Installation manual | American Dryer Corp. /T75 Clothes Dryer User Manual

T20 / T30 / T50 / T75
Installation/Operator Manual
WARNING: For your safety the information
in this manual must be followed to
minimize the risk of fire or explosion and
to prevent property damage, personal
injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch;
do not use any phone in your
building.
● Clear the room, building or area of
all occupants.
● Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
● If you cannot reach your gas
supplier, call the fire department.
●
●
— Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter
tout dommage matériel, toute blessure ou
la mort.
—Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.
—QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ:
Ne pas tenter d’allumer d’appareils.
Ne touchez à aucun interrupteur. Ne
pas vous servir des téléphones se
trouvant dans le bâtiment.
● Évacuez la pièce, le bâtiment ou la
zone.
● Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.
● Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.
●
●
—L’installation et l’entretien doivent être
assurés par un installateur ou un
service d’entretien qualifié ou par le
fournisseur de gaz.
JLA Limited
Meadowcroft Lane, Halifax Road
Ripponden
West Yorkshire, England
HX6 4AJ
Telephone: 01422 822282 / Fax: 01422 824390
Part No. 113429-9
Retain This Manual in a Safe Place for Future Reference
This product embodies advanced concepts in engineering, design, and safety. If this product is properly
maintained, it will provide many years of safe, efficient, and trouble free operation.
Only qualified technicians should service this equipment.
OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation
manual included with the dryer.
The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location.
FOR YOUR SAFETY
POUR VOTRE SÉCURITÉ
Do not store or use gasoline
or other flammable vapors
and liquids in the vicinity of
this or any other appliance.
Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.
We have tried to make this manual as complete as possible and hope you will find it useful. The manufacturer
reserves the right to make changes from time to time, without notice or obligation, in prices, specifications,
colors, and material, and to change or discontinue models. The illustrations included in this manual may not
depict your particular dryer exactly.
IMPORTANT
For your convenience, log the following information:
DATE OF PURCHASE __________________________________________________ MODEL NO. ________________________
RESELLER’S NAME ______________________________________________________________________________________
Serial Number(s) ________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
Replacement parts can be obtained from your distributor or JLA. When ordering replacement parts, you can
FAX your order to JLA at 01422 824390 or telephone your order directly to the JLA Parts Department at
01422 822282. Please specify the dryer model number and serial number in addition to the description and
part number, so that your order is processed accurately and promptly.
“IMPORTANT NOTE TO PURCHASER”
Information must be obtained from your local gas supplier on the
instructions to be followed if the user smells gas. These
instructions must be posted in a prominent location near the dryer.
2
JLA Limited
113429 - 9
IMPORTANT
You must disconnect and lockout the electric
supply and the gas supply or the steam supply
before any covers or guards are removed from
the machine to allow access for cleaning,
adjusting, installation, or testing of any equipment
per OSHA standards.
Please observe all safety precautions displayed
on the equipment and/or specified in the
installation manual included with the dryer.
Before installation, check that the local distribution
conditions, nature of gas and pressure, and
adjustment of the appliances are compatible.
CAUTION
Dryer(s) should never be left unattended while in
operation.
When discarding or storing your old clothes
dryer, remove the door.
Lorsque vous entreposez ou mettez votre
sécheuse au rebut, enlevez-en la porte.
“Caution: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper operation.”
«Attention: Au moment de l’entretien des
commandes, étiquetez tous les fils avant de les
débrancher. Des erreurs de câblage peuvent
entraîner un fonctionnement inadéquat et
dangereux.»
WARNING
Children should not be allowed to play on or near
the dryer(s). Children should be supervised if near
dryer(s) in operation.
Under no circumstances should the dryer door
switch(es), lint door/drawer switch(es), or heat
safety circuit(s) ever be disabled.
The dryer must never be operated with any of the
back guards, outer tops, or service panels
removed. Personal injury or fire could result.
The dryer must never be operated without the lint
filter/screen in place, even if an external lint
collection system is used.
FOR YOUR SAFETY
Do not dry mop heads in the dryer. Do not use
dryer in the presence of dry cleaning fumes.
The dryers must not be installed or stored in an
area where it will be exposed to water and/or
weather.
The wiring diagram for the dryer is located behind
the control panel.
113429 - 9
Table of Contents ________
Safety Precautions ................................ 4
T20 Specifications ................................ 6
T30 Specifications ................................ 8
T50 Specifications .............................. 10
T75 Specifications .............................. 12
Installation Procedures ...................... 14
Location Requirements .........................................
Unpacking/Setting Up ...........................................
Dryer Enclosure Requirements .............................
Fresh Air Supply Requirements ............................
Exhaust Requirements .........................................
Electrical Information ............................................
Gas Information ....................................................
Converting from One Family of Gas to Another .....
Gas Pressure Testing ...........................................
Steam Information .................................................
Water Information .................................................
Preparation for Operation/Start-Up ........................
Preoperational Test ...............................................
Preoperational Instructions ...................................
Shutdown Instructions ..........................................
14
14
14
15
15
17
21
24
26
26
27
28
28
29
29
Service/Parts Information .................. 29
Service .................................................................. 29
Parts ..................................................................... 29
Warranty Information ......................... 29
Returning Warranty Cards ..................................... 29
Warranty ............................................................... 30
Routine Maintenance .......................... 30
Data Label Information ....................... 31
List of Acronyms _______________________
HVAC
Heating, Ventilating, and Air-Conditioning
in WC
Inches of Water Column
L.C.D.
Liquid Crystal Display
L.E.D.
Light Emitting Diode
L.P.
Liquid Propane
OSHA
Occupational Safety and Health Administration
UL
Underwriters Laboratory
Telephone 01422 822282
3
Safety Precautions ____________________
Warning
!
For your safety, the information in this manual
must be followed to minimize the risk of fire or
explosion and to prevent property damage, personal injury,
or loss of life.
The dryer must never be operated with any of the back
guards, outer tops, or service panels removed. Personal
injury or fire could result.
Failure to properly install, maintain, and/or operate dryer
according to this manual and operator’s manuals included
with dryer may result in conditions which can cause serious
injury, death and/or property damage.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Purchaser and user should consult the local gas supplier for
proper instructions to be followed in the event the user smells
gas. The instructions should be posted in a prominent
location.
What To Do If You Smell Gas:
A program should be established for the inspection and
cleaning of lint in the burner area, exhaust ductwork, and
area around the back of the dryer. The frequency of inspection
and cleaning can best be determined from experience at
each location.
Do not operate steam dryers with more than 150 psi (10.34
bar) steam pressure. Excessive steam pressure can damage
the steam coil and/or harm personnel.
Replace leaking flexible hoses or other steam fixtures
immediately. Do not operate the dryer with leaking flexible
hoses. Personal injury may result.
Warning
!
The collection of lint in the burner area and
exhaust ductwork can create a potential fire
hazard.
For personal safety, the dryer must be electrically grounded
in accordance with local and/or country codes. In the absence
of these codes use the National Electrical Code ANSI/NFPA
NO. 70-LATEST EDITION or in Canada, the Canadian
Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST
EDITION.
Note
• Do not try to light any appliance.
!
• Do not touch any electrical switch.
Failure to electrically ground the dryer properly will
void the warranty.
• Do not use any phone in your building.
Warning
• Clear the room, building, or area of all occupants.
!
Personal injury or fire could result should the dryer
door switch, lint door/drawer, or heat safety circuit
ever be disabled.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by a qualified
installer, service agency, or gas supplier.
Remove articles from the dryer as soon as the drying cycle
has been completed.
Warning
Dryers must be exhausted to the outdoors.
Although the manufacturer produces a very versatile dryer,
there are some articles that, due to fabric composition or
cleaning method, should not be dried in it.
Warning
!
Dry only water washed fabrics. Do not dry articles
spotted or washed in dry cleaning solvents,
combustible detergents, or “all purpose” cleaner.
Explosion could result.
Do not dry rags or articles coated or contaminated with
gasoline, kerosene, oil, paint, or wax. Explosion could
result.
Items that have been spotted or soaked with vegetable or
cooking oil constitute a fire hazard and should not be
placed in a tumble dryer.
Do not dry mop heads. Contamination by wax or
flammable solvents will create a fire hazard.
Do not use heat for drying articles that contain plastic,
foam, sponge rubber, or similarly textured rubber
materials. Drying in a heated tumbler may damage
plastics or rubber and also may be a fire hazard.
!
Articles left in the dryer after the drying and cooling
cycles have been completed can create a fire
hazard.
For safety, proper operation, and optimum performance, the
dryer must not be operated with a load less than 66% of its
rated capacity.
Warning
!
You must disconnect and lockout the electric
supply and the gas supply or the steam supply
before any covers or guards are removed from the
machine to allow access for cleaning, adjusting,
installation, or testing of any equipment per OSHA
standards.
Important
!
The dryer must be installed in a location/
environment, which the ambient temperature
remains between 40° F (4.44° C) and 130° F (54.44° C).
The operation of this appliance may affect the operation of
other types of gas appliances, which take their air for safe
combustion from the same room. If in doubt, consult the
appliance manufacturer(s).
Use this dryer only for its intended purpose, drying fabrics.
4
JLA Limited
113429 - 9
The “cool down” cycle of tumble dryers should be used to
reduce the temperature of the items. They should not be
removed from the tumble dryer or piled or stacked while hot.
Fabric softeners or similar products should not be used in a
tumbler dryer to eliminate the effects of static electricity unless
this practice is specifically recommended by the manufacturer
of the fabric softener or product.
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
Warning
!
To reduce the risk of personal injury, install
lockable doors to prevent public access to the rear
of the dryers.
Exhaust duct outlet should be checked periodically for
blockages, and if any found, removed.
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
Important
!
NOTES ______________________________________________________
A means of restraint must be used to prevent
straining of the gas supply when the appliance is
_____________________________________________________________
moved.
_____________________________________________________________
An external means of power removal (disconnect device)
must be provided by the installer.
_____________________________________________________________
CE ONLY
Important
_____________________________________________________________
_____________________________________________________________
!
This appliance must only be installed and
operated in the country of destination indicated on
the dryer’s data plate. If the appliance is to be installed and
operated in a country other than the one indicated on the
data plate, a data plate amendment must be obtained from
JLA Limited.
Warning
!
This appliance must only operate with the gas type
indicated on the dryer’s data plate. If the appliance
is converted (gas type is changed), a data plate
amendment must be obtained from JLA Limited.
This appliance may cause spillage of products of
combustion from an open-flue appliance fitted in the same
room, and that such an appliance shall be tested for
clearance of products with the appliance in operation and
all windows and doors closed.
