AEG Thyro-S H1 Network Card User Manual

Installation/Operation
CC3610 and CC3710 Series
Color Camera
C2914M-F (08/05)
Pelco Worldwide Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com
USA & Canada: Tel 800/289-9100 • FAX 800/289-9150
International: Tel: 1-559/292-1981 • FAX 1-559/348-1120
® Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit and Camclosure are registered trademarks of Pelco.
™Endura and ExSite are trademarks of Pelco
™DLP is a trademark of Texas Instruments, Inc.
™SuperHAD CCD is a trademark of the Sony Corporation.
© Copyright 2005, Pelco. All rights reserved.
[2]
Pelco Manual C2914M-F (08/05)
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................... 4
REGULATORY NOTICES ................................................................................................................................. 5
DESCRIPTION ................................................................................................................................................... 6
Models ........................................................................................................................................................... 6
CAMERA LAYOUT ............................................................................................................................................. 7
INSTALLATION .................................................................................................................................................. 7
Lens Mounting ............................................................................................................................................... 7
Camera Mounting .......................................................................................................................................... 8
CONNECTIONS ................................................................................................................................................. 9
Video Connections ........................................................................................................................................ 9
Power Connections ....................................................................................................................................... 9
RJ45-10 Connections ................................................................................................................................... 11
Service Connection ..................................................................................................................................... 12
CAMERA SETUP ............................................................................................................................................. 13
Lens Setup and Focus Procedures ............................................................................................................. 13
Back Focus Adjustment ............................................................................................................................... 14
Switch Settings ............................................................................................................................................ 15
Camera Synchronization ............................................................................................................................. 17
SPECIFICATIONS ........................................................................................................................................... 18
WARRANTY AND RETURN INFORMATION ................................................................................................. 22
LIST OF ILLUSTRATIONS
1
2
3
4
5
6
7
8
Camera Layout ............................................................................................................................. 7
AID/AIV Lens Connector .............................................................................................................. 7
Camera Mounting ......................................................................................................................... 8
RJ45-10 Connector ...................................................................................................................... 11
Service Connector ...................................................................................................................... 12
AGC and ESC Switch Settings ................................................................................................... 13
Back Focus Adjustment .............................................................................................................. 14
Switch Settings ........................................................................................................................... 15
LIST OF TABLES
A
B
C
Video Coaxial Cable Requirements ............................................................................................. 9
Wiring Distances for 5 VA Cameras (24 VAC/12 VDC) .............................................................. 10
RJ45-10 Pinouts .......................................................................................................................... 11
Pelco Manual C2914M-F (08/05)
[3]
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from tha apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as when the power supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, the apparatus
does not operate normally, or the apparatus has been dropped.
Apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Installation should be done only by qualified service personnel and conform to all local codes.
Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed
for indoor use only and it must not be installed where exposed to rain and moisture.
Use only installation methods and materials capable of supporting four times the maximum specified load.
CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of
shock, do not perform any servicing other than that contained in the operating instructions unless you are
qualified to do so.
Only use replacement parts recommended by Pelco.
Only power 12 VDC/24 VAC cameras from a UL Listed Class 2 power supply.
For outdoor use, an appropriate protective housing conforming to IP65 or better must be used. For UL, a
UL Listed enclosure suitable for the application must be used.
DD/AI Lens Connector
The maximum load for a direct drive lens must not exceed 25 mA
The maximum load for an auto iris lens must not exceed 50 mA.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
[4]
Pelco Manual C2914M-F (08/05)
REGULATORY NOTICES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
CC3610H-6, CC3610H-6X, CC3710S-6, CC3710S-6X, CC3710H-6, CC3710H-6X and CC3610H-7 models:
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV
Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C.
20402.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CC3710H-7 and CC3710S-7 models:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Modifications not expressly approved by the manufacturer could void the user’s authority to operated the equipment
under FCC rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Pelco Manual C2914M-F (08/05)
[5]
DESCRIPTION
CC3610 and CC3710 Series cameras are color video cameras with a 1/3-inch CCD imager. All cameras have a
direct drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses.
