Owner`s manual | AGFA ATCA-C110/1G Automobile Accessories User Manual

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
DV36
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
DIRECT VENT FIREPLACE
BY: SHERWOOD INDUSTRIES LTD
OWNER’S MANUAL
WHAT TO DO IF YOU SMELL GAS
• Open windows/extinguish any open
flame.
• Do not try to light any appliance.
• Do not touch any electrical switch or
use any phone in your building.
• Immediately call your gas supplier
from a neighbour’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapours and liquids in the
vicinity of this or any other appliance.
WARNING
If the information in this manual
is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of
life. Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
This appliance may be installed in an after-market
permanently located, manufactured (mobile)
home, where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
Massachusetts installations (Warning): This product must be installed by a licensed
plumber or gas fitter when installed within the Commonwealth of Massachusetts.
Other Massachusetts code requirements: Flexible connector must not be longer than
36in., a shut off valve must be installed; only direct vent sealed combustion products
are approved for bedrooms/bathrooms. A carbon monoxide detector is required in all
rooms containing gas fired direct vent appliances.
50-927
Safety Precautions
FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER,
PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:
• All ENVIRO gas-fired appliances must be installed
in accordance with their instructions. Carefully read all
the instructions in this manual first. Consult the building
authority having jurisdiction to determine the need for
a permit prior to commencing the installation.
• NOTE: Failure to follow these instructions could
cause a malfunction of the fireplace, which could
result in death, serious bodily injury, and/or property
damage.
• Failure to follow these instructions may also void
your fire insurance and/or warranty.
GENERAL
• Installation and repair should be done by a
qualified service person. The appliance should be
inspected before the first use and, at least, annually
by a qualified service person. More frequent
cleaning may be required due to excessive lint from
carpeting, bedding material, etc. It is imperative the
control compartments, burners and circulating air
passageways of the appliance be kept clean.
• Due to high temperatures, the appliance should
be located out of high traffic areas and away from
furniture and draperies.
Children and adults should be alerted to the
hazards of high surface temperatures and
should stay away to avoid burn or clothing
ignition.
• Young children should be carefully supervised
when in the same room as the appliance.
• Clothing or other flammable materials should not
be placed on or near the appliance.
FOR YOUR SAFETY
• Installation and service must be performed by a
qualified installer, service agency or gas supplier.
• This installation must conform to local codes or, in
the absence of local codes, to the current CAN/CGAB149 installation code (Canada) or National Fuel Gas
Code ANSI Z223.1.2 (USA)
2
• To prevent injury, do not allow anyone who is
unfamiliar with the stove to operate it.
• To prevent injury, if the pilot or pilot and
burners have gone out on their own, open the
glass door and wait 5 minutes to air out before
attempting to re-light the stove.
• Always keep the area around these appliances
clear of combustible material, gasoline and other
flammable liquids and vapours.
• These appliances should not be used as a drying
rack for clothing or for hanging Christmas stockings/
decorations.
• Due to the paint curing on the stove, a faint odor
and slight smoking will likely be noticed when the
stove is first used. Open a window until the smoking
stops.
Always connect this gas stove to a vent system and
vent to the outside of the building envelope. Never
vent to another room or inside the building. Make sure
the specified vent pipe is used, properly sized and of
adequate height to provide sufficient draft. Inspect
the venting system annually for blockage and signs of
deterioration.
WARNING: Failure to position the parts in accordance
with the diagrams in this booklet, or failure to use only
parts specifically approved with this appliance, may
result in property damage or personal injury.
WARNING: Do not operate with the glass front
removed, cracked or broken. Replacement of the
glass should be done by a licensed or qualified service
person.
• Never use solid fuels such as wood, paper,
cardboard, coal, or any flammable liquids, etc., in this
appliance.
• Do not use this heater if any part has been under
water. Immediately call a qualified service technician
to inspect the heater and to replace any part of the
control or gas control systems that have been under
water.
• Do not abuse the glass by striking it or slamming
the door shut.
Table of Contents
Safety Precautions........................................................................................................2
Table of Contents.........................................................................................................3
Codes And Approvals....................................................................................................4
Specifications.............................................................................................................5
Dimensions.....................................................................................................5
Rating Label Location.........................................................................................5
Operating Instructions..................................................................................................6
Pilot Lighting Instructions...................................................................................6
Pilot Light.........................................................................................................7
Air Shutter.........................................................................................................7
Remote Controls................................................................................................7
Burner Lighting.................................................................................................8
Blower Speed (Optional).....................................................................................8
Normal Sounds During Operation........................................................................8
Maintenance And Service..............................................................................................9
Routine Maintenance..........................................................................................9
Cleaning The Glass............................................................................................9
Cleaning The Firebox.........................................................................................9
Replacing the Glass...........................................................................................9
Cleaning Decorative Surfaces............................................................................10
Glass Door Removal.........................................................................................10
Burner Removal...............................................................................................11
Fuel Conversion...............................................................................................11
Initial Installation.......................................................................................................14
Introduction.................................................................................................14
Placement and Framing....................................................................................14
Framing Mount Brackets...................................................................................15
Corner Installation...........................................................................................15
Raised Fireplaces and Hearths..........................................................................15
Mantel Clearances...........................................................................................16
Vent Termination Restrictions............................................................................17
Fireplace Horizontal Vent Kit 50-1235................................................................18
Other Approved Vent Parts...............................................................................19
Venting........................................................................................................21
Vent Configurations and Restrictor Settings.......................................................22
Horizontal Termination.....................................................................................23
Vertical Termination.........................................................................................24
Installation Of Electrical Wiring For The Optional Fan Kit.....................................27
Electrical System For Thermostat......................................................................27
Gas Line Connection and Testing.......................................................................28
Secondary Installation................................................................................................29
Log Set and Ember Installation.........................................................................29
Optional Ceramic Brick Panel Installation............................................................32
Optional Fan Kit Installation..............................................................................33
Secondary Installation................................................................................................34
Trouble Shooting........................................................................................................35
Parts List....................................................................................................................36
Parts Diagram............................................................................................................37
Warranty.................................................................................................................38
Installation Data Sheet...............................................................................................39
3
Codes And Approvals
DIRECT VENT ONLY: This type is identified by the prefix DV. This appliance draws all of its air for
combustion from outside the dwelling, through a specially designed vent pipe system.
This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above
sea level.
In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas
Association guidelines which state: the sea level rated input of Gas Designed Appliances installed at
elevations above 2000 (610 m) feet is to be reduced 4% for each 1000 feet (305 m) above sea level.
Refer also to local authorities or codes which have jurisdiction in your area regarding the de-rate
guidelines.
In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certified high
altitude rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).
•
This appliance has been tested by INTERTEK (Warnock Hersey) and found to comply with the
established VENTED GAS FIREPLACE HEATER standards in CANADA and the USA as follows:
VENTED GAS FIREPLACE HEATER (DV36; NG/LPG)
TESTED TO: ANSI Z21.88a-2003/CSA 2.33a-2003 VENTED GAS FIREPLACE HEATERS
CAN/CGA 2.17-M91 GAS FIRED APPLIANCES FOR HIGH ALTITUDES
CSA P.4.1-02 TESTING METHOD FOR MEASURING ANNUAL FIREPLACE EFFICIENCY
This ENVIRO DV36 Fireplace:
• Has been certified for use with either natural or propane gases. (See rating label.)
• Is not for use with solid fuels.
• Is approved for bedroom or bed sitting room. (IN CANADA: must be installed with a listed wall
thermostat. IN USA: see current ANSI Z223.1 for installation instructions.)
• Must be installed in accordance with local codes. If none exist, use current
installation code CAN/CGA B149 in Canada or ANSI Z223.1/NFPA 54 in the
USA.
• Must be properly connected to an approved venting system and not connected
to a chimney flue serving a separate solid-fuel burning appliance.
• Can be used with an optional fan kit (part number 50-925); if so, an
electrical receptacle box and 14/3 wire power cable must be wired to the
appliance upon installation.
IMPORTANT NOTICE (Regarding first fire up): When the unit is turned
on for the first time, it should be turned onto high without the fan on for
the first 4 hours. This will cure the paint, logs, gasket material and other
products used in the manufacturing process. It is advisable to open a
window or door, as the unit will start to smoke and can irritate some people.
After the unit has gone through the first burn, turn the unit off including the
pilot, let the unit get cold then remove the glass door and clean it with a
good gas fireplace glass cleaner, available at your local ENVIRO dealer.
4
Specifications
INSTALLATION OPTIONS:
• Parallel to a wall or placed in a corner
• Vertical or horizontal venting
• With a floor hearth or raised up the wall
WARNING:
Operation of this heater when not connected to a properly installed and maintained venting system can
result in carbon monoxide (CO) poisoning and possible death.
DIMENSIONS:
� ����
�������
�� �����
�������
�� ����
�������
� ���
�������
�
��
������
� ����
�������
�� �����
�������
� ����
�������
�� �����
�������
�� ����
�������
�� ����
�������
�� ����
�������
����������
������
�� ����
�������
�� ����
�������
��� ����
������
� �����
������
� ������
�������
�� �����
�������
� �����
������
� ������
�������
�� ����
�������
Figure 1. Dimensions of the Firebox.
RATING LABEL LOCATION:
The rating label is located under the control panel and is attached to a rectangular metal sheet that is
chained to the fireplace.
5
Operating Instructions
For Your Safety, Read Safety Precautions And
Lighting Instructions Before Operating
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY
RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.
PILOT LIGHTING INSTRUCTIONS:
CAUTION:
Hot while operating. Do not touch. Severe burns may result. Keep children,
clothing, furniture, gasoline or other flammable vapors away.
