LTR20081000, Rev. B
1/28/08
Read This First!
Water Quality Maintenance
Important Safety Instructions . . . . . . . . . . . . . . 1
Cal Spas Clear Water Plan . . . . . . . . . . . . . . . . 20
Basic Spa Information . . . . . . . . . . . . . . . . . . . . 1
Alternative Sanitation Options . . . . . . . . . . . . 20
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . 20
Preparing for Your New Portable Spa
Planning the Best Location . . . . . . . . . . . . . . . . 3
Chemical Safety . . . . . . . . . . . . . . . . . . . . . . . . 21
Preparing a Good Foundation . . . . . . . . . . . . . . 3
Chemical Descriptions . . . . . . . . . . . . . . . . . . . 22
120 Volt Electrical Installation . . . . . . . . . . . . . . 4
Traditional Chemical Start Up . . . . . . . . . . . . . 24
240 Volt Electrical Installation . . . . . . . . . . . . . . 4
Bromine Clear Water Plan . . . . . . . . . . . . . . . . 24
GFCI Wiring Diagram . . . . . . . . . . . . . . . . . . . . . 6
Chlorine Clear Water Plan . . . . . . . . . . . . . . . . 25
Gas Heater Hook up . . . . . . . . . . . . . . . . . . . . . . 7
Ozonator Clear Water Plan . . . . . . . . . . . . . . . . 25
Filling and Powering Up Your Portable Spa . . . 9
Bromine Generator Clear Water Plan . . . . . . . 26
Maintenance Schedule . . . . . . . . . . . . . . . . . . . 27
Operating Your Spa
5100, 6200 and 6300 Electronic Control
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning and Maintenance
Removing and Reseating the Pillows . . . . . . . 28
9800 Electronic Control Operation . . . . . . . . . 13
Spa Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Auxiliary Control Operation . . . . . . . . . . . . . . . 17
Draining Your Portable Spa . . . . . . . . . . . . . . . 29
Wireless Spa Monitor . . . . . . . . . . . . . . . . . . . . 17
Winterizing (Cold Climate Draining) . . . . . . . . 29
Adjustable Jets . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning the Cover, Shell and Pillows . . . . . . 30
Diverter Knobs . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning and Replacing the Filter . . . . . . . . . . 31
Air Venturis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adjustable Therapy System™ . . . . . . . . . . . . . 19
Multi-Colored Spa Light Operation . . . . . . . . . 19
Aromatherapy . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Waterfalls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Entertainment System
Operating the CD Player . . . . . . . . . . . . . . . . . . 32
Raising and Lowering the 20” TV . . . . . . . . . . 32
Playing a Movie . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the iPod Docking Station . . . . . . . . . . . 33
Using the Universal Remote Control . . . . . . . 33
Programming the Universal Remote Control . 34
Appendix
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . 35
Keeping Fit with your Spa . . . . . . . . . . . . . . . . 43
Cal Spas™ Chemicals . . . . . . . . . . . . . . . . . . . 45
2008 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONTACT INFORMATION
For customer service, please contact your
authorized dealer immediately. If you need
additional information and/or assistance,
contact:
LMS Customer Service Department
1462 East Ninth Street
Pomona, CA 91766.
Toll Free: 1-800-CAL-SPAS
Fax: 1-909-629-3890
Copyright 2007-2008 Lloyds Material Supply, Inc. All rights reserved. Duplication
without written consent is strictly prohibited.
Cal Spas®, Adjustable Therapy System™, ATS™, Bio-Clean™, Cal Zone Quest
2000™, Cal Premium™, Cal Select™, Cal Stone™ Ultimate Fitness Spa Series™, and
XL Heat Exchanger™ are registered trademarks.
Due to continuous improvement programs, all models, operation, and/or specifications
are subject to change without prior notice.
LTR20081000, Rev. B
1/28/08
Read This First!
Read This First!
Important Safety Instructions
When installing and using this electrical equipment,
always follow basic safety precautions. Following these
instructions will help make your first spa session a
pleasurable one.
READ AND FOLLOW ALL INSTRUCTIONS
NOTE: A licensed electrician may be required to upgrade
your standard receptacle and/or circuit breaker.
DANGER -- RISK OF ACCIDENTAL DROWNING:
Do not allow children to be in or around a spa unless
a responsible adult supervises them. Keep the spa
cover on and locked when not in use. See instructions
enclosed with your cover for locking procedures.
DANGER -- RISK OF INJURY: The suction fittings
in this spa are sized to match the specific water flow
created by the pump. Should the need arise to replace
the suction fittings, or the pump, be sure the flow rates
are compatible.
DANGER -- RISK OF INJURY: Never operate the
spa if the suction fitting or filter baskets are broken or
missing.
DANGER -- RISK OF INJURY: Never replace a suction
fitting with one that is rated less than the flow rate marked
on the original suction fitting.
High water temperatures have a high potential for
causing fetal damage during pregnancy. Women who
are pregnant, or who think they are pregnant, should
always check with their physician prior to spa usage.
The use of alcohol, drugs or medication before or
during spa use may lead to unconsciousness, with the
possibility of drowning.
Persons suffering from obesity, a medical history of heart
disease, low or high blood pressure, circulatory system
problems or diabetes should consult a physician before
using the spa.
Persons using medications should consult a physician
before using the spa since some medications may
induce drowsiness while others may affect heart rate,
blood pressure and circulation.
Hyperthermia Danger
Prolonged exposure to hot air or water can induce
hyperthermia. Hyperthermia occurs when the internal
temperature of the body reaches a level 3˚F to 6˚F
above the normal body temperature of 98.6˚F (or 2˚C to
4˚C above 37˚C). While hyperthermia has many health
benefits, it is important not to allow your body’s core
temperature to rise above 103˚F (39.5˚C). Symptoms
of excessive hyperthermia include dizziness, lethargy,
drowsiness and fainting. The effects of excessive
hyperthermia may include:
•
Failure to perceive heat
•
Failure to recognize the need to exit spa or hot tub
DANGER -- RISK OF ELECTRIC SHOCK: Install the
spa at least 5 feet (1.5 meters) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet
of metal surfaces if each metal surface is permanently
bonded by a minimum #8 AWG solid copper conductor
to the outside of the spa’s control box.
•
Unawareness of impending hazard
•
Fetal damage in pregnant women
•
Physical inability to exit the spa
•
Unconsciousness
DANGER -- RISK OF ELECTRIC SHOCK: Do not
permit any external electrical appliances, such as lights,
telephones, radios, televisions, and etc., within five feet
(1.5 meters) of the spa. Never attempt to operate any
electrical device from inside the spa. This does not
apply to lights, stereos and televisions that are built into
the spa as factory options from Cal Spas™.
WARNING: The use of alcohol, drugs, or medication
can greatly increase the risk of fatal hyperthermia.
WARNING -- RISK OF INJURY
The spa water should never exceed 104˚F (40˚C). Water
temperatures between 100˚F (38˚C) and 104˚F (40˚C)
are considered safe for a healthy adult. Lower water
temperatures are recommended for young children and
when spa use exceeds 10 minutes.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Basic Spa Information
The following operating and maintenance instructions
are very important and must be followed carefully. With
the proper care and maintenance, your spa will provide
you with years of satisfaction and performance.
Do not be afraid to push buttons or turn knobs to learn
about your new spa, as it is built with quality materials
and excellent craftsmanship.
Your new spa has been engineered with a high-powered
water pump that pushes water through various therapy
Page Read This First!
jets, which will relax even the tightest muscles. In addition
to the water pressure, you can add air into the spa water
with air venturi handles located seat-side that increase
the intensity of your massage.
The filtering of this spa is very important. It will minimize
cleaning time and the amount of chemicals needed
to keep your spa water balanced. The two daily preprogrammed filter cycles of two hours in duration can be
increased to six hour cycles if the need arises. This can
be accomplished through the topside control panel.
IMPORTANT: Keep the spa covered when not in use!
•
Covered spas use less electricity while maintaining
a set temperature.
•
Covering your spa will protect your spa’s finish from
the sun’s ultraviolet rays.
•
You are required to keep the spa covered to maintain
warranty coverage.
•
Covering your spa helps prevent children from
drowning in the spa.
Your new spa comes equipped with an electric heater.
Following the directions listed below will ensure the most
efficient operation:
NOTE: This method is only for spa usage under two
hours a week.
•
•
Keep the spa’s operating temperature 5˚F below the
desired usage temperature when not in use. One
or two hours before use, set the temperature to the
desired temperature.
•
The air venturis should be used sparingly. When
open, water temperature drops quite rapidly and can
also dissipate chemicals.
Allowing the water temperature to lower more than 10˚F
below the desired usage temperature and reheating it
prior to usage will cause the heater to operate longer than
it normally would maintaining the desired temperature.
Doing this will increase your operating cost and makes
your heater work more than necessary.
The filter needs to be cleaned or changed on a regular
basis. This process takes only a few minutes and
the result is increased water clarity and equipment
longevity.
Water level is very important to the operation of your
spa. If the water level is too low or too high, your spa will
not operate properly. The water level should be to the
middle of the skimmer area when the spa is not being
used.
We recommend that your spa water be changed every
4 to 6 months. You may find the need to change your
spa water more frequently with heavy use. When empty,
your spa should be cleaned with a non-abrasive cleaner,
such as Cal Spas™ All Surface Cleaner, and then rinsed
thoroughly.
See the section “Cleaning and Maintaining Your Spa” for
instructions on draining your spa.
When filling your spa, always fill through the skimmer
filter canister. Use only regular tap water.
WARNING: DO NOT USE SOFT WATER.
If the spa usage exceeds two hours a week, the set
temperature should remain at the desired usage
temperature.
Page 2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Preparing for Your New Portable Spa
Preparing for Your New Portable Spa
Most cities and counties require permits for exterior construction and electrical circuits. In addition, some
communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to
prevent unsupervised access to the property by children. Your dealer can provide information on which permits may
be required and how to obtain them prior to the delivery of your spa.
Planning the Best Location
where the bathers can clean their feet before entering
your spa.
Here are some of the things that you will need to consider
when determining where to place your new spa.
Allow for Service Access
Safety First
Do not place your spa within 10 feet (3 m) of overhead
power lines.
Consider How You Will Use Your Spa
How you intend to use your spa will help you determine
where you should position it. For example, will you use
your spa for recreational or therapeutic purposes? If
your spa is mainly used for family recreation, be sure to
leave plenty of room around it for activity. If you will use
it for relaxation and therapy, you will probably want to
create a specific mood around it.
Plan for Your Environment
If you live in a region where it snows in the winter or
rains frequently, place the spa near a house entry. By
doing this, you will have a place to change clothes and
not be uncomfortable.
Consider Your Privacy
In a cold-weather climate, bare trees won’t provide
much privacy. Think of your spa’s surroundings during
all seasons to determine your best privacy options.
Consider the view of your neighbors as well when you
plan the location of your spa.
Provide a View with Your Spa
Think about the direction you will be facing when sitting
in your spa. Do you have a special landscaped area in
your yard that you find enjoyable? Perhaps there is an
area that catches a soothing breeze during the day or a
lovely sunset in the evening.
Keep Your Spa Clean
In planning your spa’s location, consider a location
where the path to and from the house can be kept clean
and free of debris.
Many people choose to install a decorative structure
around their spa. If you are installing your spa with any
type of structure on the outside, such as a gazebo,
remember to allow access for service. It is always best
to design special installations so that the spa can still be
moved, or lifted off the ground.
Preparing a Good Foundation
Your spa needs a solid and level foundation. The area
that it sits on must be able to support the weight of the
spa and the occupants who use it. If the foundation
is inadequate, it may shift or settle after the spa is in
place, causing stress that could damage your spa shell
or finish.
Damage caused by inadequate or improper foundation
support is not covered by the warranty. It is the
responsibility of the spa owner to provide a proper
foundation for the spa. We strongly recommended that
you have a qualified, licensed contractor prepare the
foundation for your spa.
Place the spa on a level foundation (preferably a 4”
concrete slab). If you are installing the spa indoors, pay
close attention to the flooring beneath it. Choose flooring
that will not be damaged or stained.
If you are installing your spa on an elevated wood deck
or other structure, consult a structural engineer or a
contractor to ensure the structure will support the weight
of 150 pounds per square foot.
Your Cal Spas™ retailer can help you with your foundation
and more. Your retailer has a wealth of information and
experience about how to get the most out of your spa
and can provide you with a full line of accessories that
are designed to complement your spa and increase your
enjoyment.
Prevent dirt and contaminants from being tracked into
your spa by placing a foot mat at the spa’s entrance
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page Preparing for Your New Portable Spa
120 Volt Electrical Installation
240 Volt Electrical Installation
Always follow applicable local, state and federal codes
and guidelines.
All 240V spas must be permanently connected
(hardwired) to the power supply. These instructions
describe the only acceptable electrical wiring procedure.
Spas wired in any other way will void your warranty and
may result in serious injury.
Use only a dedicated electrical line with a 20 amp
breaker.
Cord-and-plug connections may not use a cord longer
than 15 feet (4.6 m) and must be plugged into a dedicated
20 amp GFCI connection (NEC 680.42(A)(2)). Do not
use extension cords!
Always use a weatherproof-covered receptacle.
Receptacle shall be located not less than 5 feet (1.5 m)
from and not exceeding 10 feet (3.0 m) from the inside
wall of the spa. (NEC 680.43(A))
Do not bury the power cord. If your cord becomes
damaged, replace it before next usage.
All 120V spas must have a GFCI. This can be either a 20
amp GFCI receptacle or a 20 amp GFCI cord and plug
kit as shown (CKIT110 - P/N ELE09700086).
Test the GFCI plug prior to first use and periodically when
the spa is powered. To test the GFCI plug version, follow
these instructions. (Spa should already be plugged in
and operational.)
Press the TEST button on the GFCI. The GFCI will trip
and the spa will stop operating.
Press the RESET button on the GFCI. The GFCI will
reset and the spa will turn back on.
The spa is now safe to use.
If the GFCI trips while the spa is in use, press the RESET
button. If the GFCI does not reset, unplug the spa and
call your local Cal Spas dealer for service. DO NOT USE
THE SPA!
Page This is the only acceptable electrical wiring procedure.
Spas wired in any other way will void your warranty. See
the wiring diagram on page 6.
When installed in the United States, the electrical wiring
of this spa must meet the requirements of National
Electric Code, ANSI/NFPA 70-2008 and any applicable
local, state, and federal codes. The electrical circuit must
be installed by an electrical contractor and approved by
a local building / electrical inspector.
GFCI and Wiring Requirements
The power supplied to the spa must be on a dedicated
GFCI protected circuit as required by ANSI/NFPA 70
with no other appliances or lights sharing the power.
Use copper wire with THHN insulation. Do not use
aluminum wire.
Use the table on the next page to determine your GFCI
and wiring requirements.
When NEC requires the use of wires larger than #6
AWG, install a junction box near the spa and use #6
AWG wire between the junction box and the spa.
Wire runs over 85 feet must increase wire gauge to the
next lower number. For example: A normal 50 amp GFCI
with four #8 AWG Copper wires run over 85 feet would
require you to go to four #6 AWG copper wires.
Read and follow the heater manufacturer’s safety and
installation instructions prior to installation and operation.
Incorrect installation may damage the heater and void
its warranty.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Preparing for Your New Portable Spa
Spa Model
All 240V spas (except 6300 control boxes requiring
high amperage - see below)
GFCI Required
Wires Required
One 50 amp GFCI
Four #8 AWG copper wires
Spas with the 6300 control box (when high amperage One 60 amp GFCI
is selected on circuit board)
Four #8 AWG copper wires
SEE CONFIGURATION INSTRUCTIONS BELOW.
Ultimate Fitness spas with one 5.5 kW heater
One 50 amp GFCI
Four #8 AWG copper wires
Ultimate Fitness spas with two 5.5 kW heaters
Service 1: One 50
amp GFCI
Service 1: Four #8 AWG copper
wires
Service 2: One 30
amp GFCI
Service 2: Three #8 AWG copper
wires
Testing the GFCI Breaker
Configuring the 6300 Control System
Test the GFCI breaker prior to first use and periodically
when the spa is powered. To test the GFCI breaker
follow these instructions (spa should be operating):
The 6300 control system requires higher power than
other 240V systems. Dip switch #10 is factory set in the
ON position. This causes the heater to shut off when
any pump is running in high speed. To allow the heater
to continue operating, dip switch #10 must be set to the
OFF position.
Press the TEST button on the GFCI. The GFCI will trip
and the spa will shut off.
Reset the GFCI breaker by switching the breaker to the
full OFF position, wait a moment, then turn the breaker
back on. The spa should have power again.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
To ensure your spa functions properly, ensure the
following steps are performed before starting your spa:
•
When installing the electrical system, use a 60 amp
GFCI. Follow the GFCI wiring diagram on the next
page.
•
Have your dealer or installer set dip switch #10 to the
OFF position on the circuit board as shown below.
Page Preparing for Your New Portable Spa
GFCI Wiring Diagram
Page 2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Preparing for Your New Portable Spa
Gas Heater Hook up
Ultimate Fitness Series spa owners may buy and install a separate gas heater and pump for use with their spa. This
option may be purchased separately from your local distributor.
Spa owners are responsible for ensuring installation of their gas heater conforms to local, state, and federal
regulations. The electrical and gas installation must be performed by contractors and approved by a local building /
electrical inspector. Failure to do so may void your warranty.
All Ultimate Fitness Series spas are plumbed with a gas heater ready union located inside the cabinet at either the
front or rear, depending on the model. (See the figures below and at right.) Properly installed, they can be attached
to an external gas heater. Customers are responsible for creating openings in the panel to accommodate the lines
and wiring. The gas heater should be located not less than 10 feet and no more than 25 feet away from the spa.
To connect the plumbing for an external gas heater:
1. Disconnect the ready union.
2. Cut off both sides of the union and discard it.
3. Create two 2½” diameter holes through the spa panel.
4. Use two 2” couplings to connect the hoses to 10’ - 15’ 2-3/8” diameter PVC lines.
5. Connect PVC lines to the gas heater.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page Preparing for Your New Portable Spa
Page 2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Preparing for Your New Portable Spa
Filling and Powering Up Your Portable Spa
Never fill your spa with soft water. Soft water makes it
impossible to maintain the proper water chemistry and
may cause the water to foam, which will ultimately harm
the finish of the spa and void your warranty.
7. Once the water is at the correct level and air is bled,
turn on the power at the GFCI breaker. (Ensure that
the 120V spas are connected to the proper electrical
outlet.)
1. Once the spa has been placed on an approved
surface and has been correctly wired by a licensed
electrician, inspect all plumbing connections in the
equipment area of your spa. Ensure that these
connections are secure and that they did not loosen
during shipment.
Note: Depending on the model, when the power
is turned on to the spa, the controls will perform a
diagnostic check for approximately five minutes. When
the diagnostic is complete, the spa will automatically
operate at filter speed and continue heating until the spa
water temperature reaches the default temperature of
100˚F.
2. If equipped, open all gate valves in the equipment
area. Before operating the spa, these valves must
be in the up or “open” position.
3. Remove the filter basket and cartridge from skimmer/
filter canister.
4. Place a garden hose in the skimmer/filter canister
and fill your spa with regular tap water to the proper
water level (halfway up the skimmer area).
5. (For owners of the automatic bromine generator)
Make sure the dial on the face of the bromine
generator unit is turned to the OFF position.
6. Open the air relief valve (located next to the two
filters, if equipped) after the air bubbles stop coming
out of it. Close the valve hand-tight.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
8. If no water is flowing when the pump is running
there could be an air pocket at the suction side of
the pump. Shut off power to the spa and loosen the
pump union on the suction side of the pump to bleed
the air. When air is bled, turn power back on.
9. Re-install the filter and the filter basket into the
skimmer/filter canister.
The spa is now ready for use.
NOTE: Never run the spa with the gate valves closed
or without water circulating for long periods of time. Be
careful not to over-tighten the plumbing fittings.
Page Operating Your Spa
Operating Your Spa
5100, 6200 and 6300
Electronic Control
Operation
Initial Start up
When first powered up, it will automatically
revert to Priming mode. A Pr on the
topside display will indicate this. Priming
mode will be active for less than five
minutes at which time the heater will be
activated and the water temperature will
be maintained in Standard mode. The
spa will heat to 100°F (37.5°C) at start up
until the set temperature is changed as
described below.
Temperature Adjustment
(Range 80°F to 104°F, 26°C to 40°C)
The 6200 and 6300 electronic control panels display
the actual water temperature in degrees Fahrenheit.
The displayed temperature will only be current after the
pump has been running for at least two minutes.
•
Ec will display solid if temperature is not current
and will alternate with spa temperature if measured
temperature is current.
•
Economy mode will heat the water to the set
temperature while Sleep mode, indicated by a SL
on the main display, will also only activate the heater
during the filtering cycles but will only heat the
water to within 20°F (10°C) of the set temperature.
Like Economy mode, SL will display solid when
temperature is not current and will alternate with
actual temperature when it is current.
To display the temperature that the spa is set to:
•
Press the Temp button. The temperature setting will
flash.
•
While the display is flashing, each time you press
Temp button, the set temperature will change up or
down one degree.
•
If the desired temperature is opposite of the direction
each press of the button is making, release button,
allow display to stop flashing and then press Temp
button to change temperature the other direction.
Standard, Economy and Sleep Heating
Modes
Your new spa is equipped with a heating feature that
gives you complete control of the heating system.
When the spa is powered up, it will automatically start in
standard heating mode.
•
St will light briefly on the main display. In this mode,
the heating system will automatically maintain the
set spa temperature. In the economy-heating mode,
the heating system will only activate during filtration
times.
Page 10
NOTE: Displayed temperature will only be current after
the pump has been running for at least two minutes.
Switching Modes
•
Press Temp button followed by the Light button.
•
Press the same sequence to switch to the next
mode.
Jets
Press the Jets button:
•
Once to activate low speed pump.
•
Twice to activate high speed.
•
Three times to turn pump off.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Operating Your Spa
Light
•
Low speed pump
After 4 hours
Press the Light button to turn on the light. Press it once
again to turn the light off. All optional lighting such as
the control panel light and cabinet perimeter lighting is
controlled by the Light button and will turn on and off
with the spa light.
•
High speed pumps
After 15 minutes
•
Optional circulation pump
After 15 minutes
•
Optional turbo
After 15 minutes
•
Spa light
After 15 minutes
Option
Press the Option button to turn on the pump 2. Press it
once again to turn off the pump 2 (6200 Controls only).
6300 Controls - Pump 2 and Pump 3
Sequence
•
Press Option button once to activate high speed
pump 2.
•
Press Option button twice to activate high speed
pump 3 and high speed pump 2
•
Press 3 times to activate pump 3 hi speed only
•
Press 4 times to turn pumps off
Automatic Time outs
These features will automatically turn themselves off
during periods of continuous use:
Setting Filtration Cycles
Your spa is programmed to filter twice a day. The first
cycle will begin 6 minutes after the spa is turned on and the
second cycle 12 hours later. The factory has programmed
the cycle to last for 2 hours but this can be switched to
4, 6, or 8 hours depending on your requirements. To
set filtration time, turn off the power to the spa at the
time of day you would like one of the filtration cycles to
begin then turn back on after 30 seconds. When power
has been restored, press the Temp button then the Jets
button. Press Temp button again to change the filtering
cycle duration. When desired duration is selected press
the Jets button to exit.
At the beginning of each filtering cycle the Turbo system
will run for approximately 30 seconds. The low speed
pump will run for the duration of the filtering cycle and if
an Ozone system is installed it will be activated. During
filtering, FC will appear on the main display.
Diagnostic Messages
Message
Meaning
--
Spa temperature is unknown. After pump has been running for 2 minutes temperature will be
displayed.
HH
Overheat protection (spa is shutdown) DO NOT ENTER THE WATER! One sensor has detected
118˚F (48˚C) at the heater. Remove the spa cover and allow spa to cool below 107˚F (42˚C).
Press any button on the topside display to reset spa. If spa will not reset after spa has cooled,
turn off power for approximately 30 seconds and then turn power back on. If display message is
repeated then shut the power off to the spa and call your dealer or service organization.
OH
Overheat protection (spa is shutdown) DO NOT ENTER THE WATER! If the spa has reached
110˚F (43˚C), remove the spa cover to cool the water. At 107˚F (42˚C), the spa should reset
itself. If the spa does not reset, then shut the power off to the spa, wait 30 seconds and restore
power to spa. If display message is repeated then shut the power off to the spa and call your
dealer or service organization.
