AEG A72900GNW0 Freezer User Manual

User’s manual
1040
4-Line small business
system with
speakerphone
1
Congratulations
on purchasing your
new AT&T product.
Before using this AT&T product, please
read the Important product information
on pages 50-51 of this user’s manual.
Please thoroughly read the user’s
manual for all the feature operation
and troubleshooting information you
need to install and operate your new
AT&T product. You can also visit our
website at www.telephones.att.com
or call 1 (800) 222-3111.
In Canada, dial 1 (866) 288-4268.
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a
AT&T Intellectual Property licensed to Advanced American Telephones. Printed in China.
STOP!
Do you receive DSL, (Digital subscriber line,) service for highspeed internet access through your telephone line(s) from your
telephone company? If so, you will need to add either DSL
splitters and/or microfilters to your installation. See page 9 of the
installation guide.
For customer service or product information, visit our website at
www.telephones.att.com or call 1 (800) 222-3111 . In
Canada, dial 1 (866) 288-4268 .
CAUTION: To reduce the risk of fire or injury to persons or damage to
the telephone, read and follow these instructions carefully:
• Use only alkaline 9V batteries (size 1604A, purchased separately).
• Do not dispose of the battery in a fire. Like other batteries of this type,
it could explode if burned. Check with local codes for special disposal
instructions.
• Do not open or mutilate the battery. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a short circuit. Do
not allow conductive materials such as rings, bracelets, or keys to touch the
battery. The battery or conductor may overheat and cause harm.
• Use the battery identified for use with this product only in accordance with
the instructions and limitations specified in this manual.
• Observe proper polarity orientation between the battery and metallic
contacts.
• Do not disassemble your telephone. There are no user-serviceable parts
inside. Refer to qualified service personnel for servicing.
User's manual
1040
4-Line small business
system with
speakerphone
Table of contents
Getting started
Introduction..........................................................................................................................................1
Telephone Overview........................................................................................................................2
Display screen messages..............................................................................................................4
LCD CONTRAST............................................................................................................................4
Indicator lights & tones..................................................................................................................6
Indicator lights.............................................................................................................................6
Alert tones.....................................................................................................................................7
Directory card.....................................................................................................................................8
Telephone operation
Basic phone operation...................................................................................................................9
Lit line indicators........................................................................................................................9
Making and answering calls..................................................................................................9
Switching among handset, speakerphone and headset mode............................12
Timer.................................................................................................................................................12
VOLUME control..........................................................................................................................13
RINGER ON/OFF.........................................................................................................................14
RINGER TYPE................................................................................................................................14
DO NOT DISTURB.......................................................................................................................15
Last number redial.....................................................................................................................16
Redial stack...................................................................................................................................17
Auto-redial.....................................................................................................................................18
Call waiting....................................................................................................................................19
MUTE.................................................................................................................................................19
Temporary tone dialing...........................................................................................................19
HOLD.................................................................................................................................................20
Switching between lines.........................................................................................................21
Call privacy....................................................................................................................................21
Conference calls.........................................................................................................................22
Transfer a call...............................................................................................................................23
Blind transfer................................................................................................................................23
Transfer a call and speak to the receiving party........................................................24
Answer a transferred call.......................................................................................................24
i
Intercom operation
Intercom overview............................................................................................................................25
Intercom ...............................................................................................................................................26
Make an intercom call with the handset........................................................................26
Make an intercom call with the speakerphone or headset...................................27
Answer an intercom call.........................................................................................................28
End an intercom or page call...............................................................................................28
Voice page............................................................................................................................................29
Page a specific extension (single-phone page)...........................................................29
Answer a single-phone page................................................................................................30
Page all (system-wide page)................................................................................................31
Answer a system-wide page.................................................................................................32
Room monitor..............................................................................................................................33
Make an intercom conference call....................................................................................33
One-touch setup and operation
One-touch overview........................................................................................................................34
One-touch.............................................................................................................................................35
PREFERENCE.................................................................................................................................35
One-touch storage...........................................................................................................................36
To dial a one-touch number........................................................................................................38
To view or delete a one-touch number.................................................................................39
To view a one-touch number...............................................................................................39
To delete a one-touch number............................................................................................39
To modify a one-touch number.................................................................................................40
Using a 1080 mailbox
Forwarding to DTAD mailbox.......................................................................................................42
To setup call forwarding................................................................................................................43
To turn call forwarding on.....................................................................................................43
To set call forwarding delay time.......................................................................................43
Listening to messages - internal access...............................................................................44
Appendix A, Glossary...............................................................................................................45
Appendix B, Time/date .........................................................................................................46
Appendix C, Centrex operation...........................................................................................47
Set ring delay duration..............................................................................................................47
Answer a delayed ring...............................................................................................................47
Pick up another station’s line.................................................................................................47
Centrex service call example..................................................................................................48
Appendix D, General product care....................................................................................49
ii
Appendix E, Important product information.................................................................50
Safety information........................................................................................................................50
Especially about corded telephones...................................................................................51
Especially about telephone answering systems............................................................51
Appendix F, FCC and ACTA information..........................................................................52
Appendix G, Part 15 of FCC rules......................................................................................54
Appendix H, Limited warranty..............................................................................................55
Appendix I, Technical specification....................................................................................58
Appendix J, In case of difficulty..........................................................................................59
Index....................................................................................................................................................66
iii
Getting started
Introduction
This AT&T Small Business System is expandable to a 16-extension telephone
system. The 1040 telephone is compatible with 1070 and 1080 telephones.
For details, see the Installation Guide. This system is not compatible with any
other AT&T 4-line small business telephones, except for the 1070 and 1080
telephones.
The 1040 telephone is hearing-aid compatible and can be connected to up
to four incoming telephone lines. This telephone features a speakerphone
for handsfree use and a headset jack compatible with most two-band 2.5mm
headsets (sold separately). There are two additional ports available for
connecting the telephone to another device such as a fax machine or modem.
The 1040 allows paging, intercom and call transfers between system telephones
and is capable of connecting three parties in the same conference call.
This telephone also features a 32-number one- and two-touch memory for
faster dialing.
If there is a 1080 telephone in your system that is an auto attendant, it may
record messages for your set.
The 1040 telephone is compatible with Centrex service. Centrex is a special
subscriber service which may be available from your local telephone company
for a fee. If you subscribe to Centrex service, refer to the Centrex operation
section (page 47).
This user's manual contains detailed instructions for using your AT&T Small
Business System 1040 telephone. Please read this manual before using this
1040 telephone.
Getting started
Telephone overview
LINE BUTTONS, 1-4
Press to make or answer a call on the desired line (page 9).
While on a call, press to release the call privacy feature
(page 21).
TRANSFER
Press to transfer
an outside call to
another 1040, or
a 1070, or a 1080
(page 48).
DO NOT DISTURB
Press twice to
activate the Do
Not Disturb feature
(page 40).
Press again to
resume normal use
(page 40).
HEADSET JACK
(Beneath the small
rubber flap,) for
2.5mm headset
FLASH
During a call, press to receive
an incoming call if call waiting
service is activated (page 19).
(AUTO) REDIAL
Press to view the
redial stack (page
18).
Press again to quit.
Getting started
Telephone overview
One-touch keys
Press to make an
intercom call (page
26) or a one-touch
outside call (page 38).
Navigation keys
Press to scroll up, down,
left or right while in
the menu.
VOLUME
While the telephone
is not in use, press to
adjust ringer volume
(page 13).
During a call, press
to adjust listening
volume (page 13).
ENTER
Press until you see the
main menu. Once in the
menu, press to select
an item or save an entry
or setting.
Press and hold to exit
the menu.
HOLD
Press to place an outside call on hold (page
20).
HEADSET
Press to turn on the
headset (page 11).
MUTE
Press so that the
other party cannot
hear you.
Press again to resume
the conversation
(page 19).
CONFERENCE
Press to create a
three-way conversation (page 22).
INTERCOM
Press to intercom or
page another extension
(pages 26-29).
LOWER
Press to dial a telephone number stored
in the lower location
of a one-touch key
(page 38).
SPEAKER
Press to turn on the
speakerphone. Press
again to turn off
(page 10).
Getting started
Display screen messages
LCD contrast
SPECIAL OPTIONS
LEVEL-4
LCD CONTRAST
Your set's display provides important information.
You can adjust the screen contrast to one of eight
levels to optimize readability in different lighting
conditions.
1.Press [ENTER].
2. Press [ ] or [ ] until you see SPECIAL OPTIONS.
Press [ENTER].
3.Press [ ] or [ ] until you see LCD CONTRAST.
4.Press [ ] or [ ] to select the screen contrast
level (1-8).
5.To move to the next feature, press [ ].
-OR To exit setup, press and hold [ENTER].
AC FAIL
There is no AC power to the set. If a good battery
is installed, basic phone operation is supported,
(such as making and answering calls on the
handset.) Speakerphone, headset and call privacy
are not supported. The handset volume will be at
the minimum level and only the two lowest levels
will be available for the ringer volume.
DND
The Do Not Disturb mode is on.
DTAD: XX/YY
Flashes when the mailboxes of the DTAD mailbox
1080 telephone are full or when the auto
attendant of the DTAD mailbox 1080 telephone
is off. (XX is the total number of new system
extension messages recorded for this 1040
telephone. YY is the total number of all system
extension messages recorded for this 1040
telephone.)
(EMPTY)
The one-touch location is empty.
EXT XX RING
There is an incoming Centrex call.
continued on next page
Getting started
Display screen messages
continued from previous page
INITIALIZING. .
The telephone is warming up.
INTERCOM FROM XX
Another system telephone XX is calling (XX is the
extension number).
