Aiwa CDC-X927M YUC Car Stereo System User Manual

OPERATING INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MODE D’EMPLOI
CDC-X927M YUC
STEREO CAR CD RECEIVER
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA
AUTOMOVIL
ENGLISH
ESPAÑOL
FRANÇAIS
OWNER’S RECORD
For your convenience, record the model number and
serial number (you will find them on the bottom side of
your set) in the space provided below. Please refer to
them when you contact your AIWA dealer in case of
difficulty.
Model No. CDC-X927M
Serial No.
8C-KC4-901-01
020131ATM-OX
PRECAUTIONS
TABLE OF CONTENTS
• Use only in a 12-volt DC negative-ground electrical
system.
• Disconnect the vehicle’s negative battery terminal
while mounting and connecting the unit.
• When replacing the fuse, be sure to use one with an
identical amperage rating. Using a fuse with a higher
amperage rating may cause serious damage to the unit.
• Do NOT attempt to disassemble the unit. Laser beams
from the optical pickup are dangerous to the eyes.
• Make sure that pins or other foreign objects do not get
inside the unit; they may cause malfunctions, or create
safety hazards such as electrical shock or laser-beam
exposure.
• When your vehicle has been parked in direct sunlight
resulting in a considerable rise in the temperature
inside, allow the unit to cool off before operating it.
• Keep the volume at a level at which you can hear
outside warning sounds (horns, sirens, etc.).
THEFT PROTECTION .............................................. 2
BASIC OPERATION, AUDIO AND CLOCK
ADJUSTMENT ..................................................... 2
RADIO OPERATION ................................................. 3
CD PLAYER OPERATION ........................................ 4
AUXILIARY EQUIPMENT ......................................... 5
OTHER FUNCTIONS ............................................... 5
CARD REMOTE CONTROL ..................................... 6
CD CHANGER OPERATION .................................... 7
TROUBLESHOOTING .............................................. 7
MAINTENANCE ........................................................ 8
SPECIFICATIONS .................................................... 8
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on circuit
different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV
technician for help.
CD Notes
• Playing a defective or dusty CD can
cause dropouts in sound.
• Hold CDs as illustrated.
• Do NOT touch the unlabeled side.
• Do NOT attach any seal, label or data
protection sheet to either side of a
disc.
• Do NOT expose a CD to direct sunlight or excessive
heat.
• Wipe a dirty CD from the center outward with a cleaning
cloth.
Never use solvents such as benzine or alcohol.
• This unit cannot play 3-inch (8 cm) CDs.
• NEVER insert a 3-inch CD contained in the adapter or
any irregularly shaped CD.
The unit may not be able to eject it, resulting in a
malfunction.
DEMO (Demonstration) mode
The unit has an extra display mode, which demonstrates
the display of the operation modes of the unit. The unit
switches to DEMO mode automatically if you turn the
unit on and leave it as it is for 5 seconds after all the
connections have been completed.
To cancel DEMO mode
1 Press and hold SRC until “CONT.” appears on the
display.
2 Press TUNE i or TUNE k until “DEMO.” appears
CAUTION
Modifications or adjustments to this product that are not
expressly approved by the manufacturer may void the
user’s right or authority to operate this product.
In addition to ordinary CDs, CD-Rs or CD-RWs can
be read by this unit. However, NEVER use a CD-R or
CD-RW that contains no data or data in the wrong
format, such as MP3 or other computer files.
1
ENGLISH
on the display.
3 Turn AUDIO CONTROL to select “DEMO. OFF”.
To resume DEMO mode, select “DEMO. ON” in step 3.
THEFT PROTECTION
Adjusting the volume
(Retractable Front Panel)
1 Turn AUDIO CONTROL.
When your car’s ignition switch is turned off, the front
panel will be retracted automatically as if there were no
car audio in the console.
When the ignition switch is set to ACC or ON position,
the front panel will appear automatically.
Muting the sound
Note
MUTE indicator flashes.
To restore volume, briefly press PWR/MUTE again.