CAUTION: Do not operate this fireplace with the glass removed, cracked or broken. Replacement of the panel(s) should
be done by a licensed or qualified person! This appliance needs fresh air for safe operation and must be installed with
provisions for combustion and ventilation air. See installation and operating instructions manual. Keep burner and control
compartment clean.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage, or
loss of life. Refer to owner's information manual provided with this appliance. For assistance or additional information
consult a qualified installer, service agency or the gas supplier.
Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
FOR YOUR SAFETY READ BEFORE
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
A) This appliance is equipped with a pilot, which must be lit by
hand by following these instructions exactly.
B) BEFORE LIGHTING smell all around the appliance area for
gas and next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance. Do not touch any electrical
switch: do not use any phone in your building. Immediately call
your gas supplier from a neighbors' phone. Follow the gas
suppliers instructions. If you cannot reach your gas supplier, call
the fire department.
C) Use only your hand to push in or turn the gas control knob;
NEVER use tools. If the knob will not push in or turn by hand,
do not try to repair it. Call a qualified service technician.
Force or attempted repair may result in a fire or explosion.
D) Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Turn off all electrical power to this appliance.
3. Turn the gas control knob clockwise
to the off position.
4. Open door. Wait five (5) minutes to clear out any gas. Close
door. If you smell gas STOP! Follow “B” in the above safety
information. If you do not smell gas go to the next step.
5. Find pilot-located to the right behind the side log. Turn the gas
control knob counter-clockwise
to “PILOT”. Push the
gas control in fully and hold. Keep knob depressed
for about 30 seconds after pilot is lit. Release knob.
If pilot goes out, repeat steps 4 through 5.
WARNING: this gas valve has a lockout device, which will
not allow the pilot burner to be relit until the thermocouple
has cooled. If the knob does not pop up when released,
stop and immediately call your service technician or gas
supplier.
If the pilot does not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician or
gas supplier.
6. Turn the gas control knob counter clockwise
to the
“ON” position. Flip the burner switch to “ON” THEN TURN
THE “HI/LOW” knob to the desired setting.
7. Turn on the electrical power to the unit.
TO TURN OFF GAS TO APPLIANCE
1. Flip burner switch to “OFF”
2. Turn the gas control knob clockwise
position
to the “OFF”
3. Turn off all electrical power to the appliance if service is to
be performed.
�������
Figure 2. Lighting Instruction Label
6
Operating Instructions
PILOT LIGHT:
1. Turn off the gas to the fireplace. If not recently done, remove the glass and let the unit air out
for at least five (5) minutes to clear out any gas. Turn on gas to the heater. Leak test all joints
with soapy water. NEVER USE OPEN FLAME FOR LEAK TESTING.
2. Start the pilot by pressing the gas control knob and turning it to PILOT.
While holding the gas control knob in, press the piezo ignitor several
times until the pilot light starts. Hold the gas control knob in for 30
seconds. Check that the pilot has fully engulfed the thermocouple
assembly (see Figure 3).
����������
������������
3. Start the main burner by turning the gas control knob to ON and then
turn the rocker switch to ON. Check that all burner ports have flame.
4. Leak test all gas joints again.
Figure 3. Pilot Flame
AIR SHUTTER:
The air shutter adjustment lever is centered above the controls (see Figure 4).
The air shutter allows the amount of air coming into the fireplace to be adjusted in order to accommodate
different climates and venting arrangements. Start the pilot and then the burner. Make sure the pilot
flame is burning normally and none of the burner ports are plugged. Let the fireplace burn for roughly
fifteen minutes and then examine the flames, compare the flames to Figure 40.
The ideal flame will be blue at the base and light orange above. The flames should be of medium height.
If the flames look like this, no venturi adjustment is needed. If the flames are fairly short and mostly
blue, the fireplace is getting too much
air. Therefore, the air shutter should be
��� �������
closed (push in) slightly until the correct
flames are achieved. Flames that are
���� ��� � ����
very orange, with tall, dark, stringy tips,
are not getting enough air. Open (pull
out) the venturi until the flames clean
���� ��� � �����
up. If the venturi is opened, or closed all
the way, and the correct flames cannot
be attained, turn off the gas and contact
the dealer.
Figure 4. Air shutter adjustment lever.
Warning: Incorrect venturi adjustment
may lead to improper combustion, which
is a safety hazard. Contact the dealer if
there is any concern about the venturi
adjustment.
REMOTE CONTROLS:
This fireplace can use an optional remote control or an optional cordless wall thermostat. If either of
these are to be used to control the fireplace for the majority of the time, leave the ON/OFF switch (on the
control panel) in the remote/thermostat position. Consult the instructions included with the remote/wall
thermostat for operation guidelines.
7
Operating Instructions
For Your Safety, Read Safety Precautions And
Lighting Instructions Before Operating
BURNER LIGHTING:
A) Make sure the pilot is lit.
B) Turn gas control knob COUNTER CLOCKWISE to ON.
C) Flip the burner switch to ON.
D) Turn HI/LO knob to the desired flame height.
E) Turn on all electrical power to the unit.
NOTE: Check that all burner holes are lit.
TO TURN GAS FIREPLACE OFF:
���
�������
Flip switch to OFF to turn off burners only.
If the fireplace is to be turned off for the season,
or for servicing, turn the gas shut off valve to
OFF. DO NOT FORCE IT. If the unit is going to
be serviced, turn off the electrical power to the
unit as well.
����� �������
������
����
Figure 5. Control Panel
NOTE: When the unit is turned on for the first time, it should be turned onto high, with the fan OFF,
for the first two to four hours. This will cure the paint, logs, gasket material, and other products used
in the manufacturing process. It is advised that a door or window be opened as the unit will start to
smoke, which can irritate some people. After the unit has gone through the first burn, turn the unit OFF,
including the pilot, and let the unit get completely cold. Then remove the glass and clean it with a good
gas fireplace glass cleaner, available at your local Enviro dealer. See “MAINTENANCE AND SERVICE; GLASS
DOOR REMOVAL” and “MAINTENANCE AND SERVICE; CLEANING THE GLASS.”
BLOWER SPEED (OPTIONAL):
The blower will come on only when the fireplace is up to temperature
(approximately 20 minutes). The speed of the fan can be changed by turning the
fan control knob. To turn the blower off, turn the knob COUNTER CLOCKWISE
until it “clicks” off (Figure 6).
It is advisable not to operate the blower below 1/3 speed as it puts a strain on
the windings of the blower and running the blower at lower speeds could also
cause premature fan failure.
��
���
��
Figure 6. Fan Control
NORMAL SOUNDS DURING OPERATION:
Table 1: Normal Sounds
8
Component
Sound & Reason
DV36 & Fascia
Creaking when heating up or cooling down.
Burner
Light pop or poof when turned off; this is more common with LP units.
Temperature Sensor
Clinking when it senses to turn the blower on or off.
Pilot Flame
Quiet whisper while the pilot flame in on.
Blower / Fan
Air movement that increase and decreases with the speed of the blower. The
blower is pushing the heat from the fireplace into the room.
Gas Control Valve
Dull click when turning on or off, this is the valve opening and closing.
Maintenance And Service
ROUTINE MAINTENANCE:
At least once a year, run through the following procedures to ensure the system is clean and working
properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not
blocked by anything. The pilot flame should be blue with little or no yellow on the tips.
Warning: Clearances must be sufficient to allow access for maintenance and service
Warning: Failure to position the parts in accordance with this manual, or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
The venting system must be periodically examined; it is recommended the examination is done by a
qualified agency.
CLEANING THE GLASS:
When the fireplace has cooled, remove the face of the fireplace along with the glass. See MAINTENANCE
AND SERVICE - GLASS DOOR REMOVAL. Check the gasket material on the back of the glass, making sure that
it is attached and intact.
During a cold start up, condensation will sometimes form on the glass. This is a normal condition with all
fireplaces. However, this condensation can allow dust and lint to cling to the glass surface. Initial paint
curing of the appliance can leave a slight film behind the glass, a temporary problem. The glass will need
cleaning about two weeks after installation. Use a mild glass cleaner and a soft cloth; abrasive
cleaners will damage the glass and plated surfaces. Depending on the amount of use, the glass
should require cleaning no more than two or three times a season. Do not clean the glass when it is
hot.
CLEANING THE FIREBOX:
Remove the logs carefully, as they are very fragile. Gently remove all the embers and rock wool and place
on a paper towel. Vacuum the bottom of the firebox thoroughly. Carefully clean any dust off the logs and
remove any lint from the burner and pilot. At this time, inspect the burner pan for cracking or severe
warping. If a problem is suspected, contact the dealer. Check the logs for deterioration or large amounts
of soot; a small amount on the bottom side of the logs is normal. Replace the logs and embers as in the
SECONDARY INSTALLATION - LOG SET AND EMBER INSTALLATION section. If new/more embers and rock wool are
required, contact your nearest ENVIRO dealer.
REPLACING THE GLASS:
The glass in the fireplace is a high temperature ceramic. If the glass is damaged in any way, a factory
replacement is required (see PARTS LIST). Wear gloves when handling damaged glass door assembly
to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in
newsprint and tape and/or a strong plastic bag. Do not operate with the glass front removed, cracked
or broken. Removal and replacement of the glass from the door must be done by a licensed or qualified
service person. The glass must be purchased from an ENVIRO dealer. No substitute materials
are allowed.
