Operating instructions | Aiwa XD-DV370 DVD Player User Manual

DVD PLAYER
XD-DV370
OPERATING INSTRUCTIONS
8A-AV4-906-11
000731BMK-Y-L
K
PREPARATION
WARNING
(FOR USE IN THE UNITED KINGDOM)
This appliance is supplied with a fitted three pin mains plug.
A 13 amp fuse is fitted in the plug.
Should the fuse need to be replaced, use a 13 amp fuse
approved by ASTA or BSI to BS 1362. When replacing the
fuse, you must ensure that any removable fuse covers are
correctly refitted.
If you should lose the fuse cover, please contact your
nearest AIWA dealer.
Do not cut off the plug from this appliance
If the plug fitted is not suitable for the power points in your
home, or the cable is too short to reach a power point,
obtain an appropriate safety approved extension lead or
adaptor. If in any doubt please consult a qualified electrician.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
“CAUTION:TO REDUCE THE RISK OF
ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.”
If the plug is cut off, remove the fuse and dispose of the
plug immediately.
There is a danger of severe electrical shock
if the cut off plug is inserted into any 13 amp
socket.
If a new plug is to be fitted please ensure it contains a 13
amp fuse, otherwise the circuit should be protected by a 5
amp fuse at the distribution board.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
BLUE
— NEUTRAL
BROWN — LIVE
As the colours of the wires in the mains lead of this
appliance may not correspond with the colour markings
identifying the terminals in your plug, proceed as follows:
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
This DVD player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
CAUTION!
The wire which is coloured BLUE must be connected to
the terminal which is marked by the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to
the terminal which is marked by the letter L or coloured
RED.
DO NOT connect either the BLUE or BROWN wire of the
mains lead to the earth terminal (marked with the letter E
or by the earth symbol 2 or coloured GREEN or GREEN/
YELLOW) of a three pin plug.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Invisible laser radiation when open and
inter locks defeated. Avoid exposure
to beam.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude al funktion. Undgå udsættelse for stråling.
VAROITUS!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessaa
mainitulla tavalla saattaa altistaa käyttäjän
tur vallisuusluokan 1 ylittävälle näkymättömälle
lasersäteiylle.
VARNING!
Om apparaten används på annat sätt än i denna
bruksanvisning specificerats, kan användaren utsätta
för osnylig laser-strålning, som överskrider gränsen för
laserklass 1.
2
Read the Operating Instructions carefully and completely
before operating the unit. Be sure to keep the Operating
Instructions for future reference. All warnings and cautions
in the Operating Instructions and on the unit should be
strictly followed, as well as the safety suggestions below.
Installation
1 Water and moisture — Do not use this unit near water,
such as near a bathtub, sink, swimming pool, or the
like.
2 Heat — Do not use this unit near sources of heat,
including heating vents, stoves, or other appliances that
generate heat. This unit should not be placed in
temperatures less than 5˚C (41˚F) or greater than 35˚C
(95˚F).
3 Mounting place — Place the unit:
- on a flat , even surface
- away from strong magnetic fields
- at least one metre away from any radios or receivers
Do not place heavy objects on the unit.
4 Ventilation — The unit should be situated with adequate
space around it so that proper heat ventilation is assured.
Allow a clearance of 10 cm (4 in.) from the rear and the
top of the unit, and 5 cm (2 in.) from each side.
- Do not place the unit on a bed, rug, or similar surface
that may block the ventilation openings.
- Do not install the unit in a bookcase, cabinet, or airtight
rack where ventilation may be impeded.
- To avoid internal heat build-up, do not cover
the ventilation openings on the rear panel.
5 Foreign objects and liquid — Be careful that foreign
objects or liquid do not enter the unit through the
ventilation openings.
6 Carts and stands — The unit should be moved with
care when placed or mounted on a stand or cart.
Sudden stops, excessive force, or an uneven surface
may cause the unit or cart to fall over.
7 Condensation — Moisture may form on the pickup lens
when:
- This unit is moved from a cold spot to a warm spot
- A heating system has just been turned on
- The unit is used in a very humid room
- The unit is cooled by an air conditioner
When this unit has condensation inside, it may not
function normally. Should this occur, leave the unit
for a few hours, then try to operate again.
Electric power
1 Power sources — Connect this unit only to power
sources specified in the Operating Instructions, and as
marked on the unit.
2 AC power cord
- When disconnecting the mains lead, pull it out by the
mains plug. Do not pull the mains lead itself.
- Never handle the mains plug with wet hands, as this
could result in fire or electrical shock.
- Mains lead should be firmly secured to avoid being
severely bent, pinched, or walked upon. Pay particular
attention to the mains lead from the unit to the mains.
- Avoid overloading mains plugs and extension leads
beyond their capacity, as this could result in fire or
electrical shock.
3 When not in use — Unplug the mains lead from the
mains if the unit will not be used for several months or
more. When the mains lead is plugged in, a small
electrical current continues to flow into the unit, even if
the power is turned off.
4 In case of lightning — Immediately disconnect the
mains lead from the mains.
Maintenance
Clean the unit only as recommended in the Operating
Instructions.
Damage requiring service
Have this unit serviced by a qualified service technician if:
- The mains lead or plug has been damaged
- A foreign object or liquid has entered the unit
- The unit has been exposed to rain or water
- The unit does not seem to operate normally
- The unit exhibits a marked change in performance
- The unit has been dropped, or the cabinet has been
damaged
DO NOT OPEN THE CABINET AND ATTEMPT TO
SERVICE THE UNIT YOURSELF.
3
INTRODUCTION
IMPORTANT SAFETY
INSTRUCTIONS
TABLE OF CONTENTS
Introduction
Precautions ............................................................... 2
Before Use ................................................................. 5
Supported disc formats .................................... 5
Disc-related terms .............................................. 5
Types of video CDs ............................................ 5
Handling the unit ................................................ 6
Handling discs .................................................... 6
Cleaning the unit ................................................ 6
Cleaning discs .................................................... 6
Storing discs ...................................................... 6
Notes on copyright ............................................ 6
Parts and Controls ................................................... 7
Front panel .......................................................... 7
Remote control ................................................... 8
Display window .................................................. 9
Preparations
Connections ............................................................ 10
A Connecting to a TV set only ....................... 11
B Connecting to a TV set and an amplifier
with a Digital In jack .............................. 12
C Connecting to a TV set and an audio
system ..................................................... 13
D Connecting to an AV amplifier equipped
with a Dolby Digital (AC-3) decoder .... 14
E Connecting to an AV amplifier equipped with
a DTS decoder ......................................... 15
F Connecting to a TV set and an AV amplifier
with the Dolby Pro Logic Surround
system ..................................................... 16
Connecting to a TV set equipped with S-video
jack .............................................................. 17
Connecting to a TV set or monitor with video
input connector .......................................... 18
Remote control ....................................................... 19
Basic Operations
Playback .................................................................. 20
Still (Pause) ....................................................... 21
Frame Advance (DVD/VCD) ............................. 21
Stopping playback ........................................... 21
Fast Forward, Reverse ..................................... 22
Slow Playback (DVD/VCD) ............................... 22
Skipping ............................................................ 22
On Screen Display (OSD) menu ..................... 23
Detailed description of each OSD menu ....... 24
More Features
Search ...................................................................... 25
Title search (DVD)/Track search (VCD without
PBC/CD) ...................................................... 25
Chapter search (DVD) ...................................... 26
Time search (DVD) ........................................... 26
Mark Search (DVD) ........................................... 27
Zooming and changing the angle ......................... 28
Zoom function (DVD) ....................................... 28
Changing the angle (DVD) ............................... 28
Random and repeat playback ............................... 29
Random playback (Karaoke DVD/CD) ............ 29
Repeat playback (DVD) .................................... 29
Repeat playback (VCD without PBC/CD) ...... 30
Repeating a portion between two specified
4
points (A-B Repeat) ................................... 30
Programmed playback ........................................... 31
Creating a 3D surround effect .............................. 32
Changing the audio track ...................................... 33
Changing audio tracks (DVD) ......................... 33
Changing audio tracks (VCD/CD) ................... 33
Displaying and changing subtitles ....................... 34
Playing back an MP3 disc ..................................... 35
Notes on MP3 disc ........................................... 35
Tips on recording MP3 .................................... 35
Glossary ............................................................ 35
Playing back with MP3 .................................... 36
Programmed playback with MP3 .................... 37
Repeat playback with MP3 .............................. 38
As Necessary
Changing setup values .......................................... 39
Basic operations .............................................. 39
Disc Audio ......................................................... 40
Disc Subtitle ..................................................... 41
Disc Menu ......................................................... 41
Rating ................................................................ 41
Password ........................................................... 42
TV Aspect .......................................................... 43
Menu Language ................................................ 44
TV Output Select .............................................. 45
Others (Pseudo PAL/PBC) .............................. 45
Digital Audio Output ........................................ 46
Language codes ............................................... 47
Troubleshooting ..................................................... 48
Specifications ......................................................... 49
Features
DVD: providing a completely new dimension in video
entertainment.
• With the multi-language function* you can select an
audio soundtrack in up to 8 languages, and subtitles in
up to 32 languages.
• With the multi-angle function* you can select a viewing
angle of scenes shot from multiple camera angles and
recorded on the disc.
• With the parental lock function* you can prevent
playback of specified discs unsuitable for certain
audiences.
* All of the above functions are dependent on the DVD
software.
High quality digital audio and images
• The linear PCM sound of a 96 kHz/24 bit creates audio
quality superior to that of audio CDs.
• Compatible with video CDs and audio CDs as well
as DVDs
• MP3 playback
Accessory checklist
Remote control (1)
Audio cord (1)
Video cord (1)
Operating Instructions
BEFORE USE
Supported disc formats
This DVD player can play discs with the following marks
only.
DVDs
(8 cm disc/12 cm disc)
Video CDs (VCDs)
(8 cm disc/12 cm disc)
Audio CDs
(8 cm disc/12 cm disc)
In addition, this unit can play back a CD-R or CD-RW that
contains audio titles or MP3 files.
