Akai LCT3226 Flat Panel Television User Manual

1. Safety Guidelines
Caution: Always use a power cable is properly grounded. Please use the AC cords listed
below for each area:
USA ..................... UL
Canada ................ CSA/cUL
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference will not
occur in a particular installation. If this equipment does cause by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
FCC Warning
To assure continued FCC compliance, the user must the provided grounded power
supply cord and the provided shielded video interface cables to connect to this equipment.
Also, any unauthorized changes or modifications to this equipment would void the user’s
authority to operate this device.
1
IMPORTANT SAFEGUARDS
Important Safeguards
Before using your TV, please read these instructions completely, and keep this manual
for future reference.
Carefully observe and comply with all warnings, cautions and instructions placed on the
unit or described in the operating instructions or service manual.
The User Manual uses the following symbols to ensure a safe operation and prevent
any damage to operators or properties:
WARNING----- Ignorance or inappropriate use may cause
damage to the product.
ATTENTION---Ignorance or inappropriate use may cause injury
to the user.
Examples:
Prohibition
Warning (Attention) symbol (indicating “Electric Shock”).
WARNING
Never place TV on an unstable cart, stand, or table. The TV may
fall, causing serious personal injury, death, or serious damage to
the TV.
Never overload wall outlets and extension cords.
Never allow anything to rest on or roll over the power cord, and never
place the TV where the power cord is subject to wear or abuse.
Keep the product away from moisture:
- Do not expose this appliance to rain or moisture.
- If water penetrates into the product, stop the operation; unplug
the connector and contact with your dealer. Continuous use in
this case may result in fire or electric shock.
WARNING
Never place item such as vases, aquariums, or candles on top of
the TV.
2
Never use a damaged power cord:
Heavy objects, heat, or tensile force may damage the power cord and
cause fire or electric shock.
Never block or cover the slots or openings in the TV cabinet back,
bottom, and sides. Never place the TV:
- on a bed, sofa, rug, or similar surface;
- too close to drapes, curtains, or walls; or
- in a confined space such as bookcase, built-in cabinet, or any
other place with poor ventilation.
The slots and openings are provided to protect the TV from
overheating and to help maintain reliable operation of the TV.
Do not use the product if any abnormality occurs:
If any smoke or odor becomes apparent, unplug the connector
and contact the manufacturer immediately. Do not try to repair
the product by yourself.
WARNING
Avoid using dropped or damaged appliances:
If the product is dropped and the housing is damaged, the internal
components may function abnormally. Unplug the connector
immediately and contact the manufacturer for repair. Continuous use
of the product may cause fire or electric shock.
WARNING
While it is thundering, do not touch the connecting cables or
apparatus.
ATTENTION
Do not install the product close to smoke or moisture:
Fire or electric shock may be caused when the product is installed
close to smoke or moisture.
To not install the product in an area with heavy dust or high
humidity:
Fire or electric shock may be caused when the product is installed in
a place with heavy dust or high humidity.
Instructions for moving the product:
Ensure that the power connector and any other leads are unplugged
before moving the product.
3
IMPORTANT SAFEGUARDS
The power cable should be kept away from heat sources:
The heat produced by any heat source may melt the covering of the
power cable.
Unplug the connector
Hold the power connector when removing the power cable:
Pulling the power cable itself may damage the wires inside the cable
and cause fire or electric shock.
Do not touch the connector with wet hands:
To avoid risk of electric shock.
ATTENTION
Insert batteries in accordance with instructions:
Insert the batteries with correct polarities (positive  and negative ).
Incorrect polarities may cause breakage and leakage of the
batteries, hurt operators and contaminate the remote controller.
Do not block or cover the vents:
Blocking the vents may cause overheating and fire. Do not install the
product in a place with little or no ventilation. Never cover the vents
with towels, blankets or dusters.
Unplug the connector:
Unplug the power connector when the product will not be used
for a long time.
Unplug the connector
Always make sure the antenna system is properly grounded to provide adequate
protection against voltage surges and built-up static charges.(see Section 810 of the
National Electric Code.)
Antenna lead-in wire
Ground clamp
Electric service equipment
Ground clamp
Antenna discharge unit
(NEC Section 810-20)
Grounding conductors
(NEC Section 810-21)
Power service grounding
electrode system (NEC Art 250 Part H)
Use extreme care to make sure you are never in a position where your body (or any
item you are in contact with, such as a ladder or screwdriver) can accidentally touch
overhead power lines. Never locate the antenna near overhead power lines or other
electrical circuits. Never attempt to install any of the following during lightning activity:
a). an antenna system; or b).cables, wires, or any home theater component connected
to an antenna or phone system.
4
Others:
1). The LCD panel on this TV is manufactured using an extremely high level of
precision technology; however, an occasional pixel (dot of light) may display
constantly on the screen.
This is a structural property of LCD technology and is not a sign of
malfunction.
Such pixels are not visible when the picture is viewed from a normal viewing
distance.
2). LCD (Liquid Crystal Display) may cause interference in image, sound, etc. of
the other electronics that receive electromagnetic waves (i.e. AM radios and
video equipment) under certain installed condition. In particular, it may affect
electronic equipment beyond the residential until where a LCD TV is used.
3). The screen on this TV is manufactured from glass. To prevent damage, never
strike the glass with a sharp or heavy object.
4). Your LCD television contains a small amount of Mercury. When the television
is no longer useful, please follow local electronic waste guidelines for proper
disposal.
5). If you have the LCD screen facing to the sun, the LCD screen will be
damaged. Locate the TV in the place such away from windows side or out side
of the rooms with windows.
6). This product is designed for indoor use only. The operating temperatures are
5°C ~ 30°C.
5
IMPORTANT SAFEGUARDS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
CONTENTS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that product heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. The apparatus shall not be exposed to dripping or splashing and that no objected
filled with liquids, such as vase, shall be placed on the apparatus.
