Alcatel Carrier Internetworking Solutions 046

Operating Instructions
SM3-640
Two component proportioning valve
SKW
Sterling Material Processing
SKW
Sterling Material Processing
5200 West Clinton Ave.
Milwaukee, WI 53223
Telephone (414) 354-0970
Fax: (414-354-6421
www.sterlco.com
Parts & Service:
Telephone (800) 423-3183
Edition: 04/97
These operating instructions are for:
*
Serial number:
Built in:
Date of delivery:
Number of delivery:
Date of commissioning:
SM3-640
Location:
Group of machines:
2
SKW
Sterling Material Processing retains all rights to change the information in these
operating instructions at any time without notice.
SM3-640
We assume no liability for any errors or direct or indirect damage resulting in
context with these operating instructions.
Copying, translation or publication in any form except for personal use of
purchaser requires approval from Sterling Material Processing.
All rights reserved.
3
SKW
Table of contents
1. Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.
1.2.
1.3.
1.4.
Warnings and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Explanations and information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
For the operating safety of the equipment . . . . . . . . . . . . . . . . . . 13
2. Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2. Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2.1. Connection to a single conveyor unit
SSE 2&5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2.2. Connection to a vacuum receiver unit
SSK 05, 1, 3, 5 & 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.2.3. Connection to a conveying system control . . . . . . . . . 19
2.3. Compressed air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3. Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1. General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2. Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.1. SKW Version 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.1.1. Conveying ratio . . . . . . . . . . . . . . . . . . . . . . . 24
3.2.1.2. Switching cycles . . . . . . . . . . . . . . . . . . . . . . 25
3.2.2. SKW Version 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4. Start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SM3-640
4.1. Adjusting the conveying ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.2. Determining the switching cycle duration . . . . . . . . . . . . . . . . . . 29
4.3. Setting the switching cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table of contents 4
SKW
5. Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.1. Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.2. Checking for smooth operation . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.1. Dimension sheet SKW 40/50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.2. Dimension sheet SKW 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
SM3-640
7.1. Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table of contents 5
SKW
1. Safety instructions
»
These safety instructions apply to all persons within the
range of action of the equipment.
Please inform all persons within the range of action of the
equipment of the direct and indirect hazards connected
with the equipment.
These operating instructions are to be used by all persons
assigned activities connected with the equipment.
Knowledge of the English language is prerequisite.
SM3-640
Ensure in each case that the operating personnel are
familiar with the operating instructions and the function of
the equipment.
Safety instructions 6
SKW
1.1. Warnings and symbols
The following warnings and symbols are used in these operating instructions:
»
This symbol indicates danger to life! Fatal or serious injury
is possible if the corresponding instructions, regulations or
warnings are not observed.
This symbol indicates that serious injury is possible if the
corresponding instructions, regulations or warnings are not
observed.
F
This symbol indicates that extensive damage to equipment
is possible if the corresponding instructions, regulations or
warnings are not observed.
&
This symbol indicates information important for becoming
familiar with the equipment, i.e. technical correlations.
$
This symbol indicates that a technical term is explained at
this point.
SM3-640
L
Safety instructions 7
SKW
1.2. Explanations and information
Various terms and designations are used frequently in these operating
instructions to ensure clarity. Therefore please note that the terms used in the
text stand for the corresponding explanations listed below.
· Equipment
“Equipment” can mean an individual unit, a machine or an installation.
personnel
· Operating
The “operating personnel” are persons operating the equipment on their own
responsibility or according to instructions (minimum age: 16).
· Operator
The “operator” of the equipment (production manager, foreman, etc.) is the
person responsible for all production sequences. The operator instructs the
operating personnel of what is to be done.
instructions
· Operating
The “plant operating instructions” describe the interaction of the equipment,
production sequences or methods. The plant operating instructions must be
compiled by the operator of the equipment.
foreman
· Equipment
When several operating personnel work on one machine, the “equipment
foreman” coordinates the sequences. The equipment foreman must be
appointed by the operator.
personnel
· Trained
“Trained personnel” are persons who, due to their training, are authorized to carry
SM3-640
out the required work in good practice.
