Alliance Laundry Systems 100 Washer User Manual

Installation
Washer-Extractors
Cabinet Freestanding
Refer to Page 6 for Model Identification
CFD15C
33, 40, 55 and 75 Models
CFD19C
CFD19C
18, 25 and 35 Models
CFD20C
CFD20C
100, 135, 165 and 200 Models
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9001000R13
www.comlaundry.com
July 2010
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
2
2
2
4
5
Introduction.........................................................................................
Model Identification .............................................................................
Nameplate Location..............................................................................
Replacement Parts ................................................................................
Customer Service..................................................................................
6
6
8
8
8
Specifications and Dimensions........................................................... 10
Installation...........................................................................................
Dimensional Clearances...................................................................
Machine Foundation ........................................................................
Mechanical Installation.........................................................................
Frame Dimensions and Mounting Bolt Location.............................
Mounting Bolt Installation (If Required)..............................................
Removing the Transport Brackets ........................................................
Drain Connection..................................................................................
Water Connection .................................................................................
Electrical Installation ............................................................................
Electrical Connection............................................................................
Remote Liquid Supply Connection ......................................................
Chemical Injection Supply System ..................................................
Steam Requirements (Steam Heat Option Only)..................................
Supply Programming Table .............................................................
Supply Relay Configuration (No Wiring)........................................
Primary 220 Volt Remote Liquid Supply Connection.....................
Out-of-Balance Switch .........................................................................
Automatic Lubricator............................................................................
Control Function Test ...........................................................................
25
25
26
27
27
41
42
44
46
47
50
50
50
51
52
52
52
54
54
55
© Copyright 2010, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Safety Information
Operator Safety
Do not bypass any safety devices in the machine.
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Introduction
Model Identification
Information in this manual is applicable to these
models:
HX18PVQM6
HX18PVQM7
HX18PVXM6
HX18PVXM7
SX18PVPA7
SX18PVQM6
SX18PVQM7
SX18PVXM6
SX18PVXM7
HX25PVQM6
HX25PVQM7
HX25PVXM6
HX25PVXM7
SX25PVQM6
SX25PVQM7
SX25PVXM6
SX25PVXM7
18
25
UX18PVNA6
UX18PVNA7
UX18PVPA6
UX18PVPA7
UX18PVQA6
UX18PVQA7
UX18PVQM6
UX18PVQM7
UX18PVXA6
UX18PVXA7
UX18PVXM6
UX18PVXM7
UX25PVNA6
UX25PVNA7
UX25PVPA6
UX25PVPA7
UX25PVQA6
UX25PVQA7
UX25PVQM6
UX25PVQM7
UX25PVXA6
UX25PVXA7
UX25PVXM6
UX25PVXM7
HX18PVQU6
HX18PVXU6
SX18PVQU6
SX18PVXU6
UX18PVNU6
UX18PVPU6
UX18PVQU6
UX18PVXU6
HX25PVQU6
HX25PVXU6
SX25PVQU6
SX25PVXU6
UX25PVNU6
UX25PVPU6
UX25PVQU6
UX25PVXU6
33
HX35PVQM6
HX35PVQM7
HX35PVXM6
HX35PVXM7
35
SX35PVQM6
SX35PVQM7
SX35PVXM6
SX35PVXM7
SX35PVNM7
UX35PVNA6
UX35PVNA7
UX35PVPA6
UX35PVPA7
UX35PVQA6
UX35PVQA7
UX35PVQM6
UX35PVQM7
UX35PVXA6
UX35PVXA7
UX35PVXM6
UX35PVXM7
HX35PVQU6
HX35PVXU6
SX35PVQU6
SX35PVXU6
UX33PVNA7
UX33PVPA7
UX33PVQA7
UX33PVQM7
UX33PVXA7
UX33PVXM7
UX35PVNU6
UX35PVPU6
UX35PVQU6
UX35PVXU6
continued
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Introduction
continued
40
55
75
100
135
165
200
9001000
HX55PVNU6
HX55PVNU7
HX55PVQU6
HX55PVQU7
HX55PVXU6
HX55PVXU7
HX75PVNU6
HX75PVNU7
HX75PVPU7
HX75PVQU6
HX75PVQU7
SX55PVNU6
SX55PVNU7
SX55PVPU6
SX55PVPU7
SX55PVQU6
SX55PVQU7
SX55PVXU6
SX55PVXU7
SX75PVNU6
SX75PVNU7
SX75PVPU7
SX75PVQU6
SX75PVQU7
HX100PVNU6
HX100PVNU7
HX100PVPU7
HX100PVQU6
HX100PVQU7
SX100PVNU6
SX100PVNU7
SX100PVPU7
SX100PVQU6
SX100PVQU7
HX135PVNU6
HX135PVNU7
HX135PVPU7
HX135PVQU6
HX135PVQU7
SX135PVNU6
SX135PVNU7
SX135PVPU7
SX135PVQU6
SX135PVQU7
HX165PVNU6
HX165PVNU7
HX165PVPU7
HX165PVQU6
HX165PVQU7
SX165PVNU6
SX165PVNU7
SX165PVPU7
SX165PVQU6
SX165PVQU7
HX200PVNU7
HX200PVPU7
HX200PVQU7
SX200PVNU7
SX200PVPU7
SX200PVQU7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
UX40PVNA7
UX40PVPA7
UX40PVQA7
UX40PVQM7
UX40PVXA7
UX40PVXM7
UX55PVNU6
UX55PVNU7
UX55PVPU6
UX55PVPU7
UX55PVQU6
UX55PVQU7
UX55PVXU6
UX55PVXU7
UX75PVNU6
UX75PVNU7
UX75PVPU6
UX75PVPU7
UX75PVQU6
UX75PVQU7
UX100PVNU6
UX100PVNU7
UX100PVPU6
UX100PVPU7
UX100PVQU6
UX100PVQU7
UX135PVNU6
UX135PVNU7
UX135PVPU6
UX135PVPU7
UX135PVQU6
UX135PVQU7
UX165PVNU6
UX165PVNU7
UX165PVPU6
UX165PVPU7
UX165PVQU6
UX165PVQU7
UX200PVNU7
UX200PVPU7
UX200PVQU7
7
Introduction
Nameplate Location
The nameplate is located at the rear of the machine.
Always provide the machine’s serial number and
model number when ordering parts or when seeking
technical assistance.
1
1
1
CFD15C
CFD19CCFD19C
CFD20C
CFD20C
18, 25 AND 35 MODELS
1
33, 40, 55 AND 75 MODELS
100, 135, 165 AND 200 MODELS
Nameplate
Figure 1
Replacement Parts
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
Customer Service
For technical assistance, call (920) 748-3121.
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Introduction
Model Number Familiarization Guide
Sample Model Number: *X55PVXM60001
*X
Model Number Prefix
55
Washer-Extractor Capacity (pounds dry weight of laundry)
P
Type of Electrical Control (P = WE-6 Computer)
V
Washer-Extractor Speed Capabilities
X
Electrical Characteristics
M6
0001
Design Series
Option Identification (varies from machine to machine)
* Denotes Brand
* X55PVXM60001
12
50 60
55
15
2/3+PE
25
1/3
1000
EXAMPLE OF NAMEPLATE
CFD29N
CFD29N
Figure 2
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Specifications and Dimensions
General Specifications
Model
18
25
33
35
40
Overall width
26 in.
(660 mm)
26 in.
(660 mm)
30.71 in.
(780 mm)
30.8 in.
(783 mm)
30.71 in.
(780 mm)
Overall height
40.6 in.
(1031 mm)
40.6 in.
(1031 mm)
54.15 in.
(1376 mm)
47 in.
(1194 mm)
54.15 in.
(1376 mm)
Overall depth
30.7 in.
(780 mm)
34.3 in.
(870 mm)
33.07 in.
(840 mm)
37.8 in.
(960 mm)
37.01 in.
(940 mm)
Net weight †
465 lb.
(211Kg)
520 lb.
(236 Kg)
811.30 lb.
(368 Kg)
789 lb.
(358 Kg)
862.01 lb.
(391 Kg)
Net weight ††
520 lb.
(236 kg)
531 lb.