NOTES
• Depending on the condition of the recording equipment
or the CD-R/RW disc itself, some CD-R/RW discs can
not be played on this unit.
• The unit can not play back the CD-R/RW discs
that contain no data or different kinds of formatted
data other than MP3.
For more information about MP3, see page 35.
• Do not attach any seal or label to either side (the labeled
side or the recorded side) of a disc.
• Do not use irregular shape CDs (example: heart-shaped,
octagonal ones). It may result in malfunctions.
Notes on colour system
Although this unit is designed for the PAL,NTSC and Multi
colour system, the default setting sets to the PAL colour
system. When connecting to a TV set which is NTSC or
Multi colour system, you need to change the TV SYSTEM
SELECT switch(see page 10).
Note on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise will be
exhibited from the analogue stereo outputs. To avoid possible
damage to the audio system, the consumer should turn down
the volume before playing back such a disc, adjust the volume
gradually, and keep the volume level low. To enjoy DTS Digital
SurroundTM playback, an external 5.1 channel DTS Digital
SurroundTM decoder system must be conneted to the digital
output of this unit.
Disc-related terms
Title (DVD only)
The longest section of a picture or a musical piece on a DVD;
a movie for a picture piece on video software, or an album for
a musical piece on audio software. Each title is assigned a
title number enabling you to locate the title you want.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles.
A title is composed of several chapters. Each chapter is
assigned a chapter number, enabling you to locate the
chapter you want. Depending on the disc, there may be no
chapters recorded.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD or
an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (playback control) functions,
moving pictures and still pictures are divided into sections
called “Scenes”. Each scene is displayed in the menu
screen and assigned a scene number, enabling you to
locate the scene you want.
A scene is composed of one or several tracks.
Types of video CDs
Notes on DVDs and video CDs
Some playback operations of DVDs and video CDs may
be intentionally fixed by software manufacturers. As this
player plays DVDs and video CDs according to disc
contents designed by the software manufacturer, some
playback features of this player may not be available, or
other functions may be added.
Also refer to the instructions supplied with the DVDs and
video CDs.
Some DVDs made for business purposes may not be
played on this player.
Region code of the DVD player and DVDs
There are two types of video CD (VCD)s.
Video CDs equipped with PBC (Version 2.0)
PBC (playback control) allows you to interact with the
system via menus, search functions or other typical
computer-like operations. Moreover, still pictures of high
resolution can be played, if they are included in the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs allow
playback of video pictures as well as sound, but they are
not equipped with PBC.
This DVD player is designed and manufactured for playback
of region “2” encoded DVD software. Region code labels
appear on the labels of some DVD discs to indicate which
type of player can play those discs. Unless “2” is included
in these labels, or “ALL” appears on the DVD disc labels,
those discs cannot be played on this player. If you try to
play these discs, the message “Check Regional Code” will
appear on the TV screen. Some DVD discs may not have a
region code label even though their playback is prohibited
by area limits.
5
INTRODUCTION
Please read the following before operating the DVD player.
BEFORE USE (CONTINUED)
Handling the unit
When shipping the DVD player
The original shipping carton and packing materials come
in handy. For maximum protection, re-pack the unit as it
was originally packed at the factory.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture
quality and sound distortion. Before playing, clean the disc
with a clean cloth. Wipe the disc from the center out.
When setting the DVD player
The picture and sound of a nearby TV, VCR or radio may
be distorted during DVD playback. In this case, position
the player away from the TV, radio or VCR, or turn off the
player after removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray, near
the player. Do not leave rubber or plastic products in contact
with the player for a long period of time. They will leave
marks on the surface.
Do not use strong solvents such as alcohol, benzene,
thinner, commercially available cleaners or anti-static spray
intended for analogue records.
Storing discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not get
on the surface.
Do not stick paper or tape on the disc.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents, such as alcohol,
benzene or thinner, as these might damage the surface of
the player.
To obtain a clear picture
The DVD player is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or worn
down, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your Aiwa dealer.
6
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of heat,
or leave it in a parked car exposed to direct sunlight, as
there may be a considerable temperature increase inside
the car.
Notes on copyright
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyright material without
permission.
This product features the copy protection function
developed by Macrovision. Copy protection signals are
recorded on some discs. When recording and playing the
pictures of these discs on a VCR, the picture noise will
appear.
This product incorporates copyright protection technology
that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by
Macrovision Cor poration. Reverse engineer ing or
disassembly is prohibited.
PARTS AND CONTROLS
The instructions in this manual refer mainly to the buttons on the remote control. Buttons on the main unit with the same
names as those on the remote control can be used as well.
2
1
3
4
#
5
@
6
!0
INTRODUCTION
Front panel
7
9
8
1 POWER button
9 g/t button
Press to turn on and off the unit.
2 6STANBY/ON indicator
• Lights in red when the unit is in standby mode.
• Lights in green when the unit is turned on.
3 Disc tray
Loading and removing discs.
4 z OPEN/CLOSE button
Press to open and close the disc tray.
5 PLAY C button
Press to begin playback.
6 STOP s button
Press to stop playing back a disc.
7 ENTER button
Press to execute or fix the selected item on the disc
menus.
8 i/ k/ j/ l cursor buttons
Press to select an item.
Press to skip to the next track. Hold down to playback a
disc forward.
0 MENU button
Press to display the DVD menu on the TV screen.
! a button
Press to pause playback.
@ r/f button
Press to return to the beginning of the current track or
skip back to the previous track. Hold down to play back
a disc in reverse.
# Display window
Displays the information of the unit's status.
7
PARTS AND CONTROLS (CONTINUED)
Remote control
!
0
9
8
7
6
5
4
@
0 OPEN/CLOSE button
#
! MARK SEARCH button
$
Press to display the marked point on the TV screen
during playback or stop mode.
@ ZOOM button
Press to enlarge the picture during a DVD playback.
# REPEAT button
Press to execute a repeat playback.
$ SURROUND button
Press to turn on and off the 3D surround effect.
% A-B button
Press to memorize the point you want to repeat.
^ ANGLE
button
Press to change the picture angle during a DVD
playback.
& AUDIO SELECT button
Press to select the sound tracks on the DVD, Video CD
or audio CD.
* SUBTITLE SELECT button
Press to change the subtitle language during a
DVD playback.
( RANDOM button
Press to execute a random playback.
) PROGRAM button
Press to execute a programmed playback.
- MENU button
Press to display the menu programs on the DVD.
= F.SLOW button
Press to execute a forward slow playback when
playing back a DVD or Video CD.
[ B.SLOW button
Press to execute a backward slow playback when
playing back a DVD.
]SETUP button
Press to display the setup menu on the TV screen.
\ gbutton
Hold down to play back a disc forward.
; fbutton
Hold down to play back a disc in reverse.
' tbutton
Press to skip to the next track.
, cbutton
Press to begin a playback.
. sbutton
Press to stop playing back a disc.
/ rbutton
Press to return to the beginning of the current track or
skip back to the previous track.
%
^
&
*
(
)
=
[
3
]
\
2
;
'
1
,
.
/
1 POWER button
Press to turn on and off the unit.
2 ON SCREEN DISPLAY ON/OFF button
Press to display the On Screen Display information.
3 a button
Press to pause a playback.
4v RETURN button
• Press to display the title menu on the video CD that
supports PBC (Playback Control).
• Press to exit the setup menu screen.
5 i/k/j/l/ENTER buttons
• Press a i/k/j/l cursor button to select a item.
• Press ENTER to execute or fix the selected item on
the disc menus.
6 TOP MENU button
Press to display the title menu on the DVD.
7 CLEAR button
• Press to clear the MARK memory.
• Press to cancel the wrong track number when
programming tracks on the disc.
8 Numbered buttons
Press to select a track or title directly.
9 MARK button
Press to mark any point in a DVD during a playback.
8
Press to open and close the disc tray.
This player shows On-Screen Display messages on the screen of the TV set to which the DVD player is connected, as well
as those on the display window of the unit.
The On-Screen Display messages, which accompany each operation of the unit, make operation simple and easy especially
when playing DVDs or video CDs. They are also displayed when pressing the ON SCREEN DISPLAY ON /OFF button on
the remote control.
The instructions in this manual refer mainly to the On-Screen Display messages.
1
2
MP3 VCD
@
3 4
5
CD DVD
TITLE
!
1 Operating status indicator
Rotates when loading and playing back a disc.
2 VCD indicator
Lights when a Video CD is loaded.
3 CD indicator
Lights when a CD is loaded.
4 DVD indicator
Lights when a DVD is loaded.
5 TITLE indicator
The title number indicates the number of the title
being played during a DVD playback.
6 CHP/TRK indicator
• The chapter number indicates the number of the
chapter being played during a DVD playback.
• "PBC" is displayed and the CHP/TRK indicator
disappears when a Video CD that supports PBC is
loaded.
• The total number of tracks in stop mode and the
number of the track being played during a playback
are displayed, when a CD or Video CD that does not
support PBC is loaded.
7 PROG. indicator
Lights during a programmed playback.
8 RANDOM indicator
Lights during a random playback.
9 ALL A}B repeat indicator
• }: One track is played back repeatedly.
• ALL}: All tracks on the disc are played back
repeatedly.
• A}B: A desired portion is played back
repeatedly.
6
CHP/TRK
7
PROG.
8
9
RANDOM ALL
A
B
0
0 Time counter
• The total playing time of a Video CD or CD is
displayed during stop mode. (The total playing time
is not displayed when a DVD or MP3 disc is loaded.)
• The elasped time of the chapter or track is displayed.
ANGLE indicator
!
Blinks when a multi-angle scene comes on during a
DVD playback.
@ MP3 indicator
Lights when an MP3 disc is loaded.
9
INTRODUCTION
Display window
CONNECTIONS
At first, decide the outline of the connection among this unit, your TV set and the amplifier, etc. It is necessary to set the
setup menu of this unit according to the connection.
Before connection, identify the type of your audio equipment or of the TV set referring to the following chart. Then decide
the connection and the setup menu according to the types.