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
NOTES ______________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
113429 - 9
Telephone 01422 822282
5
T20 Specifications __________________________________________________________________
MAXIMUM CAPACITY (DRY WEIGHT)
TUMBLER DIAMETER
TUMBLER DEPTH
TUMBLER VOLUME
TUMBLER/DRIVE MOTOR
BLOWER/FAN MOTOR
DOOR OPENING (DIAMETER)
DOOR SILL HEIGHT
WATER CONNECTION
Steam
Electric
Gas
DRYERS PER 20’/40’ CONTAINER
DRYERS PER 48’/53’ TRUCK
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
HEAT INPUT
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
INLET PIPE CONNECTION
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60
AIRFLOW
50
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
OVEN SIZE
kcal/hr
kW
Btu/hr
3,488
4.1
13,843
4,300
5.0
17,065
4,644
5.4
18,430
4,816
5.6
19,112
5,246
6.1
20,819
5,590
6.5
22,184
5,848
6.8
23,208
6,364
7.4
25,255
6,450
7.5
25,597
6,966
8.1
27,644
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60
AIRFLOW
50
Hz
Hz
9.07 kg
20 lb
65.41 cm
25-3/4”
60.96 cm
24”
212.38 L
7-1/2 cu ft
0.19 kW
1/4 hp
0.25 kW
1/3 hp
49.21 cm
19-3/8”
33.02 cm
13”
3/4”-11.5 NH (North America)
3/4” B.S.P.T. (Outside North Ameri ca)
42 / 84
96 / 108
120-240V
1ø
2w 50/60 Hz
111.13 kg
245 lb
120.20 kg
265 lb
6.51 cmm
230 cfm
5.40 cmm
191 cfm
10,080 kcal/hr
40,000 Btu/hr
10.16 cm
4”
N / A
N / A
3/8” M.N.P.T.
3/8” M.B.S.P.T. (CE and Australi a Only)
200-416V
1,3ø 2,3,4w
50/60 Hz
111.13 kg
245 lb
120.20 kg
265 lb
6.51 cmm
230 cfm
5.40 cmm
191 cfm
10.16 cm
4”
N / A
N / A
Hz
Hz
STEAM CONSUMPTION
OPERATING STEAM PRESSURE
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
BOILER HORSEPOWER (NORMAL LOAD)
SUPPLY CONNECTION
RETURN CONNECTION
Shaded areas are stated in metric equivalents
!
6
120-240V
1ø
2w 50/60 Hz
114.76 kg
253 lb
123.83 kg
273 lb
6.51 cmm
230 cfm
5.40 cmm
191 cfm
20.41 kg/hr
45 lb/hr
10.34 bar
150 psi max
10.16 cm
4”
N / A
N / A
1.2 Bhp
1/2” F.N.P.T.
1/2” F.N.P.T.
5/1/06
Note
The manufacturer reserves the right to make changes in specifications at any time without notice or obligation.
JLA Limited
113429 - 9
T20 Specifications __________________________________________________________________
113429 - 9
Telephone 01422 822282
7
T30 Specifications __________________________________________________________________
MAXIMUM CAPACITY (DRY WEIGHT)
TUMBLER DIAMETER
TUMBLER DEPTH
TUMBLER VOLUME
TUMBLER/DRIVE MOTOR
BLOWER/FAN MOTOR
DOOR OPENING (DIAMETER)
DOOR SILL HEIGHT
WATER CONNECTION
Steam
Electric
Gas
DRYERS PER 20’/40’ CONTAINER
DRYERS PER 48’/53’ TRUCK
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
HEAT INPUT
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
INLET PIPE CONNECTION
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
OVEN SIZE
kcal/hr
kW
Btu/hr
6,794
7.9
26,962
7,138
8.3
28,327
7,740
9.0
30,716
9,719
11.3
38,566
10,665
12.4
42,320
10,751
12.5
42,661
11,611
13.5
46,074
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
STEAM CONSUMPTION
OPERATING STEAM PRESSURE
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
BOILER HORSEPOWER (NORMAL LOAD)
SUPPLY CONNECTION
RETURN CONNECTION
13.61 kg
30 lb
76.20 cm
30”
68.58 cm
27”
312.62 L
11.04 cu ft
0.19 kW
1/4 hp
0.37 kW
1/2 hp
49.21 cm
19-3/8”
37.78 cm
14-7/8”
3/4”-11.5 NH (North Ameri ca)
3/4” B.S.P.T. (Outside North Ameri ca)
12 / 28
34 / 38
120-240V
1ø 2w
50/60 Hz
129.27 kg
285 lb
140.61 kg
310 lb
10.19 cmm
360 cfm
8.49 cmm
300 cfm
13,860 kcal/hr
55,000 Btu/hr
15.24 cm
6”
N / A
N / A
1/2” M.N.P.T.
3/8” M.B.S.P.T. (CE and Australi a Only)
200-416V
1,3ø 2,3,4w
50/60 Hz
129.27 kg
285 lb
140.61 kg
310 lb
10.19 cmm
360 cfm
8.49 cmm
300 cfm
15.24 cm
6”
N / A
N / A
Shaded areas are stated in metric equivalents
!
8
120-240V
1ø 2w
50/60 Hz
138.35 kg
305 lb
149.69 kg
330 lb
10.19 cmm
360 cfm
8.49 cmm
300 cfm
28.58 kg/hr
63 lb/hr
10.34 bar
150 psi max
15.24 cm
6”
N / A
N / A
1.75 Bhp
1/2” F.N.P.T.
1/2” M.N.P.T.
9/30/05
Note
The manufacturer reserves the right to make changes in specifications at any time without notice or obligation.
JLA Limited
113429 - 9
T30 Specifications __________________________________________________________________
113429 - 9
Telephone 01422 822282
9
T50 Specifications __________________________________________________________________
MAXIMUM CAPACITY (DRY WEIGHT)
TUMBLER DIAMETER
TUMBLER DEPTH
TUMBLER VOLUME
TUMBLER/DRIVE MOTOR
BLOWER/FAN MOTOR
DOOR OPENING (DIAMETER)
DOOR SILL HEIGHT
WATER CONNECTION
Steam
Electric
Gas
DRYERS PER 20’/40’ CONTAINER
DRYERS PER 48’/53’ TRUCK
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
AIRFLOW
60 Hz
50 Hz
HEAT INPUT
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
INLET PIPE CONNECTION
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
AIRFLOW
60 Hz
50 Hz
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
OVEN SIZE
kcal/hr
kW
Btu/hr
11,559
13.4
45,869
12,634
14.7
50,136
12,737
14.8
50,545
13,761
16.0
54,606
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
AIRFLOW
60 Hz
50 Hz
STEAM CONSUMPTION
OPERATING STEAM PRESSURE
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
BOILER HORSEPOWER (NORMAL LOAD)
SUPPLY CONNECTION
RETURN CONNECTION
22.68 kg
50 lb
93.98 cm
37”
65.41 cm
25-3/4”
453.64 L
16.02 cu ft
0.56 kW
3/4 hp
0.37 kW
1/2 hp
69.53 cm
27-3/8”
40.64 cm
16”
3/4”-11.5 NH (North America)
3/4” B.S.P.T. (Outside North America)
10 / 22
28 / 30
120-240V 1ø 2w 50/60 Hz
247.21 kg
545 lb
256.28 kg
565 lb
14.87 cmm
525 cfm
12.37 cmm
437 cfm
22,680 kcal/hr
90,000 Btu/hr
20.32 cm
8”
N/A
N/A
1/2” M.N.P.T.
1/2” F.B.S.P.T. (CE and Australia Only)
120-600V 1,3ø 2,3,4w 50/60 Hz
247.21 kg
545 lb
256.28 kg
565 lb
14.87 cmm
525 cfm
12.37 cmm
437 cfm
20.32 cm
8”
N/A
N/A
Shaded areas are stated in metric equivalents
!
10
120-240V 1ø 2w 50/60 Hz
247.21 kg
545 lb
256.28 kg
565 lb
14.87 cmm
525 cfm
12.37 cmm
437 cfm
57.83 kg/hr
127.5 lb/hr
10.34 bar
150 psi max
20.32 cm
8”
N/A
N/A
3.75 Bhp
3/4” F.N.P.T.
3/4” M.N.P.T.
4/30/07
Note
The manufacturer reserves the right to make changes in specifications at any time without notice or obligation.
JLA Limited
113429 - 9
T50 Specifications __________________________________________________________________
113429 - 9
Telephone 01422 822282
11
T75 Specifications __________________________________________________________________
MAXIMUM CAPACITY (DRY WEIGHT)
TUMBLER DIAMETER
TUMBLER DEPTH
TUMBLER VOLUME
TUMBLER/DRIVE MOTOR
BLOWER/FAN MOTOR
DOOR OPENING (DIAMETER)
DOOR SILL HEIGHT
WATER CONNECTION
Steam
Electric
Gas
DRYERS PER 20’/40’ CONTAINER
DRYERS PER 48’/53’ TRUCK
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
HEAT INPUT
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
INLET PIPE CONNECTION
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
OVEN SIZE
kcal/hr
kW
Btu/hr
15,902
18.5
63,105
17,000
20.3
69,000
18,921
22.0
75,084
VOLTAGE AVAILABLE
APPROXIMATE NET WEIGHT
APPROXIMATE SHIPPING WEIGHT
60 Hz
AIRFLOW
50 Hz
STEAM CONSUMPTION
OPERATING STEAM PRESSURE
EXHAUST CONNECTION (DIAMETER)
COMPRESSED AIR CONNECTION
COMPRESSED AIR VOLUME
BOILER HORSEPOWER (NORMAL LOAD)
SUPPLY CONNECTION
RETURN CONNECTION
34.02 kg
75 lb
93.98 cm
37”
90.17 cm
35-1/2”
625.52 L
22.09 cu ft
0.56 kW
3/4 hp
0.37 kW
1/2 hp
69.53 cm
27-3/8”
40.64 cm
16”
3/4”-11.5 NH (North America)
3/4” B.S.P.T. (Outside North America)
9 / 20
25 / 27
120-240V
1ø 2w
50/60 Hz
272.16 kg
600 lb
281.23 kg
620 lb
15.86 cmm
560 cfm
13.19 cmm
466 cfm
27,720 kcal/hr
110,000 Btu/hr
20.32 cm
8”
N / A
N / A
1/2” M.N.P.T.
1/2” F.B.S.P.T. (CE and Australi a Only)
200-416V
1,3ø
2,3,4w
50/60 Hz
272.16 kg
600 lb
281.23 kg
620 lb
15.86 cmm
560 cfm
13.19 cmm
466 cfm
20.32 cm
8”
N / A
N / A
Shaded areas are stated in metric equivalents
!
12
120-240V
1ø 2w
50/60 Hz
272.16 kg
600 lb
281.23 kg
620 lb
15.86 cmm
560 cfm
13.19 cmm
466 cfm
61.69 kg/hr
136 lb/hr
10.34 bar
150 psi max
20.32 cm
8”
N / A
N / A
4 Bhp
3/4” F.N.P.T.
3/4” M.N.P.T.
4/30/07
Note
The manufacturer reserves the right to make changes in specifications at any time without notice or obligation.