6
Contents
Important Safeguards ......................................................................................2
1. Before use ...................................................................................................8
1.1 Open the Package ...................................................................................... 8
1.2 Installation ................................................................................................... 8
2. Product Features .........................................................................................9
3. Accessories .................................................................................................9
4. Names and Functions of Parts ..................................................................10
4.1 Front View ................................................................................................. 10
4.2 Rear View ................................................................................................. 11
4.3 Remote Control ......................................................................................... 12
5. Connect Accessory Devices ......................................................................15
6. Basic Operation .........................................................................................18
6.1 Power ON/OFF ......................................................................................... 18
6.2 Selection of Input Mode ............................................................................ 18
6.3 Other Function .......................................................................................... 19
6.4 Using the POP double-window feature ..................................................... 20
6.5 OSD Option Adjustment ............................................................................ 21
6.6 OSD Functions.......................................................................................... 22
7. Technical Specification ..............................................................................45
8. Support the Signal Mode ...........................................................................46
9. Cleaning and Simple Troubleshooting .......................................................47
7
BEFORE USE
PRODUCT FEATURES
ACCESSORIES
1. Before use
The product is a 32” XGA (XGA resolution) LCD TV. It has passed the UL and
cUL safety certifications, and is an ideal product for personal and commercial use. The
product is a precise electronic product. Users should read the following instructions
carefully to maximize the performance and life span of the product:
1.1 Open the Package
-
-
The product is packaged in a carton together with other standard accessories. Any
optional accessories shall be packed separately in another carton.
Due to the size & weight of the product, it is recommended that it should be moved
by a minimum of two people.
The protective glass and the glass substrate are installed on the front of the product.
Since both glasses can be broken and scraped easily, move the product gently.
Never place the unit with the glass facing downwards unless it is protected with soft
pads.
When opening the carton, check that the product is in good condition and that all
standard accessories and items are included.
Whenever possible, use the handles on the back of the Display for transport.
1.2 Installation
-
-
8
Please use caution if wall mounting this product. Follow all directions from the
manufacturer of the wall mount and be sure to securely fasten the product to the
mount. While the TV can be wall mounted, improper wall installation may void the
warranty.
Due to the higher power consumption, always use the jack exclusively designed for
this product. If an extended line is required, please consult with your service agent.
The product should be installed on a flat surface to avoid tipping. The distance
between the back of the product and the wall should be maintained for proper
ventilation.
Avoid installing the product in the kitchen, bathroom or any other places with higher
humidity so as not to shorten the service life of the electronic components.
Please ensure the product be installed horizontally, any 90 degree clockwise or
counterclockwise installation may induce poor ventilation and subsequent component
damage.
To protect the screen and avoid screen burn, do not hold on a static picture for a
long time.
2. Product Features
The 32˝ LCD TV provides quality image displays and is suitable for a variety of multi media
applications:
1. Available input signals
- The standard PC module provides VGA (D-SUB 15 PIN), and DVI (with HDCP) input
connectors.
The product supports PC mode image resolutions up to (1280 x 1024@60Hz) with a
vertical frequency of 60 Hz.
- The Video module provides composite video (RCA), S-video (DIN 4 PIN) and
component video (RCA) input connectors. It supports the quality input images of
DVD and HDTV (480P/720P/1080i). The Video module also provides one set of
Stereo Audio output.
- The TUNER Module
The RF input terminal is for ANTENNA and CABLE TV channels.
2. Power Management Function
The machine provides an automatic power control function.
3. XGA LCD TV Panel
The XGA LCD TV panel provides high resolution and high contrast image. The
number of pixels is 1366 (H) x 768 (V). The contrast is 1000:1.
4. Others
- PIP/POP Function: The user may watch image from two source at same time.
- The LCD TV unit provides warm, middle and cool color temperature options. The
user may customize their favorite color temperature.
3. Accessories
1
User Manual x 1
2
Stand x 1
3
AC Cable x 1
4
Remote Control x 1
5
Battery(UM-4/R03/AAA) x 2
6
Warranty Card x 1
7
Insertion Card x 1
9
NAMES AND FUNCTIONS OF PARTS----FRONT VIEW----REAR VIEW
4. Names and Functions of Parts
4.1 Front View
Sketch map
POWER
IR
SOURCE MENU
CH.
VOL.
STANDBY
Push the power switch (O: Off, I: On).
(IR) Infrared Receiver: Receives IR signals from the remote control.
(Power on / Standby) LED: Press (Power) to turn on and off.
Indicator on (Red)
Standby mode
Indicator on (Green)
Power on mode
The functions of the buttons are described as follows:
STANDBY: Press
VOL.
(Standby) to turn on and turn off.
A. They are used as ◄ / ► buttons in the OSD Menu screen.
B. Press to adjust the volume.
CH.
A. They are used as ▲ / ▼ buttons in the OSD Menu screen.
B. Press to scan through channels. To scan quickly through channels, press and hold
down either channels.
MENU: Press to display the menu. Press again to exit the menu.
SOURCE: Press to cycle display TV, AV, S-Video, Component 1, Component 2, DVI and VGA
source menu. When display the OSD-menu, press it to confirm.
10
4.2 Rear View
Sketch map
Use the included power cord and connect to an earthed 100-240V, 50/60Hz AC outlet.
Signal input and other terminals:
. DVI(HDCP) Audio INPUT: Connect to the audio L and R output jacks of a device
with DVI Audio output.
. ANT In: Connect antenna or cable 75 Ohm coaxial Aerial to receive TV/CABLE signal.
. DVI(HDCP) INPUT: Connect to the digital video output jack of a device with DVI output.
. VGA Audio INPUT: Connect the audio terminal to the audio output terminal of the PC.
. AUDIO OUTPUT: Connect audio amplifier or other TV set that with audio input.
. D-SUB(VGA) INPUT: For PC display purpose. Connects to the Mini D-Sub 15 pins
analog output connector of the PC display card.
. COMPONENT1,COMPONENT2 YPbPr/YCbCr INPUT: Connect the separate
component video cables to the device having component video outputs
(YPbPr/YCbCr) to the Y, Pb/Cb, and Pr/Cr jacks of the TV.
COMPONENT1, COMPONENT2 YPbPr/YCbCr AUDIO INPUT: Connect the audio
cable to device’s audio L and R jacks and to the L and R audio jacks of the TV.
. VIDEO INPUT: Video and Audio inputs for external devices, such as a camcorder or
VCR.
. AUDIO INPUT: With AV and S-Video inputs share this terminal.
. S-VIDEO INPUT: Video inputs for external devices with an S-Video output.
11
REMOTE CONTROL
4.3 Remote Control
Power ( ): Press to turn on and off.
Mute (
): Press to mute the sound.
Press again or press VOL+ / VOL- to
restore the sound.
0~9 Number Buttons: Press 0~9 to
select a channel; the channel changes
after 2 seconds.
