Operating instructions | AEG 50800 Dishwasher User Manual

ÖKO_FAVORIT 50800
Dishwasher
User Instructions
Dear customer,
Please read these user instructions carefully.
Above all please observe the safety instructions on the first few pages
ofthese user instructions! Please keep these user instructions for later
reference. Pass them on to any subsequent owner of the appliance.
1
0
The warning triangle and/or specific words (Warning!, Caution!,
Important!) are used to highlight instructions that are important for
your safety or for the function of the appliance. It is imperative that
these instructions are observed.
This symbol or numbered instruction steps lead you step for step
through the operation of the appliance.
3
Next to this symbol you receive additional information and practical
tips on using the appliance.
2
Tips and instructions for the economical and environmentally conscious
use of the appliance are marked with a clover leaf.
In the event of a malfunction, these operating instructions contain
information on how to rectify faults yourself, see the "What to do, if..."
section.
If these instructions are insufficient, please contact your nearest customer service centre.
In the case of technical problems, our customer service organisation is
available to provide you with assistance at any time (you will find
addresses and telephone numbers in the "Customer Service Centres"
section).
In this respect please read the "Service" note on the rear of these user
instructions.
3
Your dishwasher is fitted with the new "PULSE WASH" wash system.
With this wash system, the motor speed and spray pressure are
varied during the wash programme to improve the cleaning of the
dishes. It is for this reason that the noise level changes during the
wash programme.
Printed on paper manufactured with environmentally sound processes.
He who thinks ecologically acts accordingly ...
2
Contents
CONTENTS
Operating Instructions
....................................
5
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Appliance Features and Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
9
Prior to using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjust the water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filling with Special Salt for the Water Softener . . . . . . . . . . . . . . . . . . . . .
Filling with Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting Rinse Aid Dosing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
11
12
13
In Daily Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading cutlery and dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Cutlery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Pans, Frying Pans and Large Plates . . . . . . . . . . . . . . . . . . . . . .
Loading Cups, Glasses and Coffee Services . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Height of the Upper Basket . . . . . . . . . . . . . . . . . . . . . . .
Filling with Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bio Wash Programmes and Concentrated Detergents . . . . . . . . . . . . . .
Selecting the Wash Programme (Programme Table) . . . . . . . . . . . . . . . . . .
Start the wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing/Interrupting/Cancelling the Wash Programme . . . . . . . . . . .
Setting or Changing the Start Delay Timer . . . . . . . . . . . . . . . . . . . . . . .
Load Sensing – Sensor Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Off the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emptying the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
15
16
17
18
19
20
21
22
22
23
24
24
24
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cleaning the Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
What to do, when ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
...Error messages are displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
...problems occur during use of the dishwasher. . . . . . . . . . . . . . . . . . . . . .
...the wash results are not satisfactory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
27
28
28
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Notes for Test Institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3
Contents
Installation and Connection Instructions . . . . . . . . . . . . . . . .
31
Installing the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Free-Standing Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Connecting the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Permitted water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect the inlet hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leak Prevention System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
33
33
33
34
35
35
36
Service Departments
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
South Africa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Other Countries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Guarantee Conditions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
South Africa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Other Countries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Service
4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Operating Instructions
OPERATING INSTRUCTIONS
1
Safety Instructions
The safety aspects of AEG electrical appliances comply with accepted
technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you
aware of the following safety information:
Installation, Connection and Placing into Operation
• The dishwasher may only be transported upright.
• Check the dishwasher for transport damage. Do not in any circumstances connect an appliance that is damaged. In the case of damage,
please contact your supplier.
• Prior to placing the appliance in operation, ensure that the nominal
voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be
found on the rating plate.
• For information on how to correctly install and connect up your dishwasher, please read the „Installation“ section. Multiway plugs / connectors and extension cables must not be used. This could constitute
a safety hazard.
Child Safety
• Children often do not recognise the hazards associated with the use
of electrical appliances. It is therefore important that you ensure
children are adequately supervised and that you do not allow children to play with the dishwasher – there is a risk that children can
shut themselves inside the appliance (risk of suffocation!).
• Packaging materials (e.g. films, styrofoam) can be dangerous for children. Risk of suffocation! Keep packaging away from children.
• Detergents can cause burns to the eyes, mouth, and throat, or even
cause choking! Please observe the manufacturer's safety instructions
for cleaners and detergents.
• The water in your dishwasher is not suitable for drinking. If there are
still remnants of detergent in the appliance, there is a risk of burns!
• When disposing of the dishwasher: unplug from the mains, cut off
and dispose of the mains cable. Break the door lock so that the door
no longer shuts.
5
Operating Instructions
General Safety
• Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for
the user. If your appliance needs repairing, please contact customer
service or your dealer.
• Never place the dishwasher in operation if the mains cable, water
inlet or drain hose is damaged; or the control panel, work top or
plinth area is damaged such that the inside of the appliance is freely
accessible.
• If the mains lead is damaged, or is to be replaced for a longer lead,
the cable (obtainable from AEG customer service) must be replaced
by a service engineer authorised by AEG.
• Never unplug the appliance by pulling on the cable, always pull the
plug.
• Additions or modifications to the dishwasher are not permitted for
safety reasons.
• Ensure that the door of the dishwasher is always closed when it is not
being loaded or unloaded. In this way you will avoid anybody tripping
over the open door and hurting themselves.
• Sharp knives and other item of cutlery with sharp edges must be laid
in the upper rack or placed in the cutlery rack with the point facing
downwards.
Correct Use
• Only wash household dishes using the dishwasher. If the appliance is
used for other purposes, or is used incorrectly, the manufacturer cannot accept any liability for any damage caused.
• Prior to use, ensure that the manufacturers of the special salt, detergent, and rinse aid employed specifically permit the usage of their
products in household dishwashers.
• Do not put any solvents in the dishwasher. There is a risk of an explosion!
• The anti-flood system provides dependable protection against damage due to leaks. For this system to function correctly, the following
preconditions must be met:
– The appliance must remain connected to the mains even when it is
switched off.
– The dishwasher must be correctly installed.
