Alto-Shaam 1200-TH/III Oven User Manual

®
Cooking & Holding Oven
Electronic Control
Model:
500-TH / I I I
750-TH / I I I
1000-TH / I I I
1200-TH / I I I
1200-TH/III
1000-TH/III
• I N STALLATION
• OPERATION
• MAI NTENANCE
500-TH/III
750-TH/III
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800 • 800.558.8744 USA / CANADA
FAX: 262.251.7067 • 800.329.8744 U . S . A .
www.alto-shaam.com
PRINTED IN U.S.A.
ONLY
MN-28679 • 04/08
®
DELIVERY
U N PA C K I N G
This Alto-Shaam appliance has been
thoroughly tested and inspected to insure only the
highest quality unit is provided. Upon receipt,
check for any possible shipping damage and report
it at once to the delivering carrier. See
Transportation Damage and Claims section
located in this manual.
This appliance, complete with unattached
items and accessories, may have been delivered in
one or more packages. Check to ensure that all
standard items and options have been received
with each model as ordered.
Save all the information and instructions
packed with the appliance. Complete and return
the warranty card to the factory as soon as
possible to assure prompt service in the event of a
warranty parts and labor claim.
This manual must be read and understood by
all people using or installing the equipment
model. Contact the Alto-Shaam service
department if you have any questions concerning
installation, operation, or maintenance.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
TH/III
1. Carefully remove the
appliance from the
carton or crate.
NOTE: Do not discard the
carton and other
packaging material
until you have
inspected the unit
for hidden damage
and tested it for
proper operation.
®
®
2. Read all instructions in this manual carefully
before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner or
manager of the business or to the person
responsible for training operators. Additional
manuals are available from the Alto-Shaam
service department.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
1
SAFETY PROCEDURES
AND PRECAUTIONS
Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.
DANGER
Used to indicate the presence of a
hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.
WA R N I N G
Used to indicate the presence of a
hazard that CAN cause personal injury,
possible death, or major property
damage if the warning included with
this symbol is ignored.
1. This appliance is intended to cook, hold or
process foods for the purpose of human
consumption. No other use for this appliance is
authorized or recommended.
2. This appliance is intended for use in commercial
establishments where all operators are familiar
with the purpose, limitations, and associated
hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
3. Any troubleshooting guides, component views,
and parts lists included in this manual are for
general reference only and are intended for use
by qualified technical personnel.
4. This manual should be considered a permanent
part of this appliance. This manual and all
supplied instructions, diagrams, schematics,
parts lists, notices, and labels must remain with
the appliance if the item is sold or moved to
another location.
CAUTION
Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.
CAUTION
NOTE
For equipment delivered for use
in any location regulated by the
following directive:
DO NOT DISPOSE OF ELECTIRCAL
OR ELECTRONIC EQUIPMENT WITH
OTHER MUNICIPAL WASTE.
Used to indicate the presence of a hazard that can
or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.
N O T E : Used to notify personnel of
installation, operation, or
maintenance information that is
important but not hazard related.
PG .
2
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
I N S TA L L AT I O N
DANGER
CAUTION
IMPROPER INSTALLATION,
ALTERATION, ADJUSTMENT,
SERVICE, OR MAINTENANCE COULD
RESULT IN SEVERE INJURY, DEATH
OR CAUSE PROPERTY DAMAGE.
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
CAUTION
TO PREVENT PERSONAL INJURY,
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN IN
OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
DANGER
DO NOT store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
S I T E I N S TA L L AT I O N
The Alto-Shaam cook
and hold oven must be
installed in a location
that will permit the
oven to function for its
intended purpose and
to allow adequate
clearance for
ventilation, proper
cleaning, and
maintenance access.
Emissions testing conducted by Underwriters
Laboratories, Inc. ® was found to be in
compliance with the applicable requirements of
NFPA96: 2004 Edition, Par. 4.1.1.2. U.L
emissions sampling of grease laden vapor
resulted in a total of 0.55 milligrams per cubic
meter with no visible smoke and is considered
representative of all oven models in the line.
Based on these results, hood installation and/or
outside venting should not be a requirement in
most areas. Verify local codes for locations
where more restrictive codes are applicable.
®
1. The oven must be installed on a stable and
level surface.
2. DO NOT install this appliance in any area
where it may be affected by any adverse
conditions such as steam, grease, dripping
water, high temperatures, or any other severely
adverse conditions.
3. DO NOT store or use any flammable liquids or
allow flammable vapors in the vicinity of this
oven or any other appliance.
4. This appliance must be kept free and clear of
any combustible materials.
5. This appliance must be kept free and clear of
any obstructions blocking access for
maintenance or service.
TH/III
MINIMUM CLEARANCE REQUIREMENTS
18" (457mm) minimum clearance at the back from heat
producing equipment. To protect the electronic
control, maintain sufficient side clearance to prevent
the control area from reaching any temperature at or
above 140°F (60°C).
NOTE
If the appliance has been unplugged for an
extended period of time, the Real Time
Clock may require recharging. Plug the unit
into the proper receptacle for a minimum of
24 hours.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
3
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
8-15/16"
(227mm)
500-TH/III
43-9/16" (1106mm)
40-5/16" (1023mm)
Electrical
Connection
25-1/8" (638mm)
30-3/8" (772mm)
27-13/16" (705mm)
with 3-1/2" Casters*
33-1/16" (839mm)
Electrical Connection
25-7/16" (646mm)
18-1/16" (458mm)
29-1/4" (743mm)
21" (532mm)
with optional bumper
with optional bumper
*32-1/16" (814mm) - with optional 2-1/2" casters
*34-5/16" (874mm) - with optional 5" casters
*34-11/16" (880mm) - with optional 6" legs
WEIGHT
NET:
SHIP :
PG .
4
150 lb (68 kg)
165 lb (75 kg)
EST .
EST .
TH/III
PRODUCT\PAN CAPACITY
40 lb (18 kg)
VOLUME MAXIMUM :
INSTALLATION / OPERATION / SERVICE MANUAL
30
MAXIMUM
QUARTS
(38
LITERS )
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
55-1/2" (1408mm) with optional bumper
53-9/16" (1360mm)
12-7/8"
(326mm)
Electrical
Connection
77-1/2" (1967mm) - Pass-Through Option
750-TH/III
33-5/8" (856mm)
Electrical
Connection
Pass-Through
Option
33-7/8" (860mm)
with optional bumper
25-1/8" (638mm)
Electrical Connection
27-7/8"
(708mm)
33-3/16" (843mm)
with 3-1/2" casters*
26-5/8"
(675mm)
30-7/16" (772mm)
30-15/16"
(785mm)
25-3/4"
(653mm)
33-7/8" (860mm)
with optional bumper
28-1/4" (716mm)
with optional bumper
*32-3/16" (817mm) - with optional 2-1/2" casters
*34-5/8" (878mm) - with optional 5" casters
*34-13/16" (884mm) - with optional 6" legs
WEIGHT
NET:
SHIP :
192 lb (87 kg)
212 lb (96 kg)
EST .
EST .
TH/III
PRODUCT\PAN CAPACITY
100 lb (45 kg)
VOLUME MAXIMUM :
INSTALLATION / OPERATION / SERVICE MANUAL
75
MAXIMUM
QUARTS
(95
LITERS )
PG .
5
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
1000-TH/III
72-3/8" (1838mm) Pass-Through Option
Electrical
Connection
50-1/16" (1272mm)
33-11/16" (856mm)
Electrical
Connection
Pass-Through
Option
33-7/8" (860mm)
with optional bumper
30-3/4" (780mm)
34-5/8" (878mm)
39-7/8" (1012mm)
with Standard 3-1/2" Casters*
22-5/8" (573mm)
25-1/16" (636mm)
with optional bumper
31-15/16" (811mm)
37-1/4" (945mm)
53-1/8" (1349mm) with optional bumper
11-1/4"
(284mm)
33-7/8" (860mm)
with optional bumper
*38-7/8" (987mm) - with optional 2-1/2" casters
*41-1/4" (1047mm) - with optional 5" casters
*41-1/2" (1053mm) - with optional 6" legs
WEIGHT
NET:
SHIP :
PG .
6
225 lb (102 kg)
233 lb (106 kg)
EST .
EST .
TH/III
PRODUCT\PAN CAPACITY
120 lb (54 kg)
VOLUME MAXIMUM :
INSTALLATION / OPERATION / SERVICE MANUAL
60
MAXIMUM
QUARTS
(76
LITERS )
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
1200-TH/III
33-3/8" (848mm)
Electrical
Connection
Electrical
Connection
Reach-In
53-1/8" (1349mm)
Pass-Through
Option
50-5/8" (1285mm)
72-1/16" (1830mm)
10-1/16"
(255mm)
33-7/8" (860mm)
22-9/16" (573mm)
Electrical
Conn.
