Specifications | Alliance Laundry Systems BF85PV Washer User Manual

For Your Records and Warranty
Assistance
Model Name: ______________________
Catalog/Model No.: _________________
installation and
operation manual
for Hunter
Ceiling Fans
Serial No.: ________________________
Date Purchased: ____________________
Where Purchased: _ _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
TYPE 2 Models
45006-01 • 09/26/07
90% Pre-Assembled Out Of The Box!
Makes Installation Fast in 3 Easy Steps
1. Install mounting bracket and make wiring connections
2. Attach EasyLockTM Blades
3. Install bulb(s) and glass
Installation is complete!
Please follow the detailed installation instructions inside this manual
45006-01 • 09/26/07 • Hunter Fan Company
Welcome
Your new Hunter® ceiling fan is an addition to your home or office that
will provide comfort and performance for many years. This installation
and operation manual gives you complete instructions for installing
and operating your fan.
The Hunter 5-Minute Fan can be
installed by most users in 5 minutes
or less!
*5 Minute time interval
does not include Section 2:
Installing the Ceiling Plate
Table of Contents
1 • Getting Ready . . . . . . . . . . . . . . . . . . . . . . . 4
2 • Installing the Hanger Bracket . . . . . . . . . 5
3 • Assembling and Hanging the Fan . . . . . 6
4 •Wiring the Fan . . . . . . . . . . . . . . . . . . . . . . . 8
5 • Installing the Canopy and Canopy Trim Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6 • Assembling the Blades . . . . . . . . . . . . . . 10
7 • Completing Your Installation With or Without a Bowl Light Fixture . . . . 11
8 • Operating and Cleaning Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . 13
9 • Troubleshooting . . . . . . . . . . . . . . . . . . . . 14
We are proud of our work. We appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.
Before installing your fan, for your records and warranty assistance,
record information from the carton and Hunter nameplate label
(located on the top of the fan motor housing).
Cautions and Warnings
• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions,
and use only the hardware supplied.
• To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
• To reduce the risk of personal injury, do not bend the blade
attachment system when installing, balancing, or cleaning the fan.
Never insert foreign objects between rotating fan blades.
• To reduce the risk of fire, electrical shock, or motor damage, do not
use a solid-state speed control with this fan. Use only Hunter speed
controls.
© 2007 Hunter Fan Company
2
45006-01 • 09/26/07 • Hunter Fan Company
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Support Brace
Standard
Mounting
Style
Ceiling
Outlet Box
Hunter’s patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Profile, Standard, or Angle mounting. The steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
Standard Mounting hangs from the
ceiling by a downrod (included).
For ceilings higher than 8 feet, you can purchase
Hunter extension downrods. All Hunter fans use
sturdy 3/4” diameter pipe to assure stability and
wobble-free performance.
Support Brace
Ceiling
Outlet Box
Support Brace
8
Angle
Mounting
Style
12
Low Profile
Mounting
Style
Angle Mounting recommended for a
vaulted or angled ceiling
Ceiling
Outlet Box
Low Profile Mounting fits close to the
ceiling, recommended for ceilings less
than 8 feet high
3
45006-01 • 09/26/07 • Hunter Fan Company
CAUTION: To
reduce the risk of
personal injury, attach
the fan directly to the
support structure of
the building according
to these instructions,
and use only the
hardware supplied.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
Installing Multiple Fans?
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
4
45006-01 • 09/26/07 • Hunter Fan Company
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. The pilot holes should be 9/64”
in diameter.
Install Bracket & Wiring
2 • Installing the Hanger Bracket
Isolator
Hanger
Bracket
Note: Your fan comes with four pre-installed neoprene noise
isolators.
2-2. Thread the lead wires from the outlet box down through the hole
in the middle of the hanger bracket.
2-3. Align the slotted holes in the hanger bracket with the pilot holes
you drilled in the wood support structure. For proper alignment
use slotted holes directly across from each other. If you are
installing the fan on an ANGLED ceiling, be sure to orient the
hanger bracket as shown in Illustration 2-3 (left or right view).
Note: The isolators should be flush against the ceiling.
2-4. Place a flat washer on each of the two 3” screws and pass the
screws through the slotted holes in the hanger bracket into the
pilot holes you drilled.
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Flat Washer
Steps 2-2 – 2-4
Large
Opening
Ceiling Peak
or
Ceiling Peak
Large
Opening
3” Screw
Left
Step 2-3 (Angled Ceiling Only)
5
45006-01 • 09/26/07 • Hunter Fan Company
RIGHT
You can assemble your fan for standard or angle mounting as shown
in steps 3-1 – 3-3. For low profile mounting (ceilings less than 8 feet
high), go to steps 3-6 – 3-9 on the next page.
3-1. To assemble fan to hang down from a flat or angled ceiling, place
the canopy and canopy trim ring around the adapter so that they
rest on the fan assembly.
3-2. Feed the wires from the fan through the downrod.
Note: Make sure all the wires are on the same side of the metal
dowel pin inside the dowrod.
3-3. Loosen the square head set screw on the adapter to install the
pipe and ball assembly. Note: When the pipe and ball assembly
is fully installed, 2-3 threads on the pipe will still be visible; this is
normal. Securely retighten the set screw with a wrench or pliers.
Downrod
Canopy
(with Washer)
Adapter
Canopy
Trim
Ring
Set Screw
CAUTION: The adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
WARNING: Do not carry or lift fan by canopy.
3-4. Raise the fan and place the ball into the hanger bracket.
3-5. Align the notch on the ball with the indent in the hanger bracket.
(Rotate the fan until you hear the notch pop into place.)
Go to 4 • Wiring the Fan.
Steps 3-1 – 3-3
Indent
Steps 3-4 – 3-5
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
6
45006-01 • 09/26/07 • Hunter Fan Company
Install Bracket & Wiring
3 • Assembling and Hanging the Fan
Install Bracket & Wiring
3 • Assembling and Hanging the Fan (Low Profile Only)
You can assemble your fan for standard or angle mounting as shown
in steps 3-1 – 3-3 on the previous page. For low profile mounting
(ceilings less than 8 feet high), see steps 3-6 – 3-10 on this page.
3-6. Remove the screws from the hanger ball bracket.
3-7. Place the low profile washer from the parts sack into the canopy.
3-8. Place the canopy trim ring and canopy with washer on top of the
fan assembly.
3-9. Align the screw holes in the washer with the holes in the adapter. Assemble securely with three #8-32 x 1/2” screws.
3-10. Raise the fan and place the hook on the hanger bracket through
the round hole in the rim of the canopy.
Step 3-6
(Not Actual Size)
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Steps 3-8 – 3-9
Low Profile Washer
Step 3-7 (Detail)
Low Profile Washer
Adapter
Canopy
Trim Ring
#8-32 x 1/2” Screw
Step 3-10
7
45006-01 • 09/26/07 • Hunter Fan Company
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch
in accordance with national and local electrical codes.
4-1. Before attempting installation, make sure the power is still off.
4-2. To connect the wires, hold the bare metal leads together and place
a wire nut over them, then twist clockwise until tight. For all these
connections use the wire connectors provided.
4-3. Connect the bare or green ground wire (grounded) from the
ceiling to the green ground wire (grounded) from the ceiling plate
and the green ground wire from the fan.
4-4. Connect the white wire (ungrounded) from the ceiling to the
white wire (ungrounded) from the fan.
4-5. Connect the remaining wires as follows:
Dual Switch Wiring:
• The black wire (ungrounded) from the ceiling to the black wire
(ungrounded) from the fan
• The black/white wire (ungrounded) from the fan to the wire
(ungrounded) for the wall switch
Single Switch Wiring:
• The black wire (ungrounded) from the ceiling to the black
(ungrounded) and the black/white wire (ungrounded) from
the fan
Install Bracket & Wiring
4 •Wiring the Fan
Wire
Connector
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
4-6. Turn the wire connectors upward and push them carefully back
through the ceiling plate into the outlet box.
4-7. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the
outlet box.
8
45006-01 • 09/26/07 • Hunter Fan Company
5-1. Partially install two canopy screws (about 2 full turns) in the
hanger bracket.
Steps 5-1 – 5-2
Hanger Bracket
5-2. Raise the canopy over the hanger bracket. Align partially installed
screws with key slots in canopy.
5-3. Twist canopy clockwise to secure.
5-4. Install third & fourth canopy screw in round hole on canopy.
Securely tighten all four screws.
5-5. Using both hands, push the canopy trim ring up to the top of the
canopy.
Canopy
Canopy Trim
Ring
5-6. Twist canopy trim ring clockwise to secure the canopy.
Should you need to remove the canopy
trim ring, follow these steps:
1. Twist canopy trim ring counter
clockwise until it releases from
canopy.
Step 5-3
Step 5-4
Step 5-5
Canopy
Screw
9
45006-01 • 09/26/07 • Hunter Fan Company
Install Bracket & Wiring
5 • Installing the Canopy and Canopy Trim Ring
6 • Assembling the Blades
Our exclusive Easy Lock™ blade assembly enables you to lock the blades
in place without tools and to remove the blades easily for cleaning.
6-1. Open the locking mechanism.
6-2. Align the holes in the blade with the blade iron.
6-3. Close the locking mechanism securely. You will feel it lock into
place.
6-4. Repeat steps 6-1 through 6-3 until all blades are installed.
TM
Step 6-1
Attach EasyLock Blades
Open
Close
Step 6-3
10
45006-01 • 09/26/07 • Hunter Fan Company
7 • Completing Your Installation With or Without a Bowl Light Fixture
Installing the Glass Bowl
7-1. If you want to install the light fixture,
proceed with Step 7-2 now.
Step 7-3
If you do not want to install the light
fixture, you need to uninstall it now. See
“Uninstalling the Light Fixture” in Step
7-7. Once you have uninstalled the light
fixture, continue with step 7-2.
7-2. Attach the extra pull chain (included)
to the fan pull chain using the plastic
breakaway connector. (You may find the
plastic breakaway connector on the end
of the extra chain.)
Light Bulb
(Pin Base CFL)
Fan
Pull Chain
Light
Pull Chain
Grommet Hole
(Metal Disk)
7-3. Feed the fan and light pull chains as
shown in Step 7-3 illustration.
7-4. Install the Pin Base CFL (26 Watt
Maximum) into the socket.
Fan
Pull Chain
7-6. Screw the finial onto the threaded rod end
until tight.
Hole (Cover Plate)
Go to 8 • Operating and Cleaning the Fan.
Breakaway
Connector
11
45006-01 • 09/26/07 • Hunter Fan Company
Light
Pull Chain
Finial
Install Bulb(s)
bulb(s) & Glass
7-5. Place the cover plate up against the glass
bowl. Align the holes in the cover plate
with the grommet hole of the metal disk.
7 • Completing Your Installation With or Without a Bowl Light Fixture (Continued)
Uninstalling the Light Fixture
7-7. Remove the lower switch housing screws, then remove the lower
switch housing.
Lower Switch
Housing
7-8. To uninstall the light fixture, disconnect the 9-pin plug connectors.
7-9. You must remove the wiring harness and its components from the
integrated light fixture. You must then install the wiring harness
into the empty switch housing included with the fan.
Lower Switch
Housing
Screw
7-10. Locate the reversing switch and carefully remove the two screws
holding the reversing switch to the lower switch housing. Then,
remove the reversing switch from the housing.
7-11. Remove the patented breakaway connector from the end of the
fan pull chain. Carefully loosen the bellmouth nut from the pull
chain and remove the pull chain switch from the light fixture
housing.
Bracket
Assembly
Screws
7-12. Locate and carefully remove the two capacitors.
7-13. Unplug the two-pin wire connector with one white wire and
a black with white striped wire coming from the multi-wire
connector.
Steps 7-7 – 7-14
7-15. Insert the pull chain and fan pull chain switch through the round
opening on the side of the empty switch housing. Thread the
bellmouth nut over the pull chain and hand tighten the bellmouth
nut.
