User manual | ADTRAN 1202076L1 Cordless Telephone User Manual

TSU 600
&
TSU 600e
User Manual
Part Numbers
1202076L1
1202076L1#DC
1202076L2
1202076L2#DC
October 1998
61202076L1-1C
Trademarks:
Windows is a registered trademark of Microsoft Corp.
T-Watch is a trademark of ADTRAN, Inc.
SLC96 is a registered trademark of AT&T
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: (256) 963-8000
© 1998 ADTRAN, Inc.
All rights reserved.
Printed in USA.
YEAR 2000 Compliance
All ADTRAN transmission hardware and software products have been tested
and found to be fully compliant with the YEAR 2000 requirements. This is true
for all models and revisions regardless of the date of manufacture or delivery.
Users who wish to independently verify that specific products are in compliance may contact ADTRAN Technical Support at 1-888-423-8726 for additional
information
FCC REGULATIONS REQUIRE THAT THE FOLLOWING INFORMATION BE
PROVIDED TO THE CUSTOMER IN THIS MANUAL
1. This equipment complies with Part 68 of the FCC rules. The required
label is attached to the bottom of the chassis.
2. An FCC compliant telephone cord and modular plug is provided
with this equipment. This equipment is designed to be connected to
the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for
details.
3. If your Product causes harm to the telephone network, the Telephone
Company may discontinue your service temporarily. If possible,
they will notify you in advance. If advance notice is not practical, you
will be notified as soon as possible. You will be advised of your right
to file a complaint with the FCC.
4. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. If they do, you will be given advance notice
so as to give you an opportunity to maintain uninterrupted service.
5. If you experience trouble with the equipment Product, please contact
ADTRAN at (256) 963-8000 for repair/warranty information. The
telephone company may ask you to disconnect this equipment from
the network until the problem has been corrected, or until you are
sure the equipment is not malfunctioning.
6. This unit contains no user serviceable parts.
7. The following information may be required when applying to your
local telephone company for leased line facilities.
Service Type
REN/SOC
FIC
USOC
1.544 Mbps -SF
6.0N
04DU9-BN
RJ-48C
1.544 Mbps - SF and B8ZS
6.0N
04DU9-DN
RJ-48C
1.544 Mbps - ESF
6.0N
04DU9-1KN
RJ-48C
1.544 Mbps - ESF and B8ZS
6.0N
04DU9-1SN
RJ-48C
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio frequencies. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his
own expense.
Shielded cables must be used with this unit to ensure compliance with
Class A FCC limits.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus as set out in the interference-causing
equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Class A prescrites dans la norme
sur le materiel brouilleur: “Appareils Numeriques,” NMB-003 edictee
par le ministre des Communications.
CANADIAN EQUIPMENT LIMITATIONS
The Industry Canada Certification label identifies certified equipment.
This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements.
The Department does not guarantee the equipment will operate to the
user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method
of connection. In some cases, the company's inside wiring associated
with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
waterpipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or an electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is
used by the device, to prevent overloading. The termination on a loop
may consist of any combination of devices subject only to the equipment
that the total of the LNs of all devices does not exceed 100.
The ringer equivalence number (REN) assigned to each terminal adapter is used to determine the total number of devices that may be connected to each circuit. The sum of the RENs from all devices in the circuit
should not exceed a total of 5.0.
AFFIDAVIT REQUIREMENTS FOR CONNECTION
TO DIGITAL SERVICES
• An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and
billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into
voiceband analog signals and transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or
billing information is being transmitted or that the output of the device meets Part 68 encoded analog content or billing protection specifications.
• End user/customer will be responsible to file an affidavit with the local exchange carrier when connecting unprotected CPE to a 1.544
Mbps or subrate digital services.
• Until such time as subrate digital terminal equipment is registered for
voice applications, the affidavit requirement for subrate services is
waived.
AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES
EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES
For the work to be performed in the certified territory of
______________________________(telco name)
State of _________________________________
County of ________________________________
I, ___________________________________ (name),
(business address), ______________________ (telephone number) being
duly sworn, state:
I have responsibility for the operation and maintenance of the terminal
equipment to be connected to 1.544 Mbps and/or ________ subrate digital services. The terminal equipment to be connected complies with
Part 68 of the FCC rules except for the encoded analog content and billing protection specifications. With respect to encoded analog content
and billing protection:
( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to analog content and encoded billing protection information continuously complies
with Part 68 of the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded
analog content or billing information which is intended to be decoded
within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and
is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible
for the establishment, maintenance, and adjustment of the encoded analog content and billing information has (have) been trained to perform
these functions by successfully having completed one of the following
(check appropriate blocks):
( ) A. A training course provided by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) B. A training course provided by the customer or authorized representative, using training materials and instructions provided by the
manufacturer/grantee of the equipment used to encode analog signals;
or
( ) C. An independent training course (e.g., trade school or technical
institution) recognized by the manufacturer/grantee of the equipment
used to encode analog signals; or
( ) D. In lieu of the preceding training requirements, the operator(s)/
maintainer(s) is (are) under the control of a supervisor trained in accordance with _________ (circle one) above.
I agree to provide _________________ (telco's name) with proper documentation to demonstrate compliance with the information as provided
in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of ________, 199___
_________________________________
Notary Public
My commission expires:
_________________________________
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, please follow these basic safety
precautions to reduce the risk of fire, electrical shock, or personal injury:
1 Do not use this product near water, such as near a bath tub,
wash bowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool.
2 Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote risk of shock from
lightning.
3 Do not use the telephone to report a gas leak in the vicinity
of the leak.
4 Use only the power cord, power supply, and/or batteries
indicated in the manual. Do not dispose of batteries in a
fire. They may explode. Check with local codes for special
disposal instructions.
Warranty and Customer Service
ADTRAN will replace or repair this product within five years from the
date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information refer to the ADTRAN Equipment Warranty and Repair
and Return Policy Procedure.
Return Material Authorization (RMA) is required prior to returning
equipment to ADTRAN.
For Service, RMA requests, or more information, contact ADTRAN Customer Service listed on the inside back cover of this manual.
Table of Contents
Chapter 1 Introduction .......................................................................................... 1-1
TSU 600 Overview .................................................................................................... 1-1
Product Description .......................................................................................... 1-1
Standard Features in the TSU 600................................................................... 1-2
TSU Option Modules ........................................................................................ 1-3
Option Module Architecture ........................................................................... 1-4
TSU 600 Configuration Applications .................................................................... 1-5
Router, PBX, Video Conferencing Application............................................. 1-5
Drop and Insert, Voice, and Router Application.......................................... 1-6
Chapter 2 Installation ............................................................................................ 2-1
Unpack, Inspect, Power Up .................................................................................... 2-1
Receipt Inspection ............................................................................................. 2-1
ADTRAN Shipments Include.......................................................................... 2-1
Customer Provides............................................................................................ 2-1
Power Connection ............................................................................................. 2-2
DC Powered Units ..................................................................................... 2-2
Backup Power Supply (600e only) ........................................................... 2-2
Installing and Replacing the Power Supply ................................... 2-3
Grounding Instructions ........................................................................................... 2-4
Identification of Rear Panel Layout ....................................................................... 2-5
TSU 600 Interfaces............................................................................................. 2-9
Network Interface ...................................................................................... 2-9
Network Test Interface .............................................................................. 2-9
Control Port Input ...................................................................................... 2-9
Chain Port Output ..................................................................................... 2-9
10BaseT Interface (600e only) ................................................................. 2-10
Option Slot Arrangement............................................................................... 2-10
Power-up Testing ............................................................................................ 2-11
Self-Test ..................................................................................................... 2-11
Board level tests ................................................................................ 2-12
Unit level tests ................................................................................... 2-12
Initialization ..................................................................................................... 2-12
61202076L1-1
TSU 600 User Manual
i
Table of Contents
Set User Passcode ..................................................................................... 2-12
Set Unit Identification .............................................................................. 2-12
Set Control Port ........................................................................................ 2-13
Chain-In (PC) ............................................................................................2-13
Chain In/Chain Out ................................................................................2-13
Normal Power-Up Procedure........................................................................ 2-14
Chapter 3 Operation ............................................................................................... 3-1
Front Panel ................................................................................................................. 3-1
CSU Status LEDs ............................................................................................... 3-2
Module Status LEDs ......................................................................................... 3-3
Operation Keys .................................................................................................. 3-5
General Menu Operation .......................................................................... 3-5
Selecting and Activating a Menu Item .................................................... 3-6
Editing the Data Field ................................................................................ 3-7
Display Only Data Fields .......................................................................... 3-8
Exit Any Menu Field Operation Or Display .......................................... 3-8
Data Port Identification .................................................................................... 3-9
Front Panel Menu Structure........................................................................... 3-10
Alternate Methods of Control........................................................................ 3-11
T-Watch PRO (ADTRAN PC Program) ................................................3-11
T-Watch PRO/LAN Connection .................................................... 3-11
T-Watch PRO/EIA-232 Connection ............................................... 3-12
SNMP ......................................................................................................... 3-12
Terminal Mode Connection .................................................................... 3-13
Telnet Connection .................................................................................... 3-13
Chapter 4 Status Menu .......................................................................................... 4-1
Network Performance Reports (NI PERF RPTS) ..........................................
Network Interface Errors (NI ERRORS) ........................................................
Active Alarms ....................................................................................................
View History ......................................................................................................
Port Status...........................................................................................................
Remote Port ........................................................................................................
Clear Port Alarm................................................................................................
ENET Status (600e only) ...................................................................................
PS Status (600e only) .........................................................................................
4-2
4-3
4-4
4-4
4-5
4-5
4-5
4-6
4-6
Chapter 5 Configuration Menu ............................................................................ 5-1
Network (NI) ............................................................................................................. 5-2
Network (NI) Menu Items ............................................................................... 5-2
TSU 600 Clock Sources ..................................................................................... 5-4
Network Timing .........................................................................................5-4
DTE Timing ................................................................................................. 5-5
U-BR1TE (Slot 1) .........................................................................................5-5
ii
TSU 600 User Manual
61202076L1-1
Table of Contents
Internal Timing ........................................................................................... 5-6
Secondary Timing ...................................................................................... 5-7
Normal (CSU) Timing ............................................................................... 5-8
Unit Menu .......................................................................................................... 5-9
Map Exchange (Map Xchng) Menu ............................................................. 5-11
MAP In Use: A(B) Menu ............................................................................... 5-11
DS0 Map A and DS0 Map B Menu .............................................................. 5-12
Create Temp Example ............................................................................. 5-13
Port Configuration (Port Config) ................................................................. 5-15
Chapter 6 Utility Menu ......................................................................................... 6-1
Time/Date .......................................................................................................... 6-2
Factory Restore .................................................................................................. 6-2
Set Passcode ....................................................................................................... 6-2
Enter Passcode from Other Menus .......................................................... 6-2
Change/Set a Passcode ............................................................................. 6-3
Automatic Time-out Feature .................................................................... 6-3
No Passcode Desired ................................................................................. 6-3
Unit ID ................................................................................................................ 6-3
Setting the Unit Identification .................................................................. 6-4
No Unit ID Desired .................................................................................... 6-4
Software Revision (Software Rev) .................................................................. 6-4
Port Utility.......................................................................................................... 6-4
ENET Address (600e only)............................................................................... 6-4
CMD Mode......................................................................................................... 6-4
Chapter 7 Test Menu .............................................................................................. 7-1
Network Tests.................................................................................................... 7-2
Loopback Tests ........................................................................................... 7-2
Network Interface Loopbacks........................................................... 7-3
Local Loopbck.................................................................................................... 7-3
Remote Loopbk.................................................................................................. 7-4
Test Pattern ....................................................................................................... 7-5
QRSS Pattern ............................................................................................... 7-5
Pattern Result..................................................................................................... 7-6
Run Self-Test ...................................................................................................... 7-7
Board level tests ......................................................................................... 7-7
Unit level tests ............................................................................................ 7-7
Port Tests ............................................................................................................ 7-8
Cancel Tests........................................................................................................ 7-8
Chapter 8 Telnet/Terminal Menus ...................................................................... 8-1
Main Menu ................................................................................................................ 8-1
Status, Config, Util, and Test Menu Options ................................................ 8-2
DS0 Maps Configuration Menu ............................................................... 8-2
61202076L1-1
TSU 600 User Manual
iii
Table of Contents
Initializing the Temp Map ................................................................. 8-3
Editing the Temp Map ....................................................................... 8-4
Applying the Temp Map ................................................................... 8-4
Reviewing Maps.................................................................................. 8-4
Remote Menu Access ........................................................................................ 8-5
Management Configuration............................................................................. 8-5
Unit Access Table ....................................................................................... 8-5
Add New Unit ..................................................................................... 8-6
Modify Unit ......................................................................................... 8-6
Delete Unit ........................................................................................... 8-6
Default Unit Passcode ........................................................................ 8-7
OK ......................................................................................................... 8-7
SNMP Read Community.................................................................................. 8-7
SNMP Read/Write Community .............................................................. 8-7
SNMP Trap Community ........................................................................... 8-8
System Name ..............................................................................................8-8
System Contact ........................................................................................... 8-8
System Location .......................................................................................... 8-8
Auto. Fail Traps Sent ................................................................................. 8-9
Poll Link Status Traps Sent ....................................................................... 8-9
Ping IP Host ................................................................................................ 8-9
Telnet/Terminal Time-out ........................................................................8-9
Telnet/Terminal Password ....................................................................... 8-9
Exit ................................................................................................................ 8-9
Flash Download................................................................................................. 8-9
Quit Session........................................................................................................ 8-9
Appendix A Understanding SNMP ................................................................... A-1
Appendix B Understanding TR-08..................................................................... B-1
Appendix C Network Pinouts............................................................................. C-1
Appendix D System Messages............................................................................ D-1
Appendix E Specifications.................................................................................... E-1
Index....................................................................................................................Index-1
iv
TSU 600 User Manual
61202076L1-1
List of Figures
Figure 1-1. TSU 600 Option Modules ................................................................... 1-4
Figure 1-2. Router, PBX, Video Conferencing Application Set Up .................. 1-5
Figure 1-3. Drop and Insert, Voice, and Router Application Set Up ............... 1-6
Figure 2-1a. TSU 600 Rear Panel ............................................................................ 2-5
Figure 2-1b. TSU 600 with DC Power Rear Panel............................................... 2-6
Figure 2-1c. TSU 600e Rear Panel.......................................................................... 2-7
Figure 2-1d. TSU 600e with DC Power Rear Panel............................................. 2-8
Figure 2-2. TSU 600 Interfaces ............................................................................... 2-9
Figure 2-3. TSU 600 Slot Designation (Rear View) ........................................... 2-10
Figure 2-4. Example of Chain In.......................................................................... 2-13
Figure 3-1. TSU 600 Front Panel Layout .............................................................. 3-4
Figure 3-2. Example of Basic Front Panel Menu Travel..................................... 3-6
Figure 3-3. Display and Data Fields...................................................................... 3-8
Figure 3-4. Module Slots, TSU 600 ........................................................................ 3-9
Figure 4-1. Complete Status Menu........................................................................ 4-1
Figure 4-2. Network Interface Performance Report ........................................... 4-2
Figure 4-3. Display of Alarm Messages ............................................................... 4-4
Figure 5-1. Configuration Menu............................................................................ 5-1
Figure 5-2. Network Timed Clock Source............................................................ 5-4
Figure 5-3. DTE Timed Clock Source ................................................................... 5-5
Figure 5-4. Internal Clock Source .......................................................................... 5-6
Figure 5-5. Secondary Clock Source ..................................................................... 5-7
Figure 5-6. Normal (CSU)....................................................................................... 5-8
Figure 5-7. DS0 Map Designations...................................................................... 5-12
Figure 5-8. Create Temp Selection Screen.......................................................... 5-14
Figure 6-1. Utility Menu Tree ................................................................................ 6-1
Figure 7-1. Test Menu ............................................................................................. 7-1
Figure 7-2. Network Loopback Tests.................................................................... 7-3
Figure 8-1. Telnet/Terminal Main Menu............................................................. 8-1
Figure 8-2. DS0 Temp Map .................................................................................... 8-2
Figure 8-3. Unit Access Table ................................................................................ 8-6
61202076L1-1
TSU 600 User Manual
v
List of Figures
vi
TSU 600 User Manual
61202076L1-1
List of Tables
Table B-1.
