American Standard 2580 Indoor Furnishings User Manual
Add to my manualsadvertisement
Installation
Instructions
2580
T H E by
C O L L E C T I O N ™
BIDET FITTING
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
Required Tools
Roughing-in Dimensions
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
M 9 6 8 2 9 2
Flat Blade Screwdriver
Phillips Screwdriver
*Wrench
Tubing Cutter
Adjustable Wrench
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
BIDET OUTLINE
IS SYMBOLIC 7/8 DIA.
DOUCHE
SPRAY
ADJ. 1-1/4
TO 2-1/4
2-1/8
DIA.
3-7/8
1-3/8
DIA.
FINISHED
WALL
Channel Locks *Supplied with Fitting
1
MOUNTING BIDET FAUCET
CAUTION
Turn off hot and cold water supplies before beginning.
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and thread DECK ADAPTER (4) onto VALVE BODIE (2) until it locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Remove ESCUTCHEON (5), WASHER (10) and
UPPER GASKET (7) from TRANSFER VALVE (8) and insert into the center forward hole of BIDET.
Replace UPPER GASKET (7), and ESCUTCHEON (5) until it locks against the internal stop. Position the side threaded outlet rearward and secure
MOUNTING NUT (9).
4
3
BIDET
LEDGE
1
5
HOT
8
10
COLD
2
7
1-3/16
DIA.
1-3/8
MAX.
5-1/2
(C)
8 TO 12
(H)
1-1/4 O.D. TAILPIECE
2-1/4
DIA.
4-1/4
FINISHED
FLOOR
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
2
DRAIN INSTALLATION
Assemble O-RING (1), WASHER (2), PIVOT
ROD (3) and NUT (4) to DRAIN BODY (5).
Concave side of cup WASHER (2) is toward ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
8
Apply a bead of PUTTY to underside of FLANGE (9).
7
Feed DRAIN BODY (5) up through BIDET and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back of the BIDET.
6
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
9
PUTTY
BIDET
2
4
5
STOPPER
1
11
CLIP
3
9
10
3
8
SPRAY INSTALLATION
Assemble SPRAY BODY (1) to BIDET. Apply putty to underside of SPRAY BODY FLANGE (2) to seal and secure with NUT (3).
Thread SPRAY HOSE (4) with SEAL WASHER (5) to
SPRAY BODY (1). Connect other end of HOSE (4) with
SEAL WASHER (6) to bottom outlet NIPPLE (7) of the
TRANSFER VALVE (8).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
7
6
2
PUTTY
3
5
9
1
4
6
INSTALL HANDLES
LEVER HANDLES:
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
Thread HANDLE BASE (3) onto DECK ADAPTER (7)
Push HANDLE (4) onto ADAPTER (1).
Find correct position of HANDLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in HANDLE (4).
Secure HANDLE (4) with HANDLE SCREW (5).
Push INDEX CAP (6) in hole of HANDLE (4).
6
5
4
5
TEE AND HOSE CONNECTION
Insert SEAL (1) into ADAPTER (2) and tighten
ADAPTER (2) to side inlet of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2)
Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten.
3
6
Hot
6
5
4
2
1
Front
4
LIFT ROD GUIDE INSTALLATION
Unscrew LIFT ROD NUT (1) from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated into ESCUTCHEON of LIFT ROD
GUIDE (2).
Drop LIFT ROD GUIDE (2) into rear hole of bidet and from below secure with LIFT ROD
NUT (1).
3
2
1
Cold
DIVERTER KNOB:
Install HANDLE ADAPTER (8) onto valve stem (12).
Push DIVERTER KNOB (7) onto HANDLE ADAPTER (8).
Install RING (9) onto DIVERTER KNOB 7) and tighten with
SCREW (10).
Press on KNOB CAP (11).
11
10
9
TOP
3 7
Figure "A"
1
SPLINE END DOWN
2
8
12
7
M 9 6 8 2 9 2
7
WATER SUPPLY CONNECTIONS
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE
TO BE PURCHASED SEPARATELY
Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.
1
8
FINISH DRAIN INSTALLATION
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1) and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) and tightening THUMBSCREW (3).
Using metal TAILPIECE (5), make connection to the TRAP (6).
2
2
COUPLING NUT
1
3
3
7
1
Cold
FERRULE
5
4
9
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Operate both handles to flush water lines thoroughly. Turn
DIVERTOR (6) to rim wash and bidet spray.
Operate Lift Rod (3) and fill
Bidet with water. Check that
DRAIN STOPPER (4) makes a good seal and retains water in Bidet. Adjust stopper height by repositioning Lift Rod (3) and tightening Thumbscrew (5).
Release DRAIN STOPPER (4) and check all drain connections for leaks. Tighten if necessary.
2
4
1
5
6
2
3
6
10 SERVICE
To change direction of handle rotation, proceed as follows:
2
Turn valve to OFF position.
