Agilent Technologies 5373A Network Hardware User Manual

EarthlingBIOS.fm Page 1 Thursday, April 11, 2002 9:48 AM
Fujitsu LifeBook
C Series
BIOS Guide
LifeBook C Series Model:
C2110
Document Date: 04/05/02
Document Part Number: FPC58-0668-01
F U J I T S U P C C O R P O R AT I O N
EarthlingBIOS.fm Page 2 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
C Series BIOS
PO INTS
BIOS SETUP UTILITY
n
The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your
BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the
BIOS environment to operate your notebook.
n
The BIOS Setup Utility configures:
Device control feature parameters, such as changing
I/O addresses and boot devices.
System Data Security feature parameters, such
as passwords.
n
n
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your notebook.
2. Press the [F2] key once the Fujitsu logo appears
on the screen. This will open the main menu
of the BIOS Setup Utility with the current
settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key
to scroll through the other setup menus to review or
alter the current settings.
Navigating Through The Setup Utility
The BIOS setup utility consists of seven menus: Main,
Advanced, Security, Boot, Info, and Exit. This document
explains each menu in turn, including all submenus and
setup items.
The following procedures allow you to navigate the
setup utility menus:
1. To select a menu, use the cursor keys:
2. To select a field within a menu or a submenu, use the
3.
4.
5.
6.
2
cursor keys:
To select the different values for each field, press the
[Spacebar] or [+] to change to the next higher selection and [F5] or [-] to go to the next lower selection.
To activate a submenu press the [Enter] key.
To return to a menu from a submenu, press
the [Esc] key.
To go to the Exit menu from any other menu,
press the [Esc] key.
Selecting a field causes a help message about that
field to be displayed on the right-hand side of the
screen.
Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will
cause a list of all options for that item to be
displayed. Pressing the Enter key again will select
the highlighted choice.
7. Pressing the [F9] key resets all items in the BIOS to
the default values.
8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
9. Pressing the [F1] key gives you a general help screen.
Entering the Setup Utility After a Configuration
Change or System Failure
If there has been a change in the system configuration
that does not match the parameter settings stored in
your BIOS memory, or there is a failure in the system,
the system beeps and/or displays an error message after
the Power On Self Test (POST). If the failure is not too
severe, it will give you the opportunity to modify the
settings of the setup utility, as described in the following
steps:
1. When you turn on or restart the computer there is a
beep and/or the following message appears on the
screen:
Error message - please run SETUP
program Press <F1> key to continue,
<F2> to run SETUP
2. If an error message is displayed on the screen, and
you want to continue with the boot process and start
the operating system anyway, press the [F1] key.
PO INTS
n
If your notebook emits a series of beeps that sounds
like a code and the display is blank, please refer to the
Troubleshooting Section. The Troubleshooting Section
includes a list of error messages and their meanings.
n
If your data security settings require it, you may be
asked for a password before the operating system will
be loaded.
EarthlingBIOS.fm Page 3 Thursday, April 11, 2002 9:48 AM
C Series BIOS
3. If an error message is displayed on the screen, and
you want to enter the setup utility, press the [F2] key.
4. When the setup utility starts with a fault present, the
system displays the following message:
Warning!
Error message
[Continue]
5. Press any key to enter the setup utility. The system
will then display the Main Menu with current
parameters values.
3
EarthlingBIOS.fm Page 4 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
MAIN MENU – SETTING STANDARD SYSTEM PARAMETERS
The Main Menu allows you to set or view the current
system parameters. Follow the instructions for Navigating Through The Setup Utility to make any changes.
(See Navigating Through The Setup Utility on page 2 for
more information.)
The following tables show the names of the menu fields
for the Main menu and its submenus, all of the options
for each field, the default settings and a description of
Main
the field’s function and any special information needed
to help understand the field’s use.
*Note that actual drive labels shown may vary.
POINT
System Time and System Date can also be set from your
operating system without using the setup utility. Use
the calendar and time icon on your Windows Control
panel or type time or date from the MS-DOS prompt.
PhoenixBIOS Setup Utility
Security
Power
Boot
Advanced
Info
Exit
Item Specific Help
▲ ▲
System Time:
System Date:
[02:34:56]
[04/03/2002]
Floppy Disk A:
[1.44/1.2 MB, 3.5"]
Primary Master
Secondary Master
[TOSHIBA MK2018GAP-(PM)]
[TOSHIBA DVD-ROM-SD-R2102-(SM)]
Language:
[English (US)]
Select Item
Select Menu
<Tab>, <Shift-Tab>, or
<Enter> selects field.
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
Adjust calendar clock.
F9 Setup Defaults
F10 Save and Exit
Figure 1. Main Menu
Table 1: Fields, Options and Defaults for the Main Menu
Note that the parameters listed below may differ, as determined by your system configuration.
Menu
Field
4
Options
Default
Description
System
Time:
–—
–—
Sets and displays the current time. Time is in a 24 hour format of
hours:minutes:seconds with 2 digits for each. (HH:MM:SS). Example: 16:45:57.
You may change each segment of the time separately. Move between the
segments with the [Tab] key and/or [Shift] + [Tab] keys.