Table B-2.
Table C-1.
Table C-2.
Table C-3.
Table C-4.
61202076L1-1
Alarm Conditions ................................................................................. B-2
TR-08 DS0 Conversion Table .............................................................. B-3
Network Pinouts.................................................................................. C-1
Control In/Chain In Pinout ............................................................... C-2
Chain-Out Pinout ................................................................................ C-3
10BaseT Ethernet ................................................................................. C-4
TSU 600 User Manual
vii
List of Tables
viii
TSU 600 User Manual
61202076L1-1
Introduction
Chapter 1
TSU 600 OVERVIEW
This manual covers the use of the following products:
•
•
•
•
TSU 600
TSU 600 with DC power
TSU 600e
TSU 600e with DC power
Unless otherwise stated, the TSU 600 refers to all four products.
Product Description
The TSU 600 is a T1/FT1 multiplexer with six option slots and embedded SNMP management. The TSU 600’s six option slots accept one of
many available option modules for voice and data applications. Each
module offers up to four ports for a total of 24 possible voice or data
ports.
The TSU 600 serves as the link between user data sources such as:
•
•
•
•
•
•
local area network (LAN) bridges
routers,
computers,
CAD systems,
teleconferencing equipment, and
PBXs.
Through the use of multiple data ports, the TSU 600 can simultaneously
connect one or more of these devices to a T1 circuit. The amount of
bandwidth allocated to each port is custom-programmable. You can
manually allocate bandwidth or set the bandwidth to change automatically at predetermined times to use the available bandwidth most advantageously.
61202076L1-1
TSU 600 User Manual
1-1
Chapter 1. Introduction
Changes in the configuration do not disrupt data flow in channels that
are not being reconfigured. The unique architecture and the availability
of option modules provides a path for growth to accommodate future
requirements.
The TSU 600 offers a wide variety of network management options. You
can manage via SNMP through the 10BaseT (600e only) or chain-in
ports. If you are using T-Watch PRO, a Microsoft Windows® program,
you can manage the TSU 600 via the same 10BaseT (600e only) or chainin ports. An enhanced VT-100 terminal interface is also provided.
Standard Features in the TSU 600
The standard features of the TSU 600 are listed below:
• A single T1 interface
• Six slots to house option modules with up to four additional data
ports, including voice
• Architecture that allows mix of port types to meet the data interface
requirements
• Easy configuration capabilities using simplistic menus displayed in a
liquid crystal display (LCD) window operated by a front panel keypad
• SNMP, Telnet, and T-Watch PRO management via SLIP or 10BaseT
(600e only)
• Ability to proxy for “agentless” units
• Enhanced terminal mode
• Support for a redundant AC power supply (600e only)
• Two programmable configuration maps that define the bandwidth
allocation between data ports
• Data drop and insert, as well as full drop and insert
• Flash memory for software updates
• Timing selectable from the network, from the slot 1 data port, internally, or from a secondary interface
• QRSS; 511 test patterns using Nx option
• Fractional T1 loopbacks as defined in annex B of ANSI T1.403-1995
• Extensive self-testing and monitoring to ensure proper operation
1-2
TSU 600 User Manual
61202076L1-1
Chapter 1. Introduction
TSU Option Modules
Module Name
Description
DSX1
Short haul T1 interface for operation with a
PBX (Terminal Interface).
Full Drop and Insert
Permits the dropping of data and insertion of
new data into the same DS0 time slot. This
module includes a long haul DS1 interface. It
can also be used as a second DS1 interface to
provide up to 3 MB aggregate throughput.
Nx56/64 Serial Interface Provides a V.35 serial interface in either single or dual versions.
NxIQ
Frame-relay aware device that provides
detailed information regarding the health
and performance of the frame relay circuit.
Voice Interface
2/4 channel FXS/FX0/E&M.
OCU DP
Interfaces to DDS or 4-wire Switched-56.
DSU DP
Provides two sync or async ports (232 or
V.35).
Dial Backup
Allows for backup of data upon network T1
failure.
U-BR1TE
Allows ISDN lines to be extended over a T1
line.
61202076L1-1
TSU 600 User Manual
1-3
Chapter 1. Introduction
Option Module Architecture
The TSU 600 features a unique architecture that allows the addition of
six option modules and plug-on boards, providing an opportunity for
growth to accommodate many applications. See Figure 1-1. This unique
approach allows you to mix interface types to meet any application.
TSU 600
DSX-1
Module
OCU-DP
Module
Plug on
V.35
V.35
Module
Plug on
OCU DP
D&I
Module
DUAL
Voice
Plug on
Dual Voice
Figure 1-1. TSU 600 Option Modules
1-4
TSU 600 User Manual
61202076L1-1
Chapter 1. Introduction
TSU 600 CONFIGURATION APPLICATIONS
The following examples illustrate possible configurations of TSU 600
applications.
Router, PBX, Video Conferencing Application
In this application, an Nx54/64 module provides a V.35 interface to a
router. The PBX is interfaced to the TSU 600 with the DSX-1 module. An
OCU DP module and OCU DP plug-on board provide two switched 56
circuits for video conferencing. The SLIP port or 10BaseT port (600e
only) allows SNMP network management over the LAN. See Figure 1-2.
PBX
TSU 600
ROUTER
SLIP or 10BaseT (600e only)
VIDEO
CONFERENCING
SNMP NETWORK
MANAGEMENT WORKSTATION
Figure 1-2. Router, PBX, Video Conferencing Application Set Up
61202076L1-1
TSU 600 User Manual
1-5
Chapter 1. Introduction
Drop and Insert, Voice, and Router Application
The TSU 600 provides a router interface with an Nx56/64 module. A
drop and insert module provides a second T1 interface to a remote TSU.
T-WATCH PRO (which runs on a PC) easily manages the network. FXO
modules are used to provide PBX extensions to remote sites. See Figure
1-3.
TSU 100
A
ENTER
B
1
OK
TEST
ALARM
COPY
*
3
E
5
ALARM
8
7
CANCEL
DSU
C
2
D
4
REMOTE
0
HOME
0
F
6
CLEAR
9
SHIFT
#
MODULE
OK TEST
ALARM
CSU
OK TEST
ERROR
ALARM
ROUTER
ROUTER
T-WATCH
PBX
Figure 1-3. Drop and Insert, Voice, and Router Application
Set Up
1-6
TSU 600 User Manual
61202076L1-1
Installation
Chapter 2
UNPACK, INSPECT, POWER UP
Receipt Inspection
Carefully inspect the TSU 600 for shipping damages. If you suspect
damage, file a claim immediately with the carrier and then contact ADTRAN Customer Service (see the inside last page of this manual). If possible, keep the original shipping container for use in shipping the TSU
600 back for repair or for verification of damage during shipment.
ADTRAN Shipments Include
• The TSU 600
• A line interface cable: an 8-position modular to
8-position modular (15 ft.)
• A DB-25 to modular adapter
• An 8-position, 6-foot modular cable for the
Chain-In port connection
• The User Manual
• Rackmount Brackets
• Rackmount Data Sheet
Customer Provides
• Cables for any expansion modules to be used with the TSU 600
• 10BaseT cable for connection to a LAN or router (if you plan to use
remote management features). This is for 600e only.
61202076L1-1
TSU 600 User Manual
2-1
Chapter 2. Installation
Power Connection
The AC- powered TSU 600 is equipped with a captive, 8-foot power
cord, terminated by a 3-prong plug which connects to a grounded power receptacle.
Power to the TSU 600 must be from a grounded 90-120 VAC, 50/
60Hz source.
DC Powered Units
The DC-powered TSU 600 (1202076L1#DC or 1202076L2#DC) is
equipped with a terminal strip on the rear of the unit. The power source
should be connected to the terminal strip according to the polarity markings on the unit.
Example:
A -48V source would be connected with the -48V return attached to the
(+) terminal and the -48VDC attached to the (-) terminal. Power must be
from a DC source in the range of 21 to 26 VDC or in the range of 40 to
56VDC.
The protective cover should be reinstalled over the terminal strip once
the power source is connected.
The DC-powered TSU 600 is to be installed only in restricted areas (dedicated equipment rooms, equipment closets, etc.) in accordance with Articles 110-16 and 110-18 of the National Electric Code, ANSI/NFPA 70.
Backup Power Supply (600e only)
The TSU 600e has two power supply slots on the right side of the chassis.
The base unit is shipped with a single power supply. The TSU 600e is
fully operational with only a single power supply, which may be installed on either the left (power supply A) or the right (power supply B).
You can install a backup supply in the unused slot. The red System
Alarm LED on the front panel will indicate failure of either supply.
2-2
TSU 600 User Manual
61202076L1-1
Chapter 2. Installation
Installing and Replacing the Power Supply
The following steps show how to install a new supply or replace a failed
supply.
Power does not have to be turned off on a working supply to add a new supply
or replace a failed one.
Step
1
Action
One Power Supply
If only one supply is installed in the chassis, remove the
blank panel covering the unused power supply slot.
Two Power Supplies
If two power supplies are installed, the failed supply can be
identified by the alarm on the front panel LCD. The alarm
message will identify a failure on Power Supply A or Power
Supply B. The option slot legend on the rear panel shows the
location of each power supply. Turn the power switch to Off
on the failed supply and unplug the power cord from the
power source.
61202076L1-1
2
Remove the two screws that secure the power supply module to the TSU 600e chassis and remove the failed power supply module.
3
Remove the new power supply from the shipping container. Make sure the power switch is in the Off position.
4
Plug the new supply into the open power supply slot and
install the two screws on the power supply module
5
Plug the new power supply cord into a grounded 115 VAC,
50/60 Hz power receptable.
6
Turn the power switch On.
TSU 600 User Manual
2-3
Chapter 2. Installation
GROUNDING INSTRUCTIONS
The grounding instruction information is from the Underwriters' Laboratory UL 1950, 3rd Edition.
An equipment grounding conductor that is not smaller in size than the
ungrounded branch-circuit supply conductors is to be installed as part
of the circuit that supplies the product or system.
• Bare, covered, or insulated grounding conductors are acceptable.
• Individually covered or insulated equipment grounding conductors
shall have a continuous outer finish that is either green, or green with
one or more yellow stripes.
• The equipment grounding conductor is to be connected to ground at
the service equipment.
• The attachment-plug receptacles in the vicinity of the product or system are all to be of a grounding type.
• The equipment grounding conductors serving these receptacles are
to be connected to earth ground at the service equipment.
• A supplementary equipment grounding conductor shall be installed
between the product or system and ground that is in addition to the
equipment grounding conductor in the power-supply cord.
• The supplementary equipment grounding conductor shall not be
smaller in size than the ungrounded branch-circuit supply conductors.
• The supplementary equipment grounding conductor shall be connected to the product at the terminal provided, and shall be connected to ground in a manner that will retain the ground connection
when the product is unplugged from the receptacle.
• The connection to ground of the supplementary equipment grounding conductor shall be in compliance with the rules for terminating
bonding jumpers at Part K or Article 250 of the National Electrical
Code, ANSI/NFPA 70.
• Termination of the supplementary equipment grounding conductor
is permitted to be made to building steel, to a metal electrical raceway
system, or to any grounded item that is permanently and reliably
connected to the electrical service equipment ground.
• The supplemental grounding conductor shall be connected to the
equipment using a number 8 ring terminal.
• The terminal should be fastened to the grounding lug provided on
the rear panel of the equipment.
• The ring terminal should be installed using the appropriate crimping
tool (AMP P/N 59250 T-EAD Crimping Tool or equivalent).
2-4
TSU 600 User Manual
61202076L1-1
Chapter 2. Installation
IDENTIFICATION OF REAR PANEL LAYOUT
Figures 2-1a, Figure 2-1b, Figure 2-1c, and Figure 2-1d show the configuration for the rear panels of the TSU 600, TSU 600 with DC Power, TSU
600e, and TSU 600e with DC power.
1
3
2
CAUTION-RISK OF
ELECTRIC SHOCK
CAUTION:
MAINTENANCE TO BE
PERFORMED BY TRAINED
SERVICE PERSONEL ONLY
SUPPLEMENTAL EARTH GROUND MUST BE
CONNECTED PRIOR TO CONNECTION OF
TELECOMMUNICATION WIRING.
IN OUT MON
NETWORK
CONTROL
/CHAIN
IN
10 BASE T
ALL EMPTY SLOTS MUST BE
COVERED WITH BLANK PANELS
OUT
4
MODULE 1
MODULE 4
MODULE 2
MODULE 5
P
W
R
P
W
R
MODULE 3
MODULE 6
A
B
I
SEE MANUAL BEFORE
REMOVING POWER SUPPLY
(600e ONLY)
O
PORT X.1
NX 56/64
PORT X.1
NX 56/64
PORT X.2
V.35
PORT X.2
DUAL
FXS
DUAL
FXS
PORT X.3
V.35
PORT X.3
1A/250V
PORT X.4
90-130 VAC
60 HZ
.7A MAX
IN OUT MON
SEC. NI
PORT X.1
NX 56/64
PORT X.2
DS-1
CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE AND RATING
OF FUSE
V.35
8
6
5
1
T1 Monitor/Test Jacks
2
T1 Network Connection
3
Control In/Out Connection
4
Power Switch
5
Blank panel covering an unused option slot
6
Example of option modules installed
7
Power Cord
8
1A/250V Fuse
7
Figure 2-1a. TSU 600 Rear Panel
61202076L1-1
TSU 600 User Manual
2-5
Chapter 2. Installation
1
CAUTION-RISK OF
ELECTRIC SHOCK
CAUTION:
MAINTENANCE TO BE
PERFORMED BY TRAINED
SERVICE PERSONEL ONLY
SUPPLEMENTAL EARTH GROUND MUST BE
CONNECTED PRIOR TO CONNECTION OF
TELECOMMUNICATION WIRING.
IN OUT MON
NETWORK
4
3
2
ALL EMPTY SLOTS MUST BE
COVERED WITH BLANK PANELS
CONTROL
/CHAIN
10 BASE T
IN
OUT
MODULE 1
MODULE 4
MODULE 2
MODULE 5
P
W
R
P
W
R
MODULE 3
MODULE 6
A
B
I
SEE MANUAL BEFORE
REMOVING POWER SUPPLY
(600e ONLY)
O
PORT X.1
NX 56/64
PORT X.1
NX 56/64
PORT X.2
V.35
PORT X.2
DUAL
FXS
DUAL
FXS
PORT X.3
V.35
PORT X.3
5A/250V
PORT X.4
24/48 VDC
+
IN OUT MON
SEC. NI
PORT X.1
NX 56/64
PORT X.2
DS-1
-
CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE AND RATING
OF FUSE.
V.35
8
5
6
1
T1 Monitor/Test Jacks
2
T1 Network Connection
3
Control In/Out Connection
4
Power Switch
5
Blank panel covering an unused option slot
6
Example of option modules installed
7
Power Input Terminals
8
5A/250V Fuse
7
Figure 2-1b. TSU 600 with DC Power Rear Panel
2-6
TSU 600 User Manual
61202076L1-1
Chapter 2. Installation
3
2
1
CAUTION-RISK OF
ELECTRIC SHOCK
CAUTION:
MAINTENANCE TO BE
PERFORMED BY TRAINED
SERVICE PERSONEL ONLY
SUPPLEMENTAL EARTH GROUND MUST BE
CONNECTED PRIOR TO CONNECTION OF
TELECOMMUNICATION WIRING.
