Baud rate: 150, 300, 600, 1,200, 2,400, 4,800, 9,600, or 19,200 bps (User selectable)
(3) Configuration of one word
•Start bit
: 1 bit
•Data bits
: 7 or 8 bits (User selectable)
•Parity bit
: Odd, even, or none (User selectable)
•Stop bit
: 1 bit or more
iDP-3410 User’s Manual
(4) Signal polarity
RS-232C
•Mark
= Logic "1" (-3 V ∼ -12 V)
•Space
= Logic "0" (+3 V ∼ +12 V)
(5) Received data (RXD signal)
RS-232C
• Mark
= 1
• Space
= 0
(6) Reception control (DTR signal)
RS-232C
•Mark
: Data transfer disabled
•Space
: Data transfer enabled
iDP-3410 User’s Manual
10.2
Connector's Pin Configuration
Mode
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CBM
STAR
ECS/POS
FG
TXD
RXD
←
←
←
←
←
←
←
RTS
GND
←
PE (HI-LEVEL)
FAULT
RCH
DSR
←
GND
FAULT
mTXD
mRXD
DTR
←
←
RESET
Cautions: 1. An RS-232C signal is based on the EIA RS-232C.
2. When the data is not being transferred, the received data should be always maintained as a
mark.
iDP-3410 User’s Manual
10.3 Input and Output Signals
10.3.1 Input and Output Signals
(1) RXD
This is a serial received data signal. When a framing error, overrun error, or parity error occurs, that
data is printed as "?".
(2) DTR
When this signal is Ready, write the data or a command. If written at the time of Busy, an overrun
error results, ignoring the previous data. The data can be written in the input buffer even during
printing. Busy is also issued at the time of power-on, test print, on-line, and reset.
(3) TXD
XON(11H) or XOFF(13H) is sent at XON/XOFF control. XON(11H) is sent every 3 seconds in the
Star mode.
When a command is received, that requests the printer state and printer status, 1-byte corresponding
data is output.
(4) DSR
When this signal is a space, the data is sent from the printer side. Note that if this signal is a mark
when a request to send command is executed, the printer will wait until the signal becomes a space.
(5) FAULT
¬ CBM mode
When this signal is Space, a mechanical error has occurred.
- STAR mode
When this signal is Mark, a mechanical error has occurred.
(6) RESET
A signal to reset the entire printer.(Negative logic)
(7) RTS
This signal is turned to Space when the printer is turned on.
iDP-3410 User’s Manual
(8) RCH
When the printer is ready to receive, this signal is turned to Space. This signal line is the same as DTR.
(9) mTXD
TXD signal for the diode gate.
(10) mRXD
RXD signal for the diode gate.
(11) FG
This is a Frame Ground signal.
(12) GND
This is a common ground on the circuit.
10.3.2 Data Configuration
t
Mark
b0, b1, b2, ........
Space
(1)
(2)
(1) Start Bit
(2) Data Bit (+ Parity Bit)
(3) Stop Bit (1 or More)
(3)
iDP-3410 User’s Manual
(1) Start bit
After a lapse of 1/2 bit from a mark-to-space fall edge, the state is read again, and if it is a space, it is
recognized as the start bit. If it is a mark, it is assumed neither the start bit nor an error, and it is
attempted to detect the start bit again.
(2) Data bit + parity bit
The data bit and parity bit are sampled for 1 bit worth of time from the 1/2 start bit. The then state is
assumed the data for the corresponding bit. A sequence of the bits are named Bit 0, Bit 1, ..., parity bit,
starting from the one closest to the start bit.
(3) Stop bit
The stop bit is a mark level of 1 bit or more. If a space is detected in detecting the stop bit, a framing
error results.
10.3.3 Error Detection
A parity error, framing error, and overrun error are detected. When an error is detected, that data is stored
in the buffer as "?".
(1) Framing error
This error results when a space is detected in detecting the stop bit. That data is stored in the buffer as
"?".
(2) Parity error
If a parity check has been specified and an error is detected at the time of parity check, that data is
stored in the buffer as "?".
(3) Overrun error
If an overrun error is detected, that data is stored in the buffer as "?".
10.3.4 Data Receiving Control
When the DTR signal is a space, the data from the host side can be received. When it is a mark, however,
the data cannot be received.
10.3.5 Buffering
The DTR signal and the TXD signal are available as a control signal for data transfer to the input buffer.
iDP-3410 User’s Manual
10.3.6 Electrical Characteristics
(1) RS-232C circuit
Input (RXD, DSR, mRXD)
[Printer Side]
[Host Side]
Output (DTR, TXD, mTXD, RCH, RTS, FAULT)
RXD
Mark=(-8V): Stop bit
Space=(+8V): Start bit
Equivalent MAX232
DTR
Equivalent to MAX232
Mark=(-8V): At Busy
Space=(+8V): At Ready
TXD
Mark=(-8V): 1
Space=(+8V): 0
(2) Others
•RESET
•PE
•GND
•FG
: A signal to reset the entire printer.
: A signal to show that the paper has run out. Normal at the "LOW" level, but turned to
the "HIGH" level when the paper has run out.
: Signal ground
: Frame ground
iDP-3410 User’s Manual
11. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR
11.1 Specifications of Drawer Kick-Out Connector
(1) Drawer kick-out drive signal
Parallel Interface ----- Can be learned at the no. 34 pin of the interface connector
Serial Interface ----- Provided with a command to learn the status in the Star and ESC/POS
modes.
(2) Electrical characteristics
1) Drive voltage: 24 V DC
2) Drive current: 0.8 A at maximum(Within 510 ms)
3) Switch signal: Signal level
"L" = 0 ∼ 0.5 V
"H" = 3 ∼ 5 V
11.2 Connector's Pin Configuration
No.
1
2
3
4
5
6
Signal
FG
DRAWER 1
DRSW
VDR
DRAWER 2
GND
Function
Frame Ground
Drawer 1 drive signal
Drawer switch input
Drawer drive power
Drawer 2 drive signal
Common ground on the circuit
Connector used
Applicable connector
: TM5RJ3-66 (HIROSE)
: TM3P-66P (HIROSE) or equivalent
CAUTION : • No output is made while printing.
• The drawers 1 and 2 cannot be driven simultaneously.
• A solenoid used for the drawer should be of 36Ω or more. An output current should be
kept below 0.8 A. Use beyond this limit cannot be assured.
• This connector cannot be connected to a telephone line. Do not connect other than
the solenoid.
11.3 Drive Circuit
iDP-3410 User’s Manual
11.4 Specifications of Power Supply Connector
This is a power connector from an exclusive AC adapter.
Connector’s Pin Configuration
1
Jack used
Applicable plug
No.
Function
1
2
+24V
GND
2
: HEC0470-01-640(HOSHIDEN) or equivalent
: JXP series Type-A (I.D. 2.45 mm, O.D. 5.5 mm) (HOSHIDEN) or equivalent
CAUTION: • Be sure to use the specified power supply. Use of unspecified one may lead to a
trouble or breakage.
• Do not connect the power supply with different polarities.
iDP-3410 User’s Manual
12. MAINTENANCE AND SERVICE
For the information on maintenance and service, please contact our dealer or at the following address.
Northern America
CBM America Corporation
Service Center
365 Van Ness Way
Suit 510
Torrance, CA 90501, U.S.A
Other Areas
Japan CBM Corporation
Information Systems Division
CBM Bldg., 5-68-10, Nakano
Nakano-ku, Tokyo 164-0001
Japan
TEL +1-310-781-1460
FAX +1-310-781-9157
TEL +81-3-5345-7540
FAX +81-3-5345-7541
13. PRINT CONTROL FUNCTIONS
13.1
CBM Mode
13.1.1 Command List
Command
1 FF n
2 SO
3 SI
4 LF
5 CR
6 DC 1
7 DC 2
8 DC 3
9 CAN
Function
n-line paper feed
Specifying the double width character
Canceling the double width character
Printing and paper feed
Printing
Initializing the printer
Specifying/Canceling the Inverted character
Specifying the red print
Canceling the print data
Code
0CH n
0EH
0FH
0AH
0DH
11H
12H
13H
18H
Page
56
56
57
57
57
58
58
59
59
iDP-3410 User’s Manual
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
ESC ∗ n1 n2
ESC − n
ESC 1
ESC 2
ESC 3
ESC C n
ESC N n
ESC O
ESC f 1
ESC t n
ESC BEL n1 n2
BEL
FS
SUB
RS
ESC R 1
ESC & 0 n1 n2
ESC % n
ESC ⁄ n
ESC DC3 n
30
ESC DC2 n1 n2
31
32
GS ∗ n1 n2
GS ⁄ m
Specifying the bit image mode
1BH 2AH n1 n2
Specifying/Canceling the Underline
1BH 2DH n
Specifying 1/9-inch line feed rate
1BH 31H
Specifying 2/9-inch line feed rate
1BH 32H
Specifying 1/6-inch line feed rate
1BH 33H
Setting the page length
1BH 43H n
Specifying the perforation skip
1BH 4EH n
Canceling the perforation skip
1BH 4FH
Form feed (Changing the page)
1BH 66H 01H
Selecting the character code table
1BH 74H n
Setting the external device drive pulse width
1BH 07H n1 n2
Driving command A for Drawer-1
07H
Driving command B for Drawer-1
1CH
Driving command for Drawer-2
1AH
Buzzer-on
1EH
Selecting the international character set
1BH 52Hn
1BH 26H 00H n1 n2
Defining the download character set
Specifying/Canceling download character set
1BH 25H n
Definition the message
1BH 2FH n
Printing the message
1BH 13H n
Deleting the download character, message, bit
1BH 12H n1 n2
image
Defining the download, bit image
1DH 2AH n1 n2
Printing the download, bit image
1DH 2FH m
60
60
61
61
61
61
62
62
62
63
64
64
65
65
65
66
67
68
68
69
70
71
72
13.1.2 Description of Items
XXXX
ALL
[Function]
Command name
[Code]
A row of command constituent code is represented by a hexadecimal number with < >H,
binary number with < >B, and a decimal number with < >. [ ]k means a repeat count of ktimes.
[Range]
Describes an argument value (Setting range) for the command.
[Outline]
Describes a command function.
[Caution]
Describes a caution as required.
[Default]
Describes an initial value for the command when accompanied by an argument.
iDP-3410 User’s Manual
XXX
Shows a command.
iDP-3410 User’s Manual
Details
FF n
[Function]
n-line paper feed
[Code]
<0C>H n
[Range]
1 ≤ n ≤ 127
[Outline]
This command feeds the paper by n-lines. You can set n = 1 to 127 lines. If the print buffer
contains the data, use of this command feeds the paper by n-lines after printing the data.
Setting n = 0 does not feed the paper.
[Function]
Specifying the double width character
[Code]
<0E>H
[Outline]
The data following this command is printed doubled in the horizontal direction. Double
width characters remain valid until the double width character cancel command is entered,
but they are also cancelled after they are printed one line. Note that the double width
characters take up two ordinary characters worth of width.
SO
iDP-3410 User’s Manual
SI
[Function]
Canceling the double width character
[Code]
<0F>H
[Outline]
This command cancels the double width characters set with SO. The data following this
command are printed in the ordinary character width.
