Specifications | Aiwa LCX-357 Stereo System User Manual

TABLE OF CONTENTS
2
IMPORTANT INFORMATION
3-4
IMPORTANT SAFETY INSTRUCTIONS
5
SUPPLIED ACCESSORIES
6-7
REMOTE CONTROL
FUNCTIONAL OVERVIEW
8
CONNECTIONS
9
10
BASIC OPERATIONS
WATCHING TV
11-12
MENU ADJUSTMENT
13-18
BASIC OPERATIONS DVD
19-24
PLAY DISCS IN VARIOUS WAYS
24-29
MENU SETTING DVD
30-34
35
KODAK PICTURE CD PLAYBACK
36-37
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
38
WARRANTY PAGE
39
page1
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated ’’dangerous
voltage’’ within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the
presence of important operation and maintenance (servicing) instructions
in the literature accompanying the product.
FCC RF INTERFERENCE STATEMENT
NOTE: This equipment has been tested and found to comply with the limit for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does not cause harmful interference to radio or television reception which
can be determined by turning the equipment off and on, the user is encourage to try to
correct the interference by one or more of the following measure.
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Correct the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio, TV technical for help.
● Only shielded interface cable should be used.
page2
IMPORTANT SAFETY PRECAUTIONS
The present set has been designed and manufactured to assure personal safety. Improper use
can result in electric shock or fire hazard. The safeguards incorporated in the present unit will
protect you if you observe the following procedures in installing, using and servicing. The present
unit is fully transistorized and does not contain any element that can be repaired by the user.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Repair - If any of the following conditions occurs, unplug the AC cord from the AC outlet, and
request a qualified service person to perform repairs.
a) When the AC cord or plug is damaged.
b) When a liquid was spilled on the product or when objects have fallen into the product.
c) When the product has been exposed to rain or water.
page3
IMPORTANT SAFETY PRECAUTIONS
d) When the product does not operate properly as described in the operating instructions. Do
not touch the controls other than those described in the operating instructions. Improper
adjustment of controls not described in the instructions can cause damage, which often
requires extensive adjustment work by a qualified technician.
e) When the product has been dropped or damaged.
f) When the product displays an abnormal condition. Any noticeable abnormality in the product
indicates that the product needs servicing.
16. Replacement parts - In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same
characteristics and performance as the original parts. Use of unauthorized parts can result in
fire, electric shock and/or other danger.
17. The LCD panel used in this product is made of glass. Therefore, it can be broken when the
product is dropped or gets shock. Be careful not to be injured by glass pieces in case the
panel is broken.
18. The LCD panel is a product of very high technology with 2,949,120 thin film transistors, giving
you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a
fixed blue, green or red point. Please note that this does not affect your product’s performance.
page4
SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the product.
Power adapter
Remote control
Owner′
s Manual
AAA batteries
Warranty card
Quick setup guide
page5
REMOTE CONTROL
INSERTING BATTERIES INTO THE REMOTE CONTROL
Insert supplied batteries via the battery compartment on the back of the remote control.
Make sure polarity matches the (+) and (-) marks inside the compartment.
-
+
+
-
USING THE REMOTE CONTROL UNIT
●
●
●
Use the remote control by pointing it towards the remote
sensor on the TV. Objects between the remote control and
the sensor may disrupt operation.
Effective range is 20 feet but is dependant on what your
viewing angle is.
Range can also be affected by direct sunlight on the TV’s
sensor.
CAUTIONS REGARDING REMOTE CONTROL UNIT
●
●
Do not expose remote to liquids, direct sunlight or shock.
The remote control unit may not work properly if the remote sensor window of the Display is
under direct sunlight or strong lighting. In such case, change the angle of the lighting or Display,
or operate the remote control unit closer to the remote sensor window.
page6
REMOTE CONTROL
POWER
MPX
Use to turn the unit on and off.
Number Buttons
Use to select the sound multiplex
mode. (See page 16.)
Use to set the channel and to enter
DVD chapter numbers.
OSD
CAPTION
Use to bring up the DVD OnScreen-Display.
Use to select close caption mode.
VOLUME+/-
OPEN( )
Use to adjust the volume.
Use to eject the disc being played
in the disc slot, the main unit must
be set to DVD status.
LAST
Press to return to the previous
channel in normal viewing mode.
AUTO
TV/DVD/AUX/PC
Auto adjustment for PC signals.
Use to bring up the AV signal source
selection screen and use the /
buttons to select between: TV, DVD,
AV1-S-Video, AV2-Video, AV3Component, PC-Analog(VGA), PCDigital(DVI), and press the OK
button to confirm.
MUTE
Mute the sound.
CH+/Use to skip to the previous/next
channel.
Cursor Buttons
Use to navigate in menus.
TV MENU
OK
Use to confirm your selections.
Use to bring up TV menu; and
exits TV menu by pressing again.
DVD TITLE
DVD MENU
Use to bring up the DVD title menu.
PLAY
Use to bring up the DVD root
menu.
Use to begin the DVD playback.
STOP
PAUSE
Use to stop the DVD playback.
Use to pause the DVD playback.
FF/FR
PREV/NEXT
Use to play DVD fast forward/
backward.
Use to skip to the previous/next
chapter.
RETURN
ZOOM
Use to zoom the DVD playback
picture.
Return to the previous menu
screen.
SLOW
SETUP
Use to slow the DVD playback speed.
Use to bring up DVD setup menu.
P. MODE
WIDE
Use to shift DVD play mode.
REMAIN
In DVD mode, use to set TV
display mode.
Use to display the time of the DVD
playback.
ANGLE
A. MODE
Use to shift DVD viewing angle.
Use to shift the DVD playback audio
mode.
REPEAT
AUDIO
SUBTITLE
Use to shift DVD audio language.
Use to shift DVD subtitle language.
Use to repeat the DVD playback.
page7
FUNCTIONAL OVERVIEW
FRONT VIEW
8
4
PLAY
5
6
TV/DVD/AUX/PC
CH
7
CH
VOL
VOL
9
Slot-load
DVD Player
PAUSE
10
PREV
11
NEXT
12
EJECT
13
3 2 1
1) REMOTE SENSOR
2) POWER ON INDICATOR
3) STANDBY INDICATOR
4) POWER BUTTON: Use to turn the unit on and off.
5) TV/DVD/AUX/PC: Use to select the AV signal source among: TV, DVD,AV1-S-Video, AV2Video, AV3-Component,PC-Analog(VGA), PC-Digital(DVI) and use the OK button to confirm.
6) CH+/-: To skip to the previous/next channel.
7) VOLUME+/-: Use to adjust the volume.
8) DISC SLOT: Insert a DVD or CD disc to play under DVD status.
9) PLAY BUTTON: Use to begin the DVD playback.
10) PAUSE BUTTON: Use to pause the DVD playback.
11) PREV: Use to skip to the previous chapter.
12) NEXT: Use to skip to the next chapter.
13) EJECT BUTTON: Use to eject the disc being played in the disc slot.
