Specifications | ADTRAN 1240 Network Router User Manual

®
Total Access 1240
Installation and Maintenance Practice
Document Number: 61179605L5-5B
September 2005
Total Access 1240 Installation and Maintenance Practice
Trademarks
Front Matter
Any brand names and product names included in this manual are trademarks, registered
trademarks, or trade names of their respective holders.
To the Holder of the Manual
The contents of this publication are current as of the date of publication. ADTRAN® reserves
the right to change the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or
for commercial losses even if ADTRAN has been advised thereof as a result of issue of this
publication.
®
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
(256) 963-8000
©2005 ADTRAN, Inc.
All Rights Reserved.
ii
61179605L5-5B
Revision History
Revision
Date
Description
A
December 2004
Initial release
B
September 2005
This revision includes updates to the User Interface and Application Guidelines sections, general updates to the power and
ground connection information, and updates to the Ethernet
and VLAN interface information.
Conventions
The following typographical conventions are used in this document:
This font indicates a cross-reference link. First-time references to tables and figures are
shown in this font.
This font indicates screen menus, fields, and parameters.
THIS FONT indicates keyboard keys (ENTER, ESC, ALT). Keys that are to be pressed simultaneously
are shown with a plus sign (ALT+X indicates that the ALT key and X key should be pressed at the
same time).
This font indicates references to other documentation and is also used for emphasis.
This font indicates on-screen messages and prompts.
This font indicates text to be typed exactly as shown.
This font indicates silk-screen labels or other system label items.
This font is used for strong emphasis.
NOTE
Notes inform the user of additional, but essential, information or
features.
CAUTION
Cautions inform the user of potential damage, malfunction, or disruption to equipment, software, or environment.
WARNING
Warnings inform the user of potential bodily pain, injury, or death.
61179605L5-5B
iii
Total Access 1240 Installation and Maintenance Practice
Training
ADTRAN offers training courses on our products. These courses include overviews on product
features and functions while covering applications of ADTRAN’s product lines. ADTRAN
provides a variety of training options, including customized training and courses taught at our
facilities or at customer sites.
For inquiries concerning training, contact ADTRAN:
Training Phone:
800-615-1176, ext. 7500
Training Fax:
256-963-6700
Training Email:
training@adtran.com
iv
61179605L5-5B
Contents
Section 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-2
1-2
1-2
1-3
1-4
Section 2
Application Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
VLAN Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Traffic Prioritization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
System Configuration Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Section 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Mounting the Total Access 1240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Flush-mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Mid-mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Ground and Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Fans/Fan Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Alarm Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
SHDSL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
61179605L5-5B
v
Total Access 1240 Installation and Maintenance Practice
Section 4
Provisioning Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Section 5
User Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
System Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Craft Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a Personal Computer Emulating a VT100 Terminal to Total Access 1240 . . . . . . . . .
Inband Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5-1
5-2
5-2
Logging on to the Total Access 1240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Menu Trees. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Menu Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Bridge Circuit Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Bridge Port Summary Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Bridge User Port Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Strict Prioritization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
VLAN Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
EtherType Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Local Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Router Dest Mac Filtering Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Apply Provisioning to Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Ethernet Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Duplex Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
Speed Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Current Ethernet Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Previous Ethernet Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
Current Bridge Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Previous Bridge Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
System Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
Password Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36
Password Control Levels Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Set or Change Username or Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38
Mode Selection and Current IP Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-39
Static IP Settings - for IP over Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
Restore IP Factory Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
Dynamic IP Settings - for IP over Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-43
Restore IP Factory Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44
Test IP Address Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45
Time/Date Adjust Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-46
Current Baud Rate Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
System Configuration Archive Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49
SNMP Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-51
vi
61179605L5-5B
Contents
SNMP Contact Information Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Community Names Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Trap Hosts Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Alarm Severity Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Code Download Method Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Y-Modem Download Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TFTP Firmware Download Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Factory Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Factory Defaults Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Service State Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Interface Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Rate Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 G.991.2 Annex Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 LineProbing Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 PMMS Margin Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Alarm Thresholds Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Local Loopback Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Dual-Sided Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Customer Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Network Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Remote Loopback Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Dual-Sided Loopback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Customer Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Network Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHDSL Loop 1 Performance Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Alarm Log Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-52
5-53
5-55
5-57
5-58
5-59
5-60
5-61
5-63
5-64
5-65
5-66
5-68
5-69
5-70
5-71
5-72
5-73
5-74
5-75
5-76
5-77
5-78
5-80
5-82
5-83
5-84
5-85
5-85
5-85
5-86
5-87
5-87
5-87
5-88
5-89
5-90
Section 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Section 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Appendix A
Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
61179605L5-5B
vii
Total Access 1240 Installation and Maintenance Practice
Appendix B
SCA File Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
SCA Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
File Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
SCA File Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
Appendix C
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Warranty and Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADTRAN Sales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADTRAN Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADTRAN Repair/CAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair and Return Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii
C-1
C-1
C-1
C-1
C-1
61179605L5-5B
Contents
Figures
Figure 1-1.
Figure 1-2.
Figure 1-3.
Figure 2-1.
Figure 2-2.
Figure 2-3.
Figure 3-1.
Figure 3-2.
Figure 3-3.
Figure 3-4.
Figure 3-5.
Figure 3-6.
Figure 3-7.
Figure 3-8.
Figure 3-9.
Figure 5-1.
Figure 5-2.
Figure 5-3.
Figure 5-4.
Figure 5-5.
Figure 5-6.
Figure 5-7.
Figure 5-8.
Figure 5-9.
Figure 5-10.
Figure 5-11.
Figure 5-12.
Figure 5-13.
Figure 5-14.
Figure 5-15.
Figure 5-16.
Figure 5-17.
Figure 5-18.
Figure 5-19.
Figure 5-20.
Figure 5-21.
Figure 5-22.
Figure 5-23.
Figure 5-24.
Figure 5-25.
Figure 5-26.
Figure 5-27.
Figure 5-28.
Figure 5-29.
Figure 5-30.
Figure 5-31.
Figure 5-32.
Total Access 1240 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Total Access 1240 Compliance Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Total Access 1240 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Total Access 1240 Ingress and Egress Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
System Configuration Archive Concept Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Flush-mount Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Mid-mount Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Four-point Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Alarm Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
SHDSL 50-pin Male Amphenol Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Craft Port Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Total Access 1240 Main Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Total Access 1240 System Management Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Total Access 1240 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Bridge Circuit Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Bridge Port Summary Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Bridge User Port Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Strict Prioritization Concept Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
EtherType Filtering Concept Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Local Switching Concept Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Destination Mac Filtering Concept Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Router Dest Mac Filtering Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Apply Provisioning to Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Ethernet Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Duplex Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
Speed Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Current Ethernet Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Previous Ethernet Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
Current Bridge Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Previous Bridge Statistics Previous Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
System Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
Password Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36
Password Control Levels Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Mode Selection and Current IP Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-39
Static IP Settings - for IP Over Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
Restore IP Factory Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
Dynamic IP Settings - for IP over Ethernet Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-43
Restore IP Factory Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44
Test IP Address Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45
Time/Date Adjust Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-46
61179605L5-5B
ix
Total Access 1240 Installation and Maintenance Practice
Figure 5-33.
Figure 5-34.
Figure 5-35.
Figure 5-36.
Figure 5-37.
Figure 5-38.
Figure 5-39.
Figure 5-40.
Figure 5-41.
Figure 5-42.
Figure 5-43.
Figure 5-44.
Figure 5-45.
Figure 5-46.
Figure 5-47.
Figure 5-48.
Figure 5-49.
Figure 5-50.
Figure 5-51.
Figure 5-52.
Figure 5-53.
Figure 5-54.
Figure 5-55.
Figure 5-56.
Figure 5-57.
Figure 5-58.
Figure 5-59.
Figure 5-60.
Figure 5-61.
Figure 5-62.
Figure 5-63.
Figure 5-64.
Figure 5-65.
Figure 5-66.
Figure 5-67.
Figure 5-68.
Figure 5-69.
Figure 5-70.
Figure 5-71.
Figure 5-72.
Figure 5-73.
Figure B-1.
x
Current Baud Rate Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
System Configuration Archive Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49
SNMP Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-51
SNMP Contact Information Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-52
SNMP Community Names Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53
SNMP Trap Hosts Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-55
External Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-57
External Alarm Severity Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58
Code Download Method Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-59
Y-Modem Download Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-60
TFTP Firmware Download Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-61
Restore Factory Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-63
Reset System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64
SHDSL Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65
SHDSL Loop 1 Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66
Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68
Card Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69
Restore factory Defaults Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-70
SHDSL Loop 1 Provisioning Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71
SHDSL Loop 1 Service State Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72
SHDSL Loop 1 Interface Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-73
SHDSL Loop 1 Rate Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
SHDSL Loop 1 G.991.2. Annex Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
SHDSL Loop 1 LineProbing Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-76
SHDSL Loop 1 PMMS Margin Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-77
SHDSL Loop 1 PMMS Margin Screen Worst Case Option . . . . . . . . . . . . . . . . . . . . . . 5-77
SHDSL Loop 1 Alarm Thresholds Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-78
SHDSL Loop 1 Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-80
Alarm Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-82
SHDSL Loop 1 Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83
SHDSL Loop 1 Local Loopback Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-84
Local Dual-Sided Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-85
Local Customer Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-85
Local Network Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-85
SHDSL Loop 1 Remote Loopback Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86
Remote Dual-Sided Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87
Remote Customer Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87
Remote Network Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87
SHDSL Loop 1 Performance Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88
System Alarm Log Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-89
Contact Information Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-90
SCA File Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-7
61179605L5-5B
Contents
Tables
Table 1-1.
Table 3-1.
Table 3-2.
Table 3-3.
Table 4-1.
Table 4-2.
Table 4-3.
Table 4-4.
Table 4-5.
Table 5-1.
Table 5-2.
Table 5-3.
Table 5-4.
Table 5-5.
Table 5-6.
Table 5-7.
Table 5-8.
Table 5-9.
Table 5-10.
Table 5-11.
Table 5-12.
Table 5-13.
Table 5-14.
Table 5-15.
Table 5-16.
Table 5-17.
Table 5-18.
Table 5-19.
Table 5-20.
Table 5-21.
Table 5-22.
Table 5-23.
Table 5-24.
Table 5-25.
Table 5-26.
Table 5-27.
Table 5-28.
Table 5-29.
Table 5-30.
Table 5-31.
Table 5-32.
Table 5-33.
Table 5-34.
Table 5-35.
Table 5-36.
Table 5-37.
Table 5-38.
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Total Access 1240 Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Alarm Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
SHDSL Cable Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Bridge User Port Default Provisioning Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Ethernet Default Provisioning Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
SNMP Management Default Provisioning Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
User Port Default Provisioning Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
SNMP Configuration Default Provisioning Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
General Keyboard Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Menu Specific Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Total Access 1240 Main Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Configuration Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Bridge Circuit Management Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Bridge Port Summary Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Bridge User Port Provisioning Menu Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Bridge User Port Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Traffic Type Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Router Dest Mac Filtering Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Apply Provisioning to Ports Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Apply Provisioning to Ports Menu Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
Ethernet Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Duplex Mode Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
Speed Mode - 100Base Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Current Ethernet Statistics Menu Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Current Ethernet Statistics Menu Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
Previous Ethernet Statistics Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
Ethernet Statistics - Previous Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Current Ethernet Statistics Menu Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Current Bridge Statistics Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Current Bridge Statistics Menu Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
Current Bridge Statistics Menu Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
Previous Bridge Statistics Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
Previous Bridge Statistics Menu Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
Previous Bridge Statistics Menu Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
System Management Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
Password Control Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36
Password Control Levels for Default Usernames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Mode Selection and Current IP Settings Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . 5-39
Static IP Settings - for IP over Ethernet Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . 5-41
Dynamic IP Settings - for IP over Ethernet Menu Options . . . . . . . . . . . . . . . . . . . . . . . 5-43
Test IP Address Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45
Time/Date Adjust Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-46
Current Baud Rate Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
System Configuration Archive Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49
SNMP Configuration Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-51
SNMP Contact Information Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-52
61179605L5-5B
xi
Total Access 1240 Installation and Maintenance Practice
Table 5-39.
Table 5-40.
Table 5-41.
Table 5-42.
Table 5-43.
Table 5-44.
Table 5-45.
Table 5-46.
Table 5-47.
Table 5-48.
Table 5-49.
Table 5-50.
Table 5-51.
Table 5-52.
Table 5-53.
Table 5-54.
Table 5-55.
Table 5-56.
Table 5-57.
Table 5-58.
Table 5-59.
Table 5-60.
Table 5-61.
Table 7-1.
Table B-1.
Table B-2.
Table B-3.
Table B-4.
Table B-5.
xii
SNMP Community Names Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-53
SNMP Trap Hosts Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-55
External Alarms Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-57
External Alarm Severity Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58
Code Download Method Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-59
TFTP Firmware Download Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-61
Restore Factory Defaults Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-63
Reset System Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64
SHDSL Ports Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65
SHDSL Loop 1 Configuration Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67
Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68
Card Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69
SHDSL Loop 1 Provisioning Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71
SHDSL Loop 1 Service State Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72
SHDSL Loop 1 Interface Mode Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-73
SHDSL Loop 1 G.991.2 Annex Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
SHDSL Loop 1 LineProbing Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-76
SHDSL Loop 1 Alarm Threshold Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-78
SHDSL Loop 1 Status Menu Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-80
SHDSL Loop 1 Test Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83
SHDSL Loop 1 Loopback Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-84
SHDSL Loop 1 Remote Loopback Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86
SHDSL Loop 1 Performance Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88
Total Access 1240 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Bridge User Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
VLANPORTSETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
SNTPCSETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
LocSTUCardProvisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
LocSTULineProvisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
61179605L5-5B
Section 1
Introduction
GENERAL
This practice is an installation and maintenance guide for the ADTRAN Total Access® 1240
2-wire/4-wire Single-pair High-speed Digital Subscriber Line (SHDSL) Digital Subscriber Line
Access Multiplexer (DSLAM). Figure 1-1 illustrates the Total Access 1240 (P/N 1179605L5)
front panel.
Figure 1-1. Total Access 1240 Front Panel
Description
The Total Access 1240 is a 2-wire/4-wire SHDSL mini-DSLAM, consisting of 24 ports fed by a
single 10/100Base-T Ethernet port.
The Total Access 1240 integrates both the SHDSL ports and the Ethernet port onto a single
Printed Circuit Board (PCB) assembly and is powered by –48 VDC. SHDSL port connections
are made through a 50-pin amphenol connector. Ethernet connections are made through an
RJ-45 jack. An alarm port and six LEDs are supported. The unit is fully manageable through
the craft port and an SNMP network management workstation.
The Total Access 1240 is rack-mountable and measures 44.45 millimeters (1.75 inches) high
by 438.15 millimeters (17.25 inches) wide by 282.575 millimeters deep (11.125 inches).
Measurements do not include the mounting brackets. The device can be powered using one or
two –48 VDC sources, one for a non-redundant power configuration, two for a redundant
power configuration.
61179605L5-5B
1-1
Total Access 1240 Installation and Maintenance Practice
Features
The basic and security specific features of the Total Access 1240 are listed below.
Basic Features
The basic features of the Total Access 1240, include the following:
• Front access to all connections
• –48 VDC redundant power inputs
• Removable front access fan module
• Provisioning and alarm monitoring through SNMP (SNMPv2c) and local craft interface
(VT-100 Menu System)
• Dedicated Virtual Local Area Network (VLAN) for Inband Management Channel
• 24 subscriber ports (SHDSL)
• Single Ethernet 10/100Base-T uplink
• Four Virtual Circuits (VC) per port
• Strict prioritization ATM Class of Service (COS) is supported on the VCs that are configured
on each SHDSL Port.
• Learning bridge configuration
• Supports 2-wire operation supporting payload data rates of 192 kbps to 2,304 kbps in
increments of 64 kbps
• Supports 4-wire operation supporting payload data rates of 384 (2 × 192) kbps to 4,608
(2 × 2,304) kbps in increments of 128 (2 × 64) kbps
• System Configuration Archive (SCA)
• Supports the following operational environment
– NEBS GR-63-CORE
– ETSI EN 300 019-1-3 Class 3.1E
– ETSI EN 300 386 V1.3.2 (2003-5) for other than telecommunications centres (Class B)
– Temperature Hardened (–40°C to +70°C)
Security Features
The Total Access 1240 offers a number of filters that affect packets at the subscriber ingress
point. The security features are as follows:
• Local Switching: all ingress subscriber packets are forwarded to the network unless local
switching is enabled. This is a per port option.
• Ether-type Filtering: allows the ingress/egress filtering of traffic based on an Ether-type of
IP, PPPoE, or All. Packets that do not meet the provisioned Ether-type are discarded. This
option is on a per VC basis
• Destination MAC Filtering: when enabled, broadcast packets and packets destined to the
Broadband Remote Access Aggregation Server (BRAS) are forwarded. All others are
discarded.
1-2
61179605L5-5B
Section 1, Introduction - General
Front Panel LEDs
There are six LEDs on the front panel of the Total Access 1240 (see Figure 1-2).
Figure 1-2. Front Panel LEDs
When power is applied the Total Access system performs the power up self-tests. Once the
power up self-test is complete, the LEDs reflect the current condition of the hardware. The
Total Access 1240 LEDs, status, and descriptions are provided in Table 1-1.
Table 1-1. Front Panel LEDs
LEDs
Status
Description
POWER
Green
Yellow
Red
Off
Unit is In Service
Unit is Out of Service-Maintenance
Failed self test
No power present on unit
ALARM
Yellow
Red
Off
Minor alarm is being reported from the unit
Major alarm is being reported from the unit
No alarms reported on unit
SHDSL
Green
All SHDSL ports that are provisioned as In Service have
completed the training sequence
At least one SHDSL port that is provisioned as In Service has not
completed the training sequence
No SHDSL ports are provisioned as In Service
Red
Off
ETH
Green
Yellow
Red
Ethernet connected, 100Base-T
Ethernet connected, 10Base-T
Ethernet not connected
TD
Green Flashing
Off
Ethernet transmit traffic
No ethernet transmit traffic
RD
Green Flashing
Off
Ethernet receive traffic
No ethernet receive traffic
61179605L5-5B
1-3
Total Access 1240 Installation and Maintenance Practice
Compliance
The Total Access 1240 complies with the following international standards:
• Safety – UL 60950 Third Edition; EN 60950 with IEC 950 CB Scheme
• ETSI EN 300 386 V1.3.2 (2003-5) for other than telecommunications centres (Class B)
• Environmental
– Operational environment – NEBS GR-63-CORE; ETSI EN 300 019-1-3 Class 3.1E
– Storage – NEBS GR-63-CORE; ETSI EN 300 019-1-1 class 1.1
– Earthquake – NEBS GR-63-CORE, zone 4
– Transportation – NEBS GR-63-CORE; ETSI EN 300 019-1-2 class 2.3
– Acoustic Noise – ETS 300 753 and 2/1056-FAU 104 06
Figure 1-3 displays the compliance labels for the Total Access 1240.
R
950
O.60
CERTIF
IE
CONFO D T
R
S
.2 TND.60950
N/CSA STD
CA ANSI/U . C22
O S TO
L
M
BFB 401 04 R1A
EDN424 - 24 line SHDSL solution
Figure 1-3. Total Access 1240 Compliance Labels
1-4
61179605L5-5B
Section 2
Application Guidelines
INTRODUCTION
The Total Access 1240 operates as a transparent bridge to provide Medium Access Control
(MAC) level bridging for Ethernet-like networks. The number of attached devices can be up to
twenty-four 2-wire SHDSL modems or twelve 4-wire SHDSL modems or some combination
thereof. When operating in the 4-wire SHDSL mode, if 2 wires are unavailable then the entire
4-wire circuit becomes Out of Service.
As shown in Figure 2-1, service providers are positioned to deploy voice, data, and video over
the same connection (triple play type services) using devices such as the Total Access 1240
SHDSL DSLAM.
Set-top
Box
SHDSL
Modem
PVCs
Total Access
1240
Vo
ic
Da
O&
e
ta
o V e VL
M
V
AN
LA
LA
VL
N
N
AN
V id
Ethernet
Switch
Voice
Gateway
PSTN
Router
Management
Server
Video
SP
ISP
Figure 2-1. Total Access 1240 Application
61179605L5-5B
2-1
Total Access 1240 Installation and Maintenance Practice
For security purposes, the unit operates such that Local Switching (Subscriber Port-to-Port
Switching) can be disabled/enabled within the unit. Port-to-Port switching can also be accomplished using an external device such as an Ethernet Aggregation Switch. Destination MAC
address filtering and Ether-type filtering are also implemented.
The Total Access 1240 supports RFC 2684 (RFC 1483) Bridged Protocol Data Unit (PDU) only.