Do not touch and put excessive pressure on the front
panel while it is rotating.
BASIC OPERATION,
AUDIO AND CLOCK
ADJUSTMENT
AUDIO CONTROL
TUNE
EJECT
VOL (volume) indication appears.
1 Press PWR/MUTE briefly.
Adjusting sound
You can select the following modes for adjusting sound
depending on the music you listen to: BASS (low
frequencies), TRE (high frequencies), BAL (left/right),
FAD (front/rear), H-BASS (high bass)*, DSSA (Drivers
Sound Stage Adjustment)** and BBE***.
* You can reinforce the bass sound.
** You can adjust sound stage and tone balance to best
serve a particular seat in the car.
*** You can enhance the clarity of high-frequency sound.
1 Press SEL repeatedly to select the mode to be
SEL
PWR/MUTE
DISP
BAND
SRC
• You can turn the unit on by pressing any button on the
front panel except z. The unit also turns on when you
press z and insert a CD.
• Press and hold PWR/MUTE until the unit turns off.
Note
Most operations described in this manual require
the unit to be turned on before starting the operation,
unless explicitly stated otherwise.
Changing the source mode
1 Press SRC.
Pressing SRC cycles through source modes in the
following order:
Notes
• Adjust the level or select an item within 5 seconds, or
the selected mode will return to previous state.
• When DSSA is activated, you cannot adjust BAL, FAD,
BASS, TRE and BBE.
• When BBE sound is activated, you cannot adjust
BASS and TRE.
Aligning the source levels
(Source Level Adjuster)
* To select another bands, press BAND to select F2,
F3, A1, A2, while “F1” is displayed.
** “DISC” does not appear on the display when there is
no CD in the unit.
***CD Changer Play mode (available when an optional
CD Changer is connected)
Volume may vary each time you change the source
mode. In this case, you can align each source mode’s
volume to almost the same level.
1 Press SRC repeatedly to select the desired mode.
2 Press DISP while pressing SEL.
“LEVEL 0” appears on the display.
3 Turn AUDIO CONTROL to adjust the level.
Note
Adjust the level within 5 seconds, or this function will be
canceled.
ENGLISH
2
ENGLISH
Turning the unit on/off
adjusted.
Pressing SEL cycles through the modes. The
selected mode’s indicator appears.
2 Turn AUDIO CONTROL to increase or decrease
the level for the selected mode (except for H-BASS,
DSSA and BBE).
In H-BASS mode, turn AUDIO CONTROL to select
1, 2, 3, or OFF.
In DSSA mode, turn AUDIO CONTROL to select L
(for the front left seat), R (for the front right seat), or
OFF.
In BBE mode, turn AUDIO CONTROL to select 1,
2, or OFF.
Restoring the factory settings
1 Press BAND repeatedly to select the desired band
1 Turn off the unit.
2 Press and hold DISP until “LEVEL --” appears on the
2 Press TUNEi (to move to higher frequencies) or
(F1, F2, F3, A1 or A2).
display.
Note
You can restore the factory settings only for VOL, BASS,
TRE, BAL, FAD, H-BASS, DSSA and BBE as well as
aligned source volume levels.
Setting the beep tone
1 Turn off the unit.
2 Press and hold SEL until “BEEP” appears on the
display.
3 Turn AUDIO CONTROL to select “ON” or “OFF”.
4 Press SEL.
The unit turns off.
TUNEk (to move to lower frequencies) to tune in to
a station.
“ST” appears on the display when an FM station is
broadcasting in stereo, and receiving conditions are
good.
Seek Tuning and Manual Tuning
• Press and hold TUNEi or TUNEk until Seek
Tuning starts.
The unit locates a station automatically (Seek
Tuning).
• Press TUNEi or TUNEk repeatedly to search for
a desired station while increasing or decreasing
the frequency step by step (Manual Tuning).
To stop Seek Tuning, press TUNEi or TUNEk
again.
Monaural mode
Setting the clock
1 Press and hold DISP until the clock indicator
When FM signals become weak, or FM reception
becomes poor, the unit automatically switches to
Monaural mode to reduce noise.
