Airlink101 AGSW1600 Switch Installation guide
Add to my manuals13 Pages
Airlink101 AGSW1600 is a 16-port 10/100/1000Mbps Green Switch designed for energy saving, easy installation, and high performance. It allows you to expand your network quickly and reliably, adding devices like computers, IP cameras, and Network Attached Storage (NAS). The Green EEE technology automatically reduces power usage when a port is inactive or connected to a shorter cable, saving energy. With its comprehensive LED indicators, you can easily monitor the status of your network and troubleshoot any issues. The AGSW1600 is rack-mountable, making it suitable for professional installations.
advertisement
Quick Installation Guide
16-Port 10/100/1000Mbps
Green Switch
Model# AGSW1600
Ver. 1A
Trademarks
Copyright © 2011 Airlink101®
Airlink101® is a registered trademark. All other trademarks belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Phoebe Micro, Inc.
Preface
FCC Warning
This device has been tested and found to comply with limits for Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the user’s manual, may cause interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
1
Introduction
Congratulations on your purchase of the 16-Port
10/100/1000Mbps Green Switch! It is an easy-installed network switch which helps you to extend your network structure quickly and reliably. The 16-Port 10/100/1000Mbps
Green Switch is designed for energy saving, easy installation and high performance in an environment where network traffic and the number of users increase continuously. You can add other Ethernet devices like computers, IP cameras, and Network Attached Storage (NAS) onto your network quickly and easily. The Green EEE (Energy Efficient Ethernet) technology of AGSW1600 automatically reduces the power usage when a connected port is detected inactive (idle or cable-unplugged) and intelligently allocates less power for a port that connects with an Ethernet cable shorter than 20m
(66 ft)*.
Before you begin the installation, please check the items of your package:
Package Contents:
• 16-Port 10/100/1000Mbps Green Switch
Cord
• Quick Installation Guide
2
Section 1
Hardware Description
1.1 Hardware Interface
cross-over cables
1.2 Panel
1.2.1 Front Panel
The front panel of the Switch consists of LED indicators, and
16 10/100/1000Mbps ports. The figure below shows the front panel of the Switch.
Figure 1-1 Front Panel view of the Switch
• 10/100/1000Mbps Ports (Port 1~16): These ports support
10/100/1000Mbps, and can operate in Half/Full Duplex transfer modes. These ports also support automatic
MDI/MDI-X crossover detection, giving true “plug and play” capability.
• LED Indicators: Comprehensive LED indicators display the status of the Switch and the network (see Section
1.2.3).
3
1.2.2 Rear Panel
Figure 1-2 Rear Panel view of the Switch
• AC Power Connector: Supports AC 100~240V, 50~60Hz.
NOTICE:
Do not cover or put anything on or surrounding the Switch while the Switch is operating.
1.2.3 LED indicators information
The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed.
Figure 1-3 Front Panel view of the Switch
4
• POWER: Power Indicator
LED Color
Solid
Status
Blinking Off
LED Color
power-on
• Port 1~16 10/100/1000Mbps Status LEDs
Status
LINK/
ACT
10/100M
Green
Solid
The respective port is successfully connected to the
10/100Mbps
Ethernet network
Blinking
The port is transmitting or receiving data at
10/100Mbps
LED Color
Status
Blinking
LINK/
ACT
1000M
Blue
Solid
The respective port is connected to the 1000Mbps
Ethernet network
The port is transmitting or receiving data at above
100Mbps
Off
No link
Off
No link
5
Section 2
Installing the Switch
The site where you place the Switch may greatly affect its performance.
2.1 Installation
Please follow the guidelines below to install the Switch:
• Please install the Switch in a fairly cool and dry place.
Please refer to the Technical Specifications for the acceptable temperature and humidity operating ranges.
• Please install the Switch on a sturdy, level surface that can support its weight.
• When connecting the power cord to the Switch and the power outlet, the distance should be no more than
182cm.
• Please leave at least 10cm (about 4 inches) of space at the front and rear of the Switch for ventilation.
2.2 Desktop or Shelf Installation
When installing the Switch on the desktop or shelf, please attach the rubber feet to the Switch. Peel off the protective paper on the pads and attach them to the bottom of the
Switch (one at each corner).
6
2.3 Rack Installation
The Switch is rack-mountable and can be installed on an EIA
11-inch equipment rack. To do this, first install the mounting brackets on the Switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the
Switch.
2.4 Power on the Switch
The Switch has a universal power supply ranging from 100V to 240V AC, 50 ~ 60Hz power source. The AC power connector is located at the rear of the unit. The switch’s power supply will adjust to the local power source automatically.
7
Section 3
Connecting the Switch
This section describes how to connect the Switch to your
10/100/1000Mbps Ethernet network.
Your network device (i.e. computer, switch, IP Camera, VoIP) can be connected to any port of the Switch via a two-pair
UTP Category 5 Cable. If the LED indicators do not light up after making a proper connection, check your network device, the cable, the Switch conditions and connections.
8
Section 4
Troubleshooting
1. Power LED is not lit
• Check if the power adapter is properly connected to the power outlet. Make sure the power jack is firmly plugged into the power socket of the switch.
2. Link/Activity is not lit when connect to 10/100/1000Mbps device
• Check the power switch of the network device attached to the switch; make sure it is turned ON.
• Check the network cable; make sure it is properly connected to the switch and the network device.
• Check the network cable; make sure the UTP cables comply with the specifications described in Section 2.
9
Section 5
Technical Specifications
Standards
IEEE802.3ab 1000BASE-T Gbit. IEEE 802.3x Flow
Control and IEEE 802.3az(EEE – Energy Efficient
Ethernet)
Network Cables
• Ethernet (10Base-T): Cables: 2-pair UTP Cat. 3, 4, 5,
Twisted Pair (UTP). Up to 100m
• Fast and Giga Ethernet (100/1000Base-T): 2-pair UTP
Cat. 5, Twisted Pair (UTP). Up to 100m
Ports
Access Method
• CSMA/CD
Transmission Method
MAC Address Table
• 8K
Jumbo Frame
• 9216-byte jumbo packet length forwarding at wire speed
Data Transfer Rate**
10
LED
Rack Mount
• 11-Inch Rack-Mountable with mounting kits
Dimensions
Weight
• 1200g
Physical and Environmental
• Power Input: 100~240V AC, 50~60Hz
• Operation Temperature: 0 °C ~ 40°C(32 ~ 104°F)
• Storage Temperature: -20°C ~ 70°C(-4 ~ 158°F)
• Humidity: 5% ~ 90% RH, non-condensing
Certification
11
Section 6
Technical Support
E-mail: [email protected]
Toll-Free: 1-888-746-3238*
Web Site: www.airlink101.com
* Free Voice Technical Support is only available within the hardware warranty
(1-Year Limited Warranty from the date of purchase). Customer is required to provide invoice as purchase evidence.
**Network conditions and environmental factors as well as network overhead can lower actual data throughput rate.
Copyright © 2011 AirLink101
®
. All rights reserved. AirLink101, the stylized
AirLink101
®
logo, specific product designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of AirLink101
®
. All other product or service names are the property of their respective holders. AirLink101 products are protected under numerous U.S. and foreign patents and pending applications, mask work rights, and copyrights.
12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project