ÖKO-LAVAMAT
REGINA 1850 update
The environmentally friendly washing machine
User information
Dear customer,
Please read these user information carefully.
Pay particular attention to the section “Safety information” on the first
few pages. Please retain this user information for later reference. Pass
them on to possible new owners of the appliance.
1
3
2
The following symbols are used in the text:
Safety instructions
Warning: Information concerning your personal safety.
Important: Information on how to avoid damaging the appliance.
Information and practical tips
Environmental information
1. These numbers indicate step by step how to use the appliance.
2. …
3. …
This user information contain information on steps you can take yourself to rectify a possible malfunction. Refer to the section “What to do
if...”.
In the event of any technical problems please contact your nearest customer service centre at any time. (Addresses and telephone numbers
may be found in the appendix under "Customer Service Centres“).
You should also refer to the section "Service".
Printed on recycled paper.
Thinking ecologically means acting ecologically …
2
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Environmental Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Switching on the appliance for the first time – setting the language
9
Description of appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawer for detergent and conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel with display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicators in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
11
11
11
Main control features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching the appliance on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cancelling settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigation display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control knob and pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Buttons and levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting a programme: an example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
12
13
13
14
15
Overview of functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmes (level 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wash programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Options (level 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extras (level 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
17
18
19
20
Preparing a Wash Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sorting and preparing a wash load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of washing and care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washing Detergents and Care Agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Which washing detergent and care agent?. . . . . . . . . . . . . . . . . . . . . . . .
How much washing detergent and care agent? . . . . . . . . . . . . . . . . . . . .
Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
22
23
24
24
24
24
Before the first wash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setting the time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Carrying out a wash programme prior to first use. . . . . . . . . . . . . . . . . . . . . 26
3
Performing a wash cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading the washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding detergents/conditioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting a wash programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set the options, e.g. DELAY START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wash programme progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When the wash programme is complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
27
27
28
29
30
31
32
33
MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Saving a programme setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cancelling a saved programme setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Changing the language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detergent Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washing Drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
40
40
41
41
What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remedying a malfunction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If the washing results are not satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carrying out emergency drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drain pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42
42
47
48
49
Anti-flood system Aqua Control + Aqua Alarm . . . . . . . . . . . . . . . . . . . . 50
What does “UPDATE” mean? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Child Safety Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Consumption values and load sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4
Installation and connection instructions. . . . . . . . . . . . . . . . .
54
Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Installation of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove transport packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prepare the installation place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation on a concrete base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation on vibrating floors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compensate for floor unevenness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
55
55
57
57
58
58
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Permissible water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water inflow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delivery heads over 1m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
59
60
61
61
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Customer Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index
63
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Service
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5
Operating Instructions
1 Safety
The safety aspects of AEG electrical appliances comply with accepted
technical standards and the German Appliance Safety Law. However, as
manufacturers we regard it as our responsibility to inform you about
the following safety instructions.
Before Using for the First Time
• Refer to the "Installation and Connection Instructions" further on
in this user information.
• If units are delivered in the winter months at minus temperatures:
Store the washing machine at room temperature for a few hours before putting it into operation.
Correct Use
• The washing machine is only intended for washing normal domestic
washing. If the appliance is used for a wrong purpose or wrongly operated, the manufacturer cannot assume any liability for any damages.
• Additions or modifications to the washing machine are strictly forbidden due to safety reasons.
• Use only detergent which is suitable for washing machines. Refer to
the detergent manufacturer's instructions.
• The washing must not contain any flammable solvents. Also bear this
in mind when washing pre-cleaned washing.
• Do not use the washing machine for dry-cleaning.
• Dyes /dye-removing agents may only be used in the washing machine
if the manufacturer expressly permits use of these products. We cannot accept liability for any damage.
• Use only water from the water mains. Use rain water or service water
only if it meets the requirements defined in DIN 1986 and DIN 1988.
• Frost damage is not covered by the warranty! If the washing machine
is in a room subject to possible frost hazards, emergency emptying
must be carried out if there is a risk of frost (see the Section "Carrying out emergency emptying“).
6
Child Safety
• Packaging materials (e.g. films, polystyrene) can be dangerous for
children. Risk of suffocation! Keep packaging away from children.
• Children frequently cannot recognise hazards involved in handling
electrical appliances. Therefore, ensure that they are properly supervised during operation and never allow children to play with the
washing machine -there is a risk that they can lock themselves inside it.
• Ensure that children or small animals do not climb into the washing
machine's drum.
• When disposing of washing machines pull out the mains plug, destroy
the door lock, cut off the electrical supply lead and dispose of the
plug and remaining cable. This means that playing children cannot
shut themselves in and cannot encounter a potentially lethal hazard.
General Safety
• Repairs to the washing machine must only be carried out by qualified
personnel. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local AEG Service
Force Centre.
• Never operate the washing machine if the mains cable is damaged or
the control panel, work top or base area are damaged allowing internal components to be accessible.
• Switch off the appliance and isolate from the mains supply before
carrying out any cleaning or maintenance work.
• If operation is stopped, disconnect the appliance from the mains
supply and shut off the tap.
• Do not use the mains cable to pull the plug out of the socket.
• Adapters and extension cables must not be used. There is a danger
of overheating!
• Do not clean the washing machine with a water jet. There is a danger
of electrical shock!
• During high temperature wash programmes, the glass of the door
may become hot. Do not touch!
• Allow the water to cool down before cleaning the drain pump, carrying out emergency emptying or opening the door in an emergency.
• Small animals/pets can chew on power cables and water hoses. This
can cause the danger of an electrical shock to the animal and water
damage to the appliance and property. Keep small animals away from
the appliance.
7
2 Disposal
Disposing of the Packaging Material!
Dispose of the packaging of your washing machine correctly. All pakkaging materials used are environmentally-compatible and recyclable.
• Plastic parts are identified with internationally standardised abbreviations:
>PE<
for polyethylene, e.g. packing films.
>PS<
for polystyrene, e.g. cushion parts (always CFC-free)
>POM< for polyoxymethylene, e.g. plastic clips.
• Cardboard packaging is manufactured from recycled paper and
should be deposited in the waste paper collection for recycling.
Disposing of your old appliance!
When you put your unit out of operation one day, please bring it to
your nearest recycling centre or to your dealer.
2 Environmental Tips
• You do not need to use a pre wash cycle or soak for washing with average soiling. This saves detergent, water and time (and protects the
environment).
• When loaded to the capacities indicated the washing machine is especially efficient.
• For small loads, use only one half to two thirds of the recommended
quantity of detergent.
• By pre-treating stains and marks you will be able to wash at a lower
temperature.
• It is often possible to wash without using softener. Give it a try! If
you use a drier, your washing will be soft and fluffy even without a
softener.
• For medium to high water hardness (from hardness range II, see “Detergents and Conditioners”) you should use water softener. The
detergent can then always be dosed as for hardness range I (= soft).
8
Switching on the appliance for the first time
– setting the language
When switching on the appliance for the first time you must set the
language in which you want the indicators in the display to appear.
1. Turn the appliance on by
pressing the control knob so
that it is no longer flush in
the control panel.
The display in the middle of
the control panel will illuminate, and the appliance is
switched on. The selection of
possible languages will appear in the right of the display.
Important: If the display is not showing any languages, the appliance
has already been switched on once. In such case, go to the chapter
“Change languages” if you would like to change the language setting.
2. Turn the knob until the deEXTRAS
SPRACHE
sired language is highlightÍ
ed by the frame.
§
ANWÄHLEN
ENGLISH§
DEUTSCH)
ITALIANO§
FRANÇAIS§
ZURÜCK
3. Press the SELECT button.
A tick will appear next to the
highlighted language. All indicators in the display will
appear in this language from
now on.
4. Press the control knob to
switch off the appliance.
When the appliance is
switched on again all indicators in the display will appear in this language.
3
EXTRAS
LANGUAGE
Í
§§
ENGLISH!)
DEUTSCH§§
ITALIANO§§
FRANÇAIS§§
SELECT
BACK
EXTRAS
LANGUAGE
Í
SELECT
BACK
§§
ENGLISH!)
DEUTSCH§§
ITALIANO§§
FRANÇAIS§§
Before starting a wash cycle, please first read the chapter “Before the
first wash”.