REAR VIEW
AUDIO
L
R
AV OUT
1
L
VIDEO
AUDIO
S-VIDEO
R
2
AV 1 I N
VIDEO
L
AV 2 I N
AUDIO
CR / PR
3
R
CB / PB
L
AUDIO
Y
4
R
AV 3 I N
DVI
DC
24V 6A
PC INPUT
VGA
PC INPUT
DC INPUT
10
9
8
OPTICAL
AUDIO
DVD OUTPUT
DVI/VGA INPUT
7 6
5
page8
1) AV OUT (Composite Video and Audio
Out)
2) AV1 IN (S-Video and Audio In)
3) AV2 IN ( Composite Video and Audio In)
4) AV3 IN (Component Video(Y、PB/CB、
PR/CR) and Audio In)
5) Antenna In
6) AUDIO (VGA/DVI Input)
7) OPTICAL (DVD Output)
8) VGA INPUT
9) DVI (Digital Video Input)
10) DC INPUT
CONNECTIONS
2g
AUDIO
R
L
AV OUT
L
VIDEO
AUDIO
S-VIDEO
R
AV 1 I N
L
VIDEO
AV 2 I N
AUDIO
CR / PR
R
L
CB / PB
AUDIO
Y
R
AV 3 I N
DVI
DC
24V 6A
PC INPUT
DC INPUT
VGA
PC INPUT
OPTICAL
AUDIO
DVD OUTPUT
DVI/VGA INPUT
2f
1. CONNECT TO POWER
a. Connect the mini plug of the AC power
adapter to DC IN jack on the back of the
26MD255V.
b. Connect the power plug of the AC power
adapter to the power socket.
2. SYSTEM CONNECTIONS
a. Using the antenna input: Connect the
antenna terminal from an antenna or cable
/satellite receiver to the antenna input
terminal on the 26MD255V; use the
TV/DVD/AUX/PC button and the /
buttons to set the 26MD255V’s signal source
to "TV".
b. Using the AV2 RCA Video/Audio input:
Connect compatible AV equipment to the
26MD255V through the AV2 IN jacks on
26MD255V (Composite Video and Audio
input jacks); use the TV/DVD/AUX/PC
button and the / buttons to set the
26MD255V’s signal source to "AV2-Video".
c. Using the AV1 S-Video and RCA Audio
input: Connect AV equipment to the
26MD255V through the AV1 IN jacks on
26MD255V (S-Video and Audio input jacks);
use the TV/DVD/AUX/PC button and the /
buttons to set the 26MD255V s signal
source to AV1-S-Video .
d. Using the AV3 Component input: The AV3
input may be used for Progressive scan or
HDTV inputs; use the TV/DVD/AUX/PC
button and the / buttons to set the
26MD255V’s signal source to "AV3-Component".
e. Using the VGA connector: Connect a PC
computer to the 26MD255V through the VGA
socket on 26MD255V. The Mini-plugged next
to the VGA input is for audio associated with
this type of signal. Use the TV/DVD/AUX/PC
button and the / buttons to set the
26MD255V s signal source to
PC-Analog(VGA) .
26MD255V monitor s native resolution for
computer use is 1280x768.
f. Using the DVI connector: Connect a PC
computer to the 26MD255V through the DVI
socket on 26MD255V. The Mini-plugged is for
audio associated with this type of signal.
Use the TV/DVD/AUX/PC button and the /
buttons to set the 26MD255V s signal source
to PC-Digital(DVI) .
g. Using the AV out, RCA Video/Audio
output: Connect the 26MD255V to another
TV Monitor through the AV OUT jacks on
26MD255V (Composite Video and Audio
output jacks); now you can use the TV
Monitor as an external monitor. Signals from
the Antenna, AV1, AV2 and Internal DVD
player will be available at this point.
page9
BASIC OPERATIONS
TURNING OFF THE POWER
POWER
TV/DVD/AUX/PC
TV/DVD/
AUX/PC
CH
CH
VOL
1. Press POWER on the remote control, the
image on the screen disappears and the
STANDBY indicator lights up red.
NOTE: Small amounts of electric power is still
consumed even when the power is
turned off.
VOL
TV/AV MODE SELECTION
By pressing the TV/DVD/AUX/PC on the TV
set and confirming by the OK button, you can
change the mode as follows:
TV
DVD
POWER
AV1-S-Video
AV2-Video
AV3-Component
PC-Digital(DVI)
TV/DVD/
AUX/PC
TURNING ON THE POWER
1. Press POWER button on the front panel to
turn on the TV set. The POWER indicator
lights up green.
2. If the STANDBY indicator still lights up red,
press POWER on the remote control to turn
the TV set on.
page10
PC-Analog(VGA)
WATCHING TV
TURNING ON THE POWER
1. Press POWER button on the front panel to
turn on the TV set. The POWER indicator
lights up green.
2. If the STANDBY indicator still lights up red,
press POWER on the remote control to turn
the TV set on.
CH+/-
TURNING OFF THE POWER
1. Press POWER on the remote control, the
image on the screen disappears and the
STANDBY indicator lights up red.
NOTE: Weak electric power is still consumed
even when the power is turned off.
SIMPLE BUTTON OPERATIONS
FOR CHANGING CHANNELS
You can change channels in several ways.
Using CH+/- on the remote unit
CH+/-
TV/DVD/
AUX/PC
CH
CH
VOL
1. Press CH+ to increase channel number.
2. Press CH- to decrease channel number.
NOTE: CH+/- on the TV set operates the
same as CH+/- on the remote unit.
VOL
page11
WATCHING TV
Using number buttons on the remote unit
SIMPLE BUTTON OPERATION
FOR CHANGING VOLUME/SOUND
Changing the volume
You can change the volume on the front panel
or on the remote control unit.
NUMBER
BUTTONS
Select the channels directly by pressing the
number buttons.
EXAMPLE:
To select a 1-digit channel (e.g. channel 2):
● Press 2 .
To select a 2-digit channel (e.g. channel 12):
● Press 1 ,followed by 2 .
USING LAST ON THE REMOTE
UNIT
VOLUME+/-
1. Press VOL+ to increase the volume.
2. Press VOL- to decrease the volume.
Using MUTE on the remote control
Press MUTE to mute the current sound
output.
LAST
MUTE
Press LAST to switch the currently tuned
channel to the previous tuned channel.
Press LAST again to switch back to the
currently tuned channel.
1. Press MUTE . ’’
’’ will display on the
screen.
2. Press MUTE again to cancel the mute.
page12
MENU ADJUSTMENT
TV TUNER ADJUSTMENT
Press TV MENU to bring up the TV menu
screen.
Press
/
to select "Settings" and press
to
enter into the items below ’’Settings’’.
NOTE: Only when in TV status, there is "TV
Tuner"option below "Settings".
Make sure press TV MENU to exit TV
menu screen before other operatings.
Cable
1. Press TV MENU to bring up the TV menu
screen.
2. Press
/
to select "Settings" and press
to select "TV Tuner".
3. Press
to enter "TV Tuner" menu.
setting
on
0
down for TV channel settings
4. Press / to select "Cable".
5. Press / to change cable on and off;
press OK to return; press TV MENU to
exit.
Automatic channel search
Channel auto search finds and memorizes all
channels viewable in your area.
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select "Settings" and press
to select "TV Tuner".
3. Press to enter "TV Tuner" menu.
4. Press / to select "Auto Search".
5. Press to begin the searching. Wait until
the searching ends.