JLA Limited
113429 - 9
T75 Specifications __________________________________________________________________
113429 - 9
Telephone 01422 822282
13
Installation Procedures _______________
Unpacking/Setting Up _________________
Installation should be performed by competent professional
in accordance with local, state, and country codes. In the
absence of these codes, the installation must conform to
applicable American National Standards: ANSI Z223.1-LATEST
EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70LATEST EDITION (National Electrical Code) or in Canada,
the installation must conform to applicable Canadian
Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/
CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General
Installation and Gas Plumbing) or Canadian Electrical Codes
Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION (for
Electrical Connections).
Remove protective shipping material (i.e., plastic wrap and
optional shipping box) from the dryer.
Location Requirements _______________
Before installing the dryer, be sure the location conforms to
local, state, and country codes. In the absence of such codes
or ordinances the location must conform with the National
Fuel Gas Code ANSI.Z223.1 LATEST EDITION, or in Canada,
the installation must conform to applicable Canadian
Standards: CAN/CGA-B149.1-M91 (Natural Gas) or
CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for
General Installation and Gas Plumbing).
The dryer must be installed on a sound level floor capable of
supporting its weight. Carpeting must be removed from the
floor area that the dryer is to rest on.
The dryer must not be installed or stored in an area where it
will be exposed to water and/or weather.
Dryers installed in residential garages must be elevated
18-inches (45.72 cm) above the floor.
Important
!
Dryer must be transported and handled in an
upright position at all times.
The dryer can be moved to its final location while still attached
to the skid or with the skid removed. To remove the skid from
the T20, simply lift the unit off of the skid; for the T30, T50, or
T75, locate and remove the 2 bolts securing the base of the
dryer to the wooden skid. One is located at the center rear
and the other is at the center front.
With the skid removed, use caution and assure all four
leveling legs are fully retracted if the dryer is to be slid into its
final position.
Leveling Dryer
The dryer is equipped with 4 leveling legs, 1 at each corner of
the base. For optimum performance the dryer should be
level front-to-back and side-to-side.
Dryer Enclosure Requirements _______
Commercial Type II
(T20, T30, T50, T75)
Bulkheads and partitions should be made of noncombustible
material.
Note
Provisions for adequate air supply must be provided as noted
in this manual (refer to Fresh Air Supply Requirements
section).
!
Allowances must be made for opening the control
door.
Clearance provisions must be made from combustible
construction as noted in this manual (refer to Dryer Enclosure
Requirements section).
Provisions must be made for adequate clearances for
servicing and for operation as noted in this manual (refer to
Dryer Enclosure Requirements section).
The dryer must be installed with a proper exhaust duct
connection to the outside as noted in this manual (refer to
Exhaust Requirements section).
The dryer must be located in an area where correct exhaust
venting can be achieved as noted in this manual (refer to
Exhaust Requirements section).
Important
!
The dryer should be located where a minimum
amount of exhaust ducting will be necessary.
A
The requirement to allow the door to open completely for
the T20 is 30-inches (76.2 cm), T30 is 33-inches (83.8
cm), and T50 and T75 is 40-inches (101.6 cm).
B
A minimum overhead clearance of 6-inches (15.24 cm)
is required.
C
Dryer should be positioned a minimum of 12-inches
(30.48 cm) away from the nearest obstruction. 24-inches
(60.96 cm) is recommended for ease of installation,
maintenance, and service.
D
1/16” (1.5875 mm) minimum is required.
E
Flooring should be level or below dryer cabinet for ease
of removing panels during maintenance.
F
Dryers may be positioned sidewall to sidewall, however
a 1/16” (1.5875 mm) minimum allowance must be made
for the opening and closing of the control door, along
with the removal of panels during maintenance.
The dryer must be installed with adequate clearance for air
openings into the combustion chamber.
Caution
!
This dryer produces combustible lint and must be
exhausted to the outdoors. Every 6 months,
inspect the exhaust ducting and remove any lint buildup.
Important
!
The dryer must be installed in a location/
environment, which the ambient temperature
remains between 40° F (4.44° C) and 130° F (54.44° C).
14
JLA Limited
113429 - 9
Domestic Type I (T20, T30, T50 Only)
A = 6-inches (15.24 cm)
B = 24-inches (60.96 cm)
A = 10-inches (25.4 cm)
B = 11-inches (27.94 cm)
EXAMPLE: For a bank of 4 T30 dryers, 2 unrestricted openings
measuring 10-inches by 11-inches (25.4 cm by 27.94 cm)
are acceptable.
EXAMPLE: For T50, 2 unrestricted openings measuring
6-inches by 24-inches (15.24 cm by 60.96 cm) are acceptable.
If a closet door is installed: unobstructed air openings are
required. The air openings shall be located 3-inches
(7.62 cm) from the lower opening (above floor level) and upper
opening (below ceiling). The total free area of the air openings
in the door shall not be less than 130 inch2 (838.708 cm2) for
T20; 179 inch2 (1154.836 cm2) for T30; and 293 inch2 (1890.319
cm2) for T50. Louvered doors with equivalent air openings
are acceptable.
No other fuel-burning appliance shall be installed in the same
closet as the dryer.
Fresh Air Supply Requirements _______
When the dryer is operating, it draws in room air, heats it,
passes this air through the tumbler, and exhausts it out of the
building. Therefore, the room air must be continually
replenished from the outdoors. If the make-up air is
inadequate, drying time and drying efficiency will be adversely
affected. Ignition problems and sail switch “fluttering”
problems may result, as well as premature motor failure from
overheating. The dryer must be installed with provisions for
adequate combustion and make-up air supply.
Air supply (make-up air) must be given careful consideration
to ensure proper performance of each dryer. As a general
rule, an unrestricted air entrance from the outdoors of 110
inch2 (710 cm2) is required for each T75, 90 inch2 (580 cm2)
for each T50, 55 inch2 (354 cm2) for each T30, and 40 inch2
(258 cm2) for each T20. (Based on 1 inch2 [6.5 cm2] per 1,000
Btu [252 kcal].)
It is not necessary to have a separate make-up air opening
for each dryer. Common make-up air openings are
acceptable. However, they must be set up in such a manner
that the make-up air is distributed equally to all the dryers.
To compensate for the use of registers or louvers used over
the openings, this area must be increased by approximately
33%. Make-up air openings should not be located in an area
directly near where exhaust vents exit the building.
Allowances must be made for remote or constricting
passageways or where dryers are located at high altitudes
or predominantly low pressure areas.
Note
!
Component failure due to dry cleaning solvent
fumes will void the warranty.
113429 - 9
Important
!
Make-up air must be free of dry cleaning solvent
fumes. Make-up air that is contaminated by dry
cleaning solvent fumes will result in irreparable damage to
the motors and other dryer components.
Exhaust Requirements________________
Exhaust ductwork should be designed and installed by a
qualified professional. Improperly sized ductwork will create
excessive back pressure, which results in slow drying,
increased use of energy, and shutdown of the burner by the
airflow (sail) switch, burner hi-limits, or lint chamber hi-limit
protector thermostat. The dryer must be installed with a proper
exhaust duct connection to the outside.
The dryer shall not be exhausted into any gas vent, chimney,
wall, ceiling or concealed space of a building.
Caution
!
This dryer produces combustible lint and must be
exhausted to the outdoors.
Improperly sized or installed exhaust ductwork can create
a potential fire hazard.
The ductwork should be laid out in such a way that the
ductwork travels as directly as possible to the outdoors with
as few turns as possible. There should be a minimum
6-inch (15.24 cm) clearance between the back guard and the
first bend in the ductwork for ease of servicing. Single or
independent dryer venting is recommended. It is suggested
that the use of 90° turns be avoided; use 30° and/or 45°
bends instead. The radius of the elbows should preferably
be 1-1/2 times the diameter of the duct. All ductwork should
be smooth inside with no projections from sheet metal
screws or other obstructions, which will collect lint. When
adding ducts, overlap the duct being connected. All ductwork
joints must be taped to prevent moisture and lint from
escaping into the building. Back draft dampers must be
installed in all commonly ducted systems. Inspection doors
should be installed at strategic points in the exhaust ductwork
for periodic inspection and cleaning of lint from the ductwork.
Important
!
It is recommended that exhaust or booster fans
not be used in the exhaust ductwork system.
Telephone 01422 822282
15
Important
Vertical Venting
!
Exhaust back pressure measured by a
manometer/magnehelic in the exhaust duct must
be no less than 0 and must not exceed 0.6 in WC (1.48
mb).
Note
!
When the exhaust ductwork passes through a wall,
ceiling, or roof made of combustible materials, the
opening must be 2-inches (5.08 cm) larger than the duct
(all the way around). The duct must be centered within this
opening.
When vertical dryer venting is used, the length of the ductwork
from the dryer to the outside exhaust outlet, must not exceed
12 feet (3.66 meters). The minimum diameter of this ductwork
must be at least 4-inches (10.16 cm) for T20, 6-inches (15.24
cm) for T30, and 8-inches (20.32 cm) for T50 and T75.
Including tumbler/dryer elbow connections or elbows used
for outside protection from the weather, no more than 3
elbows should be used in the exhaust duct run. If more than
3 elbows are used, the cross-sectional area of the ductwork
must be increased.
As per the National Fuel Gas Code, “Exhaust ducts for type
2 clothes dryers shall be constructed of sheet metal or
other noncombustible material. Such ducts shall be
equivalent in strength and corrosion resistance to ducts
made of galvanized sheet steel not less than 26 gauge
(0.0195-inches [0.50 mm]) thick.”
The ductwork for this appliance must be suitable for the
appliance category in accordance with national installation
regulations of the country of destination.
Outside Ductwork Protection
To protect the outside end of the horizontal ductwork from the
weather, a 90° elbow bent downward should be installed
where the exhaust exits the building. If the ductwork travels
vertically up through the roof, it should be protected from the
weather by using a 180° turn to point the opening downward.
In either case, allow at least twice the diameter of the duct
between the duct opening and the nearest obstruction (refer
to the diagram).
A = 20 feet (6.10 meters)
B = T20 – 4-inches (10.16 cm)
T30 – 6-inches (15.24 cm)
T50, T75 – 8-inches (20.32 cm)
C = 12 feet (3.66 meters)
D = T20 – 4-inches (10.16 cm)
T30 – 6-inches (15.24 cm)
T50, T75 – 8-inches (20.32 cm)
Important
!
Do not use screens, louvers, or caps on the outside
opening of the exhaust ductwork.
Single Dryer Venting
Important
!
For extended ductwork runs, the cross-sectional
area of the ductwork can only be increased to an
extent. When the ductwork approaches the maximum
limits as noted in this manual, a professional HVAC firm
should be consulted for proper venting information.