PIP POS: Press to change the PIP
window position under PIP mode.
SOURCE: Press to select the signal
source, such as TV, AV, S-Video,
Component 1, Component 2, DVI or
VGA.
SLEEP: Press repeatedly until it
displays the time in minutes (5 Min,
10 Min, 15 Min, 30 Min, 60 Min, 90
Min, 120 Min and, OFF) that you
want the TV to remain on before
shutting off. To cancel sleep time,
press SLEEP repeatedly until sleep
OFF appears.
PIP: Press to cycles through the
different POP or PIP modes, such as
Basic PIP, LR POP, and exit.
VOL +/-: Press to adjust the volume.
CH +/- : Press to scan through
channels. To scan quickly through
channels, press and hold down either
channels.
MTS: Press repeatedly to cycle through
the Multi-channel TV sound (MTS)
options: Mono, Stereo and SAP
(Second Audio Program).
◄,▲,▼,►, ENTER: Press ◄, ▲, ▼, ► to move the on-screen cursor. To select an
item, press ENTER to confirm.
SYSTEM: Press repeatedly to cycle through the system options: AUTO and NTSC3.58.
(This button is active for AV, S-Video input source.)
MENU: Press to enter into the on-screen setup menu, press again to exit.
V-CHIP: Press to select the child protect mode.
CCD: Press to select the Closed Caption mode.
FREEZE: Press to freeze the picture, press again to restore the picture.
DISPLAY: Press to display the channel information and it disappear after 3 seconds.
FAVORITE: Press repeatedly to cycle through the favorite channel list.
(Continued on next page)
12
Add/Erase: Press to add or delete
favorite channel.
SOUND: Press repeatedly to cycle
through the sound mode: Normal,
News, Cinema, Flat and User.
PIC SIZE: Press repeatedly to cycle
through the picture size that best
corresponds your viewing
requirements: Normal, Full, Wide1,
Wide2, Wide3, 4:3, No scale, and
Panoramic .
When in POP mode available picture
sizes are: Full, 4:3 and Normal.
P.MODE: Press repeatedly to cycle
through the picture mode: Hi-Bright,
User, Dark, Normal and Vivid.
ZOOM: Press to zoom the image.
RECALL: Press it return to previous
channel.
PIP SIZE: Press to cycle through the
PIP size, such as Large, Medium,
Small.
Insertion of Batteries:
- Turn the remote control upside down, press and slide off the battery cover.
- Insert two 1.5V (AAA) batteries into the compartment, take care to observe the  and 
markings indicated inside.
- Replace the cover and slide in reverse until the lock snaps.
13
REMOTE CONTROL
CONNECT ACCESSORY DEVICES
Range of Remote Control
Sketch map
20°
20°
30°
30°
- Ensure the remote control is pointed towards the remote control window on the display
unit.
- No obstacles should be placed between the remote control and the remote control
window.
- The effective receiving range for the signal is within 5-8 meters from the front of the
remote control window, and 30° to the left or right side and 20° above or below the
control window.
Care For Remote Control
- Avoid spilling liquids on the remote.
- Avoid dropping or otherwise jarring the remote.
- Always store the remote control at dry and normal room temperature place.
- If the remote is nor performing satisfactorily, replace the batteries. The batteries should
be replaced after one year.
- If the remote control will be idled for a long time (above 1 month) take out the batteries
to avoid leakage from the batteries.
- Clean up the entire remote control especially the battery compartment if any leakage
found.
- Do not mix using different kind of new and used batteries together to avoid leakage.
14
5. Connect Accessory Devices
Connecting a DVD player or other
equipment
Switch off TV and external equipment before
connecting cables.
1. Connect a DVD player or other
equipment’s Component Video Out
(Y,Cb,Cr / Y,Pb,Pr) to the TV’s
corresponding Component In (Y,Cb,Cr /
Y,Pb,Pr) jacks on COMP1 or COMP2.
2. Connect a DVD player’s Audio Out to the
TV Component L/R jacks.
3. Press POWER to turn on the TV. Turn
on external equipment also.
4. Press SOURCE to select COMPONENT
1 or COMPONENT 2 signal source.
Green
Red
Blue
White
Red
DVD or Set-top box
Connecting the Computer
Switch off TV and external equipment before
connecting cables.
1. Connect a computer’s VGA Out to the
TV’s D-Sub(VGA) In jacks.
2. Connect a computer’s Audio Out to the
TV’s Audio In jack.
3. Press POWER to turn on the TV. Turn
on external equipment also.
4. Press SOURCE to select VGA signal
source.
15
CONNECT ACCESSORY DEVICES
Connecting the DVD or VCR player
devices
Switch off TV and external equipment before
connecting cables.
1. Connect a DVD or VCR player’s Video
Out to the TV’s Video In jack by a Video
cable.
2. Connect a DVD or VCR player’s S-VIDEO
Out to the TV’s S-VIDEO In jack by a
S-VIDEO cable.
3. Connect a DVD or VCR player’s Audio
Out to the TV’s L/R jacks by a Audio
cable, in this stage, the S-VIDEO and
VIDEO is sharing this L/R Audio in
channels.
4. Press POWER to turn on the TV. Turn on
external equipment also.
5. Press SOURCE to select AV or S-VIDEO
signal source.
Connecting a device to the DVI(HDCP)
Switch off TV and external equipment before
connecting cables.
1. Connect a DVD play or other
equipment’s DVI Out to the TV’s
DVI(HDCP) In jacks.
2. Connect a DVD player’s Audio Out to the
TV Component L/R jacks.
3. Press POWER to turn on the TV. Turn
on external equipment also.
4. Press INPUT to select DVI signal source.
Yellow
Red
White
DVD or VCR player
Red
White
DVD or Set-top box
16
Connecting AUDIO OUTPUT jacks to a
stereo amplifier
Switch off TV and external equipment before
connecting cables.
1. Connect the TV Audio Output (R/L) to the
stereo amplifier In (R/L).
2. Press POWER to turn on the TV. Turn
on external equipment also.
Connecting directly to cable or an
antenna
When using 75Ω coaxial Aerial: Connect
directly to the RF terminal of the tuner.
