Advantech EKI-2525P Network Card User Manual

EKI-2525P
5-port Industrial PoE Unmanaged
Ethernet Switch
User Manual
Copyright
The documentation and the software included with this product are copyrighted 2007 by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time without notice. No part of
this manual may be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of Advantech Co., Ltd. Information provided in this
manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements of the rights of third parties, which may
result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Part No.
Printed in China
EKI-2525P_Manual_ed1
1st Edition
November 2007
ii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons
other than repair personnel authorized by Advantech, or which have been subject to misuse,
abuse, accident or improper installation. Advantech assumes no liability under the terms of
this warranty as a consequence of such events.
Because of Advantech′s high quality-control standards and rigorous testing, most of our
customers never need to use our repair service. If an Advantech product is defective, it will be
repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you
will be billed according to the cost of replacement materials, service time and freight. Please
consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU speed,
Advantech products used, other hardware and software used, etc.) Note anything
abnormal and list any onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any
helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement Order
Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable
container. A product returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to your
dealer.
iii
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions for
passing included the equipment being operated within an industrial enclosure. In order to
protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage,
we strongly recommend the use of CE-compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Technical Support and Assistance
Step 1.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Step 2.
Contact your distributor, sales representative, or Advantech’s customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, application software,
etc.)
- A complete description of the problem
- The exact wording of any error messages
EKI-2525P_Manual_ed1
iv
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not
use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and
must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may
cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's
manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -40 ℃ (-40℉) OR ABOVE 85 ℃ (185 ℉ ). THIS
COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.
v
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from damage.
1. To avoid electrical shock, always disconnect the power from your PC chassis before you
work on it. Don't touch any components on the CPU card or other cards while the PC is
on.
2. Disconnect power before making any configuration changes. The sudden rush of power
as you connect a jumper or install a card may damage sensitive electronic components.
EKI-2525P_Manual_ed1
vi
Chapter 1
Contents
Overview........................................... 2
1.1 Introduction ......................................................... 2
1.1.1 High-Speed Transmissions ....................... 2
1.1.2 Power-over-Ethernet (PoE) ....................... 2
1.1.3 Dual Power Input ....................................... 2
1.1.4 Flexible Mounting ...................................... 2
1.1.5 Advanced Protection ................................. 2
1.1.6 Wide Operating Temperature .................... 2
1.1.7 Easy Troubleshooting................................ 2
1.2 Features.............................................................. 3
1.3 Specification ....................................................... 4
1.4 Packing List ........................................................ 6
1.5 Safety Precaution ............................................... 6
Chapter 2
Installation........................................ 8
2.1 LED Indicators .................................................... 8
Table 2.1: EKI-2525P LED Definition..........................8
2.2 Dimensions (units: mm) ...................................... 9
Figure 2.1: Front View of EKI-2525P...........................9
Figure 2.2: Side View of EKI-2525P ..........................10
Figure 2.3: Rear View of EKI-2525P..........................11
Figure 2.4: Top View of EKI-2525P ...........................12
2.3 Mounting ........................................................... 13
2.3.1 Wall mounting.......................................... 13
Figure 2.5: Combine the Metal Mounting Kit (units:
mm)..............................................................................13
2.3.2 DIN-rail Mounting..................................... 14
Figure 2.6: Installation to DIN-rail Step 1...................14
Figure 2.7: Installation to DIN-rail Step 2...................15
2.4 Network Connection ......................................... 16
2.5 Power Connection ............................................ 16
Figure 2.8: Pin Assignment of the Power Connector ..16
Chapter 3 Troubleshooting ............................ 18
Appendix A Pin Assignment & Wiring ........... 20
Figure A.1: RJ-45 Pin Assignment..............................20
Figure A.2: EIA/TIA-568B .........................................20
Figure A.2: EIA/TIA-568A .........................................20
vii
Contents
EKI-2525P_Manual_ed1
viii
CHAPTER
Overview
Sections include:
z
Introduction
z
Features
z
Specifications
z
Packing List
z
Safety Precaution
1
Chapter1
Chapter 1
Overview
1.1 Introduction
The EKI-2525P is a cost-effective solution and meets the high reliability requirements
demanded by industrial applications. Using fiber port can extend the connection
distance that increases the network elasticity and performance. Besides, the industrial
switch provides the PoE function for kinds of Powered Devices to receive power as
well as data over the RJ-45.
1.1.1
High-Speed Transmissions
The EKI-2525P includes a switch controller that can automatically sense transmission
speeds (10/100 Mbps). The RJ-45 interface can also be auto-detected, so MDI or MDIX is automatically selected and a crossover cable is not required. All Ethernet ports
have memory buffers that support the store-and-forward mechanism. This assures that
data is properly transmitted.