Horizontal Venting
When horizontal dryer venting is used, the length of the
ductwork from the dryer to the outside exhaust outlet, must
not exceed 20 feet (6.10 meters). The minimum diameter of
this ductwork must be at least 4-inches (10.16 cm) for T20,
6-inches (15.24 cm) for T30, and 8-inches (20.32 cm) for T50
and T75. Including tumbler/dryer elbow connections or
elbows used for outside protection from the weather, no more
than 1 elbow should be used in the exhaust duct run. If more
than 1 elbow is used, the cross-sectional area of the ductwork
must be increased.
NOTE 1 Opening from combustible materials must be 2-inches (5.08 cm)
larger than the duct (all the way around). The duct must be centered
within this opening.
NOTE 2 Distance should be 2 times the diameter of the duct to the nearest
obstruction.
Multiple Dryer (Common) Venting
Important
!
For extended ductwork runs, the cross-sectional
area of the ductwork can only be increased to an
extent. When the ductwork approaches the maximum
limits as noted in this manual, a professional HVAC firm
should be consulted for proper venting information.
If it is not feasible to provide separate exhaust ducts for each
dryer, ducts from individual dryers may be channeled into a
“common main duct.” The individual ducts should enter the
bottom or side of the main duct at an angle not more than 45º
in the direction of airflow. The main duct should be tapered,
with the diameter increasing before each individual duct is
added.
16
JLA Limited
113429 - 9
Important
!
Electrical Information_________________
No more than 4 dryers should be connected to 1
main common duct.
The illustration below shows the minimum cross-sectional
area for multiple dryer round or square venting. These figures
must be increased if the main duct run from the last dryer to
where it exhausts to the outdoors is longer than 12 feet (3.656
meters) or has more than 1 elbow in it.
A = T20 4-inch (10.16 cm)
T30 6-inch (15.24 cm)
T50 8-inch (20.32 cm)
T75 8-inch (20.32 cm)
B = 12 feet (3.656 meters)
Electrical Requirements
All electrical connections must be made by a properly licensed
and competent electrician. This is to ensure that the electrical
installation is adequate and conforms to local, state, and
national regulations or codes of the country of origin. In the
absence of such codes, all electrical connections, materials,
and workmanship must conform to the applicable
requirements of the National Electrical Code ANSI/NFPA NO.
70-LATEST EDITION or in Canada, the Canadian Electrical
Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.
Important
!
Failure to comply with these codes or ordinances,
and/or the requirements stipulated in this manual
can result in personal injury or component failure.
Note
!
Component failure due to improper installation will
void the warranty.
Each dryer should be connected to an independently protected
branch circuit. The dryer must be connected with copper
wire only. Do not use aluminum wire, which could cause a
fire hazard. The copper conductor wire/cable must be of proper
ampacity and insulation in accordance with electric codes
for making all service connections.
NOTE 1 Opening from combustible materials must be 2-inches (5.08 cm)
larger than the duct (all the way around). The duct must be centered
within this opening.
NOTE 2 Distance should be 2 times the diameter of the duct to the nearest
obstruction.
T20
Multiple Dryer Venting with 4-Inch (10.16 cm) Diameter
230 cfm (6.51 cmm) Exhaust Connections at Common Duct
NUMBER OF DRYERS
SQ IN
SQ CM
IN
MINIMUM ROUND
DUCT DIAMETER
CM
MINIMUM CROSSSECTIONAL AREA
4
80
516.1
10
25.4
3
80
516.1
10
25.4
2
54
348.4
8
20.32
1
30
193.55
6
15.24
T30
Multiple Dryer Venting with 6-Inch (15.24 cm) Diameter
360 cfm (10.19 cmm) Exhaust Connections at Common Duct
NUMBER OF DRYERS
SQ IN
MINIMUM CROSSSECTIONAL AREA SQ CM
IN
MINIMUM ROUND
DUCT DIAMETER
CM
4
80
516.1
10
25.4
3
80
516.1
10
25.4
2
54
348.4
8
20.32
1
30
193.55
6
15.24
T50
Multiple Dryer Venting with 8-Inch (20.32 cm) Diameter
525 cfm (14.87 cmm) Exhaust Connections at Common Duct
NUMBER OF DRYERS
SQ IN
MINIMUM CROSSSECTIONAL AREA SQ CM
IN
MINIMUM ROUND
DUCT DIAMETER
CM
4
120
774.2
12
30.48
3
120
774.2
12
30.48
2
80
516.1
10
25.4
1
54
348.4
8
20.32
Note
!
The use of aluminum wire will void the warranty.
An individual ground circuit must be provided to
each dryer, do not daisy chain.
Component failure due to improper voltage application will
void the warranty.
The manufacturer reserves the right to make changes in
specifications at any time without notice or obligation.
!
Important
A separate protected circuit must be provided to
each dryer.
The dryer must be connected to the electric supply shown
on the data label. In the case of 208 VAC or 240 VAC, the
supply voltage must match the electric service
specifications of the data label exactly.
Important
!
The wire size must be properly sized to handle the
related current.
Warning
!
208 VAC and 240 VAC are not the same. Any
damage done to dryer components due to
improper voltage connections will automatically void the
warranty.
T75
Multiple Dryer Venting with 8-Inch (20.32 cm) Diameter
560 cfm (15.86 cmm) Exhaust Connections at Common Duct
NUMBER OF DRYERS
SQ IN
SQ CM
IN
MINIMUM ROUND
DUCT DIAMETER
CM
MINIMUM CROSSSECTIONAL AREA
113429 - 9
4
120
774.2
12
30.48
3
120
774.2
12
30.48
2
80
516.1
10
25.4
1
54
348.4
8
20.32
Telephone 01422 822282
17
Warning (Gas Models Only)
Steam Models Only
!
Dryers built for use with a voltage between 200
and 240 must verify the input voltage during
installation. If the nominal voltage is outside of the
medium tolerances shown on the diagram below, adjust
the autotransformer, located
near the burner assembly.
LINE VOLTAGE
To adjust the
TERM
autotransformer wiring,
50 Hz
60 Hz
place the red wire on the
260
283
HIGH
appropriate tap (HIGH, MED,
226
249
LOW) of the
239
260
autotransformer. For
MED
208
230
additional wiring details,
refer to the electrical
217
236
LOW
diagram located on the
189
208
inside of the control panel.
ELECTRICAL SERVICE SPECIFICATIONS
IMPORTANT:
NOTES:
B.
C.
SERVICE
VOLTAGE
ELECTRICAL SERVICE SPECIFICATIONS
IMPORTANT:
208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, specify
exact voltage.
NOTES:
When fuses are used they must be dual element, time delay, current limiting,
class RK1 or RK5 ONLY. Calculate/determine correct fuse value, by applying
either local and/or National Electrical Codes to listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) motor curve type ONLY.
For others, calculate/verify correct breaker size according to appliance amp
draw rating and type of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.
C.
SERVICE
VOLTAGE
PHASE
120
200
208
220
230
240
1ø
1ø
1ø
1ø
1ø
1ø
WIRE
SERVICE
APPROX.
AMP DRAW
CIRCUIT
BREAKER
60 Hz
50 Hz
8.9
7.7
7.6
—
—
7.2
—
7.8
—
7.4
7.3
7.0
15
15
15
15
15
15
1ø
1ø
1ø
1ø
1ø
1ø
2
2
2
2
2
2
120
200
208
220
230
240
1ø
1ø
1ø
1ø
1ø
1ø
2
2
2
2
2
2
2
2
2
2
2
2
60 Hz
50 Hz
120
208
220
230
240
1ø
1ø
1ø
1ø
1ø
2
2
2
2
2
9.3
6.2
5.6
—
5.1
—
6.0
5.5
5.4
—
15
15
15
15
15
120
200
208
220
230
240
1ø
1ø
1ø
1ø
1ø
1ø
2
2
2
2
2
2
14.4
8.2
8.2
7.8
—
7.6
—
—
—
8.4
8.5
—
20
20
20
20
20
20
120
200
208
220
230
240
1ø
1ø
1ø
1ø
1ø
1ø
2
2
2
2
2
2
14.4
8.2
8.2
7.8
—
7.6
—
—
—
8.4
8.5
—
20
20
20
20
20
20
10.3
8.7
8.4
8.1
—
7.7
—
8.8
—
8.1
7.4
7.0
15
15
15
15
15
15
15.6
10.5
10.5
10.0
—
9.7
—
—
—
10.7
10.8
—
20
20
20
20
20
20
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
T75
1ø
1ø
1ø
1ø
1ø
1ø
CIRCUIT
BREAKER
NOTES ______________________________________________________
T50
120
200
208
220
230
240
APPROX.
AMP DRAW
7/15/08
T30
120
200
208
220
230
240
WIRE
SERVICE
T75
T20
2
2
2
2
2
2
PHASE
T50
Gas Models Only
B.
When fuses are used they must be dual element, time delay, current limiting,
class RK1 or RK5 ONLY. Calculate/determine correct fuse value, by applying
either local and/or National Electrical Codes to listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) motor curve type ONLY.
For others, calculate/verify correct breaker size according to appliance amp
draw rating and type of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.
T30
Electrical Service Specifications
A.
A.
208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, specify
exact voltage.
_____________________________________________________________
15.6
10.5
10.5
10.0
—
9.7
—
—
—
10.7
10.8
—
20
20
20
20
20
20
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
7/15/08
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
18
JLA Limited
113429 - 9
Electric Models Only
Grounding
All electrically heated dryers must be connected to the electric
service shown on the dryer’s data label. The connecting
wires must be properly sized to handle the rated current.
A ground (earth) connection must be provided and installed
in accordance with local, state, and national regulations or
codes of the country of origin. In the absence of these codes,
grounding must conform to applicable requirements of the
National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION,
or in Canada, the installation must conform to applicable
Canada Standards: Canadian Electrical Codes Parts 1 & 2
CSA C22.1-1990 or LATEST EDITION. The ground connection
may be to a proven earth ground at the location service panel.
ELECTRICAL SERVICE SPECIFICATIONS
IMPORTANT:
208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, specify exact voltage.
NOTES:
When fuses are used they must be dual element, time delay, current limiting, class RK1 or RK5
ONLY. Calculate/determine correct fuse value, by applying either local and/or National Electrical
Codes to listed appliance amp draw data.
Circuit breakers are thermal-magnetic (industrial) type ONLY. For others, calculate/verify correct
breaker size according to appliance amp draw rating and type of breaker used.
Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.
A.
B.
C.
SERVICE
VOLTAGE
PHASE
WIRE
SERVICE
200
208
208
220
230
230
240
240
208
240
380
400
416
1ø
1ø
1ø
1ø
1ø
1ø
1ø
1ø
3ø
3ø
3ø
3ø
3ø
2
2
2
2
2
2
2
2
3
3
4
4
4
200
208
208
230
230
240
240
208
220
230
240
380
400
416
1ø
1ø
1ø
1ø
1ø
1ø
1ø
3ø
3ø
3ø
3ø
3ø
3ø
3ø
2
2
2
2
2
2
2
3
3
3
3
4
4
4
200
208
220
230
240
200
208
220
230
240
380
400
416
1ø
1ø
1ø
1ø
1ø
3ø
3ø
3ø
3ø
3ø
3ø
3ø
3ø
2
2
2
2
2
3
3
3
3
3
4
4
4
120
480
1ø
3ø
OVEN
kW
APPROX.