IN OUT MON
NETWORK
ALL EMPTY SLOTS MUST BE
COVERED WITH BLANK PANELS
4
CONTROL
/CHAIN
IN
10 BASE T
OUT
5
MODULE 1
MODULE 4
MODULE 2
MODULE 5
P
W
R
P
W
R
MODULE 3
MODULE 6
A
B
SEE MANUAL BEFORE
REMOVING POWER SUPPLY
O
PORT X.1
NX 56/64
PORT X.1
NX 56/64
PORT X.2
V.35
SEE MANUAL BEFORE
REMOVING POWER SUPPLY
(600e ONLY)
PORT X.2
DUAL
FXS
DUAL
FXS
PORT X.3
V.35
I
O
I
PORT X.3
PORT X.4
90-120 VAC
50/60 HZ.
.7A MAX
IN OUT MON
SEC. NI
PORT X.1
90-120 VAC
50/60 HZ.
.7A MAX
NX 56/64
PORT X.2
DS-1
V.35
7
8
6
1
T1 Monitor/Test Jacks
2
T1 Network Connection
3
10BaseT Connection
4
Control In/Out Connection
5
Power Switch
6
Blank panel covering an unused option slot
7
Example of option modules installed
8
Power Supply B (if installed)
Figure 2-1c. TSU 600e Rear Panel
61202076L1-1
TSU 600 User Manual
2-7
Chapter 2. Installation
1
CAUTION-RISK OF
ELECTRIC SHOCK
CAUTION:
MAINTENANCE TO BE
PERFORMED BY TRAINED
SERVICE PERSONEL ONLY
SUPPLEMENTAL EARTH GROUND MUST BE
CONNECTED PRIOR TO CONNECTION OF
TELECOMMUNICATION WIRING.
IN OUT MON
NETWORK
5
3
2
ALL EMPTY SLOTS MUST BE
COVERED WITH BLANK PANELS
4
CONTROL
/CHAIN
IN
10 BASE T
OUT
6
MODULE 1
MODULE 4
MODULE 2
MODULE 5
MODULE 3
MODULE 6
P
W
R
P
W
R
A
B
I
SEE MANUAL BEFORE
REMOVING POWER SUPPLY
(600e ONLY)
O
PORT X.1
NX 56/64
PORT X.1
NX 56/64
PORT X.2
V.35
DUAL
FXS
PORT X.2
DUAL
FXS
PORT X.3
V.35
PORT X.3
5A/250V
PORT X.4
24/48 HZ.
+
IN OUT MON
SEC. NI
PORT X.1
NX 56/64
PORT X.2
DS-1
-
CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE AND RATING
OF FUSE.
V.35
9
8
7
1
T1 Monitor/Test Jacks
2
T1 Network Connection
3
10BaseT Connection
4
Control In/Out Connection
5
Power Switch
6
5A/250V Fuse
7
Blank panel covering an unused option slot
8
Example of option modules installed
9
Power Input Terminals
Figure 2-1d. TSU 600e with DC Power Rear Panel
2-8
TSU 600 User Manual
61202076L1-1
Chapter 2. Installation
TSU 600 Interfaces
The TSU 600 is equipped with six option slots, management interfaces,
and a T1 interface, in the rear panel. See Figure 2-2.
LAN
PC or Modem
Control 10BaseT Chain
Input (600e only) Output
NI
TSU 600
Chain
Input
Chain
Output
NI TSU 600
Option
Network
Figure 2-2. TSU 600 Interfaces
Network Interface
The network interface (NI) port provides the connection to the T1. This
port complies with the applicable ANSI and AT&T standards. For more
information, see Wiring on page B-1.
Network Test Interface
The IN and OUT test jacks for the network interface provide intrusive
test capability for the incoming T1. By connecting to these jacks with test
equipment, the T1 connection will be broken, and the test equipment
will terminate the incoming T1. The MON test jack provides a bridged
access jack for non-intrusive monitoring of the incoming T1. When connected to this jack, the test equipment should be configured for a
bridged termination.
Control Port Input
The control port input provides an EIA-232 input from a PC or a modem
for control of the TSU 600. You can also use it as a chain input from another TSU 600 or TSU 100. For more information, see Wiring on page C1.
Chain Port Output
The chain port output provides an EIA-232 output to chain control to
other TSUs. For more information, see Wiring on page C-1.
61202076L1-1
TSU 600 User Manual
2-9
Chapter 2. Installation
10BaseT Interface (600e only)
The 10BaseT interface provides the LAN interface for managing the TSU
600e with SNMP or T-watch PRO. For more information, see Wiring on
page C-1.
Option Slot Arrangement
As viewed from the rear of the TSU 600, the slots are numbered as
shown in Figure 2-3. All slots are functionally identical except slots one,
two, and six. These slots offer additional functions.
SLOT 4
DTE TIMING
SLOT 2
SLOT 5
DIAL BACKUP
SLOT 3
POWER SUPPLY
SLOT 1
SLOT 6
SECONDARY INTERFACE
DSX-1; FULL D&I
Figure 2-3. TSU 600 Slot Designation (Rear View)
2-10
Slot 1
Slot 1 is used as the source of DTE timing when the
DTE timing mode is selected or as the source of
UBR1TE timing when the UBR1TE timing mode is
selected. If DTE timing is desired, the DTE interface
port sourcing the timing must be connected to Slot 1.
This slot will accept all other interface types except
Secondary Network interface option modules, including DSX-1 (PBX), the Full Drop and Insert (D&I) network interface, or the multiport Dial Backup (DBU).
Slot 2
Slot 2 is used for the multiport Dial Backup module if
it is installed. This slot accepts all other interface
types except Secondary Network interface option
modules, including DSX-1 (PBX) and the Full Drop
and Insert (D&I) network interface.
TSU 600 User Manual
61202076L1-1
Chapter 2. Installation
Slots 3-5
Slots 3-5 will accept any interface type except secondary interface, the interface for DTE timing, or the multiport DBU. If other interfaces have any restriction on
their location, this will be specified in the individual
option card manual (provided with the option cards).
Slot 6
Slot 6 services any option module type including secondary network interface ports (DSX-1 (PBX) and Full
D&I), but not the DTE timing source. If a secondary
network interface port is to be used, it must be
installed in slot 6.
You can use NxDBU modules in any slot.
Power-up Testing
When shipped from the factory, the TSU 600 is set to factory default conditions. At the first application of power, the unit automatically executes a memory self-test. A full self-test can be run from the front panel,
and a passcode and unit ID may be set using the UTIL menu.
Self-Test
Upon a power-up, the LCD displays Memory Test Now Testing and the
Test LEDs are illuminated.
When . . .
Then . . .
the self-test is complete
with no failures detected
the OK LED lights up and the LCD
momentarily displays All Tests
Passed.
a failure is detected
a list of failures is displayed in the
LCD window
61202076L1-1
TSU 600 User Manual
2-11
Chapter 2. Installation
The full self-test procedure (invoked from the front panel or
T-Watch PRO) consists of the following tests:
Board level tests
Each of the TSU 600 boards contains an on-board processor which executes a series of tests checking the circuitry on the board.
• RAM and EPROM tests
• Verify on-board circuitry
Unit level tests
• Front panel LED verification
• Board-to-board interface test
A test pattern is sent from the controller through a loopback on all other
boards and checked on the controller. This verifies the data path, clocks,
and control signals for the entire chassis.
Initialization
Set User Passcode
The TSU 600 is designed to operate with or without the use of a passcode. The default condition is without a passcode.
If the unit is to be remotely accessed using T-Watch PRO, you must enter
a passcode. When managing a number of units, the passcode can be the
same for all the units.
The passcode should be a number easily remembered. Once entered,
the passcode is required to access any operation other than viewing. See
Set Passcode on page 6-2.
Set Unit Identification
The Unit ID sets the unit to respond to remote control (controlled by a
device other than the front panel or terminal). If no Unit ID is recorded
it is not possible to operate from any remote control device, including
the local PC for T-Watch PRO or SNMP. See Unit ID on page 6-3 for details.
2-12
TSU 600 User Manual
61202076L1-1
Chapter 2. Installation
Set Control Port
The TSU 600 can be configured from the control port when T-Watch
PRO, SNMP, or the terminal interface is being used.
If the control port is to be used, the control port baud rate must also be
selected.
Chain-In (PC)
The unit can be controlled from an external PC connected directly or via
modem to the Chain-In port. When using Chain-In, the selection of the
Control Port baud rate from 9600 (factory default), 1200, 2400, or 4800,
19200, or 38400 must be made using the Unit Configuration menu. Unless locked out externally, the front panel can also control the unit.
Chain In/Chain Out
TSU 600 units and other TSUs can be linked together to form a chain.
Figure 2-4 provides an example of a chain-in arrangement with a PC or
a modem. The first TSU 600 in the chain receives controlling input from
the PC or modem.
PC or Modem
Control
Input
Chain
Out
TSU 600
Chain
In
Chain
Out
TSU 600/
TSU 100/TSU
Chain
In
Chain
Out
TSU 600/
TSU 100/TSU
Figure 2-4. Example of Chain In
Subsequent TSUs in the chain are in a position to intake information
from another TSU. This in-taking of information from another TSU in
the chain is identified as Chain-In. The baud rate for the chained units
must match that of the first unit.
Unless locked out externally, the front panel can also control the unit.
At this point, the Unit Initialization procedure is concluded. If the unit
is to be configured remotely, there are no additional items necessary to
complete prior to executing remote configuration.
61202076L1-1
TSU 600 User Manual
2-13
Chapter 2. Installation
The Passcode, the Unit ID, and the Control Port settings are stored in a
nonvolatile memory. This ensures that they are operable for subsequent
power-up sequences.
Normal Power-Up Procedure
After the unit has been put into operation with the initial power-up and
initialization, subsequent power-up procedure includes only the PowerUp Self-Test followed by the request for a passcode (password) if this
option was selected during initialization.
Use the number keys to key in the previously recorded passcode and
press Enter.
2-14
TSU 600 User Manual
61202076L1-1
Operation
Chapter 3
FRONT PANEL
The TSU 600 front panel both monitors operation and controls the configuration of the unit. The TSU 600 front panel is shown in Figure 3-1 on
page 3-4. Descriptions of each part of the front panel follow.
Name
Description
LCD Window
Displays menu items and messages in two lines by
16 characters. It also displays alarm and status
information.
Enter
Selects active menu items. To select a menu item,
press the number of the item. The menu item
flashes, indicating it is activated. Press Enter to
select the menu item.
Up and down
arrows
Up and down arrows are used to scroll through
and activate the submenu items available in the
current menu. When the submenu items are
scrolled, the flashing cursor indicates the active
parameters.
Cancel
Pressing the Cancel key stops the current activity
and returns the display to the previous menu.
Repeat until the desired menu level is reached.
When a submenu item is displayed, press Cancel
to exit the current display and return to the previous menu.
Numeric Keypad The numeric keypad contains the numbers 0
through 9 which are used to activate menu items
and enter information (such as the IP address).
61202076L1-1
TSU 600 User Manual
3-1
Chapter 3. Operation
Name
Description
To enter special function keys, press and release
Shift before pressing the key representing the
desired character. See Operation Keys on page 3-5
for a description of the function keys.
Shift
To activate a special function key rather than a
number, press Shift and then the key. If you press
the key without using Shift, the numbered item
becomes active instead of the special function key.
CSU Status LEDs
The CSU status LEDs display the operational condition of the network
interface located on the controller board in the unit.
Name
Description
OK (green)
Indicates the operation is in the normal mode and no
errors have been detected.
Test (yellow)
Indicates that the network interfaces are operating in a
test mode. This includes a self-test or a test loopback.
When lighted, this LED also indicates that normal data
flow is not occurring on the network interface.
Error (red)
Indicates an error such as a BPV, OOF, or CRC.
Alarm (red)
Indicates an alarm condition has been detected. When the
alarm condition is no longer valid, the OK LED activates
(turns on).
To view an alarm condition, select the active alarm menu
item or select Alarm by pressing Shift 8.
If the alarm conditions have been corrected, the alarm
which caused the activation of the Alarm LED can be
viewed under the Unit History menu.
3-2
TSU 600 User Manual
61202076L1-1
Chapter 3. Operation
Module Status LEDs
The module status LEDs display the operational condition of ports installed in the option slots.
Name
Description
OK (green)
Indicates the operation is in the normal mode
and no errors have been detected.
Test (yellow)
Indicates that one of the interfaces is operating in a test mode. This includes a self-test or
a test loopback. When lighted, this LED also
indicates that normal data flow is not occurring in at least one of the module ports.
Alarm (red)
Indicates an alarm condition has been
detected. When the alarm condition is no
longer valid, the OK LED activates (turns on).
To view an alarm condition, select the active
alarm menu item or select Alarm by pressing
shift 8. If the alarm conditions have been corrected, the alarm which caused the activation
of the Alarm LED can be viewed under the
Unit History menu.
System (green)
Indicates the status of the power supplies.
If the LED is illuminated green, all installed
power supplies are functioning properly.
If the LED is illuminated red, one or both
power supplies are not functioning normally.
This feature is for the AC-powered 600e only.
For the TSU 600 and DC- powered 600e, the
system LED is always green.
61202076L1-1
TSU 600 User Manual
3-3
Chapter 3. Operation
.
4
2
1
5
3
6
8
7
9 10 11
TSU 600
ENTER
1
2
3
4
5
ALARM
8
HOME
0
6
CLEAR
9
SHIFT
#
7
COPY
CANCEL
SYSTEM
12
CSU
*
OK
TEST
ERROR
13
TEST
ALARM
ALARM
15
14
OK
16
1
2
3
4
5
6
17
1. LCD Window
Displays menu items and messages in 2 lines by 16 characters.
2. Cancel
Stops current activity and returns to the previous menu.
3. Enter
Selects active menu item
4. Copy
Copies last data entered into the current DS0.
5. Home
Returns to the main menu.
6. Alarm
Quick access to the active alarm display menus.
7. Clear
Clears data/results fields
8. Shift
Provides access to special function keys
9. Alarm (Module Status)
Active when an alarm condition has been detected.
10. Test (Module Status)
Active when the module is in test mode.
11. OK (Module Status)
Operation is in normal mode with no detected errors.
12. System LED
Indicates status of power supplies (600e only)
13. Up and Down Arrows
Scroll through and activate the submenu items available in the
current menu. The flashing cursor indicates the active parameter.
14. OK (CSU Status)
Operation is in normal mode with no detected errors.
15. Test (CSU Status)
Active when the network interface is in test mode.
16. Error (CSU Status)
Indicates errors such as BPV, OOF, and CRC.
17. Alarm (CSU Status)
Active when an alarm condition has been detected on the network interface.
Figure 3-1. TSU 600 Front Panel Layout
3-4
TSU 600 User Manual
61202076L1-1
Chapter 3. Operation
Operation Keys
Name
Description
Copy
Used in the DS0 mapping menu operations to copy
the last data entered into the current DS0. This key
operates without pressing the Shift key.
Home
Returns home to the Main Menu from any menu
location.
Alarm
Used as quick access to the active alarm display
menus. This can be activated while any other menu
item is in use. When the Alarm Menu is exited, the
unit returns to the location of the same menu that
was active when Alarm was selected.
Clear
Used in various menus to clear data/result fields.
General Menu Operation
The TSU 600 uses a multilevel menu structure containing both menu
items and data fields. All menu operations and data are displayed in the
LCD window. The menu items are numbered and can be viewed by
scrolling with the up and down arrows.
Name
Description
Data Field
You can edit menu items followed by a colon (:)
Display Only You cannot edit menu fields followed by an
Field
equal symbol (=). This symbol identifies a field
used for value display only
Arrows
61202076L1-1
Menus that display small up or down arrows in
the lower right corner indicate there are more
menu items than are visible on a two-line LCD.
Access the additional items with the up or
down arrows. You can also access undisplayed
menu items by using the appropriate menu
number.