1.1.2
Power-over-Ethernet (PoE)
PoE eliminates the need to run AC power to other devices on a wired LAN. While using
Power-over-Ethernet system, installers need to run only a single Category 5 Ethernet
cable that carries both power and data to each device. This allows greater flexibility in
the locating of network devices and significantly decreasing installation costs in many
cases.
1.1.3
Dual Power Input
EKI-2525P redundant power input design is with power reserve protection to prevent
the switch device broken by wrong power wiring. When one of power input is fail, PFail LED will turn on and send an alarm through a relay output for notifying user.
1.1.4
Flexible Mounting
EKI-2525P is extremely compact (37 x 140 x 95 mm) and can be mounted on a DINrail or a panel, so it is suitable for any space-constrained environment.
1.1.5
Advanced Protection
EKI-2525P supports up to 3,000 VDC surge protection for power line, and also
supports 4,000V ESD for Ethernet ports. With these 2 strong protections, it can secure
equipment against unregulated voltage and make systems safer and more reliable.
Further, EKI-2525P provides currency overload protection with a resettable fuse to
ensure that the device component won’t be damaged by overload current.
1.1.6
Wide Operating Temperature
The operating temperature of the EKI-2525P is between -10 ~ 60 ℃. With such a wide
range, you can use the EKI-2525P in some of the harshest industrial environments that
exist.
1.1.7
Easy Troubleshooting
LED indicators make troubleshooting quick and easy. Each 10/100 Base-TX port has 2
LEDs that display the link status, transmission speed and collision status. Also the
three power indicators P1, P2 and P-Fail help you diagnose immediately.
EKI-2525P_Manual_ed1
2
1.2 Features
•
•
•
•
•
•
•
•
•
•
Provides 5 x 10/100Base-TX Ethernet ports with 4 PoE injectors of RJ-45 connector
Supports full/half duplex flow control
Supports store and forward transmission
Supports auto-negotiation
Supports MDI/MDI-X auto crossover
Provides surge protection (EFT) 3,000 VDC for power line
Supports 4,000 VDC ESD protection for Ethernet
Supports 48 VDC power input
Provides flexible mounting: DIN-rail, Wall Mounting
Supports operating temperature from -10 ~ 60 ℃
3
Chapter1
1.3 Specification
Communications
IEEE 802.3, 802.3u, 802.3x, 802.3af
10/100Base-TX
Up to 100 m
Up to 100 Mbps
Compatibility
LAN
Transmission Distance
Transmission Speed
Interface
5 x RJ-45
6-pin removable screw terminal
(power & relay)
Unit: P1, P2, P-Fail
TX port: Link/Active, Duplex/Collision
Connectors
LED Indicators
Power
57 Watts (Full load with PoE)
2 x Unregulated 48 VDC
1 Relay Output
Power Consumption
Power Input
Fault Output
Mechanism
37 x 140 x 95
IP30, Metal shell with solid mounting kits
DIN-rail, Wall
Dimensions (WxHxD)
Enclosure
Mounting
Protection
4,000 VDC
3,000 VDC
Yes
0.9A@48VDC (25℃)
ESD (Ethernet)
Surge (EFT for power)
Power Reverse
Current Overload Protection
Environment
-10 ~ 60 ℃
5% ~ 95% (non-condensing)
-40 ~ 85 ℃
Operating Temperature
Operating Humidity
Storage Temperature
EKI-2525P_Manual_ed1
4
Certifications
UL, 60950-1, CAN/CSA-C22.2 No.60950
U.S.A.: FCC Part 15 CISPR 22
EU: EN55011, EN61000-6-4
EN55022, Class A,
EN61000-3-2/3
EN55024
IEC61000-4-2/3/4/5/6/8/11/12
EN61000-6-2/4
IEC60068-2-32
IEC60068-2-27
IEC60068-2-6
Safety
EMC
Free Fall
Shock
Vibration
5
Chapter1
1.4 Packing List
•
•
•
•
•
•
1 x EKI-2525P Industrial Ethernet Switch
1 x eAutomation Industrial Communication CD-ROM with software, and User manual
2 x Wall Mounting Bracket and Screws
1 x DIN-rail Mounting Bracket and Screws
1 x EKI-2525P Startup Manual
1 x DC Jack Cable 2.0/150mm
1.5 Safety Precaution
Attention
IF DC voltage is supplied by an external circuit, please use a protection device
on the power supply input.
EKI-2525P_Manual_ed1
6
CHAPTER
Installation
Sections include:
z
LED Indicators
z
Dimensions
z
Mounting
z
Network Connection
z
Power Connection
7
Chapter2
Chapter 2
Installation
In this chapter, you will be given an overview of the EKI-2525P hardware installation
procedures.
2.1 LED Indicators
There are few LEDs display the power status and network status located on the front
panel of EKI-2525P, each of them has its own specific meaning as the table below.