Safety instructions 8
SKW
1.3. For your safety
· The operating personnel of this equipment must be at least 16 years old.
read these operating instructions carefully before taking into operation for
· Please
the first time. All points are to be observed. Contact us should questions arise.
This avoids injury and damage to equipment!
operating instructions must be kept available at all times at the place of
· These
operation of the equipment.
Improper operation results in danger of accidents!
note that, for reasons of clarity, not all conceivable cases regarding
· Please
operation or maintenance of the equipment can be covered in these operating
instructions.
observe all safety instructions and warnings on the equipment.
· Please
This avoids injury and damage to equipment!
work on the equipment is to be carried out by persons whose qualifications are
· All
specified in the pertaining chapters of the operating instructions.
Improper operation results in danger of accidents!
proper working clothes are to be worn during any work on the equipment.
· The
This avoids injury!
the connected loads with those of the mains supply.
· Compare
Danger of injury through electrical shock!
using lifting gear, please observe the pertaining regulations.
· When
Caution: Danger of accidents!
SM3-640
note that all installation, start-up and maintenance procedures are to be
· Please
carried out by qualified, trained personnel only.
Improper operation results in danger of accidents!
Safety instructions 9
SKW
local regulations and requirements pertaining to the equipment must be
· The
observed.
“5 safety rules” as provided in DIN VDE 0105, Section 1, must be observed
· The
for all work carried out on the equipment.
electrical components from the mains supply before work is carried
· Disconnect
out on these components.
Caution: Danger to life through electrical shock!
not modify, add other equipment or change the design of the equipment
· Do
without the approval of the manufacturer.
Caution: Danger of accidents!
detailed plant operating instructions based on the supplied operating
· Compile
instructions for the sequence of procedures to be carried out on this equipment.
Improper operation results in danger of accidents!
· Appoint an equipment foreman to be responsible for the equipment.
that the operating personnel are thorough training in the operation of the
· Ensure
equipment.
Improper operation results in danger of accidents!
the main switch is switched off for reasons pertaining to safety, it must be
· When
secured against unauthorized activation.
Caution: Danger of accidents!
· Before starting maintenance work, appoint a supervisor.
the responsible personnel before maintenance work on the system is
· Inform
started.
SM3-640
Caution: Danger of accidents!
Safety instructions 10
SKW
the equipment from mains supply before starting maintenance
· Disconnect
procedures to ensure that it cannot be switched on unintentionally.
Caution: Danger of accidents!
work may be carried out by trained personnel only.
· Repair
Caution: Danger of accidents!
operate the equipment when partially dismantled.
· Never
Caution! Limbs may be caught in machinery; danger of electrical shock!
case of malfunction, shut down the equipment immediately. Have malfunctions
· Incorrected
immediately.
Caution: Danger of accidents!
equipment is intended only for conveying granulated plastics and regrinds.
· The
Other use of the equipment is contrary to its specifications.
· This equipment is not suitable for food processing.
observe that sound levels exceeding 85 dB(A) may lead to health
· Please
problems after prolonged exposure. Use suitable ear protection.
This prevents ear damage!
not supplied by Sterling must be manufactured in accordance with
· Attachments
safety instruction EN 294.
Caution: Danger of accidents!
all pipes, hoses and screwed connections for leaks and damage on a
· Check
regular basis. Correct such damages immediately.
Caution: Danger of accidents!
SM3-640
all compressed air piping before maintenance work.
· Depressurize
Danger! Limbs may be caught in machinery!
operate the equipment without elbows.
· Never
Danger! Limbs may be caught in machinery!
Safety instructions 11
SKW
equipment may only be operated when all appertaining components are
· The
connected properly and comply with applicable regulations.
· The equipment may only be operated in conjunction with a conveyor unit.
SM3-640
· Observe the safety instructions for connected equipment.