66-1/8" (1679mm)
72-15/16" (1852mm)
75-9/16" (1918mm) with 5" (127mm) Casters*
Reach-In
25-1/16" (636mm)
WEIGHT
31-3/16" (791mm)
33-7/8" (860mm)
*74-3/16" (1883mm) - with optional 3-1/2" (89mm) casters
*
NET:
SHIP :
420 lb (191 kg)
475 lb (215 kg)
EST .
EST .
TH/III
PRODUCT\PAN CAPACITY ( P E R
120 lb (54 kg)
VOLUME MAXIMUM :
INSTALLATION / OPERATION / SERVICE MANUAL
60
COMPARTMENT)
MAXIMUM
QUARTS
(76
LITERS )
PG .
7
I N S TA L L AT I O N
OPTIONS AND ACCESSORIES
500-TH/III
Bumper, Full Perimeter
Carving Holder,
PRIME RIB
STEAMSHIP ( CAFETERIA ) ROUND
Casters - 2 RIGID, 2 SWIVEL W/BRAKE
5" (127mm)
3-1/2" (89mm)
2-1/2" (64mm)
Door with Window
RIGHT - HAND
LEFT - HAND
Door Lock with Key
Drip Pan
STANDARD WITH DRAIN ,
1-7/16"
1-11/16"
STANDARD WITH DRAIN , 1-7/8"
EXTRA DEEP , 2-7/16"
STANDARD WITH DRAIN ,
Legs, 6" (152mm), Flanged ( SET
Pan Grid, Wire - 18"
Pan Slides (230V
X
26"
ONLY )
Shelf, Stainless Steel
Stacking Hardware
(37mm)
(43mm)
(48mm)
(62mm)
OF FOUR )
PAN INSERT
FLAT WIRE , REACH - IN
RIB RACK
HACCP Network Options
➥ HACCP Documentation
➥ HACCP with Kitchen Management
* REFER TO HACCP SPECIFICATION #9015 FOR APPLICABLE
PG .
8
5006782
5004861
5005103
5005103
HL-2635
4459
HL-2635
4459
HL-2635
4459
HL-2635
4459
STANDARD
5004862
STANDARD
STANDARD
5004862
STANDARD
15855R
15857R
15433R
15732R
15879R
15881R
15879R
15881R
5008022
TH/III
5004862
5008022
5008022
5008017
––
LK-22567
LK-22567
LK-22567
LK-22567
14813
––
––
––
––
14831
––
1115
––
––
14824
1115
––
––
14824
1115
5004863
5004863
5004863
5004863
––
PN-2115
PN-2115
PN-2115
SH-2326
––
––
SH-2324
SH-2327
SH-2743
SH-2325
SH-2346
SH-2773
SH-2325
SH-2346
SH-2773
5008251
FLAT WIRE , PASS - THROUGH
750-TH/III 1000-TH/III 1200-TH/III
5004864
5008240
5004864
PART NUMBERS.
INSTALLATION / OPERATION / SERVICE MANUAL
––
5004864
––
––
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
STACKING INSTRUCTIONS
1) If the two appliances were shipped together from the factory, the top unit will have the
casters already removed. A stacking kit will be included with the shipment.
If casters need to be removed: lay the unit on its back, and remove the set screw on each caster. Pull the
casters out of the unit.
2) While appliance is laid on its back, insert one stacking post in each of the four corners of
the upper unit. Secure the stacking posts using one screw and two flat washers that come
with the stacking kit.
Note: The flange on the stacking posts must face the outside of the unit.
3) Remove the four top mounting screws from the lower unit. Place the upper appliance,
which has the stacking posts installed, on top of the bottom unit. Center the top unit from
front to back. Re-install the four screws through the flange of the four stacking posts.
STACKING
POSTS
CASTER SET SCREW
TOP
MOUNTING
SCREWS
TOP
MOUNTING
SCREWS
Stacking Configurations
1000-TH/III with 1000-TH/III or 1000-S
750-TH/III with 750-TH/III, 750-S, or 767-SK/III
500-TH/III with 500-TH/III or 500-S
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
9
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
A number of adjustments are associated with
initial installation and start-up. It is important
that these adjustments be conducted by a qualified
service technician. Installation and start-up
adjustments are the responsibility of the dealer or
user. These adjustments include but are not
limited to thermostat calibration, door adjustment,
leveling, electrical hook-up and installation of
optional casters or legs.
LEVELING
Level the oven
from side-to-side and front-toback with the use of a spirit level. For ovens
installed with casters, it is important that the
installation surface be level due to the probability
of frequent oven repositioning.
We recommend checking the level of the oven
periodically to make certain the floor has not
shifted nor the oven moved.
NOTE: Failure to properly level this oven can
cause improper function and will result in
the uneven baking with products
consisting of semi-liquid batter.
PG .
10
TH/III
RESTRAINT REQUIREMENTS
—MOBILE EQUIPMENT
WA R N I N G
RISK OF ELECTRIC SHOCK.
Appliance must be secured
to building structure.
Any appliance that is not furnished with a power
supply cord but that includes a set of casters must
be installed with a tether. Adequate means must
be provided to limit the movement of this
appliance without depending on or transmitting
stress to the electrical conduit. The following
requirements apply:
1. Maximum height of casters is 6" (152mm).
2. Two of the casters must of be the locking type.
3. Such mobile appliances or appliances on mobile
stands must be installed with the use of a flexible
connector secured to the building structure.
A mounting connector for a restraining device is
located on the lower back flange of the appliance
chassis or on an oven stand, approximately 18"
(457mm) from the floor. A flexible connector is not
supplied by nor is it available from the factory.
INSTALLATION / OPERATION / SERVICE MANUAL
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
D R I P T R AY I N S TA L L AT I O N I N S T R U C T I O N S
STANDARD DRIP PAN*
[BOTTOM OF OVEN INTERIOR • BELOW
SIDE-RACKS]
HANG DRIP TRAY ON SCREWS
DRIP
TRAY*
*SEE ALTO-SHAAM PARTS LIST FOR ALTO-SHAAM PART NUMBERS.
WA R N I N G
FAILURE TO PROPERLY INSTALL THE
DRIP TRAY CAN OR WILL CAUSE
MAJOR EQUIPMENT DAMAGE AND
WILL RESULT IN A LEAKAGE
HAZARD THAT CAN CAUSE
PERSONAL INJURY.
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
11
I N S TA L L AT I O N
ELECTRICAL CONNECTION
The appliance must be installed by a qualified
service technician. The oven must be properly
grounded in accordance with the National
Electrical Code and applicable local codes.
230V:
To prevent an electrical shock hazard between
the appliance and other appliances or metal
parts in close vicinity, an equalization-bonding
stud is provided. An equalization bonding lead
must be connected to this stud and the other
appliances / metal parts to provide sufficient
protection against potential difference.
The terminal is marked with the following
symbol.
Plug the unit into a properly grounded receptacle
ONLY, positioning the unit so that the plug is
easily accessible in case of an emergency. Arcing
will occur when connecting or disconnecting the
unit unless all controls are in the “ OFF ” position.
Proper receptacle or outlet configuration or
permanent wiring for this unit must be installed
by a licensed electrician in accordance with
applicable local electrical codes.
ELECTRICAL - 500-TH/III
VOLTAGE
120
208-240 ( UL )
at 208
at 240
230
PHASE
1
1
1
1
1
CYCLE / HZ
60
60
60
60
50
AMPS
16.0
11.2
10.6
12.2
12.0
ELECTRICAL - 750-TH/III
VOLTAGE
208-240 ( UL )
at 208
at 240
230
PHASE
1
1
1
1
CYCLE / HZ
60
60
60
50
AMPS
15.8
14.6
16.9
15
ELECTRICAL - 1000-TH/III
VOLTAGE
208-240 ( UL )
at 208
at 240
230
PHASE
1
1
1
1
ELECTRICAL -
60
60
60
50
AMPS
15.8
14.4
16.7
13.5
1200-TH/III
1.92
2.70
2.20
2.93
2.75
kW
3.80
3.04
4.05
3.0
kW
3.8
3.0
4.0
CORD
& PLUG
NEMA 5-20 P
20A-125 V PLUG
NO CORD
&
PLUG
CEE 7/7
220-230 V PLUG
CORD
& PLUG
NO CORD
&
PLUG
CEE 7/7
220-230 V PLUG
CORD
& PLUG
NO CORD
&
PLUG
2.7
CEE 7/7
220-230V PLUG
VOLTAGE
PHASE
CYCLE/ HZ
AMPS
kW
CORD & PLUG
at 208
1
60
28.9
6.0
& PLUG
1
50
28.7
6.6
208-240 (UL)
at 240
230
PG .