System
Date:
–—
–—
Sets and displays the current date. Date is in a month/day/year numeric format
with 2 digits each for month and day and 4 digits for year. (MM/DD/YYYY) for
example: 10/16/2001. You may change each segment of the date separately.
Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys.
EarthlingBIOS.fm Page 5 Thursday, April 11, 2002 9:48 AM
Main Menu
Table 1: Fields, Options and Defaults for the Main Menu
Note that the parameters listed below may differ, as determined by your system configuration.
Menu
Field
Options
Disabled
[1.44/1.2 MB
3.5"]
Default
Description
[1.44/1.2 MB
3.5"]
Enables or disables a floppy disk drive.
Floppy
Disk A:
n
Primary
Master:
Selects Primary
Master submenu
The product #
of the Hard
Drive
Display the type of device on this ATA/ATAPI interface, if there is one. Pressing
the Enter key selects the Primary Master submenu allowing additional device
configuration options for this interface.
Secondary
Master:
Selects
Secondary
Master submenu
The product
number of the
CD-ROM
Display the type of device on this ATA/ATAPI interface, if there is one. Pressing
the Enter key selects the Secondary Master submenu allowing additional device
configuration options for this interface
Language:
n
English (US)
Japanese (JP)
[English (US)]
The default setting differs between the US/European and the Japanese model.
Selects the display language for the BIOS.
n
n
5
EarthlingBIOS.fm Page 6 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Primary Master Submenu of the Main Menu
The Primary Master submenu identifies what ATA
devices are installed.
*Note that actual hard drive label shown may vary.
Depending on the drive type, information such as cylinders, heads and sectors may also be displayed.
PhoenixBIOS Setup Utility
Main
Primary Master [TOSHIBA MK2018GAP -(PM)]
Type:
Select ATA/ATAPI drive
installed here.
[Auto]
LBA Format
39070080
20004MB
Total Sectors:
Maximum Capacity:
Multi-Sector Transfers:
LBA Mode Control:
PIO Transfer Mode:
DMA Transfer Mode:
Item Specific Help
[Auto]
The BIOS auto-types the
drive on boot time.
[16 Sectors]
[Enabled]
[Multiword DMA 2]
[Disabled]
Except [Auto]
You enter parameters of
the drive.
[None]
The drive is disabled.
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 2. Primary Master Submenu
Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu
Menu Field
Options
Type:
n
n
n
n
Auto
None
CD-ROM
Hard Disk
Default
Description
[Auto]
Selects the ATA/ATAPI device type. Select Auto to have the type
automatically identified by the BIOS at POST. If None is selected, all of the
following Set-up items do not appear. Select CD-ROM if a CD-ROM drive
is installed at this connection. If Hard Disk is selected, you must specify the
number of Cylinders, Heads, and Sectors for the drive.
CHS Format (Cylinders, Heads, Sectors)
6
Cylinders:
n
A number
between
0 and 65,535
–—
This appears only when Hard Disk is selected. When Hard Disk is selected,
you can change the value. This field is incremented by pressing the
[Spacebar]) or by pressing [Shift] [+]. This field is decremented by pressing
the [-] key. You can also change the field by typing in the number.
Heads:
n
A number
between
1 and 16
–—
This appears only when Hard Disk is selected. When Hard Disk is selected,
you can change the value. This field is incremented by pressing the
[Spacebar]) or by pressing [Shift] [+]. This field is decremented by pressing
the [-] key. The field can also be changed by typing in the number.
EarthlingBIOS.fm Page 7 Thursday, April 11, 2002 9:48 AM
Main Menu
Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu
Menu Field
Options
Default
Description
Sectors:
n
A number
between
0 and 63
–—
This appears only when Hard Disk is selected. When Hard Disk is selected,
you can change the value. This field is incremented by pressing the
[Spacebar]) or by pressing [Shift] [+]. This field is decremented by pressing
the [-] key. The field can also be changed by typing in the number.
Maximum
Capacity:
n
Display only
–—
Displays the maximum capacity of the drive calculated from the
parameters of the hard disk when Hard Disk is selected.
LBA Format (Logical Block Addressing)
Total Sectors:
–—
–—
The total number of sectors on your hard disk.
Maximum
Capacity
–—
–—
The maximum capacity of your hard disk.
Multi-Sector
Transfers:
n
Disabled
2 Sectors
4 Sectors
8 Sectors
16 Sectors
32 Sectors
64 Sectors
128 Sectors
[16 Sectors]
This option cannot be changed when Auto is selected. Specify the number
of sectors per block for multiple sector transfer. MAX refers to the size the
disk returns when required.
Disabled
Enabled
[Enabled]
Enables or disables Logical Block Addressing in place of Cylinder, Head,
Sector addressing. This cannot be changed when Auto is selected.
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
Multiword DMA 1
Multiword DMA 2
[Multiword
DMA 2]
Selects the method for moving data to/from the drive. Autotype the drive
to select the optimum transfer mode. This option cannot be changed
when Auto is selected. Multi-word DMA is automatically set to mode 1 for
Fast PIO 1, Fast PIO 2, Fast PIO 3, and set to mode 2 for Fast PIO 4 /
DMA.
Disabled
Mode 0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
[Mode 5]
Selects the method for moving data to/from the drive. Autotype the drive
to select the optimum transfer mode. This option cannot be changed
when Auto is selected.
n
n
n
n
n
n
n
LBA Mode
Control:
n
Transfer
Mode:
n
n
n
n
n
n
n
n
Ultra DMA
Mode:
n
n
n
n
n
n
n
7
EarthlingBIOS.fm Page 8 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
CAUTION
8
n
A bootable CD-ROM may have a floppy disk format
or a hard drive format. When the bootable CD-ROM
is used, the drive allocations change automatically
without changing the BIOS setup. If a floppy disk format CD-ROM is used, the CD-ROM becomes Drive
A. The CD-ROM will only take Drive C: (hard drive
format) if the internal hard drive is not present or is
disabled. The bootable CD-ROM can never use a C:
designation if a formatted internal hard drive is
present, since the C: designator is always reserved for
the internal hard drive.The boot sequence ignores the
new drive designations, but your application software
will use the new designations.
n
Be careful of the operating environment when booting from a CD-ROM or you may overwrite files by
mistake.
EarthlingBIOS.fm Page 9 Thursday, April 11, 2002 9:48 AM
Main Menu
Secondary Master Submenu of the Main Menu
The Secondary Master submenu is for the internal CDROM drive. The drive type is displayed on this menu as
well as the Main menu. Your notebook auto-senses the
characteristics of the internal CD-ROM Drive installed.
You will not need to modify these settings, they are
displayed for your reference.
Note that actual drive labels shown may vary.
PhoenixBIOS Setup Utility
Main
Secondary Master [TOSHIBA DVD-ROM -SD-R2102 -(SM)]
Type:
[Auto]
Multi-Sector Transfers:
LBA Mode Control:
Transfer Mode:
Ultra DMA Mode:
[Disabled]
[Disabled]
[Multiword DMA 2]
[Disabled]
Item Specific Help
Select ATA/ATAPI drive
installed here.
[Auto]
The BIOS auto-types the
drive on boot time.
Except [Auto]
You enter parameters of
the drive.
[None]
The drive is disabled.
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 3. Primary Slave Submenu
Table 3: Fields, Options and Defaults for the Primary Slave Submenu of the Main Menu
Menu Field
Options
Type:
n
n
n
n
Multi-Sector
Transfers:
n
n
n
n
n
LBA Mode
Control:
n
n
Default
Description
Auto
None
CD-ROM
Hard Disk
[Auto]
Selects the ATA/ATAPI device type. Select Auto to have the type
automatically identified by the BIOS at POST. If None is selected, all
of the following Set-up items do not appear. Select CD-ROM or
Hard Disk for appropriate drive type installed at this connection.
Disabled
2 Sectors
4 Sectors
8 Sectors
16 Sectors
[Disabled]
This option cannot be changed when Auto is selected. Specify the
number of sectors per block for multiple sector transfer.
Disabled
Enabled
[Disabled]
Enables or disables Logical Block Addressing in place of Cylinder,
Head, Sector addressing. This option cannot be changed when
Auto is selected.
9
EarthlingBIOS.fm Page 10 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Table 3: Fields, Options and Defaults for the Primary Slave Submenu of the Main Menu
Menu Field
Options
Transfer Mode:
n
n
n
n
n
n
n
Ultra DMA Mode:
n
n
n
n
n
n
n
Default
Description
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
Multiword DMA 1
Multiword DMA 2
[Standard]
Selects the method for moving data to/from the drive. Autotype
the drive to select the optimum transfer mode. This option cannot
be changed when Auto is selected. Multi-word DMA is
automatically set to mode 1 for Fast PIO 1, Fast PIO 2, Fast PIO 3,
and set to mode 2 for Fast PIO 4/DMA.
Disabled
Mode 0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
[Disabled]
Selects the method for moving data to/from the drive. Autotype
the drive to select the optimum transfer mode. This option cannot
be changed when Auto is selected.
Exiting from Main Menu
When you have finished setting the parameters on this
menu, you can either exit from the setup utility, or move
to another menu. If you wish to exit from the setup
utility, press the [Esc] key or use the cursor keys to go to
the Exit menu. If you wish to move to another menu, use
the cursor keys.
10
EarthlingBIOS.fm Page 11 Thursday, April 11, 2002 9:48 AM
Advanced Menu
ADVANCED MENU – SETTING DEVICE FEATURE CONTROLS
The Advanced Menu allows you to:
n
Set the I/O addresses for the ports.
n Set the communication mode for the parallel and
infrared ports.
n Set the features of the keyboard/mouse.
n
Select between the display panel and an external
CRT display.
n
Configure IDE devices in your system.
n
Configure CPU features.
n Configure USB features.
n
Configure the power button.
n
View DMI Event Logging
Main
Advanced
Follow the instructions for Navigating Through the
Setup Utility to make any changes.
(See Navigating Through The Setup Utility on page 2 for
more information.)
The following tables show the names of the menu fields
for the Advanced Menu and its submenus, all of the
options for each field, the default settings and a description of the field’s function and any special information
needed to help understand the field’s use.
Note that not all fields appear in all configurations; the
fields that appear are dependent upon the system CPU.