LIST EMPTY
The redial memory is empty.
LOW BATT
There is no spare battery in the telephone or the
battery power is low.
LOWER
The [LOWER] key is pressed for the lower section
of a one-touch key.
PAGE FROM XX
The telephone is on a single page call with
another system telephone XX (XX is the extension
number).
PAGE ALL FROM XX
[ENTER]: ANSWER
The telephone is on a system-wide page call with
another system telephone XX (XX is the extension
number).
SAVED !
The entry was saved to the one-touch location
successfully.
TRANSFER FROM XX
There is an incoming call transferred from another
system telephone XX (XX is the extension number)
or the auto attendant system.
Getting started
Indicator lights & tones
Indicator lights
LINE
Green:
• On when the line is in use.
• Flashing slowly when the line is on hold.
• Flashes quickly when a person has transferred a
call on that line.
• Flashes quickly when there is an incoming auto
attendant transferred call on the line.
• Flashes rapidly when there is an incoming call.
Red:
• On when another telephone in the system is using
the line.
• Flashes slowly when the line is on hold by
another telephone in the system.
(AUTO) REDIAL
When auto-redial is active:
• Flashes when the telephone is dialing the desired
number.
• On between dialing attempts.
DO NOT DISTURB
• ������������
On when the Do Not Disturb function is on.
continued on next page
Getting started
Indicator lights & tones
continued from previous page
NEW MSG
• Flashes when there are new system extension messages. The screen will display ”DTAD: XX/YY”, with “YY” greater than zero.”
INTERCOM
• On when the telephone is on an intercom call or a
paged call.
• On when the system is busy and the intercom is unavailable.
• Flashes during an incoming intercom call’s ringing.
HEADSET
• On when the headset is in use.
• Flashes when there is an auto-redial call with the
headset.
MUTE
• On when the microphone is muted.
SPEAKER
• On when the speakerphone is in use.
• Flashes when there is an auto-redial call with the
speakerphone.
Alert tones
Confirmation tone
Programming command completed successfully.
One double-beep
every 30 seconds
When the hold reminder feature is on and there
is a line on hold.
A triple-beep
During volume adjustment, the volume level is
at the maximum or minimum.
Getting started
Directory card
To write names and/or phone numbers on the directory card, follow the steps
below:
1.Remove the clear plastic cover by inserting a small item such as paperclip
into the hole on the lower right corner.
2.Pull out the directory card.
3.Write the information on the directory card.
4.Replace the directory card and then the plastic cover.
MSG
MSG
MSG
MSG
MSG
MSG
NOTE: There is a replacement directory card in the telephone package. You
can use it to replace the current one on the telephone if necessary.
Telephone operation
Basic phone operation
This phone comes programmed to use line 1
(default prime line) for calls if you do not press a
line button. (To change the prime line, see Prime
line on page 39 of the installation guide.) When
you answer a call, the phone automatically selects
the ringing line.
Lit line indicators
The four indicators above the [LINE] keys will
indicate the state of the corresponding phone line.
The four LINE lights have two colors:
• Green is for outside calls.
a. On when the line is in use on this phone.
b. Flashes slowly when the line is on hold.
c. Flashes rapidly when there is a transferred
call on the line.
d. Flashes quickly when there is an incoming
auto attendant transferred call on the line.
•
e. Flashes rapidly when there is an incoming
call on that line.
Red is for the state of the phone system.
a. On when another phone is using the line.
b. Flashes slowly when the line is held by
another phone on the same system.
Making and answering calls
This phone will automatically make and answer
calls in the mode (speakerphone or headset) you
programmed (see automatic mode on page
39 of the installation guide). Follow the direction
below to choose a mode manually. If the phone
is in use on one line, any other calls made or
answered will use the same mode already in use.
continued on next page
Telephone operation
Basic phone operation
continued from previous page
Handset
To make a call:
1. Lift the handset.
2. Dial a number.
• To override automatic line selection, press the
LINE button for the line you wish to select, then
lift the handset.
• To answer a call, lift the handset.
• To hang up, place the handset on the base.
•
Speakerphone
To make a call:
1. Press and release the desired LINE button or
[ SPEAKER]. The SPEAKER light goes on.
2. Wait for a dial tone, then dial the number.
• To answer a call, press [ SPEAKER] or press
the LINE button of the incoming call.
• To end the call, press [ SPEAKER].
•
NOTES:
• If SPEAKERPHONE is selected in the AUTOMATIC
MODE menu (page 39 of the installation guide),
pressing any line key will select the line and activate the speakerphone. If HEADSET is selected in
the AUTOMATIC MODE menu and a headset is
connected, pressing any LINE key will select the
line and activate the headset.
• If headset is programmed as the default mode,
you must press [ SPEAKER]. to activate the
speakerphone.
continued on next page
10
Telephone operation
Basic phone operation
continued from previous page
Headset (purchased separately)
You can use this phone hands-free when you
install any industry-standard two-band 2.5mm
headset or other compatible, electronically
isolated headset. The headsets must be purchased
separately.
•
•
•
To make a call:
1. Press [HEADSET] (if a headset is connected to the telephone base).
2. Wait for a dial tone, then dial the number.
To answer a call, press [HEADSET].
To hang up, press [HEADSET].
Make sure the headset is plugged into the
headset jack. You will hear a triple-beep if
you press [HEADSET] when the headset is not
plugged in.
NOTE: If SPEAKERPHONE is selected in the
AUTOMATIC MODE menu (page 39 of the installation
guide), pressing any line key will select the line and
activate the speakerphone. If HEADSET is selected
in the AUTOMATIC MODE menu and a headset is
connected, pressing any [LINE] key will select the
line and activate the headset.
11
Telephone operation
Basic phone operation
Switching among handset, speakerphone and
headset mode
To switch from handset to headset or
speakerphone, press [HEADSET] or [ SPEAKER],
then replace the handset. (In order to use the
headset, it must be plugged in.)
To switch from speakerphone to handset, lift the
handset. (Do not press [ SPEAKER] or the call
will be disconnected.)
To switch from speakerphone to headset, insert
the headset plug into the jack on the side of the
telephone base, and press [HEADSET].
To switch from headset to handset when
the handset is in the telephone base, lift the
handset.
To switch from headset to handset when the
handset is off-hook, press [HEADSET] again.
To switch from headset to speakerphone, press
[ SPEAKER].
To override automatic line selection, press
and release a line button. This activates
the speakerphone or headset, whichever is
programmed as the default mode.
Timer
10:01AM
00:30
5550100
11/23
When you make or answer a call, the timer
automatically starts. The screen displays the
elapsed time in minutes and seconds for the
first hour (up to 59:59) and then begins again.
The timer stops automatically when you hang up
and the recorded time is displayed for about 10
seconds. The timer also stops when you place a
call on hold and resets to 00:00 when you release
the hold.
12
Telephone operation
Basic phone operation
Volume control
The volume keys control the level of the incoming
voice as well as the ringer volume.
Handset/speakerphone/headset volume
• While using the handset, press [ VOLUME] to
adjust the listening volume (1-5).
• While using the speakerphone, press [ VOLUME]
to adjust the listening volume (1-8).
• While using the headset, press [ VOLUME] to
adjust the listening volume (1-5).
While using the volume control, you will hear
a triple-beep when you reach the minimum or
maximum level.
Your 1040 remembers the volume setting for each
mode.
Ringer volume
• When the telephone is idle, press [ VOLUME] to
sample and select the desired volume (1-4) for
all ringers. When changing the volume, the new
setting is saved.
• While the phone is ringing, press [ VOLUME] to
adjust the ringer volume (1-4). As you adjust the
ringer, you will hear the change in volume.
NOTE: You can turn the external ringer off separately for each line (page 14).
13
Telephone operation
Basic phone operation
Ringer on/off
RINGER ON/OFF
ON
L1 RINGER
This feature controls whether there is an audible
alert for outside calls on the designated line.
1.Press [ENTER].
2.Press [ ] or [ ] until you see PHONE SETTINGS.
Press [ENTER].
3.Press [ ] or [ ] until you see RINGER ON/OFF.
Press [ENTER].
4.Press [ ] or [ ] to select the desired line
(L1 RINGER, L2 RINGER, L3 RINGER or L4
RINGER).
5.Press [ ] or [ ] to turn the ringer ON or OFF.
ON is the default setting.
6.To move to the next line, press [ ].
-OR To exit setup, press and hold [ENTER].
Ringer type
RINGER TYPE
TYPE 1
L1 RINGER TYPE
Use this feature to choose one of the four ringer
types for incoming calls. You can choose different
ringer types for the different lines so you can
easily identify which line is ringing.
1.Press [ENTER].
2.Press [ ] or [ ] until you see PHONE
SETTINGS. Press [ENTER].
3.Press [ ] or [ ] until you see RINGER TYPE.
Press [ENTER].
4.Press [ ] or [ ] to highlight the desired
line (L1 RINGER TYPE, L2 RINGER TYPE, L3
RINGER TYPE or L4 RINGER TYPE).
5.Press [ ] or [ ] to highlight the desired ringer
type (TYPE 1, TYPE 2, TYPE 3 or TYPE 4).
6.To move to the next line, press [ ].
-OR To exit setup, press and hold [ENTER].
14
Telephone operation
Basic phone operation
DO NOT DISTURB
When you activate the do not disturb (DND)
function, you will not hear paging tones, voice
paging, or incoming call rings.
Instead, the LINE light flashes to signal an
incoming call. If you receive an intercom call, the
[INTERCOM] light flashes, and the number of the
incoming intercom call appears on the display.
1. Press [DO NOT DISTURB] twice to prevent
interruptions. The DO NOT DISTURB light goes on
and the screen includes DND.
2. Press [DO NOT DISTURB] again to resume
normal call alerts. The DO NOT DISTURB light
goes off and the screen no longer shows DND.
Callers will hear very long beeps, the same tone
as if the system phone is ringing normally.
15
Telephone operation
Basic phone operation
Last number redial
The last number dialed from this extension (up to
32 digits) is stored in the redial memory until you
dial another number. Press [(AUTO) REDIAL] you
will see the most recently dialed number (up to 32
digits).
• You must go off hook (lift the handset or press
a [LINE] button or press [ SPEAKER] or
[HEADSET]) before you press [(AUTO) REDIAL].
If you press [(AUTO) REDIAL] without going
off hook, the screen displays the redial memory
stack. (See Redial stack on page 17.)
• You will experience a one-second delay before
the call is dialed when using the redial feature.
This is normal.
See Redial stack on the next page to learn how
to delete redial numbers and store them into
memory locations.
16
Telephone operation
Basic phone operation
Redial stack
The last six numbers dialed from this extension
are automatically stored in the redial memory
stack. You can review the numbers in the redial
memory and dial one if you wish.
NOTE: If the desired
redial number is longer
than 16 digits, the screen
will only display the first
14 digits.
1.When the phone is idle, press [(AUTO) REDIAL].
2. Press [ ] or [ ] to scroll through the last six
numbers dialed at this extension.
3.When the desired number is displayed, press
[ENTER] twice to dial the call.
-OR Pick up the handset to dial the call.
NOTE: While reviewing the numbers in the redial
stack, if you want to place a new call other than
the displayed number, you need to press and hold
[ENTER] or wait for 30 seconds to return to idle.
• To delete a redial number:
1. While the redial number is displayed, press [ENTER].
2. Press [ ] or [ ] to highlight REMOVE.
3. Press [ENTER] to delete the number. Once deleted, the entry cannot be retrieved.
• To store a redial number in a one-touch key:
1.While the number is displayed, press
[ENTER].
2. Press [ ] or [ ] until you see COPY TO 1TOUCH. Press [ENTER].
3. Press a one-touch key or press [LOWER], then
a one-touch key (page 36).
• To exit, press [(AUTO) REDIAL].
17
Telephone operation
Basic phone operation
Auto-redial
This phone can automatically redial a number
every 60 seconds up to ten times. When the
phone automatically redials the number, it always
uses the line you originally used to dial the call.
1. Follow the instructions under Redial stack,
(page 17), to find the number you want to call.
NOTES:
• When the telephone automatically redials, it
always uses the prime
line.
• While reviewing the
numbers in the redial
stack, if you want to
place a new call other
than the displayed
number, you need
to press and hold
[ENTER] or wait for
30 seconds to return
to idle.
• Within the 30-second
auto redialing period,
you must lift the
handset, or press
[ SPEAKER] or
[HEADSET] if you
want to stay in the
call, otherwise, the
line will hang up and
redial again.
• During these 30
seconds, if you want
to end the autoredial attempts, press
[ SPEAKER] twice
(or [HEADSET] twice
if the headset is
being used).
2. Press a [LINE] button.
-OR Press [ SPEAKER] or [HEADSET].
-OR Press [ENTER]. Scroll to AUTO REDIAL and
then press [ENTER] again.
3.When the other line rings or the other party
answers, to speak with the other party, lift the
handset.
-OR Press [ SPEAKER].
-OR Press [HEADSET] if the headset is connected to
speak with the other party.
While auto-redial is active:
• The telephone will activate the speakerphone
or headset (depending on the AUTOMATIC MODE
you set, page 39 of the installation guide) and
call the desired number automatically. The
[(AUTO) REDIAL] light will flash.
• If the line is busy, there is a busy tone lasting for
approximately 20-25 seconds before hanging
up. After another 30 seconds, the call will be
redialed again. The [(AUTO) REDIAL] light will
remain on.
NOTE: During these 30 seconds, if you want
to stop the auto-redial feature, press [(AUTO)
REDIAL].
This process will be repeated up to 10 times or until
the called number is free to accept calls. If the line
is still busy after 10 attempts, no more attempts
will be made.
18
Telephone operation
Basic phone operation
Call waiting
If you subscribe to call waiting service with your
local telephone company, there will be a beep if
there is an incoming call when you are already on
a call on the same line.
1.Press [FLASH] to put your current call on hold
and take the new call.
2.Press [FLASH] anytime to switch back and forth
between calls.
MUTE
During a telephone conversation, press [MUTE] to
silence the microphone. You will be able to hear the
other party, but the other party will not be able to
hear you until you press [MUTE] again and resume
speaking. Mute is automatically cancelled when you
end a call.
When mute is active, the MUTE light will be on.
NOTE: Switching from handset to speakerphone
or headset, or from speakerphone or headset to
handset, changing lines, and putting a call on hold
also cancel the mute function.
Temporary tone dialing
If you have dial pulse (rotary) service only, you can
temporarily switch dial pulse to touch-tone dialing
during a call by pressing [*TONE].
1.Dial the number.
2. Press and release [*TONE]. Buttons pressed after
this send touch-tone signals.
3.After you hang up, the phone automatically
returns to pulse dial mode.
19
Telephone operation
Basic phone operation
HOLD
You can use the hold feature to hold one
line while acessing another, or as part of the
conference and call transfer features.
While on a call, press and release [HOLD]. The
LINE light for the line on hold flashes slowly
in green, and a double-beep sounds every 30
seconds to remind you that the call is on hold. (To
turn off the reminder beep, see HOLD REMINDER
on page 36 of the installation guide.)
If you were using the handset, you can place
the handset in the telephone base without
disconnecting the call. If you were using the
speakerphone, the speakerphone is automatically
turned off when you press [HOLD].
To release the hold, press and release the [LINE]
button of the call on hold.
NOTES:
• The phone automatically disconnects a call on
hold after 20 minutes. To keep a call on hold longer than 20 minutes, release hold within 20 minutes and then place the call on hold again.
• You cannot put an intercom call on hold.
• If a line is in use, pressing [INTERCOM] will place
the line on hold and activate the intercom (page
26).
20
Telephone operation
Basic phone operation
Switching between lines
During an outside call:
1.Press and release [HOLD] to maintain the
connection to the call on the active line.
2.Press and release the LINE button of another
line to make or answer another call.
3.To return to the first call, press [HOLD] to put
the current call on hold. Then press the [LINE]
button of the original line.
Call privacy
To ensure call privacy, this phone allows only one
set at a time to use a line.
Cancel call privacy
During the call, press the [LINE] button for the
call. You’ll hear a short beep. Others can now join
the call by pressing the appropriate line button.
Restore call privacy
Press the [LINE] button again during the call.
You’ll hear a double-beep. The other phones will
be dropped from the call.
NOTES:
•
Call privacy is automatically restored when you
end the call.
•
When a non-system phone answers a call,
any other system phone can pick up the call
by pressing the [LINE] button. Once a system
phone picks up the call, call privacy is activated
and no other system phones can listen to the
call unless call privacy is canceled, but non-system phones which share that line can still join
the call.
21
Telephone operation
Basic phone operation
Conference calls
This feature lets you set up a three-party call by
using two lines at the same time. You can also
join an intercom call with a call on an outside
line. The outside line call must be established first
because an intercom call cannot be placed on
hold.
NOTES:
Occasionally, the farend parties on a
conference call might
not hear one another.
• If you are experiencing
difficulty in using the
conference features
on this phone, please
consider using
AT&T’s complete line of
teleconference services
to find a solution that
best meets your needs.
AT&T TeleConference
Services reduces travel
time and expense
while increasing
productivity wherever
people are located
allowing you to host
truly virtual meetings
and share important
information in real
time. To sign up for
AT&T TeleConference
Services, go to:
•
www.att.com/
orderconference
1. Make or answer an outside call.
2. Press and release [HOLD].
3. Call someone on another line, or intercom someone.
4. When this call is answered, press [CONFERENCE]. The three-party conference begins immediately.
To talk privately with one party (two-line
conference only):
1. Press [HOLD] to place both lines on hold.
2. Press a [LINE] button to talk privately with the person on that line.
3. Press [CONFERENCE] to resume the conference call.
To drop one line:
Press the [LINE] button of the party you want to
keep. The other line will be dropped.
To drop an extension:
Press the [LINE] button twice. The other system
extension will hang up.
To end a two-line conference call, hang up. All
parties will disconnect.
To end a two-extension conference call, hang
up on both system extensions. All parties will
disconnect.
for details.
22
Telephone operation
Call transfer
Transfer a call
You can transfer a call to any other system phone.
Once you transfer a call, it can be picked up at
any other system phone, not just at the extension
you called.
NOTE��: If a transferred call is not picked up
within 20 minutes, the phone will automatically
disconnect the call.
Blind transfer
While on a call:
10:01AM
00:30
11/23
10:01AM
11/23
00:30
TRANSFER LINE#1
TO
10:01AM
11/23
EXT 11
TRANSFER LINE #1
TO 12
1.Press [TRANSFER]. The outside call will
automatically be put on hold. You will see
TRANSFER LINE#Y TO (with Y being the line in
use) on the third line of the display.
2.Press the one-touch button for the destination
extension for the call.
-ORDial the destination extension number to which
you’re transferring the call. You will see the
extension number in the fourth line of the
display.
3.Hang up.
Your phone reminds you with a double-beep every
30 seconds when a transferred call has not been
answered (To turn off the reminder beep, see
HOLD REMINDER on page 36 of the installation
guide).
NOTE�: If you do not dial an extension
within 10 seconds, the transfer is automatically
canceled. The call is still on hold. Press the
corresponding LINE key to resume the call.
23
Telephone operation
Call transfer
Transfer a call and speak to the receiving party
10:01AM
00:30
11/23
10:01AM
11/23
EXT 11
INTERCOM TO
PAGE
While on a call:
1. Press [INTERCOM]. The outside call will
automatically be put on hold, and you will see
INTERCOM TO XX, with XX being the destination
extension number.
2. Press the one-touch button for the extension to
which you’re transferring the call.
-OR-
10:01AM
11/23
EXT 11
INTERCOM TO 12
Dial the extension number to which you’re
transferring the call. You will see the extension
number in the third line of the display.
3. When the other party answers by pressing
[INTERCOM], you can announce the call.
4. Press [TRANSFER].
5. Hang up.
10:01AM
11/23
EXT 11
TRANSFER LINE #1
TO 12
10:01AM
11/23
EXT 12
TRANSFER FROM 11
NOTE�: If you do not dial an extension
within 10 seconds, the transfer is automatically
canceled. The call is still on hold. Press the
corresponding LINE key to resume the call.
Answer a transferred call
When you hear a long transfer ring, pick up the
handset or press the [LINE] button of the call to
use the speakerphone or headset.
24
Intercom operation
Intercom overview
This 1040 telephone is fully compatible with any AT&T Four-Line Small
Business System Speakerphone 1070 or 1080 phones you may have installed.
You can use a total of 16 1080/1070/1040 phones together as extensions in
your phone system.
Each individual phone in your telephone system MUST be assigned a unique
extension number for the intercom feature to work. See EXTENSION NUMBER
on page 32 of the installation guide for instructions.
This intercom features both a single-phone page and a system-wide page
(PAGE ALL).
A single-phone page alerts only one phone. A system-wide page (PAGE ALL)
alerts all system phones. Any phone with the Do Not Disturb (DND) feature
activated will not receive a page.
An intercom call rings at the destination extension with a repeating double-ring
pattern.
A single-phone page automatically activates the speakerphone on the receiving
phone. You can deactivate the speakerphone by lifting the handset.
NOTE: If a line is in use, pressing [INTERCOM] will place the line on hold
and activate the intercom (page 26).
Basic intercom operations
Operation:
Function:
INTERCOM
Lets any two extensions connected to line 1 ring
each other (page 26).
PAGE
Lets you announce over the speaker of the
destination phone (page 29).
PAGE ALL
Lets you announce to all phones in the system at
the same time (system-wide page) (page 31).
CONFERENCE
Lets you connect an intercom call with an
outside line (page 22).
25
Intercom operation
Intercom
Use this feature for calls between system phones.
Make an intercom call with the handset
10:01AM
11/23
EXT 11
INTERCOM TO
PAGE
10:01AM
11/23
EXT 11
INTERCOM TO 12
1.If One-touch preference is set to INTERCOM
(page 35), skip to step 2.
-OR If One-touch preference is set to TELEPHONE
(page 30 of the installation guide), press
[INTERCOM].
2.Press the one-touch button for the destination
party, then lift the handset. The screen will diplay
INTERCOM TO XX, with XX being the destination
extension number.
If the extension you called is idle or set to Do
Not Disturb, you will hear long beeps. If the other
extension is on a call, you will hear a busy signal.
NOTE: The intercom call is automatically canceled if you do not press a one-touch button within 10 seconds.
26
Intercom operation
Intercom
Make an intercom call with the speakerphone or
headset
10:01AM
11/23
EXT 11
INTERCOM TO
PAGE
10:01AM
11/23
EXT 11
INTERCOM TO 12
With the handset in the telephone base:
1. If One-touch preference is set to INTERCOM, skip
to step 2.
-OR If One-touch preference is set to TELEPHONE,
press [INTERCOM]. The phone will
automatically activate the intercom call in
the mode (headset or speakerphone) you
programmed (see AUTOMATIC MODE on page
39 of the installation guide).
2. Press the one-touch button. The screen will
display INTERCOM TO XX, with XX being the
destination extension.
If the extension is idle or set to Do Not Disturb,
you will hear long beeps. If the other extension is
busy, you will hear a busy signal.
NOTE: The intercom call is automatically canceled if you do not press a one-touch button within 10 seconds.
27
Intercom operation
Intercom
Answer an intercom call
10:01AM
11/23
EXT 12
INTERCOM FROM 11
When you receive an intercom call, you will hear a
repeating double-ring pattern and your screen will
display INTERCOM FROM with the extension number
of the caller. Answer the intercom call by lifting the
handset, or by pressing [INTERCOM], [ SPEAKER]
or [HEADSET] to take the call hands-free.
NOTE: If you press [INTERCOM] to answer the
call, the phone will automatically use the mode
(speakerphone or headset) you programmed as the
automatic mode (see AUTOMATIC MODE on page
39 of the installation guide).
End an intercom or page call
To end the intercom or page call, press [INTERCOM].
-ORHang up or press [ SPEAKER] or [HEADSET]
again.
28
Intercom operation
Voice page
Page a specific extension (single-phone page)
Sends your voice to the speaker of the destination
phone. The person you’ve called may be able to
respond just by talking. See AUTO MUTE on page 35
of the installation guide.
10:01AM
11/23
EXT 11
INTERCOM TO
PAGE
10:01AM
EXT 11
PAGING
INTERCOM
11/23
10:01AM
EXT 11
PAGE 12
11/23
1.Press [INTERCOM].
2.Press [ENTER] to select PAGE.
3.Enter the destination extension number (11-26).
4. Your telephone will display PAGE and the called
extension number. Now the speakerphone on the
destination telephone is activated automatically.
To end the page:
• Press [INTERCOM] on either telephone.
NOTES:
• Refer to page 32 of the installation guide to get
more information on extension numbers.
• Pressing [INTERCOM] while on an external call
will initiate a call transfer (page 24).
• If the destination telephone is in the Do Not
Disturb mode, on an intercom call or on an
outside call, your telephone will sound a busy
signal.
• The auto-mute feature may be set to ON on the
destination telephone to protect privacy (page
35 of the installation guide). The person at the
destination extension will have to press [MUTE] to
re-activate the microphone (page 19).
29
Intercom operation
Voice page
Answer a single-phone page
10:01AM
11/23
EXT 12
PAGE FROM 11
Auto-mute off
When your extension receives a page, the phone
beeps and the speakerphone is automatically
activated. Answer the call simply by speaking.
If you are on the headset, you can answer the
page by pressing [HEADSET] and speaking
through the the microphone of the headset.
Auto-mute on
The [MUTE] light will be on. Lift the handset or
press [MUTE] to temporarily de-activate automute and answer the page.
30
Intercom operation
Voice page
Page all (system-wide page)
...
Sends your voice to the speakers of all phones in
the system.
1. Press [INTERCOM] then [ ] to show PAGE ALL.
2. Press [ENTER]. The screen will display PAGE ALL.
Once the page is automatically answered, speak
and your voice will be heard at all idle extensions
in your phone system.
10:01AM
11/23
EXT 11
INTERCOM TO
PAGE ALL
10:01AM
EXT 11
PAGE ALL
11/23
Page-all shortcut
1.Press [INTERCOM], then press [#].
2. Your telephone will display PAGE ALL. You will be
heard at all idle extensions.
NOTES:
• Pressing [INTERCOM] while on an external call
will initiate a call transfer (page 24).
• If a system telephone is in the Do Not Disturb
(DND) mode, on an external or intercom call,
the system-wide page will not be heard there.
• During a page all, the people at all extensions will
be able to hear you, but you are not able to hear
them.
• During a page all, if [ENTER] is pressed on any
system telephone, the system-wide page will be
terminated and the person on that telephone will
join the intercom call with you.
To end the page all:
• Press [INTERCOM] on your telephone.
31
Intercom operation
Voice page
Answer a system-wide page
10:01AM
11/23
EXT 12
PAGE ALL FROM 11
[ENTER]: ANSWER
10:01AM
11/23
EXT 12
INTERCOM FROM 11
NOTE: Only one extension can answer a systemwide page.
When you receive a system-wide page, your
phone beeps and the screen shows PAGE ALL
FROM XX, with XX being the originating extension
number.
1. Press [ENTER] to answer the page. The screen
displays INTERCOM FROM XX, where XX is the
calling extension number.
2. Press [INTERCOM] to end the call on either
telephone.
32
Intercom operation
Voice page
Room monitor
10:01AM
EXT 11
PAGING
INTERCOM
11/23
10:01AM
EXT 11
PAGE 12
11/23
Make a single-page call to a system phone to
monitor the sounds from that room. To use the room
monitor feature, the destination telephone automute feature must be turned off (page 35 of the
installation guide).
1. Press [INTERCOM].
2. Press [ENTER] to select PAGE.
3. Enter the destination extension number (20).
4. After your telephone displays PAGE XX, press [MUTE]. The destination telephone will beep, then activate its speakerphone automatically. Now, you can monitor the room of the destination telephone without being heard.
To end room monitoring, press [INTERCOM] on
your telephone.
Make an intercom conference call
Someone at a system phone having a twoway conversation on an outside line can invite
someone at an extension to join the conversation.
Follow the directions under Conference calls
on page 22, making sure to establish the nonintercom call first.
NOTE: ��������������������������������������
You cannot put an intercom conference
call on hold.
33
One-touch setup and operation
One-touch overview
NOTE: The onetouch buttons are also
used to place intercom
calls. See Intercom
operation beginning
on page 25 for details.
