ADTRAN 600 Series Network Card User Manual

Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 1
TOTAL ACCESS 600 SERIES SHDSL IAD
User Interface Guide
4200683L1
4200643L1
4200612L3
4200616L3
4200624L3
SHDSL Total Access 608
SHDSL Total Access 604
SHDSL Total Access 612
SHDSL Total Access 616
SHDSL Total Access 624
April 2002
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 2
Trademarks
Any brand names and product names included in this manual are trademarks,
registered trademarks, or trade names of their respective holders.
Total Access is a registered trademark of ADTRAN, Inc.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN
reserves the right to change the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential
damages or for commercial losses even if ADTRAN has been advised thereof as a
result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
(256) 963-8000
©2002 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 3
Notes provide additional useful information.
Caution signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.
Safety Instructions
When using your telephone equipment, please follow these basic safety
precautions to reduce the risk of fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm.
There is a remote risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of batteries in a fire. They may explode. Check with local
codes for special disposal instructions.
Save These Important Safety Instructions
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 4
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 5
FCC regulations require that the following information be provided in this manual
to the customer:
1. This equipment complies with Part 68 of the FCC rules. On the side of the bottom of this equipment is a label that contains, among other information, the
FCC Registration Number and Ringer Equivalence Number (REN), if applicable, for this equipment. If required, this information must be given to the telephone company.
2. An FCC-compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68compliant. See installation instructions for details.
3. If your telephone equipment (TA 600) causes harm to the telephone network,
the telephone company may discontinue your service temporarily. If possible,
they will notify you in advance. But if advance notice isn’t practical, you will
be notified as soon as possible. You will be advised of your right to file a complaint with the FCC.
4. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. If
they do, you will be given advance notice to give you an opportunity to maintain uninterrupted service.
5. If you experience trouble with this equipment (TA 600), please contact ADTRAN for repair/warranty information. The telephone company may ask you to
disconnect this equipment from the network until the problem has been corrected or until you are sure the equipment is not malfunctioning.
6. This unit contains no user-serviceable parts.
7. The FCC recommends that the AC outlet to which equipment requiring AC
power is to be installed is provided with an AC surge arrester.
8. The REN is used to determine the quantity of devices which may be connected
to the telephone line. Excessive RENs on the telephone line may result in the
devices not ringing in response to an incoming call. In most, but not all areas,
the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
9. The following information may be required when applying to your local telephone company for leased line facilities.
6HUYLFH7\SH
$QDORJ6HUYLFH/LIH/LQH
© 2002, ADTRAN, Inc.
5(162&
),&
862&
%)
/6*6
5-&
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 6
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the
documentation or on the product labeling/markings. The REN assigned to each terminal device indicates
the maximum number of terminals that can be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices should not exceed five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 7
Warranty and Customer Service
ADTRAN will repair and return this product within ten years from the date of shipment if it does not meet
its published specifications or fails while in service. For detailed warranty, repair, and return information
refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure.
Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN.
For service, RMA requests, or further information, contact one of the numbers listed at the end of this
section.
LIMITED PRODUCT WARRANTY
ADTRAN warrants that for ten years from the date of shipment to Customer, all products manufactured by
ADTRAN will be free from defects in materials and workmanship. ADTRAN also warrants that products
will conform to the applicable specifications and drawings for such products, as contained in the Product
Manual or in ADTRAN's internal specifications and drawings for such products (which may or may not be
reflected in the Product Manual). This warranty only applies if Customer gives ADTRAN written notice of
defects during the warranty period. Upon such notice, ADTRAN will, at its option, either repair or replace
the defective item. If ADTRAN is unable, in a reasonable time, to repair or replace any equipment to a
condition as warranted, Customer is entitled to a full refund of the purchase price upon return of the
equipment to ADTRAN. This warranty applies only to the original purchaser and is not transferable
without ADTRAN's express written permission. This warranty becomes null and void if Customer
modifies or alters the equipment in any way, other than as specifically authorized by ADTRAN.
EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE FOREGOING
CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE
EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES
(EXPRESSED OR IMPLIED). ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES,
INCLUDING (WITHOUT LIMITATION), ALL WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION
OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER.
In no event will ADTRAN or its suppliers be liable to Customer for any incidental, special, punitive,
exemplary or consequential damages experienced by either Customer or a third party (including, but not
limited to, loss of data or information, loss of profits, or loss of use). ADTRAN is not liable for damages
for any cause whatsoever (whether based in contract, tort, or otherwise) in excess of the amount paid for
the item. Some states do not allow the limitation or exclusion of liability for incidental or consequential
damages, so the above limitation or exclusion may not apply to Customer.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 8
Customer Service, Product Support Information, and Training
ADTRAN will repair and return this product if within ten years from the date of shipment the product does
not meet its published specification or the product fails while in service.
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the contact information given below.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CAPS)
department to have an RMA number issued. CAPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
CAPS Department
(256) 963-8722
Identify the RMA number clearly on the package (below address), and return to the following address:
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support web site provides a variety of support services such as a searchable knowledge
base, latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
http://support.adtran.com
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
Applications Engineering (800) 615-1176
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 9
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and troubleshooting tools. All of this, and more, is available at:
http://support.adtran.com
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Technical Support
(888) 4ADTRAN
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
http://www.adtran.com/aces
For questions, call the ACES Help Desk.
ACES Help Desk
(888) 874-ACES (2237)
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular products.
These courses include overviews on product features and functions while covering applications of
ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training
and courses taught at our facilities or at your site. For more information about training, please contact your
Territory Manager or the Enterprise Training Coordinator.
© 2002, ADTRAN, Inc.
Training Phone
(800) 615-1176, ext. 7500
Training Fax
(256) 963-6700
Training Email
training@adtran.com
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 10
TOTAL ACCESS 600 SERIES SHDSL IAD USER INTERFACE GUIDE
This document is designed for use by network administrators and others who will configure and provision the Total
AccessŠ 600 Series SHDSL Integrated Access Device (IAD). It contains overview information, information about
navigating the VT 100 user interface, configuration information, and menu descriptions.
CONTENTS
7RWDO$FFHVV2YHUYLHZ $QDORJ/LIHOLQH )LUPZDUH8SGDWHV 9RLFH2YHU'6/2YHUYLHZ 9RLFH2YHU$702YHUYLHZ 9RLFH2YHU'6/$SSOLFDWLRQ &RQILJXULQJWKH7RWDO$FFHVV 6\VWHP,QIR 6\VWHP1DPH 6\VWHP/RFDWLRQ 6\VWHP&RQWDFW 8QLW1DPH &/(,&RGH 3DUW1XPEHU 6HULDO1XPEHU )LUPZDUH5HYLVLRQ %RRWFRGH5HYLVLRQ 6\VWHP8SWLPH 'DWH7LPH 6\VWHP&RQILJ 1HWZRUN7LPLQJ0RGH 1HWZRUN 7HOQHW$FFHVV 7HOQHW8VHU/LVW 1DPH $XWKHQ0HWKRG 3DVVZRUG ,GOH7LPH /HYHO 0DLQW3RUW0HQX 3DVVZRUG3URWHFW 3DVVZRUG %DXG5DWH 'DWD%LWV 3DULW\ 6WRS%LWV 1HWZRUN7LPH 6HUYHU7\SH Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 11
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© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 12
$$/5HFHLYH)UDPHV $$/7UDQVPLW'LVFDUGHG)UDPHV $$/5HFHLYH(UURUV $$/5HFHLYH'LVFDUGHG)UDPHV $$/1R$70)UDPHV $$/1R'DWD3DFNHWV &OHDU6WDWV &RQILJXULQJWKH5RXWHU±&RQILJXUDWLRQ *OREDO ,3 0RGH 6WDWLF5RXWHV '+&36HUYHU 'RPDLQ1DPHV 8'35HOD\ 0RGH 8'35HOD\/LVW %ULGJH 0RGH $GGUHVV7DEOH 6HFXULW\ )LOWHU'HILQHV )LOWHU'HILQHV0$&)LOWHU'HILQHV )LOWHU'HILQHV3DWWHUQ)LOWHU'HILQHV )LOWHU'HILQHV,3)LOWHU'HILQHV (WKHUQHW ,3 ,3$GGUHVV 6XEQHW0DVN 'HIDXOW*DWHZD\ 5,3 3UR[\$53 0$&$GGUHVV :$1 /3URWRFRO $70 'HVFULSWLRQ 93, 9&, 3&53HDN&HOO5DWH 4264XDOLW\RI6HUYLFH 3URWRFRO 5)&,3 $FWLYH )DU(QG,3$GGUHVV ,3QHWPDVN /RFDO,3$GGUHVV 1$7 5,3 Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 13
5)&%ULGJH 333R$70 $XWKHQWLFDWLRQ 7;0HWKRG 7;8VHUQDPH 7;3DVVZRUG 5;8VHUQDPH 5;3DVVZRUG ,3 0RGH /RFDO,3 1HWPDVN 5HPRWH,3 1$7 5RXWH 5,3 333 9-&RPSUHVVLRQ 0D[&RQILJ 0D[7LPHU 0D[)DLOXUH (QFDSVXODWLRQ )LOWHUV :$172/$1,Q ,Q([FHSWLRQV /$172:$12XW 2XW([FHSWLRQV &RQILJXULQJWKH5RXWHU±6WDWXV 6HVVLRQ $53FDFKH %ULGJH7DEOH ,35RXWHV /$16WDWV ,36WDWV &RQILJXULQJWKH5RXWHU±/RJV 6\VORJ+RVW 333/RJ &RQQHFWLRQ/RJ 1HWZRUN/RJ $FWLYH :UDS /HYHO 9LHZ &OHDU &RQILJXULQJ9RLFH6XSSRUW±&RQILJ &DOO&RQWURO 93, 9&, &RQILJXULQJ9RLFH6XSSRUW±6WDWXV © 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 14
*DWHZD\6WDWV 39&6WDWV 32766WDWV &OHDU6WDWV 0DQDJLQJWKH0RGXOHV±0RGXOHV 1(76+'6/ 0HQX 'DWD5DWH )UDPH0RGH $QQH[$% ,78*VSDQ 7HVW 1HWZRUN/RRSEDFN 6HQG&KHFN 6HQG&KHFN$/7 6WDWXV 6LJQDO6WDWH 'DWD5DWH )UDPH0RGH *KV6WDWH *KV(YHQW );6 (&$'3&0 0DQDJLQJWKH0RGXOHV±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otal Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 15
$SSHQGL[(5)&4XLFN6WDUW,35RXWLQJ ,35RXWLQJ $SSHQGL[)5)&4XLFN6WDUW,35RXWLQJZLWK1$7 ,35RXWLQJZLWK1$7 $SSHQGL[*5)&4XLFN6WDUW%ULGJLQJ %ULGJLQJ $SSHQGL[+&UDIW3RUW&RQQHFWLRQ3LQRXW FIGURES
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
)LJXUH
7RWDO$FFHVV5HDU3DQHO 9RLFHRYHU'6/ 6\VWHP,QIRUPDWLRQ0HQX 6\VWHP&RQILJXUDWLRQ0HQX 6\VWHP8WLOLW\0HQX :$10HQX $70&RQILJ0HQX $706WDWV0HQX 5RXWHU&RQILJXUDWLRQ0HQX *OREDO0HQX (WKHUQHW0HQX :$10HQX 5RXWHU6WDWXV0HQX 5RXWHU/RJV0HQX 9RLFH&RQILJ0HQX 9RLFH6WDWXV0HQX 0RGXOHV0HQX 96HWXS0HQX 7RSOHYHO7HUPLQDO0HQX:LQGRZ $SSOLFDWLRQ'LDJUDP $SSOLFDWLRQ'LDJUDP © 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 16
1.
