User manual | AEG A62900GSX0 Freezer User Manual

Thank you for choosing this AEG product. We have
created it to give you impeccable performance for many
years, with innovative technologies that help make life
simpler – features you might not find on ordinary
appliances. Please spend a few minutes reading to get the
very best from it.
In the AEG webshop, you’ll find everything you need to
keep all your AEG appliances looking spotless and
working perfectly. Along with a wide range of accessories
designed and built to the high quality standards you
would expect, from specialist cookware to cutlery baskets,
from bottle holders to delicate laundry bags…
Visit the webshop at:
Safety information
Control panel
First use
Daily use
Helpful hints and tips
Care and cleaning
What to do if…
Technical data
Environmental concerns
The following symbols are used in this user
Important information concerning your
personal safety and information on how to
avoid damaging the appliance.
General information and tips
Environmental information
Subject to change without notice
Safety information
In the interest of your safety and to ensure the correct use, before installing and first using
the appliance, read this user manual carefully, including its hints and warnings. To avoid
unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.
For the safety of life and property keep the precautions of these user's instructions as the
manufacturer is not responsible for damages caused by omission.
Children and vulnerable people safety
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Keep all packaging well away from children. There is risk of suffocation.
• If you are discarding the appliance pull the plug out of the socket, cut the connection
cable (as close to the appliance as you can) and remove the door to prevent playing children to suffer electric shock or to close themselves into it.
• If this appliance featuring magnetic door seals is to replace an older appliance having a
spring lock (latch) on the door or lid, be sure to make that spring lock unusable before
you discard the old appliance. This will prevent it from becoming a death trap for a child.
General safety
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
• The appliance is intended for keeping foodstuff and/or beverages in a normal household
as explained in this instruction booklet.
• Do not use a mechanical device or any artificial means to speed up the thawing process.
• Do not use other electrical appliances (such as ice cream makers) inside of refrigerating
appliances, unless they are approved for this purpose by the manufacturer.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition
Safety information
– thoroughly ventilate the room in which the appliance is situated
• It is dangerous to alter the specifications or modify this product in any way. Any damage
to the cord may cause a short-circuit, fire and/or electric shock.
Any electrical component (power cord, plug, compressor) must be replaced by a certified
service agent or qualified service personnel to avoid hazard.
Power cord must not be lengthened.
Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire.
3. Make sure that you can come to the mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not insert the power plug. There is a risk of
electric shock or fire.
6. You must not operate the appliance without the lamp cover1) of interior lighting.
This appliance is heavy. Care should be taken when moving it.
Do not remove nor touch items from the freezer compartment if your hands are damp/
wet, as this could cause skin abrasions or frost/freezer burns.
Avoid prolonged exposure of the appliance to direct sunlight.
Bulb lamps2) used in this appliance are special purpose lamps selected for household appliances use only. They are not suitable for household room illumination.
Daily Use
Do not put hot pot on the plastic parts in the appliance.
Do not store flammable gas and liquid in the appliance, because they may explode.
Do not place food products directly against the air outlet on the rear wall.3)
Frozen food must not be re-frozen once it has been thawed out.
Store pre-packed frozen food in accordance with the frozen food manufacturer's instructions.
• Appliance's manufacturers storage recommendations should be strictly adhered to. Refer
to relevant instructions.
• Do not place carbonated or fizzy drinks in the freezer compartment as it creates pressure
on the container, which may cause it to explode, resulting in damage to the appliance.
• Ice lollies can cause frost burns if consumed straight from the appliance.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the mains plug from the
mains socket.
• Do not clean the appliance with metal objects.
• Do not use sharp objects to remove frost from the appliance. Use a plastic scraper.
1) If the lamp cover is foreseen.
2) If the lamp is foreseen.
3) If the appliance is Frost Free.
Control panel
• Never use a hair drier or other heating appliances to speed up defrosting. Excessive heat
may damage the plastic interior, and humidity could enter the electric system making it
For electrical connection carefully follow the instructions given in specific paragraphs.
• Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought it.
In that case retain packing.