All traffic priorities and queuing are accomplished in the ATM domain (subscriber side) and
later mapped into the Ethernet domain (network side).
The Total Access 1240 takes Ethernet packets and performs a Segmentation And Reassembly
(SAR) function into an RFC 1483 compliant scheme for transmission over the SHDSL loops to
permit broad compatibility with a wide variety of RFC1483 compliant SHDSL modems. The
unit uses four simplified Class of Service (COS) queues. Prioritization for the transmission of
packets is performed by assigning preference to highest priority packets first and moving to
lower priority packets until there is full bandwidth utilization on the subscriber ports.
The unit supports one to four VCs per port (per RFC1483) with one VLAN per VC. To utilize
four VLANs, the subscriber must have an RFC1483 capable modem that supports four VCs.
The Total Access 1240 supports the ITU G.991.2 SHDSL standard as well as the ETSI TS 101
542 (2001-08) standard. Data rates supported on the subscriber side are 192 kbps to 2.312
Mbps (1-pair) and 384 kbps to 4.624 Mbps (2-pair). Rate adaptive SHDSL Mode is planned for
a future software release.
Lineprobing (also known as rate adaption) is supported on a per port basis. This allows
automatic selection of the SHDSL loop rate based on line conditions at the time of the unit
training.
The maximum number of filtering entries that can be created in the system is 1,024. Consequently, the capacity of the MAC table is 1,024 MAC addresses. The MAC Address table is
global per unit. The MAC addresses are learned on the uplink Ethernet port and the
subscriber loops.
2-2
61179605L5-5B
Section 2, Application Guidelines - VLAN Operation
VLAN OPERATION
A VLAN is a switched network that is logically segmented by function, project team, or application, without regard to the physical locations of the customers. Providers that offer multiple
services can utilize several unique VLANs with different services such as one VLAN to provide
Internet access, one VLAN to provide a Public Switched Telephone Network (PSTN), and
several other VLANs to provide data and voice services such as Voice over IP, online games, TV
broadcasting, etc.
The bridge function of the Total Access 1240 provides support for Virtual LANs in order to
create multiple domains in which packets are forwarded. This restricts traffic so that it
remains within the VLAN in which it belongs. All the learning and forwarding in the bridge is
carried out in the context of a VLAN.
The packets within the VLAN are forwarded pursuant to the following:
• Subscriber Side – Ingress
– Condition: The packet has a VLAN tag that is associated with the VC from which the
packet was received.
- The packet is forwarded to the Network Egress point.
– Condition: The packet has a VLAN tag that is inconsistent with the VC from which the
packet was received.
- The packet is discarded.
– Condition: The packet has no VLAN tag.
- The DSLAM tags the packet with the configured VLAN ID and VLAN priority for that
VC.
- The packet is forwarded to the Network Egress point.
• Network Side – Ingress
– Condition: The packet has a VLAN tag that matches one of the VLANs provisioned within
the DSLAM. The DSLAM supports up to 96 individual VLANs.
- The packet is forwarded to the corresponding customer VC egress point.
- When multiple VCs are on the same VLAN, the Total Access 1240 system matches the
packet’s MAC address to those in the MAC Learning Table and forward the packet to
the VC associated with a matching MAC address.
- If there is no corresponding MAC address in the MAC Learning Table, the packet is
forwarded to all VCs on the same VLAN in an attempt to learn the appropriate VC to
which the MAC belongs.
– Condition: The packet has a VLAN tag that does not match one of the VLANs provisioned
within the DSLAM. The DSLAM supports up to 96 individual VLANs.
- The packet is discarded.
– Condition: The packet is untagged.
- If one or more VCs are set to a VLAN of 1 (Native Operation) the Total Access 1240
system matches the packet’s MAC address to those in the MAC Learning Table and
forward the packet to the VC associated with a matching MAC address.
- If no VCs are set to Native Operation, the packet is discarded.
61179605L5-5B
2-3
Total Access 1240 Installation and Maintenance Practice
• Network – Egress
– Every packet is forwarded.
• Subscriber - Egress
– The VLAN tag is removed.
– The packet is forwarded to the VC corresponding to the original VLAN Tag.
A diagram depicting the Total Access 1240 Ingress/Egress points is provided in Figure 2-2.
Total Access 1240
Network
Ingress
Egress
Egress
Ingress
Subscriber
Figure 2-2. Total Access 1240 Ingress and Egress Points
TRAFFIC PRIORITIZATION
The Total Access 1240 supports four traffic priority classifications per VLAN:
• High = CBR
• MidH = VBRrt
• MidL = VBR
• Low = UBR
There are no rate settings for the CBR, VBRrt, and VBR configurations, therefore, these ATM
COS priorities have been redefined, in descending order of priority, as follows:
1. High
2. MidH
3. MidL
4. Low
Traffic prioritization applies to the data that is forwarded to the egress of the subscriber ports.
Any packets that cannot be serviced due to bandwidth limitations are discarded.
In the upstream path (subscriber to network), the Total Access 1240 can optionally set the
VLAN User Priority Bits from 0-7 for untagged traffic causing the data to be tagged with a
VLAN ID and Priority Bits.
2-4
61179605L5-5B
Section 2, Application Guidelines - System Configuration Archive
SYSTEM CONFIGURATION ARCHIVE
The System Configuration Archive (SCA) (see Figure 2-3) is controlled by SNMP or screen
selections to save provisioning information for the Total Access 1240 to a remote TFTP server
for possible system restoration at a later time. In addition to its use for fast recovery of provisioning information, the SCA system can be used to “clone” baseline configurations to new
installations so that only a few specific provisions need to be altered, significantly reducing
initial setup time.
For further information regarding SCA file format and editing the SCA file, reference
“Appendix B, SCA File Format”.
SNMP
Management
PC
File Server
VLAN 246
Ethernet Port
Total Access 1240
Total Access
1240
IP Management
Port (Inband)
Configuration
File
EGRESS
INGRESS
Port 24
Port 23
Port 2
Port 1
SHDSL ports 1-24
Figure 2-3. System Configuration Archive Concept Diagram
61179605L5-5B
2-5
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
2-6
61179605L5-5B
Section 3
Installation
INTRODUCTION
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
CAUTION
Electronic units can be damaged by ESD. When handling a unit,
wear an antistatic discharge wrist strap to prevent damage to electronic components. Place units in antistatic packing material when
transporting or storing. When working on units, always place them
on an approved antistatic mat that is electrically grounded.
After unpacking the Total Access 1240, inspect it for damage. If damage has occurred, file a
claim with the carrier then contact ADTRAN Customer Service. Refer to “Appendix C,
Warranty” for further information. If possible, keep the original shipping container for
returning the Total Access 1240 for repair or for verification of shipping damage.
61179605L5-5B
3-1
Total Access 1240 Installation and Maintenance Practice
Shipping Contents
The shipping container for the Total Access 1240 includes the contents as shown in Table 3-1
Table 3-1. Total Access 1240 Shipping Contents
Description
Part Number
Quantity
Total Access 1240
1179605L5
1
Total Access 1240 Installation and Maintenance Practice
61179605L5-5
1
Cable Assembly, Ground Wire
3125P037@
1
Terminal Block
32024CON10
1
Mounting Bracket, 19-inch
3265540-1@
2
Mounting Bracket, 23-inch
3265540-2@
2
Screw, 8-32 × 1/4
3276003007
4
Screw, 8-32 × 3/16
327611034
4
Cable Tie
3292032
1
Required Tools
• Wire-wrap tool
• #2 phillips-head screwdriver
• Flat-head screwdriver
• Multimeter (ohmmeter and voltmeter)
• Wire strippers
• Side cutters
3-2
61179605L5-5B
Section 3, Installation - Mounting the Total Access 1240
MOUNTING THE TOTAL ACCESS 1240
The Total Access 1240 is shipped with two sets of mounting brackets that accommodate either
a 19-inch or 21-inch rack.
• The mounting brackets used for a 19-inch rack are part number 3265540-1.
• The mounting brackets used for a 23-inch rack are part number 3265540-2.
The mounting brackets provide for flush or mid-mounting configurations. Figure 3-1 shows
the Total Access 1240 mounting bracket installation options. Four screws (supplied with the
unit) are required for mounting the brackets to the system.
F
R
O
N
T
B
A
C
K
Mounting brackets - 19-inch rack
P/N 3265540-1
F
R
O
N
T
B
A
C
K
Mounting brackets - 23-inch rack
P/N 3265540-2
Figure 3-1. Mounting Brackets
61179605L5-5B
3-3
Total Access 1240 Installation and Maintenance Practice
Flush-mount
For flush-mount systems, the Total Access 1240 must be mounted from the front of the rack,
with mounting brackets in the flush-mounting orientation (see Figure 3-2). When flushmounting a Total Access 1240 in the rack, use a #2 phillips-head screwdriver and attach the
mounting brackets to the front set of threaded screw holes with the flanges containing the
slotted rack-mounting holes facing the front of the Total Access 1240.
F
R
O
N
T
B
A
C
K
Using four screws appropriate for the mounting rack and the appropriate screwdriver, secure
the Total Access 1240 in place on the rack.
Flush-mount Orientation
P/N 3265540-1
19-inch Mounting Brackets
P/N 3265540-2
23-inch Mounting Brackets
Figure 3-2. Flush-mount Orientation
3-4
61179605L5-5B
Section 3, Installation - Mounting the Total Access 1240
Mid-mount
For mid-mount systems, the Total Access 1240 must be mounted from the front of the rack,
with mounting brackets in the mid-mounting orientation (see Figure 3-3). For mid-mounting
a Total Access 1240 in the rack, use a #2 phillips-head screwdriver and attach the mounting
brackets to the rear set of threaded screw holes with the flanges containing the slotted rackmounting holes facing the front of the Total Access 1240.
F
R
O
N
T
B
A
C
K
Using four screws appropriate for the mounting rack and the appropriate screwdriver, secure
the Total Access 1240 in place on the rack.
Mid-mount Orientation
P/N 3265540-1
19-inch Mounting Brackets
P/N 3265540-2
23-inch Mounting Brackets
Figure 3-3. Mid-mount Orientation
61179605L5-5B
3-5
Total Access 1240 Installation and Maintenance Practice
GROUND AND POWER CONNECTIONS
The Total Access 1240 provides redundant power inputs. Two sources of –48 VDC must be
provided to use the redundant power feature. The power wire must be 12 to 18 AWG stranded
copper. The ground wire must be 12 to 18 AWG, however, it must be as large or larger than
the wire used for power.
Ground Connection
The Total Access 1240 must be grounded to a reliable grounding source. To connect the
ground wire, perform the following steps:
1. Connect the ground wire (fitted with a loop terminal end) to the ground lug on the front of
the Total Access 1240, as shown in Figure 3-4.
2. Clean the surface of the frame ground source and apply an appropriate antioxidant.
3. Connect the other end of the ground wire to the grounded frame.
4. Using an ohmmeter, verify continuity between the ground lug and a known good frame
ground. The reading should be less than 1 ohm.
Figure 3-4. Ground Connection
3-6
61179605L5-5B
Section 3, Installation - Ground and Power Connections
Power Connection
The Total Access 1240 uses a four-point terminal block (see Figure 3-5) to accept the
–48 VDC and –48 VDC RET leads.
CA
D
8V
-4
-48
V
A
DC
T
RE
B
T
RE
DC
V
B
C
-48
VD
8
4
-
Figure 3-5. Four-point Terminal Block
NOTE
If a non-redundant power configuration is to be implemented, use
the connections marked –48 VDC A and –48 VDC A RET.
To connect the power source, perform the following steps:
1. With the power disconnected at the source, remove approximately 1/4-inch of insulation
from the ends of both power wires.
NOTE
ADTRAN recommends an external fuse rated between 1.5 to 2.0
amps.
2. Using a small flat-head screwdriver, loosen the setscrews on the top of the terminal block.
3. Insert the bare wire into the opening on the front of the terminal block.
4. While holding the wire in place, tighten the setscrew until the wire is secure.
5. Repeat this procedure until all power leads are connected, making sure that the wires are
connected using correct polarity according to the labeling on the unit above the terminal
block.
6. Apply power to the Total Access 1240 and test the voltage and polarity on the terminal
block using the tops of the setscrews as test points.
61179605L5-5B
3-7
Total Access 1240 Installation and Maintenance Practice
Fans/Fan Filter
The Total Access 1240 is shipped with a pre-installed fan module (P/N 1179672L1). The fan
module is located on the right side of the unit and contains two fans (Figure 3-6). The fans
move filtered air (if the filter is installed) into the Total Access 1240 chassis and out through
the exhaust slots on the left side of the chassis.
The fans are monitored by the Total Access 1240 system and are tested during power-up or
when a fan module is installed. If any fan fails, the POWER LED turns red, indicating a selftest failure, and a minor alarm is generates indicating the problem. The fan alarm can be
suppressed using the fan alarm delay for replacement or maintenance of the fan module.
The fans are thermostatically controlled and operate only when necessary. One fan is
activated first and alternates with the other fan to maintain a specified temperature level. If
the temperature continues to rise, both fans operate at the same time. In the event the
temperature remains high, the SHDSL circuits shut down until a safe operating temperature
is reached.
The fan module and fan filter can be replaced in the field.
FAN MODULE
1179672L1
E
L
DU
M6O72L1
N
9
A
F 117
Figure 3-6. Fan Module
3-8
61179605L5-5B
Section 3, Installation - Ground and Power Connections
Ethernet Connection
The Total Access 1240 interfaces with networks through an Ethernet port. Figure 3-7 shows
the location of the Ethernet port.
Ethernet Connection
Figure 3-7. Ethernet Port
The following Ethernet protocols are supported:
• IEEE 802.3, 10/100Base-T
• IEEE 802.1Q
• IEEE 802.1P User Defined VLAN Priority (upstream)
• DHCP Client Mode for Management
• SNMP
• Ethernet frame sizes up to 1,522 bytes
61179605L5-5B
3-9
Total Access 1240 Installation and Maintenance Practice
Alarm Connections
The Total Access 1240 provides an alarm port (see Figure 3-8) with three auxiliary alarm
inputs and three alarm outputs. Alarm inputs are activated by shorting A and B contacts
which causes an alarm event. Alarm input events can be configured to one of four modes:
Load Shedding, Major, Minor, or Critical and can be designated by the user.
Load shedding can be used to reduce loading in the CO if needed. When invoked, load
shedding causes the unit to switch off sealing current and drops the SHDSL loops to eliminate
power consumption in the product. This can be controlled by one of the external alarm inputs
and is automatically activated by the unit if the internal temperature of the unit reaches
115°C. When the units internal temperature decreases to 110°C it returns to normal
operation.
The alarm outputs provide both normally open and normally closed pins (through internal
relay contacts) for proper operation with a variety of alarm panels. Each alarm event generates
an autonomous message that is transmitted through the management VLAN channel to a
monitoring device.
A cable with a high density DB-15 female connector on one end and a stub at the other end is
available (P/N 1196DB901L1) for wire-wrap connections to an alarm panel.
Alarm Connection
Figure 3-8. Alarm Connection
The alarm pinouts are shown in Table 3-2.
Table 3-2. Alarm Pinouts
3-10
Pin
Contact Description
Pin
Contact Description
1
Alarm 3 Input - A
9
Minor Alarm NC
2
Alarm 1 Input - B
10
Major Alarm NC
3
Critical Alarm COM
11
Alarm 2 Input - B
4
Minor Alarm COM
12
Alarm 1 Input - A
5
Major Alarm COM
13
Critical Alarm NO
6
Alarm 3 Input - B
14
Minor Alarm NO
7
Alarm 2 Input - A
15
Major Alarm NO
8
Critical Alarm NC
61179605L5-5B
Section 3, Installation - Ground and Power Connections
SHDSL Connection
The Total Access 1240 provides 24 SHDSL ports on one 50-pin male amphenol connector (see
Figure 3-9). The 24 SHDSL links can be physically bonded in pairs. A maximum of twelve
4-wire SHDSL links are supported per module. SHDSL links are bonded in odd and even
sequential pairs. For example, SHDSL links 1 and 2, 3 and 4, or 9 and 10 can be linked to
form 4-wire SHDSL links.
SHDSL Connection
Figure 3-9. SHDSL 50-pin Male Amphenol Connector
To connect the SHDLS ports, perform the following steps:
1. Connect a 25-pair female-ended amphenol connector to the male-ended amphenol
connector, labeled SHDSL.
2. Tighten the screw (normally provided with the amphenol connector attached to the cable)
on the right side of the amphenol connector.
3. Use the cable tie (provided) placed through the tie bracket (provided) to secure the left side
of the amphenol connector.
The pin assignments for the SHDSL cable pinouts are shown in Table 3-3.
Table 3-3. SHDSL Cable Pinouts
Pair Number
Pins
Pair Number
Pins
1
1, 26
14
14, 39
2
2, 27
15
15, 40
3
3, 28
16
16, 41
4
4, 29
17
17, 42
5
5, 30
18
18, 43
6
6, 31
19
19, 44
7
7, 32
20
20, 45
8
8, 33
21
21, 46
9
9, 34
22
22, 47
10
10, 35
23
23, 48
11
11, 36
24
24, 49
12
12, 36
25
25, 50 Not used
61179605L5-5B
3-11
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
3-12
61179605L5-5B
Section 4
Provisioning Defaults
INTRODUCTION
The Total Access 1240 can be provisioned by a set of menus that are accessible through the
DB-9 port, labeled CRAFT, or through a management VLAN. The initial configuration of the
system must be completed by way of one of these device ports. Once the management VLAN
channel has been established, the system can be remotely managed through Telnet (IP),
SNMP, or Total Access EMS. The Total Access 1240 default settings are shown in Table 4-1
through Table 4-5.