This telephone has 32 one-touch locations
(speed dial locations) where you can store phone
numbers you wish to dial using fewer keys than
usual. You can store up to 24 digits in each
location. The steps used to dial numbers stored
in one-touch locations vary according to how
you programmed the one-touch preference. See
PREFERENCE on page 35 and To dial a onetouch number on page 38 for more details.
The first 16 locations can be accessed using only
the one-touch buttons. To access the remaining
16 locations, press [LOWER] and then the onetouch button for the desired location.
You may wish to write the names or telephone
numbers of the one-touch entries on the directory
card, using the light gray spaces for the first 16
locations and the dark gray spaces for the second
16 locations (page 16 of the installation guide).
one-touch buttons
16 one-touch locations
(all light gray spaces)
16 lower one-touch
locations
(all dark gray spaces)
34
One-touch setup and operation
One touch
Assign the buttons on the right side of the phone,
the one-touch keys, as intercom or outside call
shortcut keys, and enter and view the outside
phone numbers.
ONE TOUCH
Preference
TELEPHONE
PREFERENCE
Assign the one-touch keys as intercom or outsidecall shortcut keys.
1. Press [ENTER].
2. Press [ENTER] again to enter the ONE TOUCH
menu.
3. Press [ ] or [ ] until you see PREFERENCE.
4. Press [ ] or [ ] to highlight INTERCOM or
TELEPHONE. INTERCOM is the default setting.
5. To move to the next feature, press [ ].
-OR To exit setup, press and hold [ENTER].
35
One-touch setup and operation
One-touch storage
PROGRAM
(ENTER NUMBER)
PAUSE
1. Press [ENTER]. The screen displays ONE TOUCH.
2. Press [ENTER].
3. Press [ ] or [ ] repeatedly until you see
PROGRAM.
4. Press [ENTER]. The screen includes (ENTER
NUMBER).
5. Use the dial pad to enter up to 24 digits.
-OR•To copy the most recently dialed number
from redial, press [(AUTO) REDIAL]. Only the
last number dialed from this extension can
be copied to a one-touch location. The other
numbers on the redial list cannot be copied.
•If you need to store a two-second dialing
pause for accessing banking or long distance
services, press [ ] or [ ], scroll to PAUSE,
then press [ENTER]. A P will appear on the
screen.
•If you need to store a signal for switching to
temporary tone dialing, press [ ] or [ ] until
you see TONE, then press [ENTER]. A T will
appear on the screen.
•If you need to store a flash signal for
using the service supplied by your telephone
company, press [ ] or [ ] until you see
FLASH, then press [ENTER]. An F will appear
on the screen.
•To erase the last digit, press [ ] to scroll to
DELETE CHAR then press [ENTER].
•To cancel programming, scroll to CANCEL
and then press [ENTER].
continued on next page
36
One-touch setup and operation
One-touch storage
continued from previous page
6. Press the desired one-touch key to store the
telephone number in the normal location.
-OR Press [LOWER], then the desired one-touch
key to store the telephone number in the lower
location.
NOTES:
• If the desired one-touch key location was empty,
the screen will display SAVED! If there is a already
telephone number in it, the screen will display
REPLACE SPD? You can replace the current
entry by pressing [ENTER] or keep the current
entry by pressing [ ] or [ ] until you see NO
REPLACE? Press [ENTER]. Then choose another
one-touch key location.
• Only the last number dialed from this extension
can be copied to a one-touch location. The other
numbers in the redial stack cannot be copied.
• Press and hold [ENTER] to exit one-touch setup.
37
One-touch setup and operation
To dial a one-touch number
This phone comes with one-touch preference
preset to INTERCOM.
NOTE: To change one-touch preference, see
PREFERENCE on page 35 of this manual.
If one-touch preference is set to INTERCOM:
1.Lift the handset.
-OR Press [ SPEAKER].
-OR Press [HEADSET] and listen for the dial tone.
2. Press the one-touch button.
-OR Press [LOWER], then press the one-touch button
for the destination number you want to call. The
screen displays the number as it is dialed.
If one-touch preference is set to TELEPHONE:
You do not need to go off hook and listen for a
dial tone before dialing a one-touch number. You
can simply:
Press the �����������������
one-touch��������
button.
-ORPress [LOWER], then press the �����������������
one-touch��������
button
for the desired number to call.
The screen displays the number as it is dialed using
the speakerphone or headset as programmed for
automatic mode. (See Automatic mode on page
39 of the installation guide.)
38
One-touch setup and operation
To view or delete a one-touch number
To view a one-touch number
VIEW
5550100
SPD#15
CANCEL
Normal location: SPD# 1-16
Lower Location: SPD# 17-32
1. Press [ENTER].
2. Press [ ] or [ ] until you see ONE TOUCH. Press
[ENTER].
3. Press [ ] or [ ] until you see VIEW. Press
[ENTER].
4. Press the desired one-touch key to view the
telephone number stored in the normal location.
-OR Press [LOWER], then the desired one-touch
key to view the telephone number stored in the
lower location.
-OR Press [ ] or [ ] to view the entries.
5. Press and hold [ENTER] to exit.
To delete a one-touch number
When a one-touch telephone number is displayed,
press [ ] or [ ] to highlight REMOVE and then
press [ENTER] to delete the number. Once
deleted, an entry cannot be retrieved.
39
One-touch setup and operation
To modify a one-touch number
VIEW
5550100
MODIFY
SPD#01
1. When a one-touch telephone number is
displayed, press [ ] or [ ] to highlight MODIFY.
2. Press [ENTER].
3. Press the dialpad keys to enter up to 24 digits.
• You can include a pause while modifying a
dialing sequence which requires one during
actual dialing. Press [ ] or [ ] until you see
PAUSE, then press [ENTER] when storing a
pause. The screen will display P. Each pause
counts as one digit. Continue storing the
number as usual.
• Store a signal for switching to temporary
tone dialing, required for some special services,
if you have dial pulse (rotary) service. Press [ ]
or [ ] until you see TONE, then press [ENTER].
A T will appear on the screen. All numbers
entered after this will send touch tone signals
during dialing.
• You can store the flash signal required by
some special services as part of a dialing
sequence. Press [ ] or [ ] until you see FLASH,
then press [ENTER]. An F will appear on the
screen. Continue storing the number as usual.
• To erase the last digit, scroll to DELETE CHAR
and then press [ENTER].
-OR Press [REMOVE].
• To copy the most recently dialed number
from redial, press [(AUTO) REDIAL]. Only the
last number dialed from this extension can
be copied to a one touch location. The other
numbers in the redial shack cannot be copied.
• To cancel programming, scroll to CANCEL and
then press [ENTER].
continued
����������������������
on next page
40
One-touch setup and operation
To modify a one-touch number
continued from previous page
4. Press the desired one-touch key to store the
telephone number in a location.
-OR Press [LOWER], then the desired one-touch
key to store the telephone number in the lower
location.
5. Press [ ] or [ ] to select CANCEL. Press [ENTER]
to exit the VIEW feature. To move to the next
feature, press [ ].
-OR Press and hold [ENTER] to exit.
NOTE: If the desired one-touch key location
was empty, the screen will display SAVED! If there
is a telephone number in it, the screen will display
REPLACE SPD? You can replace the current entry
by pressing [ENTER], or keep the current entry by
pressing [ ] or [ ] until you see NO REPLACE?
Press [ENTER], then choose another one-touch
key location.
41
Using a 1080 mailbox
Forwarding to DTAD mailbox
About forwarding to DTAD
Answering system on
an auto-attendant
1080 telephone
If at least one 1080 telephone is designated to be
used as an auto-attendant (if you have the 1080 user's manual, read it for more details), you can designate the auto-attendant telephone as a DTAD (Digital
Telephone Answering Device) mailbox for the 1070 or
1040 telephones in the same system.
When the DTAD mailbox is designated, the answering system of the DTAD mailbox 1080 telephone can
answer calls transferred by the auto-attendant system and record caller’s messages for its DTAD system
extensions. These messages are called system extension messages. For more details, refer to the 1080
user's manual.
If the DTAD mailbox is designated, a DTAD system
extensions will display its messages counter
DTAD:XX/YY on its screen. The person on a DTAD
system extension 1040 telephone can access the
DTAD mailbox 1080 telephone to play back messages and record memos (see Listening to messages
- internal access on page 44).
42
Using a 1080 mailbox
To set up call forwarding
To turn call forwarding on
NO ANS CALL FWD
FWD TO DTAD
CALL FROWARD
Use this feature to turn the call forwarding to DTAD
mailbox function on or off.
1. Press [ENTER].
2. Press [ ] or [ ] to scroll to NO ANS CALL FWD.
Press [ENTER].
3. Press [ ] or [ ] to display CALL FORWARD.
4. Press [ ] or [ ] to choose FWD TO DTAD or OFF.
5. Press and hold [ENTER] to save the selection and
exit.
To set call forwarding delay time
NO ANS CALL FWD
15 SEC
FWD DELAY TIME
Use this feature to choose the delay time before an
auto-attendant transferred call is forwarded to the
DATD mailbox 1080 telephone.
1. Press [ENTER].
2. Press [ ] or [ ] to scroll to NO ANS CALL FWD.
Press [ENTER].
3. Press [ ] or [ ] to display FWD DELAY TIME.
4. Press [ ] or [ ] to choose the desired time (2-40
seconds).
5. Press and hold [ENTER] to save the selection and
exit.
43
Using a 1080 mailbox
Listening to messages - internal
access
If a 1040 phone is assigned to a 1080 system
extension mailbox, the screen will display the
number of new and all messages you have. You
will see DTAD: XX/YY, with xx being the number
of new, (unplayed,) messges, and yy the number
of all messages. Follow the steps below to access
the 1080 system extension mailbox to play back
your messages.