[Function]
Printing and paper feed
[Code]
<0A>H
[Outline]
If the print buffer contains the data, this command will feed the line after printing. If not, the
command only feeds the line.
LF
CR
[Function]
Printing
[Code]
<0D>H
[Outline]
This command prints the data. If the DIP switch segments 1 to 6 are set to OFF, the printer
will print the data in the print buffer and feed the paper by one line. If they are set to ON, the
printer will print the data in the print buffer and will not feed the paper.
DC1
[Function]
Initializing the printer
[Code]
<11>H
[Outline]
This command initializes the printer.
The input buffer is not cleared.
The settings of the DIP switch segments are not re-read.
DC2
[Function]
Specifying/Canceling the inverted character
[Code]
<12>H
[Outline]
This command selects/deselects the inverted characters. Enter this command at the
beginning of one line. Otherwise, it is overridden. Erect and inverted characters cannot be
iDP-3410 User’s Manual
mixed in one line.
iDP-3410 User’s Manual
DC3
[Function]
Specifying the red print
[Code]
<13>H
[Outline]
This command specifies red-color characters. All the characters in one line are printed in red
by prefixing the print data with this command and sending it to the printer. When you want
to use red characters, use this command for each line.
CAN
[Function]
Canceling the print data
[Code]
<18>H
[Outline]
This command clears the print data in the lines entered prior to this command.
iDP-3410 User’s Manual
ESC "∗" n1 n2
[Function]
Specifying the bit image mode
[Code]
<1B>H <2A>H n1 n2
[Range]
1 ≤ n1 + 256 × n2 ≤ 378
[Outline]
This command allows printing in the bit image mode. Divide the number of dots printed by
256 and assume its quotient to be n2 and remainder to be n1. Therefore, the number of
horizontal dots will be n1 + 256 × n2.
If the bit image data is entered beyond the dot positions printable in one line, the surplus data
will be discarded. Normal data processing is restored after bit image printing. Printing is
done in a single direction.
ESC "−" n
[Function]
Specifying/Canceling the underline
[Code]
<1B>H <2D>H n
[Outline]
This command selects/deselects an underline.
deselected at n = 0.
[Default]
n=0
ESC "1"
[Function]
Setting the 1/9-inch line feed width
[Code]
<1B>H <31>H
[Outline]
This command sets the line feed width to 1/9 inch.
ESC "2"
[Function]
Setting the 2/9-inch line feed width
[Code]
<1B>H <32>H
[Outline]
This command sets the line feed width to 2/9 inch.
The underline is selected at n = 1 and
iDP-3410 User’s Manual
ESC "3"
[Function]
Setting the 1/6-inch line feed width
[Code]
<1B>H <33>H
[Outline]
This command sets the line feed width to 1/6 inch(Default).
ESC "C" n
[Function]
Setting the page length
[Code]
<1B>H <43>H n
[Range]
1 ≤ n ≤ 127
[Outline]
Sets the 1-page length to n-lines.
iDP-3410 User’s Manual
ESC "N" n
[Function]
Specifying the perforation skip
[Code]
<1B>H <4E>H n
[Range]
1 ≤ n ≤ 126
[Outline]
This command feeds(Skips) the lines specified with n without printing. However, you cannot
specify beyond the length of one page.
ESC "O"
[Function]
Canceling the perforation skip
[Code]
<1B>H <4F>H
[Outline]
This command cancels perforation skipping operation.
ESC "f" 1
[Function]
Form feed (Changing the page)
[Code]
<1B>H <66>H <01>H
[Outline]
This command searches for the beginning of the next page after printing the data in the print
buffer.
iDP-3410 User’s Manual
ESC "t" n
[Function]
Selecting the character code table
[Code]
<1B>H <74>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects Page-n of Character Code Table.
[Default]
Depends upon DIP switch setting.
n
0
1
2
3
4
5
Character Code Table
CBM International
CBM Domestic
Code Page 850 (Multilingual)
Code Page 860 (Portugal)
Code Page 863 (Canada-French)
Code Page 865 (Norway)
n
6
7
8
9
255
Character Code Table
Code Page 852 (Eastern Europe)
Code Page 866 (Russia)
Code Page 857 (Turkey)
Windows Code
Space Page (For user setting)
iDP-3410 User’s Manual
ESC BEL n1 n2
[Function]
Setting the external device drive pulse width
[Code]
<1B>H <07>H n1 n2
[Range]
1 ≤ n1 ≤ 127
[Outline]
This command sets the power-on time to drive an external device (Cash drawer).
Power-on time = n1 × 10 (ms)
Delay time = n2 × 10 (ms)
To actually drive the drawer, use the <BEL> and <FS> commands.
[Default]
n1 = n2 = 20
1 ≤ n2 ≤ 127
BEL
[Function]
Driving command A for drawer-1
[Code]
<07>H
[Outline]
This command drives the drawer connector no. 2 pin under the condition set with the
<ESC><BEL> n1 n2 command. This command is executed in order of entry into the input
buffer.
iDP-3410 User’s Manual
FS
[Function]
Driving command B drawer-1
[Code]
<1C>H
[Outline]
This command drives the drawer connector No. 2 pin under the condition set with the
<ESC><BEL> n1 n2 command.
SUB
[Function]
Driving command for drawer-2
[Code]
<1A>H
[Outline]
As soon as this command is received, the drawer connector no. 5 pin is driven. The poweron time is 200 ms ON and 200 ms OFF stationary. The drawers 1 and 2 cannot be driven
simultaneously.
[Function]
Buzzer-on
[Code]
<1E>H
[Outline]
This command emits a short warning sound from the printer.
RS
iDP-3410 User’s Manual
ESC "R" n
[Function]
Selecting the international character set
[Code]
<1B>H <52>H n
[Range]
0 ≤ n ≤ 10
[Outline]
This command selects the international characters according to the value of n.
n
Character Set
n
Character Set
0
U.S.A.
6
Italy
1
France
7
Spain
2
Germany
8
Japan
3
U.K.
9
Norway
4
Denmark I
10
Denmark II
5
Sweden
[Default]
Depends upon DIP switch setting.
iDP-3410 User’s Manual
ESC "&" <0> n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1
[Function]
Defining the Download character set
[Code]
<1B>H <26>H <00>H n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1
[Range]
32 ≤ n1 ≤ n2 ≤ 255 m0 = 0 or m0 = 128
[Outline]
This command defines he download characters. n1 is a character code to start definition and
n2 is to end definition, respectively. When defining only one character, set n1 = n2. You can
define the ASCII codes ranging from 32 to 255. Once the download characters are defined,
they remain valid until they are redefined or the download deletion command (ESC DC2 n1
n2) is executed.
iDP-3410 User’s Manual
ESC "%" n
[Function]
Specifying/Canceling the download character set
[Code]
<IB>H <25>H n
[Outline]
This command selects/deselects the download character set. The download characters cannot
be printed by simply defining them with the above-mentioned ESC & 0 command. To print
them, send this command to the printer.
n
0
30
1
31
Download Character Set
Deselects
Selects
ESC "⁄" n "data" CR or LF
[Function]
Defining the Message
[Code]
<1B>H <2F>H n "data" CR or LF
[Range]
1 ≤ n ≤ 10
[Outline]
This command can define up to a 50-byte message in one line. If the value of n is specified
beyond the range, the data following n will be treated as the print data.
Once the message is defined, it remains valid until it is redefined. The data should end with
CR (0DH) or LF (0AH). If the data exceeds 50 bytes, the subsequent data will be treated as
the print data.
Once the message is defined, it remains valid until it is redefined or the download deletion
command (ESC DC2 n1 n2) is executed.
iDP-3410 User’s Manual
ESC DC3 n
[Function]
Printing the message
[Code]
<1B>H <13>H n
[Range]
1 ≤ n ≤ 10
[Function]
This command prints a message. If the value of n is specified beyond the range, the message
will not be printed.
iDP-3410 User’s Manual
ESC DC2 n1 n2
[Function]
Deleting the download character, message, bit image
[Code]
<1B>H <12>H n1 n2
[Range]
0 ≤ n1 ≤ 3
0 ≤ n2
(Specify 0 at n1 = 0)
(1 ≤ n2 ≤ 10 at n1 = 1)
(32 ≤ n2 ≤ 255 at n1 = 2)
(Specify 0 at n1 = 3)
[Outline]
This command deletes the downloaded characters, message, and bit image.
n1
0
1
2
3
Object Deleted
All(Message, characters, bit image)
Download message
Download characters
Download bit image
With n2, specify which data of the function specified with n1 should be deleted.
n2 = 0 Deletes all the data saved with the download function specified with n1.
n2≠0
Deletes the data downloaded at the value specified with n2 (Value specified when
saving with each download command), of the download function specified with n1.
Note) No meaning when n1 = 0 is set.
iDP-3410 User’s Manual
GS "∗" n1 n2 [d] n1 × n2 × 8
[Function]
Defining the download, bit image
[Code]
<1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8
[Range]
1 ≤ n1 ≤ 45 0 ≤ n2 ≤ 24
Note) Take care that the number of data (n1×n2×8) is equal to or smaller than 2,048.
[Outline]
This command defines the download bit image having the dots specified n1 and n2. The
number of horizontal dots is represented by n1 × 8 and that of vertical dots is represented by
n2 × 8, respectively. m denotes the number to be registered. (See a download bit image
printout.) d denotes the bit image data. Once the download bit image is defined, it remains
valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed.
iDP-3410 User’s Manual
GS ⁄ m
[Function]
Printing the download, bit image
[Code]
<1D>H <2F>H m
[Range]
0 ≤ m ≤ 255
[Outline]
This command prints the bit image saved in the number specified with m.
[Caution]
If the print buffer contains the data, this command will be ignored. If the bit image has not
been saved in the specified number, this command will be ignored.