IC
A possible ice condition exists within the spa. No action is required, the pump will automatically
activate.
SA or Sb
Spa is shut down. Spa has detected that one of the sensors is not operating properly. One
of these may display briefly during overheat then disappear when overheat situation has been
resolved. Call your dealer or service organization if message does not go away.
Sn
Sensor (Spa is shut down). The high limit or water temperature sensors are not working correctly.
Call your dealer or service organization.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 11
Operating Your Spa
HL
A difference in readings between temperature sensors has been detected indicating a possible
water flow problem. Make sure spa is filled to proper level and that pumps are primed (water
is flowing). Also check to make sure filter cartridges are clean. If message does not reset, call
your dealer or service organization.
LF
This will display on the 5th occurrence of the HL message in 24 hours indicating a persistent flow
problem. The heater will be shut down but other functions will continue to operate. Follow HL
message actions then press any button to reset.
dr
Insufficient water flow through the heater has been detected. Spa will be shut down for 15
minutes. Check water level and fill spa if water level is low. Make sure pumps are primed (water
is flowing) and filter cartridges are clean. Press any button to reset or wait 15 minutes and spa
will automatically reset. If message does not reset, call your dealer or service organization.
dY
Insufficient water level detected in heater. This will display on the 3rd occurrence of dr message.
Follow directions for dr message and press any button to reset spa. Spa will not automatically
reset when dY is displayed.
Sf
Safety Suction System (spa is shut down). The display will show Sf as soon as the vacuum
switch closes. All functions will turn off and the system will be disabled until a panel button is
pressed.
ST
Indicates heater is in standard mode.
Ec
Indicates heater is in economy mode.
SL
Indicates heater is in sleep mode.
Page 12
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Operating Your Spa
9800 Electronic Control Operation
When first powered up, the 9800 electronic
system will perform a self-diagnostic check
and then it will automatically heat to and
maintain a temperature of 100°F (37.5°C)
until you change the set temperature as
listed in the “Temperature Adjustment”
section below.
These instructions will describe features and
options that your particular spa may not be
equipped with.
Initial Start-up
When your spa is first powered up, it displays some
configuration codes and then goes into priming mode
(Pr will appear on the display panel). This mode lasts up
to four minutes and then the spa begins to heat to its pre
-programmed temperature of 100°F.
Standard Mode: This is programmed to maintain the
desired temperature. Note that the last measured spa
temperature displayed is current only when the pump
has been running for at least two minutes. The “STAND”
icon will display until the mode is changed.
Temperature Adjustment
Economy Mode: Economy mode heats the spa to the
set temperature only during filter cycles. The “ECON”
icon will display until the mode is changed. Pressing the
“JETS 1” button while in economy mode puts the spa in
standard-in-economy mode, which operates the same
as standard mode but reverts back to economy mode
automatically after one hour. During this time, pressing
the “MODE/PROG” button will revert to economy mode
immediately.
(Range 80°F to 104°F, 26°C to 40°C)
The start-up temperature is set at 100°F (37.5°C). The
last measured temperature is constantly displayed
on the control panel. Note that the last measured spa
temperature is displayed. The displayed temperature
will be updated when the pump has been running for at
least two minutes.
Press the “UP” or “DOWN” buttons once to display the
set temperature. Each time either button is pressed
again, the set temperature will increase or decrease
depending on which button is pressed. After three
seconds, the control panel will automatically display the
last measured spa temperature.
Time
When time hasn’t been programmed, the “TIME” icon
flashes. To set the time, press the “TIME” button and
then the “MODE/PROG” button. Use the “UP” and
“DOWN” buttons to adjust time. See the next page for
more detailed instructions.
Standard, Economy, Sleep, and Standby
Modes
Mode/Prog: This button is used to switch between
standard, economy, and sleep modes.
1. Press “MODE/PROG” to enter mode programming.
Sleep Mode: Sleep mode heats the spa to within 20°F
(11°C) of the set temperature only during filter cycles. The
“SLEEP” icon will display until the mode is changed.
Standby Mode: Pressing “Warm” or “Cool” then “JETS
2” will turn off all spa functions temporarily. This is helpful
when changing a filter. Pressing any button resets the
spa.
Jets 1
Press the “JETS 1” button once to turn pump 1 on or off
and to shift between low and high speeds if equipped.
If left running, the low speed turns off after two hours
and the high speed turns off after 15 minutes. On noncirculation systems, the low speed of pump 1 runs when
the blower or any other pump is on. It may also activate
for at least two minutes every 30 minutes to detect the
spa temperature and then to heat to the set temperature if
needed, depending upon the mode. When the low speed
turns on automatically, it cannot be deactivated from the
panel; however, the high speed may be started.
2. Press the “DOWN” button to cycle through to the
desired mode.
3. Press “MODE/PROG” to confirm selection.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 13
Operating Your Spa
Jets 2
Preset Filter Cycles
Press the “JETS 2” button once to turn pump 2 on or off
and to shift between low and high speeds if it is a twospeed pump. If left running, the pump will turn off after
15 minutes.
There are two filter cycles per day. The start and end
times of each cycle are programmable. To program, set
the time as instructed above, then press “MODE/PROG”
to advance to the next setting (or to exit after the last
setting). The default filter cycles are as follows:
Option
•
The first filter cycle is automatically activated at 8:00
AM and operates the pump until 10:00 AM. The
“FILTER 1” indicator icon will light when filter 1 is
running.
•
The second filter cycle is automatically activated at
8:00 PM and operates the pump until 10:00 PM. The
“FILTER 2” indicator icon will light when filter 2 is
running.
This is an optional feature. Press the “OPTION” button
to turn the optional equipment on and off. If left on, the
equipment will automatically turn off after 15 minutes.
Light
Press the “LIGHT” button to turn the spa light on and
off and to shift between dim and bright settings if your
light is dimmable. On dim, the control panel will show the
center circle plus one quarter of the light beams. Half of
the light beams will show on medium brightness, and all
of the light beams will show on bright.
Invert
Press the “INVERT” button to change the numbers in the
display to read upside down. Another press returns the
display to the right-side-up position. This enables you to
read the display while you are in the spa.
The pump and the ozone generator will run during
filtration. At the start of each filter cycle, the blower will
run on highest speed for 30 seconds to clean out the
air channels. The lowest speed of pump 2 and pump
3 will run for five minutes. In the event of power loss or
shut down, the time of day will need to be reset for filter
cycles to run according to your desired programming.
Clean up Cycle
To lock the panel:
When the pump or blower is turned on by a button press,
a clean-up cycle begins 30 minutes after the pump or
blower is turned off or times out. The pump and the
ozone generator will run for one hour.
•
Ozone
Locking the Panel
Press “TIME”, “JETS 1”, and the “UP” button within
three seconds. When locked, the panel will display
“LOCK”. All buttons are frozen except the “TIME”
button.
To unlock the panel:
•
Press “TIME”, “JETS 1” then the “DOWN” button
within three seconds.
Setting the Temperature Lock
To activate the temperature lock:
•
Press the “UP” or “DOWN” button, “TIME”, “JETS 1”,
then the “UP” button within three seconds. The panel
will display “TEMP LOCK” when the set temperature
is locked.
To unlock the set temperature:
•
Press the “UP” or “DOWN” button, “TIME”, “JETS
1”, and then the “DOWN” button.
Circulation Pump
This is an optional feature. The circulation pump will
come on when the system is checking temperature,
during filter cycles, during freeze conditions, or when
another pump is on.
Page 14
This is an optional feature. On most systems, the ozone
generator (if installed) runs during filter cycles (except
when pump 1 is operating at high speed on a non-circ
ulating system) and during clean-up cycles. On some
systems, the ozone generator operates whenever the
pump runs. If your system is configured with the optional
ozone disable feature, the ozone generator will turn off
for one hour any time a function button (“JETS 1”, “JETS
2”, “OPTION” etc.) is pressed.
Freeze Protection
If the temperature sensors detect a drop to 44°F within
the heater, the pump automatically activates to provide
freeze protection. The equipment stays on until four
minutes after the sensors detect that the spa temperature
has risen to 45°F or higher. In colder climates, an optional
additional freeze sensor may be added to protect against
freeze conditions that may not be sensed by the standard
sensors. Auxiliary freeze sensor protection acts similarly
except with the temperature thresholds determined by
the switch and without a four-minute delay in turnoff.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Operating Your Spa
Periodic Reminder Messages
Press the “Mode” button to reset a displayed reminder.
Message
Frequency
Action Required
rPH
Every 7 days
Test and adjust chemical levels per manufacturer’s instructions.
rSA
Every 7 days
Test and adjust chemical levels per manufacturer’s instructions.
rCL
Every 30 days
Remove, clean, and reinstall filter per manufacturer’s instructions.
rtg
Every 30 days
Test and reset GFCI per manufacturer’s instructions. Drain and refill spa
per manufacturer’s instructions.
rdr
Every 90 days
Drain and refill spa per manufacturer’s instructions.
rCO
Every 180 days
Clean and condition spa cover.
rCH
Every 365 days
Install New Bio-Clean™ Filter.
Diagnostic Messages
Message
Meaning
Action Required
No message on display. Power has The control panel will be disabled until power returns. Spa
been cut off to the spa.
settings and time of day will be preserved for 30 days with a
battery back-up.
OHH
“Overheat” - The spa has shut DO NOT ENTER THE WATER. Remove the spa cover and
down. One of the sensors has allow water to cool. Once the heater has cooled, reset by
detected 118°F at the heater.
pushing any button. If spa does not reset, shut off the power
to the spa and call your dealer or service organization.
OHS
“Overheat” - The spa has shut
down. One of the sensors has
detected that the spa water is
110°F.
ICE
“Ice” - Potential freeze condition No action required. The pumps and the blower will automatically
detected.
activate regardless of spa status.
Sna
Spa is shut down. The sensor that If the problem persists, contact your dealer or service
is plugged into the Sensor “A” jack organization. (May appear temporarily in an overheat situation
is not working.
and disappear when the heater cools.)
Snb
Spa is shut down. The sensor that If the problem persists, contact your dealer or service
is plugged into the Sensor “B” jack organization. (May appear temporarily in an overheat situation
is not working.
and disappear when the heater cools.)
Sns
Sensors are out of balance. If this is If the problem persists, contact your dealer or service
alternating with the temperature, it organization.
may just be a temporary condition.
If the display shows only this
message (periodically blinking),
the spa is shut down.
HFL
A substantial difference between If the water level is okay, make sure the pumps have been
the temperature sensors was primed. If problem persists, contact your dealer or service
detected. This could indicate a flow organization.
problem.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
DO NOT ENTER THE WATER. Remove the spa cover and
allow water to cool. At 107°F, the spa should automatically
reset. If spa does not reset, shut off the power to the spa and
call your dealer or service organization.
Page 15
Operating Your Spa
Message
Meaning
LF
Persistent low flow problems. Follow action required for HFL message. Heating capacity of
(Displays on the fifth occurrence of the spa will not reset automatically; you may press any button
the HFL message within 24 hours.) to reset.
Heater is shut down, but other spa
functions continue to run normally.
dr
Inadequate
heater.
dry
Inadequate
water
detected Follow action required for dr message. Spa will not
in heater. (Displays on third automatically reset; you may press any button to reset.
occurrence of dr message.) Spa is
shut down.
Pr
When your spa is first actuated, it The priming mode will last for up to four minutes and then the
will go into priming mode.
spa will begin to heat and maintain the water temperature in
the Standard mode.
--F or --C
Temperature unknown
------
Economy
or
Sleep
mode. In Economy or Sleep mode, the pump may be off for hours
Temperature not displayed.
outside a filter cycle. If you wish to see the current spa
temperature, either switch to Standard mode or turn Jets1 on
for at least two minutes.
BUF
Internal problem detected.
Stby
Pressing a button combination Press any button to leave Standby Mode and return to normal
on the user panel has activated operation.
Standby Mode.
SF
Safety Suction.
ST
Indicates heater is in Standard None.
Mode.
Ec
Indicates heater is in Economy None.
Mode.
SL
Indicates heater is in Sleep Mode.