Safety instructions 12
SKW
1.4. For the operating safety of the equipment
· Never change settings if the consequences are not precisely known.
· Use only original Sterlingspare parts.
· Observe the maintenance instructions.
· Keep record of all maintenance and repair procedures.
· Please note that electronic components may be damaged by static discharge.
all electrical connections for secure fit before the equipment is taken into
· Check
operation and at regular intervals.
· Never adjust sensors without exact knowledge of their function.
note that the maximum ambient temperature must not exceed 45 °C
· Please
(113°F).
· Align the suction tubes of the individual components equally.
· Please note that the set conveying ratio determines the conveying time.
· Please note that compressed air supply is required for the operation of the SKW.
set a higher operating pressure than 6 bar (87.02 PSI) for the SKW (system
· Never
overpressure).
SM3-640
whether the regrind is connected to the left-hand intake port (1) of the
· Check
SKW.
VA-steel pipe bends when conveying abrasive material (SKW 40,
· Install
SKW 50).
Safety instructions 13
SKW
· Please note that SKW 65 may not be used for conveying abrasive materials.
· Please note that the SKW can only be used in conjunction with a conveyor unit.
SM3-640
observe the operating instructions of the connected conveyance control
· Please
system.
Safety instructions 14
SKW
2. Installation instructions
»
These installation instructions are intended for persons
with skills in electrical and mechanical areas due to their
training, experience and received instructions.
Personnel using these installation instructions must be
instructed in the regulations for the prevention of
accidents, the operating conditions and safety regulations
and their implementation.
Ensure in each case that the personnel are informed.
The installation instructions provided in the corresponding
operating instructions apply for all connected equipment.
Observe safety regulations with regard to lifting gear
handling
All installation work must be carried out with the equipment
disconnected from electrical power and compressed air
supply.
L
For installation work taking place at heights of over
approx.1829mm (6 ft), use only ladders or similar
equipment and working platforms intended for this
purpose. At greater heights, the proper equipment for
protection against falling must be worn.
Use only suitable lifting gear which is in proper working
order and load suspension devices with sufficient carrying
capacity. Do not stand or work under suspended loads!
SM3-640
Use suitable workshop equipment.
Installation instructions 15
SKW
SM3-640
F
Install the equipment such that all parts are easily
accessible; this facilitates maintenance and repair work.
Installation instructions 16
SKW
2.1. Installation
Installation is possible in any position. A mounting bracket is already attached.
»
The control unit must be accessible at any time
Install VA-steel pipe bends (SKW 40, SKW 50) when
conveying abrasive materials.
SKW 65 may not be used for conveying abrasive
materials.
Install the SKW in such manner that differences in conveying distances for the
two components are avoided.
Please note that the maximum ambient temperature near the SKW must not
exceed 45 °C (113°F).
Remove the plugs from the
pipe bends.
Install the regrind line at intake
port 2 of the SKW.
Install the virgin material line
at intake port 1 of the SKW.
Install the feed line to the
hopper loader at the outlet port
of the SKW.
Align both suction pipes
equally in order to avoid
inaccurate
percentage
preselection results.
SM3-640
Assembly SKW
Installation instructions 17
SKW
2.2. Electrical connection
2.2.1. Connection to a single conveyor unit CSE 2/CSE 5
»
Electrical connections are to be made by trained personnel
only.
Observe the regulations of your local Electricity Board.
All work is to be carried out with the equipment
disconnected from electric power and compressed air
supply.
The power consumption value of the SKW is approx. 15 Watts.
The operating voltage of the SKW is 100 V/60 Hz.
Special voltage on request.
Lay a cable (min. 3 x 1 mm ) from the single conveyor unit to the SKW.
2
Install the supplied plugs.
Install the plug of the SKW at the plug connector of the single conveyor control
unit.
SM3-640
Observe the operating instructions of the single conveyor unit.
Installation instructions 18
SKW
2.2.2. Connection to a vacuum receiver unit SSK-05 1, 3, 5, & 30
»
Electrical connections are to be made by trained personnel
only.