Models
CC3610H-6
CC3610H-6X
CC3610H-7
CC3610H-7X
CC3710S-6
CC3710S-6X
CC3710S-7
CC3710S-7X
CC3710H-6
CC3710H-6X
CC3710H-7
CC3710H-7X
[6]
High resolution (480 TV lines), Exview HAD™ CCD, 0.4 lux at F1.2, NTSC, 12 VDC/24 VAC
High resolution (480 TV lines), Exview HAD™ CCD, 0.4 lux at F1.2, PAL, 12 VDC/24 VAC
High resolution (480 TV lines), Exview HAD™ CCD, 0.4 lux at F1.2, NTSC, 110-240 VAC
High resolution (480 TV lines), Exview HAD™ CCD, 0.4 lux at F1.2, PAL, 110-240 VAC
Standard resolution (330 TV lines), SuperHAD™ CCD, 0.6 lux at F1.2, NTSC, 12 VDC/24 VAC
Standard resolution (330 TV lines), SuperHAD™ CCD, 0.6 lux at F1.2, PAL, 12 VDC/24 VAC
Standard resolution (330 TV lines), SuperHAD™ CCD, 0.6 lux at F1.2, NTSC, 110-240 VAC
Standard resolution (330 TV lines), SuperHAD™ CCD, 0.6 lux at F1.2, PAL, 110-240 VAC
High resolution (480 TV lines), SuperHAD™ CCD, 0.7 lux at F1.2, NTSC, 12 VDC/24 VAC
High resolution (480 TV lines), SuperHAD™ CCD, 0.7 lux at F1.2, PAL, 12 VDC/24 VAC
High resolution (480 TV lines), SuperHAD™ CCD, 0.7 lux at F1.2, NTSC, 110-240 VAC
High resolution (480 TV lines), SuperHAD™ CCD, 0.7 lux at F1.2, PAL, 110-240 VAC
Pelco Manual C2914M-F (08/05)
CAMERA LAYOUT
Figure 1. Camera Layout
INSTALLATION
Lens Mounting
CC3610 and CC3710 Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses. Cameras
are factory-set for CS-mount lenses, but are easily adjusted for C-mount lenses.
1.
C-Mount Lens Only - Loosen the two back focus locking screws. Rotate the back focus adjustment ring fully counterclockwise before installing the C-mount lens (refer to the section on Back Focus
Adjustment).
2.
Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the
lens and the CCD element. If necessary, use clean, compressed air to remove any foreign matter.
3.
Auto Iris Lens Only - Connect the auto iris lens to the four-pin iris drive connector located on
the side of the camera. Pin connections for the iris drive connector are as follows.
Camera Connector
PIN
1
2
3
4
DC (AID) AUTO IRIS LENS
Control coil positive (+)
Control coil negative (-)
Drive coil negative (-)
Drive coil positive (+)
VIDEO (AIV) AUTO IRIS LENS
Not used
Lens positive supply
Ground
Video drive signal
Figure 2. AID/AIV Lens Connector
Maximum load:
50 mA video auto iris lens
25 mA direct drive lens
Pelco Manual C2914M-F (08/05)
[7]
Camera Mounting
Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a
bracket or tripod. They are designed to accept standard photographic mounting bolts (1/4-inch UNC-20). The
mounting bracket must be capable of supporting the weight of the camera and its lens.
NOTE: Some installation codes dictate that the mounting bracket must be capable of supporting up to four
times the combined weight of the camera and lens.
Figure 3. Camera Mounting
[8]
Pelco Manual C2914M-F (08/05)
CONNECTIONS
CC3610 and CC3710 Series cameras offer standard power and coax video connectors as well as an RJ45-10
connector that combines low voltage power and video (composite or UTP). These cameras also have a service
connector allowing a video monitor to be connected locally to the camera using a composite video BNC cable.
Video Connections
To obtain a video output, connect a video coaxial cable terminated with a 75 Ω BNC connector to the BNC
socket marked VIDEO OUT on the rear of the camera. Refer to Table A for the type of video coaxial cable to use.
Table A. Video Coaxial Cable Requirements
Cable Type*
RG59/U
RG6/U
RG11/U
Maximum Distance
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
* Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
Another way to transmit video is over unshielded twisted pair wiring through the RJ45-10 connector. Refer to
the RJ45-10 Connections section. When outputting composite video through the BNC or RJ45-10, do not send
UTP output to a passive UTP receiver. However it is acceptable to use an active UTP receiver for UTP output
in combination with the other video connections.
Power Connections
CC3610 and CC3710 Series cameras are available in AC high voltage and AC/DC low voltage types. The
voltage required to operate the camera is clearly marked on the rear panel of the camera. The green POWER
LED on the rear panel indicates that power is connected. Power low voltage cameras only from a UL Listed
Class 2 isolated power supply. Power consumption is 5 watts.
