Alliance Laundry Systems 70269501R3 Snow Blower User Manual

Operation/Maintenance
Drying Tumblers
25 Pound Capacity
30 Pound Capacity
35 Pound Capacity
Stacked 30 Pound Capacity
Through Serial No. 0602004143
Refer to Page 5 for Model Numbers
NOTA: Para bajar una
copia de estas
instrucciones en
español, visite
www.comlaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. 70269501R3
August 2006
Installation must conform with local codes or in the absence of local codes with:
In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/
NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.”
In Canada, installation must comply with Standards CSA-B149.1 or Natural Gas and Propane Code CSA
C22.1, latest edition, Canadian Electric Code, Part I.
In Australia, installation must comply with the Australian Gas Association Installation Code for Gas
Burning Appliances and Equipment.
WARNING
MISE EN GARDE
FOR YOUR SAFETY, the information in this
manual must be followed to minimize the
risk of fire or explosion or to prevent
property damage, personal injury or death.
W033
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do
not use any phone in your building.
– Clear the room, building or area of all
occupants.
– Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
– If you cannot reach your gas supplier,
call the fire department.
• Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
W052
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
W053
POUR VOTRE SÉCURITÉ, veillez à bien
respecter les indications de ce manuel afin
de minimiser les risques d’incendie ou
d’explosion ou d’écarter les dangers de
dommages matériels, corporel ou de mort.
W033FR
• Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides
inflammables dans le voisinage de cet
appareil ou de tout autre appareil.
• QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ :
– Ne pas tenter d’allumer d’apareil.
– Ne touchez à aucun interrupteur. Ne
pas vous servir des téléphones se
trouvant dans le bâtiment où vous vous
trouvez.
– Évacuez la pièce, le bâtiment ou la
zone.
– Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.
– Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.
• L’installation et l’entretien doivent être
assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
de gaz.
W052Q
POUR VOTRE SÉCURITÉ
Ne pas entreposer ni utiliser d’essence ou
autres gaz et liquides inflammables au
voisinage de cet appareil ou de tout autre.
W053FR
IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the
user smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the
above safety information must be posted in a prominent location near the tumbler for customer use.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Notes
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Table of
Contents
Introduction.........................................................................................
Model Identification .............................................................................
Customer Service..................................................................................
Wiring Diagram ....................................................................................
Serial Plate Location.............................................................................
5
5
6
6
6
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
7
7
8
Operating Instructions .......................................................................
Emergency Stop Button on CE Models................................................
Operating Instructions ..........................................................................
Step 1: Clean Lint Screen/Compartment .........................................
Step 2: Load Laundry.......................................................................
Step 3: Determine Control Type and Temperature Setting .............
Step 4: Remove Laundry .................................................................
Electromechanical Coin Control......................................................
Electronic Coin Control ...................................................................
Manual Timer...................................................................................
Electronic OPL Control ...................................................................
MDC Coin Control ..........................................................................
MDC Card Control ..........................................................................
NetMaster Coin Control...................................................................
NetMaster Card Control...................................................................
11
11
11
11
11
11
11
12
13
14
15
16
17
18
19
Maintenance ........................................................................................
Daily .....................................................................................................
Monthly.................................................................................................
Quarterly ...............................................................................................
Bi-Annually ..........................................................................................
21
21
23
23
23
Before You Call for Service ............................................................... 27
Customer Service.................................................................................. 27
© Copyright 2006, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Notes
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Introduction
Model Identification
Information in this manual is applicable to these models.