(241 kg)
N/A
765 lb.
(347 kg)
N/A
Shipping weight †
514 lb.
(233 Kg)
569 lb.
(258 Kg)
844.37 lb.
(383 Kg)
855 lb.
(388 Kg)
921.53 lb.
(418 Kg)
Shipping weight ††
624 lb.
(283 kg)
639.5 lb.
(290 kg)
N/A
1030 lb.
(467 kg)
N/A
Shipping volume
22.5 ft3
(0.8 m3)
24.5 ft3
(0.9 m3)
42.83 ft3
(1.21 m3)
34.7 ft3
(1.3 m3)
45.98 ft3
(1.3 m3)
Cylinder diameter
20.9 in.
(530 mm)
20.9 in.
(530 mm)
26.77 in.
(680 mm)
25.6 in.
(650 mm)
26.77 in.
(680 mm)
Cylinder depth
13.6 in.
(345 mm)
17.3 in.
(440 mm)
15.75 in.
(400 mm)
19.7 in.
(500 mm)
19.69 in.
(500 mm)
Cylinder volume
2.7 ft3
(76 l)
3.43 ft3
(97 l)
5.12 ft3
(145 l)
5.9 ft3
(167 l)
6.39 ft3
(181 l)
Perforation size
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
11.8 in.
(300 mm)
11.8 in.
(300 mm)
15.75 in.
(400 mm)
11.8 in.
(300 mm)
15.75 in.
(400 mm)
11 in.
(279 mm)
11 in.
(279 mm)
18.58 in.
(472 mm)
15.6 in.
(395 mm)
18.58 in.
(472 mm)
Overall Dimensions
Weight and Shipping Information
Wash Cylinder Information
Door Opening Information
Door opening size
Height of door bottom above floor
† For Models with A or M in the 8th position in the model number (e.g. *X18PVXA6)
†† For Models with U in the 8th position in the model number (e.g *X18PVXU6)
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
General Specifications
Model
18
25
33
35
40
1
1
1
1
1
1 HP
(0.75 kW)
1 HP
(0.75 kW)
2.95 HP
(2.2 kW)
2 HP
(1.5 kW)
2.95 HP
(2.2 kW)
10-50 RPM
10-50 RPM
10-50 RPM
10-50 RPM
10-50 RPM
82 RPM
82 RPM
85 RPM
74 RPM
85 RPM
Drive Train Information
Number of motors in drive train
Drive motor power
Cylinder Speeds
Wash/reverse speed
Distribution/drain speed
Extract speed
250-1000 RPM 250-1000 RPM 250-1000 RPM 250-1000 RPM 250-1000 RPM
Centrifugal Force Data
Wash/reverse centrifugal force
0.03-0.74 Gs
0.03-0.74 Gs
0.37-0.94 Gs
0.04-0.91 Gs
0.37-0.94 Gs
19-296 Gs
19-296 Gs
24-377 Gs
23-363 Gs
24-377 Gs
Standard
Standard
Standard
Standard
Standard
0.38 in.
(10 mm)
0.38 in.
(10 mm)
.375 in.
(10 mm)
0.38 in.
(10 mm)
.375 in.
(10 mm)
1
1
1
1
1
9 kW
9 kW
18 kW
18 kW
18 kW
Electrical heating elements
3
3
6
6
6
Electrical heat element size
3 kW
3 kW
3 kW
3 kW
3kW
Extract centrifugal force
Balance Detection
Vibration safety switch installed
Direct Steam Heating (Optional)
Steam inlet connection size
Number of steam inlets
Electrical Heating (Optional)
Total electrical heating capacity
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Specifications and Dimensions
General Specifications
Model
55
75
100
135
165
200
Overall width
35.4 in.
(900 mm)
41.8 in.
(1060 mm)
47.3 in.
(1200 mm)
47.3 in.
(1200 mm)
51.8 in.
(1300 mm)
51.8 in.
(1300 mm)
Overall height
60.8 in.
(1544 mm)
61.4 in.
(1560 mm)
75.6 in.
(1920 mm)
75.6 in.
(1920 mm)
82.7 in.
(2100 mm)
82.68 in.
(2100 mm)
Overall depth
40 in.
(1016 mm)
46 in.
(1168 mm)
52.4 in.
(1330 mm)
59.1 in.
(1500 mm)
63.8 in.
(1620 mm)
71.18 in.
(1808 mm)
Overall Dimensions
Weight and Shipping Information
Net weight
1247 lb.
(570 kg)
1907 lb.
(865 kg)
3351 lb.
(1520 kg)
3626 lb.
(1645 kg)
4630 lb.
(2100 kg)
6393.41 lb.
(2900 kg)
Shipping weight
1380 lb.
(630 kg)
2194 lb.
(995 kg)
3741 lb.
(1697 kg)
4017 lb.
(1822 kg)
5113 lb.
(2319 kg)
6613.86 lb.
(3000 kg)
Shipping volume
54.9 ft3
(1.5 m3)
74 ft3
(2.1 m3)
115 ft3
(3.3 m3)
131 ft3
(3.7 m3)
162 ft3
(4.4 m3)
217.89 ft3
(6.17 m3)
Cylinder diameter
29.5 in.
(750 mm)
33.5 in.
(850 mm)
38.6 in.
(980 mm)
38.6 in.
(980 mm)
43.1 in.
(1095 mm)
43.11 in.
(1095 mm)
Cylinder depth
20.9 in.
(530 mm)
21.1 in.
(537 mm)
23.5 in.
(597 mm)
30.5 in.
(775 mm)
30.5 in.
(775 mm)
37.68 in.
(957 mm)
Cylinder volume
8.27 ft3
(234 l)
10.76 ft3
(305 l)
15.92 ft3
(451 l)
20.66 ft3
(585 l)
25.8 ft3
(730 l)
31.748 ft3
(9001 l)
Perforation size
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
0.1 in.
(3 mm)
Door opening size
15.6 in.
(395 mm)
15.6 in.
(395 mm)
19.7 in.
(500 mm)
19.7 in.
(500 mm)
24.5 in.
(622 mm)
24.5 in.
(622 mm)
Height of door bottom above
floor
22 in.
(559 mm)
22 in.
(559 mm)
25.5 in.
(648 mm)
25.5 in.
(648 mm)
28 in.
(710 mm)
23.74 in.
(603 mm)
Wash Cylinder Information
Door Opening Information
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
General Specifications
Model
55
75
100
135
165
200
1
1
1
1
1
1
4 HP
(3 kW)
5.4 HP
(4 kW)
7.4 HP
(5.5 kW)
10 HP
(7.5 kW)
15 HP
(11.5 kW)
20 HP
(15 kW)
Drive Train Information
Number of motors in drive train
Drive motor power
Cylinder Speeds
Wash/reverse speed
10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM
Distribution/drain speed
69 RPM
65 RPM
61 RPM
61 RPM
100 RPM
80 RPM
Extract speed
250-1000
RPM
250-1000
RPM
250-800
RPM
250-800
RPM
250-750
RPM
250-750
RPM
Wash/reverse centrifugal force
0.04-1.05
Gs
0.05-1.19
Gs
0.06-1.37
Gs
0.06-1.37
Gs
0.06-1.52
Gs
0.06-1.52
Gs
Extract centrifugal force
26-418 Gs 30-475 Gs 34-350 Gs 34-350 Gs
34-344 Gs
34-342 Gs
Centrifugal Force Data
Balance Detection
Vibration safety switch installed
Standard
Standard
Standard
Standard
Standard
Standard
0.38 in.
(10 mm)
0.38 in.
(10 mm)
0.38 in.
(10 mm)
0.38 in.
(10 mm)
0.75 in.
(19 mm)
0.75 in.
(19 mm)
1
1
1
1
1
1
18 kW
18 kW
27 kW
27 kW
N/A
36 kW
Electrical heating elements
6
6
9
9
N/A
9
Electrical heat element size
3 kW
3 kW
3 kW
3 kW
N/A
4 kW
Direct Steam Heating (Optional)
Steam inlet connection size
Number of steam inlets
Electrical Heating (Optional)
Total electrical heating capacity
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Specifications and Dimensions
5
18: 31 in. (787 mm)
25: 34.8 in. (884 mm)
40.6 in.