9
Description of appliance
Front view
Control panel with display
Drawer for
detergent and
conditioner
Rating plate
(behind door)
Door
Screw feet
(height adjustable);
rear left:
automatic
adjustment foot
Drain pump
cover
Drawer for detergent and conditioner
Stain removal agent
Detergent for main
wash (in powder
form) and watersoftener if necessary
10
Pre-wash detergent
or water softener
Liquid conditioners
(softeners, stiffeners,
starch)
Control panel with display
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
Fî
START
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
60°
1800
OPTIONS
Buttons
Display
Control knob
Indicators in the display
Information panel
shows the current
settings
Symbol row
shows options
selected and
extras
LINEN/EASY-C. 60°C
1800 RPM
START
60°
1800
OPTIONS
10:17-12:16
Fî
Navigation
display
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
Selection
Wash programme,
options,
extras
Information panel
Programme
Spin speed
Temperature
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
Current time –
end time of
selected
programme
11
Main control features
This chapter describes how to set a large number of functions and combine them with each other using only a few control elements (1 control
knob and 4 buttons). This simple control method is made easy thanks to
the interactive display.
Interactive means that the washing machine display changes to reflect
each step you have entered. This ensures that only those settings that
make sense are made.
You are able to see the current settings at any time in the information
panel and in the symbol row.
We recommend that you take particular note of this chapter in order to
quickly familiarise yourself with the controls.
Switching the appliance on and off
3
Press the control knob to
switch the appliance on and
off.
When the appliance is
switched on the control
knob will pop up from its
flush position.
To turn off the appliance,
press the control knob back to its flush position.
To cancel any programme settings that were made previously, please
wait approx. 3 seconds after switching off the appliance before you
switch it on again.
Cancelling settings
If you would like to cancel settings that were accidentally made previously, switch off the appliance by pressing the control knob and after
approx. 3 seconds switch it back on. You are now able to make new settings.
12
Navigation display
The functions are detailed
over levels and pages within
the washing machine display.
Level 3 (Current level)
Level 2
Level 1
One level can include a
number of pages.
Current page
Total number pages
You can see from the navigation display which level
and page you are currently
on (here: level 3, page 1 of
2).
Control knob and pages
You can highlight the entries on the right of the display by turning the
control knob.
Turning the knob anti-clockwise moves the area highlighted down. If the area
highlighted is on the last entry of a page (here: WOOLLENS) and you then turn the
knob again in an anti-clockwise direction, the display
will turn to the next page (ö).
Turning the knob clockwise
moves the area highlighted
up. If the area highlighted is
on the first entry of a page
(here: SILK) and you continue to turn the knob in a
clockwise direction, the display will turn to the previous
page (î).
WOOLLENS 30°C
1200 RPM
10:17-10:54
î
START
30°
1200
OPTIONS
1200 RPM
START
1200
OPTIONS
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H)
SILK 30°C
10:17-10:53
ö
SILK H)
LINGERIE
40°-60° MIX
EASY IRON
REFRESH
13
Buttons and levels
Using the buttons you can:
– select the option that is
next to the button on the
right, e.g. START;
– change settings, e.g. temperature;
– change to another display
level, e.g. using the OPTIONS button.
1. Level: Programmes
î (1st level, page 1 of 3)
On this level you can:
– set the programme, temperature and spin speed;
– use the OPTIONS button to
change to the second level.
LINEN/EASY-C. 60°C
1400 RPM
60°
1400
OPTIONS
14
î
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
DELICATES 40°C
1200 RPM
START
40°
1200
OPTIONS
3
10:17-12:16
START
15:17-16:38
î
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
2. Level: OPTIONS
ç (2nd level, page 1 of 1)
On this level you can set varDELICATES 40°C
1200 RPM
15:17-16:38
ious additional functions.
ç
START
– Use the SELECT button to
TIME SAVING
directly set some of the
SELECT
DELAY START
options, e.g. STAIN.
STAIN)
BACK
PRE WASH
For other options (e.g.
EXTRAS
TIME SAVING) you change
to a sub-level where you
can select from many possibilities.
– You can return to the previous level by pressing the BACK button.
– Use the EXTRAS button to change to the third level.
You can set one or more options for each programme. When doing this
please note:
First set the programme (level 1), then the option (level 2).
3. Level: EXTRAS
ì (3rd level, page 1 of 2)
On this level you can set varEXTRAS
ious basic settings. These baì
sic settings will not be
cancelled when you switch
SELECT
MEMORY)
off the washing machine.
RINSE+
BACK
WATER COOLING
These basic settings will reGENTLE SPIN.
main active until they are
cancelled.
You will find more details about this in the “Extras” chapter.
Setting a programme: an example
DELICATES programme, 30 °C, 1,000 RPM spin, with STAIN option.
1. Press the control knob.
The appliance is now on.
The indicators in the display
are illuminated.
2. Use the control knob to
highlight the DELICATES
wash programme.
DELICATES 40°C
1200 RPM
40°
1200
OPTIONS
3. Press the wash temperature
button a number of times
until a temperature of 30°
appears.
î
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
DELICATES 30°C
1200 RPM
START
30°
1200
OPTIONS
4. Press the button for the spin
speed until a spin speed of
1,000 appears.
11:25-12:36
START
11:25-12:36
î
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
DELICATES 30°C
1000 RPM
START
30°
1000
OPTIONS
11:25-12:36
î
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
15
5. Press the OPTIONS button.
DELICATES 30°C
1000 RPM
11:25-12:36
î
START
30°
1000
OPTIONS
6. Use the control knob to
highlight the STAIN option.
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
DELICATES 30°C
1000 RPM
11:25-12:36
ç
START
SELECT
BACK
TIME SAVING
DELAY START
STAIN)
PRE WASH
EXTRAS
7. Press the SELECT button.
A tick will appear on the
right next to STAIN. The option has been activated.
F will appear in the symbol
row.
3
DELICATES 30°C
1000 RPM
START
SELECT
BACK
11:25-12:36
Fç
TIME SAVING
DELAY START
STAIN!)
PRE WASH
EXTRAS
Please refer to the chapter “Adding detergents and conditioners” and
“Loading the machine” before you start the wash programme.
8. If you want to start the proDELICATES 30°C
1000 RPM
11:25-12:36
gramme set in this example:
Fç
START
– Press the START button.
TIME SAVING
SELECT
The wash programme will
DELAY START
STAIN!)
start.
BACK
PRE WASH
EXTRAS
– If not, press the control
knob to switch off the appliance.
The indicators in the display will go out.
All of the settings described above have now
been cancelled.
16
DELICATES 30°C
1000 RPM
START
SELECT
BACK
EXTRAS
11:25-12:36
Fç
TIME SAVING
DELAY START
STAIN!)
PRE WASH
Overview of functions
Programmes (level 1)
Wash programmes
LINEN/EASY-CARE
Wash programme (20 °C to 60 °C) for cottons/
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
coloureds (cotton/linen), easy-care (mixed fabî
rics, e.g. cotton/polyester) and synthetics. The ap- START
LINEN/EASY-C.)
pliance adjusts the programme according to the 60°
ENERGY SAVING
different fabric types and load sizes. If the wash 1800
COTTONS
DELICATES
load is predominantly cotton/linen, the proWOOLLENS H
gramme is set for cottons/coloureds. If it consists OPTIONS
mainly of synthetics, the easy-care programme is
selected. If the load to be washed contains easy-care only, do not load
more than 2.5 kg in order to avoid excessive creasing of the laundry.
2
ENERGY SAVING
Special energy-saving and water-saving wash programme which washes at 60 °C for lightly to normally soiled cottons/coloureds (cotton/linen).
COTTONS
Wash programme which washes at 95 °C for cottons/coloureds (cotton/
linen).
DELICATES
Wash programme for delicates which washes at 30 °C or 40 °C.
WOOLLENS H (handwash)
Wash programme (COLD to 40 °C) for machine-washable wool and
handwashable wool fabrics with the H (handwash) care label.
3
SILK H (handwash)
Wash programme which washes at 30 °C for
handwashable and machine-washable silk.
1200 RPM
START
SILK 30°C
14:40-15:24
ö
As silk is a very delicate fabric we recommend
SILK H)
that, if possible, only one item of clothing be
LINGERIE
40°-60° MIX
washed at a time and that silk items are never
1200
EASY IRON
washed together with other rough-textured fab- OPTIONS
REFRESH
rics. For extremely delicate silk items the TIME
SAVING option can be used to ensure that the item is treated even
more gently.
17
LINGERIE
Gentle wash programme which washes at 40 °C for fine and delicate
fabrics. Important: Place padded lingerie in a washing net or bag.
40°-60° MIX
Programme for coloureds when various wash temperatures are indicated for the items to be washed. Various items which according to the
care labels are usually washed separately at 40 °C or 60 °C can be
washed together in the 40°-60° MIX programme. In this way the drum
capacity is better used and energy is saved as a result. Due to the extended wash time a wash result the same as that as for a normal 60°C
programme is achieved.
EASY IRON
Wash programme which washes at 40 °C for easy-care fabrics which
after being washed using this programme need to be ironed only lightly
or not at all.
REFRESH
An approx. 20-minute-long wash programme which washes at 30 °C
for quick washing of items such as lightly soiled sportswear that has
been worn only once.