Table 4-1. Bridge User Port Default Provisioning Options
Provisioning Option
Available Options
Circuit ID
29 character string
VPI
0 to 4096
0
VCI
32 to 65536
35
High
Bridge
PRI
MidHigh (MidH)
1
High
MidLow (MidL)
2
MidH
Low
2
MidL
4
Low
Priority (PRI)
(Port) Enabled/Disabled
Enabled
Default Setting
Disabled
Disabled
VLAN ID
61179605L5-5B
1 to 4096
Port
Bridge
VLAN
1
1
101
1
2
102
1
3
103
1
4
104
•••
•••
•••
24
1
193
24
2
194
24
3
195
24
4
196
4-1
Total Access 1240 Installation and Maintenance Practice
Table 4-1. Bridge User Port Default Provisioning Options (Continued)
Provisioning Option
Available Options
Default Setting
VLAN Priority
0 to 7
0
EtherType (ET)
Any
Any
IP
PPPoE
Local Switching (LS)
Enabled
Disabled
Disabled
Destination Mac Filtering (DMF)
Enabled
Disabled
Disabled
Table 4-2. Ethernet Default Provisioning Options
Provisioning Option
Available Options
Default Setting
Duplex Mode
Auto Negotiate
Auto negotiate
Full Duplex
Half Duplex
Speed
Auto Negotiate
Auto negotiate
100Base
10Base
Table 4-3. SNMP Management Default Provisioning Options
Provisioning Option
Available Options
Default Setting
Password Control
Set Login Name
Access Level
Not configured
Read Only
Not configured
Technician
System Administrator
Control Level
Read Only
Not configured
Read-Write
Allow SNMP Security
Management
Enabled
Disabled
Set Idle Logout Time
1 to 60 minutes
10 minutes
Static
Static
Disabled
IP Address
Mode
Dynamic
(Static) IP Address
0–255.0–255.0–255.1–254
192.168.1.1
(Static) Subnet Mask
1–255.0–255.0–255.0
255.255.0.0
4-2
61179605L5-5B
Section 4, Provisioning Defaults - Introduction
Table 4-3. SNMP Management Default Provisioning Options (Continued)
Provisioning Option
Available Options
Default Setting
(Static) Default Gateway
0–255.0–255.0–255.1–254
192.168.1.254
TFTP IP Address
0–255.0–255.0–255.0–255
192.168.1.2
IP VLAN ID
1 (untagged)
1 (untagged)
2 to 4094 (tagged)
Test IP Address
IP Address
0–255.0–255.0–255.0–255
Not configured
Ping Timeout
1–10 seconds
1 second
Number of Pings
1–8 pings
4 pings
Time
HH.MM (24 hour format)
N/A
Date
MM.DD.YY
N/A
SNTP Network Time
Enabled
Disabled
Time/Date
Disabled
SNTP Server Address
0–255.0–255.0–255.0–255
Not configured
SNTP Poll Interval
5 to 60 minutes, in 5-minute
increments
60 minutes
SNTP Time Zone
GMT-12 to GMT+13
GMT
9600 bps
9600 bps
Baud Rate
Baud Rate
19200 bps
38400 bps
Table 4-4. User Port Default Provisioning Options
Provisioning Option
Available Options
Default Setting
In Service
Out of Service-Maintenance
Card Provisioning
Service State
Out of Service-Unassigned
Out of Service-Maintenance
SHDSL Loop Provisioning
Service State
In Service
Out of Service-Maintenance
Out of Service-Unassigned
Out of Service-Maintenance
Interface Mode
2-wire
2-wire
4-wire
Rate
61179605L5-5B
N × 64 kbps, where Ν=3 to 36
2048 kbps (N=32)
4-3
Total Access 1240 Installation and Maintenance Practice
Table 4-4. User Port Default Provisioning Options (Continued)
Provisioning Option
Available Options
Default Setting
G.991.2 Annex
A
B
B
A/B
Lineprobing (PMMS)
Disabled
Disabled
Enabled - Current Condition
Enabled - Worst Case Condition
PMMS Margin
N/A
N/A
CC = N from 0 to 20, in dB
WC = N from –10 to 20, in dB
Loopback Timeout
Disabled
Disabled
1–999 minutes
SNR Margin Alarm Threshold
Disabled
Disabled
1–15 minutes
Loop Attenuation Alarm
Threshold
Disabled
ES 15 Minute Alarm Threshold
Disabled
Disabled
1–127 dB
Disabled
1–900 seconds
SES 15 Minute Alarm
Threshold
Disabled
UAS 15 Minute Alarm
Threshold
Disabled
LOSWS 15 Minute Alarm
Threshold
Disabled
CVC 15 Minute Alarm
Threshold
Disabled
4-4
Disabled
1–900 seconds
Disabled
1–900 seconds
Disabled
1–900 seconds
Disabled
1–65535 errors
61179605L5-5B
Section 4, Provisioning Defaults - Introduction
Table 4-5. SNMP Configuration Default Provisioning Options
Provisioning Option
Available Options
Default Setting
Contact
50-character string
Customer specified
Name
50-character string
Location
50-character string
SNMP Contact Information
SNMP Community Names
Name
52-character string
Private
Public
Read/Write
IP Address
0–255.0–255.0–255.0–255
Not configured
Privileges
Read
Read
Read/Write
SNMP Trap Hosts
Trap Port
1 to 65535
162
IP Address
0–255.0–255.0–255.0–255
Not configured
Version
SNMPv1
SNMPv2
SNMPv2
SNMP Traps Enabled
SNMP Traps Enabled
Yes
Yes
No
External Alarms
Alarm Name
25-character string
Not configured
Alarm Severity
Critical
Minor
Major
Minor
Load shedding
Fan Alarm Delay
Disabled
Disabled
0–15 minutes
61179605L5-5B
4-5
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
4-6
61179605L5-5B
Section 5
User Interface
INTRODUCTION
This section provides detailed information on the following:
• “System Management” on page 5-1
• “Craft Interface” on page 5-1
• “Inband Management Interface” on page 5-2
• “Logging on to the Total Access 1240” on page 5-3
• “Menu Structure” on page 5-4
• “Menu Navigation” on page 5-5
• “Menu Trees” on page 5-6
• “Menu Descriptions” on page 5-9
SYSTEM MANAGEMENT
Total Access 1240 system management and provisioning is facilitated by a series of intuitive
menus that are accessible on a computer screen. The Total Access 1240 provides two methods
for management access:
• “Craft Interface” on page 5-1
• “Inband Management Interface” on page 5-2
Craft Interface
Connection to the Total Access 1240 system menus can be made through the DB-9 connector,
labeled CRAFT (see Figure 5-1), on the front of the Total Access 1240. A DB-9 straight cable is
required.
Craft Port
Figure 5-1. Craft Port Location
61179605L5-5B
5-1
Total Access 1240 Installation and Maintenance Practice
NOTE
The craft port has priority over Telnet session. If there is an active
craft port session, a Telnet session to the Total Access 1240 cannot
be initiated. If there is an active Telnet session and a craft port
session is initiated, the Telnet session is preempted. The Telnet
session is not available until after the user at the craft port logs off
or the auto-logoff occurs (after 10 minutes of inactivity).
NOTE
The craft port is capable of operating at baud rates of 19200 bps
and 38400 bps.
Connecting a Personal Computer Emulating a VT100 Terminal to Total Access 1240
Most personal computers or laptops can run communications software that emulate a VT
terminal. Windows programs such as Terminal or HyperTerminal are two such examples in
the Windows format, but there are many other adequate, commercially available software
packages, virtually all of which allow the PC or laptop to emulate a VT100 terminal. Certain
configuration items must be set on a PC or laptop to act as a VT100 terminal for the Total
Access 1240.
1. Set the parameters of the communications software to the following settings:
• 9600 baud rate
• 8 data bits
• No parity
• 1 stop bit
• No flow control
2. Set the PC for direct connect on the appropriate communications port (as opposed to dial
up connection).
3. Plug the male end of the data cable into the Total Access 1240. Make connection to the PC
or laptop as appropriate for the equipment.
Inband Management Interface
To access the Total Access 1240 through the inband management method, use an appropriate
Telnet client to access the management interface of the Total Access 1240 at the configured IP
address. For more information, refer to “System Management Menu” on page 5-34.
NOTE
A craft port session takes priority over a Telnet session. An active
craft port session must be terminated before a Telnet session can
be successfully started. When a craft port session is initiated, any
active Telnet session is automatically disconnected.
5-2
61179605L5-5B
Section 5, User Interface - Logging on to the Total Access 1240
LOGGING ON TO THE TOTAL ACCESS 1240
To login to the Total Access 1240 system, perform the following steps:
1. Establish the physical connection to the Total Access 1240.
2. If a craft port session is being used, proceed to step 3. If using a Telnet session proceed to
step 4.
3. Press CTRL+R until the Login prompt appears.
The Login screen is displayed in Figure 5-2. The Total Access 1240 system requires the
login name and associated password.
4. Enter the default login name, “ADMIN” (or the configured login name with System
Administrator privileges), and press ENTER.
5. Enter the default password, “PASSWORD” (or the configured password), and press ENTER.
Total Access 1240 - IPoE Fed
Login:
ADMIN
Password: ********
Figure 5-2. Login Screen
NOTE
The Login name and Password fields are case sensitive. The default
values are all uppercase. For more information, refer to “Password
Control Menu” on page 5-36.
61179605L5-5B
5-3
Total Access 1240 Installation and Maintenance Practice
MENU STRUCTURE
The menu structure for the Total Access 1240 is a layered menu tree. Each layer of the menu
tree is displayed as a menu or a screen.
Menu
A menu is a display that provides numbered selections that are used to navigate to related
menus, modify provisioning information, or display information screens. A menu can contain
the following objects:
• Menu Option: A menu option is indicated by a number, which when selected navigates the
display to another menu layer or is used to change the option setting.
• Read-only Field: A read-only field displays information that cannot be changed. The
information displayed in a read-only field can be static or can be automatically updated by
the Total Access 1240.
• Read-write Field: A read-write field displays information that when selected can be
modified.
• Hot Key: A hot key is a key or combination of keys that are assigned to a function
(see Table 5-2). Hot keys are indicated by the required key(s) and a brief description
(i.e., N - Next Port).
Screen
A screen is a display that usually indicates the end of a menu tree path. A screen can contain
the following objects:
• Read-only Field: A read-only field displays information that cannot be changed. The
information displayed in a read-only field can be static or can be automatically updated by
the Total Access 1240.
• Read-write Field: A read-write field displays information that when selected can be
modified.
• Hot Key: A hot key is a key or combination of keys that are assigned to a function
(see Table 5-2). Hot keys are indicated by the required key(s) and a brief description
(i.e., N - Next Port).
5-4
61179605L5-5B
Section 5, User Interface - Menu Navigation
MENU NAVIGATION
Basic menu navigation is accomplished by selecting the desired option number and then
pressing ENTER. To return to the previous menu or screen, press the ESC (escape) key. To
access the System Help screen, press the question mark (?) key, and press ENTER.
Hot Keys
Table 5-1 shows the general keyboard commands and Table 5-2 shows the menu specific hot
keys for the Total Access 1240 system.
Table 5-1. General Keyboard Commands
Keyboard Command
Description
BACKSPACE
This keyboard command is used to delete the character to the left of the
cursor during keyboard input.
ENTER (or Return)
This keyboard command is used to terminate input.
CTRL+R (Control and r)
This keyboard command is used to renew the display.
CTRL+X (Control and x)
This keyboard command is used to force the terminal menu display to the
top level.
ESC
This keyboard command is used to return to the previous menu.
Spacebar
This keyboard command is used to toggle the setting choices for a text
field.
Table 5-2. Menu Specific Hot Keys
Hot Key
Description
Ethernet Statistics
C
This hot key is used to clear the current Ethernet statistics.
J
This hot key is used to jump to the Current or Previous Ethernet statistics screen.
Bridge Statistics
C
This hot key is used to clear the current Bridge statistics.
J
This hot key is used to jump to the Current or Previous Bridge statistics menu.
M
This hot key is used to display the next bridge.
N
This hot key is used to display the next port.
P
This hot key is used to go to the previous port.
SHDSL Provisioning
N
This hot key is used to display the next loop.
P
This hot key is used to display the previous loop.
S
This hot key is used to select a specific loop.
61179605L5-5B
5-5
Total Access 1240 Installation and Maintenance Practice
Table 5-2. Menu Specific Hot Keys (Continued)
Hot Key
Description
System Alarms
A
This hot key is used to acknowledge all alarms.
C
This hot key is used to clear all alarms.
F
This hot key is used to display the first alarm.
L
This hot key is used to display the last alarm.
N
This hot key is used to display the next alarm.
P
This hot key is used to display the previous alarm.
R
This hot key is used to reset all alarm logs.
T
This hot key is used to display alarms in time ascending or descending order.
MENU TREES
There are a number of menu screens designed to aid in the maintenance and troubleshooting
of the Total Access 1240. The Total Access 1240 menu trees (see Figure 5-3 and Figure 5-4)
are visual maps that is used to locate provisioning options.
5-6
61179605L5-5B
Section 5, User Interface - Menu Trees
1. Unit Information
Unit Name
Part Number
Serial Number
Product Revision
Software Revision
1. Bridge Port Provisioning
Bridge Port Summary
2. Bridge Circuit Management
1. Port
2. Bridge
3. Circuit ID
4. VPI
5. VCI
6. Priority
7. Select Destination Mac Filters
8. VLAN ID
9. VLAN Priority
10. Ether Type
11. Local Switching
12. Enabled/Disabled
13. Save Changes
14. Apply to Other Ports
1. Duplex Mode
2. Ethernet Provisioning
2. Speed
3. Ethernet Statistics
4. Bridge Port Statistics
3. System Management
1. Ports to copy to:
2. Apply Provisioning
3. Exit without changes
1. Auto Negotiate
2. Full Duplex
3. Half Duplex
1. Auto Negotiate
2. 100 Base
3. 10 Base
1. Port
2. Bridge
A
1. Configuration
1. Card
1. Service State
2. Restore Factory Defaults
4. SHDSL Ports
2. Provisioning
1. Service State
2. SHDSL
2. Interface Mode
3. Rate
5. System Alarms
4. G.991.2 Annex
5. Lineprobing (PMMS)
6. PMMS Margin
1. In Service
2. Out of Service - Unassigned
3. Out of Service - Maintenance
1. In Service
2. Out of Service - Unassigned
3. Out of Service - Maintenance
1. 2-wire
2. 4-wire
A
B
A/B
1. Disabled
2. Enabled - Current Condition
3. Enabled - Worst Case Cond.
7. Loopback Timeout
6. Contact Information
3. Status
8. Alarm Thresholds
1. Reset Statistics
4. Alarms
1. Local Loopback
5. Test
6. Performance
7. Logoff
2. Remote Loopback
1. Dual-Sided
2. Customer
3. Network
7. Remote Terminal
1. SNR Margin
2. Loop Attenuation
3. ES 15 Minute
4. SES 15 Minute
5. UAS 15 Minute
6. LOSWS 15 Minute
7. CVC 15 Minute
Figure 5-3. Total Access 1240 Main Menu Tree
61179605L5-5B
5-7
Total Access 1240 Installation and Maintenance Practice
1. Password Control
B
2. IP Address
1. Set Passwords
2. Allow SNMP Security Management
3. Set Idle Logout Time
4. Restore Default Passwords
IP Feed
2. Mode
1. Static
2. Dynamic
(Static IP Settings)
3. Configure IP
3. Test IP Address
4. Time/ Date
5. Baud Rate
6. System Configuration Archive
1. IP Address
2. Ping Timeout
3. Number of Pings
4. Start Ping
5. Start Traceroute
2. Community Names
3. Trap Hosts
4. Traps Enabled
1. Alarm 1
2. Alarm 2
3. Alarm 3
4. Severity
5. Severity
6. Severity
7. Fan Alarm Delay
1. Y-Modem
9. Download New Code
11. Reset System
(Dynamic IP Settings)
1. TFTP IP Address
2. Renew DHCP Lease
3. Reset IP Factory Defaults
4. IP VLAN ID
TFTP Server
TFTP Function
TFTP Filename
Error Status
Update Progress
7. SNMP
10. Restore Factory Defaults
5. Reset IP Factory Defaults
6. IP VLAN ID
1. Adjust Time
2. Adjust Date
3. SNTP: Status
4. SNTP: Server Addr.
5. SNTP: Poll Interval
6. SNTP: Time Zone
1. 9600
2. 19200
3. 38400
1. Contact Information
8. External Alarms
1. IP Address
2. Subnet Mask
3. Default Gateway
4. TFTP IP Address
2. TFTP
1. Restore
2. Exit
1. Reset
2. Exit
1. Contact
2. Name
3. Location
1. Name
2. IP Address
3. Privileges
4. Name
5. IP Address
6. Privileges
7. Name
8. IP Address
9. Privileges
1. IP Address
2. Version
3. IP Address
4. Version
5. IP Address
6. Version
7. Trap Port
1. Download Flash A
2. Download Flash B
3. Exit
TFTP Server:
TFTP Function:
TFTP Filename:
Error Status:
Update Progress:
Figure 5-4. Total Access 1240 System Management Menu Tree
5-8
61179605L5-5B
Section 5, User Interface - Menu Descriptions
MENU DESCRIPTIONS
The Total Access 1240 Main menu (see Figure 5-5) is the access point to all other operations.
The Main menu options have several functions and submenus that identify and provide
access to specific operations and parameters.
Total Access 1240 - IPoE Fed
09/01/05
03:40
Unacknowledged Alarms: None
Total Access 1240
1.
2.
3.
4.
5.
6.
7.
Configuration
Bridge Circuit Management
System Management
User Ports
System Alarms
Contact Information
Logoff
Selection :
'?' - System Help Screen
Figure 5-5. Total Access 1240 Main Menu
The Total Access 1240 Main menu options are shown in Table 5-3.
Table 5-3. Total Access 1240 Main Menu Options
Option
Description
Function
1
Configuration
This option displays the “Configuration Screen” on
page 5-10.
2
Bridge Circuit Management
This option displays the “Bridge Circuit Management
Menu” on page 5-11.
3
System Management
This option displays the “System Management Menu” on
page 5-34.
4
User Ports
This option displays the “SHDSL Ports Menu” on page 565.
5
System Alarms
This option displays the “System Alarm Log Screen” on
page 5-89.
6
Contact Information
This option displays the “Contact Information Screen”
on page 5-90.
7
Logoff
This option is used to end the Total Access 1240 menu
session.
61179605L5-5B
5-9
Total Access 1240 Installation and Maintenance Practice
Configuration Screen
The Configuration screen (see Figure 5-6) displays information about the system. For
instance, the part number can be used to search for related information on the ADTRAN
website or to order additional parts. The software revision can be required when calling
ADTRAN Technical Support.
Total Access 1240 - IPoE Fed
09/01/05
03:40
Unacknowledged Alarms: None
Configuration
Unit Name
Part Number
Serial Number
Product Revision
Software Revision
Total Access 1240
1179605L5
E49A1314
A03.30 (Flash B)
'?' - System Help Screen
Figure 5-6. Configuration Screen
The Configuration screen fields are shown in Table 5-4.
Table 5-4. Configuration Screen Fields
Field
Description
Unit Name
This field displays the unit name of the Total Access 1240.
Part Number
This field displays the part number of the Total Access 1240.
Serial Number
This field displays the serial number of the Total Access 1240.
Production Revision
This field displays the current product revision of the Total
Access 1240.
Software Revision
This field displays the software revision of the Total Access
1240. This field updates automatically when a software
download is completed.
5-10
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Bridge Circuit Management Menu
The Bridge Circuit Management menu (see Figure 5-7) is used to provision and maintain
customer circuits and the Ethernet circuit feeding the system.
Total Access 1240 - IPoE Fed
09/01/05
03:41
Unacknowledged Alarms: None
Bridge Circuit Management
1.
2.
3.
4.
Bridge Port Provisioning
Ethernet Provisioning
Ethernet Statistics
Bridge Port Statistics
Selection:
'?' - System Help Screen
Figure 5-7. Bridge Circuit Management Menu
The Bridge Circuit Management menu options are shown in Table 5-5.
Table 5-5. Bridge Circuit Management Menu
Option
Description
Function
1
Bridge Port Provisioning
This option displays the “Bridge Port Summary Screen”
on page 5-12.
2
Ethernet Provisioning
This option displays the “Ethernet Provisioning Menu”
on page 5-23.
3
Ethernet Statistics
This option displays the “Current Ethernet Statistics
Menu” on page 5-26.
4
Bridge Port Statistics
This option displays the “Current Bridge Statistics
Menu” on page 5-30.
61179605L5-5B
5-11
Total Access 1240 Installation and Maintenance Practice
Bridge Port Summary Screen
The Bridge Port Summary screen (see Figure 5-8) displays all ports and their set parameters
simultaneously. A highlighted port number on this screen indicates a modem as online and
trained. To provision a specific port, navigate to the port with directional arrows, and press
the spacebar (Refer to “Bridge User Port Provisioning Menu” on page 5-13).
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Bridge Port Summary
Port Bridge
VPI
VCI
PRI VLAN VPri
ET
LS DMF
1.
1
0
35
Low
101
0
Any
N
N
1.
2
0
36
Low
102
0
Any
N
N
1.
3
0
37
Low
103
0
Any
N
N
1.
4
0
38
Low
104
0
Any
N
N
2.
1
0
35
Low
105
0
Any
N
N
2.
2
0
36
Low
106
0
Any
N
N
2.
3
0
37
Low
107
0
Any
N
N
2.
4
0
38
Low
108
0
Any
N
N
3.
1
0
35
Low
109
0
Any
N
N
3.
2
0
36
Low
110
0
Any
N
N
3.
3
0
37
Low
111
0
Any
N
N
3.
4
0
38
Low
112
0
Any
N
N
4.
1
0
35
Low
113
0
Any
N
N
4.
2
0
36
Low
114
0
Any
N
N
4.
3
0
37
Low
115
0
Any
N
N
4.
4
0
38
Low
116
0
Any
N
N
Enabled
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Up and Down Arrows to select a port and "Space Bar" to modify
Left & Right Arrows or Tab to page over to other ports
Figure 5-8. Bridge Port Summary Screen
The Bridge Port Summary screen fields are described in Table 5-6.
Table 5-6. Bridge Port Summary Screen Fields
Field
Description
Port
This field displays the current port number.
Bridge
This field displays the current bridge number.
VPI
This field displays the current port VPI setting.
VCI
This field displays the current port VCI setting.
PRI
This field displays the traffic prioritization.
VLAN
This field displays the current VLAN ID.
VPri
This field displays the current VLAN priority for the port.
ET
This field displays the Ether Type value.
LS
This field displays the Local Switching selection (Y/N).
DMF
This field displays Destination MAC Filtering status as being
enabled (Y) or disabled (N).
Enabled
This field displays the enabled/disabled status.