PhoenixBIOS Setup Utility
Security
Power
Boot
Info
Exit
Item Specific Help
▲ ▲ ▲ ▲ ▲ ▲ ▲
Serial/Parallel Port Configurations
Keyboard/Mouse Features
Video Features
Internal Device Configurations
CPU Features
USB Features
Miscellaneous Configurations
▲
Event Logging
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
Configures serial ports
and parallel ports.
F9 Setup Defaults
F10 Save and Exit
Figure 4. Advanced Menu
11
EarthlingBIOS.fm Page 12 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Table 4: Fields, Options and Defaults for the Advanced Menu
Menu Field
Options
Default
Description
Serial/Parallel Port
Configurations
–—
–—
When selected, opens the Serial/Parallel Port Configurations
submenu which allows the user to modify settings for the parallel
port.
Keyboard/Mouse
Features
–—
–—
When selected, opens the Keyboard/Mouse Features submenu,
which enables and disables the power-on state for [Numlock].
Video Features
–—
–—
When selected, opens the Video Features submenu, which allows
setting of the display parameters, including routing of video signals
to different displays.
Internal Device
Configurations
–—
–—
When selected, opens the Internal Device Configuration submenu,
which allows enabling or disabling the IDE Controller.
CPU Features
–—
–—
When selected, opens the CPU Features submenu, which allows
enabling or disabling the SpeedStep™ Technology feature for
optimal battery life.
USB Features
–—
–—
When selected, opens the USB Features submenu, which allows
enabling or disabling of Legacy Floppy Emulation.
Miscellaneous
Configurations
–—
–—
When selected, opens the Miscellaneous Configurations submenu,
which allows you to configure the power button.
Event Logging
–—
–—
When selected, opens the event logging submenu.
12
EarthlingBIOS.fm Page 13 Thursday, April 11, 2002 9:48 AM
Advanced Menu
Serial/Parallel Port Configuration Submenu of the Advanced Menu
The Serial/Parallel Port Configuration submenu
provides the ability to set the I/O addresses and interrupt levels for the parallel port of your notebook.
P O I N TS
n
To prevent IRQ and address conflicts, avoid changing
the default settings. If you must change the settings,
you can call 1-800-8FUJITSU for technical assistance.
n
The BIOS will warn you of a resource conflict by placing a yellow asterisk next to each device that is in
conflict.
n
All I/O addresses in Table 5 are in hexadecimal.
CAUTION
I/O addresses, DMA channels, and Interrupt levels can
be entered in various ways, including via the BIOS setup
utility, the control software for the I/O device, or the
hardware. If any two ports or devices have the same
I/O address assigned, your notebook will not function
normally. Please keep a record of original settings
before making any changes in the event that a
restoration is required. See your hardware and software
documentation as well as the setup utility to determine
settings, limitations, etc.
PhoenixBIOS Setup Utility
Advanced
Item Specific Help
Serial/Parallel Port Configurations
Parallel Port:
Mode:
I/O Address:
Interrupt:
[Enabled
[Bi-directional]
[378-37F]
[IRQ 7]
[Disabled]
The port is disabled.
[Enabled]
The port is enabled
with user configuration.
[Auto]
The port is configured
depending on 'Plug &
Play OS' setting.
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 5. Serial/Parallel Port Configuration Submenu
13
EarthlingBIOS.fm Page 14 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Table 5: Fields, Options and Defaults for the Port Configuration Submenu of the Advanced Menu
Menu Field
Options
Parallel Port:
n
n
n
Mode:
n
n
n
I/O address:
n
n
n
Interrupt:
n
n
14
Default
Description
Disabled
Enabled
Auto
[Enabled]
Configures the parallel port using either no configuration
(Disabled), a user defined configuration (Enabled), or by
allowing the BIOS or OS to choose the configuration (Auto).
Output Only
Bi-directional
ECP
[Bi-directional]
When the parallel port is enabled this option is available allowing
the user to set the mode for the parallel port. Bi-directional allows
two-way transfer of information between your notebook and a
connected parallel device. Output Only (Half Duplex) allows
information to be transferred in only one direction, from your
notebook to the printer or similar device. ECP Mode allows
communication with the ECP class of parallel I/O devices.
378 - 37F
278 - 27F
3BC - 3BF
[378 - 37F]
Allows user to set the parallel port base I/O address when the
parallel port is Enabled.
IRQ 5
IRQ 7
[IRQ 7]
Allows user to set the parallel port interrupt when the parallel
port is Enabled.
EarthlingBIOS.fm Page 15 Thursday, April 11, 2002 9:48 AM
Advanced Menu
Keyboard/Mouse Features Submenu of the Advanced Menu
The Keyboard/Mouse Features submenu is for selecting
the power-on state for the Numlock key.
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Item Specific Help
Keyboard/Mouse Features
Numlock:
Select Item
Select Menu
Select power-on state
for Numlock.
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
[Off]
F9 Setup Defaults
F10 Save and Exit
Figure 6. Keyboard/Mouse Features Submenu
Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu
Menu Field
Options
Numlock:
n
n
On
Off
Default
Description
[Off]
Sets the NumLock function state when the computer
completes booting.
