Owner`s manual | Alpine TME-M790 Car Video System User Manual

R
EN
TME-M790
MOBILE MULTIMEDIA MONITOR
• OWNER'S MANUAL
Please read before using this equipment.
DE
• MODE D'EMPLOI
Veuillez lire avant d’utiliser cet appareil.
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
FR
ES
ES
ALPINE ELECTRONICS, INC.
Tokyo office: 1-1-8 Nishi Gotanda,
Shinagawa-ku,
Tokyo 141-8501, Japan
Tel.: (03) 3494-1101
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Tel.: 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC.
Suite 203, 7300 Warden Ave. Markham,
Ontario L3R 9Z6, Canada
Tel.: 1-800-ALPINE-1 (1-800-257-4631)
Sankei Kikaku Co., Ltd.
1-13-38, Hinodai, Hino, Tokyo, Japan
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
Tel.: (03) 9769-0000
ALPINE ELECTRONICS GmbH
Kreuzerkamp 7-11 40878 Ratingen, Germany
Tel.: 02102-45 50
ALPINE ITALIA S.p.A.
Via C. Colombo 8, 20090 Trezzano Sul Naviglio
MI, Italy
Tel.: 02-48 47 81
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue De La Belle Etoile, Z.I. Paris Nord Il
B.P. 50016 F-95945, Roissy, Charles De Gaulle
Cedex, France
Tel.: 01-48 63 89 89
ALPINE ELECTRONICS OF U.K., LTD.
13 Tanners Drive, Blakelands, Milton Keynes
MK14 5BU, U.K.
Tel.: 01908-61 15 56
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal De Gamarra 36, Pabellón 32
01013 Vitoria (Alava)-Apdo. 133, Spain
Tel.: 34-45-283588
Designed by ALPINE Japan
Printed in Japan (S)
68P30540Y57-A
SE
ENGLISH
Contents
Operating Instructions
WARNING
Information
In Case of Difficulty ........................................ 13
Specifications ................................................... 13
WARNING .................................................. 2
CAUTION ................................................... 3
PRECAUTIONS ......................................... 3
Basic Operations
Using Face Cover ............................................... 4
Initial System Start-up ....................................... 4
Raising the Monitor ........................................... 4
Lowering the Monitor ........................................ 4
Turning Power On or Off ................................... 5
Selecting the Monitor Opening Angle ............... 5
Installation and Connections
Warning ............................................................ 14
Caution ............................................................. 14
Precautions ....................................................... 15
Installation ....................................................... 16
FR
Connections ..................................................... 18
System Connections ......................................... 19
LIMITED WARRANTY
Adjusting the Monitor Viewing Angle ............... 5
ES
Adjusting the Volume ........................................ 5
Switching the Source ......................................... 5
Switching Display Modes .................................. 6
Other Useful Features
Adjusting Brightness of Picture ......................... 8
DE
Adjusting Color Density of Picture ................... 8
Adjusting Tint of Picture .................................... 8
Setting the Brightness of the Backlight ............. 9
Adjusting the Lowest Level of the Backlight .... 9
Setting Automatic Opening/
Closing of Monitor ............................................. 9
IT
Selecting Rear Monitor .................................... 10
Setting the External Device Interrupt Mode .... 10
Switching the Opening Screen ......................... 11
Turning Sound Guide Function On or Off ....... 11
Switching the Video Screen ............................. 11
Using the External Input Terminal ................... 11
SE
Operating with the Remote Control Unit
(RUE-4165 Sold Separately) ........................... 12
1-EN
WARNING
WARNING
This symbol means important instructions.
Failure to heed them can result in serious
injury or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES
YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.
Any function that requires your prolonged attention
should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before
performing these functions. Failure to do so may result in
an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN
STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking
ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in
fire, electric shock or other injury.
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF
THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
DO NOT PLACE HANDS, FINGERS OR FOREIGN
OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the
product.
USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.
Failure to do so may result in fire or electric shock.
2-EN
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result
in fire.
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from looking
ahead of the vehicle and cause an accident.
INSTALL THE PRODUCT CORRECTLY SO THAT THE
DRIVER CANNOT WATCH TV/VIDEO UNLESS THE
VEHICLE IS STOPPED AND THE EMERGENCY BRAKE
IS APPLIED.
It is dangerous (and illegal in many states) for the driver
to watch TV/Video while driving a vehicle. Installing this
product incorrectly enables the driver to watch TV/Video
while driving. This may cause a distraction, preventing
the driver from looking ahead, thus causing an accident.
The driver or other people could be severely injured.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to
the product. Return it to your authorized Alpine dealer or
the nearest Alpine Service Center for repairing.
KEEP FINGERS AWAY WHILE THE MOTORIZED
FRONT PANEL OR MOVING MONITOR IS IN
PRECAUTIONS
Temperature
Be sure the temperature inside the vehicle is between
+45°C (+113°F) and 0°C (+32°F) before turning your unit
on.
Fuse Replacement
When replacing the fuse(s), the replacement must be of
the same amperage as shown on the fuse holder. If the
fuse(s) blows more than once, carefully check all
electrical connections for shorted circuitry. Also have your
vehicle’s voltage regulator checked.
FR
MOTION.
Failure to do so may result in personal injury or damage
to the product.
Maintenance
If you have problems, do not attempt to repair the unit
yourself. Return it to your Alpine dealer or the nearest
Alpine Service Station for servicing.
Installation Location
ES
Make sure the TME-M790 will not be exposed to:
• Direct sun and heat
• High humidity
• Excessive dust
• Excessive vibrations
• After turning the system off, a slight ghost of the image
will remain temporarily. This is an effect peculiar to
LCD technology and is normal.
• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.
DE
IT
SE
3-EN
Basic Operations
9 8
OPEN/CLOSE
RESET switch PWR
NOTES
• If the monitor touches an obstacle while it is
being raised, the unit will stop raising the
monitor immediately. Should this occur, remove the
obstacle and press the OPEN/CLOSE button again to
raise the monitor.
