American International Scan 250 Scanner User Manual

Fusion Scan 250 EX™ General Information
Unpacking: Thank you for purchasing the Fusion Scan 250 EX™
by American DJ®. Every Fusion Scan 250 EX™ has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found
or parts are missing, please contact our toll free customer support
number for further instructions. Please do not return this unit to your
dealer without contacting customer support first.
Introduction: The Fusion Scan 250 EX™ is a six channel, DMX intelligent fixture. The fixture can used in three different operating modes;
stand alone, Master/Slave configuration, or DMX controlled. The
Fusion Scan 250 EX™ can be used as a stand alone sound active
fixture or used in multiples linked in a master/slave configuration. For
best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: American DJ® provides a toll free customer
support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
User Instructions
Rev. 3/08
American DJ®
6122 S. Eastern Ave.
Los Angeles Ca. 90040
www.americandj.com
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 2
Fusion Scan 250 EX™ General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Fusion Scan 250 EX™ Features
• DMX-512 Protocol Compatible (Six DMX Channels)
• 3 Operating Modes - Master/Slave; Stand Alone; DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• UC3 Controller (Not Included)
Fusion Scan 250 EX™
Warranty Registration
The Fusion Scan 250 EX™ carries a 1 year (365 days) limited warranty. Please fill out the enclosed warranty card to validate your
purchase and warranty. You may also register your product online at
www. americandj.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide
a copy of your proof of purchase invoice. Please contact American
DJ® customer support for a R.A. number.
Fusion Scan 250 EX™ Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
During operation the housing may become extremely hot. Avoid touching the unit with bare hands while in use.
American DJ® will not accept any liability for any resulting damages
caused by the non-observance of this manual or any unauthorized
modification to this unit.
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 3
Fusion Scan 250 EX™ !
Safety Precautions
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required volt
age for your unit.
•Do not attempt to operate this unit if the power cord has been frayed or broken. Please route your power cord out of the way of
foot traffic.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the top cover under any conditions. There are no user serviceable parts inside.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged in any way.
•Never operate this unit when it’s cover is removed.
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•This unit is intended for indoor use only, use of this product out
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power Cord Protection - Power cords should be routed so they are
not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the unit.
• Cleaning - Follow the directions on page 15.
•Heat -The unit should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 4
Fusion Scan 250 EX™
Set Up
Fusion Scan 250 EX™
Power Supply: Before plugging your unit in, be sure the source volt-
INPUT
OUTPUT
2
3
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 5
OUTPUT
SOUN
POWER
COMMON
DMX512 OUT
3-PIN XLR
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
1 Ground
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
3 Hot
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
POWER
DMX+,DMX-,COMMON
1
INPUT
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
POWER
Data Cable (DMX Cable) Requirements (For DMX
and Master/Slave Operation): The Fusion Scan
250 EX™ can be controlled via DMX-512 protocol.
The Fusion Scan 250 EX™ a six channel DMX unit.
The DMX address is set electronically using the
COMMON
controls on the side panel of the unit. Your unit and
DMX +
DMX512 OUT
3-PIN XLR
your DMX controller require a standard 3-pin XLR
DMX Figure 1
connector for data input and data output (Figure
1). If you are making your own cables, be sure to use standard two
Set Up
REMOTE
CONTROL
INPUT
SOUND
Notice: Be sure to follow
figures two and three when making your own
DMX512
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
REMOTE
CONTROL
INPUT
OUTPUT
POWER
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
SOUND
INPUT
conductor shielded cable (This cable may be purchased at almost all
professional sound and lighting stores). Your cables should be made
with a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
age in your area matches the required voltage for your American DJ®
Fusion Scan 250 EX.™ The American DJ® Fusion Scan 250 EX™ is
available in a 120v and 220v version. Because line voltage may vary
from venue to venue, you should be sure your unit voltage matches the
wall outlet voltage before attempting to operate you fixture. Also be
sure to only use the included I.E.C. power cable supplied with the unit,
this cable matches the voltage and current requirements of the unit.
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
DMX512
REMOTE
CONTROL
INPUT
SOUND
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
POWER
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 6
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Fusion Scan 250 EX™
Set Up
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
Fusion Scan 250 EX™
System Menu
Note: After making any adjustments in the operating
system, there is a 10 second delay.
ADDR - DMX Address Setting.
1. Tap the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER.
2. A number between 1-512 will be displayed and flashing.
Press the UP or DOWN buttons to find your desired address.
Press ENTER to set your desired DMX address.
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Tap the MENU button until “SLND” is displayed, press
ENTER. “MSTR”, “SL 1” or “SL 2” will be displayed.