Nothing is printed when m is other than 0,1,2 or 3.
iDP-3410 User’s Manual
13.2
STAR Mode
13.2.1 Command List
Command
1 ESC R n
2 ESC 6
3 ESC 7
4 ESC M
5 ESC P
6 ESC :
7 SO
8 DC4
9 ESC E
10 ESC F
11 ESC −
12 ESC _
13 ESC 4
14 ESC 5
15 SI
16 DC2
17 LF
18 CR
19 ESC z
20 ESC 0
21 ESC a n
22 FF
23 ESC C n
24 ESC C 0 n
25 VT
26 ESC B n1 n2
27 ESC N n
28 ESC 0
29 ESC 1 n
30 ESC Q [n] k NUL
31 HT
32 ESC D n1 n2
33 ESC 1
34 ESC A n
35 ESC 2
36 ESC J n
37 ESC K n1 <0>
38 ESC L n1 n2
39 ESC h n
40 ESC & <0> n1 n2
41 ESC % n
42
43
Command
ESC BEL n1 n2
BEL
Function
Selecting the international character set
NOP
NOP
NOP
NOP
NOP
Specifying the double width character
Canceling the double width character
Specifying the highlight character
Canceling the highlight character
Specifying/Canceling the underline
NOP
Specifying the red print
Canceling the red print
Specifying the inverted character
Canceling the inverted character
Printing and paper feed
Printing
Setting the 1/6-inch line feed
NOP
n-line paper feed
Form feed (Change the page)
Setting the n-line page length
Setting the n-inch page length
Vertical tab
Setting the vertical tab position
Setting the lower margin
Canceling the lower margin
Setting the left margin
Setting the right margin
Horizontal tab
Setting the horizontal tab position
Setting the 1/9-inch line feed width
NOP
Setting the 2/9-inch line feed width
NOP
Specifying the 8-dot standard density bit image
Specifying the 8-dot double density bit image
Page
75
Defining the download character
Specifying/Canceling the download character set
Code
1BH 52H n
1BH 36H
1BH 37H
1BH 4DH
1BH 50H
1BH 3AH
0EH
14H
1BH 45H
1BH 46H
1BH 2DH n
1BH 5FH n
1BH 34H
1BH 35H
0FH
12H
0AH
0DH
1BH 7AH
1BH 30H
1BH 61H n
0CH
1BH 43H n
1BH 43H 00 n
0BH
1BH 42H n1 n2
1BH 4EH n
1BH 4FH
1BH 6cH n
1BH 51H n
09H
1BH 44H n1 n2
1BH 31H
1BH 41H n
1BH 32H
1BH 4AH n
1BH 4BH n1 00H
1BH 4CH n1 n2
1BH 68H n
1BH 26H 00H n1 n2
1BH 25H n
Function
Setting the external device drive pulse width
Driving command A for drawer-1
Code
1BH 07H n1 n2
07H
Page
92
92
Specifying/Canceling the double height character
75
76
76
76
77
77
77
78
78
79
79
79
80
80
80
81
81
82
82
83
83
83
84
85
86
86
87
88
89
90
91
iDP-3410 User’s Manual
44
45
46
47
48
49
FS
SUB
RS
CAN
DC3
DC1
50
ESC U n
51
52
53
54
55
56
57
ESC @
ENQ
STX
ETX
ESC t n
ESC ⁄ n
ESC DC3
58
ESC DC2 n1 n2
59
60
GS ∗ n1 n2
GS ⁄ m
Driving command B for drawer-1
Driving command for drawer-2
Buzzer-on
Canceling the print data
Setting the deselect mode
Setting the Select mode
Selecting the Unidirectional/bidirectional print
mode
Initializing the printer
Enquiry
Text start
Text end command
Selecting the character code table
Defining the message
Printing the message
Deleting the download character, message bit
image
Defining the download, bit image
Printing the download, bit image
1CH
1AH
1EH
18H
13H
11H
93
93
93
94
94
94
1BH 55H n
95
1BH 40H
05H
02H
03H
1BH 74H n
1BH 2FH n
1BH 13H n
1BH 12H n1 n2
95
96
97
97
99
100
100
1DH 2AH n1 n2
1DH 2FH m
102
103
101
iDP-3410 User’s Manual
Details
ESC “R” n
[Function]
Selecting the international character set
[Code]
<1B>H <52>H n
[Range]
0 ≤ n ≤ 10
[Outline]
This command selects the international characters according to the value of n.
n
0
1
2
3
4
5
Character Set
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
n
6
7
8
9
10
Character Set
Italy
Spain
Japan
Norway
Denmark II
[Default]
Depends upon DIP switch setting.
[Function]
Specifying the double width character
[Code]
<0E>H
[Outline]
The data following this command is printed doubled in the horizontal direction. Double
width characters remain valid until the double width character cancel command is entered,
but they are also cancelled after they are printed one line. Note that the double width
characters take up two ordinary characters worth of width.
SO
iDP-3410 User’s Manual
DC4
[Function]
Canceling the double width character
[Code]
<14>H
[Outline]
This command deselects the double width characters set with SO. The data following this
command will be printed in ordinary characters.
ESC "E"
[Function]
Specifying the highlight character
[Code]
<1B>H <45>H
[Outline]
The data following this command is printed in highlight (Double) characters. The highlight
characters remain valid until the highlight character deselection command is entered.
ESC "F"
[Function]
Canceling the highlight character
[Code]
<1B>H <46>H
[Outline]
This command deselects the highlight characters set with ESC "E". The data following this
command will be printed in ordinary characters.
iDP-3410 User’s Manual
ESC "−" n
[Function]
Specifying/Canceling the underline
[Code]
<1B>H <2D>H n
[Outline]
This command selects/deselects an underline. The underline is selected at n = 1 and
deselected at n = 0.
The space by the horizontal tab is not underlined.
ESC "4"
[Function]
Specifying the red print
[Code]
<1B>H <34>H
[Outline]
This command prints its subsequent data in red. This command remains valid until the red
print deselection command is entered. Red and black characters cannot be mixed in one line.
ESC "5"
[Function]
Canceling the red print
[Code]
<1B>H <35>H
[Outline]
This command deselects red print.
iDP-3410 User’s Manual
SI
[Function]
Specifying the inverted character
[Code]
<0F>H
[Outline]
This command selects and prints the inverted characters. Enter it at the beginning of one
line. Otherwise, it will be invalid. Erect and inverted characters cannot be mixed in one line.
DC2
[Function]
Canceling the Inverted character
[Code]
<12>H
[Outline]
This command deselects the inverted characters. Enter this command at the beginning of one
line.
iDP-3410 User’s Manual
LF
[Function]
Printing and paper feed
[Code]
<0A>H
[Outline]
If the print buffer contains the data, this command will feed the line after printing. If not, the
command only feeds the line.
CR
[Function]
Printing
[Code]
<0D>H
[Outline]
This command prints the data. If the DIP switch segments 1 to 6 are set to OFF, the printer
will print the data in the print buffer and feed the paper by one line. If they are set to ON, the
printer will print the data in the print buffer and will not feed the paper.
ESC "z"
[Function]
Setting the 1/6-inch line feed width
[Code]
<1B>H <7A>H
[Outline]
This command sets the line feed width to 1/6 inch (Default).
iDP-3410 User’s Manual
ESC "a" n
[Function]
Setting the n-line paper feed
[Code]
<1B>H <61>H n
[Range]
1 ≤ n ≤ 127
[Outline]
This command feeds the paper by the number of lines specified with n. You can set n = 1 to
127 lines. If the print buffer contains the data, use of this command feeds the paper by nlines after printing the data.
[Function]
Form feed (Changing the page)
[Code]
<0C>H
[Outline]
This command searches for the head of the next page after printing the data in the print
buffer.
FF
ESC "C" n
[Function]
Setting the n-line page length
[Code]
<IB>H <43>H n
[Range]
1 ≤ n ≤ 255
[Outline]
Sets the 1-page length to n-lines.
[Default]
n = 42
ESC "C" <0> n
[Function]
Setting the n-inch page length
[Code]
<1B>H <43>H <0> n
[Range]
1 ≤ n ≤ 127
[Outline]
This command sets the length of one page to n-inches.
[Default]
n = 42
VT
[Function]
Vertical tab
[Code]
<0B> H
iDP-3410 User’s Manual
[Outline]
This command feeds the paper to the next vertical tab position. It cannot be fed unless the
vertical tab position has been set. If the current position is equal to or greater than the
maximum set vertical tab position, it will be fed to the head of the next page.
iDP-3410 User’s Manual
ESC "B" [n]k NUL
[Function]
Setting the vertical tab position
[Code]
<1B>H <42>H [n]k <00>
[Range]
1 ≤ n ≤ 255
1 ≤ k ≤ 16
[Outline]
This command cancels the already set vertical tab positions and sets new vertical tab
positions. They are set in the ascending order and ends with <00>. Up to 16 vertical tabs
can be set. If the tab setting position <nK> is equal or smaller than the preceding set position
<nk-1>, it is assumed that setting of the vertical tabs has been completed.
ESC "N" n
[Function]
Setting the lower margin
[Code]
<1B>H <4E>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command sets the n-line lower margin.
[Default]
n=0
iDP-3410 User’s Manual
ESC "O"
[Function]
Canceling the lower margin
[Code]
<1B>H <4F>H
[Outline]
This command deselects the set lower margin.
ESC "l" n
[Function]
Setting the left margin
[Code]
<1B>H <6C>H n
[Range]
0 ≤ n ≤ (Right margin - 2)
[Outline]
This command sets the left margin and printing starts from the column next to the set margin.
ESC "Q" n
[Function]
Setting the right margin
[Code]
<1B>H <51>Hn
[Range]
2 ≤ n ≤ (Max. print columns)
[Outline]
This command sets the right margin and printing is performed up to n-columns.
iDP-3410 User’s Manual
HT
[Function]
Horizontal tab
[Code]
<09>H
[Outline]
This command moves a printing position to the preset next horizontal tab position. This
command will be ignored unless there is the next horizontal tab position.
iDP-3410 User’s Manual
ESC "D" [n] k NUL
[Function]
Setting the horizontal tab position
[Code]
<1B>H <44>H [n] k <00>H
[Range]
1 ≤ n ≤ Max. print columns – 1
1 ≤ k ≤ 16
[Outline]
This command sets the horizontal tab positions. n indicates the number of lines from the
head of the line to the horizontal tab setting position; n equals the set column position - 1." k
indicates the number of horizontal tab positions to be set.
The tab position is set at the character width × n from the head of the line. The character
width at this time includes the right space of the character and will be doubled if the double
width characters are specified.
The data <n>k indicating the set position is entered in the ascending order and ends with
<00>H. ESC D NUL clears all the set tab positions. After clearing the tab positions, HT will
be ignored.
[Caution]
If the data <n>k is equal to or smaller than the preceding data <n>k - 1, it is assumed that
horizontal tab setting has been completed. In that case, the subsequent data will be processed
as regular one.
Up to 16 tab positions can be set. If the data exceeds this limit, it will be processed as regular
data. If the data <n>k exceeds the one-line print range, the set column position will equal the
maximum print columns + 1.
If the character width is changed after setting the horizontal tab positions, they will not
change.
iDP-3410 User’s Manual
ESC "1"
[Function]
Setting the 1/9-inch line feed width
[Code]
<1B>H <31>H
[Outline]
This command sets the line feed width to 1/9 inch.
ESC "2"
[Function]
Setting the 2/9-inch line feed width
[Code]
<1B>H <32>H
[Outline]
This command sets the line feed width to 2/9 inch.
iDP-3410 User’s Manual
ESC "K" n1 <0> m1 m2 ...
[Function]
Specifying the 8-dot standard density bit image
[Code]
<1B>H <4B>H n1 <00>H m1 m2 ...
[Range]
1 ≤ n1 ≤ 378/2
[Outline]
This command prints the bit image by the number of data specified with n1. Printing will be
unidirectional. The surplus data exceeding the printable quantity in one line will be ignored.
The printer will automatically return to the character mode after printing the bit image.
iDP-3410 User’s Manual
ESC "L" n1 n2 m1 m2 ...
[Function]
Specifying the 8-dot double density bit image
[Code]
<1B>H <4C>H n1 n2 m1 m2 ...
[Range]
1 ≤ n1 + 256 × 2 ≤ 378
[Outline]
This command prints the 8-dot double density (Half-dot print) bit image. Printing will be
unidirectional. The surplus data exceeding the printable quantity in one line will be ignored.