Note
flashes on the display.
2 Press TUNEi (to set hour) or TUNEk (to set
minute) and turn AUDIO CONTROL.
3 Press DISP.
Displaying the clock
When stereo sound is received, you can also press ST
and select “MONO ON” to listen in manaural mode.
To resume stereo sound receiving, press ST to “MONO
OFF”.
Local mode
1 Press DISP.
To return to the former display, press DISP again.
RADIO OPERATION
Tuning in to a station
(Seek/Manual Tuning)
Local mode allows you to tune in only to strong stations
during Seek Tuning.
1 Press LO before you start seek tuning.
“LO” appears on the display.
To return to Distant mode, press LO again.
“LO” disappears and the unit tunes in to all receivable
stations.
Using preset stations
You must preset stations before you can tune in to a
station using preset station number buttons.
TUNE
TUNE
BAND
ST
LO SRC
Stereo indicator
Band indicator*
BAND
Preset station
buttons 1 – 6
PS/A.ME
Preset station number
Local indicator
Frequency indication
* “F” means FM, and “A” means AM.
3
ENGLISH
SRC
Presetting stations automatically
CD PLAYER OPERATION
(Auto Memory)
1 Press BAND repeatedly to select the desired band
(F1, F2, F3, A1 or A2).
2 Press and hold PS/A.ME until automatic presetting
starts. “A MEM” appears on the display.
The unit automatically stores up to 6 stations for
each band.
After completion of automatic presetting, the unit
tunes in to all the stations stored on the preset
station buttons in order (Preset Scan).
To cancel automatic presetting, press PS/A.ME again.
Playing a CD
You can play CDs, CD-Rs and CD-RWs using the
procedure described below.
EJECT
INT
Checking the preset stations (Preset Scan)
RNDM
REP1
SRC
1 Press PS/A.ME briefly.
Each preset station will be tuned in for 5 seconds in
order.
To cancel Preset Scan, press PS/A.ME again or any
preset station button.
1 Press z to open the front panel.
2 Insert a CD.
The front panel will be closed automatically and
“CD” appears on the display.
CD play starts.
If a CD is already inserted, press SRC repeatedly to
select CD play mode.
In normal play, when the last track finishes, the unit
returns to the first track and continues to play.
Presetting stations manually
(Manual Memory)
1 Press BAND repeatedly to select the desired band
(F1, F2, F3, A1 or A2).
Labeled-side up
2 Press TUNEi or TUNEk to tune in to a desired
station (see “Tuning in to a station,” page 3).
3 Press and hold the desired preset station button until
the unit beeps.
Note
A newly preset station replaces the station on the same
band that was previously stored on that preset station
button.
CD indicator
Elapsed playing time
Tuning in to a preset station
1 Press BAND repeatedly to select the desired band
Track number
(F1, F2, F3, A1 or A2).
2 Press the preset station button on which the desired
station is stored.
To
Press
Eject a CD
z*
Active tuning reception control (ATRC)
Skip to the next track
t
The unit automatically suppresses FM noise caused by
vehicle movement, and maintains sound quality.
Go back to the beginning r
of the current track
Each extra press skips
backward one extra track
Locate a specific point in
a track
Press and hold r or
t until you find the
point.
* When you remove the CD, the front panel will be
closed automatically after a while.
To close the front panel manually, press z while the
front panel is open.
ENGLISH
4
1 Connect a cassette/MD/MP3 portable player or other
Notes
• When you play a CD that is already inserted, CD play
starts at the point where it stopped the previous time.
A newly inserted CD starts from the first track.
• A CD-R or CD-RW may take some time to start playing
back, but this is not a malfunction.
• If a CD-R or CD-RW with no data or incompatible data
is inserted, “ERROR03” will appear on the display.
(See the section “TROUBLESHOOTING”.) The unit
cannot play such discs.
Intro Play
You can locate a desired track by monitoring the first 10
seconds of all the tracks on a CD.
1 Press INT during CD play.
“SCAN” appears on the display.
2 Press INT again when the desired track is played.
The unit returns to normal CD play.
equipment via the unit’s AUX IN jack (3.5 mm dia.).
2 Press SRC repeatedly until “AUX IN” appears on the
display.
Note
When a connecting cord is plugged into the AUX IN jack,
you cannot insert or eject a CD even if you press z. Be
sure to disconnect the cord before inserting or ejecting
the CD. Likewise, be sure to disconnect it before you
turn off the ignition switch, otherwise the front panel
won’t be retracted.
OTHER FUNCTIONS
AUDIO CONTROL
TUNE
One Track Repeat Play
You can play a track repeatedly.
1 Press REP1 during CD play.
“REP1” appears on the display.
To cancel One Track Repeat Play, press REP1 again.
SEL
SRC
Random Play
Changing the display contrast
You can play all the tracks in random order.
1 Press RNDM during CD play.
“RANDOM” appears on the display.
To cancel Random Play, press RNDM again.
1 Press and hold SRC until “CONT.” appears on the
display.
2 Turn AUDIO CONTROL to adjust the contrast.
Note
During Random Play, pressing r allows you to skip
only to the beginning of the current track, not to the
previous track.
AUXILIARY EQUIPMENT
Listening to a cassette/MD/MP3
portable player or other equipment
You can listen to music through equipment connected to
the unit. Refer to the operating instructions for the
corresponding equipment for more detailed information.
Be sure to remove any loaded CD to prevent possible
damage to the unit before connecting the equipment.
Changing the key illumination color
You can choose blue or red as the key illumination color.
1 Press and hold SRC until “CONT.” appears on the
display.
2 Press TUNEi or TUNEk until “ILL” appears on the
display.
3 Turn AUDIO CONTROL to select 1 (for blue) or 2
(for red).
Setting the dimmer of the display
1 Press and hold SEL until “DIMMER” appears on the
display.
2 Turn AUDIO CONTROL to select 0 (bright) or
1 (dimmed).
SRC
AUX IN jack
5 ENGLISH
CARD REMOTE
CONTROL
Names of parts
Replacing the battery
1 Insert the tip of a pointed object A into the hole B
and pull out the battery holder to remove the lithium
battery (CR2025).
Remote control (back)
BAND
TAPE
CD
CD-CH
SKIP
REW
FF
TUNING / DISC
UP
DOWN
Battery holder
VOLUME
2 Install a new lithium battery (CR2025) with the )
side facing up in the battery holder.
1 BAND button
2 TAPE button (This button is not available with this
unit.)
3 CD button
4 CD-CH button (CD changer only)
5 SKIP f/REW button
6 SKIP g/FF button
7 PS (preset) button
8 TUNING/DISC UP/DOWN buttons
9 VOLUME +/- buttons
3 Push the battery holder into the unit until it clicks.
Preparations
A lithium battery is installed in the remote control at the
factory.
Before you use the remote control, be sure to remove
the insulating sheet by simply pulling it out.
Remote control (back)
CAUTIONS
• Keep the lithium battery out of the reach of children. If
swallowed, consult a doctor immediately.
• To prevent a short circuit, never pinch the battery with
pliers, etc.
Insulating sheet
ENGLISH
6
CD CHANGER OPERATION
Playing a CD
You can play CDs from a connected AIWA CD Changer.
For detailed information on installing a CD Changer,
refer to the Installation and Connection manual supplied
with the CD Changer.
RNDM
One Disc Repeat Play
You can play all tracks on a disc repeatedly.
1 Press REP during CD Changer play.
“REP” appears on the display.
To cancel Repeat Play, press REP again.
One Track Repeat Play
You can play a track repeatedly.
1 Press REP1 during CD Changer play.
“REP1” appears on the display.
To cancel Repeat Play, press REP1 again.
One Disc Random Play
INT
DISC
REP1
REP
SRC
You can play all the tracks on a disc in random order.
1 Press RNDM during CD Changer play.
“RANDOM” appears on the display.