Audio system to be connected
Input jack of equipment to be
connected to the DVD player
Referring
Letter
See A.
None (only the television is connected)
Digital input jack
See B.
Analog audio input jacks (L/R)
See C.
An AV amplifier equipped with Dolby Digital
decoder or a Dolby Digital decoder
Digital input jack
See D.
Analog audio input jacks (L/R)
See F.
An AV amplifier equipped with DTS decoder
or a DTS decoder
Digital input jack
See E.
A stereo system or an amplifier
Before making connections
TV SYSTEM SELECT switch
• Connect the AC cords of the unit and external
equipment at the end, after finishing the other
connections.
• Insert the plugs completely into the jacks. Loose
connections may produce a humming sound or other
noise interference.
• When using an optical connection, remove the dust cap
from the DIGITAL OUT (OPTICAL) jack on the rear of
this unit. Keep the cap in store. When not using optical
connections, the dust cap should be in place.
• Refer to the instructions for the connected equipment.
This switch enables you to make use of a TV set which is
NTSC or Multi colour system. The default setting is “PAL”.
DIGITAL OUT
COAXIAL
DIGITAL
OUT
S-VIDEO
OPTICAL
OUT
AUDIO
OUT
L
R
NTSC
PAL AUTO
VIDEO
OUT
NTSC
PAL AUTO
CAUTION
Do not select “DOLBY DIGITAL/PCM or Stream/PCM” in
the “Digital Audio Output” when connecting to an AV
amplifier not equipped with a Dolby Digital decoder or DTS
decoder (with an optical or coaxial connecting cord).
Merely attempting to play a DVD may cause a high level of
noise which could be harmful to your ears and damage
the speakers. In such a case, be sure to select “PCM” in
the “Digital Audio Output”.
NOTES
• When the picture noise appears while copy-protected
DVDs are played, connect the unit directly to a TV set.
Do not connect through a VCR, TV/VCR or AV selector.
• For the speakers and their connection, refer to the
instructions for the AV amplifier.
10
Before turning on the unit;
• Set to “PAL”, when connecting to the TV set of PAL colour
system.
• Set to “AUTO”, when connecting to the TV set of Multi
colour system.
• Set to “NTSC”, when connecting to the TV set of NTSC
colour system.
NOTE
The unit cannot playback DVDs and video CDs that are
recorded in the PAL colour system, if “NTSC” is set.
PREPARATIONS
A Connecting to a TV set only
Rear of TV set
21 pin scart connector
21 pin scart cable (not supplied)
to 21 pin scart connector
Rear of the unit
DIGITAL OUT
DIGITAL
OUT
COAXIAL
AUDIO
OUT
L
S-VIDEO
R
OPTICAL
OUT
NTSC
PAL AUTO
VIDEO
OUT
to an AC power socket
(AC 230 V, 50 Hz)
When your TV set is equipped with an S-video input terminal, see page 17.
Set the setup menu correctly after connecting!
According to the audio equipment and TV set to which the
unit is connected, set the “TV Aspect” of the setup menu
correctly referring to the following below.
See “CHANGING SETUP VALUE” on page 39 in detail.
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not
connect through a VCR, TV/VCR or AV selector.
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letter box
When your TV set is a wide-screen size TV:
16:9 Wide
11
CONNECTIONS (CONTINUED)
B Connecting to a TV set and an amplifier with a Digital In jack
Use either the commercially available optical cord or 75 ohm coaxial cord when connecting this unit to an AV amplifier with
a Digital In jack. The supplied video cord is also available instead of the coaxial cord.
TV set
to 21 pin scart
connector
21 pin scart cable (not supplied)
to 21 pin scart
connector
Rear of the unit
DIGITAL OUT
COAXIAL
DIGITAL
OUT
AUDIO
OUT
L
S-VIDEO
R
OUT
OPTICAL
to DIGITAL OUT
OPTICAL jack
NTSC
PAL AUTO
VIDEO
OUT
to DIGITAL OUT
COAXIAL jack
or Coaxial cord
(not supplied)
to an AC power socket
(AC 230 V, 50 Hz)
Optical cord (not supplied)
to a digital input jack
Front
speaker (L)
Amplifier with a Digital In jack
Front speaker
(R)
When your TV set is equipped with an S-video input terminal, see page 17.
Set the setup menu correctly after connecting!
TV Aspect
According to the audio equipment and TV set to which the
unit is connected, set the “Digital Audio Output” and “TV
Aspect” of the setup menu correctly referring to the
following below.
See “CHANGING SETUP VALUE” on page 39 in detail.
When your TV set is a conventional-screen size TV:
4:3 Letter box
When your TV set is a wide-screen size TV:
16:9 Wide
Digital Audio Output
PCM
12
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not
connect through a VCR, TV/VCR or AV selector.
C Connecting to a TV set and an audio system
PREPARATIONS
TV set
to 21 pin scart
connector
21 pin scart cable (not supplied)
to 21 pin scart connector
AUDIO
OUT
DIGITAL OUT
DIGITAL
OUT
L
COAXIAL
S-VIDEO
R
OPTICAL
NTSC
PAL AUTO
VIDEO
OUT
OUT
white
to AUDIO OUT
L (white)/ R (red) jacks
red
Audio cord (supplied)
to an AC power socket
(AC 230 V, 50 Hz)
to an audio input jacks
(Left/ white, Right/ red)
Audio system
When your TV set is equipped with an S-video input terminal, see page 17.
Set the setup menu correctly after connecting!
According to the audio equipment and TV set to which the
unit is connected, set the “TV Aspect” of the setup menu
correctly referring to the following below.
See “CHANGING SETUP VALUE” on page 39 in detail.
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not
connect through a VCR, TV/VCR or AV selector.
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letter box
When your TV set is a wide-screen size TV:
16:9 Wide
13
CONNECTIONS (CONTINUED)
D Connecting to an AV amplifier equipped with a Dolby Digital (AC-3) decoder
Use either the commercially available optical cord or 75 ohm coaxial cord when connecting this unit to an AV amplifier with
a Digital In jack. The supplied video cord is also available instead of the coaxial cord.
TV set
to 21 pin scart
connector
21 pin scart cable (not supplied)
to 21 pin scart connector
Rear of the unit
AUDIO
OUT
DIGITAL OUT
L
COAXIAL
DIGITAL
OUT
S-VIDEO
R
OPTICAL
to DIGITAL OUT
OPTICAL jack
NTSC
PAL AUTO
VIDEO
OUT
OUT
to DIGITAL OUT
COAXIAL jack
or Coaxial cord
(not supplied)
Optical cord (not supplied)
to an AC power socket (AC
230 V, 50 Hz)
Amplifier equipped with a Dolby
Digital decorder
to a digital input jack
Front
speaker (L)
Front speaker
(R)
Surround speaker (L)
Centre speaker
Subwoofer
Surround speaker (R)
When your TV set is equipped with an S-video input terminal, see page 17.
Set the setup menu correctly after connecting!
According to the audio equipment and TV set to which the
unit is connected, set the “Digital Audio Output” and “TV
Aspect” of the setup menu correctly referring to the following
below.
See “CHANGING SETUP VALUE” on page 39 in detail.
Digital Audio Output
DOLBY DIGITAL/PCM
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letter box
When your TV set is a wide-screen size TV:
16:9 Wide
14
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not
connect through a VCR, TV/VCR or AV selector.
CAUTION
If the AV amplifier is not equipped with a Dolby Digital
decoder, do not select “DOLBY DIGITAL/PCM” in the
“Digital Audio Output” when connecting the AV amplifier
with an optical or coaxial connecting cord.
Merely attempting to play a DVD may cause a high level of
noise which could be harmful to your ears and damage the
speakers. In such a case, be sure to select “PCM” in the
“Digital Audio Output”.
E Connecting to an AV amplifier equipped with a DTS decoder
PREPARATIONS
Use either the commercially available optical cord or 75 ohm coaxial cord when connecting this unit to an AV amplifier with
a Digital In jack. The supplied video cord is also available instead of the coaxial cord.
TV set
to 21 pin scart
connector
21 pin scart cable (not supplied)
to 21 pin scart connector
Rear of the unit
AUDIO
OUT
DIGITAL OUT
L
COAXIAL
DIGITAL
OUT
S-VIDEO
R
OPTICAL
to DIGITAL OUT
OPTICAL jack
NTSC
PAL AUTO
VIDEO
OUT
OUT
to DIGITAL OUT
COAXIAL jack
Optical cord (not supplied)
or Coaxial cord
(not supplied)
to an AC power socket
(AC 230 V, 50 Hz)
Amplifier equipped with a
DTS decorder
to a digital input jack
Front
speaker (L)
Front speaker (R)
Surround speaker (L)
Centre speaker
Subwoofer
Surround speaker (R)
When your TV set is equipped with an S-video input terminal, see page 17.
Set the setup menu correctly after connecting!
According to the audio equipment and TV set to which the
unit is connected, set the “Digital Audio Output” and “TV
Aspect” of the setup menu correctly referring to the following
below.
See “CHANGING SETUP VALUE” on page 39 in detail.
Digital Audio Output
Stream/PCM
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letter box
When your TV set is a wide-screen size TV:
16:9 Wide
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not
connect through a VCR, TV/VCR or AV selector.
CAUTION
If the AV amplifier is not equipped with a DTS decoder, do
not select “Stream/PCM” in the “Digital Audio Output” when
connecting the AV amplifier with an optical or coaxial
connecting cord.
Merely attempting to play a DVD may cause a high level of
noise which could be harmful to your ears and damage the
speakers.In such a case, be sure to select “PCM” in the
“Digital Audio Output”.
15
CONNECTIONS (CONTINUED)
F Connecting to a TV set and an AV amplifier with the Dolby Pro Logic Surround system
TV set
to 21 pin scart
connector
21 pin scart cable (not supplied)
Rear of the unit
DIGITAL OUT
AUDIO
OUT
L
COAXIAL
DIGITAL
OUT
S-VIDEO
R
OUT
OPTICAL
NTSC
PAL AUTO
VIDEO
OUT
to AUDIO OUT
white
L (white)/ R (red) jacks
red
to an AC power socket
(AC 230 V, 50 Hz)
Audio cord (supplied)
to an audio input jacks
Amplifier equipped with
Dolby Pro Logic Surround
(Left/ white, Right/ red)
Front
speaker (L)
Front speaker
(R)
Centre speaker
Surround speaker (L)
Surround speaker (R)
When your TV set is equipped with an S-video input terminal, see page 17.