Mains Power Supply
Cameras that are intended to operate directly from the mains supply are fitted with a nondetachable power
supply cord. The voltage of operation is 110 to 240 VAC at 50/60Hz.
WARNING: Refer to the wiring instruction label attached to the supply cord. For instances
where the camera will be connected to a socket outlet, the camera should be connected to an
easily accessible socket outlet near to the camera. For instances where the camera will be
connected to the building installation, the building wiring should incorporate a readily accessible
disconnect device, with a contact separation greater than three millimeters. This device should be
fitted into the live conductor, if that is readily identifiable, or should be 2-pole. All installations shall
be carried out in accordance with the locally applicable installation rules.
WARNING: Fuse (F1) should only be replaced by one of equivalent type and rating
1A (T) HRC 250V
WARNING: This camera is a Class 2 device and therefore does not have an earth connection
in the power cord. The leakage current on these cameras is well within safe limits. However, it is
advisable to connect the coaxial or RJ45-10 cable from the camera to the receiving equipment
(such as a monitor or matrix) before applying power to the camera, so that this small leakage
current has a low resistance path to earth.
Pelco Manual C2914M-F (08/05)
[9]
Low Voltage Power Supply
Cameras fitted with an automatic-switching low voltage power supply operate at 10.8 to 13.8 VDC (12 VDC
-10% +15%) or 20.4 to 27.6 VAC (24 VAC ±15%) at 50/60Hz. Connections and polarity are indicated adjacent to
the screw terminals on the rear panel.
Refer to Table B for the recommended wire gauge and wiring distances.
WARNING: When powering the camera via the screw terminals, ensure that the power
connections to the RJ45-10 connector are not used, and that any connections to the RJ45-10 are
not shorted together. The power supply must be a UL Listed Class 2 isolated type.
CAUTION: AC Operation Only - When wiring more than one camera to the same transformer,
connect the same side of the transformer to the same terminal on all cameras. Failure to connect
all of the cameras the same way will cause the cameras to be out of phase with each other and
may produce a vertical roll when switching between cameras.
Table B. Wiring Distances for 5 VA Cameras (24 VAC/12 VDC)
The following are the recommended maximum distances for low voltage cameras. These distances are calculated
with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered
devices.)
Wire Gauge
24 VAC
12 VDC
AWG
mm2
Feet
Meters
Feet
Meters
24
22
20
18
16
14
12
10
0.25
0.35
0.5
1
1.5
2.5
4
6
224
356
567
902
1432
2285
3622
5760
68
108
172
274
436
696
1103
1755
56
89
141
225
358
571
905
1440
17
27
42
68
109
174
275
438
EXAMPLE: A camera that requires 5 VA and is installed 224 feet (68 m) from the transformer would require
a minimum wire gauge of 24 AWG.
[ 10 ]
Pelco Manual C2914M-F (08/05)
RJ45-10 Connections
The RJ45-10 connector allows video (composite and twisted pair) and power connections to be made to the
camera using a single Cat5-style cable.
NOTE: The PCM150 camera mount is designed for the CC3610 and CC3710 Series camera. It comes with
preconfigured auxiliary connectors and cables as well as an easy-to-wire adapter plate.
Before installation, identify the RJ45-10 connector leads to be used. To create the connection you will need a
Cat5 cable with the appropriate number of pairs and an 8-way or 10-way RJ45-10 connector. You will also need
a crimping tool capable of cutting, stripping, and crimping RJ50 (10P10C) connectors.
Wire the cable and connectors according to Table C. (More information about wiring each pair of leads appears
in the text below the table.) Then plug the auxiliary connector into the camera.
Figure 4. RJ45-10 Connector
Table C. RJ45-10 Pinouts
PINS
8-WAY
10-WAY
1
2
3
4
5
6
7
8
-
1
2
3
4
5
6
7
8
9
10
FUNCTION
No connection
Composite video ground
Composite video
No connection
Twisted pair video output (-)
Twisted pair video output (+)
No connection
24 VAC *; 12 VDC (-)*
24 VAC *; 12 VDC (+)*
No connection
* CC3610H-6, CC3610H-6X, CC3710S-6, CC3710S-6X, CC3710H-6 and CC3710H-6X models only
The following instructions apply to 10-way connectors. When using an 8-way connector, refer to table C.
Composite Video Out
Pins 2 and 3 provide a composite video output signal.
NOTE: The RJ45-10 composite video out is only intended to be used to route the video signal to a break-out
box where a conventional coaxial connection will be made.