– Always shut off the water supply at the tap when the dishwasher is
not to be used for longer periods, e.g. when you are away on holiday.
6
Operating Instructions
• Do not sit or stand on the open door, the appliance may tip over.
• In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently
wired to the mains: switch off the fuse(s) or unscrew them.
2
Disposal
Disposing of the Packaging Material
Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled.
• Plastic parts are marked with standard international abbreviations:
– >PE<
for polyethylene, e.g. sheet wrapping material
– >PS<
for polystyrene, e.g. padding material (always CFC-free)
– >POM< for polyoxymethylene, e.g. plastic clips
• Cardboard packaging is manufactured from recycled paper and
should be deposited in the waste paper collection for recycling.
Disposal of old appliances
As and when you cease to use your dishwasher, please take it to a recycling centre or to your dealer who will, for a small contribution to the
costs, dispose of it for you.
2
Economical and Ecological Dishwashing
• Only connect the dishwasher to the hot water supply if your hot
water is not electrically heated.
• Ensure that the water softener is correctly adjusted.
• Do not pre-rinse dishes under running water.
• When you wash a small load, the load sensor calculates the amount
of water necessary and shortens the programme. It is more economical to always wash with a full load.
• Select the wash programme to suit the nature and degree of the soiling on the dishes.
• Do not use more detergent, special salt or rinse aid than is recommended in these operating instructions and by the manufacturer of
the respective product.
7
Operating Instructions
Appliance Features and Control Panel
Top Spray
Nozzle
Rubber Seal for
Connecting the
Water Feed to
the Upper Spray
Arm
Spray Arms
Container for
Special Salt
Container
for Rinse Aid
Detergent
Dispenser
Suction Opening for Fan
Assisted Drying
8
Rating Filters
plate
Operating Instructions
Control panel
Function Softener
Button Button
Control Field
Door Handle
Air Outlet for Fan
Assisted Drying
Set
Start Delay
Indicators
Multi-Display
The Control Field comprises the ON/OFF switch M and the programme buttons with LED indicators.
Softener and Function Button: in addition to the wash programme
marked, it is also possible to adjust the dishwasher's water softener
using the combination of these buttons.
The Multi-Display can display,
– the hardness setting to which the water softener is set.
– the start delay that is set.
– how long the current wash programme can be expected to last.
– which fault has occurred on the dishwasher.
The Indicators have the following meanings:
J
Refill with special salt
G
Refill with rinse aid
^
Open the tap
\
Clean the dishwasher’s filter system
Prior to using for the first time
Prior to using for the first time, remove all the clips with which the dish
racks are secured for transport.
Then perform the following steps:
0 1. Adjust the water softener
2. Filling with Special Salt for the Water Softener
3. Filling with Rinse Aid
9
Operating Instructions
Adjust the water softener
To avoid the scale deposits on the dishes and in the dishwasher, the
dishes must be washed with soft, i.e. low lime content, water. The dishwasher therefore has a built-in water softener, in which tap water from
a hardness of 4 °d (German degree) is softened with the aid of special
salt.
3
0
You water supplier will be able to inform you on the hardness and
hardness range of the water in your area.
Adjust the water softener to the setting given in the table that corresponds to the hardness of the water in your area. The water softener
can be adjusted in 10 steps.
in °d1)
Water Hardness
in mmol/l 2) Range
Adjust
to Hardness Setting
Indication on the
Multi-Display
H9
H8
H7
H6
H5
41-50
35-40
31-34
27-30
23-26
7.3-9.0
6.3-7.2
5.5-6.2
4.8-5.4
4.1-4.7
IV
9
8
7
6
5
19-22
15-18
3.3-4.0
2.6-3.2
III
4
3*
H4
H3
11-14
1.9-2.5
II
2
H2
4-10
0.7-1.8
I/II
1
H1
under 4
under 0.7
I
0
no salt necessary
H0
1)(°d) German degree, measure of the hardness of water
2)(mmol/l) millimol per litre, international unit for the hardness of water
*factory setting
0 1. The dishwasher must be switched off.
2. Press the function and water softener buttons simultaneously and keep
them pressed
3. In addition press the ON/OFF switch.
The LED indicators for the function and water softener buttons flash.
4. Press the softener button again.
The multi-display indicates the hardness setting.
5. Pressing the water softener button increases the hardness setting by 1.
(Exception: hardness setting 0 follows hardness setting 9).
10
Operating Instructions
6. When the hardness setting is correct, press the ON/OFF switch.
The hardness setting is then saved.
Filling with Special Salt for the Water Softener
1
Use only special salt for dishwashers. Never fill the salt container with
any another type of salt (e.g. culinary salt) or dishwasher detergent.
This would irreparably damage the water softener.
Prior to filling with salt, please check each time that you really do have
a packet of special salt in your hand.
Fill with special salt:
– Prior to using the dishwasher for the first time
– When the SALT indicator J on the control panel is illuminated.
3
If the water hardness in your area is less than 4 °d, you do not need to
use special salt.
0 1. Open the door, remove the lower
rack.
2. Undo the lid on the salt container by
turning it anticlockwise.
3. Only when using for the first time:
fill the salt container with water.
4. Place the funnel supplied on the container opening.
Fill the container with special salt
through the funnel; the capacity of
the container is approx. 1.0-1.5 kg
depending on the grain size. Do not
overfill the salt container with special salt.
3
LE
SA ALT Z
S AL
S EL
S
The water expelled by filling the salt container with special salt runs
out of the salt container onto the base of the washing compartment.
This is not a cause for concern, the water will be pumped out at the
start of the next wash programme.
5. Clean any salt remnants on the container opening.
6. Turn the lid clockwise to the stop, otherwise special salt will leak into
the wash water, this could lead to poor wash results. To avoid this run a
rinse programme after filling the salt container with special salt. This
will wash away salt water and any salt crystals that have been spilt.
11
Operating Instructions
Depending on the size of the salt grains, it can take several hours for
the salt to dissolve in the water and the special salt indicator J to
extinguish. The setting of the water softener and thus the consumption
of salt are dependent on the hardness of the local water.
3
Filling with Rinse Aid
Rinse aid ensures that your dishes gleam and are free from spots, and
that you glasses are clear.
