Specifications | Agilent Technologies 1680 Yard Vacuum User Manual

1680-Series Logic Analyzers
Quick Start/Installation
Product Overview 2
First-Time Power Up Considerations 4
Answering Windows Welcome Questions 6
Additional First-Time Setup Steps 8
Making a Measurement 9
Snap to Edge Markers 11
Left-Click Menus 12
Tree Structure Labels 12
Offline Analysis 13
Marker Overview 13
Tool Tips 13
Trigger History 14
Probing 15
Changing Network Settings 15
Changing Windows Firewall Settings 16
Software Installation and Upgrades 20
Proper Cooling 21
Self-Test 22
Emergency Recovery 22
Specifications and Characteristics 23
Safety Notices 25
Agilent Technologies
Product Overview
Front Panel
Refer to the online help in the logic analyzer for information on using the
analyzer.
Floppy Drive
File Keys
RUN/STOP
Keys
Scroll Knob
Shortcut
Keys
Keypad
Horizontal,
Vertical, and
Marker Controls
1 MHz TTL
Ground
Rear Panel
Before you turn on the system, connect your mouse and keyboard to the
1680-series logic analyzer rear panel. A connected mouse and keyboard are
required for normal system use. The following rear panel figure is
representative. Yours may look different.
2
1680-Series Quick Start/Installation
Printer
Mouse
Audio IN
Audio OUT
Keyboard
Mic IN
USB Ports
Accessories Pouch
Snap the accessories pouch to the top of the 1680-series logic analyzer. Use it
to store probe leads, accessories, or manuals. Use the tie-down straps under
the flap to conveniently hold pod cables not in use or during transport.
Accessories Pouch (top flap)
Pod Cables
Tie-down Straps
Snaps (4)
1680-Series Quick Start/Installation
3
First-Time Power Up Considerations
The first time you turn on the logic analyzer, the Windows® Welcome session
starts. Your logic analyzer configuration and the answers to the Windows
Welcome questions are affected by how you choose to use the logic analyzer.
NOTE
Use the Enter and arrow keys on the attached keyboard. The logic analyzer front-panel keys
do not work until Windows is running.
Determine Whether the Instrument will be Connected to the Network
NOTE
If you plan to use COM automation to programmatically control a logic analyzer from a
remote computer, be aware that the remote computer and the logic analyzer must both
have the same kind of network membership; that is, they must both be members of a
"Workgroup", or they must both be members of a "Domain". This is due to the security
requirements of Distributed COM.
Standalone
You are going to use the logic analyzer as a standalone instrument (no LAN
connection). Printing requires a printer attached to the logic analyzer, sharing
files is done via USB flash drive or floppy disk.
Connected to a Network
If you require the ability to print, share files, remotely control the logic
analyzer, etc. over the network, you need to either join a workgroup or
domain.
Get Network Setup Information
For networking, find out whether the network that your instrument will be
connected to uses the Microsoft Workgroup model or Microsoft Domain model.
In order for your instrument to perform tasks over the network (print,
transfer files, etc.) your instrument must be configured appropriately for the
networking model in use at your site.
4
1680-Series Quick Start/Installation
Information you may require to complete your network configuration may
include, but is not limited to,
• The Workgroup or Domain name.
• Methodology for assigning IP addresses at your site (for example, DHCP).
• Domain Name Service (DNS).
Other network information that may be readily available from your network
administrator.
1680-Series Quick Start/Installation
5
Answering Windows Welcome Questions
Once you have determined how you want to use your logic analyzer and your
network configuration, power up your logic analyzer and answer the Windows
Welcome questions.
Table 1
Answering Windows Welcome Questions
Standalone (No LAN)
Workgroup
Domain
Help protect your PC
N/A
What's your computer's name?
(After answering, wait several
minutes for next question to
appear)
If your organization has a standard naming scheme, use that scheme. Otherwise,
choose a descriptive name that follows the suggestions on the screen (less than 15
characters, etc.)
What's your administrator
password?
Agilent recommends entering an administrator password for administrator accounts.
See page 8 for actions that require administrator accounts.
Is this computer in a domain?
No
(Is given WORKGROUP
membership)
No
(Is given WORKGROUP
membership)
Yes
Enter the domain name the
logic analyzer will log onto.
Enter your domain settings.
N/A
N/A
Enter the name/password of
a user who can add the logic
analyzer to the domain.
Checking your Internet
connectivity
Press 'Skip'
Wait for this to finish.