9
Maintenance And Service
CLEANING DECORATIVE SURFACES:
Painted and porcelain faces should be wiped with a damp cloth periodically. If a plated face has been
purchased, it should be unpacked/unwrapped carefully to avoid getting anything on the surface of the
finish, including cleaners, polish and finger prints. It is important to note that fingerprints and other
marks can leave a permanent stain on plated finishes. To avoid this, give the face a quick wipe with
denatured alcohol on a soft cloth BEFORE lighting the fireplace. Never clean the face when it is
hot. Do not use other cleaners as they may leave a residue, which can become permanently etched into
the surface.
If your fingers come into contact with the antique copper finish, the oils left as fingerprints on the
copper can cause discoloration, which will eventually turn green in that area. You can clean the patina
or discoloured areas of the antique copper finish with “OO” 3M green sanding pads. These can be
purchased from most hardware stores. On the areas with discoloration, use the sanding pads to sand
in the same direction as the brushed finish, then blend the finish by feathering in the surrounding area.
This refinishing procedure has been approved by the manufacturer and will not harm the finish. Please
note: ANTIQUE COPPER IS THE ONLY FINISH THAT CAN BE SANDED, DO NOT SAND PEWTER, GOLD
OR NICKEL FINISHES.
GLASS DOOR REMOVAL:
Door latch
mechanism
Finger grooves
Door latch
mechanism
Figure 7. Bottom latches for glass.
Finger
grooves
In order to install the log set, and
for regular cleaning, the glass door
must be removed. There are two
(2) door latch mechanisms under
the glass door shown in Figure
7. Each latch has two (2) finger
grooves, use these to pull the
mechanisms straight out. When
the bottom latches are unhooked,
lift the door straight up over the
placement pins at the top of the
door, shown in Figure 8.
To replace the glass door, simply
reverse the above procedure.
Warning: Do not touch or attempt
to remove the glass if the fireplace
is not completely cold.
���� ��������� ����
Figure 8. Top pins for glass door.
10
WARNING:
Never
operate
the fireplace with the glass
removed.
Maintenance And Service
BURNER REMOVAL:
The burner may need to be removed for a few reasons, including cleaning under the burner, converting
the unit to a different gas type, or to replace the burner altogether. Proceed only when the unit has
completely cooled down.
1. Remove the fascia or louvers
2. Remove the glass as shown in the
MAINTENANCE AND SERVICE - GLASS DOOR
REMOVAL.
3. Remove the brick panels as shown
in SECONDARY INSTALLATION - OPTIONAL
CERAMIC BRICK PANEL INSTALLATION.
4. Remove the
corners.
left
and
right
firebox
5. Remove the six (6) T-20 screws that hold
the burner in place; three (3) along the
top and three (3) along the bottom.
6. Lift the burner straight up then out.
Figure 9. Removing Burner.
To re-install the burner follow steps 1-6 in reverse. When placing the burner back in the unit ensure that
the venturi box under the burner is lined up.
FUEL CONVERSION:
TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY
Please read and understand these instructions before installing.
Warning: This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturer’s instructions and all applicable codes and requirements of the
authority having jurisdiction. If the information in these instructions is not followed
exactly, a fire, explosion or production of carbon monoxide may result causing property
damage, personal injury or loss of life. The qualified service agency is responsible for
the proper installation of this kit. The installation is not proper or complete until the
operation of the converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
Kit Parts List:
1
1
1
1
-
Orifice (NG - #39 DMS or LP - #53 DMS)
Pilot Injector (NG 0.62 mm; LP 0.35 mm)
Installation instruction sheet
Conversion label
Carefully inspect all parts supplied with this conversion kit. If any parts have been damaged or are
missing, contact your dealer, distributor or courier company to have them replaced before starting this
installation.
11
Maintenance And Service
Conversion Kit Installation:
1.
Turn control knob on the gas valve to the “OFF” position and shut the gas supply off at the shut-off
valve upstream of the unit. CAUTION: The gas supply must be shut off prior to disconnecting the
electrical power and before proceeding with the conversion. Allow the valve and unit to cool down
to room temperature.
2.
Remove the glass as shown in the MAINTENANCE
3.
Carefully remove the log set and ember material if they are installed.
4.
Remove the burner as shown in the MAINTENANCE
5.
Convert the burner orifice(s):
AND
SERVICE - GLASS DOOR REMOVAL.
AND
SERVICE - BURNER REMOVAL.
a) Remove the main burner orifice with a 1⁄2 inch deep socket.
b) Put a bead of pipe-thread sealant or approved Teflon tape on the orifice threads before installing
into the brass elbow.
c) Install the new orifice(s) from the kit into the brass elbow.
6.
Convert the pilot injector:
a) Pull the pilot hood straight up to access the pilot injector.
b) Using a 5/32” or 4 mm Allen key, remove the pilot injector.
c) Install the new pilot injector supplied with this conversion kit. Simply
screw the new injector inside the pilot hood using the Allen key,
d) Reinstall the hood by placing the hood on the assembly, line up the key
way, and snap into place.
7.
Convert the SIT gas valve:
a) Remove the black protection cap from the HI/LO knob by hand shown in
Figure 10.
b) Insert a 5/32” or 4 mm Allen wrench into the
hexagonal key-way of the screw (see Figure 11),
rotate it counter-clockwise until it is free and
extract it.
Loosen
Tighten
Figure 10: Removing
valve cap.
c) Check that the screw is clean and if necessary
remove dirt.
d) Flip the screw (refer to Figure 12).
e) Using the Allen wrench as shown in Figure 11,
rotate the screw clockwise until a torque of 9
inch lbs. WARNING! Do not over tighten the
screw. It is recommended that you grip the
wrench by the short side.
Figure 11: Removing valve
screw.
12
f) Verify that if the conversion is from NG to LPG,
the screw must be re-assembled with the red oring visible (refer to Figure 13). If the conversion
is from LPG to NG, the red o-ring of the screw
must be not visible.
Figure 12: Flip valve
screw.
Maintenance And Service
Red o-ring
is visible
Red o-ring
is not visible
g) Re-attach the black protection
cap that was removed in step
a (Figure 10).
LPG Configuration
Figure 13: O-ring on valve screw.
8.
9.
Reinstall the burner, brick panels, log set, embers, and glass door.
Also refer to SECONDARY INSTALLATION - INSTALLING LOG SET AND EMBERS
in your Owner’s Manual. When re-installing the burner, ensure that
the burner to pilot hood relationship is similar to what is shown in
Figure 14. On some units you will need to pay special attention when
installing the burner that the venturi adjustment rod is properly
installed into the venturi adjustment piece welded to the burner
venturi tube
Figure 14. Ignitor assembly
beside the burner.
Reconnect the main gas line if it was disconnected and open the shut-off valve at the gas line to the
unit.
10. Use a small brush to apply a warm soapy water solution to all gas connections (use a half dish soap
and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by
using an approved pipe thread sealant or approved Teflon tape. NEVER USE AN OPEN FLAME WHEN
TESTING FOR LEAKS.
11. Reconnect the electrical power to the unit.
12. Relight the main burner in both the “HI” and “LO” positions to verify proper burner ignition and
operation and proper flame appearance. Also refer to SECONDARY INSTALLATION - INSTALLING LOG SET
AND EMBERS in your Owner’s Manual for a flame appearance picture.
13. MAKE SURE that the conversion label is installed on or close to the rating label to signify that the
unit has been converted to a different fuel type.
13
Initial Installation
QUALIFIED INSTALLERS ONLY
INTRODUCTION:
This section of the owner’s manual is for the use of qualified technicians only. Fireplace placement,
hearths, facing, mantels, and venting terminations will be covered, as well as the gas and electric
systems. There are several installation safety guidelines that must be adhered to. Please carefully read
the safety precautions at the front of this manual.
Warning: Clearances must be sufficient to allow access for maintenance and service.
PLACEMENT AND FRAMING:
Table 2. Framing Dimensions.
Firebox Framing
Depth
131⁄4”
Width
361⁄4”
Height
371⁄8”
Gas/Electrical Inlet:
Distance back
55⁄8”
Distance up
35⁄8”
������
� ����
�� ����
�� ����
�������
�������
��
���
��
�
�� ���
�������
����
14.3 cm
9.3 cm
The location for the fireplace can be along a
wall, raised or at floor level, or in a corner.
There are specific framing measurements for
each situation. The basic opening should have
the dimensions shown in Figure 15.
���
�����
� ����
33.7 cm
92.1 cm
94.4 cm
��
��
������
�������
Figure 15. Dimensions for Framing the Firebox.
The fireplace must have a strong and level
surface to be placed on. The surface should be
made of wood or a non-combustible material,
not carpet.
The framing boards may touch the top and
back standoffs, but no insulating material
can be placed between the frame and the
standoffs.
The gas line, 3⁄8 inch NPT, should be brought
to the right side of the fireplace. If this set up
is inconvenient, the electrical wire and the gas
line configuration can be reversed.
The location should be chosen so the fireplace will be at least 36 inches (91.4 cm) from drapes, doors
and other combustibles. The framed opening should also be a minimum of 1 inches (2.5 cm) from the
nearest perpendicular wall (sidewall to the edge of the opening).
The DV36 is designed so it can be installed at floor level without a required hearth.
14
Initial Installation
QUALIFIED INSTALLERS ONLY
FRAMING MOUNT BRACKETS:
Mount the two framing mount brackets on each side and secure the
fireplace to framing with screws or nails (refer to Figure 16). The brackets
will allow for a 1⁄2” (13 mm), 5⁄8” (16 mm), 3⁄4” (19 mm) thick finishing
wall. The wall may be finished up to the fireplace facing with combustible
material.
Figure 16. Nail Tab.
CORNER INSTALLATION:
The dimensions for installing a fireplace in the corner of a room are given in Figures 17 and 18. Refer to
“INITIAL INSTALLATION - VENT CONFIGURATIONS AND RESTRICTOR SETTINGS” for allowable pipe lengths.
Do not interfere with the structural integrity of the walls.
33 3/4”
15 1/2”
(856mm)
23 7/8” (393mm)
(605mm)
Outside Wall
(Thick)
11”
(279mm)
Inside
Wall
5 5/8”
(143mm)
36 1/4”
(920mm) 47 5/8”
(1210mm)
Figure 17. Dimensions for a corner installation, rear
vented.
Figure 18. Dimensions for a corner installation, top
vented.
RAISED FIREPLACES AND HEARTHS:
Figure 19. Raised Fireplace with Raised Hearth
Figure 20. Raised Fireplace with Floor Level Hearth
15
Initial Installation
QUALIFIED INSTALLERS ONLY
To Ceiling
Even though the DV36 can be installed at floor
level without a hearth, there are a few options
with raised fireplaces: raised with a floor level
hearth (Figures 19), raised with a raised hearth
(Figures 20), or raised with no hearth (Figures 21).
If the fireplace is raised, it cannot be placed within
37 inches (1.04 m) of the ceiling. When installing
a raised fireplace, it is imperative that the support
stand is strong enough to hold the weight of the
fireplace and venting.
37”
Figure 21. Raised Fireplace with no Hearth
MANTEL CLEARANCES:
It is not necessary to install a mantel, but if one is desired it is important to follow the guidelines.
Note: Louvers have different mantel clearances than when fascia or insets are installed.
Table 3: Mantel clearances.
Top of unit to horizontal framing
Louvers Only
Fascia or Insets
3” (7.6 cm)
3” (7.6 cm)
Top of unit to bottom of 3” (7.6 cm) mantel
12” (30.5 cm)
Top of unit to bottom of 31⁄2” (8.9 cm) mantel
8” (20.3 cm
Top of unit to bottom of 10” (254 mm) mantel
10” (25.4 cm
14” (35.6 cm)
Top of unit to bottom of 3⁄4” (19 mm) facing board
6” (15.2 cm)
6” (15.2 cm)
10" (254mm) mantle
Combustible board
3” (76mm) mantle
3"
(76mm)
3/4"
Top of unit
Combustible
front face
12"
(305mm)
3"
(76mm)
Figure 22. Combustible Shelf Clearance.
A shelf may be installed above the unit. We
recommend that no heat sensitive items or
components be placed on the shelf (see
Figure 22).
16
14"
(356mm)
(19mm) facing board
6"
(152mm)
Top of unit
Combustible front face
Figure 23. Combustible Mantel Clearances for Fascia or
Insets.
Initial Installation
QUALIFIED INSTALLERS ONLY
VENT TERMINATION RESTRICTIONS:
N
O
H
D E
L
B
C
B
B
Fixed
Closed
F
Openable
B
G
Fixed
Openable Closed
A
Termination Cap
G
M
J
Air Supply Inlet
G
Gas Meter
K
I
Restriction Zone
A
(Termination not allowed)
Figure 24. Vent Termination Restrictions, refer to Table 4.
Table 4: Vent termination clearances, refer to Figure 24.
Letter
Canadian Installation
A
B
1
2
US Installation
12 in (30 cm)
12 in (30 cm)
Description
Clearance above grade, verandah, porch, deck, or balcony.
9 in (23 cm)
Clearance from window or door that may be opened.
C
12 in (30 cm)*
Clearance from permanently closed window (to prevent
condensation).
D
24 in (60 cm)*
Vertical clearance to ventilated soffit located above the
terminal, within a horizontal distance of 2 ft (60 cm) from
center line of terminal.
E
18 in (45 cm)*
Clearance to unventilated soffit.
F
12 in (30 cm)*
Clearance to outside corner.
12 in (30 cm)*
Clearance to inside corner.
G
H
3 ft (91 cm) within a height of
15 ft (4.5 m) above the meter/
regulator assembly
3 ft (91 cm) within a height of
15 ft (4.5 m) above the meter/
regulator assembly*
Clearance to each side of center line extended above
meter/regulator assembly.
I
3 ft (91 cm)
3 ft (91 cm)*
Radial clearance around service regulator vent outlet.
J
12 in (30 cm)
9 in (23 cm)
Clearance to non-mechanical air supply inlet to building, or
the combustion air inlet to any other appliance.
K
6 ft (1.83 m)
L
7 ft (2.13 m)t
3 ft (91 cm) above if within 10
ft (3 m) horizontally
7 ft (2.13 m)*t
M
+
12 in / 30 cm
+
12 in / 30 cm*
Clearance to mechanical air supply inlet.
Clearance above paved sidewalk or paved driveway located
on public property.
Clearance under verandah, porch, deck, or balcony.
N
12 in (30 cm)*
Clearance horizontally to any surface (such as an exterior
wall) for vertical terminations.
O
12 in (30 cm)
Clearance above roof line for vertical terminations.
1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.
2 In accordance with the current ANSI Z223.1 NFPA 54, National Fuel Gas Code.
* These numbers are only estimates. Clearance in accordance with installation codes and the requirements of the gas supplier.
t
A vent shall not terminate directly above a side walk or paved driveway that is located between two single family dwellings and it serves both dwellings.
+
Permitted only if verandah, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
NOTE: Venting terminals shall not be recessed into walls or siding.
17
Initial Installation
QUALIFIED INSTALLERS ONLY
FIREPLACE HORIZONTAL VENT KIT 50-1235:
Please read and understand these instructions before installing. Failure to follow
these instructions carefully could cause property damage or personal injury.
KIT COMPONENTS:
Qnty
Description
Qnty
Description
1
Horizontal direct vent termination cap
4
Wire spacers
1
Flue collar adapter
1
4 oz tube Mill-Pac Sealant
1
Wall thimble
1
1
5’ (190 cm) length of Ø4” (10 cm) double walled flex pipe
12
4 oz tube RTV silicone
9/16” tech screws
1
5’ (190 cm) length of Ø65⁄8” (16.8 cm) double walled flex pipe
8
11⁄2” wood screws
Please ensure that all components are supplied with this kit. If components are missing or have
been damaged, contact your dealer, distributor, or courier company. Do not attempt the installation if
components are missing or damaged.
INSTALLATION INSTRUCTIONS:
1. Plan your installation and clearances to combustibles. Decide on a location for the unit that will meet
the clearances noted in the venting section, and any or all local code requirements.
2. Set the appliance in the desired location. Determine if any wall studs, electrical wiring, or plumbing
pipes are in the way of the venting system as it passes through the exterior wall. The fireplace location
should be adjusted if obstructions are found in the wall.
3. Project a line from the center point of the flue outlet upward and outward to the desired flue outlet
location on the exterior wall. Using this center point, scribe a 10” (25.4 cm) hole or square on the wall.
Cut the hole from the interior through the exterior wall surfaces.
4. Frame the hole as shown in Figure 29.
5. Trim the wall thimble to match the wall thickness as necessary. Install the wall thimble and secure
it to the inner wall frame using four (4) 11⁄2” wood screws. If a wall is
greater than 8” (203mm) in depth, the clearance above the flex must be
43⁄8” (111mm)
6. Apply a bead of Mill-Pac Black sealant to the new Ø4” (10 cm) by 5” (12.5
cm) provided flue collar adaptor. Press the flue collar into the flue outlet of
the fireplace so that the Mill-Pac seals the flue collar to the flue outlet.
7. Stretch both the Ø4” (10 cm) flex vent and the Ø65⁄8” (16.25 cm) flex intake
liner to the length needed to ensure the flex can be easily connected to the
vent terminal.
����
�������
8. Slide the Ø65⁄8” (16.25 cm) flex intake liner
over the flex vent. Install four (4) wire
spacers around the flex pipe. Ensure the
wire spacers are positioned at either end of
the pipes, and at each end of any elbows in
the liners (refer to Figure 25 and 26).
9. Install the flex pipe assembly through
the wall thimble, ensure that this portion
of pipe slides through the outside wall
far enough to connect onto the vent
Figure 25: Wire Spacers.
termination cap.
Figure 26: Wire Spacer in Place.
18
Initial Installation
QUALIFIED INSTALLERS ONLY
10. Apply a bead of Mill-Pac Black sealant to
the top section of the Ø4” (10 cm) by 5”
Horizontal Vent Termination
(12.5 cm) flue collar adaptor previously
installed into the fireplace flue outlet.
Slide the Ø4” (10 cm) flex vent over
the flue collar and secure with three (3)
sheet metal screws evenly spaced.
11. Place a bead of high temperature
silicone on the intake collar of the
fireplace, slide the Ø65⁄8” (16.25 cm)
Wall Framing
Wall Thimble
flex intake liner over the collar, secure
Fire Stop
the flex liner with three (3) sheet metal
screws evenly spaced.
Exhaust 4" Flex Pipe
12. On the outside of the exterior wall,
apply a bead of Mill-Pac Black sealant
to the Ø4” (10 cm) pipe of the vent
Wire Spacers
terminal. Slide the flex liner onto the
vent terminal and secure with three (3)
sheet metal screws evenly spaced.
Combusion Air 6 5/8" Flex Pipe
13. Place a bead of high temperature
silicone on the intake collar of the vent
terminal, slide the Ø65⁄8” (16.25 cm)
Flue Pipe Adaptor
flex intake liner over the collar, secure
the flex liner with three (3) sheet metal
Figure 27: Installation of Fireplace Horizontal Vent Kit.
screws evenly spaced.