• When the movable monitor is opened, do not place
any object on the monitor and be careful not to bump
or apply any pressure to the monitor while it is open.
This can cause damage to the mechanism.
• Under low ambient temperature conditions, the
display may be dark for a short period of time
immediately after the power is turned on. Once the
LCD has warmed up, the display will return to
normal.
• For your safety, some operation of the unit
cannot be performed while the vehicle is in
motion. In this case, first stop the vehicle and
engage the parking brake, then perform the
operation.
An anti-theft face cover is provided with the TMEM790.
Put the face cover onto the TME-M790 when you
leave the vehicle.
Be sure to remove the anti-theft face cover when
you drive.
Lowering the Monitor
Immediately after installing or applying power to
the unit, it should be initialized.
1
At the lower left corner of the screen front panel,
there is a small button. Using a pencil or other
pointed object, press this RESET switch to
complete the initialization procedure.
Raising the Monitor
NOTE
The TME-M790 is a precision device. With careful
handling, its performance can be maintained at a high
level for a long time.
1
Press the OPEN/CLOSE button.
The unit beeps 3 times and raises the monitor
automatically.
4-EN
-
AUX
Using Face Cover
Initial System Start-up
/
NOTE
The TME-M790 is a precision device. With careful
handling, its performance can be maintained at a high
level for a long time.
1
Press the OPEN/CLOSE button.
The unit will beep 3 times and lower the monitor
automatically.
NOTE
If the monitor touches an obstacle while it is being
lowered, the unit will stop lowering the monitor
immediately.
Should this occur, remove the obstacle and press the
OPEN/CLOSE button again to lower the monitor.
Turning Power On or Off
1
2
Press the PWR (Power) button to turn on the unit.
The opening screen appears automatically.
Press the PWR (Power) button again to turn off
the unit.
NOTES
• The TME-M790 draws minimal current even
when its power switch is turned off. If the
switched power (ignition) lead of the TMEM790 is connected directly to the positive (+)
post of the vehicle's battery, the battery may be
discharged. If this lead is unswitched, it must
be disconnected from the battery post should
the vehicle be left unused for an extended
period of time.
An SPST (Single-Pole, Single-Throw) switch (sold
separately) can be added to simplify this procedure.
Then, you can simply place it in the OFF position
when you leave the vehicle. Turn the SPST switch
back ON before using the TME-M790. For
connecting the SPST switch, refer to the Installation.
• Some operation of the unit cannot be performed
while the vehicle is in motion. In this case, be sure to
first stop your vehicle and apply the parking brake,
then perform the operation.
• After turning the system off, a slight ghost of the
image will remain temporarily. This is an effect
peculiar to LCD technology and is normal.
• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.
Selecting the Monitor Opening
Angle
Adjusting the Monitor Viewing
Angle
Adjust the monitor's angle for better visibility.
1
2
NOTES
• The angle changes continuously if the 9 and 8
buttons or the 4 and 3 buttons are held down.
• If there are any obstructions to the monitor
when adjusting the angle, first remove the
obstruction and then readjust the angle.
• The screen color will vary when viewed at certain
angles. Adjust the screen angle for the best viewing
position.
• If the voltage of the vehicle's battery power is
low, the screen may blink when the screen angle is
changed. This is normal and not a malfunction.
• The adjusted angle is stored in the memory.
Press and hold the OPEN/CLOSE button for at
least 2 seconds while the monitor is being
raised. Each press changes the monitor angle
back or forth.
NOTE
When the OPEN/CLOSE button is pressed and held for
at least 2 seconds when the neck angle is adjusted, the
neck angle adjustment is canceled.
After doing this, adjust the display in the front/rear
direction.
FR
ES
Adjusting the Volume
1
The monitor opening angle can be set in 2
positions.
1
While viewing the screen that is shown press the
9 or 8 button to adjust the display to the ideal
viewing angle.
The display viewing angle can be adjusted
between 40 and 105 degrees.
Press the 4 or 3 button to adjust the right-left
viewing angle. It is possible to adjust the display
viewing angle up to 15 degrees to the left or
right.
Press and hold the OPEN/CLOSE button for at
least 2 seconds to cancel the neck angle
adjustment.
Press the
or
button to adjust the volume.
NOTE
The volume changes continuously if the
button is held down.
DE
or
Switching the Source
1
Press the AUX button. Each press of the button
will cycle through the modes as follows:
NAVIGATION
AUX1
IT
AUX2
SE
5-EN
Basic Operations
DISP
Switching Display Modes
Viewing the switching display modes
To watch a video source, your vehicle must be
parked with the ignition key in the ACC or ON
position. To do this, follow the procedure below.
1. Push the foot brake to bring your vehicle to a
complete stop at a safe location. Engage the
parking brake.
1
Press and hold the DISP button for at least 2
seconds. Each press changes the display modes
as follows:
MODE 1
(WIDE)
MODE 2
(ZOOM)
MODE 3
(CINEMA)
MODE 4
(NORMAL)
2. Keep pushing the foot brake and release the
parking brake once then engage it again.
3. While the parking brake is being engaged the
second time, release the foot brake.
NOTE
For automatic transmission vehicles, place the
transmission lever in the Park position.
The video lock-out system is now disabled.
Unless ignition is turned OFF, this mode can be
reactivated by simply engaging the parking
brake, without performing the entire procedure
above (1 through 3).
If the ignition is turned OFF position, you must
perform the entire procedure above.
NOTE
Trying to access the switching display modes while
driving will display the warning - PICTURE OFF
FOR YOUR SAFETY.
MODE 1 (WIDE)
Stretches the normal image evenly in a
horizontal direction so that it is displayed on the
entire screen.
MODE 2 (ZOOM)
Stretches the normal image evenly in a
horizontal direction so that it is displayed on the
entire screen. The stretching ratio increases the
closer to the left or right edge of the screen.
6-EN
MODE 3 (CINEMA)
Stretches the normal image horizontally and
vertically.
The top and bottom of the screen is cut slightly
to adapt it to a cinema size image with a
proportion of 16:9.
FR
MODE 4 (NORMAL)
ES
A normal television broadcasting (4:3) image is
displayed in the center (normal image).
DE
IT
SE
7-EN
Other Useful Features
/
9 8
AUX
SET UP
Adjusting Brightness of Picture
3
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1
2
3
AUX1
BRIGHT
COLOR
TINT
AUX OUT
4
AUX1
MIN
4
Press the SET UP button to finish adjustments.
Adjusting Tint of Picture
MAX
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
Press the SET UP button to finish adjustments.
NOTE
If the AUX button is pressed and held for 2 seconds or
more while in the adjustment screen, the setting of the
brightness, color density, and tint is reset back to its
center value.
1
2
3
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select TINT.
Press the 4 or 3 button within 10 seconds to
adjust the tint.
SET UP
Adjusting Color Density of Picture
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1
2
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select COLOR.
8-EN
+
NOTES
• If the AUX button is pressed and held for 2 seconds
or more while in the adjustment screen, the setting of
the brightness, color density, and tint is reset back to
its center value.
• The color density cannot be adjusted in the
NAVIGATION (RGB connection) mode.
SET UP
1
0
3
0
0
LINK
1
0
3
0
0
LINK
–
Press the 4 or 3 button within 10 seconds to
adjust the brightness.
BRIGHT
COLOR
TINT
AUX OUT
Press the 4 or 3 button within 10 seconds to
adjust the color density.
SET UP
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select BRIGHT.
-
AUX1
BRIGHT
COLOR
TINT
AUX OUT
R
4
1
0
3
0
0
LINK
G
Press the SET UP button to finish adjustments.
NOTES
• If the AUX button is pressed and held for 2 seconds
or more while in the adjustment screen, the setting of
the brightness, color density, and tint is reset back to
its center value.
• The tint cannot be adjusted in the NAVIGATION
(RGB connection) mode.
Setting the Brightness of the
Backlight
3
Press the 4 or 3 button within 10 seconds to set
the value.
SET UP
AUX1
It is possible to change the brightness of the LCD
panel's backlighting to more closely conform to
the vehicle's interior lighting. This makes the
screen easier to view.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1
2
3
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select DIMMER.
DIMMER AUTO
DIMMER Lv. OPEN/CLOSE OFF
OUT INT. ON
LOW
4
3
HIGH
Press the SET UP button to finish adjustments.
Setting Automatic Opening/
Closing of Monitor
Simply turn the ignition key to ACC ON or OFF to
automatically open or close the TV display.
Press the 4 or 3 button within 10 seconds to set
the value.
AUTO:
Automatic adjustment of the screen brightness in
conformity with vehicle interior brightness.
HIGH:
Maximum screen brightness.
LOW:
The preset screen brightness that was set when
adjusting the minimum backlight level.
2
FR
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1
2
3
Press the SET UP button.
Press the 9 or 8 button within 10 seconds to
select OPEN/CLOSE.
ES
Press the 4 or 3 button within 10 seconds to set
the value.
SET UP
AUX1
DIMMER AUTO
DIMMER Lv. OPEN/CLOSE OFF
OUT INT. ON
2
3
AUTO HIGH LOW
4
Press the SET UP button to finish adjustments.
AUTO:
Automatic opening or closing of the display in
depending upon whether the ignition switch is ON
or OFF.
OFF:
Manual opening or closing of the display.
SET UP
Adjusting the Lowest Level of the
Backlight
It is possible with this equipment to adjust the
minimum brightness level for backlighting (LOW).
This is useful, for matching the screen brightness
to the dashboard for driving at night. This setting
is recalled with the AUTO setting corresponding
to the vehicle's interior lighting.
AUX1
DIMMER AUTO
DIMMER Lv. OPEN/CLOSE OFF
OUT INT. ON
2
3
IT
AUTO OFF
4
Press the SET UP button to finish adjustments.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1
2
DE
SE
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select DIMMER Lv.
9-EN
Other Useful Features
/
9 8
PWR SET UP
Selecting Rear Monitor
This unit has controls to switch the video and
audio to a rear monitor if another (rear) monitor
is connected.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1
2
3
Press the 4 or 3 button within 10 seconds to
carry out selection.
LINK:
Output the video/audio portion shown on the main
monitor, to the rear monitor.
NAV.:
Output the navigation video/audio to the rear
monitor. (Only when navigation unit is connected).
AUX 1:
Output the AUX 1 video/audio to the rear monitor.
AUX 2:
Output the AUX 2 video/audio to the rear monitor.
SET UP
AUX1
BRIGHT
COLOR
TINT
AUX OUT
LINK
4
V. SEL
Setting the External Device
Interrupt Mode
When used in conjunction with an Ai interception
box (KCA-801B), the sound of a TV or an
external input sound can be intercepted to an
Alpine head unit. This function may not work
with some combinations of products. For details,
refer to the KCA-801B’s operating instructions.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select AUX OUT.
1
0
3
0
0
LINK
NAV. AUX1 AUX2
Press the SET UP button to finish adjustments.
10-EN
-
1
2
3
Press the SET UP button.
Press the 9 or 8 button within 10 seconds and
select OUT INT.
Press the 4 or 3 button within 10 seconds to
turn ON.
SET UP
AUX1
DIMMER AUTO
DIMMER Lv. OPEN/CLOSE OFF
OUT INT. ON
OFF
4
2
3
ON
Press the SET UP button to finish adjustments.
Switching the Opening Screen
You can change the opening screen to your liking.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
Switching the Video Screen
It is possible to change the video source for
display while retaining the present audio portion.
1
Press the V.SEL button.
NAVIGATION
Press the 9 or 8 button within 10 seconds and
select H.U. IND.
Press the
or
button within 10 seconds to
set the selection.
9
3
Press the SET UP button.
9
1
2
ON:
Special opening screen.
This setting is used when combining with the
Flagship System model.
OFF:
Normal opening screen.
2
AUX2
To release press and hold the V.SEL button for 2
seconds.
Using the External Input Terminal
It is possible to enjoy video and sound from a
video camera, etc. by simply connecting it with
an optional adapter cable.
Video camera, etc.
AUDIO OUT
R
ES
AUX1
H.U. IND.
OFF
4
ON
FR
Main unit
VIDEO OUT L
SET UP
AUX1
3
3
ON
Press the SET UP button to finish adjustments.
Optional adapter cable
(RCA pin plugs
[yellow, red, white]
3.5ø miniplugs).
NOTE
With the above connections, video source switching and
settings and adjustments at adjustment screens are not
possible.
DE
Turning Sound Guide Function
On or Off
This function will give audible feedback with
varying tones depending upon the button
pressed.
IT
1
Press and hold the PWR button for 2 seconds
with the power OFF and turn the Sound Guide
ON or OFF.
SE
11-EN
Other Useful Features
Remote Control Sensor
RUE-4165
Remote Control Signal Transmitter
2
VO
LU
P
L DN
VO
Signal Transmitter Indicator
5
ENT
1
DISP
4
6
LIST
SOURCE
BAND
CANC.
MENU
A.PROC
DEFEAT
3
Remote Sensor Remote Sensor
(when the display
(when the display
is stowed away)
is raised)
7
MUTE
8
VOICE
N/H
MP/RG
LIST
TUNER
DETOUR
DISC
PLAN
CHG
POWER
r
DISP
ON/OFF
1
2
3
4
5
6
7
8
9
DEL
0
OK
9
• Point the remote control transmitter
toward the remote sensor on the TMEM790 and use the remote control within
2 meters from the TME-M790.
p
V.SEL
t
q
DEL DEST.
w
e
(When the flip cover is open)
Operating with the Remote Control
Unit (RUE-4165 Sold Separately)
Button
No.
1
ENT
2
3
LIST
4
5
Button
No.
RUE-4165
Select the item on the adjustment screen.
Moves to the left or right when you press
on the or side.
Moves up and down when you press
on the or side.
p
9
Display angle adjustment (right).
Changes continuously when held down.
q
DEL
Display angle adjustment (down).
Changes continuously when held down.
Volume increases when turned in a
clockwise direction.
Volume decreases when turned in a
counter-clockwise direction.
w
OK
Display angle adjustment (up).
Changes continuously when held down.
e
0
RUE-4165
DISP
NAVI / AUDIO
6
7
8
SOURCE
MENU
BAND
CANC.
Volume increases.
Changes continuously when held down.
Volume decreases.
Changes continuously when held down.
When operating this equipment,
change to the NAVI side.
Displays the adjustment screen.
Terminates the adjustment screen.
MUTE
The display mode changes.
MP/RG
9
12-EN
8
Display angle adjustment (left).
Changes continuously when held down.
r
When pressed less than 2 seconds:
OPEN/CLOSE of display.
When pressed at least 2 seconds:
Display slides forward and backward.
POWER
DISP
ON/OFF
Power ON/OFF.
V.SEL
t
Switch the video source.
DEL DEST.
NAVI / AUDIO
When switch 5 is set to the AUDIO side.
Information
In Case of Difficulty
If you encounter a problem, please review the items in
the following checklist. This guide will help you isolate
the problem if the unit is at fault. Otherwise, make sure
the rest of your system is properly connected or consult
your authorized Alpine dealer.
No function or display.
• Car's ignition is off.
- Turn the ignition on.
• No fuse or blown fuse.
- Check the cause and replace the fuse.
• Incorrect connections.
- Check connection and remedy.
• Vehicle's battery is weak.
- Check the voltage of vehicle's battery.
Specifications
MONITOR SECTION
Screen Size
LCD Type
Operation System
Number of Picture Elements
Effective Number of
Picture Elements
Illumination System
• Fluorescent tube is exhausted.
- Replace the fluorescent tube.*
No picture display.
GENERAL
• Brightness control is set for minimum brightness control.
- Adjust the brightness.
• Incorrect setting of the VCR mode.
- Switch to the correct mode.
• Protective circuit is on because of high temperature.
- Wait until the temperature inside the vehicle comes
down to the operating temperature range (45°C).
• Incorrect or open connection with the Monitor, AV
interface unit.
- Check the connection and remedy.
Power Requirement
Operating temperature
Weight
(Monitor Section)
(AV-Interface Unit Section)
Picture color is poor.
• Brightness/Color/Tint control are not set to the proper
positions.
- Check each control.
Spots or dotted lines/stripes appear.
• Caused by neon signs, high-voltage power lines, CB
transmitter, other vehicle's ignition plugs, etc.
- Change the location of your vehicle.
The display angle cannot be adjusted or the
adjustment screen does not appear.
• Mechanism error.
- Press the OPEN/CLOSE button to stow away the
display, and raise the display again.
* The fluorescent tube replacement is not free of charge
even within the warranty period, for the tube is an article
of consumption.
99.99% or more
Cold cathode
fluorescent tube
AV-INTERFACE UNIT SECTION
S/N Ratio
Video
Audio
Input Level
Video
Audio
Output Level
Video
Audio
Unclear picture display.
7.0"
Transparent type TN LCD
TFT active matrix
336,960 pcs. (1,440 x 234)
45dB
55dB
1 Vp-p (75Ω UNBALANCED)
500mV (RMS)
FR
1 Vp-p (75Ω UNBALANCED)
500mV (RMS)
14.4V DC (11-15 V allowable)
+32ºF to +113º(0ºC to + 45ºC)
2.0 kg (4 lbs. 7 oz)
0.2 kg (7 oz)
ES
CHASSIS SIZE (Monitor section)
Width
Height
Depth
178 mm (7")
50 mm (2")
165 mm (6-1/2")
DE
CHASSIS SIZE
(AV-Interface Unit section)
Width
Height
Depth
106.6 mm (4-1/4")
32 mm (1-1/4")
67.8 mm (2-11/16")
NOTES
• Due to continuous product improvement,
specifications and design are subject to change
without notice.
• The LCD panel is manufactured using an
extremely high precision manufacturing
technology. Its effective pixel ratio is over
99.99%. This means that there is a possibility
that 0.01% of the pixels could be either always
ON or OFF.
IT
SE
13-EN
Installation and Connections
Before installing or connecting the unit, please
read the following and pages 2 and 3 of this
manual thoroughly for proper use.
Warning
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
Failure to make the proper connections may result in fire
or product damage.
The wiring and installation of this unit requires special
technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to
have the work done.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.
USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY.
(Check with your dealer if you are not sure.) Failure to do
so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM
THE NEGATIVE BATTERY TERMINAL.
Be sure to use only the specified accessory parts. Use of
other than designated parts may damage this unit
internally or may not securely install the unit in place.
This may cause parts to become loose resulting in hazards
or product failure.
Failure to do so may result in electric shock or injury due
to electrical shorts.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
DO NOT ALLOW CABLES TO BECOME ENTANGLED
IN SURROUNDING OBJECTS.
Route the cables and wiring away from moving parts (like
the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes
through a hole in metal, use a rubber grommet to prevent
the wire’s insulation from being cut by the metal edge of
the hole.
MAKE THE CORRECT CONNECTIONS.
Arrange wiring and cables in compliance with the manual
to prevent obstructions when driving. Cables or wiring
that obstruct or hang up on places such as the steering
wheel, gear lever, brake pedals, etc. can be extremely
hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
DO NOT INSTALL IN LOCATIONS WITH HIGH
MOISTURE OR DUST.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
Avoid installing the unit in locations with high incidence
of moisture or dust. Moisture or dust that penetrates into
this unit may result in product failure.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or
any other safety-related system), or tanks should NEVER
be used for installations or ground connections. Using
such parts could disable control of the vehicle and cause
fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF
THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT
HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.
14-EN
Precautions
IMPORTANT
• Be sure to disconnect the cable from the (–) battery
post before installing your TME-M790. This will
reduce any chance of damage to the unit in case of a
short-circuit.
• Be sure to connect the color coded leads according to
the diagram. Incorrect connections may cause the unit
to malfunction or damage the vehicle's electrical
system.
• When making connections to the car’s electrical
system, be aware of the factory installed components
(e.g. on-board computer). Do not tap into these leads to
provide power for this unit. When connecting the
TME-M790 to the fuse box, make sure the fuse for the
intended circuit of the TME-M790 has the appropriate
amperage. Failure to do so may result in damage to the
unit and/or the vehicle. When in doubt, consult your
ALPINE dealer.
• The TME-M790 uses female RCA-type jacks for
connection to other units (e.g. amplifier) having RCA
connectors. You may need an adaptor to connect other
units. If so, please contact your authorized ALPINE
dealer for assistance.
• The Display must be completely retracted in the casing
when installing. If it is not, problems may occur.
• When installing in automobiles, make sure the Display
can open/close without coming in contact with the shift
lever.
Please record the serial number of your unit in
the space provided below and keep it as a
permanent record. The serial number plate is
located on the bottom of the unit.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
FR
ES
DE
IT
SE
15-EN
Installation and Connections
3
Installation
Installing the Monitor
Lock Pin
• Place of installation
Before determining the position of installation,
check that the display will not hamper gear
shifting when it is opened and closed in that
position.
NOTE
Install at an angle of within 30 degress from the
horizontal.
1
Dashboard
Mounting Sleeve
(Included)
Mounting Bracket
(Included)
Slide the TME-M790 into the dashboard. When
the unit is in place, make sure the locking pins
are fully seated in the down position. This can be
done by pressing firmly in on the unit while
pushing the locking pin down with a small
screwdriver. This ensures that the unit is properly
locked and will not accidentally come out from
the dashboard. Install the Supplied Front Frame.
Removal
1 Use a small screwdriver (or similar tool) to
push the locking pins to the “up” position (see
above drawing). As each pin is unlocked,
gently pull out on the unit to make sure it does
not re-lock before unlocking the second pin.
2 Pull the unit out, keeping it unlocked as you do
so.
TME-M790
Screws(M4x5)
(Included)
<JAPANESE CAR>
Slide mounting sleeve from main unit (see
Removal Procedure below). Slide the mounting
sleeve into the dashboard. Install the supplied
bracket to the monitor.
2
To install using the vehicle's genuine bracket
TME-M790
Ground Lead
Screws
(M4x5)
Screw
Metal Mounting Strap
Hex Nut
(M5)
Bolt Stud
TME-M790
Ground Lead
Chassis
Front Frame
(Included)
Reinforce the monitor with the metal mounting
strap (not supplied). Secure the ground lead of
the unit to a clean metal spot using a screw ( )
already attached to the vehicle’s chassis.
NOTE
For the screw marked
, use an appropriate
screw for the chosen mounting location.
16-EN
Mounting Bracket
Attaching the AV-Interface Unit
When attaching with VelcroTM Tape, be sure to
choose a level location.
Do not attach in a location where the AVInterface unit is upside down.
Attach the AV-Interface Unit.
Attach the VelcroTM Tape included with the AVInterface Unit and secure the unit under the
passenger seat, for example.
EO
VID
IO
R
AU
D
AU
X
(MO INP
L NO) UT 1
EO
VID
AU
X
(MO INP
U
L NO) T 2
IO
AU
D
ATIO
R
NA
VIG
N
R
AU
D
IO
AU
X
L
OU
UT
O
AY
T
PU
UT
TP
PL
DIS
VID
EO
VelcroTM Tape (Included)
FR
Foot Brake Lead/Parking Brake Lead Connection
If necessary, use a pinch connector to connect the foot brake lead, parking brake lead, etc.
1
Vehicle Cable
2
Pinch Connector
Plier
Monitor Cable
Stopper
ES
Foot brake lamp
FOOT BRAKE
(Yellow/Black)
TME-M790
Pinch Connector
Foot brake switch
Foot brake lead
Chassis
Parking brake lamp
PARKING BRAKE
Battery
(Yellow/Blue)
Pinch Connector
Parking brake lead
DE
Parking brake switch
Connection Diagram of SPST Switch (Sold Separately)
(If the ACC power supply is not available)
SPST SW (Optional)
IGNITION
IT
(Red)
BATTERY
TME-M790
(Monitor)
(Yellow)
Battery
NOTE
If your vehicle has no ACC power supply, add an SPST
(Single-Pole, Single-Throw) switch (sold separately).
If the switched power (ignition) lead of the TMEM790 is connected directly to the positive (+) post of
the vehicle’s battery, the TME-M790 draws some
current (several hundred milliamperes) even when its
switch is placed in the OFF position and the battery
may be discharged.
SE
17-EN
Installation and Connections
Connections
White/Brown
REMOTE OUT
AUX1
1
White/Brown
REMOTE OUT
AUX2
1
Yellow/Black
FOOT BRAKE
2
Yellow/Blue
PARKING BRAKE
3
Pink/Black
AUDIO
INTERRUPT OUT
4
Red
IGNITION
5
Yellow
BATTERY
6
Black
GND
7
To remote input lead.
To remote input lead.
To the foot brake cord or brake lamp cord.
8
To the parking brake signal lead.
Connect to an IN INT compatible product.
Ignition key
Battery
NAVIGATION
R
AUDIO
L
8
VIDEO
AUX OUTPUT
DISPLAY OUTPUT
Monitor
R
1 Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input
lead. This lead outputs the controlling signals
from the remote control.
2 Foot Brake Lead (Yellow/Black)
Connect to the vehicle’s foot brake lead or brake
lamp lead.
3 Parking Brake Lead (Yellow/Blue)
Connect this lead to the power supply side of the
parking brake switch to transmit the parking
brake status signals to the TME-M790.
4 Audio Interrupt Out Lead (Pink/Black)
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the
vehicle’s fuse box or another unused power
source which provides (+) 12V only when the
ignition is turned on or in the accessory position.
6 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the
vehicle’s battery.
18-EN
AUX INPUT 2
(MONO)
L
AUDIO
VIDEO
R
AUX INPUT 1
(MONO)
L
AUDIO
VIDEO
7 Ground Lead (Black)
Connect this lead to a good chassis ground on
the vehicle. Make sure the connection is made to
bare metal and is securely fastened using the
sheet metal screw provided.
8 Fuse Holder (5A)
To prevent external noise from entering the
audio system.
• Locate the unit and route the leads at least
10cm away from the car harness.
• Keep the battery power leads as far away from
other leads as possible.
• Connect the ground lead securely to a bare
metal spot (remove the coating if necessary) of
the car chassis.
• If you add an optional noise suppressor,
connect it as far away from the unit as possible.
Your Alpine dealer carries various Alpine noise
suppressors, contact them for further
information.
• Your Alpine dealer knows best about noise
prevention measures so consult your dealer for
further information.
System Connections
1
6
DVD Player
DVA-5205
7
(Sold separately)
2
REMOTE IN
REMOTE OUT
AUX1
(White/Brown)
(White/Brown)
3
TV Tuner
(Sold separately)
Color Control
ON
OFF
KCE-150V
(Sold separately)
8
REMOTE IN
REMOTE OUT
AUX2
(White/Brown)
(White/Brown)
R
AUDIO
AUX INPUT 2
(MONO)
L
VIDEO
R
AUDIO
AUX INPUT 1
(MONO)
L
VIDEO
DISPLAY OUTPUT
FR
Monitor
NOTE
When the DVA-5200 is connected for the DVD
Player, use the Ai-NET-PIN connection cord
KCA-120B (sold separately).
AUX OUTPUT
NAVIGATION
R
AUDIO
L
VIDEO
AV-Interface unit
ES
4
5
Rear
Monitor
(Sold separately)
9
10
DE
Navigation
System
(Sold separately)
(NVE-N851A/NVE-N871A)
1 RCA Extension Cable (Included with DVD
2
3
4
5
6
Player)
RCA Extension Cable (Option)
RCA Extension Cable (Included with KCE150V)
RCA Extension Cable (Option)
RGB Cable (Navigation NVE-N851A: Included,
Navigation NVE-N871A: Sold separately)
Video Output Connector
Connect the AUX INPUT 1, Video Input Terminal
on the TME-M790 to the Video Output Connector
on the DVD player.
7 Audio Output Connector
Connect the AUX INPUT 1, Audio Input Terminal
on the TME-M790 to the Audio Output Connector
(L/R) on the DVD player.
8 Video Output Terminal
Connect the AUX INPUT 2 Terminal on the TMEM790 to the Video Output Terminal.
IT
9 AUX Input Terminal
Connect the AUX OUTPUT Terminal on the TMEM790 to the AUX Input Terminal.
p RGB Output Connector
Connect the NAVIGATION RGB Connector on
the TME-M790 to the RGB Output Connector on
the navigation system.
NOTES
• When this product is used in combination with a
separately sold Ai-NET-PIN connection cord (KCA121B), the sound can be output to a head unit
equipped with an external input. For details, refer to
the head unit’s operating instructions.
• When the NVA-N751AS is connected for the
Navigation System, use the RGB conversion cable
KWE-503N (sold separately).
19-EN
SE
GARANTIE LIMITÉE
Fidèles à leur engagement de ne fournir que des produits de qualité, ALPINE ELECTRONIQUE DE L'AMERIQUE INC. et
ALPINE ELECTRONIQUE DU CANADA INC. (Alpine) sont heureuses de vous offrir cette garantie. Nous vous suggérons de le
lire attentivement et en entier. Si vous avez la moindre question, veuillez contacter l'un de nos concessionnaires ou appeler
directement Alpine au numéros Liste ci-dessous.
● PRODUITS COUVERT PAR LA GARANTIE
Cette garantie couvre les produits audio/visuel de voiture et
les accessoires connexes ("le produit"). Elle ne couvre les
produits que dans le pays où il ont été achetés.
2 Vous devez donner une description détaillée des
problèmes qui sont à l'origine de votre demande de
réparation.
Vous devez joindre la preuve de votre achat du produit.
Vous devez emballer soigneusement le produit pour éviter
tout dommage durant son transport.
● DURÉE DE LA GARANTIE
3
4
Cette garantie est en vigueur pendant un an à partir de la date
du premier achat du client.
● LIMITATION DES GARANTIES TACITES
Toutes les têtes de cassettes analogiques audio de voiture
Alpine, à l’exception des êtes de cassettes vidéo sont
garanties à vie contre des vices de fabrication pouvant
entraîner leur panne.
LA DURÉE DE TOUTES LES GARANTIES TACITES, Y
COMPRIS LA GARANTIE D'ADAPTATION A L'UTILISATION
ET LA GARANTIE DE QUALITÉ LOYALE ET MARCHANDE,
EST LIMITÉE À CELLE DE LA GARANTIE EXPRESSE
DÉTERMINÉE CI-DESSUS. PERSONNE N'EST AUTORISÉ
À ENGAGER AUTREMENT LA RESPONSABILITÉ D'ALPINE
EN VERTU DE LA VENTE D'UN PRODUIT.
● PERSONNES PROTÉGÉES PAR LA GARANTIE
● EXCLUSIONS DE LA GARANTIE
Seul l'acheteur original du produit, s'il résisde aux États-Unis,
à Porto Rico ou au Canada, peut se prévaloir de la garantie.
ALPINE STIPULE EXPRESSÉMENT QU'ELLE N'EST PAS
RESPONSABLE DES DOMMAGES DOMMAGES-INTÉRÊTS
ET DOMMAGES INDIRECTS PROVOQUÉS PAR LE
PRODUIT. LES DOMMAGES DOMMAGES-INTÉRÊTS
SONT LES FRAIS DE TRANSPORT DU PRODUIT VERS UN
CENTRE DE SERVICE ALPINE, LA PERTE DE TEMPS DE
L'ACHETEUR ORIGINAL, LA PERTE D'UTILISATION DU
PRODUIT, LES BILLETS D'AUTOBUS, LA LOCATION DE
VOITURES ET TOUS LES AUTRES FRAIS LIÉS À LA
GARDE DU PRODUIT.
LES DOMMAGES INDIRECTS SONT LES FRAIS DE
RÉPARATION OU DE REMPLACEMENT D'AUTRES BIENS
ENDOMMAGÉS SUITE AU MAUVAIS FONCTIONNEMENT
DU PRODUIT.
LES RECOURS PRÉVUS PAR LES PRÉSENTES
EXCLUENT ET REMPLACENT TOUTE AUTRE FORME DE
RECOURS.
● GARANTIE À VIE DES TÊTES DE LECTURE DES
MAGNÉTOPHONES À CASSETTES
● CE QUI EST COUVERT
Cette garantie couvre tous les défauts de matériaux et de
fabrication (pièces et main d'œuvre) du produit.
● CE QUI N'EST PAS COUVERT
1
Cette garantie ne couvre pas ce qui suit:
Les dommages survenus durant le transport des produits
renvoyés à Alpine pour être réparés (les réclamations
doivent être adressées au transporteur);
Tout dégât provoqué par accident, abus, négligence,
usage inapproprié, mauvais raccordement, mauvaise
utilisation ou par le non-respect des instructions
indiquées dans le manuel de l’utilisateur.
Les dommages dus à la force majeure, notamment aux
tremblements de terre, au feu, aux inondations, aux
tempêtes ou aux autres cataclysmes naturels;
Les frais ou les dépenses relatifs à l'enlèvement ou à la
réinstallation du produit;
Les services rendus par une personne, physique ou
morale non autorisée;
Les produits dont le numéro de série a été effacé, modifié
ou retiré;
Les produits qui ont été adaptés ou modifiés sans le
consentement d'Alpine;
Les produits qui ne sont pas distribués par Alpine aux
Etats-Unis, à Porto Rico ou au Canada;
Les produits qui n'ont pas été achetés par l'entremise d'un
concessionnaire Alpine autorisé;
Tout produit qui a été déterminé comme contenant une
quantité excessive de poussière ou de saleté et tout
produit qui contient d’autres saleté, en ce compris du
liquide et des corps étrangers.
2
3
4
5
6
7
8
9
Ä
● LIEN ENTRE LA GARANTIE ET LA LOI
La garantie vous donne des droits spécifiques, mais vous
pouvez aussi jouir d'autres droits, qui varient d'un état ou
d'une province à l'autre. En outre, certains états et certaines
provinces interdisent de limiter la durée des garanties tacites
ou d'exclure les dommages accessoires ou indirects. Dans ce
cas, les limites et les exclusions de la garantie peuvent ne pas
s'appliquer à vous.
● CLAUSE APPLICABLE AU CANADA SEULEMENT
Pour que la garantie soit valable, il faut qu'un centre
d'installation autorisé ait installé le système audio pour l'auto
dans votre véhicule et qu'il ait ensuite apposé son cachet sur
la garantie.
● NUMÉROS D'APPEL DU SERVICE À LA CLIENTELE
Si vous avez besoin de nos services, veuillez appeler le
centre de service autorisé Alpine le plus proche.
● COMMENT SE PRÉVALOIR DE LA GARANTIE
1 Il vous faut remettre le produit nécessitant des réparations
à un centre de service autorisé Alpine ou à Alpine même et
en assumer les frais de transport. Alpine a le choix entre
réparer le produit ou le remplacer par un produit neuf ou
révisé, le tout sans frais pour vous. Si les réparations sont
couvertes par la garantie et si le produit a été envoyé à un
centre de service Alpine ou à Alpine, le paiement des frais
de réexpédition du produit incombe Alpine.
U.S.A.
CANADA
1-800-ALPINE-1 (1-800-257-4631)
1-800-ALPINE-1 (1-800-257-4631)
Alpine Électronique de L'Amérique, Inc., 19145 Gramercy Place, Torrance, California 90501, U.S.A.
Alpine Électronique du Canada, Inc., Suite 203, 7300 Warden Ave. Markham, Ontario L3R 9Z6, Canada
LIMITED WARRANTY
ALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality
craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any
questions, please contact your Dealer or Alpine at one of the telephone numbers listed below.
● PRODUCTS COVERED:
This Warranty covers Car Audio/Visual Products and
Related Accessories ("the product"). Products purchased in
the Canada are covered only in the Canada. Products
purchased in the U.S.A. are covered only in the U.S.A.
2 You should provide a detailed description of the
problem(s) for which service is required.
3 You must supply proof of your purchase of the product.
4 You must package the product securely to avoid
damage during shipment.
● LENGTH OF WARRANTY:
● HOW WE LIMIT IMPLIED WARRANTIES:
This Warranty is in effect for one year from the date of the
first consumer purchase.
All Alpine Car Audio analog tape heads excluding Video
tape heads are warranted for life against manufacturing
defects causing failure.
ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR
USE AND MERCHANTABILITY ARE LIMITED IN
DURATION TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE AND NO PERSON IS
AUTHORIZED TO ASSUME FOR ALPINE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT.
● WHO IS COVERED:
● HOW WE EXCLUDE CERTAIN DAMAGES:
This Warranty only covers the original purchaser of the
product, who must reside in the United States, Puerto Rico
or Canada.
ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR
INCIDENTAL AND CONSEQUENTIAL DAMAGES
CAUSED BY THE PRODUCT. THE TERM "INCIDENTAL
DAMAGES" REFERS TO EXPENSES OF
TRANSPORTING THE PRODUCT TO THE ALPINE
SERVICE CENTER, LOSS OF THE ORIGINAL
PURCHASER'S TIME, LOSS OF THE USE OF THE
PRODUCT, BUS FARES, CAR RENTALS OR OTHERS
COSTS RELATING TO THE CARE AND CUSTODY OF
THE PRODUCT. THE TERM "CONSEQUENTIAL
DAMAGES" REFERS TO THE COST OF REPAIRING OR
REPLACING OTHER PROPERTY WHICH IS DAMAGED
WHEN THIS PRODUCT DOES NOT WORK PROPERLY.
THE REMEDIES PROVIDED UNDER THIS WARRANTY
ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.
● LIFETIME TAPE HEAD WARRANTY:
● WHAT IS COVERED:
This Warranty covers defects in materials or workmanship
(parts and labor) in the product.
● WHAT IS NOT COVERED:
1
This Warranty does not cover the following:
Damage occurring during shipment of the product to
Alpine for repair (claims must be presented to the
carrier).
Damage caused by accident, abuse, negligence,
misuse, improper connections, improper operation or
failure to follow instructions contained in the Owner's
manual.
Damage caused by act of God, including without
limitation, earthquake, fire, flood, storms or other acts of
nature.
Any cost or expense related to the removal or
reinstallation of the product.
Service performed by an unauthorized person, company
or association.
Any product which has the serial number defaced,
altered or removed.
Any product which has been adjusted, altered or
modified without Alpine's consent.
Any product not distributed by Alpine within the United
States, Puerto Rico or Canada.
Any product not purchased from an Authorized Alpine
Dealer.
Any product that has been determined to contain an
excessive amount of dust or dirt and any product that
contains other contaminants including liquid or foreign
objects.
2
3
4
5
6
7
8
9
Ä
● HOW TO OBTAIN WARRANTY SERVICE:
1 You are responsible for delivery of the product to an
● HOW STATE/PROVINCIAL LAW RELATES TO THE
WARRANTY:
This Warranty gives you specific legal rights, and you may
also have other rights which vary form state to state and
province to province. In addition, some states/provinces do
not allow limitations on how long an implied warranty lasts,
and some do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly,
limitations as to these matters contained herein may not
apply to you.
● IN CANADA ONLY:
This Warranty is not valid unless your Alpine car audio
product has been installed in your vehicle by an Authorized
Installation Center, and this warranty stamped upon
installation by the installation center.
● HOW TO CONTACT CUSTOMER SERVICE:
Should the product require service, please call the following
number for your nearest Authorized Alpine Service Center.
U.S.A.
CANADA
1-800-ALPINE-1 (1-800-257-4631)
1-800-ALPINE-1 (1-800-257-4631)
Authorized Alpine Service Center or Alpine for repair
and for payment of any initial shipping charges. Alpine
will, at its option, repair or replace the product with a
new or reconditioned product without charge. If the
repairs are covered by the warranty, and if the product
was shipped to an Authorized Alpine Service Center or
Alpine, Alpine will pay the return shipping charges.
Alpine Electronics of America, Inc., 19145 Gramercy Place, Torrance, California 90501, U.S.A.
Alpine Electronics of Canada, Inc., Suite 203, 7300 Warden Ave. Markham, Ontario, L3R 9Z6, Canada
Download PDF

advertising