Specifications | Alto-Shaam 10.10 Oven User Manual

Combination
Oven / Steamer
ES ELECTRIC
S ERI ES
6•10
10•10
7•14
10•18
12•20
20•20
VH ES-5
VH ES-10
I N STALLATION
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE:
PRINTED IN U . S . A .
262.251.3800 • 800.558.8744
USA / CANADA
FAX:
WWW. ALTO - SHAAM . COM
262.251.7067 • 800.329.8744 U . S . A .
ONLY
#MN-28677 • 08/08
General Information
Delivery / Unpacking . . . . . . . . . . . . . . . . . .1.
Safety Procedures and Precautions . . . . . . . . .2.
Specifications
Options . . . . . . . . . . . . . . . . . . . . . . . . . . .3.
6•10es . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.
6•10esi
. . . . . . . . . . . . . . . . . . . . . . . . . . .5.
6•10esiN . . . . . . . . . . . . . . . . . . . . . . . . . .6.
10•10es . . . . . . . . . . . . . . . . . . . . . . . . . . .7.
10•10esi
. . . . . . . . . . . . . . . . . . . . . . . . . .8.
10•10esiN . . . . . . . . . . . . . . . . . . . . . . . . .9.
7•14es . . . . . . . . . . . . . . . . . . . . . . . . . . .10.
7•14esi
. . . . . . . . . . . . . . . . . . . . . . . . . .11.
10•18es . . . . . . . . . . . . . . . . . . . . . . . . . .12.
10•18esi
. . . . . . . . . . . . . . . . . . . . . . . . .13.
12•20es . . . . . . . . . . . . . . . . . . . . . . . . . .14.
20•20es . . . . . . . . . . . . . . . . . . . . . . . . . .15.
Installation Requirements
Installation Codes & Standards . . . . . . . . . . .16.
Ventilation General Requirements . . . . . . . . .17.
Positioning on Site . . . . . . . . . . . . . . . . . . .17.
Minimum Clearance Requirements
Positioning Requirements
. . . . . . . .17.
. . . . . . . . . . . . . .18.
Electrical Requirements . . . . . . . . . . . . . . . .19.
Drip Tray Installation . . . . . . . . . . . . . . . . .20.
Mobile Equipment Restraint . . . . . . . . . . . . .20.
Water Quality Requirements . . . . . . . . . . . . .21.
Water Connection
. . . . . . . . . . . . . . . . . . .22.
Water Filtration System . . . . . . . . . . . . . . . .23.
Water Drainage . . . . . . . . . . . . . . . . . . . . .24.
Installation Checklist . . . . . . . . . . . . . . . . .25.
Error Codes
Control Reset
. . . . . . . . . . . . . . . . . . . . . .26.
Service Mode and Error Codes . . . . . . . . . . .26.
Emergency Operation . . . . . . . . . . . . . . . . .29.
Ventless Hood Option
Condensate Drain . . . . . . . . . . . . . . . . . . . .30.
Opening Mechanism . . . . . . . . . . . . . . . . . .30.
Operation . . . . . . . . . . . . . . . . . . . . . . . . .31.
Interlock Switches
. . . . . . . . . . . . . . . . . . .31.
Reset Switch . . . . . . . . . . . . . . . . . . . . . . .31.
Cleaning and Maintenance . . . . . . . . . . . . . .32.
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . .32.
Equipment Limited Warranty
. . . . . . . . . . .33.
Transportation Damage and Claims . . . . . .34.
®
DELIVERY
U N PA C K I N G
This Alto-Shaam appliance has been
thoroughly tested and inspected to insure only the
highest quality unit is provided. Upon receipt,
check for any possible shipping damage and report
it at once to the delivering carrier. See
Transportation Damage and Claims section
located in this manual.
This appliance, complete with unattached
items and accessories, may have been delivered in
one or more packages. Check to ensure that all
standard items and options have been received
with each model as ordered.
Save all the information and instructions
packed with the appliance. Complete and return
the warranty card to the factory as soon as
possible to assure prompt service in the event of a
warranty parts and labor claim.
This manual must be read and understood by
all people using or installing the equipment
model. Contact the Alto-Shaam service
department if you have any questions concerning
installation, operation, or maintenance.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
1. Carefully remove the
appliance from the
carton or crate.
NOTE: Do not discard the
carton and other
packaging material
until you have
inspected the unit
for hidden damage
and tested it for
proper operation.
®
®
2. Read all instructions in this manual carefully
before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner or
manager of the business or to the person
responsible for training operators. Additional
manuals are available from the Alto-Shaam
service department.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
CAUTION
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
THE INFORMATION CONTAINED IN THIS
MANUAL IS IMPORTANT FOR THE PROPER
INSTALLATION OF THIS OVEN. PLEASE
READ CAREFULLY AND RETAIN FOR
FUTURE REFERENCE.
LES INFORMATIONS CONTENUES DANS CE
MANUEL SONT IMPORTANTES POUR
L'INSTALLATION L'UTILISATION ET
L'ENTRETIEND DE CE FOUR. S'IL VOUS
PLAIT LISEZ-LE TRES ATTENTIVEMENT ET
CONSERVEZ-LE.
IMPROPER CONNECTION OF THIS
APPLIANCE WILL NULLIFY ALL
WARRANTIES.
LA NON-APPLICATION DE CES CONSIGNES
ANNULE TOUTES GARANTIES.
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
1
SAFETY PROCEDURES
AND PRECAUTIONS
Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.
DANGER
Used to indicate the presence of a
hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.
WA R N I N G
Used to indicate the presence of a
hazard that CAN cause personal injury,
possible death, or major property
damage if the warning included with
this symbol is ignored.
1. This appliance is intended to cook, hold or
process foods for the purpose of human
consumption. No other use for this appliance is
authorized or recommended.
2. This appliance is intended for use in commercial
establishments where all operators are familiar
with the purpose, limitations, and associated
hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
3. Any troubleshooting guides, component views,
and parts lists included in this manual are for
general reference only and are intended for use
by qualified technical personnel.
4. This manual should be considered a permanent
part of this appliance. This manual and all
supplied instructions, diagrams, schematics,
parts lists, notices, and labels must remain with
the appliance if the item is sold or moved to
another location.
CAUTION
Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.
NOTE
For equipment delivered for use
in any location regulated by the
following directive:
DO NOT DISPOSE OF ELECTIRCAL
OR ELECTRONIC EQUIPMENT WITH
OTHER MUNICIPAL WASTE.
CAUTION
Used to indicate the presence of a hazard that can
or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.
CAUTION
N O T E : Used to notify personnel of
WHEN WELDING ANY STAINLESS
STEEL COMPONENTS ON THIS
APPLIANCE, THE ELECTRONIC
CONTROL BOARDS MUST BE
ISOLATED FROM THE APPLIANCE.
installation, operation, or
maintenance information that is
important but not hazard related.
ELECTRIC COMBITHERM
PG .
2
—
INSTALLATION MANUAL
#MN-28677
C O M M O N S P E C I F I C AT I O N S
®
COMBITHERM
■ CombiGuard™ Triple-Guard Water Filtration System
( INCLUDES 1
CARTRIDGE )
FI-23014
■ CombiGuard™ Replacement Filter
■ Fry Basket, 12"
■ Grilling Grate,
12"
X
X
FI-26356
20" (325mm x 530mm)
BS-26730
20" (325mm x 530mm)
SH-26731
■ Oven Cleaner —
SPECIALLY FORMULATED FOR COMBITHERM OVENS
TWELVE
(12)
■ Scale Free™
➥
( CITRUS
CASE
=
CONTAINERS / CASE ,
1
QUART ( C .
1
CE-24750
LITER ) EACH
BASED , NON - CORROSIVE DELIMING PRODUCT )
FOUR
4- LB
BOTTLES ;
4- LB
■ Service Start-Up Check
BOTTLE MAKES
10
CE-27889
Six (6) Chicken Roasting Rack
( PAN NOT INCLUDED )
SH-23000
GALLONS
SPECIFY AS REQUIRED
AVAILABLE THROUGH AN ALTO - SHAAM FASTEAM CENTER
5005676
■ Computer Software Options
Not available on S-Control Models .
REFER TO HACCP SPECIFICATION SHEET
FOR APPLICABLE PART NUMBERS
#9015
Ten (10) Chicken Roasting Rack
SH-22634
■ HACCP Documentation
■ HACCP Documentation with Kitchen Management
■ Wireless HACCP Documentation with
Kitchen Management
Fry Basket BS-26730
IEEE 802.11b STANDARDS
Grilling Grate SH-26731
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
3
6 • 1 0 ES S P E C I F I C A T I O N S
®
COMBITHERM
30" (761mm)
2" (50mm)
49-1/8" (1247mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
4-15/16"
(125mm)
33-1/8" (840mm)
6-3/8" (161mm)
35-3/16" (893mm)
27-11/16"
(702mm)
7-9/16"
(192mm)
60-9/16" (1538mm)
Steam Vent (Top)
(290mm)
14-3/16"
(360mm)
11-7/16"
15-7/8"
(403mm)
Decalcification
Port
Untreated Water
Intake (Bottom)
Treated Water
Intake (Bottom)
Electrical Connection
(Bottom)
34-1/16" (864mm)
31-3/8" (796mm)
43-7/8" (1114mm)
41-15/16" (1064mm)
Water Drain
(Side Back)
2-3/16" (56mm)
4-3/4" (120mm)
7-9/16"
(191mm)
WATER
DRAIN
17-15/16"
(456mm)
DIMENSIONS: H x W x D
EXTERIOR :
35-3/16" x 43-7/8" x 34-1/16" (893mm x 1114mm x 864mm)
EXTERIOR WITH RETRACTABLE DOOR :
35-3/16" x 47-7/8" x 34-1/16" (893mm x 1216mm x 864mm)
INTERIOR :
17-3/4" x 23-1/2" x 21-1/16" (450mm x 597mm x 535mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
440-480 380-4 15 208-240 208-240
ELECTRICAL
VOLTAGE
at 208
at 240
PHASE
CYCLE/HZ
at 208
at 240
3
50/60
at 380
at 415
3
50/60
at 440
at 480
3*
50/60
1*
*
50/60
SHIP
CRATE
DIMENSIONS :
2 Wire plus ground
AWG 6
4
40.5
47.0
3 Wire plus ground
AWG 8
23.5/ph
27.0/ph
3 Wire plus ground
AWG 8
20.0/ph
22.0/ph
4 Wire plus ground
AWG 12
C A PA C I T Y
360 lb
484 lb
40"
(163 kg)
X
48"
X
(220 kg)
40"
EST .
(1016 x 1219 x 1016mm)
FULL-SIZE PANS:
GN 1/1:
HALF-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
8.4
11.2
8.4
11.2
13.0/ph
16.0/ph
20" x 12" x 2-1/2"
530 x 325 x 65mm
18" x 13" x 1"
8.4
11.2
15.4
18.4
72 lb (33 kg)
VOLUME MAXIMUM :
45
Six (6)
Six (6)
Six (6)
MAXIMUM
QUARTS
(57
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
PG .
kW
AMPS
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
NET
AWG
—
INSTALLATION MANUAL
#MN-28677
LITERS )
6 • 1 0 ES i S P E C I F I C A T I O N S
®
COMBITHERM
30" (761mm)
2" (50mm)
49-1/8" (1247mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
4-15/16"
(125mm)
33-1/8" (840mm)
6•10ESi
440-480 380-415 208-240 208-240
VOLTAGE
CYCLE/HZ
PHASE
at 208
1*
at 240
at 208
50/60
3
at 240
at 380
at 440
*
AMPS
AWG 6
47.0
3 Wire plus ground
23.3/ph
AWG 12
15.6/ph
50/60
40"
(156 kg)
X
48"
X
8.4
13.0/ph
3 Wire plus ground
48.0
11.7
15.4
21.0/ph
18.4
9.0
25.0/ph
28.2/ph
8.5
22.0/ph
kW
43.3
11.2
11.2
20.0/ph
AWG 8
C A PA C I T Y
467 lb
11.2
AMPS
14.0/ph
16.3/ph
23.0/ph
9.0
11.7
9.0
11.7
15.9
18.9
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
343 lb
8.5
27.0/ph
4 Wire plus ground
6•10ESi/sk
kW
41.0
AWG 8
50/60
3*
at 480
AWG
2 Wire plus ground
50/60
3
at 415
DIMENSIONS :
6-3/8" (161mm)
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
ELECTRICAL
CRATE
17-15/16"
(456mm)
7-9/16"
(191mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
RIGHT : 4" (102mm)
TOP : 20" (508mm) FOR AIR MOVEMENT
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
SHIP
WATER
DRAIN
DIMENSIONS: H x W x D
EXTERIOR :
35-3/16" x 43-7/8" x 34-1/16" (893mm x 1114mm x 864mm)
EXTERIOR WITH RETRACTABLE DOOR :
35-3/16" x 47-7/8" x 34-1/16" (893mm x 1216mm x 864mm)
INTERIOR :
17-3/4" x 23-1/2" x 21-1/16" (450mm x 597mm x 535mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
NET
35-3/16" (893mm)
27-11/16"
(702mm)
7-9/16"
(192mm)
Steam Vent (Top)
Electrical Connection (Bottom)
60-9/16" (1538mm)
11-7/16"
(290mm)
14-3/16"
(360mm)
15-7/8"
(403mm)
Untreated Water
Intake (Bottom)
Low Pressure
Treated Water Valve (Top)
Intake (Bottom)
34-1/16" (864mm)
31-3/8" (796mm)
43-7/8" (1114mm)
41-15/16" (1064mm)
Water Drain
(Side Back)
2-3/16" (56mm)
4-3/4" (120mm)
(212 kg)
40"
EST .
(1016 x 1219 x 1016mm)
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
HALF-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
18" x 13" x 1"
VOLUME
72 lb (33 kg)
MAXIMUM : 45
Six (6)
Six (6)
Six (6)
MAXIMUM
QUARTS
(57
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
Four (4)
Four (4)
Five (5)
LITERS )
#MN-28677
PG .
5
6 • 1 0 ES iN S P E C I F I C A T I O N S
®
COMBITHERM
21-7/8"
(555mm)
Water Drain
(Side Back)
2" (50mm)
41-1/16" (1042mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
5"
(126mm)
25"
(635mm)
6•10ESiN
440-480 380-415 208-240 208-240
VOLTAGE
CYCLE/HZ
PHASE
at 208
1*
at 240
at 208
50/60
3
at 240
at 380
at 440
*
472 lb
40"
37"
X
6
3 Wire plus ground
23.3/ph
AWG 12
15.6/ph
27.0/ph
13.0/ph
3 Wire plus ground
20.0/ph
AWG 8
(214 kg)
40"
EST .
(1016 x 940 x 1016mm)
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
HALF-SIZE PANS:
GN 1/2:
HALF-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
22.0/ph
20" x 12" x 2-1/2"
530 x 325 x 65mm
10" x 12" x 2-1/2"
265 x 325 x 65mm
18" x 13" x 1"
11.2
8.4
kW
48.0
11.7
43.3
25.0/ph
11.2
28.2/ph
15.4
21.0/ph
8.5
11.2
18.4
72 lb (33 kg)
45
VOLUME MAXIMUM :
Six (6)
Six (6)
Twelve (12)
Twelve (12)
Six (6)
MAXIMUM
QUARTS
(57
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
PG .
47.0
8.5
6•10ESiN/sk
AMPS
14.0/ph
16.3/ph
23.0/ph
9.0
9.0
11.7
9.0
11.7
15.9
18.9
ELECTRICAL SERVICE CHARGE APPLIES
(158 kg)
X
AWG 6
kW
41.0
4 Wire plus ground
50/60
WEIGHT
348 lb
AMPS
AWG 8
50/60
3*
at 480
AWG
2 Wire plus ground
50/60
3
at 415
DIMENSIONS :
19-9/16"
(496mm)
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
ELECTRICAL
CRATE
7-1/2"
(190mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
SHIP
WATER
DRAIN
DIMENSIONS: H x W x D
EXTERIOR :
35-3/16" x 35-13/16" x 35-9/16" (893mm x 909mm x 903mm)
EXTERIOR WITH RETRACTABLE DOOR :
35-3/16" x 39-13/16" x 35-9/16" (893mm x 1011mm x 903mm)
INTERIOR :
17-3/4" x 13-1/4" x 26-1/4" (450mm x 387mm x 665mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
NET
6-3/8" (161mm)
35-3/16" (893mm)
26-3/4"
(679mm)
Steam Vent
(Top)
7-9/16"
(192mm)
Untreated Water
Intake (Bottom)
Low Pressure
Valve
Treated Water
Intake (Bottom)
Electrical Connection
(Bottom)
35-9/16" (903mm)
32-15/16" (835mm)
35-13/16" (909mm)
33-7/8" (859mm)
54-1/8" (1374mm)
(242mm)
12-5/16"
(312mm)
9-9/16"
19-1/2"
(495mm)
2-3/16" (55mm)
4-3/4" (120mm)
—
INSTALLATION MANUAL
#MN-28677
LITERS )
Four (4)
Four (4)
Eleven (11)
Eleven (11)
Five (5)
1 0 • 1 0 ES S P E C I F I C A T I O N S
®
COMBITHERM
30" (761mm)
Water Drain
(Back Side)
2" (50mm)
33-1/16" (840mm)
46-7/8" (1190mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
PHASE
CYCLE/HZ
at 208
at 240
3
50/60
3
50/60
at 440
at 480
3*
50/60
440-480 380-415 208-240 208-240
at 208
at 240
1*
at 380
at 415
*
NET
SHIP
CRATE
DIMENSIONS :
528 lb
49"
(183 kg)
X
47"
X
(239 kg)
37"
EST .
(1245 x 1194 x 940mm)
67.0
77.0
3 Wire plus ground
AWG 6
38.5/ph
44.0/ph
3 Wire plus ground
AWG 8
20.0/ph
22.0/ph
4 Wire plus ground
AWG 10
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
HALF-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
20" x 12" x 2-1/2"
530 x 325 x 65mm
18" x 13" x 1"
120 lb (54 kg)
VOLUME MAXIMUM :
—
INSTALLATION MANUAL
13.9
18.4
13.8
18.3
21.5/ph
25.6/ph
75
MAXIMUM
QUARTS
14.2
18.4
15.4
18.4
Ten (10)
Ten (10)
Ten (10)
(95
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
kW
AMPS
2 Wire plus ground
AWG 3
ELECTRICAL SERVICE CHARGE APPLIES
404 lb
17-15/16"
(456mm)
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
AWG
50/60
WEIGHT
7-9/16"
(191mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
VOLTAGE
4-15/16"
(125mm)
Water Drain
DIMENSIONS: H x W x D
EXTERIOR :
41-1/2" x 43-7/8" x 34-1/16" (1053mm x 1114mm x 865mm)
EXTERIOR WITH RETRACTABLE DOOR :
41-1/2" x 47-7/8" x 34-1/16" (1053mm x 1216mm x 865mm)
INTERIOR :
27" x 23-1/2" x 21-1/16" (685mm x 597mm x 535mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
ELECTRICAL
6-1/4" (158mm)
Electrical Connection (Bottom)
31-3/8" (796mm)
41-1/2" (1053mm)
Treated Water
Intake (Bottom)
34-1/16" (865mm)
33-15/16" (861mm)
Untreated Water
Intake (Bottom)
43-7/8" (1114mm)
41-15/16" (1064mm)
7-9/16" (192mm)
Steam Vent (Top)
Decalcification
Port
11-7/16"
(290mm)
15-7/8"
(403mm)
14-3/16"
(360mm)
4-3/4" (120mm)
60-9/16" (1538mm)
3-3/16" (80mm)
LITERS )
#MN-28677
PG .
7
1 0 • 1 0 ES i S P E C I F I C A T I O N S
®
COMBITHERM
30" (761mm)
2" (50mm)
33-1/16" (840mm)
46-7/8" (1190mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
4-15/16"
(125mm)
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
ELECTRICAL
10•10ESi
208
240
208
240
380
415
440
480
440-480 380-415 208-240 208-240
VOLTAGE
PHASE
1*
CYCLE/HZ
3
3
50/60
50/60
50/60
3*
SHIP
CRATE
DIMENSIONS :
2 Wire plus ground
AWG 3
3 Wire plus ground
AWG 6
4 Wire plus ground
AWG 10
3 Wire plus ground
AWG 8
8
AMPS
kW
13.9
18.4
13.9
18.4
13.9
18.4
15.4
18.4
10•10ESi/sk
69.2
79.0
40.0/ph
45.5/ph
22.0/ph
26.3/ph
21.0/ph
23.0/ph
AMPS
kW
14.4
18.9
14.4
18.9
14.4
18.9
15.9
18.9
ELECTRICAL SERVICE CHARGE APPLIES
C A PA C I T Y
377 lb
501 lb
49"
(171 kg)
X
47"
X
(227 kg)
37"
EST .
(1245 x 1194 x 940mm)
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
HALF-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
18" x 13" x 1"
Ten (10)
Ten (10)
Ten (10)
120 lb (54 kg) MAXIMUM
75 QUARTS (95
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
PG .
67.0
77.0
38.6/ph
44.3/ph
21.1/ph
25.6/ph
20.0/ph
22.0/ph
AWG
50/60
WEIGHT
NET
17-15/16"
(456mm)
7-9/16"
(191mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
BACK : 4" (102mm)
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
*
Water Drain
DIMENSIONS: H x W x D
EXTERIOR :
41-1/2" x 43-7/8" x 34-1/16" (1053mm x 1114mm x 865mm)
EXTERIOR WITH RETRACTABLE DOOR :
41-1/2" x 47-7/8" x 34-1/16" (1053mm x 1216mm x 865mm)
INTERIOR :
27" x 23-1/2" x 21-1/16" (685mm x 597mm x 535mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
at
at
at
at
at
at
at
at
6-1/4" (158mm)
33-15/16" (861mm)
31-3/8" (796mm)
41-1/2" (1053mm)
Electrical Connection (Bottom)
34-1/16" (865mm)
7-9/16" (192mm)
Untreated Water
Intake (Bottom)
Low Pressure
Valve (Top)
Treated Water
Intake (Bottom)
43-7/8" (1114mm)
41-15/16" (1064mm)
60-9/16" (1538mm)
15-7/8"
(403mm)
14-3/16"
(360mm)
11-7/16"
(290mm)
4-3/4" (120mm)
Steam Vent (Top)
Water Drain
(Back Side)
2-3/16" (56mm)
—
INSTALLATION MANUAL
#MN-28677
LITERS )
Eight (8)
Eight (8)
Nine (9)
1 0 • 1 0 ES iN S P E C I F I C A T I O N S
®
COMBITHERM
21-15/16"
(557mm)
35-7/8" (910mm)
Water Drain
(Side Back)
35-11/16" (905mm)
33-7/8" (860mm)
2" (50mm)
25"
(635mm)
41-1/16" (1043mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
5" (126mm)
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
ELECTRICAL
10•10ESiN
440-480 380-415 208-240 208-240
VOLTAGE
at 208
PHASE
CYCLE/HZ
3
50/60
1*
at 240
at 208
at 240
at 380
3
at 415
at 440
AMPS
2 Wire plus ground
67.0
AWG 3
50/60
25.6/ph
20.0/ph
AWG 8
22.0/ph
10•10ESiN/sk
kW
AMPS
69.2
79.0
18.9
22.0/ph
14.4
13.9
40.0/ph
18.4
26.3/ph
18.4
15.4
18.4
14.4
45.5/ph
21.0/ph
23.0/ph
14.4
18.9
18.9
15.9
18.9
ELECTRICAL SERVICE CHARGE APPLIES
385 lb
500 lb
DIMENSIONS :
13.9
AWG 10
C A PA C I T Y
CRATE
21.1/ph
44.3/ph
3 Wire plus ground
13.9
18.4
38.6/ph
4 Wire plus ground
kW
77.0
3 Wire plus ground
AWG 6
50/60
3*
at 480
AWG
50/60
WEIGHT
SHIP
19-9/16"
(496mm)
7-9/16"
(191mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
RIGHT : 4" (102mm)
TOP : 20" (508mm) FOR AIR MOVEMENT
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
NET
WATER
DRAIN
DIMENSIONS: H x W x D
EXTERIOR :
41-3/8" x 35-7/8" x 35-11/16" (1050mm x 910mm x 905mm)
EXTERIOR WITH RETRACTABLE DOOR :
41-3/8" x 39-7/8" x 35-11/16" (1050mm x 1012mm x 905mm)
INTERIOR :
27" x 13-1/4" x 26-1/4" (685mm x 387mm x 665mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
*
6-3/8" (161mm)
Electrical Connection(Bottom)
33-7/8"
(859mm)
54-1/8" (1375mm)
Untreated Water Intake
(Bottom)
Low Pressure
Valve
Treated Water
Intake (Bottom)
41-3/8" (1050mm)
33" (837mm)
Steam
Vent
(Top)
7-9/16" (192mm)
(242mm)
12-5/16"
(312mm)
9-9/16"
19-1/2"
(495mm)
2-3/16" (55mm)
4-3/4" (120mm)
EST .
EST .
49"
X
(175 kg)
(227 kg)
44"
X
40"
EST .
EST .
EST .
(1245 x 1118 x 1016mm)
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
HALF-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
18" x 13" x 1"
Ten (10)
Ten (10)
Ten (10)
120 lb (54 kg) MAXIMUM
75 QUARTS (95
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
Eight (8)
Eight (8)
Nine (9)
LITERS )
#MN-28677
PG .
9
7 • 1 4 ES S P E C I F I C A T I O N S
®
COMBITHERM
Decalcification
Port
12-3/4"
(323mm)
15-1/2"
(393mm)
22-3/8" (568mm)
2-5/16" (58mm)
4-11/16" (120mm)
FRONT VIEW
Helvetica
TOP VIEW
ight Condensed
I N S TA L L AT I O N R E Q U I R E M E N T S
pt
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
SIDE VIEW
DIMENSIONS: H x W x D
EXTERIOR :
34-1/4" x 43-7/8" x 42-13/16" (869mm x 1114mm x 1087mm)
EXTERIOR WITH RETRACTABLE DOOR :
34-1/4" x 47-7/8" x 42-13/16" (869mm x 1216mm x 1087mm)
INTERIOR :
20-5/16" x 23-1/2" x 28-7/16" (515mm x 596mm x 722mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
RIGHT : 4" (102mm)
TOP : 20" (508mm) FOR AIR MOVEMENT
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
440-480 380-415 208-240 208-240
ELECTRICAL
VOLTAGE
at 208
at 240
PHASE
CYCLE/HZ
at 208
at 240
3
50/60
at 380
at 415
3
50/60
at 440
at 480
3*
50/60
1*
*
SHIP
CRATE
DIMENSIONS :
2 Wire plus ground
AWG 3
10
21.5/ph
25.6/ph
14.2
18.4
38.5/ph
44.0/ph
3 Wire plus ground
AWG 8
20.0/ph
22.0/ph
C A PA C I T Y
416 lb
540 lb
52"
(189 kg)
X
50"
X
(245 kg)
46"
EST .
(1321 x 1270 x 1168mm)
FULL-SIZE PANS:
GN 1/1:
GN 2/1:
FULL-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
168 lb (76 kg) MAXIMUM
105 QUARTS (133
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
PG .
13.9
18.4
3 Wire plus ground
AWG 6
4 Wire plus ground
AWG 10
kW
AMPS
67.0
77.0
13.8
18.3
15.4
18.4
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
NET
AWG
50/60
—
INSTALLATION MANUAL
#MN-28677
Fourteen (14)
Fourteen (14)
Seven (7)
Seven (7)
LITERS )
7 • 1 4 ES i S P E C I F I C A T I O N S
®
COMBITHERM
12-3/4"
(323mm)
15-1/2"
(393mm)
22-3/8" (568mm)
2-5/16" (58mm)
4-11/16" (120mm)
Low Pressure Valve
FRONT VIEW
elvetica
TOP VIEW
ght Condensed
I N S TA L L AT I O N R E Q U I R E M E N T S
pt
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
SIDE VIEW
DIMENSIONS: H x W x D
EXTERIOR :
34-1/4" x 43-7/8" x 42-13/16" (869mm x 1114mm x 1087mm)
EXTERIOR WITH RETRACTABLE DOOR :
34-1/4" x 47-7/8" x 42-13/16" (869mm x 1216mm x 1087mm)
INTERIOR :
20-5/16" x 23-1/2" x 28-7/16" (515mm x 596mm x 722mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
440-480 380-415 208-240 208-240
ELECTRICAL
7•14ESi
VOLTAGE
at 208
at 240
PHASE
CYCLE/HZ
at 208
at 240
3
50/60
at 380
at 415
3
50/60
at 440
at 480
3*
50/60
1*
*
50/60
SHIP
CRATE
DIMENSIONS :
2 Wire plus ground
AWG 3
AMPS
4 Wire plus ground
AWG 10
21.1/ph
25.6/ph
67.0
77.0
7•14ESi/sk
kW
13.9
18.4
AMPS
13.9
18.4
22.0/ph
26.3/ph
69.2
79.0
kW
14.4
18.9
3 Wire plus ground
AWG 6
38.6/ph
44.3/ph
13.9
18.4
40.0/ph
45.5/ph
14.4
18.9
3 Wire plus ground
AWG 8
20.0/ph
22.0/ph
15.4
18.4
21.0/ph
23.0/ph
15.9
18.9
14.4
18.9
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
NET
AWG
C A PA C I T Y
436 lb
560 lb
42"
(198 kg)
X
50"
X
(254 kg)
46"
EST .
(1067 x 1270 x 1168mm)
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
GN 2/1: 650 x 530 x 65mm
FULL-SIZE SHEET PANS:* 18" x 26" x 1"
ON WIRE SHELVES ONLY
* ADDITIONAL
Fourteen (14)
Fourteen (14)
Seven (7)
Seven (7)
168 lb (76 kg) MAXIMUM
105 QUARTS (133
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
Twelve (12)
Twelve (12)
Five (5)
Six (6)
LITERS )
#MN-28677
PG .
11
1 0 • 1 8 ES S P E C I F I C A T I O N S
®
COMBITHERM
43-7/8"
(1114mm)
41-15/16"
(1064mm)
42-13/16"
(1087mm)
Electrical Connection
(Bottom)
6-1/4" (158mm)
Treated Water
Intake (Bottom)
69-3/8" (1761mm)
Steam
Vents
(Top)
Untreated Water
Intake (Bottom)
40-7/16" (1026mm)
40-1/8"
(1019mm)
7-9/16" (192mm)
Water Drain
(Side Back)
Decalcification
Port
12-3/4"
(323mm)
15-1/2"
(393mm)
22-3/8"
(568mm)
4-11/16" (120mm)
2-5/16" (58mm)
32-7/8"
(834mm)
30"
(760mm)
25-5/8"
(650mm)
8-11/16"
(219mm)
4-15/16"
(125mm)
33-1/8"
(840mm)
Water Drain
(Bottom)
2" (50mm)
46-7/8" (1190mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
DIMENSIONS: H x W x D
EXTERIOR :
40-7/16" x 43-7/8" x 42-13/16" (1026mm x 1114mm x 1087mm)
EXTERIOR WITH RETRACTABLE DOOR :
40-7/16" x 47-7/8" x 42-13/16" (1026mm x 1216mm x 1087mm)
INTERIOR :
30-3/4" x 23-1/2" x 28-7/16" (781mm x 596mm x 722mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
TOP : 20" (508mm) FOR AIR MOVEMENT
RIGHT : 4" (102mm)
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
ELECTRICAL
VOLTAGE
208-240
at 208
3
380-415
at 240
AWG
3 Wire plus ground
61.3/ph
22.0
33.5/ph
22.0
AWG 2
3
50/60
4 Wire plus ground
at 440
3*
50/60
3 Wire plus ground
at 480
*
SHIP
CRATE
DIMENSIONS :
AWG 6
AWG 6
522 lb
646 lb
46"
(237 kg)
X
51"
X
(293 kg)
46"
EST .
(1168 x 1295 x 1168mm)
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
GN 2/1:
FULL-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
12
29.2
40.7/ph
29.2
36.0/ph
27.2
43.5/ph
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
240 lb (109 kg) MAXIMUM
150 QUARTS (190
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
PG .
70.0/ph
36.1
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
NET
kW
AMPS
50/60
at 380
at 415
440-480
CYCLE/HZ
PHASE
—
INSTALLATION MANUAL
#MN-28677
Twenty (20)
Twenty (20)
Ten (10)
Ten (10)
LITERS )
1 0 • 1 8 ES i S P E C I F I C A T I O N S
®
COMBITHERM
43-7/8"
(1114mm)
41-15/16"
(1064mm)
Electrical Connection
(Bottom)
33-1/8"
(840mm)
32-7/8"
(834mm)
6-1/4" (158mm)
40-1/8"
(1019mm)
Steam
Vents
(Top)
69-3/8" (1761mm)
Untreated Water
Intake (Bottom)
Low Pressure
Valve (Top)
Treated Water
Intake (Bottom)
42-13/16"
(1087mm)
7-9/16" (192mm)
Water Drain
(Side Back)
12-3/4"
(323mm)
22-3/8"
(568mm)
15-1/2"
(393mm)
4-11/16" (120mm)
2-5/16" (58mm)
40-7/16" (1026mm)
30"
(760mm)
Water Drain
(Bottom)
25-5/8"
(650mm)
8-11/16"
(219mm)
4-15/16"
(125mm)
2" (50mm)
46-7/8" (1190mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
DIMENSIONS: H x W x D
EXTERIOR :
40-7/16" x 43-7/8" x 42-13/16" (1026mm x 1114mm x 1087mm)
EXTERIOR WITH RETRACTABLE DOOR :
40-7/16" x 47-7/8" x 42-13/16" (1026mm x 1216mm x 1087mm)
INTERIOR :
30-3/4" x 23-1/2" x 28-7/16" (781mm x 596mm x 722mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
CLEARANCE REQUIREMENTS
LEFT : 6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
RIGHT : 4" (102mm)
TOP : 20" (508mm) FOR AIR MOVEMENT
BACK : 4" (102mm)
BOTTOM : 5-1/8" (130mm) FOR LEGS
COUNTER-TOP INSTALLATIONS MUST MAINTAIN 4" (102mm) MINIMUM
CLEARANCE FROM COUNTER SURFACE .
ELECTRICAL
10•18ESi
440-480
380-415
208-240
VOLTAGE
CYCLE/HZ
PHASE
at 208
3
at 240
AWG
50/60
3 Wire plus ground
AMPS
AWG 2
kW
61.1/ph
22.0
70.3/ph
29.2
10•18ESi/sk
AMPS
kW
62.5/ph
22.5
71.5/ph
29.7
at 380
3
50/60
4 Wire plus ground
33.5/ph
22.0
34.2/ph
22.5
at 440
3*
50/60
3 Wire plus ground
35.7/ph
27.2
36.4/ph
27.7
at 415
at 480
*
SHIP
CRATE
DIMENSIONS :
40.7/ph
AWG 8
43.5/ph
29.2
36.1
41.4/ph
44.0/ph
29.7
36.6
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
NET
AWG 8
C A PA C I T Y
520 lb
640 lb
46"
(236 kg)
X
51"
X
(290 kg)
46"
EST .
(1168 x 1295 x 1168mm)
FULL-SIZE PANS: 20" x 12" x 2-1/2"
GN 1/1: 530 x 325 x 65mm
GN 2/1: 650 x 530 x 65mm
FULL-SIZE SHEET PANS:* 18" x 26" x 1"
ON WIRE SHELVES ONLY
* ADDITIONAL
Twenty (20)
Twenty (20)
Ten (10)
Ten (10)
240 lb (109 kg) MAXIMUM
150 QUARTS (190
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
Eighteen (18)
Eighteen (18)
Eight (8)
Nine (9)
LITERS )
#MN-28677
PG .
13
1 2 • 2 0 ES S P E C I F I C A T I O N S
®
46-3/4"
(1186mm)
44-3/4"
(1136mm)
2" (50mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
BACK :
6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
4" (102mm)
TOP :
4" (102mm)
BOTTOM :
33-1/2"
(851mm)
2-1/16" (52mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
RIGHT :
Water Drain
(Bottom)
DIMENSIONS: H x W x D
EXTERIOR :
54-3/8" x 46-3/4" x 48" (1381mm x 1186mm x 1218mm)
EXTERIOR WITH RETRACTABLE DOOR :
54-3/8" x 50-3/4" x 48" (1381mm x 1288mm x 1218mm)
INTERIOR :
38-11/16" x 26-1/4" x 32-11/16" (983mm x 667mm x 830mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
LEFT :
45-5/16"
(1151mm)
1-13/16"
(46mm)
40-15/16"
(1039mm)
51-15/16"
(1319mm)
7-11/16" (195mm)
Treated Water
Intake (Bottom)
Electrical
Connection (Bottom)
54-3/8" (1381mm)
Steam
Vents
(Top)
Untreated Water
Intake
(Bottom)
46-1/2"
(1155mm)
4-1/4"
(106mm)
48"
(1218mm)
8-15/16"
(226mm)
11-7/8"
(302mm)
Water Drain
(Side Back)
76-15/16" (1954mm)
13-1/16" (331mm)
6-11/16"
(169mm)
22-11/16"
(576mm)
15-13/16" (401mm)
COMBITHERM
20" (508mm)
FOR AIR MOVEMENT
5-1/8" (130mm)
FOR LEGS
ELECTRICAL
VOLTAGE
208-240
at 208
3
380-415
at 240
AWG
50/60
3 Wire plus ground
AWG 2
27.2
36.1
50/60
4 Wire plus ground
41.4/ph
27.2
at 440
3*
50/60
3 Wire plus ground
36.0/ph
27.2
at 480
NET
SHIP
CRATE
DIMENSIONS :
AWG 6
AWG 6
50.0/ph
35.7
43.5/ph
36.1
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
747 lb
1070 lb
61"
(339 kg)
X
(485 kg)
58"
X
53"
(1549 x 1473 x 1346mm)
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
GN 2/1:
FULL-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
288 lb (131 kg) MAXIMUM
180 QUARTS (228
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
14
75.6/ph
87.0/ph
3
*
PG .
kW
AMPS
at 380
at 415
440-480
CYCLE/HZ
PHASE
—
INSTALLATION MANUAL
#MN-28677
Twenty-four (24)
Twenty-four (24)
Twelve (12)
Twelve (12)
LITERS )
2 0 • 2 0 ES S P E C I F I C A T I O N S
®
COMBITHERM
51-15/16" (1319mm)
40-15/16"
(1039mm)
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET:
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
* Can manifold off of one 3/4" line.
BACK :
TOP :
4" (102mm)
BOTTOM :
7-11/16" (195mm)
USING A WATER SUPPLY NOT MEETING ALTO-SHAAM'S
MINIMUM WATER QUALITY STANDARDS WILL VOID THIS
WARRANTY. It is the responsibility of the purchaser to ensure that
incoming water supply is compliant with the specifications listed
through adequate treatment measures. Installation of the
CombiGuard™ Water Filtration System is recommended, but this
system may not address all water quality issues present.
Contaminant
Inlet Water Requirements (untreated water)
Free Chlorine
Less than 0.1 ppm (mg/L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg/L)
Silica
Less than 12 ppm (mg/L)
Total Dissolved
Solids (tds)
Less than 60 ppm
6" (152mm) PLUS SERVICE ACCESS : 18" (457mm) RECOMMENDED
20" (508mm) F R O M H E AT P R O D U C I N G E Q U I P M E N T
4" (102mm)
33-1/2"
(851mm)
2-1/16" (52mm)
WAT E R Q U A L I T Y M I N I M U M S TA N D A R D S
CLEARANCE REQUIREMENTS
RIGHT :
67-3/8" (1710mm)
1-13/16"
(46mm)
Water Drain
(Bottom)
DIMENSIONS: H x W x D
EXTERIOR :
76-1/4" x 46-3/4" x 48" (1936mm x 1186mm x 1218mm)
EXTERIOR WITH RETRACTABLE DOOR :
76-1/4" x 50-3/4" x 48" (1936mm x 1288mm x 1218mm)
INTERIOR :
60-1/4" x 26-1/4" x 32-11/16" (1530mm x 667mm x 830mm)
I N S TA L L AT I O N R E Q U I R E M E N T S
Oven must be installed level.
Hood installation is required.
Water supply shut-off valve and back-flow
preventer.
LEFT :
76-1/4" (1936mm)
2" (50mm)
8-15/16" (226mm)
Steam
Vents
(Top)
Electrical
Connection (Bottom)
Untreated Water
Intake (Bottom)
Treated Water
Intake (Bottom)
48"
(1218mm)
45-5/16"
(1151mm)
76-15/16" (1954mm)
24-7/8"
(629mm)
12-15/16"
(326mm)
4-3/4"
(120mm)
27-5/8"
(699mm)
46-3/4"
(1186mm)
44-3/4"
(1136mm)
11-7/8"
(302mm)
Water Drain
(Side Back)
5" (127mm)
20" (508mm)
FOR AIR MOVEMENT
5-1/8" (130mm)
FOR LEGS
ELECTRICAL
440-480
380-415
208-240
VOLTAGE
CYCLE/HZ
PHASE
at 208
3
at 240
50/60
3 Wire plus ground
AWG 4
at 380
3
50/60
4 Wire plus ground
at 440
3*
50/60
3 Wire plus ground
at 415
at 480
*
958 lb
SHIP
CRATE
DIMENSIONS :
kW
AMPS
151.2/ph
54.4
83.0/ph
54.4
173.4/ph
AWG 2
101.0/ph
AWG 2
87.0/ph
72.2
72.2
71.5/ph
54.4
72.2
ELECTRICAL SERVICE CHARGE APPLIES
WEIGHT
NET
AWG
EST .
1340 lb
83"
(435 kg)
X
EST .
(608 kg)
54"
X
53"
(2108 x 1372 x 1346mm)
C A PA C I T Y
FULL-SIZE PANS:
GN 1/1:
GN 2/1:
FULL-SIZE SHEET PANS:*
ON WIRE SHELVES ONLY
* ADDITIONAL
20" x 12" x 2-1/2"
530 x 325 x 65mm
650 x 530 x 65mm
18" x 26" x 1"
480 lb (218 kg) MAXIMUM
300 QUARTS (380
VOLUME MAXIMUM :
WIRE SHELVES REQUIRED FOR MAXIMUM CAPACITY
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
Forty (40)
Forty (40)
Twenty (20)
Twenty (20)
LITERS )
#MN-28677
PG .
15
L O C AT I O N S I T E & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
DANGER
DANGER
IMPROPER INSTALLATION,
ALTERATION, ADJUSTMENT,
SERVICE, OR MAINTENANCE COULD
RESULT IN SEVERE INJURY, DEATH
OR CAUSE PROPERTY DAMAGE.
AVERTISSEMENT : UNE INSTALLATION,
UN AJUSTEMENT, UNE ALTÉRATION,
UN SERVICE OU UN ENTRETIEN NON
CONFORME AUX NORMES PEUT CAUSER
DES DOMMAGES À LA PROPRIÉTÉ, DES
BLESSURES OU LA MORT.
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
LIRE ATTENTIVEMENT LES DIRECTIVES
D’OPÉRATION ET D’ENTRETIEN AVANT
DE FAIRE L’INSTALLATION, OU
L’ENTRETIEN DE CET ÉQUIPEMENT.
®
THE OVEN MUST REMAIN ON
THE PALLET WHILE BEING
MOVED TO THE INSTALLATION
SITE BY FORK LIFT OR
PALLET LIFT TRUCK.
NOTE:
Note dimensions required for doorways
and aisles for access of the oven and
pallet to the installation site. Transport
the oven in an upright and level position
only. Do not tilt the oven.
I N S TA L L AT I O N C O D E S & S TA N D A R D S
The following codes and standards are required for installation of this oven:
AIR SUPPLY, ELECTRICAL CONNECTIONS, WATER CONNECTIONS, AND
WASTE WATER DISCHARGE.
Where automatically operated appliances are vented through a ventilating hood or exhaust
system equipped with a damper or with a power means of exhaust, provisions shall be made
to allow the equipment to operate only when the damper is open to a position to properly
vent the appliance and when the power means of exhaust is in operation.
IN ACCORDANCE WITH NFPA 54 COMMONWEALTH OF MASSACHUSETTS ONLY.
ELECTRIC COMBITHERM
PG .
16
—
INSTALLATION MANUAL
#MN-28677
N
O
T
E
®
L O C AT I O N S I T E & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
VENTILATION REQUIREMENTS
A steam ventilation hood is mandatory for the
operation of the oven. The ventilation hood must
be installed in accordance with local building
codes for the steam exhaust and must protrude
12-inches to 20-inches (300 to 500mm) over the
front side of the oven. A grease filter must be
located in the protruding area of the hood. Grease
filters should be thoroughly cleaned on a regular
basis following manufacturer's instruction.
Ventilation hoods must ensure an adequate
amount of incoming air during operation and
must be operated whenever the combination
oven/steamer is used in order to avoid the
accumulation of condensation in the hood area.
CAUTION
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
POSITIONING ON SITE
Lift the oven from the pallet with a fork lift or
pallet lift truck positioned at the front of the oven.
For damage protection, the use of two wooden
boards, placed between the bottom of the oven
and the lifting forks, is strongly recommended. To
avoid damage, position the lift forks to the left of
the condenser and right of the right leg as
indicated in the diagram at right.
Stand the oven in a level position. Use the
adjustable feet to overcome an uneven floor and
ensure that the unit is level.
Adjust the height of floor models for smooth
access of the trolley or cart. When positioning the
oven, observe the minimum space allocation
requirements shown.
To insure proper operation, the installation of this
oven must be completed by qualified technicians
in accordance with the instructions provided in
this manual. Failure to follow the instructions
provided may result in damage to the oven,
building, or cause personal injury to personnel.
—
attention label on oven for area to avoid
with lifting fork.
MINIMUM CLEARANCE REQUIREMENTS
LEFT SIDE
6" (152mm)
MINIMUM
18" (457mm)
It is strongly recommended that table top models
be mounted on a factory supplied stand or a stand
that is stable, open, level, and non-combustible.
Recommended height is 23-inches (584mm).
ELECTRIC COMBITHERM
NOTE: To avoid equipment damage, observe
20" (508mm)
RIGHT SIDE
BACK
TOP
SERVICE ACCESS RECOMMENDED
FROM HEAT PRODUCING EQUIPMENT
4" (102mm)
4" (102mm)
FOR PLUMBING
20" (508mm)
FOR AIR MOVEMENT
NOTE: Additional clearance is needed for service
access. A minimum distance of 18-inches is
strongly recommended. If adequate service
clearance is not provided, it will be necessary to
disconnect the gas, water, and drain to move the
oven with a fork lift for service access. Charges in
connection with inadequate service access is not
covered under warranty.
INSTALLATION MANUAL
#MN-28677
PG .
17
L O C AT I O N S I T E & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
POSITIONING REQUIREMENTS
❑ In order to ensure proper ventilation, a
minimum distance of at least 6-inches (152mm)
must be kept from the control panels side (left)
of the oven and any adjoining surfaces.
NOTE: Additional clearance is needed for
service access. A minimum distance of 18-inches
is strongly recommended. If adequate service
clearance is not provided, it will be necessary to
disconnect the gas, water, and drain to move the
oven with a fork lift for service access. Charges
in connection with inadequate service access is
not covered under warranty.
❑ Allow a minimum of 4-inches (102mm) from the
right side of the oven to allow the door to open
to at least a 90° angle. Fully opened, the door
will extend up to a 225° angle If the oven is
furnished with the retractable door option,
allow a minimum clearance of
6-1/2 inches (165mm).
❑ Allow a minimum clearance of 4-inches
(102mm) from the back of the oven for
plumbing connections.
❑ Allow a 20-inch (500mm) clearance at the top of
the oven for free air movement and for the
steam vent(s) located at the top.
❑ Do not install the oven adjacent to heat
producing equipment such as fryers, broilers,
etc. Heat from such appliances may cause
damage to the controls of the Combitherm.
Minimum clearance recommended:
20-inches (500mm)
Place the Combitherm oven on a stable,
non-combustible level horizontal surface. For
countertop models, the oven
stand must be
level. In
addition, the
overall height of the oven should be positioned so
the operating controls and shelves may be
conveniently reached from the front. Level the
oven front-to-back and side-to-side by means of
the adjustable legs.
ELECTRIC COMBITHERM
PG .
18
—
INSTALLATION MANUAL
#MN-28677
E L E C T R I C A L & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
DANGER
DANGER
To avoid electrical shock, this
appliance MUST be adequately
grounded in accordance with local
electrical codes or, in the absence of
local codes, with the current edition
of the National Electrical Code
ANSI/NFPA No. 70. In Canada, all
electrical connections are to be
made in according with CSA C22.1,
Canadian Electrical Code Part 1 or
local codes.
ENSURE POWER SOURCE
MATCHES VOLTAGE STAMPED
ON APPLIANCE NAMEPLATE.
An electrical wiring diagram is located behind the
control panel on the left side of the oven. The oven
must be installed by a qualified electrician. This
appliance must be branch circuit protected with
proper ampacities, in accordance with the wiring
diagram located in the electrical compartment of the
oven. The oven must be properly grounded in
accordance with the National Electrical Code and
applicable local codes.
DANGER
ELECTRICAL CONNECTIONS MUST
BE MADE BY A QUALIFIED SERVICE
TECHNICIAN IN ACCORDANCE WITH
APPLICABLE ELECTRICAL CODES.
Wire size for the main incoming power to the unit
must match the minimum size listed in the
specifications applicable to the specific oven model.
For supply connections, locate the wire size posted
on the label located on the electrical control box
cover, behind the service panel.
When connecting to a Delta-B (wild leg) on a 3-phase
system, the wild leg must be connected to line 3.
Before operating the oven, check all cable
connections in the electrical connection area for
tightness since connections can loosen during
transport.
NOTE: After both water and electrical connections
have been completed, operate the oven in
any cooking mode for a period of 15
minutes and recheck the main power
connections at the terminal block to make
certain they remain tight.
380-415V:
To prevent an electrical shock hazard between the
appliance and other appliances or metal parts in
close vicinity, an equalization-bonding stud is
provided.
An equalization bonding lead must be connected
to this stud and the other appliances / metal parts
to provide sufficient protection against potential
difference. The terminal is marked with
the following symbol.
MOTOR WITH
FOLLOWING ELECTRICAL CONNECTION,
THE FAN M U S T ROTATE IN THE SAME
DIRECTION AS THE ARROW LOCATED
ON THE OVEN FAN MOTOR.
ROTATION
DIRECTION
T H I S A P P L I A N C E W I L L N OT F U N C T I O N
P RO P E R LY A N D DA M AG E C A N O C C U R I F
T H E M OTO R ROTAT I O N I S N OT C O R R E C T.
ELECTRICAL
CONNECTION
TO CHANGE MOTOR DIRECTION,
EXCHANGE TWO OF THE INCOMING PHASES.
TERMINAL BLOCK
GROUND
ELECTRICAL PANEL
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
19
I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
D R I P T R AY I N S TA L L AT I O N
The appliance is shipped without the drip tray
installed. This must be installed before equipment
operation begins.
� Position drip tray mounting bracket beneath oven.
Secure with lock washer and phillips screws supplied.
� Slide drip tray assembly into mounting bracket.
Secure with lock washer and nut.
� Attach drip tray hose to drip tray assembly. Secure the
drain fitting connection with the 19mm clamp. Pull hose
tight, cut hose to length, and secure the drip tray hose
connection with the 20mm clamp.
WA R N I N G
FAILURE TO PROPERLY INSTALL THE
DRIP TRAY CAN OR WILL CAUSE
MAJOR EQUIPMENT DAMAGE AND
WILL RESULT IN A LEAKAGE
HAZARD THAT CAN CAUSE
PERSONAL INJURY.
�
ITEM
NO .
PART
NO .
1
1006674
2
—
3
�
�
PART DESCRIPTION
QTY
DRIP TRAY MOUNTING BRACKET
1
DRIP TRAY
1
HO-27220 DRIP TRAY HOSE
1
MOBILE EQUIPMENT RESTRAINT
Any appliance that is not furnished with a power
supply cord but includes a set of casters must be
installed with a tether. Adequate means must be
provided to limit the movement of this appliance
without depending on or transmitting stress to the
electrical conduit. The following requirements apply:
WA R N I N G
RISK OF ELECTRIC SHOCK.
Appliance must be secured
to building structure.
1. Casters must be a maximum height of 6" (152mm).
2. Two of the casters must be the locking type.
3. Such mobile appliances or appliances on mobile
stands must be installed with the use of a flexible
connector secured to the building structure.
A mounting connector for a restraining device is
located on the lower back flange of the appliance
chassis or on an oven stand, approximately
18" (457mm) from the floor. A flexible connector is
not supplied by nor is it available from the factory.
ELECTRIC COMBITHERM
PG .
20
—
INSTALLATION MANUAL
#MN-28677
®
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
COMBITHERM
WAT E R Q U A L I T Y R E Q U I R E M E N T S
USE A DRINKING QUALITY, COLD WATER SUPPLY ONLY
Water quality is of critical importance when
installing steam producing equipment of any kind,
particularly high temperature steam producing
equipment. Water that is perfectly safe to drink is
composed of chemical characteristics that directly
affect the metal surfaces of steam producing
equipment. These chemical characteristics differ
greatly from region to region throughout the U.S.
and the world. Varying combinations of pH;
alkalinity; hardness; chlorides; total dissolved
solids; and other chemical characteristics, when
subjected to high temperatures, will cause water to
have a tendency to either scale or corrode.
Alto-Shaam has consulted with people who
understand the properties of water in order to
provide water quality standards that meet the
broadest possible range of acceptable water quality
requirements to help protect your investment.
We strongly urge water testing to ascertain the
water quality on site prior to the installation of any
steam producing equipment. Since water quality is
an important issue, Alto-Shaam is committed to
provide as much information as possible to help
protect the investment made in this equipment.
A CombiGuard ™ Water Filtration System can be
purchased as an option for installation on the
Combitherm oven. This filter, when properly
installed, maintained, and combined with the
required levels of steam generating equipment
maintenance, will help lessen the affect water has on
metal surfaces. It will not, however, provide
complete protection against all water damage from
region to region.
Due to the complexity of water chemistry, it is
important to understand that water quality plays a
significant role in the longevity of steam producing
equipment. Water quality and required maintenance
of steam generating equipment is the direct
responsibility of the owner/operator. Damage
incurred as a direct result of poor water quality
and/or surfaces affected by water quality is also the
responsibility of the owner/operator. Damage due
to water quality that does not meet the minimum
standards shown below is not covered under the
Alto-Shaam Combitherm warranty.
Alto-Shaam will continue our efforts to provide
viable solutions to ease the impact of water quality
as it relates to steam generating equipment.
ALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS
CONTAMINANT
INLET WATER REQUIREMENTS (UNTREATED WATER)
Free Chlorine
Less than 0.1 ppm (mg\L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg\L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg\L)
Silica
Less than 12 ppm (mg\L)
Total Dissolved Solids (tds)
Less than 60 ppm
TO PREVENT WATER PIPES OR HOSES
F R O M B U R S T I N G , I N C O M I N G WAT E R
SUPPLY SHOULD BE TURNED OFF WHEN
THE APPLIANCE IS NOT IN USE.
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
21
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
Flush the water line at the installation site before
connecting the oven to the water supply. A hose connector
is supplied for flexible hose connection to the COLD water
source.
WAT E R R E Q U I R E M E N T S
TWO (2) COLD WATER INLETS - DRINKING QUALITY
3/4" NPT*
ONE (1) UNTREATED WATER INLET:
3/4" NPT*
LINE PRESSURE:
30 to 90 psi
2.8 to 6.2 bar
* Can manifold off of one 3/4" line
ONE (1) TREATED WATER INLET:
PIPE SEALING TAPE ( TEFLON ®) MUST BE USED AT
ALL CONNECTION POINTS. The use of a pipe sealing
REFER TO PUBLISHED SPECIFIC WATER REQUIREMENTS
compound is not recommended.
WATER DRAIN: 1-1/2" CONNECTION WITH AIR GAP
ONE SUGGESTED METHOD OF INSTALLATION
Incoming cold water
connection
Water Filter
T connection
Cold water line to
filter or treatment
system
Treated cold
water to treated
connection on oven
Cold water line to
untreated oven
connection
NOTE:
BOTH TREATED AND UNTREATED WATER
CONNECTIONS MUST BE CONNECTED FOR PROPER
OPERATION OF THE OVEN. BOTH CONNECTIONS
CAN BE TREATED WATER, BUT SHOULD NEVER BE
CONNECTED TO ONLY UNTREATED WATER.
UNIONS OR FLEXIBLE LINES SHOULD BE USED TO
ALLOW FOR OVEN MOVEMENT WHEN BEING
SERVICED OR CLEANING IS NEEDED.
REFER TO DIMENSION DRAWINGS BEGINNING ON
PAGE 4 FOR PROPER INTAKE LOCATIONS.
ELECTRIC COMBITHERM
PG .
22
—
INSTALLATION MANUAL
#MN-28677
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
S H U T - O F F V A LV E S H O W N
IN THE OFF POSITION
NOTE:
THE SHUT-OFF VALVE
MUST BE IN THE OPEN POSITION
WHEN THE OVEN IS BEING USED.
ITEM FI-23014
Alto-Shaam now offers an improved water filtration system for
Combitherm®. The CombiGuard™ triple-guard water filtration system filters
dirt, sediment, and other debris as small as 1/2 micron. This system also
significantly reduces chlorine content to protect against corrosive chlorine
compounds. CombiGuard improves equipment efficiency, reduces service
requirements and extends the life of the Combitherm. Filtration system
includes one filter cartridge. Additional cartridges (FI-26356) can be
purchased separately.
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
23
WAT E R S U P P LY & I N S TA L L AT I O N R E Q U I R E M E N T S
®
COMBITHERM
WAT E R D R A I N A G E
The oven must discharge through an indirect waste pipe by means of an air gap. The drain fitting is
supplied with a 1-1/2-inch (41mm) NPT thread on one end and a 1-1/2-inch (41mm) barbed connection
on the opposite end.
AVERAGE
DRAIN
WATER
A union is required. Install a 1-1/2-inch
TEMPERATURE
(41mm) diameter connection, drain line and
clamp into place. The drain line must always be
a positive gradient away from the Combitherm
oven and not more than 12-inches (305mm)
before an air gap.
149°F (65°C)
NOTE: In the U.S.A., this equipment is to be
installed to comply with the Basic
Plumbing Code of the Building
Officials and Code Administrators
International, Inc. [BOCA], and the
Food Service Sanitation Manual of the
Food & Drug Administration [FDA].
2" (51mm)
Air Gap
(41mm)diameter NPT
1-1/2"(32mm)
1-1/4"
diameter connection
required
If several units are to be connected to one drain
pipe, the dimensions of the pipe must be
sufficient to allow an unobstructed water drain
system.
WASTE PIPE
1-1/2" to 2" minimum diameter
(c. 38mm to 51mm)
1-1/2” (41mm)
diameter NPT
condensate pan
clean out
ELECTRIC COMBITHERM
PG .
24
—
INSTALLATION MANUAL
#MN-28677
I N S TA L L AT I O N C H E C K L I S T
®
COMBITHERM
Use this list as a final check of oven installation conformance. Damage directly attributed to improper set up, installation,
or cleaning can invalidate warranty claims.
CLEARANCES:
Left:
6” (152mm) — Service access of 18” (457mm) recommended.
20” (508mm) from heat producing equipment.
Right: 4” (102mm)
Back: 4” (102mm) for plumbing
Top:
20” (508mm) for air movement
ARE ALL CLEARANCE
REQUIREMENTS MET?
■ YES
■ NO
IF NO, EXPLAIN: ________________________
________________________________________
WAT E R S U P P LY A N D D R A I N S :
Verify hook-up to TWO (2) separate cold water supply lines with a 3/4" (19mm) water ARE BOTH WATER SUPPLY LNES
■ NO
PROPERLY CONNECTED? ■ YES
connection supply line. Verify inlet water pressure is at a minimum of 30 PSI (2.8
bar). Maximum water pressure is not to exceed 90 PSI (6 bar). Verify drain diameter IF NO, EXPLAIN: __________________________
of 1-1/2" (41mm) with a positive descending slope, and with a 2" (51mm) air gap
IS A FILTER SYSTEM INSTALLED
which is free of obstructions before connection to the site drain. Verify 1/8" (3,2mm)
■ YES
■ NO
ON THIS UNIT?
pitch to 10' (305cm) of drain line.
IMPORTANT: Alto-Shaam has listed Water Quality Requirements in the
STORE HAS SEEN THIS
installation manual for this equipment. It is the responsibility of the end user
■ YES
■ NO
RECOMMENDATION:
to have the water connected to this appliance tested to ensure these standards
are met before putting the oven into use. Failure to meet these standards will void SIGNATURE OF STORE REPRESENTATIVE:
the warranty if damage to the oven is found to be related to water quality.
___________________________________________
ELECTRICAL CONNECTIONS:
Verify electrical power
VOLTAGE: ______________ LINE VOLTAGE AT TERMINAL BLOCK (TO GROUND):
requirements for oven.
Verify voltage at terminal
block. Check all terminals
PHASE: ______________
LINE VOLTAGE (PHASE TO PHASE): LINE 1 to 2: __________
LINE 2 to 3: __________
BREAKER SIZE: ______________
LINE 3 to 1: __________
for tightness.
ELECTRICAL SUPPLY LINE SIZE: ______________
C O N T RO L B OA R D C O N N E C T I O N S & O P E R AT I O N :
With the Power Key OFF , press and hold the Chef Function
Key to access software version, and record.
SOFTWARE VERSION:
BM_____________ SM_____________ KM_____________
PHYSICAL CONDITION:
➥ LINE 1: _________ LINE 2:_________ LINE 3: _________
*REFERENCE
CORRECT MOTOR ROTATION: ■ YES
■ NO
ALL ELECTRICAL TERMINALS TIGHT: ■ YES
■ NO
ALL BOARD CONNECTIONS TIGHT: ■ YES
■ NO
ALL FUNCTIONS LIGHT UP: ■ YES
■ NO
ALL FUNCTIONS ON CONTROL OPERATE: ■ YES
■ NO
UNIT OPERATES IN ALL MODES: ■ YES ■ NO
IF NO, EXPLAIN: ________________________________________
✔
I N S TA L L AT I O N I N S T R U C T I O N S F O R C O M P L E T E I N F O R M AT I O N
■
Bottom of oven has been checked for damage due to improper positioning on site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
Verify all gaskets, hoses, and carts* are in place and function properly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
■
If oven includes a cart, verify proper installation of the rack guide* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
■
■
Verify the installation of drip pans* , racks, shelves, drain screen, spray hose* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
■
Verify the oven is level and installed on a solid, water resistant floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .■
SERVICE AGENCY:
START-UP DATE:
INSTALLATION NAME:
MODEL NO.:
SERIAL NO.:
TECH SIGNATURE:
CUSTOMER SIGNATURE:
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
25
ERROR CODES
®
COMBITHERM
CONTROL RESET
There is a remote possibility in the day-to-day operation of the Combither m that the control could
lock or freeze. If this occurs, the control is easy to reset.
PRESS AND HOLD THE POWER KEY FOR A PERIOD OF 5 SECONDS.
Release the POWER KEY.
The control will will reset itself within approximately 15 seconds.
WHEN RESET, THE DISPLAY WILL INDICATE THE TIME AND DATE AND THE CONTROLS WILL BE FULLY FUNCTIONAL.
SERVICE MODE AND ERROR CODES
When the oven malfunctions, an error code will appear in the display.
PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.
The keys that begin to flash represent operational modes that are still usable. Refer to Emergency
Operation.
When the oven fault is corrected, the Combitherm will return to normal Operation.
ERROR CODES AND REASONS
Error
Code
E01
Display Shows
Low Water
When does the error occur?
Possible reason
ES units only:
• Water supply is shut off.
• Activated if running in any mode and the
water level drops below the low level sensor. • Low water pressure.
• Steam generator drain cap is off or loose.
• Activated if not in running mode and the
water level drops below the low level sensor • Drain pump is not sealing.
for 3 minutes.
• Faulty or scaled water level probe.
• Faulty or plugged solenoid valve assembly.
• Wiring or connection issue.
E02
Control Temp High
Activated if the temperature of the electrical
control is higher than 176°F for 20 seconds.
• Cooling fan not operating.
• Unit is next to a heat producing source (there
is less than 20" clearance for the control
side).
• Exhaust hood is not operating (if applicable).
E03
Fan Malfunction
Activated if the motor protection switch is
tripped.
• Motor rotation is backwards.
• Incorrect power to the unit.
• Connection problem at X-7 plug on relay
board pins 3-4.
E04
Aux Fan Fault
Auxiliary fan malfunction.
E11
Excess Oven Temp
Activated if the oven cavity temperature is
higher than 518°F for 25 seconds.
• Control setup programming error.
• Contact factory.
• Connection issue with oven temperature
sensor.
• Convection element contactor is stuck.
• Faulty oven temperature sensor.
ELECTRIC COMBITHERM
PG .
26
—
INSTALLATION MANUAL
#MN-28677
ERROR CODES
®
COMBITHERM
ERROR CODES AND REASONS (continued)
Error
Code
E13
Display Shows
Excess Steam Gen Temp
When does the error occur?
ES units only:
Activated if the temperature of the steam
generator probe (B-4) is higher than 248°F
for 26 seconds.
Possible reason
• Problem with water level probe.
• Scale build-up inside steam generator.
• Steam element contactor is stuck.
• Connection issue with B-4 probe.
• Faulty B-4 probe.
ESi units only:
• Jumper on X-3 is improperly positioned.
Activated if the position of personality jumper
Should be between 2-8 or, if it is a smoker,
on X-3 is incorrect.
between 2-9.
Activated if the position of B-4 jumper is
incorrect.
E15
Excess Condensate Temp
• Jumper on X-6a is improperly positioned.
Should be between 13-14.
Activated if the temperature of the condensate • Water supply is shut off.
probe (B-3) is higher than 212°F for 26
• Faulty or plugged solenoid valve (Y-2).
seconds.
• Connection issue at B-3 probe.
• Faulty B-3 probe.
E21
E22
Oven Probe Fault
Core Temp Probe Fault
Activated if oven temperature probe (N-6) is
interrupted.
• Connection issue at N-6 probe.
Activated if cooking in Core Temp mode and
the CTC sensor measures an excessive
temperature.
• CTC sensor is damaged.
• Faulty N-6 probe.
• 4-point CTC sensor is activated, but 1-point
CTC sensor is installed.
• Cable connection of CTC sensor is damaged.
• Hardware problem on control unit (SM).
E23
E24
E25
E26
E27
Steam Gen Probe Fault
ES units only:
• Connection issue at B-4 probe.
Activated if the steam generator probe (B-4) is
• Faulty B-4 probe.
interrupted.
• Jumper on X-3 is imperly positioned.
ESi units only:
Should be between 2-8 or, if it is a smoker,
• Activated if the position of personality
between 2-9.
jumper on X-3 is incorrect.
• Activated if the position of B-4 jumper is
incorrect.
• Jumper on X-6a is improperly positioned.
Should be between 13-14.
Activated if the bypass probe (B-5) is
interrupted.
• Connection issue at B-5 probe.
Activated if the condensate probe (B-3) is
interrupted.
• Connection issue at B-3 probe.
Steam Gen Safety Probe
Fault
Activated if the steam generator safety probe
(N-8) is interrupted.
• Connection issue at N-8 probe.
Excess Steam Gen Safety
Temp
Activated if the steam generator safety probe
(N-8) measures a temperature in excess of
266°F.
•
•
•
•
•
ESi units only:
• Activated if the position of N-8 jumper is
incorrect.
• Jumper on X-6b is improperly positioned.
Should be between 1-2.
Bypass Probe Fault
Condensate Probe Fault
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
• Faulty B-5 probe.
• Faulty B-3 probe.
• Faulty N-8 probe.
Problem with water level probe.
Scale build-up inside steam generator.
Steam element contactor is stuck.
Connection issue with N-8 probe.
Faulty N-8 probe.
#MN-28677
PG .
27
ERROR CODES
®
COMBITHERM
ERROR CODES AND REASONS (continued)
Error
Code
E29
Display Shows
Probe Short to Frame
E34
DE (Drain) Pump Failure
When does the error occur?
Activated if one or more of the temperature
sensors were connected to GND for 5
seconds.
Possible reason
• Connection issue at any of the temperature
sensors.
• Temperature sensor shorted to
ground/faulty.
Activated if water level did not drop below the • Problem with water level probe.
low level sensor in the generator during a
• Scale build-up inside steam generator.
steam generator flush.
• Scale plugging drain pump.
• Faulty drain pump.
E35
Venting Error
Activated when vent switch reads open (vent
closed) when it should be closed (vent open),
or when it reads closed (vent open) when it
should be open (vent closed).
• Alignment issue between motor cam and
micro switch.
• Connection issue at micro switch.
• Connection issue at control.
• Faulty vent switch.
• Faulty vent motor.
E36
Steam Temp High
Activated when oven temperature probe (N-6) • Water supply is shut off while unit is running
measures a temperature in excess of 395°F
in Steam or Combi mode.
when running in Steam or Combi mode.
• Plugged or faulty Y-1 solenoid.
• Obstruction between Y-01 solenoid and
water inlet.
E80
ID Error
Control is unable to detect whether unit is gas • Connection issue at X-3 personality jumper.
or electric.
• Faulty control.
E81
Program Memory Error
Temperature value or time value of a program • Program was generated in °C and control has
step is not allowed.
been switched to °F.
• Program was generated in °F and control has
been switched to °C.
E82
WP Error
Temperature value or time value of current
cooking algorithm is out of allowed array.
• Delete program and reinstall.
E83
Algo Error
Cooking algorithm sent by operating module
(BM) is unknown to control unit (SM).
• Software versions of control unit and
operating module are incompatible.
• Software error in operating module.
E96
Connection Error
No or bad communication between control
unit (SM) and operating module (BM).
• Connection issue at ribbon cable on display
or relay board.
• Faulty ribbon cable.
• Software versions of control unit and
operating module are incompatible.
ELECTRIC COMBITHERM
PG .
28
—
INSTALLATION MANUAL
#MN-28677
ERROR CODES
®
COMBITHERM
E M E R G E N C Y O P E R AT I O N
In the event of an error code, the Combitherm may be operated on a limited basis. Error conditions under
which continued operation can be conducted are indicated by “Yes” in the chart shown below.
When the oven malfunctions, an error code will appear in the display.
PRESS THE START KEY TO ACKNOWLEDGE THE ERROR.
The keys that begin to flash represent operational modes that are still usable.
SELECT AND PRESS ONE OF THE COOKING MODES INDICATED.
The oven control will only respond to the mode keys that are flashing.
SET THE OVEN CONTROLS AS IF OPERATING UNDER NORMAL CIRCUMSTANCES.
Depending on the error code involved, oven function, such as temperature range, may be limited.
PRESS THE START KEY TO BEGIN THE COOKING PROCESS.
PRESS THE START KEY WHEN THE TIMER EXPIRES.
When the oven fault is corrected, the Combitherm will return to normal Operation.
CONTINUED OPERATION UNDER ERROR CONDITIONS
Error
Code
Display Shows
ES
ESi
Steam
Mode
Combination
Mode
Convection
Mode
Retherm
Mode
E01
Low Water
Yes
No
No
No
To 365°F
No
E02
Control Temp High
Yes
Yes
Yes
To 284°F
To 284°F
To 284°F
E03
Fan Malfunction
No
No
—
—
—
—
E04
Aux Fan Fault
Yes
Yes
Yes
To 284°F
To 284°F
To 284°F
E11
Excess Oven Temp
Yes
Yes
No
No
No
No
E13
Excess Steam Gen Temp
Yes
No
No
No
No
No
E15
Excess Condensate Temp
Yes
Yes
No
No
To 356°F
No
E21
Oven Probe Fault
Yes
Yes
212°F only
No
No
No
E22
Core Temp Probe Fault
Yes
Yes
Yes
Yes
Yes
Yes
E23
Steam Gen Probe Fault
Yes
No
Yes
Yes
Yes
Yes
E24
Bypass Probe Fault
Yes
Yes
To 210°F
No
Yes
No
E25
Condensate Probe Fault
Yes
Yes
Yes
To 356°F
To 356°F
To 320°F
E26
Steam Gen Safety Probe Fault
Yes
No
Yes
Yes
Yes
Yes
E27
Excess Steam Gen Safety Temp
Yes
No
No
No
No
No
E29
Probe Short to Frame
Yes
Yes
No
No
No
No
E34
DE (Drain) Pump Failure
Yes
No
Yes
Yes
Yes
Yes
E35
Venting Error
Yes
Yes
Yes
Yes
Yes
Yes
E36
Steam Temp High
No
Yes
No
No
Yes
No
E80
ID Error
Yes
Yes
Yes
Yes
Yes
Yes
E81
Program Memory Error
Yes
Yes
Yes
Yes
Yes
Yes
E82
WP Error
Yes
Yes
Yes
Yes
Yes
Yes
E83
Algo Error
Yes
Yes
Yes
Yes
Yes
Yes
E96
Connection Error
Yes
Yes
No
No
No
No
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
29
VENTLESS HOOD OPTION
®
COMBITHERM
The Ventless Hood option is factory installed directly on
the top of the Alto-Shaam Combitherm oven. The hood is
designed to vent clean air back into the kitchen, filtering
vapors and grease. A high-power fan draws steam and
fumes into the hood intake and out the top surface exhaust
vent. Fumes and vapors are circulated through filters
draining the condensation through a drain at the rear of the
hood. An activated charcoal filter cleans the air before
venting it out the top of the hood.
