Operating instructions | AGFA AP DC-733i Black Digital Camera User Manual

Thank you for purchasing this AGFAPHOTO digital camera. Please read these operating
instructions carefully in order to use the digital camera correctly. Keep the instructions in a safe
place after reading so that you can refer to them later.
Precautions
•
Do not aim the camera directly into the sun or other intense light sources which could
damage your eyesight.
•
Do not try to open the case of the camera or attempt to modify this camera in any way.
High-voltage internal components create the risk of electric shock when exposed.
Maintenance and repairs should be carried out only by authorized service providers.
•
Do not press the flash too close to the eyes of animals or young children. Eye damage may
result. Please remain at least one meter away from infants when using flash.
•
Keep the camera away from water and other liquids. Do not use the camera with wet hands.
Never use the camera in the rain or snow. Moisture creates internal danger and may cause
electric shock.
•
Keep the camera and its accessories out of the reach of children and animals to prevent
accidents or damage to the camera.
•
If you notice smoke or a strange odor coming from the camera, turn the power off immediately.
Take the camera to the nearest authorized service center for repair. Never attempt to repair
the camera on your own.
•
Use only the recommended power accessories. Use of power sources not expressly
recommended for this equipment may lead to overheating, distortion of the equipment, fire,
electrical shock or other hazards.
Disclaimer
We assume no responsibility over and above the provisions of the Product Liability Law for
damages suffered by the user or third parties as a result of inappropriate handling of the product
or its accessories, or by their operational failure and by their use. We reserve the right to make
changes to this product and its accessories without prior notice.
Warning!
Never disconnect to open the camera or remove any parts of it. This will invalidate all guarantee
claims.
Using your batteries
For best performance and prolonged battery life, we recommend the use of AA lithium or
rechargeable NiMH batteries.
Extending battery life
The following functions use up a great deal of battery power and should therefore only be used
occasionally:
1
•
Excessive use of flash
•
Editing images on the camera display
The battery life can be affected by soiling. Please clean the contacts with a clean and dry cloth
before putting the batteries in the camera. Battery performance drops at temperatures below 5 °C
(41 °F). If you use the camera at low temperatures you should have replacement batteries to
hand and ensure they do not get too cold. Please note: you should not dispose of cold and
seemingly flat batteries because these batteries may work again at room temperature.
2
Parts of the Camera
1. Flash
2. Microphone
3. Lens
4. Self-timer Lamp
5. Zoom Button
y
Thumbnail
y
Playback Zoom
6. Playback Button
7. Menu Button
8. Operation Lamp
9. Mode Button
10. Delete Button
11. LCD Monitor
12. SET/DISP Button
13. Flash Button
14. Macro Button
3
15. Strap Ring
16. Shutter Button
17. Power Button
18. Speaker
19. USB/AV Terminal
21. Battery Cover
22. Tripod Socket
4
Changing the Mode
You can record images and voices in the REC mode. And using the PLAYBACK mode to replay,
delete, or edit images on the LCD monitor.
Switching between REC mode and PLAYBACK mode
In REC mode: press the PLAYBACK button (n)
to switch to the PLAY mode.
In PLAY mode: press the PLAYBACK (n) or the
MODE (o) button to switch to the REC mode.
Selecting the REC mode
1
2
Set the camera to the REC mode
Launch the mode palette.
y
Press the MODE button (o) to show
the scene mode palette.
3
Select a mode.
y
Use the four-way control to select a
desired mode and press the SET
button to confirm the setting.
5
Using the Menus
When a menu is displayed, the four-way control and the SET button are used to make the desired
settings.
REC menu
1
Turn the power on, and set the camera
to the REC mode.
2
Open the REC menu.
y
Press the MENU button to display
the menu.
3
4
Select an item.
Press
or
to select a menu item.
Change the setting.
Press
5
or
to change the setting.
Press the MENU or the SET button to save the settings and close the menu.
Setup menu
1
Turn the power on, and set the
camera to the REC or PLAYBACK
mode.
2
Press the MENU button to open the
REC or PLAYBACK menu.
y
The menu displays depends on
whether you are in the REC mode
or the PLAY- BACK mode.
3
Open the Setup menu.
y
Press four-way control to select SETUP (
display the Setup menu.
6
) and then press the SET button to
4
Select an item.
y
or
Press
to select a menu item and then press
or the SET button to launch
the submenu.
5
Change the setting.
y
Press
or
to select an option and press
or the SET button to apply the
setting.
6
Press the MENU button to close the menu.
Deleting a Single File
1
Turn the power on, and set the camera
to the PLAYBACK mode.
2
Open the menu.
y
Press the MENU button (n), then
use the four-way control (o) to
select Delete (
) and press the
SET button (o).
3
Press
or
(o) to select [SINGLE], and then press the SET button (o).
4
Press
5
Press the SET button (o) to delete the image.
y
or
(o) to select the image you want to delete.
Repeat step 4~5 to delete images.
~ When the O/S is Windows 98/98SE, use mouse right click on the program file named "DSC
driver" or "DSC User manual" located in the CD-ROM.
7
Customer care
More information con the complete AGFAPHOTO digital camera product range can be found under
www.plawa.com
Service & Repair Hotline (EU):
00800 752 921 00 (from a landline only)
Service & Support Hotline (Germany):
0900 1000 042 (1.49 Euro/ min. from a German landline only)
Online Service / International contact:
support-apdc@plawa.com
Manufactured by
plawa-feinwerktechnik GmbH & Co. KG
Bleichereistraße 18
73066 Uhingen
Germany
AGFAPHOTO is used under license of Agfa-Gevaert NV & Co. KG. Agfa-Gevaert NV & Co. KG. does
not manufacture this product or provide any product warranty or support. For service, support and
warranty information, contact the distributor or manufacturer. Contact: AgfaPhoto Holding GmbH,
www.agfaphoto.com
8
Disposal of Waste Equipment by Users in Private Households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
Batteries and rechargeable batteries should not be thrown in the trash can. Please return used batteries
to the store or take it to where they collets such items. Following this guideline we are helping not to
polluting our environment.
FCC Compliance and Advisory
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.) this device may not cause harmful interference, and 2.) this device must accept any interference
received, including interference that may cause unsatisfactory operation. This equipment has been
tested and found to comply with the limits for a Class B peripheral, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. When shielded interface cables have
been provided with the product or when specified additional components or accessories have
elsewhere been designated to be used with the installation of the product, they must be used in
order to ensure compliance with FCC regulations.
9
Download PDF

advertising