User`s manual | AMD 7ZX-1 Computer Hardware User Manual

7ZX-1
TM
AMD Athlon /Duron
TM
Socket A Motherboard
USER'S MANUAL
AMD AthlonTM/DuronTM Socket A Processor Motherboard
REV. 1.01 First Edition
R-101-01-001211
FCC Compliance Statement:
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
Responsible Party Name: G.B.T. INC.
Address: 18305 Valley Blvd., Suite#A
LA Puent, CA 91744
Phone/Fax No: (818) 854-9338/ (818) 854-9339
hereby declares that the product
Product Name: Mother Board
Model Number: GA-7ZX
Conforms to the following specifications:
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),
Class B Digital Device
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
and
(2) this device must accept any inference received, including
that may cause undesired operation.
Representative Person's Name:
Signature:
Date:
This equipment has been tested and found to comply with limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television equipment reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
ERIC LU
Eric Lu
-Reorient or relocate the receiving antenna
Jun. 30, 2000
-Move the equipment away from the receiver
-Plug the equipment into an outlet on a circuit different from that to which the receiver is connected
-Consult the dealer or an experienced radio/television technician for additional suggestions
You are cautioned that any change or modifications to the equipment not expressly approve by the party
responsible for compliance could void Your authority to operate such equipment.
This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1) this
device may not cause harmful interference and 2) this device must accept any interference received, including
interference that may cause undesired operation.
Declaration of Conformity
We, Manufacturer/Importer
(full address)
G.B.T. Technology Träding GMbH
Ausschlager Weg 41, 1F, 20537 Hamburg, Germany
declare that the product
( description of the apparatus, system, installation to which it refers)
Mother Board
GA-7ZX
is in conformity with
(reference to the specification under which conformity is declared)
in accordance with 89/336 EEC-EMC Directive
EN 55011
Limits and methods of measurement
of radio disturbance characteristics of
industrial, scientific and medical (ISM
high frequency equipment
EN 61000-3-2*
EN60555-2
Disturbances in supply systems caused
by household appliances and similar
electrical equipment “Harmonics”
EN55013
Limits and methods of measurement
of radio disturbance characteristics of
broadcast receivers and associated
equipment
EN61000-3-3*
EN60555-3
Disturbances in supply systems caused
by household appliances and similar
electrical equipment “Voltage fluctuations”
EN 55014
Limits and methods of measurement
of radio disturbance characteristics of
household electrical appliances,
portable tools and similar electrical
apparatus
EN 50081-1
Generic emission standard Part 1:
Residual, commercial and light industry
EN 50082-1
Generic immunity standard Part 1:
Residual, commercial and light industry
EN 55015
Limits and methods of measurement
of radio disturbance characteristics of
fluorescent lamps and luminaries
EN 55081-2
Generic emission standard Part 2:
Industrial environment
EN 55020
Immunity from radio interference of
broadcast receivers and associated
equipment
EN 55082-2
Generic immunity standard Part 2:
Industrial environment
EN 55022
Limits and methods of measurement
of radio disturbance characteristics of
information technology equipment
ENV 55104
Immunity requirements for household
appliances tools and similar apparatus
DIN VDE 0855
part 10
part 12
Cabled distribution systems; Equipment
for receiving and/or distribution from
sound and television signals
EN 50091- 2
EMC requirements for uninterruptible
power systems (UPS)
CE marking
(EC conformity marking)
The manufacturer also declares the conformity of above mentioned product
with the actual required safety standards in accordance with LVD 73/23 EEC
EN 60065
Safety requirements for mains operated
electronic and related apparatus for
household and similar general use
EN 60950
Safety for information technology equipment
including electrical business equipment
EN 60335
Safety of household and similar
electrical appliances
EN 50091-1
General and Safety requirements for
uninterruptible power systems (UPS)
Manufacturer/Importer
Signature
(Stamp)
Date : Jun. 30, 2000
Name :
Rex Lin
:
Rex Lin
Table Of Content
SUMMARY OF FEATURES................................................................................................................................ 2
7ZX-1 MOTHERBOARD LAYOUT ................................................................................................................... 3
CPU SPEED SETUP ............................................................................................................................................. 4
CONNECTORS..................................................................................................................................................... 5
GAME & AUDIO PORT ......................................................................................................................................... 5
COM A / COM B / LPT PORT ............................................................................................................................ 5
USB 1 CONNECTOR ............................................................................................................................................ 5
USB 2 CONNECTOR ............................................................................................................................................ 6
PS/2 KEYBOARD & PS/2 MOUSE CONNECTOR ................................................................................................... 6
J3: CPU FAN ....................................................................................................................................................... 6
JP6: POWER FAN ................................................................................................................................................. 7
J2: SYSEM FAN .................................................................................................................................................... 7
ATX POWER ........................................................................................................................................................ 7
FLOPPY PORT....................................................................................................................................................... 8
IDE1(PRIMARY), IDE2(SECONDARY) PORT ........................................................................................................ 8
J15: AUX_IN...................................................................................................................................................... 8
J18: CD AUDIO LINE IN ...................................................................................................................................... 9
J13: RING POWER ON (INTERNAL MODEM CARD WAKE UP) .............................................................................. 9
J12: WAKE ON LAN ........................................................................................................................................... 9
JP8 / LED1: STR LED CONNECTOR & DIMM LED........................................................................................ 10
J4: IR ................................................................................................................................................................ 10
PANEL AND JUMPER DEFINITION .............................................................................................................. 11
J11: 2X11 PINS JUMPER ..................................................................................................................................... 11
JP16 /JP17/JP18: AMR (PRIMARY OR SECONDARY) SELECT (OPTIONAL) ........................................................ 11
JP4: REAR USB DEVICE WAKE UP SELECTION (USB CONNECTOR USB1) .................................................. 12
JP7: STR FUNCTION ENABLED (SUSPEND TO RAM) ........................................................................................ 12
JP9: ONBOARD SOUND FUNCTION SELECTION (OPTIONAL) .............................................................................. 12
JP11: FRONT USB DEVICE WAKE UP SELECTION (USB PORT USB2).......................................................... 13
JP10: BIOS WRITE PROTECTION (OPTIONAL)................................................................................................... 13
JP3: CLEAR CMOS FUNCTION (OPTIONAL)...................................................................................................... 13
BAT1: BATTERY ................................................................................................................................................ 14
PERFORMANCE LIST ..................................................................................................................................... 15
BLOCK DIAGRAM............................................................................................................................................ 16
SUSPEND TO RAM INSTALLATION............................................................................................................. 17
A.2 STR FUNCTION INSTALLATION ................................................................................................................... 17
A.3 HOW TO PUT YOUR SYSTEM INTO STR MODE?............................................................................................ 17
A.4 HOW TO RECOVER FROM THE STR SLEEP MODE?........................................................................................ 19
A.5 NOTICES: .................................................................................................................................................... 19
MEMORY INSTALLATION ............................................................................................................................. 20
BIOS SETUP........................................................................................................................................................ 21
ENTERING SETUP ......................................................................................................................................... 21
CONTROL KEYS ............................................................................................................................................ 21
GETTING HELP.............................................................................................................................................. 21
THE MAIN MENU............................................................................................................................................... 22
STANDARD CMOS SETUP ................................................................................................................................. 23
BIOS FEATURES SETUP ..................................................................................................................................... 25
FIGURE 3: BIOS FEATURES SETUP .................................................................................................................... 25
CHIPSET FEATURES SETUP ................................................................................................................................. 26
POWER MANAGEMENT SETUP ........................................................................................................................... 28
i
PNP/PCI CONFIGURATIONS ............................................................................................................................... 30
LOAD BIOS DEFAULTS ...................................................................................................................................... 31
LOAD SETUP DEFAULTS ..................................................................................................................................... 32
INTEGRATED PERIPHERALS ................................................................................................................................ 33
HARDWARE MONITOR ....................................................................................................................................... 36
SET SUPERVISOR / USER PASSWORD.................................................................................................................. 37
IDE HDD AUTO DETECTION ........................................................................................................................... 38
SAVE & EXIT SETUP .......................................................................................................................................... 39
EXIT WITHOUT SAVING ..................................................................................................................................... 40
APPENDIX: ACRONYMS................................................................................................................................. 41
ii
7ZX-1 Motherboard
Revision History
Revision
1.01
Revision Note
Initial release of the 7ZX-1 motherboard
user’s manual.