• It is advisable to wait at least four hours before connecting the appliance to allow the oil
to flow back in the compressor.
• Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.
• Wherever possible the back of the product should be against a wall to avoid touching or
catching warm parts (compressor, condenser) to prevent possible burn.
• The appliance must not be located close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.
• Connect to potable water supply only. 4)
• Any electrical work required to do the servicing of the appliance should be carried out by
a qualified electrician or competent person.
• This product must be serviced by an authorized Service Centre, and only genuine spare
parts must be used.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The appliance shall not be discarded together
with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local
authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. The materials used on this appliance marked by the symbol are recyclable.
1 ON/OFF button
4) If a water connection is foreseen.
Control panel
2 Mode button
3 OK button
4 Temperature colder button
5 Temperature warmer button
6 Display
It is possible to change predefined sound of buttons to a loudly one by pressing together
Mode button and Temperature colder button for some seconds. Change is reversible.
3 4 5
Timer function
Minute Minder function
Child Lock function
Alarm indicator
Temperature indicator
Switching on
To switch on the appliance do these steps:
1. Connect the mains plug to the power socket.
2. Press the ON/OFF button if the display is off.
3. The alarm buzzer could operate after few seconds.
To reset the alarm refer to "High temperature alarm".
4. If "dEMo" appears on the display, the appliance is in demonstration mode. Refer to
"What to do if..." paragraph.
5. The temperature indicators show the set default temperature.
To select a different set temperature refer to "Temperature regulation".
Switching off
To switch off the appliance do these steps:
1. Press the ON/OFF button for few seconds.
2. The display switches off.
3. To disconnect the appliance from the power disconnect the mains plug from the power socket.
Temperature regulation
The set temperature of the freezer may be adjusted by pressing the temperature button.
Set default temperature:
• -18°C for the freezer
The temperature indicator shows the set temperature.
The set temperature will be reached within 24 hours.
Control panel
After a power failure the set temperature remains stored.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
The FROSTMATIC indicator flashes.
The freezer temperature indicator shows
2. Press the OK button to confirm.
The FROSTMATIC indicator is shown.
An animation starts.
This function stops automatically after 52 hours.
To switch off the function before its automatic end:
1. Press the Mode button until the FROSTMATIC indicator flashes.
2. Press the OK button to confirm.
3. The FROSTMATIC indicator goes off.
The function switches off by selecting a different freezer set temperature.
Minute Minder function
The Minute Minder function is to be used to set an acoustic alarm at the preferred time,
useful for example when a recipe requires to cool down a mixture for a certain lenght of
time, or when a reminder is needed in order not to forget the bottles placed in the freezer
for fast cooling.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
The Minute Minder indicator flashes.
The Timer shows the set value (30 minutes) for a few seconds.
2. Press the Temperature colder button or the Temperature warmer button to change the
Timer set value from 1 to 90 minutes.
3. Press the OK button to confirm.
The Minute Minder indicator is shown.
The Timer start to flash (min).
At the end of the countdown the Minute Minder indicator flashes and an audible alarm
1. Remove any drinks contained in the freezer compartment.
2. Press OK button to switch off the sound and terminate the function.
It is possible to deactivate the function at any time during the countdown:
1. Press the Mode button until the Minute Minder indicator flashes.
2. Press the OK button to confirm.
3. The Minute Minder indicator goes off.
First use
It is possible to change the time during the countdown and at the end by pressing the Temperature colder button and the Temperature warmer button.
Child Lock function
To lock the buttons from unintentional operation select the Child Lock function.
To switch on the function:
1. Press the Mode button until the corresponding icon appears.
2. The Child Lock indicator flashes.
3. Press the OK button to confirm.
The Child Lock indicator is shown.
To switch off the function:
1. Press the Mode button until the Child Lock indicator flashes.
2. Press the OK button to confirm.
3. The Child Lock indicator goes off.
High temperature alarm
Temperature increase in the freezer compartment (for example due to an earlier power failure or door is open) is indicated by:
• flashing the alarm and freezer temperature indicators
• sounding of buzzer.