Pelco Manual C2914M-F (08/05)
[ 11 ]
To send composite video through the RJ45-10 connector:
1. Connect composite video out to pin 3.
2. Connect composite video ground to pin 2.
Unshielded Twisted Pair (UTP)
Pins 5 and 6 allow video to be transmitted over unshielded twisted pair (UTP) wiring to equipment fitted with a
suitable receiver. Ensure that connection polarity is observed in relation to the connected twisted pair receiver.
To implement UTP, you must use 5-pair unshielded twisted cable, Cat5e, or an equivalent. The camera has a
built-in transmitter for UTP. However, you must provide a UTP receiver. Your maximum cable distance depends
on whether you install a passive or active receiver. When outputting composite video through the BNC or RJ4510, do not send UTP output to a passive UTP receiver. However it is acceptable to use an active UTP receiver
for UTP output in combination with the other video connections.
To send UTP video through the RJ45-10 connector:
1. Connect UTP+ video output to pin 6.
2. Connect UTP- video output to pin 5.
24 VAC/12 VDC Power Connection
Pins 8 and 9 allow connection to a power supply of 10.8 to 13.8 VDC (12 VDC -10% +15%) or 20.4 to 27.6 VAC
(24 VAC ±15%) at 50/60Hz. Correct connections and polarity must be observed.
WARNING: When powering the camera via the RJ45-10 connector, ensure that the power
connections to the screw terminals on the rear of the camera are not used. The power supply must
be a UL Listed Class 2 isolated type.
Service Connection
The service connector allows a video monitor to be connected locally to the camera using a 2.5 mm plug to
composite video BNC cable.
Figure 5. Service Connector
NOTE: Inserting the plug into the service connector disconnects video from the composite BNC connector on
the rear panel of the camera.
[ 12 ]
Pelco Manual C2914M-F (08/05)
CAMERA SETUP
Lens Setup and Focus Procedures
Video Drive or Direct Drive (DC) Auto Iris Lens
1. Set the ESC switch and AGC switch to OFF.
2. Adjust the lens for the optimum picture.
Video Drive Refer to the lens instructions and adjust the lens for the optimum picture (video output level
of 1 V peak-to-peak).
Direct Drive Use an appropriate screwdriver to turn the lens level potentiometer (refer to Figure 1) fully
clockwise. Next, slowly adjust the potentiometer counterclockwise until the optimum picture is obtained
(video output level of 1 V peak-to-peak).
3. Set the AGC switch to ON.
4. To focus, fully open the iris by covering the lens with a suitable neutral density (ND*) filter.
5. Select the scene to be viewed.
6. If the viewed scene is 6.5 feet (2 m) away or farther, set the lens focus to infinity (far).
7. Use the back focus adjustment ring (refer to the Back Focus Adjustment section) and focus on the
selected scene.
8. Remove the ND filter and set the lens focus as required.
Fixed Lens
1. Set the ESC switch and AGC switch to ON.
2. To focus, set the lens focus to infinity (far) and view an image greater than 6.5 feet (2 m) away.
3. Focus the image with the back focus adjustment ring (refer to the Back Focus Adjustment section).
4. Set the lens focus as required.
Manual Iris Lens
1. Set the ESC switch and AGC switch to OFF.
2. To focus, open the iris fully and set the lens focus to infinity.
3. View an image greater than 6.5 feet (2 m) away.
4. Focus the image with the back focus adjustment ring (refer to the Back Focus Adjustment section).
5. Adjust the lens focus and set the iris for the best picture quality. The largest aperture gives the best light
sensitivity, the smallest aperture the greatest depth of field.
6. Set the ESC switch and AGC switch to ON.
Zoom Lens
1. Set the lens focus to infinity (far) and fully open the iris by covering the lens with a suitable neutral
density (ND*) filter.
2. Zoom out to the widest field of vision and view a distant object.
3. Adjust the back focus adjustment ring until the object is in focus (refer to the Back Focus Adjustment
section).
4. Next zoom fully in and adjust the lens focus until the object is again focused.
Repeat these steps until the full zoom range may be viewed with the minimum loss of focus.
Figure 6. AGC and ESC Switch Settings
(White indicates switch position)
*NOTE: For best results outdoors use an ND3 (neutral density) filter.
Pelco Manual C2914M-F (08/05)
[ 13 ]
Back Focus Adjustment
The back focus adjustment is located at the front of the camera and is accessible from either side of the case.
To adjust the back focus:
1. Loosen the two back focus locking screws (one on each side).
2. Turn the back focus ring counterclockwise until the CCD sensor assembly is as far away from the back of
the lens as possible.