Table 2.1: EKI-2525P LED Definition
LED
Color
P1
Green
P2
P-Fail
FWD (1 ~ 4)
Link/Active
(1~5)
Duplex/Collision
(1~5)
Description
On
Power input 1 is active
Off
Power input 1 is inactive
On
Power input 2 is active
Off
Power input 2 is inactive
On
Power input 1 or 2 is inactive
Off
Power input 1 and 2 are both active, or no power input
On
A device is connected utilizing Power over Ethernet on the
corresponding port
Off
No device attached or power over Ethernet function failed
On
Connected to network
Flashing
Networking is active
Off
Not connected to network
On
Ethernet port full duplex
Flashing
Collision of packets occurs
Off
Ethernet port half duplex or not connect to network
Green
Red
Green
Green
Yellow
EKI-2525P_Manual_ed1
8
2.2 Dimensions (units: mm)
Figure 2.1: Front View of EKI-2525P
9
Chapter2
Figure 2.2: Side View of EKI-2525P
EKI-2525P_Manual_ed1
10
Figure 2.3: Rear View of EKI-2525P
11
Chapter2
Please refer to page 16 for pin assignment.
Figure 2.4: Top View of EKI-2525P
EKI-2525P_Manual_ed1
12
2.3 Mounting
The EKI-2525P supports two mounting methods: DIN-rail & Wall.
2.3.1
Wall mounting
EKI-2525P can be wall-mounted by using the included mounting kit. Then, hang on the
EKI-2525P to the nails on the wall.
First, use the screws included in the package to combine the EKI-2525P and metal
mounting kit. And then you can install the device firmly via the components, please see
Figure 2.5 as below.
Figure 2.5: Combine the Metal Mounting Kit (units: mm)
13
Chapter2
2.3.2
DIN-rail Mounting
You can also mount EKI-2525P on a standard DIN-rail by below steps.
The DIN-rail kit is screwed on the industrial switch when out of factory. If the DIN-rail kit
is not screwed on the industrial switch, please screw the DIN-rail kit on the switch first.
First, hang the EKI-2525P to the DIN-rail with angle of inclination. See figure 2.6.
Figure 2.6: Installation to DIN-rail Step 1
EKI-2525P_Manual_ed1
14
Then, let the device down straight to slide over the rail smoothly. See Figure 2.7
Figure 2.7: Installation to DIN-rail Step 2
15
Chapter2
2.4 Network Connection
The EKI-2525P has 5 x RJ-45 ports that support connection to 10 Mbps Ethernet, or
100 Mbps Fast Ethernet, and half or full duplex operation. EKI-2525P can be
connected to other hubs or switches through a twisted-pair straight through the cable
or a crossover cable up to 100m long. The connection can be made from any TX port
of the EKI-2525P (MDI-X) to another hub or switch either MDI-X or uplink MDI port.
The EKI-2525P supports auto-crossover to make networking more easy and flexible.
You can connect any RJ-45 (MDI-X) station port on the switch to any device such as a
switch, bridge or router.
2.5 Power Connection
The EKI-2525P supports dual 48 VDC power inputs and power-fail relay output.
Figure 2.8: Pin Assignment of the Power Connector
You can connect an alarm indicator, buzzer or other signaling equipment through the
relay output. The relay opens if power input 1 or 2 fails (‘Open’ means if you connect
relay output with an LED, the light would be off).
EKI-2525P_Manual_ed1
16
CHAPTER
Troubleshooting
17
Chapter2
Chapter 3
Troubleshooting
1.
Power Input
Verify that is using the right power cord/adapter 48 VDC, please don’t use the power
adaptor with DC output voltage higher than 48V, or it will burn this converter down.
2.
Cable
Select the proper UTP cable to construct user network. Please check that is using the
right cable. Use Unshielded Twisted-Pair (UTP) or Shielded Twisted-Pair (STP) cable
for RJ-45 connections: 100 Category 3, 4 or 5 cable for 10 Mbps connections or 100
Category 5 cable for 100 Mbps connections. Also, be sure that the length of any
twisted-pair connection does not exceed 100 meters (328 feet).
3.
Diagnosing LED Indicators
The switch can be easily monitored through panel indicators, which describes common
problems user may encounter and where user can find possible solutions, to assist in
identifying.
If the power indicator does not light up when the power cord is plugged in, user may
have a problem with power cord. Then check for loose power connections, power
losses or surges at power outlet. If user still cannot resolve the problem, contact the
local dealer for assistance.
If the Industrial switch LED indicators are normal and the connected cables are correct
but the packets still cannot transmit, please check your system’s Ethernet devices
configuration or status.
EKI-2525P_Manual_ed1
18
APPENDIX
Pin Assignment & Wiring
19
Chapter2
Appendix A
Pin Assignment & Wiring
It is suggested to adopt ELA/TIA as the wiring of the RJ-45.
Figure A.1: RJ-45 Pin Assignment
Figure A.2: EIA/TIA-568B
Figure A.2: EIA/TIA-568A
EKI-2525P_Manual_ed1
20