Date
Dec.2000
The author assumes no responsibility for any errors or omissions that may appear in this
document nor does the author make a commitment to update the information contained herein.
Third-party brands and names are the property of their respective owners.
DEC. 11, 2000 TAIPEI, TAIWAN, R.O.C
1
7ZX-1 Motherboard
Summary Of Features
Form Factor
CPU
Chipset
Clock Generator
Memory
I/O Control
Slots
On-Board IDE
30.5 cm x 22.8 cm ATX size form factor, 4 layers PCB.
AMD AthlonTM/DuronTM (K7) Socket A Processor
256K/64K L2 cache on die
Supports 500MHz ~ 1GHz and faster
Apollo KT133 ,consisting of:
VT8363 Memory/AGP/PCI Controller(PAC)
VT82C686A PCI Super-I/O Integrated Peripheral
Controller
(PSIPC)
ICS 9248-141 or ICW W230H
3 168-pin DIMM sockets
Supports PC-100 / PC-133 SDRAM
Supports up to 1.5GB DRAM
Supports only 3.3V SDRAM DIMM
VT82C686A
1 AGP slot supports 4X mode & AGP 2.0 compliant
5 PCI slots supports 33MHz & PCI 2.2 compliant
1 AMR (Audio Modem Riser) slot
Supports PIO mode 3, 4, UDMA33/ATA66 IDE & ATAPI
CD-ROM
2 IDE bus master (UDMA 33/ ATA 66) IDE ports for up
to 4 ATAPI devices
1 floppy port supports 2 FDD with 1.4M bytes
1 parallel ports supports Normal/EPP/ECP mode
2 serial ports (COM A & COM B)
4 USB ports
1 IrDA connector for IR
CPU/System fan revolution detect
CPU/System temperature detect
System voltage detect
CPU overheat shutdown detect
PS/2 Keyboard interface and PS/2 Mouse interface
AC’97 CODEC
Line In / Line Out / Mic In / AUX In / CD In / TEL / Game Port
Licensed AMI BIOS, 2M bit flash ROM
Support Wake-On-LAN (WOL)
Support Internal / External Modem Ring On
Support USB KB/MS Wake up from S3-S5
Includes 3 fan power connectors
Poly fuse for keyboard over-current protection
Support STR (Suspend-To-RAM) function
On-Board
Peripherals
Hardware
Monitor
PS/2 Connector
On-Board Sound
BIOS
Additional
Features
2
7ZX-1 Motherboard
7ZX-1 Motherboard Layout
JP4
J3
ATX POWER
USB1
PS/2
JP6
LPT
COM A
Socket A CPU
FLOPPY
COM B
JP8
J15
LED1
JP7
IDE2
IDE1
DIMM3
DIMM2
7ZX-1
DIMM1
J18
GAME & AUDIO
VT8363
AGP 1
SW1
Clock
Generator
AD1881
PCI1
PCI2
BAT1
VT82C
686A
J13
PCI3
JP3
J12
JP10
PCI4
J2
PCI5
BIOS
JP16 AMR
USB2
J4
JP17
BZ1
3
J11
JP11
JP9
JP18
7ZX-1 Motherboard
CPU Speed Setup
The system bus speed is selectable at 100~133MHz. The user can select the system bus speed by DIP switch
SW1.
Set System Bus Speed
zIf your clock generator (in Motherboard) is ICS 9248-141. You can follow the below reference.
ICS
9248-141
SW1: (ICS 9248-141)
O : ON, X : OFF
FSB
95
Ë100
105
110
113
115
117
133
3
X
X
O
O
O
X
O
X
1
O
X
X
O
X
X
X
X
2
O
O
O
X
X
X
X
X
4
O
X
X
X
O
O
X
X
zIf your clock generator (in Motherboard) is ICW W230H. You can follow the below reference.
SW1: (ICW W230H)
FSB
95
Ë100
102
104
106
108
110
112
133
W230H
1
O
0
0
X
0
0
0
0
0
O : ON, X : OFF
2
O
X
0
X
X
0
X
0
X
3
X
X
0
X
X
X
0
0
0
Ë The FSB Speed of the VIA KT133 is 100MHz.
0AMD CPU Heat Sink Installation:
Beware: Please check that the heat sink is in good contact with the CPU before you turn on your system.
The poor contact will cause over heat, and might cause damage to your processor.
4
4
X
X
X
0
0
0
0
0
X
Connectors
Connectors
Game & Audio Port
Game
Port
Line Out 1
MIC In
Line In
COM A / COM B / LPT Port
LPT Port
COM A
COM B
USB 1 Connector
1 2 34
5 67 8
Pin No.
1
2
3
4
5
6
7
8
Definition
USB V0
USB D0USB D0+
GND
USB V1
USB D1USB D1+
GND
5
Connectors
USB 2 Connector
2
10
1
9
Pin No.
1
2
3
4
5
6
7
8
9
10
Definition
+5V
GND
USB D2NC
USB D2+
USB D3+
NC
USB D3GND
+5V
PS/2 Keyboard & PS/2 Mouse Connector
PS/2
Mouse/Keyboard
Pin No. Definition
1
Data
5
6
2
NC
3
4
3
GND
4
VCC(+5V)
2
1
5
Clock
PS/2 Keyboard
6
NC
PS/2 Mouse
J3: CPU Fan
1
Pin No. Definition
1
Control
2
+12V
3
SENSE
6
7ZX-1 Motherboard
JP6: Power Fan
1
Pin No. Definition
1
Control
2
+12V
3
NC
J2: Sysem Fan
1
Pin No. Definition
1
Control
2
+12V
3
SENSE
ATX Power
10 20
1 11
Pin No.
Definition
3,5,7,13,
GND
15-17
1,2,11
3.3V
4,6,19,20
VCC
10
+12V
12
-12V
18
-5V
8
Power Good
9
5V SB stand by+5V
14
PS-ON(Soft On/Off)
7
Connectors
Floppy Port
Red Line
FDD1
IDE1(Primary), IDE2(Secondary) Port
Red Line
IDE 1 IDE 2
J15: AUX_IN
1
Pin No.