1
Use only branded rinse aid for dishwashers. Never fill the rinse aid container with any another substance (e.g. concentrated vinegar). This
would damage the appliance.
Fill with rinse aid:
– Prior to using the dishwasher for the first time
– When the RINSE AID indicator H on the control panel is illuminated.
The rinse aid compartment is on the inside of the dishwasher door.
0 1. Open the door.
2. Press the rinse aid compartment
release button with your finger.
3. Fully open the rinse aid compartment
lid.
12
Operating Instructions
4. Fill with rinse aid exactly up to the
level marked “max”; this corresponds
to a quantity of approx. 140 ml.
5. Close the lid and press until it locks
into place.
6. Wipe up any spilt rinse aid with a
cloth. Otherwise too much foam will
be formed during the wash.
Adjusting Rinse Aid Dosing
3
As the dishes are washed rinse aid is released from the dispenser into
the wash water. The dose is factory set at 4, and can be adjusted from
1 to 6. Only change the setting if streaks, milky spots or dried on water
marks are visible on glasses or crockery.
0 1. Open the door of the dishwasher.
2. Press the rinse aid compartment
release button with your finger.
3. Fully open the rinse aid compartment
lid.
4. Set the dose level.
5. Close the lid and press until it locks
into place.
6. If rinse aid has run out, wipe up with
a cloth.
13
Operating Instructions
In Daily Use
• Is it necessary to refill with special salt or rinse aid?
• Load cutlery and dishes into the dishwasher
• Fill with dishwasher detergent
• Select a wash programme suitable for the cutlery and dishes
• Start the wash programme
Loading cutlery and dishes
1
Sponges, household cloths and any object that can absorb water may
not be washed in the dishwasher.
For washing in the dishwasher the following cutlery/dishes
are not suitable:
• Cutlery with wooden, horn,
china or mother of pearl handles
• Plastic items that are not heat
resistant
• Older cutlery with cement that is
not temperature resistant
• Bonded cutlery items or dishes
• Pewter or copper items
• Lead crystal glass
• Steel items subject to rusting
• Wooden platters
• Items made from synthetic fibres
are of limited suitability:
• Only wash stoneware in the dishwasher if it
is specifically marked as being dishwashersafe by the manufacturer.
• Glazed patterns may fade if machine
washed frequently.
• Silver and aluminium parts have a tendency
to discolour during washing. Left-overs, e.g.
egg white, egg yolk and mustard often
cause discolouring and staining on silver.
Therefore always clean left-overs from silver
immediately, if it is not to be washed
straight after use.
• Some types of glass can become dull after a
large number of washes.
• Before loading the dishes, you should:
– Remove large left-overs.
– Soften remnants of burnt food in pans.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation of the spray arms.
– Load hollow items such as cups, glasses, pans, etc. with the opening
downwards so that water cannot collect in the container or a deep
base.
– Dishes and items of cutlery must not lie inside one another, or
cover each other
14
Operating Instructions
– To avoid damage to glasses, they must not touch
– Do not lay small objects (e.g. lids) in the cutlery rack
Loading Cutlery
Long, pointed items of cutlery in the
cutlery rack are a hazard, particularly
to children (see Safety Instructions).
To ensure that all items of cutlery are
completely washed, you should
1. Place the grid insert on the cutlery
rack
2. Place short knives, forks and spoons
in the grid insert with their handles
pointing downwards.
1
To make the removal of cutlery easier, on some dishwasher models it
is possible to open the cutlery rack.
If you use the grid insert then the
cutlery rack cannot be opened.
To ensure that the cutlery rack cannot open on removal from the appliance, you should always hold both
parts of the two part handle.
0 1. Place the cutlery rack on a table or
work surface
2. Open the two part handle
3. Remove cutlery
4. Close the two part handle.
1
15
Operating Instructions
Loading Pans, Frying Pans
and Large Plates
Load large and heavily soiled dishes
in the lower rack.
To ease the loading of large items at
some dishwasher-models the two
rows of prongs for the right-hand
plate insert can be folded down:
0 1. Slightly lift the right plate insert.
3
2. Fold the plate insert to the left.
16
Operating Instructions
Loading Cups, Glasses and
Coffee Services
Load small, delicate items and long
pointed cutlery in the upper rack.
• Arrange items of crockery on the
folding cups racks so that they are
offset from each other and water
can reach all items.
• The cup racks can be folded up out
of the way for tall items.
• Lay or hang wine, champagne, and
brandy glasses in the cut outs on
the cup racks.
• Glasses, beakers, etc. can also be
placed on the two rows of prongs
on the left of the upper rack.
17
Operating Instructions
Adjusting the Height of the Upper Basket
Maximum Height of the Dishes in the
Upper Basket
Lower Basketk
3
With upper basket raised
22 cm
31 cm
With upper basket lowered
24 cm
29 cm
The height of the basket can also be adjusted when it is loaded.
Depending on the model, your appliance is provided with one of the
following types of upper basket:
Lowering the Upper Basket:
0 1. Pull the upper basket out completely.
2. Lift the upper basket at the rear right
and lower.
Type 1
Raising the Upper Basket:
0 1. Pull the upper basket out completely.
2. Raise the upper basket at the rear
right, pull slightly forward and allow
to lock into place in the upper position.
Lowering the Upper Basket:
0 1. Pull the upper basket out completely.
2. Holding the upper basket at the rear
right, lift it as far as it will go and
then lower it vertically. The upper
basket will engage in the lower position.
Raising the Upper Basket:
0 1. Pull the upper basket out completely.
2. Holding the upper basket at the rear
right, lift it as far as it will go and
then lower it vertically. The upper
basket will engage in the higher
position.
18
Type 2
Operating Instructions
Filling with Detergent
1
Only use dishwasher detergent.
Fill with detergent:
– Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the
programme.
Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging.
The detergent compartment is on the
inside of the dishwasher door.
0 1. If the lid is closed:
press release button (1).
The lid springs open.
2
2. Fill the detergent dispenser with
detergent. The markings indicate the
dosing levels:
“20” corresponds to approx. 20 ml of
detergent,
“30” corresponds to approx. 30 ml of
detergent.