The printer will automatically return to the character mode after printing the bit image.
The relations between the printing head pin numbers and the data are the same as the 8-dot
standard density bit image command. When printing the double density bit image, the
horizontally adjacent dots cannot be printed.
iDP-3410 User’s Manual
ESC "h" n
[Function]
Specifying/Canceling the double height character
[Code]
<1B>H <68>H n
[Outline]
The data following this command is printed in double height characters, except the bit image
mode <ESC> "K" and <ESC> "L". In combination with the <SO> command, this command
can print double height, double width characters.
It cannot be combined with the inverted character command, <SI>. The double height
characters and ordinary characters shall be bottom-justified.
n
0
30
1
31
Double height character command
Deselects
Selects
iDP-3410 User’s Manual
ESC "&" <O> n1 n2 m0 m1 m2 m3 m4 m5 m6 m7 m8 m9] n2 - n1 + 1
[Function]
Defining the download character set
[Code]
<1B>H <26>H <00>H n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1
[Range]
32 ≤ n1≤ n2 ≤ 255 m0 = 0 or m0 = 128
[Outline]
This command defines he download characters. n1 is a character code to start definition and
n2 is to end definition, respectively. When defining only one character, set n1 = n2. You can
define the ASCII codes ranging from 32 to 255.
The horizontally adjacent dots cannot be printed. Once the download bit image is defined, it
remains valid until it is redefined or the download deletion command(ESC DC2 n1 n2) is
executed.
Horizontal adjacent dots cannot be printed.
iDP-3410 User’s Manual
ESC "%" n
[Function]
Specifying/Canceling the download character set
[Code]
<IB>H <25>H n
[Outline]
This command selects/deselects the download character set. The download characters cannot
be printed by simply defining them with the above-mentioned ESC & 0 command. To print
them, send this command to the printer.
n
0
30
1
31
Download Character Set
Deselects
Selects
iDP-3410 User’s Manual
ESC BEL n1 n2
[Function]
Setting the external device drive pulse width
[Code]
<1B>H <07>H n1 n2
[Range]
1 ≤ n1 ≤ 127
1 ≤ n2 ≤ 127
[Outline]
This command sets the power-on time to drive an external device(Cash drawer).
Power-on time = n1 × 10 (ms)
Delay time = n2 × 10 (ms)
To actually drive the drawer, use the <BEL> and <FS> commands.
[Default]
n1 = n2 = 20 (200ms)
BEL
[Function]
Driving command A for drawing-1
[Code]
<07>H
[Outline]
This command drives the drawer connector no. 2 pin under the condition set with the
<ESC><BEL> n1 n2 command. This command is executed in order of entry into the input
buffer.
iDP-3410 User’s Manual
FS
[Function]
Driving command B for drawer-1
[Code]
<1C>H
[Outline]
This command drives the drawer connector no. 2 pin under the condition set with the
<ESC><BEL> n1 n2 command.
SUB
[Function]
Driving command for drawer-2
[Code]
<1A>H
[Outline]
As soon as this command is received, the drawer connector no. 5 pin is driven. The poweron time is 200 ms ON and 200 ms OFF stationary. The drawers 1 and 2 cannot be driven
simultaneously.
[Function]
Buzzer-on
[Code]
<1E>H
[Outline]
This command emits a short warning sound from the printer.
RS
iDP-3410 User’s Manual
CAN
[Function]
Canceling the print data
[Code]
<18>H
[Outline]
This command clears the input buffer and print buffer. In the STX-EXT mode of the serial
interface printer, the command clears the data in the data buffer and ends the STX-ETX
mode.
DC3
[Function]
Setting the deselect mode
[Code]
<13>H
[Outline]
If the printer receives <DC3>, it will ignore the subsequent data. The Deselect mode is
cancelled by <DC1>.
DC1
[Function]
Setting the select mode
[Code]
<11H>
[Outline]
If the printer receives this command, it will save the subsequent data in the input buffer.
iDP-3410 User’s Manual
ESC "U" n
[Function]
Selecting the Unidirectional/Bidirectional print mode
[Code]
<1B>H <55>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This commands selects or deselects unidirectional print.
n0 = 0
n0 = 1
Bidirectional print
Unidirectional print
ESC "@"
[Function]
Initializing the printer
[Code]
<1B>H <40>H
[Outline]
This command cancels various conditions set after power-on to initializes the printer to the
conditions having existed at power-on. However, the input buffer is not initialized.
iDP-3410 User’s Manual
ENQ
[Function]
Enquiry
[Code]
<05>H
[Outline]
This command is valid only for the serial interface. The printer sends the status information.
If this command is entered after receiving the text information in the STX-ETX mode, the
printer will send the status information and check byte.
iDP-3410 User’s Manual
STX
[Function]
Text start
[Code]
<02>H
[Outline]
This command is valid only for the serial interface. It effectuates the STX-ETX mode.
ETX
[Function]
Text end
[Code]
<03>H
[Outline]
This command is valid only for the serial interface. It ends the STX-ETX mode and prints
the data.
iDP-3410 User’s Manual
*ETX-STX Mode
1
STX/ETX Mode Start
Sends ENQ
Sends ENQ
Receives Status
Receives Status
NO
Receives Check Byte
YES
YES
NO
Data Buffer Empty ?
Status Error ?
YES
NO
YES
Sends STX
Check Byte
= Test Byte ?
NO
Odd Parity Check ?
Sends ETX
(Print)
Sets Test Byte To
FFH
Sets Test Byte To
00
NO
Sends CAN
NO
YES
STX-ETX
Mode End
YES
Exclusive ORs Test Byte
and Sent Data
Test Byte
ESC "t" n
STX-ETX Mode Data
Block Ready to Send ?
Sends Data to Printer
[Function]
Selecting the character code table
[Code]
<1B>H <74>H n
Last Data in 1 Block ?
[Range]
0 ≤ n ≤ 255
RET
[Outline]
This command selects Page-n of Character Code Table.
[Default]
1
Depends on DIP switch setting.
n
0
1
Character Code Table
STAR International
STAR Domestic
N
6
7
Character Code Table
Code Page 852 (Eastern Europe)
Code Page 866 (Russia)
iDP-3410 User’s Manual
2
3
4
5
Code Page 850 (Multilingual)
Code Page 860 (Portugal)
Code Page 863 (Canada-French)
Code Page 865 (Norway)
8
9
255
Code Page 857 (Turkey)
Windows Code
Space Page (For user setting)
iDP-3410 User’s Manual
ESC "⁄" n "data" CR or LF
[Function]
Defining the message
[Code]
<1B>H <2F>H n "data" CR or LF
[Range]
1 ≤ n ≤ 10
[Outline]
This command can define up to a 50-byte message in one line. If the value of n is specified
beyond the range, the data following n will be treated as the print data.
Once the message is defined, it remains valid until it is redefined. The data should end with
CR (0DH) or LF (0AH). If the data exceeds 50 bytes, the subsequent data will be treated as
the print data.
Once the message is defined, it remains valid until it is redefined or the download deletion
command (ESC DC2 n1 n2) is executed.
ESC "DC3" n
[Function]
Printing the message
[Code]
<1B>H <13>H n
[Range]
1 ≤ n ≤ 10
[Function]
This command prints a message. If the value of n is specified beyond the range, the message
will not be printed.
ESC DC2 n1 n2
[Function]
Deleting the download character, message, bit image
[Code]
<1B>H <12>H n1 n2
[Range]
0 ≤ n1≤ 3
0 ≤ n2
(Specify 0 at n1 = 0)
(1 ≤ n2 ≤ 10 at n1 = 1)
(32 ≤ n2 ≤ 224 at n1 = 2)
(Specify 0 at n1 = 3)
[Outline]
This command deletes the downloaded characters, message, and bit image.
n1
0
1
Object Deleted
All(Message, characters, bit image)
Download message
iDP-3410 User’s Manual
2
3
Download characters
Download bit image
With n2, specify which data of the function specified with n1 should be deleted.
n2 = 0
Deletes all the download function specified with n1.
n2≠0
Deletes the data downloaded at the value specified with n2 (Value specified
when saving with each download command), of the download function
specified with n1.
Note) No meaning when n1 = 0 is set.
iDP-3410 User’s Manual
GS "∗" n1 n2 [d] n1 × n2 × 8
[Function]
Defining the download, bit image
[Code]
<1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8
[Range]
1 ≤ n1 ≤ 45 0 ≤ n2 ≤ 24
Note) Take care that the number of data(n1×n2×8) is equal to or smaller than 2,048.
[Outline]
This command defines the download bit image having the dots specified n1 and n2. The
number of horizontal dots is represented by n1 × 8 and that of vertical dots is represented by
n2 × 8, respectively. m denotes the number to be registered. (See a download bit image
printout.) d denotes the bit image data. Once the download bit image is defined, it remains
valid until it is redefined or the download deletion command(ESC DC2 n1 n2) is executed.
iDP-3410 User’s Manual
GS ⁄ m
[Function]
Printing the download, bit image
[Code]
<1D>H <2F>H m
[Range]
0 ≤ m ≤ 255
[Outline]
This command prints the bit image saved in the number specified with m.
[Caution]
If the print buffer contains the data, this command will be ignored. If the bit image has not
been saved in the specified number, this command will be ignored.
Nothing is printed when m is other than 0,1,2 or 3.
13.3
ESC/POS Commands
13.3.1 Command List
Command
Function
1 HT
Horizontal tab
2 LF
Printing and paper feed
3 CR
Printing
4 ESC " " n
Setting thr character right space
5 ESC ! n
Setting print mode batch
6 ESC % n
Specifying/Canceling the download character set
ESC & s n m
7
Defining the download character set
[a[p] s × a]
ESC ∗ m n1 n2
8
Specifying the bit image mode
[d] n1 + 256 × n2
9 ESC 2
Setting the 1/6-inch line feed rate
10 ESC 3 n
Setting the line feed width in minimum pitch
Code
09H
0AH
0DH
1BH 20H n
1BH 21H n
1BH 25H n
1BH 26H s n m
[a[p] a×a] m-n+1
1BH 2AH m n1 n2
[d] n1 + 256×n2
1BH 32H n
1BH 33H n
Page
105
105
106
106
107
108
109
110
111
111
iDP-3410 User’s Manual
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
ESC <
ESC @
ESC D [n] k NUL
ESC J n
ESC R n
ESC U n
ESC c 0 n
ESC c 5 n
ESC d n
ESC p m n1 n2
ESC r n
ESC t n
ESC u n
ESC v
ESC { n
GS E n
ESC ⁄ n
ESC DC3 n
29
ESC DC2 n1 n2
30
31
GS ∗ n1 n2
GS ⁄ m
increments
NOP
Initializing the printer
Setting the Horizontal tab position
NOP
Selecting the international character set
Specifying/Canceling the unidirectional print mode
NOP
Selecting the panel switch enable/disable
Printing and n-line paper feed
Specifying the pulse generation
Selecting the printing color
Selecting the character code table
Sending the status for peripheral device
Sending the printer status
Specifying/Canceling the inverted character print
NOP
Defining the message
Printing the message
Deleting the download character, message, bit
image
Defining the download, bit image
Printing the download, bit image
1BH 3CH
1BH 40H
1BH 44H [n] k 00
1BH 4AH n
1BH 52H n
1BH 55H n
1BH 63H 30 n
1BH 63H 35H n
1BH 64H n
1BH 70H m n1 n2
1BH 72H n
1BH 74H n
1BH 75H n
1BH 76H
1BH 7BH n
1DH 45H n
1BH 2FH n
1BH 13H n
111
112
113
114
115
116
117
118
118
119
120
121
121
122
1BH 12H n1 n2
123
1DH 2AH n1 n2
1DH 2FH m
124
125
iDP-3410 User’s Manual
Details
HT
[Function]
Horizontal tab
[Code]
<09>H
[Outline]
This command moves a printing position to the next horizontal tab position. If the next
horizontal tab position is not set, this command will be ignored.