TOTAL ACCESS 600 OVERVIEW
The Total AccessŠ 600 is a complete solution Integrated Access Device (IAD) for Voice over ATM (VoATM) applications. The unit includes a modular network interface, Nx64 V.35 interface, 10/100BaseT interface, FXS ports, lifeline voice backup, and an optional battery back-up for added security. The Total Access 600 can provision, test, and
provide status for any of the voice and data interfaces. All connections are made via the rear panel. In addition to a
built-in IP router, the Total Access 600 contains an echo canceller and ADPCM compression modules necessary for
VoATM applications.
Analog Lifeline
The LIFE LINE connector on the rear panel (see Figure 1) provides assured voice for port 1. When a connection to the
Voice Gateway is not possible due to loss of power or some other reason, an on-board relay opens and the first port of
the voice connector is provided with analog voice from the analog lifeline connection.
For the analog lifeline feature to work, the user must subscribe to an analog voice line and it must
be connected via the lifeline connector.
Figure 1. Total Access 600 Rear Panel
Firmware Updates
Firmware can be updated by using XMODEM transfer protocol via the unit’s CRAFT port (see Figure 1) or by using
TFTP from a network server. (See Appendix A. Updating Total Access 600 Firmware using XMODEM on page 54
and Appendix B. Updating Total Access 600 Firmware using TFTP on page 57.)
The terminal menu is the access point to all other operations. Each terminal menu item has several functions and submenus that identify and provide access to specific operations and parameters. These menu selections are described later
in this User Interface Guide.
See Appendix C for instructions about navigating the terminal menus.
See Appendix H for the CRAFT port connection pin-out.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 17
2.
VOICE OVER DSL OVERVIEW
Voice over DSL (VoDSL) refers to providing toll quality voice access to the Public Switched Telephone Network
(PSTN) over twisted copper pair using DSL. Data can be combined with multiple voice lines over a single medium via
DSL, thus yielding many advantages over traditional TDM technologies.
Traditional TDM technologies are limited by statically allocating bandwidth. DSL overcomes this by providing a large
bandwidth and utilizing other technologies, such as ATM, to dynamically assign bandwidth as it is needed. Because
of this, the user is able to add voice and data connections over a DSL line with flexibility and ease.
3.
VOICE OVER ATM OVERVIEW
Voice over ATM is the technology used to transmit voice conversations over a data network using Asynchronous
Transfer Mode (ATM). There are several potential benefits to moving voice over a data network using ATM. First, the
small, fixed-length cells require lower processing overhead. Second, these small, fixed-length cells allow higher transmission speeds than traditional packet switching methods.
ATM allocates bandwidth on demand, making it suitable for high-speed connection of voice, data, and video services.
Conventional networks carry data in a synchronous manner. Because empty slots are circulating even when the link is
not needed, network capacity is wasted. ATM automatically adjusts the network capacity to meet the system needs.
4.
VOICE OVER DSL APPLICATION
The Total Access 600 connects to a DSLAM via DSL and ATM. The Total Access 600 has a built in echo canceller
that provides G.165 echo cancellation. The module can automatically detect ADPCM and enable it as needed.
Figure 2 shows a typical VoDSL application. The Total Access 600 connects to the ATM network, via a DSLAM, to
provide both voice and high speed data from a single platform.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 18
SCU
1181015L1
DS3MX
1181020L1
DS3MX
1181020L1
POWER
POWER
STATUS
STATUS
TEST
TEST
LOCKOUT
LOCKOUT
ON LINE
ON LINE
MODE
HD-10 BRI Mux
HD-10 BRI Mux
HD-10 BRI Mux
HD-10 BRI Mux
QFC-C QFC-C QFC-C QFC-C T1-OR T1-OR T1-OR T1-OR HTU-C
HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C
POWER
POWER
POWER
HTU-C HTU-C HTU-C HTU-C
POWER
PWR
PWR
PWR
PWR
1181200L1
1181200L1
1181200L1
1181200L1
DSX
DSX
DSX
DSX
LBK
LBK
LBK
LBK
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
DSX
#1
DSX
#1
DSX
#1
DSX
#1
5
5
5
5
DSX
#2
DSX
#2
DSX
#2
DSX
#2
6
6
6
6
DSX
#3
DSX
#3
DSX
#3
DSX
#3
7
7
7
7
DSX
#4
DSX
#4
DSX
#4
DSX
#4
SELECT
HST
ACO
FSE
ALM
ACO
C
R
A
APS
APS
TEST/
TEST/
ENABLE
ENABLE
F
T
8
9
8
9
8
9
1181300L1
10
10
DSL
DSL
1181310L1
1181300L1
1181310L1
1181310L1
1181310L1
1181101L1
PWR
DSX
LBK
TST
ALM
TX RX
+
TST
ALM
A
ACT
P
GRN = NORM
YEL = MAN
S
LINK
S
ACT
ALM
A
ACT
P
GRN = NORM
YEL = MAN
S
V.35 RX
GRN = NORM
YEL = MAN
–
R
X
6V
–
R
X
6V
–
X
6V
–
T
R
X
X
M
O
N
RX
M
O
N
RX
M
O
N
RX
TX
A ACT
A ACT
P
P
P
S
V.35 TX
DATA
S
GRN = NORM
YEL = MAN
S
VOICE
GRN = NORM
YEL = MAN
BATT
TX
M
O
N
RX
A ACT
P
S
GRN = NORM
YEL = MAN
TX
M
O
N
RX
A ACT
P
S
TST
LP1
LP1
LP2
LP2
ALM
TX
TX
E
Q
E
Q
RX
RX
TX
A
GRN = NORM
YEL = MAN
DSX
TST
E
Q
RX
1181101L1
PWR
DSX
ALM
TX
E
Q
RX
1181101L1
PWR
LP1
LP2
ALM
TX
E
Q
RX
1181101L1
TST
LP2
ALM
TX
E
Q
DSX
LP1
LP2
ALM
TX
RX
PWR
TST
LP1
LP2
1181101L1
DSX
TST
LP1
E
Q
PWR
DSX
TST
ALM
TX
RX
1181101L1
PWR
DSX
LP2
E
Q
RX
1181101L1
PWR
LP1
ALM
TX
E
Q
RX
1181101L1
TST
LP2
ALM
TX
E
Q
DSX
LP1
LP2
ALM
TX
RX
PWR
TST
LP1
LP2
1181101L1
DSX
TST
LP1
E
Q
PWR
DSX
TST
ALM
TX
RX
1181101L1
PWR
DSX
LP1
LP2
E
Q
RX
1181101L1
PWR
TST
ALM
TX
E
Q
RX
1181101L1
DSX
LP2
ALM
TX
E
Q
PWR
LP1
LP2
ALM
TX
RX
1181101L1
TST
LP1
LP2
ALM
+
R
DSX
TST
LP1
ALM
T
X
TX
PWR
DSX
TST
LP
+
T
X
TX
1181101L1
PWR
DSX
LBK
ALM
+
T
X
TX
M
O
N
TST
ALM
A
P
GRN = NORM
YEL = MAN
DSX
LP
ALM
PWR
6V
TST
ACT
PWR
LBK
LP
ALM
PWR
DSX
LBK
LP
9
10
DSL
1181300L1
DSX
8
10
DSL
1181300L1
PWR
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
TX
M
O
N
RX
M
O
N
RX
RX
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
PWR/NET
Figure 2. Voice over DSL
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 19
5.
CONFIGURING THE TOTAL ACCESS 600
System Info
The 6<67(0,1)2 menu provides basic information about the unit and contains data fields for editing information.
Figure 3 displays the submenus available when you select this menu item.
Figure 3. System Information Menu
>System Name
Provides a user-configurable text string for the name of the TA 600. This name can help you distinguish between different installations. You can enter up to 31 characters in this field, including spaces and special characters (such as an
underbar). This name will appear on the top line of all screens.
>System Location
Provides a user-configurable text string for the location of the TA 600. This field is to help you keep track of the actual
physical location of the unit. You can enter up to 31 characters in this field, including spaces and special characters
(such as an underbar).
>System Contact
Provides a user-configurable text string for a contact name. You can use this field to enter the name, phone number,
or email address of a person responsible for the TA 600 system. You can enter up to 31 characters in this field, including spaces and special characters (such as an underbar).
>Unit Name
Product-specific name for the product assembly.
>CLEI Code
CLEI code for the product assembly.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 20
>Part Number
ADTRAN part number for the product assembly.
>Serial Number
Serial number of the product assembly.
>Firmware Revision
Displays the current firmware revision level of the controller.
>Bootcode Revision
Displays the bootcode revision.
>System Uptime
Displays the length of time since the TA 600 system reboot.
>Date/Time
Displays the current date and time, including seconds. This field can be edited. Enter the time in 24-hour format (such
as 23:00:00 for 11:00 pm). Enter the date in mm-dd-yyyy format (for example, 10-30-1998).
Each time you reset the system, this value resets to 0 days, 0 hours, 0 min and 0 secs.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 21
System Config
Set up the Total Access 600 operational configuration from the 6<67(0&21),* menu. Figure 4 shows the items included in this menu.