1
2
3
4
Definition
AUX-L
GND
GND
AUX-R
8
7ZX-1 Motherboard
J18: CD Audio Line In
1
Pin No.
1
2
3
4
Definition
CD-L
GND
GND
CD-R
J13: Ring Power On (Internal Modem Card Wake Up)
1
Pin No. Definition
1
Signal
2
GND
J12: Wake On LAN
1
Pin No. Definition
1
+5V SB
2
GND
3
Signal
9
Connectors
JP8 / LED1: STR LED Connector & DIMM LED
STR LED Connector External.
1
+
DIMM LED
J4: IR
1
Pin No.
Definition
1
VCC (+5V)
2
NC
3
IR Data Input
4
GND
5
IR Data Output
10
7ZX-1 Motherboard
Panel And Jumper Definition
J11: 2x11 Pins Jumper
GN
SPK
HD
RE
1
1
1
1
P−P−P+
GN (Green Switch)
GD (Green LED)
HD (IDE Hard Disk Active
LED)
SPK (Speaker Connector)
RE (Reset Switch)
P+P−P−(Power LED)
PW (Soft Power Connector)
GD
PW
Open: Normal Operation
Close: Entering Green Mode
Pin 1: LED anode(+)
Pin 2: LED cathode(−)
Pin 1: LED anode(+)
Pin 2: LED cathode(−)
Pin 1: VCC(+)
Pin 2- Pin 3: NC
Pin 4: Data(−)
Open: Normal Operation
Close: Reset Hardware System
Pin 1: LED anode(+)
Pin 2: LED cathode(−)
Pin 3: LED cathode(−)
Open: Normal Operation
Close: Power On/Off
Not available at the case
For external speaker in the case
JP16 /JP17/JP18: AMR (Primary or Secondary) Select (Optional)
(AMR
Audio Modem Riser)
1
1
1
JP17
JP16
JP18
Onboard AC97
AMR (Primary)
Onboard AC97+MR
(Secondary)
(Default)
JP16
ON
OFF
ON
JP17
1-2
3-4
1-2
3-4
11
JP18
1-2
3-4
1-2
Panel and Jumper Definition
JP4: Rear USB Device Wake up Selection (USB Connector USB1)
1
Pin No.
Definition
1-2 Close Normal (Default)
2-3 Close USB Device Wake up
USB1
(If you want to use "USB Dev Wakeup From S3-S5"
function, you have to set the BIOS setting "USB Dev
Wakeup From S3-S5" enabled, and the jumper "JP4"
enabled).
*(Power on the computer and as soon as memory
counting starts, press <Del>. You will enter BIOS Setup.
Select the item "POWER MANAGEMENT SETUP", then
select "USB Dev Wakeup From S3-S5: Enabled".
Remember to save the setting by pressing "ESC" and
choose the "SAVE & EXIT SETUP" option.)
JP7: STR Function Enabled (Suspend To RAM)
1
Pin No.
Open
Close
Definition
Normal (Default)
STR Enabled
JP9: Onboard Sound Function Selection (Optional)
JP9
1
Pin No.
Definition
1-2 close Onboard Sound
Enable (Default)
2-3 close Onboard Sound
Disable
12
7ZX-1 Motherboard
JP11: Front USB Device Wake up Selection (USB Port USB2)
1
USB2
Pin No.
Definition
1-2 close Normal (Default)
Enabled Front USB Device
2-3 close
Wake up
(If you want to use "USB Dev Wakeup From S3-S5"
function, you have to set the BIOS setting "USB Dev
Wakeup From S3-S5" enabled, and the jumper "JP11"
enabled).
*(Power on the computer and as soon as memory
counting starts, press <Del>. You will enter BIOS Setup.
Select the item "POWER MANAGEMENT SETUP", then
select "USB Dev Wakeup From S3-S5: Enabled".
Remember to save the setting by pressing "ESC" and
choose the "SAVE & EXIT SETUP" option.)
JP10: BIOS Write Protection (Optional)
1
Pin No.
Definition
ON
Write Protect Enable
Write Protect Disable
OFF
(Default)
Please Set Jumper JP10 to ”OFF” to enabled
BIOS Write Function when you update new BIOS
or new device
JP3: Clear CMOS Function (Optional)
1
Pin No.
Definition
1-2 close Normal (Default)
2-3 close
Clear CMOS
13
Panel and Jumper Definition
BAT1: Battery
+
CAUTION
☞ Danger of explosion if battery
is incorrectly replaced.
☞ Replace only with the same or
equivalent type recommended
by the manufacturer.
☞ Dispose of used batteries
according to the manufacturer’s
instructions.
14
Performance List
Performance List
The following performance data list is the testing results of some popular benchmark testing programs.
These data are just referred by users, and there is no responsibility for different testing data values gotten by
users. (The different Hardware & Software configuration will result in different benchmark testing results.)
• CPU
AMD ThunderbirdTM 950MHz, AMD DuronTM 700MHz
• DRAM
(256x1) MB SDRAM (HYUNDAI HYM71V733201)
• CACHE SIZE
256 KB included in Thunderbird
64 KB included in Duron
• DISPLAY
GA-GF2560
• STORAGE
Onboard IDE (Quantum KA13600AT)
• O.S.
TM
Windows NT 4.0 SPK6a
Display Driver at 1024 x 768 65536 colors 75Hz.
TUCD 1.5 Beta3
• DRIVER
AMD
Processor
ThunderbirdTM
950MHz
(100x9.5)
AMD DuronTM
700MHz (100x7)
Winbench99
CPU mark 99
86.5
61.5
FPU Winmark 99
5210
3840
Business Disk Winmark
99
5410
5440
Hi-End Disk Winmark 99
13600
13200
Business Graphics
Winmark 99
481
352
Hi-End Graphics Winmark
99
985
676
Winstone99
Business Winstone 99
47.3
40.3
Hi-End Winstone 99
50.8
41.6
If you wish to maximize the performance of your system, please refer to the detail on P.43
15
7ZX-1 Motherboard
Block Diagram
100MHz
Socket A
AGP
2X/4X
System Bus 100MHz
VT8363
3.3V SDRAM
100 / 133MHz
66MHz
100 / 133MHz
100 / 133MHz
66MHz
33MHz
ICS 9248-141
or ICW W230H
33MHz
5 PCI
ATA66 IDE
Channels
33MHz
14.318MHz
4 USB Ports
48MHz
VT82C
686A
Game Port
COM Ports
LPT Ports
IR Floppy
AC97
CODEC
AMR
PS/2
16
Suspend to RAM Installation
Suspend To RAM Installation
A.1 Introduce STR function:
Suspend-to-RAM (STR) is a Windows 98 ACPI sleep mode function. When recovering from STR (S3) sleep
mode, the system is able, in just a few seconds, to retrieve the last “state” of the system before it went to sleep
and recover to that state. The “state” is stored in memory (RAM) before the system goes to sleep. During STR
sleep mode, your system uses only enough energy to maintain critical information and system functions,
primarily the system state and the ability to recognize various “wake up” triggers or signals, respectively.