TSU 600 User Manual
3-5
Chapter 3. Operation
Selecting and Activating a Menu Item
Step
Action
1
Choose a menu item by placing the cursor on the desired
menu item by either:
1. pressing the number corresponding to the menu item or,
2. highlighting it with the up and down arrows.
2
To activate the Alarm List option from the Status Menu
do the following:
1. Activate the Status Menu using the arrow keys or by
pressing 1. The cursor will flash on the number next to
the activated selection.
2. Press Enter.
3. Use the arrow keys to view submenu items.
4. Choose an item on the submenu such as ACTIVE
ALARMS.
5. Select the submenu with the arrow keys or by pressing
3.
6. Press Enter.
7. View the Alarm List using the arrow keys.
The front panel menu tree is shown below.
1) NI PERF RPTS
2) NI ERRORS
1)STATUS
3) ACTIVE ALARMS
(ALARM LIST)
4)VIEW HISTORY
END OF LIST
5) PORT STATUS
6) REMOTE PORT
7) CLEAR PORT ALM
8) ENET STATUS
9) PS STATUS
Figure 3-2. Example of Basic Front Panel Menu Travel
3-6
TSU 600 User Manual
61202076L1-1
Chapter 3. Operation
Editing the Data Field
Use the following steps to edit data fields preceded by a colon (:).
Step
Action
Result
1
Position the cursor on the The cursor moves to the data field
submenu item number
(to the right of the submenu item
and press Enter.
name).
2
Using the arrows, scroll to The value settings display one-at-ascan the available value
time in the data field position.
settings.
3
When the desired value is When the value is set, the cursor
displayed, press Enter to moves back to the submenu item
set that value.
position, indicating the operation is
complete.
4
Select another submenu
field or press Cancel to
return to the submenu.
61202076L1-1
Pressing Cancel before pressing
Enter voids any data changes. The
original data value is restored and
the cursor returns to the submenu
field.
TSU 600 User Manual
3-7
Chapter 3. Operation
Display Only Data Fields
Data fields preceded by an equal (=) symbol cannot be edited. See Figure
3-3 and the instructions listed below.
Data Field
Display Field
Figure 3-3. Display and Data Fields
Step
Action
1
Press Enter to move the cursor to the data field.
2
Use arrows to select AUTO and press Enter.
• The unit automatically sets the Line Build Out.
• The display field shows the value actually set.
• The equal symbol after LBO in the second line indicates the information that follows is displayed
data and cannot be edited.
Exit Any Menu Field Operation Or Display
Press Cancel as many times as required to return to the desired menu
level or press Home to return to the main menu.
3-8
TSU 600 User Manual
61202076L1-1
Chapter 3. Operation
Data Port Identification
When configuring the unit, menu selections will include options from
data port submenus. Selecting of data ports is necessary because the
TSU 600 uses a Slot-Port method to identify which data port the menu
item is referencing. If a module containing a PBX DSX-1 option card
with an Nx56/64 plug-on interface is installed in option slot 6, it would
be designated as:
DSX-1 Passthru=6.1
Where slot=6 and port =1.
The DSX-1 is located in option slot 6 and is the first port in that slot.
Nx56/64=6.2
Where slot=6 and port=2.
The Nx is located in Slot 6 and is the second port in that slot.
SLOT 1
SLOT 4
SLOT 2
SLOT 5
SLOT 3
SLOT 6
POWER SUPPLY
Viewed from the rear of the TSU 600, the module slots are arranged as
shown in Figure 3-4.
Figure 3-4. Module Slots, TSU 600
61202076L1-1
TSU 600 User Manual
3-9
Chapter 3. Operation
Front Panel Menu Structure
The TSU 600 uses a multilevel menu structure containing both menu
items and data fields. All menu operations and data display in the LCD
window.
The opening menu is the access point to all other operations. Each Main
Menu item has several functions and submenus to identify and access
specific parameters.
The front panel LCD of the Main Menu contains the following options:
Option
Status
Description
Displays all relevant information for the network
and DTE interfaces. For detailed information on
status options, see Chapter 4, Status Menu.
Config
Displays and sets the TSU 600 operational config(Configuration) uration, including all network interface parameters, the allocation of the DS0s, and the port
parameters.
For detailed information on configuration options,
see Chapter 5, Configuration Menu.
3-10
Util (Utilities)
Displays and sets system parameters. For detailed
information on utility options, see Chapter 6, Utility Menu.
Test
The Test menu initiates different types of unit tests
and displays test results in the LCD window. For
detailed information on test options, see Chapter 7,
Test Menu.
TSU 600 User Manual
61202076L1-1
Chapter 3. Operation
Alternate Methods of Control
T-Watch PRO (ADTRAN PC Program)
T-Watch PRO is the ADTRAN PC control program. It provides complete
control over the configuration of the TSU 600 using a graphical interface
and displays the same status and performance data as the front panel
LCD. This data is displayed in the form of tables and graphs.
The T-Watch PRO program has the following capabilities:
• Interfaces with a modem which permits dialing into a remote TSU
600 location to configure the unit or read the status or performance of
the unit.
• Receives traps from any TSU product.
• Records and creates display performance data over a 30 day period.
• Accesses units via the local area network.
T-Watch PRO/LAN Connection
To set up the TSU 600 to work with T-Watch PRO over the LAN, follow
these steps:
Step
1
Action
Set the Unit ID using the Front Panel.
See Unit ID on page 6-3 for more information.
2
Set Control Port to SLIP or Normal for 10BaseT (600e
only) using the Front Panel.
3
Configure the IP address default gateway, and subnet mask using the Front Panel.
The default gateway and subnet masks are not used
for SLIP mode.
4
61202076L1-1
Follow the installation instructions for T-Watch PRO
to start the program and connect to the unit.
TSU 600 User Manual
3-11
Chapter 3. Operation
T-Watch PRO/EIA-232 Connection
To set up the TSU 600 to work with T-Watch PRO over a direct EIA-232
connection, the following steps are required:
Step
Action
1
Set the Unit ID and the Passcode using the Front Panel.
See Unit ID on page 6-3 and Change/Set a Passcode on page
6-3 for more details.
2
Set the Control Port rate to the same setting as the PC
Com port.
3
Connect the PC Com port to the Chain-In port on the
TSU 600 using the DB25 to modular adapter and 6-foot
modular cable.
4
Follow the installation instructions for T-Watch PRO to
start the program and connect to the unit.
SNMP
The ADTRAN TSU 600 supports the Simple Network Management Protocol (SNMP) through the chain-in (SLIP) interface or 10BaseT interface
(600e only). See Appendix B, Understanding SNMP for detailed information.
To use SNMP with the TSU 600, do the following:
Step
Action
1
Set Control Port to SLIP for Chain-In Port or Normal for 10BaseT
(600e only).
2
Set the IP address, default gateway, and subnet mask through the
front panel.
The default gateway and subnet mask are not used in SLIP mode.
3
3-12
Load the appropriate MIB browser into the Network Management
Station (available on the ADTRAN webpage at http://www.adtran.com). The MIB browser issues SNMP gets/sets to the TSU 600.
TSU 600 User Manual
61202076L1-1
Chapter 3. Operation
Terminal Mode Connection
The TSU 600 provides the front panel menus to a VT-100 type terminal.
This mode can be used to configure and monitor the unit. Initiate this
mode by typing <ctrl> PTT on the terminal once it is connected to the
Chain-In port. For detailed information on this method of control, see
Telnet Terminal Menus on page 8-1.
Telnet Connection
You can connect to the TSU 600 via telnet. Before attempting to connect
via telnet, first define the IP address, the default gateway, and subnet
mask using the front panel.
The dafault gateway and subnet mask are not used in SLIP mode.
When you begin the Telnet session, you will be prompted for a password. The default password is ADTRAN. You can change this password using the Management submenu. See Default Unit Passcode on
page 8-7, for details. The telnet session will time-out after a predefined
value that is also set in the Management Menu.
Only one telnet session can be active at one time.
61202076L1-1
TSU 600 User Manual
3-13
Chapter 3. Operation
3-14
TSU 600 User Manual
61202076L1-1
Status Menu
Chapter 4
The Status menu branch allows you to view the status of the TSU 600 operation. See Figure 4-1.
%AS
%EF
1) NI PERF RPTS
ES
2) NI ERRORS
UAS
SES
1)STATUS
3) ACTIVE ALARMS
(ALARM LIST)
END OF LIST
4)VIEW HISTORY
(HISTORY LIST)
END OF HISTORY
5) PORT STATUS
OPTION LIST
6) REMOTE PORT
7) CLEAR PORT ALM
8) ENET STATUS
9) PS STATUS
Figure 4-1. Complete Status Menu
61202076L1-1
TSU 600 User Manual
4-1
Chapter 4. Status Menu
Menu flow is normally depicted from left to right. Arrows on the lower
right of the screen indicate the direction of scrolling to use to view additional menu items. At every level of the menu, pressing Cancel returns
the system to the previous menu level. Press Cancel repeatedly to return
the system to the main menu.
Network Performance Reports (NI PERF RPTS)
The Network Interface Performance Reports display the user copy of the
performance data. See Figure 4-2. The TSU 600 maintains this performance data on the network in compliance with ANSI T1.403 and AT&T
document TR54016. The data displayed is data accumulated over the
last 15 minutes and over the last 24 hours.
Use the scroll keys to access the complete display of the following report
fields:
15 Minutes
24 Hours
Data Values
%AS
% of available seconds
%EF
% of error free seconds
ES
Number of errored seconds (1 or more
errors/second
SES
Number of severely errored seconds
(more than 320 errors/second)
UAS
Number of unavailable seconds (10 or
more consecutive seconds)
Figure 4-2. Network Interface Performance Report
4-2
TSU 600 User Manual
61202076L1-1
Chapter 4. Status Menu
If insufficient time has passed to collect data, NA displays. Continue
with standard operating procedures to exit the display.
When this menu is active, performance data can be cleared by pressing
Clear (Shift 9) on the keypad. Only the user copy of the performance
data is cleared.
Since only the user’s copy of performance data is cleared by the TSU 600,
the data displayed here might be different from the data sent to the network as PRM data.
Network Interface Errors (NI ERRORS)
The NI Errors submenu displays the types of errors the Network Interface (NI) detects. A blinking CSU error LED indicates that network errors are detected.
The asterisk (*) above an item indicates the type of errors detected. The
error types are as follows:
61202076L1-1
CRC
CRC-6 bit errors based on the FDL.
This is valid only in ESF mode.
BPV
Bipolar violations.
XS0
Excess zeros.
FER
Framing errors.
TSU 600 User Manual
4-3
Chapter 4. Status Menu
Active Alarms
This menu item displays a list of current alarms reported by either the
base controller or any of the ports. If no alarms are current, the menu
item displays End of List. See Figure 4-3.
This display includes two lines of text. The top line is the alarm source.
The bottom line is the alarm message. A list of alarm messages is found
in Appendix C, System Messages, on page C-1.
In addition to normal menu operation, you can also access this menu
item with the Alarm function (Shift 8) on the keypad. If one or more of
the Alarm LEDs are illuminated, an alarm is present. Press Cancel to return to the previous menu item.
Alarm Source
Alarm
Message
Figure 4-3. Display of Alarm Messages
View History
This menu item displays and clears the accumulated status changes of
the unit.
View History displays a history of the first 20 status changes in the unit,
including the date, time, and type of change. The unit also records for
viewing the date and time an alarm became active and inactive, as well
as the date and time of test activation and deactivation.
To clear the View History display, press Clear (Shift 9) with the View
History menu active.
4-4
TSU 600 User Manual
61202076L1-1
Chapter 4. Status Menu
Port Status
Port Status displays the signals monitored on the data ports. For example, an Nx56/64 interface monitors the RTS, CTS, TD, and RD, along
with other signal lines. When a port is selected, the LCD indicates
whether the signal is present.
Remote Port
Remote Port displays the status of activity on the Chain-In remote port.
This is useful for troubleshooting communication sessions, as well as
verifying cabling.
RX
Characters received at remote port.
ID
Unit ID received at remote port.
CRC Correct CRC received.
PC
Correct passcode received.
TX
Characters transmitted from the remote port.
Clear Port Alarm
Clears the Link Failed alarms on option modules that have been removed from the TSU 600 chassis.
61202076L1-1
TSU 600 User Manual
4-5
Chapter 4. Status Menu
ENET Status (600e only)
TX
Indicates that data is being transmitted from the 10BaseT port
RX
Indicates that data is being received by the 10BaseT port
LNK Indicates the current status of the 10BaseT link integrity test.
This should always be on when the unit is connected to a
functional 10BaseT hub.
CPU Active when the CPE is accessing the 10BaseT interface.
PS Status (600e only)
Displays the status of Power Supply A (PSA) and Power Supply B (PSB)
for AC powered units. Displays DC supply for DC Powered units.
Possible status: NOT PRESENT, INACTIVE, OK, DC Supply (DC units
only)
4-6
TSU 600 User Manual
61202076L1-1
Configuration Menu
Chapter 5
The Configuration menu sets the TSU 600 operational configuration, including all network interface parameters, the allocation of the DS0s, and
the port parameters. See Figure 5-1.
1) FORMAT
1) NETWORK (NI)
1) CTL PORT RATE
2) CODE
2) TRAPS
3) YEL ALARM
3) ACCESS
4) XMIT PRM
4) INIT MODEM
5) TIMING MODE
5) CONTROL PORT
6) SET LBO
6) IP ADDRESS
7) INBAND LPBCK
7) SUBNET MASK
8) BIT STUFFING
A) ALARM REPORT
8) DEFAULT ROUTER
9)TR-08 OPTIONS
B) ALARM FORMAT
9) SLIP RATE
C) BPV THRESHOLD
A) SLIP FLOW CTL
2) UNIT
B) PROXY TRAPS
3) MAP XCHNG
OFF
AUTO
1) MAP A @: HH:MM
4) MAP IN USE: A(B)
2) MAP B @: HH:MM
1) COPY A>TEMP
2) CONFIG 5)DS0 MAP A
2) CREATE TEMP
3) REVIEW MAP A
6) DS0 MAP B
1) COPY B > TEMP
4) REVIEW TEMP
2) CREATE TEMP
5) EDIT TEMP
3) REVIEW MAP B
6) APPLY TEMP > A
4) REVIEW TEMP
5) EDIT TEMP
6) APPLY TEMP > B
7) PORT CONFIG
(OPTION PORTS)
Figure 5-1. Configuration Menu
61202076L1-1
TSU 600 User Manual
5-1
Chapter 5. Configuration Menu
Menu flow is normally depicted from left to right. Arrows on the lower
right of the screen indicate the direction of scrolling to view additional
menu items. At every level of the menu, pressing Cancel returns the system to the previous menu level. Pressing Cancel repeatedly returns the
system to the Main menu.
NETWORK (NI)
This menu item accesses the configuration of parameters associated
with the network interface in the base unit. There are nine submenu
items that include setting the format, the Line Build Out (LBO), and the
timing mode. Submenu items do not include setting the parameters
which may be necessary for a secondary interface (DSX-1 Passthru, etc.).
Network (NI) Menu Items
The menu items and their descriptions follow.
Format
Sets the frame format for the NI.
Choices: D4, ESF, SLC96
D4 is equivalent to superframe format (SF).
5-2
Code
Sets the line code for the NI.
Choices: AMI, B8ZS.
YEL Alarm
Enables and disables the transmitting of yellow
alarms.
Choices: ENA, DISA
XMIT PRM
Enables and disables the sending of PRM data on
the facility data link (FDL).
The PRM data continues to be collected even if
XMIT PRM is disabled (possible only with ESF
Format).
Choices: Off, On.
Timing Mode
Selects the clock source for transmission toward
the network from the NI. See TSU 600 Clock
Sources on page 5-4 for more information.
Choices: Network, DTE (Slot 1), Normal (CSU),
U-BR1TE (Slot 1), Internal, and Secondary (SI).