Remove HANDLE and
ADAPTER if present.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90
°
and replace.
Replace SPRING CLIP (1).
Replace HANDLE ASSEMBLY.
90
°
1
SPRAY (3) may accumulate dirt causing distorted and reduced water flow. Unscrew and remove
SPRAY (3) and rinse clean.
Replace SPRAY (3) and operate handles several times from
OFF to ON position. Do not force, handles turn only 90˚.
3
11
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT
WITH SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE
M 9 6 8 2 9 2
M962162-0070A
INDEX BUTTON (HOT)
M962163-0070A
INDEX BUTTON (COLD)
918428-0070A
HANDLE SCREW
T H E by
C O L L E C T I O N ™
BIDET FITTING
MODEL NUMBER
2581
M962165-YYYOA
LEVER HANDLE
918428-0070A
HANDLE SCREW
M962182-YYYOA
HANDLE
M908505-YYY0A
ESCUTCHEON
918049-0070A
HANDLE ADAPTER
M962161-0070A
DECK ADAPTER KIT
994053-0070A
CARTRIDGE
M961634-0070A
VALVE MOUNTING KIT
028704-0070A
TEE AND HOSE KIT
(INCLUDING SEALS)
030281-0070A
TRANSFER VALVE
MOUNTING KIT
060463-0070A
ADAPTER KIT
024220-0070A
COUPLING NUT 066116-YYY0A
DRAIN STOPPER
M962164-0070A
LIFT ROD
M953451-YYY0A
COMPLETE
DRAIN ASSEMBLY
066118-0070A
PIVOT ROD KIT
(5-7/16" lg.)
066117-YYY0A
2" FLANGE KIT
028646-0070A
SPRAY HOSE
CONNECTION KIT
M961656-YYY0A
LIFT ROD GUIDE
072574-0070A
EXTENSION
070847-0070A
CLIP
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 3
M961711-0070A
TAILPIECE INSERT
030280-0040A
TAILPIECE WITH
ESCUTCHEON
923348-0070A
HANDLE ADAPTER
013312-YYYOA
ESCUTCHEON KIT
953800-0070A
TRANSFER VALVE
028645-YYY0A
BIDET SPRAY
Replace the "YYY" with appropriate finish code
CHROME
SATIN
002
295
M 9 6 8 2 9 2
Installation
Instructions
2581
T H E by
C O L L E C T I O N ™
BIDET FITTING
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
Required Tools
Roughing-in Dimensions
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
M 9 6 8 2 9 3
FINISHED
WALL
Flat Blade Screwdriver
TRANSFER VALVE (FOR FLUSHING
RIM OR SPRAY)
BIDET OUTLINE
IS SYMBOLIC
7/8 DIA.
Phillips Screwdriver
Tubing Cutter
*Wrench
Adjustable Wrench
DOUCHE SPRAY
3-7/8
ADJ. 1-1/4
TO 2-1/4
2-1/8
DIA.
1-3/8
DIA.
*Supplied with Fitting Channel Locks
1
MOUNTING BIDET FAUCET
Turn off hot and cold water
CAUTION
supplies before beginning.
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and thread DECK ADAPTER (4) onto VALVE BODIE (2) until it locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODIES (2).
Remove MOUNTING NUT (9), FRICTION RING (10) and UPPER GASKET (7) from TRANSFER VALVE (8) and insert TRANSFER VALVE (8) into the center forward hole of BIDET.
Replace UPPER GASKET (7) and FRICTION RING (10).
Position the side threaded outlet rearward and secure
MOUNTING NUT (9). Thread ESCUTCHEON (5) onto
TRANSFER VALVE (8) until it seats against the
BIDET LEDGE.
5
9
10
4
3
BIDET
LEDGE
1
HOT
7
COLD
2
8
2
1-3/16 DIA.
1-1/4 MAX.
5-1/2
1-1/4 O.D. TAILPIECE
(C)
8 TO 12
(H)
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
2-1/4
DIA.
4-1/4
FINISHED
FLOOR
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
DRAIN INSTALLATION
Assemble O-RING (1), WASHER (2), PIVOT
ROD (3) and NUT (4) to DRAIN BODY (5).
Concave side of cup WASHER (2) is toward ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
8
Apply a bead of PUTTY to underside of FLANGE (9).
7
Feed DRAIN BODY (5) up through BIDET and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back of the BIDET.
6
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
STOPPER
9
PUTTY
2
BIDET
4
CLIP
3
1
5
11
10
3
TEE AND HOSE CONNECTION
Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to bottom of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2)
Connect HOSE COUPLING
NUTS (6) to Hot and Cold valve bodies and securely tighten.
Hot
6
2
4
COUPLING
NUT
5
3
1
Front
6
Cold
4
SPRAY INSTALLATION
Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with
NUT (3).