Gas
25 Pound
30 Pound
T30
35 Pound
HA025L
HA025N
HT025L
HT025N
HU025L
HU025N
SA025L
HA030L
HA030N
HT030D
HT030L
HT030N
HU030L
HU030N
HAT30L
HAT30N
HTT30D
HTT30L
HTT30N
AT035L
AT035N
HA035L
HA035N
HT035L
HT035N
HU035L
HU035N
SA025N
ST025L
ST025N
SU025L
SU025N
UA025L
UA025N
SA030L
SA030N
ST030L
ST030N
SU030L
SU030N
UA030L
HUT30L
HUT30N
MTT30N
NTT30N
SAT30L
SA035L
SA035N
ST035L
ST035N
SU035L
SU035N
UA035L
UA035N
Steam
Electric
UT025L
UT025N
UU025L
UU025N
YT025L
YT025N
HT025S
HU025S
ST025S
SU025S
UT025S
UU025S
YT025S
HT025E
HU025E
ST025E
SU025E
UT025E
UU025E
YT025E
UA030N
UT030L
UT030N
UU030L
UU030N
YT030L
YT030N
SAT30N
STT30L
STT30N
SUT30L
SUT30N
UT035L
UT035N
UU035L
UU035N
YT035L
YT035N
HT030S
HU030S
ST030S
SU030S
UT030S
UU030S
YT030S
HT030E
HU030E
ST030E
SU030E
UT030E
UU030E
YT030E
HTT30S
HUT30S
STT30S
SUT30S
HTT30E
HUT30E
STT30E
SUT30E
AT035S
HT035S
HU035S
ST035S
SU035S
UT035S
UU035S
YT035S
YU035S
HT035E
HU035E
ST035E
SU035E
UT035E
UU035E
YT035E
YU035E
Includes models with control suffixes:
BC – basic electronic, coin
BL – basic electronic, central pay
BX – basic electronic, prep for coin
BY – basic electronic, prep for card
CD – rotary coin drop
CX – prep for coin
CY – prep for card
70269501
EC – EDC electronic coin
EX – EDC coin ready
EY – EDC card ready
MT – manual timer
NC – NetMaster coin
NR – NetMaster card
NX – NetMaster, prep for coin
NY – NetMaster, prep for card
OM – OPL micro
ZC – NetMaster network coin
ZR – NetMaster network card
ZX – NetMaster network, prep for coin
ZY – NetMaster network, prep for card
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Introduction
Customer Service
Serial Plate Location
When calling or writing for information about your
product, be sure to mention model and serial numbers.
Model and serial numbers are found on serial plate on
rear of machine, and inside door hinge. Refer to
Figure 1.
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
For technical assistance, call (920) 748-3121.
Wiring Diagram
The wiring diagram is located in the junction or
contactor box.
Models starting Serial No. 0309_____ or later will
have the wiring diagram part number in the lower
portion of the electrical data on the serial plate.
1
1
25, 30 AND 35 POUND TUMBLERS
T30
TMB2025N
TMB2025N
1
Serial plate
Figure 1
Conversion Table
Multiply
To Obtain
Multiply
By
To Obtain
Btu
0.252
kCal
Pounds/sq. inch
0.06895
Btu
1055
Joules
Pounds/sq. inch
0.070
kg/sq. cm
Inch
25.4
Millimeters
Pounds (lbs.)
0.454
Kilograms
Inches W.C.
0.036
Pounds/sq. inch
Boiler Horsepower
33,479
Btu/hr.
Inches W.C.
0.249
kPa
Boiler Horsepower
34.5
lbs. steam/hr.
lb/inch (psi)
6.895
kPa
CFM
0.471
liters/second
ft3
28.32
Liters
kW
3414
Btu/hr.
2
6
By
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Bars
70269501
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
DANGER
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
CAUTION
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
IMPORTANT: Warranty is void unless tumbler
is installed according to instructions in the
Installation Manual. Compliance with minimum
specifications and requirements detailed herein,
and with applicable local gas fitting regulations,
municipal building codes, water supply regulations,
electrical wiring regulations, and any other
relevant statutory regulations. Because of varied
requirements, applicable local codes should be
thoroughly understood and all pre-installation
work arranged for accordingly.
WARNING
Failure to install, maintain, and/or operate
this machine according to manufacturer’s
instructions may result in conditions which
can produce serious injury, death and/or
property damage.
W051R1
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not
meant to cover all possible conditions and
situations that may occur. It must be understood
that common sense, caution and carefulness are
factors which CANNOT be built into this tumbler.
These factors MUST BE supplied by the person(s)
installing, maintaining or operating the tumbler.
Always contact your dealer, distributor, service agent
or the manufacturer on any problems or conditions you
do not understand.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Safety Information
Important Safety Instructions
14. The interior of the tumbler and the exhaust duct
should be cleaned periodically by qualified
service personnel.
Save These Instructions
WARNING
Hazardous Voltage. Can cause shock, burn
or cause death. Allow machine power to
remain off for two minutes prior to working
in and around AC inverter drive.
W359
1. Read all instructions before using the tumbler.
2. Refer to the GROUNDING INSTRUCTIONS
for the proper grounding of the tumbler.
3. Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, other flammable
or explosive substances as they give off vapors
that could ignite or explode.
4. Do not allow children on or in the tumbler. This
appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
15. If not installed, operated and maintained in
accordance with the manufacturer’s instructions
or if there is damage to or mishandling of this
product’s components, use of this product could
expose you to substances in the fuel or from fuel
combustion which can cause death or serious
illness and which are known to the State of
California to cause cancer, birth defects or other
reproductive harm.
16. Tumbler will not operate with the loading door
open. DO NOT bypass the door safety switch to
permit the tumbler to operate with the door open.
The tumbler will stop tumbling when the door is
opened. Do not use the tumbler if it does not stop
tumbling when the door is opened or starts
tumbling without pressing or turning the START
mechanism. Remove the tumbler from use and
call for service.
17. Tumbler will not operate with lint panel open.
DO NOT bypass lint panel safety switch to
permit the tumbler to operate with the lint panel
open.
5. Before the tumbler is removed from service or
discarded, remove the door to the drying
compartment and the door to the lint
compartment.
18. Do not put articles soiled with vegetable or cooking
oil in the tumbler, as these oils may not be
removed during washing. Due to the remaining
oil, the fabric may catch on fire by itself.
6. Do not reach into the tumbler if the cylinder is
revolving.
19. To reduce the risk of fire, DO NOT put clothes
which have traces of any flammable substances
such as machine oil, flammable chemicals,
thinner, etc. or anything containing wax or
chemicals such as in mops and cleaning cloths, or
anything dry-cleaned at home with dry-cleaning
solvent in the tumbler.
7. Do not install or store the tumbler where it will
be exposed to water and/or weather.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the tumbler,
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
10. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
11. To reduce the risk of fire, DO NOT DRY plastics
or articles containing foam rubber or similarly
textured rubberlike materials.
20. Use the tumbler only for its intended purpose,
drying fabrics.
21. ALWAYS disconnect and lockout the electrical
power to the tumbler before servicing. Disconnect
power by shutting off appropriate breaker or fuse.
22. Install this tumbler according to the
INSTALLATION INSTRUCTIONS. All
connections for electrical power, grounding, and
gas supply must comply with local codes and be
made by licensed personnel when required.
12. Always clean the lint filter daily.
13. Keep area around the exhaust opening and
adjacent surrounding area free from the
accumulation of lint, dust and dirt.
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Safety Information
23. Remove laundry immediately after tumbler
stops.
24. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of reach of children at all times
(preferably in a locked cabinet).
25. Do not tumble fiberglass curtains and draperies
unless the label says it can be done. If they are
dried, wipe out the cylinder with a damp cloth to
remove particles of fiberglass.
26. Always follow the fabric care instructions
supplied by the garment manufacturer.
27. Never operate the tumbler with any guards and/or
panels removed.
29. DO NOT bypass any safety devices.
30. Solvent vapors from dry-cleaning machines
create acids when drawn through the heater of the
drying unit. These acids are corrosive to the
tumbler as well as to the laundry load being
dried. Be sure make-up air is free of solvent
vapors.
31. Failure to install, maintain, and/or operate this
machine according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
WARNING
To reduce the risk of serious injury, install
lockable door(s) to prevent public access
to rear of tumblers.
28. DO NOT operate the tumbler if it is smoking,
grinding, has missing or broken parts.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
W055
9
Notes
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Operating Instructions
WARNING
To reduce the risk of fire:
• DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials.
• DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning
cloths, or anything dry-cleaned at home with a dry-cleaning solvent.
• DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done. If
they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.
W076
To reduce the risk of serious injury, allow cylinder to stop before cleaning lint screen.
W412
Emergency Stop Button on CE
Models
Operating Instructions
Step 1: Clean Lint Screen/Compartment
All CE approved OPL tumblers are factory equipped
with an emergency stop button located on the front
panel. Refer to Figure 2.
1
Remove any accumulated lint from the lint screen and
compartment. Close panel tightly against tumbler
frame and lock panel securely, if applicable.
IMPORTANT: Clean lint screen and lint
compartment daily. Failure to clean the lint screen
daily will result in higher than normal
temperatures that may damage laundry.
Step 2: Load Laundry
Open loading door and load cylinder with laundry. DO
NOT OVERLOAD.
NOTE: Overloading causes slow drying and
wrinkling.
TMB1664N
Emergency Stop Button
1
Figure 2
To operate emergency stop button:
Close loading door. Tumbler will not operate with the
door open.
Step 3: Determine Control Type and
Temperature Setting
a. Press red emergency stop button to stop all
action.