White
Red
Stereo Amplifier
VHF Antenna
1m above
UHF Antenna
Special Antenna
Mixer
RF(VHF/UHF) terminal
75Ω Coaxial Aerial
17
POWER ON, OFF
SELECTION OF INPUT MODE
OTHER FUNCTION
6. Basic Operation
6.1 Power ON/OFF: The Display is in
Standby mode
POWER
- Press the POWER on the remote control or
Standby on the control panel to turn on the
unit. The power indicator changes from red to
green.
- Press the POWER on the remote control or
Standby on the control panel again to return
the display to standby mode.
SOURCE
The power indicator changes from green to
red.
Note: ⑴ Press CH +/- on the remote control can
CH+/CHturn on TV set from last preview mode.
⑵ For protecting your LCD TV product, the ◄,► ENTER
interval time between turn on the LCD TV
product and shut down it should be kept
at least one minute.
6.2 Selection of Input Mode
- Press SOURCE /
on the remote control or
on the LCD TV control panel to select the
signal source you desired.
ADD/EARSE
FAVORITE
When no input from the selected signal
source, “Main no signal” will appear, press
SOURCE /
on the remote control or on the
control panel again to search the next source.
Note: The LCD-TV will automatically turn itself
off after approximately 15 minutes if no
signal input. When no signal is inputed for
about 14 minutes. A “No signal and going to power down” wording will appear.You
can press “◄” or “►” button to selected, press “ENTER” to confirm. If select “Cancel”
or no operation, the LCD-TV will automatically turn off after 1 minutes, if select “OK”,
it will turn off immediately.
6.3 Other Function
-
18
FAVORITE:
Press FAVORITE button repeatedly, you will cycle through Favorite Channel.
ADD/ERASE:
Press this button to add/erase current channel to/from the list of favorite directly.
Add current channel into the list of favorite if a heart shape mark
displaying on
the left top of screen.
Erase current channel from the list of favorite if a broken heart shape mark
displaying.
(Continued on next page)
Note: - If you don’t want do add/erase this channel to/from the list of favorite, press this
button again.
- For addition, it will be put at last of the favorite list and the first channel in
favorite list will overflow in case of the list is full.
SLEEP:
Press repeadtedly until it displays the time in minutes (5 Min, 10 Min, 15 Min, 30
Min, 60Min, 90 Min, 120 Min and OFF) that you want the TV to remain on before
shutting off.
Note: When in one minute before shutting off. A “Turn off by Timer setting” wording will
appear, you can press ◄ or ► button to selected, press “ENTER” to confirm.
If select “OK” , the LCD-TV will turn off immediately, if select “Cancel”, it will cancel
sleep time.
-
-
RECALL :
Press to switch between present channel
and previous channel.
Note: If the previous channel is a locked channel,
it display blue background and lock
information.
-
FREEZE:
Press it to hold the current video and press
again to cancel and return to normal
viewing.
SLEEP
FREEZE
DISPLAY
-
FREEZE
ZOOM :
Press to zoom the image.
DISPLAY:
Press once to display the information as
following, and disappear after 3 second;
When in TV mode
68
Mono Stereo Sap
RECALL
ZOOM
When in VGA mode
VGA
640 x 480 60Hz
(Continued on next page)
19
USING THE POP DOUBLE-WINDOW FEATURE
OSD OPTION ADJUSTMENT
6.4 Using the POP double-window feature
The POP (picture-out-picture) feature splits the screen into a double window that
allows you to watch two programs at the same time. The POP program can come
from a TV broadcast or an external source, such as a VCR.
To display a TV broadcast in the POP window:
1. Press PIP button to enter the POP window.
Press PIP for selecting the different POP
modes, such as following;
Normal Picture
SOURCE
PIP
Basic PIP Mode
LR POP Mode
Use ◄/► to select the window and active it
with a red-colored frame.
Press SOURCE to select the input source for
the POP window.
2. To change the next programmed
channels, press number buttons (0~9) or CH+/CH-.
Note: a. If the V-CHIP feature is active and you try to watch a TV program that exceeds your
set rating limits, the program will be blocked.
b. For active window, you can change channels, adjust volume, select input source ect..
After power off, the active window will be keep the setting when you power on next
time.
c. It is must to have second video source connected for basic PIP and L/R POP modes.
(Continued on next page)
20
To display a picture from an external source in the POP window:
1.
2.
3.
4.
Connect the external source equipment. (refer to Connect Accessory Devices page).
Select the TV program you want to watch in the main window.
Press PIP to display the POP window.
Repeatedly press SOURCE to select the input source for the POP window.
To change the PIP picture size:
Press PIP SIZE button to select the PIP
picture size, such as: Small, Middle, Large.
To change the PIP position:
Press PIP POS button to change the PIP
window position under PIP mode, it display
as following;
Right Down → Left Down → Left Up →
Right Up → Right Down
PIP SIZE
PIP POS
Left Up
Right Up
ENTER
Left Down
Right Down
Switching the pictures:
When in Basic PIP mode, press “ENTER” to
swap main or sub pictures; When in LR POP
mode, press “ENTER” swap the L/R pictures.
To change Main or Sub sound:
When the red frame is displaying in main
window, the sound goes out of main window
source. If it display in sub window, the sound
goes out of sub window source.
6.5 OSD Option Adjustment
Learning about the menu system
After you have installed the batteries and programmed the remote control, you
will need to set some preferences on the TV using the menu system. You can
access the menu using the buttons on your TV or remote control.
The OSD menu displayed in the following sequence (circular display):
Video
Audio
Misc
TV
Geometric
(Continued on next page)
21
OSD OPTION ADJUSTMENT
OSD FUNCTIONS ---- VIDEO MENU
Press MENU to display the menu system.
Press ◄/► to select a menu.
Press ▲/▼ to select an item.
Press ENTER on the remote control or
SOURCE on the TV control panel to
activate the function settings in the menu.
Press ▲,▼,◄,► to select or adjust a
setting, press ENTER to confirm.
If you do not make a selection within 15
seconds, the main menu closes
automatically; the other menus close
automatically within 6 seconds.
Press ◄ to return OSD-menu.
To close an on-screen menu instantly,
press MENU on the remote control or
MENU on the control panel.
SOURCE
ENTER
MENU
TV control panel
SOURCE MENU
CH.
VOL.