FASHION
An especially gentle wash programme which
washes at 40 °C for modern fabrics such as viscose, modal, cupro, lyocell.
FASHION 40°C
1200 RPM
START
1200
OPTIONS
14:43-15:44
ú
FASHION)
SHORT SPIN
SPIN
STARCH
DRAIN
Special programmes
SHORT SPIN
Draining of water following a rinse hold and gentle spin, or separate
short spin of delicate items (delicates, woollens) with a low spin speed.
SPIN
Draining of water following a rinse hold and spin, or separate spinning
of handwashed cottons/coloureds and easy-care items.
18
STARCH
Separate starching, separate conditioning, separate impregnating of
damp washing (1 rinse cycle, liquid conditioner is rinsed in from the w
additive compartment, spin).
This programme setting can also be used to carry out a separate rinse
cycle. In this case, you do not need to add anything to the additives
compartment.
3
DRAIN
Draining of water following a rinse hold (without spinning).
Rinse hold means: The washing is left to soak in the final rinse water; it
is not spun.
Options (level 2)
Use the OPTIONS button to
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
switch to the second level.
î
START
Here you can select various
LINEN/EASY-C.)
additional functions for the
60°
ENERGY SAVING
previously selected wash
COTTONS
1800
DELICATES
programme, e.g. to adjust
OPTIONS
WOOLLENS H
the programme to the type
of fabric or degree to which
the items are soiled, or to set the start time and length of a wash programme. Only those options that are able to be combined with the selected wash programme will be displayed. The options will be removed
after the wash programme has ended.
TIME SAVING Z
Shortened wash programme
for lightly soiled items.
LINEN/EASY-C. 60°C
1800 RPM
START
SELECT
BACK
EXTRAS
If TIME SAVING has been set,
Z will appear in the symbol
row.
10:17-12:16
ç
TIME SAVING)
DELAY START
SENSITIVE
STAIN
PRE WASH
LINEN/EASY-C. 60°C
1800 RPM
START
SELECT
BACK
10:17-11:46
è
TIME SAVING§
NORMAL!
QUICK§(
VERY QUICK§
19
DELAY START
The DELAY START option allows the start of a wash programme to be
delayed. The DELAY START option can be set at 30-minute intervals. The
current time and the programme end time will be shown in the display
(e.g. 14:23 - 20:28).
SENSITIVE S
A special additional function with considerably more effective rinse
function (additional rinse cycle) an improved fabric care at the same
time (reduced drum movement). This is ideal when frequent washes are
necessary, for example in cases of highly sensitive skin. An additional
rinse cycle (RINSE+) is able to be selected in addition (see chapter “Extras”). If SENSITIVE has been set, S is displayed in the symbol row.
STAIN F
For heavily soiled or stained washing. (In-wash stain treatment products (salts or tablets) are drawn in at the optimum time during the programme.) If STAIN has been set, F is displayed in the symbol row.
PRE WASH V
A cold pre wash cycle prior to the main wash cycle, which follows automatically. If PRE WASH has been set, V is displyed in the symbol row.
Extras (level 3)
Use the EXTRAS button to
change to the third level.
Here you can select various
basic settings without affecting the particular wash
programme. These basic settings will remain active until
they are deselected.
LINEN/EASY-C. 60°C
1800 RPM
START
SELECT
BACK
EXTRAS
10:17-12:16
ç
TIME SAVING)
DELAY START
SENSITIVE
STAIN
PRE WASH
MEMORY
Programme settings that are frequently used can be saved (e.g. LINEN/
EASY-C., 40°C, 1200 RPM spin, with TIME SAVING).
There are four memory spaces available for this purpose. The saved programme setting will appear as an entry on the first programme page
(e.g. M1:LINEN/EASY-C.) and can be deselected as for a normal wash
programme. (See chapter “Memory: Saving a programme setting”.)
20
RINSE+ P
The washing machine is set
EXTRAS
such that its water conì
sumption is extremely economical. For people with
SELECT
MEMORY
allergies and in areas where
RINSE+)
BACK
WATER COOLING
the water is very soft, it can
GENTLE SPIN.
however be helpful to use
more water when rinsing.
When you select RINSE+ an additional rinse cycle will be carried out,
except for the WOOLLENS H, SILK H and LINGERIE programmes. If
RINSE+ has been selected, P will appear in the symbol row.
WATER COOLING
Before being drained at the end of the main wash cycle the wash water
is cooled by an inflow of cold water in order to prevent the plastic drain
pipes from sustaining thermal damage. This basic setting only takes effect with the COTTONS, LINEN/EASY-C. and ENERGY SAVING programmes.
GENTLE SPIN
Adjustable spin cycle, integrated with the final spin cycle. The washing
does not cling to the side of the drum as much and can be removed
more easily.
LANGUAGE
To set the language in which the indicators are to appear in the display.
(See chapter “Changing the language”.)
TIMER
To set the current time. This is important as it enables the end of the
wash programme to be shown in the display and the DELAY START additional function to be used. (See the chapter “Before washing for the
first time: Setting the timer”.)
VOLUME
You will hear an acoustic signal when you press the buttons. The volume of this signal can be regulated and/or the signal can be switched
off. The volume of the alarm for error messages cannot be altered.
21
Preparing a Wash Load
Sorting and preparing a wash load
• Sort the washing according to care symbol (see “Washing Types and
Care Symbols”).
• Empty all pockets.
• Remove metal objects (paper clips, safety pins etc.).
• In order to prevent the washing tangling and being damaged: close
zippers, button up duvet covers and pillow cases, and tie up loose
straps such as from aprons.
• Turn articles with double layered fabric inside out (sleeping bags,
anoraks etc.).
• In the case of knitted coloured fabrics and also wool and fabrics with
jewellery attached: turn inside out.
• Place small and delicate articles (baby booties, stockings, bras etc.)
into a washing net, a pillow case with zipper, or in large socks before
washing.
• Handle curtains with particular care. Metal fittings or burred, plastic
fittings must be removed or tied into a net or bag. We cannot accept
liability for damage.
• Do not wash coloured and white washing together. This could transfer colour to white washing or turn it grey.
• New coloured items often have an excess of colour. It is better to
wash such items separately the first time.
• Mix small and large items of washing. This improves the wash efficiency and the washing is more evenly distributed during the spin cycle.
• Shake out washing before placing into the washing machine.
• Do not place folded washing into the drum.
• Observe such washing instructions as “wash separately” and “wash
separately several times”!
22
Types of washing and care symbols
Care symbols help you to choose the correct wash programme. Washing
should be sorted by type and according to care symbols. The temperatures indicated on the care symbols are the maximum wash temperatures.
Cottons O
Cotton and linen items with this care symbol are not sensitive to machine washing or high temperatures. The COTTONS programme is suitable for such items.
Coloureds M J
Cotton and linen items with this care symbol are not sensitive to machine washing. The LINEN/EASY-C. programme is suitable for such
items.
Easy-care items N K
Materials such as fine cotton, cotton-blend fabrics and synthetics with
these care symbols require a gentler machine wash. The LINEN/EASY-C.
and EASY IRON programmes are provided for use with such items.
Delicates L
Materials such as layered fibres, micro-fibres, synthetics and curtains
with this care symbol require careful handling. The DELICATES programme is suitable for such items.
Viscose K L
Modern materials such as viscose, cupro, lyocell, modal etc. require especially careful handling. The FASHION programme is suitable for such
items.
Lingerie K L
The LINGERIE programme is suitable for fine and delicate items made of
polyester, polyamide and mixed fabrics with these care symbols.
Wool, silk and especially delicate items W L H
Fabrics such as wool, wool blends and silk with these care symbols are
particularly sensitive to machine washing. The WOOLLENS H and
SILK H programmes are suitable for such items.
Important: Items with care symbols G (Do not wash!) must not be
washed in washing machines.
23
Washing Detergents and Care Agents
Which washing detergent and care agent?
Use only washing detergents and care agents which are suitable for use
in washing machines. Always follow the manufacturer's instructions.
How much washing detergent and care agent?
2
The amount to be used depends on:
• the dirtiness of the washing
• the hardness category of the mains water supply
• the filling quantity
If the detergent manufacturer gives no details of the dosing quantities
for minimum loads, add one third less for half loads and, in the case of
very small loads and for EASY IRON, only half the amount of detergent
recommended for a full load.
Refer to the detergent/care agent manufacturer's instructions on use
and dosage.
Water softener
2
For medium to high water hardness (hardness class II upwards), you
should use softener. Refer to the manufacturer's instructions. Then always add the appropriate amount of detergent for hardness class I
(= soft). The responisable water works will provide information on the
local water hardness.