[Caution]
The horizontal tab position is set by <ESC> D. Initial setting of the horizontal tab position is
every 8 characters (9th, 17th, 25th culomns, and so on) of the 7×9 font.
[Function]
Printing and paper feed
[Code]
<0A>H
[Outline]
This command prints one line worth of the data saved in the print buffer and feeds the line
based on the set line feed value. The head of the line is assumed to be the next print start
position.
LF
iDP-3410 User’s Manual
CR
[Function]
Printing
[Code]
<0D>H
[Outline]
This command prints the data. If the DIP switch segments 1 to 6 are set to OFF, the printer
will print the data in the print buffer and feed the paper by one line. If they are set to ON, the
printer will print the data in the print buffer and will not feed the paper.
ESC " " n
[Function]
Setting the character right space
[Code]
<1B>H <20>H n
[Range]
0 ≤ n ≤ 32
[Outline]
This command sets the right space of the character.
[Caution]
In the double width mode, the right space will be double the set amount. Set the space in
increments of half dot.
[Default]
n=0
iDP-3410 User’s Manual
ESC "!" n
[Function]
Setting the print mode batch
[Code]
<1B>H <21>H n
[Range]
0 ≤ n ≤ 255
[Outline]
Sets the print mode. "n" (Each bit) has the following meanings.
Bit
Function
0
1
2
3
4
5
6
7
Undefined
Undefined
Undefined
High-lighting
Double height
Double width
Undefined
Underline
Values
0
1
−
−
−
−
−
−
Canceled
Canceled
Canceled
Specified
Specified
Specified
Canceled
Specified
−
−
[Caution]
The entire character print width is underlined, but the portion skipped by HT is not. If both
double height and double width are selected, the characters will be quadrupled. If the double
width characters are selected, some dots may not be printed depending on the preceding one.
When printing the double height characters, there will be less shear in unidirectional printing.
[Default]
n=0
iDP-3410 User’s Manual
ESC "%" n
[Function]
Specifying/Canceling the download character set
[Code]
<1B>H <25>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects/deselects the download character set. n is valid only for the least
significant bit.
Setting n0 = 1 selects the download character set.
Setting n0 = 0 deselects the download character set.
[Default]
n=0
iDP-3410 User’s Manual
ESC "&" s n m [a[p] s × a]m - n + 1
[Function]
Defining the download character set
[Code]
<1B>H <26>H s n m [a[p] ... <ps × a>] m - n + 1
[Range]
s=2
32 ≤ n ≤ m ≤ 255
0≤a≤9
0 ≤ p1 ... ps × a ≤ 255
[Outline]
This command defines the download alphenumerals or Katakana. s denotes the number of
bytes in the vertical direction, n the start character code, and m the end character code,
respectively. When defining only one character, set n = m.
The 224 ASCII code characters, 32 to 255, are definable. a specifies the number of dots in
the horizontal direction to be defined. p is the data you want to define and shows the a-dots
worth of pattern in the horizontal direction from the left edge. The remaining pattern on the
right side will be a space. Once the download characters are defined, they remain valid until
they are redefined or the download deletion command (ESC DC2 n1 n2) is executed.
[Default]
Same as the internal character set.
[Caution]
The horizontally adjacent dots cannot be printed. The 2nd-byte data in the vertical direction
is valid only for the most significant bit.
iDP-3410 User’s Manual
ESC "∗" m n1 n2 [d] n1 + 256 × n2
[Function]
Specifying the bit image mode
[Code]
<1B>H <2A>H m n1 n2 [d] n1 + 256×2
[Range]
m = 0, 1
0 ≤ n1 ≤ 255
0 ≤ n2 ≤ 3
0 ≤ d ≤ 255
[Outline]
This command specifies the bit image for the mode m as to the number of dots specified with
n1 and n2. Divide the number of dots printed by 256 and assume its quotient to be n2 and
remainder to be n1. Therefore, the number of horizontal dots will be n1 + 256 × n2.
If the bit image data is entered beyond the dot positions printable in one line, the surplus data
will be discarded. The following table shows the bit image modes for m.
m
0
1
[Caution]
Vertical
Dots
8
8
Dot Density
Single density
Double density
Horizontal Direction
Adjacent Dot
Setting
Allowed
Disallowed
Total Dots
189
378
If the value of m is beyond the conditions, the data subsequent to n1 will be processed as
normal data. Normal data processing will be restored after completing bit image print.
iDP-3410 User’s Manual
ESC "2"
[Function]
Setting the 1/6-inch line feed width
[Code]
<1B>H <32>H
[Outline]
This command sets the line feed width to 1/6 inch.
ESC "3"
[Function]
Setting the line feed width in minimum pitch increments
[Code]
<1B>H <33>H
[Outline]
This command sets the line feed width to n/18 inch.
ESC "@"
[Function]
Initializing the printer
[Code]
<1B>H <40>H
[Outline]
This command cancels various conditions set after power-on to initializes the printer to the
conditions having existed at power-on. However, the print buffer, input buffer, and external
device drive pulse width are not initialized. The settings of the DIP switch segments are not
re-read.
iDP-3410 User’s Manual
ESC "D" [n]k NUL
[Function]
Setting the Horizontal tab position
[Code]
<1B>H <44>H [n]k <00>H
[Range]
1 ≤ n ≤ 255
0 ≤ k ≤ 32
[Outline]
This command sets the horizontal tab position. n denotes the number of columns from the
head of the line to the horizontal tab setting position and equals the set column position - 1. k
denotes the number of horizontal tab positions to be set. The tab position is set at the
character width × n from the head of the line. The character width at this time includes the
space to the right of the character; it will be double the normal character width if the double
width characters are selected.
The data <n>k denoting the set position is entered in the ascending order and ends with
<00>H. ESC D NUL clears all the set tab positions. HT is ignored after clearing.
[Caution]
If the data <n>k is equal to or smaller than the preceding data <n>k - 1, it is assumed that
horizontal tab setting has been completed. If this is the case, the subsequent data will be
processed as normal data.
Up to 16 horizontal tabs can be set. The data beyond this limit are processed as normal ones.
If the data <n>k exceeds the one-line print range, set the "set column position = maximum
print columns + 1."
Even if the character width is changed after setting the horizontal tab position, the latter will
not change.
[Default]
7×9 font, every 8 characters (9th, 17th, 25th column, and so on)
iDP-3410 User’s Manual
ESC "R" n
[Function]
Selecting the international character set
[Code]
<1B>H <52>H n
[Range]
0 ≤ n ≤ 10
[Outline]
This command selects the international characters according to the value of n.
n
0
1
2
3
4
5
[Default]
Character Set
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
Depends upon DIP switch setting.
n
6
7
8
9
10
Character Set
Italy
Spain
Japan
Norway
Denmark II
iDP-3410 User’s Manual
ESC "U" n
[Function]
Specifying/Canceling the Unidirectional print mode
[Code]
<1B>H <55>H
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects/deselects unidirectional print. n is valid only for the least significant
bit.
n
0
1
[Caution]
Function
Deselects
Selects
If unidirectional print is selected, the printer will print from the left to the right. When you
want to prevent horizontal shear in printing at high accuracy, specify unidirectional print with
this command. (Double height print, etc.)
ESC "c" "5" n
[Function]
Selecting the panel switch enable/disable
[Code]
<1B>H <63>H <35>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command enables/disables the panel switches. n is valid only for the least significant
bit.
Setting n = 1 disables the panel switches.
Setting n = 0 enables the panel switches.
[Caution]
If the panel switches are disabled with this command, the LF switch will be disabled.
Therefore, the paper cannot be fed by the LF switch.
iDP-3410 User’s Manual
[Default]
n=0
ESC "d" n
[Function]
Printing and n-line paper feed
[Code]
<1B>H <64>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command feeds the paper by n-lines after printing the one line worth of data saved in the
print buffer.
iDP-3410 User’s Manual
ESC "p" m n1 n2
[Function]
Specifying the pulse generation
[Code]
<1B>H <70>H m n1 n2
[Range]
0≤m≤1
0 ≤ n1 ≤ n2 ≤ 255
[Outline]
This command outputs the signals specified with n1 and n2 to the connector pins.
m
0
1
Connector Pin
Drawer kick connector No. 2 pin
Drawer kick connector No. 5 pin
The ON time is n1×2 mS and the OFF time is n2×2 mS.
[Caution]
The user should consider driving the drawer at the following duty ratio.
ON time ÷ (ON time + OFF time) ≤ 0.2
(It is recommended to make n2 four times higher or more than n1.)
The drawer kick-out solenoid should have a resistance value of 36Ω or more. Do not use a
lower one because an overcurrent will flow. For the drawer power, be sure to use the printer
power (Drawer kick-out connector No. 4 pin).
iDP-3410 User’s Manual
ESC "r" n
[Function]
Selecting the printing color
[Code]
<1B>H <72>H n
[Range]
n = 0, 1
[Outline]
This command selects a print color for each line. Setting n = 0 selects black. Setting n = 1
selects red. The command is valid only when it is entered at the head of the line.
[Default]
n = 0 (Black print)
ESC "t" n
[Function]
Selecting the character code table
[Code]
<1B>H <74>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects Page-n of Character Code Table.
[Default]
Depends on DIP switch setting.
n
0
1
2
3
4
5
Character Code Table
Code Page 437 (U.S.A.)
Katakana
Code Page 850 (Multilingual)
Code Page 860 (Portugal)
Code Page 863 (Canada-French)
Code Page 865 (Norway)
N
6
7
8
9
255
Character Code Table
Code Page 852 (Eastern Europe)
Code Page 866 (Russia)
Code Page 857 (Turkey)
Windows Code
Space Page (For user setting)
iDP-3410 User’s Manual
ESC "u" n
[Function]
Sending the status for peripheral device
[Code]
<1B>H <75>H n
[Range]
n=0
[Outline]
This commands sends the status of the connector no. 3 pin.
n
0
Connector Pin
Drawer kick-out connector No. 3 pin
Status Sent
[Caution]
Bit
Function
0
1
2
3
4
5
6
No. 3 pin's level
Undefined
Undefined
Undefined
Undefined
Undefined
Undefined
Value
0
“LOW”
1
“HIGH”
This command is valid only for the serial interface. If nothing is connected to the connector,
the bit 0 will be always "1". In case of DTR/DSR control, if the host cannot receive (DSR
signal has the Mark status), the printer will wait until it will be ready to receive. In case of
XON/XOFF control, only one byte will be sent without confirming the status of the DSR
signal. Note that it may take time to send the status after receiving the command.
iDP-3410 User’s Manual
ESC "v"
[Function]
Sending the printer status
[Code]
<1B>H <76>H
[Outline]
This command sends the printer status.