Set the setup menu correctly after connecting!
According to the audio equipment and TV set to which
the unit is connected, set the “Digital Audio Output” and
“TV Aspect” of the setup menu correctly referring to the
following below.
See “CHANGING SETUP VALUE” on page 39 in detail.
Digital Audio Output
DOLBY DIGITAL/PCM
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letter box
When your TV set is a wide-screen size TV:
16:9 Wide
16
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not connect
through a VCR, TV/VCR or AV selector.
PREPARATIONS
Connecting to a TV set equipped with S-video jack
Rear of TV set
S-video input connector
(S1, S2)
S-video cord
(not supplied)
to S-VIDEO OUT connector
Rear of the unit
DIGITAL OUT
DIGITAL
OUT
COAXIAL
AUDIO
OUT
L
S-VIDEO
R
OPTICAL
OUT
NTSC
PAL AUTO
VIDEO
OUT
to an AC power socket
(AC 230 V, 50 Hz)
Set the setup menu correctly after connecting!
Set the "TV Output Select" and "TV Aspect" of the setup
menu correctly referring to the following below.
See "CHANGING SETUP VALUE" on page 39 in detail.
TV Output Select
S-Video
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letterbox
When your TV set is a wide-screen size TV:
16:9 Wide
NOTE
When the picture noise appears while copy-protected DVDs
are played, connect the unit directly to a TV set. Do not
connect through a VCR, TV/VCR or AV selector.
CAUTION
Do not select "S-Video" when connecting to the TV
set with the 21pin scart cable. Video signals are not
output from the 21pin scart connector of this unit.
17
CONNECTIONS (CONTINUED)
Connecting to a TV set or monitor with video input connector
TV set or monitor
to a video input jacks
(yellow)
to an audio input jacks
(Left/ white, Right/ red)
Yellow
Audio cord (supplied)
Video cord (supplied)
Yellow
White
Red
to AUDIO OUT
to VIDEO OUT
jack (yellow)
Rear of the unit
DIGITAL OUT
DIGITAL
OUT
COAXIAL
L (white)/ R (red) jacks
AUDIO
OUT
L
S-VIDEO
R
OPTICAL
OUT
NTSC
PAL AUTO
VIDEO
OUT
to an AC power socket
(AC 230 V, 50 Hz)
Set the setup menu correctly after connecting!
Set the "TV Aspect" of the setup menu correctly
referring to the following below.
See "CHANGING SETUP VALUE" on page 39 in detail.
TV Aspect
When your TV set is a conventional-screen size TV:
4:3 Letterbox
When your TV set is a wide-screen size TV:
16:9 Wide
18
REMOTE CONTROL
Installing batteries
PREPARATIONS
Detach the battery cover on the rear of the remote control,
and insert two R6 (size AA) batteries with 0 and 9 aligned
correctly.
When to replace the batteries
The maximum operational distance between the remote
control and the sensor of the units should be approximately
7 meters. If this distance decreases, replace the batteries
with new ones.
NOTES
• When operating with the remote control, point the top of
the remote control toward the player.
• If the unit is not going to be used for an extended period
of time, remove the batteries to prevent possible
electrolyte leakage.
• The remote control may not operate correctly when:
- The line of sight between the remote control and the
unit is exposed to intense light, such as direct sunlight
- There is fluorescent lighting near the remote sensor in
the display window.
- Other remote controls are used nearby (those of a TV
set, etc.).
19
PLAYBACK
Getting ready to play
3 2,4
1
i/k/j/l/
ENTER
s
• Turn on the television, and set its video source (Video 1,
Video 2, Video 3, etc.) to the one connected to the DVD
player.
• Turn on the audio device connected to the DVD player.
Set its input source to the one connected to the DVD
player.
1
C
a MENU
Press POWER.
The power comes on, and the 6STANDBY/ON indicator
turns green.
MP3 VCD
2
2,4
a
1
TITLE
CHP/TRK
PROG.
RANDOM ALL
A
B
PROG.
RANDOM ALL
A
B
Press zOPEN / CLOSE.
The disc tray opens.
Numbered
buttons
TOP MENU
i/k/j/l/ENTER
vRETURN
CD DVD
DVD
MP3 VCD
CD DVD
TITLE
CHP/TRK
MENU
c
s
3
Load a disc.
Place a disc in the tray guides (depression), with the label
side facing up. When loading an 8-cm disc, place it in the
inner depression.
4
Press zOPEN / CLOSE.
The disc tray closes, and the DVD player automatically
begins to play the disc.
If the disc does not begin to play, press c.
• If a disc is placed in upside down, “DISC Error” will be
indicated.
About the
CD DVD
DVD
TITLE
CHP/TRK
PROG.
RANDOM ALL
A
B
MP3 VCD
CD DVD
TITLE
CHP/TRK
PROG.
RANDOM ALL
A
B
symbol display
• The
symbol will be displayed on the screen if you
press a button which cannot be used or enter an
incorrect number.
• Some DVD discs may have places where they do
not allow pressing of the STOP, SKIP, or other
buttons. The
mark will be displayed on the screen
if you press a button that is not allowed in such a
place.
20
MP3 VCD
DVD:
Still (Pause)
Video CD with PBC:
MP3 VCD
CD DVD
TITLE
CHP/TRK
PROG.
RANDOM ALL
A
B
To return to normal playback
Press c.
CD/Video CD without PBC:
MP3 VCD
CD DVD
TITLE
BASIC OPERATIONS
Press a during playback.
CHP/TRK
PROG.
RANDOM ALL
A
B
“CD” is displayed when loading a CD.
When the menu screen is displayed
The menu screen may be displayed first after loading a
DVD or VCD which contains a menu.
DVD: Use ikjl to select the program you would like
to view, then press ENTER to begin playback. Press
TOP MENU or MENU to return to the menu screen.
VCD: Use the numbered buttons to select the program
you would like to view.
Press vRETURN to return to the menu screen.
For either DVD or VCDs, menu continuations and the exact
operating procedures for using the menu may vary from
disc to disc. Follow the instructions on the menu screen.
Frame Advance (DVD, VCD)
Press a while the disc is paused.
Each time you press the button, the program advances one
frame. There is no audio when doing Frame Advance.
To return to normal playback
Press c.
Stopping playback
Press s.
When s is pressed during playback, the DVD player
remembers the point at which playback stopped.
To resume play from the point where it stopped
Tips
This unit equips the Playback Control(PBC) On/Off function.
After turning off the PBC, the unit can be play back the
entire Video CD without returning to the menu screen, just
like audio CDs. See "CHANGING SETUP VALUE", page
39.
Press c.
To clear the point to be resumed
Press s again.
When zOPEN/CLOSE is pressed to open the disc tray or
POWER is pressed to turn the power off, the point to be
resumed is also cleared.
To turn the power off
Press POWER. The unit enters the power standby mode,
and the 6STANDBY/ON indicator turns red.
If 8 minutes have elapsed without performing any
operation
The unit enters the standby mode. Therefore, if you start
repeat playback, for example, and leave the unit without
performing any other operation for 8 minutes, the unit
will stop and enter the standby mode.
NOTES
• The disc continues to spin while the menu screen is
displayed even if s is pressed. When you are finished
using the DVD player, turn the power off after pressing
s.
• During a VCD playback with the PBC feature turned on,
resume function does not work.
Performing fast forward, fast reverse, or skipping
operations during VCD playback with PBC on may cause
the DVD player to return to the menu screen.
21
PLAYBACK (CONTINUED)
Skipping
Fast Forward, Reverse
Press g or f on the remote control
during playback.
Each time you press the button, the playback speed
becomes faster as shown below.
DVD:
×2
×4
× 16
× 100
Skip to the next chapter or track: t
The disc position advances one chapter or track each time
the button is pressed.
Return to the previous chapter or track: r
In each disc, pressing r once skips to the beginning of
the chapter (track) currently being played, and pressing
r twice skips to the previous chapter.
NOTE
Video CD:
×2
Press r(r/f) or t(g/t).
×4
When pressing r(r/f) during VCD playback, the
reverse skipping playback only skips to the beginning of
the track currently being played.
×8
The playback speed is fixed to ×2 during playback of CDs.
To skip to the desired chapter or track directly using
the remote control (VCD without PBC/CD)
To return to normal playback
When stopped or during playback, enter the desired track
number using the numbered buttons on the remote control.
Example: To play track 3
Press 3 on the remote control.
Example: To play track 20
Press 2, 0 on the remote control.
Press c .
NOTES
• There is no audio during DVD or Video CD playback.
• The search speed is the value of a disc which has an
average bit rate. In some discs, the speed displayed on
the display window may be different from the actual speed.
Slow Playback (DVD/VCD)
Press F.SLOW or B.SLOW during playback.
The playback speed changes each time the button is
pressed, as shown below.
DVD Slow Playback
× 1/16
× 1/8
× 1/4
× 1/2
Video CD Slow Playback
- F.SLOW × 1/16
× 1/8
× 1/4
To return to normal playback
Press c.
NOTES
• The B.SLOW playback does not work during VCDs
playback.
• There is no audio during slow playback.
• Subtitles do not appear on the TV screen during slow
playback.
22
Playback begins at the beginning of the selected track.
General playback status can be displayed on the TV
screen. Some items only show the indicated information.
Other items allow the settings to be changed.
1
Press ON SCREEN DISPLAY ON/OFF
during playback.
2
Press i/k to select the desired item.
The currently selected item is indicated by a yellow frame
on its OSD menu.
3
2,3
c
When numbers are displayed (e.g. title NO.), the number
buttons can also be used for setting instead of j/l.