STANDBY
SOURCE MENU
6.6 OSD Functions
1 Using the Video Menu
Option
Contrast
Brightness
Back Light
Saturation
Hue
Sharpness
Phase
Color
Temperature
Advanced
Picture Adjust
Note:
Press ▲/▼
0~100
0~100
Bright, Middle, Dark
0~100
-30~+30
0~7
0~31
Cool, Middle, Warm,
User
Description
Reduce/Enhance
Darken/Brighten
Adjust the balance of back light
Decrease/Increase of color
Decrease/Increase
Soften/Sharpen
Decrease/Increase
Adjust the balance of
whitening
Adjust the picture effect
Video Menu is just for TV, AV, S-Video, Component 1 and Component 2 input source
mode. It is not available in other input source mode.
(Continued on next page)
22
■ Adjustment of “Contrast”
Press MENU on the remote control, and then press ◄ or ► until the “Video” menu
appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to decrease that will soften the color. Press ► to increase that will make
white area more bright.
Press “ENTER” to confirm the adjustment and return.
■ Adjustment of “Brightness”
Press MENU, and then press ◄ or ►until the “Video” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to decrease. Press ► to increase that will brighten the dark area for seeing
the objects in shadowness more clear.
Press “Enter” to confirm the adjustment and return.
(Continued on next page)
23
OSD FUNCTIONS----VIDEO MENU
■ Adjustment of “Back Light”
Press MENU, and then press ◄ or ► until the “Video” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” and then press ▲ or ▼ to select one of “Bright”, “Middle” or “Dark”
for the balance of back light.
Press “ENTER” to confirm the adjustment. Press ◄ to return.
■ Adjustment of “Saturation”
Press MENU, and then press ◄ or ► until the “Video” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to decrease. Press ► to increase that will make color more intensive.
Press “ENTER” to confirm the adjustment and return.
(Continued on next page)
24
■ Adjustment of “Hue”
Press MENU, and then press ◄ or ► until the “Video” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to decrease that will make image more green. Press ► to increase that will
make image more red.
Press “ENTER” to confirm the adjustment and return.
■ Adjustment of “Sharpness”
Press MENU, and then press ◄ or ► until the “Video” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ or ► to increase or decrease that will make image with more sharp edge.
Press “ENTER” to confirm the adjustment and return.
(Continued on next page)
25
OSD FUNCTIONS----VIDEO MENU
■ Selection of “Phase” setting
Press MENU, and then press or until the “Video” menu appears.
Press or to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press to decrease. Press to increase.
Press “ENTER” to confirm the adjustment and return.
Note: This is a feature just used for COMPONENT input source.
■ Selection of “Color Temperature”
Press MENU, and then press or until the “Video” menu appears.
Press or to highlight the item.
Press “ENTER” to confirm.
Press or to select one of “Cool”, “Middle”, “Warm” or “User” for balance of
whitening.
Press “ENTER” to confirm the selection.
Press
to return.
(Continued on next page)
26
If you select the item of “User”, a status bar below comes up for you to adjust the color
temperature to you desirable value.
■ Selection of “Advance Picture Adjust”
Press MENU, and then press ◄ or ► until the “Video” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm for sub-selection as shown in the table below.
Table of Auto Adjustment Setting
Item
DNR
White Peak Limitator
CTI
Flesh Tone
Adaptive Luma
Control
Status
Description
Selecting to control the
Off, Low, Middle,Strong sharpness and noise
reduction.
Select “On” to limit the
On, Off
white peak.
Low, Middle, Strong,
Select dynamic color
Off
improve level.
Select “On” to correct
On, Off
the flash tone
automatically.
Selecting to control the
On, Off
lum.
Press “ENTER” to confirm the selection.
Press◄ to return.
(Continued on next page)
27
OSD FUNCTIONS----AUDIO MENU
2 Using the Audio Menu
Option
Bass
Treble
Balance
Surround
Press ▲/▼
0~100
0~100
-20~+20
On, Off
Description
Decrease/Increase
Decrease/Increase
Emphasize left/right speaker
■ Adjustment of “Bass”
Press MENU, and then press ◄ or ► until the “Audio” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to decrease the Bass sound. Press ► to increase it.
Press “ENTER” to confirm and return.
■ Adjustment of “Treble”
(Continued on next page)
28
Press MENU, and then press ◄ or ► until the “Audio” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to decrease the treble sound, press ► to increase it.
Press “ENTER” to confirm and return.
■ Adjustment of “Balance”
Press MENU, and then press ◄ or ► until the “Audio” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press ◄ to emphasize the left speaker. Press ► to emphasize the right speaker.
Press “ENTER” to confirm and return.
■ Selection of “Surround”
Press MENU, and then press ◄ or ► until the “Audio” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ▲ or ▼ to select “On” or “Off”.
Press “ENTER” to confirm your selection.
Press ◄ to return.
(Continued on next page)
29
OSD FUNCTIONS----MISCELLANEOUS MENU
3 Using the Miscellaneous Menu
Option
Language
Closed Caption
V-Chip
Parental
Blue Mute
Default
Press ▲/▼
Description
English, Français,
Select the OSD language
Español
C1, C2, C3, C4, T1, To select Captions or Text
T2, T3, T4, Off
Enter to V-Chip function
Enter to Parental function
Select it to set screen to
On, Off
pleasant blue background
Select to restore factory default
settings.
■ Selection of “Language”
Press MENU, and then press ◄ or ► until the “Misc” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ▲ or ▼ to choose the OSD language.
Press “ENTER” to confirm your selection.
Press ◄ to return.
■ Selection of “Closed Caption”
(Continued on next page)
30
The closed caption features has two options:
Adjustment only for TV, AV, S-VIDEO input signal.
• Captions: An on-screen display of the dialogue, narration, and sound effects of the
TV programs and videos that are closed captioned (usually marked as
“C/C” in TV listings.
• Text
: An on-screen display of information not related to the current program,
such as weather or stock data (when provided by individual stations).
To view captions or text:
Press MENU, and then press ◄ or ► until the “Misc” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ▲ or ▼ to choose one of “C1”, “C2”, “C3”, “C4”, “T1”, “T2”, “T3”, “T4”, as
follows:
• To view captions, highlight C1, C2, C3, or C4 (C1 displays translation of the primary
language in your area).
Trees near the church.
•
To view text, highlight T1, T2, T3, or T4.
World Weather
New York
London
HongKong
Note:
Note: If the program or video you selected is not
closed captioned, no captions will display
on-screen.
Temp
F
53
51
80
C
12
11
25
Current
Weather
Sunny
Cloudy
Clear
Note: If text is not available in your area, a black
rectangle may appear on-screen. If this
happens, turn off the Closed Caption
feature.