Since the water softener is rinsed in before the main detergent (water
pre-softening), 80% of the stated quantity of softener shown on the
package is sufficient.
Water hardness details
Water hardness in °dH
(German hardness scale)
Water hardness in mmol
(millimol per litre)
I - soft
0-7
to 1.3
II - medium hard
7 - 14
1.3 - 2.5
III - hard
14 - 21
2.5 - 3.8
greater than 21
greater than 3.8
Hardness class
IV - very hard
24
Before the first wash
Setting the time
You should set the time prior to the first wash and when changing to
and from daylight savings time.
1. Press the control knob.
The appliance is switched on.
2. Press the OPTIONS button.
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
î
START
60°
1800
OPTIONS
3. Press the EXTRAS button.
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
ç
START
SELECT
BACK
EXTRAS
4. Turn the knob to TIMER.
5. Press the SELECT button.
TIME SAVING)
DELAY START
SENSITIVE
STAIN
PRE WASH
EXTRAS
ô
SELECT
LANGUAGE
TIMER)
VOLUME
BACK
6. Use the control knob to set
the current time.
7. Press the SELECT button to
save the set time.
8. Press the BACK button three
times.
You are now on the first level
and can select a wash programme.
EXTRAS
é
SELECT
BACK
TIMER
15:11 H:MIN)
25
Carrying out a wash programme prior to first use
Prior to washing your first load, carry out a wash cycle without washing (LINEN/EASY-C. 60°, with half the amount of detergent).
This will remove residues remaining as a result of the production process from the drum and water container.
1. Press the control knob.
The appliance is switched on.
2. Place the detergent in the
left compartment of the detergent drawer.
3. Press the START button.
The wash programme will
start.
LINEN/EASY-C. 60°C
1800 RPM
START
60°
1800
OPTIONS
26
10:17-12:16
î
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
Performing a wash cycle
Opening and closing the door
3
• To open: pull the handle on the door.
• To close: firmly push the door shut
If the O symbol is showing in the display, the door can be opened.
If the N symbol is showing in the display, the door is blocked.
If the error message PLEASE CLOSE THE DOOR is showing in the display,
you have attempted to start a wash programme without having correctly shut the door. Should this happen, firmly press the door shut and
restart the wash programme.
Loading the washing
3
For instructions on how to correctly prepare washing, see the “Sorting
and preparing the washing”.
1. Sort and prepare the washing according to type.
2. Open the door: pull the handle on the door.
3. Load the washing.
Important: When shutting the
door, be sure that no items are
caught in it. This could result in
damage to both machine and
clothes.
4. Close the door firmly.
27
Adding detergents/conditioners
3
For instructions on the use of detergents and conditioners, please see
the section “Detergents and conditioners”.
1. Open the detergent drawer: close
your fingers around the flap at
the bottom of the drawer (1); pull
out the drawer as far as it will go
(2).
2. Adding detergent/conditioner
Compartment for detergent in
Detergent in powder form/tablets
powder form/tablets to be used
to be used for main wash
for main wash (left):
Stain removal agent/
stain removal tablets
If you are using water softener and
require the right-hand compartment for the detergent for the pre
wash, place the water softener in
the left-hand compartment on top
of the detergent for the main wash.
Compartment for stain removal
agent/stain removal tablets
(centre rear):
Only add stain removal agent if the
STAIN option has been selected.
Compartment for water softener
or for detergent for pre wash
Liquid conditioner
(right):
Water softener
Only add detergent for a pre wash if
or detergent for pre wash
the PRE WASH option has been selected.
Compartment for liquid conditioners (centre front):
Softener, stiffener, starch
Important: Fill the compartment to no more than the MAX indicator.
Viscous liquid can be diluted up to the MAX indicator; dissolve starch in
powder form.
Note: It is normal for a small amount of water to remain in the compartment for liquid conditioner, and this does not detract from the final rinse result.
3. Push the detergent drawer in fully.
28
3
If using liquid detergents/tablets:
Add the liquid detergent or tablets using the measuring container provided by the detergent manufacturer. Follow the instructions on the
detergent packaging.
Setting a wash programme
1. Press the control knob.
The appliance is now
switched on.
2. Use the control knob to
highlight the desired wash
programme, e.g. DELICATES.
DELICATES 40°C
1000 RPM
40°
1200
OPTIONS
3. Press the button for the
wash temperature and continue pressing it until the
desired temperature appears
(e.g. 30°).
î
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
DELICATES 30°C
1200 RPM
11:25-12:36
î
START
30°
1200
OPTIONS
4. Press the button for the spin
speed and continue pressing
it until the desired spin
speed (e.g. 1,000) or the
RINSE HOLD indicator appears.
11:25-12:36
START
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
DELICATES 30°C
1000 RPM
START
30°
1000
OPTIONS
11:25-12:36
î
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
.
5. If you do not wish to make
DELICATES 30°C
1000 RPM
11:25-12:36
any further settings, press
î
START
the START button.
LINEN/EASY-C.
30°
The wash programme will
ENERGY SAVING
COTTONS
start. (See the chapter
1000
DELICATES)
“Starting a wash proOPTIONS
WOOLLENS H
gramme”.)
If you would like to select
options, see the chapter “Setting options”.
29
Set the options, e.g. DELAY START
This option allows the start time for a wash programme to be delayed
from 30 minutes to a maximum of 23.5 hours.
1. Press the OPTIONS button.
DELICATES 30°C
1000 RPM
11:25-12:36
î
START
30°
1000
OPTIONS
2. Use the control knob to
highlight the DELAY START
option.
3. Press the SELECT button.
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
DELICATES 30°C
1000 RPM
11:25-12:36
ç
START
SELECT
BACK
TIME SAVING
DELAY START(
STAIN
PRE WASH
EXTRAS
3
3
4. Use the control knob to set
the time at which you want
the wash programme to end.
DELICATES 30°C
1000 RPM
è
SELECT
END OF PROGRAMME
The DELAY START option can
14:06 H:MIN(
BACK
be set at 30-minute intervals.
5. Press the SELECT button.
The programme end time will change in the information panel
(e.g. 14:06).
6. Press the START button.
While DELAY START is counting down, the washing machine is switched
into stand-by mode. The background illumination of the display will go
out.
Cancelling DELAY START:
• Press the START button.
The wash programme will
start immediately.
DELICATES 30°C
1000 RPM
START
11:25-14:06
N§
DELAY START
1000
UNLOCK DOOR
30
11:25-14:06
START
[==##############
Starting a wash programme
3
1. Check that the water tap is open.
2. After you have set the wash
programme and any options,
press the START button.
The wash programme will
start.
DELICATES 30°C
1000 RPM
11:25-12:36
è
START
BACK
1000
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES)
WOOLLENS H
EXTRAS
Approx. 30 seconds after the
washing machine is switched
on or after a button or the control knob was last actuated, the START
indicator will begin to flash. If you do not wish to make any further
settings, press the START button.
If a delayed start has been set:
If the DELAY START option has been selected, the wash programme will
finish at the time shown in the display. If the wash programme has not
yet been started, you can still cancel the delay start. The wash programme will start immediately. (See chapter “Setting options, e.g.
DELAY START”.)
If you would like to add washing even after the programme has started.
1. Press the UNLOCK DOOR
DELICATES 30°C
1000 RPM
11:25-14:36
button. The O symbol will
N§
START
appear.
DELAY START
2. Open the door.
[==##############
1000
Add the items.
UNLOCK DOOR
3. Then close the door and
press the LOCK DOOR button.
DELICATES 30°C
1000 RPM
START
11:25-14:36
O§
DELAY START
[==##############
1000
LOCK DOOR
31
Wash programme progress
Each current stage of the
programme is shown in the
display during the wash programme, e.g. main wash, and
a bar showing the programme progress.
The N symbol is displayed as
the programme progresses:
the loading door is locked.
DELICATES 30°C
1000 RPM
PAUSE
11:25-12:36
N§
MAIN WASH
#####=========]
1000
MOISTURE 49 %
Moisture/Loading
During the wash programme
LINEN/EASY-C. 60°C
1400 RPM
11:25-12:36
the display additionally indiN§
PAUSE
cates:
MAIN
WASH
– the expected residual
#####=========]
moisture in the washing at
LOADING 80 %
1400
MOISTURE 50 %
the end of the programme.
The value depends on the
selected spin speed.
– the loading of the drum (in 10 per cent steps.)
This value is indicated with the LINEN/EASY-CARES and COTTONS
programme only. The loading can be estimated by the washing machine about fifteen minutes into the programme.
Changing the spin speed
The spin speed can still be changed and rinse hold still be set during the
programme. Other settings cannot be changed.
3
32
Cancelling the programme
To cancel the programme before it has finished, switch off the appliance (press the control knob).
The wash programme can be interrupted at any time by pressing the
PAUSE button.