15
EarthlingBIOS.fm Page 16 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Video Features Submenu of the Advanced Menu
The Video Features Submenu is for choosing the display.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Item Specific Help
Video Features
Display:
Compensation:
Select Item
Select Menu
Select display terminal.
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
[Internal Flat Panel]
[Disabled]
F9 Setup Defaults
F10 Save and Exit
Figure 7. Video Features Submenu
Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu
Menu Field
Options
Display:
n
n
n
Compensation:
n
n
16
Default
Description
Internal
Flat Panel
External
Simultaneous
[Internal Flat Panel]
Selects where the video signal will be routed.
Disabled
Enabled
[Disabled]
Enables or disables video compensation.
EarthlingBIOS.fm Page 17 Thursday, April 11, 2002 9:48 AM
Advanced Menu
Internal Device Configurations Submenu of the Advanced Menu
The Internal Device Configurations submenu allows the
user to enable or disable IDE ports.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Item Specific Help
Internal Device Configurations
IDE Controller
[Both]
[Disabled]
No IDE ports are enabled
[Primary]
Only primary IDE port
is enabled.
[Secondary]
Only secondary IDE port
is enabled.
[Both]
Both primary and
secondary IDE ports
are enabled.
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 8. Internal Device Configuration Submenu
Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu
Menu Field
Options
IDE Controller:
n
n
n
n
Disabled
Primary
Secondary
Both
Default
Description
[Both]
Enables or disables IDE controllers.
17
EarthlingBIOS.fm Page 18 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
CPU Features Submenu of the Advanced Menu
The CPU Features Submenu configures the system
processor.
Main
Note that this submenu only appears in certain
configurations, based upon the system CPU.
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
Item Specific Help
CPU Features
SpeedStep(TM) Technology:
On Battery:
On AC:
Select Item
Select Menu
Select Enhanced
Intel(R) SpeedStep(TM)
Technology enabled or
disabled.
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
[Enabled]
[Battery Optimized]
[Maximum Performance]
F9 Setup Defaults
F10 Save and Exit
Figure 9. CPU Features Submenu
Menu Field
Options
Default
Description
SpeedStep(TM)
Technology:
• Disabled
• Enabled
[Enabled]
When Disabled is selected, CPU speed is fixed to battery optimized speed. When Enabled is selected, CPU
speed and battery use can be selected from On Battery and On AC.
On Battery:
•
•
•
•
Maximum Performance
Battery Optimized
Maximum Battery
Automatic
[Battery Optimized]
When Maximum Performance is selected, CPU speed
is maximized. When Battery Optimized is selected,
CPU power requirements are optimized for battery
operation. When Maximum Battery is selected, CPU
speed is optimized for battery operation. When Automatic is selected, the CPU speed is determined by the
power source used.
On AC:
•
•
•
•
Maximum Performance
Battery Optimized
Maximum Battery
Automatic
[Maximum Performance]
When Maximum Performance is selected, CPU speed
is maximized. When Battery Optimized is selected,
CPU power requirements are optimized for battery
operation. When Maximum Battery is selected, CPU
speed is optimized for battery operation. When Automatic is selected, the CPU speed is determined by the
power source used.
18
EarthlingBIOS.fm Page 19 Thursday, April 11, 2002 9:48 AM
Advanced Menu
USB Features Submenu of the Advanced Menu
The USB Features Submenu configures the system for
use with a USB floppy drive.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Item Specific Help
USB Features
USB Floppy Disk:
[Disabled]
[Disabled]
Legacy Floppy Emulation
is disabled.
[Enabled]
Legacy Floppy Emulation
is enabled, and USB
floppy is available
without a USB-aware OS.
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 10. USB Features Submenu
Table 10: Fields, Options and Defaults for the USB Features Submenu of the Advanced Menu
Menu Field
Options
USB Floppy Disk:
n
n
Disabled
Enabled
Default
Description
[Disabled]
When Enabled is selected, Legacy Floppy Emulation is enabled and
the USB floppy drive and bootable support are available without a
USB-aware OS. When Disabled is selected, Legacy Floppy
Emulation is disabled.
19
EarthlingBIOS.fm Page 20 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Miscellaneous Configurations Submenu of the Advanced Menu
The Miscellaneous Configurations Submenu configures
the power button.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Item Specific Help
Miscellaneous Configurations
Power Button:
[Disabled]
Configures the power
button.
*ACPI OS ignores this
setting.
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 11. Miscellaneous Configurations Submenu
Table 11: Fields, Options and Defaults for the Miscellaneous Configuration Submenu of the Advanced Menu
Menu Field
Options
Power Button:
n
n
20
Disabled
Power Off
Default
Description
[Disabled]
When Disabled is selected, the power button does not control
power. When Power Off is selected, pressing the power button
shuts off power to the system.
EarthlingBIOS.fm Page 21 Thursday, April 11, 2002 9:48 AM
Advanced Menu
Event Logging Submenu of the Advanced Menu
The Event Logging Submenu configures event logging features for DMI events.
Main
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
Item Specific Help
Event Logging
Event Log Capacity:
Event Log Validity:
Space Available
Valid
View Event Log:
[Enter]
Event Logging:
System Boot Event:
[Enabled]
[Disabled]
Clear All Event Logs:
[No]
Mark Events as Read:
[Enter]
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
Press <Enter> key to
view the contents of
the event log.