3. Close the lid and press until it locks
into place.
3
If the dishes are very heavily soiled
put additional detergent into the
adjacent chamber (2). This detergent
will take effect during the pre wash.
19
Operating Instructions
Bio Wash Programmes and Concentrated Detergents
Based on their chemical composition, dishwasher detergents can be
split into two basic types:
– Conventional, alkaline detergents with caustic components
– Weak alkaline concentrated detergents with natural enzymes.
20
2
The use of BIO wash programmes in conjunction with concentrated
detergents reduces pollution and is good for your dishes; the BIO wash
programmes are specially matched to the soil dissolving properties of
the enzymes in the concentrated detergent. It is for this reason that
BIO wash programmes can achieve the same results at 50 °C that can
otherwise only be achieved using 65 °C programmes.
During BIO programmes the water is briefly heated to more than 50 °C
so that the active oxygen becomes effective.
3
Detergent tablets from different manufacturers dissolve at different
rates. For this reason some detergent tablets cannot develop their full
cleaning power during short programmes. Therefore please use normal
programmes with pre wash when using detergent tablets.
Operating Instructions
Selecting the Wash Programme (Programme Table)
Choose the most suitable wash programme with the aid of this table:
Type of
Dishes
In Addition
-
Type of
Soiling
Suitable
Programme:
Consumption
Figures: 3)
-
• heavily
• normally
soiled
soiled
• dried on left- • dried leftovers, particovers
ularly egg
white and
thickeners
All Dish Types
with non-temperature resistant dishes
with
delicate glasses
-
• normally
soiled
• lightly
soiled
particularly suited to the use of
concentrated detergents.
ò
ò
ò
INTENSIVE
NORMAL
a7
Programme
Sequence 2)
Dessert Dishes
and Coffee
Service
Dinner Service and Cooking Utensils
Pre Wash
Main Wash
2x Intermediate Rinses
Final Rinse
Drying
ò
d6
Pre Wash
Main Wash
Intermediate
Rinse
Final Rinse
Drying
ò
Used dishes
that are being
collected in the
dishwasher for
washing later.
ò
ò
NORMAL BIO
QUICK
PRE WASH
1) 4)
]5
A
dQ
Pre Wash
Main Wash
Intermediate
Rinse
Final Rinse
Drying
ò
Main Wash
Intermediate
Rinse
Final Rinse
-
ò
Pre Wash
-
ò
Duration
110 – 120 min.
89 – 99 min.
Energy
1.9 – 2.1 kWh
1.15 – 1.35 kWh 0.85 - 1.05 kWh 0.85 kWh
< 0.1 kWh
Water
18 – 20 litres
14 – 16 litres
4 litres
1)
2)
3)
4)
110 - 120 min.
14 – 16 litres
30 min.
12 litres
10 min.
During BIO programmes the water is briefly heated to more than 50 °C so that the active oxygen
becomes effective.
The various stages in the wash programme have different sounds because the dishes are washed
more intensely for short periods during certain stages of the wash programme to improve cleaning.
The consumption figures were recorded under standard conditions. They are dependent on the loading of the dish racks. Variations are therefore possible in practice.
Test programme
21
Operating Instructions
Start the wash programme
0 1. Check that the dishes and cutlery are loaded into the dishwasher in
such a manner that the spray arms are free to rotate.
2. Open the tap fully.
3. Shut the door.
4. Press the ON/OFF button. The ON/OFF button indicator illuminates.
5. Press the programme button for the desired programme (see "Programme Table"). The programme indicator illuminates. The selected
programme begins after around 6 seconds. The time remaining until
the end of the programme is displayed on the multi-display, the time
calculated is dependent on the load in the dish racks.
With automatic programme adjustment this residual time count can be
stopped or corrected if necessary (load quantity, degree of dirtiness,
etc.) using the dishwasher control.
3
If fault messages are displayed on the multi-display after the start of
the programme, please read the "What to do, if..." section.
Changing/Interrupting/Cancelling
the Wash Programme
3
Only change or interrupt a wash programme in progress if it is absolutely necessary to do so. When the appliance is closed again, the air
that has entered is heated and expands significantly. As result water
may penetrate into the base of the appliance and trigger the leak prevention system.
Changing the wash programme
If you want to change the wash programme within 6 seconds of making a programme selection, briefly press the button for the new wash
programme.
If you want to change the wash programme at a later point in time, use
the following procedure:
0 1. Press the button for the new wash programme and hold it pressed. The
indicators for both programmes now flash.
2. After a few seconds only the indicator for the new programme flashes.
Release the programme button, the new programme is now running.
3
22
Operating Instructions
Interrupting the wash programme by opening the door of the
dishwasher
Hot steam may escape from the appliance when opening the door.
There is a risk of scolding! Open the door carefully.
0 1. Open the door of the dishwasher. The wash programme stops.
2. The indicator for the programme that is currently running extinguishes.
3. Close the door. The wash programme continues.
1
Cancelling the wash programme
0 1. Press the button for the current wash programme and hold it pressed.
The programme indicator for the current wash programme flashes for a
few seconds and then extinguishes.
2. Release the programme button, the wash programme is cancelled.
3
A selected programme is only interrupted by switching off the dishwasher, it is not cancelled. The wash programme is continued when the
dishwasher is switched on again.
Setting or Changing the Start Delay Timer
Using the start delay timer you can adjust when the wash programme
is to begin within the next 19 hours.
Setting the start delay timer:
0 1. Press the ON/OFF button.
2. Keep pressing the DELAY TIMER button b until the number of hours of
delay until the wash programme is to start are flashing on the multidisplay.
3. Press the button for the desired wash programme. The multi-display
now displays the number of hours without flashing. The number of
hours is saved.
4. The wash programme starts automatically at the end of the delay set.
Changing the start delay:
As long as the wash programme has not started, you can still change
the start delay set by pressing the DELAY TIMER button b.
23
Operating Instructions
Load Sensing – Sensor Logic
If a wash programme is started even though there are only a few dishes
in the upper and/or lower rack, an intelligent electronic system adjusts
the amount of water and the duration of the wash programme to the
number of dishes. By this means it is possible to wash only a few dishes
quickly and economically. At half load (6 place settings), up to 2 litres
of water and 0.2 kWh of electricity are saved.
Switching Off the Dishwasher
Only switch the dishwasher off when the multi-display indicates "0"
remaining programme time.
0 1. Press the ON/OFF button. The ON/OFF button indicator extinguishes.
Hot steam may escape from the appliance when opening the door
immediately after the end of the programme. Therefore:
2. Open the door carefully.
1
Emptying the Dishwasher
3
24
• Hot dishes are sensitive to knocks. The dishes should therefore be
allowed to cool down before removing them from the appliance.
• Leave the dishes in the dishwasher for approx. 15 minutes after the
end of the programme so that they dry better and can cool down.
• First empty the lower rack, and then the upper rack. By using this
procedure you will avoid any water that may be remaining in the
upper rack, dripping onto the dishes in the lower rack and leaving
water marks.
Operating Instructions
Care and Cleaning
1
Do not under any circumstances use furniture care products or aggressive cleaners.
• If necessary, clean the controls only with a soft cloth and pure warm
water.
• The spray arms do not need cleaning.
• Occasionally check the internal containers, door seal, and water inlet
for soiling, clean if necessary.
Cleaning the Filter
The filters in the base of the washing compartment are to a large
extent self-cleaning.
Nevertheless the filters should be
checked and cleaned from time to
time. Dirty filters will degrade the
washing result.
0 1. Open the door, remove the lower
rack.
2. The dishwasher filter system comprises a coarse/fine filter, microfilter
and a flat filter. Unlock the filter system using the handle on the microfilter, and remove.
3. Turn the handle about ¼ a turn anticlockwise and remove.
4. Take hold of the coarse/fine filter (1)
by the handle with the hole and
remove from the microfilter (2)
5. Clean all filters thoroughly under
running water.
6. Remove the flat filter (3) from the
base of the washing compartment
and clean both faces thoroughly
3
25
Operating Instructions
7. Put the flat filter back in the base of
the washing compartment
8. Place the coarse/fine filter in the
microfilter and press together.
9. Put the filter combination in place
and lock by turning the handle clockwise to the stop. During this process
ensure that the flat filter does not
protrude above the base of the washing compartment.
1
Under no circumstances may the
dishwasher be used without filters.
What to do, when ...
Try to rectify minor faults on the dishwasher with the aid of the
instructions given here. If you call in customer service to resolve one of
the malfunctions listed here, or rectify an error made in the operation
of the appliance, the customer service engineer’s visit is not free of
charge, even during the period of guarantee.
26
Operating Instructions
...Error messages are displayed.
• If fault code (2 is displayed on the multi-display or the ^ indicator
is illuminated, you can probably rectify the fault yourself.
After rectifying a (2 fault and a fault related to the ^ indicator,
press the button for the wash programme that has been started. The
wash programme continues. If the fault code is displayed again, contact customer service.
• For all other faults, please contact customer service, stating the fault
code.
Malfunction
The programme indicator for the selected
programme is flashing
and the ^ indicator is
illuminated:
there is no water running into the dishwasher.
Possible Cause
Remedy
Tap is blocked or furred with
Clean tap.
lime-scale.
The filter (where present) in
the threaded hose fitting at
the water inlet valve is
blocked.
Clean the filter in the
threaded hose fitting.
The water inlet hose is not
correctly laid.
Check hose installation.
Fault code (2 is disThe siphon is blocked.
played on the multidisplay.
The programme indica- The water drain hose is not
tor for the selected
correctly laid.
wash programme is
flashing.
Clean siphon.
Check hose installation.
Fault code (3 is displayed on the multidisplay.
The leak prevention system
has been triggered.
The [ indicator is
illuminated.
The [ indicator is only
intended to remind you to
check the filter in the dishThe indicator goes out autowasher from time to time
and, if necessary, to clean it. matically on the start of the
next wash programme.
It illuminates at regular
intervals, independent of the
amount of soiling of the filter.
Close the tap and contact
customer service.
27
Operating Instructions
...problems occur during use of the dishwasher.
Malfunction
Possible Cause
Remedy
The door of the dishwasher is
Shut the door.
not closed properly.
Mains plug is not plugged in. Insert mains plug.
House fuse is defective.
Replace fuse.
In the case of dishwasher
models with start delay
timer:
A start delay is selected.
Where dishes are to be
washed immediately, for
appliances
- with multidisplay, set the
delay start to 0.
- without multidisplay, cancel the delay start timer.
The programme does
not start.
The washing compartment is
made from rust-free stainless
steel. Rust spots in the washing compartment are due to
Rust spots are visible in rust particles from external
the washing compart- sources (rust particles from
water pipes, pans, cutlery,
ment.
etc.). Remove such spots with
one of the stainless steel
cleaners that are generally
available on the market.
Only wash cutlery and dishes
that are suitable for dishwasher use.
There is a whistling
noise during washing.
Use a different brand of
detergent.
The whistling is not a cause
for concern.
Close the lid of the special
salt container securely.
...the wash results are not satisfactory.
The dishes are still dirty.
– The wrong wash programme was selected.
– The dishes were loaded is such a way that the wash waster did not
reach all items. The racks for the dishes must not be overloaded.
– The filter in the base of the washing compartment is dirty or incorrectly positioned.
– Detergent was not used or too little was used.
– In the case of scale deposits on the dishes: The special salt container
is empty or the water softener is incorrectly adjusted.
– The drain hose is incorrectly laid.
28
Operating Instructions
The dishes are wet and dull.
– Rinse aid was not used.
– The rinse aid container is empty.
There are streaks, milky spots or a bluish coating on glasses and
dishes.
– Lower rinse aid dosing.
There are dried water drops on the glasses and dishes.
– Increase rinse aid dosing.
– The detergent may be the cause. Contact the detergent manufacturer’s customer advisor.
Technical Data
Capacity:
12 place settings including serving dishes
Permitted Water
Pressure:
1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa)
Electrical Connection:
Information on the electrical connection is given on the
rating plate on the inner edge of the dishwasher door on
the right.