Figure 4. System Configuration Menu
>Network Timing Mode
Selects the timing source for the entire system. Network is the only timing option available.
Network
The system’s clock is recovered from the network (WAN interface).
>Telnet Access
Sets Telnet access to 21 or 2)).
>Telnet User List
Up to four users can be configured for access to the Total Access 600. Each user can be assigned a security level and
time out.
Name
A text string of the user name for this session.
Authen Method
The user can be authenticated in two ways:
PASSWORD
The Password field is used to authenticate the user.
RADIUS
The Radius client is used for authenticating the user.
Password
When the authenticating method is 3$66:25', this text string is used for the password.
Idle Time (1-255)
This sets the amount of time you can be idle before you are automatically logged off.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 22
Level
This is the security level granted to the user.
>Maint Port Menu
The Total Access 600’s VT 100 &5$)7 port can be accessed via an RJ-48 located on the rear panel. The setup for
these ports is under this menu.
Password Protect
When set to 12, the maintenance port is not password protected. When <(6 (def), the Total Access 600 will
prompt for a password upon startup.
Password
This is the text string that is used for comparison when password protecting the maintenance port. By
default, no password is entered.
If you forget your password, type CHALLENGE in all capital letters. Call technical support and
have the displayed CHALLENGE code ready.
The security level for the maintenance port is always set to 0. This gives full access to all menus.
Passwords are case-sensitive.
Instructions for Changing Passwords
Step
Action
1
Select the PASSWORD field—a new PASSWORD field displays.
2
Type the new password in the ENTER field.
3
Type the new password again in the CONFIRM field.
The password can contain up to 12 alphanumeric characters. You
can also use spaces and special characters in the password.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 23
Baud Rate
This is the asynchronous rate that the maintenance port will run. The possible values are 300, 1200, 2400,
4800, 9600 (def), 19200, 38400, 57600, and 115200.
Data Bits
This is the asynchronous bit rate that the maintenance port will run. The possible values are 7 or 8 (def) bits.
Parity
This is the asynchronous parity that the maintenance port will run. The possible values are 121((def), 2'',
or (9(1.
Stop Bits
This is the stop bit used for the maintenance port. The possible values are 1 (def), 1.5 or 2.
>Network Time
The Total Access 600 unit time can be entered manually from the6<67(0,1)2 menu, or the unit can receive time
from an NTP/SNTP server. The 1(7:25.7,0( menu includes all parameters relating to how the unit communicates
with the time server.
Server Type
The server type defines which port the Total Access 600 will listen on to receive timing information from the
time server.
NT Time
The Total Access 600 will receive time from an NT server running SNTP software on its TIME port.
SNTP
The Total Access 600 will receive time directly from an SNTP server.
Active
This network timing feature can be turned on and off. It determines whether the unit will request and receive
time from a time server.
Time Zone
There are several time zones available for the time to be displayed in. All time zones are based off of Greenwich Mean Time (GMT).
Adjust for Daylight Saving
Since some areas of the world use Daylight Savings Time, the Total Access 600 is designed to adjust the
time on the first Sunday in April and the last Sunday in October accordingly if this option is turned on.
Host Address
This is the IP address of the time server that the Total Access 600 will request and receive time from.
Refresh
This is the interval of time between each request the Total Access 600 sends out to the time server. A smaller
refresh time guarantees that the unit receives the correct time from the server and corrects possible errors
more quickly, but it is more taxing on the machine. A range of refresh times is available for the user to
decide which is best for their unit.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 24
Status
This displays the current status of the time negotiation process. If an error is displayed, check all connections
and configurations to try to resolve the problem.
System Utility
Use the 6<67(087,/,7< menu to view and set the system parameters shown in Figure 5.
Figure 5. System Utility Menu
>Upgrade Firmware
Updates firmware when TA 600 enhancements are released. Two transfer methods are available for use in updating
the Total Access 600 system controller.
Transfer Method
The two methods for upgrading are ;02'(0and7)73 (See Appendix A. Updating Total Access 600
Firmware using XMODEM on page 54 and Appendix B. Updating Total Access 600 Firmware using TFTP
on page 57 for more information.) 7)73 requires a TFTP server running somewhere on the network. The
Total Access 600 starts a TFTP client function which gets the upgrade code from the TFTP server. Selecting
;02'(0will load the upgrade code through the&5$)7 port using any PC terminal emulator with xmodem capability.
TFTP Server Address
This is required when the transfer method is TFTP. It is the IP address or domain name (if DNS is configured) of the TFTP server.
TFTP Server Filename
This is required when the transfer method is TFTP. It is the case-sensitive file name which contains the
upgrade code.
Transfer Status
This appears when TFTP is used. It displays the status of the transfer as it happens. Any error or success
message will be displayed here.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 25
Start Transfer
This activator is used when the configurable items in this menu are complete.
Before using 67$5775$16)(5, the TA 600 should have a valid IP address, subnet mask, and default
gateway (if required).
Abort Transfer
Use this activator to cancel any TFTP transfer in progress.
>Config Transfer
Sends a file containing the TA 600 configuration to a PC connected to the &5$)7port using XMODEM protocol or
to a file on a TFTP server using the TFTP protocol. See Appendix A. Updating Total Access 600 Firmware using
XMODEM on page 54 and Appendix B. Updating Total Access 600 Firmware using TFTP on page 57 for details.
&21),*75$16)(5 also lets you save the TA 600 configuration as a backup file, so you can use the same configuration
with multiple TA 600 units. In addition, &21),*75$16)(5 can retrieve a configuration file from a TFTP server.
To support these transfers, ADTRAN delivers a TFTP program with the TA 600 called TFTP Server. You can configure any PC running Microsoft Windows with this software, and store a configuration file.
Before using &21),*75$16)(5, the TA 600 should have a valid IP address, subnet mask, and
default gateway (if required).
Only one configuration transfer session (upload or download) can be active at a time.
Transfer Method
Displays the method used to transfer the configuration file to or from a server. XMODEM and TFTP are
supported.
Transfer Type
Only %,1$5< transfers are currently supported.
TFTP Server IP Address
Specifies the IP address of the TFTP server. Get this number from your system administrator.
TFTP Server Filename
Defines the name of the configuration file that you transfer to or retrieve from the TFTP server. The default
name is WDFIJ, but you can edit this name.
Current Transfer Status
Indicates the current status of the update.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 26
Previous Transfer Status
Indicates the status of the previous update.
Load and Use Config
Retrieves the configuration file specified in the 7)736(59(5),/(1$0( field from the server. To start this
command, enter < to begin or enter 1 to cancel.
If you execute this command, the TA 600 retrieves the configuration file, reboots, then restarts using the
new configuration.
Save Config Remotely
Saves the configuration file specified in 7)736(59(5),/(1$0( to the server identified in 7)73
6(59(5,3$''5(66. To start this command, enter < to begin or enter 1 to cancel.
Before using this command, you must have identified a valid TFTP server in 7)736(59(5,3
$''5(66.
>Ping
Allows you to send pings (ICMP requests) to hosts. The following items are under this menu:
Only one ping session can be active at a time.
Start/Stop
Activator to start and cancel a ping test.
Host Address
IP address or domain name (if DNS is configured) of device to receive the ping.
Size (40-1500)
Total size of the ping to send. Range is 40 to 1500 bytes. 64 is default.
# of Packets
Total packets to send every 2 seconds. Setting this to allows the client to ping continuously.
# Transmits
Total packets sent (read only).
# Receives
Total packets received (read only).
%Loss
Percentage loss based on ping returned from host (read only).
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 27
Configuring WAN Settings
>DSLAM Type
Set this to the type of DSLAM the Total Access 600 will be connecting to.
>Layer One Interface
This is the physical layer protocol used to connect the DSLAM to the Total Access 600.
>Layer Two Protocol
This is the data link layer protocol used to connect the DSLAM to the Total Access 600.
>ATM Config
Use the :$1 menu (Figure 6) to access the $70&21),* menu.
Figure 6. WAN Menu
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 28
Use the $70&21),* menu (Figure 7) to set the parameters listed below the figure.
Figure 7. ATM Config Menu
Idle Cells
The ,'/(&(//6 format must be configured for either $70)2580 or ,78. Configuring this setting incorrectly for a particular circuit will cause poor performance at the ATM layer.
This setting must match the configuration setting of the ATM switch or DSLAM at the other end of
the circuit.
Data Scrambling
'$7$6&5$0%/,1* can be (1$%/(' or ',6$%/(' for cell traffic. Configuring this setting incorrectly for a
particular circuit will cause poor performance.
This setting must match the configuration setting of the ATM switch or DSLAM at the other end of
the circuit.
>ATM Stats
Use the :$1 menu (Figure 6 on page 27) to access the $7067$76 menu (Figure 8) and view the parameters listed
below the figure.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 29
Figure 8. ATM Stats Menu
AP: Tx Cells
This is the number of cells transmitted.
AP: Rx Cells
This is the number of cells received.
AP: Rx OAM Cells
This is the number of OAM cells received
AP: Receive Cells Discarded
This is the number of cells received and discarded. An incrementing count in this field could indicate a configuration problem with the ATM layer.
AP: Receive Cell Errors
This is the number of cells received with an HEC error.
AP: Sync
This indicates cell delineation at the ATM layer.
AP: Out Of Cell Delineation
This indicates loss of cell delineation at the ATM layer.
AAL5: Transmit Frames
This is the number of AAL5 frames transmitted.
AAL5: Receive Frames
This is the number of AAL5 frames received.
AAL5: Transmit Discarded Frames
This is the number of AAL5 frames discarded.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 30
AAL5: Receive Errors
This is the number of AAL5 errors received.
AAL5: Receive Discarded Frames
This is the number of AAL5 frames discarded.
AAL5: No ATM Frames
This is for internal use only.
AAL5: No Data Packets
This is for internal use only.
Clear Stats
This is used to clear the counters on this menu screen.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 31
Configuring the Router – Configuration
Use the 5287(5&21),*85$7,21 menu (Figure 9) to access the */2%$/, (7+(51(7, and :$1 menus.
Figure 9. Router/Configuration Menu
>Global
Use the */2%$/ menu (Figure 10) to set up general router functions.
Figure 10. Global Menu
IP
This is used for general IP configuration.
Mode
This item controls how the Total Access 600 handles IP routes. When this option is set to 21(def), the
Total Access 600 will advertise and listen to routes from other IP routers. If 2)), the route table is still
used, but only static routes are used for routing IP packets and only the Ethernet port is used. IP packets
can be sent over the WAN, but only when bridged.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 32
Static Routes
Use this menu to enter static routes to other networks.