When the wash programme is complete
3
3
When a wash programme is complete, PLEASE TAKE OUT THE CLOTHES
will appear in the display.
If you do not press any buttons or press the control knob within three
minutes of the programme finishing, the washing machine will switch
into standby mode. The stand-by mode is cancelled by pressing one of
the buttons or turning the knob.
If EASY IRON has been selected, a crease prevention cycle of approx. 30
minutes takes place after the programme has ended. You can remove
the washing at any time during the crease prevention cycle. To do this,
press the PAUSE button and the door can be opened.
For rinse hold
If the wash cycle was ended with a rinse hold, the water must first be
drained and if necessary the washing spun:
Spin:
1. Set the desired spin speed.
DELICATES 30°C
RINSE HOLD
11:25-11:28
N§
START
RINSE HOLD
###############
RINSE H.
MOISTURE 97 %
2. Press the START button.
The washing will be spun.
DELICATES 30°C
1000 RPM
11:25-11:28
N§
START
RINSE HOLD
###############
1000
MOISTURE 97 %
Short spin or drain:
1. Switch the appliance off and
then on again.
2. Using the control knob,
either
– highlight SHORT SPIN
(reduce spin speed if required) or
– highlight DRAIN.
SHORT SPIN
800 RPM
START
800
OPTIONS
11:25-11:28
ú
FASHION
SHORT SPIN)
SPIN
STARCH
DRAIN
33
3. Press the START button.
– If short spin is selected the water will be drained and the washing
gently spun.
– If drain is selected the water will be drained (without being spun).
Unloading the washing
If the O§symbol is shown in
END
the display, the door can be
O§
opened.
PLEASE TAKE OUT THE CLOTHES
1. Open the door using the
###############
handle.
MOISTURE 32 %
2. Remove the washing.
3. Press the control knob.
The appliance is now switched off.
Important: If the washing machine will not be used for a longer period
of time:
Turn off the tap and remove the plug from the mains. (The Aqua Control water protection system does not function without an electricity
supply.)
OVERDOSING indicator
If OVERDOSING is shown in
END
the display at the end of a
O§
wash cycle, too much deterPLEASE
TAKE
OUT
THE
CLOTHES
gent was used in the com###############
pleted wash programme.
MOISTURE 32 %
Please take note of the dosOVERDOSING
age instructions provided by
the detergent manufacturer
and the amount of washing loaded the next time you wash.
34
MEMORY
Saving a programme setting
3
The MEMORY basic setting can be used to save frequently-used programme combinations (wash programme, temperature, spin speed and
option/s). There are four memory cells available for this purpose. The
saved programme can then be selected in the same way as any other
wash programme.
Extras cannot be saved using MEMORY. They must be set separately and
remain active until they are cancelled.
Example: LINEN/EASY-C., 40 °C, 1200 RPM spin, with SENSITIVE option.
1. Press the control knob.
The appliance is now on.
2. Turn the knob to the LINEN/
EASY-C. prgramme.
3. Set the temperature and spin
speed using the relevant
buttons.
4. Press the OPTIONS button.
5. Use the control knob to
highlight the SENSITIVE option.
6. Press the SELECT button.
The S symbol will appear in
the display.
7. Press the EXTRAS button.
LINEN/EASY-C. 40°C
1200 RPM
START
40°
1200
OPTIONS
10:17-12:16
î
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
LINEN/EASY-C. 40°C
1200 RPM
START
SELECT
BACK
EXTRAS
10:17-12:16
ç
TIME SAVING
DELAY START
SENSITIVE)
STAIN
PRE WASH
LINEN/EASY-C. 40°C
1200 RPM
START
SELECT
BACK
EXTRAS
10:17-12:16
Sç
TIME SAVING
DELAY START
SENSITIVE!)
STAIN
PRE WASH
35
If MEMORY is highlighted:
8. Press the SELECT button.
EXTRAS
ì
SELECT
MEMORY(
RINSE+
WATER COOLING
GENTLE SPIN.
BACK
If MEMORY 1 is highlighted:
9. Press the SAVE button.
The programme setting has
now been saved.
MEMORY
LINEN/EASY-C. 40°C
é
SAVE
MEMORY 1(
MEMORY 2
MEMORY 3
MEMORY 4
BACK
10. Press the BACK button three
times. You are now on the
first level again.
MEMORY
LINEN/EASY-C. 40°C
BACK
36
1200
é
SAVE
3
1200
MEMORY 1!(
MEMORY 2§§
MEMORY 3§§
MEMORY 4§§
The saved programme setLINEN/EASY-C. 40°C
1200 RPM
10:17-12:16
ting will appear as the first
Sþ
START
entry on the first page (e.g.
M1:LINEN/EASY-C.)
40°
M1: LINEN/EASY-C. 40°C,
LINEN/EASY-C.
ENERGY SAVING
1200
with 1,200 RPM spin and
COTTONS
SENSITIVE/S option). The
OPTIONS
DELICATES
saved programme setting
can then be selected in the same way as any other wash programme.
After this new entry the first level now includes a total of four pages.
The navigation symbol will change to þ.
Cancelling a saved programme setting
1. Press the OPTIONS button.
LINEN/EASY-C. 40°C
1200 RPM
10:17-12:16
Sþ
START
40°
1200
OPTIONS
2. Press the EXTRAS button.
M1:LINEN/EASY-C.)
LINEN/EASY-C.
ENERGY SAVING
COTTONS
DELICATES
LINEN/EASY-C. 40°C
1200 RPM
10:17-12:16
ç
START
SELECT
BACK
EXTRAS
If MEMORY is highlighted:
3. Press the SELECT button.
EXTRAS
ì
SELECT
BACK
4. Use the control knob to
highlight MEMORY 1.
5. Press the CLEAR button.
The saved programme has
now been cancelled.
Then press the BACK button
three times.
You are now on the first level again.
TIME SAVING)
DELAY START
SENSITIVE
STAIN
PRE WASH
MEMORY(
RINSE+
WATER COOLING
GENTLE SPIN
EXTRAS
é
CLEAR
BACK
MEMORY 1!(
MEMORY 2§§
MEMORY 3§§
MEMORY 4§§
37
Changing the language
You can change the language setting if you would like the indicators in
the display to appear in a different language.
1. Press the control knob.
The appliance is switched on.
2. Press the OPTIONS button.
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
î
START
60°
1800
OPTIONS
3. Press the EXTRAS button.
LINEN/EASY-C.)
ENERGY SAVING
COTTONS
DELICATES
WOOLLENS H
LINEN/EASY-C. 60°C
1800 RPM
10:17-12:16
ç
START
SELECT
BACK
EXTRAS
4. Use the control knob to
highlight LANGUAGE.
TIME SAVING)
DELAY START
SENSITIVE
STAIN
PRE WASH
EXTRAS
ô
SELECT
LANGUAGE)
TIMER
VOLUME
BACK
5. Press the SELECT button.
EXTRAS
ô
SELECT
BACK
38
LANGUAGE)
TIMER
VOLUME
6. Use the control knob to
highlight the desired language, e.g. English.
As soon as the language is
highlighted, the indicators in
the display will change to
this language.
7. Use the SELECT button to
save the selected language.
All indicators in the display
will immediately appear in
this language.
EXTRAS
LANGUAGE
Í
§
SELECT
ENGLISH)
DEUTSCH§
ITALIANO§
FRANÇAIS§
BACK
EXTRAS
LANGUAGE
Í
§
SELECT
BACK
ENGLISH!)
DEUTSCH§§
ITALIANO§§
FRANÇAIS§§
39
Cleaning and Care
Control panel
Important! Do not use any furniture cleaning agents or aggressive
cleaning agents in order to clean panel and control parts.
Wipe control panels with a damp cloth. When doing so, use warm water.
Detergent Drawer
The detergent drawer should be cleaned from time to time.
1. Pull the detergent drawer out as far as it will go.
2. Remove the detergent drawer by pulling sharply.
3. Take the conditioner insert out of
the middle compartment.
4. Clean the conditioner insert under
running water.
5. Clean the compartments with
warm water from the rear side. It is
best to use a flat brush.
6. Push on the conditioner insert as
far as it will go so that it is securely
in place.
40
7. Use a brush to clean the entire
rinsing-in section of the washing
machine, particularly also the nozzles on the top side of the rinsingin chamber.
8. Set the detergent drawer into the
guide tracks and push in.
Washing Drum
The washing drum is made of stainless steel. Rusting foreign bodies in
the washing can cause rust deposits on the drum.
Important! Do not clean the stainless steel drum with decalcifying
agents containing acids, scouring agents containing chlorine or iron, or
steel wool. Our Customer Service can provide suitable agents.
Remove any rust deposits on the drum using a stainless steel cleaning
agent.