Dishwasher: Free-Standing Appliances
Dimensions:
850 x 600 x 600 (H x W x D in mm)
Max. Weight:
54 Kg
Dishwashers that Can Be Integrated, Built-In Dishwashers
Dimensions:
820 – 880 x 596 x 570 (H x W x D in mm)
Max. Weight:
50 Kg
Dishwashers that Can Be Fully Integrated
Dimensions:
820 – 880 x 596 x 546 - 550 (H x W x D in mm)
Max. Weight:
50 Kg
; This appliance conforms with the following EU Directives:
– 73/23/EWG dated 19. 02. 1973 – Low Voltage Directive
– 89/336/EWG dated 03. 05. 1989
(including Directive Amendment 92/31/EWG) – EMC Directive
29
Operating Instructions
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the
appliance fully loaded and using the test programme (see Programme
Table).
Tests in accordance with EN 50242 must be carried out when the salt
dispenser and rinse aid container have been filled with salt and rinse
aid respectively and using the test programme (see Programme Table).
Full Load:
12 place settings
incl. serving dishes
Half Load:
6 place settings incl. serving, leaving
alternate positions free
Detergent Dosing:
5g + 25g (Type B)
20g (Type B)
Rinse Aid Setting:
4 (Type III)
4 (Type III)
Sample loading arrangements:
Upper basket
Lower basket with cutlery basket
30
Cutlery basket
Installation and Connection Instructions
INSTALLATION AND CONNECTION
INSTRUCTIONS
Installing the Dishwasher
• The dishwasher must be installed on a firm floor and adjusted to
ensure that it is stable and level.
• To compensate for unevenness in the
floor and to match the height of the
appliance to that of surrounding units
extend the threaded feet by unscrewing:
– use a screwdriver.
• The drain hose, inlet hose and mains cable must not be kinked or
crushed when the dishwasher is in position.
Free-Standing Appliances
1
• can be set up as stand-alone without additional installation.
If the dishwasher is set up next to a gas or coal cooker, a heatinsulating, non-flammable plate must be mounted between the
dishwasher and the cooker, flush to the top edge of the work surface
(depth 57.5 cm). The plate should have aluminium foil on the side
facing the cooker.
31
Installation and Connection Instructions
• If the dishwasher is installed underneath a kitchen work surface, the
original work surface of the dishwasher is to be removed as follows:
– Unscrew the screws (1) from the
elbows on the back side.
– Slide the work surface approx.
1cm to the rear (3) , lift at the
front (4) and remove.
– Press the work surface retaining
brackets at the position shown in
the diagram (4) and remove the
bracket at an angle to the rear
(5).
4
5
• The dishwasher must also be screwed on tightly to the work surface
or to the adjoining units. This is essential to ensure the dishwasher
does not tip.
32
1
If the dishwasher is later used as a free-standing appliance, the original
work surface must be re-mounted.
3
The plinth on free-standing appliances is not adjustable.
Installation and Connection Instructions
Connecting the Dishwasher
Water Connection
The dishwasher is fitted with safety devices that prevent the wash
water returning into the drinking water system and comply with the
applicable plumbing regulations.
• The dishwasher can be connected to cold and hot water supplies up
to max. 60 °C.
• The dishwasher must not be connected to open hot water appliances
or instantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure:
1 bar (=10 N/cm2 =100 kPa)
Consult your installer if the water pressure is less than 1 bar.
Highest permitted water pressure:
10 bar (=100 N/cm2 =1 MPa)
In the case of a water pressure greater
than 10 bar, a pressure reduction valve
must be used (available from your
dealer).
Connect the inlet hose
1
0
3
The water inlet hose must not be kinked, crushed or entangled when it
is being connected up.
Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet
hose to a tap with an external thread (¾ inch). Tighten the threaded
hose fitting hand tight only.
• In order that access to the tap in the kitchen is not limited by the use
of the dishwasher, we recommend the installation of an additional
tap, or fitting a two way adapter to the existing tap.
• If you need a longer water inlet hose than that supplied, VDE
approved complete hose sets are to be used. These are available from
your local Service Force Centre.
33
Installation and Connection Instructions
Water drain
Drain hose
1
The drain hose must not be kinked, crushed or entangled.
• Connecting the drain hose:
– Maximum permitted height: 1 metre.
– Minimum required height 30 cm above the lower edge of the
machine.
Extension hoses
• Extension hoses are available from
your dealer or customer service.
The internal diameter of the extension hoses must be 19 mm to
ensure that the function of the
appliance is not impeded.
• Extension hoses may be laid a maximum of 3 metres horizontally; the
maximum permitted height for the
connection for the drain hose is
then 85 cm.
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all commonly available
sink outlet spigot types. The outer diameter of the spigot connection
must be at least 15 mm.
• The drain hose must be fixed to the sink outlet connection using the
hose clamp supplied.
If the dishwasher is fitted at a high position
If the dishwasher is installed at a high level, and the drainhose connection is less than 30 cm from the bottom of the appliance, adapter kit
ET 111099520 must be fitted. This is available from Customer Service.
Water drain into wash basins (only possible with free-standing
appliances)
In the case that you wish to hang the drain hose in a wash basin, use a
detachable hose elbow. You can obtain this from AEG customer service
under spare part number ET 646 069 190.
0 1. Fit the elbow to the drain hose.
2. Secure the drain hose against sliding off the edge of the wash basin.
Pass a piece of cord through the hose elbow and fix it to the wall or the
tap.
34
Installation and Connection Instructions
Leak Prevention System
For protection from damage due to water leaks, the dishwasher is
equipped with a leak prevention system, the AQUA CONTROL SYSTEM.
In the event of a fault, the safety valve immediately interrupts the supply of water to the appliance and the drain pump switches on. By this
means water can neither escape nor overflow. The remaining water in
the appliance is automatically pumped out.
1
The AQUA CONTROL SYSTEM also works when the appliance is switched
off – the appliance must however not be disconnected from the mains.
Electrical connection
1
In compliance with electric company technical requirements for mains
connections, hard-wired connections to the mains may only be made
by approved electri-cians.