AMP DRAW
CIRCUIT
BREAKER
60 Hz
50 Hz
32.7
24.2
34.0
35.6
—
—
27.1
38.4
22.7
22.6
—
—
—
32.7
—
—
—
26.4
36.8
—
38.4
—
—
15.0
15.5
15.8
45
35
45
45
35
50
35
50
30
30
20
20
20
68.4
43.8
70.7
—
—
42.7
61.5
43.3
35.3
—
37.7
22.8
—
—
67.7
—
—
41.3
59.1
—
—
—
—
36.5
—
22.6
23.1
23.7
90
60
90
60
80
60
80
60
50
50
50
40
40
40
82.1
85.1
68.8
—
74.2
—
52.6
43.0
—
46.0
28.0
—
—
—
—
69.4
72.3
75.1
51.0
—
43.6
45.3
—
28.6
29.8
30.7
110
110
90
100
100
70
70
60
60
60
40
40
40
—
—
15
25
—
—
15
25
—
—
15
20
6.5
15.4
—
—
15
20
109.8
113.9
91.7
—
99.2
69.2
56.2
—
60.4
35.6
—
—
—
—
—
92.3
96.3
—
—
56.8
59.1
—
—
36.2
37.8
39.1
150
150
125
125
125
90
80
80
80
45
50
50
50
T20
5.6
4.1
6.1
6.8
5.0
7.4
5.4
8.1
6.5
7.5
6.8
7.5
8.1
T30
12.5
7.9
13.5
8.3
12.4
9.0
13.5
13.5
11.3
12.4
13.5
11.3
12.4
13.5
T50
14.8
16.0
13.4
14.7
16.0
14.8
16.0
13.4
14.7
16.0
13.4
14.8
16.0
T50 Dual Voltage 480 / 120
2
3
0.0
16.0
13.2
19.2
T50 Dual Voltage 480 / 240
240
480
1ø
3ø
2
3
120
600
1ø
3ø
240
600
1ø
3ø
2
3
200
208
220
230
240
208
220
230
240
380
380
400
416
1ø
1ø
1ø
1ø
1ø
3ø
3ø
3ø
3ø
3ø
3ø
3ø
3ø
2
2
2
2
2
3
3
3
3
4
4
4
4
0.0
16.0
6.5
19.2
T50 Dual Voltage 600 / 120
2
3
0.0
16.0
13.2
15.4
T50 Dual Voltage 600 / 240
0.0
16.0
T75
20.3
22.0
18.5
20.3
22.0
22.0
18.5
20.3
22.0
18.5
18.5
20.3
22.0
For added personal safety, when possible, it is suggested
that a separate ground wire (size per local codes) be
connected from the ground connection of the dryer to a
grounded cold water pipe. Do not ground to a gas pipe or hot
water pipe. The grounded cold water pipe must have
metal-to-metal connection all the way to the electrical ground.
If there are any nonmetallic interruptions, such as, a meter,
pump, plastic, rubber, or other insulating connectors, they
must be jumped out with a wire (size per local codes) and
securely clamped to bare metal at both ends.
Important
!
For personal safety and proper operation, the
dryer must be grounded.
Provisions are made for ground connection in each dryer at
the electrical service connection area.
Warning
!
Electrical Grounding Instructions – This dryer is
equipped with a 3-prong (grounding) plug for your
protection against shock hazard and should be plugged
directly into a properly grounded 3-prong receptacle. Do
not cut or remove the grounding prong from this plug.
Electrical Connections
A wiring diagram is located behind the control panel for
connection data.
If local codes permit, power to the dryer can be made by the
use of a flexible UL listed power cord/pigtail (wire size must
conform to rating of dryer), or the dryer can be hard wired
directly to the service breaker panel. In both cases, a strain
relief must be installed where the wiring enters the dryer.
For CE Models Only
The means for disconnection from the supply must be
incorporated into wiring having a minimum contact separation
of 3.0mm in all poles.
Single-Phase (1ø)
Wiring Connections/Hookup
The electrical input connections are made into the rear service
box located at the upper right area of the dryer. The ground
connection is made to the copper lug, also provided in this
box. To gain access, the service box cover must be removed.
7/15/08
113429 - 9
Telephone 01422 822282
19
Caution
Gas and Steam Models Only
!
120-240V Application with Neutral
The dryer must be grounded. A ground lug has
been provided for this purpose.
Input connection wiring must be sized properly to handle the
dryer’s current draw. This information is printed on the dryer’s
data label.
Electric Models Only
Single-Phase (1ø) Wiring Connections/Hookup
Two Element Configuration
200-240V Application without Neutral
Three Element Configuration
Caution
!
The dryer must be grounded. A ground lug has
been provided for this purpose.
Input connection wiring must be sized properly to handle the
dryer’s current draw. This information is printed on the dryer’s
data label.
Important
!
A strain relief must be used where the input wiring
enters the oven assembly.
Electrically Heated Models Only
3-Phase (3ø) Wiring Connections/Hookup
The electrical input connections are made at the rear service
box located at the right upper section of the dryer. The ground
connection is made to a copper lug also provided in this
area. To gain access, remove rear service cover.
The only electrical input connections to the dryer are the
3-phase (3ø) power leads (L1, L2, L3, and sometimes neutral)
and ground. Single-phase (1ø) power for the control circuit
and for any single-phase (1ø) motors (if present) is done
internally to the dryer by the factory at the oven contactor. No
single-phase (1ø) input connection is required on a 3-phase
(3ø) dryer.
The neutral will only be used on 4-wire service. This is typical
for 380-416V, 50 Hz.
20
JLA Limited
113429 - 9
Gas Information________________________
It is your responsibility to have all plumbing connections,
materials, and workmanship conform to local and state
regulations or codes of the country of destination. In the
absence of such codes, all plumbing connections, materials,
and workmanship must conform to the applicable local
requirements. In the USA this is the National Fuel Gas Code
ANSI Z223.1-LATEST EDITION, or in Canada, the Canadian
Installation Codes CAN/CGA-B149.1-M91 (Natural Gas) or
CAN/CGAB149.2-M91 (L.P. Gas) or LATEST EDITION.
It is important that gas pressure regulators meet applicable
pressure requirements, and that gas meters be rated for the
total amount of all the appliance Btu being supplied.
Important
!
Failure to comply with these codes or ordinances,
and/or the requirements stipulated in this manual,
can result in personal injury and improper operation of the
dryer.
For ease of service, the individual gas supply line of each
dryer must have its own manual shutoff valve.
The dryer and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess
of 1/2 psig (3.5 kPa) for non-CE dryers or 50 mb for CE
dryers.
Failure to isolate or disconnect the dryer from supply as
noted can cause irreparable damage to the gas valve,
voiding the warranty.
Note
!
If connection to this appliance is made with a
flexible hose, it must be suitable for the appliance
category in accordance with national installation
regulations of the country of destination, and if in doubt the
installer must contact the supplier. The manufacturer of
this appliance does not recommend the use of flexible gas
supply line/hose. An external gas supply shutoff must be
provided.
CE Dryers
There is an N.P.T. to B.S.P.T. adaptor included with each dryer,
which must be installed to the gas inlet. The adaptor is
shipped in the tumbler.
Important
!
Pipe joint compounds that resist the action of
natural, propane, and butane gases must be used.
NOTES ______________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
!
The dryer must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure test of the gas supply
system at test pressures equal to or less than 1/2 psig (3.5
kPa) for non-CE dryers or 50 mb for CE dryers.
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
Warning
!
Important
Fire or explosion could result due to failure of
isolating or disconnecting the gas supply as noted.
_____________________________________________________________
_____________________________________________________________
Note
!
Undersized gas piping will result in ignition
problems, slow drying, increased use of energy,
and can create a safety hazard.
_____________________________________________________________
The dryer must be connected to the type of heat/gas indicated
on the data label and pressure must be confirmed. If this
information does not agree with the type of gas available, do
not operate the dryer. Contact the reseller who sold the dryer
or contact the manufacturer.
_____________________________________________________________
The input ratings shown on the data label are for elevations
up to 2,000 feet (610 meters), unless elevation requirements
of over 2,000 feet (610 meters) were specified at the time the
dryer order was placed with the factory. The adjustment or
conversion of dryers in the field for elevations over 2,000 feet
(610 meters) is made by changing each burner orifice. If this
conversion is necessary, contact the reseller who sold the
dryer or contact the manufacturer.
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
113429 - 9
Telephone 01422 822282
21
Heat Input/Gas Consumption/Orifice (Injector) Data (For Non CE [European] Models Only)
Gas Specifications for Non-CE Approved Dryers**
T20
T30
T50
T75
Nominal
Heating Value
Supply
Pressure
Gross
Heat Input
Burner
Pressure
B tu /ft 3
in wc
Btu/hr
kW
DMS
mm
Orifice
(Injector)
Quantity
Natural
1,000
7.0-13.0
40,000
11.72
30
3.264
1
3.0
*Liquid Propane
2,500
11.0
40,000
11.72
49
1.854
1
10.0
Natural
1,000
7.0-13.0
55,000
16.12
20
4.089
1
3.0
*Liquid Propane
2,500
11.0
55,000
16.12
44
2.184
1
10.0
Natural
1,000
7.0-13.0
90,000
26.38
29
3.454
2
3.0
*Liquid Propane
2,500
11.0
90,000
26.38
47
2.994
2
10.0
Natural
1,000
7.0-13.0
110,000
32.24
22
3.988
2
3.0
*Liquid Propane
2,500
11.0
110,000
32.24
44
2.184
2
10.0
Gas
Type
Model
Orifice Size
in wc
Shaded areas are stated in metric equivalents
* Gas valve’s internal regulator disabled.