[Caution]
This command is valid only for the serial interface. The following table lists the status sent.
In case of DTR/DSR control, only one byte will be sent after confirming that the host is ready
to receive (DSR signal has the Space status).
The status at command processing time is sent after processing the data received prior to this
command. If the printing is under way when the command is being processed, however, the
then status will be sent after completing print feed of that line. Therefore, it may take time to
send the status after receiving the command.
Bit
Function
0
1
2
3
4
5
6
Paper near end
Undefined
Paper near end
Undefined
Undefined
Undefined
Undefined
Value
0
With paper
1
Near end
With paper
End
0 stationary
−
iDP-3410 User’s Manual
ESC "{ " n
[Function]
Specifying/Canceling the inverted character print
[Code]
<1B>H <7B>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects/deselects inverted print. n is valid only for the least significant bit.
n
0
1
Type
Deselects the inverted characters.
Selects the inverted characters.
[Caution]
This command is valid only if entered at the head of the line.
[Default]
n=0
<Example>
When Inverted Print Is
Deselected
When Inverted Print Is
Selected
Print
Direction
ESC "⁄" n "data" CR or LF
[Function]
Defining the message
[Code]
<1B>H <2F>H n “data” CR or LF
[Range]
1 ≤ n ≤ 10
[Outline]
This command defines up to a 50-byte message in one line. If the value of n is specified
beyond the range, the data following n will be treated as the print data.
Once the message is defined, it remains valid until it is redefined. The data should end with
CR (0DH) or LF (0AH). If the data exceeds 50 bytes, the subsequent data will be treated as
the print data.
Once the message is defined, it remains valid until it is redefined or the download deletion
command (ESC DC2 n1 n2) is executed.
iDP-3410 User’s Manual
ESC DC3 n
[Function]
Printing the message
[Code]
<1B>H <13>H n
[Range]
1 ≤ n ≤ 10
[Function]
This command prints a message. If the value of n is specified beyond the range, the message
will not be printed.
iDP-3410 User’s Manual
ESC DC2 n1 n2
[Function]
Deleting the download character, message, bit image
[Code]
<1B>H <12>H n1 n2
[Range]
0 ≤ n1 ≤ 3
0 ≤ n2
(Specify 0 at n1 = 0)
(1 ≤ n2 ≤ 10 at n1 = 1)
(32 ≤ n2 ≤ 224 at n1 = 2)
(Specify 0 at n1 = 3)
[Outline]
This command deletes the downloaded characters, message, and bit image.
n1
0
1
2
3
Object Deleted
All(Message, characters, bit image)
Download message
Download characters
Download bit image
With n2, specify which data of the function specified with n1 should be deleted.
n2 = 0
Deletes all the download function specified with n1.
n2≠0
Deletes the data downloaded at the value specified with n2 (Value specified
when saving with each download command), of the download function
specified with n1.
Note) No meaning when n1 = 0 is set.
iDP-3410 User’s Manual
GS "∗" n1 n2 [d] n1 × n2 × 8
[Function]
Defining the download, bit image
[Code]
<1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8
[Range]
1 ≤ n1 ≤ 45
0 ≤ n2 ≤ 24
Note) Take care that the number of data(n1×n2×8) is equal to or smaller than 2,048.
[Outline]
This command defines the download bit image having the dots specified n1 and n2. The
number of horizontal dots is represented by n1×8 and that of vertical dots is represented by
n2×8, respectively. m denotes the number to be registered. (See a download bit image
printout.) d denotes the bit image data. Once the download bit image is defined, it remains
valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed.
iDP-3410 User’s Manual
GS ⁄ m
[Function]
Printing the download, bit image
[Code]
<1D>H <2F>H m
[Range]
0 ≤ m ≤ 255
[Outline]
This command prints the bit image saved in the number specified with m.
[Caution]
If the print buffer contains the data, this command will be ignored. If the bit image has not
been saved in the specified number, this command will be ignored.
Nothing is printed when m is other than 0, 1, 2 or 3.
iDP-3410 User’s Manual
14.
CHARACTER CODES TABLE
14.1 CBM (Domestic)
iDP-3410 User’s Manual
14.2 CBM (International)
iDP-3410 User’s Manual
14.3 STAR (Domestic)
iDP-3410 User’s Manual
14.4 STAR (International)
iDP-3410 User’s Manual
14.5 Code Page 437
iDP-3410 User’s Manual
14.6 Katakana
iDP-3410 User’s Manual
14.7 Code Page 850
iDP-3410 User’s Manual
14.8 Code Page 860
iDP-3410 User’s Manual
14.9 Code Page 863
iDP-3410 User’s Manual
14.10Code Page 865
iDP-3410 User’s Manual
14.11Code Page 852
iDP-3410 User’s Manual
14.12Code Page 866
iDP-3410 User’s Manual
14.13Code Page 857
iDP-3410 User’s Manual
14.14Windows Code
iDP-3410 User’s Manual
14.15International Character Codes Table
iDP-3410 User’s Manual
APPENDIX 1. BLOCK DIAGRAM
OSC16MHz
Driver
POWER LED
ERROR LED
FEED Switch
DIP Switch
Drawer
Driver
Parallel
Interface
Print
Head
CPU
Paper
End
Driver
DC
Moter
Driver
(CENTRONICS
ROM
Based)
RAM
Serial
Printer
Mechanism
(RS-232C Based)
Reset
Vp Vcc
Vp :For mechanism drive,
AC Adapter
34 AD Series
(26V DC, 1.15A)
Filter
Power
Supply
For drawer kick
VCC:For circuit drive
iDP-3410 User’s Manual
APPENDIX 2. OUTLINE DRAWING
iDP-3410 User’s Manual
<<<German>>>
<VORSICHT>
1. Bitte lesen Sie die Bedienungsanleitung vor dem Betrieb des Geräts aufmerksam durch und bewahren Sie die
Anleitung anschließend für späteres Nachschlagen an einem sicheren Platz auf.
2. Änderungen des Inhalts dieser Anleitung bleiben ohne Vorankündigung vorbehalten.
3. Die Vervielfältigung dieser Bedienungsanleitung ohne vorherige Genehmigung verstößt, auch auszugsweise,
gegen das Urheberschutzrecht.
4. Niemals versuchen, in dieser Anleitung nicht erwähnte Geräteteile eigenhändig zu warten, zerlegen oder zu
reparieren.
5. Bitte beachten Sie, daß wir keinerlei Haftung für Schäden übernehmen, die auf unsächgemäße Bedienung, falsche
Handhabung oder eine ungeeignete Betriebsumgebung zurückzuführen sind.
6. Zur Vermeidung von Unfällen und sonstigen Problemen ist das Gerät ausschließlich auf die in der
Bedienungsanleitung beschriebene Weise zu betreiben.
7. Daten sind grundsätzlich temporär, d.h. sie können nicht permanent gesichert oder über längere Zeit gespeichert
werden. Es sei deshalb darauf hingewiesen, daß wir für finanzielle Schäden oder Profitrückgänge als Folge von
Datenverlust, Unfällen, Reparaturen, Tests usw. keinerlei Haftung übernehmen.
8. Bitte wenden Sie sich mit Fragen oder Hinweisen auf Fehler oder Auslassungen im Text dieser Anleitung an
unsere Geschäftsstelle.
iDP-3410 User’s Manual
9. Beachten Sie jedoch, daß wir, ungeachtet des obigen Punkts 8, keinerlei Haftung für negative
Folgeerscheinungen im Zusammenhang mit dem Betrieb dieses Geräts übernehmen.
iDP-3410 User’s Manual
ZU BEACHTENDE SICHERHEITSMASSREGELN
Zur Vermeidung von Gefahren gegenüber dem Bediener und anderen Personen und Sachschäden sind die
folgenden Vorsichtsmaßregeln unbedingt zu beachten.
_ Der folgende Text beschreibt das Ausmaß der Gefahren und potentiellen Sachschäden, die durch eine
Mißachtung der Bedienungshinweise oder durch die unsachgemäße Handhabung des Geräts entstehen
können.
WARNUNG
Die Mißachtung dieser Vorsichtsmaßregel kann zu Körperverletzungen mit
möglicher Todesfolge führen.
VORSICHT
Die Mißachtung dieser Vorsichtsmaßregel kann zu Körperverletzungen oder
Sachschäden führen.
Dieses Symbol ruft den Bediener zu erhöhter Wachsamkeit auf.
Dieses Symbol weist auf wichtige Informationen, wie z.B. Bedienungsschritte oder dergleichen, hin.
iDP-3410 User’s Manual
WARNUNG
_ Beim Betrieb des Geräts sind die nachfolgenden Vorsichtsmaßregeln unbedingt zu beachten. Eine
Mißachtung dieser Hinweise kann zu Schäden, Funktionsstörungen, Rauchentwicklung und Brandgefahr
durch Überhitzen und zu elektrischen Schlägen führen.
Der fortgesetzte Betrieb des Geräts in anormalem Zustand, wie z.B. nach einer Beschädigung, kann
Funktionsstörungen, Rauchentwicklung, fremde Gerüche/Geräusche und Brände verursachen. Bei
anormalem Betriebszustand das Gerät sofort ausschalten und an einen Fachhändler wenden. Niemals
versuchen, das Gerät eigenhändig zu reparieren, um ernsthafte Gefahren zu vermeiden.
• Das Gerät vor starken Stößen und Erschütterungen, wie z.B. Tritte, Stampfen, Schläge, Herunterfallen
usw., schützen.
• Das Gerät an einem gut belüfteten Platz aufstellen, und darauf achten, die Belüftungsöffnung nicht zu
blockieren.
• Bei der Aufstellung des Geräts Plätze vermeiden, an denen chemische Reaktionen auftreten, wie z.B. in
einem Labor, sowie Plätze mit salz- oder gashaltiger Umgebungsluft.
• Netz- und Datenkabel niemals am Kabel haltend anschließen oder abziehen. Bei Betrieb, Verrücken
oder Tragen des Geräts darauf achten, daß die Kabel keiner Gewalteinwirkung ausgesetzt sind.
• Darauf achten, daß keine Fremdköper, wie z.B. Nadeln oder Büroklammern, in das Gerät gelangen.
• Darauf achten, keine Flüssigkeiten auf dem Gerät zu vergießen oder chemische Substanzen enthaltende
Sprays darüber zu versprühen. Bei versehentlichem Naßwerden das Gerät sofort ausschalten, das
Stromanschlußkabel abziehen, das Netzkabel von der Steckdose trennen usw. und an einen Fachhändler
wenden.
• Das Gerät niemals eigenhändig zerlegen oder modifizieren. Eine Mißachtung dieser Vorsichtsmaßregel
kann zu Bränden und elektrischen Schlägen führen.
• Das Netzteil bei versehentlichem Herunterfallen sofort von der Steckdose trennen und sich an einen
Fachhändler wenden. Der fortgesetzte Betrieb in diesem Zustand kann Brände und elektrische Schläge
verursachen.