A closed caption signal may not display in the following situations:
▪ when a videotape has been dubbed
▪ when the signal reception is weak
▪ when the signal reception is nonstandard
Select “Off” to close this function.
Press “ENTER” to confirm your selection.
Press ◄ to return.
Hot keys:
- You can also press CCD on the remote control to select you desired item.
31
OSD FUNCTIONS----MISCELLANEOUS MENU
■ Setting of “V-Chip”
Some programs and movies include signals that classify the content of the program
(dialog, language, sex, violence). The “V-Chip” control feature in this detects the
signals and blocks the programs according to your selections. To use this feature,
perform the following setup.
Adjustment only for TV, AV, S-VIDEO input signal.
Press MENU, and then press ◄ or ► until the “Misc” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
The “V-Chip” menu includes the “V-Chip Control”, “Block MPAA Rating”, and “Block TV
Rating” functions. You can use these functions after entering the correct PIN code.
▪
▪
Entering the PIN code
Blocking Reset status:
Set your 4-digit code by pressing the Number buttons (0~9), and then press ENTER.
When the PIN code is already stored:
Press the Number buttons (0~9) to enter the 4-digit PIN code used for blocking
channels, and then press ENTER.
Note: The initial password for the system is “0000”.
If you had forgotten the password, please contact with service centre.
If the input is invalid, a message will pop up as below;
(Continued on next page)
32
You can press “ENTER” to display “Input Your Password Please” menu again, then
entering the PIN code, or press “ ▼ , ▲ , ◄ or ►” move cursor to “Cancel” and press
“ENTER” button to close up this menu.
Using the “V-Chip Control” item
When enter the “V-CHIP” menu, select “V-Chip Control”.
Press ▲ or ▼ to highlight the “V-Chip Control” item.
Press “ENTER” to confirm and then press ▲ or ▼ to select “ON” or “OFF”.
ON : TV Blocking and MPAA Blocking are activate.
OFF : TV Blocking and MPAA Blocking are not activate.
Press ◄ to return or press MENU to exit.
Using the “Block MPAA Rating” item
When enter the “V-CHIP” menu, select “Block MPAA Rating”.
Press ▲ or ▼ to highlight the “Block MPAA Rating” item.
Press “ENTER” to confirm.
Press ▲ or ▼ to select an item, then press “ENTER” to lock (display “
(display “
”).
”) or unlock
(Continued on next page)
33
OSD FUNCTIONS----MISCELLANEOUS MENU
The movie block you can lock are described as follows:
Item
G
PG
Description and Content themes
General Audience (Appropriate for all ages)
Parental Guidance Suggested (Some material may not be suitable for
children)
PG-13
Parents Strongly Cautioned (Some material may be inappropriate for
children under 13)
R
NC-17
X
Restricted (Under 17 requires accompanying parent or adult guardian)
Not intended for anyone 17 and under
X-rated (For adults only)
Press MENU button to exit the sub-menu.
Using the “Block TV Rating” item
From the “V-CHIP” menu, select “Block TV Rating”.
Press ▲ or ▼ to highlight the “Block TV Rating” item.
Press “ENTER” to confirm.
Press ▲ , ▼ , ◄ , ► to select an item, then press “ENTER” to lock (display “
or unlock (display “
”).
”)
(Continued on next page)
34
The aged-based TV Guideline and content themes you can lock are listed as
follows:
Item
TV-Y
Description and Content themes
All Children (This program is designed to be appropriate for all
children.)
TV-Y7
Directed to Older Children (This program is designed for children age 7
and above.
Note: Programs in which fantasy violence may be more intense or more
combative than other programs in this category are designed TV-Y7.)
TV-G
General Audience (Most parents would find this program suitable for all
ages.)
TV-PG
Parental Guidance Suggested (This program contains material that parents
may find unsuitable for younger children.)
D) Some suggestive dialog
L) Infrequent coarse language
S) Some sexual situations
V) Moderate violence
TV-14
Parents Strongly Cautioned (This program contains some material that
many parents would find unsuitable for children under 14 years of age.)
D) Intensely suggestive dialog L) Strong, coarse language
S) Intense sexual situations
V) Intense violence
TV-MA
Mature Audience Only (This program is specifically designed to be viewed
by adults and therefore may be unsuitable for children under 17.)
L) Crude or indecent language S) Explicit sexual activity
V) Graphic violence
Press MENU button to exit the sub-menu.
Unlocking programs temporarily
If you try to watch a TV program that exceeds the TV Guideline you set, the TV
enters program lock mode. You can either unlock the program temporarily or select
a non-locked program to watch, press ▲ or ▼ to select the program.
To temporarily unlock the program, press the Number buttons (0~9) to enter your 4digit PIN code.
V-CHIP BLOCK
TV-PG
LV
Enter Password
If the correct code is entered, the program lock mode is released and the normal picture
appears.
Hot keys:
- You can also press V-CHIP on the remote control to enter V-Chip menu.
35
OSD FUNCTIONS----MISCELLANEOUS MENU
■ Setting of “Parental”
The TV programs and movies shown on TV are given a rating signal based on the
following rating systems.
To block programs you feel unsuitable for your children, you need to set the TV for
the desired rating systems. The TV’s “Parental” control feature functions by receiving
the rating signal from your local broadcasting station or cable service provider.
Press MENU, and then press ◄ or ► until the “Misc” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
The “Parental” menu includes the “Channel Lock”, “Video Lock”, “Change Password”
and “Clear All” functions.
You can use these functions after entering the correct PIN code.
▪
Entering the PIN code
Blocking Reset status:
Set your 4-digit code by pressing the Number buttons (0~9), and then press ENTER.
▪
When the PIN code is already stored:
Press the Number buttons (0~9) to enter the 4-digit PIN code used for blocking
channels, and then press ENTER.
Note: The initial password for the system is “0000”.
If you had forgotten the password, please contact with service centre.
If the input is invalid, a message will pop up as below;
(Continued on next page)
36
You can press “ENTER” to display “Input Your Password Please” menu again, then
entering the PIN code, or press “▼, ▲, ◄ or ►” move cursor to “Cancel” and press
“ENTER” button to close up this menu.
Press ▲ or ▼ to choose an item as below table showing.
Press “ENTER” to confirm.
Press ◄ to return.