For some functions, the setting will be registered
immediately; for others, ENTER must be pressed.
g
1
t
r
Press j/l to select the desired
setting.
To clear the OSD Menu
f
Press ON SCREEN DISPLAY ON/OFF.
NOTE
If no button is pressed for 10 seconds, the OSD menu
disappear.
Examples of On Screen Display (OSD) menu
(The OSD menu may differ depending on the disc contents.)
DVD:
1
1
0:16:57
CD/Video CD without PBC:
1 ENG
D
6 CH
1
OFF
16:57
STER.
1
STER.
NORM.
NORM.
16:57
NORM.
Video CD with PBC:
23
BASIC OPERATIONS
On Screen Display (OSD) menu
PLAYBACK (CONTINUED)
Detailed description of each OSD menu
< DVD OSD>
Function
Selection method
Items
(Press i/k to select desired item)
To show the current title No.
and to skip to the desired title No.
j/l, or Number
ENTER
1
To show the current chapter No.
and to skip to the desired chapter No.
j/l, or Number
ENTER
r/t
1
To show the elapsed time
and directly select scenes by the
elapsed time.
Number
ENTER
To show the current audio soundtrack
language, encoding method, channel No.
and to change the settings.
j/l,
AUDIO SELECT
To show the current subtitle language
and to change the setting.
j/l,
SUBTITLE SELECT
To show the current angle No.
and to change the angle.
j/l,
ANGLE
To show the current sound (NORMAL or
3D SURROUND)
and to change the setting.
j/l,
SURROUND
0:16:57
1 ENG
D
6 CH
OFF
1
NORM.
< VCD/CD OSD >
Function
Selection method
Items
(Press i/k to select desired item)
To show the current track No.
and to skip to the desired track No.
r/t,
j/l, or Number
ENTER
To show the elapsed time.
(Display only)
16:57
To show the current audio (STEREO,
LEFT, RIGHT)
and to select to the desired audio
channel.
j/l,
AUDIO SELECT
To show the current sound (NORMAL or
3D SURROUND)
and to change the setting.
j/l,
SURROUND
NOTE
Some discs may not provide all of the above OSD menu.
24
1
STER.
NORM.
SEARCH
1
Press ON SCREEN DISPLAY ON/OFF,
either while playing or when stopped.
Go to step 3, if you press it while a DVD disc stops.
Numbered
buttons
CLEAR
2,3,4
2
Press i or k to select “TITLE” or
“TRACK”.
1
1
3
Press j or l to enter the desired
title or track number.
3
• Numbered button is also available to select the desired
title number.
How to enter numbers
Example:
This DVD player provides three types of DVD searches.
Example:
to play title number 2
Press 2.
to play title number 10
Press 1, 0.
Title search
Specify a title number.
To use this feature with Video CDs that support PBC, turn
off PBC first. (See"CHANGING SETUP VALUE" on page
39.)
Chapter search
Specify a chapter number.
If you enter the wrong number
Press CLEAR to remove the number you entered. Then
enter the correct number.
4
Press ENTER.
Playback begins with the specified title or track.
Time search
Specify the elapsed time of the desired location.
NOTE
If no button is pressed for 10 seconds, the OSD menu
disappears.
25
MORE FEATURES
Title search (DVD)/Track search (VCD
without PBC/CD)
SEARCH (CONTINUED)
Chapter search (DVD)
Time search (DVD)
1
Press ON SCREEN DISPLAY ON/OFF
during playback.
With a DVD which allows displaying of elapsed time, you
can specify a time on the disc to search for a desired
location.
2
Press i or k to select “CHAPTER”.
1
Press ON SCREEN DISPLAY ON/OFF
during playback.
2
Press i or k to select “TIME”.
1
3
-:--:-Press j or l to enter the desired
chapter number.
3
3
Use the numbered buttons to enter the
time of the desired location.
• Numbered button is also available to select the desired
chapter number.
1:17:30
How to enter numbers
Example:
to play chapter number 17
Press 1, 7.
How to enter numbers
Example:
If you enter the wrong number
Press CLEAR to remove the number you entered. Then
enter the correct number.
Example:
4
start play at 1 hour, 17 minutes, 30 seconds
(1:17:30)
Press 1(hour), 1,7 (minutes), then 3, 0
(seconds).
start play at 8 minutes 7 seconds (0:08:07)
Press 8 (minutes), then 0, 7 (seconds).
Press ENTER.
Playback begins with the specified chapter.
NOTE
Chapter search will not work if you specify a chapter number
which does not exist on the disc.
If you enter the wrong numbers
Press CLEAR several times to remove the numbers you
entered. Then enter the correct numbers.
4
Press ENTER.
Playback begins at the specified location (time).
NOTES
• Time search does not work if you specify a time greater
than the length of the disc.
• Time search may not work with some discs even if they
are capable of elapsed time.
26
Mark search (DVD)
Up to 5 points can be memorized within the same title
number.
MARK
MARK SEARCH
To memorize a desired point, press MARK during
playback.
CLEAR
i/k/j/l/
ENTER
1/5
c
“Marker 1/5” is displayed and memorized.
Each time you press MARK, the desired points are
memorized.
Restarting play from the memorized point
1
Press MARK SEARCH either while
playing or when stopped.
MARKED
PICTURE 1
MARKED
PICTURE 2
MARKED
PICTURE 4
MARKED
PICTURE 5
MARKED
PICTURE 3
* PRESENT
PICTURE
*The current picture being played is displayed.
NOTES
• Mark search may not work on multi-angle scenes or
subtitles recorded portions.
• All the marked pictures are cleared when the power is
turned off or the disc is removed.
• When skipping or changing to an other title number, all of
the memorized points are cleared.
2
Press i /k /j /l to select the
marked picture to be restarted.
3
Press c or ENTER.
Play resumes from the point corresponding to the selected
marked picture.
To clear the memorized point, press i/k/j/l to select
the marked picture then press CLEAR.
The “PRESENT PICTURE” is not cleared.
27
MORE FEATURES
Playback can restart from a memorized point.
ZOOMING AND CHANGING THE ANGLE
Changing the angle (DVD)
ZOOM
ANGLE
When playing a DVD which has been recorded in multiangle (photographed from several different angles), you can
select which angle you would like to view the action from.
When a multi-angle scene comes on during playback,
“ANGLE” will blink in the display window to let you know
that you can change the angle.
i/k/j/l/
ENTER
1
Press
ANGLE during playback.
Number of angle being played back.
1
2
Press
ANGLE repeatedly until the
desired angle is selected.
2
Zoom function (DVD)
This function allows you to Zoom-in and enlarge the picture
to either 4 times or 16 times.
1
Press ZOOM during playback or Still
playback.
The zoom area changes each time the button is pressed,
as shown below.
NORMAL
×4
×16
To move the zoom area, press i/k/j/l.
2
Press ENTER.
The selected zoom area is displayed in full size on the TV
screen.
To return to the normal playback, press ZOOM
repeatedly.
NOTES
• Some DVDs may not respond to Zoom function.
• Zoom function may not work on multi-angle scenes.
28
symbol will be displayed if you press ANGLE while
viewing a disc which does not have multiple viewing
angles, or if viewing a part of the disc which does not
allow angle selection.
RANDOM AND REPEAT PLAYBACK
Press REPEAT during playback.
REPEAT
A-B
The repeat mode will change each time you press REPEAT.
CHAPTER:
Repeat of the chapter being played.
RANDOM
r
CHAPT
t
TITLE: Repeat of the title being played.
TITLE
OFF: Cancel repeat mode. (Normal playback)
Random playback (Karaoke DVD/CD )
OFF
NOTES
• This function only works with DVD Karaoke discs and
audio CDs.
• Video CDs that are not equipped with PBC only allow
Random playback as well as audio CDs.
To turn off the PBC, see page 39.
Press RANDOM either while playing or
when stopped.
NOTES
• Title and Chapter repeat playback will be cancelled, when
changing a title or chapter by pressing t,g, r or
f.
• Title and Chapter repeat playback will be cancelled, when
the DVD player is stopped.
The DVD player automatically begins Random Playback
and "RANDOM" indicator turns on.
By pressing r (r /f )or t (g /t ) during
Random playback, the DVD player selects another title
(track) and begins Random Playback.
To resume normal playback
Press RANDOM. "RANDOM" indicator turns off.
29
MORE FEATURES
Repeat playback (DVD)
RANDOM AND REPEAT PLAYBACK (CONTINUED)
Repeat playback (VCD without PBC/CD)
Repeating a portion between two
specified points (A-B Repeat)
Press REPEAT during playback.
The repeat mode will change each time you press REPEAT.
TRACK:
Repeat of the track being played.
Allows you to select a portion of a track to be repeated.
The portion to be repeated may not span a track boundary,
but must be within a single track.
1
TRACK
During playback, press A-B at the
starting point of the section you want
to repeat.
A
*
ALL:
Repeat of all tracks on a disc being played.
ALL
2
Press A-B again at the ending point
of the section you want to repeat.
The player returns to point A and plays the section between
A and B.
A
OFF:
Cancel repeat mode. (Normal playback)
OFF
B
To return to the normal playback
Press A-B again during playback.
OFF
ALL and TRACK cannot be used during menu playback
with a video CD (when using the PBC feature).
To turn off the PBC, see page 39.
NOTES
• TRACK repeat playback will be cancelled, when changing
a track by pressing t(g) or r(f).
• All repeat playback will be cancelled, when the DVD
player is stopped.
30
NOTE
During a multi-angle scene, the unit may play the different
scene that you memoried by pressing A-B button.
PROGRAMMED PLAYBACK
the numbered buttons to select
2 Press
the desired track number.
2,3,4
3,4,5
r
Step
1
Total Time 03:58
1
REPEAT
MORE FEATURES
Program
1
CLEAR
t
Clear All
3
Press l and press the numbered
buttons to select the desired track
number.
Program
1
5
19
Step
3
Total Time 08:32
Clear All
With video and audio CDs, you can select the tracks you
would like to play, and play them in any order. You can
specify up to 20 tracks.
To use this feature with Video CDs that support PBC, turn
off PBC first. (See"CHANGING SETUP VALUE" on page
39.)