ACTIVE
Adds this static route entry to the IP routing table
when set to <(6 and removes it (if it was previously
added) if set to 12(def).
IP ADDRESS
The IP address of the host or network address of the
device being routed to.
SUBNET MASK
Determines the bits in the previous IP address that
are used. If this is to be a host route, it must be set to
all ones (255.255.255.255).
GATEWAY
The IP address of the router to receive the forwarded
IP packet.
HOPS
The number of router hops required to get to the network or host. Maximum distance is 15 hops.
PRIVATE
When set to 12, the Total Access 600 will advertise
this static route using RIP. Setting to <(6 means that
the route is kept private.
DHCP Server
DHCP MODE
When set to 21, the Total Access 600 acts as a
DHCP server and will dynamically assign IP, network mask, default gateway, and DNS addresses to
any device which transmits a broadcast DHCP request. The addresses assigned are based on the Total
Access 600’s own IP address and will be within the
same network.
DHCP RENEWAL TIME The number of hours that the DHCP server should
allow the device before it is required to send a new
DHCP request. The default is 15 hours, and 0 represents an infinite lease.
Domain Names
Enter the Total Access 600's domain name and the primary and secondary DNS servers in this menu.
DOMAIN NAME
Text string used to represent the domain name
used by the Total Access 600.
PRIMARY DNS
First server to which domain name requests are
sent.
SECONDARY DNS
Server used as a backup, in case the primary address does not respond to the request.
PRIMARY NBNS/WINS
Server to which NT domain name requests are
sent.
SECONDARY NBNS/WINS
Server used when there is no response from the
primary server.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 33
UDP Relay
This menu configures the Total Access 600 to act as a UDP relay agent for applications requiring a
response from UDP hosts that are not on the same network segment as their clients.
Mode
When this option is set to ON, the Total Access 600 will act as a relay agent.
UDP Relay List
Up to four relay destination servers can be specified in this list.
RELAY ADDRESS
This is the IP address of the server that will receive the relay packet.
UDP PORT TYPE
STANDARD (def)
The following standard UDP protocols are
relayed when set: DHCP, TFTP, DNS, NTP
(Network Time Protocol, port 123, NBNS
(NetBios Name Server, port 137), NBDG
(NetBIOS Datagram, port 138), and BootP.
SPECIFIED
When set, the UDP port (1 to 65535) can be
specified in the UDP Port columns (up to
three per server).
UDP PORT 1, 2, 3
Used for specifying UDP ports to be relayed.
These fields only apply when UDP PORT TYPE is
set to SPECIFIED.
Bridge
The %5,'*( menu is used to set up the bridge parameters for the Total Access 600. The bridging function
runs at the Media Access Control (MAC) level which allows any protocol packets that run over Ethernet to
be forwarded. Bridging can run concurrently with IP. However, when IP routing is active, IP packets (which
include ARP packets) are not bridged.
Mode
This is used to enable the bridge function.
Address Table
The Total Access 600 automatically maintains a table of MAC addresses detected and associates those
addresses with the LAN or WAN port from which they were received.
© 2002, ADTRAN, Inc.
AGING
The maximum time an idle MAC address remains in
the table before being removed. The value is in minutes.
FORWARD POLICY
When this parameter is set to 81.12:1 (def), any
bridge packet with a destination MAC address that
is not in the bridge table is forwarded to all other
ports. When set to .12:1, the packet with the unknown destination MAC address is dropped and is
not forwarded.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 34
Security
Filter Defines
The Total Access 600 can filter packets based on certain parameters within the packet. The method used
by the Total Access 600 allows the highest flexibility for defining filters and assigning them to a PVC.
The filters are set up in two steps: (1) defining the packet types, and (2) adding them to a list under the
PVC. This menu is used to define the individual filter defines based on packet type.
Filter Defines /MAC Filter Defines
The MAC filter is applied to bridge packets only. Bridge packets which are forwarded by the bridge
functionality of the Total Access 600 are defined here. Up to 32 MAC defines can be specified.
NAME
SRC ADDR
SRC MASK
DEST ADDR
DEST MASK
MAC TYPE
TYPE MSK
Identifies the filter entry.
48-bit MAC source address used for
comparison. (hexadecimal format)
Bits in the MAC source address which are
compared. (hexadecimal format)
48-bit MAC destination address used for
comparison. (hexadecimal format)
Bits in the MAC destination address used for
comparison. (hexadecimal format)
16-bit MAC type field used for comparison.
(hexadecimal format)
Bits in the MAC type field used for comparison.
(hexadecimal format)
Filter Defines /Pattern Filter Defines
The pattern filter is applied to bridge packets only. That is any packet which is forwarded by the bridge
functionality of the Total Access 600. Up to 32 pattern defines can be specified.
NAME
Identifies the filter entry.
OFFSET
Offset from beginning of packet of where to
start the pattern comparison.
PATTERN
64 bits used for comparison. (hexadecimal
format)
MASK
Bits in the pattern to be compared.
(hexadecimal format)
Filter Defines /IP Filter Defines
The IP filter defines apply to any IP packet, whether it is routed or bridged. Up to 32 IP defines can be
specified.
NAME
Identifies the filter entry.
IP SRC
IP address compared to the source address.
(dotted decimal format)
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 35
65&0$6.
Bits which are used in the source comparison.
(dotted decimal format)
,3'(67
IP address compared to the destination address.
(dotted decimal format)
'(670$6.
Bits which are used in the destination
comparison. (dotted decimal format)
65&3257
IP source port number used for comparison
Range: 0 to 65535. (decimal format)
65&3257
&035
Type of comparison that is performed.
= means ports equal to
not = means port not equal to
> means port greater than
< means port less than
None - means the source port is not compared
'673257
IP destination port number used for comparison
Range: 0 to 65535. (decimal format)
'673257
&035
Type of comparison that is performed
= means ports equal to
not = means port not equal to
> means port greater than
< means port less than
None - means the destination port is not
compared
35272
Protocol used for comparison. Range: 0 to 255.
(decimal format)
35272&035
Type of comparison that is performed
= means protocols equal to
not = means protocols not equal to
> means protocols greater than
< means protocols less than
None means the protocol is not compared
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 36
7&3(67
Yes - only when TCP established
No - only when TCP not established
Ignore - ignore TCP flags
>Ethernet
Use the (7+(51(7 menu (Figure 11) to configure the Ethernet port on the Total Access 600.
Figure 11. Ethernet Menu
IP
This is used to set up the IP addresses for the LAN on the Total Access 600.
IP Address
The IP address assigned to the Total Access 600's Ethernet port is set here. This address must be unique
within the network.
Subnet Mask
This is the IP network mask that is to be applied to the Total Access 600's Ethernet port.
Default Gateway
The default gateway is used by the Total Access 600 to send IP packets whose destination address is not
found in the route table.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 37
RIP
Use this menu to enable RIP on the LAN interface.
MODE
Enables or disables RIP.
PROTOCOL
Specifies the RIP protocol. Choices are V1 (def)
(which is RIP version 1) or V2 (RIP version 2).
METHOD
Specifies the way the RIP protocol sends out its
advertisements. Choices are given below.
NONE
All routes in the router table are advertised
with no modification of the metrics.
SPLIT HORIZON
Only routes not learned from this circuit are
advertised.
POISON REVERSE GHI
All routes are advertised, but the routes
learned from this port are “poisoned” with an
infinite metric.
DIRECTION
Allows the direction at which RIP advertisements are sent and listened to be specified.
TX AND RX GHI
RIP advertisements are periodically
transmitted and are listened to on this port.
TX ONLY
RIP advertisements are periodically
transmitted but are not listened to on this
port.
RX ONLY
RIP advertisements are not transmitted on
this port, but are listened.
V2 SECRET
Enter the secret used by RIP version 2 here.
Proxy ARP
This feature allows the network portion of a group of addresses to be shared among several physical
network segments. The ARP protocol provides a way for devices to create a mapping between physical
addresses and logical IP addresses. Proxy ARP makes use of this mapping feature by instructing a
router to answer ARP requests as a "proxy" for the IP addresses behind one of its ports. The device
which sent the ARP request will then correctly assume that it can reach the requested IP address by
sending packets to the physical address that was returned. This technique effectively hides the fact that
a network has been (further) subnetted. If this option is set to <(6, when an ARP request is received on
the Ethernet port the address is looked up in the IP routing table. If the forwarding port is not on the
Ethernet port and the route is not the default route, the Total Access 600 will answer the request with its
own hardware address.
MAC Address
This is a read-only MAC address programmed at ADTRAN.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 38
>WAN
Use the :$1 menu (Figure 12) to configure WAN settings on the Total Access 600.
Figure 12. WAN Menu
L2 Protocol
Displays the current L2 protocol - ATM (Read Only).
ATM
Use the ATM menu to setup Data PVCs for the router.
Description
This is the text description for the PVC.
VPI
ATM virtual port identifier.
VCI
This is the ATM virtual channel identifier.
PCR (Peak Cell Rate)
Limits transmitted cells.
QOS (Quality of Service)
Indicates this PVC’s traffic class.
Protocol
This is the protocol supported on the PVC.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 39
RFC1483 IP
Use this selection to support IP on this PVC. (These settings only take effect when RFC1483 is the
selected protocol.)
Active
This selection enables IP on this PVC.
Far - End IP Address
This is the address of the NEXT hop router on this interface.
IP netmask
This is the network mask used for this interface.
Local IP Address
This is the IP address for this PVC.
NAT
Use this menu to set up and use Network Address Translation on this interface.
NETWORK ADDRESS
PORT TRANSLATION
PUBLIC IP ADDRESS
MODE
TRANSLATION TABLE
PUBLIC ADDRESS
MODE
PROTOCOL
PUBLIC PORT MODE
© 2002, ADTRAN, Inc.
By enabling port translation, IP packets are modified
as they pass through this interface. During transmission, private addresses are translated into a single
public (NAPT) IP address. Incoming packets are
translated from the public to private address based on
the protocol port numbers. Once enabled, you must
set up NAT for use.
The port translation requires at least a single real IP
address for translating. This value can use the IP assigned to the interface (or assigned via layer 2 protocol like PPP), obtained using DHCP client, or
statically specified on this menu. If the address cannot
be learned, then it must be specified in order for the
translation to work.
Add translation entries to "fine tune" special protocols or specify private addresses.