F9 Setup Defaults
F10 Save and Exit
Figure 12. Event Logging Submenu
Table 12: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Event Log
Capacity:
Space Available
Display only
Event Log Validity:
Valid
Display only
View Event Log:
n
Enter
[Enter]
Allows you to view content of event log
Event Logging:
n
Disabled
Enabled
[Enabled]
Turns event logging on and off for all DMI events.
Disabled
Enabled
[Disabled]
Turns event logging on and off for DMI system boot events.
No
Yes
[No]
When set to [Yes] all event logs will be cleared at next boot.
Enter
[Enter]
Allows you to make all events currently in the event log as having
been read.
n
System Boot
Event:
n
n
Clear All Event
Logs:
n
Mark Events as
Read:
n
n
21
EarthlingBIOS.fm Page 22 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
SECURITY MENU – SETTING THE SECURITY FEATURES
The Security menu allows you to set up the data security
features of your notebook to fit your operating needs and
to view the current data security configuration. Follow the
instructions for Navigating Through the Setup Utility to
make any changes. (See Navigating Through The Setup
Utility on page 2 for more information.)
The following tables show the names of the menu
fields for the Security menu and its submenus, all of
the options for each field, the default settings and a
description of the field's function and any special
information needed to help understand the field's use.
The default condition is no passwords required and no
write protection.
POINT
n
If you set a password, write it down and keep it in a
safe place. If you forget the password, you will have
to contact your support representative to regain
access to your secured functions and data.
n
Entering a password incorrectly 3 times in a row will
cause the keyboard and mouse to be locked out and
the warning [System Disabled] to be displayed.
If this happens restart the computer by turning the
power off and on with the power switch and use the
correct password on reboot.
22
P O I N TS
n
If you make an error when re-entering the password
a [Warning] will be displayed on the screen. To try
again press the Enter key and then retype the password. Press the Esc key to abort the password setting
process.
n
If Password On Resume is Enabled and Password On
Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or
Save-to-Disk modes. Password On Resume will work
only if Password On Boot is enabled.
n
Boot sector protection must be set to [Normal] to
install or upgrade an operating system.
EarthlingBIOS.fm Page 23 Thursday, April 11, 2002 9:48 AM
Security Menu
Main
PhoenixBIOS Setup Utility
Security
Power
Boot
Advanced
Info
Exit
Item Specific Help
Supervisor Password Is:
User Password Is:
Clear
Clear
Set Supervisor Password
Set User Password
Minimum User Password Length:
[Enter]
[Enter]
[0]
Press [Enter] key to
set Supervisor Password
to enable any password
features.
Password on Boot:
KB Lock on Resume:
Boot from Removable Media:
[Disabled]
[Disabled]
[All]
Then password entry is
required to enter BIOS
Setup.
▲▲
Hard Disk Security
Owner Information
Select Item
Select Menu
-/Space Change Values
Enter Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 13. Security Menu
Table 13: Fields, Options and Defaults for the Security Menu
Menu Field
Options
Default
Description
Supervisor
Password is:
–—
Clear
A display-only field. Set is displayed when the system supervisor
password is set and Clear when it is not.
User Password is:
–—
Clear
A display-only field. Set is displayed when the general user
password is set, and Clear when it is not.
Set Supervisor
Password
–—
[Enter]
Sets, changes or cancels the Supervisor Password. The Supervisor
Password may be up to seven characters long and must include
only letters or numbers (no symbols). Passwords are NOT casesensitive. To cancel a password press the Enter key instead of
entering characters in the Enter New Password field and in the
Re-enter New Password field. When a Supervisor Password is set
it must be used to access the BIOS setup utility.
Set User Password
–—
[Enter]
This field can only be accessed if the Supervisor Password is set.
This field sets, changes or cancels the User Password. The User
Password may be up to seven characters long and must include
only letters or numbers (no symbols). Passwords are NOT casesensitive. To cancel a password press the Enter key instead of
entering characters in the Enter New Password field and in the Reenter New Password field. When a User Password is set it must be
used to access the BIOS setup utility.
Minimum User
Password Length:
–—
[0]
23
EarthlingBIOS.fm Page 24 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Table 13: Fields, Options and Defaults for the Security Menu
Menu Field
Options
Password on Boot:
n
n
n
Default
Description
Disabled
First Boot
Every Boot
[Disabled]
When set to DIsabled, no password is required. When set to First
Boot, a password (User or Supervisor) is required after the Power
On Self Test (POST) before the operating system will be read from a
disk. If Every Boot is set, a password (User or Supervisor) is required
after the Power On Self Test (POST) every time the system is
booted (before the operating system is read from the disk).
Disabled
Enabled
[Disabled]
When set to Enabled, the PS/2 mouse and keyboard inputs are
locked out upon Resume from Suspend or Save to Disk mode until
you enter the password. When set to Disabled no password is
required. If no Supervisor Password is set, this feature is not
available and no password is required.
All
Supervisor only
[All]
Enable password allows supervisor access only.