NOTE: The illustrations and on-screen displays
in this manual are for explanation
purposes and may vary from the actual
operations.
Auto Fine Tune
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select "Settings" and press
to select "TV Tuner".
3. Press to enter "TV Tuner" menu.
4. Press / to select "Auto Fine Tune".
5. Press / to select between on and off ;
press OK to return; press TV MENU to
exit.
Fine tune
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select "Settings" and press
to select "TV Tuner".
3. Press to enter "TV Tuner" menu.
4. Press
/ to select "Fine Tune".
5. Press to enter "Fine Tune" screen.
6. Press / to tune for a better picture and
sound; press OK to return; press TV MENU
to exit.
Channel skip
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select "Settings" and press
to select "TV Tuner".
3. Press to enter "TV Tuner" menu.
4. Press / to select "Skip".
5. Press / to select between "Skip" and
"Add"; press OK to return; press TV MENU
to exit.
page13
MENU ADJUSTMENT
CONTENT BLOCKING
Password
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select "Settings" and press
to select "Content Blocking".
3. Press to enter "Content Blocking
(Password)" menu.
Password
0 0 0 0 0 0
0 0 0 0 0 0
7. Press to select "Change" and press to
change the password.
8. Press / to select digit and press / to
change the selected digit.
9. Press to select "OK" and press OK to
confirm your change.
10. Press to select "Clear" and press
to
clear the password; press OK to return;
press TV MENU to exit.
NOTE:The preset password is 071100.
_Enter 071100 , there will be
ERROR displayed on the screen.
_Enter 071100 again, the menu for
changing password appears.
4. Press to select "Enter" and press to
enter the password.
5. Press / to select digit and press /
to change the selected digit.
6. Press to select "OK" and press OK to
check the password. Then there will be
"Change" and "Clear" under "Enter".
page14
MENU ADJUSTMENT
PICTURE ADJUSTMENT
AUDIO ADJUSTMENT
Press TV MENU to bring up the TV menu
screen.
Press / to select ’’Picture’’ and press to
enter into below items.
Press TV MENU to bring up the TV menu
screen.
Press / to select ’’Audio’’ and press to
enter into below items.
16
16
16
9
16
16
0
5
Brightness
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Picture’’.
3. Press / to move to ’’Brightness’’.
4. Press / to adjust the picture brightness;
press OK to return; press TV MENU to
exit.
Contrast
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Picture’’.
3. Press
/ to move to ’’Contrast’’.
4. Press / to adjust the picture contrast;
press OK to return; press TV MENU to
exit.
Color
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Picture’’.
3. Press / to move to ’’Color’’.
4. Press / to adjust the picture color; press
OK to return; press TV MENU to exit.
Sharpness
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Picture’’.
3. Press / to move to ’’Sharpness’’.
4. Press / to adjust the picture sharpness;
press OK to return; press TV MENU to
exit.
NOTE: In DVD status, there is no "Sharpness";
there is "Phase".
▲
equalizer
Volume
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Audio’’.
3. Press / to move to ’’Volume’’.
4. Press / to adjust the volume; press OK
to return; press TV MENU to exit.
Bass
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Audio’’.
3. Press / to move to ’’Bass’’.
4. Press / to adjust the bass weaker or
stronger; press OK to return; press
TV MENU to exit.
Treble
To stress high frequency sound
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Audio’’.
3. Press / to move to ’’Treble’’.
4. Press / to adjust the treble weaker or
stronger; press OK to return; press
TV MENU to exit.
page15
MENU ADJUSTMENT
WINDOW ADJUSTMENT
AUDIO ADJUSTMENT
(CONTINUED)
PC mode input format
Balance
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Audio’’.
3. Press / to move to ’’Balance’’.
4. Press / to adjust audio output between
left and right speakers; press OK to return;
press TV MENU to exit.
MPX
This function is to select a MPX mode.
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Audio’’.
3. Press / to move to ’’MPX’’.
4. Press / to select a MPX mode; press
OK to return; press TV MENU to exit.
NOTE: 1. You can also use the MPX button
on the remote control to select a
MPX mode.
2. Only when in TV status, there is
MPX option.
In case of inputting the PC signal other than
above signals, ’’OUT OF RANGE’’ will display.
Equalizer
1. Press / to select "Equalizer" in "Audio"
menu.
2. Press to enter "Equalizer" menu to adjust.
Press TV MENU to bring up the TV menu
screen.
Press / to select ’’Window’’ and press
to
enter into below items.
Resolution
Freq. (Hz)
VGA
640×480
640×480
640×480
60
72
75
SVGA
800×600
800×600
800×600
60
75
72
XGA
1024×768
1024×768
1024×768
60
70
75
WXGA
1280×768
60
SXGA
1280×1024
60
Equalizer
display mode
16
16
Change equalizer character
3. Press OK to exit and return to "Audio"
menu.
4. Press TV MENU to exit.
page16
MENU ADJUSTMENT
OPTIONS ADJUSTMENT
WINDOW ADJUSTMENT
(CONTINUED)
Display Mode
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Window’’.
3. Press / to move to ’’Display Mode’’.
4. Press / to select a Display mode; press
OK to return; press TV MENU to exit.
Press TV MENU to bring up the TV menu
screen.
Press / to select ’’Options’’ and press to
enter into below items.
H-Position
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Window’’.
3. Press / to move to ’’H-Position’’.
4. Press / to adjust the horizontal position
of displayed image; press OK to return;
press TV MENU to exit.
V-Position
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Window’’.
3. Press / to move to ’’V-Position’’.
4. Press / to adjust the vertical position of
displayed image; press OK to return; press
TV MENU to exit.
NOTE: In TV, VIDEO, S-VIDEO and
COMPONENT Status, there is only
Display Mode option.
Language
Color Temperature
English
Normal
Language
It is used to set the menu language between :
English, French and Spanish.
1. Press / to select "Language " in "Option"
menu.
2. Press / to adjust the language between :
English, French and Spanish.
3. Press TV MENU to exit.
Freeze
It is used to freeze the image.
1. Press / to select "Freeze" in "Options"
menu.
2. Press / to select ON or OFF in
Freeze .
● ON: Freeze the image being played.
● OFF: Turn off Freeze , the image continue
playing.
3. Press TV MENU to exit.
page17
MENU ADJUSTMENT
OPTIONS ADJUSTMENT
(CONTINUED)
Sleep Time
Picture Settings Reset
It is used to auto shift the time of standby status
and the time remaining will be displayed .
1. Press / to select "Sleep Time "in
"Options" menu.
2. Press / to adjust the time of "Sleep Time" :
1. Press TV MENU to bring up the TV menu
screen.
2. Press / to select ’’Options’’.
3. Press / to move to ’’Picture Settings
Reset’’.
4. Press to reset all settings to factory
setting.
10min
0 min
20min
30min
240min
60min
180min
90min
120min
3. When you have set the "Sleep Time " , the
count down will be applied automatically ,
and the time remaining displays the remain
time .
If you set the "Sleep Time " at "10 minutes
…… or 240 minutes " , "Time Remaining "
displays :
Sleep Time
120minutes
Time remaining
120
minutes
4. If you want to cancel the " Sleep Time " , you
can set the " Sleep Time " on " 0 minutes" .
