Operating instructions | Alliance Laundry Systems BF50PV Washer User Manual

Operation/Maintenance
Washer-Extractors
Cabinet Hardmount
B-Series Microcomputer for OPL Models
2 Speed and Variable-Speed
Refer to Page 5 for Model Identification
NOTA: El manual en
español aparece después
del manual en inglés.
CHM166C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. F232219R1
November 2005
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
3
3
3
Introduction.........................................................................................
Model Identification .............................................................................
Introduction...........................................................................................
Electronic Control Unit.........................................................................
Control Output Fuse Board...................................................................
Harnessing........................................................................................
Nameplate Location..............................................................................
Replacement Parts ................................................................................
Customer Service..................................................................................
Summary of Control Outputs and Inputs..............................................
Outputs .............................................................................................
Inputs................................................................................................
Control Voltage................................................................................
5
5
5
5
6
6
7
7
7
7
7
7
7
Operation............................................................................................. 9
Control Panel ........................................................................................ 9
Summary of Major Features ................................................................. 10
Display Indicators................................................................................. 11
Operating Instructions .......................................................................... 13
Maintenance ........................................................................................
Daily .....................................................................................................
Beginning of Day .............................................................................
End of Day .......................................................................................
Weekly..................................................................................................
Monthly.................................................................................................
Quarterly ...............................................................................................
Care of Stainless Steel ..........................................................................
15
15
15
15
16
16
19
20
© Copyright 2005, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Notes
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer and those maintaining the
machine.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas is
flammable; do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power source.
13. Use washer only for its intended purpose,
washing textiles.
14. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
15. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
16. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc. or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
17. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
18. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a qualified
service person.
4
19. Replace worn power cords and/or loose plugs.
20. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
21. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT
bypass the loading door switch by permitting the
washer to operate with the loading door open.
22. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
23. Always follow the fabric care instructions
supplied by the textile manufacturer.
24. Never operate the washer with any guards
and/or panels removed.
25. DO NOT operate the washer with missing or
broken parts.
26. DO NOT bypass any safety devices.
27. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Introduction
Model Identification
Information in this manual is applicable to these models:
HC20BN2
HC50BN2
HC80BNV
SC40BN2
SC60BNF
UC30BN2
UC60BN2
HC30BN2
HC60BN2
SC20BN2
SC50BN2
SC80BNV
UC40BN2
UC60BNF
HC40BN2
HC60BNF
SC30BN2
SC60BN2
UC20BN2
UC50BN2
UC80BNV
Introduction
Electronic Control Unit
The “B” electronic control is composed of the
electronic control unit and the control fuse board with
wiring harness. Only an authorized person should look
inside the machine. First TURN OFF POWER, open
lid and remove any cover present. Make sure door lock
circuit has fully discharged. The door unlock capacitor
can retain high electrical charge, even when the
machine’s electrical inputs are disconnected, until it
has discharged. Some machines are equipped with an
“amber” indicator light facing upward in the control
compartment. If this is on, wait until it goes off
(indicating when high voltage in the door lock circuit
has discharged).
This portion of the control contains the “intelligence” –
the micro-controller and the miscellaneous components
on the printed circuit (PC) board. The board has a
metal cover, which MUST be in place at all times
during machine operation. Operation of the machine
without this cover installed will void the warranty.
F232219
The control unit monitors and responds to input, gives
information about the status of the washer and
monitors and responds to inputs from the user
interface (keypad). The control provides signals to the
control output unit, which in turn operates the
components that control the machine functions. This is
located behind the machine control panel.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Introduction
Control Output Fuse Board
This portion of the control contains the power supply
for the control unit, and also the switching devices
which power the components in the machine, all of
which are on the output PC board. The switching
devices are controlled by the control unit, and are solid
state.
Harnessing
Wiring harnesses are modular – harnesses common to
various configurations are similar, while those specific
to a certain configuration can be added. There are
harnesses for inputs to the control unit, for outputs
from the control power/output unit to the machine
components, and for the main incoming power to the
control power/output unit.
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Introduction
Nameplate Location
The nameplate is located at the rear of the machine and
inside door. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance.
Summary of Control Outputs and
Inputs
Outputs
General outputs provide signals to operate the
following components.
1. Hot Fill Valve
1
2. Cold Fill Valve
3. Drain Valve (normally open)
4. Door Lock Solenoid Coil
5. Door Unlock Solenoid Coil
6. Supply 1 (detergent)
7. Supply 2 (bleach)
8. Supply 3 (sour/softener)
9. Supply 4
10. Supply 5 or Optional 3rd (auxiliary) Fill Inlet
(governed by the configuration settings)
11. Optional Heat
For standard models, the components for outputs
shown as “optional” will not be populated on the
output printed circuit board.
