Troubleshooting guide | American Standard 2059 Indoor Furnishings User Manual

INSTALLATION
INSTRUCTIONS
For These Two-Piece Toilets:
Ellisse 2184
Deco 2059
Heritage 2176
Cadet III 13L 2650/2660
Baby Devoro 2315 Sonoma 2454
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
! CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
Regular Screwdriver
Wax Ring/Gasket
Adjustable Wrench
Flexible Supply Tube
Sealant
Closet Bolts
Tape Measure
Carpenters Level
1 REMOVE OLD TOILET
a.
b.
c.
d.
2
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must
be as listed below:
For 4110 Tanks: A = 10" (254mm)
FINISHED WALL
For 4114 Tanks: A = 14" (356mm)
For all other Tanks: A = 12" (305mm)
4
3
SEALANT
WAX RING
CLOSET FLANGE
F U T U R E
Putty Knife
Hacksaw
U S E
RECOMMENDED TOOLS AND MATERIALS
SUPPLY
AS
REQ'D.
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90°, and slide into place 6"
(152 mm) apart and parallel to wall.
A
FINISHED
FLOOR
5
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
6a
INSTALL TOILET
NUT
Position toilet squarely to wall
and, with a rocking motion, press
bowl down fully on wax ring and
flange. Alternately tighten nuts
until toilet is firmly seated on floor.
TAPERED
WASHER
CLOSET
BOLT
! CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
FLANGE
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP" must face up!
CLOSET FLANGE
Saniwares
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2000
7 3 0 5 13 - 1 0 0 R EV. D
S A V E
CLOSET BOLTS
F O R
A
6b
7a
INSTALL BOLTS AND CAPS
BOLT CAP
7b
For Tanks/Bowls using Speed
Connect System (Tank
mounting bolts pre-installed).
Ellisse 2184
Baby Devoro 2315
Deco 2059
Cadet III 13L 2650/2660
Sonoma 2454
CLOSET
BOLT
For all other Tanks/Bowls
RUBBER
WASHER
TANK MTG.
BOLTS PREINSTALLED
WASHER
NUT
Install caps on washers. (If necessary, cut bolt height
to size before installing caps.)
b. Smooth off the bead of sealant around base. Remove
excess sealant.
RUBBER
GASKET
TANK MTG.
BOLTS
RUBBER
GASKET
a.
HERITAGE 2176
COVER
COVER
MTG. CLIP
CLOSET
BOLT
WASHER
a.
b.
8
NUT
WASHER
WASHER
NUT
NUT
INSTALL TANK
a. Install large rubber gasket over
threaded outlet on bottom of tank
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening, and tank
mounting bolts go through mounting
holes. Secure with metal washers
and nuts.
b. With tank parallel to wall, alternately
tighten nuts until tank is snugged
down evenly against bowl surface.
!
Press covers over mounting clips. (If necessary,
cut bolt height to size before installing covers.)
Smooth off the bead of sealant around base.
Remove excess sealant.
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
INSTALL TANK
a. Install large rubber gasket over
threaded outlet on bottom of tank
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening.
b. Insert tank mounting bolts and
rubber washers from inside tank,
through mounting holes, and secure
with metal washers and nuts.
c. With tank parallel to wall, alternately
tighten nuts until tank is snugged
down evenly against bowl surface.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
9a
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
CONE
WASHER
EXISTING
WASHER
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
EXISTING
CONE
WASHER
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
WATER
SHUT-OFF
Use existing
coupling nut
and washer.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
9b
COUPLING
NUT
WATER
SHUT-OFF
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
WATER
SHUT-OFF
Captive cone
washers already
included. No
additional washers
needed.
With correct washers in place
(see Step 9a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
- 2 -
7 3 0 5 1 3 - 1 0 0 R EV. D
10
ARM
TOP
a.
REFILL
TUBE
NIPPLE
TANK
LEVER
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
Fig. 10A
"S"
CLIP
FLOAT
CUP
b.
FILL
VALVE
WATER LEVEL
ADJUSTMENT
CLIP
VALVE
BODY
FLUSH
VALVE
LINK
ADJUSTABLE
HEIGHT
ADJUSTMENTS
Adjust water level. Water level
should be adjusted to level
indicated on tank by adjusting float
cup. See Step 11 for water level
adjustment method.
If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 10A)
and take up slack on the chain, and
reinsert on lift rod. Make sure the
chain is not too taught.
11
FLAPPER
THREADED
SHANK
CONE WASHER
COUPLING NUT
(HAND TIGHT ONLY)
CARE AND CLEANING
!
WARNING: Do not use in-
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
Diagram 1
When cleaning your toilet,
wash it with mild, soapy
water, rinse thoroughly with
clear water and dry with a
soft cloth. Avoid detergents,
disinfectants, or cleaning
products in aerosol cans.
NEVER use abrasive
scouring powders or abrasive
pads on your toilet seat.
Some bathroom chemicals
and cosmetics may damage
the seat's finish.
tank cleaners. Products
containing chlorine (calcium
hypochlorite) can seriously
damage fittings in the tank.
This damage can cause
leakage and property
damage.
American Standard shall
not be responsible or liable
for any tank fitting damage
caused by the use of
cleaners containing
chlorine (calcium
hypochlorite).
Turn on water
supply. Adjust
water to
desired level
by squeezing
water level
adjustment clip
and moving
FLOAT CUP
up or down
along stainless
steel link.
SHANK
WASHER
LOCK NUT
12
7305 13 -10 0 REV. D
- 3 -
4650 Cadet 13L
4110 Baby Devoro
4392 Sonoma
4126 Deco
DESCRIPTION
TRIP LEVER
TRIP LEVER
TRIP LEVER (CHROME)
TRIP LEVER (POLISHED BRASS)
TRIP LEVER (GOLD)
TRIP LEVER
RIGHT HAND TRIP LEVER
BOLT CAP KIT (INCL TWO COVERS AND WASHERS)
BOLT CAP KIT (INCL TWO COVERS AND WASHERS)
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
FLUSH VALVE ASSEMBLY
FLUSH VALVE ASSEMBLY
FLUSH VALVE ASSEMBLY
FLUSH VALVE ASSEMBLY
FLUSH VALVE ASSEMBLY
COUPLING KIT, BOWL TO TANK KIT 232
COUPLING KIT, BOWL TO TANK KIT 233
COUPLING KIT, BOWL TO TANK KIT 230
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
FLUIDMASTER 400A VALVE
FLUSH VALVE ASSEMBLY
FLAPPER ASSEMBLY
COUPLING KIT, BOWL TO TANK KIT 184
4075 Ellisse
PART NO.
047242-XXX0A
730283-XXX0A
730288-002.XXX
730288-099.XXX
730288-094.XXX
047192-XXX0A
738172-XXX0A
034783-XXX0A
047227-XXX0A
738565-407.0070A
738565-406.0070A
738565-405.0070A
738565-404.0070A
738565-400.0070A
738181-0070A
738605-0070A
738461-0070A
738603-0070A
738484-0070A
730512-0070A
730519-0070A
730505-0070A
738258-0070A
738600-0070A
738392-0070A
738599-0070A
738397-0070A
738565-408.0070A
738676-0070A
738646-0070A
047188-0070A
4074 Heritage
REPAIR PARTS
Repair parts are determined by toilet tank number which can be found
marked inside tank. NOTE: "XXX" represents color or trim finish options.
Specify when ordering
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
TROUBLESHOOTING
13
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK
SLOWLY, repeat Step 13.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF
NON-USE, it is a signal you are wasting water because:
• The end of the refill tube is inserted into overflow pipe, below
water level in tank. Attach refill tube to overflow pipe using "S"
clip provided.
LIFT ARM
FIRST
LIFT ARM
FIRST
• The flush valve is leaking because it's worn, dirty or misaligned
with tank ball or flapper (replace with a new flapper).
IMPORTANT: Always
clear sand and rust from
system.
• Make sure water supply is
off. Remove valve TOP by
lifting arm and rotating top
and arm 1/8 turn
counterclockwise, pressing
down slightly on cap.
• While holding a
container over the
uncapped VALVE to
prevent splashing, turn
water supply on and off a
few times. Leave water
supply off.
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL
OF TANK WATER IS SLOW after valve has been in use for
some time, Fluidmaster Model 242 Replacement Seal may be
needed.
• Replace TOP by engaging
lugs and rotating 1/8 turn
clockwise. MAKE CERTAIN
TIP IS TURNED TO THE
LOCKED POSITION.
VALVE MAY NOT TURN
ON IF TOP IS NOT FULLY
TURNED TO THE LOCKED
POSITION.
Go to our website at www.fluidmaster.com for more
solutions to toilet problems.
For troubleshooting information please contact:
GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and
workmanship for a period of one year. Units returned to Fluidmaster will be replaced without charge.
30800 Rancho Viejo Road
San Juan Capistrano, CA 92675
(949) 728-2000 (800) 631-2011
www.fluidmaster.com
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster
shall not be responsible or liable for any damages caused by products used with Fluidmaster valves
that were not manufactured by Fluidmaster, Inc.
© 2001 Fluidmaster, Inc.
® Registered trademark of Fluidmaster, Inc.
TROUBLESHOOTING GUIDE
PROBLEM
Does not flush
Poor or sluggish flush
POSSIBLE CAUSE
a. Water supply valve closed.
CORRECTIVE ACTION
a.
Open valve and allow water to fill tank.
b. Supply line blocked.
b.
Shut off water supply, disconnect supply line, and inspect
all gaskets and washers. Reassemble. Also, see Fluidmaster
maintenance (see step 13).
c.
c.
Readjust chain length as required.
Flush valve chain too loose or disconnected.
d. Sand or debris lodged in water control.
d.
Shut off water supply. Remove cap and clean per Step 13.
a. Bowl water level too low.
a.
Check that refill tube is connected to water control and
inserted into tank overflow without being kinked or damaged.
b. Supply valve partly closed.
b.
Open supply valve fully. Be sure that proper supply tube size is used.
c.
c.
Remove obstruction. Consult a plumber if necessary.
d.
Normal supply pressure must be at least 20 psi.
Partially clogged trapway and/or drain pipe and/or vent.
d. Supply pressure too low.
Toilet leaks
Toilet does not shut off
a. Poor supply line connection.
a.
Review Step 9 of installation procedure.
b. Poor bowl to tank/floor connection.
b.
Review Step 4 through 7 of installation procedure.
a. Flush valve chain too tight, holding flush valve open.
a.
Readjust chain length as needed. Review step 10.
b. Flush valve seat and/or flapper worn or deformed.
b.
Replace flapper/flush valve assembly, as needed.
c.
c.
Shut off water supply. Remove cap and clean per Step 13.
Sand or debris lodged in water control.
AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American-Standard
will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building
or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other
damage; if it was not installed in accordance with American-Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by AmericanStandard.
American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall AmericanStandard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of
which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to
you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not
affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request
(including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard Inc.,
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
In Canada:
American-Standard,
2480 Stanfield Rd.,
Mississauga, Ontario
Canada L4Y 1S2
For residents of the United States, warranty information may also be
obtained by calling the following toll free number: (800) 442-1902
Toll Free: (800) 387-0369
7 3 0 513-100 REV. D
- 4 -
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Download PDF

advertising