(1031 mm)
39.8 in.
(1011 mm)
20.4 in.
(518 mm)
11 in.
(279 mm)
19.13 in.
(486 mm)
18: 22.05 in.
(560 mm)
26 in.
(660 mm)
25: 25.98 in.
(660 mm)
CFD530N
CFD530 N
9 in.
(229 mm)
8
6 in.
(152 mm)
2.9 in.
(74 mm)
4
CFS464N
CFS464N
1
5.5 in.
(140 mm)
2 3
7
6
10
6.2 in.
(158 mm)
30.7 in.
(780 mm)
29.2 in.
(742 mm)
34.7 in.
(881 mm)
9
1.6 in.
(41 mm)
15.3 in.
(389 mm)
2 in.
(51 mm)
7.1 in.
(181 mm)
CFS465N
CFS465N
18 and 25 Pound Capacity Models with U in the
1
2
3
4
5
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
6
7
8
9
10
8th
Position (e.g. *X18PVXU6)
External Liquid Supply Inlets
Electrical Power Input
External Supply Signal Input
Drain Outlet
Steam Connection Input (Optional)
Figure 3
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
8.66 in.
(220 mm)
10.98 in.
(279 mm)
39.8 in. (1011 mm)
40.87 in. (1038 mm)
11
1.3 in.
(33 mm)
2.56 in.
(65 mm)
1.3 in.
(33 mm)
2.56 in.
(65 mm)
20.87 in. (530 mm)
25.98 in. (660 mm)
1.18 in.
(30 mm)
18: 26.38 in. (670 mm)
25: 30.31 in. (770 mm)
CFD521N
CFD521N
8.9 in. (226 mm)
5.94 in. (151 mm)
1
2.95 in. (75 mm)
2
3
4
18: 23.23 in. (590 mm)
25: 27.17 in. (690 mm)
2.72 in.
(69 mm)
18: 28.62 in. (727 mm)
25: 32.56 in. (827 mm)
5
10
1.18 in.
(30 mm)
CFD522N
CFD522N
6
9
8
4.3 in.
(109 mm)
7.09 in. (180 mm)
25.98 in. (660 mm)
2.76 in. (70 mm)
27.41 in. (696.2 mm)
34.92 in. (887 mm)
31.14in. (791 mm)
29.41 in. (747 mm)
19.1 in. (485 mm)
7
1.73 in.
(44 mm)
CFD528N
CFD528N
18 and 25 Pound Capacity Models with A or M in the 8th Position (e.g. *X18PVXM6)
1
2
3
4
5
6
Fill and Supply Ventilation
Cold Water Inlet (Required)
External Liquid Supply Inlets
Hot Water Inlet (Required)
Ventilation Tub
Main Switch
7
8
9
10
11
Electrical Power Input
Drain Outlet
Steam Connection Input (Optional)
Cold Water Inlet (Required)
Flushing Supply Dispenser
Figure 4
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Specifications and Dimensions
3.47 in.
(88 mm)
18.58 in. (472 mm)
54.15 in. (1376 mm)
53.07 in. (1348 mm)
8.66 in.
(220 mm)
26.77 in. (680 mm)
1.97 in.
(50 mm)
1.97 in.
(50 mm)
30.71 in. (780 mm)
1.34 in.
(34 mm)
3.41 in.
(86.5 mm)
CFD537N
CFD537N
13.05 in. (332 mm)
10.49 in. (267 mm)
7.93 in. (202 mm)
4.13 in. (105 mm)
1
2
4
26.18 in. (665 mm)
28.86 in. (733 mm)
29.65 in. (753 mm)
1.34 in.
(34 mm)
CFD538N
CFD538N
3
5
6
7
10
1.38 in.
(35 mm)
4.3 in.
(109 mm)
7.29 in. (185 mm)
39.96 in. (1015 mm)
44.9 in. (1141 mm)
43.6 in. (1108 mm)
41.95 in. (1066 mm)
27.7 in. (704 mm)
8
9
6.69 in. (170 mm)
CFD539N
CFD539N Models
33 Pound Capacity
1
2
3
4
5
Fill and Supply Ventilation
External Liquid Supply Inlets
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Hot Water Inlet (Required)
6
7
8
9
10
Connection Clamps
Ventilation Tub
Electrical Power Inputs
Drain Valve
Steam Connection Input (Optional)
Figure 5
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
5
37.8 in.
(960 mm)
47 in.
(1194 mm)
46.3 in.
(1176 mm)
24.4 in.
(620 mm)
15.5 in.
(394 mm)
25.16 in.
(639 mm)
30.31 in.
(770 mm)
30.8 in.
(782 mm)
CFD531N
CFD531N
CFS467N
CFS467N
12.9 in.
(328 mm)
10.4 in.
(264 mm)
3.5 in.
(89 mm)
8
2
3
4
1
6.1 in.
(155 mm)
7
6
10
41 in.
(1041 mm)
36.75 in.
(934 mm)
38 in.
(965 mm)
39.4 in.
(1001 mm)
35 in.
(889 mm)
9
20 in.
(508 mm)
4.4 in.
(112 mm)
8 in.
(203 mm)
CFS468N
35 Pound Capacity Models with U in the 8th Position (e.g. *X35PVXU6)
1
2
3
4
5
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
6
7
8
9
10
External Liquid Supply Inlets
Electrical Supply Signal Input
External Supply Signal Input
Drain Outlet
Steam Connection Input (Optional)
Figure 6
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Specifications and Dimensions
11
8.66 in.
(220 mm)
14.78 in.
(376 mm)
47.32 in. (1202 mm)
46.3 in. (1176 mm)
3.47 in.
(88 mm)
1.34 in.
(34 mm)
2.6 in.
(66 mm)
1.34 in.
(34 mm)
25.51 in. (648 mm)
30.71 in.(780 mm)
2.6 in.
(66 mm)
CFD524N
CFD524N
13.05 in. (332 mm)
10.49 in. (267 mm)
7.93 in. (202 mm)
4.13 in. (105 mm)
9
1.44 in.
(36.5 mm)
30.12 in. (765 mm)
33.86 in. (860 mm)
3.23 in.
82 mm)
36.06 in. (916 mm)
1.44 in.
(36.5 mm)
CFD525N
CFD525N
1
3
2
10
4
5
8
6
4.3 in.
(109.2 mm)
7
7.87 in.
(200 mm)
33.17 in. (843 mm)
2.76 in. (70 mm)
38.11 in. (968 mm)
36.81 in. (935 mm)
35.16 in. (893 mm)
20.87 in. (530 mm)
1.38 in (35 mm)
2.36 in.
(60 mm)
CFD529N
CFD529N
35 Pound Capacity Models with A or M in the 8th Position (e.g. *X35PVXM6)
1
2
3
4
5
6
Fill and Supply Ventilation
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Main Switch
Ventilation Tub
Electrical Power Input
7
8
9
10
11
Drain Outlet
Steam Connection Input (Optional)
External Liquid Supply Inlets
Cold Water Inlet (Required)
Flushing Supply Dispenser
Figure 7
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
3.47 in.
(88 mm)
18.58 in. (472 mm)
54.15 in. (1376 mm)
53.07 in. (1348 mm)
8.66 in.
(220 mm)
26.77 in. (680 mm)
1.97 in.
(50 mm)
1.97 in.
(50 mm)
30.71 in. (780 mm)
1.34 in.
(34 mm)
3.41 in.
(86.5 mm)
CFD537N
CFD537N
13.05 in. (332 mm)
10.49 in. (267 mm)
7.93 in. (202 mm)
4.13 in. (105 mm)
1
2
4
30.12 in. (765 mm)
32.8 in. (833 mm)
33.58 in. (853 mm)
1.34 in.
(34 mm)
CFD538N
CFD538N
3
5
6
10
7
1.38 in.
(35 mm)
4.3 in.