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
SET LBO
Selects the line build out for the network interface.
In AUTO mode, the TSU 600 sets the LBO based
on the strength of the receive signal and displays
the selected value.
Choices: 0.0 dB, 7.5 dB, 15 dB, 22 dB, and Auto
To activate the -36 dB receiver sensitivity, set
the LBO to AUTO. This feature is useful in a
point-to-point application where no network
elements are involved. If a network element
such as a Smart Jack is installed on the circuit,
the LBO should be set to 0 dB.
INBAND
LPBCK
Sets unit to accept or reject the network interface
loop-up and loop-down codes as defined in ANSI
T1.403.
Choices: Accept, Reject
BIT STUFFING When enabled, bit stuffing causes the TSU 600 to
monitor for ones (1s) density violations and insert
a one (1) when needed to maintain ones at 12.5%.
Choices: Enable, Disable
TR-08
The TR-08 submenu configures the unit for TR-08
applications. The submenu items and their
descriptions follow.
Alarm Report
Enables and disables the transmitting of alarm
reports.
Choices: SEND ALARMS, DISABLE ALARMS
Alarm Format
Sets the alarm frame format to 13 frames or 16
frames.
Choices: ORB-13, ORB-16
BPV Threshold
Sets the threshold for BPVs to trigger an alarm.
Choices: 10-4, 10-5, 10-6
61202076L1-1
TSU 600 User Manual
5-3
Chapter 5. Configuration Menu
TSU 600 Clock Sources
The TSU 600 is operable from various clock sources, permitting it to perform properly in many different applications. The network interface
timing mode is set by using the Network (NI) Configuration menu options. The following options are available:
•
•
•
•
•
•
Network Timing
DTE Timing
UBR1TE
Internal Timing
Secondary Timing
Normal (CSU) Timing
The selected clock option always designates the clock source for transmission. Clocking necessary for receiving data is always recovered from
incoming data.
Network Timing
The network is the source of timing. The received data clocking is
looped back to the network, where it is used to determine the transmission timing. This option is also referred to as loop timed as the transmission clock is derived from the received clock. See Figure 5-2.
NETWORK
INTERFACE
1
2
3
4
5
6
SECONDARY
INTERFACE
TIMING SOURCE
OPTION SLOTS
Figure 5-2. Network Timed Clock Source
5-4
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
DTE Timing
The DTE is the source of timing. The TSU 600 uses the incoming DTE
clock to determine the transmission timing. This is typically used in applications where it is necessary to have the DTE as the primary clock
source (such as limited distance line drivers). See Figure 5-3.
The DTE source timing is restricted from use when a secondary interface
is used at the same time.
Clock
NETWORK
INTERFACE
1
2
3
4
5
6
OPTION SLOTS
DTE
TIMING SOURCE
Figure 5-3. DTE Timed Clock Source
U-BR1TE (Slot 1)
The timing mode selection U-BR1TE (Slot 1) works much like DTE timing except that the clock is derived from the U interface.
61202076L1-1
TSU 600 User Manual
5-5
Chapter 5. Configuration Menu
Internal Timing
The TSU 600 is the source of timing. The TSU 600 is configured to use its
own internal oscillator as the source of timing. Applications include private line driver circuits where one end is set to network and the other to
internal. See Figure 5-4.
NETWORK
INTERFACE
1
2
3
4
5
6
SECONDARY
INTERFACE
(Option)
OPTION SLOTS
OSC
TIMING SOURCE
Figure 5-4. Internal Clock Source
5-6
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
Secondary Timing
The secondary interface is the source of timing. The TSU 600 uses the
clock derived by the secondary interface for transmission timing. See
Figure 5-5.
NETWORK
INTERFACE
1
2
3
4
5
6
SECONDARY
INTERFACE
(Option)
OSC
OPTION SLOTS
TIMING SOURCE
PBX or
Second Network
Figure 5-5. Secondary Clock Source
61202076L1-1
TSU 600 User Manual
5-7
Chapter 5. Configuration Menu
Normal (CSU) Timing
The typical timing option arrangement is shown in Figure 5-6. The PBX
is looped timed to the TSU 600. The Network Interface (NI) is the actual
source of timing. This timing option is the same as that typically used for
CSUs. This is the preferred mode for use with a PBX application.
NETWORK
INTERFACE
1
2
3
4
5
6
SECONDARY
INTERFACE
(Option)
TIMING SOURCE
OSC
OPTION SLOTS
PBX or
Second Network
Figure 5-6. Normal (CSU)
5-8
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
Unit Menu
The Unit menu changes the baud rate of the Chain-In port and the setup
of the Chain-Out port. The menu items are:
Ctl Port
Rate
Sets the baud rate for communication with the
PC or modem.
Choices: 1200, 2400, 9600, 19200 and 38400 kbps
Traps
Enables or disables the transmission of trap messages.
Choices: Enable, Disable
Access
Sets the method of connection from the TSU 600
to T-Watch PRO/SNMP.
Choices:
Direct - Used if connected directly to the PC
Dial - Used when connection is through a
modem. The dial string is entered from T-Watch
PRO/SNMP.
Init Modem Allows you to choose an industry standard or a
custom initialization string for a modem connected to the control port.
Control Port Selects the TCP/IP physical interface.
Choices: SLIP using the EIA-232 serial port or
10BaseT Ethernet (600e only).
If this option is set to SLIP, the Chain-In port
may not be used as a terminal interface.
IP Address
61202076L1-1
Uniquely identifies the TSU 600 on a TCP/IP
network. This address is composed of four decimal numbers, each in the range of 0 to 255, separated by periods.
TSU 600 User Manual
5-9
Chapter 5. Configuration Menu
Subnet
Mask
Defines which part of a destination IP address is
the network number. Used along with the TSU
600e IP address to determine which nodes must
be reached through the default IP Gateway.
This value is set to 0.0.0.0 when the IP interface
option is set to SLIP.
Default
Router
All IP Packets destined for nodes not on the TSU
600e unit’s local network are not forwarded
through this IP address. Normally, this address
defines a router connected to the TSU 600e unit’s
local network. This value is ignored when the IP
interface is set to SLIP.
SLIP Rate
Sets the baud rate for the Chain-In port when
used as the SLIP connection for SNMP management.
Choices: 1200, 2400, 4800, 9600, 19200, 38400
SLIP Flow
CTL
Used to activate flow control on the Chain-In
port when used as the SLIP interface. Hardware
mode uses RTS and CTS.
Choices: None, Hardware
Proxy Traps Enables or disables the transmission of trap messages from units being "proxied" for.
Choices: Enable, Disable
5-10
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
Map Exchange (Map Xchng) Menu
The Map Exchange menu enables and sets the automatic time-of- day
map switch. The unit provides selection of the hour, minute, and seconds for the map switching to take place.
The menu items are:
OFF
Indicates the map in use does not change (disabled).
Off disables the Automatic Map Change feature.
Press Enter to activate the selection.
AUTO
Indicates that the map in use will change at a userselected time of day.
AUTO enables the Automatic Map Change feature.
Press Enter to activate the selection
When Auto is selected, the unit displays the screens
to set times for switching. After editing Map A,
press Enter to record the Map A settings and activate
the selection fields for Map B. Use the same operation to edit switching time for Map B.
When ESF is used with an FDL channel between
units, the units automatically coordinate the automatic map switch by sending a map switch command from end-to-end over the FDL. Only one end
needs to be set to Auto for this to work.
MAP In Use: A(B) Menu
This menu item controls the DS0 map the TSU 600 uses and displays the
map in current use.
61202076L1-1
TSU 600 User Manual
5-11
Chapter 5. Configuration Menu
DS0 Map A and DS0 Map B Menu
The DS0 maps designate which DS0s are assigned to which port. See
Figure 5-7. There are three maps: DS0 Map A, DS0 Map B, and the Temporary (Temp) map.
TEMP
DS0 A
DS0 B
Figure 5-7. DS0 Map Designations
DS0 A and DS0 B are the current maps the TSU 600 uses.
The Temp Map generates a map before putting it into use.
You can copy DS0 A to DS0 B by copying the DS0 A map into the Temp
map. Then apply (write) the Temp map into DS0 B.
The menu items are:
COPY A >TEMP
Copies the current map (A or B) into a
Temp map area.
Permits modification without disturbing
the existing map. When the modifications
are completed, the Temp map is written to
current MAP A (B) by selecting Apply.
CREATE TEMP
5-12
Creates a map by defining a port or Idle for
all DS0s.
When CREATE TEMP is first selected, all
DS0s are set to Idle. See Create Temp Example on page 5-13 for more information.
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
REVIEW MAP
A(B)
Permits a quick review of the number of
DS0s assigned to each port and the number
of unassigned DS0s (Idle or TST) as defined
in the currently applied Map A(B).
REVIEW TEMP
This menu item is operated the same for
the Temp map as is 3)REVIEW MAP A or
Map B.
EDIT TEMP
The map in the Temp file can be edited to
whatever configuration is desired. If Map
A had been copied into the Temp file, then
after editing, the Temp file could be
applied to MAP A or MAP B. The menu
operation is identical to 2) CREATE TEMP
with the exception that the existing port
selections display.
APPLY TEMP > A Writes the Temp map into Map A. Pressing
Apply is usually the last step in updating a
map and is accessed automatically at the
end of editing or creating a temporary
map. It can be bypassed at this time by
selecting another menu choice.
Create Temp Example
A sample selection follows for Create Temp:
DS0: 01 to 24
PORT: IDLE, TST, + option module ports
TST designates which DS0s are used for QRSS testing when activated
under the TEST Menu. When not used for testing, the TST designation
is identical to IDLE.
61202076L1-1
TSU 600 User Manual
5-13
Chapter 5. Configuration Menu
1. With the cursor on CREATE TEMP , press Enter. The unit displays the
selection screen with the cursor positioned on the first selection DS0
number. See Figure 5-8.
Select DSO Number
Select Port
Figure 5-8. Create Temp Selection Screen
2. Enter the DS0 number by using either the scroll method or numbers.
Do not mix the use of the keys.
3. Pressing Enter completes the selection and moves the cursor to PORT,
the next field.
4. Scroll to select the port which is dependent on the installed option
card.
5. Press Enter to complete the selection and move the cursor back to the
DS0 field.
With the cursor on the DS0 field, the DS0 number can be incremented or
decremented by scrolling. If you press Copy, the contents of the last DS0
entered are placed in the new DS0 number.
When all entries are complete, Cancel moves the cursor to the last of the
submenu choices, 6)APPLY. Either apply the newly created DS0 map or
press Cancel to return to the DS0 Map A (B) submenu choices.
Selecting Apply will not disrupt the operation of unmodified ports.
5-14
TSU 600 User Manual
61202076L1-1
Chapter 5. Configuration Menu
Port Configuration (Port Config)
Port Configuration selects and configures the parameters associated
with any data port in the unit. For example, parameters for the DSX-1
(PBX) interface are set through this menu. The items that can be set depend on which option module is installed. The list of option ports will
vary with the configuration.
The TSU 600 is designed so that any additional ports developed in the
future will contain the appropriate menu selections to provide access by
use of this menu item.
The Config menus for options ports are described in separate sections of
the manual supplied with the option card.
61202076L1-1
TSU 600 User Manual
5-15
Chapter 5. Configuration Menu
5-16
TSU 600 User Manual
61202076L1-1
Utility Menu
Chapter 6
The utility menu tree displays and sets system parameters. See Figure 61. This includes setting the time and date, resetting all parameters to factory values, or re-initiating the unit. This menu also displays the unit
software revision and the Unit ID setting.
TIME: HH:MM:SS
1) TIME/DATE
DATE: MM/DD/YY
2) FACTORY RESTORE
to factory settings)
3) SET PASSCODE
NEW PASSCODE
(Returns all configurations
3) UTIL
VERIFY PASSCODE
4) UNIT ID
5) SOFTWARE REV
(Displays Current
Software Revision
6) PORT UTILITY
(OPTION PORTS)
7) ENET ADDRESS (600e only)
8) CMD MODE
Figure 6-1. Utility Menu Tree
61202076L1-1
TSU 600 User Manual
6-1
Chapter 6. Utility Menu
Menu flow is normally depicted from left to right. Arrows on the lower
right of the screen indicate the scrolling direction to view additional
menu items. At every level of the menu, press Cancel to return the system to the previous menu level. Pressing Cancel repeatedly returns the
system to the Main menu.
Time/Date
This menu option displays or edits the current time and date. The TSU
600 maintains the time and date during power-off conditions.
If you want to...
Do this...
Record the entry and
move to the next editing
position
Press Enter after any numeric change
Move to a different field
to edit
Press Enter at the editing position without
making any changes, or
Use the Up and Down Arrow keys
End the editing process
Press Cancel
Factory Restore
This menu item restores the factory default settings for all unit parameters, including configured DS0 maps.
Set Passcode
Enter Passcode from Other Menus
The Passcode prompt may make an unexpected appearance from other menu operations. This happens only when the unit is operating in the
limited access mode, i.e., without an active passcode. The limited access
mode may become active even if a passcode was entered, as it does
when there is no activity for ten minutes. If the unit is to be remotely accessed using T-Watch PRO, a passcode must be entered. When managing a number of units, the passcode can be the same for all.
The unexpected appearance of the Passcode prompt occurs, for example, while operating in a limited access mode and attempting to change
the data rate, (2)CONFIG, 2)UNIT, 1)CTL PORT RATE. Use the number
keys to enter the correct passcode and press Enter. The unit displays
Access Granted.
6-2
TSU 600 User Manual
61202076L1-1
Chapter 6. Utility Menu
Pressing any key after entering a passcode causes the unit to return to
the previous active menu. In this case it returns to 2)CONFIG, 2)UNIT,
1)CTL PORT RATE to permit changing the data rate.
Change/Set a Passcode
The passcode can be changed or set at any time or eliminated altogether
through the Utility menu item 3)SET PASSCODE. This procedure requires the current passcode (if one is established) for operation.
The passcode can only be entered by using numbers. After entering the
desired passcode, press Enter.
Set a null passcode at the 3)SET PASSCODE menu by pressing Enter
without any numbers. This sets a null passcode and grants unlimited
access.
Automatic Time-out Feature
For added security protection, the unit is equipped with an automatic
time-out for operation with the password. After ten minutes of inactivity, the unit reverts to limited access operation. To make changes in the
configuration, the passcode can be reentered. See Set Passcode on page
6-2 for further information concerning passcode use, and both limited
and editing access.
If the passcode number is lost, contact ADTRAN Customer Service for
assistance.
No Passcode Desired
At the New Passcode prompt (in the Set Passcode menu), press Enter
without any numerical entry. The system nullifies the need to enter a
password for subsequent use and proceeds to the Unit ID prompt.
Unit ID
This menu is used to access the current Unit ID setting. Viewing is available in limited access mode. Editing or changing the Unit ID requires
the use of a password as in editing mode. Unit Identification numbers
must be between 2 and 999. If an out-of-range number is entered, the
unit assumes the upper limit number of 999.
61202076L1-1
TSU 600 User Manual
6-3
Chapter 6. Utility Menu
Setting the Unit Identification
In the Unit ID menu (item 4) under the UTIL menu, enter any value between 2 and 999. The number 1 is reserved for the PC.
Pressing Enter records the Unit ID number and establishes its availability for operation by remote control. The unit proceeds to the
Set Control Port prompt.
No Unit ID Desired
Without entering any numbers at the Unit ID prompt, press Enter.
Pressing Enter with no Unit ID recorded establishes the unit as unable
to be operated by remote control.
Software Revision (Software Rev)
This menu provides access to the display of the current software revision level loaded into the base unit controller. This information is required when requesting assistance from ADTRAN Customer Service or
when updates are needed.
Use Cancel to exit.
Port Utility
This menu provides access to the display of the current software information for each port installed in the unit. This information is required
when requesting assistance from ADTRAN customer service or when
updates are needed.