Observe the regulations of your local Electricity Board.
All work is to be carried out with the equipment
disconnected from electric power and compressed air
supply.
The power consumption value of the SKW is approx. 15 Watts.
The operating voltage of the SKW is 24 V.
Lay a cable (min. 3 x 1 mm ) from the single conveyor unit to the SKW.
2
Install the supplied plugs.
Install the plug of the SKW at the plug connector of the single conveyor control
unit.
Observe the operating instructions of the vacuum receiver unit.
2.2.3. Connection to a conveying system controller
»
The electrical connection to a conveying system controller
may only be made by skilled personnel authorized by
Sterling.
SM3-640
Other persons are not permitted to install electrical
connections.
Installation instructions 19
SKW
2.3. Compressed air supply
For actuating the piston in the SKW
a
compressed
air
supply
connection (1/4 inch) is required.
Check compressed air piping for
correct installation and assembly.
Check fittings, length and quality of
the
hose
connections
for
agreement with requirements.
The operating pressure of the SKW
is 5-6 bar (72.52-87.02 PSI)
(system overpressure).
Check the compressed air supplied
by the plant’s supply network.
Maintenance unit
Adjust compressed air pressure to
5-6 bar(72.52-87.02 PSI) (system
overpressure).
Compressed air must be dewatered and oiled.
Install a maintenance unit (pressure reducer with water separator and oiler) if
required.
Connect the SKW to the plant’s supply network by means of a hose.
L
Depressurize compressed air supply lines which must be
opened.
F
Compressed air must be dewatered and oiled.
SM3-640
Adjust pressure to a max. value of 6 bar (87.02 PSI)
(system overpressure).
Installation instructions 20
SKW
3. Functional description
»
This functional description is intended for the operating
personnel of the equipment.
Prerequisite for this functional description is general
knowledge of conveyor systems operation.
Ensure in each case that the operating personnel are
sufficiently informed.
SM3-640
F
The SKW can only be operated in conjunction with a
conveyor unit.
Functional description 21
SKW
3.1. General information
The SKW has 2 elbows (virgin material intake port, regrind intake port) and an
outlet pipe socket leading to the conveyor unit.
With the SKW it is possible to convey two components to a hopper loader.
The SKW works in dependence on the conveying cycles of the conveyor unit. It is
only in operation when material is conveyed.
The SKW is available in 2 versions:
1
· Version
Operation on SKW
SKW for connection to a single conveyor unit CSE 2/5;
2
· Version
Operation on the conveying control
SM3-640
SKW for connection to a conveying control.
Functional description 22
SKW
3.2. Control
3.2.1. SKW Version 1
The control unit is installed at the housing of the SKW.
The conveying ratio as well as the switching cycles are set by means of the keys
on the front side of the control system.
Percentage key
Arrow key
Display
SM3-640
SKW control system
Functional description 23
SKW
3.2.1.1. Conveying ratio
The conveying ratio between component 1 (= regrind) and component 2 (= virgin
material) can be freely selected.
The control setting refers to the conveying time of component 1 (= regrind).
The conveying time of component 1 can be set from 0 to 99 % of total conveying
time.
Example
Proportioning valve setting: 22 %
Conveying ratio: 22 % component 1 and 78 % component 2
Conveying ratio relates to conveying time, not to the
amount of material conveyed.
SM3-640
&
Functional description 24
SKW
3.2.1.2. Switching cycles
During each switching cycle, the SKW switches back and forth one time. The
pre-set conveying ratio is not affected by this. In order to prevent strong formation
of layers in the conveyed material, the number of switching cycles per conveying
procedure can be freely selected. Setting takes place by entry of one cycle
period. The cycle period can be set between 5 and 50 seconds. The setting is
carried out in five seconds.
F
The cycle period may not be longer than the conveying
time.
&
The shorter the cycle period, the higher the number of
switching cycles.
The higher the number of switching cycles, the less
significant is the zoning effect in the hopper loader.