A.2 STR function Installation
Step 1:
(If you want to use STR Function, please set jumper JP7 Closed.)
1
Pin No.
Open
Close
Definition
Normal (Default)
STR Enabled
Step 2:
Power on the computer and as soon as memory counting starts, press <Del>. You will enter BIOS Setup. Select
the item “POWER MANAGEMENT SETUP”, then select “ACPI Sleep Type : S3 / STR”. Remember to save
the settings by pressing "ESC" and choose the “SAVE & EXIT SETUP” option.
Congratulation! You have completed the installation and now can use the STR function.
A.3 How to put your system into STR mode?
1.
There are two ways to accomplish this:
Choose the “Stand by” item in the “Shut Down Windows” area.
A. Press the “Start” button and then select “Shut Down”
17
Suspend to RAM Installation
B. Choose the “Stand by” item and press “OK”
2.
Define the system ”power on” button to initiate STR sleep mode:
A. Double click “My Computer” and then “Control Panel”
B. Double click the “ Power Management” item.
18
7ZX-1 Motherboard
C. Select the “Advanced” tab and “Standby” mode in Power Buttons.
D. Restart your computer to complete setup.
Now when you want to enter STR sleep mode, just momentarily press the “Power on”
button.
A.4 How to recover from the STR sleep mode?
There are five ways to “wake up” the system:
1.
2.
3.
4.
5.
Press the “Power On” button.
Use the “Resume by Alarm” function.
Use the “Modem Ring On” function.
Use the “Wake On LAN” function.
Use the “USB Device Wake Up” function.
A.5 Notices:
1.
In order for STR to function properly, several hardware and software requirements must be satisfied:
A.
Your ATX power supply must comply with the ATX 2.01 specification (provide more than 720 mA 5V
Stand-By current).
B. Your SDRAM must be PC-100 / PC-133 compliant.
2.
Jumper JP8 is provided to connect to the STR LED in your system chassis. [Your chassis may not provide
this feature.] The STR LED will be illuminated when your system is in STR sleep mode.
STR LED Connector External.
1
+
DIMM LED
19
7ZX-1 Motherboard
Memory Installation
The motherboard has 3 dual inline memory module (DIMM) sockets. The BIOS will automatically detects memory
type and size. To install the memory module, just push it vertically into the DIMM Slot .The DIMM module can only
fit in one direction due to the two notch. Memory size can vary between sockets.
Install memory in any combination table:
DIMM
DIMM
1
DIMM
2
DIMM
3
168-pin SDRAM DIMM Modules
X 1 pcs
Supports 16 / 32 / 64 / 128 / 256 / 512 MB
X 1 pcs
Supports 16 / 32 / 64 / 128 / 256 / 512 MB
X 1 pcs
Supports 16 / 32 / 64 /128 / 256 / 512 MB
Total System Memory (Max 1.5GB)
20
7ZX-1 Motherboard
BIOS Setup
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic
system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup
information when the power is turned off.
ENTERING SETUP
Power ON the computer and press <Del> immediately will allow you to enter Setup. If the message disappears
before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or
pressing the "RESET" bottom on the system case. You may also restart by simultaneously press <Ctrl> − <Alt>−
<Del> keys.
CONTROL KEYS
<↑>
<↓>
<←>
<→>
<Esc>
<+/PgUp>
<-/PgDn>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
Move to previous item
Move to next item
Move to the item in the left hand
Move to the item in the right hand
Main Menu - Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu - Exit
current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Reserved
Reserved
Reserved
Restore the previous CMOS value from CMOS, only for
Option Page Setup Menu
Load the default CMOS value from BIOS default table, only
for Option Page Setup Menu
Load the Setup Defaults
Reserved
Reserved
Save all the CMOS changes, only for Main Menu
GETTING HELP
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for
the highlighted item. To exit the Help Window press <Esc>.
21
BIOS Setup
The Main Menu
Once you enter AMI BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. The Main
Menu allows you to select from nine setup functions and two exit choices. Use arrow keys to select among the
items and press <Enter> to accept or enter the sub-menu.
AMIBIOS SIMPLE SETUP UTILITY-VERSION 1.23
( C ) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
HARDWARE MONITOR SETUP
CHIPSET FEATURES SETUP
SUPERVISOR PASSWORD
POWER MANAGEMENT SETUP
USER PASSWORD
PNP/PCI CONFIGURATION
IDE HDD AUTO DETECTION
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit
↑↓←→ : Select Item (Shift) F2 : Change Color
F5 : Old Values
F6 : Load BIOS Defaults
F7: Load Setup Defaults
F10: Save & Exit
Time, Date, Hard Disk Type, …
Figure 1: Main Menu
• Standard CMOS Setup
This setup page includes all the items in standard compatible BIOS.
• BIOS Features Setup
This setup page includes all the items of AMI special enhanced features.
• Chipset Features Setup
This setup page includes all the items of chipset special features.
• Power Management Setup
This setup page includes all the items of Green function features.
• PnP/PCI Configurations
This setup page includes all the configurations of PCI & PnP ISA resources.
• Load BIOS Defaults
Bios Defaults indicates the value of the system parameter which the system would be in the safe
configuration.
• Load Setup Defaults
Setup Defaults indicates the value of the system parameter which the system would be in the most
appropriate configuration.
• Integrated Peripherals
This setup page includes all onboard peripherals.
• Hardware Monitor Setup
This setup page is auto detect fan and temperature status.
• Supervisor password
Change, set, or disable password. It allows you to limit access to the system and Setup,
or just to Setup.
22
7ZX-1 Motherboard
• User password
Change, set, or disable password. It allows you to limit access to the system.
• IDE HDD auto detection
Automatically configure hard disk parameters.
• Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
• Exit Without Saving
Abandon all CMOS value changes and exit setup.
Standard CMOS Setup
The items in Standard CMOS Features Menu (Figure 2) are divided into 9 categories. Each category includes no,
one or more than one setup items. Use the arrows to highlight the item and then use the <PgUp> or <PgDn> keys
to select the value you want in each item.
AMIBIOS SETUP – STANDARD CMOS SETUP
( C ) 1999 American Megatrends, Inc. All Rights Reserved
Date (mm/dd/yyyy) : Tue Jan 25, 2000
Time (hh/mm/ss) : 10:36:24
TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
Pri Master : Auto
Pri Slave : Auto
Sec Master : Auto
Sec Slave : Auto
Floppy Drive A: 1.44 MB 3 ½
Floppy Drive B: Not Installed
Boot Sector Virus Protection : Disabled
Month: Jan – Dec
Day: 01 – 31
Year : 1990– 2099
Base Memory : 640 Kb
Other Memory: 384 Kb
Extended Memory: 127Mb
Total Memory: 128Mb
ESC : Exit
↑↓ : Select Item
PU/PD/+/– : Modify
(Shift)F2 : Color
Figure 2: Standard CMOS Setup
• Date
The date format is <Week> <Month> <Day>, <Year>.
Week
Month
Day
Year
The week, from Sun to Sat, determined by the BIOS and is
display-only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1990 through 2099
• Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time
clock. For example, 1 p.m. is 13:00:00.