Page 16
Action Required
water
detected
in Check water level in spa. Refill if necessary. If the water level
is okay, make sure the pumps have been primed. Press any
button to reset.
After the pump has been running for two minutes, the
temperature will be displayed.
Repair required. Contact your dealer or service organization.
Spa is shut down. The display will show SF when a vacuum
switch closes. All functions will turn off and the system will be
disabled until a panel button is pressed.
None.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Operating Your Spa
Auxiliary Control Operation
The auxiliary control option is available with the 9800 controls only. It is a small panel with four buttons that control
certain spa functions, such as primary or additional jets, TV, or lights. It conveniently puts the control of several spa
functions at your fingertips without having to get up.
For operation, see the previous section, “9800 Electric Control Operation”.
Auxiliary Panel Configuration
Functions
Standard configuration
JETS 1, JETS 2, LIGHT, OPTION
Spa models with automatic TV
JETS 1, JETS 2, TV, OPTION
Spa models with 3-pump system
JETS 1, JETS 2, JETS 3, OPTION
Wireless Spa Monitor
The wireless spa monitor allows you to monitor and change your spa’s activity from a distance. The table below
describes each button’s function.
Light
Operates spa light and LED mood lighting
Temp
Display or adjust the set temperature control
Jet 1
Turn on or off jet 1
Mode
Switch between Standard, Economy, and Sleep Modes
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 17
Operating Your Spa
Adjustable Jets
Diverter Knobs
Almost all of the jets in your spa are adjustable.
Rotating the face of an adjustable jet to the left (counterclockwise) will decrease the amount of water flow
through the jet. Rotating the face of an adjustable jet to
the right (clockwise) will increase the amount of water
flow through the jet. (See example shown below.)
Diverter knobs are 1” and 2” knobs located around the
top of your spa. They allow you to divert water through
jets from one side of the spa to the other, or in most
cases from floor jets to wall jets. This is accomplished by
rotating the diverter
knob to the left
(counterclockwise),
decreasing
the
amount of water
flow through a
section of jets.
To increase the
amount of water
flow through the
other section of jets,
rotate the handle to
the right (clockwise).
Neck jets adjust in the opposite directions (counterclockwise to increase, clockwise to decrease).
Air Venturis
Air venturis are the 1” knobs located around the top of
your spa. Each one will let you add a mixture of air with
the jet pressure. This is accomplished by rotating the
air venturi knob to the
left (counterclockwise) to
increase the amount of
airflow through the jets.
To decrease the amount
of airflow through the
jets, rotate the handle to
the right (clockwise).
Page 18
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Operating Your Spa
Adjustable Therapy System™
Pump On/Off
This button allows
the user to turn on
and off the ATS™
seat pump. Press
this button once to
turn the pump on.
Once on, the green
LED light on the
control panel will
illuminate, indicating
that the system is
operational. To turn
off the pump, press the “PUMP ON/OFF” button a second
time. Note: The pump must be on prior to operating any
other features of this system.
Pulse Mode
This button allows the user to turn the ATS™ massage
control on and off. Press the pulse button once to turn
on the massage control. Once pressed, the orange LED
in position number 1will light, indicating the number one
pulse mode. Each press of either the up or down button
will move the orange LED up or down to the next pulse
mode.
Note: Allow one second between each button press.
Pressing the button quickly may cause improper
operation. To turn the pulse mode off and return to
normal pump operation, press the “PULSE MODE”
button a second time.
Up
This button allows the user to cycle up from one through
seven massage modes one at a time. Each mode
offers a different pulsating massage. Some modes are
faster than others, so just cycle through them to find the
massage you like best.
Down
blink for one minute then shut off automatically. After the
second 15-minute session, the system will run through
a cool down cycle for up to two hours. In this cool down
mode, the user will only be able to operate the pump (by
again pressing the “PUMP ON/OFF” button). However,
the massage mode will remain off until the cool down
mode is completed.
Pulse Mode System
Pulse mode system will shut off for two hours unless
reset by the following procedure. During this time the
pump will run at a maximum speed.
•
In the off position, press the “PULSE MODE” button
once.
•
The green power light will flash to indicate reset.
Multi-Colored Spa Light
Operation
1. Turn the spa light on by pressing the “LIGHT” button
on the topside control panel.
2. To filter through the different color choices, press the
button on and off. Each time you press the button,
you advance to the next color.
3. To turn the spa light off when not in use, press the
“LIGHT” button.
Aromatherapy
This optional accessory is very easy to use. Unscrew
the cap on the aromatherapy chamber and drop in a bag
of scented aromatherapy beads and replace the cap.
Waterfalls
Some spa series include optional waterfalls. When the
booster pump is on, turn the knob near the waterfall,
or rotate the dial on top of the waterfall. Water will
immediately start flowing through it.
This button allows the user to cycle down through all
seven massage modes, one at a time.
Time Reset Mode
Pulse mode will normally run for 15 minutes then
automatically shut off. For another 15-minute session,
press the “PUMP ON/OFF” button and the “PULSE
MODE” button. A green LED will blink and the pump
will run on high-speed mode as part of a 15-minute cool
down period. After that, the pump will stop automatically
and the green LED light on the panel will continue to
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 19
Water Quality Maintenance
Water Quality Maintenance
Cal Spas Clear Water Plan
Great spa water is easily achieved when the right
chemicals and / or systems are used and the Cal Spas
Clear Water Plan is implemented. The key to clean,
clear, and safe water is to fully understand how spa water
reacts to users, system operation and chemical use. The
Clear Water Plan will help give you that understanding.
The first thing to understand about taking care of your
spa water is that preventive actions are much easier to
do than correcting water quality issues. For this reason,
we offer the Clear Water Plan as a simple, easy to follow
guide to clean, safe spa water.
Follow the Right Plan
You will need to decide which chemical plan or alternative
sanitation option works best for your spa water. Consult
your Cal Spas dealer for the right decision with regards
to your lifestyle and spa usage. Whichever plan you
decide on, follow it completely and don’t take shortcuts.
These plans will provide you with clean, safe, clear spa
water with a minimum of effort.
Before You Begin
Before you begin a Clear Water Plan, you should
understand that chemicals or systems alone will not take
care of your spa water. Other factors such as Filtration
and Bather Load also play an important part.
Filtration
The filter is the part of your spa that removes the debris
from the water. Even though Cal Spas uses the advanced
Bio Clean filter cartridge that protects itself from bacterial
growth, the filter still needs to be cleaned on a regular
basis to maximize your spa’s filtering performance and
heating efficiency.
In addition to spraying off the filter weekly to remove
surface debris, your filter should be deep cleaned
periodically to dissolve scale and other contaminants
that get lodged deep within the filter fibers and impede
the filtration process. Even if the filter looks clean, the
contaminants can clog the fibers and prevent water from
flowing through the filter resulting in the most common
spa problem—no heat, caused by a dirty filter.
Filter Cleaning
•
Traditional Chemical Options
Choose from either Bromine tablets or Chlorinating
granules as your sanitizer of choice. Both work well when
the appropriate Clear Water Plan is followed. Make sure
you follow all instructions and use only Cal Spas brand
chemicals.
Alternative Sanitation Options
Cal Zone Quest 2000 / 3000 Ozonator
This system automatically generates ozone gas and
injects it into the spa water. Ozone gas is far superior
to chemical bromine or chlorine in sanitizing spa water.
Saves replacement chemical cost and guards against
forgetting to add chemicals.
Cal Clarity Automatic Bromine Generator
This system automatically generates and releases
free bromine into the spa water. No more need to add
chemical bromine tablets or chlorine granules. Saves
replacement chemical cost and circumvents the need to
add chemicals on a regular basis.
Page 20
Place the dirty filter into a bucket of water deep
enough to cover the filter. Add 8 oz of Cal Spas
“Liquid Filter Cleaner” to the bucket of water.
Note: It is a good idea to keep a spare filter to be deep
cleaned while the regular filter is in the spa. This way,
you can rotate the filters and both will last longer.
•
Soak the filter for a minimum of 24 hours.
•
Remove the filter and spray clean with a water hose.
Spray each pleat carefully.
•
Allow filter to dry completely (a minimum of 2 days
drying time is recommended).
•
Reinstall filter as described in the Clear Water Plan.
Filtration Cycles
The filtration cycle of your spa is the process that allows
the water to flow through the filter. Your spa will filter
automatically twice each day. The factory set default time
for filtration is usually enough for normal use, however
heavy bather load or frequent use may require longer
filtration times or more frequent filtration cycles to keep
the spa water clean. Consult your Owner’s Manual for
setting your spa’s filtration times.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Water Quality Maintenance
Bather Load
“Bather Load” is the term used to describe the number of
people using a spa, combined with the length of usage,
and the frequency of usage. All these factors have a
great effect on the spa water. The higher the bather
load, the more chemicals need to be added and a longer
filtration time will be needed.
All versions of the Cal Spas Clear Water Plan are
designed for spas with average bather load. (3-4 people,
15 minutes of usage, 3 times a week at 100 degrees)
If your bather load exceeds these guidelines, and you
experience water quality problems, increase the amount
of filtration first, (go to the next higher filtration number)
then if water quality is still not adequate, consult the
advice of your Cal Spas dealer for additional chemical
or system recommendations. Be sure to give them your
bather load information.
Chemical Overview
The following information is intended for use with Cal
Spas chemicals only. Other brands of chemicals may
have similar names and/or usage descriptions but due
to manufacturing differences, use of other chemicals
can increase the likelihood of under- or over-dosing the
spa chemicals. Damage to the spa or spa’s components
from improper chemicals or chemical usage is not
covered under the spa’s warranty.
Chemical Safety
Failure to follow chemical directions may result in serious
injury, sickness, or even death.
Read and follow all printed instructions listed on bottles,
packages and in your owner’s manual.
Do not exceed chemical dosages as recommended
in the Clear Water Plan, or on chemical bottles and
packages. (Most chemical instructions are figured for a
500 gallon spa however, most spas hold less than 500
gallons, consult your owner’s manual for the approximate
gallons of your spa)
Never mix chemicals together.
Never change chemical brands or types without
completely draining, flushing and thoroughly cleaning
the spa and cover first.
Always protect your eyes while introducing chemicals
into the spa. Wear protective eyeglasses to prevent
powdered chemicals from blowing into the eyes or liquid
chemicals from splashing into the eyes.
In the event of overdosing a sanitizing chemical (chorine
or bromine), immediately turn off the power to the spa
and drain water to a safe and approved area. Refill with
fresh water and proceed with the Clear Water Plan start
up.
Physical Chemical Hazards
Do not allow chemicals to come in contact with skin,
eyes or clothing.
Always wear rubber gloves, protective eye wear and
clothing to reduce the risk of chemical contact and
irritation.
Remove and wash clothing that may have been exposed
to chemical contact prior to wearing them again.
Inhaling or ingesting chemicals will cause serious injury,
sickness, or even death.
Do not mix chemicals. Mixing chemicals together can
cause dangerous chemical reactions including the
release of toxic gas, fire and explosions.
Chemical Storage
Chemicals must be stored completely out of the reach
of children in an area that is well vented, cool, and dry.
Failure to provide a proper area for chemical storage
may result in serious injury, sickness, fire explosion
and even death. Do not store your chemicals inside the
equipment area of your spa.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 21
Water Quality Maintenance
Chemical Descriptions
The following descriptions and recommendations are intended for use with Cal Spas chemicals only. Many of these
chemicals will be used with alternative sanitation systems as well.
For use with any Clear Water Plan
Oxidizer Shock
Destroys
ammonia, organic
contaminants, and
odor causing wastes
in spa water.
Ph / Alkalinity Up
Raises pH and alkalinity
levels in spa water.
Iron Out
Helps prevent metals in
water from staining spa.
Use during start up.
Stain and Scale Defense
Helps prevent minerals
from
damaging
spa
components.
Ph / Alkalinity Down
Lowers pH and alkalinity
levels in spa water.
Liquid Hardness
Increaser
Helps reduce foaming and
corrosion by increasing
hardness levels in spa
water.
Spa Brite
Helps to quickly clear up cloudy spa water.
Filter Cartridge Cleaner
Deep cleans filter cartridge. Dissolves scale
and removes imbedded organic contaminants
from filter cartridge fibers.
Page 22
Foam Gone
Quickly breaks up existing foam on spa water.