5. Press TV MENU to exit.
CC Mode
1. Press / to select "CC Mode " in "Option"
menu.
2. Press / to select a CC Mode.
3. Press TV MENU to exit.
Color Temperature
It is used to adjust the Color Temperature.
1. Press / to select "Color Temperature " in
"Option" menu.
2. Press / to adjust the color temperature
between: Normal, Warm and Cool.
3. Press TV MENU to exit.
NOTE: In DVD, PC status, there is no
Freeze , CC Mode option.
In AV3-COMPONENT status, there is
no CC Mode option.
page18
BASIC OPERATIONS (FOR DVD PLAYER)
Play Discs
DVD
DVD
Pause
、 CD
、 CD
Press
1. Press POWER to turn on the unit.
2. P r e s s t h e T V / D V D / A U X / P C
button on the remote control to
b r i n g u p t h e AV s i g n a l s o u r c e
selection screen and use the /
buttons to select "DVD", press the
OK button to confirm.
3. I n s e r t a d i s c i n t o t h e d i s c s l o t ,
with the label side facing to
yourself.
4. The unit begins to read the disc.
5. Press
(PLAY) to play the disc.
PAUSE
DVD
●
To pause playback of a DVD while it is
playing, press
.The unit enters step play
status. Each time you press
, the
picture advances one frame.
AFTER STEP 4 IS FINISHED:
If playing a DVD, the TV screen shows DVD
menu or title menu.
If playing a CD, press
(PLAY), and the unit
plays the disc according to the track
numbers.
5. Stop playback.
Press ■ .
●
CD
●
●
Press
to make playback pause.
Press
(PLAY)to resume playback.
OSD
DVD
、 CD
OSD
6. Press the button on the remote control to
remove the disc and turn off the unit.
●
You have to push "■" button twice to stop
playback of a DVD disc.
The On-Screen Display (OSD) contains many
playback features.To see the Display, press the
OSD button on the remote while a disc is
playing. The picture being played will be
zoomed out to the top of the screen. The
Display appears under the zoomed picture.
Use the or
buttons on the remote to move
through the different playback features in the
Display.
When a playback feature is highlighted, press
the (PLAY) button and the text box by the right
side of it will be highlight.Use the or buttons
on the remote to move through the choices
displayed in the text box.
page19
BASIC OPERATIONS (FOR DVD PLAYER)
Remember, you can only access the Display
3. Press the
when you’re playing a disc. Also, the Display
(PLAY) button, the text box by
the right side is now highlighted.
features are only available if the disc was
4. Use the number buttons on the remote to
created with that particular feature.
enter a chapter number that you want to
The invalid symbol "
play.
" appears on the screen
when you press a button that doesn’t have any
Notes: The chapter feature won’t work if the
function. If one of the playback features is
disc isn’t formatted with separate
"grayed out ",that Display feature isn’t available
chapters. You can also advance to the
for the disc you’re playing.
next chapter by pressing
To make the Display disappear from the
remote and go to the preceding
screen, press OSD on the remote.
chapter by pressing
If the disc was created with different language
DVD discs have the following playback
tracks (recorded in different languages), you
features:Title, Chapter, Audio, Subtitle, Angle,
can use the Display to temporarily change the
TT (Title) Time, CH (Chapter) Time, Repeat
DVD player’s Audio Language setting.
and Time Display.
1. While the disc is playing, press OSD on
■ Select a Title
the remote to bring up the Display.
Some discs contain more than one title. Each
2. Press the
title is divided into chapters. To select a title:
3. Press the
the remote to bring up the Display.
buttons to highlight the
(PLAY) button, the audio
languages appear on the screen.
2. If the Title icon on the Display isn’t
or
or
Audio icon.
1. While the disc is playing, press OSD on
4. Press the
buttons to
or
buttons to move through
the audio languages that are available on
highlight it.
3. Press the
on the remote.
■ Changing the Audio Language
WHEN PLAYING DVD
highlighted, use the
on the
the disc.Press the
(PLAY) button, the text box by
(PLAY) button when the
audio language you want to use is highlighted.
the right side is now highlighted.
5. To make the Display disappear, press the
4. Use the number buttons on the remote to
OSD button on the remote.
enter a title number that you want to play.
Note: The language feature only works if the
Note: Some discs only have one title.
disc was created with multiple audio tracks.
■ Select a Chapter
When you choose an audio language from the
Because DVD discs use digital technology, a
Display, you only override the audio language
title can be divided into chapters (similar to
setting in the DVD player’s main menu
tracks on a CD). You can skip to a specific
temporarily.
chapter by using the Chapter feature in the
The audio language can also the changed
Display.
through the DVD player menu.
1. While the disc is playing, press OSD on
■ Selecting the Subtitle Language
the remote to bring up the Display.
2. Press the or buttons to highlight the
Chapter icon.
If the disc was created with subtitles, you can
use the Display to change the Subtitle
language.
page20
BASIC OPERATIONS (FOR DVD PLAYER)
1. While the disc is playing, press OSD on
1. While the disc is playing, press OSD on
the remote to bring up the Display.
the remote to bring up the Display.
2. Press the
or
2. Press the
buttons to highlight the
3. Press the
(PLAY) button, the subtitle
or
4. Use the number buttons to enter an angle
buttons to move through
number that you want to play.
the subtitle languages that are available on
the disc.Press the
(PLAY) button, the text box by
the right side is now highlighted.
languages appear.
4. Press the
buttons to highlight "TT
(Tile) Time" .
"Subtitle".
3. Press the
or
■ Setting Chapter Time
(PLAY) button when the
You can skip to a specific chapter time by using
subtitle language you want to use is highlighted.
the Chapter Time feature in the Display.
5. To make the Display disappear, press the
1. While the disc is playing, press OSD on
OSD button on the remote.
the remote to bring up the Display.
Notes: Changing the subtitle language with the
2. Press the
Display will only affect the disc currently being
or
buttons to highlight "CH
(Chapter) Time" .
played. When the disc is removed or the player
3. Press the
is turned off, the subtitle language will revert to
(PLAY) button, the text box by
the right side is now highlighted.
the language setting specified through the DVD
4. Use the number buttons to enter an angle
number that you want to play.
player main menu.
The subtitle language can also be changed
■ Using the Repeat Feature
through the DVD player menu.
The default mode for the Repeat feature is off.
■ Changing the Camera Angle
There are three Repeat options:
All - repeats the disc that is playing
Title - repeats the title that is playing
Chapter - repeats the chapter that is playing
To Use Repeat:
●
Some discs contain multiple angles of a
●
particular scene or sequence. When multiple
●
angles are available, to change the camera
angle:
1. While the disc is playing, press OSD on
1. While the disc is playing, press OSD on
the remote to bring up the Display.
the remote to bring up the Display.
2. Press the
or
3. Press the
(PLAY) button, the text box by
2. Press the
buttons to highlight "Angle".
or
buttons to highlight
"Repeat".
3. Press the
(PLAY) button, the repeat
options appear.
the right side is now highlighted.
4. Press the
4. Use the number buttons to enter an angle
or
buttons to move through
the repeat options. Press the
number that you want to play.