The public IP address used for this translation
entry can be the NAPT IP address assigned to the
link or can be specified. You specify an address to
direct packets with certain protocols to different
servers.
The upper layer protocol that is to be monitored
for translation. For TCP and UDP, a port number
must also be specified.
The public destination port associated with this
entry can be specified to add more control over
certain types of traffic. The default, $1<3257,
covers all port types.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 40
PRIVATE ADDRESS
MODE
PRIVATE PORT
MODE
TRANSLATE BODY
NAT VIEW
NAPT ADDRESS
ENTRY COUNT
ENTRY OVERFLOW
COUNT
The private IP address can be specified to steer
certain protocols and ports to specific servers in
the private network. Likewise, internal hosts can
be steered to certain servers on the public
network. A new request from the public network
matching this entry’s public parameters will be
dropped if this mode is set to $1<,17(51$/.
The private destination port associated with this
entry can be specified to add more control over
certain types of traffic. Leave as $1<3257 to
cover all port types.
By default, the application payload in the packet
is scanned for occurrences of the private/public IP
address in binary or ASCII form. Set this to 1R for
applications where this will cause problems.
Shows the protocols that are actively being translated.
Represents the public address that is being used as the
NAPT address.
The number of entries in the NAT table.
A count of the dropped entries due to low memory.
RIP
Use this menu to enable RIP on the WAN interface. (See RIP on page 37 for description of options.)
RFC 1483 Bridge
This is used to enable bridge mode on this PVC. (These settings only take effect when RFC 1483 is the
selected protocol.)
PPPoATM
The Total Access 600 uses the PPPoATM profile to specify the profile used when connected using PPP.
Authentication
The authentication menu contains the required parameters for the authentication of the PPP peer and for
being authenticated by the PPP peer. Authentication is applied between the Total Access 600 and the
PPP peer as follows:
TX Method
This parameter specifies how the Total Access 600 is to be authenticated by the PPP peer. There are four
possible selections.
NONE (def)
The connection will not allow the PPP peer to authenticate it.
PAP, CHAP, OR EAP
The connection can be authenticated using PAP,
CHAP or EAP.
CHAP OR EAP
The connection can be authenticated using CHAP or
EAP only.
EAP
The connection will only allow authentication by the
peer using EAP.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 41
TX Username
This is the username that is used when being authenticated by the PPP peer.
TX Password
This is the password or secret that is used when being authenticated by the PPP peer.
RX Username
This is the username used to authenticate the PPP peer.
RX Password
This is the password or secret that is used to authenticate the PPP peer.
IP
The IP menu contains the parameters for exchanging IP data with the PPP peer.
Mode
Setting to ON (def) will permit this connection profile to negotiate PPP IPCP with the PPP peer for
exchanging of IP packets.
Local IP
This is the IP address that is assigned to the PPP link when using numbered links. Leaving this as
0.0.0.0 means the Total Access 600 will determine its IP address using PPP IPCP. If the far end router
does not assign an IP address, the PPP link is left unnumbered.
Netmask
This network mask is applied to the IP/Local IP address for determining the PPP peer's network. If left
as 0.0.0.0, a standard network mask is used.
Remote IP
The PPP peer's IP address or network can be set here, if known. Leaving this at 0.0.0.0 means that the
Total Access 600 will determine the PPP peer's IP and network using the PPP IPCP.
NAT
The Total Access 600 can perform Network Address Translation. This feature is most widely used when
connecting to the Internet. The Ethernet network can consist of private network numbers. When this
profile is connected, all IP addresses on the Ethernet side are translated into the one real IP address
negotiated with the PPP peer (ISP). Multiple stations on the Ethernet side can access the Internet simultaneously. Setting this option to ON will cause the Total Access 600 to perform NAT. In the OFF (def)
position, the unit will route across the connection normally.
Route
The IP parameters are configured in this menu. Usually the Total Access 600 will automatically discover the PPP peer's networks using PPP IPCP and/or RIP.
• Route/Static Route
Selecting yes will add a static route to the remote peer to the route table.
• Route/Private
Selecting yes will prevent this route from being advertised.
• Route/Hops (1-16)
This value is the metric or number of hops that RIP will use in advertising the static route. The range is
1 to 16, where 1 is the default. The value 16 is considered an infinite distance (poisoned route).
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 42
• Route/Force IP
When set to YES, the Total Access 600 will force the PPP peer to use the IP address in the LOCAL IP for
this profile as its WAN IP address. Normally this is set in the NO (def) position.
RIP
The RIP parameters can be adjusted from their defaults under this menu.
• Mode
The Total Access 600 performs RIP over the WAN connection when this is set to ON (def).
• Protocol
The Total Access 600 performs version 1, V1 (def), or version 2, V2, of RIP on this WAN connection.
• Method
SPLIT HORIZON
Only routes not learned on the WAN connection
are advertised.
POISON REVERSE
All routes are advertised, including routes learned
from the WAN connection. These routes are poisoned.
NONE
All routes are advertised, including routes learned
from the WAN connection. No attempt is made to
poison these routes.
GHI
• Direction
TX AND RXGHI
RIP advertisements are transmitted and listened to
on the WAN connection.
TX ONLY
RIP advertisements are transmitted and not listened
to.
RX ONLY
RIP advertisements are listened to but not transmitted.
• Triggered
When set to YES, only IP RIP updates are sent when the routing table has changed and learned routes are
not "aged." When set to NO (def), updates are sent periodically.
• Retain
When this Connection List entry is disconnected and this parameter is set to YES, all routes learned from
this WAN connection are retained and their routing interface is set to idle.
PPP
The Total Access 600 supports the IETF standards for the Point-to-Point Protocol. The PPP state
machine running in the Total Access 600 can be fine-tuned to support many applications that can be
employed. The configurable items under this menu can be changed from their default values for special
cases.
VJ Compression
When this item is set to ON, the Total Access 600 will perform TCP/IP header compression known as
Van Jacobson compression to the PPP peer.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 43
Max Config
This value is the number of unanswered configuration-requests that should be transmitted before giving
up on a call. The possible values are 5, 10 (def), 15 and 20.
Max Timer
This value is the number of seconds to wait between unanswered configuration requests. The possible
values are 1 sec, 2 secs (def), 3 secs, 5 secs and 10 secs.
Max Failure
Due to the nature of PPP, configuration options may not be agreed upon between two PPP peers. This
value is the number of configuration-naks that should occur before an option is configuration-rejected.
This allows a connection to succeed that might otherwise fail. The possible values are 5 (def), 10, 15
and 20.
Encapsulation
This is the PPP encapsulation. (LLC or VC-Mux)
Filters
The Total Access 600 can block packets in and out of a WAN port by use of the filters. They are set up
in two steps: 1) define the types of packets that would be of interest in the CONFIGURATION/GLOBAL/
SECURITY/FILTER DEFINES menu, and 2) set up the filter type and combination of defines that will cause a
packet block.
WAN-TO-LAN (In)
The packets which come into the Total Access 600 can be filtered in three ways:
DISABLED (GHI
Turns off packet input filtering. No incoming packets
are blocked.
BLOCK ALL
All incoming packets from the WAN are blocked except as defined in the FILTERS/IN EXCEPTIONS list.
FORWARD ALL
All incoming packets from the WAN are not blocked
except as defined in the FILTERS/IN EXCEPTIONS list.
In Exceptions
This is a list of up to 32 filter entries which can be combined using the operations field. The operations
are performed in the order they appear on the list.
© 2002, ADTRAN, Inc.
ACTIVE
Turns this entry active when set to ON
TYPE
Selects the filter define list to reference:
MAC
from the CONFIGURATION/GLOBAL/SECURITY/FILTER
DEFINES/MAC FILTER DEFINES list.
PATTERN
from the CONFIGURATION/GLOBAL/SECURITY/FILTER
DEFINES/PATTERN FILTER DEFINES list.
,3
from the CONFIGURATION/GLOBAL/SECURITY/FILTER
DEFINES/IP FILTER DEFINES list.
,3;
from theCONFIGURATION/GLOBAL/SECURITY/FILTER
DEFINES/IPX FILTER DEFINES list.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 44
FILTER LIST NAME
Selects between filters defined in the list.
NEXT OPER
The next operation to use to combine with the next
filter in the list:
(1'
the last filter to combination.
$1'
logically AND this filter with the next filter in the
list.
25
logically OR this filter with the next filter in the list.
LAN-TO-WAN (Out)
The packets which come out toward the WAN from the TA600 can be filtered in three ways:
DISABLED (GHI
Turns off packet input filtering. No outgoing packets
are blocked.
BLOCK ALL
All outgoing packets to the WAN are blocked except as
defined in the FILTERS/OUT EXCEPTIONS list.
FORWARD ALL
All outgoing packets to the WAN are not blocked except as defined in the FILTERS/OUT EXCEPTIONS list.
Out Exceptions
This is a list of up to 32 filter entries. The setup is exactly the same as the ),/7(56,1(;&(37,216 list.
Configuring the Router – Status
Use the 5287(567$786menu to view and set the parameters shown in Figure 13. The 5287(567$786
screens give the user useful information for debugging the current routes in the Total Access 600.
Figure 13. Router/Status Menu
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 45
>Session
This menu maintains statistics about the active ATM PVCs.
>ARP cache
This is a listing of the currently connected Ethernet port on the LAN.
>Bridge Table
This shows the detected MAC addresses and the interface to which they are associated.
>IP Routes
This shows the current routes in the Total Access 600 and their use.
>LAN Stats
This shows traffic over the LAN interface.
>IP Stats
This shows IP traffic through the Total Access 600.
Configuring the Router – Logs
The Logs menu (Figure 14) contains logs displaying important information about the running condition of the Total
Access 600. The logs can be set to capture diagnostics of error conditions only by way of a log level. The levels are
divided up as follows:
level 0 - Fatal event (causes reset)
level 1 - Critical event
level 2 - Error event
level 3 - Warning event
level 4 - Notify event
level 5 - Informational event
level 6 - Debugging event
Figure 14. Router/Logs Menu
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 46
Sys log Host
Set this to the IP address or domain name (if DNS configured) of the sys log host device. All log events are sent to this
device.
PPP Log
Information pertaining to the PPP negotiation and authentication is logged in the PPP log.
Connection Log
Information pertaining to the call placement and answering is logged in the Connection log.
Network Log
Information pertaining to routing protocols is placed in this log.
Each log (PPP log, Connection log, and Network log) contains the following elements.
Active
When set to <(6 (def), PPP events below or equal the log level are logged into the log.