Enzyme Formula
Biodegrades body oils, suntan lotions, and
organic contaminants in spa water. Do not use
on same day as adding Chlorine Granules.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Water Quality Maintenance
For use with the chlorine Clear Water Plan
Chlorinating Granules
Quick acting sanitizer / disinfectant for spa
water.
Test Strips – Chlorine
Provides accurate spa water testing for
bromine, pH, and total Alkalinity.
For use with the bromine Clear Water Plan
Test Strips -- Bromine
Provides
accurate
spa water testing for
bromine, pH, and total
alkalinity.
Go Brom
Establishes a bromide
reserve in spa water.
Use during start up.
Brominating
Tablets
Long lasting sanitizer
/ disinfectant for spa
water. Add to bromine
floater.
For use with the Cal Clarity Bromine Generator
Test Strips -- Sodium Bromide
Provides accurate spa water testing for sodium bromide.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 23
Water Quality Maintenance
Traditional Chemical Start Up
Bromine Clear Water Plan
Prior to filling a spa for the first time, or after a routine
draining, you will want to follow this start-up plan to
extend water life and performance. If you are following
either the Bromine or Chlorine Clear Water Plans, you
will notice that both start-up processes are the same with
the exception of Step 7. As with all chemical dosages
listed in these Clear Water Plans, start-up dosages are
intended for 500-gallon spas. Please adjust the chemical
dosages to the capacity of your particular spa.
This plan and its chemical dosages are intended for Cal
Spas chemicals only. Most chemical manufacturers use
different chemical formulas and strengths. Only Cal spas
chemicals are specially formulated to provide chemical
balance at lower dosages. Always read and follow printed
instructions on chemical bottles and packages.
Start Up
2. Based on the test strip readings:
Day One (Monday)
1. Test spa water using “Bromine Test Strips”.
1. Clean surface of spa with Cal Spas “Multi-Purpose
Cleaner”.
•
Adjust total alkalinity first (acceptable range of
80-120 ppm).
2. Apply a protective coat of Cal Spas “Fast Sheen” to
the acrylic surface.
•
Adjust the pH if needed (range is between 7.2
to 7.8).
3. Fill spa to proper water level with normal tap water.
(Do not use soft water.)
•
Add Cal Spas “Bromine Tablets” if needed (do
not add more than 2).
4. Use test strip and balance the spa water.
•
The recommended level of bromine is 3-5 ppm.
•
•
Adjust total alkalinity (acceptable range is 80120ppm).
Adjust pH if necessary (between 7.2 to 7.8).
3. Add 2 oz of “Stain and Scale Defense”.
4. Remove dirty filter from the spa and rinse off. Allow
to dry.
5. Pour in 16 oz of Cal Spas “Metal Protector” in the
center of the spa.
5. Place your extra clean filter cartridge back into the
spa.
6. Add either bromine or chlorine (according to your
preferred plan).
6. Vacuum debris from the bottom of your spa with the
spa vacuum.
Bromine: Add 2 oz of Cal Spas “Go Brom” to
establish a bromine base.
Day Two (Wednesday)
1. Test spa water using bromine test strips.
Add 2 Cal Spas “Bromine Tablets” to
bromine floater.
2. Based on the test strip reading, adjust total alkalinity,
then the pH if needed.
Set floater opening at #2.
Chlorine: Add two tablespoons of Cal Spas
“Chorine Granules” to the spa water.
7. Sprinkle 2 oz of Cal Spas “Oxidizer Shock” in the
center of the spa and turn on jets for 15 minutes.
Leave spa uncovered during this time.
8. Put cover on spa and allow to heat up to desired
temperature.
Day Three (Friday)
1. Test spa water using bromine test strips.
2. Based on the test strip reading:
•
Adjust total alkalinity, then the pH if needed.
•
Add one bromine tablet (if needed).
3. Add 2 oz of Cal Spas “Oxidizer Shock” to spa. Run
spa for 15 minutes with cover off.
4. Replace cover.
Page 24
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Water Quality Maintenance
Chlorine Clear Water Plan
5. Place your extra clean filter cartridge back into the
spa.
This plan and its chemical dosages are intended for Cal
Spas chemicals only. Most chemical manufacturers use
different chemical formulas and strengths. Only Cal Spas
chemicals are specially formulated to provide chemical
balance at lower dosages. Always read and follow printed
instructions on chemical bottles and packages.
6. Vacuum debris from the bottom of your spa with the
spa vacuum.
Day One (Monday)
1. Test spa water using chlorine test strips.
2. Based on the test strip readings:
•
Adjust total alkalinity (acceptable range of 80120 ppm).
•
Adjust the pH if needed (range is between 7.2
to 7.8).
•
Add 2 tablespoons of chlorine granules.
•
The recommended level of chlorine is 3-5 ppm.
3. Add 2 oz of “Stain and Scale Defense”.
Day Two (Wednesday)
1. Test spa water using chlorine test strips.
2. Based on the test strip reading, adjust total alkalinity,
then the pH if needed.
Day Three (Friday)
1. Test spa water using chlorine test strips.
2. Based on the test strip reading:
•
Adjust total alkalinity, then the pH if needed.
•
Add 2 tablespoons of chlorine granules (if
needed).
3. Add 2 oz of Cal Spas “Oxidizer Shock” to spa. Run
spa for 15 minutes with cover off.
4. Replace cover.
4. Remove dirty filter from the spa and rinse off.
Ozonator Clear Water Plan
This plan and its chemical dosages are intended for spas equipped with the optional
Cal Zone Quest 2000 / 3000 Ozonator or Del Zone Eclipse Ozonator. The chemical
references are designed for Cal Spas chemicals only.
Start Up
1. Follow the spa start up procedures for chlorine Clear Water Plan.
2. Set the spa’s filtration time for “F-4”. This activates the ozonator and produces
the ozone gas. (Follow the instructions in the owner’s manual.)
Note: Filtration time may need to be increased with heavy bather load.
Day One (Monday)
1. Test spa water using chlorine test strips. (You will need to use a small amount
of chlorine as a supplemental sanitizer)
2. Based on the test strip readings:
•
Adjust total alkalinity (acceptable range of 80-120 ppm).
•
Adjust the pH if needed (range is between 7.2 to 7.8).
•
Add 1 tablespoon of chlorine granules.
•
The recommended level of Chlorine is 1-3 ppm.
3. Add 2 oz of “Stain and Scale Defense”.
4. Remove dirty filter from the spa and rinse off.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 25
Water Quality Maintenance
5. Place your extra clean filter cartridge back into the
spa.
6. Vacuum debris from the bottom of your spa with the
spa vacuum.
Day Two (Friday)
1. Test spa water using chlorine test strips.
•
Adjust total alkalinity, then the pH if needed.
•
Add 1 tablespoon of chlorine granules (if
needed).
3. Add 2 oz of Cal Spas “Oxidizer Shock” to spa. Run
spa for 15 minutes with cover off.
4. Replace cover.
2. Based on the test strip reading:
Bromine Generator Clear Water Plan
This plan and its chemical dosages are intended for spas equipped with the optional Cal Clarity Automatic Bromine
Generator. The chemical references are designed for Cal Spas chemicals only. Note: Following these instructions
is very important to ensure proper operation of your Cal Clarity Automatic Bromine Generator.
Start Up
1. Clean surface of spa with Cal Spas “MultiPurpose Cleaner”.
2. Apply a protective coat of Cal Spas “Fast
Sheen” to the acrylic surface.
3. Fill spa to proper water level with normal
tap water. (Do not use soft water.)
4. Use bromine test strip and balance the spa
water:
•
Adjust total alkalinity (acceptable range
is 80 to 120 ppm),
•
Adjust pH if necessary (between 7.2 to
7.8).
5. Pour in 16 oz of Cal Spas “Metal Protector”
in the center of spa.
6. Test for TDS (total dissolved solids).
•
The ideal range is 50 to 300 ppm.
•
TDS must be less than 500 ppm to start with.
7. Phosphate level should be below 200 ppb. Remove phosphates if necessary.
8. Determine the gallon capacity of the spa. Be accurate, because this determines the amount of TRU BLU that
will be added. Consult the Cal Spas Pre-delivery Guide for spa gallons.
9. Power up the spa and make sure all the spa’s pumps are set to high speed. Turn the dial on the face of the Cal
Clarity Bromine Generator to OFF.
10. Sprinkle evenly over the surface of the spa one 2lb bottle of TRU BLU sodium bromide per 100 US gallons (370
liters) of water. Do not add too much!
Note: Each bottle of TRU BLU will raise TDS / conductivity amount approximately 500 ppm.
11. Allow spa to run for 15 minutes so the TRU BLU can dissolve completely before proceeding to the next step.
Page 26
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Water Quality Maintenance
12. Use sodium bromide test strips (not bromine) and
adjust sodium bromide level to 7.4 to 8.2 (equates
to 1700 to 2500 ppm TDS level).
13. Add 2 oz of Cal Spas “Oxidizer Shock” to help burn
out impurities in fill water.
14. Turn the dial on the bromine generator clockwise
until the LED display reads 10.
15. This will initiate the build up of a bromine bank.
16. Set the filtration cycle to “continuous” (F-C) for the
first 24 hours.
3. Once the desired level has been achieved, turn the
dial down until a maintenance setting is achieved.
4. The common maintenance setting for an average
bather load is #4.
When changing the setting, use bromine test strips to
determine when you have reached the level you want.
Once a Week
1. Test spa water with bromine test strip.
2. Based on test strip readings:
17. Put the cover on and allow the spa to heat to desired
temperature.
•
Adjust alkalinity if necessary.
•
Adjust pH if necessary.
Adjusting The Proper Bromine Levels
•
Increase / decrease bromine production with
dial if required.
1. After start up, decrease the filtration cycle to F-4
and monitor the bromine level until it is within the
recommended range.
2. Use bromine test strips to achieve a 3-5 ppm
recommended level.
Note: It can take several days for the bromine level to
stabilize because the fill water that was used sometimes
contains contaminants that need to be neutralized,
thereby using up the initial bromine that is generated.
3. Remove dirty filter from the spa and rinse off.
4. Place your clean, extra filter cartridge back into the
spa.
5. Add 2 oz of Cal Spas “Oxidizer Shock” to spa. Run
spa for 15 minutes
6. Vacuum debris from the bottom of your spa with the
“Spa Vacuum”.
7. Replace cover.
Maintenance Schedule
Regardless of which Clear Water Plan you are using,
you should also do the following:
Every Month
1. Deep clean your spa’s filter. (Follow filter cleaning
instruction at beginning of Clear Water Plan)
2. Check inside the equipment area for leaks, rodents,
and insects.
3. If a leak is discovered, contact your Cal Spas dealer
for service.
4. If you see evidence of rodents or insects, take
necessary actions to remove them and precautions
to prevent them from returning.
Every 3 To 4 Months
1. Drain and clean your spa with “Multi-Purpose
Cleaner”.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
2. Polish the acrylic surface with “Fast Sheen”.
3. Clean and treat spa cover, pillows, and Cal Select
cabinet (if equipped) with “Cover Protector”.
4. When re-filling your spa, follow your specific Clear
Water Plan Start Up procedures.
5. If you are using the Cal Clarity Automatic Bromine
Generator Clear Water Plan, don’t forget to add new
TRU BLU sodium bromide to the water.
Once A Year
1. Clean and treat redwood spa cabinets and
gazebos with “Nu-Spa Redwood Stain Renew and
Brightener”.
2. If you use the Cal Zone Quest 2000 Ozonator, you
will need to replace the ozone cartridge.
3. Check the filter cartridge pleats. If they are frayed,
replace the cartridge.
Page 27
Cleaning and Maintenance
Cleaning and Maintenance
Removing and Reseating the Pillows
You can remove the pillows for cleaning and maintenance quickly and easily. This method works for all types of
pillows.
Grab the lower edge of the pillow with both hands firmly and pull up. As you do this, the pillow inserts will pop out
of the holes.
Reseat the pillows by aligning the pillow inserts with the holes and striking the pillow hard enough to insert the pegs
back into the holes.
Spa Cover
Important! Keep the spa covered when not in use!
•
Covered spas will use less electricity in maintaining
your set temperature.
•
Covering your spa will protect your spa’s finish from
the sun’s ultraviolet rays.
•
You are required to keep the spa covered to maintain
warranty coverage.
•
Covering your spa helps prevent children from
drowning in the spa.