C CHM2060N
1
Nameplate
Figure 1
Replacement Parts
AC outputs are solid state outputs that operate either
120 Volt AC or 220 Volt AC (nominal voltage)
components, depending on the control voltage
configuration. Outputs are fused appropriately.
Inputs
If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
1. Low Water Level
Customer Service
5. Temperature Signal (only for machines with heat
option)
For technical assistance, call: (920) 748-3121 Ripon,
Wisconsin.
2. Medium Water Level
3. High Water Level
4. Door
Control Voltage
The control power supply can be configured to operate
on 110 Volt AC nominal RMS input voltage
50/60 Hertz, OR 220 Volt AC nominal RMS input
voltage 50/60 Hertz.
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Introduction
Model Number Familiarization Guide
Sample Model Number: *C60BN2OU60001
*C
Model Number Prefix
60
Washer-Extractor Capacity (pounds dry weight of laundry)
B
Type of Electrical Control (B = B - Control)
N
Actuation (N = Non-Coin)
2
Washer-Extractor Speed Capability (2 = 2 speed)
O
Electrical Characteristics
U6
Design Series
0001
Option Identification (varies from machine to machine)
* Denotes Brand
*C60BN2OU60001
00000000000
208 – 240
7
3
60
3
60
N/A
3
18
470
N/A
0
500000
EXAMPLE OF NAMEPLATE
CHM487R
CHM487R
Figure 2
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Operation
Control Panel
16 17 18 19
2
1
16 17 18 19
2
1
5
15
5
15
14
WASH
ADD
BLEACH
13
RINSE
SPIN
12
PERM PRESS
HOT
HOT
LIGHT SOIL
VISA TM
HOT
WARM
HEAVY SOIL
UNIFORMS
CLEAN
FILTER
HOT
HOT
3
HOT
COLD
7
13
8
95C
60C
60C
40C
40C
7
8
30C
10
9
3
4
CHM1764C
INTERNATIONAL MODELS
CHM522N
CHM522N
1
2
3
4
5
6
7
8
9
10
6
11
4
DOMESTIC MODELS
95C
<
9
DELICATE
14
<
10
STAINED
6
12
START
DOOR
11
NORMAL
Cycle 1
Cycle 2
Cycle 3
Cycle 4/Up Edit
Cycle 5
Cycle 6
Cycle 7 / Set Up (*) Keypad †
Cycle 8/Down Edit
START Keypad
CLEAN FILTER Indicator LED
(Active for all C80, and C60 X Voltage ONLY
models)
CHM1764C
11
12
13
14
15
16
17
18
19
Door Open LED
Spin Cycle LED
Rinse Cycle LED
Add Bleach LED
Wash Cycle LED
Out-of-Balance Indicator Dot
(Variable-speed only)
High Water Level Indicator Dot
Medium Water Level Indicator Dot
Low Water Level Indicator Dot
Figure 3
†Set Up(*) keypad is used in cycle programming in program mode. Refer to Programming Manual.
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Operation
Summary of Major Features
LED for Machine Functions
LED lights inform operator which machine function is active. DOOR LED lights to
inform operator that the door can be opened or should be closed. The circle LED
indicates that the filter needs cleaning.
Water Levels
Three (3) – Contacts from pressure switch (test cycle)
Main LED display
4 digit LED display counts down cycle time. Lights in LED display indicate out-of-balance
conditions and, in test cycle, water level. Display shows “01” as the final spin time.
Cycle selection keypads
Eight (8) cycle select keypads with LED indicator to show selected cycle. LED lights
will flash to prompt user to press a keypad.
START keypad
Press to start a cycle after cycle selection is made. LED light will flash to prompt user to
press keypad.
Test Cycle with “Advance”
For troubleshooting. Advance rapidly through test cycle by pressing the UP keypad.
Refer to PROGRAMMING manual.
Fill Temperatures
Cold, Hot, Warm
Supplies
Five (5) or Four (4) with extra fill value option.
Agitation Types
Normal or Gentle
Drain Options
Normally open gravity drain
Cycle Count
0 to 9999 cannot be reset – Rolls over after 9999
Rapid Advance Mode
Rapid Advance can be enabled or disabled. Enabled allows user to advance through a
cycle. Refer to the Programming Manual.
Table 1
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Operation
Display Indicators
Table 2 lists the various displays and what they
mean. The operator should become familiar with
these machine displays.
Display
Meaning
tESt
Diagnostic test cycle selected or enabled
SPIn
Spin (extract) step
SUP1
Supply signal 1 (“S1” output), normally detergent
SUP2
Supply signal 2 (“S2” output), normally bleach
SUP3
Supply signal 3 (“S3” output), normally softener
SUP4
Supply signal 4
SUP5
Supply signal 5
SdLY
Spin coast (motor coasts after high speed extract)
CFIL
Cold Fill
HFIL
Hot Fill
bFIL
Warm Fill (cold + hot)
bLCH
Control will also light “add bleach” indicator
PASS
Variable-speed ONLY – balance “PASS” condition; shows in “test” cycle only
FAIL
Variable-speed ONLY – balance “FAIL” condition; shows in “test” cycle only
bAL?
Variable-speed ONLY – meaning: “Do you wish to enter balance detection test routine?”
CY__
Cycle number (followed by a space and number 1 through highest cycle number)
norn
Normal agitation selected
gEnt
Gentle (reduced) agitation selected
SPn1
Variable-speed ONLY – low spin speed (the lower of 2 spin speeds)
SPn2
Variable-speed ONLY – high spin speed (the higher of 2 spin speeds)
For
Wash speed forward (during test cycle)
rEv
Wash speed reverse (during test cycle)
dISt
Variable-speed ONLY – distribution speed (during test cycle)
LO
Low water level
nEd
Medium water level
HI
High water level
CEL
Display all temperatures in degrees Celsius
FAr
Display all temperatures in degrees Fahrenheit
___C
The first 3 digits are reserved for temperature reading, C indicates “degrees Celsius”
Table 2 (Continued)
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Operation
Table 2 (Continued)
Display
12
Meaning
___F
The first 3 digits are reserved for temperature reading, F indicates “degrees Fahrenheit”
FILL
“Fill error” – machine did not fill to programmed water level within 10 minutes; also
displays during Rapid Advance Mode.
door
“Door” opened during cycle
SHUt /door
Machine user must “shut door” of the washer to allow the cycle to begin
CAnt /OPEn
Control cannot unlock the door
USH1
“Wash 1” segment
USH2
“Wash 2” segment
USH3
“Wash 3” segment
USH4
“Wash 4” segment
rIn1
“Rinse 1” segment
rIn2
“Rinse 2” segment
rIn3
“Rinse 3” segment
rIn4
“Rinse 4” segment (final rinse)
donE
Cycle has concluded
drAI
Drain selected for segment; also indicates in drain step during 2 speed version test cycle or
during Rapid Advance Mode.
----
Flashes for a period of time (for safety) after power up while keeping outputs OFF
Adv
Machine set up for Rapid Advance
noAd
Machine is not set up for Radid Advance
Erdn
Drain count error (depending on model)
Erfl
Fill error count (depending on model)
E Pr
The number of times power has been interrupted during a cycle (will display in certain
models)
CyC
Cycle counter
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Operation
Operating Instructions
1. Turn on main power source (circuit breaker) with
right hand.
5. Close door and turn handle counterclockwise
until button pops out. Refer to Figure 6.
2. With left hand, push and hold white rocker
button. Refer to Figure 4.
3. Push button and turn handle clockwise to open.
Refer to Figure 4.
U005I
U005I
Figure 6
6. The default wash cycle will display.
NOTE: Perm Press Hot is the default cycle if none
is selected.
CHM2027N
Figure 4
4. Load to capacity whenever possible. DO NOT
OVERLOAD. Refer to Figure 5.
NORMAL
WASH
ADD
BLEACH
NOTE: Underloading can cause out-of-balance
conditions that can shorten machine life.
HOT
LIGHT SOIL
VISA TM
RINSE
SPIN
DOOR
PERM PRESS
HOT
HOT
WARM
HEAVY SOIL
UNIFORMS
START
CLEAN
FILTER
HOT
HOT
STAINED
DELICATE
HOT
COLD
DOMESTIC MODELS
CHM522N
95C
95C
60C
60C
40C
40C
U003I
Figure 5
30C
<
<
INTERNATIONAL MODELS
CHM1764C
CHM1764C
Figure 7
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Operation
7. If desired, select a different cycle at this point.
The LED indicator for that cycle will light.
8. Add liquid and/or powder supplies to supply
dispenser. Refer to Figure 8.
9. When applicable, add bleach to compartment 2
when the ADD BLEACH LED is lit.
10. Press the desired wash cycle keypad if none is
selected.
a. Add detergent to compartment 1.
11. Press the START keypad.
b. Add softener to compartment 3.
12. During first fill, the desired wash cycle can be
changed. After first fill has ended, the wash cycle
active at that moment remains the chosen wash
cycle.
13. When cycle is complete, display shows “donE”.
3
1
2
CHM486R
CHM486R
1
2
3
Detergent
Bleach
Softener
Figure 8
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Maintenance
4. Check door interlock before starting operation:
WARNING
Sharp edges can cause personal injury.
Wear safety glasses and gloves, use
proper tools and provide lighting when
handling sheet metal parts.
W366R1
IMPORTANT: Replace all panels that are removed
to perform service and maintenance procedures.
Do not operate the machine with missing guards or
with broken or missing parts. Do not bypass any
safety devices.
Daily
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door, and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
End of Day
IMPORTANT: Door lock should be checked daily
to ensure proper operation. Also check that all
safety and instruction stickers are on the machine.
Any missing or illegible safety instructions stickers
should be replaced immediately.
Beginning of Day
1. Clean the door gasket of residual detergent and
all foreign matter.
2. Clean automatic supply dispenser lid and general
area. Flush dispenser with clean water.
3. Clean the machine’s top, front and side panels
with mild detergent. Rinse with clean water.
1. Inspect water inlet valve hose connections on the
back of the machine for leaks.
4. Leave loading door open at the end of each day to
allow moisture to evaporate.
2. Inspect steam hose connections for leaks (where
applicable).
NOTE: Unload the machine promptly after each
completed cycle to prevent moisture buildup. Leave
loading door open after each completed cycle to
allow moisture to evaporate.
3. Verify that insulation is intact on all external
wires and that all connections are secure. If
exposed wire is evident, call a service technician.
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Maintenance
Weekly
Monthly
1. For variable-speed models only, clean the AC
drive box filter(s) weekly or more frequently as
needed:
NOTE: If fan filter service indicator light is on, fan
filter must be cleaned immediately to prevent
possible damage. Thermostat automatically resets
after drive compartment cools down. LED will then
extinguish after cycle run.
IMPORTANT: If filter indicator is ignored,
repeated resets might shorten life of drive. Clean
filter regularly to avoid indicator prompt.
a. Open the top cover.
NOTE: Disconnect power to the machine at its
source before performing the monthly maintenance
procedures.
1. Use the following procedures to determine if
V-belt(s) require replacement or adjustment. Call
a qualified service technician in either case.
a. Check V-belt(s) for uneven wear and frayed
edges.
b. Verify pulley alignment by placing a
straightedge across both pulley faces. The
straightedge should make contact with the
pulleys in four places. Refer to Figure 9.
b. Grasp the filter handle and pull straight up to
remove filter.
1
c. Wash the filter with warm water and allow
filter to air-dry. As an alternative, the filter
may be vacuumed clean.
4
IMPORTANT: The control module cover and fan
filter must be in place for the fan to properly cool
the AC inverter drive. Failure to observe this
warning will void the warranty and could lead to
expensive AC inverter drive repair.
2
3
H040I
H040I
2. Check the machine for leaks.
a. Start an unloaded cycle to fill the machine.
b. Verify that door and door gasket do not leak.
c. Verify that the drain valve is operating and
that the drain system is free from obstruction.
If water does not leak out during the first wash
segment, the drain valve is closed and
functioning properly.
16
1
2
3
4
Motor
Motor Pulley
Straightedge
Basket Pulley
Figure 9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Maintenance
c. For flat-pulley drive systems, verify allowable
distance of belt from edge of pulley. Refer to
Table 3 below.
Flat-Pulley Alignment
Model
Allowable
Distance from Edge
20
3/32 in. (2 mm)
25
3/32 in. (2 mm)
30
3/32 in. (2 mm)
40
3/32 in. (2 mm)
50 – 60
3/8 in. (10 mm)
1
2
H039I
1
2
Table 3
Deflection
Span Length
d. For variable-speed models only, verify that
V-belts are properly tensioned by applying a
set force to the belts and measuring the
deflection to determine the belt tension. Refer
to Table 4 for the acceptable belt’s tension
ranges. Belt tension measurements should be
taken as close to the center of the belt span as
possible. Refer to Figure 10.
Figure 10
Belt Tension Testing for Variable-Speed Models
Model
Belt
Belt Span
Deflection Range
Force
Min – Max
35, 40
Motor-Basket
16.9 in. (428 mm)
5/16 – 11/32 in. (7.9 – 8.7 mm)
6.1 – 7.4 lbs. (27 – 33 N)
50, 60
Motor-Basket
16.8 in. (426 mm)
9/32 – 5/16 in. (7.1 – 7.9 mm)
6.1 – 7.4 lbs. (27 – 33 N)
80
Motor-Basket
Single Belt
22.1 in. (561 mm)
15/32 – 1/2 in. (11.9 – 12.7 mm)
4.9 – 7.3 lbs. (21.8 – 31.5 N)
80
Motor-Basket
Banded Belt
22.1 in. (561 mm)
7/32 – 1/4 in. (5.08 – 6.35 mm)
23 – 26 lbs. (102.3 – 115.6 N)
Table 4
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Maintenance
1
2
H047I
H047I
1
2
Bearing Grease Fitting
Seal Grease Fitting
Figure 11
2. For 80 pound capacity models only, lubricate
bearings and seals each month OR after every
200 hours of operation. Refer to Figure 11.
a. Use a premium-grade lithium-based #2
grease. Never mix two types of grease, such
as petroleum and silicone.
18
b. Pump the grease gun slowly, permitting only
the following number of strokes:
●
Bearing grease fitting, 2 strokes
●
Seal grease fitting, 1 stroke
Do not pump the grease gun until grease
comes out of the bearing housing. This can
result in overlubrication, causing damage to
bearings and seals.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Maintenance
3. Remove back panel and check overflow hose and
drain hose for leaks.
4. Unlock the hinged lid and check the supply
dispenser hoses and hose connections.
4. Check all painted surfaces for exposed metal.
(Matching paint is available from the
manufacturer.)
●
If bare metal is showing, paint with primer or
solvent-based paint.
●
If rust appears, remove it with sandpaper or by
chemical means.
5. Clean inlet hose filter screens:
a. Turn water off and allow valve to cool, if
necessary.
Then paint with primer or solvent-based paint.
b. Unscrew inlet hose and remove filter screen.
c. Clean with soapy water and reinstall. Replace
if worn or damaged.
6. Tighten motor mounting bolt locknuts and
bearing bolt locknuts, if necessary.
7. Use compressed air to clean lint from motor.
8. Clean interior of machine, both basket and shell,
by wiping with a water-soaked sponge or cloth.
5. Clean customer-supplied steam filter, where
applicable. Refer to Figure 12.
a. Turn off steam supply and allow time for the
valve to cool.
b. Unscrew cap.
c. Remove element and clean.
d. Replace element and cap.
9. Use compressed air to ensure that all electrical
components are free of moisture and dust.
10. For variable-speed models only, clean AC drive
cooling fan blades monthly (more often if
required by the condition of the air).
a. Open the top cover and remove the control
module cover.
1
b. Gently wipe the fan blades clean with a dry
cloth.
2
Quarterly
NOTE: Disconnect power to the machine before
performing the quarterly maintenance procedures.
1. Tighten door hinges and fasteners, if necessary.
H042I
2. Tighten anchor bolts, if necessary.
3. Verify that the drain motor shield is in place and
secure, if so equipped.
H042I
1
2
Cap
Filter Element
Figure 12
F232219
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Maintenance
Care of Stainless Steel
●
Remove dirt and grease with detergent and water.
Thoroughly rinse and dry after washing.
●
Avoid contact with dissimilar metals to prevent
galvanic corrosion when salty or acidic solutions
are present.
●
Do not allow salty or acidic solutions to
evaporate and dry on stainless steel. Wipe clean
of any residues.
●
Do not leave sanitizers or sterilizing solutions on
stainless steel equipment for prolonged periods
of time.
20
●
When an external chemical supply is used, ensure
no siphoning of chemicals occurs when the
washer-extractor is not in use. Highly
concentrated chemicals can cause severe damage
to stainless steel and other components with the
machine. Damage of this kind is not covered by
the manufacturer’s warranty. Locate the pump
below the washer-extractor’s injection point to
prevent siphoning of chemicals into the machine.
●
If the stainless steel appears to be rusting, the
source of the rust may actually be a foreign piece
of iron or steel part not made of stainless steel,
such as a nail or screw contacting the stainless
steel surface. Tip: Paint all carbon steel parts with
a heavy protective coating. Stainless steel
fasteners should be used whenever possible.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232219
Download PDF

advertising