(PLAY)
button when the repeat option you want to
5. To make the Display disappear, press the
use is highlighted.
OSD button on the remote.
5. The selected repeat option will loop
■ Setting Title Time
repeatedly until you turn Repeat off.
You can skip to a specific title time by using the
Title Time feature in the Display.
page21
BASIC OPERATIONS (FOR DVD PLAYER)
■ Setting Track Time
You can skipo to a specific track time by using the
Track
Time feature in the Display.
1. While the disc is playing, press OSD on
the remote to bring up the Display.
2. Press the
or
buttons to highlight
"Track Time" , while a disc is playing.
3. Press the
(PLAY) button, the text box by
the right side is now highlighted.
4. Use the number buttons on the remote to
enter a track time that you want to play.
How to Cancel Repeat:
There are three ways to cancel Repeat:
Press STOP twice.
Go to Repeat icon in the Display and select
Off.
Eject the disc.
■ Shifting the Displayed Time
Using the Time Display feature in the Display,
you can shift the time displayed on the screen,
between: Title Elapsed Time, Title Remain Time,
Chapter Elapsed Time, and Chapter Remain
Time.
1. While the disc is playing, press OSD on
the remote to bring upo the Display.
2. Press the or buttons to highlight "Time
Disp".
3. Press the
(PLAY) button, the time options
appear.
4. Press the or buttons to move through the
time options. Press the (PLAY) button when
the option you want to use is highlighted.
5. To make the Display disappear, press the
OSD button on the remote.
●
●
●
■ Using the Repeat Feature
The default mode for the Repeat feature is off.
There are two Repeat options for CDs:
●
All - repeats the disc that is playing
Track - repeats the track that is playing
To use Repeat:
1. While the disc is playing, press OSD on
the remote to bring up the Display.
2. Press the
or
buttons to highlight
"Repeat" , while a disc is playing.
3. Press the
(PLAY) button, the repeat
options appears.
4. Press the
or
buttons to move through
the repeat options. Press the
(PLAY)
button when the repeat option you want to
use is highlighted.
5. The selected repeat option will loop
repeatedly until you turn Repeat off.
■ Shifting the Displayed Time
Using the Time Display feature in the Display,
you can shift the time displayed on the screen,
between: Single (Track) Elapsed Time, Single
(Track) Remain Time, Total (Disc) Elapsed
Time, and Total (Disc) Remain Time.
●
WHEN PLAYING CD
CD discs have the following playback features:
Track, Disc Time, Track Time, Repeat and
Time Display.
■ Select a Specific Track
1. While the disc is playing, press OSD on
the remote to bring up the Display.
2. Press the
or buttons to highlight "Track" .
3. Press the
(PLAY) button, the text box by
the right side is now highlighted.
4. Use the number buttons on the remote to
enter a track nunber that you want to play.
■ Setting Disc Time
You can skip to a specific disc time by using
the Disc
Time feature in the Display.
1. While the disc is playing, press OSD on
the remote to bring up the Display.
2. Press the
or
buttons to highlight
"Disc Time", while a disc is playing.
3. Press the
(PLAY) button, the text box by
the right side is now highlighted.
4. Use the number buttons on the remote to
enter a disc time that you want to play.
page22
BASIC OPERATIONS (FOR DVD PLAYER)
1. While the disc is playing, press OSD on
the remote to bring up the Display.
2. Press the
or
buttons to highlight "Time
Disp" in the Display while a disc is playing.
3. Press the
(PLAY) button, the time options
appears.
4. Press the
or
buttons to move through
the time options.Press the (PLAY) button
when the option you want to use is highlighted.
5. To make the Display disappear, press the
OSD button on the remote.
DVD Menu Play
Some DVDs have title menus and chapter
menus.
Press (PLAY), the screen shows the menu.
Press
or
to skip to the next or
previous page. Select with number buttons or
direction buttons.
1.
2.
Root
Menu
Volume Control
DVD
DVD
、 CD
11.
Example: select track 13.
●
Press VOLUME on the TV or amplifier to
adjust the volume.
●
1. Press
to enter the next menu.
Press VOLUME on the remote control.
12.
13.
14.
15.
Root
Menu
2. Press number buttons to select directly.
VOLUME+,-
+10
+
3
You can also select as follows:
1. Press to select track 13.
1. Press + to raise the volume.
Root
Menu
2. Press - to lower the volume.
2. Press
12.
13.
14.
15.
(PLAY) to start playing track 13.
Press DVD TITLE once to return to the title
menu.
Press DVD MENU once to return to the root
menu; press it again to resume to play.
page23
BASIC OPERATIONS
PLAY DISCS IN VARIOUS WAYS
Select with Number
Buttons
CD
Audio Mode
●
●
Load a disc. Press number buttons to select
tracks after the unit finishes reading the disc.
DVD
、 CD
You may select a language from a multilanguage DVD.
You may select the right channel, left
channel, or stereooptions from a multichannel CD.
1. If the track number isn’t over 10, just
push buttons 1-10.
Example: push 8 to select track 8.
A.MODE
AUDIO
DVD
8
To select a language, press AUDIO .
The screen will show the following in order:
●
The screen shows:
TRACK08/20
AUDIO 1/2:AC-3 5.1CH
00:00
AUDIO 2/2:AC-3 5.1CH
2. If the track number is over 10 , press + 10
once and a button between 1-10.
Example: if you select track 12, press +10
once and button 2 .
Different discs may differ in languages available.
To select audio channel option, press A.MODE,
the screen shows the following in order:
●
A.MODE
+10
+
2
MONO LEFT
A.MODE
MONO RIGHT
The screen shows:
A.MODE
TRACK12/20
00:00
MIXED MONO
A.MODE
STEREO
page24
PLAY DISCS IN VARIOUS WAYS
Fast Play
CD
To select audio channel option when for CD
playback, press A.MODE . The screen will
show the following in order:
DVD
、 CD
When playing a disc, you can play it in fastforward or fast-reverse mode to find what you
want to view.
A.MODE
MONO LEFT
DVD OR CD
1. While disc is playing, press
A.MODE
to play in
fast-forward mode. Each time you press the
MONO RIGHT
button, the screen shows the following in
order:
A.MODE
FF
MIXED MONO
A.MODE
STEREO
①
②
③
④
⑤
⑥
2. While disc is playing, press
You may select one mode.
2X
4X
8X
16X
32X
to play in
fast-reverse mode. Each time you press the
Notes:
●
button, the screen shows the following in
Different discs differ in languages available.
Mute
DVD
order:
、 CD
FR
When playing a disc, this function removes the
sound.
1. TO REMOVE SOUND
Press MUTE , the screen shows "
①
②
③
④
⑤
⑥
2X
4X
8X
16X
32X
".
3. Press
(PLAY) to switch to normal play
while in fast-forward or fast-reverse playing
MUTE
mode.
2. TO RESUME SOUND
Press MUTE again, to resume sound.
page25
PLAY DISCS IN VARIOUS WAYS
Slow Play
Playing A Disc
Repeatedly
DVD
Enjoy slow motion by the following the steps
below.
DVD
SLOW
You can repeat a title or chapter.