CYCLE / HZ
kW
NOTE: The appliance must be connected to an
electrical circuit that is protected by an
external GFCI outlet.
12
1
1
60
60
30
33.3
7.2
8.0
TH/III
DANGER
ELECTRICAL CONNECTIONS MUST
BE MADE BY A QUALIFIED SERVICE
TECHNICIAN IN ACCORDANCE WITH
APPLICABLE ELECTRICAL CODES.
DANGER
ENSURE POWER SOURCE
MATCHES VOLTAGE STAMPED
ON APPLIANCE NAMEPLATE.
DANGER
To avoid electrical shock, this
appliance MUST be adequately
grounded in accordance with local
electrical codes or, in the absence of
local codes, with the current edition
of the National Electrical Code
ANSI/NFPA No. 70. In Canada, all
electrical connections are to be
made in according with CSA C22.1,
Canadian Electrical Code Part 1 or
local codes.
NO CORD
NO CORD
& PLUG
INSTALLATION / OPERATION / SERVICE MANUAL
O P E R AT I N G I N S T R U C T I O N S
U S E R S A F E T Y I N F O R M AT I O N
CAUTION
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN IN
OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
The Alto-Shaam cook and hold oven is intended
for use in commercial establishments by qualified
operating personnel where all operators are
familiar with the purpose, limitations, and
associated hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
S T A R T- U P O P E R A T I O N
BEFORE INITIAL USE:
Interior oven surfaces must be heated to remove
surface oils and the accompanying odor produced
during the first use of the oven.
1. Wipe all wire shelves, side racks and the full
oven interior with a clean, damp cloth. Install
the oven side racks, oven shelves, and external
drip tray. Shelves are installed with the
curved edge toward the back of the oven.
Insert the drip pan on the interior bottom
surface of the oven.
2. •
•
•
•
3. • Press the TIME key.
• Press the up and down arrows to set the
cooking time to approximately 2 hours.
• Allow the oven to cycle for approximately
2 hours or until no odor is detected.
Close the oven doors.
Press and release control ON / OFF key.
Press the COOK key.
Press the up and down arrows to set the
cooking temperature to 300°F (149°C).
DANGER
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
13
O P E R AT I N G I N S T R U C T I O N S
Power ON
Indicator
햸햷
햹 햺 햻
햽
햳
햴
햵
햶
햾
햿
햲
헀
헂
헁
CONTROL FEATURES
1. ON / OFF Key
The O N /O FF control system key operates the
functions of the control panel. If there is any
power loss during operation, the O N /O FF indicator
light will flash. To clear, push key and release.
2. C OOK Key — Temperature rang e 200° to 325°F
(93° to 162°C)
Used to select cooking mode and to review the cook
temperature setting.
3. T IME Key — Maximum time 24 hours
Used to select cook time and to review set time.
4. PROBE Key — Temperature rang e 50° to 195°F
(10° to 91°C)
Used to select internal product probe temperature
mode and to review probe temperature setting.
5. H OLD Key — Temperature rang e 60° to 205°F
(15° to 96°C)
Used to select food holding mode and to review set
holding temperature.
6. Lock Ind icator
When illuminated, this symbol indicates settings
used in the cooking sequence are locked and
cannot be changed.
7. H alo H eat Ind icator
When the oven is preheating, the Halo Heat
indicator will illuminate during preheating and
remain steady until the oven reaches the set
cooking temperature. When the temperature has
stabilized, the indicator will illuminate periodically
as the oven calls for heat.
8. Oven Preheat Lig ht
Illuminates until the oven is preheated.
9. LED Display
10.
11.
12.
13.
14.
15.
16.
Indicates interior oven air temperature, internal
product probe temperature, time, or when used in
conjunction with other keys, will review
original cooking, holding and probe temperature
settings. The display will also indicate various
programming and diagnostic information.
Read y Ind icator Lig ht
Illuminates when the oven has finished preheating.
U P and D OWN A RROWS
Used to increase or decrease set time, including
cooking, holding and probe temperature settings.
STA RT Key
Used to initiate a selected mode sequence when
p re sse d a nd re le a se d . You may stop any mode of
operation by p re ssing a nd h o ld ing the S TART Key
until you hear a beep.
Green Ind icator Lig hts
Located within each function key, the green light
functions as an operator prompt indicating
additional operator action is required and also
identifies current mode of operation.
A mber Ind icator Lig hts
Located below the C OOK , T IME , P ROBE and H OLD
Keys, these indicators will illuminate to identify
the current mode of operation and allows the
operator to identify the information currently
shown in the LED display.
PRESET Prog ram Keys
Provides memory storage and operation of up to
eight operator set cooking programs for specific
products (A thru H). I enables locking abilities.
C A N CEL Key
Used to erase a program from memory storage.
IMPORTANT
Do not use the oven if the controls are not properly functioning. Refer to the Trouble Shooting Guide located in
this manual or call an authorized service technician.
PG .
14
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
O P E R AT I N G I N S T R U C T I O N S
AUDIBLE SIGNALS
OV EN BEEPIN G is used to indicate a Y ES or N O response to operator input.
Beeps also indicate mode C HANGES and E RROR conditions.
One brief beep indicates a Y ES (enabled) response to the information entered into the control.
Two brief beeps indicate a N O (disabled) response to the information entered into the control.
A beep that lasts for one second indicates an oven mode T RANSITION . Example: Preheat to Ready-Start.
Three brief beeps indicate the oven is in the R EADY mode for product loading and S TART - UP .
Four brief beeps indicate an existing F AULT condition. Refer to the Trouble Shooting section of this manual.
Beeper volume can be changed. With the control in the O FF mode, press and hold the D OWN A RROW Key until the display
exhibits one of the 4 volume levels (0 being O FF or the lowest, and 3 being the highest). After each change, the button must be
released and the display must clear before the procedure can be repeated to select a different volume level.
O P E R AT I N G F E AT U R E S & F U N C T I O N S
Turn the Oven Control Panel Off:
Press and hold the O N /O FF Key until the oven beeps. The O N /O FF
indicator light will go out.
Stop an Operation:
Press and hold the S TART Key for several seconds until the control
beeps, indicating the operation has been cancelled. The oven will
remain in a power-on state.
Arrow Keys:
Cook, Hold and Probe Temperature set points can be adjusted by 1°
when pressing the A RROW Keys. To change a set point more rapidly,
p re ss a nd h o ld the A RROW Key along with the key for the temperature
function, and the temperature changes in steps of 10°F or 5°C.
The Time setting is adjusted in increments of one minute by pressing
the A RROW Keys. To make adjustment in steps of ten minutes, p re ss
a nd h o ld the T IME Key and A RROW Key at the same time.
Probe Usage:
NOTE: When cooking by probe, insert the probe into the raw
product
a ft e r
t he
oven
ha s
be e n
p r e he a t e d .
WAIT ONE FULL MINUTE to allow the probe temperature to
decrease to the internal temperature of the product. Press the
s t a r t bu t t o n t o be g in t he c o o king p r o c e s s a ft e r t his p r o be
temperature adjustment period. A false probe reading of the
internal product temperature will cause the oven to default to a
holding temperature.
When the oven probe remains inserted in the probe bracket, the LED
temperature display will indicate the ambient air temperature inside
the oven. To use the probe for cooking remove it from the bracket
and wipe the full length of the metal probe with a disposable alcohol
pad to clean and sanitize before using.
Only the tip of the probe senses the internal product temperature;
therefore, it is important the tip be placed correctly in the product for
internal temperature accuracy. Push the probe tip halfway into the
product, positioning the tip at the center of the food mass. When
inserting the probe into solid foods such as meat roast or poultry
breasts, push the probe in from a straight downward position or in
from the side to the center position. If placing into a semi-liquid or
liquid product, the probe cable must be secured to keep the probe
positioned properly. Do not let the probe tip touch the edges, bottom
or side of a container. Tape the probe cable to the lip or edge of
the container.
TH/III
Display High/ Low Probe Temperatures:
To observe the recorded maximum or minimum
probe temperature when cooking by probe, press
the following keys while the probe remains in the
product:
Highest Temperature: Press P ROBE Key and U P
A RROW Key at same time.
Lowest Temperature: Press P ROBE Key and D OWN
A RROW Key at same time.
Halo Heat Indicator:
When the oven is preheating the Halo Heat
indicator light will remain illuminated until it
reaches the set cook temperature. Once the
temperature has stabilized, this indicator will
illuminate periodically as the oven calls for heat.
Green and Amber Indicators:
Each program key includes a green light which
indicates a requirement for additional
programming by the operator or the current
operational state of the oven.
The C OOK , T IME , P ROBE , and
H OLD keys include an amber
indicator light to identify the
information being displayed.
Green
Amber
Power Fail Detect:
If the power were to fail for any reason while
heating, the control will retain, in memory, the
programmed operating conditions. When power
is restored, the control will resume operating
from the point where it was interrupted and the
O N /O FF indicator light will flash, indicating that
such an event did occur. The operator can turn
off the flashing light by pressing the O N /O FF key.
N OTE : If s u c h an e v e n t h as o c c u r r e d , it is
strong ly recommend ed that you ensure the food is
safe for con su m p tion accord in g to local h e alth
reg ulations.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
15
O P E R AT I N G I N S T R U C T I O N S
Cook by Time: IS TH E MA IN ELECTRICA L POWER SWITCH ON ?
H ELPFUL H IN T
Press and release control ON / OFF key.
To avoid prolonged
• The green indicator light on the O N /O FF key will illuminate.
preheat
times between
• The oven will beep for one second.
loads,
leave the
• The oven will begin operating in the hold mode.
oven in the
• The amber hold indicator will illuminate.
hold mode.
• The previously set hold temperature will be displayed.
Press the H OLD Key.
➥ To change the hold temperature, press the U P or D OWN A RROW Keys.
N ote:
If the oven is being used for hot food holding only, adjust the
set holding temperature. Do no t press the C OOK , T IME , or P ROBE Keys.
Press C OOK Key to preheat.
• The green indicator light on the C OOK Key will
illuminate.
• Last set cooking temperature will be displayed.
➥ To change the cook temperature, press the U P or
D OWN A RROW Keys.
• The green indicator light on the T IME Key and on the
P ROBE Key alternately flash.
CAUTION
TO MAINTAIN SAFE TEMPERATURE
LEVELS, COLD FOOD FOR
RETHERMALIZATION OR REHEATING
MUST NEVER BE ADDED TO THE OVEN
WHILE HOT FOODS ARE BEING HELD.
Press T IME Key.
• The green indicator light on the T IME Key will illuminate.
• Last set time is displayed.
➥ To change the cook time, press the U P or D OWN A RROW Keys.
• The green indicator light on the T IME Key will illuminate.
• Halo Heat and Pre-Heat indicator will illuminate.
➥ The oven is automatically programmed to preheat to the cook temperature.
• The oven will beep when preheated and the preheat indicator light will go out.
• Both the Ready and Start indicator lights will flash.
➥ The set cook temperature will be maintained by the oven and appear in the display
while in the ready/start mode.
Load the food insid e oven and close the oven d oor.
N ote:
The oven will beep 3 times every 25 seconds until the oven is loaded and the
S TART Key pressed.
Press and release STA RT key.
COOK
• The oven will beep.
• The green indicators for power, cook, time, and start will illuminate.
• The display will alternate between showing the set cook temperature and the remaining time.
H OLD
• The oven will beep at the end of the timed cooking cycle.
• The green indicator for cook will remain illuminated.
• The display will alternate between showing the set hold temperature and the amount of
time the product has remained in the holding mode.
• The Ready indicator light will illuminate after 2 hours in the hold mode.
N ote: The ready indicator does not necessarily indicate a product-ready state. For best
results, the product must remain in the oven at the set holding temperature for the
minimum number of hours indicated in the individual cooking instructions.
• The oven will remain operating in the hold mode until the control O N /O FF Key is pressed.
PG .
16
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
Cook by Probe:
O P E R AT I N G I N S T R U C T I O N S
IS TH E MA IN ELECTRICA L POWER SWITCH ON ?
Press and release control ON / OFF Key.
• The green indicator light on the O N /O FF key will illuminate.
• The oven will beep for one second.
• The oven will begin operating in the hold mode.
TO MAINTAIN SAFE TEMPERATURE
• The amber hold indicator will illuminate.
LEVELS, COLD FOOD FOR
RETHERMALIZATION OR REHEATING
• The previously set hold temperature will be displayed.
MUST NEVER BE ADDED TO THE OVEN
Press the H OLD Key.
WHILE HOT FOODS ARE BEING HELD.
CAUTION
➥ To change the hold temperature, press the U P or D OWN A RROW Keys.
N ote: I f t h e o v e n i s b e i n g u s e d f o r h o t f o o d h o l d i n g o n l y , a d j u s t t h e s e t h o l d i n g
temperature. Do no t press the C OOK , T IME , or P ROBE keys.
Press C OOK Key to preheat.
• The green indicator light on the C OOK Key will illuminate.
• Last set cooking temperature will be displayed.
➥ To change the cook temperature, press the U P or D OWN A RROW Keys.
• The green indicator light on the T IME Key and on the P ROBE Key alternately flash.
Press PROBE Key.
• The green indicator light on the P ROBE Key will illuminate.
• Last set internal product temperature is displayed.
➥ To change the internal product temperature, press the U P or D OWN A RROW Keys.
• The green indicator light on the P ROBE Key will illuminate.
• Halo Heat and Pre-Heat indicator will illuminate.
➥ The oven is automatically programmed to preheat to the cook temperature.
• The oven will beep when preheated and the preheat indicator extinguished.
• Both the Ready and Start indicator lights will flash.
➥ The set cook temperature will be maintained by the oven and appear in the display
while in the ready/start mode.
Load the food inside oven. Remove probe from its bracket, wipe the probe tip with a disposable
alcohol pad and insert probe properly into the product. Close the oven door.
Note: Oven will beep 3 times every 25 seconds until oven is loaded and S TART Key pressed.
Press and release STA RT key.
COOK
• The oven will beep.
• The green indicators for power, cook, probe, and start will illuminate.
• The display will alternate between showing the probe temperature and the elapsed time.
HOLD
• The oven will beep when the set probe temperature has been reached.
• The green indicator for cook will remain illuminated.
• The display will alternate between showing the set hold temperature and the amount of
time the product has remained in the holding mode.
• Ready indicator light will illuminate after 2 hours in the hold mode.
N ote: The ready indicator does not necessarily indicate a product-ready state. For best
results, the product must remain in the oven at the set holding temperature for the
minimum number of hours indicated in the individual cooking instructions.
• The oven will remain operating in the hold mode until the control O N /O FF Key is pressed.
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
17
O P E R AT I N G I N S T R U C T I O N S
Preset Menu Keys:
Alto-Shaam Cook and Hold ovens allow the operator to set up to eight cooking programs. Each cooking program
can be preset in any program mode to cook by time or internal product temperature. Cooking programs are
recalled and stored using the PRESET Keys labeled "A through H." These keys, along with the key labeled "I" share
additional functions described in the "User Options" section of this manual.
Programming a Cooking Program
Prior to this procedure, make sure the oven is “OFF”. Select the food product to be programmed.
Press and release control ON/OFF key. The oven will beep for one second and power to the unit
will be indicated by an illuminated green indicator light located in the upper left corner of the
ON/OFF key. The oven will begin operating in the hold mode. The amber hold indicator will be
illuminated and the last set hold temperature will be displayed.
Press H OLD Key. To change the hold temperature, press the U P or D OWN
A RROW Keys.
Press C OOK Key. Oven preheat indicator will illuminate and the last set cooking temperature
is displayed. To change the cook temperature, press the U P or D OWN A RROW Keys.
To cook by time — press the T IME Key. Last set cooking time is displayed.
To change the set time, press the U P or D OWN A RROW Keys. The green Time
indicator will illuminate.
— or —
To cook by probe — press the PROBE Key. Last set internal product temperature is displayed.
To change the set temperature, press the UP or DOWN ARROW Keys. The green Probe indicator
will illuminate.
The oven preheat indicator will illuminate. Oven is now in the preheat mode and is
automatically programmed to preheat to the cook temperature.
PRESETS
A
Select a letter code for the product programmed by the previous steps. Press and hold the
selected PRESET key until you hear a brief, four second beep. The letter key program indicator
light will illuminate and the product programmed is now stored in memory for the specific letter
key pressed. Additional programs can be stored in the remaining PRESET Keys if not previously
programmed.
Note: The last PRESET Key used will be the oven cooking run sequence for the next product
to be programmed. Settings can be manually changed for the next product and an alternate
pre-programmed letter key selected.
Erasing a Cooking Program
To erase a program, the oven must be in either the power-up hold mode or in the preheat mode. The oven
cannot be running a Preset Menu program.
When the oven is in the power-up hold mode or in the preheat mode, press and hold both the CANCEL Key and
the appropriate letter PRESET Key to be erased. Hold both keys until the oven beeps and the program's indicator
light goes out to indicate the program has been erased.
IMPORTANT
After programming a specific product into memory in a programmable preset key,
it is very important to make a written permanent record of the product and the program letter
assigned. Menu card (PE-23384) is provided for this purpose.
PG .
18
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
O P E R AT I N G I N S T R U C T I O N S
Cook Using Preset Menu Keys:
Press and release control ON / OFF Key.