• Primary Master, Slave / Secondary Master, Slave
The category identifies the types of hard disk from drive C to F that has been installed in the computer. There
are two types: auto type, and user definable type. User type is user-definable; Auto type which will
automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will not work properly
if you enter improper information for this category.
If you select User Type, related information will be asked to enter to the following items. Enter the information
directly from the keyboard and press <Enter>. Such information should be provided in the documentation
23
BIOS Setup
form your hard disk vendor or the system manufacturer.
CYLS.
Number of cylinders
HEADS
number of heads
PRECOMP
write precomp
LANDZONE Landing zone
SECTORS
number of sectors
If a hard disk has not been installed select NONE and press <Enter>.
• Floppy Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.
None
360K, 5.25 in.
1.2M, 5.25 in.
720K, 3.5 in.
1.44M, 3.5 in.
2.88M, 3.5 in.
No floppy drive installed
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-type high-density drive; 1.2M byte
capacity (3.5 inch when 3 Mode is Enabled).
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity.
3.5 inch double-sided drive; 2.88M byte capacity.
• Boot Sector Virus Protection
If it is set to enable, the category will flash on the screen when there is any attempt to write to the boot sector
or partition table of the hard disk drive. The system will halt and the following error message will appear in the
mean time. You can run anti-virus program to locate the problem.
Enabled
Disabled
Activate automatically when the system boots up causing a
warning message to appear when anything attempts to
access the boot sector or hard disk partition table
No warning message to appear when anything attempts to
access the boot sector or hard disk partition table. (Default
Value)
• Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory installed in the
system.
The value of the base memory is typically 512 K for systems with 512 K memory installed on the
motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU's memory address map.
Other Memory
This refers to the memory located in the 640 K to 1024 K address space. This is memory that can be
used for different applications.
DOS uses this area to load device drivers to keep as much base memory free for application
programs. Most use for this area is Shadow RAM
24
7ZX-1 Motherboard
BIOS Features Setup
AMIBIOS SETUP – BIOS FEATURES SETUP
( C ) 1999 American Megatrends, Inc. All Rights Reserved
1st Boot Device
Floppy
2nd Boot Device
CDROM
3rd Boot Device
IDE-0
S.M.A.R.T. for Hard Disks
Disabled
BootUp Num-Lock
On
Floppy Drive Seek
Enabled
Password Check
Setup
ESC : Quit
↑↓→ ←: Select Item
F1 : Help
PU/PD+/-/ : Modify
F5 :Old Values
(Shift)F2:Color
F6 : Load BIOS Defaults
F7 : Load SETUP Defaults
Figure 3: BIOS Features Setup
• 1st / 2nd / 3rd Boot Device
Floppy
ZIP A: / LS-120
CDROM
SCSI
NETWORK
IDE-0~IDE-3
Disabled
USB FDD
ATAPI ZIP C:
Boot Device by Floppy.
Boot Device by ZIP A: / LS-120.
Boot Device by CDROM.
Boot Device by SCSI.
Boot Device by NETWORK.
Boot Device by IDE-0~IDE-3.
Boot Device by Disabled.
Boot Device by USB FDD.
Boot Device by ATAPI ZIP C:.
• S.M.A.R.T. for Hard Disks
Enabled
Disabled
Enabled S.M.A.R.T. Hard for Disks.
Disabled S.M.A.R.T. Hard for Disks. (Default Value)
• Boot Up Num-Lock
On
Off
Keypad is number keys. (Default Value)
Keypad is arrow keys.
• Floppy Drive Seek
During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360 type is 40 tracks
while 720 , 1.2 and 1.44 are all 80 tracks.
Enabled
Disabled
BIOS searches for floppy disk drive to determine if it is 40
or 80 tracks. Note that BIOS can not tell from 720, 1.2 or
1.44 drive type as they are all 80 tracks. (Default Value)
BIOS will not search for the type of floppy disk drive by
track number. Note that there will not be any warning
message if the drive installed is 360.
• Password Check
Setup
Always
Set Password Check to Setup. (Default Value)
Set Password Check to Always.
25
BIOS Setup
Chipset Features Setup
AMIBIOS SETUP – CHIPSET FEATURES SETUP
( C ) 1999 American Megatrends, Inc. All Rights Reserved
*********DRAM Timing***
CAS# Drive
DRAM Frequency
Auto
RAS# Drive
SDRAM CAS# Latency
Auto
AGP Mode
AGP Comp. Driving
Manual AGP Comp. Driving
AGP Aperture Size
PCI Delay Transaction
USB Controller
USB Legacy Support
USB Port 64 / 60 Emulation
BIOS Flash Protection
DRAM Drive Strength
MD Bus Strength
CAS Bus Strength
Delay DRAM Read Latch
Memory Data Drive
SDRAM Command Drive
Memory Address Drive
4X
Auto
DB
64MB
Enabled
Enabled
Disabled
Disabled
Disabled
Auto
High
High
1.0ns
8 mA
24 mA
24 mA
12 mA
24 mA
ESC : Quit
↑↓→ ←: Select Item
F1 : Help
PU/PD+/-/ : Modify
F5 : Old Values
(Shift)F2:Color
F6 : Load BIOS Defaults
F7 : Load SETUP Defaults
Figure 4: Chipset Features Setup
• DRAM Frequency
100MHz
133MHz
Set DRAM Frequency to 100MHz.
Set DRAM Frequency to 133MHz.
• SDRAM CAS# Latency
2
3
Auto
For Fastest SDRAM DIMM module.
For Slower SDRAM DIMM module.
Detect SDRAM CAS# Latency by SPD. (Default Value)
• AGP Mode
4X
1X
2X
Set AGP Mode to 4X. (Default Value)
Set AGP Mode to 1X.
Set AGP Mode to 2X.
• AGP Comp. Driving
Auto
Manual
Set AGP Comp. Driving to Auto. (Default Value)
Set AGP Comp. Driving to Manual.
If AGP Comp. Driving is Manual.
Manual AGP Comp. Driving : 00~FF
• AGP Aperture Size
4MB
8MB
16MB
32MB
64MB
128MB
256MB
Set AGP Aperture Size to 4MB.
Set AGP Aperture Size to 8 MB.
Set AGP Aperture Size to 16 MB.
Set AGP Aperture Size to 32 MB.
Set AGP Aperture Size to 64 MB. (Default Value)
Set AGP Aperture Size to 128 MB.
Set AGP Aperture Size to 256 MB.
• PCI Delay Transaction
Enabled
Disabled
Enabled Delay Transaction. (Default Value)
Disabled Delay Transaction.
26
7ZX-1 Motherboard
• USB Controller
Enabled
Disabled
Enabled USB Controller. (Default Value)
Disabled USB Controller.
• USB Legacy Support
Keyboard/FD
D
KB/Mouse/F
DD
Disabled
Set USB Legacy Support Keyboard / Floppy.
Set USB Legacy Support Keyboard / Mouse /Floppy.
Disabled USB Legacy Support Function. (Default
Value)
• BIOS Flash Protection
Enabled
Disabled
BIOS Flash Write Protection.
Normal. (Default Value)
• DRAM Drive Strength
Auto
Manual
Set DRAM Drive Strength Auto. (Default Value)
Set DRAM Drive Strength Manual.
If DRAM Drive Strength is Manual, then you can adjust item below.
• MD Bus Strength
High
Low
Set MD Bus Strength High. (Default Value)
Set MD Bus Strength Low.
• CAS Bus Strength
High
Low
Set CAS Bus Strength High. (Default Value)
Set CAS Bus Strength Low.
• Delay DRAM Read Latch
1.0ns
1.5ns
0.5ns
No delay
Set DRAM Read Latch Delay 1.0ns. (Default Value)
Set DRAM Read Latch Delay 1.5ns.
Set DRAM Read Latch Delay 0.5ns.
Set DRAM Read Latch No delay.
• Memory Data Drive
6 mA
8 mA
Set Memory Data Drive 6 mA.
Set Memory Data Drive 8 mA. (Default Value)
• SDRAM Command Drive
16 mA
24 mA
Set SDRAM Command Drive 16 mA.
Set SDRAM Command Drive 24 mA. (Default Value)
• Memory Address Drive
16 mA
24 mA
Set Memory Address Drive 16 mA.
Set Memory Address Drive 24 mA. (Default Value)
• CAS# Drive
8 mA
12 mA
Set CAS# Drive 8 mA.
Set CAS# Drive 12 mA. (Default Value)
• RAS# Drive
16 mA
24 mA
Set RAS# Drive 16 mA.
Set RAS# Drive 24 mA. (Default Value)
27
BIOS Setup
Power Management Setup
AMIBIOS SETUP – POWER MANAGEMENT SETUP
( C ) 1999 American Megatrends, Inc. All Rights Reserved
ACPI Sleep Type
USB Dev Wakeup From S3-S5
Suspend Time Out(Minute)
Display Activity
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ13
IRQ14
IRQ15
Soft-Off by Power Button
System after AC Back
Modem Use IRQ
Resume On Ring/LAN
PME Event Wake Up
Resume On RTC Alarm
S1/POS
Disabled
Disabled
Ignore
Monitor
Monitor
Ignore
Monitor
Ignore
Ignore
Ignore
Ignore
RTC Alarm Date
RTC Alarm Hour
RTC Alarm Minute
RTC Alarm Second
Every Day
00
00
00
Monitor
Ignore
Memory
ESC : Quit
↑↓→ ←: Select Item
F1 : Help
PU/PD+/-/ : Modify
F5 :Old Values (Shift)F2:Color
F6 : Load BIOS Defaults
F7 : Load SETUP Defaults
Soft-Off
4
Enabled
Enabled
Disabled
Figure 5: Power Management Setup
• ACPI Sleep Type
S1/POS
S3/STR
Set ACPI sleep type to S1. (Default Value)
Set ACPI sleep type to S3.
• USB Dev Wakeup From S3-S5
Enabled
Disabled
Enabled USB Dev Wakeup From S3-S5.
Disabled USB Dev Wakeup From S3-S5. (Default Value)
• Suspend Time Out (Minute.)
Disabled
1
2
4
8
10
20
30
40
50
60
Disabled Suspend Time Out Function. (Default Value)
Enabled Suspend Time Out after 1min.
Enabled Suspend Time Out after 2min.
Enabled Suspend Time Out after 4min.
Enabled Suspend Time Out after 8min.
Enabled Suspend Time Out after 10min.
Enabled Suspend Time Out after 20min.
Enabled Suspend Time Out after 30min.
Enabled Suspend Time Out after 40min.
Enabled Suspend Time Out after 50min.
Enabled Suspend Time Out after 60min.
• Display Activity
Ignore
Monitor
Ignore Display Activity. (Default Value)
Monitor Display Activity.
• IRQ 3~IRQ15
Ignore
Monitor
Ignore IRQ3 ~IRQ15.
Monitor IRQ3~IRQ15.
• Soft-off by Power Button
Instant-off
Delay 4
sec
Soft switch ON/OFF for POWER ON/OFF. (Default
Value)
Soft switch on 4sec for power OFF.
28
7ZX-1 Motherboard
• System after AC Back Function
Memory
Soft-Off
Full-On
This function depends on computer status. . (Default
Value)
Set System Soft-Off Status
Set System Full-On Status.
• Modem USE IRQ
3, 4, (Default Value) 5, 7, N/A
• Resume On Ring / LAN
Disabled
Enabled
Disabled Resume On Ring / LAN.
Enabled Resume On Ring / LAN. (Default Value)
• PME Event Wake Up
Disabled
Enabled
Disabled PME Event Wake Up.
Enabled PME Event Wake Up. (Default Value)
• Resume On RTC Alarm
You can set “Resume On RTC Alarm” item to enabled and key in Data/time to power on
system.
Disabled
Enabled
Disable this function. (Default Value)
Enable alarm function to POWER ON system.
If the “Resume On RTC Alarm” is Enabled.
RTC Alarm Date :
RTC Alarm Hour:
RTC Alarm Minute :
RTC Alarm Second :
Every Day, 1~31
0~23
0~59
0~59
29
BIOS Setup
PnP/PCI Configurations
AMIBIOS SETUP – PNP / PCI CONFIGURATION
( C ) 1999 American Megatrends, Inc. All Rights Reserved
PnP Aware OS
Yes
Reset Configuration Data
No
VGA Boot from
AGP
Disabled
PCI AGP Palette Snoop
PnP
DMA Channel 0
DMA Channel 1
PnP
DMA Channel 3
PnP
PnP
DMA Channel 5
PnP
DMA Channel 6
PnP
DMA Channel 7
IRQ 3
PCI/PnP
IRQ 4
PCI/PnP
IRQ 5
PCI/PnP
IRQ 7
PCI/PnP
IRQ 9
PCI/PnP
IRQ 10
PCI/PnP
ESC: Quit
↑↓→ ←: Select Item
IRQ 11
PCI/PnP
F1 : Help
PU/PD+/-/ : Modify
IRQ 14
PCI/PnP
F5 :Old Values (Shift)F2:Color
IRQ 15
PCI/PnP
F6 : Load BIOS Defaults
F7 : Load SETUP Defaults
Figure 6: PnP/PCI Configuration
• PnP Aware OS
Yes
No
Enable PNP Aware OS function. (Default Value)
Disable PNP Aware OS function.
• Reset Configuration Data
No
Yes
Disable this function. (Default Value)
Clear PnP information in ESCD & update DMI data.
• VGA Boot From
AGP
PCI
Primary Graphics Adapter From AGP. (Default Value)
Primary Graphics Adapter From PCI.
• PCI/VGA Palette Snoop
Enabled
Disabled
For having Video Card on ISA Bus and VGA Card on PCI Bus.
For VGA Card only. (Default Value)
• DMA Channel ( 0,1,3,5,6,7 )
ISA/ EISA
PnP
The resource is used by Legacy ISA device.
The resource is used by PnP device.
• IRQ ( 3,4,5,7,9,10,11,14,15 )
ISA/ EISA
PCI / PnP
The resource is used by Legacy ISA device.
The resource is used by PCI/ PnP device.