** Consult factory for elevations over 2,000 feet (610 meters) for correct orifice size.
Heat Input/Gas Consumption/Orifice (Injector) Data (For CE [European] Models Only)
Gas Specifications for CE Approved Dryers**
Model
Gas
Type
T30
T50
T75
Supply
Pressure
Gross
Heat Input
Fuel
Consumption
Orifice Size
Orifice
(Injector)
Quantity
Burner
Pressure
B tu /ft 3
mb
Btu/hr
kW
DMS
mm
1,000
15-30
40,000
11.72
1.133 M3 /H
30
3.264
1
6.7
Natural (I2 L )
830
20-35
40,000
11.72
1.365 M3 /H
30
3.264
1
9.2
Natural (I2 E L L )
830
15-30
40,000
11.72
1.365 M3 /H
30
3.264
1
9.2
1,000
20
40,000
11.72
1.133 M3 /H
38
2.578
1
—
830
25
40,000
11.72
1.365 M3 /H
38
2.578
1
—
*Butane (I3+ )
3,175
28-30
40,000
11.72
0.845 kg/H
52
1.613
1
—
*Propane (I3 + )
2,500
37
40,000
11.72
0.845 kg/H
52
1.613
1
—
Butane (I3 B /P )
3,175
28-30/50
40,000
11.72
0.845 kg/H
49
1.854
1
18.0
Propane (I3 P )
2,500
28-30/50
40,000
11.72
0.845 kg/H
49
1.854
1
23.0
Natural (I2 H /I2E )
1,000
15-30
55,000
16.12
1.557 M3 /H
22
3.988
1
6.9
Natural (I2 L )
830
20-35
55,000
16.12
1.876 M3 /H
22
3.988
1
9.5
Natural (I2 E L L )
830
15-30
55,000
16.12
1.876 M3 /H
22
3.988
1
9.5
1,000
20
55,000
16.12
1.557 M3 /H
31
3.048
1
—
830
25
55,000
16.12
1.876 M3 /H
31
3.048
1
—
*Butane (I3+ )
3,175
28-30
55,000
16.12
1.162 kg/H
48
1.930
1
—
*Propane (I3 + )
2,500
37
55,000
16.12
1.162 kg/H
48
1.930
1
—
Butane (I3 B /P )
3,175
28-30/50
55,000
16.12
1.162 kg/H
44
2.184
1
18.1
Propane (I3 P )
2,500
28-30/50
55,000
16.12
1.162 kg/H
44
2.184
1
24.9
Natural (I2 H /I2E )
1,000
15-30
90,000
26.38
2.549 M3/H
29
3.454
2
7.2
Natural (I2 L )
830
20-35
90,000
26.38
3.071 M3/H
29
3.454
2
8.9
Natural (I2 E L L )
830
15-30
90,000
26.38
3.071 M3/H
29
3.454
2
8.9
1,000
20
90,000
26.38
2.549 M3/H
35
2.794
2
—
830
25
90,000
26.38
3.071 M3/H
35
2.794
2
—
*Butane (I3+ )
3,175
28-30
90,000
26.38
1.901 kg/H
50
1.778
2
—
*Propane (I3 + )
2,500
37
90,000
26.38
1.901 kg/H
50
1.778
2
—
Butane (I3 B /P )
3,175
28-30/50
90,000
26.38
1.901 kg/H
47
1.994
2
18.1
Propane (I3 P )
2,500
28-30/50
90,000
26.38
1.901 kg/H
47
1.994
2
24.9
Natural (I2 H /I2E )
1,000
15-30
110,000
32.24
3.115 M3/H
22
3.988
2
6.9
Natural (I2 L )
830
20-35
110,000
32.24
3.753 M3/H
22
3.988
2
9.5
Natural (I2 E L L )
830
15-30
110,000
32.24
3.753 M3/H
22
3.988
2
9.5
1,000
20
110,000
32.24
3.115 M3/H
31
3.048
2
—
830
25
110,000
32.24
3.753 M3/H
31
3.048
2
—
*Butane (I3+ )
3,175
28-30
110,000
32.24
2.324 kg/H
48
1.930
2
—
*Propane (I3 + )
2,500
37
110,000
32.24
2.324 kg/H
48
1.930
2
—
Butane (I3 B /P )
3,175
28-30/50
110,000
32.24
2.324 kg/H
44
2.184
2
18.1
Propane (I3 P )
2,500
28-30/50
110,000
32.24
2.324 kg/H
44
2.184
2
24.9
Natural (I2 H /I2E )
T20
Nominal
Heating Value
*Natural (I2 E + )
*Natural (I2 E + )
*Natural (I2 E + )
*Natural (I2 E + )
mb
Shaded areas are stated in metric equivalents
* Gas valve’s internal regulator disabled.
** Consult factory for elevations over 2,000 feet (610 meters) for correct orifice size.
22
JLA Limited
113429 - 9
Important
Piping/Connections
T20
T30
T50
T 75
3 /8”
1/2 ”
1 /2 ”
1/2 ”
CE dryer connections will be B.S.P.T., all others will be N.P.T.
There should be a minimum 6-inch (15.24 cm) clearance
between the back guard and the first bend in the gas piping
for ease of servicing. It is recommended that a gas shutoff
valve be provided to the gas supply line of each dryer for ease
in servicing.
The size of the main gas supply line (header) will vary
depending on the distance this line travels from the gas meter
or, in the case of L.P. gas, the supply tank, other gas-operated
appliances on the same line, etc. Specific information
regarding supply line size should be determined by the gas
supplier.
Note
!
Undersized gas supply piping can create a low or
inconsistent pressure, which will result in erratic
operation of the burner ignition system.
!
Pipe joint compounds that resist the action of
natural, L.P., and butane gases must be used.
Test all connections for leaks by brushing on a soapy water
solution (liquid detergent works well).
!
Warning
Never test for leaks with a flame!!!
NOTES ______________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
TYPICAL NATURAL GAS INSTALLATION
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
TYPICAL L.P. GAS INSTALLATION
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
Consistent gas pressure is essential at all gas connections.
It is recommended that a 3/4-inch (19.05 mm) pipe gas loop
be installed in the supply line servicing a bank of dryers. An
in-line pressure regulator must be installed in the gas supply
line (header) if the (natural) gas pressure exceeds 13.0 in
WC (32.34 mb) pressure.
_____________________________________________________________
A plugged tap, accessible for a pressure gauge connection,
must be installed in the main gas supply line immediately
upstream of the dryers.
_____________________________________________________________
113429 - 9
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
Telephone 01422 822282
23
Converting from One Family
of Gas to Another ______________________
Warning (CE Dryers)
!
This appliance must only be operated with the gas
type indicated on the dryer’s data plate. If the
appliance is converted (gas type changed), a data plate
amendment must be obtained from JLA Limited (dryer’s
serial number is required to purchase a conversion kit).
Important
!
Any burner changes or conversions must be
made by a qualified professional.
The dryers manufactured for Belgium, Luxemburg, Greece,
Estonia, Slovak Republic, Iceland, Malta, Poland and Cyprus
cannot be converted from one family of gas to another.
Conversion from Natural Gas
to Propane or Butane Gas
Parts Required for Conversion:
*
**
***
****
!
Use extreme care when removing and replacing
orifice (injector). This orifice (injector) is made of
brass, which is easily damaged.
Reinstall the burner tube onto the burner base.
Use a flat screwdriver to remove the regulator vent cap.
• For unregulated L.P. gas (most countries): install
blocking pin (P/N 140414).
• For regulated L.P. gas (some countries): remove the
white plastic regulator adjustment screw (under vent
cap). Remove spring under screw and replace with
spring from kit (P/N 140416). Replace regulator
adjustment screw.
Install the gas train back into the dryer gas train enclosure.
Be sure the tab at the rear of the gas train engages into the
mounting slot.
Connect the union and the 3 electrical plugs.
The following conversion allows the dryer to be operated with
either propane, butane, or LPG. The use of gas valve kit (P/N
140414) disables the internal regulator of the gas valve.
Therefore, the gas supply is ungoverned and an external
regulator must be provided at the source of the supply
(example L.P. tank) or the gas supply line to the dryer. The
type of L.P. kit supplied will depend on the country the dryer is
installed in.
Description
Unregulated Gas Conversion Kit**
OR
Regulated L.P. Gas Conversion Kit****
Burner Orifice (Injector)
L.P. Conversion Label
Important
P/N
140414
Qty
***
140416
*
114515
***
***
1
Refer to page 22 for orifice (injector) size.
Required for unregulated propane or butane only.
T20 and T30 will require 1; T50 and T75 will require 2.
Required for regulated LPG or propane only.
Affix L.P. Conversion Label (P/N 114515) to the dryer’s data
label.
Complete L.P. Kit Conversion Confirmation Label (P/N
114083) and affix this label as close as possible to the dryer’s
existing dryer rating (data) label/plate.
Non-CE Dryers
Affix L.P. Conversion Rating Label Addendum (P/N 114090)
as close as possible to the dryer’s existing dryer rating (data)
label/plate.
CE Dryers
Affix new data plate label that came with the conversion kit.
Open all shutoff valves, reconnect electrical power to the dryer,
and test for leaks.
Important
!
Never test for leaks with an open flame!!! Use a
soapy water solution or product intended for that
purpose.
Instructions
Disconnect electrical power to the dryer.
Close all shutoff valves in dryer’s gas supply line.
Important
!
The T50 and T75 will require that the following
procedures be performed on both burner
assemblies.
Open the panel located just below the loading door.
Locate the gas train and disconnect the union, 3 electrical
plugs, and the gas train mounting screws from the burner.
Carefully slide the gas train out of the gas train enclosure.
(The carbon ignitor located at the far end of the gas train is
very fragile.)
Remove 2 burner tube mounting screws and remove burner
tube in order to gain access to the orifice.
Using a 3/8” wrench or socket, remove the existing orifice
and replace it with an orifice from the kit.
24
Unregulated Gas Valve
Regulate (govern) gas externally (refer to “Supply Pressure”
in chart on page 22) to the correct gas pressure for the gas
being used. Operate dryer through 1 complete cycle to ensure
proper operation.
JLA Limited
113429 - 9
Regulated Gas Valve
Refer to “Gas Pressure Adjustment” on this page to adjust
the gas valve to the appropriate burner pressure listed on
page 22. The supply pressure must also match what is
listed on page 22 for the type of gas to be used.
Important
!
Conversions done improperly can result in a fire or
explosion!
Conversion from Propane or Butane Gas
to Natural Gas
The following conversion allows the dryer to be operated with
natural gas.
Install the gas train back into the dryer gas train enclosure.
Be sure the tab at the rear of the gas train engages into the
mounting slot.
Connect the union and the 3 electrical plugs.
Open all shutoff valves, reconnect electrical power to the dryer,
and test for leaks.
Operate the dryer through 1 complete cycle to ensure proper
operation.
With dryer operating, check the manifold (burner) pressure
at the tap on the gas valve to ensure proper operating pressure
(refer to chart on page 22).
Gas Pressure Adjustment
Disconnect electrical power to the dryer.
Parts Required for Conversion:
Description
Vent Cap and Spring
Burner Orifice (Injector)
P/N
140415
*
Qty
**
**
* Refer to page 22 for orifice (injector) size.
** T20 and T30 will require 1; T50 and T75 will require 2.
Instructions
Disconnect electrical power to the dryer.
Close all shutoff valves in dryer’s gas supply line.
Important
!
The T50 and T75 will require that the following
procedures be performed on both burner
assemblies.
Open the panel located just below the loading door.
Locate the gas train and disconnect the union, 3 electrical
plugs, and the gas train mounting screws from the burner.
Carefully slide the gas train out of the gas train enclosure.
(The carbon ignitor located at the far end of the gas train is
very fragile.)