(109 mm)
7.29 in. (185 mm)
39.96 in. (1015 mm)
44.9 in. (1141 mm)
43.6 in. (1108 mm)
41.95 in. (1066 mm)
27.7 in. (704 mm)
8
9
6.69 in. (170 mm)
CFD539N
CFD539N Models
40 Pound Capacity
1
2
3
4
5
Fill and Supply Ventilation
External Liquid Supply Inlets
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Hot Water Inlet (Required)
6
7
8
9
10
Connection Clamps
Ventilation Tub
Electrical Power Inputs
Drain Valve
Steam Connection Input (Optional)
Figure 8
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Specifications and Dimensions
5
40 in.
(1016 mm)
60.8 in.
(1544 mm)
59 in.
(1499 mm)
33.8 in.
(859 mm)
22 in.
(559 mm)
29.13 in.
(740 mm)
35.43 in.
(900 mm)
32.68 in.
(830 mm)
4 in.
(102 mm)
CFS470N
CFD509N
CFS470N
CFD509N
13.6 in.
(91 mm)
10 in.
(254 mm)
9.9 in.
(252 mm)
6.2 in.
(158 mm)
2
3
4
3.9 in.
(99 mm)
1
6
7.5 in.
(191 mm)
54.7 in.
(1389 mm)
11
50.5 in.
(1283 mm)
8
7
1.4 in.
(36 mm)
28.4 in.
(721 mm)
6.5 in.
(165 mm)
6.5 in.
(165 mm)
9
10
4.1 in.
4.1 in. (104 mm)
(104 mm)
CFS471N
CFS471N
55 MODEL
1
2
3
4
5
6
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
7
8
9
10
11
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Figure 9
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
5
46 in.
(1168 mm)
62 in.
(1575 mm)
60.3 in.
(1532 mm)
33.6 in.
(853 mm)
22 in.
(559 mm)
4 in.
(102 mm)
34.25 in.
(870 mm)
CFD510N
41.73 in.
(1060 mm)
37.8 in.
(960 mm)
19.2 in.
(488 mm)
CFD510N
CFS473N
CFS473N
14.4 in.
(366 mm)
9.7 in.
(246 mm)
2
9 in.
(229 mm)
3 4
3.7 in.
(94 mm)
1
6.9 in.
(175 mm)
6
55.4 in.
(1407 mm)
7
11
51.75 in.
(1315 mm)
8
1.7 in.
(43 mm)
22.9 in.
(582 mm)
6.7 in.
(170 mm)
10
9
4.1 in.
(104 mm)
CFS474N
CFS474N
4.1 in.
(104 mm)
75 MODEL
1
2
3
4
5
6
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
7
8
9
10
11
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Figure 10
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Specifications and Dimensions
100: 52.4 in. (1331 mm)
135: 59.3 in. (1506 mm)
6
76.8 in.
(1951 mm)
37.8 in.
(960 mm)
25.5 in.
(648 mm)
4 in.
(102 mm)
40.94 in.
(1040 mm)
47.24 in.
(1200 mm)
CFD511N
CFD511N
100: 39.76 in.
(1010 mm)
12 in.
(305 mm)
9.3 in.
(2362 mm)
135: 46.65 in.
(1185 mm)
CFS476N
CFS476N
6.9 in.
(175 mm)
3.5 in.
(89 mm)
4.5 in.
(114 mm)
4.1 in.
(104 mm)
6.5 in.
(165 mm)
2
3
5
6.7 in.
(170 mm)
2 in.
(51 mm)
9.8 in.
(249 mm)
1
8.7 in.
(221 mm)
4
9
7
62 in.
(1575 mm)
13
12
8
10
27.4 in.
(696 mm)
8.5 in.
(216 mm)
11
1
2
3
4
5
6
7
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
100 AND 135 MODELS
8
9
10
11
12
13
8.5 in.
(216 mm)
7.3 in.
(185 mm)
CFS477N
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Service Power Disconnect
Figure 11
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Specifications and Dimensions
63.8 in.
(1620 mm)
6
82.7 in.
(2100 mm)
40.2 in.
(1020 mm)
25.25 in.
(641 mm)
44.9 in.
(1140 mm)
51.2 in.
(1300 mm)
4 in.
(102 mm)
CFD511N
CFD511N
14.25 in.
(360 mm)
10.75 in.
(273 mm)
46.7 in.
(1185 mm)
7.8 in.
(198 mm)
CFD15N
CFD15N
4.8 in.
(122 mm)
4.5 in.
(114 mm)
4.5 in.
(114 mm)
2
6.75 in.
(172 mm)
2 in.
(51 mm)
7.75 in.
(197 mm)
3 5
10.24 in.
(260 mm)
1
8.7 in.
(221 mm)
4
9
7
73 in.
(1854 mm)
13
12
8
10
27.4 in.
(696 mm)
10 in.
(254 mm)
11
1
2
3
4
5
6
7
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
165 MODEL
8
9
10
11
12
13
10 in.
(254 mm)
9.3 in.
(236 mm)
CFS477N
Electrical Power Input
External Supply Signal Input
Drain Outlet (Standard)
Dual Drain Outlet (Optional)
Steam Connection Input (Optional)
Service Power Disconnect
Figure 12
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Specifications and Dimensions
6
2.23 in.
(56.5 mm)
82.7 in.
(2100 mm)
39 in.
(993 mm)
23.75 in.
(603 mm)
3.19 in.
(81 mm)
44.8 in.
(1138 mm)
1.73 in.
(44 mm)
10.71 in.
(272 mm)
3.19 in.
(81 mm)
51.18 in.
(1300 mm)
53.74 in.
(1365 mm)
57.2 in.
(1453 mm)
1.73 in.
(44 mm)
1.04 in.
(26.5 mm)
68.96 in.
(175.2 mm)
CFD534N
CFD533N
CFD533N
CFD534N
16.06 in.
(408 mm)
12.72 in.
(323 mm)
9.76 in.
(248 mm)
6.81 in.
(173 mm)
6.67 in.
(169.5 mm)
23
10.12 in.
(257 mm)
19.13 in.
(486 mm)
10.31 in.
(262 mm)
9.33 in.
(237 mm)
6.97 in.
(117 mm)
4.61 in.
(117 mm)
5
7 4
1
9
13
8
3.19 in.
(81 mm)
10
12
35.37 in.
(899.5)
6.85 in.
(174 mm)
10.24 in.
(260 mm)
1
2
3
4
5
6
7
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
11
200 MODEL
8
9
10
11
12
13
10.24 in.
(260 mm)
CFD535N
Electrical Power Input
External Supply Signal Input
Drain Outlet (Standard)
Dual Drain Outlet (Optional)
Steam Connection Input (Optional)
Service Power Disconnect
Figure 13
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Dimensional Clearances
Table 1 shows recommended minimum clearances on
all sides of the washer-extractor.
Recommended Minimum Clearances
Model
Minimum rear
clearance
18
25
33
35
40
55
75
100
135
165
200
24 in.
24 in.
24 in.
24 in.
24 in.
24 in.
24 in.
24 in.
24 in.
24 in.
24 in.
(600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm)
Minimum
6 in.
6 in.
6 in.
6 in.
6 in.
6 in.
6 in.
6 in.
6 in.
6 in.
6 in.
clearance between
(150 mm) (150 mm) (150 mm) (150 mm) (150 mm) (150 mm) (150 mm) (150 mm) (150 mm) (150 mm) (150 mm)
machine and wall
Minimum
1.2 in.
clearance between
(30 mm)
machines (side)
Minimum front
clearance (door
swing)
1.2 in.
1.2 in.
(30 mm) (30 mm)
1.2 in.
(30 mm)
1.2 in.
1.2 in.
1.2 in.
1.2 in.
1.2 in.
1.2 in.
1.2 in.
(30 mm) (30 mm) (30 mm) (30 mm) (30 mm) (30 mm) (30 mm)
16.5 in. 16.5 in.
21 in.
16.5 in.
21 in.
21 in.
21 in.
26 in.
26 in.
26 in.
26 in.
(419 mm) (419 mm) (533 mm) (419 mm) (533 mm) (533 mm) (533 mm) (660 mm) (660 mm) (660 mm) (660 mm)
Table 1
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Installation
Machine Foundation
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
extract.
The washer-extractor must be placed on a smooth
level surface so that the entire base of the machine is
supported and rests on the mounting surface.
The standard installation does not require anchoring
unless mandated by state or local codes.
