American DJ Uni Pack DJ Equipment User Manual

®
4295 Charter Street
Los Angeles, CA. 90058
www.americandj.com
American DJ
User Instructions
American DJ
Revised 8/01
VERTI PRO II™
Set Up
Unpacking: Thank you for purchasing the VERTI PRO II™ by American DJ®. Every VERTI PRO II™ has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit have
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please, do not return this unit to your dealer without first
contacting customer support.
Introduction: The VERTI PRO II™ is an intelligent, DMX compatible
version of the standard Vertigo. This fixture can run in DMX mode, as
a stand alone sound active piece, or in a Master/Slave configuration.
The VERTI PRO II™ comes with several build in programs that will
trigger when operating in master/slave mode. This unit is best used in
multiples of four. This piece is best used with a fog or haze machine
to enhance the beam output. An optional VertiPro/C controller may be
purchased separately.
Warning! The 1/4” phone plug on the unit is for the optional VertiPro/C.
Do not attempt to connect an audio signal to this jack, this will damage
the PC board and void your manufactures warranty!
Customer Support: American DJ® provides a toll free customer support line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax:
(323) 582-2610
E-mail:
support@americandj.com
not expose this unit to rain or moisture.
Warning! To prevent or reduce the risk of electrical shock or fire, do
©American
DJ® www.americandj.com VERTI PRO II™ Instruction Manual Page 2
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ® customer support.
VERTI PRO II™
Contents
General Instructions
Introduction..........................................................................2
Features................................................................................3
Safety Precautions...................................................................4
Operation..............................................................................5
DMX Addressing.............................................................6
Set-Up................................................................................7
Controls & Functions..........................................................10
Lamp Replacement..............................................................11
Cleaning............................................................................12
Trouble Shooting............................................................12
DMX Traits............................................................................14
Warranty.....................................................................15
VERTI PRO II™
Features
Warranty Registration
Linkable.
Audio Sensitivity Knob.
Sound-Active.
DMX-512 Protocol Compatible.
Full Focusing.
Master/Slave Built-In Programs.
Optional VertiPro/C Blackout Controller.
VERTI PRO II™
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this
manual with the unit, for future reference.
•
•
•
•
•
•
•
VERTI PRO II™
©American
DJ® www.americandj.com VERTI PRO II™ Instruction Manual Page 3
The VERTI PRO II™ carries a one year (365 days) limited warranty.
We recommend you fill out the enclosed warranty card to validate your
purchase. All returned service items whether under warranty or not,
must be freight pre-paid and accompany a return authorization (R.A.)
number. If the unit is under warranty, you must provide a copy of your
proof of purchase invoice. Please contact American DJ® customer
support for a R.A. number.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
VERTI PRO II™
Safety Precautions
DJ® www.americandj.com VERTI PRO II™ Instruction Manual Page 4
This unit may blow a fuse if the maximum allotted load of 10 amps
(220v = 5 amps) is reached. If the fuse needs replacement, always
replace the fuse with same exact type that was remove. Use of a
different type fuse from that which is recommended may cause fire or
electric shock and will void the manufactures warranty
To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
Do not spill water or other liquids into or on to your unit
Be sure that the local power outlet match that of the required voltage
for your unit
Do not attempt to operate this unit if the power cord has been frayed
or broken
Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short
Disconnect from main power before making any type of connection
Do not remove the cover under any conditions. There are no user
serviceable parts inside
Never operate this unit when it’s cover is removed
Never plug this unit in to a dimmer pack
Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall
Do not attempt to operate this unit, if it becomes damaged
This unit is intended for indoor use only, use of this product outdoors
voids all warranties
During long periods of non-use, disconnect the unit’s main power
Always mount this unit in safe and stable matter
Power cords should be routed so they are not likely to be walked on,
pinched by items placed upon or against them.
Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 7 for cleaning details
Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
©American
Operation
VERTI PRO II™
Operation
DMX Indicate
1
2
4
8
16
32
64
128
256
M/S
MIC.
1 2 3 4 5 6 7 8 9 10
ON
MIC.
1 2 3 4 5 6 7 8 9 10
ON
MIC.