7-16. Reattach the breakaway connector to the pull chain.
Threaded Rod
Switch Housing
Cap
7-17. Insert the reversing switch into the square hole on the side of the
switch housing. Install and tighten the two screws you removed
previously from the other switch housing.
7-18. Carefully place the capacitors in the switch housing.
7-13. Install the switch housing cap and plug button to the lower switch
housing.
7-14. Re-attach the 9-pin plug and reinstall the lower switch housing
screws.
7-15. Once you have uninstalled the light fixture, continue with step 8‑1.
12
45006-01 • 09/26/07 • Hunter Fan Company
Step 7-15 – 7-16
Plug Button
Install bulb(s) & Glass
7-14. You have now disconnected the wiring harness and its
components and are ready to install them into the empty switch
housing. (The light switch remains in the light assembly housing.)
8 • Operating and Cleaning Your Ceiling Fan
8-1. Turn on electrical power to the fan.
8-2. The fan pull chain controls power to the fan. The pull chain has
four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• The chain uses a breakaway connector that separates if the
chain is jerked. If this happens, simply reinsert the chain into
the connector.
8-3. Ceiling fans work best by blowing air downward (counterclockwise
blade rotation) in warm weather to cool the room with a direct
breeze. In winter, having the fan draw air upward (clockwise blade
rotation) will distribute the warmer air trapped at the ceiling
around the room without causing a draft.
In warm weather, use
downward air flow pattern
8-4. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust using
a mild detergent and a slightly dampened cloth. You may use
an artistic agent, but never abrasive cleaning agents as they will
damage the finish.
8-5. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in the
same manner as the fan finish.
In cold weather, use upward
air flow pattern
To Change Airflow Direction
Turn the fan off and let it come to a complete
stop. Slide the reversing switch on the fan to the
opposite position. Restart fan.
Reversing
Switch
13
45006-01 • 09/26/07 • Hunter Fan Company
9 • Troubleshooting
Problem: Nothing happens; fan does not move.
1.Turn power on, replace fuse, or reset breaker.
2.Loosen canopy, check all connections according to the wiring the
fan section.
3.Check the plug connection in the switch housing.
4.Push motor reversing switch firmly left or right to ensure that the
switch is engaged.
5.Pull the pull chain to ensure it is on.
6.Remove the shipping bumpers.
Problem: Noisy operation.
1.Tighten the blade bracket screws until snug.
2.Check to see if the blade is cracked. If so, replace all the blades.
Problem: Excessive wobbling.
1.If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2.Tighten all blade iron screws.
3.Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
If you need parts or service assistance, please call
888‑830‑1326 or visit us at our Web site at
http://www.hunterfan.com.
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
14
45006-01 • 09/26/07 • Hunter Fan Company
Hunter fans have the power to cut your cooling costs up to 40%.
Beat the High Cost of Cooling
The air movement created by a Hunter ceiling fan lets you set your
thermostat higher and still stay comfortable. Every degree you
raise the thermostat saves up to 7% on energy costs. So, you can
cut back on expensive air conditioning...and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air and saves
up to 10%* on heating bills.
* On average at low speed settings. Your savings may vary based
on climate, building type and thermostat setting.
Save Energy and Money While Protecting the Environment
Congratulations! You’re saving energy and money while protecting
the environment by purchasing this ENERGY STAR qualified
Hunter ceiling fan! With this purchase, you are doing your part to
protect the environment. In 2010, ENERGY STAR qualified ceiling
fans are projected to cut air pollution by more than 500 million
pounds!
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efficiency specifications set by
the Environmental Protection Agency (EPA). ENERGY STAR
labeled ceiling fans save energy because they have more efficient
fan motors and air delivery due to more aerodynamic blade
configurations. Ceiling fan models bearing the ENERGY STAR label
move air 14 - 20% more efficiently than typical ceiling fan models.
For more information on ENERGY STAR visit www.energystar.gov.
15
45006-01 • 09/26/07 • Hunter Fan Company
Download PDF

advertising