Wait for this to finish.
How will this computer connect
to the Internet?
N/A
N/A
Choose the appropriate
answer.
Setting up a high-speed
connection?
N/A
N/A
Enter either the fixed IP/DNS
assigned by your network
administrator or select
"Obtain Automatically".
6
Choose “Help protect my
PC by turning on
Automatic Updates
now”.
Choose “Help protect my PC
by turning on Automatic
Updates now”.
1680-Series Quick Start/Installation
Table 1
Answering Windows Welcome Questions
Standalone (No LAN)
Workgroup
Domain
(If LAN connected) Will this
computer connect to the
Internet directly, or through a
network?
N/A
Choose "Yes, through a
network"
(Agilent does not
support connecting to
the internet through a
modem directly
connected to the logic
analyzer.)
N/A
(If LAN is not connected)
Windows unable to determine
LAN connectivity.
N/A
You are told to set up
LAN later.
N/A
Ready to register with Microsoft
Windows XP is already enabled to run on the logic analyzer. This registration is to
allow Microsoft to contact you.
Who will use this computer?
For All: Entering names here lets multiple users use the logic analyzer with
administrator permissions. By default their passwords will be blank.
If expected Windows Welcome questions do not appear
During first-time power-up, depending on the configuration of your network,
some of the Windows Welcome questions that should appear, like “Is this
computer in a domain?”, may not appear.
If this occurs, you need to change the logic analyzer’s network setup (after the
first-time power up) using the normal Windows XP methods (see “Changing
Network Settings" on page 15).
1680-Series Quick Start/Installation
7
Additional First-Time Setup Steps
Establishing an Administrator Account
(recommended for standalone and networked instruments)
Agilent recommends that you set up an Administrator account for your logic
analyzer. You have to be logged in to the Administrator account to do the
following:
• Install most software (applies whether the instrument is networked or
standalone).
• Change the workgroup.
• Perform "Windows Updates".
• Change firewall settings.
Protecting the Instrument’s Operating System
Microsoft recommends the following three steps to ensure the instrument's PC
is protected.
1 Use an internet firewall.
2 Get operating system updates.
3 Use up-to-date antivirus software.
8
1680-Series Quick Start/Installation
Making a Measurement
1 Start up the logic analyzer, connect to your target system, and select
Setup>Bus/Signal.
2 Assign buses and signals and click OK.
1680-Series Quick Start/Installation
9
3 Enter a trigger value.
4 Acquire and view data.
10
1680-Series Quick Start/Installation
Snap to Edge Markers
You can set the markers to jump to the nearest edge of a waveform. A yellow
target will show which edge the marker will jump to.
1680-Series Quick Start/Installation
11
Left-Click Menus
Drag a box around parts of the data. When you release the mouse button, a
menu appears.
Tree Structure Labels
Show individual signals in buses by clicking on the + to expand.
12
1680-Series Quick Start/Installation
Offline Analysis
Install the Agilent Logic Analyzer application on another Windows XP or
Windows 2000 computer and you can analyze data without the 1680-series
logic analyzer.
1 Follow the instructions in “Software Installation and Upgrades" on page 20
to load the 1680-series logic analyzer software on your PC.
2 Acquire a trace with the logic analyzer.
3 Save a configuration file with data.
4 Copy the file to the PC being used for offline analysis.
5 From the Agilent Logic Analyzer application software on your PC, open the
configuration file.
Marker Overview
The marker overview display shows marker locations within the data and the
part of data currently being displayed.
Tool Tips
Pause the cursor over a tool Icon and a ‘Tool Tip Window” will appear.
1680-Series Quick Start/Installation
13
Trigger History
Save and recall trigger settings.
14
1680-Series Quick Start/Installation
Probing
Probing is the key to effective and efficient use of logic analyzers. Agilent
Technologies offers a wide variety of probing accessories that support
general-purpose and application-specific measurement needs. We provide
reliable, electrically and mechanically unobtrusive probes that make it easy to
connect your Agilent logic analyzer to your system under test. For more
information on Agilent probes:
• See the quick reference card that came with your logic analyzer for an
overview of probing solutions.
• Go to www.agilent.com/find/logic_analyzer_probes for the most up-to-date
information on probe compatibility with a given logic analyzer and
purchasing information.
• Go to www.agilent.com and search for Probing Solutions for Logic
Analyzers (publication 5968-4632E) for a catalog of detailed probing
information.