Page 28
See the manual enclosed with your cover for instructions
on mounting the locks and how to lock and unlock the
cover.
In addition, while the spa cover is rigid, it is not designed
to support any weight. Therefore, as a safety precaution
and to preserve the life of your cover, you must not sit,
stand, or lie on it; nor should you place objects of any
kind on top of it.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Cleaning and Maintenance
Draining Your Portable Spa
Your spa should be drained every four to six months, and refilled
with fresh tap water. The following is the recommended method
for draining your spa.
1. Turn off the power at the breaker.
2. Remove all filters.
If your drain valve is mounted on the side of the spa cabinet as
shown at right, proceed to step 5.
If your drain valve is located inside the spa cabinet:
3. Using a Phillips screwdriver, remove the screws to the
access panel and open it.
4. Locate hose ending with the 3/4 inch hose-bib fixture.
5. Hook up the female end of a garden hose to the drain fitting.
6. Place the other end of the garden hose where you would like the water to drain to.
7. Twist the hose-bib fixture counterclockwise and pull to open the drain.
8. Let spa drain completely, then remove garden hose.
9. Twist the hose-bib fixture clockwise to close it.
Winterizing (Cold Climate Draining)
In many areas of the country, the temperature drops below 32˚F (0°C). We recommend that you always have your
spa full of water and running at normal spa temperatures (80˚F to 100˚F, 26.7°C to 37.8°C). This will help reduce
the risk of freezing in your spa and your spa’s equipment.
Warning: If you find the need to drain your spa, please be aware of the potential of freezing in your spas
equipment and plumbing. Even if the directions below are followed perfectly, there is no guarantee that
your spa will not suffer freeze damage.
Freeze damage is not covered by your warranty.
1. Open all filter covers.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 29
Cleaning and Maintenance
2. Remove the filter baskets and filters.
All-Purpose Cleaner (Spa Finish cleaning)
3. Drain your spa completely as described in the
instructions above.
Cal Spas™ All-Purpose Cleaner is an
essential part of maintaining your spa’s
finish. Through normal use, the spa’s
finish can accumulate dirt, oil, and calcium
causing a rough feel and unsightly scum
lines. Cal Spas™ All-Purpose Cleaner
is a low detergent, non-abrasive cleaner
specifically formulated to clean the spa
without damaging its acrylic finish.
4. Remove drain plugs from the front of the pumps.
5. Disconnect the unions from both sides of the pump.
6. Use a wet/dry vacuum to blow any remaining water
out of the jets and equipment area.
Cover your spa with a good spa cover and an all-weather
tarp to ensure that neither rain nor snow enters the spa.
Cleaning the Cover, Shell and
Pillows
Due to the constant punishment your spa cover and
pillows receive, you should protect them by applying
Vinyl and Leather Cleaner as part of your monthly
maintenance plan. Cal Spas™ Vinyl and Leather
Cleaner is specifically designed to protect spa covers
and pillows from chemical and ultraviolet light damage. It
accomplishes this without leaving an oily residue behind
that is normally associated with common automotive
vinyl protectants.
The most effective solution to minimize
cleaning time is prevention. When the
following steps are followed, the spa’s finish will actually
start to resist most of the elements that cause calcium
build-up and make scum line clean up easier.
Prior to Spa Start-Up and Refilling
1. Spray Cal Spas™ Multi-Purpose Cleaner directly on
to the spa’s finish.
2. Wipe clean with a clean soft cloth.
3. Repeat on heavily calcified areas.
4. Wipe spa thoroughly with a wet sponge, rinsing
often with a bucket of clean water.
Use of Vinyl and Leather Cleaner
5. Allow spa to dry completely.
Cal Spas™ Vinyl and Leather Cleaner
should be used sparingly. Incorrect
usage may cause water clarity issues.
6. Apply a coat of Cal Spas™ Fast Sheen to the spa’s
entire finish with a soft towel or sponge.
Spa Covers
1. Remove spa cover from spa.
7. Allow Fast Sheen to dry until white and powdery.
8. Buff clean with a soft cloth, rotating frequently.
2. Allow spa cover to dry completely.
Periodic Maintenance
3. Spray Vinyl and Leather Cleaner
to cover evenly and wipe dry.
1. Spray Cal Spas™ Multi-Purpose Cleaner directly to
the spa’s finish.
4. Allow spa cover to dry completely.
2. Wipe clean with a clean soft cloth.
5. Reinstall cover on spa.
3. Wipe spa thoroughly with a wet sponge, rinsing
often in a bucket of clean water.
Pillows
1. Wipe pillows dry with a soft cloth.
2. Carefully spray Vinyl and Leather Cleaner directly
onto pillow.
3. Wipe pillows dry.
4. Allow pillows to dry completely.
Warning: Do not use automotive vinyl protectants on
spa covers or pillows. These products are generally oilbased and will cause severe water clarity issues that are
difficult to correct.
Page 30
Cal Spas™ Multi-Purpose Cleaner should not be
sprayed directly into the spa water. Incorrect usage of
this product will cause water clarity issues.
Fast Sheen (Spa Finish
Protecting Wax)
Cal Spas™ Fast Sheen is an essential
part of maintaining your spa’s finish.
Through normal use, the spa’s finish
can accumulate dirt, oil, and calcium,
causing a rough feel and unsightly scum
lines. Cal Spas™ Fast Sheen is a non-oil
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Cleaning and Maintenance
based wax that is specifically formulated to protect the
spa’s finish from the chemicals and minerals associated
with normal spa use.
The most effective solution to minimize cleaning time
is prevention. When the following steps are followed,
the spa’s finish will actually start to resist most of the
elements that cause calcium build-up and make scum
line clean-up easier.
the flow of water goes through the filter, dirt and debris is
removed and accumulated in the filter cartridge. As the
filter cartridge accumulates dirt and debris, water flow
is restricted and jet performance is reduced. This can
cause your spa to not run or heat effectively.
Clean your filter regularly and replace as needed.
Filter Cleaning
1. Spray Cal Spas™ Multi-Purpose Cleaner directly to
the spa’s finish.
Your new spa has been designed for quick and easy
filter maintenance. The filter cartridge should be cleaned
once a week. These instructions apply to both dual and
single filtration systems.
2. Wipe clean with a soft cloth.
1. Turn the power off at the breaker.
3. Repeat on heavily calcified areas.
2. Remove the filter by turning it counterclockwise and
unscrewing the bottom threads. Then pull it up and
out.
Prior to Spa Start-Up and Refilling
4. Wipe spa thoroughly with a wet sponge, rinsing
often in a bucket of clean water.
5. Allow the spa to dry completely.
6. Apply a coat of Cal Spas™ Fast Sheen to the spa’s
entire finish with a soft cloth or sponge.
7. Allow Fast Sheen to dry until white and powdery.
8. Buff clean with a soft cloth, rotating frequently.
IMPORTANT: Cal Spas™ Fast Sheen should not be
used on spas full of water. Only apply to clean, cool,
dry surfaces. Incorrect product usage may cause water
clarity issues.
Cleaning and Replacing the
Filter
Filtration
Filtration is one of the most important steps you can
take to ensure clean, clear water. Regardless of what
some people may think, it is far less expensive to fix
water clarity problems by filtering your spa than by using
excessive amounts of chemicals, excessive filtration
times, or by water replacement.
Cal Spas™ filtration system draws contaminated water
through the exclusive Bio-Clean™ filter removing debris
from the water. It then pumps the newly cleaned water
back into the spa through various jets. Spas equipped
with the optional Quest 2000 Ozonator will also receive
ozone injection into the filtered water for further protection
against contaminants during filtration cycles. Filtration
also ensures that chemicals are mixed thoroughly
through the water, increasing performance.
3. Clean the filter with a garden hose as follows:
a. Hold the filter vertically.
b. Spray the filter cartridges with a pressure nozzle,
starting from the top and spraying down each
pleat.
c.
Turn the filter cartridge over and repeat Step
3b.
d. Deep clean filter cartridge every month. Use
only a Cal Spas™-approved filter-cleaning
chemical.
Exclusive Bio-Clean™ Filter Cartridge
The filter cartridge is designed to remove dirt, sand,
minerals, phosphates, bather waste and other solids from
the spa. Unfortunately, some spa owners fail to include
filter cleaning as part of their chemical maintenance
plan. Filters accumulate debris and become prime areas
for bacteria growth.
The Cal Spas™ exclusive Bio-Clean™ Filter is the only
antibacterial filter cartridge on the market today. Having
a filter cartridge that prevents bacteria growth is added
protection for those times you forget to clean the filter.
We recommend that you only replace your spa’s filter
cartridge with a Bio-Clean™ filter cartridge for ensured
protection and peace of mind.
Filtration starts on electronically controlled spas as soon
as the pumps are primed and water flow is steady. As
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 31
Entertainment System
Using the Entertainment System
Some spas may be equipped with audio/visual
entertainment options. Several options are available
and include marine grade CD players, DVD players, and
an iPod® docking station. Two different TV monitors are
also available. Each spa equipped with an audio/visual
system is delivered with the manufacturer’s operating
instructions. We strongly recommend that you read
these instructions prior to operating the unit.
2. Press the left and right arrows located at the far right
of the panel to tune the radio to a station.
The instructions contained in this manual describe
only basic functions. See the manufacturer’s operating
instructions for other features and functions. These
instructions are delivered with the owner’s manual in a
clear plastic bag.
2. Insert a disk in the disk drive.
Observe the following precautions for your entertainment
system:
Playing a CD
•
Make sure that hands and CDs / DVDs are dry
before coming in contact with this or any electronic
option.
•
Always close the CD / DVD protective door.
•
Do not place wet CD’s or DVD’s into this unit at any
time.
•
Water damage is not covered by Cal Spas or the
manufacturer’s warranty.
Although the marine grade entertainment system is
encased in a plastic housing with weather seals, the
system is water resistant and NOT waterproof. You must
take every precaution to keep this system dry! Water
damage is not covered by Cal Spas or the manufacturer’s
warranty.
WARNING! Although the TV monitor is water resistant,
make sure that hands are dry before coming in contact
with this or any electronic option. DO NOT SPLASH
WATER ON THE TV MONITOR!
Operating the CD Player
The manufacturer’s operating instructions are delivered
with your spa. We strongly recommend that you read
these instructions prior to operating this unit.
Press the POWER button on the unit or the remote
control to turn the system on. The system automatically
starts in the mode it was in when it was last shut off.
Listening to the Radio
1. Press the MODE button to switch to the radio
mode.
Page 32
Inserting a Disk
For the Sony CDX-HS70MW and Aeware systems:
1. Press the OPEN button on the unit. The faceplate
will gently lower and expose the disk drive.
3. Flip up the faceplate.
For the Sony CDX-GT10M system, simply insert a disk
into the slot in the faceplate.
You can play CDs with any of the media systems (Sony
or Aeware).
1. Insert a disc in the disc drive as described above.
The player will identify the type of disc and begin
playing it.
2. Use either the remote control or the buttons on the
faceplate to start and stop the player and to jump to
selections.
3. To remove the disc, press the EJECT button.
Raising and Lowering the 20”
TV
Press the TV button on the auxiliary control panel to
raise and lower the TV monitor. Press the button once to
raise the TV. Press it again to lower the TV.
You can also press the OPT.1 button on the universal
remote.
Playing a Movie
This applies to the Aeware system only.
1. Press the OPT.1 button on the universal remote to
raise the TV.
2. Press the red POWER button to turn on the TV.
3. Insert a disc in the DVD player as described
above. The player will identify the type of disc and
begin playing it. Either the DVD menu will appear
on the TV screen or the movie will begin playing
automatically.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Entertainment System
4. Use the remote control to navigate the DVD menu using
the fast forward and fast reverse buttons located at the
lower part of the universal remote.
5. To remove the disc, press the OPEN button on the DVD
player. The faceplate will gently open. Press the small
EJECT button located to the left of the disk drive slot.
Using the iPod Docking Station
To play an iPod from the docking station to the spa’s stereo
system:
1. Place the iPod in the docking station.
2. Press the SOURCE button on the stereo (if equipped) until
the display shows AUX.
3. Play the iPod.
4. Adjust volume using the volume control in the docking
station.
Using the Universal Remote Control
Everything you want to do with your entertainment system can
be controlled with the universal remote. All of the commands
are organized into six areas.