C O N D E N S AT E D R A I N
A ventless hood condensate drain line to the floor drain
must be installed. The 3/4" NPT thread connection is
found at the back of the hood. The drain line must always
be a positive gradient away from the Combitherm.
OPENING MECHANISM
Using a coin or screwdriver, turn to open;
reverse procedure to close and latch.
Hood and oven will not operate unless this is
closed properly.
ELECTRIC COMBITHERM
PG .
30
—
INSTALLATION MANUAL
#MN-28677
VENTLESS HOOD OPTION
®
COMBITHERM
O P E R AT I O N
� Turn the ventless hood power knob "ON".
� Wait five seconds, then press the "COMBI RESET" button.
� Turn the Combitherm oven power "ON".
There are a number of safety features incorporated into
the operation of the hood which are directly related to
the interaction of hood function and the operation of the
combi oven/steamer.
�
I N D I C AT O R L I G H T S
If the indicator lights do not illuminate, the filters may
be missing or not properly aligned. Check them for
proper positioning. Ventless hood and oven will not
operate unless the hood is closed properly.
�
INTERLOCK SWITCHES
CHARCOAL FILTER SWITCH , GREASE FILTER SWITCH :
Prevents hood and oven operation if any filter is not
in place or is improperly installed.
FAN PRESSURE SWITCH :
Prevents Combi oven operation if hood fan is not
operating or if the filters are more than 25% blocked.
T I M E D L AT C H I N G M E C H A N I S M
In order to evacuate steam and grease-laden air from
the oven interior, this mechanism prevents the
operator from fully opening the oven door for 25
ELECTRIC COMBITHERM
—
seconds to one minute. The mechanism
automatically disengages at the end of a pre-set time
allowing full door extension.
RESET SWITCH
The reset has to be used if the Combitherm oven is
turned on before the hood or if the hood was
opened. It resets the pressure switch circuit and
provides power to the Combitherm control circuit.
This switch must also be used to reset hood controls
after any problem with the filters, or the improper
latching of the ventless hood door.
INSTALLATION MANUAL
#MN-28677
PG .
31
VENTLESS HOOD OPTION
®
COMBITHERM
CHARCOAL FILTER
GREASE FILTER
FI-24114 (VHES-5)
FI-24102 (VHES-10)
FI-24113 (VHES-5)
FI-23062 (VHES-10)
CLEANING AND MAINTENANCE
G R E A S E F I LT E R S A N D M E TA L
HOUSING (PLENUM)
To ensure optimum performance from the ventless
hood, it is important to establish and maintain a
regular cleaning and maintenance schedule.
To help maintain the protective film coating on
polished stainless steel, clean the exterior of the
cabinet with a cleaner recommended for stainless
steel surfaces. Spray the cleaning agent on a clean
cloth and wipe with the grain of the stainless steel.
C H A R C O A L F I LT E R
The charcoal filter should be inspected for
contaminant's on a regular basis. Replacement must
be made at a minimum of three month intervals —
more often if heavy contaminant's are visible or if
the filter no longer controls odors.
To remove the filter, pull and slide out while holding
the bottom housing. When replacing the filter,
make certain the air flow arrow(s) point toward the
hood fan, and that the filter is replaced in the
three-sided metal frame provided with the hood.
ELECTRIC COMBITHERM
PG .
32
—
Cleaning frequency should be based on oven usage
with a maximum of two weeks between cleaning if
the oven is used for non-grease laden products or
steam applications only. Grease laden products such
as red meat, poultry, etc., require cleaning frequency
of at least once a week. Remove the grease filter by
pulling it straight out of the housing. Place the filter
in the dishwasher or wash separately by placing in
hot, soapy water until all grease and particles have
been removed. Rinse thoroughly. Allow the filter to
air dry before reinstalling.
Clean the interior metal housing (plenum) with a
damp cloth and any good commercial detergent or
grease solvent at the recommended strength. Avoid
the use of abrasive cleaning compounds, chloride
based cleaners, or cleaners containing quaternary
salts. Use a degreasing agent if necessary.
To replace the grease filter, the air flow arrow on
the filter casing should be pointing toward the
hood fan.
INSTALLATION MANUAL
#MN-28677
O R I G I N A L E Q U I P M E N T L I M I T E D WA R R A N T Y
®
COMBITHERM
Alto-Shaam, Inc. warrants to the original purchaser that any original part that is found to be defective in material or
workmanship will, at Alto-Shaam’s option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
The labor warranty remains in effect one (1) year from installation or fifteen (15) months from the shipping date,
whichever occurs first. Alto-Shaam will bear normal labor charges performed by an authorized Alto-Shaam service agent
during standard business hours, and excluding overtime, holiday rates or any additional fees.
The parts warranty remains in effect for one (1) year from installation or fifteen (15) months from the shipping date,
whichever occurs first.
THIS WARRANTY DOES NOT APPLY TO:
1. Replacement of light bulbs.
2. Equipment damage caused by accident, shipping, improper installation or alteration.
3. Steam generator or steam generating system damage as a result of inadequate routine maintenance and cleaning.
Required maintenance and cleaning of steam generating equipment is the responsibility of the owner/operator.
4. Equipment used under conditions of abuse, misuse, carelessness or abnormal conditions including, but not limited
to, equipment subjected to harsh or inappropriate chemicals including, but not limited to, compounds containing
chlorine, chlorides or quaternary salts, or equipment with missing or altered serial numbers.
5. Equipment that uses water must meet Alto-Shaam’s minimum water quality standards as shown below. USE OF
WATER NOT MEETING ALTO-SHAAM'S MINIMUM WATER QUALITY STANDARDS WILL VOID THIS WARRANTY.
Water quality and required maintenance of steam generating equipment is the responsibility of the owner/operator.
The installation and use of Alto-Shaam’s CombiGuard™ Water Filtration System is highly recommended.
ALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS
CONTAMINANT
INLET WATER REQUIREMENTS (UNTREATED WATER)
Free Chlorine
Less than 0.1 ppm (mg\L)
Hardness
Less than 3 gpg (52 ppm)
Chloride
Less than 30 ppm (mg\L)
pH
7.0 to 8.5
Alkalinity
Less than 50 ppm (mg\L)
Silica
Less than 12 ppm (mg\L)
Total Dissolved Solids (tds)
Less than 60 ppm
6. Damage caused by use of any cleaning agent other than Alto-Shaam’s Combitherm® Oven Cleaner including, but not
limited to, damage due to chlorine, bleach, quaternary salts, scouring powders or other harmful chemicals. Use of
Alto-Shaam’s Combitherm Cleaner on Combitherm ovens is highly recommended.
7. Any losses or damage resulting from malfunction, including loss of product or other consequential or incidental
damages of any kind.
8. Equipment modified in any manner from original model, substitution of parts other than factory authorized parts,
removal of any parts including legs, or addition of any parts.
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL ALTO-SHAAM BE LIABLE FOR LOSS OF USE, LOSS OF REVENUE OR PROFIT, OR LOSS OF PRODUCT, OR
FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
No person except an officer of Alto-Shaam, Inc. is authorized to modify this warranty or to incur on behalf of Alto-Shaam
any other obligation or liability in connection with Alto-Shaam equipment.
ELECTRIC COMBITHERM
—
INSTALLATION MANUAL
#MN-28677
PG .
33
T R A N S P O R TAT I O N D A M A G E A N D C L A I M S
®
COMBITHERM
All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the
carrier, such shipments become the property of the consignee.
Should damage occur in shipment, it is a matter between the carrier and the consignee.
In such cases, the carrier is assumed to be responsible for the safe delivery of the
merchandise, unless negligence can be established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in the truck or immediately after it is moved to the
receiving area. Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have made a proper count and inspection of all
merchandise received.
3. Note all damage to packages directly on the carrier ’s delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on the delivery receipt:
Driver refuses to allow inspection of containers for visible damage.
6. Telephone the carrier ’s office immediately upon finding damage, and request an inspection. Mail a written
confirmation of the time, date, and the person called.
7. Save any packages and packing material for further inspection by the carrier.
8. Promptly file a written claim with the carrier and attach copies of all supporting paperwork.
We will continue our policy of assisting our customers in collecting claims which have been properly filed and
actively pursued. We cannot, however, file any damage claims for you, assume the responsibility of any claims, or
accept deductions in payment for such claims.
RECORD THE MODEL AND SERIAL NUMBER OF THE APPLIANCE
FOR EASY REFERENCE. ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER
IN ANY CONTACT WITH ALTO-SHAAM REGARDING THIS APPLIANCE.
Model: ____________________________________________________
Serial Number: _____________________________________________
Date Installed: ______________________________________________
Voltage: ___________________________________________________
Purchased From: ____________________________________________
____________________________________________________
____________________________________________________
W164 N9221 Water Str eet
PHONE:
●
P. O . B o x 4 5 0
34
Menomonee Falls, Wisconsin 53052-0450
●
U.S.A.
262.251.3800 • 800.558-8744 USA/CANADA
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
www.alto-shaam.com
ELECTRIC COMBITHERM
PG .
●
Alto-Shaam has established a
twenty-four hour emergency service call
center to offer immediate customer access
to a local authorized service agency
outside of standard business hours. The
emergency service access is provided
exclusively for Alto-Shaam equipment
and is available throughout the United
States through the use of Alto-Shaam's
toll-free number. Emergency service
access is available seven days a week
including holidays.
—
INSTALLATION MANUAL
#MN-28677
Download PDF

advertising