5-12
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Bridge User Port Provisioning Menu
The Bridge User Port Provisioning menu (see Figure 5-9) displays the bridge provisioning for
the port selected from the Bridge Port Provisioning Summary screen (see Figure 5-8 on page 512) and is used to set up and maintain the 24 ports.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Bridge User Port Provisioning
Bridge
VPI
VCI
PRI VLAN VPri
ET
LS DMF
Enabled
1
0
35
Low
101
0
Any
N
N
Yes
2
0
36
Low
102
0
Any
N
N
Yes
3
0
37
Low
103
0
Any
N
N
Yes
4
0
38
Low
104
0
Any
N
N
Yes
1.
2.
3.
4.
5.
6.
7.
Port
1
Bridge
1
Circuit ID
No Circuit ID
VPI
0
VCI
35
Priority
Low
Select Destination Mac Filters
8.
9.
10.
11.
12.
13.
14.
VLAN ID
101
VLAN Priority
0
EtherType
Any
Local Switching N
Enabled/Disabled Yes
Save Changes
SAVED
Apply To Other Ports
Selection:
Up and Down Arrows to select a bridge
Left & Right Arrows or Tab to page over to other bridge ports
Figure 5-9. Bridge User Port Provisioning Menu
The Bridge User Port Provisioning menu fields are described in Table 5-7.
Table 5-7. Bridge User Port Provisioning Menu Fields
Field
Description
Bridge
This field displays the current bridge number.
VPI
This field displays the current port VPI setting.
VCI
This field displays the current port VCI setting.
PRI
This field displays the traffic prioritization.
VLAN
This field displays the current VLAN ID.
VPri
This field displays the current VLAN priority for the port.
ET
This field displays the Ether Type value.
LS
This field displays the Local Switching selection (Y/N).
DMF
This field displays Destination MAC Filtering status as being
enabled (Y) or disabled (N).
Enabled
This field displays the enabled/disabled status.
61179605L5-5B
5-13
Total Access 1240 Installation and Maintenance Practice
The Bridge User Port Provisioning menu options are shown in Table 5-8.
Table 5-8. Bridge User Port Provisioning Menu Options
Option
Description
Function
1
Port
This option is used select a Port (1-24).
2
Bridge
This option is used to assign a bridge number to each
circuit. Each circuit must be assigned to one of four
bridges.
3
Circuit ID
This option is used to assign a text name to the circuit
for use by the provider to identify the circuit.
4
VPI
This option is used to configure each circuit with the
Virtual Path Identifier (VPI) to match the modem that the
customer is using.
5
VCI
This option is used to configure each circuit with the
Virtual Channel Identifier (VCI) to match the modem
that the customer is using.
6
Priority
This option is used to assign strict prioritization to each
circuit. See “Strict Prioritization” on page 5-15.
7
Select Destination Mac Filters
This option displays the “Router Dest Mac Filtering
Menu” on page 5-19.
8
VLAN ID
This option is used to assign a VLAN ID. The VLAN ID is
used to uniquely identify a particular VLAN per IEEE
802.1.Q. The parameter for a VLAN ID is a number
between 1 and 4094.
9
VLAN Priority
This option displays the “VLAN Priority” on page 5-16.
10
Ether Type
This option is used to assign EtherType Filtering which
is selectable as Any, IP, or PPPoE. See “EtherType
Filtering” on page 5-17.
11
Local Switching
This option is used to enable or disable Local Switching.
Selection of this option toggles between Y(es) and N(o).
See “Local Switching” on page 5-18.
12
Enabled/Disabled
This option is used to enable or disable the user port.
13
Save Changes
This option is used to save any changes made to the
Bridge User Port menu.
This option must be used to implement any provisioning
adjustments.
14
5-14
Apply To Other Ports
This option displays the “Apply Provisioning to Ports
Menu” on page 5-21.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Strict Prioritization
There are four available virtual circuits (VCs) per SHDSL loop that can be prioritized on a
strict prioritization basis. This means that any available high priority VC traffic gets queued
into the ATM/SHDSL pipe first followed by traffic at the next highest priority class, and so on,
to the lowest priority class (see Figure 5-10). If a priority class contains no elements, it is
bypassed but always considered for the next queueing sequence. Prioritization only applies to
egress traffic of the subscriber (SHDSL) ports.
Ethernet
VC
Strict Prioritization
Vlan 124
SHDSL
Loop Bandwidth
Vlan 123
Low Priority
Total Access 1240
Port 12 Vlan 515 VC 0/38
MidLow Priority
Port 12 Vlan 514 VC 0/37
Port 12 Vlan 513 VC 0/36
MidHigh Priority
Egress
Port 12 Vlan 512 VC 0/35
Vlan 102
Vlan 101
High Priority
Ingress
As described above Four VCs can be configured on each SHDSL port. There are four priority
settings: High = CBR, MidH = VBRrt, MidL = VBR, and Low = UBR. There are no rate settings
for the cbr, vbrrt, and vbr configurations, therefore, these ATM Class of Service (COS) priorities have been redefined as High, MidH, MidL, and Low priorities.
SHDSL Port 12
Egress
Ingress
Port 24
Port 23
Port 12
Port 2
Port 1
SHDSL ports 1-24
Figure 5-10. Strict Prioritization Concept Diagram
61179605L5-5B
5-15
Total Access 1240 Installation and Maintenance Practice
VLAN Priority
The VLAN Priority option is used to prioritize traffic up to eight levels, with 0 as the lowest and
7 as the highest priority. Table 5-9 lists an example of how traffic types might be organized in
a network implementation.
Table 5-9. Traffic Type Examples
VLAN Priority
Traffic Type
0
Best effort
1
Background
2
Best effort
3
Excellent effort
4
Controlled load
5
Video
6
Voice
NOTE
Actual settings depend on the traffic types used in a particular
network
5-16
61179605L5-5B
Section 5, User Interface - Menu Descriptions
EtherType Filtering
The EtherType Filtering option (see Figure 5-11) allows filtering of the ingress/egress traffic of
the subscriber ports based on the ethertype of IP or PPPoE. This option is applicable on a per
VC basis.
• Packets are filtered based on the following EtherTypes:
– IP
– PPPoE
– Any
Ethernet
Egress
Ingress
• Packets that do not meet the provisioned EtherType are discarded.
Total Access 1240
Either packet
type is
forwarded.
If the packet’s EtherType
is IP, it is forwarded,
if not, it is discarded.
This applies in both directions.
Vlan 124 EthFilt = IP
Vlan 112 EthFilt = Any
Vlan 101 EthFilt = PPPoE
If the packet’s EtherType is
PPPoE, it is forwarded,
if not it is discarded.
This applies in both directions.
Egress
Ingress
Port 24
Port 23
Port 2
Port 1
SHDSL ports 1-24
Figure 5-11. EtherType Filtering Concept Diagram
61179605L5-5B
5-17
Total Access 1240 Installation and Maintenance Practice
Local Switching
Ethernet
Egress
Ingress
The Local Switching option (see Figure 5-12) allows subscriber to subscriber traffic when it is
enabled and both subscribers are on the same VLAN. The data is forwarded to the correct port
as determined by the MAC Learning Table. This option is applied on a per VC basis.
Vlan 124 LS on
Vlan 124 LS on
Vlan 101 LS off
Vlan 101 LS off
Total Access 1240
Egress
Ingress
Port 24
Port 23
Port 2
Port 1
SHDSL ports 1-24
Figure 5-12. Local Switching Concept Diagram
5-18
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Router Dest Mac Filtering Menu
Ethernet
Egress
Ingress
The Select Destination Mac Filters option from the Bridge User Port Provisioning Menu (refer
to “Bridge User Port Provisioning Menu” on page 5-13) allows filtering of ingress traffic of the
subscriber ports based on the configured Mac addresses (see Figure 5-13). Also known as
white listing because traffic other than the configured Mac addresses is discarded and traffic
with the configured Mac addresses is forwarded. Broadcast traffic is forwarded in either case.
Selecting Disabled allows the filtering to be turned off even if the Mac addresses are configured.
Total Access 1240
5 possible Mac entries.
If Dest. Mac of the packet
matches, the packet is forwarded,
otherwise, it is discarded.
Vlan 101 DMF enabled
Vlan 124 DMF enabled
5 possible Mac entries.
If Dest. Mac of the packet
matches, the packet is forwarded,
otherwise, it is discarded.
Egress
Ingress
Port 24
Port 23
Port 2
Port 1
SHDSL ports 1-24
Figure 5-13. Destination Mac Filtering Concept Diagram
61179605L5-5B
5-19
Total Access 1240 Installation and Maintenance Practice
The Router Dest Mac Filtering Menu (see Figure 5-14) is used to select a Port and Bridge,
enable or disable MAC filtering, and set up to 5 MAC Addresses.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Router Dest Mac Filtering
1.
2.
3.
4.
5.
6.
7.
8.
9.
Port
Bridge
MAC Filter
Save Changes
Router MAC Addr
Router MAC Addr
Router MAC Addr
Router MAC Addr
Router MAC Addr
1
2
3
4
5
9
1
Disabled
SAVED
No MAC Address
No MAC Address
No MAC Address
No MAC Address
No MAC Address
Selection :
'J' - Jump to Provisioning
'N' - Next Port
'P' - Previous Port
'?' - System Help Screen
Figure 5-14. Router Dest Mac Filtering Menu
The Router Dest Mac Filtering Menu options are described in Table 5-10.
Table 5-10. Router Dest Mac Filtering Menu Options
Option
Description
Function
1
Port
This option is used to select a port between 1 and 24.
2
Bridge
This option is used to select a bridge between 1 and 4.
3
MAC Filter
This option is used to either enable or disable Mac
filtering.
4
Save Changes
This option is used to save configuration changes made
within this menu.
This option must be used to implement any provisioning
adjustments.
5-9
Router MAC Addr
These options are used to enter non-Multicast MAC
Addresses in Hex format in the following format:
XX:XX:XX:XX:XX:XX
5-20
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Apply Provisioning to Ports Menu
The Apply Provisioning to Ports menu (see Figure 5-15) is used to apply any provisioning
changes to more than one port. Any number of ports can be selected to apply provisioning.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Apply Provisioning to Ports
Warning! This is service affecting!
This will copy the following options to the ports you enter!
Port Bridge
1.
1
1.
2
1.
3
1.
4
VPI
0
0
0
0
VCI
35
36
37
38
PRI
Low
Low
Low
Low
VLAN
101
102
103
104
VPri
0
0
0
0
ET
Any
Any
Any
Any
LS
N
N
N
N
DMF
N
N
N
N
Enabled
Yes
Yes
Yes
Yes
Enter in the form of '1-12,15,24'
1. Ports to copy to: 1-24
2. Apply Provisioning
3. Exit without changes
Selection :
'?' - System Help Screen
Figure 5-15. Apply Provisioning to Ports Menu
CAUTION
This is service affecting.
The Apply Provisioning to Ports menu options are shown in Table 5-11.
Table 5-11. Apply Provisioning to Ports Menu Options
Option
Description
Function
1
Ports to copy to
This option is used to select the specific destination port
numbers that provisioning is to be copied.
2
Apply Provisioning
This option is used to apply provisioning to the ports
selected from option 1.
3
Exit without changes
This option is used to exits the menu without changes.
The Apply Provisioning to Ports menu fields are described in Table 5-12
61179605L5-5B
5-21
Total Access 1240 Installation and Maintenance Practice
Table 5-12. Apply Provisioning to Ports Menu Fields
Field
Description
Port
This field displays the port number to be provisioned.
Bridge
This field displays the bridge number to be provisioned.
VPI
This field displays the VPI assigned to port.
VCI
This field displays the VCI assigned to port.
PRI
This field displays the traffic priority setting.
VLAN
This field displays the VLAN assigned to port.
VPri
This field displays the Virtual Path setting.
ET
This field displays the EtherType filtering assigned to this VC.
LS
This field indicates if Local Switching is enabled or disabled.
DMF
This field indicates if Destination Mac Filtering is enabled or
disabled.
Enabled
This field displays the enabled or disabled status.
5-22
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Ethernet Provisioning Menu
The Ethernet Provisioning menu (see Figure 5-16) is used to configure the Ethernet port. The
Ethernet port is used to connect the Total Access 1240 to a network.
Total Access 1240 - IPoE Fed
09/01/05
03:44
Unacknowledged Alarms: None
Ethernet Provisioning
1. Duplex Mode
2. Speed
Full Duplex
100Base
Selection :
Ethernet Link: Not Active
'?' - System Help Screen
Figure 5-16. Ethernet Provisioning Menu
The Ethernet Provisioning menu options are shown in Table 5-13.
Table 5-13. Ethernet Provisioning Menu Options
Option
Description
Function
1
Duplex Mode
This option displays the “Duplex Mode Menu” on page
5-24.
2
Speed
This option displays the “Speed Mode Menu” on page
5-25.
61179605L5-5B
5-23
Total Access 1240 Installation and Maintenance Practice
Duplex Mode Menu
The Duplex Mode menu (see Figure 5-17) is used to select the duplex mode of the Ethernet
interface.
Total Access 1240 - IPoE Fed
09/01/05
03:44
Unacknowledged Alarms: None
Duplex Mode
-
Full Duplex
1. Auto Negotiate
2. Full Duplex
3. Half Duplex
Selection :
'?' - System Help Screen
Figure 5-17. Duplex Mode Menu
NOTE
The duplex mode displayed in the title indicates the current duplex
mode being viewed or provisioned.
The Duplex Mode menu options are shown in Table 5-14.
Table 5-14. Duplex Mode Menu Options
Option
5-24
Description
Function
1
Auto Negotiate
This option sets the system to automatically detect the
duplex mode of the attached device.
2
Full Duplex
This option sets the Ethernet interface to transmit and
receive simultaneously.
3
Half Duplex
This option sets the Ethernet interface to transmit or
receive at a given time, but not simultaneously.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Speed Mode Menu
The Speed Mode menu (see Figure 5-18) provides options to choose the Ethernet speed.
Total Access 1240 - IPoE Fed
09/01/05
03:44
Unacknowledged Alarms: None
Speed Mode
-
100Base
1. Auto Negotiate
2. 100Base
3. 10Base
Selection :
'?' - System Help Screen
Figure 5-18. Speed Mode Menu
NOTE
The speed mode displayed in the title indicates the current speed
mode being viewed or provisioned.
The Speed Mode menu options are shown in Table 5-15.
Table 5-15. Speed Mode - 100Base Menu Options
Option
Description
Function
1
Auto Negotiate
This option sets the system to automatically detect the
speed of the attached device.
2
100Base
This option sets the Ethernet interface to transmit and
receive at 100 mb/s.
3
10Base
This option sets the Ethernet interface to transmit and
receive at 10 mb/s.
61179605L5-5B
5-25
Total Access 1240 Installation and Maintenance Practice
Current Ethernet Statistics Menu
The Current Ethernet Statistics menu (see Figure 5-19) is used to view and reset the current
Ethernet statistics.
Total Access 1240 - IPoE Fed
09/01/05
03:45
Unacknowledged Alarms:
Current Ethernet Statistics
Transmit Statistics
Successfully Transmitted Packets:
Errored Transmitted Packets:
0
0
LinkType is 10Base mode
Ethernet Link is Down
Receive Statistics
Successfully Received Packets:
Errored Received Packets:
Broadcast Received Packets:
Multicast Received Packets:
Received CRC Errors:
0
0
0
0
0
'C' - Clear Current Statistics
'J' - Go to Previous Statistics Screen
'?' - System Help Screen
Figure 5-19. Current Ethernet Statistics Menu
The Current Ethernet Statistics menu fields are shown in Table 5-16.
Table 5-16. Current Ethernet Statistics Menu Fields
Field
Description
Transmit Statistics
Successfully Transmitted Packets
This field displays the number of packets successfully
transmitted from the unit.
Errored Transmitted Packets
This field displays the number of packets transmitted with
errors from the unit.
Receive Statistics
Successfully Received Packets
This field displays the number of packets successfully received
to the unit.
Errored Received Packets
This field displays the number of packets received with errors to
the unit.
Broadcast Received Packets
This field displays the number of packets received by the layer
addressed as broadcast.
Multicast Received Packets
This field displays the number of packets received by the layer
addressed as multicast.
Received CRC Errors
This field displays the number of Cyclic Redundancy Check
(CRC) errors received to unit.
5-26
61179605L5-5B
Section 5, User Interface - Menu Descriptions
The Current Ethernet Statistics menu hot keys are shown in Table 5-17.
Table 5-17. Current Ethernet Statistics Menu Hot Keys
Hot Key
Description
C
This hot key is used to clear the current Ethernet statistics.
J
This hot key displays the “Previous Ethernet Statistics Menu” on page 5-28.
61179605L5-5B
5-27
Total Access 1240 Installation and Maintenance Practice
Previous Ethernet Statistics Menu
The Previous Ethernet Statistics menu (see Figure 5-20) is used to view the previous five 15minute periods of Ethernet statistics.
Unacknowledged Alarms:
15 Minute Periods
96 Time Periods
Successful Tx Packets:
Errored Tx Packets
:
Successful Rx Packets:
Errored Rx Packets
:
Broadcast Rx Packets :
Multicast Rx Packets :
Rx CRC Errors
:
Total Access 1240 - IPoE Fed
INFO
09/01/05
02:18
Previous Ethernet Statistics
Ethernet Port
93 of 96
<---- Oldest
03/29/05
01:30:00
0
0
0
0
0
0
0
03/29/05
01:45:00
0
0
0
0
0
0
0
'C' - Clear Previous Statistics
'J' - Go to Current Statistics Screen
1 - Oldest
2 - 1/4
3 - Middle
4 - 3/4
5 - Newest
'?' - System Help Screen
03/29/05
02:00:00
0
0
0
0
0
0
0
6 - Prev
Newest ---->
03/29/05
02:15:00
0
0
0
0
0
0
0
7 - Next
Figure 5-20. Previous Ethernet Statistics Menu
The Previous Ethernet Statistics menu options located at the bottom of the screen are shown
in Table 5-18.
Table 5-18. Previous Ethernet Statistics Menu Options
Option
5-28
Description
Function
1
Oldest
This option is used to display the oldest 15-minute
period of Ethernet statistics.
2
1/4
This option is used to display the second oldest
15-minute period of Ethernet statistics.
3
Middle
This option is used to display the middle, or third,
15-minute period of Ethernet statistics.
4
3/4
This option is used to display the fourth 15-minute
period of Ethernet statistics.
5
Newest
This option is used to display the newest 15-minute
period of Ethernet statistics.
6
Prev
This option is used to display Ethernet statistics for the
previous port.
7
Next
This option is used to display Ethernet statistics for the
next port.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
The Previous Ethernet Statistics menu fields are described in Table 5-19.
Table 5-19. Ethernet Statistics - Previous Fields
Field
Description
Successful Tx Packets
This field displays the number of packets successfully
transmitted from the unit.
Errored Tx Packets
This field displays the number of packets transmitted with
errors from the unit.
Successful Rx Packets
This field displays the number of packets successfully received
to the unit.
Errored Rx Packets
This field displays the number of packets received with errors to
the unit.
Broadcast Rx Packets
This field displays the number of packets received by the layer
addressed as broadcast.
Multicast Rx Packets
This field displays the number of packets received by the layer
addressed as multicast.
Rx CRC Errors
This field displays the number of Cyclic Redundancy Check
(CRC) errors received to unit.
The Current Ethernet Statistics menu hot keys are shown in Table 5-20.
Table 5-20. Current Ethernet Statistics Menu Hot Keys
Hot Key
Description
C
This hot key is used to clear the previous Ethernet statistics.
J
This hot key displays the “Current Ethernet Statistics Menu” on page 5-26.
61179605L5-5B
5-29
Total Access 1240 Installation and Maintenance Practice
Current Bridge Statistics Menu
The Current Bridge Statistics menu (see Figure 5-21) is used to select a bridge and view and
reset current port statistics.
NOTE
On the Current Bridge Statistics menu, Transmit Statistics refers
to data from the Total Access 1240 to the customer modem, and
Receive Statistics refers to data from the customer modem to the
Total Access 1240.
Unacknowledged Alarms:
Total Access 1240 - IPoE Fed
INFO
Circuit ID: No Circuit ID
Current Bridge Statistics
VC Enabled
Modem Not Trained
Interface Mode: 2-wire
1. Port
2. Bridge
1
1
Selection :
Transmit Statistics
Good Packets:
Bad Packets:
Good Bytes:
Bad Bytes:
ATM Statistics
Tx Cells:
0
0
0
0
Receive Statistics
Good Packets:
Bad Packets:
Good Bytes:
Bad Bytes:
0
0
0
0
0
Rx Cells:
0
'C' - Clear Current Statistics
'J' - Go to Previous Statistics Screen
'M' - Next Bridge
'N' - Next Port
'P' - Previous Port
'?' - System Help Screen
Figure 5-21. Current Bridge Statistics Menu
The Current Bridge Statistics menu options are shown in Table 5-21.