Device selection buttons
Selects among six devices:
TV, VCR, CD player, DVD
player, stereo receiver, and
satellite
Navigation and menu
selection buttons
Selects among set-up, menu,
and channel guide functions
Channel and volume
control
Adjusts the volume up and
down
Spa controls
Selects among eight functions
specific to the spa, such as
blower, pumps and light
Keypad
Used to enter TV channels
CD and DVD controls
Use to control a CD or DVD
player
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 33
Entertainment System
Programming the Universal
Remote Control
The Cal Spas universal remote has been preprogrammed to function with the entertainment system
the spa has been configured with. However, in case you
need to reprogram the remote, use the device list below
for the programming code.
1. Turn on the device (TV, CD player, DVD player) with
the manufacturer’s remote control.
2. Press the button on the remote for the device you
want to program (TV, CD, DVD, etc.)
3. Press and hold the SETUP button until the LED
blinks twice.
4. Enter the device code. If you perform this procedure
correctly, the LED will blink twice. If not, repeat steps
2 and 3.
Device
Type
Code
Samsung 42” plasma
TV
1312
River Park 20”
TV
1530
DVD
1866
Device Manufacturer
Aeware
Sony CDX-GT10M
CD
Sony CDX-HS70MW
CD
Page 34
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Appendix
Appendix
Replacement Parts
Jet
Type
CXLW
CXW
E / EW
/ EP /
EPW
Description
Standard Gray Face
Stainless Steel Face
PLU21703421
PLU21703622
PLU21703425
PLU21703624
PLU21703420
PLU21703621
PLU21703430
PLU21703630
PLU21703431
PLU21703627
PLU21703432
PLU21703631
6.5” POWER STORM JET DIRECTIONAL
5.5”. POWER STORM JET, DIRECTIONAL
INTERNAL CLUSTER STORM, PULSATOR,
EURO
MFLW / 4.25”, STORM JET, MAXI FLOW W/ DRK
MFW
EYEBALL
MFRW
MFW
3.25”, STORM JET, MAXI FLOW W/DRK
EYEBALL
3.25”, STORM JET, MICRO FLOW W/DRK
EYEBALL
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 35
Appendix
MJLW
6.5”, POWER STORM JET, DIRECTIONAL
MJW
5.5”, POWER STORM JET, DIRECTIONAL
MNW
2.5”, NECK JET, QUAD BLASTER
MSRW
/ MFS
3”, STORM JET, MICRO SWIRL W/DRK
EYEBALL
SFW
5.5”, POWER STORM JET, SURE-FLO
S/
SJW /
SJ
5”, POWER STORM JET W/DRK EYEBALL
SW
STREAM (SWIM) JET COMPLETE
PLU21703422
PLU21703625
PLU21703423
PLU21703600
PLU21703427
PLU21703628
PLU21703433
PLU21703632
PLU21703426
PLU21703626
PLU21703429
PLU21700565
Page 36
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Appendix
SXW
5.5”, POWER STORM JET, SWIRLEY
TW
4.75”, POWER SWIM JET TORNADO
W
WHIRLPOOL
PLU21703424
PLU21703623
PLU21703428
PLU21703629
PLU21703122
OZONE INJECTOR JET
PLU21700818
DIRECTIONAL JET EURO
PLU21703643
AIR INJECTOR CAP
FIX12500050
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 37
Appendix
Valves
PLU21300052
DIVERTER VALVE 1” (2 WAY) SILVER, TEARDROP HANDLE (2 TONE)
PLU21300062
DIVERTER VALVE 2” (2 WAY) SILVER, TEARDROP HANDLE (2 TONE)
PLU21700378
VENT, 1” AIR CONTROL SILVER, TEARDROP (2 TONE)
PLU21700637
AROMATHERAPY CHAMBER AND CAP
Pillows
ACC01400884
QUAD BLASTER PILLOW
ACC01400874
NECK JET/ BLASTER PILLOW
ACC01400864
STD PILLOW, #965 RECTANGULAR
ACC01400886
PILLOW, VX
ACC01400479
PILLOW, FLOATING, GREY
ACC01400481
BOOSTER SEAT, GREY
Drains
PLU21400132
MAIN DRAIN, SUPER HI FLO SUCTION 2” SILVER
PLU21400155
HEAT RETURN
PLU21400197
BOTTOM DRAIN STAR SUCTION COVER
PLU21400065
HI FLO SUCTION SILVER 1 1/2”-
PLU21400195
BOTTOM DRAIN OZONE FITTING-
PLU21400196
BOTTOM DRAIN WALL FITTING-
OZO18300005
BOTTOM DRAIN-FILTRATION RETURN ASSY
Waterfalls
PLU21800618
WATERFALL SILVER
PLU21800611
WATERFALL SILVER, 4 PORT LED
PLU21800700
WATERFALL SILVER W/4” SLOT CLEAR FACE
PLU21800730
WATERFALL SILVER W/9” SLOT CLEAR FACE
PLU21800642
POP-UP WATERFALL
PLU21800800
WATERFALL SILVER AQUA SPRING 11”
Lights
LIT16100153
WALLFITTING, CLEAR LENS CAP, JUMBO SPA LIGHT, 5”
LIT16000151
LIGHT MINI 2-1/2 DIA
LIT16100155
RED LENS INSERT, JUMBO SPA LIGHT
LIT16100156
BLUE LENS INSERT, JUMBO SPA LIGHT,
Page 38
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Appendix
Filters
FIL11100190
FILTER CARTRIDGE, 50 SQ FT. ANTI-BACTERIAL RED
FIL11100191
FILTER CARTRIDGE, 75 SQ FT. ANTI-BACTERIAL WHITE
FIL11100193
FILTER CARTRIDGE, 35 SQ FT. ANTI-BACTERIAL WHITE
FIL11100125
FILTER CARTRIDGE CAL 75 SQ FT 10 1/16 X 15 1/6 (REMOTE EQUIPMENT)
FIL11703200
FILTER CARTRIDGE 75 SQ FT ANTI-BACTERIAL SCREW-IN
FIL11100200
FILTER CARTRIDGE, 50 SQ FT. ANTI-BACTERIAL WHITE, SCREW-IN
Pumps
PUM22000951
PUMP, 5.0 HP 2 SP SWITCHLESS, DBL SEAL 240V
PUM22000941
PUMP 6.0 HP 2SP 145T DBL SEAL, SWITCHLESS 2” 240V
PUM22000031
PUM 1.5 HP 2 SP 2” WET END 120V - 56 FRAME SWITCHLESS
PUM22000916
PUMP DUALLY, DBL SEAL SWITCHLESS 2” ULTIMA-240V
PUM22000952
PUMP 1.0 HP ATS – 240V
PUM22200051
PUMP, 1.5 BHP DUALLY GE-56 FRAME, DBL SEAL-120V
PUM22000977
24 HOUR FILTRATION PUMP ASSEMBLY 240V
PUM22100944
SPA CAL FILTRATION CIRC PUMP 240V
BLO05000085
BLOWER W/CORD COMPLETE 1.5 HP 240V 3.5 AMPS
PLU21100160
CHECK VALVE 1 ¼ lb.
1.5 HP 2 SP 48 FRAME
LED Lights
LIT16100179
SMALL CONTROLLER DAISY CHAIN
LIT16100183
2’ DAISY CHAIN JUMPER
LIT16100208
SILICONE O-RING FOR LENS
LIT16100209
OVERMOLD ADAPTER FOR SMALL CONTROLLER
LIT16100211
QUAD LED DAISY CHAIN ASSEMBLY
LIT16100212
DUAL LED DAISY CHAIN ASSEMBLY
LIT16100214
7 LED 2” LIGHT DAISY CHAIN WITH STAND-OFF
LIT16100215
FACETED BULLET LENS, POLYCARBONATE, UV STABLE
Cover Lifts
ACC01600116
COVER LIFT KIT, BOTTOM MOUNTING
ACC01600117
COVER LIFT ADJUSTABLE(top mount)
Hand Rails
FIX12400002
SWIVEL HAND RAIL
FIX12400003
SWIVEL HAND RAIL (BLACK)
Replacement Cabinet Panels
The complete selection of replacement cabinets for all models is very extensive and too lengthy for this owner’s
manual. See your Cal Spas deal to order replacement panels for your spa, or call 1-800-CAL-SPAS.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 39
Appendix
Covers
Standard Rust 5 to 3
Part No.
Description
Series
ACC01200420
SPA COVER STD
Aqua Series
ACC01200407
SPA COVER STD
Avalon 5 Series, J-502
ACC01200408
SPA COVER STD
J-501, H-902, J-504
ACC01200560
SPA COVER STD
H-901, S-702
ACC01200400
SPA COVER STD
S-704, S-705
ACC01200410
SPA COVER STD
J-503, 505, 506 S-703, 706, H-903, 704, 705, 706, 708, A-P, T
ACC01200420
SPA COVER STD
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
907, 908, A-L, B
ACC01200430
SPA COVER STD
CD-51
ACC01200450
SPA COVER STD
CN-36/51, S-709
ACC01200440
SPA COVER STD
CE-36/51
Standard Grey 5 to 3
Part No.
Description
Series
ACC01200421
SPA COVER STD
Aqua Series
ACC01200407
SPA COVER STD
Avalon 5 Series, J-502
ACC01200409
SPA COVER STD
J-501, H-902, J-504
ACC01200561
SPA COVER STD
H-901, S-702
ACC01200401
SPA COVER STD
S-704, S-705
ACC01200411
SPA COVER STD
C-P, C-T, J-503, J-505, J-506, S-703, S-706, A-P, T
ACC01200421
SPA COVER STD
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
907, 908, A-L, B
ACC01200431
SPA COVER STD
CD-51
ACC01200451
SPA COVER STD
CN-36/51, S-709
ACC01200441
SPA COVER STD
CE-36/51
Standard Slate 5 to 3
Part No.
Description
Series
ACC01200422
SPA COVER STD
Aqua Series
ACC01200508
SPA COVER STD
Avalon 5 Series, J-502
ACC01200510
SPA COVER STD
J-501, J-504, S-702
ACC01200562
SPA COVER STD
H-901, J-705, H-902
ACC01200402
SPA COVER STD
S-704
ACC01200412
SPA COVER STD
C-P,C-T,J-503,J-505,J-506, S-703, S-706, A-P, T
ACC01200422
SPA COVER STD
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
907, 908, A-L, B
ACC01200432
SPA COVER STD
CD-51
ACC01200452
SPA COVER STD
CN-36/51, S-709
ACC01200444
SPA COVER STD
CE-36/51
Page 40
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Appendix
Deluxe Rust 5 to 3
Part No.
Description
Series
ACU02200210
SPA COVER UL
C-B
ACU02200220
SPA COVER UL
C-K
ACU02200364
SPA COVER UL
J-501
ACU02200320
SPA COVER UL
C-O
ACU02200240
SPA COVER UL
C – V , S-704
ACU02200250
SPA COVER UL
C-P,C-T,J-503,J-505,J-506, S-703, S-706, A-P, T
ACU02200260
SPA COVER UL
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
906, 907, 908, GX49, A-L, B
ACU02200270
SPA COVER UL
C-D
ACU02200290
SPA COVER UL
C – N, S-709
ACU02200280
SPA COVER UL
C-E
ACU02200310
SPA COVER UL
C-R
ACU02200330
SPA COVER UL
C-A
Deluxe Grey 5 to 3
Part No.
Description
Series
ACU02200211
SPA COVER UL
C-B
ACU02200221
SPA COVER UL
C-K
ACU02200365
SPA COVER UL
J-501
ACU02200321
SPA COVER UL
C-O
ACU02200241
SPA COVER UL
C – V, S-704
ACU02200251
SPA COVER UL
C-P, C-T, J503, J505, J506, S703, S706
ACU02200261
SPA COVER UL
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
906, 907, 908, GX-49
ACU02200271
SPA COVER UL
C-D
ACU02200291
SPA COVER UL
C – N, S-709
ACU02200281
SPA COVER UL
C-E
ACU02200311
SPA COVER UL
C-R
ACU02200331
SPA COVER UL
C-A
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 41
Appendix
Deluxe Slate 5 to 3
Part No.