ENET Address (600e only)
Displays the Ethernet MAC address for the 10BaseT port.
CMD Mode
Reserved for factory use.
6-4
TSU 600 User Manual
61202076L1-1
Test Menu
Chapter 7
The Test menu initiates different types of unit tests and displays test results in the LCD window. The Test menu contains four items. See Figure
7-1.
Executing tests will disrupt some of the normal operation. See individual menu items concerning tests before executing.
LINE ON
1) LOCAL LOOPBCK
PAYLOAD ON
NO LOOPBACK
1) NETWORK TESTS
ATT INBAND LLB
ANSI FDL PLB
2) REMOTE LOOPBK
ANSI FDL LLB
ANSI FT1 LLB
NO LOOPBACK
ALL ZEROS
4) TEST
3) TEST PATTERN
QRSS ALL DS0S
QRSS TST DS0S
ALL ONES
NONE
4) PATTERN RESULT
2) RUN SELFTEST
(Displays results)
3) PORT TEST
(OPTION PORT)
(Displays results)
4) CANCEL TESTS
Figure 7-1. Test Menu
61202076L1-1
TSU 600 User Manual
7-1
Chapter 7. Test Menu
Menu flow is normally depicted from left to right. Arrows on the lower
right of the screen indicate the scrolling direction to view additional
menu items. At every level of the menu, pressing Cancel returns the system to the previous menu level. Pressing Cancel repeatedly returns the
system to the Main menu.
Network Tests
Network tests control the activation of loopbacks and the initiation of
data test patterns.
Network tests are run on the Network Interface (NI). You can select
three different test configurations to determine the type of loopback and
the pattern to run. Test results display in the LCD window.
Executing Network Tests will disrupt normal data flow unless only
TST DS0s are selected for testing.
Loopback Tests
A number of different loopbacks can be invoked locally from the front
panel, by T-Watch PRO commands, or remotely by using special inband codes (AT&T D4 network loop up and loop down codes). Additionally, the loopbacks can be remotely controlled by means of out-ofband commands by the T1 ESF FDL or from T-Watch PRO by a modem
connection. See Figure 7-2.
7-2
TSU 600 User Manual
61202076L1-1
Chapter 7. Test Menu
Network Interface Loopbacks
Network interface loopbacks affect the entire T1 data stream. There are
two types of network loopbacks: line loopback and payload loopback.
Line loopback loops all of the received data back toward the network.
The transmitted data is the identical line code that was received, including any bipolar violations or framing errors.
Payload loopback is similar to line loopback, except that the framing is
extracted from the received data and then regenerated for the transmitted data.
TSU 600
NI CSU
Secondary
Interface
DS1
Payload Loopback
Line Loopback
Figure 7-2. Network Loopback Tests
Local Loopbck
There are three available choices for setting the local loopback:
Name
Description
Line On
Activates the line loopback
Payload On
Activates the payload loopback
No Loopback
Deactivates the loopback
Scroll to select a setting and record it by pressing Enter. The unit returns
to the previous menu level.
61202076L1-1
TSU 600 User Manual
7-3
Chapter 7. Test Menu
Remote Loopbk
This activates the same loopbacks as Local Loopback but at the far end.
It uses either the inband loopup code as specified by ANSI T1.403 for
line loopback (ATT In-Band LLB), or the FDL as specified in ANSI
T1.403 for payload and line loopback codes. The following options are
available:
Name
Description
ATT In-Band
LLB
Activates the line loopback using inband code
ANSI FDL PLB
Initiates the transmission of an FDL payload
loopup code toward the far end
ANSI FDL LLB
Initiates the transmission of an FDL line
loopup code toward the far end
ANSI FT1 LLB
Initiates the transmission of a FT1 loopback
using the inband code described in T1.403.
No Loopback
Deactivates the loopback
Remote Loopback can only be used with Fractional T1 if the ANSI FT1 LLB is
selected.
After a Remote Loopback option is selected, the TSU 600 verifies that the
far end is actually in a loopback by checking for the receipt of a code
looped back from the far end. Once the Remote Loopback type is selected, the LCD displays the loopback progress by displaying Looping until
loopback is verified.
7-4
TSU 600 User Manual
61202076L1-1
Chapter 7. Test Menu
Test Pattern
Pattern
Description
All Ones
Sends an all ones pattern to the network
All Zeros
Sends an all zeros pattern to the network
QRSS All DS0s
Generates a QRSS test pattern and inserts
the pattern into all DS0s
QRSS TST DS0s
Inserts a QRSS pattern in those DS0s
mapped as TST in the currently active map
(A or B)
None
Terminates pattern generation
QRSS Pattern
The QRSS pattern is commonly used to simulate real data in T1 interfaces. This pattern can be assigned to appear in all DS0s or only in TST
DS0s. When QRSS is set in all DS0s and one of the network loopbacks
previously described is activated at the far end, a total end-to-end integrity check can be run without the need for any external test equipment.
When QRSS is assigned to TST DS0s, an integrity check of the link can
be run along with normal data flow. The TST DS0s are user assigned as
part of the DS0 Map.
This sets the pattern for the test and initiates the transmission of the pattern. The test is terminated by selecting None. The following patterns
are available:
QRSS always runs at 64K/DS0.
Example:
1. Use the up and down key to select QRSS ALL DS0s.
2. Press Enter to record the selection. The TSU 600 starts to generate a
QRSS test pattern and inserts the pattern into all DS0s.
3. Select None to end the test.
61202076L1-1
TSU 600 User Manual
7-5
Chapter 7. Test Menu
Pattern Result
Displays the results of the test currently active. Leaving and returning to
this menu item does not interrupt the test.
Pressing 2 injects errors into the test pattern. These errors are detected
by the device performing the pattern check.
Pattern
Description
ES
The number of seconds with at least 1 bit error
BES
The number of seconds with more than 1 bit
error and less than 320
SES
The number of seconds with more than 320 bit
errors
SYNC
Indicates if pattern sync is (yes) or is not (no)
valid. An asterisk (*) indicates if pattern sync
has been lost since the start of testing
Clear results by pressing Shift 9. The results are accumulated until the
test pattern is set to None or Cleared.
Using TST DS0s for testing can be very useful, particularly in Fractional
T1 applications. You can run an end-to-end test on the Fractional DS0s
by:
1
Setting for Map B the TST in the same DS0 as used by Map A to
receive data from an Nx56/64 port, and
2
Looping the far end using a V.54 loopback code on the Nx56/64
port. In addition, a single DS0 can be used for continuous testing
while other DS0s are passing normal data.
This will also provide an end-to-end check on the entire link. Set each
end to send QRSS in TST DS0s (using 1 DS0) and occasionally view the
results on the Pattern Result Menu selection.
7-6
TSU 600 User Manual
61202076L1-1
Chapter 7. Test Menu
Run Self-Test
The self-test checks the integrity of the internal operation of the electronic components by performing memory tests and by sending and verifying data test patterns through all internal interfaces. Although actual
user data cannot be passed during these tests, the self-test can be run
with the network and DTE interfaces in place and will not disturb any
external interface.
The memory portion of the self-test automatically executes upon powerup. A full self-test can be commanded from a front panel menu or from
T-Watch PRO.
In addition to the specified self-tests, background tests are run on various parts of the internal electronics. These run during normal operation
to confirm continued correct functioning.
This menu selection is used to execute a full internal self-test. The results
of the self-tests are displayed in the LCD. Upon invoking the command,
the LCD displays System Self-Test and the Test LEDs are illuminated.
Test failures are displayed in the LCD window. The self-test consists of
the following tests:
Board level tests
Each of the TSU 600 boards contain an on- board processor which executes a series of tests checking the circuitry on the board.
• RAM tests; EPROM checksum
• DS0 map tests
• On-board data path; sending a known test pattern through an onboard loop
Unit level tests
• Front panel LED verification
• Phase Lock Loop verify
• Board-to-board interface test
A test pattern is sent from the controller through a loopback on all other
boards and is checked on the controller. This verifies the data path,
clocks, and control signals.
If a failure is detected, note the failure number and contact ADTRAN
Technical Support.
The execution of self-test will disrupt normal data flow and prevent remote communication until the self-test is completed.
61202076L1-1
TSU 600 User Manual
7-7
Chapter 7. Test Menu
Port Tests
The Port Tests menu is used to activate testing of specific data ports. It
controls the activation of loopbacks and the initiation of data test patterns. Test results are displayed in the LCD window.
The execution of Port Tests will disrupt normal data flow in the port being tested.
Cancel Tests
Use this menu selection to deactivate all active tests, including tests on
option modules.
7-8
TSU 600 User Manual
61202076L1-1
Telnet/Terminal Menus
Chapter 8
MAIN MENU
The Telnet/Terminal Main Menu is the first menu displayed after the
telnet/terminal session is established. See Figure 8-1. The default telnet/
terminal password is ADTRAN.
Only one telnet/terminal session may be active at a time.
ADTRAN - TSU 600
Password: XXXXXXXX
Main Menu
1)
2)
3)
4)
5)
6)
7)
8)
Status
Config
Util
Test
Remote Menu Access
Management Config
Flash Download
Quit Session
Figure 8-1. Telnet/Terminal Main Menu
61202076L1-1
TSU 600 User Manual
8-1
Chapter 8. Telnet/Terminal Menus
Status, Config, Util, and Test Menu Options
These menu items can access the same modified menus that you can access through the front panel. For detailed information on the available
menu options, refer to the following sections:
•
•
•
•
Status Menu in Chapter 4.
Configuration Menu in Chapter 5.
Utility Menu in Chapter 6.
Test Menu in Chapter 7.
DS0 Maps Configuration Menu
The Telnet/Terminal version of the DS0 maps configuration menu takes
advantage of the 24-line VT 100 display. Upon entering this menu, the
current Temp Map displays followed by nine selections that you can use
for configuring and reviewing map information.
TEMP MAP
DS0 #
1
2
3
4
5
6
7
8
9
10
11
12
1)
2)
3)
4)
5)
6)
7)
8)
9)
PORT
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
DS0 #
13
14
15
16
17
18
19
20
21
22
23
24
PORT
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
COPY MAP A TO TEMP MAP
COPY MAP B TO TEMP MAP
CREATE TEMP MAP
REVIEW MAP A
REVIEW MAP B
REVIEW TEMP MAP
EDIT TEMP MAP
APPLY TEMP MAP TO MAP A
APPLY TEMP MAP TO MAP B
Figure 8-2. DS0 Temp Map
• Use the up and down arrows or number keys to move the cursor
from one selection to another.
• Use the Enter key to perform the action displayed in the LCD to the
right of the cursor.
8-2
TSU 600 User Manual
61202076L1-1
Chapter 8. Telnet/Terminal Menus
Normally, map configuration involves these steps.
Step
Action
1
Initializes the Temp Map to one of three configurations (current Map A, current Map B, or all
IDLEs). This step is optional.
2
Edits the Temp Map so that it reflects the
desired map configuration.
3
Replaces the current DS0 map A or B configuration with the Temp Map configuration.
Initializing the Temp Map
Upon entering the DS0 maps configuration menu, the Temp Map reflects its last configured state. You can then use the following selections.
Use selections... To initialize...
1, 2, 3
1, 2
3
61202076L1-1
the displayed Temp Map to one of three
configurations.
the Temp Map from its current configuration to one which reflects the currently
stored Map A or B configurations, respectively.
the Temp Map to an all IDLE state.
TSU 600 User Manual
8-3
Chapter 8. Telnet/Terminal Menus
Editing the Temp Map
If further changes to the Temp Map are needed, do the following:
Step
1
Action
Explanation
Use selection 7 to enter
the Temp Map edit
mode.
Upon entering this mode, the cursor
location moves to DS0 number one in the
DS0 field of the Temp Map.
The cursor may be moved from one DS0
to another by using the up and down
arrows until the cursor is located at the
DS0 number whose assigned port needs
to be changed.
2
The up and down arrows are then used
Press the Enter key to
cause the cursor to move to scroll through the possible port selections.
into the Port field.
3
Press the ESC key
This restores the previous port assignment and returns to the DS0 field.
4
Press the Enter key
This saves the current selected port and
returns to the DS0 field.
Once the cursor is again located in the
Temp Map DS0 field, press the ESC key
a second time to return to selection 1
below the Temp Map display.
Applying the Temp Map
Once the Temp Map reflects the desired configuration, use selections 8
or 9 to apply this configuration to Map A or B, respectively.
Reviewing Maps
Selections 4 through 6 give a summary of the number of ports assigned
to Map A, Map B, and the Temp Map, respectively.
8-4
TSU 600 User Manual
61202076L1-1
Chapter 8. Telnet/Terminal Menus
Remote Menu Access
Displays telnet menus for a remote device (may be another TSU/TDU
or any other ADTRAN product that supports telnet via its EIA-232 chain
port). After selecting this option, you may choose to connect to a device
entered in the Unit Access Table or enter a Unit ID for a unit not in the
Unit Access Table. CTRL + X terminates the session and returns to the
TSU 600 Main Menu.
Management Configuration
This menu sets management information, such as SNMP community
names and trap destination addresses.
Unit Access Table
This menu edits and creates the Unit Access Table. This table stores the
Unit ID, Passcode, and Unit Type for units connected via chain ports or
connected remotely to the TSU/TDU (see Figure 8-3 on page 8-6). An
entry in the table is only required to support proxy SNMP MIB access or
polling. For MIB access, an entry is required only if the unit's passcode
is not the same as the Default Unit Passcode, or the unit is a single port
TSU Stand-alone.
It is not necessary to have an entry in this table for a remote unit in order to
telnet to it or forward SNMP traps from it. In the telnet case, the Remote Menu
Access menu is selected from the Main menu and a Unit ID is entered which
may or may not be in the Unit Access Table.
Units accessed via T-Watch PRO over TCP/IP use the Unit ID and passcode set by T-Watch PRO running on the PC.
61202076L1-1
TSU 600 User Manual
8-5
Chapter 8. Telnet/Terminal Menus
__________________Unit Access Table_________________
Unit ID
Passcode
Type
Polled
20
DEFAULT
Standard
No
3
0033
Standard
Yes
6
0095
TSU Stand Alone
No
8
0022
Standard
Yes
PollStatus
UP
UP
1) Add New Unit
2) Modify Unit
3) Delete Unit
4) Default Unit Passcode
0022
5) OK
Figure 8-3. Unit Access Table
Add New Unit
This adds a new device to the table. You must enter a device Unit ID,
passcode, unit type, and polled flag. The unit type can be Standard
(which supports any TSU/TDU Multiplexer and the ISU 512) or TSU
Standalone (a single port TSU with no option card slot). You can select a
passcode of 0 to 9999 for each device or DEFAULT, in which the default passcode will be used. See Figure 8-3.
Traps are normally sent from the unit in alarm to the TSU 600. For units
in the Unit Access Table that are not chained directly to the TSU 600 but
are managed over Inband or the FDL, traps are not automatically forwarded. Polling must be enabled on the TSU 600 for these units in order
to receive Traps on the NMS. The TSU 600 can be configured to poll selected units for traps by enabling the polled option when adding or
modifying a unit entry.
Modify Unit
Allows Unit ID, passcode, device type, and polled flag to be changed for
an existing entry in the table.
Delete Unit
Deletes an entry in the table.
8-6
TSU 600 User Manual
61202076L1-1
Chapter 8. Telnet/Terminal Menus
Default Unit Passcode
Sets the default passcode for all devices in the table that have passcodes
set to DEFAULT, or for any unit not listed in the table.
OK
Returns to the Configure Agent menu.
SNMP Read Community
SNMP Read Community Name defaults to public. NMSs using this
community name have Read access for all supported MIB objects but do
not have the ability to change MIB objects. This value must be set to the
same value on both the TSU 600 and the NMS (OpenView®, etc.) in order for the NMS to have Read access to MIBs supported by the TSU 600.