Refer to the various controls, pages 12 - 19, and follow
instructions for the appropriate control type.
b. To restart machine, pull red emergency stop
button out and press START pad or button.
T30 models only: use the correct coin slot and control
panel for the top or bottom cylinder.
NOTE: Activation of the emergency stop button
stops all machine control circuit functions, but
DOES NOT remove all electrical power from
machine.
The type of fabric being dried will determine the
setting. Consult the fabric care label or fabric
manufacturer to determine proper temperature setting.
IMPORTANT: Always follow the fabric care
instructions supplied by the garment manufacturer.
Step 4: Remove Laundry
When the cycle is complete, open door and remove the
laundry.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Operating Instructions
1
HIGH
2
SELECT
TEMP
TEMPERATURE
3
INSERT
COIN
PUSH
START
LOW
INSERT QUARTER
TURN KNOB
QU
PUSH
TO
START
25
ARTE
RMAST
ER
TMB807N
Figure 3
Electromechanical Coin Control
CD, CX and CY Control Suffixes
1. Set the TEMPERATURE selector at HIGH or
LOW, or anywhere between these settings.
2. Coin Drop Models: Insert the coin(s) in the coin
slot, turn the knob to the right and release it.
3. Press the PUSH TO START button and hold it for
approximately three (3) seconds.
NOTE: Additional drying time may be purchased
at cycle start, or while tumbler is running, by
adding additional coin(s).
IMPORTANT: If the loading door or lint panel
door is opened during the cycle, the heating system
will shut off and the motor will stop. However, the
timer will continue to run. To restart the cycle, both
doors must be closed and the PUSH TO START
button must be pressed in.
4. When the cycle is complete, open door and
remove the laundry.
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Operating Instructions
1
2
SELECT
TEMP
3
INSERT
COIN
PUSH
START
25 C
HIGH
TEMP
MED
TEMP
START
LOW
TEMP
NO
HEAT
T361I
T361I
Figure 4
Electronic Coin Control
EC, EX and EY Control Suffixes
1. Select HIGH TEMP, MED TEMP, LOW TEMP
or NO HEAT by pressing the appropriate
temperature pad.
2. Insert the coin(s) in the coin slot.
3. Press START pad to start tumbler.
70269501
NOTE: Additional drying time may be purchased
at cycle start, or while tumbler is running, by
adding additional coin(s).
IMPORTANT: To stop the tumbler at any time
during the cycle, OPEN DOOR. To restart the
tumbler, CLOSE door and press START pad.
4. When the cycle is complete, open door and
remove the laundry.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Operating Instructions
1
2
0
60
10
0
15
50
20
40
5
HEAT
10
30
HIGH
4
PUSH
TO
START
COOL
DOWN
LOW
3
TMB47N
Figure 5
Manual Timer
MT Control Suffix
1. Set the HEAT (Drying) timer for the number of
minutes (from 0-60) desired.
2. Set the COOL DOWN (Cooling) timer for the
number of minutes (from 0-15) desired.
IMPORTANT: If the door is opened during the
cycle, the heating system will shut off and the
motor will stop. To restart the cycle, door must be
closed and the PUSH TO START button must be
pressed in.
5. When the cycle is complete, open door and
remove the laundry.
3. Set the Temperature selector at HIGH, LOW or
anywhere between these settings.
4. Press the PUSH TO START button in and hold it
in for approximately three seconds. This starts
the tumbler cycle.
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Operating Instructions
STATUS
ON / SELECT
HIGH
START
PROGRAM
AUTO
DRYING
TIME
AUTO
MEDIUM
MED LOW
TEMP
DISPLAY
LOW
SIGNAL
SPECIAL
CYCLE
COOL DOWN
STOP/RESET
*
DOOR OPEN
AUTO
TEMP
SPECIAL
TIME
*
COOL
DOWN
F/ C
CUSTOM
NO HEAT
MORE
+
LESS
CONDITION
SAVE
CUSTOM
--
PROG
TMB1789N
TMB1789N
Figure 6
Electronic OPL Control
2. Press START pad to start tumbler.
OM Control Suffix
1. To use an Automatic Cycle, press an ON/
SELECT pad. Select HIGH, MEDIUM,
MED LOW, LOW or NO HEAT for items that
should not be dried with heat. A light to the left
of the selected pad lights up.
To use a Time Dry or Custom Cycle, refer to the
Programming Manual.
NOTE: Do not press directly on lights or the center
of pad. For proper selection, press on pad slightly
to the right of center. Refer to Figure 7.