Wrap
When set to <(6 (def), new PPP events will overwrite old PPP events when the log is full. All logging
will stop when the log is full and set to 12.
Level
In order to log events, they must be at or below this level. Range is 0 to 6. The default is 3.
View
This menu displays the log list. The fields are as follows:
DATE/TIME
Date and time event occurred.
LEVEL
Level associated with this event (0-6).
MESSAGE
Text message for this event. If message is too
long to fit on the line, another event appears
below it continuing the message.
Clear
This clears the log when activated.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 47
Configuring Voice Support – Config
Use the 92,&(&21),* menu to view and set the parameters shown in Figure 15.
Figure 15. Voice/Config Menu
>Call Control
The &$//&21752/ setting is used to configure the correct Voice Gateway protocol for voice signaling control between the Total Access 600 and the configured Gateway. The &$//&21752/ setting must be configured correctly
before the voice circuits will work correctly. The Total Access 600 supports Jetstream, Tollbridge, and CopperCom
Voice Gateways.
>VPI
The 93, setting is used to configure the Total Access 600 virtual path setting used to communicate with the configured
Voice Gateway.
>VCI
The 9&, setting is used to configure the Total Access 600 virtual circuit setting used to communicate with the configured Voice Gateway.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 48
Configuring Voice Support – Status
Use the 92,&(67$786menu to view and set the parameters shown in Figure 16.
Figure 16. Voice/Status Menu
>Gateway Stats
The *$7(:$<67$76 menu shows the current state of the communication link between the Total Access 600 and the
Voice Gateway. The Gateway Link is indicated as 83 or '2:1. A count of management messages is indicated along
with the number of active calls in progress.
>PVC Stats
The 39&67$76 menu shows the current state of the virtual circuit used between the Voice Gateway and the Total
Access 600 IAD for voice signaling and voice payload delivery.
>POTS Stats
The 327667$76 menu shows real-time indication status of each voice port on the Total Access 600. From this menu,
on a per port basis, the user can determine which ports are active/inactive. Several statistics at this menu are used only
for internal ADTRAN development. Task, Inserts, and Drops indicators are for internal use only.
>Clear Stats
The &/($567$76 menu can be used to clear the counters used for Voice Status menus.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 49
Managing the Modules – Modules
Use the 02'8/(6menu to view and set the parameters shown in Figure 17. The Total Access 600 contains four fixed
modules: The WAN/Network interface, FXS, Echo Canceller/ADPCM module, and the V.35 interface. The 02'
8/(6 table allows management of the on-board modules in the Total Access 600.
This menu contains 0(18, $/$50, 7(67, and 67$786 indicators/menus customized for each module.
Figure 17. Modules Menu
>NET (SHDSL)
Menu
Data Rate
Used to select data rate of the network connection. (This should match the DSLAM settings.)
Frame Mode
Used to select either SDSL Framed (def) or SDSL Framed Plesiosynchronous with bit stuffing. (This
should match the DSLAM settings.)
Annex A/B
Used to select $11(;$$11(;% or both.
ITU-991.2/Gspan
Chooses between ,787 or */2%(63$19.
Test
These tests are meant for debug purposes only. A reboot may be required to return the Total Access 600 to
normal operation.
Network Loopback
Sets the network interface in loopback mode.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 50
Send/Check 2047
Sends and checks a 2047 BERT pattern over the network interface (assuming LTU in loopback). Results
of the test can be found in Test Results.
Send/Check ALT
Sends and checks an alternating pattern over the network interface (assuming LTU in loopback). Results
of the test can be found in Test Results.
Status
Signal State
Internal ADTRAN use.
Data Rate
Rate at which the WAN has connected.
Frame Mode
Framing mode.
G.hs State
Internal ADTRAN use.
G.hs Event
Internal ADTRAN use.
>FXS
Refer to the Total Access 600 Series FXS Voice Ports User Interface Guide.
>EC/ADPCM
Refer to the Total Access 600 Series FXS Voice Ports User Interface Guide.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 51
Managing the Modules – V.35 Setup
Use the 96(783menu to view and set the parameters shown in Figure 18.
Figure 18. V.35 Setup Menu
&+$11(/5$7( and (,$ settings are supported via this menu option. For all typical applications, these settings are
left in their default states.
>ATM/FR IWF
This menu contains the setup and status for the ATM/Frame Relay interworking functions.
Mode
The 02'( setting configures the V.35 port for FRF5 or FRF8 operation, depending upon the application
being supported.
FRF5
This is also known as Network Interworking. Use this mode for Frame Relay over ATM.
FRF8
This is also known as Service Interworking. In this mode, the Total Access 600 performs a translation
between Frame Relay and ATM protocols.
Configuration
The &21),*85$7,21 menu is used to support the configuration of Frame-to-ATM interworking, signaling
formats, timeout values, and PVC settings.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 52
The following settings are used for FRF5.
LAN FR MAINT PROTOCOL
Frame Relay maintenance or signaling protocol
between local V.35 port and the attached DTE
port, support ANSI Annex A, CCITT Q933 Annex D, CISCO LMI or Static (no signaling).
LAN FR POLL TIMEOUT
T392 (5-30)
T392 for signaling protocol, typical value 15. No
meaning if Maint Protocol is Static.
FRN PORT CONFIG
Logical Frame Relay ports over ATM. Up to 4
ports are supported with each port supporting up
to 4 DLCI mappings. Go to NUM field. Typing "i"
or "I" will insert another entry, and typing "d" or
"D" will delete one entry.
NAME
To identify your port.
ATM VPI
Specifies the virtual path over which this
logical port is running.
$709&,
Specifies the virtual circuit over which this
logical port is running.
DE MAP
Frame Relay to ATM DE mapping; default
value (Frn Only, ATM 0) suggested.
&/3,0$3
ATM to Frame Relay CLPI map; default
value (Frn Only) suggested.
'&
Set D/C field in the header to 0 or 1.
+($'(5
Header format; only 2 bytes supported now.
0$,1735272&2/
Maintenance or signaling protocol over this
logical Frame Relay port. Support Annex A,
Annex D, CISCO LMI or Static.
08;02'(
Many DLCIs or one DLCI mapping over this
port.
'/&,0$3
Actual DLCI mappings.
/$1'/&,
The DLCI configured over local V.35
Frame Relay port.
1(7'/&,
The DLCI configured over the WAN
side logical Frame Relay port.
$&7,9(
Always active, not configurable.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 53
The following settings are used for FRF8.
© 2002, ADTRAN, Inc.
LAN FR MAINT PROTOCOL
Frame Relay maintenance or signaling protocol
between local V.35 port and the attached DTE
port, support ANSI Annex A, CCITT Q933 Annex D, CISCO LMI or Static (no signaling).
LAN FR POLL TIMEOUT
T392 (5-30)
T392 for signaling protocol, typical value 15. No
meaning if Maint Protocol is Static.
FR/ATM PVC MAPPING
Up to 4 mappings are supported.
FR DLCI
Frame Relay DLCI on V.35 port.
ATM VPI
Specifies the virtual path to which DLCI is
mapped.
$709&,
Specifies the virtual circuit to which DLCI is
mapped.
TRANSLATE
Translate or transparent mode between
Frame Relay frames and ATM cells.
'(0$3
Map Frame Relay DE bit to ATM CLPI bit,
Always 0, Always 1 or Convert each other.
)(&10$3
Map Frame Relay FECN bit to ATM EFCI
bit, Always 0, Always 1 or Convert each
other.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 54
Appendix A. Updating Total Access 600 Firmware using XMODEM
The Total Access 600 supports firmware updating using XMODEM transfer protocol via the base unit’s CRAFT port.
XMODEM is found in the VT 100 terminal emulation application in the ADTRAN Utilities package and in most PC
VT 100 communications software packages.
Make certain that the communications software package has flow control turned off.
Before beginning this procedure, you must obtain the appropriate update file from ADTRAN Technical Support at
(888) 4ADTRAN (423-8726).
An XMODEM download can be initiated by enabling a forced download or by using the console menus. The following materials are required.
•
•
VT 100 terminal or PC with VT 100 terminal emulation software
XMODEM software
To prevent electrical shock, do not install equipment in a wet location or during a lightning
storm.
Updating Firmware via a Forced Download
Perform the Steps Below in the Order Listed
1.
Using a VT 100 terminal emulation communication software package which contains XMODEM protocol support, log in to TA 600. Set the transmit rate of the emulation software to
9600 baud.
2.
Unplug the unit to remove power. When power is reapplied, hold down the letter 'B' from
the VT 100 terminal. Before the unit begins its boot-up sequence it will check for the letter
'B'. If present, the download menu will appear.
Both uppercase and lowercase letters will work for the Forced Download. Make certain flow
control is disabled for the VT 100 interface.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 55
3.
Press (QWHUuntil a menu appears.
To shorten transmit time, select the option from the menu to change the transmit rate to 115.2k baud
or the highest rate supported by the terminal emulation software. If this transmit rate is changed,
change emulation software properties to match this rate and disconnect and connect again. Press
(QWHU again until the menu appears.
4.
Choose option 1, %(*,1;02'(0'2:1/2$'12:, from the menu to start the XMODEM file
download.
5.
Press < at the 67$57)/$6+'2:1/2$'12: prompt to continue with the XMODEM file transfer.
When Total Access 600 is ready to receive the XMODEM upload, the menu screen will display
7UDQVPLW)ODVKGRZQORDGILOHQRZ. If this does not appear, please review the steps above for
possible configuration errors.
6.
From the terminal emulation software, begin the XMODEM upload by using the appropriate
command sequence. (If necessary, refer to terminal emulation software documentation for
help. Also, when specifying the filename, ensure that the file transferred is the one provided by ADTRAN. Otherwise, the update will not complete successfully.)
Because XMODEM data is being transferred in-band through the menu interface, the VT 100
menus of Total Access 600 will be inoperable from the &5$)7 port.
7.
When the update has successfully completed, 75$16)(5&203/(7( appears in the terminal
window. If an error occurs during the update, an error message will display in the terminal
window. If this occurs, return to Step 3 and attempt the update again. If the same error
occurs, contact ADTRAN Technical Support.
8.
After the 75$16)(5&203/(7(message has been displayed, cycle power on the unit.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 56
9.
Change the emulation software properties to 9600 baud. Disconnect and connect to the
unit at this transmit rate and continue configuring the unit as normal.
It is suggested that a factory default be conducted after the unit is updated with new firmware.