30
7ZX-1 Motherboard
Load BIOS Defaults
AMIBIOS SIMPLE SETUP UTILITY-VERSION 1.23
( C ) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
HARDWARE MONITOR SETUP
CHIPSET FEATURES SETUP
SUPERVISOR PASSWORD
POWER MANAGEMENT SETUP
USER PASSWORD
PNP/PCI CONFIGURATION
IDE HDD AUTO DETECTION
Load BIOS Defaults
(Y/N)? N
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit ↑↓→← : Select Item (Shift) F2 : Change Color F5 : Old Values
F6 : Load BIOS Defaults
F7: Load Setup Defaults
F10: Save & Exit
Load BIOS Default except Standard CMOS Setup
Figure 7: Load BIOS Defaults
• Load BIOS Defaults
BIOS defaults contain the most appropriate values of the system parameters that allow minimum system
performance.
31
BIOS Setup
Load Setup Defaults
AMIBIOS SIMPLE SETUP UTILITY-VERSION 1.23
( C ) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
HARDWARE MONITOR SETUP
CHIPSET FEATURES SETUP
SUPERVISOR PASSWORD
POWER MANAGEMENT SETUP
USER PASSWORD
Load SETUP Defaults
(Y/N)?
PNP/PCI CONFIGURATION
IDE HDD
AUTONDETECTION
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit ↑↓→← : Select Item (Shift) F2 : Change Color F5 : Old Values
F6 : Load BIOS Defaults
F7: Load Setup Defaults F10: Save & Exit
Load Setup Default except Standard CMOS Setup
Figure 8: Load Setup Defaults
•
Load Setup Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically
detects.
Please use this setting for maximum system performance.
32
7ZX-1 Motherboard
Integrated Peripherals
AMIBIOS SETUP – INTEGRATED PERIPHERALS
( C ) 1999 American Megatrends, Inc. All Rights Reserved
OnBoard Serial Port A
Auto
Auto
OnBoard Serial Port B
Normal
Serial PortB Mode
Duplex Mode
N/A
Auto
OnBoard Parallel Port
Parallel Port Mode
ECP
Parallel Port DMA
Auto
Parallel Port IRQ
Auto
AC97 Audio
Auto
MC97 Modem
Auto
♦OnBoard Legacy Audio
♦Sound Blaster
♦SB I/O Base Address
♦SB IRQ Select
♦SB DMA Select
♦MPU-401
♦MPU-401 I/O Address
♦Game Port(200h-207h)
Enabled
Disabled
220h-22Fh
5
1
Disabled
330h-333h
Enabled
ESC: Quit
↑↓→ ←: Select Item
F1 : Help
PU/PD+/-/ : Modify
F5 :Old Values
(Shift)F2:Color
F6 : Load BIOS Defaults
F7 : Load SETUP Defaults
Figure 9: Integrated Peripherals
This items will be available when ”Serial PortB Mode” is set to IrDA or ASK IR.
♦These eight items will be shown when there are only AC’97 CODEC sound.
• On Board Serial Port A
Auto
BIOS will automatically setup the port A address.
(Default Value)
Enable on Board Serial port A and address to 3F8.
Enable on Board Serial port A and address to 2F8.
Enable on Board Serial port A and address to 3E8.
Enable on Board Serial port A and address to 2E8.
Disable on Board Serial port A.
3F8/COM1
2F8/COM2
3E8/COM3
2E8/COM4
Disabled
• On Board Serial Port B
Auto
BIOS will automatically setup the port B address.
(Default Value)
Enable on Board Serial port B and address to 3F8.
Enable on Board Serial port B and address to 2F8.
Enable on Board Serial port B and address to 3E8.
Enable on Board Serial port B and address to 2E8.
Disable on Board Serial port B.
3F8/COM1
2F8/COM2
3E8/COM3
2E8/COM4
Disabled
• Serial Port B Mode
Normal
IrDA
ASK IR
Normal operation. (Default Value)
Onboard I/O chip supports IRDA
Onboard I/O chip supports ASK IR.
• Duplex Mode
Half Duplex
N/A
Full Duplex
IR Function Duplex Half.
Disabled this function. (Default Value)
IR Function Duplex Full.
• On Board Parallel port
378
278
3BC
Auto
Disabled
Enable On Board LPT port and address to 378.
Enable On Board LPT port and address to 278.
Enable On Board LPT port and address to 3BC.
Set On Board LPT port to Auto. (Default Value)
Disable On Board LPT port.
33
BIOS Setup
• Parallel Port Mode
EPP
ECP
Normal
EPP+EC
P
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port. (Default
Value)
Normal Operation.
Using Parallel port as Enhanced Parallel Port & Extended
Capabilities Port.
• Parallel Port DMA
Auto
3
1
0
Set Auto to parallel port mode DMA Channel. (Default
Value)
Set Parallel Port DMA to 3.
Set Parallel Port DMA to 1.
Set Parallel Port DMA to 0.
• Parallel Port IRQ
7
Auto
5
Set Parallel Port IRQ to 7.
Set Auto to parallel Port IRQ DMA Channel. (Default
Value)
Set Parallel Port IRQ to 5.
• AC97 Audio
Auto
Disabled
Enabled On Board AC’97 Audio. (Default Value)
Disabled On Board AC’97 Audio.
• MC97 Modem
Auto
Disabled
Enabled On Board MC’97 Modem. (Default Value)
Disabled On Board MC’97 Modem.
• OnBoard Legacy Audio
Enabled
Disabled
Enabled OnBoard Legacy Audio. (Default Value)
Disabled OnBoard Legacy Audio.
• Sound Blaster
Enabled
Disabled
Enabled Sound Blaster.
Disabled Sound Blaster. (Default Value)
• SB I/O Base Address
220h22Fh
280h28Fh
260h26Fh
240h24Fh
Set SB I/O Base Address to 220h-22Fh. (Default Value)
Set SB I/O Base Address to 280h-28Fh.
Set SB I/O Base Address to 260h-26Fh.
Set SB I/O Base Address to 240h-24Fh.
• SB IRQ Select
IRQ 5 / 7 / 9 / 10. (Default Value: 5 )
• SB DMA Select
DMA 0 / 1 / 2/ 3. (Default Value: 1 )
34
7ZX-1 Motherboard
• MPU-401
Enabled
Disabled
Enabled MPU-401.
Disabled MPU-401. (Default Value)
Ps. When Force Feedback joystick is used, MPU-401 needs to be Enable.
• MPU-401 I/O Address
330h333h
300h303h
310h313h
320h323h
Set MPU-401 I/O Address to 330h-333h. (Default Value)
Set MPU-401 I/O Address to 300h-303h.
Set MPU-401 I/O Address to 310h-313h.
Set MPU-401 I/O Address to 320h-323h.
• Game Port (200h-207h)
Disabled
Enabled
Disabled Game Port (200h-207h).
Enabled Game Port (200h-207h). (Default Value)
35
BIOS Setup
Hardware Monitor
AMIBIOS SETUP – HARDWARE MONITOR SETUP
( C ) 1999 American Megatrends, Inc. All Rights Reserved
ACPI Shut Down Temp.