Main door
Check on a regular basis to see if deposits or foreign objects are present
in or at the rubber sleeve behind the door, and remove.
41
What to do if...
Remedying a malfunction
In the event of a malfunction, try to rectify the problem yourself with
the aid of the instructions provided here. If you request a visit from
customer service to remedy one of the malfunctions listed here, or to
rectify an error made when using the appliance, the customer service
engineer’s visit will not be free of charge, even during the warranty period.
• If any of the following error messages are shown in the display, you
may be able to rectify the malfunction yourself:
– ATTENTION / PLEASE CLOSE THE DOOR
– ATTENTION CD1 / PLEASE OPEN THE TAP
– ATTENTION CD2 / PLEASE CHECK THE WATER DRAINAGE
(To remedy the error, see the following malfunction chart.)
After you have rectified the error, press the START button. If the error
code is displayed again, please contact customer service.
• If ATTENTION / PLEASE
ATTENTION
Cd6
CALL YOUR LOCAL SERVICE
FORCE and an error code
PNC: xxx xxx xxx
(e.g. CD6) is shown in the
display, please proceed as
PLEASE CALL YOUR LOCAL
SERVICE FORCE|
follows:
– Switch off the appliance
and switch it on again
after approx. 3 seconds;
– Reset the wash programme again;
– Press the START button.
If the error code is displayed again, please contact customer service. In
such an event, please provide the error code shown in the display and
the PNC no. shown.
Problem
The washing machine
does not work.
42
Possible cause
Remedy
The power plug is not
connected.
Connect the plug to a power
outlet.
A domestic fuse has tripped.
Replace the fuse.
The START button has not
been pressed.
Press the START button.
Problem
Possible cause
Remedy
The wash programme
will not begin after the
START button was
The door is not closed proppressed. ATTENTION /
erly.
PLEASE CLOSE THE
DOOR is showing in the
display.
Close the door - there should
be an audible click. Press the
START button.
The door cannot be
closed.
The child safety device is
engaged.
Disengage the child safety
device (see section “Child
safety device”).
The transport locks have not
been removed.
Remove the transport locks
as described in the
installation and connection
instructions.
The height-adjustable feet
have not been set correctly.
Adjust the feet as described
in the installation and connection instructions.
The washing machine
vibrates when operating or is not stable.
There is very little washing in
Operation is not affected by
the drum (e.g. only one baththis.
robe).
Water was not able to be
drained completely before
spinning, because
the outlet hose has a kink in
it or
the drain pump is clogged.
The main water for the
Too much detergent was
main wash is producing
probably used.
too many suds.
Check the positioning of the
outlet hose and even out any
kinks if necessary or clean
the drain pump and remove
any foreign matter that may
be in the pump housing.
Follow the manufacturer's
instructions exactly when
measuring out detergent.
43
Problem
Water is running out
from under the washing machine.
Possible cause
Remedy
The threaded inlet hose fitting is leaking.
Screw the inlet hose in
firmly.
The outlet hose is leaking.
Check the outlet hose and
replace if necessary.
The drain pump cover is not
closed properly.
Close the cover properly.
Cancel the programme and
Washing has been trapped in
free the washing from the
the door.
door. Restart the programme.
Close the emergency emptying hose properly (see section “Carrying out an
The emergency emptying
hose is not closed properly or emergency emptying procedure”). If the emergency
is leaking.
emptying hose is leaking, call
Service Force.
Conditioner is not being rinsed in, and the
w compartment for
additives is full of water.
The conditioner insert is not
correctly set into the additive compartment or is
clogged.
The washing is badly
creased.
Observe maximum load sizes
(see chapter “Consumption
Too much washing was probvalues and load sizes”). Select
ably loaded.
the EASY IRON programme
for easy-care items.
The washing has not
been spun as dry as
usual.
Always load the drum as full
The washing was not able to
as possible with a
be distributed evenly in the
combination of large and
drum prior to spinning.
small items.
The door cannot be
opened when the
washing machine is
switched on. The N
symbol is showing in
the display.
44
Clean the detergent drawer,
insert the conditioner insert
firmly.
The door is looked for reasons related to safety.
Wait until the O symbol
appears.
The washing machine is in
stand-by mode.
Press any button.
Problem
Possible cause
Remedy
As soon as the power failure
is over the wash programme
will continue.
The display goes out
while a wash programme is running.
Detergent residues are
accumulating in the
detergent drawer.
The rinse water is
cloudy.
A power failure has occurred.
For reasons related to safety,
the filling door will remain
locked for approx. 4 minutes.
The tap is not fully open.
Turn the tap on fully.
The filter in the threaded inlet hose fitting is clogged at
the tap or at the washing
machine.
Close the tap. Unscrew the
inlet hose from the tap and
from the machine. Clean the
filter.
The probable cause is a detergent with a high silicate
content.
No negative impact on the
rinse result; try using a liquid
detergent.
The background illumination of the display
The washing machine is in
has gone out even
stand-by mode.
though the appliance is
switched on.
The tap is closed.
Water is not entering
the appliance. ATTEN- The filter in the threaded inlet hose fitting is clogged.
TION CD 1 / PLEASE
OPEN THE TAP is showing in the display.
The tap is furred with limescale or faulty.
The washing machine
drain pump runs continuously - even when
the appliance is
switched off.
If you wish to remove the
washing: If water is visible in
the viewing window, first
carry out an emergency
emptying procedure (see section “Carrying out an emergency emptying procedure”).
After approx. 4 minutes the
door can be opened.
The Aqua Control anti-flood
system is in operation.
Press any of the buttons.
Open the tap.
Close the tap. Unscrew the
hose from the tap, take out
the filter and wash it under
running water.
Check the tap and have it repaired if necessary.
Close the tap, remove the
mains plug from the socket
and contact Service Force.
45
Problem
The washing has not
been spun thoroughly
and water remains visible in the drum.
ATTENTION CD 2 /
PLEASE CHECK THE
WATER DRAINAGE is
showing in the display.
46
Possible cause
Remedy
The outlet hose is kinked.
Straighten the hose.
The maximum pump height
(outlet height 1m from the
washing machine’s installation surface) has been
exceeded.
Contact Service Force, who
will be able to provide an
adaptor kit for pump lifts
greater than 1m as a special
accessory.
The drain pump is clogged.
Switch off the machine and
disconnect the mains plug;
clean the drain pump.
For siphon connections: The
siphon is blocked.
Clean the siphon.
If the washing results are not satisfactory
If the washing has turned grey and if limescale is deposited in the
drum, then
• Too little detergent was used.
• The wrong detergent was used.
• Special soiling was not pre-treated.
• Program or temperature not set correctly.
• If multi-component detergents are used, the individual components
were not used in the correct ratio.
If there are still grey spots on the washing,
• Washing soiled with ointments, grease or oils was washed with too
little detergent.
• Too lower temperature was used for washing.
• A frequent cause is that softener - particularly that in concentrated
form - has reached the washing. Wash out such spots quickly and use
the softener concerned carefully.
If at the end of the last rinse foam is still visible
• Modern detergents can also cause foam in the last rinse. However,
the washing is still sufficiently rinsed.
If there are white remnants on the washing
• These are insoluble components of modern detergents. They are not
the result of an insufficient rinsing effect.
Shake or brush out the washing. In future, perhaps you should turn
the washing inside out before washing it. Examine your choice of detergent and if necessary use liquid detergent.
47
Carrying out emergency drainage
1
• If the washing machine no longer pumps off the washing solution,
emergency drainage must be performed.
• If the washing machine is in a room where there is a risk of frost,
emergency drainage must be performed if there is a possibility of
frost.
In addition: unscrew the inlet hose form the water tap and place it on
the floor. Empty the drainage hose.
Warning! Switch off the washing machine before performing emergency drainage and pull out the mains plug.
Caution! The washing solution escaping from the emergency drainage
hose may be hot. There is a risk of scalding! Allow the washing solution
to cool down before performing emergency drainage.
1. Place a flat collecting vessel in order to collect the washing solution
which is draining off.
2. Fold open the flap in the right section of the base outwards and pull it
off.
3. Remove the emergency drainage
hose from its holder.
4. Place the container under the hose.
5. Detach the plug of the emergency
drainage hose by turning it anticlockwise and pull it out.
The washing solution runs out. Depending on the amount of solution,
it may be necessary to empty the
collecting vessel several times. To do
this, close the emergency drainage
hose temporarily with the plug.
48
When the water is completely drained:
6. Push the plug securely into the emergency drainage hose and turn it
clockwise to secure it.
7. Replace the emergency drainage hose in its holder.
8. Put on the flap and close.
Drain pump
The drain pump is maintenance free. The cover of the drain pump must
only be opened in the event of a malfunction when no more water is
being pumped out, e.g. if the pump is blocked.