This value must be a text string of 16 characters or less.
SNMP Read/Write Community
SNMP NMS using this community name have full read/write access to
all supported MIB objects (defaults to private). This setting must be the
same value on both the TSU 600 and the NMS in order for the NMS to
have read/write access to MIBS supported by the TSU 600. This value
must be a text string that is 16 characters or less.
To access other units external to the TSU 600 (proxied units) using an SNMP
MIB browser, append a period and the Unit ID of the external device to the Read
Only and Read/Write community name used in the MIB Browser, for example,
public.4. See Appendix A, Understanding SNMP on page A-1, for more
information.
61202076L1-1
TSU 600 User Manual
8-7
Chapter 8. Telnet/Terminal Menus
SNMP Trap Community
This community name is used for all SNMP traps forwarded by the TSU
600. Traps received from daisy chained units have a period and the Unit
ID appended to the trap community name.
SNMP Trap Destination Address
Host 1 Trap IP Address
Description
This is the first of four entries for
SNMP trap destination addresses.
The TSU 600 forwards all SNMP traps
to the IP address specified in this
entry. If the address is set to the
default value of 0.0.0.0, no traps are
forwarded for this particular value.
Host 2 Trap IP Address
Defaults to 0.0.0.0. Second destination
address for SNMP traps.
Host 3 Trap IP Address
Defaults to 0.0.0.0. Third destination
address for SNMP traps.
Host 4 Trap IP Address
Defaults to 0.0.0.0. Fourth destination
address for SNMP traps.
System Name
A text string that can uniquely identify an SNMP-managed node.
System Contact
A text string containing the name, phone number, etc. of the individual
responsible for maintaining an SNMP-managed node.
System Location
A text string describing the physical location of an SNMP-managed
node (for example, SECOND FLOOR PBX ROOM).
8-8
TSU 600 User Manual
61202076L1-1
Chapter 8. Telnet/Terminal Menus
Auto. Fail Traps Sent
(DISABLED, ENABLED: defaults to DISABLED)
When enabled, the TSU 600 issues an SNMP trap when any SNMP request is received with an invalid community name. Can be used for security purposes.
Poll Link Status Traps Sent
(DISABLED, ENABLED, defaults to DISABLED)
When enabled, the TSU 600 sends an SNMP trap whenever a device configured to be polled fails to respond. When the device begins responding to polls, a poll link-up trap is sent. The formats of the traps are
defined in the agent MIB.
Ping IP Host
Allows the user to Ping a specific IP address.
Telnet/Terminal Time-out
The TSU 600 terminates a telnet or terminal session if no activity is detected for this length of time. Only one telnet or terminal session may be
active at one time. This time-out prevents an unattended session from
blocking interactive access to the agent. The default value is five minutes.
Telnet/Terminal Password
This option allows modification of the password required for entry into
a telnet or terminal session. The default value is ADTRAN.
Exit
Returns to the TSU 600 Main menu.
Flash Download
The TSU 600 uses flash memory that allows software updates via the
chain-in port. This menu selection allows you to perform a flash download manually using XMODEM. T-Flash is also available to automate
this process.
Quit Session
Terminates the telnet/terminal session.
61202076L1-1
TSU 600 User Manual
8-9
Chapter 8. Telnet/Terminal Menus
8-10
TSU 600 User Manual
61202076L1-1
Appendix A
Understanding SNMP
As local area network (LAN) environments became standardized over
the past ten years, multi-vendor equipment grew with competition. It
became necessary to manage the various vendor equipment from a single control console. Thus, the SNMP emerged as the standard for managing commercial TCP/IP networks.
The term SNMP broadly refers to the message protocols used to exchange information between the network and the managed devices, as
well as to the structure of network management databases.
Basic Components
SNMP has three basic components: Network Manager, Agent, and
MIB.
Network Manager
This is a control program that collects, controls, and presents data pertinent to the operation of the network devices. It resides on a network
management station.
Agent
This is a control program that responds to queries and commands from
the network manager and returns requested information or invokes
configuration changes initiated by the manager. It resides in each network device.
61202076L1-1
TSU 600 User Manual
A-1
Appendix A. Understanding SNMP
MIB
This is an index to the organized data within a network device. It defines
the operating parameters that can be controlled or monitored. When requesting the network manager to retrieve or modify a particular piece of
information about a network device, the network manager transmits the
request to that network device. The agent in that device interprets the incoming request, performs the requested task, and sends its response to
the network manager. The network manager collects all the data from
the various network devices and presents it in a consistent form.
Commands
Using SNMP Version 1, the network manager can issue three types of
commands: GetRequest, GetNextRequest, and SetRequest.
Command
Description
GetRequest
This command retrieves a single item or
the first in a series from a network device.
GetNextRequest
This command retrieves the next item in
a series from a network device.
SetRequest
This command writes information to a
network device.
Message
The network device issues two types of messages:
GetResponse and Trap.
Command
A-2
Description
GetResponse
This message is the response to a network manager GetRequest or GetNextRequest command.
Trap
This is an unsolicited message issued by a network device to report an operational anomaly or
an alarm condition to the network manager. These
messages are typically encased within informational packets and transported over the LAN or
WAN (wide area network).
TSU 600 User Manual
61202076L1-1
Appendix A. Understanding SNMP
TSU 600 SNMP ACCESS
By default, SNMP MIB Browser access to the TSU 600 IP address with
the configured community names, accesses the host. The TSU 600 can
also act as an SNMP proxy agent for external units. To access MIB variables on externally chained devices, append a period and the Unit ID of
the device to the Read and Read/Write community names.
Example:
If the Read community name configured in the TSU 600 is public, specifying "public.3" as the community name in the SNMP MIB Browser allows reading SNMP MIB variables from externally chained unit 3.
If the external unit's passcode is not the default, an entry must be added
to the Unit Access Table for SNMP MIB access. See Figure 8-3 on page 86 for a description of this operation. However, SNMP traps for the unit
can be forwarded without the entry.
SNMP Trap Configuration
Traps received by the TSU 600 from external units and the host unit are
converted into SNMP traps and forwarded to the configured NMS. The
source of the trap is uniquely identified at the NMS by a combination of
the IP address of the TSU 600, and the Unit ID of the sending device. The
Unit ID is present in the trap packet appended to the end of the trap
community packet name, for example public.4. It is also included as an
Octet String variable (adProdPhysAddress) in the trap packet as defined
in the individual product MIBs. The latest versions of the product MIBs
by default display the appended trap community name in their descriptions.
Typical steps required for Management Station trap configuration are
loading the device specific MIBs and loading or creating device specific
Trap Definition Files. The current product MIBs contain keywords embedded in comments that can be used by some network management
platforms to automatically generate Trap Definitions. Otherwise, the descriptions may be used as a template for Trap Definitions.
If individual option card port identification and slot identification are
required, they are present in the four byte adProdPhysAddress field of
the trap packet. The first two bytes are the Unit ID of the base controller
(least significant byte first). The next two bytes are port and slot number.
This field is the second object identifier in all traps sent from TSU/TDU
products.
61202076L1-1
TSU 600 User Manual
A-3
Appendix A. Understanding SNMP
For traps from the ISU 512, the Unit ID is the first object identifier. See
the product MIBs for more information.
Definitions for Poll Link Up/Down traps are included in the TSU 600
MIB file: 600e.MIB.
The TSU 600 and TSU 600e share the same MIB.
SNMP MIB Browser Configuration
The steps required to configure Network Manager MIB variable access
through the TSU 600 are as follows:
1. Load the desired product MIBs on the network management station.
If, for example, the administrator is managing TSU 600 and ISU 512
devices, load TSU 600e.MIB, ISU512.MIB, and RFC1406.MIB.
2. Create device entries in the NMS database for all units that are to be
managed through the TSU 600. The host unit should be configured as
the Proxy agent for the external units. The IP address or host name
used for the proxy designation is that of the TSU 600.
3. Set community names in the device’s entries for external units to the
TSU 600 community name with the device Unit ID appended as defined in the previous section, TSU 600 SNMP ACCESS on page A-3.
4. Set the device timeout for all device entries in the NMS device database to five seconds, including the host unit.
SNMP MIB Files
The TSU 600 supports several standard MIBs including MIB-II (RFC1213), the DS1 T1/E1 MIB (RFC-1406), and the Ethernet MIB (RFC1643; 600e only). It also supports several ADTRAN enterprise specific
MIBs including the ADTRAN Product MIB (ADTRAN.MIB), the ADTRAN DS1 extensions MIB (ADS1.MIB), and all TSU/TDU Enterprise
MIBs, such as 600e.MIB. The standard MIB files are usually included
with most SNMP network management software.
The latest versions of the ADTRAN enterprise-specific MIBs are available in the following locations:
A-4
•
ADTRAN anonymous ftp site (ftp.adtran.com),
•
By dial-up from the BBS (256-963-8169).
•
ADTRAN web site at http://www.adtran.com.
TSU 600 User Manual
61202076L1-1
Appendix B
Understanding TR-08
The TSU 600 chassis functions as a Remote Terminal in Digital Loop
Carrier and as Integrated Digital Loop Carrier Systems as described in
TR-TSY 000008. The TSU 600 supports SLC96 framing, Mode I operation, ORB-13 and ORB-16 alarm formats, alarm reporting, and user-definable BPV threshold detection rate.
A basic familiarity with DLC systems, IDLC systems, and TR-TSY000008 is assumed, but the following information will be useful:
•
All received TR-TSY-000008 specific alarms are reported locally
within the history feature of the TSU 600.
•
When the DISABLE ALARMS option is selected, no alarms will be
sent on the DLF, but received alarms will be reported locally in the
history.
•
Other alarms normally reported by the TSU 600 will also be placed
in history.
•
Each TSU 600 needs to be configured as the A SHELF, as it is provisioned as a separate entity.
•
All alarms will refer to A SHELF when received from TSU 600.
61202076L1-1
TSU 600 User Manual
B-1
Appendix B. Understanding TR-08
The following table explains what conditions trigger alarms and how
alarms are processed when received by the TSU 600.
Table B-1. Alarm Conditions
Name
Explanation
FELP
When the TSU 600 receives a FELP alarm, it will loop
the incoming data directly to the outgoing data. LINE
ON is placed in history. The alarms and loopback are
cleared when FELP is no longer received.
Loss of Data
The TSU 600 will send MINOR ALARM and the A
SHELF ALARM for 2.5s when it quits receiving the
data link on the T-Span. It will also report TR-08 DL
Down in the history. After 2.5s, MAJOR ALARM, A
SHELF ALARM are sent across the Data Link.
OOF
The TSU will send MINOR ALARM and A SHELF
ALARM upon receiving an out-of-frame condition.
TR-08 DL Down and RED ALARM are declared in
history for severe framing errors. After 2.5s, MAJOR
ALARM, A SHELF ALARM are sent across the Data
Link.
Loss of Signal The TSU 600 will send MINOR ALARM and the A
SHELF ALARM for 2.5s when it quits receiving a
signal from the far end. It will also report TR-08 DL
Down and LOS in the history. After 2.5s, MAJOR
ALARM, A SHELF ALARM are sent across the Data
Link, and RED ALARM is declared in history.
B-2
BPVs
BPVs that are received at a rate greater than the
threshold set under TR-08 options, will cause
MINOR ALARM and A SHELF ALARM to be sent
on the DL. If the BPVs remain above the threshold for
2.5s, the TSU 600 will send MAJOR ALARM and on
the DL. No events are placed in history.
Protection
Line Switch
The TSU will not respond to this alarm.
TSU 600 User Manual
61202076L1-1
Appendix B. Understanding TR-08
TR-08 DS0 Conversion Table
The following table contains the mapping conversions needed to map
voice ports to the TR-08 network.
Table B-2. TR-08 DS0 Conversion Table
61202076L1-1
DS0
TR-08 Channel Number
Port
1
1
1.1
3
2
1.2
5
3
1.3
7
4
1.4
9
5
2.1
11
6
2.2
13
7
2.3
15
8
2.4
17
9
3.1
19
10
3.2
21
11
3.3
23
12
3.4
2
13
4.1
4
14
4.2
6
15
4.3
8
16
4.4
10
17
5.1
12
18
5.2
14
19
5.3
16
20
5.4
18
21
6.1
20
22
6.2
22
23
6.3
24
24
6.4
TSU 600 User Manual
B-3
Appendix B. Understanding TR-08
B-4
TSU 600 User Manual
61202076L1-1
Network Pinouts
Appendix C
WIRING
Network
On the rear panel of the TSU 600 is an 8-position modular jack labeled
NETWORK. This connector is used for connecting to the network. See
Table C-1, Network Pinouts for the pinout for the network connector.
Network Connections
The network connections are as follows:
Connector Type
(USOC) RJ-48C
Part Number
AMP# 555164-2
Table C-1. Network Pinouts
Pin
Name
Description
1
R1 RXDATA-RING
Receive data from the network
2
T1 RXDATA-TIP
Receive data from the network
3
UNUSED
4
R1 TXDATA-RING
Send data toward the network
5
T TXDATA-TIP
Send data toward the network
6,7,8
61202076L1-1
UNUSED
TSU 600 User Manual
C-1
Appendix C. Network Pinouts
Control In/Chain In
This is used as an EIA-232 port for connection to a computer or modem
(Control-in) or to another TSU 600 or TSU 100 (chain-in). See Table C-2,
Control In/Chain In Pinout for the pinout for the control-in/chain-in connector.
Chain-in Connections
The chain-in connections are as follows:
Connector Type
RJ-48
Part Number
AMP# 555164-2
Table C-2. Control In/Chain In Pinout
Pin
Description
1
GND
Ground-connected to unit chassis
2
RTS
Request to send-flow control
3
RXDATA
Data received by the TSU 600
4
UNUSED
5
TXDATA
6,7
UNUSED
8
C-2
Name
CTS
Data transmitted by the TSU 600
Clear to send -- flow control
TSU 600 User Manual
61202076L1-1
Appendix C. Network Pinouts
Chain-Out
This is used to connect to another TSU 600 chain-in connector. See Table
C-3, Chain-Out Pinout for the pinout for the chain-out connector.
Chain-out Connections
The chain-out connections are:
Connector Type
RJ-48
Part Number
AMP# 555164-2
Table C-3. Chain-Out Pinout
Pin
Name
1
GND
2
UNUSED
3
TX DATA
4
UNUSED
5
RX DATA
Description
Ground-connected to unit chassis. Connected to
GND of next unit (pin 10).
Data transmitted to chained units by the TSU
600. Connect to RX DATA of the next unit (chainin pin 3).
Data received from chained units by the TSU
600. Connect to TX DATA of the next unit (chainin pin 5).
6,7,8 UNUSED
61202076L1-1
TSU 600 User Manual
C-3
Appendix C. Network Pinouts
10BaseT (600e only)
10BaseT is used to connect the TSU 600e to the Local Area Network. See
Table C-4.
10BaseT Connections
The required wiring connections are:
Connector Type
(USOC) RJ-45
Part Number
AMP# 555164-1
Table C-4. 10BaseT Ethernet
C-4
Pin
To NIC
1
TX1
2
TX2
3
RX1
6
RX2
TSU 600 User Manual
61202076L1-1
Appendix D
System Messages
This appendix lists and defines the alarm and status messages that appear on the TSU 600 screen.
Alarm Messages: Network Interface (NI)
Message
Red Alarm
Description
NI unable to frame align with incoming signal
Yellow Alarm Remote alarm indication (RAI) being received from
far end
Blue Alarm
Unframed all ones (1s) (AIS) being received at NI
Loss of Signal No signal detected at NI
61202076L1-1
TSU 600 User Manual
D-1
Appendix D. System Messages
Status Messages: Network Interface (NI)
Message
Description
Payload On
Payload loopback activated
Line On
Loopback off
Loopback Off
All loopbacks deactivated
Factory Restore
Factory setting restored
Power On
Unit powered on
Self-Test
Internal self-test performed
TR-08 DL Down* TR-08 data link is down
TR-08 DL Up*
TR-08 data link is up
Minor Alarm*
Loss of sync, carrier loss, BPV threshold
exceeded, or data link failure.