Table 5-21. Current Bridge Statistics Menu Options
Option
Description
Function
1
Port
This option is used to select a port.
2
Bridge
This option is used to select a bridge.
The Current Bridge Statistics menu fields are shown in Table 5-22.
5-30
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-22. Current Bridge Statistics Menu Fields
Field
Description
Transmit Statistics
Good Packets
This field displays the number of good packets successfully
transmitted by the Total Access 1240.
Bad Packets
This field displays the number of bad packets transmitted by
the Total Access 1240.
Good Bytes
This field displays the number of good bytes successfully
transmitted by the Total Access 1240.
Bad Bytes
This field displays the number of bad bytes transmitted with
errors by the Total Access 1240.
Receive Statistics
Good Packets
This field displays the number of good packets successfully
received by the Total Access 1240.
Bad Packets
This field displays the number of bad packets received by the
Total Access 1240.
Good Bytes
This field displays the number of good bytes successfully
transmitted to the Total Access 1240.
Bad Bytes
This field displays the number of bad bytes transmitted to the
Total Access 1240.
ATM Statistics
Tx Cells
This field displays the number of ATM cells transmitted by the
Total Access 1240.
Rx Cells
This option displays the number of ATM cells received by the
Total Access 1240.
The Current Bridge Statistics menu hot keys are shown in Table 5-23.
Table 5-23. Current Bridge Statistics Menu Hot Keys
Hot Key
Description
C
This hot key is used to clear the current bridge statistics.
J
This hot key displays the “Previous Bridge Statistics Menu” on page 5-32.
M
This hot key is used to display the next bridge.
N
This hot key is used to display the next port.
P
This hot key is used to display the previous port.
61179605L5-5B
5-31
Total Access 1240 Installation and Maintenance Practice
Previous Bridge Statistics Menu
The Previous Bridge Statistics menu (see Figure 5-22) is used to view previous bridge
transmit and receive statistics.
Unacknowledged Alarms:
15 Minute Periods
96 Time Periods
Successful Tx Packets:
Errored Tx Packets
:
Successful Tx Bytes :
Errored Tx Bytes
:
Successful Rx Packets:
Errored Rx Packets
:
Successful Rx Bytes :
Errored Rx Bytes
:
ATM Tx Cells
:
ATM Rx Cells
:
Total Access 1240 - IPoE Fed
INFO
09/01/05
02:32
Previous Bridge Statistics
Port: 1 Bridge: 1
93 of 96
<---- Oldest
03/29/05
01:45:00
0
0
0
0
0
0
0
0
0
0
03/29/05
02:00:00
0
0
0
0
0
0
0
0
0
0
03/29/05
02:15:00
0
0
0
0
0
0
0
0
0
0
Newest ---->
03/29/05
02:30:00
0
0
0
0
0
0
0
0
0
0
'C' - Clear Previous Statistics
'M' - Next Bridge
'J' - Go to Current Statistics Screen
'N' - Next Port
'P' - Previous Port
1 - Oldest
2 - 1/4
3 - Middle
4 - 3/4
5 - Newest
6 - Prev 7 - Next
'?' - System Help Screen
Figure 5-22. Previous Bridge Statistics Previous Menu
The Previous Bridge Statistics menu options located at the bottom of the screen are shown in
Table 5-24.
Table 5-24. Previous Bridge Statistics Menu Options
Option
5-32
Description
Function
1
Oldest
This option is used to display the oldest 15-minute
period of bridge statistics.
2
1/4
This option is used to display the second oldest
15-minute period of bridge statistics.
3
Middle
This option is used to display the middle, or third,
15-minute period of bridge statistics.
4
3/4
This option is used to display the fourth 15-minute
period of bridge statistics.
5
Newest
This option is used to display the newest 15-minute
period of bridge statistics.
6
Prev
This option is used to display bridge statistics for the
previous port.
7
Next
This option is used to display bridge statistics for the
next port.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
The Previous Bridge Statistics menu fields are described in Table 5-25.
Table 5-25. Previous Bridge Statistics Menu Fields
Field
Description
Successful Tx Packets
This option displays the number of packets successfully
transmitted from the unit.
Errored Tx Packets
This option displays the number of packets transmitted with
errors from the unit.
Successful Tx Bytes
This option displays the number of bytes successfully
transmitted from the unit.
Errored Tx Bytes
This option displays the number of bytes transmitted with
errors from the unit.
Successful Rx Packets
This option displays the number of packets successfully
received to the unit.
Errored Rx Packets
This option displays the number of packets received with errors
to the unit.
Successful Rx Bytes
This option displays the number of bytes successfully received
from the unit.
Errored Rx Bytes
This option displays the number of bytes received with errors
from the unit.
ATM Tx Cells
This option displays the number of ATM cells transmitted from
the unit.
ATM Rx Cells
This option displays the number of ATM cells received from the
unit.
The Previous Bridge Statistics menu hot keys are shown in Table 5-26.
Table 5-26. Previous Bridge Statistics Menu Hot Keys
Hot Key
Description
C
This hot key is used to clear the previous bridge statistics.
J
This hot key displays the “Current Bridge Statistics Menu” on page 5-30.
M
This hot key is used to display the next bridge.
N
This hot key is used to display the next port.
P
This hot key is used to display the previous port.
61179605L5-5B
5-33
Total Access 1240 Installation and Maintenance Practice
System Management Menu
The System Management menu (see Figure 5-23) is used to manage system wide settings. The
following subsections describe these settings in detail.
Total Access 1240 - IPoE Fed
09/01/05
03:48
Unacknowledged Alarms: None
System Management
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Password Control
IP Address
Test IP Address
Time/Date
Baud Rate
System Configuration Archive
SNMP
External Alarms
Download New Code
Restore Factory Defaults
Reset System
Selection :
'?' - System Help Screen
Figure 5-23. System Management Menu
The System Management menu options are shown in Table 5-27.
Table 5-27. System Management Menu Options
Option
5-34
Description
Function
1
Password Control
This option displays the “Password Control Menu” on
page 5-36.
2
IP Address
This option displays the “Mode Selection and Current IP
Settings Menu” on page 5-39.
3
Test IP Address
This option displays the “Test IP Address Menu” on
page 5-45.
4
Time/Date
This option displays the “Time/Date Adjust Menu” on
page 5-46.
5
Baud Rate
This option displays the “Current Baud Rate Menu” on
page 5-48.
6
System Configuration Archive
This option displays the “System Configuration Archive
Screen” on page 5-49.
7
SNMP
This option displays the “SNMP Configuration Menu” on
page 5-51.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-27. System Management Menu Options (Continued)
Option
Description
Function
8
External Alarms
This option displays the “External Alarms Menu” on
page 5-57.
9
Download New Code
This option displays the “Code Download Method Menu”
on page 5-59.
10
Restore Factory Defaults
This option displays the “Restore Factory Defaults
Menu” on page 5-63.
11
Reset System
This option displays the “Reset System Menu” on
page 5-64.
61179605L5-5B
5-35
Total Access 1240 Installation and Maintenance Practice
Password Control Menu
The Password Control menu (see Figure 5-24) is used to set and modify passwords, logout
times, and restore default passwords.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Password Control
1.
2.
3.
4.
Set Passwords
Allow SNMP security management
Set Idle Logout Time
Restore Default Passwords
None Configured
Disabled
10 minutes
Selection :
'?' - System Help Screen
Figure 5-24. Password Control Menu
The Password Control menu options are shown in Table 5-28.
Table 5-28. Password Control Menu Options
Option
Description
Function
1
Set Passwords
This option displays the “Password Control Levels
Screen” on page 5-37.
2
Allow SNMP security
management
This option is used to enable or disable SNMP security
management.
3
Set Idle Logout Time
This option is used to set the time allowed before an
automatic logout is performed. This option must be set
between 1 and 60 minutes.
4
Restore Default Passwords
This option is used to restore all passwords to the
default settings.
CAUTION
When the Restore Default Passwords option is selected, the password controls automatically restore to the default setting without
additional prompting.
5-36
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Password Control Levels Screen
The Password Control Levels screen (see Figure 5-25) is used to manage User IDs and
associated passwords that access the system.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
User
Read Only
Technician
System Administrator
Password Control Levels
Status
Login
Not Configured
?
Configured
Technician
Configured
ADMIN
Press space bar to set/change login
Figure 5-25. Password Control Levels Screen
the password control levels for a default usernames are shown in Table 5-29.
Table 5-29. Password Control Levels for Default Usernames
Username
Access Level
Control Level
ADMIN
System Administrator
Read-write and password control
READWRITE
Technician
Read-write
READONLY
Read only
Read only
61179605L5-5B
5-37
Total Access 1240 Installation and Maintenance Practice
Set or Change Username or Password
To set or change a username or password, perform the following steps:
1. Navigate to a Username field with the arrow keys.
The Username field displays in reverse video.
2. Press the spacebar to open the field, type a username, and press ENTER.
3. Press the TAB key to navigate to the Password field.
The Password field displays in reverse video.
4. Press the spacebar to open the field, type a password, and press ENTER.
5. Enter the password again when prompted to verify, and press ENTER.
6. Press the TAB key to navigate to the Access Level field.
The Access Level field displays in reverse video.
7. Press the spacebar to change the access level, and press ENTER.
8. Press the TAB key to navigate to the Status field.
The Status field displays in reverse video.
9. Press the spacebar to change the status, and press ENTER.
5-38
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Mode Selection and Current IP Settings Menu
The Mode Selection and Current IP Settings menu (see Figure 5-26) is used to configure IP
settings in order to remotely manage the Total Access 1240 system.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Mode Selection and Current IP Settings
IP Feed
2. Mode
3. Configure IP
IP over Ethernet
Static
IP address
Subnet mask
Default Gateway
TFTP IP address
IP VLAN ID
MAC Address
Receive Packets
Transmit Packets
192.168.1.1
255.255.255.0
192.168.1.254
10.200.200.218
1
00-a0-c8-12-4c-7c
0
7
Selection :
'?' - System Help Screen
Figure 5-26. Mode Selection and Current IP Settings Menu
The Mode Selection and Current IP Settings menu options are shown in Table 5-30.
Table 5-30. Mode Selection and Current IP Settings Menu Options
Option
N/A
2
Description
Function
IP Feed
This field displays the IP Feed setting. The IP Feed is
non-provisionable and is set to IP over Ethernet.
Mode
This option is used to select either Static or Dynamic.
• In Static Mode, the IP address, Subnet mask, and
Default Gateway are set for inband management of
the Total Access 1240.
• In Dynamic Mode, the Total Access 1240 acts as a
Dynamic Host Configuration Protocol (DHCP) client
and a DHCP server is required upstream from the
Total Access 1240.
When a DHCP server is properly configured, the Total
Access 1240 system obtains the IP address, Subnet
mask, and Default Gateway from the server and applies
these settings to the Total Access 1240.
61179605L5-5B
5-39
Total Access 1240 Installation and Maintenance Practice
Table 5-30. Mode Selection and Current IP Settings Menu Options (Continued)
Option
Description
Function
3
Configure IP
Depending on the setting of the Mode option, the
Configure IP option displays one of the following menus:
• “Static IP Settings - for IP over Ethernet Menu” on
page 5-40
• “Dynamic IP Settings - for IP over Ethernet Menu”
on page 5-43
Static IP Settings - for IP over Ethernet Menu
The Static IP Settings - for IP over Ethernet menu (see Figure 5-27) is used to manually
provision all of the IP settings.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Static IP Settings - for IP over Ethernet
1.
2.
3.
4.
5.
6.
IP address
192.168.1.1
Subnet mask
255.255.255.0
Default Gateway
192.168.1.254
TFTP IP address
10.200.200.218
Reset IP Factory Defaults
IP VLAN ID
1
(Vlan = 1 is untagged / 2-4094 is tagged)
MAC Address
00-a0-c8-12-4c-7c
Selection :
'?' - System Help Screen
Figure 5-27. Static IP Settings - for IP Over Ethernet Menu
NOTE
The Media Access Control (MAC) address, which is set at the
factory, is required to configure the DHCP server.
The Static IP Settings - for IP over Ethernet menu options are shown in Table 5-31.
5-40
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-31. Static IP Settings - for IP over Ethernet Menu Options
Option
Description
Function
1
IP address
This options is used to configure the IP address in
decimal dot format (i.e., ###.###.###.###).
2
Subnet mask
This option is used to configure the Subnet Mask in
decimal dot format.
3
Default Gateway
This option is used to configure the Default Gateway.
The Default Gateway is used to forward traffic to a
destination outside of the subnet of the Total Access
1240. The Default Gateway is configured in decimal dot
format.
4
TFTP IP address
This option is used to configure the TFTP IP address.
The TFTP IP address must be configured to use TFTP for
software upgrade. The TFTP address is configured in
decimal dot format.
5
Reset IP Factory Defaults
This option displays the “Restore IP Factory Defaults
Menu” on page 5-42.
6
IP VLAN ID
This option is used to set the IP VLAN ID.
The IP VLAN ID must be set between 1 and 4094.
Choosing 1 indicates an untagged VLAN ID. Choosing
between 2 and 4094 indicates a tagged VLAN ID.
61179605L5-5B
5-41
Total Access 1240 Installation and Maintenance Practice
Restore IP Factory Defaults Menu
The Restore IP Factory Defaults menu (see Figure 5-28) is used to reset all of the IP factory
defaults.
CAUTION
This is service affecting. If IP factory defaults are enabled remotely,
IP connectivity is lost.
Total Access 1240 - IPoE Fed
09/01/05
03:52
Unacknowledged Alarms: None
Restore IP Factory Defaults
1. Yes - Service Affecting
Selection :
'?' - System Help Screen
Figure 5-28. Restore IP Factory Defaults Menu
5-42
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Dynamic IP Settings - for IP over Ethernet Menu
The Dynamic IP Settings - for IP over Ethernet menu (see Figure 5-29) is used to provision
some of the IP settings. When the Mode option is set to Dynamic, the Total Access 1240
system automatically retrieves the IP address, Subnet mask, and Default Gateway from the
remote DHCP server. The remaining menu items can be provisioned manually.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Dynamic IP Settings - for IP over Ethernet
1.
2.
3.
4.
TFTP IP address
10.200.200.218
Renew DHCP Lease
Reset IP Factory Defaults
IP VLAN ID
1
(Vlan = 1 is untagged / 2-4094 is tagged)
Selection :
'?' - System Help Screen
Figure 5-29. Dynamic IP Settings - for IP over Ethernet Menu
The Dynamic IP Settings - for IP over Ethernet menu options are shown in Table 5-32.
Table 5-32. Dynamic IP Settings - for IP over Ethernet Menu Options
Option
1
Description
Function
TFTP IP address
This option is used to configure the TFTP IP address.
The TFTP IP address must be configured to use TFTP for
software upgrade. The TFTP address is configured in
decimal dot format.
2
Renew DHCP Lease
This option is used to manually renew information from
the DHCP server.
3
Reset IP Factory Defaults
This option displays the “Restore IP Factory Defaults
Menu” on page 5-44.
4
IP VLAN ID
This option is used to configure the IP VLAN ID.
The IP VLAN ID must be set between 1 and 4094.
Choosing 1 indicates an untagged VLAN ID. Choosing
between 2 and 4094 indicates a tagged VLAN ID.
61179605L5-5B
5-43
Total Access 1240 Installation and Maintenance Practice
Restore IP Factory Defaults Menu
The Restore IP Factory Defaults menu (see Figure 5-30) is used to reset all of the IP factory
defaults.
CAUTION
This is service affecting. If IP factory defaults are enabled remotely,
IP connectivity is lost.
Total Access 1240 - IPoE Fed
04/01/05
08:09
Unacknowledged Alarms: None
Restore IP Factory Defaults
1. Yes - Service Affecting
Selection :
'?' - System Help Screen
Figure 5-30. Restore IP Factory Defaults Menu
5-44
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Test IP Address Menu
The Test IP Address menu (see Figure 5-31) is used to test IP configurations. Ping and
Traceroute utilities are includes in this menu.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Test IP Address
1. IP Address
2. Ping Timeout
3. Number of Pings
Not configured
1 secs
4 pings
4. Start Ping
5. Start Traceroute
Selection :
'?' - System Help Screen
Figure 5-31. Test IP Address Menu
The Test IP Address menu options are shown in Table 5-33.
Table 5-33. Test IP Address Menu Options
Option
Description
Function
1
IP Address
This option is used to set the IP address that is to be
tested.
2
Ping Timeout
This option is used to set the number of seconds that
should pass between pings.
3
Number of Pings
This option is used to set the number of pings that are to
be sent during testing of the IP address.
4
Start Ping
This option is used to initiate the ping test.
5
Start Traceroute
This option is used to display the route taken to reach
the IP address that is being tested.
61179605L5-5B
5-45
Total Access 1240 Installation and Maintenance Practice
Time/Date Adjust Menu
The Time/Date Adjust menu (see Figure 5-32) is used to set the system time and date and
configure Simple Network Management Protocol (SNTP) client settings. The time and date
appears on most screens and is also used for performance monitoring displays.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
Time/Date Adjust
1.
2.
3.
4.
5.
6.
Adjust Time
Adjust Date
SNTP: Status
SNTP: Server Addr.
SNTP: Poll Int.
SNTP: Timezone
3:54
09/01/05
ENABLED
192.168.1.100
0
0
Selection :
'?' - System Help Screen
Figure 5-32. Time/Date Adjust Menu
The Time/Date Adjust Menu options are shown in Table 5-34.
Table 5-34. Time/Date Adjust Menu Options
Option
Description
Function
1
Adjust Time
This option is used to set the time in a 24-hour format.
2
Adjust Date
This option is used to set the date in MM/DD/YY format.
3
SNTP: Status
This option is used to enable or disable the SNTP
capabilities.
Simple Network Time Protocol (SNTP) is a connection
less User Datagram Protocol (UDP) used to synchronize
the time with a high-accuracy network time server.
4
SNTP: Server Addr.
This option is used to set the SNTP server address.
The SNTP server address must be entered in decimal
form in the box provided separated by periods.
5
SNTP: Poll Int.
This option is used to set the SNTP poll interval.
The SNTP poll interval is the number of seconds that the
adapter waits between sending SNTP requests and
messages to the SNTP server.
5-46
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-34. Time/Date Adjust Menu Options (Continued)
Option
6
Description
Function
SNTP: Timezone
This option is used to select a specific time zone for
SNTP capabilities.
The time zone is based from the GMT and a valid input
can be offset from –12 to 13 hours from GMT.
Once the IP address of the SNTP server and the desired
poll interval is configured, the Total Access 1240 polls
the specified server IP address from the time-of-day
updates at the specified poll interval.
61179605L5-5B
5-47
Total Access 1240 Installation and Maintenance Practice
Current Baud Rate Menu
The Current Baud Rate menu (see Figure 5-33) displays the current baud rate. The default
management port baud rate is 9600 bps.
Total Access 1240 - IPoE Fed
09/01/05
03:54
Unacknowledged Alarms: None
Current Baud Rate: 9600
Baud Rate change is instantaneous, remember to adjust your terminal
1. 9600
2. 19200
3. 38400
Selection :
'?' - System Help Screen
Figure 5-33. Current Baud Rate Menu
The Current Baud Rate menu options are shown in Table 5-35.
Table 5-35. Current Baud Rate Menu Options
Option
Description
Function
1
9600
This option configures the baud rate to 9600 bps.
2
19200
This option configures the baud rate to 19200 bps.
3
38400
This option configures the baud rate to 38400 bps.
CAUTION
If the baud rate is changed, the rate changes immediately, and the
terminal emulation software must be updated to reflect the change.
5-48
61179605L5-5B
Section 5, User Interface - Menu Descriptions
System Configuration Archive Screen
The System Configuration Archive (SCA) Screen (see Figure 5-34) is used to save/retrieve
provisioning information for the Total Access 1240 to/from a remote TFTP server for possible
system restoration at a later time.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
System Configuration Archive
TFTP Server:
10.200.200.218
TFTP Function: Retrieve file from Server
TFTP Filename:
Error Status:
Update progress:
WARNING! SCA RETRIEVE IS SERVICE AFFECTING!
This process will take several minutes.
Upon completion, the system will reboot and any
open telnet or craft port sessions will be terminated.
Press Space bar to enter TFTP address
Figure 5-34. System Configuration Archive Screen
The System Configuration Archive screen fields are described in Table 5-36.
Table 5-36. System Configuration Archive Screen Fields
Field
Description
TFTP Server
This field is used to enter the IP address of the TFTP Server.
The TFTP address is entered in decimal dot format (i.e.,
###.###.###.###)
TFTP Function
This field is used to enter the function to perform via TFTP.
Available functions are:
• Store file to Server
• Retrieve file from Server
TFTP Filename
61179605L5-5B
This field is used to enter the filename to be stored to or
retrieved from the server via TFTP. The filename must end with
a .cfg extension.
5-49
Total Access 1240 Installation and Maintenance Practice
Table 5-36. System Configuration Archive Screen Fields (Continued)
Field
Description
Error Status
This field displays the status of the TFTP transfer. The Error
Status messages are as follows:
• File Not Found: This status indicates that the TFTP
network server was unable to locate the specified file name
or path in the TFTP Server Filename field.
• Access Violation: This status indicates that the TFTP
network server denied Total Access 1240 access to the
given update filename and path. Verify appropriate
permissions are selected for the specified path.
Update Progress
This field displays the progress of the TFTP transfer. Progress
messages are as follows:
• Contacting Server: This message indicates that an attempt
to establish communication with the TFTP network server
specified by the server address in the TFTP Server IP
Address field is in progress.
• Beginning TFTP Transfer: This message indicates that
communication with the TFTP network server has been
established and the update file is being transferred between
TFTP network server and the Total Access 1240.
• Completed: This message indicates that the Total Access
1240 successfully stored/retrieved the file.
NOTE
Selection between the TFTP Server, TFTP Function, and TFTP
Filename fields is facilitated by using the keyboard up/down arrow
keys.
5-50
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SNMP Configuration Menu
The SNMP Configuration menu (see Figure 5-35) is used to provision community names, trap
hosts, and the traps enabled options, which provide control to manage SNMP remote access to
the system through inband management.
Total Access 1240 - IPoE Fed
09/01/05
03:54
Unacknowledged Alarms: None
SNMP Configuration
1.
2.
3.
4.
Contact Information
Community Names
Trap Hosts
Traps Enabled
Yes
Selection :
'?' - System Help Screen
Figure 5-35. SNMP Configuration Menu
The SNMP Configuration menu options are shown in Table 5-37.
Table 5-37. SNMP Configuration Menu Options
Option
Description
Function
1
Contact Information
This option displays the “SNMP Contact Information
Menu” on page 5-52.
2
Community Names
This option displays the “SNMP Community Names
Menu” on page 5-53.
3
Trap Hosts
This option displays the “SNMP Trap Hosts Menu” on
page 5-55.
4
Traps Enabled
This option toggles between Yes and No to enable or
disable the traps.
61179605L5-5B
5-51
Total Access 1240 Installation and Maintenance Practice
SNMP Contact Information Menu
The SNMP Contact Information menu (see Figure 5-36) contains contact information and can
be customized to reflect any contact, name and location.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
SNMP Contact Information
1. Contact
2. Name
3. Location
ADTRAN, Inc. (256)963-8000
Selection :
'?' - System Help Screen
Figure 5-36. SNMP Contact Information Menu
The SNMP Contact Information menu options are shown in Table 5-38.
Table 5-38. SNMP Contact Information Menu Options
Option
5-52
Description
Function
1
Contact
This option is used to enter a user-specified text string
for the name, phone number, or e-mail address of a
person responsible for the SNMP. Up to 45
alphanumeric characters can be entered in this field,
including spaces and special characters (such as an
underscore).
2
Name
This option is used to enter a user-specified text string
for the name of the Total Access 1240. This name helps
distinguish the Total Access 1240 between different
installations. Up to 45 alphanumeric characters can be
entered in this field, including spaces and special
characters (such as an underscore).
3
Location
This option is used to enter a user-specified text string
for the location of the Total Access 1240. This field is
used to identify the physical location of the unit. Up to
45 alphanumeric characters can be entered in this field,
including spaces and special characters (such as an
underscore).
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SNMP Community Names Menu
The SNMP Community Names menu (see Figure 5-37) is used to establish up to three named
accounts which specify unique IP addresses and privileges for network management. To
restrict SNMP remote access to a single IP address, assign the IP address to a community. An
IP address of 0.0.0.0 provides access from all IP addresses.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
1. Name
2.
3.
4. Name
5.
6.
7. Name
8.
9.
IP Address
Privileges
IP Address
Privileges
IP Address
Privileges
SNMP Community Names
Set Name to 0 to delete Community
private
0.0.0.0
Read
public
0.0.0.0
Read/Write
Not Configured
0.0.0.0
Selection :
'?' - System Help Screen
Figure 5-37. SNMP Community Names Menu
The SNMP Community Names menu options are shown in Table 5-39.
Table 5-39. SNMP Community Names Menu Options
Option
Description
Function
1
Name
This option is used to configure the first SNMP
community. Settings include Private and Public.
2
IP Address
This option is used to configure the first SNMP
community IP address in decimal dot format (i.e.,
###.###.###.###).
3
Privileges
This option is used to configure the first SNMP
community privilege level. Options include Read/Write
and Read.
4
Name
This option is used to configure the second SNMP
community. Settings include Private and Public.
5
IP Address
This option is used to configure the second SNMP
community IP address in decimal dot format (i.e.,
###.###.###.###).
61179605L5-5B
5-53
Total Access 1240 Installation and Maintenance Practice
Table 5-39. SNMP Community Names Menu Options (Continued)
Option
5-54
Description
Function
6
Privileges
This option is used to configure the second SNMP
community privilege level. Options include Read/Write
and Read.
7
Name
This option is used to configure the third SNMP
community. Settings include Private and Public.
8
IP Address
This option is used to configure the third SNMP
community IP address in decimal dot format (i.e.,
###.###.###.###).
9
Privileges
This option is used to configure the third SNMP
community privilege level. Options include Read/Write
and Read.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SNMP Trap Hosts Menu
The SNMP Trap Hosts menu (see Figure 5-38) is used to set multiple IP Addresses (trap destinations) and SNMP versions for notification of a trap. A trap is an automatic alert, or notification, sent to an IP Address. The Total Access 1240 system forwards SNMP traps to all
configured hosts as the traps occur.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
SNMP Trap Hosts
Set IP address to enter Trap Host. Set IP address to D to delete Trap Host
1. IP Address
0.0.0.0
2. Version
SNMPv1
3. IP Address
0.0.0.0
4. Version
SNMPv1
5. IP Address
10.200.200.218
6. Version
SNMPv2
7. Trap Port
162
Selection :
'?' - System Help Screen
Figure 5-38. SNMP Trap Hosts Menu
The SNMP Trap Hosts menu options are shown in Table 5-40.
Table 5-40. SNMP Trap Hosts Menu Options
Option
Description
Function
1
IP Address
This option is used to configure the first SNMP trap host
IP address in decimal dot format (i.e., ###.###.###.###).
2
Version
This option is used to configure the SNMP version for the
first SNMP trap host.
Options include the following:
• SNMPv1
• SNMPv2
3
IP Address
61179605L5-5B
This option is used to configure the second SNMP trap
host IP address in decimal dot format (i.e.,
###.###.###.###).
5-55
Total Access 1240 Installation and Maintenance Practice
Table 5-40. SNMP Trap Hosts Menu Options (Continued)
Option
4
Description
Function
Version
This option is used to configure the SNMP version for the
second SNMP trap host.
Options include the following:
• SNMPv1
• SNMPv2
5
IP Address
This option is used to configure the third SNMP trap
host IP address in decimal dot format (i.e.,
###.###.###.###).
6
Version
This option is used to configure the SNMP version for the
third SNMP trap host.
Options include the following:
• SNMPv1
• SNMPv2
7
Trap Port
This option is used to configure the SNMP trap port.
The trap port is defaulted to port 162 and is
provisionable for cases in which port 162 is blocked.
NOTE
The SNMP version should match the agent used for SNMP on the
network management side.
5-56
61179605L5-5B
Section 5, User Interface - Menu Descriptions
External Alarms Menu
The External Alarms menu (see Figure 5-39) is used to customize the profiles for up to three
external alarms. The alarms can be assigned unique names and an associated severity level
(refer to “External Alarm Severity Menu” on page 5-58).
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
External Alarms
1. Alarm #1 Text - External Alarm Input #1
2. Alarm #2 Text - External Alarm Input #2
3. Alarm #3 Text - External Alarm Input #3
7. Fan Alarm Delay
4. Severity - Minor
5. Severity - Minor
6. Severity - Minor
Disabled
Selection :
'?' - System Help Screen
Figure 5-39. External Alarms Menu
The External Alarms menu options are shown in Table 5-41.
Table 5-41. External Alarms Menu Options
Option
Description
Function
1
Alarm #1 Text
This option is used to enter a 25-character text string for
Alarm #1.
2
Alarm #2 Text
This option is used to enter a 25-character text string for
Alarm #2.
3
Alarm #3 Text
This option is used to enter a 25-character text string for
Alarm #3.
Severity
Options 4 to 6 are used to assign severity levels to each
of the three external alarms. For more information, refer
to “External Alarm Severity Menu” on page 5-58.
Fan Alarm Delay
This option is used to set the delay for amount of time it
takes for an alarm to be generated when the fan module
is removed. This alarm can be set between 0–15
minutes.
4-6
7
61179605L5-5B
5-57
Total Access 1240 Installation and Maintenance Practice
External Alarm Severity Menu
The External Alarm Severity menu (see Figure 5-40) is used to set customized alarm profiles
for each of the five external alarms.
Total Access 1240 - IPoE Fed
09/01/05
03:55
Unacknowledged Alarms: None
External Alarm Severity
1.
2.
3.
4.
Critical
Major
Minor
Load Shedding
Selection :
'?' - System Help Screen
Figure 5-40. External Alarm Severity Menu
The External Alarm Severity menu options are shown in Table 5-42.
Table 5-42. External Alarm Severity Menu Options
Option
Description
Function
1
Critical
This option is used to designate a critical alarm.
2
Major
This option is used to designate a major alarm.
3
Minor
This option is used to designate a minor alarm.
4
Load Shedding
This option is used to designate an alarm that shuts
down SHDSL services.
NOTE
The alarm severity levels are user-defined based on the impact to
customer service.
5-58
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Code Download Method Menu
The Code Download Method menu (see Figure 5-41) displays two methods to download code:
• Y-Modem
• TFTP
CAUTION
Downloading new code is service affecting.
NOTE
The System Management menu TFTP IP address option must be
configured to use TFTP.
Total Access 1240 - IPoE Fed
09/01/05
03:55
Unacknowledged Alarms: None
Code Download Method
1. Y-Modem (Craft Port)
2. TFTP
Selection :
'?' - System Help Screen
Figure 5-41. Code Download Method Menu
The Code Download Method menu options are shown in Table 5-43.
Table 5-43. Code Download Method Menu Options
Option
Description
Function
1
Y-Modem
This option displays the “Y-Modem Download Menu” on
page 5-60.
2
TFTP
This option displays the “TFTP Firmware Download
Screen” on page 5-61.
61179605L5-5B
5-59
Total Access 1240 Installation and Maintenance Practice
Y-Modem Download Menu
The Y-Modem Download menu (see Figure 5-42) is used to download code stored from a
computer to the Total Access 1240 through the craft port.
Total Access 1240 - IPoE Fed
09/01/05
03:56
Unacknowledged Alarms: None
WARNING! THIS IS SERVICE AFFECTING!
If either Flash A or B is selected for update,
service is affected. If Flash B is selected, and code
download completes, the unit will restart itself
to implement the new code.
Y-Modem is the file transfer protocol.
This function cannot be initiated via a telnet
connection (use TFTP instead).
1. Download 1179605L5_A_*** Flash A
2. Download 1179605L5_B_*** Flash B
3. Exit
Selection :
'?' - System Help Screen
Figure 5-42. Y-Modem Download Menu
To download code through the Y-Modem Download menu, perform the following steps:
1. Access the system with System Administrator privileges using a terminal application that
allows file transfers, such as HyperTerminal.
2. Select Download 1179605L5_A_*** Flash A or Download 1179605L5_B_*** Flash B, and press ENTER.
Code upgrades can involve either Flash A or Flash B or both. The Y-Modem receive utility
begins.
3. If using HyperTerminal, select Transfer from the menu, and select Send.
4. Navigate to the appropriate location and choose the file that contains the code to be
downloaded.
CAUTION
The code begins transmitting from the terminal emulation package.
When the download is complete, the unit restarts automatically.
NOTE
If downloading both Flash A and Flash B code, repeat steps 3
through 4, choosing the code not previously downloaded.
5-60
61179605L5-5B
Section 5, User Interface - Menu Descriptions
TFTP Firmware Download Screen
The TFTP Firmware Download screen (see Figure 5-43) is used to download code stored from
a computer to the Total Access 1240 through a TFTP server.
Total Access 1240 - IPoE Fed
Unacknowledged Alarms: None
TFTP Firmware Download
TFTP Server:
10.200.200.218
Get Code for: 1179605L5_A_*** Flash A
TFTP Filename:
Error Status:
Update progress:
Press Space bar to enter TFTP address
Figure 5-43. TFTP Firmware Download Screen
The TFTP Firmware Download screen fields are shown in Table 5-44.
Table 5-44. TFTP Firmware Download Screen Fields
Field
Description
TFTP Server
This field displays the IP address of the TFTP server. The TFTP
IP address must be configured prior to attempting a TFTP
download.
Get Code For
This field displays the module that will be upgraded.
TFTP Filename
This field displays the TFTP filename that will be used to
upgrade the module shown in the Get Code For field. The TFTP
filename must be known and must match the part number.
61179605L5-5B
5-61
Total Access 1240 Installation and Maintenance Practice
Table 5-44. TFTP Firmware Download Screen Fields (Continued)
Field
Description
Update Progress
This field displays the progress of the TFTP download. Progress
messages are as follows:
• Contacting Server: This message indicates that an attempt
to establish communication with the TFTP network server
specified by the server address in the TFTP Server IP
Address field is in progress.
• Beginning TFTP Transfer: This message indicates that
communication with the TFTP network server has been
established and the update file is being transferred between
TFTP network server and the Total Access 1240.
• Completed: This message indicates that the Total Access
1240 successfully received the update file.
Error Status
This field displays the status of the TFTP download. The Error
Status messages are as follows:
• File Not Found: This status indicates that the TFTP network
server was unable to locate the specified file name or path
in the TFTP Server Filename field.
• Access Violation: This status indicates that the TFTP
network server denied Total Access 1240 access to the
given update filename and path. Verify appropriate
permissions are selected for the specified path.
NOTE
Selection between the TFTP Server, Get Code For, and TFTP Filename
fields is facilitated by using the keyboard UP/DOWN ARROW keys.
5-62
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Restore Factory Defaults Menu
The Restore Factory Defaults menu (see Figure 5-44) is used to remotely restore the factory
defaults of the system.
CAUTION
This action is service affecting. If the system is accessed remotely
through a static IP address, the system resets and access is lost.
Total Access 1240 - IPoE Fed
09/01/05
01:25
Unacknowledged Alarms: None
Restore Factory Defaults
WARNING! THIS IS SERVICE AFFECTING!
This defaults all TA1240 options EXCEPT Management IP Settings
and the unit will be restarted upon completion.
The restore operation may take several minutes.
1. Restore
2. Exit
Selection :
'?' - System Help Screen
Figure 5-44. Restore Factory Defaults Menu
The Restore Factory Defaults menu options are shown in Table 5-45.
Table 5-45. Restore Factory Defaults Menu Options
Option
Description
Function
1
Restore
This option is used to restore all SNMP settings to the
factory default settings.
2
Exit
This option is used to return to the “System
Management Menu” on page 5-34. The factory defaults
are not restored.
61179605L5-5B
5-63
Total Access 1240 Installation and Maintenance Practice
Reset System Menu
The Reset System menu (see Figure 5-45) is used to remotely reset the system.
CAUTION
This action is service affecting. If the system is accessed remotely
through a static IP address, the system resets and access is lost.
CAUTION
When the Reset System option is selected, the system resets without additional prompting.
Total Access 1240 - IPoE Fed
09/01/05
03:56
Unacknowledged Alarms: None
Reset System
WARNING! THIS IS SERVICE AFFECTING!
This option resets the entire system.
All system parameters will be retained.
Reset occurs immediately.
1. Reset
2. Exit
Selection :
'?' - System Help Screen
Figure 5-45. Reset System Menu
The Reset System menu options are shown in Table 5-46.
Table 5-46. Reset System Menu Options
Option
5-64
Description
Function
1
Reset
This option is used to reboot the Total Access 1240. All
system options are retained.
2
Exit
This option is used to return to the display to the
“System Management Menu” on page 5-34. The system
does not reboot.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SHDSL Ports Menu
The SHDSL Ports menu (see Figure 5-46) is used to provision all SHDSL ports.
09/01/05
03:56
Total Access 1240
SHDSL Ports
1.
2.
3.
4.
5.
6.
7.
Configuration
Provisioning
Status
Alarms
Test
Performance
Remote Terminal
Selection:
'?' - System Help
Figure 5-46. SHDSL Ports Menu
The SHDSL Ports menu options are shown in Table 5-47.
Table 5-47. SHDSL Ports Menu Options
Option
Description
Function
1
Configuration
This option displays the “SHDSL Loop 1 Configuration
Screen” on page 5-66.
2
Provisioning
This option displays the “Provisioning Menu” on page
5-68.
3
Status
This option displays the “SHDSL Loop 1 Status Menu”
on page 5-80.
4
Alarms
This option displays the “Alarm Status Screen” on
page 5-82.
5
Test
This option displays the “SHDSL Loop 1 Test Menu” on
page 5-83.
6
Performance
This option displays the “SHDSL Loop 1 Performance
Screen” on page 5-88.
7
Remote Terminal
This option is used to set a remote terminal. SHDSL
provides an overhead channel (EOC) over which the
Total Access 1240 can configure the NTU (SHDSL
modem).
61179605L5-5B
5-65
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Configuration Screen
The SHDSL Loop 1 Configuration screen (see Figure 5-47) displays information about the
system. For instance, the part number can be used to search for related information on the
ADTRAN website or to order additional parts. The software revision can be required when
calling ADTRAN Technical Support.
09/01/05
03:57
Total Access 1240
SHDSL Loop 1 Configuration
Vendor ID
Part Number
Serial Number
Product Revision
Manufacture Date
CLEI Code
SHDSL Version
Vendor List Number
Vendor Issue Number
Boot Revision
Software Revision
Software Checksum
'N' - Next Loop
:
:
:
:
:
:
:
:
:
:
:
:
LTU
ADTN
1179605L5
E49A1314
A
01
1
1
A01.00
A03.30 (Flash A)
E215
'P' - Prev Loop
'S' - Select Loop
NTU
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
'?' - System Help
Figure 5-47. SHDSL Loop 1 Configuration Screen
NOTE
The Loop number displayed indicates the current loop number
being viewed or provisioned.
There are two descriptors for each SHDSL field:
• LTU – Line Terminating Unit
• NTU – Network Terminating Unit
The SHDLSL Loop 1 Configuration fields are shown in Table 5-48.
5-66
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-48. SHDSL Loop 1 Configuration Fields
Field
LTU Description
NTU Description
Vendor ID
This field displays the unit vendor
ID.
This field displays the modem
vendor ID.
Part Number
This field displays the part
number of the unit.
This field displays the part
number of the modem.
Serial Number
This field displays the serial
number of the unit.
This field displays the serial
number of the modem.
Product Revision
This field displays the current
product revision of the unit.
This field displays the current
product revision of the modem.
Manufacture Date
This field displays the unit
Manufacture Date.
This field displays the modem
Manufacture Date.
CLEI Code
This field displays the Common
Language Equipment Identifier
(CLEI) of the unit.
This field displays the Common
Language Equipment Identifier
(CLEI) of the modem.
SHDSL Version
This field displays the unit SHDSL
Version.
This field displays the modem
SHDSL Version.
Vendor List Number
This field displays the unit Vendor
List Number.
This field displays the modem
Vendor List Number.
Vendor Issue Number
This field displays the unit Vendor
Issue Number.
This field displays the modem
Vendor Issue Number.
Boot Revision
This field displays the unit Boot
Sector Revision.