Example
Conveying time: 90 seconds, cycle period = 15 seconds
Calculation of switching cycles:
conveying time
= switching cycles
cycle period
Cycle period must always be high enough that both virgin
material and regrind are conveyed properly.
SM3-640
F
90 s
= 6 switching cycles
15 s
Functional description 25
SKW
3.2.2. SKW Version 2
On the SKW housing, a terminal box is installed (optional: terminal box with 3
light-emitting diodes = LEDs for limit position monitoring).
&
The two green LEDs indicate the limit positions of the
rotary piston. The red LED goes on in case of a
disturbance.
The conveying ratio and the switching cycles are entered into the control system
of the conveying control.
SM3-640
Observe the operating manual of the conveying control.
Functional description 26
SKW
4. Start-up
»
This chapter is intended for operating personnel.
Prerequisite for this chapter is general knowledge of the
operation of conveying units.
Also prerequisite for this chapter is that the functional
description has been read and understood.
Ensure in each case that the operating personnel are
sufficiently informed.
F
Check the compressed air supply (max. 6 bar system
overpressure). (87.02 PSI)
Check the connections of the conveying lines.
Check the suction pipe adjustment.
The SKW can only be operated in conjunction with a
conveying system.
SM3-640
&
Start-up 27
SKW
4.1. Adjusting the conveying ratio
Adjust the conveying ratio according to your specific requirements.
SKW Version 1
By means of the arrow key, set the percentage of
component 1 (= regrind).
Example
Desired conveying ratio: 40 % regrind and 60 % raw material.
Press the arrow key until “40" appears on the display.
F
When conveying poorly flowing components, set higher
values.
SKW Version 2
Set the percentage of component 1 (= regrind) by means of the control system of
the conveying control.
SM3-640
Observe the operating manual of the conveying control.
Start-up 28
SKW
4.2. Determining the switching cycle duration
Measure the conveying time of the respective hopper.
Take out the table.
Look for the value in the column “conveying time”.
Select a number of switching cycles.
Press the percentage key.
By means of the arrow key, select the desired switching cycle.
Carry through one conveying procedure.
If you are not satisfied with the result, check the setting and correct, if necessary.
F
No thick layers may form in the hopper loader.
Example
Conveying time: 50 s
Conveying ratio: 40 % regrind, 60 % virgin material
Setting options for a conveying time of 50 s:
SM3-640
Conveying
time
Number of switching cycles at cycle period (seconds)
(seconds)
50
45
40
35
30
25
20
15
10
5
50
1
1,1
1,3
1,4
1,7
2
2,5
3,3
5
10
a.) Setting 50 seconds = 1 switching cycle per conveying procedure
Start-up 29
SKW
The SKW switches twice; it conveys
regrind for 20 seconds and virgin
material for 30 seconds.
Significant zoning.
b.) Setting 10 = 5 switching cycles per
conveying procedure
The SKW switches ten times; it
conveys regrind for 4 seconds and
virgin material for 6 seconds.
SM3-640
Insignificant zoning.
Start-up 30
SKW
c.) Setting 5 = 10 switching cycles per conveying cycle
The SKW switches 20 times; it
conveys regrind for 2 seconds
and virgin material for 3 seconds.
This process is repeated 10
times.
No correct conveyance possible.
SM3-640
With a conveying time of 2 to 3
seconds the material cannot be
conveyed properly.
Start-up 31
SKW
4.3. Setting the switching cycles
SKW Version 1
Press the percentage key.
By means of the arrow key, set the determined switching cycle.
Check the result.
If the result is not satisfactory, correct the setting.
&
If there are too many switching cycles, proper conveying is
not possible.
SKW Version 2
Set the determined value by means of the control system of the conveying
control.
Observe the operating manual of the conveying control.
Check the result.
SM3-640
If the result is not satisfactory, correct the setting.
Start-up 32
SKW
5. Maintenance
»
This chapter is intended for persons with skills in electrical
and mechanical areas due to their training, experience and
received instructions.