2. Tap the UP or DOWN buttons until your desired setting is
displayed, press ENTER to confim and exit.
BLND - Blackout or Stand by mode.
1. Tap the MENU button until “BLND” is displayed, press
ENTER. Either Yes or No will be displayed.
2. To activate Blackout tap the UP or DOWN buttons until Yes is
displayed, press ENTER to confim and exit. The fixture will now
be in Blackout mode. To deactivate Blackout mode, select No
and press Enter.
I PAN - Pan Inversion
1. Tap the MENU button until “I PAN” is displayed, press ENTER.
Either NO or 1 will be displayed.
2. To activate the Pan inversion tap the UP or DOWN buttons
until I is displayed, press ENTER to confim and exit. To deactiAmerican DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 7
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 8
Fusion Scan 250 EX™
System Menu
Fusion Scan 250 EX™
System Menu
vate Pan inversion, select No and press Enter.
of the unit.
I TLT - Tilt Inversion
1. Tap the MENU button until “FHRS” is displayed, press
ENTER.
1. Tap the MENU button until “I TLT” is displayed, press ENTER.
Either NO or 1 will be displayed.
2. The display shows the running time of the unit. Press MENU
to exit.
2. To activate the Tilt inversion tap the UP or DOWN buttons
until I is displayed, press ENTER to confim and exit. To deactivate Tilt inversion, select No and press Enter.
VER - With this function you can display the version soft-
LED - With this function you can have the LED display
1. Tap the MENU button until “VER” is displayed, press ENTER.
turn off after 10 seconds.
1. Tap the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch off
after 10 seconds.
ware of the unit.
2. The display will now display the version of software. Press
MENU to exit.
RSET - Use this function to reset the unit.
1. Tap the MENU button until “RSET” is displayed, press ENTER.
2. The fixture will now reset.
3. Press ENTER to confirm and exit.
I DSP - This function will reverse the display 180º.
1. Tap the MENU button until “I DSP” is displayed, press ENTER.
2. Press ENTER to “flip” the display. Press ENTER to “flip” it
again. To save the adjustment press any other button.
TEST - This function will run a self test program. The
test program will test pan/tilt mirror movement, laser, and
colors.
1. Tap the MENU button until “TEST” is displayed, press ENTER.
2. The fixture will now run a self test.
FHRS - With this function you can display the running time
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 9
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 10
Fusion Scan 250 EX™
Laser Warning Labels
Fusion Scan 250 EX™
Operation
Operating Modes: The Fusion Scan 250 EX™ can operate in
three different modes. This next section will detail the differences in the operating modes.
• Stand alone mode The unit will react to sound.
• Master/Slave mode You can daisy chain up to 16 units together to get a synchronized
light show without the need of an external controller. The units will
react to sound chasing through the several built-in programs.
• DMX control mode This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation ® Show
Designer.™
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control mirror movement, the patterns and chases, and the shutter (strobe). A DMX controller allows
you to create unique programs tailored to your individual needs.
1. The Fusion Scan 250 EX™ uses six DMX channels. See page 14 for detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 8 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Stand-Alone Operation (Sound Active Mode): This mode allows
a single unit or several units linked together, to run to the beat of the
music.
1. Once you plug the fixture in, Sound Active mode is activated auto
matically. You can adjust the sensitivity by turning the knob on the top of the fixture.
2. The optional UC3 Controller (not included) may be used to con-
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 11
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 12
Fusion Scan 250 EX™
Operation
Channel
trol different functions including blackout.
Master-Slave Operation (Sound Active): This function will allow
you to link up to 16 units together and operate without a controller. The
units will be sound activated. In Master-Slave operation one unit will
act as the controlling unit and the others will react to the controlling
units programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. On the Master unit use the MENU button until “SLND” is displayed
press ENTER. Either “MAST”, “SL 1” or “SL 2” will be displayed. Press the UP or DOWN buttons to set the fixture to “MAST”, and press ENTER.
3. On the slave units tap the MENU button until “SLND” is displayed,
press ENTER. Set the fixture to either “SL 1” or “SL 2” and press ENTER.
4. The slave units will now follow the Master unit.
Note: When running fixtures in Master/Slave configuration “SL
1” will make the fixture do the opposite to the other fixture.
Example: Four fixtures linked together. On fixtures 1 and 3 set
the fixture 1 to “MAST” and set fixture 3 to “SL 1”, and set fixtures
2 & 4 to “SL 2”. Fixtures 1 & 2 will run the same and fixtures 2 & 4
will run opposite. This makes a great light show.
5. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Fusion Scan 250 EX™
Fusion Scan 250 EX™
Value
0 - 255
PAN
2
0 - 255
TILT
3
0 - 10
11 - 21
22 - 32
33 - 43
44 - 54
55 - 65
66 - 76
77 - 87
88 - 98
99 - 109
110 - 120
121 - 127
128 - 255
4
0 - 11
12 - 23
24 - 35
36 - 47
48 - 59
60 - 71
72 - 83
84 - 95
96 - 107
108 - 119
120 - 127
128 - 255
5
Blackout the unit
Function
1. Sync. Strobe
2. Sound Strobe
3. Two light Strobe
X/Y moving pattern
selection (12 patterns)
Gobo/Color Selection
Mode
Strobe/Sound
Pattern/Sound
Chase/Sound
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 13
Function
1
UC3 Control
Stand by
DMX Traits
0-7
8 - 15
16 - 131
132 - 247
248 - 255
COLOR WHEEL
WHITE
RED
DEEP BLUE
GREEN
YELLOW
ORANGE
PINK
LIGHT BLUE
UV PURPLE
MAGENTA
ORANGE + RED
LIGHT BLUE + MAGENTA
RAINBOW EFFECT SLOW - FAST
GOBO WHEEL
OPEN
GOBO 1
GOBO 2
GOBO 3
GOBO 4
GOBO 5
GOBO 6
GOBO 7
GOBO 8
GOBO 9
GOBO 10
GOBO WHEEL ROTATION SLOW - FAST
SHUTTER/STROBE
BLACKOUT
SHUTTER OPEN
STROBING SLOW - FAST
GOBO SHAKE SLOW - FAST
SHUTTER OPEN
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 14
Fusion Scan 250 EX™
Channel
Value
6
0-7
8 - 15
16 - 131
132 - 247
248 - 255
Fusion Scan 250 EX™ DMX Traits
Function
LASER
LASER OFF
LASER ON
LASER INTENSITY (VERY SUBTLE)
SOUND ACTIVE
LASER ON
Protective Mirror Cover
A metal cover is provided to protect the scanner mirror during
transportation and storage. The protective cover is held in place
by two thumb screws.
Fusion Scan 250 EX™
Lamp Replacement
This fixture is fitted with a halogen lamp which is
highly susceptible to damage if improperly handled. Never touch the lamp with your bare fingers
as the oil from your hands will shorten lamp life.
Also, never move the fixture until the lamps have
had ample time to cool. Remember, lamps are
not covered under warranty conditions.
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ® service
technician. Replacing with anything other than the specified part can
damage your unit and will void your manufactures warranty.
Warning: If you continue to blow lamps or fuses, STOP using the
unit. Contact customer support for further instructions, you may have
to return the unit for servicing. Continuing to use the unit may cause
serious damage.
Thumb Screws
Caution! Never open the unit when in use. Always disconnect the
main power before attempting to replace the lamp.
1. Be sure to follow the proper procedures when handling halogen bulbs.
2. Lamp replacement has been made simple by incorporating the use of two phillips screws.
3. Loosen and remove the phillips screws on the front bottom cover.
4. Remove the lamp cover and replace the bulb.
5. Reassemble.
Remember to always replace with the exact same type lamp and
fuse, unless otherwise specified by an authorized American DJ
service technician.
Fusion Scan 250 EX™
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 15
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 16
Fusion Scan 250 EX™ Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill. This will allow the unit to stay cooler and will extend the life of your fixture.
3. Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Fusion Scan 250 EX™ Trouble Shooting
No light output from the unit;
1.Be sure you have connected your unit into a standard 120v wall outlet.
2. Be sure the external fuse has not blown. The fuse is located on the bottom panel of the unit.
3. Remove the lamp holder and be sure the lamp is seated in its socket properly. Occasionally lamps become loose during ship-
ping be sure the lamp is push in to its socket all the way.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 17
Fusion Scan 250 EX™ Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 18
Fusion Scan 250 EX™ Model: Voltage*:
Lamp:
Dimensions: Colors:
Gobos:
Weight:
Fuse:
Beam Angle:
Duty Cycle:
DMX: Sound Active:
Working Position:
Warranty:
Specifications
Fusion Scan 250 EX™
120v/60Hz or 230v/50Hz
LL ELC 24V 250W
17.25”(L) x 7.5”(W) x 6”(H)
437mm x 191mm x 150mm
11 + White
10 + Spot
12 Lbs. / 5.2 kgs.
7Amp (120v & 230v)
15 Degree
None
6 Channels
Yes
Any Safe, Secure Position
1 Year (365 days)
*Voltage is preset at the factory and is not user selectable
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
American DJ® - www.americandj.com - Fusion Scan 250 EX™ Instruction Manual Page 19
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-582-2610
Web: www.americandj.com / E-mail: info@americandj.com