NOTE: If there is
no command entered
for 10 seconds,
“Remote operation”
will be announced. If
there is no command
entered for another
10 seconds, the internal access call will
end automatically.
1.Press [INTERCOM], then [0] on a 1040 system
extension.
-OR If you want to alert the person at the 1080
mailbox extension before starting internal access on a 1040 extension, you can make a
single page to the 1080 mailbox (page 42).
2.Enter the three-digit remote access code (111
unless you have changed it, see the installation
guide.
3.Enter commands (See the list below).
4.Press [INTERCOM] on the 1040 system extension to end the internal access and save all
undeleted messages.
Play all messages
[1] [*]
Press to play all extension messages for this 1040
extension.
Play new messages
[1]
Replay current
message and replay
previous message
[2]
Press to play new extension messages for this
1040 extension.
Skip to next message
[3]
Press during playback to skip the current message
and advance to the next message.
Delete message(s)
[#] [#]
Press during playback to delete the current message.
Delete all message(s)
[#] [ ]
Press to delete all messages for this 1040 extension.
Stop
[8]
Press to stop any operation (e.g. stop playback,
stop recording).
Record a memo
[9] to begin recording
[8] to stop recording
Press [9], wait for beep then begin speaking. Press
[8] to stop recording.
*
Press within 3 seconds of the message playing to
go back to the previous message. Press after 3
seconds of the message playing to repeat the
message currently playing.
44
Appendix A
Glossary
Auto Attendant: If there is at least one 1080 telephone in your system, it
may be set up to be an auto attendant. The auto attendant is assigned to pick
up a ringing line automatically after a selected number of rings. It may also
be set up to record messages for your extension. The auto attendant plays
the selected auto attendant message and redirects the call if the caller enters
an extension number.
Central message: If a 1080 telephone is assigned as an auto attendant, when
a call is answered by the auto attendant, and a caller presses [9], a central
message, one not intended for any particular extension, is created.
Centrex service: This is a special subscriber service which may be available from
your local telephone company for a fee. This 1040 telephone can be used with
Centrex service.
DND: When activated, the Do Not Disturb (DND) feature prevents
interruptions during a call.
DSL: Digital subscriber line, (DSL) service is available from your telephone
company for a fee. It allows you to receive high-speed internet through
your telephone line(s). Some special equipment, splitters and/or filters, are
required for the telephone and data service to work properly together.
DTAD: The Digital Telephone Answering Device is a sophisticated, tapeless
answering system built into the 1080 telephone. In some installations,
messages for your phone can be recorded on a 1080 in your system.
Line group: A group of system telephones sharing some lines within a multitelephone system.
Mailbox: A place to store answering system messages. A 1080 phone can
store system extension messages for your extension.
Navigation keys: These are the buttons used when programming your 1040
phone and for scrolling through feature options ([ENTER], [ ], [ ], [ ], [ ]).
Prime line: This is the line on the telephone you assign to be selected
automatically when you lift the handset, press [ SPEAKER] or press
[HEADSET] to answer or make a call.
System extension message: The messages recorded for individual 1070 and
1040 telephones that are associated with a 1080 phone’s auto attendant mailbox
(pages 30).
System telephone: Any 1080, 1070 or 1040 telephone in your telephone
system (also called an extension).
Telephone system (or business system): Two or more system telephones
combined to form an interacting system of shared lines. You can have up to
16 system telephones in the system.
45
Appendix B
Time/date
When the telephone is idle, the screen will display
the date and time. To set the time follow the
steps below.
1.Press [ENTER].
2.Press [ ] or [ ] until you see TIME/DATE.
TIME/DATE
= 2007
YEAR
3.Press [ENTER] to see YEAR. Press the dialpad
keys to enter the correct year.
4.Press [ ] until you see MONTH. Press the
dialpad keys to enter the correct month.
5.Press [ ] until you see DATE. Press the dialpad
keys to enter the correct date.
6.Press [ ] until you see HOUR. Press the dialpad keys to enter the correct hour (12-hour
clock format).
7.Press [ ] until you see MINUTE. Press the
dialpad keys to enter the correct minute.
8.Press [ ] until you see AM/PM. Press [ ] or[ ]
to highlight AM or PM.
9.To move to MAIN MENU, press [ ].
-OR To exit setup, press and hold [ENTER].
46
Appendix C
Centrex operation
Set ring delay duration
This feature allows other system telephones’ calls
to ring at the console phone. After a specified
ring delay, the calls will ring at the console
phone. (See CSL DELAY RING on page 75 of the
installation guide.)
Answer a delayed ring
The console phone rings and the screen displays
the extension number of the intercom sending the
delayed ring.
1.Select an idle line.
2.Enter the Centrex pickup code.
3.Enter the seven- or ten-digit phone number (as
directed by your phone company) of the extension sending the delayed ring.
NOTE: If the console is using another line and
receives a delayed ring, the console phone can
put the other line on hold and follow steps 1–3.
If the console is on an intercom call, the intercom
call should be ended before picking up the ringing
phone.
Pick up another station’s line
1.Choose an idle Centrex line.
2.Enter the Centrex pickup code.
3.Enter the seven- or ten-digit phone number (as
directed by your phone company) of the desired
line you want.
47
Appendix C
Centrex operation
If you subscribe to
Centrex service provided
by your local telephone
company, you need
to set up the system
telephones first: Here
is an example of one
setup.
EXT 11 (console)
CONSOLE is ON.
CSL DELAY RING is
OFF.
EXT 12
CONSOLE is OFF.
CSL DELAY RING is set
to 20 seconds.
EXT 13
CONSOLE is OFF.
CSL DELAY RING is set
to 16 seconds.
EXT 14
Both CONSOLE and
CSL DELAY RING
menus are OFF. (This
telephone does not use
the Centrex service.)
Centrex service call example
In the example on the left, when the calls coming
from 555-1237 or 555-1238 are not answered, if
you subscribe to the Centrex service provided by
your local telephone company, these calls will be
switched to the console telephone (EXT 11 in the
example).
1. An external call comes in on line 4 (telephone
number 555-1237 or 555-1238) on the original
system telephone (EXT 12 or EXT 13).
2. If the call is not answered during the CSL delay
time set on the original extension, (20 seconds
for EXT 12 or 16 seconds for EXT 13), the
console telephone (EXT 11) will ring and display
EXT XX RING.
3. Press the [LINE 4] key if line 4 is idle on the
console telephone (EXT 11). Dial the Centrex
access code (provided by your telephone
company) then the ringing line’s seven- or tendigit phone number, (as directed by your phone
company).
NOTES:
• If no one answers the call at the console
telephone for 10 seconds, the originating
extension will ring again.
• Outside calls will be answered by the auto
attendant (see the 1080 user’s manual for
details).
• Contact your telephone company for more details
about Centrex service.
48
Appendix D
General product care
To keep your phone working well and looking
good, follow these guidelines:
• Avoid putting it near heating appliances and
devices that generate electrical noise (for
example, motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the phone and/or other rough
treatment.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive
powder because this can damage the finish.
• Retain the original packaging in case you need
to ship it at a later date.
49
Appendix E
Important product information
This symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric
shock.
Safety information
• Read and understand all instructions in the user’s manual. Observe all
markings on the product.
• Avoid using a telephone during a thunderstorm. There may be a slight
chance of electric shock from lightning.
• Do not use a telephone in the vicinity of a gas leak. If you suspect a gas leak,
report it immediately, but use a telephone away from the area where gas is leaking.
If this product is a cordless model, make sure the base is also away from the area.
•
Do not use this product near water, or when you are wet. For example, do
not use it in a wet basement or shower, or next to a swimming pool, bathtub,
kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning.
If the product comes in contact with any liquids, unplug any line or power
cord immediately. Do not plug the product back in until it has dried thoroughly.
• Install this product in a protected location where no one can trip over any
line or power cords. Protect cords from damage or abrasion.
•
If this product does not operate normally, read Troubleshooting in this user’s
manual. If you cannot solve the problem, or if the product is damaged, refer to
the limited warranty. Do not open this product except as may be directed in
your user’s manual. Opening the product or reassembling it incorrectly may
expose you to hazardous voltages or other risks.
• If this product has user-replaceable batteries, replace batteries only as
described in your user’s manual. Do not burn or puncture batteries—they
contain caustic chemicals.
•
If this product has a three-prong (grounding) plug or a polarized plug
with one wide prong, it may not fit in non-polarized outlets. Do not defeat
the purpose of these plugs. If they do not fit in your outlet, the outlet should
be replaced by an electrician.
CAUTION: Use only the power adapter provided with this product. To
obtain a replacement, visit our website at www.telephones.att.com,
or call 1 (800) 222–3111. In Canada, dial 1 (866) 288-4268.
50
Appendix E
Important product information
Especially about corded telephones
•
Electrical power: The telephone base must be connected to a working
electrical outlet. The electrical outlet should not be controlled by a wall switch.
Calls cannot be made from the handset if the telephone base is unplugged
or switched off, or if the electrical power is interrupted.
• Power adapter: The power adapter is intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed to hold the
plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
Especially about telephone answering systems
Two-way recording: This unit does not sound warning beeps to let the other
party know that the call is being recorded. To ensure that you are in compliance with any federal or state regulations regarding recording a telephone call,
you should start the recording process and then inform the other party that you
are recording the call.
SAVE THESE INSTRUCTIONS
51
Appendix F
FCC and ACTA information
If this equipment was approved for connection to the telephone network prior
to July 23, 2001, it complies with Part 68 of the Federal Communications
Commission (FCC) rules. If the equipment was approved after that date, it
complies with the Part 68 rules and with the Technical Requirements for Connection of Equipment to the Telephone Network adopted by the Administrative Council for Terminal Attachments (ACTA). We are required to provide you
with the following information.