Personnel using the instructions in this chapter must be
instructed of the regulations for the prevention of
accidents, the operating conditions and safety regulations
and their implementation.
Ensure in each case that the personnel are informed
accordingly.
For maintenance work taking place at heights of over
approx.1829 mm (6 ft), use only ladders or similar
equipment and working platforms intended for this
purpose. At greater heights, the proper equipment for
protection against falling must be worn.
Use only suitable lifting gear which is in proper working
order and load suspension devices with sufficient carrying
capacity. Do not stand or work under suspended loads!
Ensure that the electric motors/switch cabinets are
sufficiently protected against moisture.
Use only suitable workshop equipment.
SM3-640
Before starting maintenance work, appoint a supervisor.
Inform the responsible personnel before maintenance work
on the system is started.
Maintenance 33
SKW
Never operate the equipment when partially dismantled.
All maintenance and repair work not described in this
chapter may only be carried out by Sterlingservice
personnel or authorized personnel (appointed by Sterling).
L
Disconnect the equipment from mains supply before
starting maintenance procedures to ensure that it cannot
be switched on unintentionally.
Depressurize all compressed air piping of the equipment
before starting maintenance work.
F
Please observe the maintenance intervals.
Before starting maintenance work, clean the equipment of
oil, fuel or lubricants.
Ensure that materials and incidentals required for
operation as well as spare parts are disposed of properly
and in an environmentally sound manner.
Use only original Sterling spare parts.
SM3-640
Keep record of all maintenance and repair procedures.
Maintenance 34
SKW
5.1. Maintenance intervals
Daily:
Check warning signs on equipment for good
legibility and completeness.
Check the oil level in the oiler.
Empty the water separator.
Check operating pressure of the plant’s supply
network (5-6 bar (72.52-87.02 PSI) system over
pressure).
Every three months:
Check the SKW for smooth operation.
Every six months:
Check all electrical and mechanical connections
for secure fit.
SM3-640
F
In case of soiled material and material with a high dust
content equipment should be checked monthly for smooth
operation.
Maintenance 35
SKW
5.2. Checking for smooth operation
»
Disconnect the equipment from mains power supply to
ensure that it cannot be switched on unintentionally.
In order to check for smooth operation compressed air
supply to the SKW must be maintained.
Danger! Limbs may be caught in machinery!
Unscrew the plug at the solenoid valve.
Remove the hose from the hopper loader
outlet port.
Move the manual actuator of the solenoid
valve from position B to position A and
back
Observe the piston through the pipe
socket at the “hopper loader outlet port”.
The piston must move back and forth
quickly.
Put the hose at the hopper loader outlet
port back in place.
SM3-640
Screw the plug to the solenoid valve.
6. Technical data
Technical data 36
SKW
Versions:
SKW 40
SKW 50
SKW 65
SKW 40
Height:
305 mm (12.01 in.)
Width:
246 mm (10.79 in.)
Depth:
235 mm (9.35 in.)
Weight:
7.5 kg (16.53 lbs.)
Compressed air supply:
5-6 bar (72.52-87.02 PSI) system overpressure
Piping system:
Æ 40 mm (1.67 in.)
SKW 50
Height:
305 mm (12.01 in.)
Width:
256 mm (10.18 in.)
Depth:
235 mm (9.35 in.)
Weight:
7.5 kg (16.53 lbs.)
Compressed air supply:
5-6 bar (72.52-87.02 PSI) system overpressure
Piping system:
Æ 50 mm ((2.07 in.)
SKW 65
340 mm (13.49 in.)
Width:
290 mm (11.42 in.)
Depth:
245 mm (10.7 in.)
Weight:
12.5 kg (27.66 lbs.)
Compressed air supply:
5-6 bar (72.52-87.02 PSI) system overpressure
Piping system:
Æ 65 mm (0.36 in.)
SM3-640
Height:
Technical data 37
SKW
6.1. Dimension sheet SKW 40/50
All di mensions in mm. (in.) Specifications may be subject to al teration.
6.2. Dimension sheet SKW 65
SM3-640
(On next page)
Technical data 38
SKW
SM3-640
All di mensions in mm (in.). Specifications may be subject to al teration.
Technical data 39
SKW
SM3-640
7. Appendix
Appendix 40
SKW
7.1. Spare parts list
»
This spare parts list is intended to be used only by trained
personnel.
SM3-640
Other persons are not permitted to modify or repair the
equipment.
Appendix 41
18,31,32
8
7
4
3
2
1
SM3-640
25
12
24
23
5
16
20
15
28
27
6 bar
26
5 -
22
21
6
19
17
13
6
5
14
33
10
11
9
SKW
SKW 40 (03596)
Appendix 42
SKW
SM3-640
03596
Pos.
Orderno.
Designation
0001
03546
Housing
0002
03576
Piston
0003
96366
Deep groove ball bearing
0004
03575
Bearing lid
0005
95944
Spring lock washer
0006
95842
Screw
0007
96043
Screw
0008
95840
Threaded pin
0009
97706
Pipe socket
0010
96384
Sealingring
0011
95839
Threaded pin
0012
98167
Hose nozzle
0014
03573
Bend
0015
27603
Support
0016
95841
Screw
0018
96045
Screw
0019
96373
Rotary drive
0020
98753
Coupling piece
0021
96372
Solenoid valve
0022
95985
Screw
0023
98752
Coupling piece
0024
98742
Silencer
0025
03604
Bow
0026
95844
Screw
0027
95956
Disc
0028
98750
Hose
0029
95556
Screw
0031
95948
Disc
0032
93882
Nut
0033
15475
Sealing
Appendix 43
18,31,32
8
7
4
3
2
1
SM3-640
15
16
20
6
5
14
50
11
10
9
19
13
6
5 -
6 bar
28
27
26
25
12
24
23
5
22
21
17
SKW
SKW 50 (03597)
Appendix 44
SKW
SM3-640
03597
Pos.
Orderno.
Designation
0001
03547
Housing
0002
03576
Piston
0003
96366
Deep groove ball bearing
0004
03575
Bearing lid
0005
95842
Screw
0007
96043
Screw
0008
95840
Threaded pin
0009
97704
Pipe socket
0010
96383
Sealingring
0011
95839
Threaded pin
0012
98167
Hose nozzle
0013
95955
Disc
0014
03574
Bend
0015
27603
Support
0016
95841
Screw
0018
96045
Screw
0019
96373
Rotary drive
0020
98753
Coupling piece
0021
96372
Solenoid valve
0022
95985
Screw
0023
98752
Coupling piece
0024
98742
Silencer
0025
03604
Bow
0026
95844
Screw
0027
95956
Disc
0028
98750
Hose
0031
95948
Disc
0032
93882
Nut
0033
15476
Sealing
Appendix 45
4
3
50
2
51
SM3-640
8
14
1
9
7
6
5
20
19
18,31,32
17
28
27
26
25
12
24
23
5
22
16
5 - 6 bar
21
15
6
13
SKW
SKW 65 (12446)
Appendix 46
SKW
SM3-640
12446
Pos.
Orderno.
Designation
0001
12416
Housing
0002
12418
Piston
0003
92226
Deep groove ball bearing
0004
12417
Bearing lid
0005
95944
Spring lock washer
0006
95842
Screw
0007
96043
Screw
0008
95840
Threaded pin
0009
17208
Pipe socket
0012
98167
Hose nozzle
0013
95955
Disc
0014
12414
Bend
0015
27603
Support
0016
95841
Screw
0017
99931
Cable
0018
96045
Screw
0019
96373
Rotary drive
0020
98753
Coupling piece
0021
96372
Solenoid valve
0022
95985
Screw
0023
98752
Coupling piece
0024
98742
Silencer
0025
03604
Bow
0026
95844
Screw
0027
95956
Disc
0028
98750
Hose
0031
95948
Disc
0032
93882
Nut
0050
15477
Sealing
0051
88141
Sealing
Appendix 47
36
29
38,40
8
7
6
5
4
3
37
2
1
SM3-640
39
33
14
50
10
11
9
20
19
35
41
42
13
6
5 - 6 bar
34
28
27
26
12
24
23
5
22
21
17
SKW
CLV 40 (10102)
Appendix 48
SKW
SM3-640
10102
Pos.