When connecting the appliance, observe the German VDE regulations
and, if applicable, any additional conditions required by your local electricity supplier. Following installation, live parts and live insulated wiring must not be accessible using a finger test in accordance with EN
60335/DIN VDE 0700.
Information on the electrical connection can be found on the rating
plate on the right side of the inner edge of the dishwasher door. If the
appliance has a change-over switch, the additional instructions on the
change-over diagram in the mains connector box must be observed.
Prior to connecting ensure that the mains voltage and current rating at
the site of installation match the nominal voltage and current rating
given on the rating plate. The required fuse protection is also to be
found on the rating plate.
To isolate the dishwasher from the mains, remove the mains plug.
Important: The plug must still be accessible after the appliance has
been installed.
If the appliance is hard-wired to the mains supply, then it must be
safely isolated from the mains within the electrical installation with
switches intended to ensure all-pole(N,L1) disconnection, shall be
directly connected to the supply terminals and shall have a contact
separation (fuses, cut outs, current trips or similar) of at least 3mm in
each pole.
35
Installation and Connection Instructions
Connections
The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the
appliance.
The plumbing and electrical installation example given below can only
be regarded as a recommendation; the actual situation where the dishwasher is to be installed will define the exact installation (available
connections, local electricity and water board regulations for connecting up appliances, etc.).
Two 45° or Straight Connections,
Outer ø 19 mm, Length 30 mm
Water
inlet
36
Mains
cable
Water
drain
Mains socket
Double tap
Water drain
Mains
cable
Water inlet
Service Departments
SERVICE DEPARTMENTS
South Africa
South Africa
AEG Domestic Appliances
Head Office
55, 12th Road, Kew
P.O. Box 3657
JOHANNESBURG 2000
Tel.: elfa(011) 806-9111
Telefax: (011) 887-0849
DURBAN
84 & 73 Victoria Park
123 Old North Coast Road
Glen Anil
P.O. Box 1061
DURBAN 4999
Tel.: elef(031) 569-1470
Telefax: (931) 569-1498
CAPE TOWN
43 Neptune Street
Paarden Eiland
P.O Box 184
PAARDEN EILAND 7420
Tel.: elef(021) 511-0486
Telefax: (021) 510-5073
PORT ELISABETH
43 Pickering Street
Newton Park
P.O. Box 1231
PORT ELISABETH 6001
Tel.: elef(041) 353-600
Telefax: (041) 354-015
37
Service Departments
Other Countries
38
Malta
ITC
International Trading Company
White House Building
Mountbatte Street
Blata L-Bajda/Tel.: 220644
U.A.E. Abu Dhabi
Universal Trading Company
P.O. Box 43 99
Tel.: 335331
Jordan
Jordan Household
Supply Co. Ltd.
P.O. Box 3/68
Amman/Tel.: 69 70 50
Egypt
Middle East Commercial
Center
P.O. Box 19
Kairo-Heliopolis
Tel.: 29917/31634
Mauritius
Kanada
Happy World Centre Ltd.
EURO-LINE Appliances
2150 Winston PARK Drive 20 P.O. 7 54
1 Chausee Street
Oakville, Ontario L6H 5V1
Port Louis
Tel.: 905 829 3980
Tel.: 25355
Fax: 905 829 3985
Australia
ANDI-Co Pty. Ltd
9 Kingston Town Close
Oakleigh VIC 3166
Tel.: (03) 9569 1235
Fax: (03) 9569 1450
Korea (South)
Core Incorp.
3/F Chewoo Bldg.
200 Nonhyun-Dong
Kangnam-Ku
Seoul
Telefon 82 2 549 89 61
Namibia
AEG NAMIBIA (PTY) LIMITED-Jeppe Street
Northern Industrial Area
Windhoek
Tel.: (061) 21-6082/4
Fax: (061) 217838
Bahrain/Arabian Gulf
A.A. Zayani & Sons
P.O. Box 9 32
Bahrain
Tel.: 261060
Croatia
Electrolux D.O.O.
Suplova 7
10000 Zagreb
Tel.: 1 61 19512
Fax: 1 61 19513
New Zealand
Euro-Life New Zealand Ltd.
Privat Bag
58 Symonds Street
Auckland
Tel.: (09) 525 2222
Bulgaria
Electrolux Bulgaria E.O.O.D.
91 Levski Blvd.
1000 Sofia
Tel.: 2 806676
Fax. 2 980 5276
Kuwait/Arabian Gulf
Ali Al-Ghanim Est.
P.O. Box 10 83
Tel.: 5322463
Fax: 5242114
Nouvelle Caledonie
Socometra N.C.
B.P. 483
Nouman
Tel.: 275444
Service Departments
Cyprus
Hadjikyrlakos & Sons Ltd.
Prodromou 121
P.O. Box 21587
Nicosia 1511
Service Telephones:
Nicosia 02 481226
Limassol 05 562182
Larnaca 04 633929
Paphos 06 932 699
Estonia
Electrolux Estonia Ltd.
Mustamäe tee 24
EE0006 Tallinn
Tel.: (372) 6 650 090
Fax: (372) 6 650 092
Lebanon
Adib & Assaferi
P.O. Box 539
Tripoli
Oman
Moshin Haider Darwish
P.O. Box 1 35
Muscat
Tel.: 703743
Latavia
Electrolux Latavia Ltd.
Terlaton Street 42/44
1011 Riga
Tel.: 371 2 297821
Fax: 371 2 821286
Poland
Electrolux Poland Sp. zo.o.
ul. Domaniewska 41
02-034 Warszawa
tel.: 022 874 33 33
fax: 022 874 33 00
Hongkong
Wo Kee Services Ltd.
585-609 Castle Peak Road
Kwai Chung N.T.
Hongkong
Tel.: 2494 4000
Lthuania
Electrolux Lthuania
Verkui 29
2600 Vilnus
Tel.: 372 272 3326
Fax: 372 272 3366
Russia
Electrolux Russia Ltd.
16 Olympiysky prospekt
129090 Moscow
Tel.: (095) 937 7837
Fax: (095) 926 5513
Malaysia
Israel
Arzbergh Engineering
Electricity & Electronic
No. 49A/B, Jalan Petaling
Services-Evis LTD.