14. Attach the vent terminal to the outside of the house using four (4) wood screws provided.
15. Light the appliance and ensure proper operation.
OTHER APPROVED VENT PARTS:
Table 5: Approved Vent Manufacturers
Manufacturer
Trade Name
Nominal Sizes
American Metal Products
AmeriVent Direct
4” - 6 5/8”
Security Chimneys International LTD
Secure Vent
4” - 6 5/8”
Selkirk Metalbestos
Direct-Temp
4” - 6 5/8”
Simpson Dura-Vent
Direct Vent GS
4” - 6 5/8”
The DV36 fireplace has been tested and certified for use with AMERICAN METAL PRODUCTS “AMERIVENT
DIRECT”, SIMPSON DURAVENT TYPE GS PIPE FOR GAS STOVES. SECURITY CHIMNEY’S “SECURE VENT
DIRECT VENT SYSTEM” and SELKIRK “DIRECT-TEMP VENT SYSTEM” kits are available for horizontal and
vertical venting. When using Simpson Duravent, it is recommended that, before installation, a bead of
RTV High Temperature Silicone should be applied to each outer vent joint, and Mil-Pac to each inner
joint. When planning an installation, it will be necessary to select the proper length of vent pipe for the
particular requirements.
WARNING: Do not mix parts from different vent manufacturers’ systems.
19
Initial Installation
QUALIFIED INSTALLERS ONLY
EXCEPTION TO WARNING: This product has been evaluated by Intertek for using a Direct Vent GS
starting collar in conjunction with Secure Vent, Direct-Temp, and Ameri Vent Direct venting systems. Use
of these systems with the Direct Vent GS starting collar is deemed acceptable and does not affect the
Intertek WH listing of the appliance.
Table 6: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).
Direct Vent GS
Direct-Temp
Secure Vent
908
4DT-6
SV4L6
Ameri Vent Direct
6” pipe length
4D7
7” pipe length
907
4DT-9
9” pipe length
906
4DT-12
SV4L12
4D12
12” pipe length
904
4DT-24
SV4L24
4D2
24” pipe length
903
4DT-36
SV4L36
4D3
36” pipe length
902
4DT-48
SV4L48
4D4
48” pipe length
945
4DT-EL45
SV4EBR45
4D45B
45° elbow, black
990
4DT-EL90
SV4EBR90
4D90B
90° elbow, black
950
4DT-VS
SV4VS
942
4DT-WT
SV4RSN
4DWT
Wall thimble
953
4DT-SC
SV4FC
4DSC
Storm collar
963
4DT-FS
SV4BF
4DFSP
Fire stop
988
4DT-WS/B
SV4BM
4DWS
Wall strap/support/band
970
4DT-HKA
SV0SHK
4DHTK1
Vinyl siding standoff/sheild
911
Horizontal termination kit (SD: Basic Kit,
SEL: Kit A, SC: Standard Kit)
11” to 14 5⁄8” pipe, adjustable
4DT-AJ
4D12A
SV4LA12
4” to 10” pipe , adjustable
11⁄2” to 12” pipe , adjustable
943
4DT-AF6
4DF
Flashing, 0/12 to 6/12 roof pitch
943S
4DT-AF12
4DF12
Flashing, 7/12 to 12/12 roof pitch
943F
20
Description
SV4FA
Flashing, 1/12 to 7/12 roof pitch
SV4FB
Flashing, 8/12 to 12/12 roof pitch
SV4F
Flat flashing
980
4DT-VC
SV4CGV
4DVC
991
4DT-HVC
984
4DT-HC
985
4DT-HHC
978
4DT-VKC
SV0FAK
4DVTK
971
4DT-HKB
SV0SHK2
4DHTK2
Vertical termination
High wind vertical termination
SV4CHC
4DHC
Horizontal square termination
High wind horizontal termination
Vertical termination kit
Horizontal termination kit
(SD: Kit A, SEL: Kit B, SC: Kit)
Initial Installation
QUALIFIED INSTALLERS ONLY
VENTING:
This fireplace has been tested and certified for use with SIMPSON DURAVENT DIRECT VENT TYPE “GS”
PIPE FOR GAS STOVES, SECURITY CHIMNEY’S SECURE VENT DIRECT VENT SYSTEM kits, AMERICAN
METAL PRODUCTS AMERIVENT DIRECT and DIRECT-TEMP SELKIRK METALBESTOS.
A 1” (25 mm) clearance to combustibles must be maintained around any vertical vent pipe. Around a
horizontal vent pipe, the clearance to combustibles should be 2” (51 mm) above and 11⁄2” (38 mm) on the
sides and bottom. When combustible materials are directly above a 90° elbow, 3” (76 mm) of clearance
are necessary (see Figure 28).
Table 7. Vent Pipe Minimum Clearances.
Vertical Pipe to
the Side Walls
Horizontal Pipe to
the Sides & Bottom
Above an Elbow
Above the Unit
Above an Elbow
Not Above the Unit
Above Horizontal
Vent Pipe
Wall Frame 8”
(203mm) or less
Hard
Pipe
1”
(25.4 mm)
11⁄2”
(38.1 mm)
3”
(76.2 mm)
3”
(76.2 mm)
2”
(51 mm)
10”x10”
(25x25cm)
Flex
Pipe
1”
(25.4 mm)
11⁄2”
(38.1 mm)
8”
(203 mm)
4 3⁄8”
(111 mm)
4 3⁄8”
(111 mm)
10”x10”
(25x25cm)
A 10” (254 mm) x 10” (254 mm) frame (see Figure 29) will assure the proper support and spacing for
the vent pipe as it passes through the wall. Installations in Canada require that a wall thimble be used
for passing through walls and ceilings. All sealing and vapour barriers must comply with local building
codes.
When planning an installation, it is necessary to select the proper
length of vent pipe for the particular requirements. The configuration
of the venting pipes depends on the locations of walls, ceilings,
and studs. However, the pipes cannot be of arbitrary length and
arrangement. Because the length of the vertical and horizontal
sections
dramatically
Joists/Studs
affects the burning
efficiency
of
the
fireplace,
certain
Framing
guidelines
have
been set in INITIAL
10”
INSTALLATION - VENT
10”
CONFIGURATIONS
AND
RESTRICTOR SETTINGS.
2" (51mm)
3" (76mm)
41 3/4"
(1048mm)
A two (2) piece wall/
thimble
is
Figure 29. Vent Framing For Wall or Ceiling. ceiling
included with the stove
(see Figure 30).
Venting terminals can
not be recessed into a
wall or siding.
Figure 28. Vent Pipe Clearances.
WARNING: This gas appliance must not be connected
to a chimney flue serving a separate solid-burning
appliances.
Figure 30. Wall/Ceiling Thimble provided.
21
Initial Installation
QUALIFIED INSTALLERS ONLY
VENT CONFIGURATIONS AND RESTRICTOR SETTINGS:
Figures 23 shows the range of venting options, it shows possible vent configurations if the unit is top
vented, for vertical and horizontal terminations, any layout that remains within the shaded area is
acceptable. Having the fewest number of elbows is ideal, as they tend to disrupt air movement. Using
45˚ elbows is preferable to using 90˚ elbows. Also, a shorter vent system will perform better than a
longer one.
The vent restrictor controls the amount of air moving through the vent pipe. Longer vertical vent lengths
necessitate greater restriction; position 1 is open and position 5 is maximum restriction. Figure 31
shows the vent restrictor position required,
NOTE: The total length of the vent pipes can relative to the length of vent pipe. The
not exceed 32 feet (15.12 m). Any combination vent restrictor is located in the center of
32’
of rise and run can be used as long as it lays
(9.75m)
within the shaded area (a total of three (3) 90° the fireplace, above the glass. Figure 32
30’
elbows or six (6) 45° elbows can be used). shows the vent restrictor dial and the holes
(9.14m)
In addition to what is shown, if a 90° that indicate the different levels. To avoid
elbow is used in the horizontal plane,
3 feet (91.4 cm) must be subtracted injury, it is best to make this adjustment
from the allowable horizontal run when the fireplace is cool or use welder’s
(for each 45° elbow, 11⁄2 feet gloves or oven mitts.
25’
must be subtracted from the
allowable horizontal run).
(7.62m)
V
e
n
t
20’
(6.10m)
R
e
s
t
r
i
c
t
o
r
15’
(4.57m)
10’
(3.05m)
P
o
s
i
t
i
o
n
5’
(1.52m)
Note: 0,0 in Figure 31 represents a 90˚
bend directly off the outlet of the unit, 413⁄4
inches (106 cm) from floor, in all horizontal
instances except when using Selkirk and
having less than a 4 feet (1.22 m) rise
and 8 feet (2.44 m) horizontal offset. In
this case, a 1 foot (30.5 cm) rise must be
added below the 90˚ bend.
Note for rear vented: At 293⁄8 inches (75
cm) up, the maximum horizontal rear exit
vent length is 17 inches (43 cm) with a 45°
elbow (see Figure 17).
�
0’
(0m)
41 3/4”
(106cm) from 0’
floor
(0m)
5’
(1.52m)
10’
(3.05m)
� �
�
15’
17’
(4.57m) (5.18m)
Figure 31. Possible Vent Configurations for Top Vented; Vertical
and Horizontal Terminations.
22
�
Figure 32. Possible Vent Restrictor Positions.
