Airlink101 AICN500W Security Camera User Manual

Airlink101 AICN500W Security Camera User Manual
Quick Installation Guide
SkyIPCam777W
Wireless MPEG4 Night Vision Pan & Tilt
Network Camera
Model # AICN777W
Ver. 1A
Package Contents:
•
•
•
•
•
•
•
•
Wireless MPEG4 Night Vision Pan & Tilt Network Camera
Antenna
Wall Mount Kit
GPIO Connector
Power Adapter
Ethernet Cable (Cat.5)
Utility CD
Quick Installation Guide
Section 1
This Quick Installation Guide only provides basic instructions. For detailed
information on using this product, please refer to the User’s Manual on the
supplied CD.
Getting Started
Step 1 Connect one end of the Ethernet cable to the IP Camera and connect
the other end to one of the LAN ports on your router or switch.
Step 2 Power on the IP Camera by connecting one end of supplied power
adapter to the power jack of the Camera and connecting the other end to the
electrical outlet.
Step 3 Verify that the yellow light (Power) is solid and the green light (Link) is
blinking.
Section 2
Installing the SkyIPCam Utility
Step 1 Insert the provided CD and wait for the auto-run screen to appear.
Step 2 Click on Install SkyIPCam Utility.
Note: If the auto-run screen does not appear automatically, go to Start, Run,
type: D:\ Utility\Setup.exe (where D is the letter of your CD drive) and click OK.
Step 3 Follow the installer instruction by clicking Next on the following screens.
Step 4 Click Close to complete the installation.
Section 3
Using the SkyIPCam Utility
Step 1 Go to Start > (All) Programs > AirLink101 > AirLink101 SkyIPCam
Utiliy
Step 2 Select the IP Camera you want to configure from the list and click on the
Change IP button.
Note: If the Camera’s IP address does not show up in the window, make sure
the camera is properly connected to the same network as your computer is,
and then click on the Search button.
Step 3 You may accept the suggested Static IP, or you can manually change
the last 3-digit number of the IP Address, in case the suggested address is
already being used by another device in the same network. Alternatively, if your
router’s DHCP server is enabled, you can select DHCP, and the router will
automatically assign a dynamic IP address to your camera.
Enter “admin” for both ID and password, and click Change.
Step 4 Once the changes have been saved, the Utility will return to the original
screen. Select your camera from the list and click Link.
Step 5 When you are prompted for the username and password, enter
“admin” for both User name and Password, and click OK.
Step 6 The camera viewing window will appear. Click on Setup, and then click
on Smart Wizard.
Step 7 If desired, you may change the default Camera Name and enter a
name for the Location. Then enter “admin” for both Admin Password and
Confirm Password. Click Next.
Step 8 You can change the camera’s IP settings in the below window. If you
have done this in Step 3, click Next to go to the next step.
Step 9 If you would like to set up email alerts that you can receive in the future,
enter your email information here. You can get this information from your email
service provider. You can also set this up at a later time. Click Next.
Step 10 If you would like to connect the camera wirelessly to the network, enter
the wireless information according to your wireless router’s (or access point’s)
wireless settings. You can log into the router’s (or AP’s) web configuration
pages to get the SSID and encryption details. Click Next.
Step 11 Confirm your settings at the last window. If everything is correct, click
Apply and the configuration is completed.
You can now disconnect the RJ-45 cable from the camera to access the
camera wirelessly.
Section 4
Viewing Images
Method 1 --- Access from “Web Browser”
Step 1 If you know the IP address of your network camera, you may open the
Web Browser on your computer.
Step 2 Type the IP address of your camera (the default IP is 192.168.1.240) in
the Address bar, and then press [Enter].
Step 3 Enter “admin” for both the User name and Password, and click OK.
Step 4 If it is the first time for your computer to access the Web based viewing
page, you may be prompted to install the ActiveX Control. Click on the bar at
the top of the screen and click on Install ActiveX Control.
Step 5 Click on Install. Once the installation is completed, you may be able to
view live images.
Step 6 For clearer images, you may simply rotate the camera’s lens clockwise
or counter-clockwise to adjust the focus.
Note: If you are not able to find the pictures or video clips saved by “Snapshot’
or “Manual Record” under Windows Vista, you may also need to disable
Internet Explorer’s Protected Mode: Open Internet Explorer and click Tools.
Then click Internet Options. Select the Security tab, uncheck the box for
protected mode, and click Apply. Restart Internet Explorer.
Method 2 --- Access from “SkyIPCam Utility”
Step 1 Go to Start > (All) Programs > AirLink101 > AirLink101 SkyIPCam
Utiliy, and open the Airlink101 SkyIPCam Utility.
Step 2 Select your camera from the list and click Link
Step 3 Follow Step 3 to Step 6 mentioned in Method 1.
Section 5
Technical Support
E-mail: [email protected]
Toll Free: 1-888-746-3238
Website: www.airlink101.com
*Theoretical maximum wireless signal rate based on IEEE standard 802.11g specifications. Actual
data throughput will vary. Network conditions and environmental factors, including volume of
network traffic, building materials and construction, mix of wireless products used, radio frequency
interference (e.g., cordless telephones and microwaves) as well as network overhead lower actual
data throughput rate. Specifications are subject to change without notice. All products and
trademarks are the property of their respective owners. Copyright ©2008 AirLink101®
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement