Specifications | Alliance Laundry Systems SW039 Washer User Manual

Installation/Operation Supplement
Washer-Extractors
Cabinet Freestanding
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9001014R5
www.comlaundry.com
July 2008
Installation/Operation Supplement
Table of
Contents
Introduction.........................................................................................
Model Identification .............................................................................
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
Specifications and Dimensions...........................................................
Installation...........................................................................................
Dimensional Clearances...................................................................
Machine Foundation ........................................................................
Mechanical Installation.........................................................................
Frame Dimensions and Mounting Bolt Location for 18, 25,
35, 55, 75, 100, 135 and 165 Models .............................................
Mounting Bolt Installation (If Required)..............................................
Electrical Specifications .......................................................................
Operation.............................................................................................
Control Identification............................................................................
Load the Machine .................................................................................
Disposal of Unit ...................................................................................
2
2
3
3
3
5
6
7
21
21
22
23
23
25
26
27
27
28
29
© Copyright 2008, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Installation/Operation Supplement
Introduction
Model Identification
Information in this manual is applicable to these
models:
2
HX18PV
HX75PV
SX18PV
SX75PV
UX18PV
UX75PV
HX25PV
HX100PV
SX25PV
SX100PV
UX25PV
UX100PV
HX35PV
HX135PV
SX35PV
SX135PV
UX35PV
UX135PV
HX55PV
HX165PV
SX55PV
SX165PV
UX55PV
UX165PV
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas is
flammable, do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Installation/Operation Supplement
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a qualified
service person.
4
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Installation/Operation Supplement
Operator Safety
Do not bypass any safety devices in the machine.
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a.Attempt to start the machine with the door
open. The machine should not start with the
door open.
b.Close the door without locking it and attempt to
start the machine. The machine should not
start with the door unlocked.
c.Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a.The door does not remain securely locked
during the entire cycle.
b.Excessively high water level is evident.
c.Machine is not connected to a properly
grounded circuit.
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
Specifications and Dimensions
General Specifications
Model
18
25
35
660 mm (26 in.)
660 mm (26 in.)
783 mm (30.8 in.)
Overall Dimensions
Overall width
Overall height
1031 mm (40.6 in.) 1031 mm (40.6 in.) 1194 mm (47 in.)
Overall depth
780 mm (30.7 in.)
870 mm (34.3 in.)
960 mm (37.8 in.)
Net weight
236 kg (520 lb.)
241 kg (531 lb.)
347 kg (765 lb.)
Shipping weight
283 kg (624 lb.)
290 kg (639.5 lb.)
467 kg (1030 lb.)
Weight and Shipping Information
3
0.8 m (22.5 ft )
0.9 m (24.5 ft )
1.3 m3 (34.7 ft3)
Cylinder diameter
530 mm (20.9 in.)
530 mm (20.9 in.)
650 mm (25.6 in.)
Cylinder depth
345 mm (13.6 in.)
440 mm (17.3 in.)
500 mm (19.7 in.)
Cylinder volume
76 l (2.7 ft3)
97 l (3.43 ft3)
167 l (5.9 ft3)
Perforation size
3 mm (0.1 in.)
3 mm (0.1 in.)
3 mm (0.1 in.)
300 mm (11.8 in.)
300 mm (11.8 in.)
300 mm (11.8 in.)
279 mm (11 in.)
279 mm (11 in.)
395 mm (15.6 in.)
HOT
90 l (24 gal.)
110 l (29 gal.)
178 l (47 gal.)
COLD
42 l (11 gal.)
49 l (13 gal.)
79 l (21 gal.)
Motor
0.15 kW/hr
0.15 kW/hr
0.2 kW/hr
Heating
1.5 kW/hr
2.25 kW/hr
3.75 kW/hr
Shipping volume
3
3
3
Wash Cylinder Information
Door Opening Information
Door opening size
Height of door bottom above floor
Water Consumption
Average water consumption per cycle
Power Consumption
Average power used per cycle
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Installation/Operation Supplement
General Specifications
Model
18
25
35
1
1
1
0.75 kW (1 hp)
0.75 kW (1 hp)
1.5 kW (2 hp)
10-50 rpm
10-50 rpm
10-50 rpm
82 rpm
82 rpm
74 rpm
250-1000 rpm
250-1000 rpm
250-1000 rpm
0.03-0.74 Gs
0.03-0.74 Gs
0.04-0.91 Gs
19-296 Gs
19-296 Gs
23-363 Gs
Standard
Standard
Standard
10 mm (0.38 in.)
10 mm (0.38 in.)
10 mm (0.38 in.)
1
1
1
LOW
0.83 kg (1.15 lb.)
1.15 kg (1.6 lb.)
1.6 kg (2.22 lb.)
HIGH
0.94 kg (1.3 lb.)
1.3 kg (1.8 lb.)
1.8 kg (2.52 lb.)
7.6 kg (0.48 bhp)
9.5 kg (0.60 bhp)
16.5 kg (1.05 bhp)
9 kW
9 kW
18 kW
Electrical heating elements
3
3
6
Electrical heat element size
3 kW
3 kW
3 kW
10°C
3 minutes
5 minutes
5 minutes
50°F
6 minutes
8 minutes
8 minutes
10°C
4 minutes
6 minutes
6 minutes
50°F
7 minutes
9 minutes
9 minutes
Drive Train Information
Number of motors in drive train
Drive motor power
Cylinder Speeds
Wash/reverse speed
Distribution/drain speed
Extract speed
Centrifugal Force Data
Wash/reverse centrifugal force
Extract centrifugal force
Balance Detection
Vibration safety switch installed
Direct Steam Heating (Optional)
Steam inlet connection size
Number of steam inlets
Steam required to raise
bath temperature 10°C, kg (10°F, lb.)
Average steam use per cycle
Electrical Heating (Optional)
Total electrical heating capacity
Time required to raise bath temperature
LOW
MED
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
General Specifications
Model
55
75
100
135
165
Overall width
900 mm
(35.4 in.)
1060 mm
(41.8 in.)
1200 mm
(47.3 in.)
1200 mm
(47.3 in.)
1300 mm
(51.8 in.)
Overall height
1544 mm
(60.8 in.)
1560 mm
(61.4 in.)
1920 mm
(75.6 in.)
1920 mm
(75.6 in.)
2100 mm
(82.7 in.)
Overall depth
1016 mm
(40 in.)
1168 mm
(46 in.)
1330 mm
(52.4 in.)
1500 mm
(59.1 in.)
1620 mm
(63.8 in.)
Net weight
570 kg
(1247 lb.)
865 kg
(1907 lb.)
1520 kg
(3351 lb.)
1645 kg
(3626 lb.)
2100 kg
(4630 lb.)
Shipping weight
630 kg
(1380 lb.)
995 kg
(2194 lb.)
1697 kg
(3741 lb.)
1822 kg
(4017 lb.)
2319 kg
(5113 lb.)
Shipping volume
1.5 m3
(54.9 ft3)
2.1 m3
(74 ft3)
3.3 m3
(115 ft3)
3.7 m3
(131 ft3)
4.4 m3
(162 ft3)
Cylinder diameter
750 mm
(29.5 in.)
850 mm
(33.5 in.)
980 mm
(38.6 in.)
980 mm
(38.6 in.)
1095 mm
(43.1 in.)
Cylinder depth
530 mm
(20.9 in.)
537 mm
(21.1 in.)
597 mm
(23.5 in.)
775 mm
(30.5 in.)
775 mm
(30.5 in.)
Cylinder volume
234 l
(8.27 ft3)
305 l
(10.76 ft3)
451 l
(15.92 ft3)
585 l
(20.66 ft3)
730 l
(25.8 ft3)
Perforation size
3 mm
(0.1 in.)
3 mm
(0.1 in.)
3 mm
(0.1 in.)
3 mm
(0.1 in.)
3 mm
(0.1 in.)
395 mm
(15.6 in.)
395 mm
(15.6 in.)
500 mm
(19.7 in.)
500 mm
(19.7 in.)
622 mm
(24.5 in.)
559 mm
(22 in.)
559 mm
(22 in.)
648 mm
(25.5 in.)
648 mm
(25.5 in.)
710 mm
(28 in.)
HOT
216 l
(57 gal.)
326 l
(86 gal.)
401 l
(106 gal.)
591 l
(156 gal.)
719 l
(190 gal.)
COLD
98 l
(26 gal.)
136 l
(36 gal.)
178 l
(47 gal.)
265 l
(70 gal.)
322 l
(85 gal.)
Overall Dimensions
Weight and Shipping Information
Wash Cylinder Information
Door Opening Information
Door opening size
Height of door bottom above floor
Water Consumption
Average water consumption
per cycle
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Installation/Operation Supplement
General Specifications
Model
55
75
100
135
165
Motor
0.75 kW/hr
0.95 kW/hr
1.1 kW/hr
1.3 kW/hr
1.6 kW/hr
Heat
3.75 kW/hr
4.5 kW/hr
5.22 kW/hr
6.5 kW/hr
N/A
1
1
1
1
1
4 kW
(5.4 hp)
4 kW
(5.4 hp)
5.5 kW
(7.4 hp)
7.5 kW
(10 hp)
11.5 kW
(15 hp)
Wash/reverse speed
10-50
10-50
10-50
10-50
10-50
Distribution/drain speed
69 rpm
65 rpm
61 rpm
61 rpm
100 rpm
250-1000
rpm
250-1000
rpm
250-800
rpm
250-800
rpm
250-750
rpm
0.04-1.05 Gs
0.05-1.19 Gs
0.06-1.37 Gs
0.06-1.37 Gs
0.06-1.52 Gs
26-418 Gs
30-475 Gs
34-350 Gs
34-350 Gs
34-344 Gs
Standard
Standard
Standard
Standard
Standard
10 mm
(0.38 in.)
10 mm
(0.38 in.)
10 mm
(0.38 in.)
10 mm
(0.38 in.)
19 mm
(0.75 in.)
1
1
1
1
1
Power Consumption
Average power used per cycle
Drive Train Information
Number of motors in drive train
Drive motor power
Cylinder Speeds
Extract speed
Centrifugal Force Data
Wash/reverse centrifugal force
Extract centrifugal force
Balance Detection
Vibration safety switch installed
Direct Steam Heating (Optional)
Steam inlet connection size
Number of steam inlets
Steam required to raise bath
temperature 10°C, kg
(10°F, lb.)
LOW
2.5 kg (3.4 lb.) 3.4 kg (4.6 lb.) 4.5 kg (6.2 lb.) 6.1 kg (8.4 lb.) 7.8 kg (10.3 lb.)
MED
2.8 kg (4 lb.) 3.8 kg (5.5 lb.) 5 kg (6.9 lb.) 6.8 kg (9.3 lb.) 8.4 kg (11.4 lb.)
Average steam use per cycle
23.4 kg
(1.49 bhp)
30.4 kg
(1.94 bhp)
45 kg
(2.87 bhp)
57 kg
(3.63 bhp)
70 kg
(4.4 bhp)
18 kW
18 kW
27 kW
27 kW
N/A
Electrical heating elements
6
6
9
9
N/A
Electrical heat element size
3 kW
3 kW
3 kW
3 kW
N/A
Electrical Heating (Optional)
Total electrical heating capacity
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
General Specifications
Model
Time required to raise bath
temperature
9001014
55
75
100
135
165
10°
C
6 minutes
6 minutes
11 minutes
13 minutes
N/A
50°
F
8 minutes
6 minutes
11 minutes
13 minutes
N/A
ME 10°
D
C
5 minutes
5 minutes
12 minutes
14 minutes
N/A
50°
F
10 minutes
5 minutes
12 minutes
14 minutes
N/A
LO
W
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Installation/Operation Supplement
5
18: 787 mm (31 in.)
25: 884 mm (34.8 in.)
1031 mm
(40.6 in.)
1011 mm
(39.8 in.)
518 mm
(20.4 in.)
279 mm
(11 in.)
486 mm
(19.13 in.)
660 mm
(26 in.)
18: 560 mm
(22.05 in.)
25: 660 mm
(25.98 in.)
CFD530N
CFD530 N
229 mm
(9 in.)
8
152 mm
(6 in.)
74 mm
(2.9 in.)
4
CFS464N
CFS464N
1
2 3
140 mm
(5.5 in.)
7
6
158 mm
(6.2 in.)
780 mm
(30.7 in.)
881 mm
(34.7 in.)
742 mm
(29.2 in.)
9
41 mm
(1.6 in.)
10
389 mm
(15.3 in.)
181 mm
(7.1 in.)
51 mm
(2 in.)
CFS465N
CFS465N
18 AND 25 POUND CAPACITY MODELS WITH U IN THE 8TH POSITION (E.G. *X18PVXU6)
1
2
3
4
5
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
6
7
8
9
10
External Liquid Supply Inlets
Electrical Power Input
External Supply Signal Input
Drain Outlet
Steam Connection Input (Optional)
Figure 1
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
8.66 in.
(220 mm)
10.98 in.
(279 mm)
39.8 in. (1011 mm)
40.87 in. (1038 mm)
11
1.3 in.
(33 mm)
2.56 in.
(65 mm)
1.3 in.
(33 mm)
2.56 in.
(65 mm)
20.87 in. (530 mm)
25.98 in. (660 mm)
1.18 in.
(30 mm)
2.95 in. (75 mm)
CFD521N
1
2
3
4
2.72 in.
(69 mm)
18: 28.62 in. (727 mm)
25: 32.56 in. (827 mm)
5
10
1.18 in.
(30 mm)
18: 26.38 in. (670 mm)
25: 30.31 in. (770 mm)
CFD521N
8.9 in. (226 mm)
5.94 in. (151 mm)
18: 23.23 in. (590 mm)
25: 27.16 in. (690 mm)
CFD522N
CFD522N
6
9
8
7.09 in. (180 mm)
25.98 in. (660 mm)
27.41 in. (696.2 mm)
4.3 in.
(109 mm)
2.76 in. (70 mm)
34.92 in. (887 mm)
31.14in. (791 mm)
29.41 in. (747 mm)
19.1 in. (485 mm)
7
1.73 in.
(44 mm)
CFD528N
CFD528N
18 AND 25 POUND CAPACITY MODELS WITH A OR M IN THE 8TH POSITION (E.G. *X18PVXM6)
1
2
3
4
5
6
Fill and Supply Ventilation
Cold Water Inlet (Required)
External Liquid Supply Inlets
Hot Water Inlet (Required)
Ventilation Tub
Main Switch
7
8
9
10
11
Electrical Power Input
Drain Outlet
Steam Connection Input (Optional)
Cold Water Inlet (Required)
Flushing Supply Dispenser
Figure 2
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Installation/Operation Supplement
5
960 mm
(37.8 in.)
1194 mm
(47 in.)
1176 mm
(46.3 in.)
620 mm
(24.4 in.)
394 mm
(15.5 in.)
639 mm
(25.16 in.)
782 mm
(30.8 in.)
770 mm
(30.31 in.)
CFD531N
CFS467N
CFS467N
328 mm
(12.9 in.)
CFD531N
264 mm
(10.4 in.)
89 mm
(3.5 in.)
3
1
8
2
155 mm
(6.1 in.)
4
7
6
1041 mm
(41 in.)
10
934 mm
(36.75 in.)
965 mm
(38 in.)
1001 mm
(39.4 in.)
889 mm
(35 in.)
9
508 mm
(20 in.)
203 mm
(8 in.)
112 mm
(4.4 in.)
35 POUND CAPACITY MODELS WITH U IN THE
1
2
3
4
5
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
8TH
6
7
8
9
10
CFS468N
POSITION (E.G. *X35PVXU6)
External Liquid Supply Inlets
Electrical Supply Signal Input
External Supply Signal Input
Drain Outlet
Steam Connection Input (Optional)
Figure 3
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
11
8.66 in.
(220 mm)
14.78 in.
(376 mm)
47.32 in. (1202 mm)
46.3 in. (1176 mm)
3.47 in.
(88 mm)
1.34 in.
(34 mm)
1.34 in.
(34 mm)
2.6 in.
(66 mm)
25.51 in. (648 mm)
30.71 in.(780 mm)
2.6 in.
(66 mm)
CFD524N
1.44 in.
(36.5 mm)
CFD524N
13.05 in. (332 mm)
10.49 in. (267 mm)
7.93 in. (202 mm)
4.13 in. (105 mm)
30.12 in. (765 mm)
33.86 in. (860 mm)
3.23 in.
82 mm)
36.06 in. (916 mm)
1.44 in.
(36.5 mm)
CFD525N
CFD525N
1
3
2
10
4
9
5
8
6
4.3 in.
(109.2 mm)
7
7.87 in.
(200 mm)
33.17 in. (843 mm)
2.76 in. (70 mm)
38.11 in. (968 mm)
36.81 in. (935 mm)
35.16 in. (893 mm)
20.87 in. (530 mm)
1.38 in (35 mm)
2.36 in.
(60 mm)
CFD529N
CFD529N
35 POUND CAPACITY MODELS WITH A OR M IN THE 8TH POSITION (E.G. *X35PVXM6)
1
2
3
4
5
6
Fill and Supply Ventilation
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Main Switch
Ventilation Tub
Electrical Power Input
7
8
9
10
11
Drain Outlet
Steam Connection Input (Optional)
External Liquid Supply Inlets
Cold Water Inlet (Required)
Flushing Supply Dispenser
Figure 4
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Installation/Operation Supplement
5
1016 mm
(40 in.)
1544 mm
(60.8 in.)
1499 mm
(59 in.)
859 mm
(33.8 in.)
559 mm
(22 in.)
740 mm
(29.13 in.)
900 mm
(35.43 in.)
830 mm
(32.68 in.)
102 mm
(4 in.)
CFS470N
CFD509N
CFS470N
CFD509N
91 mm
(13.6 in.)
254 mm
(10 in.)
252 mm
(9.9 in.)
158 mm
(6.2 in.)
2
3
4
99 mm
(3.9 in.)
1
6
191 mm
(7.5 in.)
1389 mm
(54.7 in.)
11
1283 mm
(50.5 in.)
8
7
36 mm
(1.4 in.)
721 mm
(28.4 in.)
165 mm
(6.5 in.)
165 mm
(6.5 in.)
9
10
104 mm
(4.1 in.)
104 mm
(4.1 in.)
CFS471N
CFS471N
55 MODEL
1
2
3
4
5
6
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
7
8
9
10
11
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Figure 5
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
5
1168 mm
(46 in.)
1575 mm
(62 in.)
853 mm
(33.6 in.)
1532 mm
(60.3 in.)
559 mm
(22 in.)
102 mm
(4 in.)
870 mm
(34.25 in.)
1060 mm
(41.73 in.)
488 mm
(19.2 in.)
CFD510N
960 mm
(37.8 in.)
CFD510N
CFS473N
366 mm
(14.4 in.)
CFS473N
246 mm
(9.7 in.)
2 3 4
229 mm
(9 in.)
94 mm
(3.7 in.)
1
175 mm
(6.9 in.)
6
1407 mm
(55.4 in.)
7
11
1315 mm
(51.75 in.)
8
43 mm
(1.7 in.)
582 mm
(22.9 in.)
170 mm
(6.7 in.)
10
9
104 mm
(4.1 in.)
CFS474N
CFS474N
104 mm
(4.1 in.)
75 MODEL
1
2
3
4
5
6
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
7
8
9
10
11
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Figure 6
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Installation/Operation Supplement
100: 1331 mm (52.4 in.)
135: 1506 mm (59.3 in.)
6
1951 mm
(76.8 in.)
960 mm
(37.8 in.)
648 mm
(25.5 in.)
102 mm
(4 in.)
1040 mm
(40.94 in.)
1200 mm
(47.24 in.)
CFD511N
CFD511N
100: 1010 mm
(39.76 in.)
305 mm
(12 in.)
2362 mm
(9.3 in.)
135: 1185 mm
(46.65 in)
CFS476N
CFS476N
175 mm
(6.9 in.)
89 mm
(3.5 in.)
114 mm
(4.5 in.)
104 mm
(4.1 in.)
165 mm
(6.5 in.)
2 3 5
170 mm
(6.7 in.)
51 mm
(2 in.)
249 mm
(9.8 in.)
1
221 mm
(8.7 in.)
4
9
7
1575 mm
(62 in.)
13
12
8
10
696 mm
(27.4 in.)
216 mm
(8.5 in.)
216 mm
(8.5 in.)
11
1
2
3
4
5
6
7
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
100 AND 135 MODELS
8
9
10
11
12
13
185 mm
(7.3 in.)
CFS477N
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Service Power Disconnect
Figure 7
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
1620 mm
(63.8 in.)
6
2100 mm
(82.7 in.)
1020 mm
(40.2 in.)
641 mm
(25.25 in.)
102 mm
(4 in.)
1140 mm
(44.9 in.)
1300 mm
(51.2 in.)
CFD511N
CFD511N
360 mm
(14.25 in.)
273 mm
(10.75 in.)
1185 mm
(46.7 in.)
198 mm
(7.8 in.)
CFD15N
CFD15N
122 mm
(4.8 in.)
114 mm
(4.5 in.)
114 mm
(4.5 in.)
2
172 mm
(6.75 in.)
35
51 mm
(2 in.)
197 mm
(7.75 in.)
260 mm
(10.24 in.)
1
221 mm
(8.7 in.)
4
9
7
1854 mm
(73 in.)
13
12
8
10
696 mm
(27.4 in.)
254 mm
(10 in.)
11
1
2
3
4
5
6
7
Fill and Supply Ventilation
Cold Water Inlet (Required)
Hot Water Inlet (Required)
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Flushing Supply Dispenser
External Liquid Supply Inlets
165 MODEL
8
9
10
11
12
13
254 mm
(10 in.)
236 mm
(9.3 in.)
CFS477N
Electrical Power Input
External Supply Signal Input
Drain Outlet
Reuse Drain Outlet (Optional)
Steam Connection Input (Optional)
Service Power Disconnect
Figure 8
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Installation/Operation Supplement
Installation
Dimensional Clearances
Table 1 shows recommended minimum clearances on
all sides of the washer-extractor.
Recommended Minimum Clearances
Model
18
25
35
55
75
100
135
165
Minimum rear clearance
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
Minimum clearance between
machine and wall
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
Minimum clearance between
machines (side)
25.4 mm
(1 in.)
25.4 mm
(1 in.)
25.4 mm
(1 in.)
30 mm
(1.2 in.)
30 mm
(1.2 in.)
30 mm
(1.2 in.)
30 mm
(1.2 in.)
30 mm
(1.2 in.)
Minimum front clearance
(door swing)
419 mm
(16.5 in.)
419 mm
(16.5 in.)
419 mm
(16.5 in.)
533 mm
(21 in.)
533 mm
(21 in.)
660 mm
(26 in.)
660 mm
(26 in.)
660 mm
(26 in.)
Table 1
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
Machine Foundation
The washer-extractor must be placed on a smooth level
surface so that the entire base of the machine is
supported and rests on the mounting surface.
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
extract.
The standard installation does not require anchoring
unless mandated by state or local codes.
Static and dynamic loads on the floor or foundation are
shown in Table 2.
CAUTION
Table 2 can be used as a reference when designing
floors and foundations.
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
W488
Floor Load Data
Model
18
25
35
55
75
100
135
165
Static floor
load
2.51 kN
(546 lb.)
2.63 kN
(592 lb.)
4.38 kN
(983 lb.)
6.97 kN
(1566 lb.)
10.3 kN
(2310 lb.)
16.4 kN
(3682 lb.)
19.1 kN
(4282 lb.)
24.49 kN
(5509 lb.)
Static
pressure
6.79 kN-m2 5.17 kN-m2 6.53 kN-m2 8.33 kN-m2 8.97 kN-m2 11.5 kN-m2 12.5 kN-m2 14.84 kN-m2
(137 lbs-ft2) (109 lbs-ft2) (137 lbs-ft2) (175 lbs-ft2) (188 lbs-ft2) (240 lbs-ft2) (261 lbs-ft2) (310 lbs-ft2)
Dynamic
floor load
0.7 kN
(157 lb.)
0.75 kN
(169 lb.)
1.2 kN
(270 lb.)
1.7 kN
(382 lb.)
2.0 kN
(450 lb.)
2.96 kN
(665 lb.)
3.75 kN
(883 lb.)
4.86 kN
(1093 lb.)
Maximum
dynamic
load
0.7 kN
(157 lb.)
0.75 kN
(169 lb.)
1.2 kN
(270 lb.)
1.7 kN
(382 lb.)
2.0 kN
(450 lb.)
2.96 kN
(665 lb.)
3.75 kN
(883 lb.)
5.78 kN
(1301 lb.)
Dynamic
pressure
1.89 kN-m2 1.47 kN-m2 1.79 kN-m2 2.03 kN-m2 7.75 kN-m2 2.07 kN-m2 2.46 kN-m2 3.05 kN-m2
(39.4 lbs-ft2) (31.1 lbs-ft2) (37.6 lbs-ft2) (42.7 lbs-ft2) (36.6 lbs-ft2) (43.3 lbs-ft2) (53.8 lbs-ft2) (63.7 lbs-ft2)
Table 2
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Installation/Operation Supplement
Mechanical Installation
Frame Dimensions and Mounting Bolt
Location for 18, 25, 35, 55, 75, 100, 135
and 165 Models
55 mm
(2.17 in.)
660 mm
(26 in.)
782 mm
(30.8 in.)
860 mm
(33.85 in.)
770 mm
(30.31 in.)
670 mm
(26.38 in.)
560 mm
(22.05 in.)
45 mm
(1.77 in.)
45 mm
(1.77 in.)
71 mm
(2.78 in.)
639 mm
(25.16 in.)
35 MODEL
71 mm
(2.78 in.)
CFS480N
CFS480N
55 mm
(2.17 in.)
87 mm
(3.43 in.)
486 mm
(19.13 in.)
Figure 11
87 mm
CFS479N
(3.43
in.)
18 MODEL
CFS479N
898 mm
(35.35 in.)
50 mm
(1.97 in.)
Figure 9
55 mm
(2.17 in.)
660 mm
(26 in.)
830 mm
(32.68 in.)
660 mm
(25.98 in.)
930 mm
(36.61 in.)
770 mm
(30.31 in.)
50 mm
(1.97 in.)
740 mm
(29.13 in.)
80 mm
(3.15 in.)
55 MODEL
55 mm
(2.17 in.)
87 mm
(3.43 in.)
486 mm
(19.13 in.)
25 MODEL
87 mm
(3.43 in.)
CFS478N
80 mm
(3.15 in.)
CFS481N
CFS481N
Figure 12
CFS478N
Figure 10
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
1060 mm
(41.73 in.)
60 mm
(2.36 in.)
960 mm
(37.8 in.)
60 mm
(2.36 in.)
1080 mm
(42.52 in.)
95 mm
(3.74 in.)
75 MODEL
1270 mm
(50 in.)
1185 mm
(46.65 in.)
42,5 mm
(1.67 in.)
870 mm
(34.25 in.)
95 mm
(3.74 in.)
1200 mm
(47.24 in.)
42,5 mm
(1.67 in.)
1040 mm
(40.94 in.)
80 mm
(3.15 in.)
80 mm
(3.15 in.)
135 MODEL
CFS483N
CFS484N
CFS483N
Figure 15
Figure 13
40 mm
(1.57 in.)
1200 mm
(47.24 in.)
1090 mm
(42.91 in.)
1010 mm
(39.76 in.)
40 mm
(1.57 in.)
80 mm
(3.15 in.)
100 MODEL
CFS482N
1251 mm
(49.25 in.)
1185 mm
(46.7 in.)
33 mm
(1.3 in.)
1040 mm
(40.94 in.)
80 mm
(3.15 in.)
1300 mm
(51.2 in.)
33 mm
(1.3 in.)
80 mm
(3.15 in.)
1140 mm
(44.9 in.)
165 MODEL
CFS482N
Figure 14
9001014
80 mm
(3.15 in.)
CFS484N
Figure 16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Installation/Operation Supplement
Mounting Bolt Installation
(If Required)
4. To level machine, fill the spaces between the
machine base and floor with machinery grout.
Grout completely under all frame members.
Remove front and rear panels to gain access to all
frame members. Force grout under the machine
base until all voids are filled.
1
2
5. Remove the spacers carefully, allowing the
machine to settle into the wet grout.
3
6. Position washers and locknuts on machinery
anchor bolts and finger-tighten to machine base.
7. After the grout is completely dry, tighten the
locknuts by even increments – one after the
other – until all are tightened evenly and the
machine is fastened securely to the floor.
152 mm
(6 in.)
8. Remove the four red transport brackets which
secure the moving components of the machine
during shipping. Refer to Installation manual for
typical transport bracket locations.
CFS485N
4
CFS485N
1
2
3
4
Base Frame
Bolt
Washer
Anchor Bolt/Plug
Figure 17
After the concrete has cured and the anchors are
installed, proceed as follows:
1. Place the washer-extractor adjacent to the
foundation. Do not attempt to move it by pushing
on the sides. Always insert a pry bar or other
device under the bottom of the frame of the
washer-extractor to move it.
2. Place the washer-extractor carefully over the
anchors.
3. Put bolts through the machine in the anchors and
fasten them. (For the 18-25 and 35 models, the
diameter of the bolt must be minimum 1/2-13 or
12 mm; for the 55-75-100-135-165 models, the
diameter of the bolt must be minimum 5/8-11 or
16 mm.)
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
Electrical Specifications
Electrical Specifications
Voltage Designation
Standard
Electric Heat
AWG/mm2
Full Load
Amps
Circuit
Breaker
AWG/mm2
Not available
28
30
10/6.0
Circuit
Breaker
12/4.0
Full Load
Amps
20
Wire
17
Phase
Not available
Cycle
10/6.0
Voltage
25
Code
20
Model
14/2.5
18
N
440-480
50/60
3
3+PE
6
15
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
2/3+PE
6
15
14/2.5
N
440-480
50/60
3
3+PE
6
15
14/2.5
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
2/3+PE
6
15
14/2.5
N
440-480
50/60
3
3+PE
12
15
14/2.5
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
2/3+PE
12
15
14/2.5
N
440-480
50/60
3
3+PE
12
15
14/2.5
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
2/3+PE
12
15
14/2.5
N
440-480
50/60
3
3+PE
12
15
14/2.5
41
50
8/10.0
P
380-415
50/60
3
3+N+PE
12
15
14/2.5
36
40
8/10.0
Q
200-240
50/60
3
3+PE
12
20
12/4.0
58
60
6/16.0
N
440-480
50/60
3
3+PE
17
20
12/4.0
62
70
4/25.0
P
380-415
50/60
3
3+N+PE
17
20
12/4.0
55
60
6/16.0
Q
200-240
50/60
3
3+PE
17
25
10/6.0
88
90
3/35.0
N
440-480
50/60
3
3+PE
17
25
10/6.0
62
70
4/25.0
P
380-415
50/60
3
3+N+PE
17
25
10/6.0
55
60
6/16.0
Q
200-240
50/60
3
3+PE
17
30
10/6.0
88
90
3/35.0
N
440-480
50/60
3
3+PE
20
25
10/6.0
Not available
P
380-415
50/60
3
3+N+PE
20
25
10/6.0
Not available
Q
200-240
50/60
3
3+PE
25
40
8/10.0
Not available
25
35
55
75
100
135
165
Not available
21
25
10/6.0
Not available
18
20
12/4.0
Not available
29
30
10/6.0
Not available
41
50
8/10.0
Not available
36
40
8/10.0
Not available
58
60
6/16.0
Not available
41
50
8/10.0
Not available
36
40
8/10.0
Not available
58
60
6/16.0
Not available
Table 3
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Installation/Operation Supplement
Operation
Control Identification
3
2
5
1
1
2
3
Keypad
Display
Emergency Stop Button
4
5
4
Key Switch
Serial Port
Figure 18
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Installation/Operation Supplement
Load the Machine
For models: 100PV-165PV
For models: 18PV-55PV
SX100PV
UX100PV
SX18PV
SX25PV
UX18PV
UX25PV
SX135PV
UX135PV
SX35PV
SX55PV
UX35PV
UX55PV
SX165PV
UX165PV
SX75PV
UX75PV
1. Pull the door handle towards you to open the
door.
Some models may have a door handle with a button
that must be pressed.
1. Push on the doorlock system to open the door.
2. Load the drum to the specified capacity.
3. Close the door by pushing the door handle
towards the machine.
2. Load the drum to the specified capacity.
3. Close the door by pushing the door handle
towards the machine.
9001014
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Installation/Operation Supplement
Disposal of Unit
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Refer to Figure 19. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment.
Ensuring this product is disposed of correctly will help
prevent potential negative consequences for the
environment and human health which could otherwise
be caused by inappropriate waste handling of this
product. The recycling of materials will help to
conserve natural resources. For more detailed
information about recycling of this product, please
contact the local city office, household waste disposal
service, or the source from which the product was
purchased.
28
MIX1N
Figure 19
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001014
Download PDF

advertising