• The green indicator light on the O N /O FF key will illuminate.
• The oven will beep for one second.
• The oven will begin operating in the hold mode.
• The amber hold indicator will illuminate.
• The previously set hold temperature will be displayed.
• P RESET Keys with stored cooking programs will have green indicator illuminated.
PRESETS
A
Press Desired PRESET Key (A through H)
• Halo Heat and Pre-Heat indicator will illuminate.
➥ The oven is automatically programmed to preheat to the cook temperature programmed.
• The oven will beep when preheated and the preheat indicator will go out.
• Both the Ready and Start indicator lights will flash.
➥ The set cook temperature will be maintained by the oven and appear in the display
while in the ready/start mode.
Load the food inside oven. If cooking by probe, remove probe from its bracket, wipe the probe tip
with a disposable alcohol pad and insert probe properly into product. Close the oven door.
N ote: The oven will beep 3 times every 25 seconds until the oven is loaded and the
S TART key pressed.
Press and release STA RT Key.
COOK
• The oven will beep.
• The green indicators for power, cook, probe or time, and start will illuminate.
• If programmed to cook by time, the display will alternate between showing the set cook
temperature and the time remaining.
• If programmed to cook by probe, the display will alternate between showing the set cook
temperature and the elapsed time.
H OLD
• The oven will beep when the set probe temperature has been reached or set time has elapsed.
• The green indicator for cook will remain illuminated.
• The display will alternate between showing the set hold temperature and the
amount of time the product has remained in the holding mode.
• The Ready indicator light will illuminate after 2 hours in the hold mode.
N ote: The ready indicator does not necessary indicate a product-ready state. For best
results, the product must remain in the oven at the set holding temperature for the
minimum number of hours indicated in the individual cooking instructions.
• The oven will remain operating in the hold mode until the control O N /O FF Key is pressed.
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
19
O P E R AT I N G I N S T R U C T I O N S
USER OPTIONS
Lock
Indicator
Preset
Lock
PRESET Keys Lock and Unlock
PRESET Keys A through H can be locked in order to
prevent storing, altering or erasing a program.
To lock the PRESET Keys, press and hold the "I" Key until
the oven beeps. Release the “I” key. The green indicator
on the "I" key will illuminate. Oven PRESET Keys A
through H are now locked.
Note: Only the oven PRESET keys A through H are
affected by this lock-out in order to also allow the
oven to be used with the unprogrammed Cook,
Probe, or Hold modes.
To unlock the PRESET Keys, press and hold the CANCEL
Key along with the "I" Key until you hear a brief beep.
Release all keys. The green indicator on the "I" key will
extinguish. The oven preset keys are now unlocked.
Fahrenheit or Celsius Selection
With the control in the off mode,
press and hold the UP ARROW Key until the
display toggles between Fahrenheit and
Celsius. After each change the button must
be released. The display must clear before
the procedure can be repeated.
PG .
20
TH/III
Control Panel Lock and Unlock
The control panel can be locked at any time in order to
prevent inadvertent or accidental setting changes.
To lock the control panel, press and hold the UP ARROW
Key and then press the ON/OFF Key.
You will hear a brief beep and the panel lock
indicator will illuminate. Release all keys. The oven's
control panel is now locked.
Note: The control panel is now fully locked
with the exception of the ON/OFF Key and ARROW
keys. You will be unable to turn the oven control
off at this point.
To unlock the control panel, press and hold the DOWN
ARROW Key and then press the ON/OFF Key. You will
hear two brief beeps and the panel lock indicator will
extinguish. Release all keys. The panel is now unlocked
and ready for normal use.
Beeper Volume Selection
With the control in the off mode,
press and hold the DOWN ARROW Key
until the display shows one of the 4
volume levels (0 being OFF or the lowest,
and 3 being the highest). After each
change, the button must be released and
the display must clear before the
procedure can be repeated to select a
different volume level.
INSTALLATION / OPERATION / SERVICE MANUAL
O P E R AT I N G I N S T R U C T I O N S
General Holding Guideline
Chefs, cooks and other specialized food service
personnel employ varied methods of cooking. Proper
holding temperatures for a specific food product must
be based on the moisture content of the product,
product density, volume, and proper serving
temperatures. Safe holding temperatures must also
be correlated with palatability in determining the
length of holding time for a specific product.
Halo Heat maintains the maximum amount of product
moisture content without the addition of water, water
vapor, or steam. Maintaining maximum natural
product moisture preserves the natural flavor of the
product and provides a more genuine taste. In
addition to product moisture retention, the gentle
properties of Halo Heat maintain a consistent
temperature throughout the cabinet without the
necessity of a heat distribution fan, thereby
preventing further moisture loss due to evaporation
or dehydration.
When product is removed from a high temperature
cooking environment for immediate transfer into
equipment with the lower temperature required for
hot food holding, condensation can form on the
outside of the product and on the inside of plastic
containers used in self-service applications. Allowing
the product to release the initial steam and heat
produced by high temperature cooking can alleviate
this condition. To preserve the safety and quality of
freshly cooked foods, however, a maximum of 1 to 2
minutes must be the only time period allowed for the
initial heat to be released from the product.
Most Halo Heat Holding Equipment is provided with
a thermostat control between 60° and 200°F
(16° to 93°C). If the unit is equipped with vents, close
the vents for moist holding and open the vents for
crisp holding.
TH/III
H O L D I N G T E M P E R AT U R E R A N G E
MEAT
FAHRENHEIT
CELSIUS
BEEF ROAST — Rare
130°F
54°C
BEEF ROAST — Med/Well Done
155°F
68°C
BEEF BRISKET
160° — 175°F
71° — 79°C
CORN BEEF
160° — 175°F
71° — 79°C
PASTRAMI
160° — 175°F
71° — 79°C
PRIME RIB — Rare
STEAKS — Broiled/Fried
RIBS — Beef or Pork
130°F
54°C
140° — 160°F
60° — 71°C
160°F
71°C
VEAL
160° — 175°F
71° — 79°C
HAM
160° — 175°F
71° — 79°C
PORK
160° — 175°F
71° — 79°C
LAMB
160° — 175°F
71° — 79°C
CHICKEN — Fried/Baked
160° — 175°F
71° — 79°C
DUCK
160° — 175°F
71° — 79°C
TURKEY
160° — 175°F
71° — 79°C
GENERAL
160° — 175°F
71° — 79°C
FISH — Baked/Fried
160° — 175°F
71° — 79°C
LOBSTER
160° — 175°F
71° — 79°C
SHRIMP — Fried
160° — 175°F
71° — 79°C
120° — 140°F
49° — 60°C
160° — 175°F
71° — 79°C
80° — 100°F
27° — 38°C
EGGS —Fried
150° — 160°F
66° — 71°C
FROZEN ENTREES
160° — 175°F
71° — 79°C
HORS D'OEUVRES
160° — 180°F
71° — 82°C
PASTA
160° — 180°F
71° — 82°C
PIZZA
160° — 180°F
71° — 82°C
POULTRY
FISH/SEAFOOD
BAKED GOODS
BREADS/ROLLS
MISCELLANEOUS
CASSEROLES
DOUGH — Proofing
POTATOES
180°F
82°C
PLATED MEALS
140° — 165°F
60°— 74°C
SAUCES
140° — 200°F
60° — 93°C
SOUP
140° — 200°F
60° — 93°C
VEGETABLES
160° — 175°F
71° — 79°C
THE HOLDING TEMPERATURES LISTED ARE SUGGESTED
GUIDELINES ONLY. ALL FOOD HOLDING SHOULD BE BASED ON
INTERNAL PRODUCT TEMPERATURES . ALWAYS FOLLOW LOCAL
HEALTH ( HYGIENE ) REGULATIONS FOR ALL INTERNAL
TEMPERATURE REQUIREMENTS .
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
21
CARE AND CLEANING
CLEANING AND PREVENTIVE MAINTENANCE
PROTECTING STAINLESS STEEL SURFACES
It is important to guard against
corrosion in the care of
stainless steel surfaces.
Harsh, corrosive, or
inappropriate chemicals can
completely destroy the
protective surface layer of stainless steel.
Abrasive pads, steel wool, or metal implements
will abrade surfaces causing damage to this
protective coating and will eventually result in
areas of corrosion. Even water, particularly hard
water that contains high to moderate
concentrations of chloride, will cause oxidation
and pitting that result in rust and corrosion. In
addition, many acidic foods spilled and left to
remain on metal surfaces are contributing factors
that will corrode surfaces.
Proper cleaning agents, materials, and
methods are vital to maintaining the appearance
and life of this appliance. Spilled foods should be
removed and the area wiped as soon as possible
but at the very least, a minimum of once a day.
Always thoroughly rinse surfaces after using a
cleaning agent and wipe standing water as quickly
as possible after rinsing.
PG .
22
TH/III
CLEANING AGENTS
Use non-abrasive cleaning products designed for
use on stainless steel surfaces. Cleaning agents
must be chloride-free compounds and must not
contain quaternary salts. Never use hydrochloric
acid (muriatic acid) on stainless steel surfaces.
Always use the proper cleaning agent at the
manufacturer's recommended strength.
Contact your local cleaning supplier for
product recommendations.
CLEANING MATERIALS
The cleaning function can usually be accomplished
with the proper cleaning agent and a soft, clean
cloth. When more aggressive methods must be
employed, use a non-abrasive scouring pad on
difficult areas and make certain to scrub with the
visible grain of surface metal to avoid surface
scratches. Never use wire brushes, metal scouring
pads, or scrapers to remove food residue.
INSTALLATION / OPERATION / SERVICE MANUAL
CARE AND CLEANING
EQUIPME NT CARE
Under normal circumstances, this
oven should provide you with long
and trouble free service. There is no
preventative maintenance required,
however, the following Equipment
Care Guide will maximize the potential life and
trouble free operation of this oven.
The cleanliness and appearance of this equipment
will contribute considerably to operating efficiency
and savory, appetizing food. Good equipment that
is kept clean works better and lasts longer.
CLEAN DAILY
1. Disconnect unit from power
source, and let cool.
2. Remove all detachable items
such as wire shelves, side
racks, and drip pans. Clean
these items separately.
3. Wipe the interior metal surfaces
of the oven with a paper towel to
remove loose food debris.
4. Clean the interior metal surfaces of the cabinet
with a damp clean cloth or sponge and any good
commercial detergent.
NOTE: Avoid the use of abrasive cleaning
compounds, chloride based cleaners, or
cleaners containing quaternary salts. Never
use hydrochloric acid (muriatic acid) on
stainless steel.
5. Spray heavily soiled areas with a water soluble
degreaser and let stand for 10 minutes, then
remove soil with a plastic scouring pad.
6. Wipe control panel, door vents, door handles,
and door gaskets thoroughly since these areas
harbor food debris.
7. Rinse surfaces by wiping with sponge and clean
warm water.
8. Remove excess water with sponge and wipe dry
with a clean cloth or air dry. Leave doors open
until interior is completely dry. Replace side
racks and shelves.
9. Wipe door gaskets and control panel dry with a
clean, soft cloth.
10. Interior can be wiped with a sanitizing solution
after cleaning and rinsing. This solution must
be approved for use on stainless steel food
contact surfaces.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
TH/III
11. To help maintain the protective film coating on
polished stainless steel, clean the exterior of the
cabinet with a cleaner recommended for
stainless steel surfaces. Spray the cleaning
agent on a clean cloth and wipe with the grain
of the stainless steel.
12. Clean any glass with a window cleaner.
Always follow appropriate state or local health
(hygiene) regulations regarding all applicable
cleaning and sanitation requirements for equipment.
CLEAN THE DOOR VENTS
Door vents need to be inspected and cleaned
as required.
CLEAN THE PROBES DAILY
Remove all food soil from probes.
Wipe entire probe and cable
assembly with warm detergent
solution and a clean cloth.
Remove detergent by wiping
each probe and cable with clean
rinse water and a cloth. Wipe
probes and probe brackets with
disposable alcohol pad or sanitizing solution
recommended for food contact surfaces. Allow probe
and cable to air dry in probe holding bracket.
CHECK THE COOLING FAN IN THE OVEN
CONTROL AREA
While the oven is warm, check that the cooling fan in
the oven control area is functioning. The fan is located
at the back of the unit, toward the top.
CHECK OVERALL CONDITION OF
OVEN ONCE A MONTH
Check the oven once a month for physical damage and
loose screws. Correct any problems before they begin
to interfere with the operation of the oven.
DANGER
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DO NOT USE OVEN IF CONTROLS ARE NOT
PROPERLY FUNCTIONING
Refer to the Trouble Shooting Guide located in this
manual or call an authorized service technician.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
23
S A N I TAT I O N
Food flavor and aroma are usually so closely
related that it is difficult, if not impossible, to
separate them. There is also an important,
inseparable relationship between cleanliness and
food flavor. Cleanliness, top operating efficiency,
and appearance of equipment contribute
considerably to savory, appetizing foods.
Good equipment that is kept clean, works
better and lasts longer.
The most accurate method of measuring safe
temperatures of both hot and cold foods is by
internal product temperature. A quality
thermometer is an effective tool for this purpose,
and should be routinely used on all products that
require holding at a specific temperature.
A comprehensive sanitation program should focus
on the training of staff in basic sanitation
procedures. This includes personal hygiene,
proper handling of raw foods, cooking to a safe
internal product temperature, and the routine
monitoring of internal temperatures from receiving
through service.
Most food imparts its own particular aroma and
many foods also absorb existing odors.
Unfortunately, during this absorption, there is no
distinction between GOOD and BAD odors. The
majority of objectionable flavors and odors
troubling food service operations are caused by
bacteria growth. Sourness, rancidity, mustiness,
stale or other OFF flavors are usually the result of
germ activity.
The easiest way to insure full, natural food flavor is
through comprehensive cleanliness. This means
good control of both visible soil (dirt) and invisible
soil (germs). A thorough approach to sanitation
will provide essential cleanliness. It will assure an
attractive appearance of equipment, along with
maximum efficiency and utility. More importantly,
a good sanitation program provides one of the key
elements in the prevention of food-borne illnesses.
A controlled holding environment for prepared
foods is just one of the important factors involved
in the prevention of food-borne illnesses.
Temperature monitoring and control during
receiving, storage, preparation, and the service of
foods are of equal importance.
Most food-borne illnesses can be prevented
through proper temperature control and a
comprehensive program of sanitation. Both these
factors are important to build quality service as the
foundation of customer satisfaction. Safe food
handling practices to prevent food-borne illness is
of critical importance to the health and safety of
your customers.
HACCP, an acronym for Hazard Analysis (at)
Critical Control Points, is a quality control program
of operating procedures to assure food integrity,
quality, and safety. Taking steps necessary to
augment food safety practices are both cost
effective and relatively simple. While HACCP
guidelines go far beyond the scope of this manual,
additional information is available by contacting:
CENTER FOR FOOD SAFETY AND APPLIED
NUTRITION FOOD AND DRUG ADMINISTRATION
1-888-SAFEFOOD
INTERNAL FOOD PRODUCT TEMPERATURES
HOT FOODS
DANGER ZONE
40° TO 140°F
(4° TO 60°C)
CRITICAL ZONE
70° TO 120°F
(21° TO 49°C)
SAFE ZONE
140° TO 165°F
(60° TO 74°C)
COLD FOODS
DANGER ZONE
SAFE ZONE
ABOVE 40°F
(ABOVE 4°C)
36°F TO 40°F
(2°C TO 4°C)
FROZEN FOODS
PG .
24
DANGER ZONE
ABOVE 32°F
(ABOVE 0°C)
CRITICAL ZONE
0° TO 32°F
(-18° TO 0°C)
SAFE ZONE
0°F or below
(-18°C or below)
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
SERVICE
TROUBLE SHOOTING
Error
Code
E-10
E-11
E-20
Possible Cause
Service Required
Description/Results
Air Sensor Fault (shorted)
Air sensor is shorted.
Ino p e ra tiv e Ov e n Air sensor defective? See following page for air sensor test.
Air Sensor Fault (open)
Air sensor is open or connection failure.
Ino p e ra tiv e Ov e n Air sensor defective? See following page for air sensor test.
Product Probe Fault (shorted)
Ov e n w ill co o k in tim e o nly
E-21
Product Probe Fault (open)
Ov e n w ill co o k in tim e o nly
E-30
Under temperature
Oven w ill no t reach set tem p erature
E-31
E-60
Product probe is shorted
Probe defective? See following page for probe sensor test.
Product Probe is open or connection failure.
Probe defective? See following page for probe sensor test.
Oven door closed? Door gasket need replacement? Preheat skipped?
Oven overloaded or has frozen product? Defective air sensor or probe?
Defective solid state relay? Bad wire connections or open heating cable?
Is the high limit switch tripped? If none of the above, call service.
Shorted cable? Defective solid state relay? Defective air sensor?
Over temperature
Ov e n w ill sh ut d o w n If none of the above, call service.
Control must be replaced.
Real time clock error
Ino p e ra tiv e Ov e n This error also is displayed if the unit has been unplugged for more than 30
days. If this is the case the unit should be plugged in with the circuit breaker
on and the unit displaying the E-60 on the front panel for more than 30
minutes. Once this has been accomplished the circuit breaker should be
turned to off or the unit unplugged for about 10 seconds after which the unit
should be turned on again. This may have to be repeated.