• Sollte unbeabsichtigt Wasser in das Gerät eindringen, sofort den Netzstecker abziehen und an einen
Fachhändler wenden. Der fortgesetzte Betrieb in diesem Zustand kann zu Bränden und elektrischen
Schlägen führen.
• Das Gerät ausschließlich mit der vorgeschriebenen Netzspannung betreiben. Eine Mißachtung dieser
Vorsichtsmaßregel kann Brände, elektrische Schläge und Funktionsstörungen verursachen.
• Das Kabel des Netzteils niemals beschädigen, knicken, modifizieren, biegen, verdrehen, bündeln oder
gewaltsam daran ziehen. Das Kabel darüber hinaus von Wärmequellen fernhalten und keine schweren
Gegenstände darauf stellen. Ein beschädigtes Netzteil kann Brände, elektrische Schläge und
Funktionsstörungen verursachen.
• Wenden Sie sich bei einer Beschädigung des Netzteilkabels bitte an unsere Kundendienstvertretung.
• Das Netzteil niemals mit nassen Händen anschließen oder trennen. Hierdurch können Brände,
elektrische Schläge und sonstige Probleme entstehen.
_ Verpackungsbeutel sind vorschriftsgemäß zu entsorgen oder ansonsten von Kindern fernzuhalten.
Kleinkinder können durch Überstreifen eines Plastikbeutels ersticken.
iDP-3410 User’s Manual
VORSICHTSMASSREGELN FÜR DIE AUFSTELLUNG
• Das Gerät nicht an Plätzen abstellen oder betreiben, an denen es Feuer, Feuchtigkeit oder direkter
Sonnenbestrahlung ausgesetzt ist. Ebenso sind Plätze in der Nähe von Heizkörpern und sonstigen
Wärmenquellen zu vermeiden, an denen Umgebungstemperatur und Luftfeuchtigkeit nicht den
vorgeschriebenen Betriebsbedingungen entsprechen, sowie Plätze, an denen das Gerät Öl, Metallspänen oder
Staub ausgesetzt ist. Andernfalls können Funktionsstörungen sowie Rauch- und Brandentwicklung die Folge
sein.
• Bei der Aufstellung des Geräts Plätze vermeiden, an denen chemische Reaktionen auftreten, wie z.B. in
einem Labor, sowie Plätze mit salz- oder gashaltiger Umgebungsluft. Hierbei besteht die Gefahr von Bränden
und elektrischen Schlägen.
• Keine schweren Gegenstände auf den Drucker stellen, um mögliche Probleme zu vermeiden.
• Das Gerät nicht in der Nähe eines Radios oder Fernsehers verwenden und nicht zusammen mit einem Radio
oder Fernseher an die gleiche Steckdose anschließen. Hierdurch können Empfangsstörungen auftreten.
• Das Gerät ausschließlich mit der vorgeschriebenen Netzspannung und -frequenz betreiben. Eine Mißachtung
dieser Vorsichtsmaßregel kann Brände, elektrische Schläge und Funktionsstörungen verursachen.
• Vergewissern, daß die für den Anschluß des Netzkabels verwendete Steckdose über eine ausreichende
Kapazität verfügt.
• Darauf achten, eine einzelne Steckdose nicht durch den Anschluß des Netzkabels zu überlasten. Andernfalls
können Brände und Stromausfälle die Folge sein. Darüber hinaus nicht fest auf das Netzkabel treten oder
schwere Gegenstände darauf abstellen.
• Erdungskabel niemals an ein Gasrohr anschließen, da hierbei Explosionsgefahr besteht. Vor dem
Anschließen oder Trennen eines Erdungskabels unbedingt zuerst den Netzstecker aus der Steckdose ziehen.
• Beim Anschließen oder Trennen der Kabel zuerst die Netzversorgung ausschalten, einschließlich der
angeschlossenen Seite, und dann an Stecker und Steckdose haltend anschließen bzw. trennen. Bei einem
Transport des Geräts darauf achten, daß das Kabel keinem Zug ausgesetzt ist.
• Steckerkabel sind fest anzuschließen. Durch Anschluß mit umgekehrter Polarität können Innenbauteile oder
Paßflächen beschädigt werden.
• Für Datensignalleitungen abgeschirmte Kabel oder verzwirbelte Doppeladerkabel verwenden, um
Rauschstörungen möglichst gering zu halten. Der Anschluß an ein Rauschstörungen erzeugendes Gerät ist zu
vermeiden.
• Falls ein Geldschubladen-Ausschubmechanismusstecker vorhanden ist, sollten keine anderen Vorrichtungen, die
nicht den vorgeschriebenen Solenoidspezifikationen entsprechen, angeschlossen werden. Eine Mißachtung dieser
Vorsichtsmaßregel kann zu Fehlfunktionen führen.
• Das Gerät an einem Platz in der Nähe einer Steckdose betreiben, wo sich der Netzstecker zum Unterbrechen
der Stromversorgung jederzeit schnell und mühelos abziehen läßt.
• Das Netzkabel aus der Steckdose ziehen, wenn das Gerät längere Zeit lang nicht benutzt werden soll.
• Vor einem Transport die Papierrolle aus dem Gerät herausnehmen.
• Das Gerät auf einer ebenen, stabilen Tischplatte an einem gut belüfteten Platz und frei von Erschütterungen
aufstellen. (Darauf achten, die Belüftungsöffnung nicht zu blockieren.)
iDP-3410 User’s Manual
VORSICHTSMASSREGELN FÜR DIE HANDHABUNG
Zur Vermeidung von Problemen sind bei der Handhabung des Geräts die folgenden Vorsichtsmaßregeln zu
beachten.
• Für die Stromversorgung ausschließlich das vorgeschriebene Netzteil verwenden.
• Den Druckbetrieb nicht ohne eingelegtes Papier oder ohne Farbband starten, da hierdurch der
Druckkopf beschädigt werden kann.
• Darauf achten, daß keine Fremdköper, wie z.B. Nadeln, Büroklammern oder Schrauben, in das Gehäuse
gelangen.
• Darauf achten, keine Flüssigkeiten auf dem Gerät zu vergießen oder chemische Substanzen enthaltende
Sprays darüber zu versprühen.
• Das Gerät vor starken Stößen und Erschütterungen bewahren und nicht fallen lassen.
• Niemals mit spitzen Objekten, wie z.B. einem Kugelschreiber, auf das Bedienfeld drücken.
• Papierblätter niemals zum fortlaufenden Drucken mit Klebestreifen zusammenkleben.
• Ein bereits eingezogenes Blatt niemals gewaltsam herausziehen. Beim Öffnen/Schließen der
Druckerabdeckung darauf achten, daß sich das Papier nicht verfängt.
Zur Vermeidung von Verletzungen und Schäden
• Den druckenden Abschnitt des Druckkopfes nicht berühren.
• Bei Einschalten keine beweglichen Teile, wie z.B. Schneidklinge und Zahnrad im Druckergehäuse, oder
elektrische Teile berühren.
• Darauf achten, körperliche Verletzungen und die Beschädigung anderer Objekte durch scharfe Kanten
zu vermeiden.
• Bei Auftreten jeglicher Störungen während des Betriebs den Drucker sofort ausschalten, und das
Netzkabel aus der Steckdose ziehen.
• Die Beseitigung von Betriebsstörungen ist qualifiziertem Fachpersonal zu überlassen. Niemals
versuchen, das Gerät eigenhändig zu zerlegen.
• Beim Öffnen/Schließen der Druckerabdeckung darauf achten, nicht die Hand oder Finger am Drucker
einzuklemmen.
iDP-3410 User’s Manual
TÄGLICHE WARTUNG
• Vor der Wartung zuerst den Drucker ausschalten.
• Schmutz und Staub mit einem trockenen, weichen Tuch vom Druckergehäuse abwischen. Bei starker
Verschmutzung einen Lappen in Wasser anfeuchten, auswringen und damit abwischen. Hierzu niemals
flüchtige organische Lösungsmittel, wie z.B. Alkohol, Terpentin, Trichlorethan, Benzol, Keton oder
chemische Staubentfernungsmittel, verwenden.
• Papierstaub mit einer weichen Bürste vom Gehäuse entfernen.
4. BETRIEB
4.1
Anschluß des Netzteils
1. Den Netzschalter drücken.
2. Den Kabelstecker des Netzteils an die Netzanschlußbuchse an der Rückwand des Druckers anschließen.
3. Um Anschlußunterbrechungen vorzubeugen, den Kabelstecker, wie in der untenstehenden Abbildung
gezeigt, mit Drahtklemmen sichern.
4. Den Netzstecker des Netzteils an eine Wandsteckdose anschließen.
VORSICHT: • Ausschließlich das vorgeschriebene Netzteil verwenden.
• Das Netzteil nicht zusammen mit Geräten, die Rauschstörungen erzeugen, an die
gleiche Steckdose anschließen.
• Das Zubehör-Netzteil nicht für den Anschluß anderer Geräte oder Vorrichtungen,
sondern ausschließlich für diesen Drucker, verwenden.
Beim Trennen des Netzteils von der Steckdose stets am Stecker anfassen; niemals
iDP-3410 User’s Manual
am Kabel ziehen.
• Durch Ziehen am Netzadapter-Anschlußkabel können Schäden entstehen, die zu
Bränden, elektrischen Schlägen oder gebrochenen Kabeldrähte führen.
• Bei einem Gewitter sollte das Netzteil von der Steckdose getrennt und der Drucker
nicht verwendet werden. Ein Blitzschlag kann Brände und elektrische Schläge
auslösen.
• Das Netzteil-Anschlußkabel von Wärmequellen fernhalten. Die Kabelisolierung
kann schmelzen und Brände und elektrische Schläge verursachen.
• Wenn der Drucker längere Zeit lang nicht benutzt wird, sollte das Netzteil aus
Sicherheitsgründen von der Steckdose getrennt werden.
iDP-3410 User’s Manual
4.2
Anschluß des Schnittstellenkabels
1. Den Drucker (einschließlich angeschlossene Geräte) ausschalten.
2. Den Kabelstecker korrekt ausgerichtet (Ober- und Unterseite prüfen) an die Schnittstellenbuchse anschließen.
3. Die Kabelstecker befestigen:
•Seriellschnittstelle: durch Festziehen der Schrauben sichern.
•Parallelschnittstelle: durch Drehen des Anschlags sichern.
•DIN-Minischnittstelle: bis zum Einrasten einschieben.
4. Das Kabel an einen Computer anschließen.
4.3
Anschluß des Ausschubmechanismussteckers der Geldschublade
1. Den Drucker mit dem Netzversorgung ausschalten.
2. Den Ausschubmechanismusstecker korrekt ausgerichtet (Ober- und Unterseite prüfen) an die GeldschubladenAusschubmechanismusbuchse an der Rückwand des Druckers anschließen.
3. Das Erdungskabel der Geldschublade an das Erdungsterminal am Drucker anschließen.
VORSICHT:
Ausschließlich
die
vorgeschriebene
Ausschubmechanismusstecker anschließen.