Orderno.
Designation
0001
03546
Housing
0002
09518
Piston with final switch position check
0003
96366
Deep groove ball bearing
0004
09519
Bearing lid with final switch position check
0005
95944
Spring lock washer
0006
95842
Screw
0007
96043
Screw
0008
95840
Threaded pin
0009
97706
Pipe socket
0010
96384
Sealingring
0011
95839
Threaded pin
0012
98167
Hose nozzle
0013
95957
Disc
0014
03573
Bend
0017
99931
Cable
0019
96373
Rotary drive
0020
98753
Coupling piece
0021
96372
Solenoid valve
0022
95985
Screw
0023
98752
Coupling piece
0024
98742
Silencer
0026
95844
Screw
0027
95956
Disc
0028
98750
Hose
0029
96038
Screw
0033
97763
Conical caps
0034
92477
3-wire -initiator with LED
0035
88071
Screw
0036
11503
Nozzle
0037
93228
Sieve
Appendix 49
SKW
11122
Housing
0039
99944
Coupling piece
0040
92470
SKW-MLV control card
0041
98609
Coupling piece
0042
93075
Welsh plug
0050
15475
Sealing
0051
85982
Distance bolt
0052
95946
Spring lock washer
0053
95970
Nut
SM3-640
0038
Appendix 50
SKW
SM3-640
Connection diagram
Appendix 51
Number of switching cycles at cycle period (seconds)
Conveying
time
(seconds)
50
45
40
35
30
25
20
15
10
5
5
*
*
*
*
*
*
*
*
*
1
10
*
*
*
*
*
*
*
*
1
2
15
*
*
*
*
*
*
*
1
1,5
3
20
*
*
*
*
*
*
1
1,3
2
4
25
*
*
*
*
*
1
1,3
1,7
2,5
5
30
*
*
*
*
1
1,2
1,5
2
3
6
35
*
*
*
1
1,2
1,4
1,8
2,3
3,5
7
40
*
*
1
1,1
1,3
1,6
2
2,7
4
8
45
*
1
1,1
1,3
1,5
1,8
2,3
3
4,5
9
50
1
1,1
1,3
1,4
1,7
2
2,5
3,3
5
10
55
1,1
1,2
1,4
1,6
1,8
2,2
2,8
3,7
5,5
11
60
1,2
1,3
1,5
1,7
2
2,4
3
4
6
12
65
1,3
1,4
1,6
1,9
2,2
2,6
3,3
4,3
6,5
13
70
1,4
1,5
1,8
2
2,3
2,8
3,5
4,7
7
14
75
1,5
1,7
1,9
2,1
2,5
3
3,8
5
7,5
15
80
1,6
1,8
2
2,3
2,7
3,2
4
5,3
8
16
85
1,7
1,9
2,1
2,4
2,8
3,4
4,3
5,7
8,5
17
90
1,8
2
2,3
2,6
3
3,6
4,5
6
9
18
95
1,9
2,1
2,4
2,7
3,2
3,8
4,8
6,3
9,5
19
100
2
2,2
2,5
2,9
3,3
4
5
6,7
10
20
105
2,1
2,3
2,6
3
3,5
4,2
5,3
7
10,5
21
110
2,2
2,4
2,8
3,1
3,7
4,4
5,5
7,3
11
22
115
2,3
2,6
2,9
3,3
3,8
4,6
5,8
7,7
11,5
23
3
3,4
4
4,8
6
8
12
24
2,4
2,7
120
* = Setting not permitted