1. To repeat a chapter:
Press REPEAT , the screen will show:
DVD
1. Press SLOW to play in slow motion.
REPEAT
CHAPTER
SLOW
2. To repeat a title:
Press REPEAT twice, the screen will show:
The screen shows the following in order:
1/2
1/4
1/16
2. Press
speed.
1/8
1/8
REPEAT
1/16
1/4
TITLE
1/2
(PLAY) to resume play at normal
Repeat Play
DVD
3. To repeat all:
Press REPEAT third time, the screen
shows "
ALL".
4. To remove "REPEAT" function:
Press REPEAT until "
ALL"
disappears.
、 CD
This function can be used to repeatedly play a
title, chapter, track, or a whole disc.
CD
You may repeat a track or an entire disc
according to the following steps.
1. To repeat a track:
Press REPEAT , the screen shows
"
TRACK".
The unit plays the current track.
●
REPEAT
page26
PLAY DISCS IN VARIOUS WAYS
Select Subtitles
REPEAT
TRACK
DVD
This operation works only with discs with
multiple subtitle languages recorded.
2. To repeat a disc:
Press REPEAT , the screen shows
"
ALL".
The unit plays all the tracks on the disc.
REPEAT
ALL
3. To remove "REPEAT" function:
Press REPEAT till "
ALL" disappears.
Zoom Play
SUBTITLE
DVD
This function can be used to watch a
motion or motionless picture.
DVD
1. Press SUBTITLE repeatedly until the
desired language is selected.
The screen shows:
ZOOM
1. Press ZOOM during playback,
the screen shows:
SUBTITLE
SUBTITLE01/03:ENGLISH
2X
The picture is enlarged twice the size.
2. Press ZOOM again, the screen shows:
2. Remove the subtitle.
Press SUBTITLE until the screen shows
"SUBTITLE OFF".
3X
Notes:
For some discs, subtitles cannot be
removed.
Different discs differ in the language of
subtitles.
If the subtitles of discs cannot be selected,
the screen shows "
" when you press
SUBTITLE .
The picture is enlarged three times the size.
Note: The unit has six zoom levels:
2X, 3X, 4X, 1/2 , 1/3 , and 1/4 .
3. Press , , , to move the enlarged
picture.
4. To resume the picture, press ZOOM until
the picture is in normal size.
●
●
●
page27
PLAY DISCS IN VARIOUS WAYS
Angles Select
Program Play
DVD
Some discs have images with different viewing
angles, you may select among them. For
example, when you watch a running train, you
may watch it from the front, the left window or
the right window without stopping it.
DVD
CD
P.MODE
To use the program playback feature, you must
enter the order in which you want the titles (and
chapters) on the DVD or the tracks on the CD
to play by creating a program.
DVD
1. Press P.MODE until the screen shows:
PROGRAM: TT(20)/CH (--)
01 TT:_ _ CH:_ _ 06 TT:_ _ CH:_
02 TT:_ _ CH:_ _ 07 TT:_ _ CH:_
03 TT:_ _ CH:_ _ 08 TT:_ _ CH:_
04 TT:_ _ CH:_ _ 09 TT:_ _ CH:_
05 TT:_ _ CH:_ _ 10 TT:_ _ CH:_
EXIT
NEXT
ANGLE
Example:
A DVD has four viewing angles at your option.
1. Press ANGLE to select ANGLE1.
_
_
_
_
_
2. Use the number buttons on the remote to
enter the title (and chapter) you want to play
first. The title (and chapter) number you
entered appears in the box. For example: Enter
Chapter 1 in Title 8, the screen shows:
1/4
PROGRAM: TT(20)/CH (--)
01 TT:0 8 CH:0 1 06 TT:_ _ CH:_
02 TT:_ _ CH:_ _ 07 TT:_ _ CH:_
03 TT:_ _ CH:_ _ 08 TT:_ _ CH:_
04 TT:_ _ CH:_ _ 09 TT:_ _ CH:_
05 TT:_ _ CH:_ _ 10 TT:_ _ CH:_
EXIT
START
NEXT
2. Press ANGLE to select other angles , the
screen shows respectively:
_
_
_
_
_
3. The cursor jumps to the next spot in the
program list section. Make sure the box is
highlighted and enter your next track.
4.Continue adding title (and chapter) until your
program is complete. You can play your
program by highlighting START and press
PLAY .
Note: If you want to program more than 10
titles (and chapters), highlight NEXT
and press PLAY to go to the next
page. Proceed to program 11-20 in the
same way titles 1-10 were
programmed.
5. To remove program playback, press the
STOP button twice during the program play.
2/4 (select ANGLE2)
3/4 (select ANGLE3)
4/4 (select ANGLE4)
3. To resume normal playback, press ANGLE
to select original angle.
page28
PLAY DISCS IN VARIOUS WAYS
Shuffle (Random)
Play
DVD
CD
CD
1. Press P.MODE until the screen shows:
PROGRAM: TRACK
01 _ _
02 _ _
03 _ _
04 _ _
05 _ _
EXIT
(01-20)
06 _ _
07 _ _
08 _ _
09 _ _
10 _ _
NEXT
The unit can play DVD chapters or audio
tracks in random order.
The order is different each time.
1. Press P.MODE to select shuffle or
2. Use the number buttons on the remote to
random play mode when a disc is playing.
enter the track number you want to play
P.MODE
first. The track number entered appears in
the box. The example: To program track 8
of a CD to play first, enter 8, and the screen
shows:
The screen shows:
PROGRAM: TRACK (01-20)
01 08
06 _ _
02 _ _
07 _ _
03 _ _
08 _ _
04 _ _
09 _ _
05 _ _
10 _ _
EXIT
START
NEXT
SHUFFLE
OR
RANDOM
2. Shuffle or random play will begin.
3. The cursor jumps to the next spot in the
program list section. Make sure the box is
3. Remove shuffle or random play.
highlighted and enter your next track.
●
When playing a DVD disc, press ■ twice.
●
When playing a CD disc, press ■ twice.
4. Continue adding tracks until your program
is complete. You can play your program by
highlighting START and press PLAY .
Note: If you want to program more than 10
tracks, highlight NEXT and press
PLAY to go to next page. Program 1120 in the same way 1-10 were
programmed.
5. To remove program playback, press the
STOP button during the program play.
page29
MENU SETTING
According to the recorded information and
external equipment, set the following functions
for the player to obtain the best playing
status.
The screen shows:
-- Audio Setup Page -Speaker Setup
Dolby Digital Setup
Equalizer
SETUP
3D Processing
Main Page
Go To Speaker Setup Page
1.Press SETUP to set options in the main menu.
Press direction buttons ( or ) to highlight
"Dolby Digital Setup", and press (PLAY) to
enter "Dolby Digital Setup" Page. The screen
shows the submenu for your selection.
●
SETUP
The screen shows:
The main menu appears on the screen, with
icons across the top of the screen, illustrating
General Setup, Audio Setup, Preference
Setup, Password Setup, and Exit Setup.
The screen shows:
--Dolby Digital Setup-Dual Mono
STR
Stereo
L-Mono
R-Mono
Mix-Mono
Dynamic
--Setup Menu--Main page --
Audio Setup
General Setup
Audio Setup
Press direction buttons
Mono".