Updating Firmware via the Console Menus
1.
Using a VT 100 terminal emulation communication software package which contains XMODEM protocol support, log in to TA 600.
2.
Select 6<67(087,/,7</83'$7(),50:$5(.
3.
Select ;02'(0 for 75$16)(50(7+2'.
4.
Press (QWHUon 67$5775$16)(5!
5.
When prompted, press < to erase flash.
When Total Access 600 is ready to receive the XMODEM upload, the menu screen will clear and
display 7UDQVPLW)ODVKGRZQORDGILOHQRZ. If this does not appear, please review the steps
above for possible configuration errors.
6.
From the terminal emulation software, begin the XMODEM upload by using the appropriate
command sequence. (If necessary, refer to terminal emulation software documentation for
help. Also, when specifying the filename, ensure that the file transferred is the one provided by ADTRAN. Otherwise, the update will not complete successfully.)
Because XMODEM data is being transferred in-band through the menu interface, the VT 100
menus of Total Access 600 will be inoperable from the &5$)7 port.
7.
When the update has successfully completed, 75$16)(5&203/(7( displays in 75$16)(5
67$786. The module restarts immediately and resumes operation. If an error occurs during
the update, an error message will display in the 75$16)(567$786 field. If this occurs, return
to Step 3 and attempt the update again. If the same error occurs, contact ADTRAN Technical Support.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 57
Appendix B. Updating Total Access 600 Firmware using TFTP
TA 600 supports firmware updates via the IP network using TFTP from a network server. The network server must be
capable of supporting TFTP server requests from the TFTP client within the TA 600.
You must have a level 2 password to perform updates to the Total Access 600. Please consult the Total Access 600
administrator if this password is not known.
You must obtain the appropriate update file from ADTRAN Technical Support at (888) 4ADTRAN (423-8726).
You must copy the update file provided by ADTRAN to a network server that supports TFTP server requests. Record
both the IP address of the server and the full path location of the update file to be downloaded.
The following materials are required.
•
•
A PC with a Telnet client software
A TFTP Server accessible on the local network (a TFTP Server is provided as part of the ADTRAN Utilities
software)
To prevent electrical shock, do not install equipment in a wet location or during a lightning
storm.
Electronic modules can be damaged by static electrical discharge. Before handling modules, wear
an antistatic discharge wrist strap to prevent damage to electronic components. Place modules in
antistatic packing material when transporting or storing. When working on modules, always place
them on an approved antistatic mat that is electrically grounded.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 58
Perform Steps Below in the Order Listed
1.
Using a Telnet program,ORJLQ to Total Access 600.
2.
Select 6<67(087,/,7<83'$7(),50:$5(.
3.
Select 7)73 for 75$16)(50(7+2'.
4.
Enter into TFTP SERVER IP ADDRESS, the IP address of the network server that was recorded
earlier.
5.
Enter into TFTP SERVER FILENAME, the full path name and filename of the update file that
was recorded earlier.
6.
Select 67$5775$16)(5! to start the update process. Enter < to confirm the transfer and
to set up the module to receive the TFTP upload.
During the TFTP upload process, various status messages display in &855(1783'$7(67$786
to indicate progress. The table below describes these messages.
When the update has successfully completed, 75$16)(5&203/(7( displays in 75$16)(567$786. The Total
Access 600 restarts immediately and resumes operation.
If an error occurs during the update, an error message will display in the 75$16)(567$786 field. If this occurs,
return to Step 3 and attempt the update again. If the same error occurs, contact ADTRAN Technical Support.
During the TFTP upload, various status messages display to indicate progress. The following table describes these
messages.
Message
Meaning
Contacting Server
Indicates communication with the TFTP network server
is trying to be established with the specified server
address in the TFTP Server IP Address field.
Beginning TFTP
Transfer
Indicates communication with the TFTP network server
has been established and the update file is being transferred between Total Access 600 and the TFTP network
server.
Completed
Indicates the Total Access 600 product successfully
received the update file.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 59
Message
Error: File Not Found
Meaning
Indicates the TFTP network server was unable to locate
the specified file name or path in the TFTP Server Filename field.
Error: Access Violation Indicates the TFTP network server denied Total Access
600 access to the given update file name and path.
Please verify appropriate user rights are selected for the
specified path.
Error: Illegal Operation An unknown operation was detected by Total Access
600 when transferring the update file from the TFTP
network server.
Error: User Aborted
© 2002, ADTRAN, Inc.
Indicates the user selected &$1&(/83'$7( to abort
reception of the update file from the TFTP network
server.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 60
Appendix C. Navigating the Terminal Menus
Terminal Menu Window
The TA 600 uses a multilevel menu structure that contains both menu items and data fields. All menu items and data
fields display in the terminal menu window, through which you have complete control of the TA 600 (see Figure 19).
Menu Path
Right Pane
Left Pane
Status Bar
Mode
Navigation Help
System Time
Figure 19. Top-level Terminal Menu Window
Menu Path
The first line of the terminal menu window (the menu path) shows the session’s current position (path) in the menu
structure. For example, Figure 19 shows the top-level menu with the cursor on the SYSTEM INFO submenu; therefore,
the menu path reads TOTAL ACCESS 600 IAD/SYSTEM INFO.
The top level menu will always display the specific product name from the Total Access 600 family.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 61
&75/: must be invoked to save configuration changes to non-volatile memory.
Window Panes
When you first start a terminal menu session, the terminal menu window is divided into left and right panes. The left
pane shows the list of available submenus, while the right pane shows the contents of the currently selected submenu.
Window Pane Navigation
Use the following chart to assist you in moving between and within the two window panes.
To move...
Press one of these keys...
From left pane to right pane
Tab
Enter
Right arrow
From right pane to left pane
Tab
Escape
Left arrow
Within each pane
Up arrow
Down arrow
Left arrow
Right arrow
Right Window Pane Notation
The right window pane shows the contents of the currently selected menu. These contents can include both
submenu items and data fields. Some submenus contain additional submenus and some data fields contain
additional data fields. The following chart explains the notation used to identify these additional items.
This notation...
Means that...
[+]
More items are available when selected.
[DATA]
More items are available when selected.
<+>
An action is to be taken, such as activating a test.
Highlighted menu item
You can enter data in this field.
Underlined field
The field contains read-only information.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 62
Additional Terminal Menu Window Features
Mode
Describes the mode of the Total Access 600 base unit
(system).
Port Status
Indicates the types of modules installed in ports 1—6.
Navigation Help
Lists characters used for navigating the terminal menu (&WUO
=). See also Moving through the Menus below.
System Time
Displays current time. See Date/Time on page 20 for details
on editing the time.
Navigating Using the Keyboard Keys
You can use various keystrokes to move through the terminal menus, to manage a terminal menu session, and to configure the system. Press&WUO= to activate a pop-up screen listing the navigation keystrokes.
Moving through the Menus
To do this...
Press this key...
Return to the home screen.
H
Jump between two menu items.
J
Press J while the cursor is located on a menu item, and you jump back to the
main screen.
Go to another menu item, press J, and you jump back to the screen that was
displayed the first time you pressed J.
Press J when you want to jump between these items.
Select items.
Arrows
Edit a selected menu item.
Enter
Cancel an edit.
Escape
Close pop-up help screens.
Escape
Move between the left and right panes.
Tab or
Arrows
Move to the top of a screen.
A
Move to the bottom of a screen.
Z
Ascend one menu level.
Backspace
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 63
Session Management Keystrokes
To do this...
Press this...
Log out of a session.
Ctrl-L
Invalidate the password entry and return to the login screen.
Ctrl-S
Refresh the screen.
Ctrl-R
To save time, only the portion of the screen that has changed is refreshed.
This option should be necessary only if the display picks up incorrect
characters.
Configuration Keystrokes
To do this...
Press this key...
Restore factory default settings.
F
This setting restores the factory defaults based on the location of the cursor. If the
cursor is on a module line (in the MODULES menu), then only the selected module is
updated to factory defaults.
Copy selected items to the clipboard.
C
The amount of information you can copy depends on the cursor location when you
press C:
•
If the cursor is over an editable field, only that item is copied.
•
If the cursor is over the index number of a list, then all of the items in the row of the
list are copied. For example, if the cursor is over the SLOT # field in the MODULES
screen, all of the information associated with the slot is copied.
P
Paste the item stored in the clipboard, if the information is compatible.
You must confirm all pastes—except those to a single editable field.
Increment the value of certain types of fields by one when you paste information into
those fields.
>
Decrement the value of certain types of fields by one when you paste information into
those fields.
<
Insert a new list item.
I
For example, add a new item to the PVC MAPPING by pressing I while the cursor is
over an index number.
Delete a list item.
D
For example, delete an item from the PVC MAPPING by pressing D while the cursor is
over the index number.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 64
Getting Help
The bottom line of the terminal menu window contains context-sensitive help information. When the cursor is positioned over a set of configuration items, a help message displays (when available) providing a description of the item.
When more detailed help is available for a particular item, A$ displays at the bottom of the window. At this point, if
you press &WUO$a pop-up help screen displays with information about the item.
Press &WUO= to activate the help screen that displays the available keystrokes you can use to navigate the terminal
menus.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 65
Appendix D. Voice Gateway Quick Start Procedure (Voice Turn up)
A typical VoATM application (see Figure 20) uses a Total Access 600 connected to an ATM network. For voice applications, a Voice Gateway is needed to interface with the PSTN. Jetstream, Tollbridge, and CopperCom are popular
Gateway types.