Major Alarm*
Conditions for a minor alarm have continued for greater than 2.5 seconds.
*TR-08 alarm messages appearing in the alarm or history log have
been received from the far end. If the NI detects one of the above
conditions, it will send the appropriate alarm (if enabled) to the far end
but no message will appear in the alarm or history log.
D-2
TSU 600 User Manual
61202076L1-1
Specifications
Appendix E
ELECTRICAL SPECIFICATIONS
T1/FT1 Interface
61202076L1-1
T1 Line Rate
1.544 Mbits/s ± 75bps
Line Code
Bipolar, RZ; AMI or B8ZS
Framing
D4(SF), ESF, or SLC96
FT1 Line Rate
DS0 Channelized (multiple of 64 kbps)
Transmit Timing
Network, DTE, U-BR1TE Secondary NI, Normal (CSU) or Internal
Input Signal
0 to -36 dB (DS-1)
Line Build-out
0, 7.5, 15, 22.5 dB, AUTO
Connector
RJ-45
Test Jacks
Bantam jacks: TX and RX (to Network) and
MON
TSU 600 User Manual
E-1
Appendix E. Specifications
Compatibility
T1 Interface
Pub 62411
ESF Format Interface
TR. 194
ESF Performance Monitoring TR. 54016 and T1.403
FCC Part 15
FCC Part 68
UL 1950
Approvals:
Management Interfaces
Chain-In/Chain-Out Ports
Interface Devices PC Serial Port, Modem or SLIP
connection to router
Interface Type
EIA-232
Data Rates
1200, 2400, 4800, 9600, 19200,
38400
Data Format
EIA-232 N81
Protocols
TWATCH/ADLP, ATEL/ADLP,
SLIP, TCP/IP
Connector
RJ-45
Option Slot Interface
Slots 1-6
Interface
ADTRAN proprietary, accepts standard TSU
Option Modules.
Chassis Specification
E-2
Height
Less than 5.25-inch (will fit in a 3U rack mount opening)
Width
Will fit within a 19-inch rack
TSU 600 User Manual
61202076L1-1
Appendix E. Specifications
Environmental Specifications
Input Power
TSU 600:
90 - 130 VAC 60 HZ
TSU 600e:
90 - 120 VAC 50/60 HZ
DC powered units:
21 - 26 VDC or 40 - 56 VDC
Fuse
AC powered units:
1A, 250V
DC powered units:
5A, 250V
Operating
Temperature
0 to 45 degrees C
Max Power
40 W
Consumption
Max Current
61202076L1-1
AC powered units: 0.7A
DC powered units: 3A
TSU 600 User Manual
E-3
Appendix E. Specifications
E-4
TSU 600 User Manual
61202076L1-1
Index
Numerics
ANSI FDL PLB, remote loopback 7-
10BaseT Connections C-4
10BaseT Interface 2-10
10BaseT, interface with SNMP 3-12
ANSI FT1 LLB, remote loopback
4
A
Access, unit menu 5-9
Active Alarms 4-4
Add New Unit to unit access table,
how to 8-6
ADTRAN
PC
Management
Program, T-Watch PRO 3-11
ADTRAN PC Program, T-Watch
PRO 3-11
ADTRAN Web page 3-12
Agent, SNMP component A-1
AIS Alarm, (Blue Alarm) network
interface alarm message D-1
Alarm (red), LED description 3-2
Alarm (red), module status LED 3-
3
Alarm Conditions, TR-08 B-2
Alarm Format, TR-08 5-3
Alarm Messages
Network Interface (NI) D-1
Alarm
Messages,
Network
Interface D-1
Alarm Report, TR-08 5-3
Alarm, operation key 3-5
ANSI FDL LLB, remote loopback 7-
4
61202076L1-1
7-
4
APPLY TEMP > A, DS0 map menu
item 5-13
Applying the Temp Map, how to 8-
4
AS, available sec., NI errors 4-2
ATT In-Band LLB, remote loopback
7-4
Auto. Fail Traps Sent, SNMP 8-9
B
Backup Power Supply for TSU 600e
2-2
BES, pattern result, test menu 7-6
BIT STUFFING, network menu
item 5-3
Blue Alarm, (AIS alarm), network
interface alarm message D-1
Board level tests 2-12
Board level tests, run self-test 7-7
BPV Threshold, TR-08 5-3
BPV, TSU 600 T1 error 4-3, 5-3
BPVs, alarm condition TR-08 B-2
C
Cancel Tests, test menu 7-8
Cancel, front panel 3-1
Chain In/Chain Out 2-13
TSU 600 User Manual
Index-1
Index
Chain Port Output 2-9
Chain-In (PC) 2-13
Chain-in Connections C-2
Chain-out Connections C-3
Chain-Out Pinout C-3
Chassis Specification E-2
Clear alarm history 4-4
Clear Port Alarm 4-5
Clear,operation key 3-5
CMD Mode, utility menu 6-4
Config, front panel menu 3-10
configuration applications, TSU 600
1-5
Configuration Menu Tree 5-1
Control Port Input 2-9
Control Port, unit menu 5-9
COPY A >TEMP, DS0 map menu item
5-12
Copy, operation key 3-5
CRC, TSU 600 T1 error 4-3
CREATE TEMP, DS0 map menu item
5-12
Create Temp, example, how to
Ctl Port Rate, unit menu 5-9
5-13
D
Data Port Identification 3-9
data port identification 3-9
DC Powered TSU 600, about 2-2
Default Router,unit menu 5-10
Delete Unit in unit access table, how
to 8-6
Dial Backup, option module for TSU
600 1-3
Display Only Data Fields 3-8
Drop and Insert, Voice and Router
Application 1-6
DS0 Map A and DS0 Map B Menu 5-
1-3
DSX1 , option module for TSU 600
1-
3
DTE Timing
5-5
E
EDIT TEMP, DS0 map menu item
5-
13
Editing the Data Field, how to 3-7
Editing the Temp Map, how to 8-4
EF, error free sec., NI errors 4-2
Electrical specifications, TSU 600 E-1
ENET Address, utility menu 6-4
ENET Status 4-6
Enter, front panel 3-1
Environmental Specifications E-3
Error (red), LED description 3-2
ES, Errored Sec., NI Errors 7-6
ES, errored sec., NI errors 4-2
Exit Any Menu Field Operation Or
Display, how to 3-8
F
Factory Restore, network interface
status message D-2
features, TSU 600 1-2
FELP, alarm condition TR-08 B-2
FER, TSU 600 T1 error 4-3
Flash Download 8-9
Flash Download, telnet/terminal
menu 8-9
Front Panel Menu Structure 3-10
front panel menu tree 3-6
Front Panel, description 3-1
Full Drop and Insert, option module
for TSU 600 1-3
12
G
DS0 Maps Configuration Menu 8-2
DSO Map A and DSO Map B 5-12
DSU DP, option module for TSU 600
GetNextRequest, SNMP command
Index-2
A-2
GetRequest, SNMP command
TSU 600 User Manual
A-2
61202076L1-1
Index
GetResponse, SNMP message
Grounding Instructions 2-4
A-2
H
3-11
Home, operation key 3-5
http
//www.adtran.com, ADTRAN
Web page 3-12
I
INBAND LPBCK, network menu
item 5-3
Init Modem, unit menu 5-9
Initialization 2-12
Initializing the Temp Map, how to 8-
3
Installing and Replacing the Power
Supply, how to 2-3
Internal Timing 5-6
IP Address, unit menu 5-9
L
LCD Menu Options 3-10
LCD Window, front panel 3-1
Line On, network interface status
message D-2
Line On, setting local loopback 7-3
Local Loopbck, test menu 7-3
Loopback Off, network interface
status message D-2
Loopback Tests, test menu 7-2
Loss of Data, alarm condition TR-08
B-2
Loss of Signal, alarm condition TR-08
B-2
Loss of Signal, network interface
alarm message D-1
M
Major Alarm, network interface status
61202076L1-1
message D-2
Management Configuration 8-5
Management software - T-Watch PRO
Map Exchange Menu 5-11
MAP In Use
A(B) Menu 5-11
MIB, SNMP component A-2
Minor Alarm, network interface
status message D-2
Modify Unit to unit access table, how
to 8-6
Module Status LEDs 3-5
N
Network 7-2
Network
(NI)
Menu
Item,
configuration menu 5-2
Network (NI), configuration menu 5-
2
network connections, pinouts C-1
Network Interface Errors 4-3
Network Interface Loopbacks, test
menu 7-3
network interface, (NI) port 2-9
Network Manager, SNMP component
A-1
Network Performance Reports 4-2
Network Test Interface 2-9
Network Tests, test menu 7-2
Network, pinouts C-1
NI errors, AS (available sec.) 4-2
NI errors, EF (error free sec.) 4-2
NI errors, ES (errored sec.) 4-2
NI Errors, ES, Errored Sec 7-6
NI errors, SES, Severly Errored
Seconds 7-6
NI errors, SES, severly errored
seconds 4-2
NI errors, UAS (unavailable errored
sec.) 4-2
No Loopback, remote loopback 7-4
TSU 600 User Manual
Index-3
Index
No Loopback, setting local loopback
7-3
No Unit ID Desired, utility menu,
what to do 6-4
Normal (CSU) Timing 5-8
Normal Power-Up Procedure 2-14
Numeric Keypad, front panel 3-1
Nx56 1-3
Nx56/64 module, router interface 1-6
Nx56/64 Serial Interface, option
module for TSU 600 1-3
NxIQ, option module for TSU 600 1-3
O
message D-2
power-up procedure 2-14
Power-up Testing 2-11
Product Description, TSU 600 1-1
Product Overview, TSU 600 1-1
Protection Line Switch, alarm
condition TR-08 B-2
Proxy Traps, unit menu 5-10
PS Status, power supply 4-6
Q
QRSS Pattern, test menu 7-5
Quit Session, telnet/terminal session
8-9
OCU DP, option module for TSU 600
R
1-3
OFF, map exchange menu 5-11
OK (green), LED description 3-2
OK (green), module status LED 3-3
OOF, alarm condition TR-08 B-2
operation keys 3-5
Option Module Architecture 1-4
Option Module Architecture, for TSU
600 1-4
Option Slot Arrangement, for TSU 600
2-10
5-13
P
Pattern Result, test menu 7-6
Payload On, network interface status
message D-2
Payload On, setting local loopback 7-
3
Ping IP Host, SNMP 8-9
Poll Link Status Traps Sent, SNMP
8-
9
port configuration 5-15
Port Status 4-5
Port Tests, test menu 7-8
Port Utility, utility menu 6-4
Power Connection for TSU 600 2-2
Power On, network interface status
Index-4
Rear Panel Layout, of TSU 600 2-5
Receipt Inspection, for TSU unit 2-1
Red Alarm, network interface alarm
message D-1
Remote Loopbk 7-4
Remote Menu Access 8-5
Remote Port 4-5
REVIEW MAP A(B), DS0 map menu
item 5-13
REVIEW TEMP, DS0 map menu item
Reviewing Maps, how to 8-4
router interface with Nx56/64
module 1-6
Router, PBX, Video Conferencing
Application 1-5
Run Self-Test, test menu 7-7
S
Secondary Timing 5-7
Selecting and Activating a Menu Item,
how to 3-6
Self-Test, network interface status
message D-2
SES, Severly Errored Seconds, NI
TSU 600 User Manual
61202076L1-1
Index
errors 7-6
SES, severly errored seconds, NI
errors 4-2
Set Control Port 2-13
SET LBO, network menu itme 5-3
Set Passcode, how to 6-2
Set Unit Identification 2-12
Set User Passcode 2-12
SetRequest, SNMP command A-2
Setting the Unit Identification for
utility menu, how to 6-4
Shift, front panel 3-2
shipping damages, what to do 2-1
Simple
Network
Management
Protocol (SNMP) 3-12
SLIP Flow CTL, unit menu 5-10
SLIP Rate, unit menu 5-10
SNMP Commands A-2
SNMP Messages A-2
SNMP MIB Browser Configuration
A-4
SNMP MIB Files A-4
SNMP Trap Community 8-8
SNMP Trap Configuration A-3
SNMP, Basic Components A-1
SNMP, how to use with TSU 600 3-12
Software Revision (Software Rev),
utility menu 6-4
Status menu, description 4-1
Status Messages, Network Interface
D-2
Status, Config, Util, and Test Menu
Options 8-2
Status, front panel menu 3-10
Subnet Mask, unit menu 5-10
SYNC, pattern result, test menu 7-6
System (green), module status LED 3-
3
system contact, SNMP text string 8-8
system location, SNMP text string 8-8
system name, SNMP text string 8-8
T
Telnet Connection 3-13
Telnet/Terminal Main Menu 8-1
Telnet/Terminal Password, SNMP 8-
9
Telnet/Terminal Time-out, SNMP
8-
9
Terminal Mode Connection 3-13
Test (yellow), LED description 3-2
Test (yellow), module status LED 3-3
Test menu 7-1
Test Pattern, test menu 7-5
Test, front panel menu 3-10
TR-08 alarm conditions B-2
TR-08 DL Down, network interface
status message D-2
TR-08 DL Up, network interface
status message D-2
TR-08 DS0 Conversion Table B-3
TR-08,network menu item 5-3
Trap, SNMP message A-2
Traps, unit menu 5-9
TSU 600 Clock Sources 5-4
TSU 600 Configuration Applications
1-5
TSU 600 Electrical specifications E-1
TSU 600 Front Panel Layout, with
descriptions 3-4
TSU 600 General Menu Operation 3-5
TSU 600 Interfaces 2-6, 2-9
TSU 600 interfaces 2-6
TSU 600 Option Modules, option
modules, for TSU 600 1-3
TSU 600 SNMP access A-3
TSU 600, Overview 1-1
TSU 600, power connection 2-2
TSU 600, Standard Features 1-2
TSU Product Description 1-1
T-Watch PRO 3-11
T-Watch PRO, modem connection 3-
11
T-Watch PRO/EIA-232 Connection
61202076L1-1
TSU 600 User Manual
Index-5
Index
3-12
T-Watch PRO/LAN Connection 3-11
V
Voice Interface, option module for
TSU 600 1-3
U
UAS, unavailable errored sec., NI
errors 4-2
U-BR1TE (Slot 1) 5-5
U-BR1TE , option module for TSU 600
W
1-3
X
Unit Access Table 8-5
unit level tests 2-12
Unit level tests, run self-test 7-7
Unit Menu 5-9
Up and down arrows, front panel 3-1
Util, front panel menu 3-10
utility menu tree 6-1
Index-6
Wiring, network pinouts
XS0, TSU 600, T1 alarm
C-1
4-3
Y
Yellow Alarm, network
alarm message D-1
TSU 600 User Manual
interface
61202076L1-1
Product Support Information
Presales Inquiries and Applications Support
Please contact your local distributor, ADTRAN Applications Engineering,
or ADTRAN Sales:
Applications Engineering
(800) 615-1176
Sales
(800) 827-0807
Post-Sale Support
Please contact your local distributor first. If your local distributor cannot
help, please contact ADTRAN Technical Support and have the unit serial
number available.
Technical Support
(888) 4ADTRAN
Repair and Return
If ADTRAN Technical Support determines that a repair is needed, Technical
Support will coordinate with theCustomer and Product Service (CaPS) department to issue an RMA number. For information regarding equipment
currently in house or possible fees associated with repair, contact CaPS directly at the following number:
CaPS Department
(256) 963-8722
Identify the RMA number clearly on the package (below address), and return to the following address:
ADTRAN, Inc.
CaPS Department
6767 Old Madison Pike
Progress Center
Building #6, Suite 690
Huntsville, AL 35807
RMA # _____________
Download PDF

advertising