To reset the alarm:
1. Press any button.
2. The buzzer switches off.
3. The freezer temperature indicator shows the highest temperature reached for a few
seconds. Then show again the set temperature.
4. The alarm indicator continue to flash until the normal conditions are restored.
Door open alarm
An acoustic alarm will sound if the door is left open for a few minutes. The door open alarm
conditions are indicated by:
• flashing alarm indicator
• acoustic buzzer.
When normal conditions are restored (door closed), the alarm will stop.
During the alarm phase, the buzzer can be switched off by pressing any button.
Cleaning the interior
Before using the appliance for the first time, wash the interior and all internal accessories
with lukewarm water and some neutral soap so as to remove the typical smell of a brandnew product, then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
Daily use
Check that the drain hose at the rear of the cabinet discharges into the drip tray.
Freezing fresh food
The freezer compartment is suitable for freezing fresh food and storing frozen and deepfrozen food for a long time.
To freeze small amount of fresh foods it is not necessary to change the present setting.
To freeze fresh food activate the FROSTMATIC function at least 24 hours before placing the
food to be frozen in the freezer compartment.
Place the fresh food to be frozen in all compartments except the bottom drawer.
The maximum amount of food that can be frozen in 24 hours is specified on the rating
plate, a label located on the inside of the appliance.
The freezing process lasts 24 hours: during this period do not add other food to be frozen.
Storage of frozen food
When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours.
The freezer baskets ensure that it is quick and easy to find the food package you want. If
large quantities of food are to be stored, remove all drawers except for the bottom basket
which needs to be in place to provide good air circulation. On all shelves except for the top
shelf it is possible to place food that protrude 15 mm from the door.
In the event of accidental defrosting, for example due to a power failure, if the power has
been off for longer that the value shown in the technical characteristics chart under "rising
time", the defrosted food must be consumed quickly or cooked immediately and then refrozen (after cooling).
Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation.
Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking
will take longer.
Helpful hints and tips
Removal of freezing baskets and glass shelves from the freezer
Some of the freezing baskets have a limit stop to
prevent their accidental removal or falling out. At
the time of its removal from the freezer, pull the
basket towards yourself and, upon reaching the
end point, remove the basket by tilting its front
At the time of putting it back, slightly lift the
front of the basket to insert it into the freezer.
Once you are over the end points, push the basket
back in their position.
The appliance is equipped with shelf stops to secure the shelves.
The shelves must be lifted up (1) on each side and
than pulled outwards (2).
Hints for freezing
To help you make the most of the freezing process, here are some important hints:
• the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating
• the freezing process takes 24 hours. No further food to be frozen should be added during
this period;
• only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
• prepare food in small portions to enable it to be rapidly and completely frozen and to
make it possible subsequently to thaw only the quantity required;
• wrap up the food in aluminium foil or polythene and make sure that the packages are
Care and cleaning
• do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a
rise in temperature of the latter;
• lean foods store better and longer than fatty ones; salt reduces the storage life of food;
• water ices, if consumed immediately after removal from the freezer compartment, can
possibly cause the skin to be freeze burnt;
• it is advisable to show the freezing in date on each individual pack to enable you to keep
tab of the storage time.
Hints for storage of frozen food
To obtain the best performance from this appliance, you should:
• make sure that the commercially frozen foodstuffs were adequately stored by the retailer;
• be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the
shortest possible time;
• not open the door frequently or leave it open longer than absolutely necessary.
• Once defrosted, food deteriorates rapidly and cannot be refrozen.
• Do not exceed the storage period indicated by the food manufacturer.
Unplug the appliance before carrying out any maintenance operation.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must
therefore only be carried out by authorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with lukewarm water and some neutral soap.
• regularly check the door seals and wipe clean to ensure they are clean and free from
• rinse and dry thoroughly.
Do not pull, move or damage any pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders, highly perfumed cleaning products or wax polishes
to clean the interior as this will damage the surface and leave a strong odour.