E-70
Check control connections for loose wires. If none, control must be replaced.
Configuration connector error
Ino p e ra tiv e Ov e n
E-78
Voltage low
Ino p e ra tiv e Ov e n
If 125 VAC unit, voltage is below 90 VAC. Correct.
If 208-240 VAC voltage is below 190 VAC. Correct.
If 125 VAC unit, voltage is over 130 VAC. Correct.
Ino p e ra tiv e Ov e n If 208-240 VAC, voltage is over 250 VAC. Correct.
E-79
Voltage high
E-80
Contact Service.
EEPROM - Function data error
Ino p e ra tiv e Ov e n
E-82
E-84
E-86
Contact Service.
EEPROM - Calibration data error
Ino p e ra tiv e Ov e n
Contact Service.
EEPROM - Unit ID error
Ino p e ra tiv e Ov e n
Contact Service.
EEPROM - Preset data error
Ino p e ra tiv e Ov e n
CAUTION
THIS SECTION IS PROVIDED FOR THE ASSISTANCE
OF QUALIFIED SERVICE TECHNICIANS ONLY AND
IS NOT INTENDED FOR USE BY UNTRAINED OR
UNAUTHORIZED SERVICE PERSONNEL.
TH/III
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
25
SERVICE
This section is provided for the assistance of qualified technicians only and is not intended for use by
untrained or unauthorized service personnel. If your Alto-Shaam® unit is not operating properly, check the
following before calling your Authorized Alto-Shaam® Service Agent:
☛ Check the power flow to the unit. Plug in outlet? Circuit breaker switch at back of unit turned on?
Do not attempt to repair or service the Cook and Hold unit beyond this point. Contact Alto-Shaam® for
the nearest authorized service agent. Repairs made by any other service agents without prior
authorization by Alto-Shaam® will void the warranty on the unit.
TROUBLE SHOOTING INTERNAL ELECTRICAL COMPONENTS
A. No power. Display will not light.
1. Verify that power is available at the outlet or junction box.
2. Verify that the circuit breaker switch on the back of the unit is turned on.
3. Verify that the power cord is not open. Check continuity with a VOM meter.
4. If none of the above steps help, call a qualified service technician or refer to the Service Manual for
this particular oven.
B. Display is lit and unit calls for heat, but unit is not heating;
Error Code E30
Check to verify that the high limit switch located at the rear of the unit top has not been
tripped. If it has been tripped, reset by pressing in the hit limit reset button at the rear
of the oven.
After resetting, the cause of the high limit trip must be corrected. If the high limit switch
will not reset, the high limit switch is defective and must be replaced. This is a safety
d evice and must not be jumped out or rem oved from the circuit.
C. To test air sensor:
Test air sensor by placing sensor in ice water bath and using an ohmmeter set on the ohm scale. The
reading should be 100 ohms resistance. If it is more than 2 ohms higher or lower, sensor needs to
be replaced.
D. To test probe sensor:
Test food probe by placing in ice water bath and using an ohmmeter set on the ohm scale. The reading
should be 100 ohms resistance.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
CAUTION
THIS SECTION IS PROVIDED FOR THE ASSISTANCE
OF QUALIFIED SERVICE TECHNICIANS ONLY AND
IS NOT INTENDED FOR USE BY UNTRAINED OR
UNAUTHORIZED SERVICE PERSONNEL.
NOTE
If the appliance has been unplugged for an
extended period of time, the Real Time
Clock may require recharging. Plug the unit
into the proper receptacle for a minimum of
24 hours.
PG .
26
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
SERVICE
EXTERIOR SERVICE VIEW - 1200-TH/III
Control
Panel Overlay
PE-26714
Bonnet Cover, Top
1003887
Control Panel Bezel
PE-26567
Door Hinge
HG-22338
Bonnet Assembly
5005031
Probe
Assembly
15892
Panel, Back
1003704
Door Assembly
( RIGHT - HAND )
15415
Panel, Side
1003742
Shelf
SH-2325
Drip Pan
14824
Door Handle
with Latch
HD-27080
Door Gasket
GS-22952
Drip Tray Location
1007588
Side Rack
SR-2266
Casters, 5"
5004862
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
27
SERVICE
EXTERIOR SERVICE VIEW - 500-, 750-, 1000-TH/III
Bonnet Assembly
500 - 5006075
750 - 5004770
1000 - 5005031
Bonnet Cover, Top
500 - 1003889
Control
750 - 1003888
Panel Overlay
1000 - 1003887
500 - PE-26710
750 - PE-26839
1000 - PE-26714
Control Panel Bezel
500 - PE-26565
750 - PE-26566
1000 - PE-26567
Panel, Back
500 - 1007197
750 - 1006731
1000 - 1003704
Door Hinge
HG-22338
Panel, Side
500 - 1003681
750 - 1003682
1000 - 1003706
Door Assembly
500 - 15848
750 - 15730
1000 - 15415
Probe
Assembly
15892
Shelf
500 - SH-2326
750 - SH-2324
1000 - SH-2325
Drip Pan
500 - 14813
750 - 14831
1000 - 14824
Door Handle
with Latch
HD-27080
Drip Tray
500 - 1007267
750 - 1004710
1000 - 1004314
Side Rack
500 - SR-2386
750 - SR-2303
1000 - SR-2266
Casters, 3-1/2"
5008017
PG .
28
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
Door Gasket
500 - GS-22950
750 - GS-22951
1000 - GS-22952
SERVICE
E X T E R I O R S E R V I C E V I E W - PA R T S L I S T
PART DESCRIPTION
QTY.
500-TH/III
750-TH/III
1000-TH/III
1200-TH/III
2. Bonnet Cover, Top
1
1003889
1003888
1003887
1003887
1. Bonnet Assembly
1
3. Capillary Guard
4. Casters - 2 RIGID, 2 SWIVEL W/BRAKE
3-1/2" (89mm)
5" (127mm)
5. Control Panel Bezel
1
2
1
1
6. Control Panel Overlay
SET
RIGHT - HAND
LEFT - HAND
8. Drip Pan
10. Gasket, Door
12. Hinge, Door
13. Panel, Back
14. Panel, Sides
15. Probe Assembly
16. Shelf, Stainless Steel
Pan Slides (230V only)
1
2
5008017
––
1493
––
5008017
––
5005031
––
1493
––
5004862
PE-26566
––
PE-26567
––
––
PE-26567
1
2
1
2
15848
––
15853
––
15730
––
15429
––
15415
––
15721
––
––
15415
––
15721
1
1007267
1004710
1004314
1007588
1
2
11. Handle, Door
5008017
––
1493
––
5005031
PE-26565
––
1
2
9. Drip Tray
1493
––
5004770
1
2
1
7. Door Assembly, Slab
17. Side Rack
SET
5006075
1
2
PAIR
PAIR
1
2
1
2
2
3
6
2
4
2
PE-26710
14813
––
GS-22950
––
14831
––
GS-22951
––
PE-26714
14824
––
GS-22952
––
PE-26714
––
14824
––
GS-22952
HD-27080
––
HD-27080
––
HD-27080
––
––
HD-27080
1007197
1006731
1003704
1003704
HG-22338
––
1003681
15892
––
SH-2326
––
––
SR-2386
––
5008251
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
TH/III
PE-26839
HG-22338
––
1003682
15892
––
––
SH-2324
––
SR-2303
––
5008240
HG-22338
––
1003706
15892
––
––
SH-2325
––
SR-2266
––
––
––
HG-22338
1003742
––
15892
––
––
SH-2325
––
SR-2266
––
DANGER
LOCK-OUT OR POST
B R E A K E R PA N E L U N T I L
SERVICE WORK HAS
BEEN COMPLETED.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
29
SERVICE
ELECTRONIC COMPONENTS
Note: Unit shown is 1000-TH/III, 208V
Terminal Block
BK-33546
Unit Front
Beeper
BP-3567
Control Assembly
CC-34194
Fan
FA-3974
Relay
RL-33829
Heat Sink
1005836
Terminal
Block
BK-33546
Power Supply
Board
BA-33554
Voltage Monitor
Board
BA-33764
Hi-Limit
Reset Button
Circuit Breaker Switch
SW-34077
Terminal Block, Power
BK-3019
Hi-Limit
Thermostat
TT-33476
PG .
30
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
Ground Screw
SC-2190
SERVICE
E L E C T R O N I C C O M P O N E N T S PA R T S L I S T
PART DESCRIPTION
1. Beeper
Beeper, 1200-TH/III
2. Circuit Board
3. Circuit Breaker Switch
Circuit Breaker Switch, 1200-TH/III
4. Control Assembly
5. Cordset, 230V (NOT SHOWN)
Cordset, 120V (NOT SHOWN)
6. Fan, Box
Fan Box, 120V (500-TH/III ONLY)
QTY.