Remove 2 burner tube mounting screws and remove burner
tube in order to gain access to the orifice.
Important
!
The T50 and T75 will require that the following
procedures be performed on both burner
assemblies.
To adjust gas valve’s internal regulator, remove the regulator
vent cap with the regulator adjustment tool, which is located
on the back guard between the gas inlet and exhaust outlet
(refer to the illustration below for proper use of adjustment
tool). Be sure to use one of the wide ends of the adjustment
tool for removal of the vent cap. Once vent cap is removed,
the narrow end of the adjustment tool can be used to turn the
plastic adjustment screw in the valve. Turn the screw
clockwise to raise pressure and counterclockwise to lower
pressure.
Gas (burner) pressures are measured with the burner in
operation for all burner adjustment conditions. Therefore
once the necessary adjustments have been made, the dryer
must be operated in a heating cycle to verify that the pressure
is correct. If it is not correct, you must discontinue the power
to the unit and make further adjustments. Repeat these steps
as many times as necessary to achieve the correct burner
pressure. Once the adjustment of the valve is complete, the
vent cap must be replaced and sealed with, for example,
paint to prevent maladjustment by the user.
Using a 3/8” wrench or socket, remove the existing orifice
and replace it with an orifice from the kit.
Important
!
Use extreme care when removing and replacing
orifice (injector). This orifice (injector) is made of
brass, which is easily damaged.
Reinstall the burner tube onto the burner base.
Edge #1 for vent cap
Edge #2 for adjustment screw
Select from the following 3 options, the conversion to be
performed:
• Converting from unregulated L.P. to regulated natural
gas: use a flat screwdriver to remove the cap with
blocking pin and install the regulator vent cap from the kit
(P/N 140415).
• Converting from unregulated L.P. to unregulated
natural gas: no change to the regulator is required.
• Converting from regulated L.P. to regulated natural gas:
remove the white plastic regulator adjustment screw
(under vent cap). Remove spring under screw and
replace with spring from kit (P/N 140415). Replace
regulator adjustment screw.
113429 - 9
Warning (CE Dryers)
!
This appliance must only be operated with the gas
type indicated on the dryer’s data plate. If the
appliance is converted (gas type changed), a data plate
amendment must be obtained from JLA Limited.
Conversions done improperly can result in a fire or
explosion!
Telephone 01422 822282
25
Gas Pressure Testing _________________
Steam Information ____________________
For proper operation, the gas pressure must be correct,
consistent and maintained at the gas pressure rates shown
on page 22. Provisions are made at the gas valve for taking
gas pressure readings.
It is your responsibility to have all plumbing connections made
by a qualified professional to ensure that the steam plumbing
installation is adequate and conforms with local, state, and
country regulations or codes.
There are 2 types of devices used to measure gas pressure.
They are the spring/mechanical type gauge and the
manometer. The use of the spring/mechanical type gauge is
not recommended because they are very easily damaged
and are not always accurate. The preferred type of gauge is
the manometer because it is a simple device to use and is
highly accurate. A manometer is simply a glass or transparent
plastic tube with a scale graduated in inches or mb. When it
is filled with water and pressure is applied, the water in the
tube rises, showing the exact gas pressure.
Care must be exercised when leveling steam dryers into final
position. After leveling the dryer, check the downward pitch of
the heat exchanger from front to rear with a level. Likewise,
check the downward pitch of the return condensate manifold
toward its outlet part. Absence of these downward pitches
will result in probable water hammer and premature heat
exchanger fracture and leakage.
Gas Pressure Test Procedure
Turn gas cock in gas supply line to “OFF” position.
50 Hz dryers: Back out miniature screw inside pressure tap
and attach manometer (refer to the illustration on page 24).
60 Hz dryers: Install pressure tap and attach manometer (refer
to illustration on page 24).
Turn gas cock to “ON” position.
Start the dryer in Heat Mode and wait for ignition. Gas manifold
pressure should be as shown on page 22.
If the gas pressure needs to be adjusted, refer to “Gas
Pressure Adjustment” on page 25.
Once test is complete, turn gas cock to “OFF” position.
Remove manometer. Tighten screw inside the pressure tap
or install plug.
The presence of condensate in the steam will cause water
hammer and subsequent heat exchanger failure. The steam
supply connection must be taken from the top of a welldripped steam main. If the supply run-out to the dryer exceeds
25 feet (7.6 meters), it should be dripped just before the control
valve with a proper trap and dirt pocket.
Important
!
Failure to comply with the requirements stipulated
in this manual can result in component failure,
which will void the warranty.
Steam Coil pH Level
The normal pH level for copper type steam coils must be
maintained between a value of 8.5 to 9.5. For steel type
steam coils the pH level must be maintained between a value
of 9.5 to 10.5. These limits are set to limit the acid attack of
the steam coils.
Turn gas cock to “ON” position and check for leaks with soap
solution with main burner “ON.”
26
JLA Limited
Important
!
Coil failure due to improper pH level will void the
warranty.
113429 - 9
Important
Steam Requirements – High Pressure
!
Operating Steam Pressure
Model
Maximum
Heat Input
(Normal Load)
Consumption (Approx.)
@ 125 psi (8.6 bar)
Inlet /
Return
T20
150 psig*
1.0 MPa
1.2 Bhp
45 lb/hr
20.41 kg/hr
1/2” / 1/2”
T30
150 psig*
1.0 MPa
1.75 Bhp
63 lb/hr
28.58 kg/hr
1/2” / 1/2”
T50
150 psig*
1.0 MPa
3.75 Bhp
127.5 lb/hr
57.83 kg/hr
3/4” / 3/4”
T75
150 psig*
1.0 MPa
4 Bhp
136 lb/hr
61.69 kg/hr
3/4” / 3/4”
Shaded areas are stated in metric equivalents
* The minimum operating pressure for optimum results is 100 psig (689.47
kPa).
Installation Instructions
To ensure an adequate supply of steam is provided, be sure
that the steam supply lines and steam return lines are sized
and laid out as stipulated in this manual. Inadequate steam
supply lines and steam return lines or improper steam
plumbing will result in poor performance and can cause
component failure. Clean, dry steam must be provided to the
dryer.
Important
!
Steam coil failure due to water hammer by wet
steam will void the warranty.
The presence of condensate in the steam supply line will
cause water hammer and subsequent heat exchanger
(steam coil) failure. The steam supply connection into the
main supply line must be made with a minimum 10-inch
(25.4 cm) riser. This will prevent any condensate from draining
towards the dryer.
The steam supply line to the dryer must include a 12-inch
(30.48 cm) riser along with a drip trap and check valve. This
will prevent any condensate from entering the steam coil.
Flexible hoses or couplings must be used. The dryer vibrates
slightly when it runs and this will cause the steam coil
connections to crack if they are hard piped to the supply and
return mains.
Shutoff valves for each dryer should be installed in the supply
line, return line, and drip trap return line. This will allow the
dryer to be isolated from the supply main and the return main
if the dryer needs maintenance work.
Install an inverted bucket steam trap and check valve at least
12-inches (30.48 cm) below the steam coil as close to the
coil as possible. A trap with a minimum capacity of 100 lb
(45.35 kg) of condensate per hour at 125 psi (8.62 bar) is
needed for each unit. (Based on 2 times the steam
consumption per hour.)
The supply line and the return line should be insulated. This
will save energy and provide for the safety of the operator and
maintenance personnel.
Water pockets in the supply line, caused by low points, will
provide wet steam to the coil possibly causing steam coil
damage. All horizontal runs of steam supply piping should
be pitched 1/4-inch (6.35 mm) for every 1 foot (0.31 meters)
back towards the steam supply header causing the
condensate in the line to drain to the header. Install a bypass
trap in any low point to eliminate wet steam.
113429 - 9
Flexible hoses/couplings must be used. Coil
failure due to hard plumbing connections will void
the warranty.
Water Information _____________________
Before You Start
Check Local Codes and Permits
Call your local water company or the proper municipal
authority for information regarding local codes.
Important
!
It is your responsibility to have all plumbing
connections made by a qualified professional to
ensure that the plumbing installation is adequate and
conforms to local, state, and federal regulations or codes.
It is the installer’s or owner’s responsibility to see that the
required water pressure, pipe size, or connections are
provided. The manufacturer assumes no responsibility if
the fire suppression system is not connected, installed, or
maintained properly.
Installation
Water Supply
The fire suppression system must be supplied with a
minimum water pipe size of 1/2-inch (12.7 mm) and be
provided with 40 psi +/- 20 psi (2.75 bar +/- 1.37 bar) of
pressure.
If the rear area of the dryer or the water supply is located in an
area where it will be exposed to cold/freezing temperatures,
provisions must be made to protect these water lines from
freezing.
Warning
!
If the water in the supply line or water solenoid
valve freezes, the fire suppression system will be
inoperative!!
Water Connections
The water connection is made to the 3/4”-11.5 NH hose
adaptor, which is shipped in the tumbler and must be installed
to the 1/2” N.P.T. water connection, located at the upper rear
of the dryer. A flexible supply line/coupling must be used in
an effort to avoid damaging the electric water solenoid valve.
Note
!
The 3/4”-11.5 NH is a standard hose coupling
screw thread. It is not to be confused with 3/4”
N.P.T. The sealing of an NH connection is made with a
washer opposed to the mating threads of an N.P.T.
assembly. The 2 thread designs are not compatible.
It is recommended that a filter or strainer be installed in the
water supply line.
Telephone 01422 822282
27
Important
Preoperational Test ___________________
!
Flexible supply line/coupling must be used.
Solenoid valve failure due to hard plumbing
connections will void warranty.
All dryers are thoroughly tested and inspected before leaving
the factory. However, a preoperational test should be
performed before the dryer is publicly used. It is possible
that adjustments have changed in transit or due to marginal
location (installation) conditions.
The dryer is to be connected to the water mains using a
new hose set and the old hose set should not be reused.
Turn on electric power to the dryer.
Optional Manual Bypass
Provisions are made in the dryer’s fire suppression system
for the installation of an optional manual bypass. The
connections for the manual bypass are made at the “tee” or
“three way” fitting located in the outlet supply side of the water
solenoid valve. The manual ball cock shutoff valve must be
located outside of the dryer at a distance from the dryer where
it is easily accessible. The use and connection of this manual
bypass is at the option or discretion of the owner.
The water connection for the manual bypass is made to the
“tee” or “three way” fitting, which has a 3/8” F.N.P.T. and a
coupling must be used to provide the minimum 1/2-inch (12.7
mm) supply (feed) line.
Refer to the Operating Instructions for starting your particular
model dryer.
Gas Dryers
Open all shutoff valves.
When a gas dryer is first started (during initial start-up), it has
a tendency not to ignite on the first ignition attempt. This is
because the gas supply piping is filled with air, so it may take
a few minutes for the air to be purged from the lines.
Note
!
During the purging period, check to be sure that
all gas shutoff valves are open.