3. Turn the back focus ring clockwise until focus is achieved.
4. When the back focus adjustment is satisfactory, tighten the locking screws. Do not over-turn or force the
back focus adjustment ring.
NOTE: Always turn the back focus ring such that during focussing, the CCD sensor assembly is brought
towards the back of the lens (that is, clockwise). If the point of best-focus is passed, repeat the back focus
procedure from step 2.
Figure 7. Back Focus Adjustment
[ 14 ]
Pelco Manual C2914M-F (08/05)
Switch Settings
Figure 8. Switch Settings
(White indicates default switch position.)
NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch
before making any adjustments.
AGC (Automatic Gain Control) - Switch Setting 1
Automatically adjusts the image to compensate for low levels of illumination. Choose
between the following settings:
ON (Default setting) - Enables the AGC mode.
OFF - Disables the AGC mode.
ESC (Electronic Shutter Control) - Switch Setting 2
The ESC feature compensates for an excessive light level by automatically adjusting
the shutter speed. Choose between the following settings:
ON - Enables the Electronic Shutter Control mode.
OFF (Default setting) - Disables the Electronic Shutter Control mode.
BLC (Backlight Compensation) - Switch Setting 3
The BLC (Backlight Compensation) feature compensates for backlit scenes by
enhancing objects in the center of the scene that would previously have been in
silhouette. BLC will only function with a manual iris lens when the Electronic Shutter
Control feature is switched on. For direct drive and auto iris lenses, BLC will still function even though the Electronic Shutter Control feature is switched off. Choose between
the following settings:
ON - Enables the BLC mode.
OFF (Default setting) - Disables the BLC mode.
Pelco Manual C2914M-F (08/05)
[ 15 ]
Flickerless - Switch Setting 4
The flickerless setting can reduce the flicker caused by certain lighting conditions. The
Electronic Shutter Control must be off for the correct operation of the flickerless function
and is therefore automatically disabled. Choose between the following settings:
ON - Enables the Flickerless mode.
OFF (Default setting) - Disables the Flickerless mode.
INT/LL Synchronization Selection - Switch Setting 5
Line lock (LL) locks the frame rate to the power supply frequency. Eliminates vertical roll
caused by multiple cameras connected to the same switching device. Each camera
output is synchronized to the frequency of the power supply. Set the camera synchronization mode to one of the following:
INT - Disables line lock and cameras will synchronize internally. Regardless of the DIP
switch setting, cameras switch to this mode when a DC power supply is detected.
LL (Default setting) - Line locks frame rate of cameras.
White Balance - Switch Setting 6
Two white balance modes can be selected using this switch. For the majority of
applications, the AUTO setting will provide excellent color rendition and is the default
setting. However, there may be instances where it is necessary to set the white balance
manually. To do this, set the switch to MAN.
To adjust the white balance manually, position a white object in the camera field of view.
Once positioned, press and hold the WB Set button on the rear of the camera until the
white balance converges to give the correct rendition of white.
[ 16 ]
Pelco Manual C2914M-F (08/05)
Camera Synchronization
When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera
view is switched. To eliminate this vertical roll, it is necessary for the cameras to be synchronized. If the cameras
are connected to certain Pelco matrix products, the cameras will automatically lock to the pulse signal that is
transmitted up-the-coax. If not, it will be necessary to synchronize manually.
Cameras can be line locked or synchronized internally. Select the preferred method using the INT/LL DIP
switch on the rear of the camera (refer to the Switch Settings section).
If a camera is connected to a DC power supply, the camera will switch to Internal (INT) mode, regardless of the
DIP switch setting.
Internal (INT) mode should be selected when a noisy AC power supply is being used.
It may be necessary to have two people in communication when line locking cameras: one person at the
camera and another person at the monitor to observe the vertical roll and the effect of any adjustments made at
the camera.
To line lock the cameras, do the following:
1. Set the INT/LL DIP switch to LL.
2. Choose a reference camera to which all other cameras will be phased.
3. Select a camera and synchronize it to the reference camera, using the advance and retard buttons on the
rear of the camera (refer to Figure 1) to adjust the point on the AC cycle at which the cameras trigger.
4. Each time an adjustment is made, switch back and forth between the camera you are adjusting and the
reference camera. Repeat this process as many times as necessary until the roll between the cameras is
no longer noticeable.
5. Adjust the phase of all other cameras by repeating steps 3 and 4. Always adjust to the reference camera
selected in step 2.