Screw SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY
BODY (1). Connect other end of HOSE (4) with SEAL
WASHER (6) to side outlet NIPPLE (7) of the TRANSFER
VALVE (8).
Screw SPRAY CAP (9) onto SPRAY BODY (1).
5
LIFT ROD GUIDE INSTALLATION
Unscrew LIFT ROD NUT (1) from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated into ESCUTCHEON of LIFT ROD
GUIDE (2).
Drop LIFT ROD GUIDE (2) into rear hole of bidet and from below secure with ROD GUIDE
NUT (1).
3
2
1
6
INSTALL HANDLES
LEVER HANDLES:
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
Thread HANDLE BASE (3) onto DECK ADAPTER (7)
Push HANDLE (4) onto ADAPTER (1).
Find correct position of HANDLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in HANDLE (4).
Secure HANDLE (4) with HANDLE SCREW (5).
Push INDEX CAP (6) in hole of HANDLE (4).
6
5
4
TOP
3
8
7
6
2
PUTTY
3
5
4
9
1
DIVERTER KNOB:
Install HANDLE ADAPTER (10) onto valve stem.
Push DIVERTER KNOB (9) onto HANDLE ADAPTER (10).
Install RING (11) onto DIVERTER KNOB (9) and tighten with
SCREW (12).
Press on KNOB CAP (13).
13
12
11
9
10
VALVE STEM
Figure "A"
1
2
SPLINE END DOWN
7
M 9 6 8 2 9 3
7
WATER SUPPLY CONNECTIONS
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE
PURCHASED SEPARATELY.
Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.
1
8
FINISH DRAIN INSTALLATION
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1) and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) and tightening THUMBSCREW (3).
Using metal TAILPIECE (5), make connection to the TRAP (6).
2
2
COUPLING NUT
1
3
3
7
1
Hot Cold
FERRULE
9
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Operate both handles to flush water lines thoroughly. Turn diverter to rim wash and bidet spray.
Operate Lift Rod (3) and fill
Bidet with water. Check that
DRAIN STOPPER (4) makes a good seal and retains water in Bidet. Adjust stopper height by repositioning Lift Rod (3) and tightening Thumbscrew (5).
Release DRAIN STOPPER (4) and check all drain connections for leaks. Tighten if necessary.
2
4
1
5
5
4
2
3
6
10
SERVICE
To change direction of handle rotation, proceed as follows:
2
Turn valve to OFF position.
Remove HANDLE and
ADAPTER if present.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90
°
and replace.
Replace SPRING CLIP (1).
Replace HANDLE ASSEMBLY.
90
°
1
SPRAY (3) may accumulate dirt causing distorted and reduced water flow. Unscrew and remove
SPRAY (3) and rinse clean.
Replace SPRAY (3) and operate handles several times from
OFF to ON position. Do not force, handles turn only 90˚.
3
11
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT
WITH SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE
M 9 6 8 2 9 3
918428-0070A
HANDLE SCREW
M961742-YYY0A
TRANSFER VALVE KIT
M962162-0070A
INDEX BUTTON (HOT)
M962163-0070A
INDEX BUTTON (COLD)
918428-0070A
HANDLE SCREW
M962165-YYYOA
LEVER HANDLE
M953131-0070A
TRANSFER VALVE
MOUNTING KIT
M908505-YYY0A
ESCUTCHEON
918049-0070A
HANDLE ADAPTER
M962161-0070A
DECK ADAPTER KIT
994053-0070A
CARTRIDGE
M961634-0070A
VALVE MOUNTING KIT
M921323-0070A
ELBOW ADAPTER
M961663-0070A
ADAPTER KIT
M962182-YYYOA
HANDLE
923348-0070A
HANDLE ADAPTER
M907617-YYY0A
ESCUTCHEON
TRANSFER VALVE
M953130-0070A
TRANSFER VALVE
024220-0070A
COUPLING
NUT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 3
028704-0070A
TEE AND HOSE KIT
(INCLUDING SEALS)
028645-YYY0A
BIDET SPRAY
028646-0070A
SPRAY HOSE
CONNECTION KIT
M961667-YYY0A
LIFT ROD GUIDE
M953451-YYY0A
COMPLETE
DRAIN ASSEMBLY
066118-0070A
PIVOT ROD KIT
(5-7/16" lg.)
M962164-0070A
POP-UP ROD
T H E by
C O L L E C T I O N ™
BIDET FITTING
MODEL NUMBER
2581
066116-YYY0A
DRAIN STOPPER
066117-YYY0A
2" FLANGE KIT
070847-0070A
CLIP
072574-0070A
EXTENSION
M961711-0070A
TAILPIECE INSERT
030280-0040A
TAILPIECE WITH
ESCUTCHEON
Replace the "YYY" with appropriate finish code
CHROME
SATIN
002
295
M 9 6 8 2 9 3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project