Initial Installation
QUALIFIED INSTALLERS ONLY
HORIZONTAL TERMINATION:
NOTES:
1. Horizontal pipes must not be level. For every 12 inches (305 mm) of horizontal travel
(away from the stove), there should be at least 1⁄4 inch (6.4 mm) of vertical travel. Never
allow the vent to run downward, as this could cause high temperatures or even present
the possibility of a fire.
2. The exterior of the horizontal
vent termination must not be
blocked or obstructed.
3. If the vent termination is not
being attached to wood, the
four wood screws provided
should be replaced with
material appropriate fasteners.
4. For buildings with vinyl siding,
a vinyl standoff should be
installed between the vent cap
and the exterior wall. Attach
the vinyl siding standoff to
the horizontal termination.
Note that the termination
bolts onto the flat portion of
the standoff, providing an air
space between the wall and
the vent termination. The air
gap prevents excessive heat
from possibly melting the vinyl
siding.
Wall thimble
fire stop
Horizontal wall
termination
Wall framing
Elbow
5. Horizontal pipes must be
supported every 3 feet (914
mm). Plumber’s all round strap will suffice.
Exhaust
flex pipe
Combustion air
outer pipe
Figure 33. Horizontal Vent Termination
6. When running horizontal pipe, clearances to combustibles must be maintained 11⁄2 inches (38 mm)
sides, 11⁄2 inches (38 mm) bottom, and 2 inches (51 mm) top.
Step 1. Set the fireplace in the desired location. Check to determine if wall studs will be in the way when
the venting system is attached. If this is the case, the location of the fireplace may have to be
adjusted or the venting may have to be offset.
Step 2. Direct vent pipe sections are designed with special twist-lock connections. Dry fit the desired
combination of pipe and elbows to the appliance adaptor.
Step 3. With the pipe in the correct position and attached to the fireplace, mark the wall for a 10 inches
(25.4 cm) x 10 inches (25.4 cm) square hole (see Figure 29). The center of the hole should
match the center line of the horizontal pipe. Cut and frame the hole in the exterior wall where
the vent will be terminated. If the wall being penetrated is made of a non-combustible material
(i.e. masonry or concrete) a 7 inches (17.8 cm) hole is acceptable.
23
Initial Installation
QUALIFIED INSTALLERS ONLY
NOTE: For Simpson Duravent only, place a bead of Mil-Pac or Rutland No 78 Stove and Gasket Cement
on the outer edge of the inner exhaust pipe (non-flared end). Push the pipe sections together, then twist
about 1⁄4 turn, making sure the two sections are fully locked. Wrap all seams with foil ducting tape.
Step 4. With the hole now framed, the wall thimble installed, and the pipe extending into the wall,
proceed to the outside. Attach the termination to the pipe using RTV and Mil-Pac or Rutland No
78 Stove and Gasket Cement to seal joints. The vent pipe must extend into the vent cap at least
11⁄4 inches (3.2 cm). Secure the connection between the vent cap and the pipe by attaching the
two (2) sheet metal straps, which extend from the vent cap assembly to the outer wall of the
vent pipe. Bend any remaining portion of the strap back towards the vent cap. Security Secure
Vent uses a twist lock cap.
Step 5. Position the horizontal vent termination in the center of the 10 inches (25.4 cm) square hole
and attach to the exterior wall with the four screws provided. The arrow on the vent termination
should be pointing up. Run a bead of non-hardening mastic around the edges of the vent
cap, to make a seal with the wall. Ensure the proper clearances to combustibles have been
maintained.
VERTICAL TERMINATION:
Step 1. Check the instructions for required clearances (air spaces) to combustibles when passing
through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces.
Do not pack air spaces with insulation.
Step 2. Set the gas appliance in the desired location. Drop a plumb bob down from the ceiling to
the position of the appliance flue exit, and mark the location where the vent will penetrate
the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole
previously drilled in the ceiling, mark the spot where the vent will penetrate the roof. Determine
if ceiling joists, roof rafters, or other framing will obstruct the venting system. You may wish to
relocate the appliance, or to offset, to avoid cutting load bearing members.
Step 3. To install the Round
Support Box/Wall Thimble
in a flat ceiling, cut a 10
inch (25.4 cm) square hole
in the ceiling, centered in
the hole drilled in Step 2.
Frame the hole as shown
in Figure 29.
Step 4. Assemble the desired
lengths of black pipe
and elbows necessary to
reach from the appliance
adapter up through the
Round
Support
Box.
Insure that all pipe and
elbow connections are
in their fully twist-locked
position.
24
Vertical
Termination
Elbow Strap
Storm Collar
Flashing
Roofing nails
Figure 34. Vertical Vent Termination
Initial Installation
QUALIFIED INSTALLERS ONLY
STEP 5. Cut hole in the roof centered on the small hole placed in the roof from Step 2. The hole should
be of sufficient size to meet minimum requirements for Clearance to Combustibles, as specified.
Continue to assemble lengths of pipe and elbows necessary to reach from the ceiling support
box up through the roof line. Galvanized pipe and elbows may be utilized in the attic, as well
as above the roof line. The galvanized finish is desirable above the roof line, due to the higher
corrosion resistance.
STEP 6. Once the pipe sections have been joined, and run up through the hole in the roof, slip an elbow
strap over the exposed sections, bend the support straps outwards, and push the elbow strap
down to the roof level, as shown in Figure 34. Tighten the clamp around the pipe section. Use
a level to make sure the pipe is truly vertical. With roofing nails, secure the support straps to
the roof. Seal the nails holes heads with non-hardening mastic. Trim the excess length of the
support straps that extend out beyond the edge of the flashing.
STEP 7. Slip the flashing over the pipe section protruding through the roof. Secure the base of the
flashing to the roof with roofing nails. Use a non-hardening sealant between the uphill edge
of the flashing and the roof. Insure the roofing material overlaps the top edge of the flashing.
Verify that you have at least the minimum clearance to combustibles at the roof line.
STEP 8. Continue to add pipe sections until the height of the vent cap meets the minimum code
requirements. Refer to Figure 35 and Table 8. Note that for steep roof pitches, the vent height
must be increased. In high wind conditions, nearby trees, adjoining roof lines, steep pitched
roofs, and other similar factors can result in poor draft, or down drafting. In these cases,
increasing the vent height may solve the problem.
STEP 9. Slip the storm collar over the pipe, and push it down to the top of the roof flashing as shown
in Figure 34. Use the non-hardening sealant around the joint between the pipe and the storm
collar.
STEP 10. Twist-lock the vent cap.
Table 8: Minimum ‘H’ for Figure 35.
Roof Pitch
Dimension ‘H’ obtained
from table below.
H
Figure 35: Height of Vertical Termination;
Reference Table 8.
Minimum Height (H)
Feet
Meters
Flat to 7/8
1
0.3
Over 7/12 to 8/12
1.5
0.46
Over 8/12 to 9/12
2
0.61
Over 9/12 to 10/12
2.5
0.76
Over 10/12 to 11/12
3.25
0.99
Over 11/12 to 12/12
4
1.22
Over 12/12 to 14/12
5
1.52
Over 14/12 to 16/12
6
1.83
Over 16/12 to 18/12
7
2.13
Over 18/12 to 20/12
7.5
2.29
Over 20/12 to 21/12
8
2.44
25
Initial Installation
QUALIFIED INSTALLERS ONLY
NOTES:
(1) If an offset is necessary in the attic to avoid
obstructions, it is important to support the vent
pipe every 3 feet (914 mm), to avoid excessive
stress on the elbows, and possible separation. Wall
straps are available for this purpose (see Figure
36).
plumber’s tape
connected to
wall strap
(2) When ever possible, use 45° degree elbows instead
of 90° degree elbows. The 45° degree elbow offers
less restriction to the flow of flue gases and intake
air.
Wall strap
45° elbows (x2)
(3) For multi story installations; a ceiling firestop is
required at the second floor, and any subsequent
floors (see Figure 29). The opening should be
framed to 10” (254 mm) x 10” (254 mm) inside
dimensions, in the same manner as shown in
Figure 29.
Nails
Figure 36: Use of Wall Straps.
(4) Any occupied areas above the first floor,
including closets and storage spaces,
which the vertical vent passes through,
must be enclosed. The enclosure may be
framed and sheet-rocked with standard
building materials. However consult
the appliance manufactures installation
instructions for the minimum allowable
clearance between the outside of the vent
pipe, and the combustible surfaces of
the enclosure. Do not fill any required air
spaces with insulation.
Ceiling firestop
Ceiling
Use clearances to as
defined by appliance and
vent pipe manufacturers.
Second floor
Figure 37: Multi-Story Vent Pipe Installation.
26
Initial Installation
QUALIFIED INSTALLERS ONLY
INSTALLATION OF ELECTRICAL WIRING FOR THE OPTIONAL FAN KIT:
The electric box/outlet must be hard wired to
the bottom left (or right if the gas line is to
come in on the left) of the unit if you plan to
install the Optional Fan Kit in the future.
Refer to local electrical bylaw for proper
installation. In the absence of local codes,
with the current CSA C22.1 Canadian Electrical
Code Part 1, Safety Standards For Electrical
Installations, or The Current National Electrical
Code ANSI / NFPA 70 in the US.
Figure 38. Install Electrical Outlet Into DV36.
ELECTRICAL SYSTEM FOR THERMOSTAT:
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper operation after servicing.
70 ° F
ON/OFF/Remote
Thermostat Switch
Optional
Remote
Control
Blue
Thermocouple
O
O
N
FF
Thermopile
Purple
Manifold
Pressure Tap
Gas Control
Valve
Grey
70 ° F
UP
DOWN
COOL / HEAT
PROGRAM
Inlet
Pressure
Tap
Optional
Wall Switch
Table 9. Recommended Thermostat
Wire Size.
