American Standard 2471 Indoor Furnishings User Manual

American Standard 2471 Indoor Furnishings User Manual
Installation
Instructions
2471
THE
COLLECTION
™
by
CenterSet Faucet
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read
these instructions carefully before you begin.
Certified to comply with ASME A112.18.1M
Certifié ASME A112.18.1M
M968286
TOOLS REQUIRED
Channel Locks
1
Adjustable Wrench
Tubing Cutter
Basin Wrench
2
INSTALL FAUCET
CAUTION
Turn off hot and cold water supplies before beginning.
Apply a bead of PUTTY along the edge of the
underside of the BODY (1). Insert LIFT ROD (2)
through hole in BODY (1).
Insert faucet SHANKS through holes of SINK. Place
faucet as far forward as possible.
Plumbers' Putty or Caulking
SECURE FAUCET AND MAKE WATER
SUPPLY CONNECTIONS
Secure FAUCET (1) with ATTACHMENT NUTS (2) supplied.
(HAND TIGHTEN).
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
2
2
(HAND TIGHTEN)
1
1
SHANK
3
COUPLING NUT
PUTTY
4
FERRULE
SINK
3
INSTALL POP-UP DRAIN
1
Push Tail piece (11) down into Trap (C) (threaded end up).
2
Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side
up) onto Drain Body (10).
A
D
E
Apply a bead of Putty (D) to underside of Flange (2).
Feed Drain Body (10) up through Sink (A) and thread the
Flange (2) fully onto Drain Body (10).
3
Tighten Locknut (5) firmly, keeping the pivot rod hole pointed
towards the back of the sink.
Assemble Pivot Rod (9) as shown in Figure-4B. Notice the
position of the Concave Washer (G).
4
6
7
5
Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot
Nut (F).
10
Push TAILPIECE INSERT (12) into TAILPIECE (11) and push
TAILPIECE up and thread tightly into DRAIN BODY (10).
Position Extension Rod (7) onto Pop-Up Rod (E) and tighten
Thumbscrew (6).
Remove one end of Clip (8) from Pivot Rod (9) by squeezing
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
12
F
8
C
11
1-1/4"
9
F
"O" RING
Drop Stopper (1) into Drain Body (10).
4
5
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
FIGURE-4B:
G
Adjust stopper height by repositioning Extension Rod (7) and
tightening Thumbscrew (6).
CHECK DRAIN CONNECTIONS
Remove AERATOR (3).
Operate Pop-Up and fill lavatory with water. Check that
DRAIN STOPPER (1) makes a good seal and retains
water in lavatory. Adjust stopper height by repositioning
Pop-Up Rod (2) and tightening Thumbscrew (3).
Operate both HANDLES to flush
water lines thoroughly.
Release DRAIN STOPPER (1) and check all drain
connections and "P" trap for leaks. Tighten if necessary.
1
Replace AERATOR (3).
2
3
1
1
3
2
6
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
M968286
THE
COLLECTION
™
by
CenterSet Faucet
MODEL NUMBER
M961162-0070A
INDEX BUTTON (HOT)
M961163-0070A
INDEX BUTTON (COLD)
Replace the "YYY" with
appropriate finish code
CHROME
SATIN
002
295
2471
A918572-0070A
HANDLE SCREW
M962243-YYYOA
LEVER HANDLE
M962164-0070A
POP-UP ROD
M918049-0070A
ADAPTER
994053-0070A
VALVE
66070-YYY0A
AERATOR
066116-YYY0A
DRAIN STOPPER
066117-YYY0A
FLANGE KIT
065800-0070A
ATTACHMENT NUT
FLANGE
GASKET
953450-YYY0A
COMPLETE
DRAIN ASSEMBLY
024220-0070A
SUPPLY NUT
WASHER
070847-0070A
CLIP
LOCKNUT
072574-0070A
EXTENSION ROD
M961711-0070A
TAILPIECE INSERT
070532-0040A
TAILPIECE
066118-0070A
PIVOT ROD
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
M968286
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement