User Manual
English
APC Smart-UPS® RT – UXI/UXICH
8000/10000 VA 220/230/240 VAC
Tower/Rack-Mount 6U
Uninterruptible Power Supply
990-2687B 04/2006
Introduction
The APC Smart-UPS® RT is a high-performance, uninterruptible power supply (UPS) that provides
protection for electronic equipment from utility power blackouts, brownouts, sags and surges. The
UPS filters small utility line fluctuations and isolates electronic equipment from large disturbances
by internally disconnecting from utility line power. The UPS provides continuous power from the
internal battery until utility power returns to safe levels or the battery is fully discharged.
INSTALLATION
Read the Safety Instruction sheet before installing the UPS.
Unpacking
Inspect the UPS upon receipt. Notify the carrier
and dealer if there is damage.
The packaging is recyclable; save it for reuse or
dispose of it properly.
Check the package contents.
ƒ UPS
ƒ Front bezel
ƒ
Literature kit containing:
ƒ
Software CD
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Smart-UPS User Manuals CD
Serial cable
Six output power cords
Two battery cable assemblies
Two ground wires
Product documentation, warranty
information, and safety information
Network Management Card
documentation
ƒ
Specifications
TEMPERATURE
OPERATING
STORAGE
32° to 104° F (0° to 40° C)
5° to 113° F (-15 to 45 ° C) charge UPS battery every six months
MAXIMUM
ELEVATION
OPERATING
STORAGE
10,000 ft (3,000 m)
50,000 ft (15,000 m)
HUMIDITY
0% to 95% relative humidity, non-condensing
WEIGHT
UPS
UPS WITH
PACKAGING
244 lbs (111 kg)
284 lbs (129 kg)
1
This unit is intended for
indoor use only. Select a
location sturdy enough to
handle the weight.
Do not operate the UPS where
there is excessive dust or the
temperature and humidity are
outside the specified limits.
Ensure the air vents on the
front and rear of the UPS
are not blocked.
ATTACH THE BEZEL TO THE UPS
HARDWIRING INSTRUCTIONS
•
Wiring must be performed by a qualified electrician.
•
Adhere to all national and local electrical codes.
•
Install a utility circuit breaker for input wiring, (see tables below).
220/230/240 V MODELS
Input Connections
Output Connection (optional)
Single-Phase: Wire to L1, N, and
Three-Phase: Wire to L1, L2, L3, N, and
System
SURT8000
SURT10000
Wire to L1A, N1, and
.
.
.
Wiring
Number
of
Phases
Voltage
Current
Full Load
(Nominal)
External Input
Circuit Breaker
(Typical)
Wire
Size
(Typical)
Input
1
220/230/240 V
40 A
50 A / 2-pole
10mm2
Input
3+
Neutral
380/400/415 V
15 A / phase when
online
40 A on L1 in bypass
50 A / 4-pole
10mm2
Output
1
220/230/240 V
40 A
(not required)
10mm2
Input
1
220/230/240 V
50 A
63 A / 2-pole
16mm2
Input
3+
Neutral
380/400/415 V
18 A / phase when
online
50 A on L1 in bypass
63 A / 4-pole
16mm2
Output
1
220/230/240 V
50 A
(not required)
16mm2
2
1.
2.
3.
4.
5.
6.
Switch the UPS input circuit breaker (see A in diagram) and utility circuit breakers OFF.
Remove the input access panel, (see B in diagram).
Remove circular knockout.
Run appropriate size wire through the access panel, and connect to the terminal block,
(Green: Ground, Brown: Hot, Blue: Neutral). Connect the ground wire first. Use
appropriate strain reliefs, (not included).
For three-phase input, set the input phase selector switch, (see C in diagram) to “3”. For
single-phase input, leave the switch in the default position of “1”.
Replace the access panel.
3
CIRCUIT BREAKERS
8000/10000 VA
Input Circuit
Breaker
The input circuit breaker must be switched on for the UPS to operate.
The input circuit breaker protects the UPS from extreme overload
conditions.
8000/10000 VA
Output Circuit
Breakers
IEC 320-C13
10 A total current
from four
receptacles
IEC 320-C19
16 A for each
receptacle
BASIC CONNECTORS
Serial Com
Power management software and interface kits can be used with the UPS.
Use only interface kits supplied or approved by APC.
Any other serial interface cable will be incompatible with the UPS
connector.
Connect the UPS to the network using the Network Management Card.
Ethernet Port
Emergency Power Off terminal allows the user to connect the UPS to the
central EPO system.
EPO Terminal
TVSS Screw
External Battery
Pack Connectors
The UPS features a transient voltage surge-suppression (TVSS) screw for
connecting the ground lead on surge suppression devices such as telephone
and network line protectors.
When connecting grounding cable, disconnect the unit from the utility
power outlet.
External battery packs must be connected to these connectors located on
the rear panel of the unit.
4
CONNECT THE EXTERNAL BATTERIES
Battery Safety
Read and adhere to the following warnings when installing or servicing the external batteries.
Failure to observe these warnings may result in serious injury, death or damage to the
equipment.
WARNINGS
•
Do not attempt to install or service external batteries alone. A qualified
electrician should perform the installation and servicing of external
batteries.
•
Disconnect charging source(s) BEFORE connecting or disconnecting battery
terminals.
•
External batteries may retain lethal voltages after power has been disconnected
and all switches are off.
•
Use extreme caution when making terminal connections. Do not allow cables
to touch anything except the intended terminal.
PRACTICES
Always wear: Goggles or face shields
Acid-resistant, insulated gloves
Protective aprons
Protective overshoes or rubber boots
Always Use: Insulated tools
Rubber mats to cover batteries during servicing
Rubber mats or rubber stands on the floor
Adequate lifting devices
Remove:
Watches, rings, and other metal objects from your body
PRECAUTIONS
•
To avoid static build-up, service personnel should establish a grounding
contact prior working on batteries.
•
Do not lay tools or metal parts on top of batteries.
•
Lead-acid batteries contain hazardous, toxic materials.
ƒ Do not open, alter or mutilate batteries. Internal materials may be harmful
to the skin and eyes.
ƒ Do not dispose of batteries in a fire. There is danger of explosion.
•
Handle, transport and recycle batteries in accordance with local codes and
regulations.
APC BATTERY SOLUTION
See the APC Web site www.apc.com, or contact your APC dealer for information regarding the APC
external battery pack.
5
THIRD PARTY BATTERY SOLUTION
Batteries must be Sealed Lead-Acid type. Use 50 A, 250 VDC fuses with an Interrupt rating of
≥ 20,000 A.
Ensure that the external batteries are wired prior to connecting the batteries to the UPS.
Two separate, isolated 192 V battery systems are required when using a third party battery solution.
One cable assembly must be wired to each 192 V battery system. Two cable assemblies are included
with the UPS, one for each 192 V battery system.
Connect the Ground and Wire the Battery System
1.
Connect the ground wires (included), to each battery enclosure ground and the TVSS screw on
the back of the UPS.
2.
Cut off one of the connectors on each cable assembly revealing the positive and negative wires
in each cable.
3.
Connect the positive (red), and negative (black) wires to the positive and negative terminals on
each external battery system. Ensure that the proper polarities are connected.
4.
Plug the cable connectors into the battery connector receptacles on the back of the UPS.
Battery
System 1
Battery
System 2
6
CONNECT EQUIPMENT AND POWER TO THE UPS
1.
Connect equipment to the UPS.
2.
Turn on all connected equipment. To use the UPS as a master ON/OFF switch, ensure all
connected equipment is switched ON. The equipment will not be powered until the UPS is
turned on.
3.
Switch the utility circuit breaker on.
4.
To power up the UPS press the
5.
button on the front panel.
•
The UPS battery charges when it is connected to utility power.
•
Allow at least 24 hours for the batteries to fully charge prior to connecting equipment to the
UPS.
Configure the Network Management card. Refer to the Network Management card user manual.
7
TERMINAL MODE TO CONFIGURE UPS PARAMETERS AND PROGRAM THE NUMBER OF BATTERY
PACKS
Terminal Mode is a menu driven interface that enables enhanced configuration of the UPS.
Connect the serial cable from the computer to the serial com connector on the back of the UPS.
Instructions for use with PowerChute Network Shutdown software:
1.
2.
3.
Open a terminal program. Example: HyperTerminal
•
From the Desktop, go to Start => Programs => Accessories => Communication
=>HyperTerminal.
Double-click on the HyperTerminal icon.
•
Follow the prompts to choose a name and select an icon. Disregard the message, “...must
install a modem,” if it is displayed. Click OK.
•
Select the COM port that is connected to your UPS. The port settings are:
9 bits per second - 2400
9 data - bits 8
9 parity - none
9 stop bit - 1
9 flow control - none
•
Press ENTER
Example for setting the number of external battery packs:
Once the blank terminal window is open, follow these steps to enter the number of battery packs:
•
Press ENTER to initiate terminal mode. Press ENTER multiple times, until the prompt User
Name: is displayed. Follow the prompts. Type slowly, waiting until each character appears
on the screen prior to typing the next character.
Network Management card defaults:
•
User Name: apc
•
Password: apc
•
Press 1 and ENTER to select Device Manager.
•
Select the model by entering the corresponding number, then press Enter.
•
Press 3 and ENTER to select Configuration.
•
Press 1 and ENTER to select Battery.
•
Press 2 and ENTER to change the Battery Settings.
•
Type in the number of external battery packs.
Number of packs: 1= 1920 VAh, 2 = 3840 VAh, 3 = 5760 VAh, etc.
•
Press 3 and ENTER to accept the changes.
•
Press ESC multiple times (5) to return to the main menu.
•
Press 4 and ENTER to log out.
8
OPERATION
SMART-UPS RT FRONT DISPLAY
Load
Battery Charge
Indicator
Description
Online
The Online LED illuminates when the UPS is drawing utility power and performing
double conversion to supply power to connected equipment.
On Battery
The UPS is supplying battery power to the connected equipment.
Bypass
The Bypass LED illuminates indicating that the UPS is in bypass mode. Utility
power is sent directly to connected equipment during bypass mode operation.
Bypass mode operation is the result of an internal UPS fault, an overload condition
or a user initiated command either through an accessory or the manual bypass
switch. Battery operation is not available while the UPS is in bypass mode. Refer to
Troubleshooting in this manual.
Fault
The UPS detects an internal fault.
Refer to Troubleshooting in this manual.
Overload
An overload condition exists. Refer to Troubleshooting in this manual.
Replace
Battery
The battery is disconnected or must be replaced. Refer to Troubleshooting in this
manual.
Feature
Function
Power On
Press this button to turn on the UPS. (See below for additional capabilities.)
Power Off
Press this button to turn off the UPS.
9
Feature
Function
Normal/Bypass
Manual bypass enables the user to manually put connected equipment into bypass
mode. While in bypass mode the utility power bypasses the UPS and goes directly
to the connected equipment. Battery operation is not available while the UPS is in
bypass mode. Refer to Troubleshooting in this manual.
Cold Start
This is not a normal condition.
When there is no utility power and the UPS is off, press and hold the
to power up the UPS and connected equipment.
button
The UPS will emit two beeps. During the second beep, release the button.
Self-Test
Automatic: The UPS performs a self-test automatically when turned on, and
every two weeks thereafter, (by default). During the self-test, the UPS briefly
operates the connected equipment on battery.
Manual: Press and hold the
Diagnostic Utility Voltage
button for a few seconds to initiate the self-test.
The UPS has a diagnostic feature that displays the utility voltage. Plug
the UPS into the normal utility power.
The UPS starts a self-test as part of this procedure. The self-test does
not affect the voltage display.
Press and hold the
button to view the utility voltage bar graph
display. After a few seconds the five-LED, Battery Charge
display on the right of the front panel shows the utility input voltage.
Refer to the figure at left for the voltage reading (values are not listed on
the UPS). The display indicates the voltage is between the displayed
value on the list and the next higher value.
BATTERY OPERATION
The UPS switches to battery operation automatically if the utility power fails. While running on
battery, an alarm beeps four times every 30 seconds.
Press the
button to silence this alarm. If the utility power does not return, the UPS continues to
supply power to the connected equipment until the battery is fully discharged.
When two minutes of run time remain the UPS emits a continuous beeping. If PowerChute software
or the Network Management card are not being used, files must be manually saved and the computer
must be turned off before the UPS fully discharges the battery.
The UPS battery life differs based on usage and environment. Refer to www.apc.com for on battery
runtimes.
10
USER CONFIGURABLE ITEMS
NOTE: SETTINGS ARE MADE THROUGH SUPPLIED POWERCHUTE SOFTWARE, SMART SLOT
ACCESSORY CARDS, OR TERMINAL MODE.
FUNCTION
FACTORY
DEFAULT
USER SELECTABLE
CHOICES
DESCRIPTION
Automatic Self-Test
Every 14 days
(336 hours)
Every 7 days(168 hours),
14 days (336 hours)
On Startup Only,
No Self-Test
Set the interval at which the
UPS will execute a self-test.
UPS ID
UPS_IDEN
Up to eight characters to
define the UPS
Uniquely identify the UPS, (i.e.
server name or location) for
network management purposes.
Date of Last Battery
Replacement
Manufacture Date
Date of
Battery Replacement
mm/dd/yy
Reset this date when you replace
the battery module.
Minimum Capacity
Before Return from
Shutdown
0 percent
0, 15, 25, 35, 50, 60, 75,
90 percent
Following a low-battery
shutdown, the batteries will be
charged to the specified
percentage before powering
connected equipment.
Alarm Delay After
Line Failure
5 second delay
5 or 30 second delay
At Low Battery
Never
Mute ongoing alarms or disable
all alarms permanently.
Shutdown Delay
20 seconds
0, 20, 60, 120, 240, 480,
720, 960 seconds
Set the interval between the time
when the UPS receives a
shutdown command and the
actual shutdown.
Duration of
Low Battery Warning.
2 minutes
PowerChute
software provides
automatic,
unattended
shutdown when
approximately 2
minutes of battery
operated runtime
remains.
2, 5, 7, 10, 12, 15, 18,
20 minutes
The low battery warning beeps
are continuous when two
minutes of run time remain.
Change the warning interval
default to a higher setting if the
operating system requires a
longer interval for shutdown.
Synchronized Turn-on
Delay
0 seconds
0, 20, 60, 120, 240, 480,
720, 960 seconds
The UPS will wait the specified
time after the return of utility
power before turn-on (to avoid
branch circuit overload).
11
NOTE: SETTINGS ARE MADE THROUGH SUPPLIED POWERCHUTE SOFTWARE, SMART SLOT
ACCESSORY CARDS, OR TERMINAL MODE.
FACTORY
DEFAULT
FUNCTION
USER SELECTABLE
CHOICES
DESCRIPTION
High Bypass Point
+10% of
output voltage
setting
+5%, +10%, +15%,
+20%
Maximum voltage that the UPS
will pass to connected
equipment during internal
bypass operation.
Low Bypass Point
-30% of output
voltage setting
-15%, -20%, -25%, -30%
Minimum voltage that the UPS
will pass to connected
equipment during internal
bypass operation.
Output Voltage
230 VAC
200, 208, 220, 230,
240 VAC
Allows the user to select the
output voltage while on-line.
Output Frequency
Automatic
50 ± 3 Hz or
60 ± 3 Hz
Automatic
50 ± 3 Hz
50 ± 0.1 Hz
60 ± 3 Hz
60 ± 0.1 Hz
Sets the allowable UPS output
frequency. Whenever possible,
the output frequency tracks the
input frequency.
Number of Batteries
1
Number of Connected
Batteries
Defines the number of
connected batteries for proper
run time prediction.
Default setting of 1 = 1920 VAh
(192 V x 10 Ah)
Setting of 2 = 3840 VAh, etc.
12
CONNECT THE EPO (EMERGENCY POWER OFF)
The output power can be disabled in an emergency by closing a switch connected to the EPO.
Adhere to national and local electrical codes when wiring the EPO.
Wiring must be performed by a qualified electrician.
The switch should be connected to a normally open switch contact. External voltage is not required;
the switch is driven by 12V internal supply. In closed condition, 2mA of current are drawn
The EPO switch is internally powered by the UPS for use with non-powered switch circuit breakers.
The EPO circuit is considered a Class 2 circuit, (UL, CSA standards) and a SELV circuit (IEC
standard).
Both Class 2 and SELV circuits must be isolated from all primary circuitry. Do not connect any
circuit to the EPO terminal block unless it can be confirmed that the circuit is Class 2 or SELV.
If circuit standard cannot be confirmed, use a contact closure switch.
Use one of the following cable types to connect the UPS to the EPO switch:
•
•
CL2: Class 2 cable for general use
CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air.
•
CL2R: Riser cable for use in a vertical run in a floor-to-floor shaft.
•
CLEX: Limited use cable for use in dwellings and for use in raceways.
•
For installation in Canada: Use only CSA certified, type ELC (extra-low voltage control cable).
•
For installation in other countries: Use standard low-voltage cable in accordance with local
regulations.
13
MAINTENANCE, SERVICE
Battery Replacement
See your dealer or contact APC at the Web site, www.apc.com for information on replacement
battery modules.
Service
If the UPS requires service do not return it to the dealer. Follow these steps:
1.
Review the problems discussed in the Troubleshooting section of this manual to eliminate
common problems.
2.
If the problem persists, contact APC Customer Support through the
APC Web site, www.apc.com.
3.
ƒ Note the model number of the UPS, the serial number located on the back of the unit, and the
date purchased. If you call APC Customer Support, a technician will ask you to describe the
problem and attempt to solve it over the phone. If this is not possible, the technician will
issue a Returned Material Authorization Number (RMA#).
ƒ If the UPS is under warranty, repairs are free.
ƒ Procedures for servicing or returning products may vary internationally. Refer to the APC
Web site for country specific instructions.
Pack the UPS in its original packaging.
ƒ
If the original packing is not available, refer to the APC Web site, www.apc.com, for
information about obtaining a new set.
ƒ
Pack the UPS properly to avoid damage in transit. Never use Styrofoam beads for
packaging. Damage sustained in transit is not covered under warranty.
Always DISCONNECT THE BATTERY(S) before shipping in compliance with U.S.
Department of Transportation (DOT) and IATA regulations.
4.
Mark the RMA# on the outside of the package.
Return the UPS by insured, prepaid carrier to the address given to you by Customer Service.
14
TROUBLESHOOTING
Use the table below to solve minor installation and operation problems. Refer to the APC Web site,
www.apc.com, for assistance with complex UPS problems.
PROBLEM AND POSSIBLE
CAUSE
SOLUTION
UPS WILL NOT TURN ON
Battery not connected properly.
button not pushed.
Check that the battery connectors are fully engaged.
Press the
button once to power the UPS and the connected equipment.
UPS not connected to utility
power supply.
Check that the power cable from the UPS to the utility power supply is securely
connected at both ends.
Very low or no utility voltage.
Check the utility power supply to the UPS by plugging in a table lamp. If the
light is very dim, have the utility voltage checked.
UPS WILL NOT TURN OFF
button not pushed.
Press the
Internal UPS fault.
button once to turn the UPS off.
Do not attempt to use the UPS. Unplug the UPS and have it serviced
immediately.
UPS BEEPS OCCASIONALLY
Normal UPS operation when
running on battery.
None. The UPS is protecting the connected equipment.
UPS DOES NOT PROVIDE EXPECTED BACKUP TIME
Charge the battery(s). Batteries require recharging after extended outages. They
wear faster when put into service often or when operated at elevated
temperatures. If the battery(s) are near the end of their service life, consider
replacing the battery(s) even if the Replace Battery LED is not illuminated.
The UPS battery(s) are weak
due to a recent outage or
battery(s) are near the end of
their service life.
FRONT PANEL LEDS FLASH SEQUENTIALLY
The UPS has been shut down
remotely through software or an
optional accessory card.
ALL LEDS ARE OFF AND THE
The UPS is shut down and the
battery is discharged from an
extended outage.
None. The UPS will restart automatically when utility power returns.
UPS IS PLUGGED INTO A WALL OUTLET
None. The UPS will return to normal operation when the power is restored and
the battery has a sufficient charge.
BYPASS AND OVERLOAD LEDS ILLUMINATE, UPS EMITS A SUSTAINED ALARM TONE
The UPS is overloaded
The connected equipment exceeds the specified “maximum load” as defined in
Specifications on the APC Web site, www.apc.com.
The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.
15
PROBLEM AND POSSIBLE
CAUSE
SOLUTION
BYPASS LED ILLUMINATES
The bypass switch has been
turned on manually or through
an accessory.
If bypass is the chosen mode of operation, ignore the illuminated LED.
If bypass is not the chosen mode of operation move the bypass switch on the
back of the UPS, to the normal position.
FAULT AND OVERLOAD LEDS ILLUMINATE, UPS EMITS A SUSTAINED ALARM TONE
The UPS has ceased sending
power to connected equipment.
The connected equipment exceeds the specified “maximum load” as defined in
Specifications on the APC Web site, www.apc.com.
Disconnect nonessential equipment from the UPS to eliminate the overload
condition.
Press the OFF button, then the ON button to restore power to connected
equipment.
FAULT LED ILLUMINATES
Internal UPS fault.
Do not attempt to use the UPS. Turn the UPS off and have it serviced
immediately.
REPLACE BATTERY LED ILLUMINATES
Replace Battery LED flashes and
short beep is emitted every two
seconds to indicate the battery is
disconnected.
Check that the battery connectors are fully engaged.
Weak battery.
Allow the battery to recharge for 24 hours. Then, perform a self-test. If the
problem persists after recharging, replace the battery.
Failure of a battery self-test.
The UPS emits short beeps for one minute and the Replace Battery LED
illuminates. The UPS repeats the alarm every five hours. Perform the self-test
procedure after the battery has charged for 24 hours to confirm the Replace
Battery condition. The alarm stops and the LED clears if the battery passes the
self-test.
UPS OPERATES ON BATTERY ALTHOUGH LINE VOLTAGE EXISTS
Very high, low, or distorted line
voltage. Inexpensive fuel
powered generators can distort
the voltage.
Move the UPS to a different outlet on a different circuit. Test the input voltage
with the utility voltage display.
DIAGNOSTIC UTILITY VOLTAGE
All five LEDs are illuminated
The line voltage is extremely high and should be checked by an electrician.
There is no LED illumination
If the UPS is plugged into a properly functioning utility power outlet, the line
voltage is extremely low.
ONLINE LED
There is no LED illumination
The UPS is running on battery, or it is not turned on.
The LED is blinking
The UPS is running an internal self-test.
16
REGULATORY AND WARRANTY INFORMATION
Regulatory Agency Approvals and Radio Frequency Warnings
220, 230, 240 V MODELS
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not
installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to
take whatever measures may be necessary to correct the interference at their own expense.
BSMI
Limited Warranty
American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of
two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole
option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization
(RMA) number from customer support. Products must be returned with transportation charges prepaid and must be
accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does
not apply to equipment that has been damaged by accident, negligence, or misapplication or has been altered or modified in
any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of
purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s)
may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not liable for any costs, such as lost profits or
revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties,
or otherwise.
17
Declaration of Conformity
18
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following
ways:
•
•
Refer to the APC Web site to access documents in the APC Knowledge Base and to submit
customer support requests.
•
www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer
support information.
•
www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
Contact an APC Customer Support center by telephone or e-mail.
Local, country-specific centers:
go to www.apc.com/support/contact for information.
Contact the APC representative or other distributor from whom you purchased your APC product for
information on how to obtain local customer support.
Entire contents copyright 2005 American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part
without permission is prohibited.
APC, the APC logo, Smart-UPS, and PowerChute are trademarks of American Power Conversion Corporation. All other
trademarks, product names, and corporate names are the property of their respective owners and are used for informational
purposes only.
19