Wire Size
Max. Length
14 gauge
100 ft (30.48 m)
16 gauge
60 ft (18.29 m)
18 gauge
40 ft (12.00 m)
20 gauge
25 ft (7.62 m)
22 gauge
18 ft (5.49 m)
Pilot Adjustment
Screw
Optional
Thermostat
Figure 39. Wiring Diagram For Gas Valve.
27
Initial Installation
GAS LINE CONNECTION AND TESTING:
WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to
this appliance.
GAS LINE CONNECTION
•
This stove is equipped with a certified flexible pipe located on the right side of the unit terminating in
a 3⁄8” male NPT fitting. Consult your local authorities codes or the CAN/CGA B 149 (1 or 2) installation
code in Canada, or in the USA gas installations follow either local codes or the current edition of the
National Fuel Gas Code ANSI Z223.1.
•
The efficiency rating of this appliance is a product thermal efficiency rating determined under
continuous operating conditions and was determined independently of any installed system.
IN
OUT
L
O
I
O FF
PI L OT
TH
ON
LO
PI T
Always check for gas leaks with a soap
and water solution after completing the
required pressure test.
H
TP
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 1⁄2 psig (3.45 KPa).
�����
�������� ���
��������
�������� ���
TP TH
The appliance and its shutoff valves must be
disconnected from the gas supply piping system
during any pressure testing where the pressure
exceeds 1⁄2 PSIG (3.45 KPa) or damage will occur
to the valve.
����� ����������
�����
������
����
��� �������
����
Figure 40: Fully Labeled Gas Valve.
TO TEST VALVE PRESSURES
The pressure taps are located on the top right of the valve shown in Figure 40.
• Turn set screw 1 turn counter clockwise to loosen,
• Place 5/16” (8 mm) I.D. hose over pressure tap system.
• Check pressures using a manometer.
• When finished, release pressure, remove hose & tighten set screw.
Table 10: Pressure and BTU Information.
Main Orifice
Manifold Pressure
Min. Manifold Pressure
Max Supply Pressure
Min. Supply Pressure
Max BTU/hr Input
Min. BTU/hr Input
Natural Gas
#39 DMS
3.8” W.C. (0.95 KPa)
1.2” W.C. (0.28 KPa)
7.0” W.C. (1.74 KPa)
5.0” W.C. (1.25 KPa)
31,300 BTU/hr (9.17 KW)
17,500 BTU/hr (5.13 KW)
Propane
#53 DMS
11.0” W.C. (2.74 KPa)
2.7” W.C. (0.67 KPa)
13.0” W.C. (3.28 KPa)
12.0” W.C. (2.98 KPa)
28,800 BTU/hr (8.44 KW)
14,900 BTU/hr (4.37 KW)
NEVER USE AN OPEN FLAME FOR LEAK TESTING.
28
Secondary Installation
LOG SET AND EMBER INSTALLATION:
The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched”
and will not burn correctly. The burner (shown in Figure 41), and a few of the logs come with locator pins,
notches and ledges, which make alignment easier. Using the pictures provided, carefully set the logs in
place (see Figures 42 through 47).
NOTE: The logs are fragile and should be handled gently.
Figure 41: This is how the
fire box looks with only the
grate and Optional Brick
Panels in place. The burner
has three (3) locator pins for
the logs.
Figure 41. Empty firebox with grate and locator pins.
Figure 42: The first log to be
placed is the back log. It leans
on the back of the firebox, push
it back as far back as you can.
Locator pins
for left log
Figure 42. First Stage Log Set Installation.
Figure 43: The left log has two
(2) holes in it that will rest over
the two (2) locator pins pointed
out in Figure 42.
Locator pins for
right log
Figure 43. Second Stage Log Set Installation.
29
Secondary Installation
Figure 44: The right log has two
(2) holes in it that will rest over
the two (2) locator pins pointed
out in Figure 43.
Figure 44. Third Stage Log Set Installation.
Figure 45: The front end of the
right/center log has a notch
in it that is to rest around the
right/center post of the grate.
The back end of the log rests on
the burner tray, refer to Figure
44. Ensure the log does not block
any burn ports.
Figure 45. Fourth Stage Log Set Installation.
Figure 46: The bottom of the
left/center log will rest over
the locator pin on the pan burner
and against the grate. The top
half of the log must rest against
the back log, see Figure 43. The
center spot shown in Figure 43 is
a knot in the back log for the left/
center log to rest against. Ensure
the log does not block any burn
ports.
Figure 46. Fifth Stage Log Set Installation.
30
Secondary Installation
Figure 47: Once the logs are in
place the embers can be placed
onto and around the burner to
create a realistic look. Bags
of ceramic fiber embers and
rock wool are provided. The
ceramic fiber comes in chunks
that are about 2 inches (5.1
cm) long. Place them irregularly
around the burner. When there
is a sparse but even layer of
embers, spread the rock wool in
the same manner.
Figure 47. Complete log set-up with embers.
WARNINGS: DO NOT pack this ember material as this could create an unsafe condition. The pieces
should be lightly placed so they don’t block any of the burner ports. DO NOT allow any of the embers to
rest against the pilot assembly.
Caution: Use only the type of ember material supplied with this fireplace. Due to the irregular size of
the ember material, there may be more than required. Use of other foreign materials on the burners may
create dangerous conditions.
Figure 48: The DV36
burning with a good
flame.
NOTE: While the glass
is still removed, it is
recommended that the
gas line be purged by
lighting the pilot.
When
lighting
the
fireplace for the first
time since the log set
and embers have been
installed/replaced, watch
for ignition at ALL the
burner ports. If a long
delay is noticed, turn the
Figure 48. DV36 complete log set-up with embers burning.
appliance off and wait
for it to cool down. Then remove the glass and rearrange the ember material, making sure none of the
burner ports are blocked.
Maintenance: Once a year, the logs should be removed and checked for deterioration or large amounts
of soot. A small amount on the bottom side of the logs is normal. Remove and replace the logs in the
same manner described above.
If new/more embers and rock wool are required, contact your nearest ENVIRO dealer.
Never operate the fireplace with the glass door removed.
31
Secondary Installation
OPTIONAL CERAMIC BRICK PANEL INSTALLATION:
Turn off the gas control knob and allow the
unit to cool.
Baffle
Please ensure that your ceramic panels have not
been damaged.
To Install Panels:
Ledge
Figure 49. Back Panel In Place.
1. Remove the glass door by following the
instruction in the “SECONDARY INSTALLATION GLASS DOOR REMOVAl” section and remove logs
if necessary.
2. Slide center brick panel up behind the baffle
(shown in Figure 49) and rest the bottom of
the panel on the ledge.
3. Using a flat head screwdriver, bend the top tabs on either side at the front of the baffle down (refer to
Figure 51 for placement).
4. Slide the right panel along the side of the firebox until it is tight against the right side of the center
panel. Ensure the panel is behind the top tab (see Figure 50).
5. Bend up the right bottom tab until it touches the bottom of the right panel (see Figure 52) and press
the top right tab tight against the top of the panel (see
Figure 51).
6. Repeat steps 4 and 5 for the left panel.
7. Install the log set (refer to SECONDARY INSTALLATION - LOG SET
AND EMBER INSTALLATION) and glass door.
To Remove Panels:
1. Pull the bottom and top tabs away from the side panels.
2. Carefully slide the side panels out towards the front, do not
slide the panels on the tabs.
3. Push the center panel straight up about 1⁄4 inch (5 mm),
pull the bottom out past the ledge, then pull the panel down
until it is past the bottom of the baffle. Remove panel from
firebox
Figure 51. Top Tab For Right Panel.
32
Figure 50. Right Panel In Place.
Figure 52. Bottom Tab For Right Panel.
Secondary Installation
QUALIFIED INSTALLERS ONLY
OPTIONAL FAN KIT INSTALLATION:
The optional fan is thermostatically controlled and it will not operate if the appliance is cold. A few
minutes after the appliance is lit and the variable speed control is set at a desired setting, the fan will
automatically turn on. The fan will automatically turn off a few minutes after the appliance is shut off.
Fan Control
Black
120oF (49oC)
Temperature Sensor
White
White
Black
Black
Green
Electrical Cord
White
Black
White
Black
Green
Green/Yellow
Fan
Electrical
Power Cord
Black
The fireplace must be electrically
connected and grounded in accordance
with local codes or, in the absence of
local codes, with the current CSA C22.1
Canadian Electrical Code Part 1, Safety
Standards For Electrical Installations, or
The National Electrical Code ANSI / NFPA
70 in the US.
WARNING: The electrical grounding
instructions must be followed. The
fan kit is equipped with a three-prong
(grounding) plug for your protection
against shock hazard, and should be
plugged directly into a properly grounded
three-prong outlet. DO NOT cut or remove
the grounding prong from this plug.
CAUTION: When servicing controls, label
all wires prior to disconnection. Wiring
errors can cause improper and dangerous
operation. Verify proper operation after
servicing.
Figure 53. Wiring Diagram For Fan Control.
Kit Contents:
This kit includes a fan assembly (a fan within a box
housing connected by a wire to the fan control box
then ends at a three prong plug) and two (2) T-20
torx screws.
Please ensure that your fan kit has not been
damaged. If so, contact your dealer, distributor, or
courier company before starting this installation.
Figure 54. Placing Fan Kit Into DV36
33
Secondary Installation
Slots to go
over grommets
Grommets
Figure 55. Hook Fan Tabs Over Grommets at Unit Back.