1 = Grand 2 = Data - 3 = Data +
DMX In
DMX Link
DMX Out
SENSITIVITY
DMX In
SENSITIVITY
DMX In
SENSITIVITY
MINI/C ONLY
1 = Grand 2 = Data - 3 = Data +
DMX Link
MINI/C ONLY
DMX Out
1 = Grand 2 = Data - 3 = Data +
DMX Link
DMX Out
MINI/C ONLY
Fuse
120 V / 10 A
240 V / 5 A
ON
Head 2-CH 2
Master
ON
Head 3-CH 3
ON
Head 1-CH 1
Master/Slave Chart
1 2 3 4 5 6 7 8 9 10
ON
Head 1-CH 1
Head 3-CH 3
ON
ON
1
2
4
8
16
32
64
128
256
M/S
VERTI PRO II™
Master
Master/Slave Chart
Head 2-CH 2
ON
ON
Fuse
120 V / 10 A
240 V / 5 A
DMX Indicate
dip-switch settings.
3. The optional VertiPro/C Blackout Controller may be used in this
operation mode to control a blackout function.
4. After the unit settings have been set and are plugged in, adjust
the sensitivity knob on the rear of the master unit to make them
react to sound.
Master/Slave Linking:
Power
Black = Live
White = Neutral
Green = Earth
Power
Black = Live
White = Neutral
Green = Earth
For a more dramatic effect, link several Color units together.
DMX Indicate
1
2
4
8
16
32
64
128
256
M/S
Head 1-CH 1
Head 3-CH 3
ON
ON
To next VERTI PRO II™ if applicable
Optional VertiPro/C or VertiPro/C blackout controller
Master
Master/Slave Chart
Head 2-CH 2
ON
ON
Fuse
120 V / 10 A
240 V / 5 A
©American
DJ® www.americandj.com VERTI PRO II™ Instruction Manual Page 6
Universal DMX Control: Operating through a DMX controller allows
the freedom to create unique programs tailored to one’s individual
needs.
1. The VERTI PRO II™ uses one DMX channel. This channel controls the rotation of the unit’s internal wheel. Please refer to page
14 for a detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the unit set-up procedures beginning on page 8 as well as the set-up specifications
that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create custom programs.
5. When using a DMX controller and setting up for DMX operation
follow the dip switch settings on page 13.
6. For help operating in DMX operation consult the manual included
with your DMX controller.
7. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture in you DMX chain.
Power
Black = Live
White = Neutral
Green = Earth
ON
Operating Modes: You can operate the VERTI PRO II™ in three
different modes:
• Stand-Alone mode (Usually for single unit operation) - The unit
will react to sound, chasing through the several built in programs.
You can also use the optional VertiPro/C remote control to blackout
the unit.
• Master/Slave mode - Allows you to daisy chain up to 4 fixtures
together for a synchronized light show. The fixtures will react to
sound chasing through several built in programs. You can also use
the optional VertiPro/C remote control to change programs and
blackout the units.
• DMX control mode - This function will allow you to control each
fixtures DMX traits with a standard DMX 512 controller such as
the American DJ® Show Designer™ or DMX Operator.™
NOTE: Stand-Alone and Master/Slave operation require a sound
source to operate properly. The units will blackout to conserve lamp
life when inactive for more than 60 seconds. A single sound source
will reactivate the units.
Stand Alone Mode:
1. To operate a single unit or several units as individuals in stand
alone mode, turn dip switch number 10 to the on position (see
page 13) and plug the unit(s) in. If you are running more than one
unit in stand alone mode do not link the units together.
2. Adjust the sensitivity knob on the bottom of the unit so the unit
will react to sound and cycle through the internal chases. Turning
the sensitivity knob in a clockwise direction will make the fixture
more sensitive to sound, turning the sensitivity knob in counterclockwise direction will make the fixture less sensitive to sound.
DJ® www.americandj.com VERTI PRO II™ Instruction Manual Page 5
Master-Slave Operation (Sound Active): In Master-Slave operation one unit will act as the controlling unit, the others will react to the
controlling units programs. Any unit can act as a master or a slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connectors on the rear of the unit. Remember the Male XLR connector is the input and the Female XLR is the
output. The first unit in (master) will use the female XLR connector
only. Refer to the set-up procedures beginning on page 8.
2. Follow the Master-Slave dip-switch chart on page 13 for proper
©American
VERTI PRO II™
MIC.