NOTE: All pads can be pressed in any sequence
without damaging control or tumbler. To stop the
tumbler at any time, open the door or press STOP/
RESET. The window display will flash. Press
STOP/RESET twice (within 3 seconds) to end the
cycle and reset the control to idle status. To restart
the tumbler, CLOSE door and press START pad.
IMPORTANT: If the loading door or lint panel
door is opened during the cycle, the heating system
will shut off and the motor will stop. To restart the
cycle, both doors must be closed and the PUSH TO
START button must be pressed in.
3. When the cycle is complete, open door and
remove the laundry.
TMB806N
TMB806N
Figure 7
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Operating Instructions
SELECT
TEMP
INSERT
COINS
or
INSERT
CARD
PUSH
START
25 C
DRYING
COOL
DOWN
DELICATES
START
TMB1964N
Figure 8
MDC Coin Control
BC and BX Control Suffixes
1. Select HIGH TEMP, MED TEMP, LOW TEMP
or DELICATES by pressing the appropriate
temperature pad.
IMPORTANT: To stop the tumbler at any time
during the cycle, OPEN DOOR. To restart the
tumbler, CLOSE door and press START pad.
4. When the cycle is complete, open door and
remove the laundry.
2. Insert the coin(s) in the coin slot.
3. Press START pad to start tumbler.
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Operating Instructions
SELECT
TEMP
DRYING
PUSH
START
COOL
DOWN
INSERT CARD HERE
DELICATES
START
TMB1965N
Figure 9
MDC Card Control
BL and BY Control Suffixes
1. Select HIGH TEMP, MED TEMP, LOW TEMP
or DELICATES by pressing the appropriate
temperature pad.
IMPORTANT: To stop the tumbler at any time
during the cycle, OPEN DOOR. To restart the
tumbler, CLOSE door and press START pad.
4. When the cycle is complete, open door and
remove the laundry.
2. Insert card into opening.
3. Press START pad to start tumbler.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Operating Instructions
C851I
C851I
Figure 10
NetMaster Coin Control
NC, NX, ZC and ZX Control Suffixes
1. Select HIGH TEMP, MED TEMP, LOW TEMP
or NO HEAT by pressing the appropriate
temperature pad.
IMPORTANT: To stop the tumbler at any time
during the cycle, OPEN DOOR. To restart the
tumbler, CLOSE door and press START pad.
4. When the cycle is complete, open door and
remove the laundry.
2. Insert the coin(s) in the coin slot.
3. Press START pad to start tumbler.
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Operating Instructions
C852I
C852I
Figure 11
NetMaster Card Control
NR, NY, ZR and ZY Control Suffixes
1. Select HIGH TEMP, MED TEMP, LOW TEMP
or NO HEAT by pressing the appropriate
temperature pad.
IMPORTANT: To stop the tumbler at any time
during the cycle, OPEN DOOR. To restart the
tumbler, CLOSE door and press START pad.
4. When the cycle is complete, open door and
remove the laundry.
2. Insert card into opening. DO NOT remove the
card until “REMOVE CARD” LED is lit.
3. Press START pad to start tumbler.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Notes
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Maintenance
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
Daily
1. Inspect the area surrounding tumblers, remove all
combustible materials, including lint, before
operating the machines.
2. Check cylinder for foreign objects to avoid
damage to clothing and equipment.
3. Clean lint from lint compartment and screen to
maintain proper airflow and avoid overheating.
WARNING
To reduce the risk of serious injury, do not
open the lint panel while the tumbler is in
operation. Before cleaning the lint screen,
open tumbler door and allow cylinder to
completely stop.
W410
a. Open the lint panel or pull out lint drawer.
c. Be sure the lint screen is not torn. If it is,
replace immediately. A torn lint screen allows
lint to pass from the tumbler to the ductwork
system, thus creating a restriction to air
circulation.
d. The lint screen is designed to completely
cover the entire opening in the lint screen
panel. Be sure that it does so. Excessive gaps
between the lint screen and the lint screen
panel allow lint to pass into the ductwork
system.
e. Carefully wipe any accumulated lint off of the
cabinet high limit thermostat and thermistor.
Failure to do so will allow a buildup of lint in
this area to act as an insulator, causing the
tumbler to overheat. Refer to Figure 12.
f. Replace the lint compartment panel on the
tumbler ensuring a tight fit, and lock if
applicable.
b. Remove all accumulated lint in the lint
compartment area. Lightly brush any lint that
may be left on the lint screen. Lint left in the
lint compartment is drawn back onto the lint
screen and will restrict proper air circulation.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Maintenance
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
2
TMB2121N
1
3
TMB2121N
4
TMB2116N
T30
25, 30 AND 35 POUND
1
2
3
TMB2116N
5
Lint Screen
Guard
Cabinet Thermostat
4
5
Thermistor
Blower Housing
Figure 12
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Maintenance
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
Monthly
Bi-Annually
1. Remove lint and debris from inside exhaust duct
to maintain proper airflow and avoid
overheating.
1. Check mounting hardware for any loose nuts,
bolts or screws.
2. Check gas connections for leakage.
a. Remove external duct and duct access covers,
if present.
3. Check for loose electrical connections.
b. Clean inside of duct with a vacuum.
4. Check steam connections for looseness and
leakage.
c. Clean dampers and make sure they operate
freely.
d. Replace duct and all access covers before
returning to operation.
2. Ensure even lint distribution over lint screen,
replace if distribution of lint is uneven to
maintain proper airflow and avoid overheating.
5. Remove all front panels and vacuum, including
coin drop mechanisms.
6. Check cylinder and front panel seals.
7. Inspect cabinet and inner panels for any damage,
replace or repair as needed.
8. Clean burner tubes of any lint buildup.
3. Carefully wipe any accumulated lint off the
cabinet high limit thermostat and thermistor,
including perforated cover. Lint buildup will act
as an insulator, causing machine to overheat.
4. Clean lint and debris buildup from blower to
maintain proper airflow, to avoid overheating and
prevent possible vibration.
Quarterly
1. Use a vacuum to clean air vents on drive motors.
2. Use a vacuum to clean lint from rear limit
thermostat cover.
3. Refer to Service Manual on how to check and
clean steam coils, if applicable.
4. Check flow of combustion and ventilation air.
5. Check belt tension and condition. Replace worn
or cracked belts.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Maintenance
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
Daily Maintenance
Inspect the area surrounding tumblers,
remove all combustible materials,
including lint, before operating the
machine.
Check cylinder for foreign objects to
avoid damage to clothing and
equipment.
Clean lint from lint compartment and
screen to maintain proper airflow and
avoid overheating.
Monthly Maintenance
Remove lint and debris from inside
exhaust duct to maintain proper airflow
and avoid overheating.
Ensure even lint distribution over lint
screen. Replace if distribution of lint is
uneven to maintain proper airflow and
avoid overheating.
Carefully wipe any accumulated lint off
the cabinet high limit thermostat and
thermistor, including perforated cover.
Lint buildup will act as an insulator,
causing machine to overheat.
Clean lint and debris buildup from
blower to maintain proper airflow, to
avoid overheating and prevent possible
vibration.
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Maintenance
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
Quarterly Maintenance
Use a vacuum to clean air vents on
drive motors.
Use a vacuum to clean lint from rear
limit thermostat cover.
Refer to Service Manual on how to
check and clean steam coils.
Check flow of combustion and
ventilation air.
Check belt tension and condition.
Replace worn or cracked belts.
Bi-Annually Maintenance
Check mounting hardware for any
loose nuts, bolts or screws.
Check gas connections for leakage.
Check for loose electrical connections.
Check steam connections for looseness
and leakage.
Remove all front panels and vacuum,
including coin drop mechanisms.
Check cylinder and front panel seals.
Inspect cabinet and inner panels for any
damage, replace or repair as needed.
Clean burner tubes of any lint buildup.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Notes
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
70269501
Before You Call for Service
Won’t
Start
Won’t
Heat
Clothes
Not Dry
Possible Reason – Corrective Actions
•
Insert correct coin(s) or valid card if applicable.
•
Close the loading door tightly.
•
Close lint panel tightly.
•
Press the PUSH TO START button.
•
Be sure power cord is plugged all the way into the electrical outlet.
•
Drying timer is in OFF position.
•
Check the main fuse and circuit breaker.
•
Check fuses located in the machine.
•
Insufficient airflow.
•
Gas shut-off valve in OFF position.
•
Are controls properly set?
•
Broken drive belt. Call the service person.
•
•
Tumbler is in Cool Down Mode.
•
•
Lint screen clogged. Clean lint screen.
•
•
Exhaust duct to outside is blocked. Clean out.
Customer Service
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
For technical assistance, call (920) 748-3121.
70269501
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27