Items
Channel
Lock
Video Lock
Change
Password
Clear All
Table of Parental Setting
Status
Description
Use the CH+/CH- or ▲/▼ and
All channels
ENTER buttons to select the
channel you desired to lock.
TV1, AV, S-Video,
Use ▲/▼and ENTER buttons to
Component 1,
select the Video you desired to
Component 2, DVI,
lock.
VGA
Enter a new 4-digit code by using
the number keys on the remote,
and then confirm the new code by
entering it a second time, press
“ENTER” to confirm. It will exit this
menu when your code has been
successfully changed.
Press “ENTER” to clear all present
Parental setting.
37
OSD FUNCTIONS----MISCELLANEOUS MENU ---- TV MENU
■ Selection of “Blue Mute”
Press MENU, and then press ◄ or ► until the “Misc” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ▲ or ▼ to choose “On” or “Off”, when select “On” to set screen to a pleasant
blue background when it detects no signal available if turn on.
Press “ENTER” to confirm your selection.
Press ◄ to return.
■ Using “Default”
Press MENU, and then press ◄ or ► until the “Misc” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm, it will reset to restore factory default settings. After that, a
confirmation message will pop up.
Note: Just reset the items in the setup menu don’t include the protected-items(Needs pin
code enter, such as password, video lock, and channel lock) and properties such as
skipped channel, channel name.
38
4 Using the TV Menu
Option
Auto Search
Tuner Mode
Channel Skip
Channel
Name
Note:
Press ▲/▼
Cable, Air
Description
To searching the channel
To select the tuner mode
To skip the channel
Add the channel name
TV menu is only for TV input source mode, thus it is not available in other input
source mode.
The locked channel will be skipped during the searching.
■ Using the “Auto Search”
Press MENU, and then press ◄ or ► until the “TV” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ◄ to return.
■ Using the “Tuner Mode”
(Continued on next page)
39
OSD FUNCTIONS----TV MENU----GEOMETRIC MENU
Press MENU, and then press ◄ or ► until the “TV” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ▲ or ▼ to choose “Air” or “Cable”.
Press “ENTER” to confirm.
Press ◄ to return.
■ Using the “Channel Skip”
Press MENU, and then press ◄ or ► until the “TV” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm.
Press ▲ or ▼ to scan which channel is skipped, there is a the channel.
Press “ENTER” to toggle the channel will be skipped or not.
Press ◄ to return.
■ Using the “Channel Name”
Press MENU, and then press ◄ or ► until the “TV” menu appears.
Press ▲ or ▼ to highlight the item.
Press “ENTER” to confirm, it will display “Channel Name” list.
Use “ ◄ , ► , ▲ , ▼ ” for select, and move cursor to “OK”, then press “ENTER” for
confirm you selection. If you want to cancel this operation, move cursor to “Cancel”
and press “ENTER” for close this setting.
Press ◄ to return.
Note: It will be invalid if the current source is not TV.
40
■ Selecting Channel
Press CH+/- on the remote control to search the channels, the channel number will
increase or decrease by 1 for each pressing excluding the skipped channels.
Press number buttons 0~9 to select the corresponding channel content. If the
channel number is bigger than 9, just press the two number buttons successively. If
the channel number is bigger than 100, just press the three number buttons
successively. The time interval should not exceed 2 seconds.
If the channel number you pressed is bigger than the maximum channel number that
the setting is permitted, the maximum numbered channel content will be remained.
■ Channel Preview
Press RECALL button to switch between present channel and previous channel.
(Only for TV)
5 Using the Geometric Menu
Option
Contrast
Brightness
Back Light
Press /
0~100
0~100
Middle, Bright, Dark
Auto Setting
Phase
Manual Clock
Display
Adjustment
Note:
0~31
0~255
Vertical position,
Horizontal position
Description
Reduce/Enhance
Darken/Brighten
Adjust the balance of back light
To adjust the position of
display automatically
Soften/Sharpen
Decrease/Increase
To adjust the position of
display
If your current input source is “VGA” or “DVI”, push “MENU” enter into this menu. It
is not available in other input source mode.
“Auto Setting”, “Phase”, “Manual Clock” and “Display Adjustment” item can be adjust
when input source is “VGA”.
■ Using Contrast
(Continued on next page)
41
OSD FUNCTIONS ---- GEOMETRIC MENU
Press MENU on the remote control, and then press or until the “Geometric”
menu appears.
Press or to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press
to decrease that will soften the color. Press
white area more bright.
Press “ENTER” to confirm the adjustment and return.
to increase that will make
■ Using “Brightness”
Press MENU, and then press or until the “Geometric” menu appears.
Press or to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press
to decrease. Press to increase that will brighten the dark area for seeing
the objects in shadowness more clear.
Press “ENTER” to confirm the adjustment and return.
■ Using “Back Light”
(Continued on next page)
42
Press MENU, and then press or until the “Geometric” menu appears.
Press or to highlight the item.
Press or to select one of “Bright”, “Middle” or “Dark” for the balance of back
light.
Press “ENTER” to confirm the adjustment. Press
to return.
■ Using “Auto Setting”
Press MENU, and then press or
Press or to highlight the item.
Press “ENTER” to confirm.
Press
to return.
Note:
until the “Geometric” menu appears.
This item will auto-adjust the picture display.
■ Using “Phase”
Press MENU, and then press or until the “Geometric” menu appears.
Press or to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press
to decrease and press to increase it.
Press “ENTER” to confirm and return.
Note: This is a feature used for VGA input source.
43
OSD FUNCTIONS ---- GEOMETRIC MENU
TECHNICAL SPECIFICATION
■ Using “Manual Clock”
Press MENU, and then press or until the “Geometric” menu appears.
Press or to highlight the item.
Press “ENTER” to confirm and display a status bar as below.
Press
to decrease the menu clock. Press
Press “ENTER” to confirm and return.
to increase it.
■ Using “Display Adjustment”
Press MENU, and then press or until the “Geometric” menu appears.
Press or to highlight the item.
Press “ENTER” to confirm for sub-selection as shown in the table below.
Press “ENTER” to confirm your selection.
Press
to return.
Table of Display Adjustment
Items
Vertical
Position
Horizontal
Position
44
Use “
Use “
Use “
Use “
” or “
” or “
” or “
” or “
Description
” to select it and press “ENTER” to confirm.
” to move the image up or down.
” to select it and press “ENTER” to confirm.