Before loading the machine, please always ensure that there are no foreign objects left in the pockets or in between the items to be washed.
Paper clips, nails etc. which may find their way into the washing machine along with the washing will remain in the drain pump housing.
1
To restart the drain pump when it is blocked, please proceed as follows:
Warning! Switch off the washing machine and remove the mains plug
before cleaning the drain pump!
1. First carry out an emergency emptying procedure (see section “Carrying
out emergency drainage”).
2. Place a cloth on the floor in front of the cover of the drain pump. Residual water may run out.
3. Unscrew the drain pump cover in
an anti-clockwise direction and
pull it out.
4. Remove any foreign objects and
fabric lint from the pump housing.
49
5. Replace the pump cover. Laterally
insert the webs on the cover into
the guide slots and screw on the
cover in a clockwise direction.
6. Close the emergency emptying
hose and place it in the holder.
7. Close the flap.
Anti-flood system Aqua Control +
Aqua Alarm
In the event of damage to the supply hose, the system blocks the further supply of water to the unit directly st the water tap.
If water escapes at another point, the drainage pump pumps the water
off automatically - even if the unit is switched on. It is merely necessary for the washing machine to be connected to the mains. If the antiflood system responds, a warning signal sounds at the same time.
What does “UPDATE” mean?
The wash programmes in your washing machine are controlled by software.
New types of fabric or new detergents may require new wash programmes in the future. In most cases, the software can be adapted to
this.
For further information on a possible “update” please contact customer
service.
50
Child Safety Feature
If the child safety feature is set,
the filling door can no longer be
closed and no washing program
can be started
Setting the child safety feature
Use a coin to turn the rotary knob
on the inside of the filling door
clockwise as far as it will go.
1
Warning! The rotary knob must
not be in a vertical position after
adjustment, otherwise the child
safety feature is not active. The rotary knob must project as shown in
the diagram.
Cancelling the child safety
feature
Turn the rotary knob anticlockwise
as far as it will go.
51
Consumption values and load sizes
Consumption values
The values for selected programmes provided in the following table
were determined under normal conditions. As well as being dependent
on the settings selected (additional functions), the consumption values
are also dependent on external factors such as water temperature or
detergent used. Nonetheless, they serve as a helpful guide for normal
household use.
Wash programme/
Temperature
Type of fabric
Water
in litres
Energy
in kWh
ENERGY SAVING1)
Cotton
37
0,85
COTTONS 95
Cotton
42
1,80
LINEN/EASY-C. 60
Cotton
42
0,95
LINEN/EASY-C. 40
Cotton
49
0,55
LINEN/EASY-C. 60
TIME SAVING (QUICK1)
Synthetics
48
0,70
LINEN/EASY-C. 40
TIME SAVING (QUICK)1)
Synthetics
48
0,50
LINEN/EASY-C. 40
TIME SAVING (VERY QUICK)
Synthetics
42
0,50
DELICATES 30
Synthetics
54
0,35
Wool
42
0,16
WOOLLENS H 30
1) For your information: Programme setting for testing in accordance with or supporting EN 60 456 and IEC 60 456.
52
Load sizes
Type of fabric
Load size in kg1)
LINEN/EASY-C.
Cotton
5
LINEN/EASY-C.
Synthetics
2,5
ENERGY SAVING
Cotton
5
COTTONS
Cotton
5
DELICATES
Synthetics
2,5
Wool
2
Silk
1
Synthetics
1
40°-60° MIX
Cotton
5
EASY IRON
Synthetics/Cotton
1
REFRESH
Synthetics/Cotton
2,5
FASHION
Viscose
2,5
Wash programme
WOOLLENS H
SILK H
LINGERIE
1) The load size is determined in accordance with EN 60 456 standard load.
53
Installation and connection instructions
Installation Safety Precautions
• Do not tilt the washing machine onto its front or onto its right side
(viewed from the front). Electronic components can get wet.
• Check the washing machine for transport damages. A damaged unit
must never be put into operation under any circumstances. In the
event of damage, please contact your supplier.
• Ensure that all parts of the transport safeguard are removed and that
the unit is splash protected, see "Removing transport safeguard".
Otherwise, the units or neighbouring furniture can be damaged when
spinning.
• Always insert the plug into a correctly installed earthed socket.
• In the case of permanent connection: A permanent connection may
only be made by an authorised specialist.
• Before putting the machine into operation, ensure that the mains
voltage and current type shown on the unit's rating plate correspond
with those at the place where the machine is being installed. The fuse
rating is also found on the rating plate.
• Should work be carried out on the water supply installations in order
to allow the machine to be connected properly to the water supply,
this work must be carried out by an authorised installer.
• Should work be carried out on the mains supply in order to allow the
machine to be connected properly to the electricity supply, this work
must be carried out by an authorised electrician.
• The mains lead may only be replaced by the customer service or by an
authorised electrician.
54
Installation of the appliance
3
Washing machines with curved panels are not suitable for installing
under units.
Transporting the appliance
• Do not place the washing machine on its front or on its right side
(viewed from the front). Otherwise, electrical components can get
wet.
• Never transport the unit without the transport safeguard. Do not remove the transport safeguard until the appliance is at the installation
location. Transporting the unit without the transport safeguard can
damage it.
• Lift the appliance neither by an open filling door nor by the base.
When transporting the unit with a sack trolley:
• Attach the sack trolley only at the side. The sack trolley shovel must
not be longer than 24 cm, otherwise the float switch can be destroyed.
Remove transport packaging
Important! It is essential to remove the transport packaging before putting the appliance into
operation. Keep all parts of the
transport packaging in a safe
place for future use.
1. Open both hose holders on the
appliance's rear side and remove
the hoses and mains cable.
55
3
2. Pull both hose holders off the appliance with a strong pull.
The special spanner (A) and the
caps (B) (2 each) and (C) (1 each)
are supplied with it.
3. Remove the screw D, including
the compression spring with the
special spanner A.
4. Cover the hole with the cap C.
Important! When fitting the
plastic caps, press until they snap
into the rear panel securely.
5. Remove the two screws (E) with
the special spanner (A).
6. Remove the 4 screws (F).
7. Remove the transit bar (G).
8. Screw the 4 screws (F) back in for
safe keeping.
9. Close the 2 large holes with the
caps (B).
Important! When fitting the
plastic caps, press until they snap
into the rear panel securely.
56
Prepare the installation place
• The installation surface must be clean and dry, free of floor polish
residues and other greasy coatings so that the unit does not slip
away. Do not use lubricants as a sliding aid.
• Installation on a high-veil carpet or floor tiles with soft sponge backs
is not recommended because the standing safety of the appliance is
then no longer ensured.
• By installation surfaces with small-format tiles, lay a conventional
rubber mat underneath.
• Minor unevenness of the floor surface should never be levelled out by
laying pieces of wood, card or similar materials, but rather should always be compensated for by adjusting the screw feet.
• If, for space reasons, it is not possible to avoid setting up the unit directly next to a gas or coal-fired cooker: install a thermal insulation
panel between the cooker and washing machine (85 x 57cm) which
must have an aluminium film on the side against the cooker.
• The washing machine must not be set up in a room where there is a
danger of frost. Frost hazard!
• Flexible feed and drain tubings may not be crinkled or squeezed.
Installation on a concrete base
If the unit is set up on a concrete
base, for safety reasons it is essential to fit stand plates in which the
washing machine is adjusted. The
stand plates are available from
Customer Service under the spare
parts number 645 425 058.
57
Installation on vibrating floors
Where the floor vibrates, particularly in the case of wooden beam
floors with pliable boards, securely screw a water-resistant wooden
panel at least 15mm thick onto at least 2 floor planks. If possible, set up
the unit in the corner of a room, as the wooden floor is optimally restrained there and is therefore least likely to be subject to resonance vibrations.
Compensate for floor unevenness
3
Automatic adjustment foot: The rear left foot of your washing machine is designed as a spring leg. This means that it guarantees that
your unit will stand securely even at high spin speeds.
If, nevertheless, the washing machine is unstable during spinning,
please proceed as follows:
0 1. Set the three adjusted feet at the
nominal value of 10 mm. To do
this, use the supplied special
spanner to remove the transport
safeguard.
If the automatically adjusting
foot does not reach the floor:
2. Automatic adjustment foot (rear
left) manually for extending the
reqired dimension.
3. If necessary, check the setting
with a spirit level.
Caution! Never use wood, card or similar underlays to level out minor
floor unevenness. Instead, always adjust
the adjustment foot.
58
Electrical connection
5
Details of the mains voltage, current
type and required fuses can be
found on the rating plate. The rating plate is located at the top above
the filling door.