The screen shows:
●
Preference Setup
Password Setup
,
to select "L-
Exit Setup
Go To General Setup Page
--Dolby Digital Setup-Dual Mono
2. Press direction buttons ( or ) to select
and press
(PLAY) to confirm.
Example: Select "Audio Setup" and do some
setup.
Press direction button
to highlight "Audio
Setup", press
(PLAY) to enter "Audio
Setup Page".
STR
Stereo
L-Mono
R-Mono
Mix-Mono
Dynamic
●
Audio Setup
page30
MENU SETTING
Press
(PLAY) to confirm your selection.
Set "Dual Mono" in "Dolby Digital Setup" to
"L-Mono".
The sereen shows:
●
-- General Setup Page -TV Display
Wide
Normal/PS
Normal/LB
Wide
OSD Lang
ENG
--Dolby Digital Setup-Dual Mono
L
English
Fran ais
Stereo
Espa ol
L-Mono
Captions
R-Mono
On
On
Off
Mix-Mono
Dynamic
Screen Saver On
Audio Setup
On
Off
Main Page
3. Exit setup menu.
Press the direction button
to exit from
"Dual Mono".
Press the direction button
to exit from
"Dolby Digital Setup".
Press the direction button to highlight
"Main Page" and press
(PLAY). The
screen shows:
●
■ TV DISPLAY
1. NORMAL/PS
This is selected when the unit is connected
to a normal TV.
Wide- screen images are shown on the
screen, but with some parts cut automatically.
●
●
Setup Page -- Main Page
General Setup
2. NORMAL/LB
This is selected when the unit is connected
to a normal TV. Wide-screen images are
shown on the screen with black bars on the
top and bottom of the screen.
Audio Setup
Preference Setup
Password Setup
Exit Setup
Go To Audio setup Page
Press the direction button to highlight "Exit
Setup" and press (PLAY) to exit setup
menu completely.
NOTE:You can also keep pressing the
direction button until the cursor is
moved to the last icon illustrating
Exit, then press the (PLAY) button to
exit setup menu completely.
●
3. WIDE
This is selected when the unit is
connected to a wide-screen TV.
General Setup
NOTE: You can use the WIDE button on the
remote control to set TV display mode.
The setting structure is :
page31
MENU SETTING
■ OSD LANGUAGE
●
●
●
Lt/Rt
A disc recorded multi channel soundtrack, the
output signal will be incorported to left and right
channel.
STEREO
A disc recorded multi channel soundtrack, the
output signal will be incorported to stereo.
●
ENGLISH
The OSD is in English.
FRENCH
The OSD is in French.
SPANISH
The OSD is in Spanish.
●
■ DOLBY DIGITAL SETUP
■ CAPTIONS
The setting structure is:
ON
Subtitles are shown.
OFF
Subtitles are hidden.
●
- - Dolby Digital Setup - Dual Mono STR
Stereo
L-Mono
R-Mono
Mix-Mono
FULL
3/4
Dynamic
2/4
1/4
Audio Setup
OFF
●
■ SCREEN SAVER
The screen saver image appears when the unit
stops or the image is frozen for a few minutes. The
screen saver prevents damage to the TV screen.
ON: Start the screen saver.
OFF: Remove the screen saver.
●
●
DUAL MONO
This is the output mode of the L and R signals
of the set audio output. If it is set to "MIXMONO", the function only works when the DVD
being played is 5.1-channel.
Dynamic
This is selected to adjust linear compression
rate to obtain the different compression results
of the signals.
●
●
Audio Setup
The setting structure is:
■ EQUALIZER
This will help you to select graphic equalizer
patterns according to the genre of the music
being played,and adjust the equalizer.
The setting structure is:
- - Audio Setup Page - Speaker Setup
Dolby Digital Setup
Equalizer
- - Equalizer Page - EQ Type
None
None
Rock
Pop
Live
Dance
Techno
Classic
Soft
Audio Setup
3D Processing
Main Page
■ SPEAKER SETUP
The setting structure is:
- - Speaker Setup Page - Downmix
STR
Lt/Rt
Stereo
Audio Setup
EQ TYPE
You can select music category by pressing the
direction buttons and confirm by pressing the
PLAY button.
●
page32
MENU SETTING
■ 3D PROCESSING
Password Setup
The setting structure is:
The setting structure is :
- - 3D Processing Page - V SURR
Reverb Mode
- - Password Setup Page - PW Mode
Off
On
Off
Password
Change
Main Page
Off
On
Off
Off
Off
Concert
Living Room
Hall
Bathroom
Cave
Arena
Church
■ PASSWORD MODE
●
●
Audio Setup
ON: The password function is on and
"PARENTAL" is dim and cannot be
selected.
OFF : The password is locked,
"PARENTAL" can be selected.
■ PASSWORD CHANGE
Select this to adapt the code, the screen
shows:
V SURR
Use to turn the above function off.
REVERB MODE
Use to select a Reverb Mode which you want.
●
Old Password
●
New Password
Confirm PWD
OK
Enter a password according to the screen.
Note: The password is automatically
factory set to 99999.
page33
MENU SETTING
Preferences
The setting structure is :
■ LANGUAGE SELECTION
If a language mentioned above is recorded on
the disc, you can select sound, subtitles or disc
menu languages. If not, the language recorded
on the disc is shown.
■ PARENTAL LOCK
When playing a disc with parental lock function,
you may select an age control grade according
to the rating your desire.
Example: If "PG" is selected, you cannot play
DVD video discs rated higher than the PG
grade.
■ DEFAULT >> RESET
Each function setting returns to the initial status
in the factory if you select this option.
Note:
"PREFERENCES" can only be selected when
password is OFF when the unit is in stop
mode.
- - Preference Page - Audio
ENG
English
French
Spanish
Chinese
Japanese
Subtitle
ENG
English
French
Spanish
Chinese
Japanese
Off
Disc Menu
●
ENG
English
French
Spanish
Chinese
Japanese
Parental
08
1 KID SAFE
2 G
3 PG
4 PG 13
5 PGR
6 R
7 NC17
8 ADULT
Default
Reset
Main Page
page34
KODAK PICTURE CD PLAYBACK
A Kodak Picture CD has the size and shape of a regular CD. You can order a KODAK Picture CD simply by
checking the box on the photofinishing envelope when you drop off a roll of film (35 mm or Advanced Photo
System (APS) color print film) at the time of processing in photo processing outlet displaying "Kodak Picture
CD"sign. When your order is returned, you receive your prints, negatives, and your full roll of pictures safely
stored on your KODAK Picture CD. Each KODAK Picture CD brings you the tools to enhance, share and
manage your pictures on your computer.
Now, you can playback Kodak Picture CDs on XXX DVD players and view your pictures on your TV in the
comfort of your living room.
Playing back your Kodak Picture CD
The new feature enables the decoding of JPEG files from a Kodak Picture CD disk.
Playback modes
Normal
When a Kodak Picture CD is inserted on a player an automatic slide show is launched. Each picture in the
Kodak Picture CD will be displayed consecutively in a slide-show fashion and will be scaled to fit in the TV
screen. Twelve slideshow transition modes are provided, use "P. MODE" key to select.Select transition
mode prior to start of slideshow if one mode is desired for the entire show.