Static and dynamic loads on the floor or foundation are
shown in Table 2.
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
Table 2 can be used as a reference when designing
floors and foundations.
IMPORTANT: Mounting bolts MUST be used for
installation on the 18, 25 and 35 models equipped
with steam heat and models installed on metal base
frames. Refer to Mounting Bolt Installation.
W488
Floor Load Data
Model
18
25
33
35
40
55
75
100
135
165
200
Kinetic Energy of the
Cylinder, (N/m)
1386
1730
2736
3240
4105
6640
12404
18361
23257
29581
29581
Dynamic Bottom
Load, (N/Hz)
700/16 750/16 1200/16 1200/16 1200/16 1700/15 2000/15 2960/13 3900/13 4960/13 6100/13
Table 2
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Mechanical Installation
Frame Dimensions and Mounting Bolt
Location
18, 25, 35, 55, 75, 100, 135 and 165 Pound
Capacity with U in the 8th position of the
Model Number (e.g. *X18PVXU6)
26 in.
(660 mm)
23.38 in.
(594 mm)
20.87 in.
(530 mm)
1.81 in.
(30 mm)
23.23 in.
(590 mm)
1.3 in.
(33 mm)
22.59 in.
(650 mm)
2.56 in.
(65 mm)
1.81 in.
(30 mm)
CFD42N
18 MODEL
CFD42N
Figure 14
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Installation
26 in.
(660 mm)
23.38 in.
(594 mm)
1.81 in.
(30 mm)
20.87 in.
(530 mm)
1.3 in.
(33 mm)
2.56 in.
(65 mm)
30.79 in.
(782 mm)
27.17 in.
(690 mm)
1.81 in.
(30 mm)
CFD44N
25 POUND
CFD44N
Figure 15
IMPORTANT: Drawing is not to scale.
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
1.34 in.
(34 mm)
28.86 in.
(733 mm)
26.18 in.
(665 mm)
.87 in.
(22 mm)
1.34 in.
(34 mm)
26.77 in.
(680 mm)
1.97 in.
(50 mm)
1.97 in.
(50 mm)
30.71 in.
(780 mm)
CFD541N
33 MODEL
CFD541N
Figure 16
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Installation
30.70 in.
(780 mm)
28 in.
(712 mm)
25.51 in.
(648 mm)
1.44 in.
(36.5 mm)
1.34 in.
(34 mm)
1.34 in.
(34 mm)
2.6 in.
66 mm)
2.6 in.
(66 mm)
33 in.
(838 mm)
30.12 in.
(765 mm)
1.44 in.
(36.5 mm)
CFD43N
35 MODEL
CFD43N
Figure 17
IMPORTANT: Drawing is not to scale.
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
1.34 in.
(34 mm)
328 in.
(833 mm)
30.12 in.
(765 mm)
.87 in.
(22 mm)
1.34 in.
(34 mm)
26.77 in.
(680 mm)
1.97 in.
(50 mm)
1.97 in.
(50 mm)
CFD542N
30.71 in.
(780 mm)
40 MODEL
CFD542N
Figure 18
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Installation
35.35 in.
(898 mm)
1.97 in.
(50 mm)
32.68 in.
(830 mm)
36.61 in.
(930 mm)
1.97 in.
(50 mm)
29.13 in.
(740 mm)
3.15 in.
(80 mm)
3.15 in.
(80 mm)
CFD45N
55 MODEL
CFD45N
Figure 19
IMPORTANT: Drawing is not to scale.
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
41.73 in.
(1060 mm)
2.36 in.
(60 mm)
37.8 in.
(960 mm)
42.52 in.
(1080 mm)
2.36 in.
(60 mm)
34.25 in.
(870 mm)
3.74 in.
(95 mm)
3.74 in.
(95 mm)
CFD46N
75 MODEL
CFD46N
Figure 20
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Installation
47.24 in.
(1200 mm)
1.57 in.
(40 mm)
39.76 in.
(1010 mm)
42.91 in.
(1090 mm)
1.57 in.
(40 mm)
40.94 in.
(1040 mm)
3.15 in.
(80 mm)
3.15 in.
(80 mm)
CFD48N
100 MODEL
CFD48N
Figure 21
IMPORTANT: Drawing is not to scale.
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
47.24 in.
(1200 mm)
1.67 in.
(42.5 mm)
46.65 in.
(1185 mm)
50 in.
(1270 mm)
1.67 in.
(42.5 mm)
40.94 in.
(1040 mm)
3.15 in.
(80 mm)
3.15 in.
(80 mm)
CFD47N
135 MODEL
CFD47N
Figure 22
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Installation
51.2 in.
(1300 mm)
1.3 in.
(33 mm)
46.7 in.
(1185 mm)
49.25 in.
(1251 mm)
1.3 in.
(33 mm)
44.9 in.
(1140 mm)
3.15 in.
(80 mm)
3.15 in.
(80 mm)
CFD47N
165 POUND
CFD47N
Figure 23
IMPORTANT: Drawing is not to scale.
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
44.8 in.
(1138 mm)
51.18 in.
(1300 mm)
1.73 in.
(44 mm)
1.73 in.
(44 mm)
44.8 in.
(1138 mm)
3.19 in.
(81 mm)
3.19 in.
(81 mm)
51.18 in.
(1300 mm)
CFD536N
200 POUND
CFD536N
Figure 24
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Installation
18, 25 and 35 Pound Capacity with A or M in
the 8th position of the Model Number (e.g.
*X18PVXA6)
26 in.
(660 mm)
2.17 in.
(55 mm)
22.05 in.
(560 mm)
26.38 in.
(670 mm)
2.17 in.
(55 mm)
19.13 in.
(486 mm)
3.43 in.
(87 mm)
3.43 in.
(87 mm)
CFD49N
18 MODEL
CFD49N
Figure 25
IMPORTANT: Drawing is not to scale.
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
26 in.
(660 mm)
2.17 in.
(55 mm)
25.98 in.
(660 mm)
30.31 in.
(770 mm)
2.17 in.
(55 mm)
19.13 in.
(486 mm)
3.43 in.
(87 mm)
3.43 in.
(87 mm)
CFD51N
25 MODEL
CFD51N
Figure 26
IMPORTANT: Drawing is not to scale.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Installation
30.8 in.
(782 mm)
1.77 in.
(45 mm)
30.31 in.
(770 mm)
33.85 in.
(860 mm)
1.77 in.
(45 mm)
25.16 in.
(639 mm)
2.78 in.
(71 mm)
2.78 in.
(71 mm)
CFD50N
35 MODEL
CFD50N
Figure 27
IMPORTANT: Drawing is not to scale.
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Mounting Bolt Installation
(If Required)
3. Put bolts through the machine in the anchors and
fasten them. (For the 18, 25, and 35 models, the
diameter of the bolt must be minimum 1/2-13 or
12 mm; for the 33, 40, 55, 75, 100, 135, 165 and
200 models, the diameter of the bolt must be
minimum 5/8-11 or 16 mm.)
1
2
4. To level machine, fill the spaces between the
machine base and floor with machinery grout.
Grout completely under all frame members.
Remove front and rear panels to gain access to all
frame members. Force grout under the machine
base until all voids are filled.
3
5. Remove the spacers carefully, allowing the
machine to settle into the wet grout.
6 in.
(152 mm)
6. Position washers and locknuts on machinery
anchor bolts and finger-tighten to machine base.
7. After the grout is completely dry, tighten the
locknuts by even increments – one after the
other – until all are tightened evenly and the
machine is fastened securely to the floor.
CFS485N
4
CFS485N
1
2
3
4
Base Frame
Bolt
Washer
Anchor Bolt/Plug
8. Remove the four red transport brackets which
secure the moving components of the machine
during shipping. Refer to Figures 29, 31 and 32
for typical transport bracket locations.
Figure 28
After the concrete has cured and the anchors are
installed, proceed as follows:
1. Place the washer-extractor adjacent to the
foundation. Do not attempt to move it by pushing
on the sides. Always insert a pry bar or other
device under the bottom of the frame of the
washer-extractor to move it.