NOTE: The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the
vertical sync pulses of the reference camera to the selected camera or cameras.
Pelco Manual C2914M-F (08/05)
[ 17 ]
SPECIFICATIONS
GENERAL
Imaging Device:
Picture Elements
CC3710H and CC3610H:
CC3710S:
Sensing Area:
Scanning System
NTSC:
PAL:
Synchronization System:
Horizontal Resolution
CC3610H models:
CC3710S models:
CC3710H models:
Iris Control:
Electronic Shutter Range
NTSC:
PAL:
Auto Iris Lens Type:
Minimum Illumination
CC3610H models:
CC3710S models:
CC3710H models:
Signal-to-Noise Ratio:
Vertical Phase:
Automatic Gain Control:
Electronic Shutter Control:
Backlight Compensation:
Flickerless Mode:
Internal Sync:
Auto White Balance:
Signal Processing:
Video Output:
Auto White Balance Range:
Gamma Correction:
ELECTRICAL
Power Requirements
Low Voltage Models:
High Voltage Models:
Power Consumption:
Power Connector
Low Voltage Models:
High Voltage Models:
Video Connector:
Service Connector:
Lens Jack:
[ 18 ]
Pelco Manual C2914M-F (08/05)
1/3-inch interline transfer CCD
NTSC 768 (H) x 494 (V); PAL 752 (H) x 582 (V)
NTSC 510 (H) x 492 (V); PAL 500 (H) x 582 (V)
6 mm diagonal
525 lines, 2:1 interlace
625 lines, 2:1 interlace
AC line lock/internal
480 TV lines
330 TV lines
480 TV lines
Selectable on/off
1/60-1/100,000 second
1/50-1/100,000 second
DC/video drive (automatic sensing)
0.4 lux at F1.2, 40 IRE, AGC on
0.6 lux at F1.2, 40 IRE, AGC on
0.7 lux at F1.2, 40 IRE, AGC on
>50 dB
Adjustable ±180°
On/off switchable
On/off switchable
On/off switchable
On/off switchable
On/off switchable
On/off switchable
Digital Signal Processing (DSP)
1 Vp-p, 75 ohms
2,500°K to 9,500°K
0.45
24-28 VAC ± 10% or 12-36 VDC ± 10%
110-240 VAC ± 10%
5 watts
2-pin terminal strip, RJ45-10 connector
Integral power cable
Composite via BNC, composite and twisted-pair via RJ45-10
2.5 mm jack for optional ICS090-SC service/monitor cable
(compatible with any standard monitor BNC connector)
4-pin connector (miniature square)
MECHANICAL
Lens Mount:
Camera Mount:
C/CS mount (adjustable)
1/4 –inch UNC-20 screw, top or bottom of camera housing
ENVIRONMENTAL
Operating Temperature:
Storage Temperature:
Operating Humidity:
Storage Humidity:
14° to 122°F (-10° to 50°C)
14° to 158°F (-10° to 70°C)
20% to 80%, non-condensing
20% to 90%, non-condensing
PHYSICAL
Dimensions:
Weight (without lens):
5" L x 2.9" W x 2.6" H (12.8 x 7.2 x 6.7 cm)
0.8 lb (0.4 kg)
(Design and product specifications subject to change without notice).
Pelco Manual C2914M-F (08/05)
[ 19 ]
[ 20 ]
Pelco Manual C2914M-F (08/05)
Pelco Manual C2914M-F (08/05)
[ 21 ]
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date
of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
• Two years on Spectra®, Esprit®, ExSite™, and PS20 Scanners, including when used in continuous motion applications.
• Two years on Esprit® and WW5700 series window wiper (excluding wiper blades).
• Two years (except lamp and color wheel) on Digital Light Processing (DLP™) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based
video products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan
modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA),
and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received
by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
[ 22 ]
Pelco Manual C2914M-F (08/05)
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual #
C2914M
C2914M-A
C2914M-B
C2914M-C
C2914M-D
C2914M-E
C2914M-F
Date
05/04
07/04
09/04
11/04
11/04
12/04
08/05
Comments
Original version.
Lens connector pin out changed.
Clarified instructions for UTP use.
Added UL warning for high-voltage models.
Revised safety instructions.
Revised back focus instructions and table C.
WEEE directive added.Warranty and return information amended.
Pelco Manual C2914M-F (08/05)
[ 23 ]
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
9001
ISO9001
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East
C2914M-F (08/05)
[ 24 ]
Pelco Manual C2914M-F (08/05)