Clean the condenser (black grill) and the compressor at the back of the appliance with a
brush. This operation will improve the performance of the appliance and save energy consumption.
Take care of not to damage the cooling system.
When moving the cabinet, lift it by the front edge to avoid scratching the floor.
What to do if…
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the
plastics used in this appliance. For this reason use a soft cloth rinsed in warm water and
neutral soap emulsion for cleaning external surfaces.
Do not use detergents or abrasive paste as these will damage the paint, or stainless steel
anti finger print coating.
After cleaning, reconnect the equipment to the mains supply.
Cleaning the ventilation grille
The ventilation grille can be removed for washing.
Make sure the door is open and then:
1. Loosen the upper edge of the grille by
pulling outward/downward.
2. Pull the grille straight out to completely
remove it.
3. Vacuum clean under the cabinet.
Defrosting of the freezer
The freezer compartment of this model, on the other hand, is a "no frost" type. This means
that there is no buildup of frost when it is in operation, neither on the internal walls nor on
the foods.
The absence of frost is due to the continuous circulation of cold air inside the compartment, driven by an automatically controlled fan.
Periods of non-operation
When the appliance is not in use for long periods, take the following precautions:
1. disconnect the appliance from electricity supply
2. remove all food
3. clean the appliance and all accessories
4. leave the door/doors open to prevent unpleasant smells.
If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food
inside from spoiling in case of a power failure.
During operation of the appliance some smaller but annoying trouble can often occur,
which does not require calling a technician out. In the following chart information is given
about them to avoid unnecessary charges on service.
The operation of the appliance goes with certain sounds (compressor and circulating
sound). This not means a trouble, but a normal operation.
What to do if…
The appliance operates discontinuously, so the stopping of compressor does not mean being no current. That is why you must not touch the electrical parts of the appliance before
breaking the circuit.
Possible cause
The appliance is noisy.
The appliance is not supported
The buzzer sounds. The
Alarm icon flashing.
The temperature in the freezer is Refer to "HighTemperature
too high.
Check if the appliance stands stable (all feet and wheels should be
on the floor). Refer to "Levelling".
The door is not closed correctly.
Refer to "Door open alarm".
upper or lower square
is shown in the temperature display.
An error has occurred in measuring the temperature.
Call your service representative
(the cooling system will continue
to keep food products cold, but
temperature adjustment will not
be possible).
The compressor runs continuously.
The Temperature regulator may
be set incorrectly.
Set a warmer temperature.
The door is not closed correctly.
Refer to "Closing the door".
The door has been opened too
Do not keep the door open longer
than necessary.
The food temperature is too
Let the food temperature decrease to room temperature before storage.
The room temperature is too
Decrease the room temperature.
The door is not closed correctly.
Refer to "Closing the door".
The door gasket is deformed or
Refer to "Closing the door".
The temperature in the
appliance is too cold.
The Temperature regulator may
be set incorrectly.
Set a warmer temperature.
The temperature in the
appliance is too warm.
The Temperature regulator may
be set incorrectly.
Set a colder temperature.
The door is not closed correctly.
Refer to "Closing the door".
The food temperature is too
Let the food temperature decrease to room temperature before storage.
Food is too near to each other.
Store food so that there is cold
air circulation.
Large quantities of food to be
frozen were put in at the same
Insert smaller quantities of food
to be frozen at the same time.
There is too much frost
and ice.
The temperature in the
freezer is too warm.
Technical data
Possible cause
The appliance does not
The lamp does not work.
The appliance is switched off.
Switch on the appliance.
The mains plug is not connected
to the mains socket correctly.
Connect the mains plug to the
mains socket correctly.
The appliance has no power.
There is no voltage in the mains
Connect another electrical appliance to the mains socket. Check
fuse. Contact a qualified electrician.
The lamp is defective.
Refer to "Replacing the lamp".
The door has been open to long.
Close the door.
Door interferes with venti- The appliance is not levelled.
lation grill.
Refer to "Levelling".
Misaligned door.
Refer to "Levelling".
The appliance is not levelled.
As much as the advice does not lead to result, call the nearest brand-mark service.