2. Place the washer-extractor carefully over the
anchors.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Installation
Removing the Transport Brackets
To prevent damage during transportation, the machine
has been equipped with four red transport brackets
(refer to Figure 29 for 18, 25 and 35 models; refer to
Figure 30 for 33 and 40 models; refer to Figure 31 for
55 and 75 models [depending on model number]; refer
to Figure 32 for 100, 135, 165 and 200 models) to
eliminate every possible movement of the tub.
After the machine has been placed level, take off the
service panels and the back panel to remove these
transport brackets.
WARNING
1
The machine must never be activated
before removing these transport
brackets.
W489
CFD34N
CFD34N
18, 25 AND 35 MODELS WITH A OR M IN THE 8TH
POSITION IN THE MODEL NUMBER
(E. G. *X18PVXM6)
1
CFD65N
CFD65N
18, 25 AND 35 MODELS WITH U IN THE 8TH
POSITION IN THE MODEL NUMBER
(E. G. *X18PVXU6)
1
Transport Brackets
Figure 29
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
FRONT
FRONT
1
1
1
REAR
REAR
1
1
33 AND 40 MODELS
1
CFD543N
1
CFS488N
100, 135, 165 AND 200 MODELS
Transport Brackets
CFS488N
1
Figure 30
Transport Brackets
Figure 32
FRONT
1
REAR
CFS487N
55 AND 75 MODELS
CFS487N
1
Transport Brackets
Figure 31
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Installation
Drain Connection
A drain system of adequate capacity is essential to
washer-extractor performance.
Ideally, the water should empty through a vented pipe
directly into a sump or floor drain.
Figure 33 shows drain line and drain trough
configurations.
REAR OF MACHINE
A flexible connection must be made to a vented or air
gap drain system to prevent an air lock and to prevent
siphoning. If proper drain size is not available or
practical, a surge tank is required. A surge tank in
conjunction with a sump pump should be used when
gravity drainage is not possible, such as in belowground-level installations.
Before any deviation from specified installation
procedures is attempted, the customer or installer
should contact the distributor.
Increasing the drain hose length, installing elbows, or
causing bends will impair washer-extractor
performance.
1
2
Refer to Table 3 for capacity-specific drain
information.
Installation of additional washer-extractors will
require proportionately larger drain connections. Refer
to Table 4.
3
4
5
6
7
8
CFS490N
1
2
3
4
5
6
7
8
Water Inlet
Water Inlet Air Gap
Drain Pipe
1-Inch Minimum Waste Line Air Gap
(Per local code)
Steel Grate
Drain Trough
Strainer
Waste Line
Figure 33
44
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Drain Information
Model
18
25
33
35
40
55
75
100
135
165
200
3 in.
(76.2
mm)
3 in.
(76.2
mm)
3 in.
(76.2
mm)
3 in.
(76.2
mm)
3 in.
(76.2
mm)
3 in.
(76.2
mm)
1
1
1
1
2
2
21.13
32
21.13
32
Drain flow
32
capacity
gal/min gal/min gal/min gal/min gal/min
(160
(120
(160
(120
(120
l/min)
l/min)
l/min)
l/min)
l/min)
73
gal/min
(280
l/min)
73
gal/min
(280
l/min)
73
gal/min
(280
l/min)
73
gal/min
(280
l/min)
73
gal/min
(280
l/min)
73
gal/min
(280
l/min)
Recommended
drain pit
size
8.3 ft3
(235 l)
11 ft3
(304 l)
16 ft3
(455 l)
20 ft3
(575 l)
24 ft3
(679 l)
31.8 ft3
(9001)
Drain
2 in.
2 in.
2 in.
2 in.
2 in.
connection
(51 mm) (51 mm) (50 mm) (51 mm) (50 mm)
size, ID
Number of
drain
outlets
1
1
2.5 ft3
(72 l)
1
3.3 ft3
(95 l)
1
5.1 ft3
(1451)
1
5.8 ft3
(165 l)
6.4 ft3
(1811)
Table 3
Drain Line Sizing
Minimum Drain ID
Model
Number of Machines
1
2
3
4
5
6
7
18
2 in.
(51 mm)
3 in.
(76.2 mm)
3.5 in.
(88 mm)
4 in.
(102 mm)
4.5 in.
(114 mm)
5 in.
(124 mm)
5.5 in.
(140 mm)
25
2 in.
(51 mm)
3 in.
(76.2 mm)
3.5 in.
(88 mm)
4 in.
(102 mm)
4.5 in.
(114 mm)
5 in.
(124 mm)
5.5 in.
(140 mm)
33
2 in.
(51 mm)
3 in.
(76.2 mm)
3.5 in.
(88 mm)
4 in.
(102 mm)
4.5 in.
(114 mm)
5 in.
(124 mm)
5.5 in.
(140 mm)
35
2 in.
(51 mm)
3 in.
(76.2 mm)
3.5 in.
(88 mm)
4 in.
(102 mm)
4.5 in.
(114 mm)
5 in.
(124 mm)
5.5 in.
(140 mm)
40
2 in.
(51 mm)
3 in.
(76.2 mm)
3.5 in.
(88 mm)
4 in.
(102 mm)
4.5 in.
(114 mm)
5 in.
(124 mm)
5.5 in.
(140 mm)
55
3 in.
(76.2 mm)
4 in.
(102 mm)
5 in.
(131 mm)
6 in.
(152 mm)
6.7 in.
(170 mm)
7.3 in.
(186 mm)
8 in.
(203 mm)
75
3 in.
(76.2 mm)
4 in.
(102 mm)
5 in.
(131 mm)
6 in.
(152 mm)
6.7 in.
(170 mm)
7.3 in.
(186 mm)
8 in.
(203 mm)
100
3 in.
(76.2 mm)
4 in.
(102 mm)
6 in.
(152 mm)
7 in.
(177.8 mm)
8 in.
(203 mm)
10 in.
(254 mm)
12 in.
(305 mm)
135
3 in.
(76.2 mm)
4 in.
(102 mm)
6 in.
(152 mm)
7 in.
(177.8 mm)
8 in.
(203 mm)
10 in.
(203 mm)
12 in.
(305 mm)
165
3 in.
(76.2 mm)
4 in.
(102 mm)
6 in.
(152 mm)
7 in.
(177.8 mm)
8 in.
(203 mm)
10 in.
(203 mm)
12 in.
(305 mm)
200
3 in.
(76.2 mm)
4 in.
(102 mm)
6 in.
(152 mm)
7 in.
(177.8 mm)
8 in.
(203 mm)
10 in.
(203 mm)
12 in.
(305 mm)
Table 4
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Installation
Water Connection
To connect water service to machine with rubber
hoses, use the following procedure:
WARNING
1. Before installing hoses, flush the water system
for at least two minutes.
To avoid personal injury, recommended
inlet water temperature should be no
higher than 125° Fahrenheit (51° Celsius).
2. Check filters in the washer-extractor’s inlet hoses
for proper fit and cleanliness before connecting.
W709
3. Hang the hoses in a large loop, do not allow them
to kink.
The 18-135 models are delivered with hoses with
3/4 inch hose connectors. The 165 model is delivered
with 3 x 1 inch and 1 x 3/4 inch hose connectors.
These hoses fit the water inlet valves of the machine
and the main water inlet taps. To ensure the optimal
functioning of the water inlet valves, the water
pressure on the inlet should be between 30-85 psi
(2-5.7 bar). If the pressure is too low, the cycle time
will increase considerably. In case of boiler fed
machines, a maximum of hot water of 194°F (90°C)
should be available:
If additional hose length is needed use flexible hoses
with screen filters. Each hose should have a screen
filter installed to keep rust and other foreign particles
out of the water inlet valves.
Pressure of 30-85 psi (2-5.7 bar) provides best
performance. Although the washer-extractor will
function at lower pressures, increased fill times will
occur with some loss of supply flushing.
Suitable air cushions should be installed in supply
lines to prevent “hammering.”
Connections should be supplied by a hot and a cold
water line per national and local codes.