To connect and set up a probe, follow the instructions in the User’s Guide that
came with the probe.
Changing Network Settings
To make network changes after the first-time power up:
• To change from a workgroup to a domain or vice versa, click Start then
right click on My Computer and select Properties. Select the Computer
Name tab and click Change.
• To change network connection properties, click Start>Control
Panel>Network Connections. Select the connection you want to change
and click Change settings of this connection.
For more information on changing network settings, refer to the Windows XP
online help.
1680-Series Quick Start/Installation
15
Changing Windows Firewall Settings
When 1680-series logic analyzers are shipped from the factory, the Windows
Firewall is enabled and set up with the exceptions required by the logic
analyzer.
To give other applications/ports access through the firewall
For example, you may need to change firewall settings in order to:
• Use NetOp to remotely control the logic analyzer.
• Use RealVNC to remotely control the logic analyzer.
To change firewall settings to give other applications/ports access:
1 From the Windows Start menu, choose Start>Control Panel.
2 In the Control Panel window, open Windows Firewall.
16
1680-Series Quick Start/Installation
3 In the Windows Firewall dialog, click the Exceptions tab.
4 In the Exceptions tab, if the program or service is listed, check its box to
enable it; otherwise, click Add Program... to give unlisted applications
permission to penetrate the firewall, or click Add Port... to give unlisted
ports access through the firewall.
Refer to the application’s documentation for information on port numbers
or other firewall setup information.
NOTE
Note that there are separate Windows Firewall profiles: Domain for when the computer has
domain membership, and Standard for when the computer has workgroup membership. If
you change the type of membership, any changes you made to the Windows Firewall
settings will have to be made again.
1680-Series Quick Start/Installation
17
To restore the logic analyzer firewall defaults
1 From the Windows Start menu, choose Start>Control Panel.
2 In the Control Panel window, open Windows Firewall.
18
1680-Series Quick Start/Installation
3 In the Windows Firewall dialog, click the Advanced tab.
4 In the Advanced tab, click Restore Defaults to restore the default Windows
Firewall settings.
5 In the confirmation dialog, Click Yes.
6 Click OK to close the Windows Firewall dialog.
7 From the Windows Start menu, choose Start>Run; then, enter or select the
file “C:\Program Files\Agilent Technologies\Logic Analyzer\
agFirewSP2.wsf”, and click OK.
The logic analyzer firewall defaults enable the following exceptions:
• Agilent Logic Analysis Application program.
• Agilent Logic Analysis Service program.
• File and Printer Sharing.
• Microsoft RPC Endport Mapper TCP port.
• Remote Desktop service.
• Web Server (HTTP) port.
1680-Series Quick Start/Installation
19
The logic analyzer firewall defaults also enable the following ICMP (Internet
Control Message Protocol) settings:
• Allow incoming echo request.
• Allow outgoing destination unreachable.
• Allow outgoing time exceeded.
NOTE
Note that there are separate Windows Firewall profiles: Domain for when the computer has
domain membership, and Standard for when the computer has workgroup membership.
When you restore the logic analyzer firewall defaults, the defaults for both profiles are
restored.
Software Installation and Upgrades
Agilent Logic Analyzer Software
The Agilent 1680-series logic analyzers are shipped with software already
installed, including any licensed optional products that you may have
purchased. The licensing process (described below) has been performed and
the (*.lic) license file is in place.
To upgrade the logic analyzer software, insert a product CD and click
INSTALL PRODUCTS>Install Logic Analyzer. Note that newer versions of
the Agilent Logic Analyzer software will automatically uninstall the previous
version as a step in the upgrade. (User files in the "Documents and Settings"
tree are not affected.)
To install the logic analyzer software onto your PC for offline processing,
insert the product CD into your PC drive, click INSTALL PRODUCTS>"Install
Logic Analyzer.
Logic analyzer product software can be downloaded from the web at:
http://www.agilent.com/find/16900_SW_Download
Logic analyzer product CDs can be ordered from this web-site:
http://software.cos.agilent.com/LogicAnalyzerSW
To be notified when software upgrades are available for downloading from the
web, please sign up for e-mail notifications at:
http://www.agilent.com/find/emailupdates
20
1680-Series Quick Start/Installation
Optional Products
If applicable, follow the instructions on the entitlement certificate that came
with your purchase to enable the optional tool.
Proper Cooling
Allow at least 5 cm (2 inches) of space between instruments for proper
cooling.