1. Product identifier and REN information
The label on the back or bottom of this equipment contains, among other
things, an identifier indicating product approval and the Ringer Equivalence
Number (REN). This information must be provided to your local telephone company upon request. For equipment approved prior to July 23, 2001, the product
identifier is preceded by the phrase “FCC Reg No.” and the REN is listed separately. For equipment approved after that date, the product identifier is preceded by “US” and a colon (:), and the REN is encoded in the product identifier
without a decimal point as the sixth and seventh characters following the colon.
For example, the product identifier US:AAAEQ03T123XYZ would indicate an REN
of 0.3.
The REN is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. In most, but not all
areas, the sum of all RENS should be five (5.0) or less. You may want to contact
your local telephone company for more information.
2. Connection and use with the nationwide telephone network
The plug and jack used to connect this equipment to the premises wiring and
the telephone network must comply with the applicable part 68 rules and
technical requirements adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. An RJ11 jack should normally
be used for connecting to a single line and an RJ14 jack for two lines, see
installation instructions in the user’s manual. This equipment may not be used
with coin telephone lines or with party lines. If you have specially wired alarm
dialing equipment connected to your telephone line, ensure the connection of
this equipment does not disable your alarm equipment. If you have questions
about what will disable the alarm equipment, consult your telephone company
or qualified installer.
3. Repair instructions
If this equipment is malfunctioning, it must be unplugged from the modular jack
until the problem has been corrected. Repairs to this telephone equipment can
only be made by the manufacturer or its authorized agents. For repair procedures,
follow the instructions outlined under the limited warranty.
52
Appendix F
FCC and ACTA information
4. Rights of the telephone company
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you
of your right to file a complaint with the FCC. Your telephone company may make
changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone company is required to notify
you if such changes are planned.
5. Hearing aid compatibility
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
6. Programming/testing of emergency numbers
If this product has memory dialing locations, you may choose to store police, fire
department and emergency medical service telephone numbers in these locations. If you do, please keep three things in mind:
a. We recommend that you also write the telephone number on the directory
card (if applicable), so that you can still dial the emergency number manually if
the memory dialing feature doesn’t work.
b. This feature is provided only as a convenience, and the manufacturer assumes
no responsibility for customer reliance upon the memory feature.
c. Testing the emergency telephone numbers you have stored is not recommended.
However, if you do make a call to an emergency number:
• You must remain on the line and briefly explain the reason for the call before
hanging up.
• Programming/testing of emergency numbers should be performed during
off-peak hours, such as in the early morning or late evening, when the
emergency services tend to be less busy.
53
Appendix G
Part 15 of FCC rules
Some telephone equipment generates, uses, and can radiate radio-frequency
energy and, if not installed and used properly, may cause interference to radio
and television reception. This product has been tested and found to meet the
standards for a class B digital device, as specified in part 15 of the FCC rules.
These specifications area designed to provide reasonable protection against
such interference in a residential installation. However, there is no guarantee
that interference will not occur in a particular installation.
If this product causes interference to radio, VCR or television reception when
it is in use, you might correct the interference with any one or all of these
measures:
• Where it can be done safely, re-orient the receiving radio, VCR or television
antenna.
• To the extent possible, relocate the radio, VCR, television or other receiver
with respect to the telephone equipment.
• If this telephone product runs on AC power, plug your product into an AC
outlet that’s not on the same circuit as one used by your radio, VCR or television.
Modifications to this product, not expressly approved by the manufacturer,
could void the user’s authority to operate the equipment.
54
Appendix H
Limited warranty
The AT&T brand is used under license - any repair, replacement or warranty service,
and all questions about this product should be directed to: In the United States of
America call 1 (800) 222-3111 or visit www.telephones.att.com;
In Canada, call 1 (866) 288-4268.
1. What does this limited warranty cover?
The manufacturer of this AT&T-branded product warrants to the holder of
a valid proof of purchase (“CONSUMER” or “you”) that the product and all
accessories provided in the sales package (“PRODUCT”) are free from defects
in material and workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with the PRODUCT
operating instructions. This limited warranty extends only to the CONSUMER
for products purchased and used in the United States of America and Canada.
2. What will be done if the PRODUCT is not free from defects in materials
and workmanship during the limited warranty period (“materially defective PRODUCT”)?
During the limited warranty period, the manufacturer’s authorized service
representative will repair or replace at the manufacturer’s option, without
charge, a materially defective PRODUCT. If the manufacturer repairs the
PRODUCT, they may use new or refurbished replacement parts. If the
manufacturer chooses to replace the PRODUCT, they may replace it with a
new or refurbished PRODUCT of the same or similar design. The manufacturer
will retain the defective parts, modules, or equipment. Repair or replace ment of the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The manufacturer will return the repaired or replacement products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
3. How long is the limited warranty period?
The limited warranty period for the PRODUCT extends for ONE (1) YEAR
from the date of purchase. If the manufacturer repairs or replaces a materially
defective PRODUCT under the terms of this limited warranty, this limited
warranty also applies to repaired or replacement PRODUCT for a period of
either (a) 90 days from the date the repaired or replacement PRODUCT is
shipped to you or (b) the time remaining on the original one-year limited
warranty; whichever is longer.
55
Appendix H
Limited warranty
4. What is not covered by this limited warranty?
This limited warranty does not cover:
• PRODUCT that has been subjected to misuse, accident, shipping or other
physical damage, improper installation, abnormal operation or handling,
neglect, inundation, fire, water, or other liquid intrusion; or
• PRODUCT that has been damaged due to repair, alteration, or modification
by anyone other than an authorized service representative of the
manufacturer; or
• PRODUCT to the extent that the problem experienced is caused by signal
conditions, network reliability or cable or antenna systems; or
• PRODUCT to the extent that the problem is caused by use with non-AT&T
accessories; or
• PRODUCT whose warranty/quality stickers, PRODUCT serial number plates
or electronic serial numbers have been removed, altered or rendered
illegible; or
• PRODUCT purchased, used, serviced, or shipped for repair from outside
the United States of America or Canada, or used for commercial or
institutional purposes (including but not limited to products used for rental
purposes); or
• PRODUCT returned without valid proof of purchase (see item 6 below); or
• Charges for installation or setup, adjustment of customer controls, and
installation or repair of systems outside the unit.
5. How do you get warranty service?
To obtain warranty service in the United States of America, call 1 (800) 222-3111; in Canada, please dial 1 (866) 288-4268.
NOTE: Before calling for service, please review the user’s manual. A check of
the PRODUCT controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and are responsible for delivery or handling
charges incurred in the transport of the PRODUCT(s) to the service location.
The manufacturer will return repaired or replaced PRODUCT under this limited
warranty to you, transportation, delivery or handling charges prepaid. The
manufacturer assumes no risk for damage or loss of the PRODUCT in transit.
If the PRODUCT failure is not covered by this limited warranty, or proof of
purchase does not meet the terms of this limited warranty, the manufacturer
will notify you and will request that you authorize the cost of repair prior to
any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty.
56
Appendix H
Limited warranty
6. What must you return with the PRODUCT to get warranty service?
You must:
a. Return the entire original package and contents including the PRODUCT
to the service location along with a description of the malfunction or difficulty;
and
b. Include “valid proof of purchase” (sales receipt) identifying the PRODUCT
purchased (PRODUCT model) and the date of purchase or receipt; and
c. Provide your name, complete and correct mailing address, and telephone
number.
7.
Other limitations
This warranty is the complete and exclusive agreement between you and
the manufacturer of this AT&T branded PRODUCT. It supersedes all other
written or oral communications related to this PRODUCT. The manufacturer
provides no other warranties for this PRODUCT. The warranty exclusively
describes all of the manufacturer’s responsibilities regarding the PRODUCT.
There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state or province
to province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the PRODUCT is
fit for ordinary use) are limited to one year from date of purchase. Some
states/provinces do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. In no event shall the
manufacturer be liable for any indirect, special, incidental, consequential, or
similar damages (including, but not limited to lost profits or revenue, inability to
use the PRODUCT or other associated equipment, the cost of substitute
equipment, and claims by third parties) resulting from the use of this PRODUCT.
Some states/provinces do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not
apply to you.
Please retain your original sales receipt as proof of purchase.
57
Appendix I
Technical specification
Operating temperature
32°F — 122°F
0°C — 50°C
Power adapter input
AC120V 60Hz
Power adapter
output
DC12V 500mA
Backup battery
(purchased separately)
Alkaline 9V, size 1604A
Headset jack
2.5mm, 32 - 150ohm
Wiring limitation
No more than 600 feet
REN
0.3B
System signal carrier
frequency
1.7 MHz
58
Appendix J
In case of difficulty
If you have difficulty with your telephone, please try the suggestions below.
For Customer Service, visit our website at www.telephones.att.com, or
call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Have the
serial number, found on the underside of your phone, available when contacting
customer service. Please retain your receipt as your proof of purchase.
To purchase accessories or replacement parts, please contact customer
service by visiting our website at www.telephones.att.com or calling
1 (800) 222–3111. In Canada, dial 1 (866) 288-4268.
My telephone appears to
be dead.
• Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
•Make sure the telephone line cords are plugged firmly into the telephone base and the jack.
•Unplug the telephone’s electrical power. Wait for approximately 15 seconds, then plug it back in.
Allow up to one minute for the telephone to synchronize.
•This system is not compatible with any other AT&T 4-line small business telephones, except for the 1040, 1070 and 1080 telephones.