4
5
Repeat step 3.
Press ENTER to start playback.
The selected tracks are stored in the memory and play now
begins in the programmed sequence.
After playback
Programmed playback is stopped.
1
Press PROGRAM either while playing
or when stopped.
The program menu screen appears on the TV screen.
Program
Step
1
Total Time 00:00
To play the programmed playback repeatedly
1 Follow all the above steps of "Programmed playback"
to program tracks.
2 Press REPEAT.
The programmed tracks are played repeatedly.
To skip tracks
Press r or t repeatedly. Playback skips to the
previous or succeeding tracks within the program.
To delete a track from the program
Clear All
• To exit the screen, press PROGRAM.
Press i/k/j/l to select the unwanted track and press
CLEAR.
To clear all the programs
1 Press i/k/j/l to select the “Clear All” and press
ENTER.
2 Press ENTER again.
(The programs are also cleared when the disc is
removed.)
31
CREATING A 3D SURROUND EFFECT
SURROUND
The DVD player can produce a 3D Surround effect, using
SpatializerTM N-2-2TM technology, which simulates multichannel audio playback from two conventional stereo
speakers, instead of the five or more speakers normally
required to listen to multi-channel audio from a home theater
system. This feature works with DVD discs encoded with
Dolby Pro Logic, Dolby Digital (AC-3).
1
Press SURROUND during playback.
Each time this button is pressed, the TV screen display
changes:
NORM.
2
Press SURROUND repeatedly until the
desired sound is selected.
3D SUR
NOTES
• This 3D Surround effect may not be available on some
DVD discs, such as those recorded with a mono audio
soundtrack.
• Turn off the TV surround sound and other surround effects
when using this 3D surround effect.
• For best 3D Surround effect using only two speakers it is
recommended that the two speakers be positioned
approximately 2m to 2.5m apart, and the listening position
should be 2m to 2.5m away from the speakers.
• Do not press SURROUND while recording the music. The
sound signals which come from this unit are intermitted.
32
CHANGING THE AUDIO TRACK
Changing audio tracks (DVD)
AUDIO SELECT
1
Press AUDIO SELECT during playback.
Number of the audio soundtrack language being played
back is displayed.
1 ENG
D
6 CH
2
Press AUDIO SELECT repeatedly until
the desired language is selected.
2 FRE
D
6 CH
• When playing a DVD with soundtracks in multiple
languages, the audio will automatically be played in
the language which was selected when the DVD
player was set up. If there is not a soundtrack in
that language on the disc, the disc will determine
which audio track is played.
• The audio track may only be changed for discs which
contain multiple audio tracks.
• The number of audio tracks available differs from
disc to disc.
Changing audio tracks (VCD/CD)
1
Press AUDIO SELECT during playback.
STER.
2
Press AUDIO SELECT repeatedly until
the desired sound is selected.
Each time you press the button, the display changes as
follows.
STEREO
LEFT
RIGHT
LEFT
33
MORE FEATURES
Some discs have more than one audio track, such as
soundtracks with different languages. While playing such
a disc, the audio track can be changed to hear the different
soundtracks.
DISPLAYING AND CHANGING SUBTITLES
When playing DVD discs which contain subtitles, you can
display the subtitles on the screen or change the language
of the subtitles.
1
SUBTITLE
SELECT
Press SUBTITLE SELECT during
playback.
When no subtitles are recorded, “OFF” will be displayed
instead of the language number.
OFF
2
Press repeatedly SUBTITLE SELECT
until the desired language is
selected.
Number of the subtitle language being played back is
displayed.
1 ENG
• The
symbol will be displayed if you try to show
subtitles with a disc which does not contain them.
• The first subtitles displayed will be in the subtitle
language selected with the subtitle setting (see page
39). If there are no subtitles in that language on the
disc, the disc will determine which subtitles are
shown.
• Subtitles may only be changed with discs which
contain more than one set of subtitles.
• The number of subtitle languages varies from disc
to disc.
• With some discs, it may take a few moments after
you press SUBTITLE SELECT for the new subtitles
to be displayed.
34
To eliminate the On Screen Subtitles.
Press SUBTITLE SELECT repeatedly to select OFF at step
2.
NOTE
When a disc supporting the closed caption is played, the
subtitle and the closed caption may overlap each other on
the TV screen. In this case, turn the subtitle off.
PLAYING BACK AN MP3 DISC
The DVD player can play back MP3 recorded on a CDROM, CD-R or CD-RW discs.
Before playing back an MP3 disc, read the following notes.
Glossary
Notes on MP3 disc
About MP3
• An MP3 file is audio data compressed by using MPEG1,
the audio layer-3 file-coding scheme. We call files which
have the ".mp3" extension "MP3 files".
• The unit cannot read an MP3 file which has a file
extension other than ".mp3".
•
is displayed on the MP3 menu if a non-MP3 file was
included in a directory or folder.
• Noises may be heard if you play a non-MP3 file that has
the ".mp3" extension.
An extension is the last three characters which divide a file
name by period. The extension shows the attribution of the
file.
The extension of the MP3 file is "mp3".
Session:
A session is one section on a disc between the beginning
of written data and the end of written data.
A multi-session disc is a disc which has more than two
sessions.
The restriction of playing back MP3
• This unit can recognize up to 256 including files and
folders per disc. A disc recorded with more than 256
cannot be played, including files and folders.
• The maximum allowable depth of nested folder is 50,
including files.
• The unit may not play MP3 files in the order that you
recorded them on the disc.
• The unit plays only the first session with a multi session
disc.
• The unit plays only audio tracks if a disc contains both
audio tracks and MP3 files.
• It may take over 30 seconds to read the MP3 files,
depending on the complexity of the folder tree.
The limitation of indications
• Up to 14 characters are displayed for the name of a
folder or track.
• Characters other than uppercase letters ("A" to "Z"),
numerals ("0" to "9") and underscore ("_") may not be
displayed, or may be displayed in different characters.
• The elapsed playing time on the display window may
not be correct when playing MP3 files.
• Depending on the condition of the recording equipment
or the CD-R/RW disc itself, a false folder or file which
cannot be played on this unit is displayed on TV screen.
Tips on recording MP3
• Enjoying high quality sound, we recommend to
convert to MP3 files with a sampling frequency of
44.1kHz and a fixed bit rate of 128 kbps.
To playback MP3 files in the order that you recorded
1 Writing software which is capable of recording MP3
files in numerical and alphabetical order is required.
2 Include a two or three digit number at the beginning
of each file name. (e.g."01","02", ... or "001", "002", ...)
3 It's recommended that you use only the root folder
(do not create child folder under the root folder).
35
MORE FEATURES
Extension:
PLAYING BACK AN MP3 DISC (CONTINUED)
2
Press i/k to select the album with
the track that you want to play back.
MP3
Program
MP3-1
..
TRACK_1
TRACK_2
TRACK_3
TRACK_4
MENU
TOP MENU
TRACK_5
2,3,4
4
vRETURN
a
t
r
TRACK_6
TRACK_7
TRACK_8
Clear All
To return to the previous MP3 menu
Press vRETURN.
s
To move to the first MP3 menu
Press MENU.
3
Press ENTER and Press i/k to select
the desired track.
MP3
Program
MP3-1
..
From the following explanations, we refer to what are called
"MP3 file" and "folder" in PC terminology as "track" and
"album", respectively.
TRACK_1
TRACK_2
TRACK_3
TRACK_4
TRACK_5
TRACK_6
TRACK_7
TRACK_8
Playing back with MP3
1
Load an MP3 disc.
To return to the top of page within the album
Press TOP MENU.
Pressing TOP MENU repeatedly, the pages within the
album will change by turns.
The MP3 menu is displayed.
MP3
Clear All
Program
MP3-1
4
MP3-2
MP3-3
MP3-4
MP3-5
Press ENTER or c .
Playback starts and will stop after playing back all of the
tracks within the album.
MP3-6
MP3-7
MP3-8
MP3-9
Clear All
To skip to the desired track during playback
NOTES
• It may take over 30 seconds to read the MP3 files,
depending on the complexity of the folder tree.
• If you press vRETURN, MENU or TOP MENU during
playback, the playback stops.
Press t or r repeatedly during playback.
Or press i/k to select the desired track and press ENTER.
Playback skips to the desired track within the album.
To stop playback
Press s.
To pause playback
Press a during playback. To return to play back, Press
c.
36
REPEAT
Press PROGRAM to list the selected
track on MP3 Program list.
Repeat step 2 to 3 to select tracks within the album or select
another track in an other album.
MP3
Program
MP3-1
CLEAR
..
PROGRAM
TOP MENU
TRACK_2
TRACK_7
TRACK_1
TRACK_6
TRACK_2
TRACK_9
Program
list
TRACK_3
i/k/j/l/
ENTER
TRACK_4
TRACK_5
TRACK_6
TRACK_7
t
r
TRACK_8
Clear All
To check the order of programmed tracks
Press l. Then press TOP MENU.
The program lists will change by turns when more than 9
tracks are selected. Press j after checking.
4
Press l to select the desired track.
Then press ENTER or c to start.
Playback begins in the listed sequence.
MP3
NOTE
Program
MP3-1
..
Comparing with Audio CD operations , the following
playback and functions do not work when playing back an
MP3 disc.
• Fast forward g, Fast reverse f, Random and A-B
Repeat playback.
• OSD menu, Resume, Surround and Selecting audio
track function.
Programmed playback with MP3
Up to 60 tracks per disc can be programmed.
1
Follow step 1 to 2 on previous page.
2
Press i/k to select a track.
TRACK_2
TRACK_7
TRACK_1
TRACK_6
TRACK_2
TRACK_9
TRACK_3
TRACK_4
TRACK_5
TRACK_6
TRACK_7
TRACK_8
Clear All
Playback stops after playing back all of the listed tracks on
the MP3 Program list.
To clear the programs one by one
Press i/k to delete the track on the MP3 Program list
and then press CLEAR.
To clear all the programs
MP3
Press i/k to select "Clear All"on the MP3 Program list
and then press ENTER.