Mode 0: no special transition effect (by default)
Mode 1: wipe from top to bottom
Mode 2: wipe from bottom to top
Mode 3: wipe from left to right
Mode 4: wipe from right to left
Mode 5: wipe from left top to right bottom
Mode 6: wipe from right top to left bottom
Mode 7: wipe from left bottom to right top
Mode 8: wipe from right bottom to left top
Mode 9: wipe from center to top/bottom
Mode 10: wipe from center to left/right
Mode 11: wipe from top/bottom to center
Mode 12: wipe from left/right to center
Mode 13: horizontal blinds
Mode 14: vertical blind
Mode 15: wipe from edge to center
Mode 16: random
Customer can set transition effects for each picture in a slideshow by using the "P. MODE" functions while
viewing a slideshow.The last transition mode selected will be used in any future slideshows.
To display an image indefinitely, press the PAUSE key. To view the Next or Previous picture press NEXT or
PREVIOUS keys. To resume the slideshow press the PLAY key.
Image Rotation
There are four modes to rotate a picture:"Invert", "Mirror", "Left", and "Right". These operations are allowed
only when a picture is being displayed normally and will be cancelled automatically when a new picture is
displayed.The arrow key is used to select the diferent rotation modes:
Up
Down
Left
Right
-Invert/Normal
-Mirror/Normal
-Turn left
-Turn right
Zoom
We provide both ZOOM in/out and Zoom pan function for the pictures. The "ZOOM" key is used to turn on
or off this function. When this mode is on, any picture will be displayed at the last ratio selected by the user.
A message on the screen will indicate the current Zoom ratio.
If zoom mode is on, "FF" and "FR" keys are used to control the ratio of zoom in/out. With ZOOM mode off, a
picture is scaled to fit the TV screen.
Notes: During ZOOM function, slideshow transition and image rotation are disabled. TO cancel the ZOOM
function, press the ZOOM key again and resume the slideshow.
Digest
The "MENU" or "STOP" key is used to display thumbnail size pictures. After it is enabled, up to 9 scaleddown thumbnail pictures will be displayed on the screen. The "NEXT" and "PREV" keys can be used to
display the next/prev nine pictures in the the Kodak Picture CD.
You can select any of the nine displayed thumbnails by using the Arrow Keys and pressing the "PLAY" key.
The thumbnail will be enlarged to fit the TV screen and the slide show will statr. If you desire to display an
image indefinitely, press the PAUSE key. To view the Next or Previous picture press NEXT or PREVIOUS
keys. To resume the slideshow press the PLAY key.
IMPORTANT NOTE:
Quality of pictures displayed on the screen is highly dependent on the viewing device.
page35
TROUBLESHOOTING _ _ WATCHING TV
Please check the following items before asking for repair service.
Check Items
Check the contact of sockets is all right.
Check the TV main power is on.
Symptom
Neither picture nor
sound.
●
Picture is OK, but no
sound.
●
Check the volume control is set to minimum or mute.
●
Check the color control and adjust it properly.
Check the programme is in color or in black & white.
Sound is OK, but no
color.
●
●
●
The picture is
overlapped image.
Picture has ’’snow
noise ’’.
●
●
●
Remote control does
not work.
Check the antenna or its connection is correct and if not, correct the
antenna fault or connection cable fault.
Check if car traffic or neon sign disturbs the sound effect.
●
Check the susceptible interference by other electronic devices such
as radio and television and keep magnetic or electronic devices
away from the TV.
●
Long distance from the station or other radio waves can generate
bad sound. Reception. If so, change the mode to Mono.
●
Check if the batteries in the Remote control die.
Check if any object between IR sensor of the TV and the Remote
control does not obstruct.
Stripes on picture.
Bad stereo or SAP
sound.
Check the antenna is installed correctly and if not, adjust the antenna
toward the broadcasting station.
Check the ’’FINE TUNE ’’is set up correctly and if not, adjust the fine
tuning properly.
●
Check the resolution and frequency of your PC. Then, adjust them to
optimum condition for LCD TV: 1280X768 and 60Hz.
● Refer to the table of PC mode input format indicated on page 15.
(Not being registered resolution and frequency on the table won’t be
displayed.)
●
’’Out Of Range’’
appears on the
screen.
’’No Signal’’ appears
on the screen.
Image is not clear in
PC mode.
Image is not
centered.
●
Ensure that the signal cable is firmly connected to PC and TV.
●
Adjust the PHASE control. (Refer to the PICTURE ADJUSTMENT.)
●
Adjust the H-POSITION, and IMAGE SIZE Control. (Refer to
the WINDOW ADJUSTMENT.)
page36
TROUBLESHOOTING _ _ WATCHING DVD
If you experience the following problems while using the unit, this troubleshooting guide can
help you.
No sound
●
●
●
No image
●
●
●
Bad sound quality
●
●
Disc cannot be played
●
●
●
●
Check if the unit is connected securely.
Make sure the TV or amplifier is working properly.
Make sure the amplifier is set to receive DVD
signal output.
Check if the unit is connected securely.
Make sure the TV is working properly.
Make sure the color system is set correctly.
Make sure the audio output mode is set correctly.
Make sure the audio connection between the
unit and amplifier is in place.
There is no disc in the unit.
Put the disc on the disc tray properly with the
label side up.
Clean the disc.
Moisture has condensed in the unit. Remove
the disc and leave the unit on for about an
hour.
The unit doesn’t operate
normally
●
Disconnect the power plug and insert it into the
wall outlet again.
Remote control does not work
●
Remove barriers between the remote control
and the unit.
Point the remote control at the remote control
sensor of the unit.
Replace the batteries with new ones.
●
●
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by
Macrovision Corporation, and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
page37
TECHNICAL SPECIFICATIONS
LCD
PANEL
RESOLUTION
ACTIVE AREA (mm)
VIEWING ANGLE (°,H/V)
26’’ WIDE TFT LCD
1280 X 768 X RGB
370 X 222
176/176
DIMENSION
WITH STAND (mm)
WITHOUT STAND (mm)
770 X 552 X 210
770 X 443 X 100
●
●
●
●
●
●
●
WEIGHT (WITHOUT ACCESSORIES)
15.8kg
TV-FUNCTION
TV STANDARD
TUNING SYSTEM
FREQUENCY RANGE
STEREO
CATV
NTSC
ELECTRIC TUNING SYSTEM
VHF/UHF
MTS + SAP
125 CHANNELS
SOUND
SOUND OUTPUT
8W×2
TERMINALS
AV IN
COMPONENT
MONITOR OUT
PC IN
ANTENNA IN
VIDEO, S-VIDEO, AUDIO L&R
Y, Pb (Cb), Pr (Cr)
VIDEO OUT
D-SUB 15PIN RGB IN, DVI
F-TYPE
DVD
Applicable disc
DVD/CD-R/CD-RW/CD/MP3/Picture CD
Power adapter
Output
Input
DC 24Volt, 6.0 Ampere
100~240Volt
Power consumption
Power consumption (TV)
Power consumption (DVD)
130 Watt
≤130 Watt
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
This manual is only for your reference, any change to the design and specifications will not be advised.
page38
page39
page40
Download PDF

advertising