This field displays the unit Boot
Sector Revision.
Software Revision
This field displays the software
revision of the active unit. This
field updates automatically when
a software download is completed.
This field displays the software
revision of the modem. This field
updates automatically when a
software download is completed.
Software Checksum
This field displays the unit
Software Checksum.
This field displays the modem
Software Checksum.
61179605L5-5B
5-67
Total Access 1240 Installation and Maintenance Practice
Provisioning Menu
The Provisioning menu (see Figure 5-48) is used to set the provisioning for the main circuit
board card or the SHDSL Circuit IDs.
09/01/05
03:57
Total Access 1240
Provisioning
1.
2.
Card
SHDSL
Selection:
'?' - System Help
Figure 5-48. Provisioning Menu
The Provisioning menu options are shown in Table 5-49.
Table 5-49. Provisioning Menu Options
Option
5-68
Description
Function
1
Card
This option displays the “Card Provisioning Menu” on
page 5-69.
2
SHDSL
This option displays the “SHDSL Loop 1 Provisioning
Menu” on page 5-71.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Card Provisioning Menu
The Card Provisioning menu (see Figure 5-49) is used to set the service state of the main
circuit board card. The default value for the Card Service State is Out of Service-Maintenance.
Changes to this service state are reflected on all 24 ports.
09/01/05
03:58
Total Access 1240
Card Provisioning
1.
2.
Service State
= OOS-Maintenance
Restore Factory Defaults
Selection:
'?' - System Help
Figure 5-49. Card Provisioning Menu
The Card Provisioning menu options are shown in Table 5-50.
Table 5-50. Card Provisioning Menu Options
Option
1
Description
Function
Service State
This option is used to select the card service state. The
available service states are as follows:
• In Service – The SHDSL services are available, if
installed, and Link Down and Threshold alarms are
reported.
• Out of Service-Unassigned – No SHDSL services are
available. No Link Down and Threshold alarms are
reported.
• Out of Service-Maintenance – SHDSL services are
available. No Link Down and Threshold alarms are
reported.
2
Restore Factory Defaults
61179605L5-5B
This option displays the “Restore Factory Defaults
Screen” on page 5-70.
5-69
Total Access 1240 Installation and Maintenance Practice
Restore Factory Defaults Screen
The Restore Factory Defaults screen (see Figure 5-50) is used to restore the factory defaults of
the main circuit board card.
CAUTION
This action is service affecting. If the system is accessed remotely
through a static IP address, the system resets and access is lost.
09/01/05
01:34
Total Access 1240
Restore Factory Defaults
WARNING - This may cause service to be interrupted!
This defaults only the SHDSL Ports Provisions.
Do you wish to continue (Y/N)?
'?' - System Help
Figure 5-50. Restore factory Defaults Screen
5-70
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SHDSL Loop 1 Provisioning Menu
The SHDSL Loop 1 Provisioning menu (see Figure 5-51) is used to provision all of the SHDSL
Circuit IDs. A Circuit ID is initially named using the SHDSL Loop 1 Service State Menu option
from the Bridge Port Summary Screen menu.
09/01/05
01:34
Total Access 1240
SHDSL Loop 1 Provisioning
1.
2.
3.
4.
5.
6.
7.
8.
Service State
Interface Mode
Rate
G.991.2 Annex
Lineprobing (PMMS)
PMMS Margin
Loopback Timeout
Alarm Thresholds
:
:
:
:
:
:
:
OOS-Maintenance
2-wire
2304 Kbps (N=36)
B
Disabled
N/A
Disabled
Selection:
'N' - Next Loop
'P' - Prev Loop
'S' - Select Loop
'?' - System Help
Figure 5-51. SHDSL Loop 1 Provisioning Menu
The SHDSL Loop 1 Provisioning menu options available are shown in Table 5-51.
Table 5-51. SHDSL Loop 1 Provisioning Menu Options
Option
Description
Function
1
Service State
This option displays the “SHDSL Loop 1 Service State
Menu” on page 5-72.
2
Interface Mode
This option displays the “SHDSL Loop 1 Interface Mode
Menu” on page 5-73.
3
Rate
This option displays the “SHDSL Loop 1 Rate Screen” on
page 5-74.
4
G.991.2 Annex
This option displays the “SHDSL Loop 1 G.991.2 Annex
Menu” on page 5-75.
5
Lineprobing (PMMS)
This option displays the “SHDSL Loop 1 LineProbing
Menu” on page 5-76.
6
PMMS Margin
This option displays the “SHDSL Loop 1 PMMS Margin
Screen” on page 5-77.
7
Loopback Timeout
This option is used to enable or disable loopbacks. If
enabled, the timeout can be set from 1–99 minutes.
8
Alarm Thresholds
This option displays the “SHDSL Loop 1 LineProbing
Menu” on page 5-76.
61179605L5-5B
5-71
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Service State Menu
The SHDSL Loop 1 Service State menu (see Figure 5-52) is used to set the loop service state.
The default value is Out of Service-Maintenance.
09/01/05
03:58
Total Access 1240
SHDSL Loop 1 Service State
1.
2.
3.
In Service
Out of Service - Unassigned
Out of Service - Maintenance
Selection:
'?' - System Help
Figure 5-52. SHDSL Loop 1 Service State Menu
The SHDSL Loop 1 Service State menu options are shown in Table 5-52.
Table 5-52. SHDSL Loop 1 Service State Options
Option
5-72
Description
Function
1
In Service
This option makes SHDSL services available, if installed,
and Link Down and Threshold alarms are reported.
2
Out of Service-Unassigned
This option makes SHDSL services unavailable, and no
Link Down and Threshold alarms are reported.
3
Out of Service-Maintenance
This option makes SHDSL services available, and no
Link Down and Threshold alarms are reported.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SHDSL Loop 1 Interface Mode Menu
The SHDSL Loop 1 Interface Mode menu (see Figure 5-53) is used to set the interface mode.
The interface mode can be set to either 2-wire or 4-wire. SHDSL transceivers are designed
primarily for duplex operation over mixed gauge 2-wire twisted metallic pairs, however,
optional 4-wire operation is supported for extended reach applications.
09/01/05
03:59
Total Access 1240
SHDSL Loop 1 Interface Mode
1.
2.
2-wire
4-wire
Selection:
'?' - System Help
Figure 5-53. SHDSL Loop 1 Interface Mode Menu
The SHDSL Loop 1 Interface Mode menu options are shown in Table 5-53.
Table 5-53. SHDSL Loop 1 Interface Mode Menu Options
Option
1
Description
Function
2-wire
This option sets the interface mode to single-pair
operation. SHDSL offers rates from 192 kbps to 2.3
Mbps in increments of 64 kbps.
2
4-wire
This option sets the interface mode to dual-pair
operation. SHDSL offers rates from 384 kbps to 4.6
Mbps in increments of 64 kbps.
NOTE
The line rate on both pairs must be the same.
61179605L5-5B
5-73
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Rate Screen
The SHDSL Loop 1 Rate screen (see Figure 5-54) is used to set the rate for the Circuit ID.
09/01/05
03:09
Total Access 1240
SHDSL Loop 1 Rate
Enter a value for N from 3 to 36, where
the payload rate = N x 64 Kbps:
'?' - System Help
Figure 5-54. SHDSL Loop 1 Rate Screen
The rates defined in SHDSL standard G.991.2 are N × 64 kbits/s, where N = 3 (192 kb/s) to
36 (2304 kb/s).
5-74
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SHDSL Loop 1 G.991.2 Annex Menu
The SHDSL Loop 1 G.991.2 Annex menu (see Figure 5-55) is used to select the annex for the
SHDSL loop.
09/01/05
03:10
Total Access 1240
SHDSL Loop 1 G.991.2 Annex
1.
2.
3.
A
B
A/B
Selection:
'?' - System Help
Figure 5-55. SHDSL Loop 1 G.991.2. Annex Menu
The SHDSL Loop 1 G.991.2 Annex menu options are shown in Table 5-54.
Table 5-54. SHDSL Loop 1 G.991.2 Annex Menu Options
Option
Description
Function
1
A
This option is used to specify Annex A. Annex A is used
for North American applications.
2
B
This option is used to specify Annex B. Annex B is used
for European applications.
3
A/B
This option is used to specify that the Total Access 1240
is to auto-detect the setting of the attached device.
61179605L5-5B
5-75
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 LineProbing Menu
The SHDSL Loop 1 LineProbing menu (see Figure 5-56) is used to configure the Total Access
1240 line probe feature which performs a sequence of power measurements on the twisted
pair. From these measurements, the Total Access 1240 determines what the maximum line
rate is that it can connect at.
Another name for line probe is Power Measurement Modulation Session (PMMS). This session
is performed during the handshake or pre-activation phase of the G.SHDSL training
sequence. Once the line probe session is finished, the units will immediately attempt to train.
09/01/05
02:21
Total Access 1240
SHDSL Loop 1 LineProbing
1. Disabled
2. Enabled - Current Condition
3. Enabled - Worst Case Condition
Selection:
'?' - System Help
Figure 5-56. SHDSL Loop 1 LineProbing Menu
The SHDSL Loop 1 LineProbing menu options are shown in
Table 5-55. SHDSL Loop 1 LineProbing Menu Options
Option
5-76
Description
Function
1
Disabled
Line probing is disabled.
2
Enabled - Current Condition
Current Condition specifies that the line probing
sequence should determine the maximum rate it can
run given the current conditions on the line at the time
of measurement.
3
Enabled - Worst Case
Condition
Worst Case Condition specifies that the line probing
sequence should assume that worst case conditions
exist on the line and then determine the maximum rate
at which to run.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SHDSL Loop 1 PMMS Margin Screen
The SHDSL Loop 1 PMMS Margin Screen (see Figure 5-57 and Figure 5-58) is used to specify
the PMMS Margin in units of dB. The PMMS Margin selection modifies the line probe
algorithm to maximize the rate against the specified margin.
09/01/05
03:07
Total Access 1240
SHDSL Loop 1 PMMS Margin
Enter a Current Condition Margin value for N from 0 to 20, in dB
'?' - System Help
Figure 5-57. SHDSL Loop 1 PMMS Margin Screen
09/01/05
03:14
Total Access 1240
SHDSL Loop 1 PMMS Margin
Enter a Worst Case Condition Margin value for N from -10 to 20, in dB
'?' - System Help
Figure 5-58. SHDSL Loop 1 PMMS Margin Screen Worst Case Option
61179605L5-5B
5-77
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Alarm Thresholds Menu
The SHDSL Loop 1 Alarm Thresholds menu (see Figure 5-59) is used to enable, disable, or set
the thresholds for each interval. When set, each threshold dictates the level or number of
alarm counts at which an SNMP trap is sent.
09/01/05
03:10
Total Access 1240
SHDSL Loop 1 Alarm Thresholds
1.
2.
3.
4.
5.
6.
7.
SNR Margin
Loop Attenuation
ES 15 Minute
SES 15 Minute
UAS 15 Minute
LOSWS 15 Minute
CVC 15 Minute
:
:
:
:
:
:
:
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Selection:
'N' - Next Loop
'P' - Prev Loop
'S' - Select Loop
'?' - System Help
Figure 5-59. SHDSL Loop 1 Alarm Thresholds Menu
The SHDSL Loop 1 Alarm Thresholds menu options are described in Table 5-56.
Table 5-56. SHDSL Loop 1 Alarm Threshold Menu Options
Option
5-78
Alarm Threshold
Description
1
SNR Margin
This field is used to enable or disable the Signal to Noise
Ratio Margin.
The SNR Margin sets a threshold from 0 to 15 dB, which
is used to determine alarm status.
The parameters for SNR Margin are 1 to 15 dB.
2
Loop Attenuation
This option is used to enable or disable the Loop
Attenuation setting.
Loop Attenuation is used to set a loop loss value from 1
to 27 dB, which determines alarm status.
The parameters for Loop Attenuation are 1 to 127 dB.
3
ES 15 Minute
This option is used to enable or disable the Errored
Second setting.
ES is a count of 1-second intervals during which one or
more Cyclical Redundancy Check (CRC) anomalies are
declared and/or one or more LOSW defects are declared.
The parameters for ES are 1 to 900 seconds.
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-56. SHDSL Loop 1 Alarm Threshold Menu Options (Continued)
Option
Alarm Threshold
Description
4
SES 15 Minute
This option is used to enable or disable the Severely
Errored Second setting.
SES 15 minute threshold is a count of 1-second
intervals during which at least 50 CRC anomalies are
declared or one or more LOSW defects are declared. 50
CRC anomalies during a 1-second interval are
equivalent to a 30% errored frame rate for a nominal
frame length.
The parameters for SES are 1 to 900 seconds.
5
UAS 15 Minute
This option is used to enable or disable the Unavailable
Second setting.
UAS 15 minute threshold is a count of 1-second
intervals for which the SHDSL line is unavailable. The
SHDSL line becomes unavailable at the onset of 10
contiguous SESs. The 10 SESs are included in the
unavailable time. Once unavailable, the SHDSL line
becomes available at the onset of 10 contiguous seconds
with no SESs. The 10s with no SESs are excluded from
unavailable time.
The parameters for UAS are 1 to 900 seconds.
6
LOSWS 15 Minute
This option is used to enable or disable the Loss of
Synchronization Word Failure setting.
LOSWS 15 minute threshold is a count of 1-second
intervals during which one or more SHDSL LOSW
defects are declared.
The parameters for LOSWS are 1 to 900 seconds.
7
CVC 15 Minute
This option is used to enable or disable the Code
Violation Count setting.
CVC 15 minute threshold is a count of the SHDSL CRC
anomalies occurring during the accumulation period.
The parameters for CVC are 1 to 65535 errors.
61179605L5-5B
5-79
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Status Menu
The SHDSL Loop 1 Status menu (see Figure 5-60) is used to view and reset SHDSL port
status information.
09/01/05
03:03
Total Access 1240
SHDSL Loop 1 Status
General Status : Down
Payload Rate
: N/A
Loopback Status
SNR Margin(dB)
Loop Atten(dB)
ES
SES
UAS
LOSWS
CVC
Interface Mode : 2-wire
:
:
:
:
:
:
:
:
LTU
Inactive
N/A,N/A,N/A
N/A,N/A,N/A
0
0
1647
1647
0
1.
NTU
N/A
N/A,N/A,N/A (Cur,Min,Max)
N/A,N/A,N/A (Cur,Min,Max)
0
0
0
0
0
Reset Statistics
Selection:
'N' - Next Loop
'P' - Prev Loop
'S' - Select Loop
'?' - System Help
Figure 5-60. SHDSL Loop 1 Status Menu
The SHDSL Loop 1 Status menu fields are described in Table 5-57.
Table 5-57. SHDSL Loop 1 Status Menu Fields
Field
LTU Description
NTU Description
General Status
This field displays the status of
the SHDSL loop. Values include
the following:
This field displays the status of
the SHDSL loop. Values include
the following:
• Down
• Down
• Training
• Training
• Handshaking
• Handshaking
• Trained
• Trained
Payload Rate
This field displays the speed of the
data over the SHDSL circuit,
which does not include SHDSL
framing overhead.
This field displays the speed of the
data over the SHDSL circuit,
which does not include SHDSL
framing overhead.
Interface Mode
This field displays the interface
mode. Values include the
following:
This field displays the interface
mode. Values include the
following:
5-80
• 2-wire
• 2-wire
• 4-wire
• 4-wire
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Table 5-57. SHDSL Loop 1 Status Menu Fields (Continued)
Field
LTU Description
NTU Description
Loopback Status
This field displays the loopback
status of the unit.
This field displays the loopback
status of the modem.
SNR Margin (dB)
This field displays the received
signal level compared to noise
level from the unit.
This field displays the received
signal level compared to noise
level from the SHDSL modem.
Loop Atten (dB)
This field displays the received
signal level from the unit
expressed in DB.
This field displays the received
signal level from the SHDSL
modem expressed in DB.
ES
This field displays the running
count of seconds with any CRC
errors from the unit.
This field displays the running
count of seconds with any CRC
errors from the SHDSL modem.
SES
This field displays the running
count of seconds with 832 or more
CRC errors from the unit.
This field displays the running
count of seconds with 832 or more
CRC errors from the SHDSL
modem.
UAS
This field displays the running
count of seconds where link
access is not available from the
unit.
This field displays the running
count of seconds where link
access is not available from the
SHDSL modem.
LOSWS
This field displays the running
count of seconds where the
SHDSL sync word is not detected
from the unit.
This field displays the running
count of seconds where the
SHDSL sync word is not detected
from the SHDSL modem.
CVC
This field displays the running
count of code violations from the
unit.
This field displays the running
count of code violations from the
SHDSL modem.
61179605L5-5B
5-81
Total Access 1240 Installation and Maintenance Practice
Alarm Status Screen
The Alarm Status screen (see Figure 5-61) is used to view and clear the alarm log.
09/01/05
03:11
Total Access 1240
Page 1 of 1
Alarm Status
Total Alarms: 6
Date
Time
Level
Port Description
Status
04/01/05 02:29:59 Major
EQPT Rear Fan Failure
Cleared
04/01/05 02:29:54 Major
EQPT Front Fan Failure
Cleared
04/01/05 02:29:50 Major
EQPT Fan Module Removed
Cleared
04/01/05 02:29:10 Major
EQPT Rear Fan Failure
Active
04/01/05 02:29:10 Major
EQPT Front Fan Failure
Active
04/01/05 02:29:08 Major
EQPT Fan Module Removed
Active
--------------------------->>> END OF ALARM LOG <<<-----------------------------
'?' - System Help
'N' - Next
'P' - Prev
'F' - First
'L' - Last 'C' - Clear
Figure 5-61. Alarm Status Screen
The Alarm Status screen displays the status of each alarm, the port description, the alarm
level, the time of the alarm, and the date the alarm occurred.
5-82
61179605L5-5B
Section 5, User Interface - Menu Descriptions
SHDSL Loop 1 Test Menu
The SHDSL Loop 1 Test menu (see Figure 5-62) is used to set testing for the SHDSL local or
remote loopbacks.
09/01/05
03:14
Total Access 1240
SHDSL Loop 1 Test
1.
2.
Local Loopback
Remote Loopback
: Inactive
: N/A
Selection:
'N' - Next Loop
'P' - Prev Loop
'S' - Select Loop
'?' - System Help
Figure 5-62. SHDSL Loop 1 Test Menu
The SHDSL Loop 1 Test menu options are shown in Table 5-58.
Table 5-58. SHDSL Loop 1 Test Menu Options
Option
Description
Function
1
Local Loopback
This option displays the “SHDSL Loop 1 Local Loopback
Menu” on page 5-84.
2
Remote Loopback
This option displays the “SHDSL Loop 1 Remote
Loopback Menu” on page 5-86.
61179605L5-5B
5-83
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Local Loopback Menu
The SHDSL Loop 1 Local Loopback menu (see Figure 5-63), is used to perform and view local
loopback tests. For troubleshooting purposes, the Total Access 1240 provides three types of
local loopbacks:
• Dual-Sided
• Customer
• Network
09/01/05
03:05
Total Access 1240
SHDSL Loop 1 Local Loopback
1.
2.
3.
Dual-Sided
Customer
Network
Selection:
'N' - Next Loop
'P' - Prev Loop
'S' - Select Loop
'?' - System Help
Figure 5-63. SHDSL Loop 1 Local Loopback Menu
The SHDSL Loop 1 Local Loopback menu options are shown in Table 5-59.
Table 5-59. SHDSL Loop 1 Loopback Menu Options
Option
Description
Function
1
Dual-Sided
This option is used to initiate a dual-sided loopback. For
more information, refer to “Local Dual-Sided Loopback”
on page 5-85.
2
Customer
This option is used to initiate a customer side loopback.
For more information, refer to “Local Customer
Loopback” on page 5-85.
3
Network
This option is used to initiate a network side loopback.
For more information, refer to “Local Network Loopback”
on page 5-85.
5-84
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Local Dual-Sided Loopback
The local dual-sided loopback provides a bidirectional loopback at the Line Termination Unit
(LTU), as shown in Figure 5-64.
LTU
NTU
Figure 5-64. Local Dual-Sided Loopback
Local Customer Loopback
The local customer loopback provides a loopback at the LTU in the customer direction, as
shown in Figure 5-65. An Alarm Indication Signal (AIS) is injected into the network side.