Water Supply Information
Model
Water inlet
connection
size
Number of
water inlets
(standard)
Recommended
pressure
Inlet flow
capacity
18
25
33
35
40
55
75
100
135
165
200
0.75 in. 0.75 in. 0.75 in. 0.75 in. 0.75 in. 0.75 in. 0.75 in. 0.75 in. 0.75 in. 1.0 in. 0.75 and
(19 mm) (19 mm) (19 mm) (19 mm) (19 mm) (19 mm) (19 mm) (19 mm) (19 mm) (25 mm) 1.0 in.
(19 and
25 mm)
3
3
3
3
3
3
3
4
4
4
4
30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi 30-85 psi
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
(2-5.7
bar)
bar)
bar)
bar)
bar)
bar)
bar)
bar)
bar)
bar)
bar)
5.3 gal/
min
(20 l/
min)
5.3 gal/
min
(20 l/
min)
5.3 gal/
min
(20 l/
min)
5.3 gal/
min
(20 l/
min)
5.3 gal/
min
(20 l/
min)
12 gal/
min
(45 l/
min)
12 gal/
min
(45 l/
min)
12 gal/
min
(45 l/
min)
12 gal/
min
(45 l/
min)
25 gal/
min
(95 l/
min)
25 gal/
min
(95 l/
min)
Table 5
46
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Electrical Installation
DANGER
WARNING
Hazardous Voltage. Can cause shock,
burn or cause death. Allow machine
power to remain off for two minutes prior
to working in and around AC inverter
drive.
Do not use a phase adder on any variablespeed machine.
W490
The washer-extractor should be connected to an
individual branch circuit not shared with lighting or
other equipment.
W359
WARNING
Hazardous Voltage. Can cause shock,
burn or death. Verify that a ground wire
from a proven earth ground is connected
to the lug near the input power block on
this machine.
W360
The AC inverter drive requires a clean power supply
free from voltage spikes and surges. A voltage monitor
should be used to check incoming power. The
customer’s local power company may provide such a
monitor.
If input voltage measures above 240V for a 220V
drive or above 480V for a 400V drive, ask the power
company to lower the voltage. As an alternative, a
step-down transformer kit is available from the
distributor.
The AC drive provides overload protection for the
drive motor. However, a separate single or three phase
circuit breaker must be installed for complete
electrical overload protection. This prevents damage
to the motor by disconnecting all legs if one should be
lost accidentally. Check the data plate on the back of
the washer-extractor or consult Table 6 for circuit
breaker requirements.
The connection should be shielded in a liquid tight or
approved flexible conduit with proper conductors of
correct size installed in accordance with the National
Electric Code or other applicable codes. The
connection must be made by a qualified electrician
using the wiring diagram provided with the washerextractor, or according to accepted European standards
for CE-approved equipment.
Use wire sizes indicated in Table 6 for runs up to
50 feet.
Use next larger size for runs of 50 to 100 feet. Use two
sizes larger for runs greater than 100 feet.
For personal safety and proper operation, the washerextractor must be grounded in accordance with state
and local codes. If such codes are not available,
grounding must conform with the National Electric
Code, article 250-95. The ground connection must be
made to a proven earth ground, not to conduit or water
pipes.
IMPORTANT: Alliance Laundry Systems
Warranty does not cover components that fail as a
result of improper input voltage.
IMPORTANT: Do NOT use fuses in place of a
circuit breaker.
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Installation
Electrical Specifications
25
33
35
40
55
75
100
135
48
3+PE
6
15
14/2.5
3+N+PE
Not available
3+PE
Not available
2/3+PE
10
15
14/2.5
3+PE
6
15
14/2.5
3+N+PE
Not available
3+PE
Not available
2/3+PE
10
15
14/2.5
3+PE
6
15
14/2.5
3+N+PE
18
20
12/4.0
3+PE
18
20
12/4.0
2/3+PE
18
20
12/4.0
3+PE
12
15
14/2.5
3+N+PE
Not available
3+PE
Not available
2/3+PE
12
15
14/2.5
3+PE
6
15
14/2.5
3+N+PE
18
20
12/4.0
3+PE
18
20
12/4.0
2/3+PE
18
20
12/4.0
3+PE
12
15
14/2.5
3+N+PE
Not available
3+PE
Not available
2/3+PE
16
20
14/2.5
3+PE
12
15
14/2.5
3+N+PE
12
15
14/2.5
3+PE
15
20
12/4.0
3+PE
17
20
12/4.0
3+N+PE
17
20
12/4.0
3+PE
18
25
10/6.0
3+PE
17
25
10/6.0
3+N+PE
17
25
10/6.0
3+PE
20
30
10/6.0
Table 6 (continued)
20
17
28
21
18
29
32
44
63
41
36
58
32
44
63
41
36
58
41
36
58
62
55
88
62
55
88
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
20
30
Not available
25
20
30
Not available
40
50
70
Not available
50
40
60
Not available
40
50
70
Not available
50
40
60
Not available
50
40
60
70
60
90
70
60
90
AWG
/mm2
Circuit
Breaker
3
3
3
1/3
3
3
3
1/3
3
3
3
1/3
3
3
3
1/3
3
3
3
1/3
3
3
3
1/3
3
3
3
3
3
3
3
3
3
Full Load
Amps
(Heating
Element
kW)
Phase
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60
Electric Heat
AWG
/mm2
Cycle
440-480
380-415
200-240
200-240
440-480
380-415
200-240
200-240
440-480
380-415
200-240
200-240
440-480
380-415
200-240
200-240
440-480
380-415
200-240
200-240
440-480
380-415
200-240
200-240
440-480
380-415
200-240
440-480
380-415
200-240
440-480
380-415
200-240
Circuit
Breaker
Voltage
N
P
Q
X
N
P
Q
X
N
P
Q
X
N
P
Q
X
N
P
Q
X
N
P
Q
X
N
P
Q
N
P
Q
N
P
Q
Full
Load
Amps
Code
18
Standard
Wire
Model
Voltage Designation
10/6.0
12/4.0
10/6.0
10/6.0
12/4.0
10/6.0
8/10.0
8/10.0
4/25.0
8/10.0
8/10.0
6/16.0
8/10.0
8/10.0
4/25.0
8/10.0
8/10.0
6/16.0
8/10.0
8/10.0
6/16.0
4/25.0
6/16.0
3/35.0
4/25.0
6/16.0
3/35.0
9001000
Installation
Table 6 (continued)
Electrical Specifications
Full
Load
Amps
Circuit
Breaker
AWG
/mm2
50/60
3
3+PE
20
25
10/6.0
P
380-415
50/60
3
3+N+PE
20
25
10/6.0
Q
200-240
50/60
3
3+PE
32
40
8/10.0
N
440-480
50/60
3
3+PE
19
25
10/6.0
P
380-415
50/60
3
3+N+PE
18
25
10/6.0
Q
200-240
50/60
3
3+PE
27
40
8/10.0
AWG
/mm2
Wire
440-480
Circuit
Breaker
Phase
N
Full Load
Amps
(Heating
Element
kW)
Cycle
200
Electric Heat
Voltage
165
Standard
Code
Model
Voltage Designation
41 (9x3 kW)
52 (9x4 kW)
50 (9x3 kW)
61 (9x4 kW)
76 (9x3 kW)
42 (9x3 kW)
53 (9x4 kW)
51 (9x3 kW)
62 (9x4 kW)
77 (9x3 kW)
63
63
63
80
100
63
63
63
80
100
8/10.0
8/10.0
8/10.0
6/16.0
4/25.0
8/10.0
8/10.0
8/10.0
6/16.0
4/25.0
Table 6
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Installation
Electrical Connection
Remove the cover plate at the back of the machine.
Using copper conductors only, connect the power
cable to the connectors. Refer to the instructions listed
on the machine’s decal on how to connect the
machine.
After electrical installation is complete, run the
machine through a test cycle and check for clockwise
basket rotation during the extract step. If rotation is not
clockwise, disconnect the power from the machine and
have a qualified electrician reverse any 2 motor leads
at the AC drive terminal block.
Remote Liquid Supply Connection
CONNECTION OF THE LIQUID SUPPLY HOSES
CFS492N
Chemical Injection Supply System
Figure 34
WARNING
Dangerous Chemicals. May damage eyes
and skin. Wear eye and hand protection
when handling chemicals; always avoid
direct contact with raw chemicals. Read
the manufacturer’s directions for
accidental contact before handling
chemicals. Ensure an eye-rinse facility
and an emergency shower are within easy
reach. Check at regular intervals for
chemical leaks.