DMX Indicate
1 2 3 4 5 6 7 8 9 10
ON
1
2
4
8
16
32
64
128
256
M/S
DMX In
1 = Grand 2 = Data - 3 = Data +
DMX Link
DMX Out
DMX In
SENSITIVITY
DMX Indicate
1
2
4
8
16
32
64
128
256
M/S
Head 1-CH 1
DMX Indicate
ON
Head 3-CH 3
ON
Head 1-CH 1
1
2
4
8
16
32
64
128
256
M/S
Operation
Master
Master/Slave Chart
Head 2-CH 2
ON
ON
1 = Grand 2 = Data - 3 = Data +
DMX Link
MINI/C ONLY
DMX Out
1 = Grand 2 = Data - 3 = Data +
DMX Link
MINI/C ONLY
DMX Out
Fuse
120 V / 10 A
240 V / 5 A
Set Up
To next DMX unit or terminate.
Power
Black = Live
White = Neutral
Green = Earth
SENSITIVITY
Head 3-CH 3
ON
ON
1 2 3 4 5 6 7 8 9 10
ON
Master
Master/Slave Chart
Head 2-CH 2
ON
ON
Fuse
120 V / 10 A
240 V / 5 A
DMX In
MINI/C ONLY
Power
Black = Live
White = Neutral
Green = Earth
MIC.
SENSITIVITY
Head 3-CH 3
1 2 3 4 5 6 7 8 9 10
ON
Head 1-CH 1
ON
ON
MIC.
Master
Master/Slave Chart
Fuse
120 V / 10 A
240 V / 5 A
ON
Head 2-CH 2
ON
Typical DMX Linking:
Power
Black = Live
White = Neutral
Green = Earth
VERTI PRO II™
Power Supply: Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ® VERTI PRO II.™ Because line voltage may vary from venue to
venue, you should be sure your unit voltage matches the wall outlet
voltage before attempting to operate you fixture.
DMX-512: DMX is short for Digital Multiplex. This is a universal
protocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that
travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR
terminals located on all DMX fixtures (most controllers only have a
DATA “OUT” terminal).
©American
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 7
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX
fixtures try to use the shortest cable path possible. The order in which
fixtures are connected in a DMX line does not influence the DMX
addressing. For example; a fixture assigned a DMX address of 1 may
VERTI PRO II™
Set Up
be placed anywhere in a DMX line, at the beginning, at the end, or
anywhere in the middle. When a fixture is assigned a DMX address of
1, the DMX controller knows to send DATA assigned to address 1 to
that unit, no matter where it is located in the DMX chain.
ON
1
4
16
65 256
1 2 3 4 5 6 7 8 9 10
DMX CHANNEL
2
8 32 128 SP
Dip-switches in DMX mode: This unit uses dip switches to assign a
DMX address. Each dip switch represents a binary value.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
Set DMX address 201:
Dip-switches # 1 = 1
4=8
7 = 64
8 = 128
= 201
Each dip switch has a preset value. A specific DMX address is set by
combining the dip switches that sum your desired value. For example:
To achieve a DMX address of 21, combine dip switches 1, 3, and 5.
Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4,
and dip switch 5 has a value of 16, the combination of the create a
DMX value of 21.
Set DMX address 21:
Dip-switches # 1 = 1
3=4
5 = 16
= 21
Data Cable Requirements (For DMX and Master/Slave Opera-
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 8
tion): The VERTI PRO II™ can be controlled via DMX-512 protocol.
The DMX address is set using the dip-switches on the rear panel of the
VERTI PRO II™. Your unit excepts 3-pin XLR connector for data input
and data output (Figure 5). When using a DMX controller with 5-Pin
XLR output jacks or when linking from a DMX fixture with 5-Pin XLR
jack to the VERTI PRO II™, be sure to follow the pin conversion chart
on page 12. If you are making your own cables, be sure to use stan©American
VERTI PRO II™
Set Up
dard two conductor shielded cable (This cable may be purchased at
almost all pro sound and lighting stores). Your cables should be made
with a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and can not be split.
1
3 Hot
3
XLR Pin Configuration
Figure 6
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Figure 7
Pin 3 = Data True (positive)
DMX512 IN
3-PIN XLR
VERTI PRO II™
Ground/Shield
Conductor
Pin 2
Pin 1
3-Pin XLR Female (Out)
Pin 3
Pin 2
Pin 1
5-Pin XLR Male (In)
Set Up
Data Compliment (- signal)
Pin 3
3-Pin XLR to 5-Pin XLR Conversion
Data True (+ signal)
Not Used
Do Not Use
Do Not Use
MIC.
DMX Indicate
1 2 3 4 5 6 7 8 9 10
ON
Master
SENSITIVITY
ON
1
2
4
8
16
32
64
128
256
M/S
Head 3-CH 3
ON
Head 1-CH 1
Master/Slave Chart
DMX Out
MINI/C ONLY
Fuse
120 V / 10 A
240 V / 5 A
ON
Head 2-CH 2
ON
7
4
5
6
3
Controls and Functions
Not Used
2
1
VERTI PRO II™
©American
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 10
DMX Input Jack - This jack is used to accept an incoming DMX or
Master/Slave signal.