CPU Temperature
System Temperature
CPU Fan Speed
System Fan Speed
Vcore
Vdd
Vcc3
+5.000V
+12.000V
Disabled
32°C/89°F
32°C/89°F
7123 RPM
0 RPM
1.76 V
3.33 V
3. 27 V
4.97 V
12.18 V
ESC: Quit
↑↓→ ←: Select Item
F1 : Help
PU/PD+/-/ : Modify
F5 :Old Values (Shift)F2:Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Figure 10: Hardware Monitor
•
ACPI Shutdown Temp. (°°C / °F)
(This function will be effective only for the operating systems that support ACPI Function.)
Disabled
60°C / 140°F
70°C / 158°F
80°C / 176°F
90°C / 194°F
•
Disabled ACPI Shutdown function. (Default Value)
Monitor CPU Temp. at 60°C / 140°F, if Temp. > 60°C /
140°F system will automatically power off.
Monitor CPU Temp. at 70°C / 158°F, if Temp. > 70°C /
158°F system will automatically power off.
Monitor CPU Temp. at 80°C / 176°F, if Temp. > 80°C /
176°F system will automatically power off.
Monitor CPU Temp. at 90°C / 194°F, if Temp. > 90°C /
194°F system will automatically power off.
CPU Temperature (°°C / °F)
Detect CPU Temperature automatically.
•
System Temperature (°°C / °F)
Detect System Temperature automatically.
• CPU Fan Speed
Detect CPU Fan speed status automatically.
•
System Fan Speed
Detect System Fan speed status automatically.
• Current Voltage (V) Vcore / Vdd / Vcc3 / +5V / +12V
Detect system’s voltage status automatically.
36
7ZX-1 Motherboard
Set Supervisor / User Password
When you select this function, the following message will appear at the center of the screen to assist you in
creating a password.
AMIBIOS SIMPLE SETUP UTILITY-VERSION 1.23
( C ) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
HARDWARE MONITOR SETUP
CHIPSET FEATURES SETUP
SUPERVISOR PASSWORD
POWER MANAGEMENT SETUP
USER PASSWORD
PNP/PCI CONFIGURATIONEnter new supervisor
IDE HDDpassword:
AUTO DETECTION
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit ↑↓→← : Select Item (Shift) F2 : Change Color F5 : Old Values
F6 : Load BIOS Defaults
F7: Load Setup Defaults F10: Save & Exit
Chang /Set /Disabled Password
Figure 11: Password Setting
Type the password, up to six characters, and press <Enter>. You will be asked to confirm the password. Type the
password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message “PASSWORD
DISABLED” will appear to confirm the password being disabled. Once the password is disabled, the system will
boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords: a SUPERVISOR PASSWORD and a
USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the
Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the
User password is required to access only basic items.
If you select “System” at “Password Check” in BIOS Features Setup Menu, you will be prompted for the
password every time the system is rebooted or any time you try to enter Setup Menu.
If you select “Setup” at “Password Check” in BIOS Features Setup Menu, you will be prompted only when you
try to enter Setup.
37
BIOS Setup
IDE HDD AUTO Detection
AMIBIOS SETUP – STANDARD CMOS SETUP
( C ) 1999 American Megatrends, Inc. All Rights Reserved
Date (mm/dd/yyyy) : Tue Jan 25, 2000
Time (hh/mm/ss) : 10:36:24
TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
Pri Master : Not Installed
Pri Slave : Not Installed
Sec Master : Not Installed
Sec Slave : Not Installed
Floppy Drive A: 1.44 MB 3 ½
Floppy Drive B: Not Installed
Boot Sector Virus Protection : Disabled
Month: Jan – Dec
Day: 01 – 31
Year : 1990– 2099
Base Memory : 640 Kb
Other Memory: 384 Kb
Extended Memory: 31Mb
Total Memory: 32Mb
ESC : Exit
↑↓ : Select Item
PU/PD/+/– : Modify
(Shift)F2 : Color
Figure 12: IDE HDD Auto Detection
Type "Y" will accept the H.D.D. parameter reported by BIOS.
Type "N" will keep the old H.D.D. parameter setup. If the hard disk cylinder number is over 1024, then the user
can select LBA mode or LARGER mode for DOS partition larger than 528 MB.
38
7ZX-1 Motherboard
Save & Exit Setup
AMIBIOS SIMPLE SETUP UTILITY-VERSION 1.23
( C ) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
HARDWARE MONITOR SETUP
CHIPSET FEATURES SETUP
SUPERVISOR PASSWORD
POWER MANAGEMENT SETUP
USER PASSWORD
PNP/PCI CONFIGURATION
IDE HDD AUTO DETECTION
SAVE to CMOS and EXIT(Y/N)? Y
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit ↑↓→← : Select Item (Shift) F2 : Change Color F5 : Old Values
F6 : Load BIOS Defaults
F7: Load Setup Defaults F10: Save & Exit
Save Data to CMOS & Exit Setup
Figure 13: Save & Exit Setup
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
39
BIOS Setup
Exit Without Saving
AMIBIOS SIMPLE SETUP UTILITY-VERSION 1.23
( C ) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
HARDWARE MONITOR SETUP
CHIPSET FEATURES SETUP
SUPERVISOR PASSWORD
POWER MANAGEMENT SETUP
USER PASSWORD
PNP/PCI CONFIGURATION
IDE HDD AUTO DETECTION
LOAD BIOS DEFAULTS
Quit without saving (Y/N) ? N
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit ↑↓→← : Select Item (Shift) F2 : Change Color F5 : Old Values
F6 : Load BIOS Defaults
F7: Load Setup Defaults
F10: Save & Exit
Abandon all Datas & Exit Setup
Figure 14: Exit Without Saving
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
40
Appendix
Appendix: Acronyms
Acronyms
ACPI
POST
LAN
ECP
APM
DMA
MHz
ESCD
CPU
SMP
USB
OS
ECC
IDE
SCI
LBA
EMC
BIOS
SMI
IRQ
NIC
A.G.P.
S.E.C.C.
LED
EPP
CMOS
I/O
ESD
OEM
SRAM
VID
DMI
MIDI
IOAPIC
DIMM
DRAM
PAC
AMR
PCI
RIMM
DRM
ISA
MTH
CRIMM
Meaning
Advanced Configuration and Power Interface
Power-On Self Test
Local Area Network
Extended Capabilities Port
Advanced Power Management
Direct Memory Access
Megahertz
Extended System Configuration Data
Central Processing Unit
Symmetric Multi-Processing
Universal Serial Bus
Operating System
Error Checking and Correcting
Integrated Dual Channel Enhanced
Special Circumstance Instructions
Logical Block Addressing
Electromagnetic Compatibility
Basic Input / Output System
System Management Interrupt
Interrupt Request
Network Interface Card
Accelerated Graphics Port
Single Edge Contact Cartridge
Light Emitting Diode
Enhanced Parallel Port
Complementary Metal Oxide Semiconductor
Input / Output
Electrostatic Discharge
Original Equipment Manufacturer
Static Random Access Memory
Voltage ID
Desktop Management Interface
Musical Interface Digital Interface
Input Output Advanced Programmable Input Controller
Dual Inline Memory Module
Dynamic Random Access Memory
PCI A.G.P. Controller
Audio Modem Riser
Peripheral Component Interconnect
Rambus in-line Memory Module
Dual Retention Mechanism
Industry Standard Architecture
Memory Translator Hub
Continuity RIMM
41
Download PDF

advertising