The programs are also cleared when the disc is removed.
Program
MP3-1
To return to the normal playback
..
Press j. Then select a desired track or an album.
TRACK_1
TRACK_2
TRACK_3
NOTES
TRACK_4
TRACK_5
TRACK_6
TRACK_7
TRACK_8
Clear All
• vRETURN and MENU buttons do not work during
programmed playback.
• If you press TOP MENU repeatedly during programmed
playback, the playback begins at the first track on each
page of the program list.
37
MORE FEATURES
3
PLAYING BACK AN MP3 DISC (CONTINUED)
To play back a programmed track repeatedly
Repeat playback with MP3
Press REPEAT once during programmed playback.
The current track will be played back repeatedly.
To play back a track repeatedly
Press REPEAT once during playback.
The current track will be played back repeatedly.
MP3
Program
MP3-1
..
MP3
Program
MP3-1
TRACK_2
TRACK_7
TRACK_1
TRACK_6
TRACK_2
TRACK_9
TRACK_3
..
TRACK_4
TRACK_1
TRACK_5
TRACK_2
TRACK_6
TRACK_3
TRACK_7
TRACK_4
TRACK_8
TRACK_5
Clear All
Repeat
symbol
TRACK_6
TRACK_7
TRACK_8
Clear All
To play back all of the listed tracks repeatedly
Press REPEAT twice during programmed playback.
All of the listed tracks on the MP3 Program list will be
played back repeatedly.
To play back an entire album repeatedly
Press REPEAT twice during playback.
All of the tracks wihtin the album will be played
back repeatedly.
MP3
MP3
Program
MP3-1
..
TRACK_2
TRACK_7
TRACK_1
TRACK_6
TRACK_2
TRACK_9
TRACK_3
Program
TRACK_4
MP3-1
TRACK_5
..
TRACK_6
TRACK_1
TRACK_7
TRACK_2
TRACK_8
TRACK_3
Clear All
TRACK_4
TRACK_5
TRACK_6
To cancel repeat playback
TRACK_7
TRACK_8
Clear All
Press REPEAT repeatedly until the Repeat symbol turns
off.
NOTE
Repeat playback with a track will be cancelled when
pressing i/k, r or t .
38
Disc Audio*
Sets the audio soundtrack language.
Disc Subtitle*
Sets the subtitle language .
Disc Menu*
Sets the language used in the menu screen.
2,3
1
vRETURN
* If the language selected by these settings does not exist
on the disc, the disc's default language is used.
Rating
When playing discs with preset restriction level
encoding, this setting allows the unit to
automatically cut scenes of excessive violence, etc.
Password
Sets the password to prevent children from changing
the restriction level.
TV Aspect
Sets the aspect ratio of the televison set to which
the unit is connected.
Menu Language
Sets the language on this setup menu.
Your DVD player comes from the factory with all the
basic items set properly.
• Check the “Digital Audio Output” and “TV Aspect”
settings to make sure they are correct for the type of
equipment connected to your DVD player. For more
information, please refer to the “Connections” section,
which begins on page 10.
• Change any other settings according to your individual
setup and preferences.
Basic operations
1
Press SETUP either while playing or
when stopped.
The setup menu is displayed.
TV Output Select
Selects the video output jacks to be output video signals.
CAUTION
Do not select "S-Video" when connecting to the
TV set with the 21pin scart cable. Video signals
are not output from the 21pin scart connector of
this unit.
Others
Sets the Pseudo PAL and PlayBack Control(PBC)
function On/Off.
Digital Audio Output
Sets the digital audio output to be output from the
unit according to the type of audio equipment
connected to the unit.
3
Press l and then i/k to select the
desired setting and press ENTER.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
To exit SETUP menu
TV Output Select
Polish
Press SETUP or vRETURN.
Others
Hungarian
Digital Audio Output
Russian
• Some items require additional steps.
Other – – – –
39
AS NECESSARY
CHANGING SETUP VALUES
2 Press i/k to select the desired item.
CHANGING SETUP VALUES (CONTINUED)
Disc Audio
The audio sound track language on a DVD disc can be
changed. If the language selected is not available on
the disc, the original language designated by each
disc will be selected.
Numbered
buttons
CLEAR
1
i/k/j/l/
ENTER
SETUP
At the SETUP menu, press i/k to
select “Disc Audio” and press l.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
TV Output Select
Polish
Others
Hungarian
Digital Audio Output
Russian
Other – – – –
2
Press i/k to select the desired
language and press ENTER.
Original :
English :
French :
German :
Spanish :
Italian :
Chinese :
Polish :
Hungarian :
Russian :
Other :
40
The original language of each
disc will be selected.
The English will be selected.
The French will be selected.
The German will be selected.
The Spanish will be selected.
The Italian will be selected.
The Chinese will be selected.
The Polish will be selected.
The Hungarian will be selected.
The Russian will be selected.
Another language can be
selected. You can input a 4-digit
language code. (Refer to the
language codes on page 47.
Press CLEAR if an incorrect
language code is entered.)
Rating
The subtitle language on a DVD disc can be changed.
If the language selected is not available on the disc,
the original language designated by each disc will be
selected.
1
2
At the SETUP menu, press i/k to
select “Disc Subtitle” and press l.
1
At the SETUP menu, press i/k to
select “Rating” and press l.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
Disc Audio
8
TV Aspect
Italian
Disc Subtitle
7
Menu Language
Chinese
Disc Menu
6
TV Output Select
Polish
Rating
5
Others
Hungarian
Password
4
Digital Audio Output
Russian
TV Aspect
3
Other – – – –
Menu Language
2
TV Output Select
Others
1
2
The language used in the DVD menu can be changed.
If the language selected is not available on the disc,
the original language designated by each disc will be
selected.
At the SETUP menu, press i/k to
select “Disc Menu” and press l.
Unlock
Digital Audio Output
Press i/k to select the desired
language and press ENTER.
Disc Menu
1
Some DVD discs contain a restriction level which enables
parents to remove scenes or prevent playback of discs by
children. The unit is equipped with a password designed to
prevent children changing the level.
Press i/k to select the desired level
and press ENTER.
Disc Audio
8 Blocked
Disc Subtitle
7 Blocked
Disc Menu
6
Rating
5
Password
4
TV Aspect
3
Menu Language
2
TV Output Select
Others
1
Unlock
Digital Audio Output
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
TV Output Select
Others
Polish
Digital Audio Output
Russian
Hungarian
Other – – – –
2
You cannot play DVD discs rated higher than the level you
selected unless you cancel the parental lock function.
For example, when you select level 6, discs rated higher
than level 6 are blocked and cannot be played.
Press i/k to select the desired
language and press ENTER.
The parent lock level is equivalent to the following USA
movie ratings.
Example
Level 7: NC-17
Level 3: PG
Level 6: R
Level 1: G
Level 4: PG 13
The password (4-digit) can be set not to change the Rating
easily. After setting the password, the Rating can not be
changed unless you input the password.
Refer to the Password on page 42.
41
AS NECESSARY
Disc Subtitle
CHANGING SETUP VALUES (CONTINUED)
Setting is finished and the SETUP menu is displayed.
Password
A 4-digit password can be set to prevent playback of discs
with higher ratings.
Disc Audio
Change
Disc Subtitle
Clear
Disc Menu
Rating
1
Password
At the SETUP menu, press i/k to
select “Password” and press l.
Disc Audio
NEW
Disc Subtitle
––––
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
Disc Menu
Rating
Password
TV Aspect
The rating is locked. Any discs whose rating is higher than
the setting cannot be played back unless the correct
password is entered.
Menu Language
TV Output Select
Others
Digital Audio Output
To change the settings
2
Input a 4-digit password using the
numbered buttons, then press ENTER.
Example : 1234
Do not forget your password.
Disc Audio
To change the rating level, enter your 4-digit password and
follow the steps on page 41 again.
To change the password
1 At the SETUP menu, select “Password” and press l.
2 Input the 4-digit password and press ENTER.
3 Select “Change” and press ENTER.
4 Follow step 2 to 3 on the left.
NEW
Disc Subtitle
To clear the password
1 At the SETUP menu, select “Password” and press l.
2 Input the 4-digit password and press ENTER.
3 Select “Clear” and press ENTER.
Disc Menu
Rating
Password
TV Aspect
Menu Language
TV Output Select
Others
When you forget your 4-digit password
If you forget your password, follow the procedure below.
Digital Audio Output
3
Input the 4-digit password again to
verify, then press ENTER.
Disc Audio
Disc Subtitle
Disc Menu
Rating
Password
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
42
Verify
1 At the SETUP menu, select “Password”.
2 Enter the 6-digit number “210499” and then press
ENTER.
The 4-digit password is cleared.
Select the appropriate screen type according to your TV
set; conventional size screen (4:3) or wide-screen (16:9).
1
Cut off
At the SETUP menu, press i/k to
select “TV Aspect” and press l.
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Media recorded in wide (16:9) format will
be played at the full screen height, with
the left and right portions cut off, for media
which contains pan-scan encoding. Other
media will be played in “letterbox” style.
Rating
Password
4:3 Panscan
TV Aspect
Menu Language
TV Output Select
Others
16:9 Wide :
Digital Audio Output
2
Press i/k to select the desired
Aspect and press ENTER.
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Select when a wide-screen TV set is
connected.
Played in “FULL” size. (Setting the widescreen TV to “FULL” mode is also
necessary.)
Rating
Password
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
16:9 Wide
*Each screen shows an example when the video
material for a wide-screen is played.
(This setting does not affect the video material for
conventional size.)
4:3 Letterbox : Setect when a conventional TV set is
connected. Media recorded in wide (16:9)
format will be played in “letterbox” style,
with black bands at the top and bottom of
the screen.
4:3 Letterbox
43
AS NECESSARY
4:3 Panscan :
TV Aspect
CHANGING SETUP VALUES (CONTINUED)
Menu Language
The language used in this SETUP menu can be changed.