1
2
PART NUMBER
1
1
1
BA-33991
SW-34077
SW-34076
1
1
CD-3922
CD-3397
1
1
1
7. Ground Screw
8. Heat Sink
9. Heat Sink Pad (not shown)
10. Power Supply Board
11. Reed Switch (NOT SHOWN)
Reed Switch, 1200-TH/III
12. Relay
Relay, 1200-TH/III
14. Sensor Mounting Block
Sensor Mounting Block, 1200-TH/III
15. Terminal Block, Power
16. Terminal Block
Terminal Block, 1200-TH/III
17. Thermostat, Fan
19. Voltage Monitor Board
FA-3974
FA-3973
1
2
SW-33559
1
2
SN-33541
1
BK-3019
1
2
BA-33554
RL-33829
BK-24427
2
4
BK-33546
1
TT-33476
1
18. Thermostat, Hi-Limit
CC-34194
SC-2190
1005836
HE-33926
1
2
13. Sensor
Sensor, 1200-TH/III
BP-3567
1
1
1
1
1
C A B L E H E AT I N G
SERVICE KITS
TT-33255
BA-33764
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
No. 4880
MODEL 500-TH/III
includes:
CB-3045
CR-3226
IN-3488
BU-3105
BU-3106
ST-2439
NU-2215
SL-3063
TA-3540
Cable Heating Element . . . . 134 feet
Ring Connector. . . . . . . . . . . . . . . . 4
Insulation Corner . . . . . . . . . . 1 foot
Shoulder Bushing . . . . . . . . . . . . . . 4
Cup Bushing . . . . . . . . . . . . . . . . . . 4
Stud . . . . . . . . . . . . . . . . . . . . . . . . 4
Hex Nut . . . . . . . . . . . . . . . . . . . . . 8
Insulating Sleeve . . . . . . . . . . . . . . 4
Electrical Tape . . . . . . . . . . . . . 1 roll
MODELS
includes:
CB-3045
CR-3226
IN-3488
BU-3105
BU-3106
ST-2439
NU-2215
SL-3063
TA-3540
No. 4881
750-, 1000-TH/III
Cable Heating Element . . . . 210 feet
Ring Connector . . . . . . . . . . . . . . . 12
Insulation Corner . . . . . . . . . . 1 foot
Shoulder Bushing . . . . . . . . . . . . . 12
Cup Bushing . . . . . . . . . . . . . . . . . 12
Stud. . . . . . . . . . . . . . . . . . . . . . . . 12
Hex Nut . . . . . . . . . . . . . . . . . . . . 24
Insulating Sleeve . . . . . . . . . . . . . 12
Electrical Tape . . . . . . . . . . . . . 1 roll
No. 4881
MODEL 1200-TH/III
includes:
CB-3045
CR-3226
IN-3488
BU-3105
BU-3106
ST-2439
NU-2215
SL-3063
TA-3540
( ONE
KIT PER CAVITY )
Cable Heating Element . . . . 210 feet
Ring Connector . . . . . . . . . . . . . . . 12
Insulation Corner . . . . . . . . . . 1 foot
Shoulder Bushing . . . . . . . . . . . . . 12
Cup Bushing . . . . . . . . . . . . . . . . . 12
Stud. . . . . . . . . . . . . . . . . . . . . . . . 12
Hex Nut . . . . . . . . . . . . . . . . . . . . 24
Insulating Sleeve . . . . . . . . . . . . . 12
Electrical Tape . . . . . . . . . . . . . 1 roll
DANGER
LOCK-OUT OR POST
B R E A K E R PA N E L U N T I L
SERVICE WORK HAS
BEEN COMPLETED.
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
31
PG .
32
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
33
PG .
34
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
35
PG .
36
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
37
PG .
38
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
TH/III
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
39
TRANSPORTATION
DAMAGE and CLAIMS
All Alto-Shaam equipment
is sold F.O.B. shipping
point, and when accepted
by the carrier, such
shipments become the
property of the consignee.
Should damage occur in shipment, it is a matter
between the carrier and the consignee. In such cases, the
carrier is assumed to be responsible for the safe delivery
of the merchandise, unless negligence can be established
on the part of the shipper.
1.
2.
3.
4.
5.
6.
7.
8.
Make an immediate inspection while the equipment
is still in the truck or immediately after it is moved to
the receiving area. Do not wait until after the
material is moved to a storage area.
Do not sign a delivery receipt or a freight bill until
you have made a proper count and inspection of all
merchandise received.
Note all damage to packages directly on the carrier’s
delivery receipt.
Make certain the driver signs this receipt. If he
refuses to sign, make a notation of this refusal on
the receipt.
If the driver refuses to allow inspection, write the
following on the delivery receipt:
D r iv e r re fu s e s t o al lo w in s p e c t i o n o f
c o n t a in e r s fo r vi si bl e d a ma ge .
Telephone the carrier’s office immediately upon
finding damage, and request an inspection. Mail
a written confirmation of the time, date, and the
person called.
Save any packages and packing material for further
inspection by the carrier.
Promptly file a written claim with the carrier and
attach copies of all supporting paperwork.
We will continue our policy of assisting our
customers in collecting claims which have been properly
filed and actively pursued. We cannot, however, file any
damage claims for you, assume the responsibility of any
claims, or accept deductions in payment for such claims.
®
LIMITED
WARRANTY
Alto-Shaam, Inc. warrants to the original purchaser that any
original part that is found to be defective in material or workmanship
will, at Alto-Shaam's option, subject to provisions hereinafter stated, be
replaced with a new or rebuilt part.
The labor warranty remains in effect one (1) year from installation
or fifteen (15) months from the shipping date, whichever occurs first.
Alto-Shaam will bear normal labor charges performed during standard
business hours, and excluding overtime, holiday rates or any
additional fees.
The parts warranty remains in effect for one (1) year from
installation or fifteen (15) months from the shipping date, whichever
occurs first.
However, the heating element on Halo Heat ® cook/hold ovens
and the refrigeration compressor on Alto-Shaam Quickchillers ™ are
warranted for a period of five (5) years from installation. The labor
warranty is the same as stated above; namely, for one (1) year from
installation or fifteen (15) months from the shipping date, whichever
occurs first.
THIS WARRANTY DOES NOT APPLY TO:
1. Calibration.
2. Replacement of light bulbs and/or the replacement of display
case glass due to damage of any kind.
3. Equipment damage caused by accident, shipping, improper
installation or alteration.
4. Equipment used under conditions of abuse, misuse, carelessness
or abnormal conditions including, but not limited to, equipment
subjected to harsh or inappropriate chemicals including, but not
limited to, compounds containing chloride or quaternary salts, poor
water quality, or equipment with missing or altered serial numbers.
5. Damage incurred as a direct result of poor water quality,
inadequate maintenance of steam generators and/or surfaces
affected by water quality. Water quality and required maintenance
of steam generating equipment is the responsibility of the
owner/operator.
6. Damage caused by use of any cleaning agent other than
Alto-Shaam's Combitherm ® Cleaner including, but not limited to,
damage due to chlorine or other harmful chemicals. Use of
Alto-Shaam's Combitherm ® Cleaner on Combitherm ® ovens is
highly recommended.
7. Any losses or damage resulting from malfunction, including loss
of product or consequential or incidental damages of any kind.
8. Equipment modified in any manner from original model,
substitution of parts other than factory authorized parts,
removal of any parts including legs, or addition of any parts.
This warranty is exclusive and is in lieu of all other warranties,
expressed or implied, including the implied warranties of
merchantability and fitness for a particular purpose. In no event
shall Alto-Shaam be liable for loss of use, loss of revenue or profit,
or loss of product, or for any indirect or consequential damages.
No person except an officer of Alto-Shaam, Inc. is authorized to modify
this warranty or to incur on behalf of Alto-Shaam any other obligation
or liability in connection with Alto-Shaam equipment.
ALTO- SHAAM, IN C .
RECORD THE MODEL AND SERIAL NUMBER OF THE APPLIANCE FOR EASY REFERENCE.
ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER IN ANY CONTACT WITH ALTO-SHAAM REGARDING THIS APPLIANCE.
Model: _______________________________________________Date Installed: __________________________________________________________
Voltage: ______________________________________________ Purchased From: _______________________________________________
Serial Number: _______________________________________ _______________________________________________________________________
W 1 6 4 N 9 2 2 1 Wa t e r S t r e e t
PHONE:
●
P. O . B o x 4 5 0
●
Menomonee Falls, Wisconsin 53052-0450
●
U.S.A.
262.251.3800 • 800.558-8744 USA/CANADA
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
www.alto-shaam.com
PRINTED IN U.S.A.