LTU
TX
AIS
NTU
Figure 5-65. Local Customer Loopback
Local Network Loopback
The local network loopback provides a loopback at the LTU in the network direction, as shown
in Figure 5-66. An AIS signal is injected into the customer side.
LTU
NTU
TX AIS
Figure 5-66. Local Network Loopback
61179605L5-5B
5-85
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Remote Loopback Menu
The SHDSL Loop 1 Remote Loopback menu (see Figure 5-67), is used to perform and view
remote loopback tests. For troubleshooting purposes, the Total Access 1240 provides three
types of remote loopbacks:
• Dual-Sided
• Customer
• Network
09/01/05
00:06
Total Access 1240
SHDSL Loop 1 Remote Loopback
1.
2.
3.
Dual-Sided
Customer
Network
Selection:
'N' - Next Loop
'P' - Prev Loop
'S' - Select Loop
'?' - System Help
Figure 5-67. SHDSL Loop 1 Remote Loopback Menu
The SHDSL Loop 1 Remote Loopback menu options are shown in Table 5-60.
Table 5-60. SHDSL Loop 1 Remote Loopback Menu Options
Option
Description
Function
1
Dual-Sided
This option is used to initiate a remote dual-sided
loopback. For more information, refer to “Remote DualSided Loopback” on page 5-87.
2
Customer
This option is used to initiate a remote customer
loopback. For more information, refer to “Remote
Customer Loopback” on page 5-87.
3
Network
This option is used to initiate a remote network
loopback. For more information, refer to “Remote
Network Loopback” on page 5-87.
5-86
61179605L5-5B
Section 5, User Interface - Menu Descriptions
Remote Dual-Sided Loopback
The remote dual-sided loopback provides a bidirectional loopback at the Network Termination
Unit (NTU), as shown in Figure 5-68.
LTU
NTU
Figure 5-68. Remote Dual-Sided Loopback
Remote Customer Loopback
The remote customer loopback provides a loopback at the NTU in the customer direction, as
shown in Figure 5-69. An Alarm Indication Signal (AIS) is injected into the network side.
LTU
NTU
TX AIS
Figure 5-69. Remote Customer Loopback
Remote Network Loopback
The remote network loopback is initiated at the NTU in the network direction, as shown in
Figure 5-70. AIS signal is injected into the customer side.
LTU
NTU
TX
AIS
Figure 5-70. Remote Network Loopback
The initiation or removal of any loopback test does not interfere with any interface not being
tested. Loopbacks can be set by one source and removed by another source. If the SHDSL line
is dropped, or if the NTU is power cycled, all active loopback tests are released.
61179605L5-5B
5-87
Total Access 1240 Installation and Maintenance Practice
SHDSL Loop 1 Performance Screen
The SHDSL Loop 1 Performance screen (see Figure 5-71) provides information on loop errors
in current and previous 15 minute and 24 hour time intervals.
09/01/05
03:15
Total Access 1240
SHDSL Loop 1 Performance
Interface Mode : 2-wire
ES
SES
UAS
LOSWS
CVC
:
:
:
:
:
Cur 15 Min
Prev 15 Min
Cur 24 Hour
Prev 24 Hour
LTU
00000
00000
00025
00025
00000
LTU
00000
00000
00893
00893
00000
LTU
00000
00000
02358
02358
00000
LTU
00000
00000
00000
00000
00000
'N' - Next Loop
NTU
N/A
N/A
N/A
N/A
N/A
'P' - Prev Loop
NTU
N/A
N/A
N/A
N/A
N/A
NTU
N/A
N/A
N/A
N/A
N/A
'S' - Select Loop
NTU
N/A
N/A
N/A
N/A
N/A
'?' - System Help
Figure 5-71. SHDSL Loop 1 Performance Screen
The SHDSL Loop 1 Performance screen fields are described in Table 5-61.
Table 5-61. SHDSL Loop 1 Performance Screen Fields
Field
LTU Description
NTU Description
Interface Mode
This field displays the interface mode.
Values include the following:
This field displays the interface mode.
Values include the following:
• 2-wire
• 2-wire
• 4-wire
• 4-wire
ES
This field displays the number of CRC
errors from the unit.
This field displays the number of CRC
errors from the SHDSL modem.
SES
This field displays the number of SES
errors from the unit.
This field displays the number of SES
errors from the SHDSL modem.
UAS
This field displays the number of UAS
errors from the unit.
This field displays the number of UAS
errors from the SHDSL modem.
LOSWS
This field displays the number of
LOSWS errors from the unit.
This field displays the number of
LOSWS errors from the SHDSL
modem.
CVC
This field displays the number of CVC
errors from the unit.
This field displays the number of CVC
errors from the SHDSL modem.
5-88
61179605L5-5B
Section 5, User Interface - Menu Descriptions
System Alarm Log Screen
The System Alarm Log screen (see Figure 5-72) provides non-volatile storage of system
events. The event logs can be sorted in ascending or descending order.
Total Access 1240 - IPoE Fed
09/01/05
03:07
Unacknowledged Alarms: None
System Alarm Log
Alarms:
1 to 10 of 10
Page:
1 of
1
Date
Time
Level
Description
Status
04/01/05 2:01:41 Info
1
*Active
04/01/05 3:01:34 Info
1
*Active
04/01/05 2:54:11 Info
1
Active
04/01/05 2:38:40 Info
1
Active
04/01/05 2:38:34 Info
0
Active
04/01/05 2:38:30 Info
0
Active
04/01/05 2:38:14 Info
0
Active
04/01/05 2:36:00 Info
Network Feed is IPoE
Active
04/01/05 2:35:47 Info
Alarm Log Reset
Active
---------------------------->>> END OF ALARM LOG <<<----------------------------
Inverse = Active
* = Unacknowledged
Chronology =
(N)ext (P)rev (F)irst (L)ast (C)lear (A)cknowldege (R)eset Descending
Figure 5-72. System Alarm Log Screen
61179605L5-5B
5-89
Total Access 1240 Installation and Maintenance Practice
Contact Information Screen
The Contact Information screen (see Figure 5-73) displays ADTRAN technical support, repair,
and online support contact information.
Total Access 1240 - IPoE Fed
09/01/05
03:16
Unacknowledged Alarms: None
Contact Information
Adtran Technical Support: (800)726-8663
Adtran Repair / CAPS:
(256)963-8722
Online Support:
www.adtran.com
'?' - System Help Screen
Figure 5-73. Contact Information Screen
5-90
61179605L5-5B
Section 6
Maintenance
INTRODUCTION
The Total Access 1240 does not require routine maintenance for normal operation.
ADTRAN does not recommend that repairs be attempted in the field. Repair services can be
obtained by returning the defective unit to ADTRAN. Refer to the “Appendix C, Warranty”
section for further information.
61179605L5-5B
6-1
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
6-2
61179605L5-5B
Section 7
Specifications
INTRODUCTION
Specifications for the Total Access 1240 are detailed in Table 7-1.
Table 7-1. Total Access 1240 Specifications
Specifications
Descriptions
Environmental
Operating Temperature:
–40°C to +70°C
Storage Temperature:
–40°C to +85°C
Relative Humidity:
Maximum Current Draw:
Maximum Heat Dissipation:
95 percent maximum at 50°C, non-condensing
0.625 amps maximum at –48 VDC
30 watts
Physical
Dimensions:
Height: 44.45 millimeters; 1.75 inches
(1 mounting unit)
Width: 438.15 millimeters; 17.25 inches
Depth: 282.575 millimeters; 11.125 inches
Weight:
< 7.5 pounds
Part Number
Total Access 1240:
61179605L5-5B
1179605L5
7-1
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
7-2
61179605L5-5B
Appendix A
Declaration of Conformity
Corporate Office • 901 Explorer Blvd. • P.O. Box 140000 • Huntsville, AL 35814-4000 • (205) 963-8000
Declaration of Conformity
Adtran
901 Explorer Boulevard
Huntsville Alabama, USA
Declares that the product:
TA1240 24 Port 2W/4W SHDSL DSLAM
1179605L5
is in conformity with the following directives and standards;
Electromagnetic Compatibility Directive, 89/336/EEC, as amended by 92/31/EEC, 93/68/EEC,
EN 300 386 V.1.3.2 (2003-05)
Low Voltage Directive, 73/23/EEC and 93/68/EEC
EN60950: 2000
Authorized Signatory
Jeffrey W. Whitmire
Manager, Regulatory Compliance
Date: March 22, 2005
61179605L5-5B
A-1
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
A-2
61179605L5-5B
Appendix B
SCA File Format
SCA FORMAT
The Total Access 1240 System Configuration Archive (SCA) file can be edited according to the
following format and guidelines.
File Format
The top line is a date code used to check compatibility to current software version. Do not
modify this entry.
Bridge User Ports: Settings are in decimal format except for MAC Address which is in Hex
format.
:DATECODE 06/14/05
:BEGIN //isfs/BRIDGEPORTSSETTINGS Internal Filename (Do not Change)
05/10/05 Date Code (Do not Change)
user1b1, Port Identifier (Do not Change)
No Circuit ID, Circuit ID - Text String
0,35,1,1,0,0,0,1, See Table B-1 for fields a, b, c, d, e, f, g, and h
No MAC Address, MAC Address 1 to filter on - xx:xx:xx:xx:xx:xx
No MAC Address, MAC Address 2 to filter on - xx:xx:xx:xx:xx:xx
No MAC Address, MAC Address 3 to filter on - xx:xx:xx:xx:xx:xx
No MAC Address, MAC Address 4 to filter on - xx:xx:xx:xx:xx:xx
No MAC Address, MAC Address 5 to filter on - xx:xx:xx:xx:xx:xx
•
•
•
:END //isfs/BRIDGEPORTSSETTINGS Internal Filename (Do not Change)
61179605L5-5B
B-1
Total Access 1240 Installation and Maintenance Practice
Table B-1. Bridge User Ports
Field
Option
Values
a
VPI - INT
0-4096
b
VCI - INT
32-65535
c
Priority - INT
0-Low
3-MidL
2-MidH
1-High
d
Reserved
Do not Change
e
Ethertype Filtering - INT
0-ANY
1-IP, 2-PPOE
f
Local Switching
0-Disabled
1-Enabled
g
Destination MAC Filtering
0-Disabled
1-Enabled
h
Port
0-Disabled
1-Enabled
VLANPORTSETTINGS: (1 file) (Settings are in decimal)
:BEGIN //isfs/VLANPORTSETTINGS Internal Filename (Do not Change)
06/08/05 Date Code (Do not Change)
1 Management VLAN - INT (1-4094) 1 for untagged
0, 1, 1, 0, 0 See Table B-2 for fields a, b, c, d, and e
...
95, 4, 0, 0, 0 See Table B-2 for fields a, b, c, d, and e
:END //isfs/VLANPORTSETTINGS Internal Filename (Do not Change)
Table B-2. VLANPORTSETTINGS
Field
B-2
Option
Values
a
Port Number
Do not Change
b
VLAN ID
1-4094
c
Old VID
Do not Change
d
VLAN Priority - INT
0-7
e
Traffic type
Do not Change
61179605L5-5B
Appendix B, SCA File Format - SCA Format
SNTPCSETTINGS
:BEGIN //isfs/SNTPCSETTINGS Internal Filename (Do not change)
192.168.1.100;0;0;0; See Table B-3 for fields a, b, c, and d
:END //isfs/SNTPCSETTINGS Internal Filename (Do not change)
Table B-3. SNTPCSETTINGS
Field
Option
Values
a
SNTP Server IP address
Decimal format: XXX.XXX.XXX.XXX
b
Polling Interval
0 = Disabled
1 to 30 in minutes
c
Offset from GMT
–12 = IDLW
–11 = NT
–10 = HST
–9 = AKST
–8 = YDT
–7 = PDT
–6 = MDT
–5 = CDT
–4 = EDT
–3 = BRA
–2 = AT
–1 = WAT
0 = GMT
1 = CET
2 = EET
3 = IDT
4 = USZ3
5 = USZ4
6 = USZ5
7 = WAST
8 = CCT
9 = ROK
10 = KDT
11 = EADT
12 = IDLE
13 = NZDT
d
Flags
Do not Change
LocSTUCardProvisioning: (Values are in hex)
:LocSTUCardProvisioning 1 Internal Variable Name (Do not Change)
C: 1|
2|
3|
4|
5|
6|
7|
8
--------------------------------------7,
0,
61179605L5-5B
0,
0,
0,
0,
0,
a4
Column Header (Do not Change)
Column Separator (Do not Change)
See Table B-4 below by column number
B-3
Total Access 1240 Installation and Maintenance Practice
Table B-4. LocSTUCardProvisioning
Column
Option
Values
1
Number of Options
Do not change
2
Card Service State
0 = SERVICE_STATE_IN_SERVICE
1 = SERVICE_STATE_OOS_UNASSIGNED
2 = SERVICE_STATE
3
Powerdown Timeout
0 = Disabled
1 to 999 = timeout in minutes
4
Fan Alarm Delay
0 = Disabled
1 to 15 = delay in minutes
5-8
RESERVED for Future Use
:LocSTULineProvisioning 24 (Values are in Hex)
: LocSTULineProvisioning 24 Internal Variable Name (Do not Change)
C: 1|
2|
3|
4|
5|
6|
7|
8|
9|
A|
B|
C|
D|
E|
F|
12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| 1D| 1E| 1F| 20|
23| 24| 25| 26| 27 Column Header (Do not Change)
10|
21|
11|
22|
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Column Separator (Do not Change)
26,
0,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20,
0,
0,
0,
0,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0, ad
See Table B-5 below by column number
20,
0,
20,
0,
0,
0,
0,
0,
...
Table B-5. LocSTULineProvisioning
Column
B-4
Option
Values
1
Number of options
Do not change
2
Line Service State
0 = SERVICE _STATE_IN_SERVICE
1 = SERVICE_STATE_OOS_UNASSIGNED
2 = SERVICE_STATE_OOS_MAINTENANCE
3
SHDSL SNR Margin Alarm
Threshold
0 = Disabled
1 to 15 = threshold in dB
4
SHDSL Loop Attenuation Alarm
Threshold
0 = Disabled
1 to 127 = threshold in dB
5
SHDSL Loopback Timeout
0 = Disabled
1 to 4096 = timeout in minutes
6
Unit Mode
0 = STUC
1 = STUR
61179605L5-5B
Appendix B, SCA File Format - SCA Format
Table B-5. LocSTULineProvisioning (Continued)
Column
Option
Values
7
Annex
0=A
1=B
2 = A/B
8
LineProbing
0 = Disabled
1 = Enabled Current Condition
2 = Enabled Worst Case
9
Repeater Mode
0 = Terminator
1 = Repeater
A
M-pair Mode
0 = 2-wire
1 = 4-wire
2 = Mpair
B
Number of Pairs (Mpair mode
only)
2 pairs ONLY
C
Valid Data Slots (Mpair mode
only)
Bit-wise representation of the ports to be physically
bonded:
bit 0 - pair 1
bit 1 - pair 2
bit 2 - pair 3 (NOT VALID)
bit 3 - pair 4 (NOT VALID)
D
Min Line Rate
N = 3 to 36, where rate = N × 64k + 8k
E
Max Line Rate
N = 3 to 36, where rate = N × 64k + 8k
F
Current Line Rate
N = 3 to 36, where rate = N × 64k + 8k
10
Min Sub Rate
N = 0 to 7, where rate = Line Rate + (N × 8k)
11
Max Sub Rate
N = 0 to 7, where rate = Line Rate + (N × 8k)
12
PMMS Margin CC
–10dB to 20dB
13
PMMS Margin WC
–10dB to 20dB
14
Clock Mode
0
1
2
3
15
Framing Mode
0 = Frame Plesio
1 = Frame Sync
2 = Frame Transparent
16
F-bit notifications
bit
bit
bit
bit
61179605L5-5B
=
=
=
=
Plesio
Plesio w/Reference
Sync
Sync Hybrid
3
2
1
0
=
=
=
=
segment defect: 1 = normal, 0 = segd alarm
power status: 1 = normal, 0 = rem loss of power
segment anomaly: 1 = normal, 0 = sega alarm
loss of signal: 1 = normal, 0 = loss of signal
B-5
Total Access 1240 Installation and Maintenance Practice
Table B-5. LocSTULineProvisioning (Continued)
Column
Option
Values
17
Performance Primitive
Notifications
bit
bit
bit
bit
bit
bit
bit
bit
18
SHDSL ES 15 Minute Alarm
Threshold
0 = Disabled
1 to 900 = threshold in seconds
19
SHDSL SES 15 Minute Alarm
Threshold
0 = Disabled
1 to 900 = threshold in seconds
1A
SHDSL UAS 15 Minute Alarm
Threshold
0 = Disabled
1 to 900 = threshold in seconds
1B
SHDSL CVC 15 Minute Alarm
Threshold
0 = Disabled
1 to 65535 = threshold in seconds
1C
SHDSL LOSWS 15 Minute
Alarm Threshold
0 = Disabled
1 to 900 = threshold in seconds
1D
Line Rate Control
0 = STU-C
1 = STU-R
1E
SHDSL OS 15 Minute Alarm
Threshold
0 = Disabled
1 to 900 = threshold in seconds
1F
Outage Auto-Retrain
0 = Disabled
1 = Enabled
20 - 27
7
6
5
4
3
2
1
0
=
=
=
=
=
=
=
=
segment anomaly
CRC anomaly
segment defect
loss of sync word defect
SNR margin defect
loop attenuation defect
loss of sync word failure
tip/ring reversal
Reserved Options for future use
SCA FILE EXAMPLE
Figure B-1 provides an example of an SCA file.
B-6
61179605L5-5B
61179605L5-5B
95, 196,
0, 0, 0
:END //isfs/VLANPORTSETTINGS
:BEGIN //isfs/SNTPCSETTINGS
192.168.1.100;0;0;0;
:END //isfs/SNTPCSETTINGS
:852 START
:LocSTUCardProvisioning 1
C: 1|
2|
3|
4|
5|
6|
7|
8
--------------------------------------7,
0,
0,
0,
0,
0,
0,
0
:LocSTULineProvisioning 24
C: 1|
2|
3|
4|
5|
6|
7|
8|
9|
A|
B|
C|
D|
E|
F| 10| 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| 1D| 1E| 1F| 20| 21| 22| 23| 24| 25| 26| 27
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
26,
2,
0,
0,
0,
0,
1,
0,
0,
0,
2,
0, 20, 20, 20,
0,
0,
0,
0,
2,
1,
e, 12,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0,
0
:852 STOP
...
user24b4,
No Circuit ID,
0,38,0,1,0,0,0,0,
No MAC Address,
No MAC Address,
No MAC Address,
No MAC Address,
No MAC Address,
:END //isfs/BRIDGEPORTSSETTINGS
:BEGIN //isfs/VLANPORTSETTINGS
06/08/05
1
0, 101,
0, 0, 0
...
:DATECODE 07/12/05
:BEGIN //isfs/BRIDGEPORTSSETTINGS
07/06/05
user01b1,
No Circuit ID,
0,35,1,1,0,0,0,0,
No MAC Address,
No MAC Address,
No MAC Address,
No MAC Address,
No MAC Address,
user01b2,
No Circuit ID,
0,36,2,1,0,0,0,0,
No MAC Address,
No MAC Address,
No MAC Address,
No MAC Address,
No MAC Address,
Appendix B, SCA File Format - SCA File Example
Figure B-1. SCA File Example
B-7
Total Access 1240 Installation and Maintenance Practice
This page is intentionally blank.
B-8
61179605L5-5B
Appendix C
Warranty
WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within the warranty period if it does not meet its
published specifications or fails while in service. Warranty information can be found at
www.adtran.com/warranty.
Refer to the following subsections for sales, support, Customer and Product Service (CAPS)
requests, or further information.
ADTRAN Sales
Pricing/Availability:
800-827-0807
ADTRAN Technical Support
Pre-Sales Applications/Post-Sales Technical Assistance:
800-726-8663
Standard hours: Monday - Friday, 7 a.m. - 7 p.m. CST
Emergency hours: 7 days/week, 24 hours/day
ADTRAN Repair/CAPS
Return for Repair/Upgrade:
(256) 963-8722
Repair and Return Address
Contact CAPS prior to returning equipment to ADTRAN.
ADTRAN, Inc.
CAPS Department
901 Explorer Boulevard
Huntsville, Alabama 35806-2807
61179605L5-5B
C-1
®
Carrier Networks Division
901 Explorer Blvd.
Huntsville, AL 35806
Download PDF

advertising