1
At the SETUP menu, press i/k to
select “Menu Language” and press
l.
i/k/j/l/
ENTER
SETUP
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
German
Password
Italian
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
2
Press i/k to select the desired
language and press ENTER.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
German
Password
Italian
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
English :
Spanish :
French :
German :
Italian :
44
The
The
The
The
The
setup
setup
setup
setup
setup
menu
menu
menu
menu
menu
is
is
is
is
is
displayed
displayed
displayed
displayed
displayed
in
in
in
in
in
English.
Spanish.
French.
German.
Italian.
Others (Pseudo PAL/PBC)
Select “S-Video” when connecting to a TV set with an S-Video
cord.
CAUTION
Do not select "S-Video" when connecting to the
TV set with the 21pin scart cable. Video signals
are not output from the 21pin scart connector of
this unit.
The Pseudo PAL and Playback Control settings(PBC)
can be changed.
1
At the SETUP menu, press i/k to
select “Others” and press l.
Disc Audio
Pseudo PAL On
Disc Subtitle
Pseudo PAL On
Disc Menu
1
At the SETUP menu, press i/k to
select “TV Output Select” and press l.
Disc Audio
S-Video
Disc Subtitle
SCART R-G-B
Rating
PBC On
Password
PBC Off
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
Disc Menu
Rating
Password
TV Aspect
Menu Language
TV Output Select
Others
2
Press i/k to select the desired
items and press ENTER.
Digital Audio Output
Pseudo PAL settings
2
Press i/k to select the desired
items and press ENTER.
Pseudo PAL On:
A NTSC DVD disc can be played back with the PAL colour
system TV set, depending on the disc.
Pseudo PAL Off:
A NTSC DVD disc cannot be played back with the PAL
colour system TV set.
Video output settings
S-Video:
Video signals are output from the S-VIDEO OUT jack on
the unit.
SCART R-G-B:
Video signals are output from the 21-pin scart connector
on the unit.
NOTE
Video signals are always output from the VIDEO OUT
jack on the unit regardless of these settings.
NOTE
The Pseudo PAL function only works when TV SYSTEM
SELECT switch on the rear panel is set to “PAL”.
PlayBack Control (PBC) settings
PBC On:
Video CDs are played back according to the PBC.
PBC Off:
Video CDs can be played back in the same way as
Audio CDs.
45
AS NECESSARY
TV Output Select
CHANGING SETUP VALUES (CONTINUED)
DOLBY DIGITAL/PCM:
Digital Audio Output
Each DVD disc has a variety of audio output options. Set
the player’s Digital Audio Output according to the type of
audio system you use.
CAUTION
If the AV amplifier is not equipped with a Dolby
Digital decoder or DTS decoder, do not select
“DOLBY DIGITAL/PCM or Stream/PCM” in the
“Digital Audio Output” when connecting the AV
amplifier with an optical or coaxial connecting
cord.
Select this when connecting to an AV amplifier or other
equipment that is equipped with a Dolby Digital (AC-3)
decoder or a Dolby Pro Logic Surround decoder.
Stream/PCM:
Select this when connecting to an AV amplifier or other
equipment that is equipped with a DTS decoder or a MPEG
decoder.
PCM:
The default setting is “PCM”. Select this when connecting
to an audio system without a Dolby digital(AC-3), DTS or
other special decoder.
Merely attempting to play a DVD may cause a high
level of noise which could be harmful to your ears and
damage the speakers. In such a case, be sure to select
“PCM”.
OUTPUT
Playback Disc Stream/PCM
1
At the SETUP menu, press i/k to
select “Digital Audio Output” and
press l.
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Rating
Password
TV Aspect
96kHz Linear
PCM DVD
PCM
PCM
PCM
DTS DVD
DTS bit Stream
Not Output
Not Output
Dolby Digital
DVD
Dolby Digital bit Dolby Digital
bit Stream
Stream
PCM
MPEG DVD
MPEG bit Stream PCM
PCM
Audio CD/
Video CD
PCM
PCM
PCM
DTS bit Stream
DTS bit
Stream
DTS Audio CD DTS bit Stream
Menu Language
DOLBY DIGITAL/ PCM
PCM
TV Output Select
Others
Digital Audio Output
NOTE
2
When you are not using the player’s digital audio output,
don’t select any of the options.
Press i/k to select the desired
output and press ENTER.
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
Rating
Password
TV Aspect
Menu Language
TV Output Select
Others
Digital Audio Output
46
/PCM
Code
6565
6566
6570
6577
6582
6583
6588
6590
6665
Language
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Code
7285
7289
7365
7378
7383
7384
7387
7465
7473
Language
Hungarian
Armenian
Interlingua
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Code
8084
8185
8277
8279
8285
8365
8368
8372
8373
Language
Portuguese
Quechua
Rhaeto-Romance
Romanian
Russian
Sanskrit
Sindhi
Serbo-Croatian
Singhalese
6669
6671
6672
6678
6679
6682
6765
6779
6783
6789
6865
6869
6890
6976
6978
6979
6983
6984
6985
7065
7073
7074
7079
7082
7089
7165
7168
7176
7178
7185
7265
7273
7282
Byelorussian
Bulgarian
Bihari
Bengali; Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
7487
7565
7575
7576
7577
7578
7579
7583
7585
7589
7665
7678
7679
7684
7686
7771
7773
7775
7776
7778
7779
7782
7783
7784
7789
7865
7869
7876
7879
7982
8065
8076
8083
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Oriya
Punjabi
Polish
Pashto, Pushto
8375
8376
8377
8378
8379
8381
8382
8385
8386
8387
8465
8469
8471
8472
8473
8475
8476
8479
8482
8484
8487
8575
8582
8590
8673
8679
8779
8872
8979
9072
9085
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Tonga
Turkish
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
AS NECESSARY
Language codes
En
47
TROUBLESHOOTING
If something seems to be wrong with your DVD player, first check the items in the table below.
Symptom
Check
See page
The power does not come on.
• Make sure the power cord is plugged firmly into a
live power socket.
10
A disc does not play.
Playback stops almost
immediately.
• Is there condensation inside the DVD player? (Leave
the player idle with the power on for 1 to 2 hours.)
• Are you trying to use a disc that can’t be played,
such as a PHOTO CD?
• Is the disc dirty? Is it loaded properly?
• Does the disc exceed the specified rating level?
3
6, 20
41
No picture
• Is the DVD player connected correctly?
• Are the video connections firmly attached?
• Is the television video mode set correctly?
• Do you select “S-Video” in the TV Output Select menu?
10
10
20
45
The picture is bad.
• Is the player in a place with lots of vibration?
• Are the video connections firmly attached?
• Is the disc dirty?
• Is the DVD player connected directly to the television
set? Or is it connected through a video deck, a
selector switch, or a television with a built-in video
deck?
The picture may be bad when used with some
television sets or projectors, due to the DVD copy
protection scheme.
The picture quality may also suffer if the DVD
player is connected through a selector switch with
other video equipment. Try turning off the power to
the other video equipment.
The picture quality may be somewhat poor when
paused, when doing Frame Advance, or during fast
forward or fast reverse. This is normal.
3
10
6
10
No sound
• Is the DVD player connected correctly?
• Are the audio connections firmly attached?
• Is the connected audio equipment turned on? Is the
volume set correctly? (Note that there will be no
audio playback during slow playback, Frame
Advance, fast forward, or fast reverse.)
10
10
20
The remote control does not
work, or does not work correctly.
• Are the remote control batteries installed correctly?
• Is the remote control too far from the main unit? Is
there something in the way?
• Are the remote control batteries getting weak?
• Is the DVD player in sunlight or strong fluorescent light?
19
19
DVD has many capabilities
Some of these capabilities may differ based on the disc
being played. The following situations may be caused by
information on the disc itself.
• The audio or subtitles are not reproduced in the
specified default language.
• The audio track or subtitles cannot be changed.
• There are no subtitles.
• No DVD menu. The DVD menu does not display
in the language you want.
• The view angle cannot be changed.
• Everything on the disc is played back regardless
of the rating level you have set.
48
5
19
19
Power supply
Power consumption
Weight
External dimensions
Laser
Signal format
Supported discs
S video output
Video output
230 V AC, 50 Hz
16 W
3.2 kg
430 × 88 × 245 mm (w × h × d)
Semiconductor laser,
wave length 650/750 nm
PAL/NTSC
DVD video discs
12 cm (single-sided single-layer,
single-sided double-layer,
double-sided double-layer)
8 cm (single-sided single-layer,
single-sided double-layer,
double-sided double-layer)
Compact discs (CD-DA, video CD)
12 cm and 8 cm discs
Y output: 1 Vp-p (75 ohms, sync
negative)
C output: 0.286 Vp-p
1 Mini DIN 4 pin
Video composite output
1 Vp-p (75 ohms, sync negative)
1 RCA jack
• Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the doubleD symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. ©1992-1997
Dolby Laboratories. All rights reserved.
• Manufactured under license from Digital Theater
Systems, Ino. US Pat. No. 5,451,942 and other
worldwide patents issued and pending. “DTS” and
“DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc. ©1996 Digital Theater
systems, Ino. All rights reserved.
• Spatializer® 3-D Stereo, Spatializer N-2-2 (TM)
and the circle-in-square device are trademarks
owned by Desper Products, Inc,.”
1 Scart connector
Audio output
Digital output
0.5 Vp-p (75 ohms)
1 Fiber optical connector
1 RCA jack
Analogue output
2.0 Vrms (1kHz, 0dB, 330
ohms)
1 RCA jacks (L/R)
Audio output characteristics
Signal to noise ratio
More than 105 dB (EIAJ)
Dynamic range
More than 95 dB (EIAJ)
Harmonic distortion
0.003%
Frequency range:
CD / VCD: 2 Hz to 20 kHz
DVD: 2Hz to 22kHz (48kHz
sampling)
2Hz to 44kHz (96kHz
sampling)
Wow and flutter: unmeasurable
Operating conditions 5˚C to 35˚C
Accessories
Video cable (1)
Audio cable (1)
Remote control (1)
Specifications are subject to change without notice.
49
AS NECESSARY
SPECIFICATIONS
Download PDF

advertising