” to move the image left or right.
7. Technical Specification
Product Model:
Screen Size:
Screen Area:
Aspect Ratio:
External Size:
Net Weight:
Resolution:
Pixel Dot Pitch:
Color:
Gray Scale:
Brightness(Peak Value):
Contrast(Dark Room):
TV System:
Sound:
Sound Effect:
Power Supply:
Power Consumption:
Input/Output Terminal:
Agent System:
LCT3226
32” diagonal
714.96mm(H) x 404.60mm(V)
16:9
988mm(W) x 514mm(H) x 94mm(D) (w/o Stand)
988mm(W) x 562mm(H) x 235mm(D) (with Stand)
18kg (with Stand)
1366 (H) x 768 (V) pixels (Each pixel has R/G/B 3 color
cells)
173µm(H) x 519µm(V)
16.7 millions of colors (R/G/B each 256 scales)
256 (R/G/B each 8-bit)
550cd/m2 (Typical)
1000:1 (Typical)
NTSC M
Mono, Stereo, SAP (BTSC)
Spatial Effect and Surround
AC 100-240V, 50/60 Hz
≤ 200W
D-Sub 15 Pin (Analog RGB Input)
DVI with HDCP (29 Pin) x 1
Component Video - YPbPr/YCbCr x 2 RCA Terminals
Video Input RCA Terminals
S-Video Input Mini Din 4 Pin Terminal
1 set of Stereo Audio Output Terminals (RCA, L&R)
Audio Input for DVI(HDCP)
Audio Input for Video/S-Video
Audio Input for YPbPr/YCbCr x 2
Audio Input for PC (3.5mm)
UL, cUL, FCC
NOTE:
The specifications shown above may be changed without notice for quality improvement.
45
SUPPORT THE SIGNAL MODE
CLEANING AND SIMPLE TROUBLESHOOTING
8. Support the Signal Mode
A. D-Sub Mode (VGA and DVI)
NO.
Resolution
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1280 x 960
1280 x 1024
Horizontal
Frequency
(KHz)
31.50
35.00
37.50
37.86
31.47
35.16
37.90
46.90
48.08
49.00
48.40
56.50
60.00
63.86
67.52
60.02
64.00
Vertical
Frequency
(Hz)
60.00
67.00
75.00
72.81
70.08
56.25
60.32
75.00
72.19
75.00
60.00
70.00
75.00
70.02
75.02
60.02
60.01
Dot Clock
Frequency
(MHz)
25.18
30.24
31.50
31.50
28.32
36.00
40.00
49.50
50.00
57.27
65.00
75.00
78.75
94.51
108.03
108.04
108.00
Horizontal
Frequency
(KHz)
15.734
31.468
31.25
37.50
45.00
33.75
Vertical
Frequency
(Hz)
59.94
59.94
50.00
50.00
60.00
60.00
Dot Clock
Frequency
(MHz)
13.50
27.00
27.00
74.25
74.25
74.25
B. HDTV Mode (YPbPr)
NO.
Resolution
1
2
3
4
5
6
480i
480p(720x480)
576p(720x576)
720p(1280x720)
720p(1280x720)
1080i(1920x1080)
- When the signal received by the Display exceeds the allowed range, a warning message
“Main no support” shall appear on the screen.
- You can confirm the input signal format from the on-screen.
46
9. Cleaning and Simple Troubleshooting
1 Important:
- Make sure that the power cable is removed from the AC outlet before cleaning the
product.
- Do not use volatile solvent (such as toluene, rosin and alcohol) to clean the Display.
Such chemicals may damage the housing, screen glass and remote control, and cause
the paint to peel.
2 Cleaning of Housing and Remote Control:
- Use a soft cotton cloth for cleaning.
- If the housing or remote control are seriously contaminated, use a soft cloth moistened
with diluted neutral clean the Display. Wring water out of the cloth before cleaning to
prevent water from penetrating into the housing. Wipe the Display with a dry cloth after
cleaning.
3 Cleaning of Screen:
- Use a soft cotton cloth to clean the screen gently.
- The screen glass is very fragile; so do not scrape it with any sharp object. Do not press
or tap the screen to avoid cracking. When the screen is seriously contaminated, use a
soft cloth moistened with diluted neutral cleaner to clean the Display. Wring water out of
the cloth before cleaning to prevent water from penetrating into the housing. Wipe the
display with a dry cloth after cleaning.
4 Simple Troubleshooting:
If the display fails or the performance changes dramatically, check the Display in
accordance with the following instructions. Remember to check the peripherals to
pinpoint the source of the failure. If the Display still fails to perform as expected, contact
the dealer for assistance.
(Continued on next page)
47
CLEANING AND SIMPLE TROUBLESHOOTING
Symptom
Power cannot be turned on.
(Power indicator does not
light)
No Input Signal message
appears.
The remote control does not
function properly.
Flashing spots or stripes
appear on the screen.
Image color or quality
deteriorates.
Screen position and size
are incorrect.
Image or color is incorrect.
The external speaker has
no sound.
Check that the input signal
line is properly fixed, or
display “Main no support”
48
Solution
- Check that both ends of the power cable are plugged into
the socket appropriately.
- Check that the signal line is connected properly.
- Check that the power of the relevant peripherals is turned
on.
- Check that the Input option that has been selected
matches with the input signal.
- Check that the polarity of the batteries are correct.
- Check that the batteries are not drained. (Use new
batteries.)
- Check that the Remote Control is within the operating
range.
- Check that the Remote Control is pointed to the Remote
Control Window on the Display.
- Check that there are no obstacles between the Remote
Control and the Remote Control Window.
- For more information about the Remote Control, refer to
Chapter 6.
- Check that there is no emitter sources (Car, HV cable or
Neon lamp) or other possible interference sources.
- Check that all the video settings are adjusted
appropriately, such as brightness, contrast, color etc.
- For more information about video settings, refer to OSD
Functions in Chapter 6.
- Check that the screen position and size is adjusted
appropriately.
- Check that the signal line is connected properly.
- When connecting to PC, you can change the resolution
of PC to acquire correct image. The discrepancy of the
PC output signal may affect the display of the image.
- Check that the speaker cables are connected
appropriately.
- Check that the Display is not in the Mute mode.
- Check that the audio signal lines from the peripherals are
connected properly.
- Select the correct input signal.
- For more information, refer to Support the Signal Mode
in Chapter 8.