System features,
•This system is not compatible with any other (intercom, transfer, hold
AT&T 4-line small business telephones, except release, etc.) do not work for the 1040, 1070 and 1080 telephones.
with my old AT&T 4-line
telephones (984, 974, 945,
etc.).
Intercom, hold, call
privacy or other
advanced features do
not work properly.
• If you have fiber optic service, (digital service to
the building, analog service within the building,)
VoIP (Voice over the Internet) service, or cable
telephone service, the router that the system
uses may interfere with system communication.
• If Line 1 is a DSL line, have a professional install
a splitter on the telephone line. See the installation guide and contact your DSL service
provider for more information.
59
Appendix J
In case of difficulty
• If the wiring for your system is greater than 600
feet, some of the advanced features may not
work properly. You may have to remove some
of the phones from remote areas.
•Check to make sure that each telephone set
has a unique extension number. If the sets
receive AC power at the same time, either at
initial installation or after a power failure, the
extension numbers may be the same. Refer to
the EXTENSION NUMBER section on page 32 of
the installation guide.
There is no dial tone.
•First, try all the suggestions of My telephone
appears to be dead on page 59.
•The telephone line cord might be malfunctioning.
Try installing a new telephone line cord.
•Disconnect the telephone base from the telephone
jack and connect a different telephone. If there
is no dial tone on the telephone either, the
problem is in your wiring or local service. Contact
your local telephone company.
•Make sure a line is selected. Press a line button or speakphone.
•Make sure the [HOLD] key is not pressed.
• If there is no dial tone when the [HEADSET] key
is pressed, make sure the headset is firmly connected in the HEADSET jack.
I cannot dial out.
•First, try all the above suggestions in There is no dial tone on this page.
•Make sure there is a dial tone before dialing. It is normal if the telephone takes a second or two to synchronize before producing a dial tone. Wait an extra second before dialing.
•Check that all the telephones connected to the
same telephone line are hung up.
•Make sure the telephone is set to the correct
dial mode (pulse dial or tone dial) for the service
in your area. Refer to the TONE/PULSE section, on page 36 of the installation guide, to set the dial mode.
60
Appendix J
In case of difficulty
•If the other telephones in your home are having
the same problem, the problem is in the wiring or
local service. Contact your local telephone company
(charges may apply).
•If you are using the speakerphone, eliminate any background noise. Noise from a television, radio, or other appliances may cause the telephone to not dial out properly. If you cannot eliminate the background noise, first try muting the telephone before dialing, or dialing from another room in your home with less background noise.
I cannot page or make
intercom calls.
•Make sure you dialed the extension correctly.
•Make sure Line 1 is connected and has the same phone number on all system phones.
•The destination telephone may be on an external call. Wait and try again.
•Make sure the Do Not Disturb function is turned off on the destination system telephone (page 15).
•Make sure the [INTERCOM] light is off before you making a page or Intercom call. If the light is on, the system is busy or the intercom is unavailable. Try again when the intercom light goes out.
•Make sure the telephone line cord connected to line jack L1/L2 was provided with the telephone.
• Check to make sure that each telephone set has a unique extension number. If the sets receive AC power at the same time, either at initial installation or after a power failure, the extension numbers may be the same. Refer to the EXTENSION NUMBER section on page 32 of the installation guide.
61
Appendix J
In case of difficulty
I cannot transfer outside
calls.
•If you are on a conference call with another telephone in the same system (page 22), the call
cannot be transferred.
•If the destination telephone is on an outside call
or intercom call with another system telephone,
the call cannot be transferred.
•All extensions must have the same outside telephone line connected to Line 1.
•Make sure the telephone line cord connected to line jack L1/L2 was provided with the tele- phone.
• Check to make sure that each telephone set has a unique extension number. If the sets receive AC power at the same time, either at initial installation or after a power failure, the extension numbers may be the same. Refer to the EXTENSION NUMBER section on page 32 of the installation guide.
LOW BATT is displayed on •No spare battery is installed or the spare battery needs to be replaced.
screen.
•Remove and re-install the battery.
The telephone does not
ring when there is an
incoming call.
•Make sure the ringer is on (page 14).
•Make sure the telephone line cord(s) and the power adapter are plugged in properly (see the installation guide).
•There may be too many extension telephones on
the telephone line to allow all of them to ring
simultaneously. Try unplugging one phone at a time until the phones start ringing.
•Test a working telephone at the same telephone
jack. If another telephone has the same problem, the problem is in the telephone jack. Contact your local telephone company (charges may apply).
62
Appendix J
In case of difficulty
•The telephone line cord might be malfunctioning.
Try installing a new telephone line cord.
•Make sure the Do Not Disturb feature is not activated
(page 15).
•If you are on a call, there will be a beep to alert you of incoming calls on the other lines.
Cannot join a
conversation in progress.
•The call privacy feature prevents another set on the system from interrupting a conversation. • Make sure you press the LINE button to release privacy. (See Call privacy on page 21.)
Display screen is blank.
•Make sure the power cord is connected to both the phone and an electrical outlet not controlled by a wall switch.
The call privacy feature
does not work.
•In some installations that have fiber optic service (digital service to the building, analog service within the building) the signals to the extensions may not support the call privacy feature.
Error tone (fast busy signal) when making a page
call.
•The Do Not Disturb feature is activated at the extension you are calling.
A double beep sounds
every 30 seconds.
•There is a call on hold at this extension. Press and release the LINE button of the call on hold
to return to the call and turn off the reminder beep.
Operation during a power •This phone will operate during a power failure failure.
if a working battery has been installed. You will be able to answer calls with the handset and dial calls using the dial pad keys and the
one-touch or redial features. No other features will work until power is restored. All programming is retained during a power failure.
63
Appendix J
In case of difficulty
The screen displays AC
FAIL.
•The phone has been disconnected from AC power. When AC power is restored, the screen will return to the usual display. One touch and redial numbers are retained until power is restored.
My calls fade out or cut in •If you have a headset plugged into the telephone,
and out when I am using try unplugging it and firmly plugging it in again.
the telephone.
• Disconnect the telephone base from the
modular jack and plug in another corded
telephone. If calls are still not clear, the problem
is probably in the wiring or local service. Contact
your local service company (charges may apply).
•If you are using the speakerphone when this problem occurs, eliminate any background noise. Noise from the television, radio, or other appliances
may cause the speakerphone to cut in and out.
Try engaging the [MUTE] button when you are not
speaking or eliminating the background noise.
•If you have Digital Subscriber Line, (DSL,) service,
and you have more than three telephone sets,
and you have installed microfilters, you may
need to have a DSL splitter installed by your DSL
service provider.
The sound quality of the
headset is poor
•Unplug it and and firmly plug it in again.
I hear other calls when
using the telephone.
•Disconnect the telephone base from the telephone
jack. Plug in a different telephone. If you still hear other calls, the problem is probably in the wiring or local service. Call your local telephone company.
•Make sure you are using the round black cords that came with the phone. These cords help prevent crosstalk (hearing other calls.)
64
Appendix J
In case of difficulty
Common cure for
electronic equipment:
If the telephone is not responding normally, try
the following (in the order listed):
1.Disconnect the power to the telephone base.
2.Disconnect the spare battery (if the set has one).
3.Wait a few minutes before connecting power to
the telephone base.
4.Re-install the spare battery (if the set has one).
5.Wait for the telephone to synchronize its
connection. This may take up to one minute.
The answering system
does not respond to
internal access
commands.
•
•
•
•
Make sure your remote access code is correct
(see the installation guide for more details).
If you access the extension mailbox through a single page call, make sure the extension number of the extension mailbox telephone is entered correctly.
The extension mailbox is in use. Or the two
intercom paths are in use. Wait for a few minutes
then try again.
There may be interference on the telephone line you
are using. Press the dial pad keys firmly when dialing.
65
Index
A
H
AC fail, 4
Alert tones, 7
Answering calls, 9
Auto-mute, 30
Auto-redial, 18
Handset, 10, 12
Hands-free use, 10, 12
Headset, 11, 12
Hold a call, 20
I
C
Important product instructions,
50-51
In case of difficulty, 59-65
Incoming calls answering, 9-12
Indicator light, 6-7
Intercom, 25-33
Internal access, 44
Call privacy, 21
Call forwarding delay time, 43
Call transfer, 23
Conference call, 22
D
Delete redial entries, 17
Dialing
one-touch dialing, 38
Directory card, 8
Do not disturb, 15
DSL, 42, 45
DTAD, 45
L
E
M
Ending calls, 10
Making calls, 9-12
Memo, 44
Menu operation, 3
Message playback, 44
Mute, 19
Last number redial, 16-18
LCD contrast, 4
Listen to message, 44
Line group, 28
Low battery, 5, 62
Lower location, 34
F
FCC and ACTA, 52
Flash, 19
Forward to DTAD, 42
66
Index
N
Single-phone page, 29, 30
Speakerphone, 7, 10
System extension message, 42,
44
System extension mailbox, 42-44
Switch lines, 21
Switch speaking mode, 12
Navigation keys, 3
O
One-touch keys, 3, 34
delete entries, 39
dial number, 38
new entries, 36-37
preference, 35
T
Technical specifications, 58
Temporary tone dialing, 19
P
V
Page all, 31
Pause, 36, 40
Prime line, 9
Private line, 21-22
Volume control, 13
Voice page, 29-33
W
R
Warranty, 55-57
Receiving calls, 9-12
Redial stack, 17
Ringer on or off, 14
Ringer type, 14
Ringer volume, 13
Room monitor, 33
S
Screen display messages, 4-5
67
www.telephones.att.com
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a
AT&T Intellectual Property licensed to Advanced American Telephones.
Printed in China. Issue 3 AT&T 11/07.