SCU
1181015L1
DS3MX
1181020L1
POWER
STATUS
TEST
DS3MX
1181020L1
POWER
STATUS
TEST
MODE
HD-10 BRI Mux
HD-10 BRI Mux
HD-10 BRI Mux
HD-10 BRI Mux
QFC-C QFC-C QFC-C QFC-C T1-OR T1-OR T1-OR T1-OR HTU-C
HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C HTU-C
POWER
POWER
POWER
HTU-C HTU-C HTU-C HTU-C
POWER
PWR
PWR
PWR
PWR
1181200L1
1181200L1
1181200L1
1181200L1
DSX
DSX
DSX
DSX
LBK
LBK
LBK
LBK
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
DSX
8
8
8
8
TST
TST
TST
TST
9
9
9
ALM
ALM
ALM
ALM
SELECT
HST
ACO
FSE
ALM
ACO
LOCKOUT
C
ON LINE
LOCKOUT
ON LINE
R
A
APS
APS
TEST/
TEST/
ENABLE
ENABLE
F
T
1181300L1
10
10
10
DSL
DSL
DSL
1181300L1
1181310L1
1181300L1
1181310L1
1181310L1
1181310L1
1181101L1
PWR
DSX
DSX
LBK
+
DSX
#1
DSX
#1
DSX
#1
#2
DSX
#2
DSX
#2
DSX
#2
#3
DSX
#3
DSX
#3
DSX
#3
#4
DSX
#4
DSX
#4
DSX
#4
6V
A
ACT
P
GRN = NORM
YEL = MAN
S
A
ACT
P
GRN = NORM
YEL = MAN
LINK
S
A
ACT
P
GRN = NORM
YEL = MAN
DSX
S
V.35 RX
GRN = NORM
YEL = MAN
–
+
T
R
X
X
6V
–
R
X
6V
–
R
X
6V
–
TX
TX
M
O
N
M
O
N
M
O
N
RX
RX
RX
T
R
X
X
RX
A ACT
A ACT
A ACT
P
P
P
P
S
S
GRN = NORM
YEL = MAN
V.35 TX
S
GRN = NORM
YEL = MAN
DATA
S
GRN = NORM
YEL = MAN
S
VOICE
RX
RX
TX
TX
TX
GRN = NORM
YEL = MAN
BATT
RX
RX
RX
RX
ACT
ACT
ACT
ACT
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
M
O
N
RX
ACT
GRN=NORM
YEL=MAN
M
O
N
RX
DSX
TST
LP1
TST
LP1
LP2
LP1
LP2
LP2
ALM
TX
ALM
TX
E
Q
TX
E
Q
RX
E
Q
RX
TX
RX
TX
M
O
N
TX
M
O
N
RX
1181101L1
PWR
DSX
TST
M
O
N
RX
1181101L1
PWR
DSX
ALM
E
Q
TX
M
O
N
RX
1181101L1
PWR
TX
RX
TX
RX
1181101L1
LP2
RX
M
O
N
RX
ALM
TX
E
Q
RX
TX
M
O
N
LP1
LP2
RX
TX
M
O
N
TST
LP1
E
Q
RX
TX
M
O
N
DSX
TST
ALM
TX
RX
TX
M
O
N
PWR
DSX
LP2
RX
TX
M
O
N
1181101L1
PWR
LP1
E
Q
RX
TX
RX
A ACT
P
TST
ALM
TX
E
Q
RX
M
O
N
A
DSX
LP2
ALM
TX
1181101L1
PWR
LP1
LP2
E
Q
1181101L1
TST
LP1
ALM
TX
E
Q
DSX
TST
LP2
ALM
TX
PWR
DSX
LP1
LP2
1181101L1
PWR
TST
LP1
E
Q
1181101L1
DSX
TST
ALM
TX
E
Q
PWR
DSX
LP1
LP2
ALM
TX
1181101L1
PWR
TST
LP2
E
Q
1181101L1
DSX
LP1
ALM
TX
E
Q
PWR
TST
LP2
ALM
TX
1181101L1
DSX
LP1
LP2
ALM
+
T
X
TX
M
O
N
PWR
TST
LP1
ALM
+
T
X
TX
1181101L1
DSX
TST
LP
ALM
PWR
DSX
LBK
LP
ALM
PWR
#1
DSX
ACT
TX RX
PWR
LBK
LP
ALM
PWR
DSX
LBK
LP
9
10
DSL
1181300L1
PWR
DSX
DSX
M
O
N
RX
RX
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
ACT
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
GRN=NORM
YEL=MAN
PWR/NET
Figure 20. Application Diagram
To configure a Total Access 600 for use with the Voice Gateway, you need to know the VPI and VCI to be used on
the ATM network. You also need to know the format for Idle Cells and whether Data Scrambling is used on this ATM
network. The following procedure will help you navigate the Total Access 600 menus for configuring the necessary
elements for VoATM with the Voice Gateway.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 66
Voice Turn Up
Step
Action
1
From the Total Access 600 main menu, select the WAN menu. Select
DSLAM TYPE and select the name of the DSLAM type you are using.
(At this point you need to back out of the menu to save the changes.
The unit will need to reboot if it was not previously configured for this
DSLAM type.)
2
Select DSL RATE CONFIG (BIT RATE) and change the setting to match
that in your DSLAM. (If this field is read-only, allow a few seconds for
autobaud to expire and the field will change to writeable.)
3
Select WAN, and then select the ATM CONFIG menu.
4
Enter the IDLE CELLS format for your network.
5
Set DATA SCRAMBLING appropriately for your network.
6
Back all the way out to the top level Total Access 600 menu, and then
select the VOICE menu. (From this menu, the appropriate Voice
information for working with the Voice Gateway is entered.)
7
Select CONFIG, and from the CONFIG menu, enter the Gateway type
under CALL CONTROL and enter the VPI and VCI values for
communicating with that Gateway.
CALL CONTROL should be set to the Gateway type, and the VPI and VCI
values should be set appropriately for your network.
To verify correct setup, use the STATUS menu (under the VOICE menu)
to look at the current status of the voice connection.
8
Under STATUS, you can view the GATEWAY STATS and information
about the voice PVC along with information about the POTs ports
available on the Gateway.
The GATEWAY STATS menu should show the Gateway Link is up (if
everything is configured correctly).
A visual inspection of the VOICE LED on the front panel will also yield
the status. Green = Up. Red = Down.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 67
Appendix E. RFC1483 Quick Start (IP Routing)
The Total Access 600 allows for complete integration of voice and data delivery from one compact platform (see Figure 21). Once you have completed the voice turn up procedure from the previous example, adding data to the circuit
requires some additional setup.
TX RX
LINK
V.35 RX
V.35 TX
DATA
VOICE
BATT
PWR/NET
Figure 21. Application Diagram
To configure a Total Access 600 for IP routing, you need to know the VPI and VCI values for the data circuit on your
network. You also need the IP address of the next hop router in the circuit.
The table on the next page shows how to configure the Total Access 600 for IP Routing.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 68
..
IP Routing
Step
Action
1
From the Total Access 600 main menu, select the WAN menu. (Here
you set up the ATM network.)
2
Select the ATM CONFIG menu.
3
Enter the IDLE CELLS format for your network.
4
Set DATA SCRAMBLING appropriately for your network.
5
Back all the way out to the top level Total Access 600 menu, and then
select the ROUTER menu.
Select CONFIGURATION.
6
From the CONFIGURATION menu, you will set up addresses for your LAN
and WAN.
For basic IP routing, use all the default values from the GLOBAL menu.
7
8
From the ETHERNET menu, enter the IP menu to enter your LAN
configuration.
Enter your LAN IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY
information.
For this example, the IP ADDRESS is 192.168.1.2, the SUBNET MASK is
255.255.255.0, and the DEFAULT GATEWAY is 10.25.4.10.
9
Arrow back to the main ROUTER CONFIGURATION menu, and select the
WAN menu and then the ATM menu. (Here you will enter your data
PVC information.)
10
Create a new PVC by entering the menu. Enter your VPI and VCI
values.
From the RFC1483 IP menu, enter your LAN information.
11
12
For this example, the FAR END IP ADDRESS is 10.25.4.9, the IP
NETMASK is 255.255.255.252, and the LOCAL IP ADDRESS is 10.25.4.10.
Arrow back to the top level Total Access 600 menu to activate your
changes.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 69
Appendix F. RFC1483 Quick Start (IP Routing with NAT)
To illustrate the use of NAT, consider the example from Appendix E. To set up a single public address that will be
used to access the public network, you will use the NAT menu on the WAN/ATM/RFC1483 IP menu.
IP Routing with NAT
Step
Action
1
From the NAT menu, set NETWORK ADDRESS PORT TRANSLATION to
ENABLED. (This will enable translation and allow you to enter the NAT
options.)
2
Set PUBLIC IP ADDRESS MODE to SPECIFIED so you can enter your public
address. During transmission, private addresses are translated into this
public (NAPT) address.
You will also need to set up the Translation Table to do translation on
the body of the packets for certain protocols, such as FTP, to work
correctly.
© 2002, ADTRAN, Inc.
3
From the TRANSLATION TABLE menu, create a new entry by arrowing
into the table.
4
For PUBLIC ADDRESS MODE, select NAPT ADDRESS to use the
previously specified public address.
5
For PROTOCOL, select TCP.
6
Make sure that TRANSLATE BODY is set to YES.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 70
Appendix G. RFC1483 Quick Start (Bridging)
The Total Access 600 allows for complete integration of voice and data delivery from one compact platform. Once
you have completed the voice turn up procedure from the previous example, adding data to the circuit requires some
additional setup.
To configure a Total Access 600 for Bridging, you need to know the VPI and VCI values for the data circuit on your
network.
Bridging
Step
Action
1
From the Total Access 600 main menu, select the WAN menu. (Here
you set up the ATM network.)
2
Select the ATM CONFIG menu.
3
Enter the IDLE CELLS format for your network.
4
Set DATA SCRAMBLING appropriately for your network.
5
Back all the way out to the top level Total Access 600 menu, and then
select the ROUTER menu.
Enter the CONFIGURATION menu.
6
From this menu, you will set up addresses for your LAN and WAN.
For basic IP routing, use all the default values from the GLOBAL menu.
7
From the ETHERNET menu, enter the IP menu to enter your LAN
configuration.
Enter your LAN IP ADDRESS and SUBNET MASK.
8
For this example, the IP ADDRESS is 192.168.1.2 and the SUBNET MASK
is 255.255.255.0. This is not required, but will allow Telnet configuration
and TFTP upgrades from the LAN.
9
Arrow back to the main ROUTER CONFIGURATION menu, and select the
WAN menu and then the ATM menu. (Here you will enter your data
PVC information.)
10
Create a new PVC by entering the menu. Enter your VPI and VCI
values.
11
Disable IP on the RFC1483 IP menu and enable Bridging on the
RFC1483 BRIDGE menu. (This enables the Total Access 600 as a
bridge.)
12
Arrow back to the top level Total Access 600 menu to activate your
changes.
All packets that come in on the Ethernet will be forwarded on the WAN.
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 71
Appendix H. Craft Port Connection Pin-out
DB-9
RJ-45
Description
2
5
TX Data
3
3
RX Data
5
1
GND
Note: All other pins are unused.
© 2002, ADTRAN, Inc.
Total Access 600 Series User Manual
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 72
Total Access 600 Series User Manual
© 2002, ADTRAN, Inc.