Utama 7
19 Hataasia st.
Raanana, Industrial area 43654 4600 Petaling Jaya
Tel.: 3 795 1084
Tel: 972-9-7448118
Fax: 3 795 1082
Fax: 972-9-7603618
e-mail:evis@evis.co.il
Japan
Electrolux Japan Ltd.
Yasuda Warehouse 4F 3-3-12
Heiwajima Ota-Ku
Tokyo
Tel.: 81 3 3544 3363
Fax: 81 3 3763 6143
Singapore
Arzbergh Engineering
19 Tanglin Road 06-07
Singapore 247909
Tel.: 65 7356572
Fax: 7351124
Saudi Arabia
Alia Trading Corporation
P.O. Box 4101
King Abdul Aziz Street
Riyadh
Tel.: 4645977
Al Nahas Est.
Musaidia Market I
P.O. Box 1 15 29
Jeddah
Tel.: 6606852
Slovenia
Electrolux Slovenia D.O.O.
Traska Ul. 132
1000 Ljubljana
Tel.: 61 1234 137
Fax: 61 1234 238
39
Service Departments
40
Thailand
OLYMPIA Thai Ltd.
44 Ratchadapisek Road
10320 Bangkok
Tel.: 2 513 6111
Fax: 2 513 2574
Slovakia Rep.
Electrolux Slovakia S.R.O.
Seberiniho 1
821 03 Bratislava
Tel.: 7 4333 9745
Fax: 7 4333 6976
South Africa
AEG (Pty) Ltd.
55, 12th Road
P.O. Box 1 02 64
Kew/Johannesburg 2000
Tel.: 8069111
Hungary
Electrolux Lehel KFT
(AEG Div)
Erzsebet’Kiralyne Utja 87
1142 Budapest
Tel.: 00361/251 84 44
USA
ANDI Co. Appl. Inc. East
65 Campus Plaza
Edison, New Jersey 0837
USA/Tel.: (201) 2258839
Syria
Masri & Shami
P.O. Box 24 96
Damascus
Tel.: 214080
Guarantee Conditions
GUARANTEE CONDITIONS
South Africa
Guarantee Conditions
1. AEG guarantees the equipment against defective material or faulty manufacture,
provided it is used for domestic purposes only, for a period twelve (12) months from
the date of purchase by the original purchaser. If used for commercial purposes, the
warrantly period will be limited to six (6) months.
2. Where the appliance is used or installed more than Fifty (50) kilometres from the
nearest AEG Service Agent shall be for the account of the purchaser.
3. The risk in regard to appliances to be repaired shall at all times remain with the purchaser.
4. This guarantee is given on condition that only genuine AEG parts and accessories are
at all times used in the appliance.
5. AEG shall not be responsible for damage of any kind resulting from electricity fluctuations, faults in the building wiring, faulty installations, improper use of controls or
failure to use the appliance in accordance with the operating instructions and/or general misure and/or abuse.
6. Any attempt by an unauthorised person to repair or tamper with the equipment
shall render this guarantee null and void.
7. This guarantee does not apply to light bulbs, loose glass, glass oven doors and enamelled surfaces or to dust bags, filters and other parts subject to wear and tear.
8. AEG shall not be responsible in terms of this guarantee for the replacement or repair
of any part of the equipment which may have been damaged in transit.
9. Repairs carried out under guarantee do not extend the guarantee period for the
appliance. Parts removed during guarantee repairs become the property of AEG.
10. This guarantee shall be available only to an original purchaser of AEG domesic
appliances from an authorised AEG Dealer of Distributor in and where the appliance
has been retained for use in the Republic of South Africa, Namibia, Botswana, Swaziland, Lesotho and Zimbabwe.
11. Failure to produce documentary proof of the date or original acquisition by the
original purchaser will result in normal charges being levied for the work carried out
and the parts supplied.
12. The liability of AEG under this guarantee is limited to the replacement and/or repair
of the defective parts within the guarantee period and does not extend to be installation or removal of the appliance. Furthermore, AEG does not accept responsibility or
liability to compensate for any consequential loss or damage of any kind caused by or
due to the failure of operation or malfunction of any equipment to which this guarantee applies.
AEG Domestic Appliances. A division of Electrolux S.A. (Pty) Ltd.
55 Twelfth Road, Kew, Johannesburg 2000
41
Guarantee Conditions
Other Countries
Weitere Kundendienststellen im Ausland
In diesen Ländern gelten die Garantiebedingungen der örtlichen Partner. Diese können dort eingesehen werden.
Further after-sales service agencies overseas
In these countries our AEG agents’ own guarantee conditions are applicable. Please obtain further details direct.
Autres agences étrangères assurant le service après-vente
Dans ces pays, les conditions de garantie des concessionnaires de la
région sont valables. Vous pouvez les consulter sur place.
Otros puntos de Postventa en el extranjero
En estos países rigen las condiciones de nuestros representantes locales.
las cuales pueden ser consultadas allí mismo.
Ulteriori uffici del servizio tecnico assistenza clienti all’estero
In questi paesi sono valide le condizioni di garanzia dei partner locali.
Queste condizioni possono essere esaminante sul luogo.
Serviços de assistência técnica no estrangeiro
Nestes países são válidas as condições de garantia dos concessionários
locais, podendo aí ser consultadas.
42
Service
SERVICE
In the section "What to do, if..." the most important sources of faults
that you can rectify yourself are summarised.
If, nevertheless, you call in customer service to resolve a problem listed
in these instruction, or because of an error made in operating the
appliance, the customer service engineer’s visit is not free of charge,
even during the warranty period.
If you can not find any information on a specific malfunction in these
operating instructions, please contact customer service.
Please provide customer service the PNC number and the S No. (serial
number), you can find these on the rating plate. The plate is on the
inner edge of the door on the right.
So that you always have these numbers at hand, we recommend you to
make a note of them here:
PNC :...............................................................................................................................
S-No. :.............................................................................................................................
43
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
822 945 537 - 00 - 1201
Subject to change without notice
Download PDF

advertising