DMX Output Jack - This jack is used to send the incoming DMX or
Master/Slave signal to another DMX fixture.
Internal Mic - This mic triggers the unit in sound active mode.
Dip Switches - These switches are used to set the DMX and
Master/Slave address.
Mic Sensitivity - This adjust audio sensitivity of the internal
mic (3). Turning the sensitivity knob in the clockwise direction will
increase sound sensitivity. Turning the knob in a counter clockwise
direction will decrease sound sensitivity.
Remote Control Input - Do not attempt to connect an audio
signal to this jack, this will damage the unit! This jack is for use
with the optional VertiPro/C controller only.
Fuse Holder - This housing stores the protective fuse. Always
replace with the exact same type fuse, unless otherwise instructed
to do so by an authorized American DJ® service technician.
Power
Black = Live
White = Neutral
Green = Earth
DMX Link
2
1
1 Ground
XLR Female Socket
2 Cold
DMX +
COMMON
DMX -
1.
2.
3.
4.
5.
6.
7.
DMX In
1
2
Figure 8
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 9
1 = Grand 2 = Data - 3 = Data +
2
3
Notice: Be sure to follow figures 6 and 7 when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
2 Cold
XLR Male Socket
1 Ground
3 Hot
DMX512 OUT
3-PIN XLR
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number ZDMX/T) will decrease the possibilities of erratic
behavior.
©American
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
VERTI PRO II™
Fuse & Lamp Replacement
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ ® technician.
Replacing with anything other than the specified part can damage the
unit and will void the manufactures warranty.
Warning: If, after replacing the lamp or fuse either one continues
to blow, STOP using the unit. Contact customer support for further
instructions, you may have to return the unit for servicing. Continuing
to use the unit may cause serious damage.
Fuse Replacement: Disconnect the unit’s main power supply. Insert
a standard flat head screw driver in to the fuse holder housing. Turn
the screwdriver in counter-clockwise direction to remove the fuse
holder. Remove the fuse holder to expose the fuse. Remove the old
fuse and discard it. Replace the fuse with the same type. Insert the
fuse holder back into it’s housing and turn it in clockwise direction to
lock the holder in place.
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 11
This fixture is fitted with a halogen lamp which
is highly susceptible to damage if improperly handled. Never touch the lamp with your bare fingers
as the oil from your hands will shorten lamp life.
Also, never move the fixture until the lamp has
had ample time to cool. Remember, lamps are not
covered under warranty conditions.
Halogen Lamp Warning:
Lamp Replacement: Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power and
allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up top cover that is retained by a single thumb screw.
1. Be sure to follow the proper handling procedures that deal
with halogen lamps.
2. Remove the single thumb screw located in the front of the unit.
3. Flip-down the front cover to access the lamp socket assembly. The
cover is on hinges and will not fall off.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble.
©American
VERTI PRO II™
Trouble Shooting
Trouble Shooting:
Listed below are a few common problems that you may encounter,
with solutions.
No light output from the unit;
1. Be sure you have connected your unit into a standard 120V (or
220v depending on the models voltage requirements) wall outlet.
2. Be sure the external fuse has not blown. The fuse is located on the
rear panel of the unit.
3. Remove the lamp cover and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during shipping
be sure the lamp is push in to its socket all the way. Remember not
to touch the lamp with your bare fingers.
4. Be sure the fuse holder is completely and properly seated.
Cleaning
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may not
activate the unit.
2. Be sure the SENSITIVITY KNOB (3) is not set to the maximum
position.
VERTI PRO II™
Fixture Cleaning:
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 12
Due to fog residue, smoke, and dust cleaning the internal and external
optical lenses and mirror should be carried out periodically to optimize
light output. Cleaning frequency depends on the environment in which
the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club
use we recommend cleaning on a monthly basis. Periodic cleaning will
ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside
casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external lens with glass cleaner and a soft cloth every
20 days.
4. Clean the internal lens with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
©American
VERTI PRO II™
CW Slow
DMX Traits
255
CCW Fast
Master/Slave Chart
CCW Slow
Stop
128
127 129
The VERTI PRO II™ is a single DMX channel fixture
01
CW Fast
VERTI PRO II™
ON
Master - Head 1
1 2 3 4 5 6 7 8 9 10
Head 2
1 2 3 4 5 6 7 8 9 10
ON
Head 4
1 2 3 4 5 6 7 8 9 10
VERTI PRO II™
#3
X
X
X
X
O
O
O
O
X
X
X
X
O
O
O
O
X
X
X
X
O
O
O
O
X
X
X
X
O
O
O
O
#4
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
#5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
DMX Dip Switch Chart
X
X
X
X
3
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
X
X
X
O
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
X
X
O
X
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
X
X
O
O
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
X
O
X
X
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
X
O
X
O
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
X
O
O
X
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
X
O
O
O
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
O
X
X
X
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
O
X
X
O
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
O
X
O
X
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
O
X
O
O
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
O
O
X
X
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
O
O
X
O
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
O
O
O
X
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
O
O
O
O
D MX A dd ress
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Di p S w it ch P osi t i on
DMX Address Quick Reference Chart
This chart list the DMX dip switch setting for DMX address 1 through
511. Follow the instructions below to configure fixture dip switches with
your desired DMX address.
DIP SWITCHES
#2
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
#9
DMX DIP Switch Settings
#8
X = OFF
#7
O = ON
#6
#1
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
©American
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 14
The center numbers of this chart (1-511) represent a DMX address. The "X"'s
and "O"'s along the top and side of the chart represent dip switch poistion ("X"
for off and "O" for on). Find your desired DMX address from the center chart.
Identify the position for dip switches 1-5 from the chart on the left and dip
switches 6-9 from the chart on the top. Adjust the dip switches on your fixture to
match the position settings of the chart. For fixtures with 10 dip switches; dip
switch 10 is reserved for special functions.
DMX Address
This chart details the Master/Slave dip switch setting for Master/Slave
configuration for four units. Use these dip switch setting when you will
be using two or more fixtures in a Master/Slave configuration. The
“Master - Head 1” settings should only be used once.
ON
ON
Head 3
1 2 3 4 5 6 7 8 9 10
ON
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 13
Master - Head 1
1 2 3 4 5 6 7 8 9 10
VERTI PRO II™
Single Unit Operation Chart
This chart list the DMX dip switch setting for single head operation.
When using this fixture as a stand alone unit or when using multiple
VERTI PRO IIs as stand alone units, be sure all the fixtures match the
illustrated dip switch setting (10 to the on position - all others off).
©American
D ip S wi t c h P o s i t i o n
VERTI PRO II™ Warranty
1-YEAR LIMITED WARRANTY
A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be
free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)
from the date of purchase. This warranty shall be valid only if the product is purchased
within the United States of America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable evidence, at the
time service is sought.
B. For warranty service, send the product only to the American DJ® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement)
are within the terms of this warranty, American DJ® will pay return shipping charges only
to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package. No accessories should be shipped with the product. If any
accessories are shipped with the product, American DJ® shall have no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product
is modified in any manner which American DJ® concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the
American DJ® factory unless prior written authorization was issued to purchaser by American DJ®; if the product is damaged because not properly maintained as set forth in the
instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ® will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor
by reason of defects in material or workmanship. The sole responsibility of American DJ®
under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ®. All products covered by this warranty
were manufactured after January 1, 1990, and bear identifying marks to that effect.
E. American DJ® reserves the right to make changes in design and/or improvements upon
its products without any obligation to include these changes in any products theretofore
manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ® in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set
forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly
provided above; and under no circumstances shall American DJ® be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to American DJ® Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions
heretofore published.
DJ® - www.americandj.com - VERTI PRO II™ Instruction Manual Page 15
H. All lamps and fuses are not covered under this warranty.
©American
MODEL: VERTI PRO II™
SPECIFICATIONS:
VOLTAGE:
LAMP:
DIMENSIONS:
WEIGHT:
FUSE:
WORKING POSITION:
COOLING:
DUTY CYCLE:
GOBOS:
COLORS:
120V~60Hz / 220V~50Hz
ZB-64514 120v/300w or
ZB-64516 220v/300w
10.5” (H) X 11” (W) X 10.5 “ (D)
(with yoke extended)
10 LBS / 7.5 KGS.
120V = 10 AMP GMA
220V = 5 AMP GMA
ANY SAFE POSITION
FAN COOLED
30 MIN. ON, 10 MIN. OFF
NONE
MULTIPLE
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©American DJ Supply
American DJ® World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-2650 Fax: 323-582-2610
Web: www.americandj.com E-mail: info@americandj.com