For permanent electrical connection
within the electrical circuit, provisions must be made which allow for electrical disconnection of the appliance from the mains with a contact opening of at least 3 mm at all
poles. Suitable devices include circuit breakers, fuses (threaded fuses
must be entirely removed from the socket), ground fault circuit interrupters and contactors. Permanent connection may only be carried out
by an authorised electrician.
This appliance complies with the following EC directives:
– The "Low Voltage Directive" 72/23/EU with changes
– The "EMC Directive" 89/336/EU with changes
Water connection
3
The washing machine has safety features which prevent back-contamination of the drinking water and which conform to the national regulations of the water authorities (e.g. for Germany: DVGW guidelines).
This means that additional protective measures in the installation are
not necessary.
Important!
– Units for connecting to cold water must not be connected to hot water.
– Use only new hose sets for the connection.
Permissible water pressure
The water pressure must be at least 1 bar (= 10 N/cm2 = 0.1 Mpa), maximum 10 bar = 100 N/cm2 = 1 Mpa).
• If more than 10 bar: Connect a pressure-reduction valve upstream.
• If less than 1 bar: Unscrew the inlet hose on the unit side at the solenoid intake valve and remove the flow regulator (to do this, remove
the filter with pointed pliers and take out the rubber washer behind).
Replace the filter.
59
Water inflow
3
A pressure hose 1.5m in length is supplied.
If a longer inflow hose is required, only a VDE-approved, complete set
of hoses with fitted hose screw connections offered by our Customer
Service is permissible.
– Hose sets in lengths of 2.2m, 3.5m and 5m are available for washing
machines without Aqua-Control.
– Hose sets in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control.
Caution! Never cut into pieces in order to extend the hoses!
Sealing rings are supplied either
in the plastic nuts of the hose
screw connection or in the enclosed pack. Do not use other
seals!
1. Connect the hose with the angled
connection to the machine.
Caution!
– Do not lay the infeed hose vertically downwards. Instead, turn
it to the right or left as shown
in the diagram.
– Tighten the hose connection
only by hand.
2. Connect the hose with the
straight connection to a water
tap with a R 3/4 (inch) screw
thread.
Caution! Only tighten the screw
connection manually.
3. By slowly opening the water tap
before putting the washing machine into operation, check that
the connection is free of leaks.
60
Water drain
The drainage hose can either be connected to a siphon or hung in a
wash basin or discharge basin or a bath tub.
Only original hoses may be used for extensions (max. 3m laid on the
floor and then up to 80cm high). Customer Service stocks drainage
hoses in lengths of 2.7 and 4m.
Important! It is essential to lay the drainage hose without kinks.
Water drain-off inside a siphon
The grommet on the hose end fits
all standard siphon types.
Secure the connection between
the grommet and siphon with a
hose clamp.
Water drain-off inside a basin
Important!
– Small basins are not suitable for
drainage. Water could overflow!
– The end of the drainage hose
must not be submerged in the
pumped-out water. Otherwise,
the water could be sucked back
into the unit.
– When hanging in a wash basin
or a bath tub, the drainage hose
must be secured with the supplied attachable bend to prevent it slipping. The back-surge
force of the escaping water
could otherwise force the hose
out of the basin.
Tie the bend to the tap or the wall
using a piece of string.
Delivery heads over 1m
To pump off the washing / rinsing solution, every washing machine has
a drain pump which carries liquids up to a height of 1m via the drainage hose, calculated from the machine's standing surface.
Please contact Customer Service for delivery heads of over 1m.
61
Technical data
Adjustment possibility
Approx. +10 / -5mm
Filling quantity (program-dependent)max. 5kg
Area of use
Domestic
Drum speed, spinning
See rating plate
Water pressure
1-10 bar (= 10 - 100 N/cm2
= 0.1 - 1.0 Mpa)
Dimensions
(dimensions in mm)
62
Customer Services
Schweiz - Suisse - Svizzera
A + T Hausgeräte AG
Kundendienst AEG
Industriestraße 10
5506 Mägenwil
Service
Eine Tel.-Nr. für die ganze Schweiz
ServicePhon 0848 848 348
Fax 062/889 95 85
Ersatzteildienst
Ersatzteilverkauf ganze Schweiz
Telefon 0848 848 028
Fax
062/889 94 90
Regionalbüro Westschweiz:
1028 Préverenges
Le Trési 6,
Verkauf Tel. 021/803 24 15
Fax 021/803 25 24
Regionalbüro Tessin:
6616 Losone
Centro Montana
Verkauf Tel. 091/791 14 12
Fax 091/792 18 03
Zudem besteht ein dichtes Netz
von AEG-Servicestellen.
Nous disposons en outre d’un réseau
de points de Service après-vente AEG.
Esiste inoltre una rete di centri
di servizio AEG.
63
64
65
Index
A
O
Aqua Control. . . . . . . . . . . . . . . . . . . . . . 45, 50
Automatic adjustment foot. . . . . . . . . . 10, 58
Opening the door . . . . . . . . . . . . . . . . . 27, 44
Options . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 30
Overdosing . . . . . . . . . . . . . . . . . . . . . . . . . . .34
C
Care agent . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Child safety feature . . . . . . . . . . . . . . . . 43, 51
Coloureds. . . . . . . . . . . . . . . . . . . . . . . . . 17, 23
Cottons . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 23
Curtains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Customer service . . . . . . . .41, 42, 50, 63, 67
D
Delay start . . . . . . . . . . . . . . . . . . . . 19, 30, 31
Delicates . . . . . . . . . . . . . . . . . . . . . . . . . 17, 23
Detergent . . . . . . . . . . . . . . . . . . . . 10, 24, 29
Detergent drawer . . . . . . . . . . . . . . . . . . 10, 28
Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 33
water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Drain pump . . . . . . . . . . . . . . . . . . . . . . . 10, 49
E
Easy iron . . . . . . . . . . . . . . . . . . 18, 23, 33,
Emergency drainage. . . . . . . . . . . . . . . . . . .
Energy saving . . . . . . . . . . . . . . . . . . . . . . . .
Extras . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20,
44
48
17
35
F
Pre wash . . . . . . . . . . . . . . . . . . . . . . . . . 20, 28
R
Rating plate . . . . . . . . . . . . . . . . . . . 10, 59, 67
Refresh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Rinse hold. . . . . . . . . . . . . . . . . . . . . 19, 29, 33
Rinse+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Risk of frost . . . . . . . . . . . . . . . . . . . . . . . 6, 48
S
Sensitive . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Short spin . . . . . . . . . . . . . . . . . . . . . . . . 18, 33
Silk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 23
Softener . . . . . . . . . . . . . . . . . . . . . . . 8, 10, 28
Spin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 33
Stain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 47
Stain removal agent . . . . . . . . . . . . . . . 10, 28
Stand-by mode . . . . . . . . . . . . .30, 33, 44, 45
Starch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
T
Fashion. . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 23
Time saving. . . . . . . . . . . . . . . . . . . . . . . . . . .19
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 25
G
U
Gentle spin . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
H
V
Handwash . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
L
W
Language . . . . . . . . . . . . . . . . . . . . . . . . . 21,
Linen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17,
Linen/Easy-care. . . . . . . . . . . . . . . . . . . . 17,
Lingerie . . . . . . . . . . . . . . . . . . . . . . . . . . 18,
Load size . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
23
23
23
52
M
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 35
N
Navigation display . . . . . . . . . . . . . . . . . 11, 13
66
P
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 6, 42
Washing powder . . . . . . . . . . . . . . . . . . . . . .24
Water
hardness . . . . . . . . . . . . . . . . . . . . . . . . 8, 24
softener . . . . . . . . . . . . . . . . . .8, 10, 24, 28
Water cooling . . . . . . . . . . . . . . . . . . . . . . . . 21
Woollens. . . . . . . . . . . . . . . . . . . . . . . . . 17, 23
Service
In the chapter "What to do if...“ , some faults are listed which you can
remedy yourself. Look there first if a fault occurs. If you do not find any
information there, please consult your Customer Service. (You can find
the addresses and telephone numbers in the section "Customer Service
Centres“.)
Always prepare in advance for the discussion. By doing so you will simplify the diagnosis and the decision on whether customer service is
necessary.
Note the PNC number and S.
number. You will find both on the
rating plate on the inside of the door
of your washing machine.
PNC .....................................................
S-No. .....................................................
Answer as precisely as possible:
• What form does the fault take?
• Under what circumstances does the fault occur?
• Does the display show an error message?
When do you incur costs even during the warranty period?
– If you could have remedied the fault yourself with the aid of the fault
table (see the section "What to do if..."),
– If several journeys by the customer service technician are necessary
because for example he did not receive all the important information
before his visit and must collect spare parts. These multiple trips can
be avoided if you prepare your phone call as described above.
67
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
822 943 560-01-010403-01
Subject to change without notice