Description
Series
ACU02200216
SPA COVER UL
C-B
ACU02200225
SPA COVER UL
C-K
ACU02200368
SPA COVER UL
J-501
ACU02200325
SPA COVER UL
C-O
ACU02200246
SPA COVER UL
C – V, S-704
ACU02200256
SPA COVER UL
C-P,C-T,J-503,J-505,J-506, S-703, S-706
ACU02200266
SPA COVER UL
C- A,C,M,LBA, J-507,J-508, S-707, S-708, H903,904,905,906,90
7,908, GX-49
ACU02200275
SPA COVER UL
C-D
ACU02200295
SPA COVER UL
C – N, S-709
ACU02200285
SPA COVER UL
C-E
Deluxe Teal 5 to 3
Part No.
Description
Series
ACU02200212
SPA COVER UL
C-B
ACU02200222
SPA COVER UL
C-K
ACU02200369
SPA COVER UL
J-501
ACU02200242
SPA COVER UL
C-O
ACU02200252
SPA COVER UL
C – V, S-704
ACU02200262
SPA COVER UL
C-P, C-T, J-503, J-505, J-506, S-703, S-706
ACU02200272
SPA COVER UL
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
906, 907, 908, GX-49
ACU02200292
SPA COVER UL
C–D
ACU02200282
SPA COVER UL
C – N, S-709
Deluxe Navy 5 to 3
Part No.
Description
Series
ACU02200213
SPA COVER UL
C-B
ACU02200223
SPA COVER UL
C-K
ACU02200370
SPA COVER UL
J-501
ACU02200323
SPA COVER UL
C-O
ACU02200243
SPA COVER UL
S-704
ACU02200253
SPA COVER UL
C-P, C-T, J-503, J-505, J-506, S-703, S-706
ACU02200263
SPA COVER UL
C- A, C, M, LBA, J-507, J-508, S-707, S-708, H-903, 904, 905,
906, 907, 908, GX-49
ACU02200273
SPA COVER UL
C–D
ACU02200293
SPA COVER UL
C – N, S-709
ACU02200283
SPA COVER UL
C–E
Page 42
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Appendix
Keeping Fit with your Spa
IMPORTANT: Always consult your physician before starting any exercise activity or program. The Ultimate Fitness
series spas feature rubber exercise bands. When stretched, these bands create a high tension condition. Improper
use or failure to connect the exercise bands properly may cause injury. Always inspect all of the exercise equipment
prior to beginning any exercise. Do not use any damaged equipment
The fitness equipment consists of: two rowing arm bars, two 62” exercise bands, two 32” exercise bands, two 27”
exercise bands, two hand grips, two ankle bands, two hand loops, and an exercise belt. This equipment attaches
to the exercise anchors located on the spa walls.
Ultimate Fitness Series Exercise Program
Refer to the equipment configurations shown on the next page for the following exercises.
Seated Row
Use the exercise bars in a seated position with your
feet stable, abs tight and lower back stable. Keep your
palms down, arms extended with elbows slightly bent.
Pull towards your chest squeezing your shoulder blades
to the middle back and returning slowly to the starting
position.
Standing Chest Fly
Using the exercise grips, place palms sideways facing
your body with your elbows slightly bent. Pull your body
forward, bringing hands together, squeezing and flexing
chest muscles, then slowly returning to the starting
position.
Standing Chest Press
Using the exercise grips, place your palms down with
your elbows bent at 90˚. Press forward bringing your
hands together, squeezing and flexing your chest
muscles, then slowly return to the start position.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Standing Shoulder Press
Using the exercise grips, place your palms facing away
from your body with your elbows bent at 90˚. Press
upward bringing your hands together in front of you,
above your head and slowly return to the start position.
Arm Curls
Using the exercise grips, place your hands face up with
your elbows slightly bent, pull upward towards your chin
squeezing and flexing your biceps then slowly return to
start position.
Running or Walking
Attach the exercise belt around your waist and attach the
two 62” exercise bands to the far wall of the spa. Turn on
the two swim jets and walk or run into jet stream.
Leg Streching and Strength Training
Attach an ankle band to your ankle and attach a 62”
exercise band to any exercise anchor. Lift your leg to the
side or back as the band provides tension.
Page 43
Appendix
Connecting the Exercise Equipment
The drawings below show different ways the exercise
kit can be connected depending on the exercises you
wish to do.
Page 44
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Appendix
Cal Spas™ Chemicals
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 45
U.S. and Canada
Portable Spas
2008 Warranty
This limited warranty is effective for portable spas manufactured after January 14, 2008
Spa Shell / Structural
LMS warrants against the loss of water through the spa shell due
to defects in materials and/or workmanship for a period of 10
years from the original date of purchase.
Interior Surface – Altair Plus / Quarite Plus
LMS warrants against cracks, blisters, peeling, discoloration and
delamination of Altair Plus / Quarite Plus interior surfaces for a
period of ten years from the original date of purchase.
Interior Surface – Standard Acrylic / Quarite
LMS warrants against cracks, blisters, peeling, discoloration and
delamination of standard acrylic/quarite interior surfaces for a
period of five years from the original date of purchase.
Equipment
LMS warrants the spa’s electrical and electronic components,
specifically: the control system, pumps and air blowers against
malfunction due to defects in materials and/or workmanship for a
period of five years from the original date of purchase.
Plumbing
LMS warrants all factory installed plumbing and Eliminator™
Plus Wet Ends from loss of water due to defects in material and/
or workmanship for a period of five years from the original date
of purchase.
Cabinets
LMS warrants Cal Premium™, Cal Select™ and Cal Stone™
panels against cracking and warping for a period of three years
from the original date of purchase.
Components
LMS warrants manufacturer-installed XL Heat Exchanger™ and
Cal Zone Quest 2000 Ozonator™ against malfunction due to
defects in materials and/or workmanship for the lifetime of the
spa.
Electrical and Electronic Components
LMS warrants stereos, DVD players, TVs and the LED light source
for a period of one year from the original date of purchase.
Manufacturer Warranty
All Cal Spas hot tubs are manufactured with the highest quality appliances
and are warranted to be free from defects in material and workmanship at
the time of delivery. Cal Spas electronic component warranty is extended
through the manufacturer of the product including, but not limited to:
televisions, stereos, DVD players, etc.
Proration of Warranty
Units determined by the Company to be non-repairable will be replaced
on a prorated basis with the same or a comparable unit. The user will
be charged one percent of the current retail cost for each full month of
ownership from the date of purchase through the date failure is determined
to be non-repairable. This charge will be waived during the first twelve
months of ownership.
Warranty Performance
In the event of a malfunction or defect covered under the terms of this
warranty, the factory authorized selling dealer is responsible for performing
all necessary repairs. To obtain service, contact the selling dealer. In the
event the consumer is unable to obtain satisfactory customer service from
the selling dealer, written notification must be given to the LMS Customer
Relations Department within 30 days of the reported failure. There will be
no charge for parts or labor on a covered item. However, the LMS Service
Agent may assess a reasonable travel or mileage charge per service call,
which may include diagnostic time. If LMS determines that repair of a
covered item is not feasible, LMS reserves the right to replace the defective
merchandise with merchandise equivalent or equal in value to the original
merchandise. In the event of any warranty replacement, all removal,
replacement, installation and shipping costs are the responsibility of the
spa owner.
Warranty Exclusions and Limitations
This warranty is void if the spa has been subject to negligence, alteration,
misuse, abuse, repairs by non-LMS authorized personnel, incorrect electrical
installation, installation of any component other than by the manufacturer,
acts of God (including, but not limited to, acts of nature and surrounding
environments), and any other cases beyond the control of LMS Refer to
the owner’s manual for further information and examples of exclusions and
common acts invalidating this warranty. This warranty excludes Designer
Series in-ground spas.
Disclaimers
This limited warranty is made with the express understanding that the spa
is not an essential device or medical device as defined under State and
Federal Law. LMS shall not be liable for loss of use of the spa or other
incidental or consequential costs, expense or damages, which may include
but are not limited to removal of permanent deck or other custom fixtures or
the necessity for crane removal. Any implied warranty shall have duration
equal of the applicable warranty stated above. Under no circumstances
shall LMS or any of its representatives be held liable for injury to any person
or damage to any property, however arising.
Legal Remedies
This limited warranty gives you specific legal rights and you may have other
rights, which may vary from state to state.
Extent of Warranty
This limited warranty is only valid on portable hot tubs delivered in the United
States and Canada. However, it does not apply to special offers and events
and extends through the selling dealer to the original purchaser at the
original site of installation. This warranty becomes valid at time of purchase
and ends either by specified time-frame listed above, owner-transfer,
relocation, or installation of any component other than by manufacturer.
The Designer series in-ground spas are excluded from this warranty.
Customer Service
For customer service, contact the authorized selling dealer immediately.
If you need additional information or assistance, please contact the LMS
Customer Relations Department at 1462 E. Ninth St., Pomona CA 91766
or call (800) 225-7727.
Appendix
See your Cal Spas™ dealer for a copy of the applicable warranty, details, and any questions you may have regarding
the warranty coverage on your spa.
Warranty Specifics
•
Five Year Cabinet Warranty: Cabinet surface peeling, blistering, fading, or delamination are specifically excluded
from this warranty.
•
Lifetime Warranty on XL Heat Exchanger and Quest 2000 Ozonator: After original five-year coverage from date
of delivery, lifetime warranty covers parts only. Specifically excludes replacement ozone cartridge, which has a
one year warranty
•
One Year Spa Cover Warranty: Spa covers are warranted for one year by manufacturer unless otherwise
specified.
Warranty Limitations
The 2008 Limited Warranty is void if the spa has been subject to negligence, alteration, misuse, abuse, repairs by
non-LMS authorized representatives, incorrect electrical installation, acts of God and any other cases beyond the
control of LMS Examples of common acts invalidating this warranty include, but are not limited to:
•
Use of spa in a non-residential application.
•
Scratches caused by normal use.
•
Operation of spas water temperature out of the normal operating range of 32˚F (0°C) to 118˚F (47.8°C).
•
Damage caused by incorrect water level (low, overflow, etc.).
•
Damage caused by extreme weather conditions (hot, cold, etc.).
•
Damage caused by dirt, sand and calcium.
•
Damage caused by clogged filter cartridges. See filter cleaning recommendations in this owner’s manual.
•
Damage caused by continued operation of this spa with either a known or an unknown problem.
•
Damage caused by tri-chlor, acids, chlorine tablets, any floating chemical devices, or any spa chemicals not
authorized by LMS
•
Damage caused by improper water chemistry. (High levels of chlorine, bromine, calcium, pH and other excessive
chemical levels.)
•
Damage caused by direct sunlight. Spas should always be covered when not in use.
•
Damage caused as a result of failure to follow operating instructions as defined within this owner’s manual.
•
Damage caused by incorrect electrical installation, electrical brownout, voltage spikes, or operation of spa out
of voltage range by more than ±10%.
•
Spas improperly installed or placed on non-approved surfaces.
Although shell cracks, which are breaks in the shell that go all the way through, are covered by this limited warranty,
cosmetic scratches, gouges and crazing are not considered cracks and are not covered.
The limited warranty applies only to spas normally used for personal, family or household purposes.
For relocating your spa without voiding your warranty, contact Customer Service for relocation procedures.
Warranty Exclusions
Replaceable service items such as filters, light bulbs, pillows, jet inserts, and filter covers are specifically excluded
from the limited warranty.
Spa covers and stereo systems are delivered with their own manufacturer’s warranty. For more information, please
see their warranties in the owner’s information package that was delivered with your spa for more information.
Equipment adjustments (such as pressure switch adjustments) are specifically excluded from this warranty.
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 47
Page 48
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
2008 Portable Spa Owner’s Manual
LTR20081000, Rev. B
Page 49
Locating the product serial number
The serial number of your spa is located on a metal plate attached to the
lower right front panel of the spa.You will need this number to properly
register your spa and activate coverage. Write this information in the space
provided below.
Spa Model: __________________________________________________
Spa Serial Number: _ __________________________________________
Date Purchased: ______________________________________________
Date Installed: ________________________________________________
Dealer’s Phone Number: _ ______________________________________
Dealer’s Address: _____________________________________________
CONTACT INFORMATION
For customer service, please contact your authorized dealer immediately. If you need additional information and/or
assistance, please contact:
LMS Customer Service Department
1462 East Ninth Street
Pomona, CA 91766.
Toll Free: 1-800-CAL-SPAS
Fax: 1-909-629-3890
www.calspas.com