Installation of Kit:
1. Ensure the appliance is turned off and cool.
2. Remove the bottom louvers.
3. Place fan in lower area of unit behind the controls (see Figure 54).
4. Hook the two (2) slots on the fan box over the two (2) grommets on the back wall, refer to Figure
55.
5. Using two (2) T-20 screws, attach the fan control box to the ignitor control panel, refer to Figure 56.
Before tightening the screws ensure that the thermal switch on top of the box firmly contacts the
firebox bottom.
6. Plug the fan into the hard wired electrical box/outlet (refer to Figure 57) that was installed in the
“INITIAL INSTALLATION - INSTALLATION OF ELECTRICAL OUTLET FOR OPTIONAL FAN KIt“.
Figure 56. Install Fan Control Box.
34
Figure 57. Plug In Fan Kit.
Trouble Shooting
Problem
Possible Cause
The main burner does not The gas valve may not be on.
ignite when called for.
Thermostat is not calling for
heat.
Solution
• Check that the gas control knob is in the “ON” position.
• Adjust the thermostat several degrees above ambient
temperature.
Problem with gas valve.
• Use a DC voltmeter to measure the voltage across the
TPTH and TP terminals. Main operator voltage: Open
circuit ≥ 325mV Closed circuit ≥ 100mV
• If voltage is not present, check the control circuit for
proper operation.
• If proper control system voltage is present, replace the
gas control.
Defective piezo ignitor.
• Check connections to ignitor.
• If ignitor connections are good but no spark, replace
ignitor.
Broken spark electrode.
• Check for broken ceramic insulation, replace electrode if
broken.
Misaligned spark electrode.
• If spark is not arcing from electrode to pilot, loosen the
screws on the pilot base adjust and tighten.
Problem with thermocouple
circuit.
• Check for proper connection of the thermocouple to the
rear of the valve. If loose, fully tighten.
• Check pilot for full flame impingement around
thermocouple. If flame is too small, check gas pressure,
adjust pilot rate screw, check pilot head for damage.
• Check thermocouple voltage at valve. It must be greater
than 5 mV. If low, replace thermocouple.
Air in gas line (pilot dies while
knob is depressed).
• Bleed line.
• Check gas line pressure.
• Contact dealer.
Burners will not remain lit.
Problem with thermopile
circuit.
• Check gas line pressure .
• Check for flame impingement on thermopile. If low, see
“Pilot will not remain lit”.
• Check thermopile for minimum of 300 mV when burner is
switched on.
• Check wiring to thermostat for breaks.
Flame lifting
Leak in vent pipe
• Check for leaks in vent connections.
Improper vent configuration
• Check vent configuration with manual.
Terminal may be recirculating
flue gases
• Check to see if terminal is on correctly.
• May need to install high wind termination cap.
• Contact dealer.
Spark will not light the pilot
after repeatedly pressing the
spark ignitor.
Pilot will not remain lit.
Glass fogs up
Normal Condition: after the appliance warms up the glass will clear.
**Due to additives in gas, glass may get hazy during operation** Clean as needed.
Blue Flames
Normal during start up: flames will yellow as the fireplace heats up.
Flames are burning “dirty” or
sooting
Flame impingement
• Check log positioning.
• Increase primary air by opening the venturi shutter and/
or by opening the vent restrictor.
See also “Burners will not remain lit.”
Remote control doesn’t work
Problem with the remote
• One or more of the batteries are dead. See remote
control instructions.
Problem with fireplace
• The on/off switch is turned to OFF.
• The gas control valve is turned to PILOT or OFF.
• The pilot has gone out.
35
Parts List
Reference
Number
1
2
2
2
2
2
2
3
4
5
6
7
7
8
9
10
11
12
13
14
15
16
36
Part Description
Part Number
120°F Ceramic Fan Temperature Sensor
Thermocouple
Spark Electrode with Ignitor Cable
Thermopile
Pilot Orifice NG Threaded
Pilot Orifice LP Threaded
Pilot Gasket
S.I.T. Piezo Ignitor
Fan Controller - 115V
Convection Blower - 115V
SIT Pilot 1⁄8” Tube with End Furrels (1 piece)
Enviro Logo Gel Decal
Blank Orifice #73
Embers
On/Off Remote Control Kit
EC-001
EC-009
EC-011
EC-012
EC-019
EC-020
EC-021
EC-023
EC-039
EC-069
30-043
50-322
50-343
50-491
50-559
Programmable Wall Mounted Remote Control
50-583
Dual Bulb Door Gasket (10 feet)
Door, Glass, & Gasket
Door Latch Mechanism with Spring (set of 2)
Pan Burner with Right & Left Firebox Cover
Burner Tray Complete
Grate
Log Set with Embers
Wall Switch Kit
Three Flame Pilot Hood
DV36 Owner’s Manual
S.I.T. Nova Valve Convertible
Conversion Kit from LP to NG Convertible
Conversion Kit from NG to LP Convertible
S.I.T. Valve Conversion Screw with O-ring
S.I.T. Valve Conversion Screw Cap
50-634
50-911
50-912
50-913
50-915
50-916
50-917
50-920
50-925
50-927
50-1421
50-1424
50-1425
50-1450
50-1451
Parts List - Options
Reference
Number
17
18
18
18
19
20
Part Description
Brick Panels (set of 3)
Louvre Set - Brushed Antique Copper (set of 2)
Louvre Set - Brushed Nickel (set of 2)
Louvre Set - Gold (set of 2)
Fan Kit
Louvre Set - Black (set of 5 with mounting brackets)
Cape Cod Fascia
Vine Insets - Painted
Vine Insets - Brushed Gold
Vine Insets - Brushed Nickel
Frost Insets - Painted
Frost Insets - Brushed Gold
Frost Insets - Brushed Nickel
Part Number
50-926
50-951
50-952
50-953
50-954
50-956
50-1189
50-1190
50-1191
50-1192
50-1193
50-1194
50-1195
37
�
��
38
�
�
��
�
�
��
��
��
��
��
�
�
�
��
��
�
��
��
Parts Diagram
Warranty
Sherwood Industries Ltd. offers a Limited Lifetime Warranty on this gas product. This Limited Lifetime
Warranty covers the appliance for a period of seven years from the date of installation. This warranty
applies only to the original owner in the original location.
Covered under the lifetime warranty are the chassis and the heat exchanger. These steel components
are covered against manufacturer’s defects for seven years and the labour for the first year. The following
exclusions apply: over-firing due to incorrect setup or tampering, damage caused by incorrect installation,
usage or abuse. The unit must be properly installed by a qualified technician or installer, and must meet
all local and national gas and building code requirements.
Under the Limited Lifetime Warranty, the following components are also covered: log set, burners and
glass. The following exclusions apply:
Plated Finish: Damage caused by scratching, marring, chemicals, fingerprints, abrasive cleaners or
discoloration with age. Items with Antique Copper that have had a green discoloration of the finish.
If discoloration occurs, please follow the cleaning instructions as outlined in the “Maintenance And
Service” section.
Glass: Damage caused by the use of harsh or abrasive cleaners, striking the glass, surface
contaminants
Log Set: Damage caused by incorrect handling or misuse
Burners: Damage caused by improper or continuous operation under incorrect conditions
Sherwood Industries Ltd. offers a two-year warranty against manufacturing defects on all the electrical
components and gas components, paint is also covered against flaking. This offer includes parts and
labour for one year, and parts only thereafter.
Your dealer shall make all claims under this warranty in writing. When filing a warranty claim please
complete the following information on an official warranty claim form:
TO THE DEALER:
Name, address and telephone number of purchaser and date of purchase, date of installation, name of
installer and dealer, nature of complaint, defects or malfunction, description and part number of any parts
replaced.
TO THE DISTRIBUTOR:
Sign and verify that work and information are correct.
This warranty covers defects in materials and workmanship only if the product has been installed according
to the manual’s instructions. If the product is damaged or broken as a result of misuse or mishandling,
the warranty does not apply. The warranty does not cover removal and reinstallation costs.
Sherwood Industries Ltd. reserves the right to repair or replace the defective product. The shipping costs
are to be paid by the consumer. All warranties by the manufacturer are set forth and no claim shall be
made against the manufacturer on any oral warranty or representation.
Sherwood Industries Ltd. and its employees or representatives will not assume any damages, either
directly or indirectly, caused by improper usage, operation installation, servicing or maintenance of this
appliance.
Sherwood Industries Ltd. reserves the right to make changes without notice. Please complete and mail
the warranty registration card and have the installer fill in the installation data sheet in the back of the
manual for warranty and future reference.
39
Installation Data Sheet
The following information must be recorded by the installer for warranty purposes and future reference.
NAME OF OWNER:
NAME OF DEALER:
_________________________________________
_________________________________________
ADDRESS:
ADDRESS:
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
PHONE:___________________________________
PHONE:___________________________________
MODEL:___________________________________
NAME OF INSTALLER:
SERIAL NUMBER:___________________________
DATE OF PURCHASE: _____________
DATE OF INSTALLATION:___________(dd/mm/yyyy)
� NATURAL GAS (NAT)
_________________________________________
(dd/mm/yyyy)
� PROPANE(LPG)
ADDRESS:
_________________________________________
_________________________________________
_________________________________________
INLET GAS PRESSURE:_________in wc
PHONE:___________________________________
MAIN BURNER ORIFICE:__________# DMS
PILOT ORIFICE #_________OR________in diam.
INSTALLER’S SIGNATURE:
_________________________________________
MANUFACTURED BY:
SHERWOOD INDUSTRIES LTD.
6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3
www.envirofire.biz
March 20, 2006
C-11033
40
Download PDF

advertising