A connection has been placed at the back of the
machine. There are nine holes in this connection, through
each of which a liquid supply hose can be connected.
CAUTION
Drill out plugs and nipples before making
supply hose connection. Failure to do so
can cause buildup of pressure and risk a
tubing rupture.
W491
W363
Undiluted chemical dripping can damage the machine.
Therefore, all chemical supply dispenser pumps
should be mounted below the washer’s injection point.
All dispenser tubing should also run below the
injection point. Loops do not prevent drips if these
instructions are not followed. Failure to follow these
instructions could damage the machine and void the
warranty.
50
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Steam Requirements
(Steam Heat Option Only)
For washer-extractors equipped with optional steam
heat, install piping in accordance with approved
commercial steam practices. Steam requirements are
shown in Table 7.
WARNING
Never touch internal or external steam
pipes, connections, or components. These
surfaces can be extremely hot and will
cause severe burns. The steam must be
turned off and the pipe, connections, and
components allowed to cool before the
pipe can be touched.
SW014
Steam Supply Information
Steam inlet connection, in (mm)
Number of steam inlets
Recommended pressure, psi (bar)
Maximum pressure, psi (bar)
18-75
100/135
165/200
3/8 (10)
1/2 (13)
3/4 (19)
1
1
1
30 – 80 (2.0 – 5.5)
30 – 80 (2.0 – 5.5)
30 – 80 (2.0 – 5.5)
80 (5.5)
80 (5.5)
80 (5.5)
Table 7
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Installation
Supply Programming Table
When programming a supply step on the WE-8,
choose between 9 different supply steps. Refer to
Table 8.
Supply 1
Turns on the water valve in compartment A of
the supply box.
Supply 2
Turns on the water valve in compartment B of
the supply box.
Supply 3
Turns on the water valve in compartment C of
the supply box.
Supply 4
Activates supply relay 1.
Supply 5
Activates supply relay 2.
Supply 6
Activates supply relay 3.
Supply 7
Activates supply relay 4.
Supply 8
Activates supply relay 5.
Supply 9
Activates supply relay 6.
Primary 220 Volt Remote Liquid Supply
Connection
IMPORTANT: When programming a supply step,
supplies 1, 2 and 3 DO NOT control the relays
shown on Figure 36. Programming supply 1, 2 or 3
ONLY activates water in compartment A, B or C.
Programming supply 4 activates relay 1.
Programming supply 5 on the WE-8 will activate
supply relay 2, etc. Programming supply 4-9 on the
WE-8 will activate supply relay 1-6 on the board,
respectively. Refer to Table 8.
Supply
Supply Supply Supply Supply Supply Relay
Relay Relay Relay Relay Relay
1
1
2
2
3
3
4
5
4
6
7
6
5
8
9
10
11 12
13* 14**
Table 8
NOTE: The Supply button is button 6.
Pump
Pump
Pump
Pump
Pump
Pump
1
2
3
4
5
6
Supply Relay Configuration (No Wiring)
ELECTRICAL CONNECTION OF THE
CFS8N
LIQUID SUPPLY PUMPS
Supply
Supply Supply Supply Supply Supply Relay
Relay Relay Relay Relay Relay
1
1
2
2
3
3
4
5
4
6
7
5
8
9
10
CFS8N
* L1 (220 VAC) wire or terminal for remote liquid supply
connection.
** L2 common wire (220 VAC) or terminal for remote
liquid supply connection.
Figure 36
6
11 12
13* 14**
TYPICAL SUPPLY RELAY BOARD CONFIGURATION
CFS7N
CFS7N
* L1 (220 VAC) wire or terminal for remote liquid supply
connection.
** L2 common wire (220 VAC) or terminal for remote
liquid supply connection.
Figure 35
The supply relay board is set up to give NO Voltage
AC output to the respective terminals. It is a dry
contact closure of the relay. The voltage applied must
be supplied with the jumper configurations. Refer to
Figure 36.
52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Supply relay 1 controls terminals 1 and 2. Figure 36
shows the jumper wire from terminal 13 (L1 220 VAC)
to all other even pins (i.e., 2, 4, 6…). This applies L1
(220 VAC) to terminal 2. When supply 4 on the WE-8
is programmed, this will close supply relay 1 and
apply L1 (220 VAC) through pin 2 to pin 1. This signal
is used from the terminal to the chemical supply
vendors first pump.
IMPORTANT: Supply 4 must be programmed on
the WE-8 to create the signal on terminal 1. The
chemical vendor will always use terminal 14 as the
common terminal for all pumps. This will apply for
the remainder of the 220 VAC circuit for each of
the pump signals. For the remainder of the relays,
supply relay 2 will control terminals 3 and 4;
supply relay 3 will control terminals 5 and 6; etc.
IMPORTANT: The WE-8 must be programmed
for supply 4-9 to energize the supply relays 1-6
respectively.
Primary 220 Volt Remote Liquid Supply
Connection (Continued)
EXAMPLE: PUMPS 24V ~
CFSD518N
CFD518N
Figure 37
The 220V can be transformed to other values to drive
other type supply pumps.
EXAMPLE: 5 PUMPS 220V ~ AND 1 PUMP
24V ~
CFS495N
CFS495N
Figure 38
Also, pumps with different operating voltage
requirements can be combined.
WITH AN EXTERNAL 24V DC
CFS496N
CFS496N
Figure 39
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Installation
Out-of-Balance Switch
Automatic Lubricator
Only for 75-200 Models
1
2
1
2
CFS501N
1
2
Window
Probe
Figure 40
The out-of-balance switch is mounted on the upper
right side on the back of the control panel. There is a
window around the probe of the switch that is mounted
on the movable part of the machine.
When the machine goes out of balance by overloading
or uneven distribution of the linen, the out-of-balance
switch will interrupt this action to prevent damage to
the machine.
IMPORTANT: To guarantee good functioning, the
probe should be centered horizontally and
vertically at 1/3 from the bottom of the tilt window
(when machine drum is empty).
CFS502N
1
2
Lubricating Device
Screw
Figure 41
The bearing house of the machine is equipped with a
lubricating device (1) which automatically lubricates
the bearing during one year. Upon delivery of the
machine, this lubricator has been brought into use.
When replacing, please put on the matching screw (2)
in the foreseen opening of the lubricator to activate.
Refer to the machine’s Parts Manual for lubricating
device parts in formation.
WARNING
Ignoring this instruction will inevitably
cause damage to the bearings and void
the warranty!
W492
54
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001000
Installation
Control Function Test
b. Close the door without locking it and attempt
to start the washer. The washer should not
start with the door unlocked.
The washer-extractor should be cleaned after the
installation is complete. A function test should then be
executed on the unloaded machine:
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
1. Verify that power supply voltage and phase are
correct in accordance with the washer-extractor’s
requirements.
2. Open manual shut-off valves to the washerextractor.
If the door lock and interlock are not functioning
properly, call a service technician.
7. For standard processing, select Cycle 01 by
pressing key 0 and key 1 on the keypad. Then
press the Start key (or run factory test cycle 39 by
pressing key 3, key 9 and Start key).
3. Press the Emergency Stop button.
4. Apply power to the washer-extractor.
Run a complete cycle, checking operation of
water inlet valves, drain, and extract functions.
5. Release the Emergency Stop button.
6. Check the door interlock before starting
operation:
8. Cylinder rotation must be clockwise in an extract
step for all models. If rotation is not correct,
disconnect power. A qualified electrician must
reverse any two leads between the AC drive and
the main drive motor. Refer to Figure 42.
a. Attempt to start the washer with the door
open. The washer-extractor should not start
with the door open.
2
3
1
(L1) (L2) (L3)
4
MACHINE
5
CFD10N
CFD10N
1
2
3
Power Supply
Typical Connection (See machine schematic or
invertor drive for details of electronic
connections)
AC Drive Connections
4
5
Motor Leads (Swap any 2 of the 3 motor leads
to change rotation direction)
Main Drive Motor
Figure 42
9001000
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55