To cancel Random Play, press RNDM again.
Note
1 Press SRC repeatedly to display “CD-CH.”
The CD Changer play starts.
CD Changer indicator
During Random Play, pressing r allows you to skip
only to the beginning of the current track, not to the
previous track.
Track number
TROUBLESHOOTING
Error code
CD number
To
Press
Skip to the next track
t
Skip back to the beginning of r
the current track or to the
previous track
Advance rapidly to locate a
desired point
Press and hold t,
then release it at the
desired point
Reverse rapidly to locate a
desired point
Press and hold r,
then release it at the
desired point
Start CD Changer play from DISCN
the first track on the next disc
Start CD Changer play from DISCM
the first track on the previous
disc
Intro Play
You can locate a desired track by monitoring the first 10
seconds of all the tracks on the CDs in the disc magazine.
1 Press INT during CD Changer play.
“SCAN” appears on the display.
2 Press INT again when the desired track is played.
The unit returns to normal CD play.
7 ENGLISH
In the following cases the corresponding error code
indication appears. Follow the suggestions below to
solve such problems. If the error code indication does
not disappear, consult an AIWA service center.
ERROR01 The disc magazine is not properly inserted
in the CD Changer. Reinsert the magazine.
Refer to the instruction manual for the CD
Changer.
ERROR02 No CDs are loaded in the disc magazine.
Insert CDs properly. Refer to the instruction
manual for the CD Changer.
ERROR03 Focus error. Check that the CD is loaded
properly (right side up, etc.), and the CD
contains valid data.
ERROR04 Problem with the CD Changer. Reset the
unit by pressing the reset button. If this does
not solve the problem, consult an AIWA
service center.
Reset button
GENERAL
If a CD does not operate properly, press the reset button
with a pointed object such as a pencil, etc. Note that all
your settings will be erased if this button is pressed.
Power-Supply Voltage: 14.4 V (11 to 16 V
allowable), DC, negative ground
Load Impedance: 4 Ω
Tone Control: Bass ± 10 dB at 100 Hz, Treble ±
10 dB at 10 kHz
Preamp Output Voltage (load impedance): 2.2 V
(10 kΩ)
Installed size: 182 (W) × 53 (H) × 155 (D) mm
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)
Reset button
MAINTENANCE
Cleaning the front panel
Wipe the surface with a soft, dry cloth.
CARD REMOTE CONTROL
Dimensions: approx. 33 (W) × 85 (H) × 7.5 (D) mm
(1 5/16 (W) × 3 3/8 (H) × 5/16 (D) inches)
Weight: approx. 20 g (0.7 oz.) (including battery)
• Specifications and external appearance are subject to
change without notice due to product improvement.
REAR PANEL
SPECIFICATIONS
RADIO SECTION
(FM)
Frequency Range: 87.5 MHz – 108 MHz
Usable Sensitivity: 12.7 dBf
50 dB Quieting Sensitivity: 17.2 dBf
IF Rejection: 100 dB
Frequency Response: 30 Hz – 15,000 Hz
S/N Ratio: 70 dB
Stereo Separation: 35 dB at 1 kHz
Alternate Channel Selectivity: 90 dB
Capture Ratio: 3 dB
For details, refer to the separate “INSTALLATION AND
CONNECTIONS”.
The word “BBE” and the “BBE symbol” are trademarks
of BBE Sound,Inc.
Under licence from BBE Sound,Inc.
(AM)
Frequency Range: 530 kHz – 1,710 kHz
Usable Sensitivity: 30 µV (30 dB)
CD SECTION
Frequency Response: 17 Hz – 20 kHz +0/–3 dB
Dynamic Range: More than 92 dB
Channel Separation: More than 60 dB
S/N Ratio: More than 90 dB
Wow/Flutter: Unmeasurable
AUDIO SECTION
Max. Power Output: 45 W × 4 channels
AUX IN input
Input sensitivity (load impedance) AUX IN: 300 mV
(10 kΩ)
ENGLISH
8
Printed in Indonesia