KB Lock on
Resume:
n
Boot from
Removable Media:
n
Hard Disk Security:
–—
–—
Configures hard disk security features
Owner
Information:
–—
–—
Sets Owner information.
24
n
n
EarthlingBIOS.fm Page 25 Thursday, April 11, 2002 9:48 AM
Security Menu
Hard Disk Security Submenu of the Security Menu
The Hard Disk Security Submenu is for configuring
hard disk security features.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Hard Disk Security
Primary Master:
Secondary Master:
[Disabled]
[Disabled]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Item Specific Help
F9 Setup Defaults
F10 Save and Exit
Figure 14. Hard Disk Security Submenu
Table 14: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu
Menu Field
Options
Primary Master:
n
n
Secondary Master:
n
n
Default
Description
Disabled
Enabled
[Disabled]
Disabled: No password protection.
Enabled: The hard disk is locked with the password. Data in the
locked disk cannot be read on any systems other than the original
system on which it is locked or systems that have the identical
password setting.
Disabled
Enabled
[Disabled]
25
EarthlingBIOS.fm Page 26 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
Owner Information Submenu of the Security Menu
The Owner Information Submenu is for setting owner
information.
Main
Note: This submenu can be modified only if a Supervisor’s
Password has been set previously.
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
Owner Information
Owner Information Is:
Set Owner Information
Clear
[Enter]
Foreground Color:
Background Color:
[Gray]
[Black]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
▲
F1 Help
ESC Exit
Item Specific Help
Figure 15. Owner Information Submenu
Table 15: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu
Menu Field
Options
Default
Description
Owner Information Is:
–—
Clear
Display only.
Set Owner
Information:
–—
[Enter]
Field to write owner
information (i.e., name).
Foreground Color:
n
Light Cyan
Light Red
Light Magenta
Yellow
Bright White
[Gray]
Select a color for the
foreground.
Light Cyan
Light Red
Light Magenta
Yellow
Bright White
[Black]
Select a color for the
background.
n
n
n
n
n
Background Color:
n
n
n
n
n
n
Black
Blue
Green
Cyan
Red
Magenta
n
Black
Blue
Green
Cyan
Red
Magenta
n
n
n
n
n
n
n
n
n
Brown
White
Gray
Light Blue
Light Green
n
Brown
White
Gray
Light Blue
Light Green
n
Exiting from the Security Menu
When you have finished setting the parameters on the
Security Menu, you can either exit from setup utility or
26
n
n
n
n
n
n
n
n
move to another menu. If you wish to exit from setup
utility, press the Esc key to go to the Exit Menu. If you
wish to move to another menu, use the cursor keys.
EarthlingBIOS.fm Page 27 Thursday, April 11, 2002 9:48 AM
Boot Menu
BOOT MENU – SELECTING THE OPERATING SYSTEM SOURCE
The Boot Menu is used to select the order in which the
BIOS searches sources for the operating system. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating Through
The Setup Utility on page 2 for more information.)
Main
Advanced
The following tables show the names of the menu fields
for the Boot menu and its submenu, all of the options
for each field, the default settings and a description of
the field's function and any special information needed
to help understand the field's use.
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
Info
Exit
Item Specific Help
▲
Quick Boot:
Boot Time Diagnostic Screen:
[Enabled]
[Disabled]
Preboot Execution Environment:
Boot Device Priority
[Enabled]
[Disabled]
All diagnostic tests
will be done.
[Enabled]
Some diagnostic tests
may be skipped while
booting to speed up.
Select Item -/Space Change Values
Select Sub-Menu
Select Menu Enter
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 16. Boot Menu
Table 16: Fields, Options and Defaults for the Boot Menu
Menu Field
Options
QuickBoot Mode:
n
n
Boot-time
Diagnostic Screen:
n
Preboot Execution
Environment
n
Boot Device
Priority
n
n
n
Default
Description
Disabled
Enabled
[Enabled]
When [Disabled] is selected, all diagnostic tests are performed
when the system is booted up. If [Enabled] is set, some of the tests
are skipped in order to speed up the booting process.
Disabled
Enabled
[Disabled]
Turns on and off display of test results instead of Fujitsu logo screen
during Power On Self Test.
Disabled
Enabled
[Enabled]
Turns on and off boot from network server options.
Selects the Boot
Device Priority
submenu
—
This menu allows setting up the source for the operating system.
27
EarthlingBIOS.fm Page 28 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
The Boot Device Priority Submenu of the Boot Menu
The Boot Device Priority Submenu is for setting the
order of checking of sources for the operating system.
Main
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
Advanced
Boot Device Priority
Item Specific Help
+Floppy Disk Drive
+Hard Disk Drive
CD-ROM Drive
Realtek Boot Agent
<Enter> expands or
collapses devices with
a + or -.
<Ctrl+Enter> expands
all.
<Shift+1> enables or
disables a device.
<+>/<Space> or <->
moves the device up or
down.
<d> removes a device
that is not installed.
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Keys used to view or
configure devices:
F9 Setup Defaults
F10 Save and Exit
Figure 17. Boot Device Priority Submenu
Table 17: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu
Menu Field
Options
Default
Description
+Floppy Disk Drive
–—
–—
+Hard Disk Drive
–—
–—
CD-ROM Drive
–—
–—
The boot selections determine the order in which the BIOS searches for the
operating system during a startup sequence. To view all devices related to a source,
press [Enter]; to view all devices related to all sources, press [Ctrl] + [Enter]. To
change the order, highlight one source by using the [up] or [down] cursor keys and
then press the [+] or [-] key to change the order number for that source. [Shift] +
[1] enables a device.Tapping [d] removes from the list a device that is not
installed.Be sure to save your changed order when you exit the BIOS setup utility.
Realtek Boot Agent
NOTE: Be aware that if you use the CD-ROM drive as the first boot device, certain
files may be overwritten, depending upon your operating environment.
Exiting from Boot Menu
When you have finished setting the boot parameters with
the Boot menu, you can either exit from the setup utility
or move to another menu. If you wish to exit from the
setup utility press the Esc key to go to the Exit menu. If
you wish to move to another menu, use the cursor keys.
28
EarthlingBIOS.fm Page 29 Thursday, April 11, 2002 9:48 AM
Info Menu
INFO MENU - DISPLAYS BASIC SYSTEM INFORMATION
The Info menu is a display only screen that provides the
configuration information for your notebook.
The following table shows the names of the menu fields
for the Info menu and the information displayed in
those fields. These fields are for information purposes
only, and cannot be modified by the user.
Main
POINT
The information, including CPU type and speed, and
total memory, displayed on this screen varies according
to the unit you purchased.
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
Advanced
Info
Exit
Item Specific Help
BIOS Version:
BIOS Date:
BIOS Area:
1.06
04/01/2002
E400h - FFFFh
CPU Type:
CPU Speed:
L1 Cache:
L2 Cache:
Pentium(R) 4 processor-M
1.60 GHz
8 KB
512 KB
Total Memory:
Onboard Memory:
Memory Slot:
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
256 MB
256 MB DDR SDRAM
None
F9
F10
Setup Defaults
Save and Exit
Figure 18. Info Menu
Table 18: Fields, Options and Defaults for the Info Menu
Note that some of the parameters reflected below may be different from those on your screen, depending upon system
configuration.
Menu Field
Default
Menu Field
Default
BIOS Version:
1.06
L1 Cache:
8 KB
BIOS Date:
04/01/2002
L2 Cache:
512 KB
BIOS Area:
E400h – FFFFh
Total Memory:
256 MB
CPU Type:
Pentium(R) 4 processor-M
Onboard Memory
256 MB DDR SDRAM
CPU Speed:
1.60 GHz
Memory Slot
None
29
EarthlingBIOS.fm Page 30 Thursday, April 11, 2002 9:48 AM
LifeBook C Series BIOS
EXIT MENU – LEAVING THE SETUP UTILITY
The Exit Menu is used to leave the setup utility. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating Through
The Setup Utility on page 2 for more information.)
Main
The following table shows the names of the menu fields
for the Exit menu, the default settings and a description
of the field's function and any special information
needed to help understand the field's use.
PhoenixBIOS Setup Utility
Security
Power Savings
Advanced
Boot
Exit
Item Specific Help
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Exit System Setup and
save your changes to
CMOS.
F9
F10
Setup Defaults
Save and Exit
Figure 19. Exit Menu
Table 19: Fields, Options and Defaults for the Exit Menu
Optional Keyboard
Shortcut
Default
Description
Exit Saving
Changes
Press F10 key
–—
Exit Saving Changes and Exit will store all the entries on every
menu of the setup utility to the BIOS memory and then exit the
setup utility. A confirmation message Save Configuration
changes and exit now? [Yes] [No] will be displayed.
Exit Discarding
Changes
–—
–—
Selecting Exit Discarding Changes and Exit will exit the setup
utility with out writing to the BIOS memory. A setup warning
message Configuration has not been saved! Save
before exiting? [Yes] [No] will be displayed when your
settings have changed. When the BIOS recognizes the Exit
Discarding Changes selection it will load the operating system and
begin operation.
Menu Field
30
EarthlingBIOS.fm Page 31 Thursday, April 11, 2002 9:48 AM
Exit Menu
Table 19: Fields, Options and Defaults for the Exit Menu
Optional Keyboard
Shortcut
Default
Description
Load Setup
Defaults
Press F9 key
–—
Selecting Load Setup Defaults will load the factory preset default
values for all menu fields, then display the message Load
default configuration now? [Yes] [No]. When
confirmed the setup utility will return to the Exit Menu. To return to
another menu follow the directions in the Navigating Through the
Setup Utility Section.
Discard Changes
–—
–—
Selecting Discard Changes will load the previous values in BIOS
memory for all menu fields. The message Load previous
configuration now? [Yes] [No] will be displayed. When
confirmed the setup utility will return to the Exit menu. To return to
another menu, follow the directions in the Navigating Through the
Setup Utility Section.
Save Changes
–—
–—
Selecting Save Changes will cause the new settings in all menus to
be written to the BIOS memory. The message Save
configuration changes now? [Yes] [No] will be
displayed. When confirmed, the setup utility will return to the Exit
menu. To return to another menu, follow the directions in the
Navigating Through the Setup Utility section.
Menu Field
31