Geldschublade
(Solenoid)
an
den
iDP-3410 User’s Manual
4.4
Einsetzen der Farbbandkassette
1. Die Druckerabdeckung aufklappen.
2. Bei schlaffem Farbband den Knopf in Pfeilrichtung drehen, um das Band vor dem Einsetzen der Kassette
straff zu wickeln.
3. Die Farbbandkassette zwischen Druckkopfabdeckung und Walze einsetzen und gleichzeitig die
Halteklauen in den Halter des Druckers drücken.
4. Das Farbband durch Drehen des Farbband-Kassettenknopfes in Pfeilrichtung straff wickeln.
5. Zum Herausnehmen der Farbbandkassette die Halteklauen an beiden Seiten zur Seite kippen und die
Kassette anheben.
iDP-3410 User’s Manual
4.5
Einlegen der Papierrolle
1. Mit den Fingern in die Aussparungen an beiden Seiten der Druckerabdeckung greifen, und die Abdeckung
durch Anheben bis zum Anschlag öffnen.
2. Das Ende des Druckpapiers in nahezu rechtem Winkel abschneiden.
VORSICHT: • Ausschließlich das vorgeschriebene Druckpapier verwenden.
• Die Verwendung anderer Papiersorten kann zur Minderung der Druckqualität und zu
reduzierter Betriebslebensdauer des Druckers führen.
• Die Druckerabdeckung ist nicht abnehmbar und sollte deshalb nicht über den
Anschlag hinaus aufgeklappt werden.
• Beim Einführen des Druckpapiers darauf achten, daß das Papierende nicht zerknittert
oder geknickt ist.
3. Die Aufrollrichtung des Papiers prüfen.
4. Den Papierhalter öffnen und die Druckpapierrolle in der Mitte aufsetzen.
5. Den Drucker einschalten.
6. Das Papierende gerade in die Papiereinzugöffnung einführen (durch einen Pfeil an der Gehäusevorderseite
angezeigt).
7. Das Druckpapier wird automatisch in den Drucker eingezogen, bis das Papierende aus der
Papierauslauföffnung herauskommt.
8. Die Druckerabdeckung schließen und überschüssiges Papier an der Schneidklinge abreißen.
iDP-3410 User’s Manual
VORSICHT: • Schlaffes Druckpapier durch Zurückdrehen der Papierrolle straffen.
• Bei schräg eingesetztem Druckpapier den Papier-Freigabehebels drücken und das
Papier gerade richten.
• Die Druckerabdeckung niemals während des Druckens öffnen, da hierdurch
Papierstaus entstehen können.
iDP-3410 User’s Manual
4.6
Entfernen des restlichen Druckpapiers
1. Die Druckerabdeckung aufklappen.
2. Den Papier-Freigabehebel in Pfeilrichtung drücken und das Rollenpapier herausziehen.
VORSICHT: Beim Herausziehen des Druckpapiers (in Vorwärts- oder Rückwärtsrichtung) darauf achten,
den Papier-Freigabehebel zu betätigen.
4.7
Beseitigung von Papierstaus
1. Die Druckerabdeckung aufklappen.
2. Das Druckpapier vor der Papiereinzugöffnung sauber abschneiden.
3. Den Papier-Freigabehebel in Pfeilrichtung drücken. Hierdurch wird die Papiervorschubwalze
zurückgesetzt und das Papier freigegeben, so daß angestautes Papier beseitigt werden kann.
4. Sämtliche Papierreste aus dem Papierweg entfernen.
VORSICHT: • Beim Herausziehen des Druckpapiers (in Vorwärts- oder Rückwärtsrichtung) darauf
achten, den Papier-Freigabehebel zu betätigen.
iDP-3410 User’s Manual
4.8
Bedienfeld und Fehleranzeigelämpchen
1. Netzanzeigelämpchen (grün) (POWER)
Leuchtet bei eingeschalteter Netzversorgung.
2. Fehleranzeigelämpchen (rot) (ERROR)
Leuchtet, wenn das Papier aufgebraucht ist oder ein Fehler im Druckmechanismus oder in der
Kommunikations auftritt.
<Fehleranzeigen>
•Papierende:
Wenn sich das Papier dem Ende nähert, erkennt ein Sensor, der sich am Papierweg in
der Nähe des Druckkopfes befindet, das Papierende und schaltet das LEDFehleranzeigelämpchen ein. Durch Einschieben des Papiers in den Papierweg wird das
Papier eingezogen.
•Druckmechanismusfehler:
Wenn der Druckmechanismus aufgrund eines Papierstaus usw. anormal geladen ist,
leuchtet das LED-Fehleranzeigelämpchen auf, und der Druckbetrieb stoppt.
3. FEED-Taste
Durch Drücken der FEED-Taste wird das Papier kurzzeitig um jeweils eine Zeile vorgeschoben; bei
anhaltendem Drücken der Taste wird das Papier fortlaufend vorgeschoben.
4. FEED-Taste und Netzschalter
Zum Einschalten der Selbstdruckfunktion die FEED-Taste gedrückt halten und dabei gleichzeitig den
Drucker einschalten.
4.9
Betriebsfluß beim Einschalten
Einschalten
OFF
Feed SW
ON?
Pufferdaten
JA
"Pufferdaten löschen"
Ja (FEED SW) und
vergrößerter Rot-Druck
YES
NEIN
YES
OFF
1 Sek. vergangen
NO
NO
OFF
1 Sek. vergangen
iDP-3410 User’s Manual
ON
ON
NEIN
JA
5. DIP-SCHALTER-EINSTELLUNG
5.1
Lage der DIP-Schalter
(1) Betriebsstrom ausschalten.
(2) Ein Kassettenband entfernen. Die DIP-Schalter liegen, wie in der Abbildung gezeigt. (Nur DS1 für ParallelSchnittstelle vorhanden.)
iDP-3410 User’s Manual
5.2
DIP-Schalter-Einstellungen
1) DIP-Schalter 1
No.
Funktion
Automatische Schneideinheit
DS1-1
DS1-2
Internationale Zeichen
″
DS1-3
″
DS1-4
DS1-5
Verwendetes Papier
DS1-6
CR-Modus
DS1-7
Stellen
DS1-8
Puffergröße
DS1-9
Betriebsmodus
″
DS1-10
*1, *3 : Je nach Typ.
*2
: Je nach Bestimmungsort.
Internationale Zeichenwahl
No.
DS1-2
Land
ON
Ja
2P
1P
Siehe Tabelle unten
42 Stellen
40 Stellen
6 kB
256 Byte
Siehe Tabelle unten
DS1-3
DS1-4
ON
ON
ON
Frankreich
Dänemark
Schweden
Italien
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
Japan
OFF
OFF
OFF
Deutschland
Bei Auslieferung ab Werk
Siehe Tabelle unten
U.S.A.
Großbritannien
OFF
Nein
AUS
AUS *2
AUS *2
AUS *2
AUS
AUS
ON
ON
AUS *3
AUS *3
Zeichencode-Wahl
ESC/POSCBM-Modus
Modus
CBM
Code 437 (international)
Code 850
Code 850
″
″
″
″
″
″
″
″
″
″
CBM
Katakana
(japanisch)
Siehe internationale Zeichencode-Tabelle und Schriftzeichen-Tabelle
CR-Modus(DS1-6)
Modus
OFF
CBM
CR+LF
STAR
CR+LF
ESC/POS
CR+LF
ON
CR
Ignoriert
CR
Betriebsmodus DS1-9 DS1-10
CBM
OFF
ESC/POS
ON
STAR
OFF
STAR
ON
OFF
OFF
ON
ON
Star-Modus
Star
(international)
Code 850
″
″
″
″
″
Star
(japanisch)
iDP-3410 User’s Manual
2) DIP-Schalter 2
No.
Funktion
DS2-1
Bitlänge
DS2-2
Parität
DS2-3
Ungerade/Gerade
DS2-4
Kommunikationsmodus
DS2-5
Baudrate
″
DS2-6
″
DS2-7
DS2-8
Nicht verwendet
Baudrate
Baudrate
150
300
600
1200
2400
4800
9600
19200
DS2-5
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
8 Bit
Nein
Ungerade
DTR/DSR
OFF
7 Bit
Ja
Gerade
XON/XOFF
Siehe Tabelle unten
−
DS2-6
OFF
OFF
ON
ON
OFF
OFF
ON
ON
−
Werksseitige Einstellung
ON
ON
ON
ON
ON
ON
OFF
OFF
DS2-7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
hDer DIP-Schalter 2 wird nur für die serielle Schnittstelle verwendet.
(Hinweis)
Die Einstellung des verwendeten Papiers ändert einfach den Treiberimpuls für den
Druckkopf; sie bedeutet nicht, daß 2-Seiten-Papier nicht für die Einstellung 1P verfügbar ist.
Das gleiche gilt, wenn 1-Seiten-Papier für die Einstellung 2P verwendet wird.
iDP-3410 User’s Manual
6. EINSTELLUNG DER VORWAHL-JUMPERSTECKER
6.1
Lage der Vorwahl-Jumperstecker
(1) Betriebsstrom ausschalten.
(2) Ein Kassettenband entfernen.
(3) Die Oberabdeckung entfernen. Der Vorwahl-Jumperstecker liegt, wie in der Abbildung unten gezeigt.
Serielle Schnittstelle
6.2
Parallele Schnittstelle
Vorwahl-Jumperstecker-Tabelle
Seriell
Modus
Lage
SCA
SCB
SCC
SCD
SCE
SCF
SCG
SCH
CBM
STAR
ESC/POS
1-C *
1-C *
1-C
1-C
1-C *
1-C *
1-C *
1-C
2-C
1-C *
2-C
2-C
2-C
2-C
2-C
2-C *
2-C
2-C
*
*
1-C *
1-C *
1-C *
2-C *
CBM
STAR
ESC/POS
1-C *
1-C
1-C *
1-C
1-C
1-C
1-C *
1-C
2-C *
2-C
2-C
2-C *
* = Offen
1-C* = 1-C oder offen
2-C* = 2-C oder offen
Parallel
Modus
Lage
SCA
SCB
SCC
SCD
* = Offen
1-C* = 1-C oder offen
2-C* = 2-C oder offen
7. METHODE FÜR MODUSEINSTELLUNG
Dieser Drucker hat die Modi CBM, STAR und ESC/POS. Jeder gewünschte Modus kann gewählt und nach
Bedarf eingestellt werden.
(1) Einstellmethode
• Siehe 5. DIP-SCHALTER-EINSTELLUNG
• Unter bezug auf die Einstellungen der DIP-Schalter-Segmente 1-9 und 1-10 und die der VorwahlJumperstecker jeden Modus einstellen.
iDP-3410 User’s Manual
12. WARTUNG UND DIENST
Bitte wenden Sie sich an die folgenden Stellen für weitergehende Informationen.
Nordamerika
CBM America Corporation
Service Center
365 Van Ness Way
Suite 510
Torrance, CA 90501, USA
Andere Gebiete
Japan CBM Corporation
Information Systems Division
CBM Bldg., 5-68-10, Nakano
Nakano-ku, Tokyo 164-0001
Japan
TEL +1-310-781-1460
FAX +1-310-781-9157
TEL +81-3-5345-7540
FAX +81-3-5345-7541