5 cm (2 inches)
1680-Series Quick Start/Installation
5 cm (2 inches)
21
Self-Test
To run self-tests go to Help>Self Test and then select the desired test.
Emergency Recovery
Follow the instructions provided with the recovery CD to restore your system
software. This will only restore factory program files. User files and other
programs will then need to be restored from your backup files.
22
1680-Series Quick Start/Installation
Specifications and Characteristics
The following electrical and operating characteristics are not specifications,
but are typical operating characteristics for the Agilent 1680-series logic
analyzers.
Electrical Characteristics
Power
Requirements
Frame:: 115/230 Vac +/- 20%, 48-66Hz, 610W Max
CAT II (Line voltage in appliance and to wall outlet)
Pollution degree 2
Environmental Characteristics (Operating)
Temperature
Instrument: 0° to + 50° C (+32° to +122° F)
Disk Media: 10° to + 40° C (+50° to +104° F)
Probes/cables: 0° to + 65° C (+32° to +149° F)
Altitude
3,000 m (10,000 ft)
Humidity
Relative humidity 8 to 80% at 40° C (104° F). Avoid sudden, extreme
temperature changes which could cause condensation on the circuit
board.
For indoor use only.
More specifications and characteristics for your instrument and measurement
modules are in the on-line help. To find them go to:
1680-Series Quick Start/Installation
23
1 Click Help>Help Topics.
2 Click Reference>Specifications and Characteristics.
24
1680-Series Quick Start/Installation
Safety Notices
This apparatus has been designed and tested in accordance with IEC
Publication 1010, Safety Requirements for Measuring Apparatus, and has been
supplied in a safe condition. This is a Safety Class I instrument (provided with
terminal for protective earthing). Before applying power, verify that the
correct safety precautions are taken (see the following warnings). In addition,
note the external markings on the instrument that are described under "Safety
Symbols."
Warnings
• Before turning on the instrument, you must connect the protective earth
terminal of the instrument to the protective conductor of the (mains) power
cord. The mains plug shall only be inserted in a socket outlet provided with
a protective earth contact. You must not negate the protective action by
using an extension cord (power cable) without a protective conductor
(grounding). Grounding one conductor of a two-conductor outlet is not
sufficient protection.
• Only fuses with the required rated current, voltage, and specified type
(normal blow, time delay, etc.) should be used. Do not use repaired fuses or
short-circuited fuse holders. To do so could cause a shock or fire hazard.
• If you energize this instrument by an auto transformer (for voltage
reduction or mains isolation), the common terminal must be connected to
the earth terminal of the power source.
• Whenever it is likely that the ground protection is impaired, you must make
the instrument inoperative and secure it against any unintended operation.
• Service instructions are for trained service personnel. To avoid dangerous
electric shock, do not perform any service unless qualified to do so. Do not
attempt internal service or adjustment unless another person, capable of
rendering first aid and resuscitation, is present.
• Do not install substitute parts or perform any unauthorized modification to
the instrument.
• Capacitors inside the instrument may retain a charge even if the
instrument is disconnected from its source of supply.
1680-Series Quick Start/Installation
25
• Do not operate the instrument in the presence of flammable gasses or
fumes. Operation of any electrical instrument in such an environment
constitutes a definite safety hazard.
• Do not use the instrument in a manner not specified by the manufacturer.
• To optimize your comfort and productivity, it is important that you set up
your work area correctly and use your equipment properly. Refer to
http://www.agilent.com/quality/Working_In_Comfort.pdf for set-up and
use recommendations
• Position equipment so that it is not difficult to disconnect the power cord.
To clean the instrument
If the instrument requires cleaning:
1 Remove power from the instrument.
2 Clean the external surfaces of the instrument with a soft cloth dampened
with a mixture of mild detergent and water.
3 Make sure that the instrument is completely dry before reconnecting it to a
power source.
Safety Symbols
!
Instruction manual symbol: the product is marked with this symbol when it is
necessary for you to refer to the instruction manual in order to protect against
damage to the product.
Hazardous voltage symbol.
Earth terminal symbol: Used to indicate a circuit common connected to
grounded chassis.
26
1680-Series Quick Start/Installation
1680-Series Quick Start/Installation
27
www.agilent.com
© Agilent Technologies, Inc. 2004
Printed in Malaysia October 2004
*01680-97012*
Manual part number 01680-97012
Agilent Technologies
Download PDF

advertising