Electrical Requirements
No independent external power source or supply connection
is necessary. The 24-volt power to operate the fire
suppression system is accomplished internally in the dryer
(from the dryer controls).
A gas pressure test should be taken at the gas valve pressure
tap of each dryer to ensure that the water column pressure is
correct and consistent.
Note
Warning
!
Electrical power must be provided to the dryer at
all times. If the main electrical power supply to the
dryer is disconnected, the fire suppression system is
inoperative!!
Preparation for Operation/Start-Up ___
The following items should be checked before attempting to
operate the dryer:
• Read all “CAUTION,” “WARNING,” and “DIRECTION”
labels attached to the dryer.
• Check incoming supply voltage to be sure that it is the
same as indicated on the data label. In the case of 208
VAC or 240 VAC, the supply voltage must match the
electric service exactly.
• GAS MODELS – Check to ensure that the dryer is
connected to the type of heat/gas indicated on the dryer
data label.
• GAS MODELS – Be sure that all gas shutoff valves are in
the open position.
• Be sure all back panels (guards) and electric box covers
are in place.
• Be sure the service doors are closed and securely in
place.
• Be sure the lint door/drawer is securely in place.
• Rotate the tumbler (drum) by hand to be sure it moves
freely.
• Check bolts, nuts, screws, terminals, and fittings for
tightness and security.
• Check that the vent is connected to the dryer and is
exhausted to the outdoors.
• STEAM MODELS – Check to ensure all steam shutoff
valves are open.
28
!
Water column pressure requirements (measured
at the pressure tap of the gas valve body) must be
verified.
Important
!
In most cases there is no regulator provided in an
L.P. dryer. The water column pressure must be
regulated at the source (L.P. tank), or an external regulator
must be added to each dryer.
Electrical Dryers
Check to ensure that electric oven/contactor assembly is
activating.
Safety Related Circuits
Make a complete operational check of all safety related
circuits:
• Door Switch(es)
• Hi-Limit Thermostats
• Sail Switch
Make a complete operational check of all operating controls.
Tumbler Coating
The tumbler is treated with a protective coating. We suggest
dampening old garments or cloth material with a solution of
water and nonflammable mild detergent and tumbling them
in the tumbler to remove this coating.
Microprocessor Programs/Selections
Each microprocessor controller (computer) has been
preprogrammed by the factory with the most commonly used
parameter (program) selections. If computer program
changes are required, refer to the computer programming
manual which was shipped with the dryer.
JLA Limited
113429 - 9
Preoperational Instructions __________
Important
!
For more detailed information regarding the
microprocessor controller (computer), refer to the
microprocessor user’s manual included with the dryer.
Shutdown Instructions ________________
If the dryer is to be shutdown (taken out of service) for a
period of time, the following must be performed:
Discontinue power to the dryer either at the external disconnect
switch or the circuit breaker.
Discontinue the heat supply:
Coin Models
Gas Models – Discontinue the gas supply.
Microprocessor Controller (Computer)
Shut off external gas supply shutoff valve.
When the microprocessor controller (computer) is in the ready
state, the L.C.D. screen will display “Ready, Insert $XX.XX
(amount) to Start”.
Shut off internal gas supply shutoff valve located in the gas
valve burner area.
Steam Models – Discontinue the steam supply.
Insert coin(s). Once the correct “Amount to Start” has been
inserted, the L.C.D. will display “Select Temperature”.
Shut off external (location furnished) shutoff valves.
Select temperature by pressing “HI,” “MED,” or “LO.” The
cycle will start and the L.C.D. will display the Dry Cycle selected
and the remaining time.
Service/Parts Information ____________
The dryer will continue through the drying and cooling cycles,
until the vended time has expired.
Service must be performed by a qualified trained technician.
If service is required, contact the distributor from whom the
equipment was purchased. If the distributor cannot be
contacted or is unknown, contact the JLA Service Department
for a distributor in your area.
Note
!
To stop the dryer, open main door. Continuation of
the cycle will resume only after the door has been
closed and any one of the 3 temperature selections is
pressed.
Non-Coin Models
Microprocessor Controller (Computer)
The L.E.D. display reads “READY” (no cycle in progress).
Press the letter on the keypad corresponding to the cycle
desired (e.g. key “D”).
The dryer will then start (i.e. blower, tumbler, and heat).
The L.E.D. display will read MANUAL DRYING CYCLE D,
___MIN REMAIN.
Service
Note
!
When contacting the Service Department, be sure
to give them the correct model number and serial
number so that your inquiry is handled in an expeditious
manner.
Parts
Replacement parts should be purchased from the distributor
from whom the equipment was purchased. If the distributor
cannot be contacted or is unknown, contact the Parts
Department for a distributor in your area. Parts may also be
purchased directly from the factory by calling the JLA Parts
Department at 01422 822282 or you may FAX in your order at
01422 824390.
Note
Note
!
!
The dryer can be stopped at any time by pressing
the “STOP/CLEAR” key, at this time the dryer will
go into a cycle pause. If the “STOP/CLEAR” key is pressed
again at this point, the cycle that was in progress will be
cancelled and returned to the “READY” state.
When ordering replacement parts from the
distributor or the manufacturer, be sure to give
them the correct model number and serial number so that
your parts order can be processed in an expeditious
manner.
When the programmed drying time has expired, the non-coin
microprocessor controller (computer) will proceed into the
Cool Down Cycle.
Warranty Information _________________
Once the Cool Down Cycle begins at the end of the heat
cycle, the L.E.D. display will read COOL DOWN TEMP ___/
___ MINUTES remaining. At the end of the heat cycle, the
dryer will shut off the heat and continue the fan and tumbler
until the Cool Down Time or temperature is reached.
Returning Warranty Cards
Before any dryer leaves the factory test area, a warranty card
is placed on the inside of the main door glass. These
warranty cards are intended to serve the customer where we
record the individual installation date and warranty information
to better serve you should you file a warranty claim.
If a warranty card did not come with your dryer, contact the
JLA Warranty Department at 01422 822282.
Important
!
113429 - 9
A separate warranty card must be completed and
returned for each individual dryer.
Telephone 01422 822282
29
Note
!
Important
!
Be sure to include the installation date when
returning the warranty card(s).
The frequency of cleaning the lint screen can best
be determined from experience at each location.
Warranty
Weekly
For a copy of the commercial warranty covering your particular
dryer(s), contact the distributor from whom you purchased
the equipment and request a dryer warranty form. If the
distributor cannot be contacted or is unknown, warranty
information can be obtained by contacting the JLA Warranty
Department at 01422 822282.
Clean lint accumulation from lint chamber, thermostat, and
microprocessor temperature sensor area.
Note
Warning
!
Steam Dryers
!
Whenever contacting the factory for warranty
information, be sure to have the dryer’s model
number and serial number available so that your inquiry
can be handled in an expeditious manner.
Clean the steam coil fins. It is suggested that compressed
air and a vacuum cleaner with brush attachment be used.
Warning
Routine Maintenance _________________
Cleaning
A program and/or schedule should be established for
periodic inspection, cleaning, and removal of lint from various
areas of the dryer, as well as throughout the ductwork system.
The frequency of cleaning can best be determined from
experience at each location. Maximum operating efficiency
is dependent upon proper airflow. The accumulation of lint
can restrict this airflow. If the guidelines in this section are
met, the dryer will provide many years of efficient, trouble
free, and most importantly, safe operation.
!
When cleaning steam coil fins, be careful not to
bend the fins. If fins are bent, straighten by using
a fin comb, which is available from local air-conditioning
supply houses.
90 Days
Remove lint from gas valve burner area with a dusting brush
or vacuum cleaner attachment.
Clean any lint accumulation in and around the motor(s) casing
opening.
Note
!
Warning
!
Lint from most fabrics is highly combustible. The
accumulation of lint can create a potential fire
hazard. Keep dryer area clear and free from combustible
materials, gasoline, and other flammable vapors and
liquids.
Inspect and remove lint accumulation in customer furnished
exhaust ductwork system and from dryer’s internal exhaust
ducting.
Note
!
Suggested time intervals shown are for average
usage, which is considered 6 to 8 operational
(running) hours per day.
!
!
Dryer produces combustible lint and must be
exhausted to the outdoors. Every 6 months,
inspect the exhaust ducting and remove any lint buildup.
A back draft damper that is sticking partially closed can
result in slow drying and shutdown of heat circuit safety
switches or thermostats.
Suggested Cleaning Schedule
Every Third or Fourth Load
Clean the lint screen every third or fourth load. A clogged lint
screen will cause poor dryer performance. The lint door/
drawer is located just below the loading door of the dryer.
Open the lint door/drawer, brush the lint off the lint screen,
and remove the lint. Inspect lint screen and replace if torn.
To remove the lint drawer from the dryer, pull
drawer out approximately halfway. Press the lint
door/drawer stop downward and pull the drawer out.
30
The accumulation of lint in the exhaust ductwork
can create a potential fire hazard.
Do not obstruct the flow of combustion and ventilation air.
Check back draft dampers in the exhaust ductwork.
Inspect and remove any lint accumulation, which can
cause the damper to bind or stick.
Important
!
To prevent damage, avoid cleaning and/or
touching ignitor/flame-probe assembly.
Every 6 Months
Note
Note
To avoid the hazard of electrical shock,
discontinue electrical supply to the dryer.
When cleaning the dryer cabinet(s), avoid using harsh
abrasives. A product intended for the cleaning of
appliances is recommended.
7 Days After Installation
and Every 12 Months Thereafter
A competent professional should inspect bolts, nuts, screws,
setscrews, grounding connections and nonpermanent gas
connections (unions, shutoff valves, and orifices). Belts
should be examined. Cracked or seriously frayed belts
should be replaced. Complete an operational check of
controls and valves. Complete an operational check of all
safety devices (lint door/drawer switch, door switches, sail
switch, and hi-limit thermostats).
JLA Limited
113429 - 9
Data Label Information _____________________________________________________________
Standard Label
CE Label
When contacting JLA, the information on the data label is required to ensure proper service/parts assistance. The data label is
located at the upper left rear of the dryer behind the back guard.
1. Model Number – This describes the style of dryer and type of heat (gas, electric, or steam).
2. Serial Number – Allows the manufacturer to gather information on your particular dryer.
3. Type of Heat – This describes the type of heat for your particular dryer, gas (either natural gas or L.P. gas), electric, or steam.
4. Heat Input (For Gas Dryers) – This describes the heat input in British thermal units per hour (Btu/hr) or kilowatts (kW).
5. Orifice Size (For Gas Dryers) – Gives the number drill size used.
6. Electric Service – This describes the voltage and current rating for a particular model.
7. Gas Manifold Pressure (For Gas Dryers) – This describes the manifold pressure taken at the gas valve tap.
113429 - 9
Telephone 01422 822282
31
Part No. 113429
9 - 07/15/08 - 50
Download PDF

advertising