Replacing the lamp
The appliance is equipped with a longlife LED light.
Only service is allowed to replace the lighting device. Contact your Service Center
Closing the door
Clean the door gaskets.
If necessary, adjust the door. Refer to "Installation".
If necessary, replace the defective door gaskets. Contact the Service Center.
1800 mm
1800 mm
595 mm
595 mm
623 mm
623 mm
Rising Time
12 h
12 h
230 V
230 V
50 Hz
50 Hz
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:
Climate class
Ambient temperature
+10°C to + 32°C
+16°C to + 32°C
+16°C to + 38°C
+16°C to + 43°C
To ensure best performance, if the appliance is positioned below an overhanging wall unit,
the minimum distance between the top of the cabinet and the wall unit must be at least 40
mm . Ideally, however, the appliance should not be positioned below overhanging wall
The ventilation space can be:
• directly above the appliance
• behind and above the top cupboard.
In this case, the space behind the top cupboard
must be at least 50 mm deep.
Electrical Connection
Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability should these safety measures not be observed.
The wires in the mains lead are coloured in accordance with the following code:
Green and Yellow:
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
1. Connect the wire coloured green and yellow to the terminal marked either with the
letter “E“ or by the earth symbol or coloured green and yellow.
2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or
coloured black.
3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red.
4. Check that no cut, or stray strands of wire is present and the cord clamp 4 is secure
over the outer sheath.
5. Make sure the electricity supply voltage is the same as that indicated on the appliance
rating plate.
6. Switch on the appliance.
The appliance is supplied with a 13 amp plug fitted 2 . In the event of having to change
the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used.
A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it
is disposed of safely.
Removing the transport support
Your appliance is equipped with transport support to secure the door during transportation.
To remove them do these steps:
Open the door.
Remove the transport support from the
door sides.
Remove the transport support from the
lower hinge (some models).
Some models are fitted with a silencing pad
under the cabinet. Do not remove this pad.
Rear spacers
Install the spacers provided within the accessory bag as shown in the figure.
Install the spacers on the back side of the panel.
Fitting the door handles
(Example for right hinge performance)
The handles are supplied as a kit at delivery.
1. Screw the top handle bracket to the
handle rod.
2. Fit the bottom handle bracket on the
lower left-hand side of the door.
3. Fit the top handle bracket on the top
left-hand side of the door.
4. Screw the handle rod to the bottom
handle bracket.
Do not use excessive force and overtighten
the screws (max. 2 Nm) as you may damage
the door handles.
When placing the appliance ensure that it stands
level. If necessary adjust the feet using the adjustment spanner supplied.
Door alignment is dependent on proper levelling.
Door reversibility
To change the opening direction of the door, do these steps:
1. Remove the plug from the power.
2. Remove the ventilation grille. Remove the upper filling and install it on the opposite
side of the grille.
Remove the pedal hole cover and install the cover provided in the accessory bag on
the opposite side.
3. Lay down the appliance back side down on a wooden support.
4. Remove the handle:
Unscrew the handle from the top (A1)
and the bottom (A2) of the door.
Unscrew both of the handle brackets
from the handle rod and re-screw the
handle brackets provided in the handle
Unscrew the hinge (B1) and remove the
cover plate (B2) and the support (B3).
Remove the cover (B4) on the opposite
side and install the support (B3) the
cover plate (B2) and the hinge (B1). Install the cover (B4) on the opposite side.
Unscrew the lower hinge (C1). Move the
pin to the opposite side (C2). Unscrew
and move the pedal to the opposite side
Screw on the lower hinge on the opposite side.
7. Tighten the pin with the adjustment
spanner supplied.
8. Install the handle on the opposite side.
9. Raise the appliance and install the ventilation grille.
10. Put the cabinet in position.
Reposition, level the appliance, wait for at least four hours and then connect it to the power socket.
Do a final check to make sure that:
• All screws are tightened.
• The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting of the gasket.
There are some sounds during normal running (compressor, refrigerant circulation).
Environmental concerns
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
Download PDF